CATHODE RAY TOMES

Galaga Parts and Operating Manual (Oct 1981)

Galaga (Namco rev. B) (Namco, 1981) · Parts & Operating Manual · 89 pages · 42 sections · original scan

Page 1

OCTOBER, 1981 Game Nos. 508, 514 & 510

] MIDWAYS

No. 510 COCKTAIL ae

No, 508 UPRIGHT

MIDWAY MFG. CO. A BALLY COMPANY

10750 W. GRAND AVENUE FRANKLIN PARK, ILLINOIS 60131 USA

No. 514 MINI

Form No. 0508-00300-0000

Page 2

Sees mae

WARNING THIS GAME MUST BE GROUNDED. FAILURE TO DO SO MAY RESULT IN DESTRUCTION TO ELECTRONIC COMPONENTS.
WARNING: This equipment Generates, Uses and can Radiate Radio Frequency Energy and if not installed and used in accordance with the Instructions Manual, may cause interference to Radio Communications. As temporarily permitted by Regulation it has not been tested for compliance to Subpart J or Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference. Operation of this equipment in a Residential Area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.

ELECTRICAL BULLETIN: FOR ALL APPARATUS COVERED BY THE CANADIAN STANDARDS ASSOCIATION (CSA) STANDARD C22.2 NO. 1, WHICH EMPLOYS A SUPPLY CORD TERMINATED WITH A POLARIZED 2-PRONG ATTACHMENT PLUG.

CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET

ear BLADES CAN BE FULLY INSERTED TO PREVENT BLADE

ATTENTION: POUR PREVENIR CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR. UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT.

MIDWAY MFG. CO.

our TOLL FREE NUMBERS FOR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER MIDWAY GAME YOU NOW HAVE ON LOCATION.

CALL US FOR PROMPT, COURTEOUS ANSWERS TO YOUR PROBLEMS. Continental U. §. 800-323-7182 IMlinois Only 1-800-942-0497

COPYRIGHT 1981 ©BY MIDWAY MFG.CO. ALL RIGHTS RESERVED.

NO PART OF THIS PUBLICATION MAY BE REPRODUCED BY ANY MECHANICAL, PHOTOGRAPHIC, OR ELECTRONIC PROCESS, OR IN THE FORM OF A PHONOGRAPHIC RECORDING, NOR MAY IT BE TRANSMITTED, OR OTHERWISE COPIED FOR PUBLIC OR PRIVATE USE, WITHOUT PERMISSION FROM THE PUBLISHER. FOR PERMISSION REQUESTS, WRITE: MIDWAY MFG. CO., 10750 W. GRAND AVE., FRANKLIN PARK, IL 60131

Printed In U.S.A.

Page 3

DESCRIPTION TABLE OF CONTENTS

Introduction

Location and Setup . Inspection . Installation. Self-Test..... Game Volume Adjustment Control Option Switch Settings ........... Eliminating the Rapid (Automatic) Fire Feature Game Operation Self-Test Mode ... Attract Mode...... Ready-to-Play Mode Play Mode... Two Player Operation ...

Maintenance and Repair.........- 66... ccc cece cence nee eee nent e renee teen eee 3- Cleaning........... . Fuse Replacement ... Opening the Control Panel Removal of Main-Display Glass and T.V. Bezel. T.V. Monitor Replacement ........ Printed Circuit Board Replacement. . Opening the Attraction Panel .. Coin Door Maintenance

Illustrated Parts Breakdown Galaga Control Assembly — All Versions Gaiaga Control Assembly — All Versions — Parts List Front Door Assembly — U.S.A. 25¢ . Front Door Assembly — U.S.A. 25¢ — Parts Galaga — Card Rack Assy. w/Boards — All Versions Galaga — Card Rack Assy. w/Boards — All Versions — Parts List Galaga — Transformer Board Assy. —- Parts List No. 508 — Galaga Upright — Front........... No. 508 — Galaga Upright — Front — Parts List No. 508 — Galaga Upright — Rear Access No. 508 — Galaga Upright — Rear Access — Parts List . No. 508 — Galaga Upright — Header Fluorescent Fixture Assy. No. 508 — Galaga Upright — Header Fiuorescent Fixture Assy. — Parts List . No. 514 — Galaga Mini-Front............. No. 514 — Galaga Mini-Front — Parts List. No. 514 — Galaga Mini — Rear Access. . No. 514 — Galaga Mini — Rear Access — Parts List .. No. 510 -- Galaga Cocktail — Front.............. No. 510 — Galaga Cocktail — Front — Parts List ... No. 510 — Galaga Cocktail — Interior Access No. 510 — Galaga Cocktail — Interior Access — Parts List

