CATHODE RAY TOMES

Missile Command Sitdown TM-162 1st Printing

Missile Command (rev 3, A035467-02/04 PCBs) (Atari, 1980) · Technical Manual · 50 pages · 58 sections · original scan

Page 1

Operation, Maintenance

and Service Manual Complete with Illustrated Parts Lists

UMmOd-LI GINSMUUWOD

Page 2

JiT-DOWA

MNISitE COMMUN

Operation, Maintenance

and Service Manual

Complete with tilustrated Parts Lists

Puolished by: ATARI ING 1285 Borregas Avenue TE - P.O. Box 4 Sunnyvale, California 94086 5

Copyright © 1980 by Atari, Inc. All rights reserved. Na part of this publication may be reproduced by any mechanical. chotograonic. or electronic process. or in the form of a pnonagraphic recording, nor may st be siored in a retrieval system. transmitied. or otherwise cooied for DLolic Or private use. .vitmout cermissicn trom the puolisner.

Littegreones in ire USA. ad y aS j AL wane mrcners conta

Page 3

e GAME SERIAL NUMBER LOCATION

\ Your game’s serial number is stamped on a plate on the outside of the game. The same number Is also stamped on the chassis of the TV monitor, Regulator/Audio 1] PCB, and Game PCB. Please mention this number whenever cailing your distributor for service.

GAME SERIAL # IDENTIFICATION TAG

not

REGULATOR/AUDIO I PCS:

Page 4

‘Table of Contents

Location Setup A. New Parts : B. Unpacking and Setup..... 1, Removing Pallet and Attaching Legs

  • Installing Acrylic Panels .
  • Rerouting Power Cord C. Game Inspection . D. Game Installation. 1, Line Voltage Selection ...
  • Interlock and Power On/Off & Self-Test Procedure ..... F. Option Switch Settings .
  • Bonus Play Feature. .
  • Coin Mechanism Multipliers .
  • Examples of Option Switch Settings G. Game Play
  • Attract Mode .
  • Ready-to-Play Mod
  • Play Mode .........
  • High Score Initial Mode ... Switches . BODDAHS ROKK

Maintenance and Repair A. Cleaning B. Fuse Repiacement..... C. Opening the Contro! Panel ..

  • LED Switch Replacement. .
  • Trak Ball™ Maintenance and Repair. 213 D. TVMonitor Removal .............- +. 14 €. Printed-Circuit Board Replacement 1 15
  • Game PCB................ «15
  • Regulator/Audio I! PCB F. Opening the Attraction Panel . .
  • Replacing Fluorescent Tube .
  • Replacing Speaker ... G. Game Operation

Illustrated Parts Lists

Page 5

List of Ilustrations

Figure 1 Figure 2 Figure 3 Figure 4 Figure §

+ Figure 6 Figure 7 “Figure 8 Figure 9 Figure 10

Figure 11 Figure 12 Figure 13 Figure 14

Figure 15 Figure 16 Figure 17 Figure 18 Figure 19

Figure 20 Figure 21 Figure 22 Figure 23 “Power Supply Assembly for Color Raster-Scan Games ... Overview of Game Installation Requirements . Line Voltage Selection .... Interlock and Power On/Off Switches . gree - Location of Self-Test Switch, Volume Control and Option Switches . .

Self-Test Procedure Option Switch Settings . Opening the Control Panel . Trak Bali™ Maintenance and Rep ae TV Monitor Removal ..... 0.0.6 cece cece ence eee eee teen eee 14 Orn Oban

Game and Regulator/Audio Il PCB Replacement . Fluorescent Tube and Speaker Replacement .. Power Distribution Signa! Distribution

Ilustrated Parts Lists: ‘ Cabinet-Mounted Assemblies ..... Control Panei Assembly .. . Trak Bail™ Assembly ... Steering Printed-Circuit Board Assembly . Fluorescent Light Assembly

Regulator/Audio ll PCB Assembly ........... Missile Command™ Game PCB Assembly New Coin Door S288 BRBER

Page 6
NOTE

7 \f reading through this manual does not lead to solving a certain maintenance problem, call Tele-Help™ at the Atari Customer Service office in your geographical area, as shown in one or the two maps below. Order all parts from the California office.

WEST and CENTRAL U.S.A.

Parts for all Atari Customers. Sales and Service

Atari Coin-Op Customer Service 1344 Bordeaux Drive, Sunnyvale, CA 94086 Telex 17-1103 (Monday - Friday, 7:30 - 4:00 pm Pacific Time) om From California, Alaska or Hawaii “ (408) 745-2900

= From anywhere else in this area toll-free (800) 538-1611

EAST U.S.A.

Saies and Service Caly

Atari Inc. New Jersey Customer Service Office Cottontail Lane, Somerset, NJ 08873 Telex 37-9347

(Monday - Friday, 7:30 - 4:00 pm Eastern time) ~

From New Jersey ™ (201) 469-5993

z From anywhere else in this area toll-free (800) 526-3849

Page 7

Notice Regarding Non-Atari Parts

WARNING

Use of non-Atari parts or modifications of your Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players,

Atari, Inc.'s warranty (printed on the inside back cover of this manual) may be voided, if you do any of the following: 1.) you substitute non-Atari parts in your coin-operated game, or 2.) you modify or alter any circuits in your Atari game by using kits or parts not suppl by Atari. Not only may the use of any non-Atari parts void your warranty, but any such alteration may also adversely affect the safety of your game, and may cause injury to you and your players.

Page 8

Se IRE

AAWARNING - SHOCK HAZARD A

This game is designed to be connected only to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electric shock if this game is not properly grounded!

Location Setup

A. New Parts

The Sit-Down Missile Command™ game has three new parts. If you have worked on Atari games in the past, then you should be aware of these important differences. The new parts are: Color TV Monitor. Made especially to Atari specifications by Electrohome, Ltd., the 25-inch monitor has been color-converged at the factory. All convergence adjustments are cemented and locked in place, to prevent accidental changes. Important Note: The monitor's horizontal-yoke connectors have been re-

versed, to provide proper screen orientation in

this sit-down cabinet. Power Supply Assembly. It covers a wider voltage range than before, has higher reliability, a smaller overail size, and all fuse numbers and

fuse amperages are marked directly on the an almost complete environment for the player

metal chassis. Sit-Down Cabinet. This new ‘cabinet provides an almost complete environment for the player. The large 25-inch monitor screen’ and halfsilvered mirror create an illusion of great cabinet depth. In addition, a large speaker directly above the player's head projects the exciting audio. Potential players standing behind the game can view the missile attacks over the player's shoulders, by looking thru the windows in the cabinet.

Sit-Down Missite Command™

Page 9

. COLOR TV MONITOR

TV MONITOR SHIELD

COIN DOOR

REGULATORY AUDIO It PCB.

LOWER REAR VENTILATION FAN ACCESS PANEL

POWER SUPPLY ed

Figure 1 Overview of Game ATTRACTION PANEL

TRAK BALL™ CONTROL,

+

Page 10

e

@ Oem These new parts, as well as all other major parts in the game, are illustrated in Figure 1. Throughout this manual, wherever one of these new parts is mentioned, you will see this symbol:

B. Unpacking and Setup

After removing the steel strapping and cardboard packaging materials, you will have to remove the pallet on which your Sit-Down Missile Command™ was shipped. You also must unpack the acrylic window panet and graphics attraction panel and mount these in the rear opening of the game.

Setup involves inserting the four cabinet-leveling legs into the base. While you are inserting the legs into the base, be aware that this game weighs about 580 pounds! In addition, you may choose to route the AC power cord through the base, if you want to have the game free-standing.

  • Removing Pallet and Attaching

Legs

First, bring the game as close as possible to its final location. Now use a wrench and locate the four bolts that secure the pallet to the game’s base (these are near the four corners). You must reach in between the two layers of the pallet to loosen the bolts and remove them. Lift game from pallet.

Second, remove the four cabinet-leveling legs from the coin box. Have an assistant tilt the game slightly to one side, and screw two legs into the T-Nuts provided at the base. Tilt the game in the other direction and repeat for the remaining two legs.

  • Installing Acrylic Panels Remove the package of two acrylic panels and envelope of screws that are taped to the control panei and seat. Peel off the protective paper backing on the smoke-color window panel. Place this panel in the lower half of the game’s rear opening.

Using an Allen wrench, remove the three screws that secure the black metal retainer strip at the top rear of the game. Place the bottom edge of the graphics attraction panel in the slot behind the wood retainer strip. Secure the top edge of this pane! with the metal retainer strip and its three Allen-head screws. In addition, use the two screws

‘ Sit-Oown Missile Command™

in the envelope for securing the left and right edges of this panel (it has pre-drilled holes).

  • Rerouting Power Cord Now decide if you want to place the game against a wail or have it free-standing. If you choose a location against a wall, push the game so its front end (where the power cord exits) Is near the wall. If you have an arcade with a floor-mounted power outlet and want the game free-standing, reroute the power cord through the base as follows.

