CATHODE RAY TOMES

19XX

19XX: The War Against Destiny (Europe 960104) (Capcom, 1996) · Manual · 22 pages · 46 sections · original scan

Page 1

OPERATORS MANUAL

/\ WARNING

This game is for use in the United States of America

and Canada. Sales, export or operation outside of

these countries may be constructed as copyright and

trademark infringements and is strictly prohibited.

Violators are subject to severe penalties and will be

prosecuted to the full extent of the law.

C/NPCOM® conor, ine. Avenue 3311 N. Kennicott Arlington Heights, Illinois 60004 Phone: (847) 797-6192 Fax: (847) 797-6306 PMO00145-KIT 020196

Page 2

19XX: THE WAR AGAINST DESTINY™

THANK YOU FOR PURCHASING 19XX: THE WAR AGAINST DESTINY™. WE INVITE

YOU TO USE THE FOLLOWING MAILING ADDRESS, TELEPHONE OR FAX NUMBER

FOR PARTS OR SERVICE INFORMATION CONCERNING THIS GAME:

CAPCOM® COIN-OP, INC.

THE SERIAL NUMBERS OF YOUR KIT ARE LOCATED ON THE GAME

CARTRIDGES AS SHOWN BELOW. PLEASE HAVE THESE SERIAL NUMBERS AVAILABLE WHEN CONTACTING US FOR SERVICE INFORMATION.

DEPENDING ON THE TYPE OF KIT YOU PURCHASED, PLEASE RECORD THE SERIAL NUMBERS HERE: “FULL” KIT A-CARTRIDGE SERIAL # B-CARTRIDGE SERIAL # AAMA SERIAL # “A” KIT A-CARTRIDGE SERIAL # “B” KIT B-CARTRIDGE SERIAL # _ AAMA SERIAL #

tary and confidential information, not to be disclosed or copied without the

Page 3

CAPO coin-op, inc. 19XX: THE WAR AGAINST DESTINY™

TABLE OF CONTENTS

Warranty Information «=| a asareasteisanscotensestoasvuosasetiasnseannsiitasncatassisasencessiasitietige i

KitInspection =§-———————_thentavsnententcesrsavievenconesvnasussiaenststsesnetevetsasvenssvendsescsntsiens 1

Kit Installation “FULL” Kit Installation Preparation Installation Marquee Control] Panel Wiring Test Bracket Game Cartridges “A” Kit Installation Preparation and Installation “B” Kit Installation Preparation and Installation

Test Mode Test Menu Accessing the Menu How to Select an Item Closing the Menu Menu Item Descriptions Configuration Menus Accessing the Menus Changing the Settings System Configuration Settings Game Configuration Settings

JAMMA Connections Auxiliary Cable Connections

Template : Control Panel Drill Hole(s)

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM@ i

Page 4

CANP@OMI* coin-op, nc. 19XX: THE WAR AGAINST DESTINY™

LIMITED PRODUCT WARRANTY (APPLIES TO DOMESTIC SALES ONLY)

CAPCOM® COIN-OP, INC. (Seller), warrants only to the initial purchaser of its products, that the items listed below are free from defects in material and workmanship under normal use and service for the warranty periods specified:

A. CPS II System Cartridges One (1) Year B. Electronic and Mechanical Components: (90) days

No other part of Seller's products are warranted.

Warranty periods are effective from the initial date of shipment from seller to its authorized distributors.

Seller's sole liability shall be, at its option, to repair or replace products which are returned to Seller during the warranty periods specified, provided:

A. Seller is notified promptly upon discovery by buyer that stated products are defective;

B. Such products are properly packaged and then returned, prepaid to Seller's designated.plant.

This warranty does not apply to any parts damaged during shipment or handling, or due to improper installation or usage, or alteration. In no event shall Seller be liable for any anticipated profits, loss of profits, loss of use, incidental or consequential damages or any other losses incurred by the customer in connection with the purchase of a CAPCOM® COIN-OP, INC. product.