Page 4

Vi.

vil. TABLE OF CONTENTS (cont'd)

Technical Troubleshooting . 5-1 Introduction ........ General Suggestions .. Harness Component Troubleshooting ... Transformer and Line Voltage Problems . A Glossary of Microprocessor Terms. . Introduction to the Z-80 CPU General Purpose Registers ... Arithmetic and Logic Unit (ALU) .. Instruction Register and CPU Control Z-80 CPU Pin Description ........ Basic Logic and Processor Books.

T.V. Monitor Manual... Introduction ...... Sympton Diagnosis ... Guide to Schematic Symbols Troubleshooting ...... Theory of Operation... Differences Between Monitors Parts Interchangeability

Schematics and Wiring Diagrams Wiring Diagram — Upright. Wiring Diagram — Mini.. Wiring Diagram — Cocktail Power Supply PCB —- Component Layout Power Supply PCB — Schematic ... Video Board — Component Layout . Video Board — Schematic . CPU Board — Component Layout CPU Board — Schematic ........... Rapid Fire PCB — Component Layout Rapid Fire PCB — Schematic....... Filter Board — Component Layout Filter Board — Schematic ......

TABLE OF FIGURES FIGURE "PAGE

pwr + ODNAAE RON

NAS Location of serial number, interlock switch and ON/OFF switch Location of volume control and option switch .. Option switch settings. Self test display....... Board location coordinates (self test display) . Opening Cocktail game .............- Removing monitor from Upright game. Removing monitor from Mini game. . Removing monitor from Cocktail game . P.C.B. replacement..............- Opening the metal coin acceptor Lubricating the metal coin acceptor . Changing the plastic coin acceptor for American or Canadian Quarters ..

Page 5

I Introduction

Page 6

Galaga

IMPORTANT NOTE

DO NOT plug in your new game yet. Before you do anything to your game, we recommend that you read SECTIONS | and II of this manual completely. It will not take more than a few minutes and it may be very helpful.

Introduction

GALAGA is a one or a two player game. There are three models: the “UPRIGHT”, “MINI”, and “COCK- TAIL TABLE”. When the two player mode is selected on the Upright or Mini model, the players take turns at the controls to fly their space fighter(s) through the game course. if you have purchased the Cocktail Table mode! of this game, the rules of play are the same. The only difference is that in the two player mode of the Cocktail Table game, the picture flips to face you when it's your turn. When playing this game, you are the pilot of a space fighter stationed in space to defend your planet against the on-coming hordes of invaders. Your mission is to destroy as many of the enemy ships as possible. These invaders arrive in convoys. They will attack you while swerving back and forth across the screen, dropping bombs all the while. Certain of the enemy ships can put out a tractor beam and capture your space fighter. That fighter changes color from white to red and stays with that particular enemy ship for the rest of the game. You can get it back by destroying the enemy ship that captured it while they are both attacking your current fighter. If you do this, the rescued ship changes color again from red back to white, and links up with your current fighter. This doubles your fire power. As your skill level increases, the number of attackers coming at you at any one time and the speed with which the enemy ships attack is gradually increased, plus their attack patterns become more and more complex. Bonus ships are awarded to you periodically throughout the game as you reach or pass certain preselected point values. Each enemy ship has an assigned point value.

Major New Features

Two major new features of your GALAGA game are:

  • The player is given the chance to double his fire power at certain points throughout the game, and 2) The game has a rapid fire (automatic firing) option whereby the player just holds the FIRE button down and his space fighter continues to fire at the GALAGAS in bursts of two missiles each. To double his fire power, the player must let one of his space fighters be captured by one of the GALAGA command ships and then rescue it. The GALAGA command ships MUST BE SHOT TWICE to destroy them. When shot once, they change color from green to blue. When shot again, they explode. The rescued fighter then links up with the one that rescued it and they now work as a team — both moving together and firing at the same time.

