Alley Rally
Alley Rally (EXIDY, 1976) · Document · 20 pages · 18 sections · original scan
ALLEY RALLY SERVICE MANUAL
BY EXIDY
WARRANTY
EXIDY warrants all TV monitors and moving mechanical parts for a period of 90 days from data of purchase.
All printed circuit boards are warranted for a period of one full year from date of purchase.
Any questions regarding part replacement or service on failed parts will be dealt with on an individual basis.
Please contact your Jocal EXIDY distributor for service. Our distributors are authorized to deal directly with the EXIDY service and parts departments.
II
Il
IV
VI CONTENTS
GENERAL INFORMATION........ os
OBJECT OF THE GAME ..... eee cece teen re tenet eee e een 1
NORMAL OPERATION........ 0c eeeeee cece eeeee Wee ee webaee ot dee eee
SYSTEM FUNCTIONAL DESCRIPTION....... Stet en eee e eens sence
Power Supply Logic Printed Circuit Board (PCB) Coin Mechanism Start Switch Steering Units Pedal Units Speakers T.V. Monitor Shift Lever eal
TROUBLESHOOTING TIPS, ......-. 00 e cece eens eae ee ciceteeee nas ana 2
Picture Not Present Entire Picture Scrambled Picture Present but Partially Bad or Characters Act Incorrectly Bad Steering No Shift No Acceleration or Bad Acceleration No Game Start/Sound Present No Game Start/Sound Not Present Game Starts/No Sound
ADJUSTMENTS..........0.64 ee en ne re nee 4
Power Supply Adjustment Volume Adjustment Tone Adjustment Game Time Adjustments
{LLUSTRATIONS
Figure 1 DR System Block Diagram ......... 0... e cece cee teen eens 7 Figure 2 Power Supply (including Harness).......... 00000 ee eee ee eee cece ene 8° Figure 3 PCB Pot Locations (PCB AR-1A) ...... 0... cece cence eee eee 9 Figure 4 AR-1A Foot Pedal Assembly. . . . . . 10 Figure 5 AR-1A Steering Board... 0... ccc eee eee eee tenes 11 Figure 6 Steering Board Schematic ............ 06 c eee eee teens 12 Figure 7 AR-1A Wiring Diagram : : 13 Figure 8 Alley Rally Major Assembly ......... 0.0 cece eee tenet eens 16
TABLES
AR-1A Wiring List... 0.000. c cece cent een tte ete e nen ee 14 Illustrated Parts Index... 6... cece cece eee eee cent tee eee n eee 15
|. GENERAL INFORMATION:
ALLEY RALLY pits the player against the clock and four erratic “drone” cars. The drone cars drive a pseudo-random pattern, change directions, and even skid into the side of the track occasionally. Since they also change speed during all this, it becomes very difficult to drive around the track successfully without crashing into a drone car.
{l, OBJECT OF THE GAME:
The object of the game is quite simple. Drive around the track as long and as fast as you can without crashing into a drone car. You can drive either direction to make points, and you get a point each time you drive 1/4 of the way around the track.
ll. NORMAL OPERATION:
You drive one of two player cars. If you play a one player game, you drive the bright car which appears on the left side of the track, and you drive from the left side steering wheel. A two-player game adds a darker colored car which appears on the right side of the track, and is driven from the right side steering wheel.
The game is started only after the start button is depressed and the cars may move only after the foot pedal is depressed and the shift lever is in the LOW GEAR position.
When you crash into a drone car, the side of the track, or the other player’s car and you are in HIGH GEAR, your car will stop moving until you return the shift lever to the LOW GEAR position. When you crash into a drone car and you are still in LOW GEAR, your car will continue moving with only a slight hesitation. LOW GEAR, however, is slower and you cannot make points very rapidly unless you shift into HIGH GEAR as soon as possibie.
If, while you are driving in HIGH GEAR, you lift your foot completely off the foot pedal, you must again shift into LOW GEAR in order to start your car moving again.
When a quarter is inserted, one player is enabled. Add a second quarter and the second player is also enabled. When a player is enabled the game counter will set to 99, ready to count down, and the score counters will set to 00, ready to count up. When the game is started the game counter counts down to 00 and the game ends.
Sound for the cars begins when the quarter is inserted, and ends when the game is over.