WARRANTY DISCLAIMER

EXCEPT AS SPECIFICALLY PROVIDED IN A WRITTEN CONTRACT BETWEEN SELLER AND PURCHASER, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

IMPORTANT NOTICE

THIS SHIPMENT HAS BEEN CAREFULLY INSPECTED AND PROPERLY PACKAGED BEFORE LEAVING THE FACTORY. WE CANNOT ASSUME RESPONSIBILITY FOR BREAKAGE THAT MAY OCCUR DURING TRANSPORTATION OF THE GAME. IF THIS GAME IS DAMAGED UPON RECEIPT FROM THE CARRIER, IMMEDIATELY NOTIFY THE CARRIER AND FILE A DAMAGE REPORT.

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM®

Page 5

ICAR COME Ran 19XX : THE WAR AGAINST DESTINY™

KIT INSPECTION

There are three kits available for conversion to 19XX : THE WAR AGAINST DESTINY™:

  • 19XX1000 (“FULL” kit) contains the complete game cartridges, all necessary graphics, and replacement joysticks and button switches. The “FULL” kit is intended for conversion of most JAMMAcompatible, vertical screen cabinets.
  • 19XX1000A (“A” kit) is compatible only with current CAPCOM® System II games. It is similar to the “FULL” kit but does not include both cartridges (only the A-cartridge is supplied). For operators who have previously converted a vertical screen cabinet with a “B” kit, the purchase of an “A” kit will provide all the additional components necessary for “FULL” cabinet conversion (“A” + “B” = “FULL”)
  • 19XX1000B (“B” kit) contains the game software cartridge (B-cartridge) and must also be installed to a current CAPCOM® System II game. It includes all the necessary game graphics for a cabinet conversion (marquee, control panel overlay, monitor card, etc.).

Check that all parts have been shipped with your kit. If any parts are missing, contact your distributor immediately.

KIT PARTS LIST

19XX1000 19XX1000A | 19XX1000B PART NO. DESCRIPTION A-00635 CPS II System Cartridges (A/B ) ZZ1400A CPS II System Cartridge ( A ) A-00636 CPS II System Cartridge ( B ) GE1200 Monitor Card AW00190 Marquee 06-0074 Overlay, Control Panel AW00191 Decal, Joystick & Button Switches AW00147 Decal, Cabinet Side 19X961A03-1 Decal - Bottom, Game Play Instruction 19X961A03-2 Decal - Top, Game Play Instruction PM00145-KIT Manual, Operators 03-0052 Cable, Auxiliary GE2030 Joystick 16-0130 Switch, 1-Player Start Button (White) 16-0131 Switch, 2-Player Start Button (White) 16-0133 Switch, Button (Red) 16-0134 Switch, Button (Blue) 03-0050 __| Bracket, Volume/Test 13-0066 Bracket, A-Cartridge Shelf Mounting $C00104-05 Screw, Wood 13-0141 Clamp, Case 42}2}e}eje}/e]e}e}e] j2jejejelelelejelejelelelelelelej<) 2jejelejejelelelelel<)

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. 1

Page 6

CAPEOM* co-op, inc. 19XX : THE WAR AGAINST DESTINY™

[ CAUTION _

Please read the following instructions to keep the PC board in good condition:

Do not block the ventilation slots.

Do not drop or bump the board.

Do not spill any liquids on the case.

Do not disassemble the case.

ATTENTION

The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste system. Check with your local solid waste official for Ni-cd details in your area for recycling options or proper disposal.

DISASSEMBLING THE CASE OR REMOVING THE STICKER MAY CAUSE THE TERMINATION OF YOUR REPAIR WARRANTY

OF YOUR REPAIR WARRANTY.

2 Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 7

GAPE? co-op, INC.

“FULL” KIT INSTALLATION

AN WARNING:

MAKE SURE ELECTRICAL POWER TO THE GAME IS OFF BEFORE STARTING THE KIT INSTALLATION.

PREPARATION

  • Disconnect and remove the old printed circuit board(s) from the cabinet.
  • Remove or open the control panel, and disconnect and remove the buttons and joystick(s) from the control panel.
  • Remove any covering from the control panel overlay, and then remove the control panel overlay.
  • Place the Drill Hole template over the control panel to determine where any new holes should go. Center punch any needed new holes on the control panel.
  • Cut out the new holes using a 1-3/16" hole saw.
  • If there is an additional control panel cover (such as plastic or lexan) that will be utilized, cut any additional holes using the same template.
  • Plug up unused holes with a wood dowel (1- 1/8" diameter) and sand any rough edges.