Unlock and open the rear access panel. Remove the small 2¥2-inch-square cover plate secured to the base of the cabinet. Open the control panei (see Figure 8) and remove the power cord plate inside the front cabinet wall. Do not disassemble the cord from this plate. .

Pull the cord inside the game and route it through the large hole near the console, down to the area underneath the seat. Push the plug through the hole in the base, and secure the power cord plate to the cabinet base. You will have excess cord, but you can easily store it inside the game.

Reattach the smail cover plate to the inside of the front cabinet wall. Close both the control pane! and the rear access panel. .

C. Game Inspection

This new game is ready to play upon removal from the shipping carton. However, your careful inspection is needed to supply the final touch of quality control. Please follow these steps to help us insure that your new game was delivered to you in good condition. .

[__conata NOTE env | Oo not plug the game in yet!

+

  • Examine the exterior of the game cabinet for dents, chips, or broken parts. Unlock and open the two access panels of the cabinet and inspect the interior of the game as foliows: /
Page 11

Sit-Oown Missile Command™

For voltage ratings and colors of all four voltage selection plugs, see text under “t. Line Voltage Selection.”

VOLTAGE

Figuré-3 Line Voltage Selection

@ Check that all plug-in connectors (on the game harness) are firmly seated. Replug any connectors found unplugged. DON'T FORCE CONNECTORS TOGETHER. The connectors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB.

AN — WARNING To avoid possible unpleasant electrical shock, do not touch internal parts of the TV monitor with your hands or metal objects held in your hands!

@ Check that ail plug-in integrated circuits on the game PCB are firmly seated in their sockets. @ Note the location of the game’s serial number—it is printed on the special label on the outside of the game cabinet. Verify that the serial numbers also stamped on the Game PC8, Regulator/Audio Il PCB and TV Monitor are ail identical. A drawing of the serial number locations is on the inside front cover of this manual. Please mention this number whenever you call your distributor for service. “@ Check all major assemblies such as thé

  • power supply, control panel and TV moni-

tor for secure mounting. For the safety of

players, be certain that all green ground wires are secured at their terminations.

D. Game

Installation

Figure 2. Installation Requirements Power Approximately 289 watts Temperature 0 to 38° C (32 to 100°F) Humidity Not over 95% relative Space Required 75x 118¥2 cm (29% x 46% in.) Game Height 198 cm (78in) ~

  • Line Voltage Selection Before plugging in your game, make sure that the voltage selection plug on the power supply (see Figure 3) Is correct for your location's line voltage. Check the wire color on the plug and see if it is correct per the list below. +

Line Voltage Range Voltage Selection Plug Color

-90-110 VAC (100) Violet 105-135 VAC (120) Yellow 200-240 VAC (225) Blue 220-260 VAC (240) Srown

Page 12

e FRONT ACCESS PANEL INTERLOCK SWITCH

POWER ON/OFF SWITCH COIN DOOR INTERLOCK SWITCH ATTRACTION PANEL INTERLOCK SWITCH

LOWER REAR ACCESS PANEL INTERLOCK SWITCH

Figure 4 Interlock and Power On/Off Switches

  • Interlock and Power On/Oft Switches To minimize the hazard of electrical shock while working on the inside of the game cabinet, four interlock switches have been installed (see Figure 4). One is located behind each of the two access panels, one is behind the acrylic attraction panel, and the fourth one is behind the coin door. These switches remove all AC line power from the game circuitry when any door or panel is opened.

Check for proper operation of the interlock switches by performing the following steps: @ Plug the AC line power cord into an AC outlet. @ Make sure to close the access panels and the coin door. Set the power on/off switch to the on position. Within approximately 30 seconds the TV monitor should display a picture. Slowly open the lower rear access panel. The TV monitor picture should disappear when the panel is opened approximately 2.5 cm (1 inch). Close and lock the lower rear access panel and repeat this step with the other access panel, acrylic attraction panel and the coin door. if the results of the previous step are satisfactory, the interlock switches are operating properly. If the TV monitor doesn’t go off as described, check to see if the corresponding in, terlock switch is broken from its mounting or stuck in the on position.

Page 13

¥ { VOLUME INCREASE: ‘ TURN CLOCKWISE Normally the only adjustments on the Missile Command™ game are option switch changes (made on the &toggle DIP switches). Uniess you are qualified technician, do not turn the ‘small knob on the Reguilator/Audio PCB. For information pertaining to this control, refer to schematic drawings OP-158-01 and 02,

OPTION SWITCHES {total of 16)

Figure 5 Location of Self-Test Switch,

Volume Control and Option Switches

E. Self-Test Procedure

This game will test itself and provide data to demonstrate that the game's circuitry and controls are operating properly. The data is provided on the TV monitor and the game speaker, no additional equipment is necessary.

Part of the self-test procedure includes a display of the operator-selectable game options. Therefore, we suggest you run the self-test procedure anytime you need to change the game's options. To fun the self-test, follow the instructions outlined in Figure 6.

F. Option Switch Settings

  • Bonus Play Feature Missile Command™ is the first Atari game to offer a bonus play for every $1.00 worth of coins inserted. This bonus feature is operator-selectable, meaning you may choose to offer it or not. With your game set at 50¢ per play and the bonus option on, players who deposit four successive quarters or a $1.00 coin, then press the start button, will receive a bonus play. Therefore, players receive 3 plays for $1.00. This bonus feature encourages players to insert more money than just the minimum 50¢ required for one game.
Page 14

Instruction

  • Set self-test switch to on position (see Figure 5). Note: entering self-test will set the HIGH SCORE TODAY display to 7500.

2 Roll the Trak Bail contrat in all directions.

  • Press the following switches: @ Coin switch trip wires @ Coin door siam switch @ Ail three fire switches @ Player start button

4, Set self-test switch to off Position. Figure 6 Self-Test Procedure

Result if Test Passes

After about 5 seconds of frozen attract mode, a low raspy tone is followed by alow beep, then high beep. TV monitor. screen displays picture as shown below: ROM OK . MAP OK as RAM OK + ..plus the options display—see Figure 7 for explanation. Both LED start buttons will also be lighted.

The + moves around on the screen in directions corresponding to Trak Ball control—up to an invisible border along the screen's edges.

A sound is heard as each switch is pressed, The background color also changes. \ Result if Test Fails

A continuous raspy tone means V BLANK is malfunctioning. Self-test will not continue. A RAM failure is indicated by a blank or “garbage”-filled screen and a repeated series of 8 beeps, separated by a low ~ raspy tone. See note 1 below. Seif-test will not restart,

ROM failure Is indicated by BAD ROM;

see note 2 below.

BAD MAP means bit-mapping hardware

has failed. BAD CHIP means custom audio 1/0 ohip at location P89 has failed.

The + doesn’t move in same direction as ball, or not at all. One of the Steering PCBs on Trak Bail control may be bad, harness _ wires or connector may be loose, Trak Ball reading circuitry on Game PCB may be bad, or Trak Bail bearings may need oiling.

No sound or color changes are produced when pressing one of these switches: indicates a bad switch, loose harness wires, or loose connector?

Note 1:

High beep in Bad chip series of 8 tones: at location: 1st Pa 2nd NS ord M4 4th 4 Sth Ka 6th J4 7th H4 8th Fa In test no. 1. a low beep means a good chip; a high beep is a bad RAM, as follows:

Note 2 BAD ROM plus some or all of the digits 1 thru 6 are displayed. These numbers show which 2K of memory are bad. For example, 1 means the a 2K are bad. The + may not appear.
Page 15

2. Coin Mechanism Multipliers

Since early in 1980, Atari has made available its new coin door which has either two or three mechanisms. All recent Atari game PCBs identify the different mechanisms in a certain pattem. :

The right coin mechs are all the same to the _ game's logic, regardless of whether you have two or three mechs in your door. In addition, the logic sees the left mech in a 2-mech door and the center mech in a 3-mech door as the same. Refer to the dlagram below. :

This pattern is important for you to know, so you can correctly set the “multipliers” for each mech. The multipilers determine how much each mechanism will be worth to the game’s logic.

The basic unit of measurement is 25¢, which equals a multipller of x1. Therefore, if you have a 25¢/25¢/$1 coin door, you will probably want to set the center and right option-switch multipliers at x 1x 4, (The left mech in a 3-mech door always has avalue of x 1—you cannot change its value.)

You can set these multipliers with toggles 3 thruS on the Missile Command PCB switch assembly at location R10. For exact settings of these toggles, refer to Figure 7 on the next page. *

  • Examples of Option Switch Settings . To explain the options, we have provided below four examples of the most common U.S. situations. The toggles mentioned below only relate to game price, coin mechanism multipliers, and the bonus credit for 4 successive quarters or the $1.00 coin. You should set the toggles relating to other functions as you see fit, although Figure 7 provides “$" signs indicating Atari's recommendations. ” At R10, set toggles— 5 4 For the first and second examples, we will assume your door (either 2 or 3 mechanisms) has only \25¢ slots:

If you want 50¢ (2 coins) for 1 play, and $1.00 for 3 plays: At R10, set toggles— - 5 4

ononononoft

At R8, set toggle 3 off.