1V. SYSTEM FUNCTIONAL DESCRIPTION (Refer to System Block Diagram, Figure 1)
115 VAC power is applied through interlock switch $1 (back door panel) to the power supply, the T.V. monitor, and the light fixtures.
The Power Supply converts this to +5 VDC and 24 VAC. The +5 VDC is used to power the LOGIC PCB (printed circuit board), Coin Counter, both steering units, and both foot pedal units (1 microswitch each). The 24 VAC is used to power the audio (sound circuitry located on the LOGIC PCB).
The Logic PCB generates all video (T.V. picture), audio (sound), and is the nerve center for all control functions.
The Coin Mechanism signals the LOGIC PCB that a one (1) or two (2) player gam can now begin, pending the pressing of the start switch. It also simultaneously signals the coin counter to advance one (1) count for each coin.
The Start Switch, when depressed, signals the LOGIC PCB that a game can now begin.
The Steering Units for player 1 and player 2 are identical, and each consists of a steering wheel, a shift lever, and a steering control board. The steering control board converts the rotation of the steering wheel into commands which are routed to the LOGIC PCB, which then interprets and executes these commands, causing the driven cars on screen to react accordingly.
The Pedal Units for player 1 and player 2 are identical, and each consists of a springloaded foot pedal and microswitch. The pedal, when in the “OFF” position (not depressed) does not trip the switch. Depression of the pedal trips the microswitch, telling the LOGIC PCB that the corresponding player is now in high gear. The image on screen will then react accordingly.
The Speakers, which are located in the overhead, receive their signal directly ftom the LOGIC PCB, and are not activated until the coin mechanism has been tripped by a coin. They will remain active only while a game is in progress. When the game ends, so does the sound.
The Shift Lever is part of the steering units, and its signal is developed by the microswitch located on the steering board.
V, TROUBLESHOOTING TIPS
The single most important factor in the proper operation of your ALLEY RALLY game is the power supply voltage adjustment. Before any troubleshooting can be done in the power supply, voltage must he checked and adjusted, if necessary. See “POWER SUPPLY ADJUSTMENT.”
PICTURE NOT PRESENT
Check:
1, 115 VAC system power
- +5 VDC power supply
- All harnesses connected
- T.V. brightness control
ENTIRE PICTURE SCRAMBLED
Check:
- T.V. horizontal hold control
- T.V. vertical hold control
- +5 VDC power supply adjusted 4, 22-pin connector on PCB not on backward.
PICTURE PRESENT BUT PARTIALLY BAD, or CHARACTERS ACT INCORRECTLY
Check:
- +5 VDC power supply adjusted
- Nothing external touching LOGIC PCB
- Harnesses all tightly connected
NO STEERING or BAD STEERING
Check:
- Red LEDs (lights) on steering boards flash when power is on and wheel is turned.
+5 VDC power supply Steering board harness connected.
If only one player has bad steering, the steering board can be tested by plugging the player 1 connector into the player 2 optical board (and vice versa). If this method is used, be extremely careful to insure the connector is not plugged in backward. Plugging the connector in backward will destroy the optical board. The Red LEDs on the steering board should, however, be an accurate indication of failure. No flash when the steering wheel is turned indicates a bad board or no power.
NO SHIFT
Check:
- All checks are the same as those listed under “NO STEERING or BAD STEERING,” above.
NO ACCELERATION or BAD ACCELERATION
Check:
- Foot pedals free to operate
- Microswitches on foot pedals
- Foot pedal harness connected 4, +5 VDC power supply
If only one player has bad acceleration, the foot pedal harnesses can be reversed for checkout of microswitches, if necessary, as outlined for steering problems under “NO STEERING or BAD STEERING” above.
NO GAME START/SOUND PRESENT
Check:
1. 2. 3. Start switch +5 VDC power supply Start switch harness connected
NO GAME START/SOUND NOT PRESENT
Check:
- Coin Mechanism — NOTE: Coin mechanism functions okay if drop of coin causes cars to reset to start position on opposite sides of the track. Left player should be facing up, right player should be facing down. +5 VDC power supply Harnesses connected
GAME STARTS/NO SOUND
Check:
1, 24 VAC from power supply
- Speaker harnesses connected
- +5 VDC on PCB developed from 24 VAC, used for sound.