INSTALLATION

Marquee Installation

  • Remove the marquee glass, old marquee overlay, and the old cabinet graphics.
  • Install the new marquee and replace the glass.

Control Panel Overlay Installation (See Figure 1)

  • The control panel overlay in the kit is oversized to accommodate most control panel sizes. Center the overlay on the control panel, leaving some excess material at the edges. 19XX : THE WAR AGAINST DESTINY™
  • Remove the protective backing from the overlay and press it down on the control panel, keeping it properly aligned. Press it down firmly, smooth out any bubbles, and press it over the edges.
  • Trim any excess from the overlay. Place the drill hole template on top of the overlay, aligning it with the joystick holes. Pierce through the overlay at each control panel hole. Then, cut away overlay material covering the joystick and button holes. Remove the template and clean off the overlay.
  • Peel off the backings of the 6-button and joystick decals, align over the control panel holes, and press in place on the overlay (refer to the drill hole template for proper placement). Using a knife, trim material from the center hole of the joystick decal.
  • Install the control panel cover (if required).

Control Panel

Figure 1 Overlay Installation Reassembly of Components

  • Install all buttons and retaining rings on the control panel as shown in Figure 2. Install two RED buttons to the immediate right of each joystick and install two BLUE buttons to the immediate right of the green ones.

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. 3

Page 8

® (CA\RCOM\ COIN-OP, INC. 19XX : THE WAR AGAINST DESTINY™

Control Panel Red Blue Red Blue

fer conm = \

eS Buttons I wi Nai © Retaining Ss Rings SS) ye Switches oF we FIGURE 2 Control Panel Buttons and Switches

  • Notice that there are two white buttons. (See Figure 3.) Install the PLAYER ONE button on the top left-hand side of the control panel, and the PLAYER TWO button on the top right-side of the control panel. The WHITE buttons are START buttons.

1 Player 2 Player @ SZ

FIGURE 3 Function and Start Buttons

  • Install the switched on the buttons as shown in Figure 2. Orient the switches so that when a button is pressed, the red contact on the switch is depressed.
  • Install the joysticks on the control panel as shown in Figure 4. FIGURE 4 Joystick Installation

CABINET DECAL INSTALLATION

  • Remove monitor glass and install monitor card.
  • Peel-off the backing to the instruction decals and place on both the top and the bottom sides of the monitor card. (See Figure 5). Also, apply the cabinet decals to both sides of the cabinet.

oot MONITOR. EZ a CARD "CABINET DECAL

INSTRUCTION

INSTRUCTION DECAL - TOP

DECAL - BOTTOM.

FIGURE 5 Cabinet Decal Installation

4 Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. |

Page 9

ICARCOMY COIN-OP, INC. 19XX : THE WAR AGAINST DESTINY™

System Wiring

NOTE: All switch wires used in this game must be wired to

the normally-open connection on the switches. Each switch requires a ground wire on the common connector and the appropriate control or switch wire on the normally-open connector of the switch.

  • Reconnect the existing JAMMA connectors to the control panel according to the chart of Figure 6.

WHITE/BLACK PLAYER | TO GAME CASE CONNECTOR

TO PUSH-BUTTON ‘SWITCHES (NOT USED)

TO VOLUME & TEST SWITCHES FIGURE 6 Auxiliary Cable Harness

COMPONENT JOYSTICK FUNCTION

WHITE/BROWN PLAYER | WHITE/RED JOYSTICK, JOYSTICK WHITE/ORANGE JOYSTICK WHITE/YELLOW. BUTTON SWITCH WHITE/GREEN BUTTON SWITCH WHITE/BLUE BUTTON SWITCH NO CONNECTION

VIOLET/BLACK PLAYER 2 JOYSTICK UP. VIOLET/BROWN PLAYER 2 JOYSTICK VIOLET/RED PLAYER 2 JOYSTICK DOWN

VIOLET/ORANGE PLAYER 2 NVIOLET/YELLOW PLAYER 2 JOYSTICK BUTTON SWITCH VIOLET/GREEN

  • Wire Color Note:

AUXILIARY CABLE CONNECTOR REF. VIOLET/BLUE PLAYER 2 PLAYER 2 BUTTON SWITCH BUTTON SWITCH

Figure 7: JAMMA Wiring Connections NO CONNECTION

Wire colors shown are according to the AAMA -AMOA Standard for wire color assignments; your harness may contain different colors than shown above.