If you want 50¢ (2 coins) for 1 play, and no bonus credit: :

ononononoff

At R8, set toggle 3 on.

For the third and fourth examples, we will assume your door (either 2 or 3 mechanisms) has a 25¢ mechanism at left and center, and $1.00 mechanism at right: If you want 50¢ (2 coins) for 1 play, and $1.00 for 3 plays: ‘ At R10, set toggles—

5421
ononoffonoff

At RB, set toggle 3 off.

If you want 50¢ (2 coins) for 1 play, and no bonus credit: At R10, set toggles—

5421
ononoffonoff

At R8, set toggle 3 on.

Page 16

Sit-Oown Missile Command™ Figure 7 Option Switch Settings To change toggle positions on the switch assembiles, you need not remove the game PCB. The switches, usually colored blue, are easily accessible when the game PCB Is mounted in place. When changing the options, verify proper results on the TV monitor display by performing the self-test. Note that changing an option on any toggle will cause an immediate change on the TV monitor screen during the self-test.

Toggle Settings of 8-Toggie Switch on Game PCB: (at R10) (RIGHT switch when PCB is in game)

87654321oeOption
On‘On1 coin® for 1 play

Off On Free play

OnOft2coins* fori play $
3OffOff, — 1 coin* for 2 plays
OnOnRight coin mech x 1$
3OnOttRight coin mech x 4
FdOttOnRight coin mech x 5
OttOttRight coin mech x 6:

On Center coin mech x 1 $ (Center mech is a left

-.OffCenter coin mech x 2mech in a 2mech door
OnOnEnglish language

On Ott French language

Off On German language

OffOff‘Spanish ijanguage

Toggle Settings of &-Toggie Switch on Game PCB (at A8) . (LEFT switch when PCS is in game)

87°654321Option
OttOttGame starts with 7 cities
OnOnGame starts with 6 cities$
Off,OnGame starts with 5 citles\
OnOff,Game starts with 4 cities\
  • On No bonus credit | = Off 1 bonus credit for 4 successive quarters or a $1 coin $ Ott Large Trak Ball input (switch must be off for proper
OffOttOn
OnOnOft

On Ott Olt Oft On Off

Off Off Off

The format of the self-test display is as follows:

Bonus city every points (line disappears if no bonus city is chosen) . + Coinage setting 4, 5, 8, of 7 cities (always in English) A 8 co

A is the center mech multiplier for Smech doors, left mech multiptier it a 2-mech door. This number is either 1 or 2, is the right coin mech multiplier and is 1, 4, 5, of 6. Cis an “F™ if switch 4 (of 8) is off. Dis an “X" if switch 3 (of R8) is off. operation of Sit-Oown Missile Command game) $ Bonus city every 8,000 points Bonus city every 10,000 points $ Bonus city every 12.000 points Bonus city every 14,000 points ‘Bonus city every 15,000 points Bonus city every 18.000 points Bonus city every 20,000 points No bonus city

An example of an actual option switch display is as follows:

BONUS CITY EVERY 10,000 POINTS + 2 COINS 1 PLAY 6 CITIES

11FX’

“In the U.S, 2 “coin” is defined as 25¢. If your game also has a $1 mechanism, you must set the right cain mechanism multiplier as per your choice. / $ Manuiacturer’s suggested settings . += This option available only if game PC3 nas 02 memory in- Stalled.

Page 17

G. Game Play

Sit-Down Missile Command™ is a 1-player game with a color monitor. The game depicts an Armageddon-style war in which a player defends bases and cities with antiballistic missiles (ABMs). The enemy—the game computer—launches incoming waves of attack missiles. These weapons may ba either individual or branching attack missiles. In addition, the enemy occasionally launches missiles from a fast-moving “killer” satellite or from bombers. The enemy also launches “smart” missiles that usually avoid explosions. Players receive varying numbers of points for intercepting attack missiles, for having unused missiles still in their bases’ arsenals, and for having their cities undamaged after a missile wave.

_ The game has five possible modes of operation: attract, ready-to-play, play, high-score initial, and self-test. The latter is a special mode for checking the game switches and computer functions. You may enter. this mode at any time. When entered, all” game credits are cancelled, and the “HIGH SCORE TODAY” is reset to 7500. A list of eight “highest” scores and Initials are also reset onto the screen (to provide player challenge).

  • Attract Mode The attract mode begins when power is applied to the game, after a play or high-score initial mode, or after self-test. This mode is continuous and is only interrupted when a game is paid for and accepted, or when entering self-test.

In this mode, the Missile Command name is displayed, then the computer plays one wave—handling both offense and defense. Following this, the computer displays the high score table, then the Missile Command graphics reappear.

  • Ready-to-Play Mode This mode begins when sufficient coins have been accepted for a one-player game. It ends when the 1 PLAYER START pushbutton is pressed.

When this mode begins, the message PRESS START scrolls along the bottom of the screen. DE- FEND CITIES and red arrows pointing down to each \ city also appear on the screen. The displayed pictures are otherwise the same as those shown in the attract mode.

3. Play Mode

The play mode begins when the start pushbutton is pressed. The mode ends when the player's last city is destroyed.

The three bases—Alpha, Delta and Omega—each have 10 ABMs ready to be fired (shown as A's). Players must be carefui to fire the missiles more or less evenly from among those bases, because no more missiles are granted until the screen resets In preparation for a new wave of attack missiles. If the enemy missiles strike a city or base, the colorful buildings or base will change to the. solid color of the landscape. .

The game continues until all cities ‘are destroyed. Missile Command™ has no operator-selectable fixed time length. Thus a highly skilled player can play longer than the novice. x: During the second wave, a “killer” safellite and/or bomber will appear on the screen, moving quickly and launching attack missiles at the bases and cities. Players get bonus points for shooting down the satellites or bombers.

The general approach for getting high point scores is fairly quickly discovered: try to launch your ABMs when the enemy missiles have just appeared at the top of the screen. Then they are clustered together, where one ABM can usually destroy several enemy missiles. In the later more advanced waves, players can lay out a blanket of explosions.

  • High Score Initial Mode \f a player's score exceeds the minimum on the high score initial list, he or she may put up to three initials on this list at the end of the game. Spinning the Trak Ball control changes the letters (A thru Z and a blank are available). Pressing any fire switch will fix that letter on the screen, and move the choice to the next letter. If the player doesn’t enter his or her initials within 90 seconds, three blank spaces will be entered automatically. om
Page 18

Maintenance

and Repair .

The Missile Command™ game requires certairr maintenance to keep it in good working order. Clean, properly maintained games attract players and earn more profits. The most important maintenance item is running the self-test every time you collect money from the cash box. Just looking at a game will not tell you if the Trak Ball™ control or light-emitting-diode switches are broken, or if LEDs have burned out. The self-test will inform you of any of these possible problems. * Second, you should regularly clean the outside of the game and the coin mechanisms, In addition, you will need to regularly lubricate the Trak Ball control: for details see this chapter.

y

Page 19

A. Cleaning —

The exterior of the game cabinet and the metal ., and acrylic surfaces may be cleaned with any nonabrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor. Do not dry-wipe any of the acrylic panels, because any dust can scratch the surface and result In fogging the plastic.

B. Fuse

Replacement

This game contains six fuses—all on the power supply assembly (not including the TV monitor fuses). Replace fuses only with the same type as listed in Figure 20 of this manual. See the color TV monitor manual, TM-148, for the monitor fuse data.

C. Opening the _ , Control Panel

Prior to replacing any switch or repairing the Trak Ball™ on the control panel, be sure to unplug the game. Then you will have to open the control panei as described below.

Using an Allen wrench, remove all three Allenhead screws along the top edge of the control panel (see Figure 8). Lift up on the control panel and tilt it towards you. Now the LED switches and the Trak Ball control are accessible for servicing.

TRAK BALL CONTROL

LED. SWITCH: TO REMOVE TURN COUNTERCLOCKWISE

NORMALLY CLOSED (N.C) CONTACT

NORMALLY OPEN — (N.0) CONTACT

LIGHT-EMITTING —~ DIODE (LED) CONTACTS COMMON _ CONTACT

Figure 8 Opening the Control Panel

Page 20

Disassemble in the order indicated. (Cireied numbers match the steps described below.) .

Ball Replacement 4, Remove the entire Trak Sall assembly as shown in the previous figure. Locate the three countersunk machine screws in the acrylic top plate; remove these screws. (When the assembly is installed, these three screws are fight undemeath ihe control panel). 2 Remove and replace the ball.