Any problems which cannot be localized to other units probably indicate a bad LOGIC PCB, since it is the heart of the system. If another is available it should be temporarily placed in the bad game to see if the problem remains.
Vi. ADJUSTMENTS
POWER SUPPLY ADJUSTMENT
1. Connect voltmeter leads to +5V and GND traces on PCB, near 6 pin connector.
Adjust potentiometer R8 (Fig. 2) on power supply for +5.0 VDC as measured on the LOGIC PCB. The positive (+) lead of the voltmeter must be touching the large metal area (trace) on the non-component side of the LOGIC PCB which is connected to pins 2 and 5 of the 6-pin connector. The negative (—-) lead of the voltmeter must be touching the large metal area (trace) on the component side of the LOGIC PCB, which is connected to pins 1 and 6 of the 6-pin connector.
This voltage measurement must be made at the LOGIC PCB, since voltage losses may occur between the power supply and the LOGIC PCB. Adjustment of the power supply voltage made while measuring the voltage directly on the power supply terminals will not necessarily insure proper voltage to be present on the LOGIC PCB.
VOLUME ADJUSTMENTS (Refer to Fig. 3)
Volume controls are located on the LOGIC PCB and are as follows:
- Player one motor — R82
- Player two motor — R87
- Player one crash — R21
- Player two crash — R33
MOTOR SOUND ADJUSTMENTS (Refer to Fig. 3)
There are three pots each for player one and player two motor sound control. These adjustments are set up initially by the factory and should not be readjusted unless moved accidentally or during troubleshooting. Attempting to readjust the motor sounds by ear can be very difficult and time consuming. It is suggested that if these adjustments must be made, an oscilloscope be used to set up a pulse width on the 566 ICs as follows:
USING:
Pot R74 Plyr1 Pot R75 Pot R88
Pot R80 Plyr2 Pot R81 Pot R93
It should be noted, however, that these are “ballpark” adjustments and will most likely need some fine tuning to your own taste. Please contact our service department about SET:
2E pin 7 (actually pin 3 of chip) 2E pin 3 2F pin 7 (actually pin 3 of chip)
1E pin 7 (actually pin 3 of chip) 1E pin 3 1F pin 7 (actually pin 3 of chip)
any problems related to this adjustment procedure.
TONE ADJUSTMENTS
Tone controls are located on the LOGIC PCB and are as follows: (Refer to Fig. 3)
- Player one — R100
- Player two — R103 TO:
PW = 40 ms PW= 10 ms PW=6ms
PW = 40 ms
PW = 10ms
PW=6 ms
GAME TIME ADJUSTMENTS
A movable jumper wire, located on the LOGIC PCB near IC 4B, allows adjustment of the length of game time. The counter will always begin at 99 and begin to count down to 00 when the START button is depressed after a coin is inserted. The rate at which the counter counts down will vary, depending on the location of the jumper wire. Three options are available for a short, medium, and long game time. These are selected by placing the jumper wire on the appropriate terminal post. The approximate times are listed beside the posts on the PCB. These are 1 minute, 1.5 minutes and 2 minutes.
NDTE: GROUNDS SHOWN TO CLARIFY LOGICAL FUNCTIONS.