Game Objective

The object of the game is to survive as long as possible while destroying as many attacking ships as you can. As you do this, each following convoy of attackers will be harder to destroy.

Page 7

Il Location and Setup

Page 8

Location and Setup

INSPECTION: INSTALLATION:

1, Remove the game from its shipping crate. 1. Location requirements:

  • Inspect the entire outside of it for any signs of Power: damage. e Any scratches?, dents?, cracks? @ Any broken controls? @ Any broken glass or plastic? e Just look it over closely and make a note of any signs of damage.
  • Remove the shipping cleats from the bottom of the cabinet.
  • install the four levelers, one at each corner of the cabinet. e Level the cabinet.
  • Open the cabinet and inspect the inside of the game for any signs of damage. e Also check to make sure all plug-in connectors on the wire harness are firmly seated.
NOTE: ALL Connectors or piugs are keyed so they will only go together when all pins are properly lined up.

e Replug any connectors found unplugged. DO NOT FORCE PLUGS ONTO CONNEC- TORS. DO NOT FORCE PLUGS TOGETH- ER. If it won't go on easily, assuming the keys are lined up, it either does not belong there or is damaged. e Make sure all printed circuit boards (P.C.B.’s) are firmly seated in their connectors. These connectors are also keyed. The P.C.B.’s will only go into them one way without being damaged. @ Note the location of the games serial number. See Figure 1. e Check all major subassemblies to be sure they are mounted securely. Power supply. Control panel(s). T.V. monitor. Other P.C.B.'s and/or P.C.B. rack, etc. Power supply filter assembly. Transformer board assembly.

  • Make a note of any problems that can't be easily corrected.
  • Call your distributor and/or service man about your problem list.

2-1 Domestic 110 V @ 60 Hz Foreign 200 V to 240 V @ 50 Hz Temperature: 32° to 100°F (0° to 38°C) Humidity: Not over 95% relative Space required Upright 25" x 33” (63 x 84 cm) Mini 20" x 24” (50 x 60 cm) Cocktail 32" x 22” (81 x 55 cm) Game height: Upright 70” (175 cm) Mini 59" (148 cm) Cocktail 29" (73 cm)

  • Voltage Selections: Your game is designed to work properly on the line voltage where you are located. Check your line voltage with a meter to determine what its value is. Then check the power input wires to the main power supply transformer on your game to be sure they are connected to taps which correspond to your line voltage value. \f the power input wires to the main power supply transformer are not connected to taps which correspond to your local line voltage, move them to the proper taps. If the line voltage in your area falls outside the upper or lower limits of the range of inputs covered by the main power supply transformer, DO NOT PLUG YOUR GAME IN until you have talked with your distributor and/or service man and obtained a solution to this problem. Otherwise you could damage your game.
  • interlock and power ON/OFF switches. (See Figure 1. e To help prevent the possibility of getting an electric shock while working inside the game cabinet, interlock switches have been installed at each cabinet access door (this DOES NOT include the coin door in the Upright and Mini models).
Page 9

SERIAL NUMBER

SERIAL NUMBER

INTERLOCK

ON/OFF SWITCH

ON/OFF SWITCH

SERIAL NUMBER (MAY BE LOCATED ON ANY CORNER)

INTERLOCK SWITCH (INSIDE DOOR) COCKTAIL INTERLOCK SWITCH

ON/OFF SWITCH UNDER TABLE ON PLAYER 2 SIDE

Figure 1. Location of serial number, interlock switch and ON/OFF switch.

2-2

Page 10

@ When any access door is opened, the interlock switch installed there turns off all power to the game. @ Check each interlock switch for proper operation. After checking the line voltage in your area and determining that the input wires to the main power supply transformer of your game are connected properly — or — after obtaining a solution to your over or under voltage problem from your distributor and/or your service man, plug the game into your A.C. wall outlet. The game ON/OFF switches for all models are located as shown in Figure 1. Turn the game on and allow it to warm up a few minutes. Slowly open each access door to the game (this does not include the coin door on the Upright and Mini modeis). As the door is opened approximately 1” (2.54cm) the power to the game should go off (the T.V. monitor, ali the lights, and allsounds will stop). If this does not happen, check the interlock switch by this door to see if it has broken Joose from its mounting or if it is stuck in the “ON” position. If the switch is found to be bad, turn the game off, unplug it, and replace the interlock switch. When done, plug the game back into the wall outlet, close the access door, and turn the game back on. After the game has warmed up, repeat the above interlock switch test.