Steering PCB Replacement 3 Remove the hardware holding down the black y toathed wheel (the light hub} lilt this wheel off Sf of the black roller shaft. Unplug the connector on the steering PCB. Remove the two cross-recessed machine screws, brown spacers and lock nuts from the steering PCB. 4 Remove the steering PCB. 5, When replacing this PCB assembly, be certain that the black toothed wheel tums freely between the two halves ot the red photosensor device, LUBRICATETHIS BEARING (1 OF 5 PLACES) a™ Sit-Down Missile Commant

{

Trak Bail Lubrication a

  • Open controt panel as illustrated in Figure & 2 Unplug the control panel hamess connector. 2 Apply only 2 drops of 3-in-One? oil in each of the ball bearings. (Each Trak Ball control has five bearings) Tilt the panel to its closed position and roll the ball in all directions. Be sure the oil has not spread onto the shafts—otherwise your players will get oily hands.

Figure 9 Trak Ball™ Maintenance and Repair

  • LED Switch Replacement The light-emitting diode (LED) switches on the control panel have a very low failure rate. In case a switch should ever be suspect, first test it per the description that fotlows. To replace the switch, refer to Figure 8.

@ Remove the wires from the suspected switch. @ Set multimeter to the ohms scale, Set ohms scale to Rx 1, then zero the meter. @ Connect muitimeter leads to appropriate LED switch contacts (see Figure 8 for designation of switch contacts).

@ Check contacts (push and release the switch

button) for closed and open continuity. @ ifthe contacts do not operate sharply or always remain closed or open, then replace the LED switch as outlined in the figure.

  • Trak Ball™ Maintenance and Repair - To maintain this control, you will only have to lubricate the bearings approximately every 2,000 credits. The number of credits can be read off the coin counter, located on the coin door. Use only 2 drops of 3-in-One® oil in each of the bail bearings. (The Trak Ball control has five bearings.) For further instructions on how to replace thé Trak Bail or either Steering PC, see Figure 9,
Page 21

D. TV Monitor

Removal

CAUTION High voltages may exist in any television unit, even with power disconnected. Use extreme caution and do not touch electrical parts or the TV yoke area with your hands or with metal objects in your . hands! In addition, be sure to use heavy gloves . when handling the monitor. You could cut your hands on the metal TV chassis, with- . out such protection.
  • Uniock and remove the front access panel and the rear acryiie attraction panel as shown, 2 Olsconnect the TV monitor hamess at left side of front cabinet opening. ‘Carefully bend and lift up the front fap of cardboard monitor bezel. Remove the staples on each side. and lift out the bezel, 4, Remove 2 screws that secure each front monitor bracket to cabinet, Then remove both bolts that attach the brackets to ‘the monitor frame. Set the brackets and their hardware aside. At rear opening, remove 2 bolts that hold the wood monitor mounting board In the cabinet. The monitor will now tilt for: ward onto its face and rest against the diagonal wood tracks: in the cabinet, & Raise the monitor and its wood shelf over (he stops onto the tracks, One person should brace the front of the monitor on each side. . La Eaze ne monitor up the track wt you have tted up about &: Slide the monitor up and out of the cabinet. Installation Is the reverse of this procedure. If you should need to service or replace the color. TV monitor, you must first remove it from the game cabinet. Follow the instructions given in Figure 10.
Note that two people are required to remove the monitor assembly—it weighs about 80 pounds! In addition, Atari recommends you use a small step stool to stand on. while tliting the monitor upwards. However, if you are about 6% feet tall, you could probably remove the monitor without this stool.

Figure 10 TV Monitor Removal

Page 22

REGULATORE AUDIO PCB *

Figure 11 MISSILE COMMAND Sf GAME PCB ’

Game and Regulator/Audio PCB Replacement

E. Printed-Circuit Board Replacement

You may wish to remove the game printed-circuit board (PCB) or the Regulator/Audio PCB for service or inspection. To do this, refer to Figure 11 and proceed as follows:

  • Game PCB Removal @ ‘Unlock and open the lower rear access panel. @ Remove the two beaded tie wraps and then the . 44pin edge connector from the right side of the game PCB. @ Locate the Philllps-head screw that extends through the PC8 and into the wood block near the game's cpening. Remove this screw. @ Remove the PC8 from the game by sliding it out of the plastic PCB retainer. N eee Reinstall the PCB, making sure that the 44-pin edge connector is properly plugged in. Note that the connector is keyed to fit on only one way, So if it doesn’t slip on easily, don’t force it! A reversed connector will probably damage your game and will void the warranty. Check that the operation of the game is correct by performing the self-test. This is especially

important with any game when you replace a

PCB. Regulator/Audio i ll PCB Removal Unlock and open the access panel. Remove the five plug-in connectors. Locate the two Phillips-head ‘screws that extend through the PC8 and into the wood blocks

Remove the five plug-in connectors at the top two corners of the PCB. alla

these two screws, Remove the PCB from the inside wall of thé” cabinet by pulling it up and out of the wood slot.

Page 23

Sit-Down Missile Commana™

F. Opening the . Attraction Panel

Prior to replacing the fluorescent tube or the speaker, you will first have to remove the graphics attraction panel at the top rear of the Sit-Down Missile Command™ game. -

Unplug the game; then remove the three Allenhead screws at the top of the panel. They secure the metal retainer strip for the attraction panel. Remove the retainer completely. Now remove the two Phillips screws located on the sides of the panel. Tilt the top of the %4-inch attraction panet towards you, then lift it up and out of the bottom wood retainer (see Figure 12).

Behind it you will find a smaller, 1/8-inch smokecolor window panel: this can remain In place while you service the fluorescent tube or speaker.

  • Replacing Fluorescent Tube
  • WARNING tf you drop a fluorescent tube and it breaks, it will Implode! Shattered glass can fly 6 feet or more from the implosion. Use care when replacing any fluorescent tube. First remove the colorful attraction panei as previously described. Then replace the white fluorescent tube by following this procedure (see Figure 12). _

@ Remove the two Y-shaped connectors from the ends of the fluorescent tube. Now carefully remove the tube from its clamps by pulling it towards you. @ Replace with a new tube. Do not snap the tube in vigorously—you may break it, causing an implosion! @ Close up the game by replacing the attraction panel, retainer strip, and three Ailen-head screws,

  • Replacing Speaker First disconnect the harness plugs for the speaker. Remove the four screws that secure the speaker on the wood panel. Replace the speaker, then reconnect the harness connectors. 4

Never operate the game without the metal shield located just above the speaker the shield prevents the speaker's magnetism from adversely affecting the monitor's color purity.

Figure 12 Fluorescent Tube and Speaker Replacement SECURING SCREW ‘ RETAINER STRIP

FLUORESCENT LIGHT ASSEMBLY g \

7 ATTRACTION + PANEL

Page 24

G. Game Operation

With this manual you received two large sheets that contain the wiring and schematic diagrams for your game. Sheet 1, Side A, includes information that shows the arrangement of these diagrams. These diagrams include information that explains the functions of the circuits and defines inputs and outputs.

, Missile Command™ is a microprocessor-controlled game. The microprocessor is mounted on the game PCB. The game PCB receives switch inputs from the control panel and coin door. These inputs are processed by the game PCB and output to the TV monitor, Regulator/Audio Ii PCB, loudspeaker, and control panel. The Regulator/Audio !! PCB performs two functlons: 1) it regulates the +10 VDC from the power supply to +5 VDC, and 2) it amplifies the audio output from the game PCB. The +5 VDC from the Regulator/Audio Il PCB provides most logic power to the game PCB. The audio output from the Regulator/Audio Il PCB directly drives the game speaker and is controlled by the volume control, mounted Inside the coin door.

The Power Supply is the source of all voltages In the game. These voltages are protected by three fuses (F3, F4 and F5) on the power supply chassis. The primary winding of the power supply transformer is protected by the fuses F1 and F2 on the power supply chassis.

Figure 13 illustrates the distribution of power In this game. Figure 14 illustrates the distribution of signals. :

Page 25

POWER INTERLOCK SWITCHES

"FLUORESCENT LAMP

COLOR MONITOR -

AC POWER CORD

a

POWER ON/OFF SWITCH

GAME PCB

REGULATOR/AUDIO Il PCB

POWER INTERLOCK

SWITCHES POWER SUPPLY

COIN DOOR

a Figure 13 Power Distribution

Page 26

Sit-Oown Missile Command™

CONTROL PANEL

| REGULATOR AUDIO PCB

A 3 g |

ga) BEES

  • “AE

VA COIN DOOR

. VOLUME CONTROL ’

e0 - Figure 14 Signal Distribution

Page 27

Illustrated

Parts Lists

The purpose of this chapter is to provide you with the necessary information for ordering replacement parts for your Atari Sit-Down Missile Command™ game. Please note that, for simplicity, common hardware has been deleted from most of these parts lists. This includes screws, nuts, washers, bolts, ete. N ‘ The parts lists have been arranged in alphanumeric order. For example, all “A-" prefix numbers come first. Following this are numbers in sequence evaluated up to the hyphen, namely 00- thru 99-, then 000598- thru approximately 110000-.