STEERING
UNIT 2
Locic pce
COIN
COUNTER
TO
LIGHT FIXTURE
POWER SUPPLY SPKR1 SPKR 2
INTERLOCK FUSE 5 AMP 115 VOC Figure 1. DR System Block Diagram
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
R82 (PLYR.2)
PLAYER1 VOLUME — R82 PLAYER 2 TONE — R103 R75 (PLya. 1)
R74 (PLYR. 1)
R80 (PLYR. 2)
PLAYER 1 CRASH VOLUME — R21
PLAYER 2 CRASH
VOLUME - R33 PLAYER1 TONE — R100
PLAYER 2 VOLUME — R87
Figure 3. PCB Pot Locations (PCB AR-1A)
BLUE ON WHITE
a
RIGHT PEDAL, REAR VIEW
LEFT PEDAL, REAR VIEW
Figure 4. AR-1A Foot Pedal Assembly
IR EMITTER PCB
TIL 31 IR EMITTERS
TIL 220 RED LEDs
TIL 81 PHOTOTRANSISTORS
Figure 5. AR-1A Steering Board
+5V +5V
“WwW
Tt /
A @® TEST
TIL 220
G82 yw
TIL 31
TH 220
MICROSWITCH
+5V
Figure 6. Steering Board Schematic
urexderq SUM VI-UV “2 emn8ty
LOGIC PCB ehhOeuanwvwliese@tesee eae a Nerooaoreoe Sry oeraatrseeSrse ‘= TT \ a | nn 7 Gaza N =e TAA PY eo 2¢ a2
Ji (PIN 1) Ji (PIN 2) Ji (PIN 3) J1 (PIN 4) Jl (PIN 5) Ji (PIN 6) J2 (PIN 2) 32 (PIN 3) J2 (PIN 4) J2 (PIN 2) J2 (PIN 3) J2 (PIN 4) J2 (PIN 5) J3 (PIN 9) J3 (PIN 14) J2 (PIN 9) J2 (PIN 10) J2 (PIN 11) J2 (PIN 13) J2 (PIN 14) J2 (PIN 15) J2 (PIN 16) J2 (PIN 18) 37 (PIN 1) J2 (PIN 21) P13 (PIN 2) P13 (PIN 1) P13 (PIN 7) P13 (PIN 8) P13 (PIN 9) J13 (PIN 2) 313 (PIN 1) J13 (PIN 7) J13 (PIN 8) J13 (PIN 9) P9 (PIN 1) J3 (PIN 11) J3 (PIN 10) J3 (PIN 13) J14 (PIN 1) J14 (PIN 2) J14 (PIN 3) J14 (PIN 4) J2 (PIN 6) J2 (PIN 7) J3 (PIN 5) J8 (PIN 4) 56 (PIN 3) J3 (PIN 3) J3 (PIN 8) J3 (PIN 7) J6 (PIN 4) J3 (PIN 6) J2 (PIN 20) J7 (PIN 2)
- Sense (P.S.) + Sense (P.S.)
#5 of xformer
#7 of xformer
+ Out
AR-1A WIRING LIST
FROM: To:
J9 (PIN 1) ~ Out
P3(PIN9) Start
P3(PIN14) J8 (PIN 1) P3(PIN5) J4 (PIN 4) P3 (PIN 4) J4 (PIN 3)
P8 (PIN 1) Coin counter
P6 (PIN 4) Foot pedal P6 (PIN 8) Foot pedal P3 (PIN 3) J4 (PIN 5) P3(PIN 8) J5 (PIN 4) P3 (PIN 7) J5 (PIN 3) P6 (PIN 6) Foot pedal P6 (PIN 5) Foot pedal P3 (PIN 6) J5 (PIN 5) P13 (PIN 5) + Out sense P13(PIN6) - Sense P13 (PIN 3) + Sense P13 (PIN 4) ~Out J13(PIN5) J3 (PIN 1) J13(PIN6) J3 (PIN 2) J13(PIN3) J6 (PIN 1) 313 (PIN 4) J6 (PIN 2) J13(PIN 4) J6 (PIN 2) P3(PIN1) J4(PIN1) P3 (PIN 2) J4 (PIN 2) P6(PIN1) Foot pedal +5V P6(PIN2) Foot pedal GND J7 (PIN 7) P10 (PIN 3) J7(PIN10) P10 (PIN 2) J7(PIN9) P10 (PIN 1) J4 (PIN 2) J4 (PIN 1) P3 (PIN 1) P3 (PIN 2) P8 (PIN 3) P8 (PIN 2) P11 (PIN 1) P11 (PIN 1) P11 (PIN 2) Pll (PIN 2) P11 (PIN 3) P14 (PIN 1) P14 (PIN 2) P14 (PIN 3) P14 (PIN 4) J12 (PIN 1) J12 (PIN 2) J14 (PIN 3) PWR cord 5A Amp fuse J10 (PIN 1) J10 (PIN 2) J10 (PIN 3) J12 (PIN 3) J12 (PIN 2) J12 (PIN 1) J11 (PIN 3) J11 (PIN 2) J11 (PIN 1) Start J5 (PIN 1) J8 (PIN 3) 38 (PIN 2) +5V Coin counter Ground coin mech.