WIRE COLOR BLACK NO CONNECTION CONNECTS TO COMPONENT FUNCTION

BLUE NO CONNECTION RED NO CONNECTION PINK NO CONNECTION BLACK NO CONNECTION NO CONNECTION PINK/YELLLOW NO CONNECTION | GRAY/YELLOW PURPLE/YELLOW_ NO CONNECTION GRAY/YELLOW, TEST BRACKET VOLUME SWITCH PINK/YELLOW TEST BRACKET VOLUME SWITCH BLACK/WHITE

Figure 8: Auxiliary Cable Wiring Connections TEST BRACKET VOLUME SWITCH

Proprietary and conf 3Fmation, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 10

ICAIRCOMY COIN-OP, INC.

  • An optional Test/Volume bracket (see Figure 9) is included in this kit. Your cabinet may already contain this bracket. If you decide to install, the bracket should be mounted inside the coin door and on top of the cash box for easy access.
NOTE: The A-cartridge also contains the same Test and Volume functions found on the test bracket.

uP + VOLUME

v300500 Figure 9: Test Bracket

Wiring of the Test Bracket requires connections to both the main JAMMA harness as well as the auxiliary cable harness (refer to Figures 6,8, &, 10).

TO LEAD WIRE

AUX. CABLE COLOR YELLOW “29°(GRAY/ YELLOW) SWITCH FUNCTION VOLUME-UP

GREEN COMMON AUX. CABLE “31’(BLACK/ WHITE) BLACK VOLUME- DOWN AUX. CABLE ‘30’ (PINK/ YELLOW) COMMON AUX. CABLE ‘31°(BLACK/ WHITE)

TEST JAMMA ‘15”

GROUND JAMMA ‘A’ or ‘B’ or ‘e’ or ‘f or “VY or ‘2’ or ‘27° or ‘28 Figure 10: Test Bracket Wiring Chart 19XX : THE WAR AGAINST DESTINY™

GAME CARTRIDGE INSTALLATION

  • Install the four (4) mounting brackets to the underside of the “A” cartridge as shown in Figure 11.

ZF S x

Figure 11: Mounting Bracket Installation

  • Using the supplied wood screws, fasten the game cartridge case to the control panel shelf, as shown in Figure 12.

Figure 12: Case Mounting

  • Connect the JAMMA harness connector and the auxiliary cable connector to the “A’ cartridge. If your cabinet is equipped with Q- SOUND, also attach the audio cables.

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 11

@ANP@ONI° coin-op, INC.

WARNING

Improper installation of the JAMMA harness connector to the game cartridge will cause damage to the enclosed PCB.

  • | Power-up the game and set all operator adjustable options by pressing the TEST switch. Follow the instructions under the TEST MENU section of this manual.

“A” KIT INSTALLATION

  • To install the control panel parts, you must follow the “FULL” Kit Preparation and Installation Procedure, steps 15 through 18 and steps 21 & 22.
  • To mate the existing “B” cartridge with the “A” cartridge, align the “B” cartridge over the “A” cartridge and push down firmly. Install the case clamps as shown in Figure 12.

Case Clamp

"A" Cartridge

Figure 12 : Case Clamp Installation 19XX : THE WAR AGAINST DESTINY™

  • Continue to follow the “FULL” kit Preparation and Installation Procedure, steps 24 through 26.
  • Installation of the “A” kit is now complete.
WARNING

DISASSEMBLY OF EITHER GAME CARTRIDGE WILL VOID YOUR WARRANTY.

“B” KIT INSTALLATION

  • To install the cabinet graphics, you must follow the “FULL” Kit Preparation and Installation Procedure, steps 3 through 21.
  • To remove the existing “A” cartridge from the “B” cartridge, pull the old case clamps apart and discard (see Figure 12). Carefully remove the old “B” cartridge and install the new “B’ cartridge. Install the new case clamps.
  • Power-up the game and set all operator adjustable options by pressing the TEST switch. Follow the instructions under the TEST MENU section of this manual.

[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. 7

Page 12

GAPEONI coin-op, Inc. 19XX : THE WAR AGAINST DESTINY™

NOTES

8 [Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 13

CANE coin-op, Inc. 19XX : THE WAR AGAINST DESTINY™

TEST MENU

The test menu allows you to test the functions and configure the game. These items include input devices such as joysticks, buttons and coin mechs, output devices such as monitor, speakers and meters. Through the Test Menu you can also access the Configuration Menu, where you can change the settings of the game.