OPTION SWITCHES 6K 6J When the interlock switch is working properly and turns the power to the game off, power may be restored to the game with the access door(s) open. Take hold of the interlock switch plunger and gently pull it out to its fully extended position. THIS IS TO BE USED ONLY FOR SERVICING THE GAME.

SELF-TEST: Your new game will Self-Test itself to see if it has any bad parts. The information it receives while testing itself will be shown on the T.V. monitor. Some information can also be heard through the games speaker system. See the GAME OPERATION section for a more detailed description of this function. When there is a bad result according to the Self-Test, call your distributor and/or service man to have the trouble fixed unless it is something you can do yourself (such as replace a bad RAM or ROM chip).

GAME VOLUME ADJUSTMENT CON- TROL. SEE FIGURE 2. The game volume control pot is located on the CPU board. The other board is the video board. There is only one pot. For adjustment, it may be reached through the rear access door on the Upright and Mini models. On the Cocktail Table model, you will have to open the table top to reach it. To make the sounds louder, turn the pot clockwise as you face it (>). To make the sounds less loud, turn the pot counterclockwise as you face it (~— ).

VOLUME ADJUSTMENT

Figure 2. Location of volume control and option switch

2-3

Page 11

OPTION SWITCH SETTINGS:

To change the option switch settings, you DO NOT have to take the CPU board out of the game. They can be easily reached through the rear access door on the Upright and Mini models. On the Cocktail Table model, you do have to open the table top to reach them.

When changing any options, ALWAYS perform the Self-Test and play the game to be sure the switches have worked properly and that no switches were accidentally moved that were not meant to be. (These switches are small and this can happen.) The option switch settings and what they will make the game do are shown in Figure 3. See Figure 2 for option switch locations.

ELIMINATING THE RAPID (AUTOMATIC) FIRE FEATURE

(f you do not desire the RAPID (AUTOMATIC) FIRE FEATURE on your game, it can be simply and easily eliminated. See the following procedure.

  • Turn the power off to the game.

Figure 3. Option switch seitings

DIP SWITCH 6J

1 PLAYER GAME PRESS THE 1 PLAYER START BUTTON 2, 3, 4, OR 5 FIGHTERS OFF

2 PLAYER GAME PRESS THE 2 PLAYER START BUTTON 2, 3, 4, OR 5 FIGHTERS EACH

1 PLAYER GAME PRESS THE 1 PLAYER START BUTTON 2, 3, 4, OR 5 FIGHTERS

1 PLAYER GAME WITH 5, 7, 9, OR 11 FIGHTERS PRESS THE 2 PLAYER START BUTTON

SW#1SW#2SW#3 SWHdSW#5 SW#6 SW#7 SW#BE

NOT

DIFFICULTY LEVEL SETTINGS — “A” IS THE EASIEST AND “D” IS THE MOST DIFFICULT

SWH1SW#2 SWH#3 SW#4SW#5 SWH#E SWH7 SW#B
RANK “A” - EASIEST LEVEL OF PLAYOFFOFFNOT
RANK “12ND LEVEL OF DIFFICULTYONONUSED
RANK“C” - 3RD LEVEL OF DIFFICULTYOFFONNOT
RANK “D" - MOST DIFFICULT LEVEL OF PLAYONOFFUSED.

Swit SW#2 SW#3 SW#4 SW#5 SW#6 ON GAME PROVIDES SOUND IN ATTRACT MODE GAME DOES NOT PROVIDE SOUND IN ATTRACT MODE

FREEZE VIDEO (MONITOR PRESENTATION STOPS MOVING) MONITOR OPERATES NORMALLY

AUTOMATIC RACK ADVANCE NORMAL OPERATION OFF USED

SWSW#2 SW#3 SW#4SWHSSWHE SW#7 SW#8

NOT ON USED OFF ONE WAY TWO WAY

2-4

Page 12
  • UPRIGHT and MINI models: 3. Move the plug in the Rapid Fire P.C. Board from Unlock and open the rear access door. position “A”-RAPID, to position “B”-MANUAL.