When ordering parts from your distributor, give the part number, part name, applicable figure _ fumber of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be fess downtime and more profit from your game.

Sit-Oown Missile Command™

Page 28

Sit-Cown Missile Command™

e@ : A036189-01 Bn (Intert, Sw Brkt) Fluorescent Lt. Assy.— A036538-01

  • 034648-01 see Figure 19 A036460-01
(25-inch Color Mon.)nield Retainer.(TopHi:
{ShieldRetainer)oaaearnn(TopHarness)

03491301 & 02 (etanen) (Front Monitor Brits.) 036537-01 [7 =< Om (Attraction Panel) 09652001 — : ;

(Monitor Bezel).aS BN001838.01
dX-eea“(Rear Mon. Bracket)

A036503-01 ‘ heheh (Mirror & Panel) Speaker)

038542.01 . (Wincew Panel) 036536-01

Trak Ball Assy.— {Monitor Shield)

: see Figure 17

Control Panel Assy.— RegJAudio tt PCB— see Figure 16 - . see Figure 21

A034631-01 \

r )(OnOlf SwchLSVe@

00999201 7 Game PCB— see Figure 22 ‘OnOft Sw Cover)

034536-03 (Foam Oamper) 035745-02 A036849-01 thru 03 (PCB Retainer) (Power Cord) 5

71-2114 78-3201 Coin Door-< (Lock) Leg) see Figure 23

00788202 A036457-01 (Intert. Sw. Cover) Main Harness)

A030169-02cssssrav| !.

19-9032 (Vol. CinlBrkt) (Fan Griliey Fi v--\) ‘Not. Control) Power Supply— . A021700-01 thes 03 see: Figure 20 . (Con Box) rte oh NOTICE TO ALL PERSONS RECEIVING THIS ORAWING

030249-01(Fan)CONFIOENTIAL: Ae*ine

_ Soecihie wentten dermission of Atan, Inc., Sunnyeale. CA, :

(Coin Box Seoarator).Hy concutonally adued. and, nertner

‘auoject matter of ihe draw raion shown thereon,

inaer lense. no night to reoroduce tnrs arawing 18 granted oF the subject matter thereat unt written agreement with oF written permission Irom tne coroaration. ; Figure 15 Cabinet-Mounted Assemblies

r ):A036530-xxB
Page 29

Figure 15 Cabinet-Mounted Assemblies - — Parts List

Part No. Description

A005133-01Exhaust Fan.

02170001 Coin Box Assembly (for all the same coins) 1700-02 Coin Box Assembly (for two different coin denominatlons—has one separator) A021700-03 Coin Box Assembly (for three different coin denominations—has two separators) A030169-02 Volume Control & Bracket Assembly A034631-01 On/Off Switch Assembly A036189-01 Interlock Switch & Bracket Assembly (modified for safety) 03645701 Main Harness and Components Assembly (Includes lower two interlock switches and onloft : switch) A036460-01 Top Harness and Components Assembly (includes top two interlock switches) Monitor Hamess and AC Cord Assembly Mirror/Panel Assembly 25-Inch Electrohome Color Monitor Assembly A036549-01 Strain-Relief Power Cord (domestic) OR A036549-02 Strain-Retief Power Cord (German) OR A036549-03 Strain-Rellet Power Cord (Australian) OP-1$8.01 Sit-Down Missile Command™ Schematic Drawings, Sheet 1 OP-158.02 Sit-Oown Missile Command Schematic Orawings, Sheet2 . TM-162 Sit-Down Missile Command Operation, Maintenance, Service Manual TM-163 Service Manual for Electrohome 25-inch Color Monitor

19-9032Volume Control Potentiometer. \ .
48-009Inch 8-Ohm 8-Watt High-Fidelity Speaker¥

71-2114 Panel Cartridge Lock Mechanism (for access panels)

7507017Spacer for Mounting Printed-Circuit Boards(two per screw)

78-24012 SInch Beaded Nylon Tie Wrap (for securing edge connector to Game PC8) 78-3201 Cabinet-Leveling Leg 000869-01 SInch Ventilation Grille 001638-01 Rear Monitor Mounting Bracket 005419-01 &-Inch Speaker Grille 006870-01 Coin Box Bracket

00788202Interlock Switch Cover.

00999201 On/Off Switch Cover 030249-01 Coin Box Separator 034536-03 Foam Vibration Damper 034537-01 Fan Grille - 034647-01 Attraction-Panel Retainer (at top rear of game) 03464801 Monitor-Shield Retainer 034913-01 Front Monitor Support Bracket—Left Side (as seen facing front of game where power cord exits) 03491302 Front Monitor Support Bracket—Right Side - 03574502 18-Inch Plastic PCB Retainer .

036515-01Graphics Label for Consolea

036520-01 Cardboard Bezel (for monitor) 03652101 Cover Plate for Power-Cord Hole 036536-01 Smoke-Color Monitor Shield 096837.01 Graphics Attraction Panel — / 93654201 Smoke-Color Window Panel °

Page 30

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without . \ the specific written permission of Atar. Inc. 2 Sunnyale. GA. This drawing is only conditionally issued, and neither receipt nor possession thereat conters of transfers any fight in. of licerse to.use, the subject matter of te drawing of any design oF . technical information shown thereon. nor" any Hint to eoroauce ins drawing or any part thereat, Except for manufacture by vendors of Atari, Inc. and for manufacture under the cor "s write ten license, no right to reproduce this drawing is Granted ar the Subject matter thereof unless by Written agreement with of written permission from the corporation, 033127-01

Trak Bail Assy.— See Figure 17

Figure 16 Control Panel Assembly A036523-01 B

Parts List

. Part No. Description

. A036458-01 - Control-Panel Hamess Assembly

  • 62-039 SPOT Momentary Pushbutton Switch, with Red Cap and Light-Emitting-Diode + 62.041 SPOT Black Momentary Pushbutten Switch 75-07054 Nylon Spacer . 75-9910W0 Steel Stamped Nut -033127-01 ~~. Black Moided Switch Bushing rs) 026535-01 Metal Control Panel with Graphics
Page 31

Figure 17 Trak Ball™ A033360-01 Assembly - G Steering PCB Assy.—

See Figure 18

75-980504C 74-A00011 \

Page 32

Figure 17 Trak Ball™ Assembly Parts List :

Part No. Description

72-1006S #10-32 x 38° Cross-Recessed Pan-head Cadmium-Plated Steel Machine Screw 72-1408S #440 x 1%" Cross-Recessed Pan-Head Cadmium-Plated Steel Machine Screw 72-1606S #6-32 x W8* Cross-Recessed Pan-Head Cadmium-Plated Steel Machine Screw 72-8808 #8-32 x ¥2” Hex Socket-Head Cap Alloy Steel Machine Screw 72-8920S 438-16 x 1%" Hex Socket-Head Cap Alloy Stee! Machine Screw 73-3006 Carbon Spring Steel External Retaining Ring, for 8" shaft diameter 74-A00011 Phenolic Spacer, 1/8” Insida diameter x %” outside diameter x Y%" long 75-010S, #10 Flat Plain SAE-Standard Zinc-Plated Steel Washer 75.0168 #6 Flat Plain SAE-Standard Zinc-Plated Stee! Washer 75-018S #8 Flat SAE-Standard Zinc-Plated Stee! Washer 75-040S #10 Steel Split Lock Washer 75-041S #3/8 Steel Split Lock Washer 75046S #6 Zinc-Plated Steel Split Lock Washer 75.048S #8 Zinc-Plated Steel Split Lock Washer \ 75-3608S, #6-32 x ¥2” Cross-Recessed Flat-Head Cadmium-Plated Steel Machine Screw 75-916S #6-32 Standard Cadmium-Plated Steel Machine Hex Nut 75-9198 #46-16 Standard Cadmium-Plated Steel Machine Hex Nut . 75-990504C, #4-40 Shallow-Pattern Prevailing-Torque Corrosion Resistant Lock Nut \ 85-1808B #8-32 x ¥2” Socket Cap Flat Countersunk-Head Black-Oxide Stee! Screw _ Y. 00061601 Light Hub 033355-01 Base Plate 1 Top Plate 033357-01 Cover Plate (Acrylic) 933358-01 Corner Post 033359-01 End Post 033361-01 Steering PCB Bracket 033362-01 Roller Shaft 033363-01 Cylindrical Post 033364-01 Adjustable Post 033365-01 Spacer 033366-01 Trak Ball™ : 033367-01 Bearing 03416801 Label with Lubrication Instructions

/

Page 33

030269-01

a a Q 2 ~

w wi od 7

Traces shown are on opposite side.