  • ACCESSING THE TEST MENU

¢ For a CAPCOM® cabinet, or a cabinet with a test switch: Make sure the game is on and push the test switch. The screen shown below will appear.

¢ For a cabinet without a test switch: Push the test switch test on the outside of the blue plastic casing. (Refer to the inside back cover of the manual).

INPUT

OUTPUT

SOUND & VOICE

COLOR

DOT CROSS HATCH

GAME DATA

CONFIGURATION

MEMORY CHECK

  • EXIT

SELECT = 1P UP or DOWN START =1P SHOT1

  • HOW TO SELECT AN ITEM

© Use the PLAYER I JOYSTICK to move the arrow in front of the desired item and press the PLAYER I SHOOT button.

  • To return to the test menu, push the PLAYER ] START and PLAYER 2 START buttons simultaneously.

[Frevrieter ‘and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN.OP, INC, 9

Page 14

CAPCOM co-op, nc. 19XX : THE WAR AGAINST DESTINY™

° The test menu will always appear on the screen:

  • After you exit the “7. CONFIGURATION MENU” and
  • After the memory is tested from the menu, “8. MEMORY CHECK”.
  • CLOSING THE TEST MENU To close the Test Menu, highlight ‘9. EXIT” and push the PLAYER 1 SHOOT button.
  • TEST MENU ITEM DESCRIPTIONS

[INPUT Used to test all the input switches, such as joysticks and buttons. The “0” changes to a “1” as the button is pushed or joystick is moved. Check connections and switches in case the “0” doesn’t change to a “1” when depressed or moved.

OUTPUT Used to test the coin meter and the coin lock.

SOUND & VOICE Select a code of SOUND or VOICE with the PLAYER I JOYSTICK. Push the PLAYER I SHOOT button to hear the sound of the selected code.

COLOR Shows color bars of red, green, blue, and white. Adjust RGB and brightness to obtain the optimum color balance and solid black background.

DOT CROSS Used to test the screen size, focus and distortion. HATCH GAME DATA Coin meter and playtime information will be displayed.

CONFIGURATION _ | Used to change the game play settings. Refer to the CONFIGURATION MENU section.

MEMORY CHECK | Used to test memory. “OK” appears when each block of memory passes test, “NG” appears in case of malfunction. If “NG” appears, repeat the memory test and wait for the “OK” message. Contact your distributor if “NG” still appears.

EXIT Select this item and push the PLAYER 1 SHOOT button to return to game play mode.

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN.OP, INC.

Page 15

@ANP@OHI coin-op, Inc. 19XX : THE WAR AGAINST DESTINY™

CONFIGURATION MENU

The Configuration Menu is used to change various game settings such as level difficulty, credits, sound configuration, etc. These settings are stored in memory on the PCB rather than DIP switches.

The Configuration Menu is divided into 2 sections. In the SYSTEM section, you can change credits, sound, and coin door configurations. In the GAME section, you can change the play difficulty level and duration of the game.

  • ACCESSING THE CONFIGURATION MENU ¢ From the TEST MENU, move the arrow to “7. CONFIGURATION” and push the PLAYER I SHOOT button. The screen below will be displayed. A description of each option is explained in the table below.
  • CONFIGURATION MENU

. SYSTEM

. GAME

  • DEFAULT

. SAVE & EXIT

SELECT 1P UP OR DOWN START 1P SHOT1

SYSTEM | Select this item to change settings for credits, monitor flip, sound and coin door configurations. GAME Select this item to change difficulty level, damage level, time count speed, maximum number of rounds and event type. DEFAULT | Use this item to restore configuration settings to the original factory values. Press the PLAYER I SHOOT and PLAYER I] BOMB buttons at the same time to select this | option. SAVE & Use this to save new configuration settings and exit to the Test Menu. The message EXIT “SAVING NEW CONFIGURATION IN EEPROM” will appear while the new settings are being saved. DO NOT turn power off to the game until “SAVING” is complete and the Test Menu reappears.