Light Light Light Light Light w/safety ground Left speaker Left speaker Right speaker Right speaker N.O. inter. switch To power cord To power cord 5-amp fuse Com. inter. switch J11 (PIN 1) J11 (PIN 2) J11 (PIN 3) Safety ground #2 of xformer #8 of xformer P12 (PIN 3) P12 (PIN 2) P12 (PIN 1)
ALLEY RALLY 76-1040 ILLUSTRATED PARTS BLOW UP KEY TO LETTER INDEX SYSTEM
LETTER STOCK LETTER STOCK
| A-000 | 3/4 yellow 6 mil viny1 particle board | F-000 | 1/2 plywood |
| B-000 | —3/4 black vinyl particle board | G-000 | 2” pine brace |
| C000 | 3/4 plywood | H-000 = 1% pine bottom cleat | |
| D-000 = 3/4 particle board | 1-000 | 1/4 pin cleat | |
| E-000 | 3/4 mahogany cleat | J-000 | Miscellaneous metal part |
ALLEY RALLY 76-1040 ILLUSTRATED PARTS BLOW UP OVERALL DIMENSIONS IN INCHES
PART NO. DIMENSIONS — L x W PART NO. DIMENSIONS — L x W
| A001 | 27 3/8x 17 3/8 | 1039 | 15 13/16 (2 ea) |
| co02 | 27 3/8x 18 7/8 | E040 | 23/4 |
| A003 | 27 3/8x15 | C041 | 25 7/8x 3 1/4 |
| E004 | 12 7/8 (2 ea) | F042 | 27 3/8x11/4 |
| C005 | 271/8x 87/8 | £043 | 16 1/4 (2 ea) |
| C006 | 10 x 2 (2 ea) | £044 | 2 (2 ea) |
| C007 | 9 3/4 x 8 1/2 (2 ea) | F045 | 27 8/8 x2 |
| coos | 27 1/8 x 9 5/8 | D046 | 25 8/4 x 16 3/8 |
| co09 | 27 3/8x5 1/2 | G047 | 15 x 11/2 (2 ea) |
| A010 | 27 3/8x 11/2 | co4s | 23 3/4 x 2 3/8 (2 ea) |
| co11 | T1/2x2 | co49 | 14 5/8 x 4 (2 ea) |
| E012 | 7 (5 ea) | D050 | 27 1/4 x 3 (2a) |
| E013 | 2 (2ea) | E051 | 27 5/16 |
| E014 | 4 (2 ea) | E052 | 4 3/4 (2 ea) |
| Co15 | 7x6 (Zea) | E053 | 11/2 (2 ea) |
| D016 | T1j2x7 | 5054 | 13/8 |
| BO17 | 275/16 x 12 | C055 | 24 1/4 |
| BO18 | 12x 7 (3 ea) | C056 | 23 x 2 (2 ea) |
| E019 | 7 (3 ea) | HO057 | 21 x 11/2 (2ea) |
| B020 | 275/16 x 87/8 | D058 | 27 3/8 x 25 3/8 |
| F021 | 3x 2 3/4 (2 ea) | c059 | 12 7/8 x 3/4 |
| E022 | 26 3/8 | J060 | 3x 1/2 |
| B023 | 27 3/8x 31/4 | D061 | 23 3/4x1 |
| A024 | 71/2x71/8 | p062 | 23 3/4x3 |
| A025 | 71/8 x5 3/4 | E063 | 2 (2 ea) |
| A026 | 27 1/8x 141/16 | D064 | 23 3/4x 3 |
| J027 | 14 | DO65 | 12x 4 3/4 |
| A028 | 67 x 31 1/2 | D066 | 12x 43/4 |
| B029 | 27 3/8 x 14 3/4 | D067 | 23 3/4x3 |
| B030 | 45 3/16 x 27 5/16 | D068 | 12x 43/4 |
| E031 | 14 7/8 (2 ea) | D069 | a” |
| A032 | 67x 8311/2 | D070 | 23 3/4x1 |
| A033 | 27 3/8x 5 15/16 | 1071 | 37/8 |
| A084 | 27 3/8 x 2 | co72 | 8x 21/2 |
| G035 | 6 3/4x 1 1/2 (2ea) | co73 | 27 3/8x 21/8 |
| J036 | Lamp Socket (3 ea) | JO74 | 1/8 J mold 27 3/8 |
| F037 | 27 3/8 x2 | 3075 | 1/4 H mold 27 3/8 |
C038 27 3/8 x 23/4
Figure 8. Alley Rally Major Assembly