ev IRATAQ °

\emarg € 79-58005 CSnEGENtiat Sauocuenen “oncden sasout ine 5 ae Sunnyvale. CA

faming sa yranted oF Rereo! uniess oy artien ayreement wuts or ation on fram ihe sorgoratior

Figure 18 Steering Printed-Circuit Board Assembly A0Q09060-02 c

Parts List

Part No. Description (Reference Cesignations and Locations in Sold)

40-5331 33¢ Ohm. = 5%, %W Carbon Composition Resistor (R10-13) 10-5392 3.3K Ohm, = 5%, vW Carbon Composition Resistor (A14, 15) 4 10-5471 470 Ohm, =5%, «W Carbon Composition Resistor (R7-8) 27-250104 0.1 uf, = 20%, 25V Ceramic-Disk Radial-Lead Capacitor (C2) 29-046 10 uf, = 10%, 2GV Tantalum Axial-Lead Capacitor (C1) 24-2N0643 Type 2N3643 Switching Transistor (Q1, 2 30-Contact Connector Radial Cotical Coupler

Page 34

NOTICE TO ALL PERSONS RECEIVING THIS ORAWING ‘TIAL: Reproduction torbidaen without the

Figure 19 Fluorescent Light Assembly A036528-01 A Parts List

Part No. Description

A005493-01 Fluorescent Light Harness Assembly

70-301 24-inch 20-Watt Cool White Fluorescent Tube 79-561816P. Wire Nut for 16- to 18-Guage Wires . + 99-11003 Fluorescent Lamp Starter 99-11008 Sallast Transformer 99-11009 Starter Socket : - 99-11011 1¥2-Inch Clamp | 035835-01 Y-Lead Connector (two required per light). Alternate is part no. A036045-01 .

Page 35

: 79-4411008 eas 46-2017002 osasag.or —-48-2018002

TOP VIEW 78-2708

29-053 * NOTICE TO ALL PERSONS RECEIVING THIS, GONFIOENTIAL: Reproduction forbidden without the specific written permission of Aten, Ine, Sunnyvale, GA. This crewing 18 only conditionally issued, and neither receipt nos possession thereat cantera of transiars any night in, oricanae to use the suoject maiter of tne drawing or any design oF technical information shown thereon, nor Inght to reproduce this drawing or any part thereor Excent for manufacture by. vendors of Atan, Inc, and for manufacture uncer. the corporation's wrt: ten license. no nght to reproduce ths drawing 18 Granted of the suoject matter tnereo! unless Dy . ‘watten agreement with of written permiaaion fromm 42-7140 the comporation.

y

BOTTOM VIEW

A034629-01

Figure 20 Power Supply Assembly for Raster-Scan Games ‘ e : ; A034560-02 D

Page 36

Figure 20 Power Supply Assembly for Raster-Scan Games Parts List y-\)

Part No. Description

A006555-01 Rectifler Printed-Circuit Board Assembly A034623-61 Transformer and Harness Assembly (includes Power Transformer)

A034629-01AC Harness Assembly+
A034630-01FI Filter Assembly:...

A035674-01 Voltage Plug Assembly (set of four plugs) 26,000 uf 15V Electrolytic Capacitor

42-7140Power Transformer Onlyid

46-2013002 3-Amp. 250V 3AG Slow-Blow Glass Cartridge-Type Fuse 46-2017002 7-Amp. 250V 3AG Slow-Blow Glass Cartridge-Type Fuse 78-2708 Nylon Type &/6 Hole Bushing with 5/8” Inside Diameter x 55/64” Outside Diameter x Ye" Thick 78-70501SC 2”-Diameter Capacitor Mounting Bracket 79-15021001 2-Circuit Single-Row Terminal Block 79-3206 5-Position 3AG Fuse Block with 4" Quick-Disconnect Terminals

79-4411006Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post.

034544-01 Fuse Block Cover

Page 37

Sit-Down Missile Command™ . i

NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL: Reproduction forbidden without the specific wetten permission of Atari, Inc. Sunnyvale, GA. This drawing is only conditignalty issued, and neither receipt nor possession thereat confers of transfers any ght in, of lice the subject maiter of ine drawing or ar technical infermation ‘shown ‘hereon. nor” any fight to reproduce this drawing of any part thereat. Except for manulacture by vendors af Alan, Ine, gx ind for manufacture uncer tne corporation's wet 4 ‘en license. no ight ta reproduce this drawing 18 33} Granted of the subject mattar thereat uniesa by Sa Aintten agreement with or written permission (rom 3a the corporation. fu : ag ez R>

m

Figure 21 Regulator/Audio Il PCB Assembly A035435-02 B

Page 38

Sit-Oown Missile Comman:

Figure 21. Regulator/Audio Il PCB Assembly a™

Parts List

Part No. Description (Reference Designations and Locations in Bold)

12-52P7 2.7 Ohm, + 5%, 1W Resistor (R5) 16-54P0 4 Ohm, + 5%, 5W Wirewound Resistor (R25) 19-100P 1015, .10hm, + 3%, 7W Wirewound Resistor (R24) 19-315102 1K Ohm Vertical PC8-Mounting Cermet Trimpot (R8) 24-250106 10 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (CS, 15) 24-250108 1000 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C9, 10, 13) 24-250477 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor {C1, 4, 12) 24-250478 4700 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C29) 24250108 1000 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C13) 24-250477 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C1, 4, 12)

. 24-35022622 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor(C24, 31)

24-350338 - 3300 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor (C9, 10, 18, 19)

24-500105,1 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor(C22, 23)

27-250102 .001 uf Ceramic-Disc 35V Radial-Lead Capacitor (C2, 7, 16) 27-250103 .01 uf Ceramic-Disc 25V Radial-Lead Capacitor (C5, C14) 29-088" .1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C3, 11, 20, 21) 31-A14F SOV 2.5A Miniature Axial-Lead High-Current Rectifier (CR1, 4-8)

33-TIP32PNP Power Transistor, Type TIP32(Q2):
”342N3055NPN Silicon Transistor, Type 2N3055(Q3)~~
37-LM305SV Linear Voltage Regulator (Q1)4
37-7812+12V Voltage Regulator, Type 7812(Q8)\
37-7905-5V Voltage Regulator, Type 7905 (Q9):*,

72-1608C. #6-32 x 2" Cross-Recessed Pan-Head Corrosion-Resistant Steel Machine Screw 75-F60405 #6-32 x %" Binder-Head Nylon Screw 7§-99516 . #6-32 Nut/Washer Assembly

78-16008,Thermally Conductive Compound(Q3)
78-16014Thermally Conductive Compound(Q2, 5, 7-9)
79-§83086-Position Connector Receptacle(J6, 9)
79-583089-Position Connector Receptacle(J7)
79-5834612-Position Connector Receptacle(J10)
79-583544-Position Connector Receptacie(J8)

020670-01 Test Point : 034§31-01 Heat Sink

110000-0101 Ohm, + 5%, %W Resistor(R10, 19)
110000-10010 Ohm, + 5%, %W Resistor(R11, 20, 29, 30)
110000-101100 Ohm, + 5%, %W Resistor(R4, 12, 22)
110000-1021K Ohm, + 5%, %W Resistor(R27, 28)
110000-10310K Ohm, + 5%, %W Resistor(R13, 14)

110000-271 270 Ohm, + 5%, %W Resistor (Ri) 110000-330 33 Ohm, + 5%, %W Resistor (R3)

110000-3923.9K Ohm, + 5%, %W Resistor(R6)

110000-562 5.6K Ohm, + 5%, %W Resistor (R32, 33)

110000-7527.5K Ohm, + 5%, %W Resistor (R7)r*

110001-221 220 Ohm, + 5%, Y2W Resistor (R9, 21) 116000-220 22 Ohm, + 5%, 10W Wirewound Resistor (R31) 122004-224 .22 uf Ceramic-Disc 25V Capacitor (C6, 8, 15, 17)

137151002Type TDA2002A 8W Linear Audio Amplifier Intecrated Circuit(Q5, 7)/
Page 39

str peran Zosversned -cz ceivtere faow.