[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. I

Page 16

CARPREONI* comn-op, nc. 19XX : THE WAR AGAINST DESTINY™

SYSTEM CONFIGURATION

CHANGING THE SYSTEM CONFIGURATION SETTINGS

Move the PLAYER I JOYSTICK up or down to highlight the desired option. Once the option is highlighted, move the PLAYER J JOYSTICK left or right or press the PLAYER ] SHOOT button to

select. 7-1. SYSTEM CONFIGURATION

> 1. COIN MODE 1 COIN 1 CREDIT

. CONTINUE ON

. MONITOR NORMAL

|. DEMO SOUND ON

  • SOUND MODE STEREO (QSOUND)

. CHUTER TYPE 2 CHUTES SINGLE

|. EXIT

SELECT OPTION 1P UP OR DOWN MODIFY SETTING 1P LEFT OR RIGHT = 1P SHOT1 OR SHOT2

SYSTEM CONFIGURATION ITEM DESCRIPTIONS

  • COIN SELECT THE CHARGE PER PLAY.
  • CONTINUE, SELECT ON FOR CONTINUOUS PLAY OR OFF FOR NON-CONTINUOUS PLAY.
  • MONITOR FLIP FLIPS THE POSITION OF THE SCREEN. IF THE SCREEN APPEARS UPSIDE-DOWN, CHANGE THE SETTING TO. FLIP; IF THE SCREEN APPEARS CORRECT, SELECT NORMAL.
  • DEMO SOUND TURNS ATTRACT SOUNDS ON OR OFF.
  • SOUND MODE SELECT STEREO OR MONAURAL FOR USE WITH YOUR CABINET.
NOTE: STEREO SHOULD ONLY BE SELECTED FOR USE WITH CAPCOM® QSOUND CABINETS.
  • CHUTER TYPE SELECT THE NUMBER OF PLAYER(S) AND COIN CHUTES. 1 CHUTE SINGLE: WITH THIS SETTING, EITHER PLAYER CAN START THE GAME. 2 CHUTES SINGLE: TWO PLAYERS USE ONE COIN CHUTE AND PLAY AT THE SAME TIME. THE PLAYER WHOSE COIN WAS PUT IN FIRST STARTS THE GAME. 2 CHUTES MULTI: TWO PLAYERS USE TWO COIN CHUTES AND PLAY SEPARATELY. THE GAME STARTS FROM THE SAME SIDE AS THE COIN CHUTE WAS USED.
  • EXIT TO SAVE THE SETTINGS AND RETURN TO THE CONFIGURATION MENU, HIGHLIGHT THIS ITEM AND PUSH THE PLAYER | START BUTTON

SYSTEM CONFIGURATION OPTION SETTINGS

1COIN1. COIN1 COIN1 COIN1 COIN
1 CREDIT2CREDITS3. CREDITS.4 CREDITSS CREDITS
1 COIN1 COIN1 COIN1 COIN2 COINS
6 CREDITS7CREDITS8 CREDITS9CREDITSCREDIT
3 COINS:‘4 COINS‘5 COINS‘6 COINS7 COINS
1 CREDIT.1 CREDIT1 CREDIT1 CREDITL CREDIT
8 COINS‘9 COINS,2 COINS STARTFREE PLAY
1 CREDIT.1 CREDIT1 COIN CONTINUE
  • CONTINUE. ‘ON. OFF 3, MONITOR [ FLIP, NORMAL. 4, DEMO SOUND. ‘ON OFF ‘5. SOUND MODE STEREO (Q SOUND) MONAURAL
  • CHUTE TYPE 1 CHUTE SINGLE 2 CHUTES SINGLE 2 CHUTES MULTI

NOTE: FACTORY SETTING

12 Proprietary and confidential information, not tobe disclosed oF copied without the express permission of CAPCOM@ COIN-OP, INC.