3 1 i / —

=" = J a = Ea LC no

on <q as of a3 £ £& or Oo? id o T+ w oO ; E eo 4 ; ‘ t { 5 r<¢ ou 2 i ANE —— * a . 2 (ey) ageu. 1) Ca E sav vs sey vs " ©) Gide

£ NOTICE TO ALL PERSONS RECEIVING THIS DRAWING

o CONFIDENTIAL Heprortuctiun torbitten Tt Mee 2 (2708 ENABLE specitie writion pecmssion of Atay, lnc , Sa = Ps . Tes dleawing 1s only conditionally rasveed, ae 2 fectunt hen powsrvaon tment contra or Wana 3 Bato Bus a _— BY6E ENABLE sulyect imatier 2 SPLIT PAD COMMECHONS. AS OETANFD ASE x DETAIL RPOLICAPLE 1 SE OF O3IGE'S.USE Or £708 S ‘Alant, We.

prquSee bmocie OF ort PALS. AND’ CUM es 3

iene, no tight to erp ig pai

ne fy mitten agreement ie Of COMMECTED PADS. tesa oe, atenten fer SCALE: NONE

Sait of writing persion front fhe corporation

Page 40

Figure 22 Game PCB Assembly Sit-Down Missile Comman: a™

Parts List \

Part No. Description (Reference Designations and Locations in Bold) C012294-01 Audio VO N-Channel MOS/LSI Custom Chip (P8/9) 21-101683, .068 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C65-68) 24-250105 1 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C76-79, 98, 100-104) 24-250106 10 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C20, 23, 39) 24-250107 100 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C9, 10, 46, $7, 91) 24-250226 22 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C90) 27-250103 .01 uf Ceramic-Disc 25V Radial-Lead Capacitor (C76-79) . 28-101102 1000 pf Epoxy-Dipped 100V Radial-Lead Mica Capacitor (C99, 105) 29-088 -1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C1-8, 13-16, 18, 19, 21, 22, 30, 38, 43-45, 47-56, . 58-64, 69-75, 80-89, 92-97, 106) 31-1N914 75V Type-1N914 Switching Diode (CR2) 34-2N3643, Type 2N3643 NPN Switching Transistor (Q8) (34-2N6044 Type 2N6044 NPN Darlington Transistor (Q1-3)

3745848Type 14584 Integrated Circuit(C9, C11)
37-7400Type 7400 Integrated Circuit(C5, 08)
37-74S00Type 74800 Integrated Circuit(A8)
37-7404Type 7404 Integrated Circuit(E6, K7)
7-7 404Type 74HO04 Integrated Circuit(B6)
37-74804Type 74S04 Integrated Circuit(D7)7
‘37-7407Type 7407 Integrated Circuit (N11)\
37-74LS08Type 74LS08 Integrated Circuit(H7)‘
37-7408Type 7408 Integrated Circuit(R2, J6)
37-74S08Type 74S08 Integrated Circuit(M3)
37-74LS10Type 74LS10 Integrated Circuit(E3)
37-7410Type 7410 Integrated Circuit(B5)
37-74LS14Type 74LS14 Integrated Circuit(D3)
37-7414Type 7414 Integrated Circuit(J9)

37-7427 Type 7427 Integrated Circuit (B7) 37-7432 Type 7432 Integrated Circuit (C3, R5) 97-74LS32 Type 74LS32 Integrated Circuit (J7)

37-74S32Type 74S32 Integrated Circuit(C4, L5, K6)
37-7442Type 7442 Integrated Circuit(N2, £8)
37-7474Type 7474 Integrated Circuit(H6, A7, £7, F7, J8, A9)
37-74S74Type 74S74 Integrated Circuit(A6, B8, C8)
37-7475Type 7475 Integrated Circuit(R7)
37-7493Type 7493 Integrated Circuit(04)
37-74109Type 74109 Integrated Circuit(06)
37-74125Type 74125 Integrated Circuit(R6)
37-74L$139Type 74LS139 Integrated Circuit(P2, M5)
37-74LS153Type 74LS153 Integrated Circuit(F5, H5, J5, KS, P7)
37-74153Type 74153 Integrated Circuit(F3, H3, J3, K3),
37-74LS157Type 74LS157 Integrated Circuit(H2, J2, K2, L2, M2, M7, D9)
37-74S$157Type 74S157 Integrated Circuit(E4)

37-74160 Type 74160 Integrated Circuit (E5)

Page 41

Sit-Bown Missile Command™ @ Figure 22 Game PCB Assembly, continued Parts List \

Part No. Description (Reference Designations and Lacations in Bold) 7

97-74163 Type 74163 Integrated Circuit (D5)

37-74LS 163AType 74LS183A Integrated Circuit(R4)
37-74LS168Type 74LS166 integrated Circuit(P6)

37-74175 Type 74175 Integrated Circuit (L8)

37-74LS175,Type 741$175 integrated Circuit(C7)

37-74LS191 Type 74LS191 Integrated Circuit (K8, K9) 37-74191 Type 74191 Integrated Circuit (A4, 84) 37-74LS195 Type 74LS195 Integrated Circuit (M6, N7) 97-74LS$244 Type 74LS244 Integrated Circuit (A/B1, E2, F2, PS, L9, M9, P10, 8/C1, NIP3)

37-74LS251Type 74LS251 Integrated Circuit(N5)

37-74S260 Type 748260 integrated Circuit (A5)

37-74LS273Type 74LS273 Integrated Circuit(N6, FS)
37-LM324Type LM324 Integrated Circuit(N10)

38-MV5053 Type MVSG53 Light-Emitting Diode (CR1)

62-007SPST Pushbutton Switch(B83)

66-118P iT 8-Station Single-Throw, Dual-inline-Package Bit Switch (R8, R10) 79-42C24 . 24-Contact Mediurp-Insertion-Force Integrated Circuit Socket (For -01 and 03 PCB Assemblies: | D1, &1, F1, H1, J/K1, K/L1, M1, MINI, N/P1, R1, R3; For 02 and -04¢ PCB Assemblies: H1, J/K1, 4 K/L1, UM1, NIP1. R1)

79-42C4040-Contact Medium-insertion-Force Integrated Circuit Socket(C2, P8/9). N
81-4302Nylon Snap-in Fastener\
90-12310.000 MHz, + .005%, Crystal(¥1)

90-6013 : Microprocessor (C2 .

90-7005Random-Access Memory(L7)

02067001 Test Point 035826-01 Programmable Read-Only Memory (L6)

100017-001Random-Access Memory(F4, H4, J4, K4, L4, M4, N4, Pa)

110000-102, 1K Ohm, =5%, %W Resistor (R1, 2, 4, 13, 16, 21-26, 39, 60, 61, 73, 74, 85, 95, 109-122) “110000-103 10K Ohm, =5%, %W Resistor (R3, 17-20, 30-38, 60-71, 83, 84, 86-88, 93, 94, 96-100)

110000-1521.5K Ohm, =5%, %W Resistor(R79)

110000-220 22 Ohm, =5%, %W Resistor (R46, 47, 82) 110000-221 220 Ohm, =5%, “W Resistor (R72) 110000-222 22K Ohm, £5%, %W Resistor (R76) 110000-332, 3.3K Ohm, +5%, %4W Resistor (RS56-59, 89-92) 110000-270 27 Ohm, =5%, %W Resistor (R5-12, 27-29) 110000-331 330-Ohm, =5%, %W Resistor (R14, 15, 78)

110000-391390 Ohm, =5%, %W Resistor(R45, 81)
110000-471470 Ohm, =5%, %W Resistor(R40-44, 48-55, 80)

110000-472 4.7K Ohm, +5%, “@W Resistor (R75)

110000-6826.8K Ohm, 25%, “4W Resistor(R101-108)
110000-8228.2K Ohm, = 5%, ‘%«W Resistor (R77)*

122004-224 .22 ut Ceramic-Disc 25V Radial-Lead Capacitor (C24-29, 31-37, 40-42)

137002-001Type 74S86 Integrated Circuit(L3)
137149-001Type 74LS11 Integrated Circuit(Fé, N3)

For remaining memory components and their part numbers, see list on next page.

Page 42

Sit-Cown Missile Coinmand™

Figure 22 Game PCB Assembly, continued Parts List

Memory Components and Their Equivalents (Locations Shown in Bold)

01 P.C. Boards02 P.C. Boards03 P.C, Boards04 PC, Boards
(mostly PROMs).(ROMs)(mostly PROMs)(ROMs)

09881201 KL1 03881202 KJL1 03582201 KILI 03582202 K/Lt 035813-01 F1 03581302 F1

03582301 LUMI* 038823-01 UMI -038623.02 UM1“036823.02 UM1
03581601 NIP103561602 NPI\
:035824.01 NIP103582402 NIP1
09881701 M/N403581702 MINI:

038818-01 RI 03581802 RI 035825-01 AY 03882502 Rt 035819.01 AS 03581902 RI

035808.01 H1 03580802 H1

.03682001 H103882002 H1

03580901 D1 038809-02 Ot

03581001 IK1 ~ ; 03581002 J/K1

03882101 JiK1.03582102 JK1

035811-01 Et 03561102 Et

,

  • /
Page 43

99-10095

99-10041

99-10081 COIN MECHANISM SEE PARTS LIST 1-120) 75-944 ( 99-10102 : H . 7172-96038 COIN RETURN: 9910085 SWITCH WIRE CHUTE | 99-10068 SEE PARTS LIST 99-1047 . 10078) © aniNsone q- COIN SWITCH ASSY. PART OF 99-1047 SEE PARTS UIST Sssone . 9.10082 1 thu 5. 99-10045) 78-1412

Figure 23. New Coin Door ~ / T110xxxx B . €

Page 44

~ Sit-Down Missile Command™

COIN RETURN BUTTON COVER— . \ SEE PARTS LIST (99-10055 thru 99-10059)

COIN RETURN BUTTON ASSY.— PRICE PLATE— SEE PARTS LIST SEE PARTS LIST (99-10012 thru 99-10022, (99-10070, 99-10083 99-10074 and 99-10107) ‘thru 99-10092, and 99-10108) 72-4A14058 COIN DOOR ONLY— ~ SEE PARTS LIST 99-10062 99-10 (99-10009 and 10010) ans

72-HA1404C

99-10081 NOTICE TO ALL PERSONS RECEIVING THis,

99-10066 om ts feoroguce tea otawing orany part Exesot for manufacture By vendors of Atar and for manutacture torepreck sore not nt en ticense, ne night to reproduce ms drawing Gfanteg or ihe subject matter inerect uniessroy —_75-918S Giniten agreement with or anitan permission from ‘ma corperence 72-JA1405B -

99-10081 , Figure 23 New Coin Door . . 71-10xxxx B ;

Page 45

Sit-Down Missile Command™ . -

Figure 23 New Coin Door, continued : , 38 . Parts List :

Part No. Description

31-1N4002 100V Silicon Rectifier 1N4002 Diode 65-4416 General-usage low-force miniature switch 70-11-47 Miniatura bayonet-base incandescent lamp, type #47 71-1201ADU U.S. $1.00 coin mechanism 71-1201FCH Swiss 1 Fr coin mechanism . 71-1201MG German 1 OM coin mechanism * 71-1202MG German 2 OM coin mechanism . 71-1205F8 Belgian 5 Fr coin mechanism 71-1205MG_ German 5 OM coin mechanism 71-1210PE U.K. 10 P coin mechanism. 71-1220CA Australian 20¢ coin mechanism . 71-1225CU US. 25¢ coin mechanism 71-12100U) Italian 100 Lire coin mechanism 71-12100YJ Japanese Y100 coin mechanism 72-HA1404C #4x%" Slotted pan-head thread-rolling tri-fluted “Taptite” cadmium-plated screw 72JA14058 #4x§/16” Slotted pan-head thread-rolling tri-fluted “Plastite” black screw 72-9406S #4-40x3/8" Siotted truss-head steel machine screw —

72-9603S#6-32x3/16" Slotted truss-head steel machine screw‘
75-9158#%-20 Standard pattern cadmium-plated steel hex nut\
75-9188#8-32 Standard pattern cadmium-plated steel hex nutNy

75-944S #4-40 Polymer self-ocking steel hex nut 75-948S #8-32 Polymer self-locking steel hex nut 75-1408S #4-40x ¥2" Slotted pan-head steel machine screw 75-1412S, #4-40x%" Slotted pan-head steel machine screw 75-§5208, #%-20x1%" Round-head square-neck steel boit with dlack finish 99-10008 ‘Switch wire retainer 99-10009 2-Mech coin door only 92-10010 3-Mech coin door only 99-10011 Inner panel 99-10012 - U.S. 25¢ coin return button assembly 99-10013 U.S. $1.00 coin return button assembly 99-10014 German 1 OM coin return button assembly 99-10015 German 2 OM coin return button assembly 99-10016 German 5 OM coin retum button assembly 9910017, Belgian 5 Fr coin return button assembly 99-10018 Swiss 1 Fr coin return button assembly 99-10019 Japanese Y100 coin return button assembly . 99-10020 U.K. 10 P coin return button assembly 99-10021 Australian 20¢ coin retum button assembly 99-10022 Italian 100 Lire coin return button assembly 99-10040 Coin inlet chute assembly 99-10041 Coin counter assembly 99-10042 Coin switch assembly for U.S. 25¢ and Belgian 5 Fr coins (silver wire)

-9910043Coin switch assembly for German 1 OM, Swiss 1 Fr, and Japanese Y100 coins(black wire)
99-10044Coin switch assembly for U.S. $1.00, German 2 OM, and Italian 100 Lire coins(gold wire)
Page 46

Sit-Down Missite Command™ Figure 23 New Coin Door, continued Parts List

Part No. Description

99-10045 Coin switch assembly for German 5 DM, U.K. 10 P, and Australian 20¢ coins (green wire) 99-10047 Lockout coil assembly . %

“e99-10048,Coin door harness assembly
Pa99-10049Locking arm assembly

99-10081 Coin door frame 99-10052 Coin return lever 99-10054 Coin button housing 99-10055 . Coin return button cover for Japanese Y100 coin 99-10058 Coin return button cover for German 1 OM and Swiss 1 Fr coins 99-10057 Coin return button cover for U.S, 25¢ and Belgian 5 Fr coins 99-10058 Coin return button cover for U.S. $1.00, German 2 OM, and Italian 100 Lire coins 99-10059 Coin return button cover for German 5 DM, U.K. 10 P, and Australian 20¢ coins 99-10061 Coin return bezel . 99-10062 Coin return button 99-10063 Right half of coin inlet chute 99-10064 Left half of coin inlet chute 99-10065 Coin return box 99-10066 Coin return cover 99-10070 U.S. 25¢ price plate 99-10071 Slam switch assembly 99-10073 Test switch decal 99-10074 . Lock assembly 99-10075 Black switch wire—for German 10M, Swiss 1Fr and Japanese Y100 coins 99-10076 - Silver switch wire—for U.S. 25¢ and Belgian SFr coins . e 5) 99-10077 Gold switch wire—for U.S, $1.00, German 20M and Italian 100 Lire coins A 99-10078 Green switch wire—for German 5DM, U.K. 10P and Australian 20¢ coins 99-10080 Miniature bayonet-base lamp socket 99-10081 Wire key holder 99-10082 Switch cover 99-10083, U.S. $1.00 price plate 99-10084 German 1 OM price plate 99-10085, German 2 OM price plate 99-10086 German 5 DM price plate 99-10087 Belgian 5 Fr price plate 99-10088 Swiss 1 Fr price plate 1 99-10089 Japanese Y100 price plate © 99-10090 U.K. 10 P price plate 99-10091 Australian 20€ price plate 99-10092 Italian 100 Lire price plate 99-10094 Fish paper insulation 99-10095 Toggle switch 99-10096, “U"-type fastener

.99-10097Fish paper insulation
‘99-10101Coin inlet chute sub-assembly

99-10102 Switch and lockout coil bracket sub-assembly

.99-16103Inner panel with levers sub-assembly.er)

99-10104 Anti-penny-flip bar retainer % 99-10105 Anti-penny-flip bar 99-10107 U.S. §0¢ coin return button assembly 99-10108 U.S. 50¢ price plate—for two quarters

Page 47

| . Sit-Down Missile Command | tst printing @() YOUR COMMENTS, PLEASE! \

e | Your comments will assist Atari in improving the usefuiness of our publications. They are an important part of preparing for revisions cf manuats and parts | catalogs. No postage stamp is necessary if mailed in the U.S.A. If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we wil! immediately forward your note to the appropriate person.

Page: Comments:

@ = Q@——— —-—————

Call

Fill in tf you wish a reply: Name Firm - = Distriburor | : Address, = Operator _— P e@ Cy i Stare LL Zi , = Other

Page 48

First told .

No Postage: Necessary if maded in the United Siates sg bn

cee et eee POSTAGE WILL BE PAID BY ADORESSEE \! Atari, Inc. | 3 |

Attn.: Field ServicelCoin-Op Division if

P.O. Box 427 3 Sunnyvale, Califomia 94086

ee TG

> Wold } | ¢ | €

a6pe sigs adey } i

Page 49

Warranty

Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty

  • days from date of shipment. None of the Seller's other products or parts thereof are warranted.

if the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are retumed to Seller during said warranty period, provided:

{a) Seller is promptly notified in writing upon discovery by Buyer that said products are defective;

  • Such products are retumed prepaid to Sellers’ plant; and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing:

In no event shail Seller be liable for loss of profits, loss of use, incidental or consequential

‘ Except for any express warranty set forth In a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty Is expressed in fleu of ail other warranties expressed or implied, inciuding the implied warranties of merchantabil- Ity and fitness for a particular purpose, and of all other obligations or Ilabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other Ilabilities in connection with the sale of products under this order.

The use of any nor-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause in- Jury to yourself and others. Be very cautious in using non-Atar-supplied components with our games, in order to insure your safety.

Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor. This document is and contains confidential trade secret information of Atari, Inc.

This document ‘is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atarl equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.

Neither it nor the information it contains may be reproduced, used, or disclosed to persons not hav ing a need to know consistent with the purpose of the foan, without written consent of Atari, Inc. E dlee Nalee, Sales Sabie Sate Satee, Sate Sate coal

Page 50

__ ATART ‘ATAAL ING 1265

408/745-2000 * TELEX 35-7488.