Page 17

GANP@OHI° coin-op, Inc. 19XX : THE WAR AGAINST DESTINY™

GAME CONFIGURATION

CHANGING THE GAME CONFIGURATION SETTINGS

Move the PLAYER |] JOYSTICK up or down to highlight the desired option. Once the option is highlighted, move the PLAYER J JOYSTICK left or right or press the PLAYER I SHOOT button to select. 7-2. GAME CONFIGURATION

. NUMBER OF PLAYERS 3

. DIFFICULTY EASY(***4****)HARD

. EXTEND 1ST LEVEL 10 2ND LEVEL 25

. BOMB STOCKS 3

  • EXIT

SELECT OPTION = 1P UP OR DOWN MODIFY SETTINGS =1P LEFT OR RIGHT = 1P SHOT 1 OR SHOT

GAME CONFIGURATION ITEM DESCRIPTIONS

  • NUMBER OF _ | SETS THE INITIAL NUMBER OF FIGHTER PLANES. PLAYERS 2.DIFFICULTY | SETS THE GAME DIFFICULTY.
  • EXTEND SETS THE FIGHTER LEVEL AT WHICH THE PLAYER WILL RECEIVE 1UP.
  • BOMB SETS THE INITIAL NUMBER OF BOMBS. STOCKS [S-EXIT RETURN TO THE CONFIGURATION MENU. ]

GAME CONFIGURATION OPTIONS

1. NUMBER OF25

PLAYERS

2. DIFFICULTY14

EASIEST. VERY EASY MEDIUM 5 6 8 MEDIUM HARD HARD VERY HARD HARDEST

  • EXTEND NOTHING IST LEVEL 15 1ST LEVEL 15 1ST LEVEL 10 2ND LEVEL 25 2ND LEVEL 25
4. BOMB0i23

STOCKS

NOTE: | FACTORY SETTING

[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN.

Page 18

ICARCOMY COIN-OP, INC. 19XX : THE WAR AGAINST DESTINY™

JAMMA Connections

SOLDER SIDE COMPONENT SIDE

po] oy] | oo] > COIN COUNTER | COIN LOCK 2 COIN LOCK 1 *SPEAKER (-) *SPEAKER (+) N.C. VIDEO GREEN N.C. VIDEO RED VIDEO SYNC SERVICE (FREE CREDIT) VIDEO BLUE VIDEO GROUND NIC TEST MODE 2 PLAYER - COIN 1 PLAYER - COIN 2 PLAYER - START 1 PLAYER - START 2 PLAYER - UP 1 PLAYER - UP 2 PLAYER - DOWN 1 PLAYER - DOWN 1 PLAYER - LEFT 1 PLAYER - RIGHT 1 PLAYER - SHOT 2 PLAYER - LEFT 2 PLAYER - RIGHT 2 PLAYER - SHOT 2 PLAYER - BOMB 1 PLAYER - BOMB NIC N/C NIC GND GND

NIC alo lafo|o]» |N}<}<]=l<}q)4]a]a)ul zlz|e]x

NIC NIC NIC NIC NIC NIC NIC NIC NIC NIC NIC NIC NIC GRAY/YELLOW TEST BRKT-VOLUME UP. BLACK/WHITE TEST BRKT-VOLUME COMMON BLACK NIC

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. PINK/YELLOW

Page 19

\

1-3/16" DRILL FOR PLAYER HOLE

1-3/4" DRILL FOR JOYSTICK HOLE — _

1-3/16" DRILL FOR BUTTON HOLES

CAPCOM CONOP, INC. 3311 NORTH KENNICOTT AVENUE

PHONE (708) 797-6100 FAX (708) 797-6119 THLE

"19XX" DRILL TEMPLATE

DATE DRAWN BY: 1-22-96 JA

'v80200 = |=

Page 20

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 21

(CARCOMY INC. 19XX: THE WAR AGAINST DESTINY™

REFERENCE INFORMATION

JAMMA. AUXILIARY CABLE AUDIO OUT (FOR Q SOUND) ‘va00800

NOTE: IF YOU ARE EXPERIENCING VOLUME CONTROL PROBLEMS, DEPRESS AND HOLD

VOLUME DOWN FOR AT LEAST FIVE SECONDS AND RELEASE. THEN, SET VOLUME UP

FOR APPROPRIATE SOUND LEVEL. FOR SOUND LEVEL VERIFICATION, FOLLOW THE

INSTRUCTIONS IN THIS MANUAL UNDER TEST MENU, SOUND & VOICE.

TYPICAL CONTROL PANEL LAYOUT OF 19XX: THE WAR AGAINST DESTINY™

Page 22

NOTICE

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

WARNING

3311 N. Kennicott Avenue

Heights, Illinois 60004

Phone: (847) 797-6192 Fax: (847) 797-6306

Copyright © 1995 CAPCOM ® coin-op, INc., All Rights Reserved