COCTAIL TABLE model: 4. To close the game, reverse the opening pro- If you have this model, you will need to open the cedure. table top to reach the necessary terminal board. (See the appropriate opening procedure in the 5. Turn the power back on, run the game Self-Test, “MAINTENANCE AND REPAIR” section of this manual.) and play one game to make sure everything is working properly.

Figure 3. Option switch settings (Continued)

DIP SWITCH 6K

ISW#1 SWH2 SWH3 SWiH4 SWHS SWHE SWH7 SWHS FREE PLAY ON 4 COINS 3 COINS 2 COINS 2 COINS 1 COIN 1 COIN 1 COIN 1 CREDIT 1 CREDIT 1 CREDIT 3 CREDITS 3 CREDITS 2 CREDITS 1 CREDIT

BEGAN WITH 5 FIGHTERS ‘tst SHIP 2nd SHIP AND EVERY BEGAN WITH 2, 3 OR 4 FIGHTERS 1st SHIP 2nd SHIP AND EVERY 30000 100000

1st SHIP 2nd SHIP AND EVERY 1st SHIP 2nd SHIP 70000 AND EVERY

1st SHIP 2nd SHIP AND EVERY 20000 1st SHIP 80000 2nd SHIP 80000 AND EVERY 150000 150000 ON ON OFF OFF ON ON OFF OFF ON

ISW#1 SWH2 SWH3 SWH4 SWHS SWH6 SWH7 SW#B8

ON ON OFF

1st SHIP 2nd SHIP AND EVERY

1st SHIP 2nd SHIP AND EVERY

1st SHIP 2nd SHIP

1st SHIP 2nd SHIP 30000 100000 100000

30000 120000 120000 1st SHIP 2nd SHIP 30000 100000

1st SHIP 30000 2nd SHIP

1st SHIP 2nd SHIP 150000

30000 ONE SHIP ONLY

NO BONUS SHIPS GIVEN WITH THIS SETTING

DETERMINES NUMBER OF SPACE FIGHTERS PLAYER BEGINS GAME WITH:

2 SPACE FIGHTERS 3 SPACE FIGHTERS 4 SPACE FIGHTERS 5 SPACE FIGHTERS ON ON OFF OFF ON OFF ON OFF

2-5

Page 13

Game Operation

GALAGA is a one or a two player game with acolor T.V. monitor. The game has five possible modes of operation: ATTRACT, READY-TO-PLAY, PLAY, HiGH SCORE INITIAL, and SELF-TEST.

SELF-TEST MODE The Self-Test mode is a special mode for checking the game switches and computer functions. It is the easiest and best way to check for proper operation of the entire game.

NOTE: Putting the game into--Self-Test will cause it to erase any CREDITS shown at the lower left corner of the screen from its memory.

You may begin a Self-Test at any time by sliding the Self-Test switch to the “ON” position after the power to the game is on. Test switch is iocated inside coin door under coin meter. When this is done, the game will react as follows:

  • First, there is an explosion sound (sameas when your fighter is hit).
  • Immediately following this, you see an upside down test display which lasts for about 1/2 second. (By pushing both the “1 PLAYER” and the “2 PLAYER” buttons at the same time, the picture will turn upside down and stay that way until you release the buttons.)
  • And last, a righiside up test display is shown on the monitor screen. This will remain until you set the Self-Test switch back to the “OFF” position. This test display is shown below.

RAM OK or (a number and a (etter i.e. 1L, 3H, etc. ROM OK or (a number i.e. 01 21, etc.) UPRIGHT or (TABLE) *1 COIN *3 SHIPS RANK *A (B,C,D) “4 CREDIT

SOUND 00 (01,02,03,04,05,06,07,08,09, 10, 11,12, 13, 14,15, 16,17) 1ST BONUS *20000 PTS 2ND BONUS *70000 PTS “AND EVERY 70000 PTS

  • = switch selectable

Figure 4a. Self test display

  • \fabad ROMor RAM chipis found by the games internal check system during the Self-Test, the game indicates this to you by showing the location code of the bad chip(s) in place of the letters “OK”:

DISPLAY

RAM OK RAM OL RAM OH RAM 1L RAM 1H RAM 2L RAM 2H RAM 3L RAM 3H RAM 4L RAM 4H

ROM OK ROM 01 ROM 02 ROM 03 ROM 04 ROM 11 ROM 21 DESCRIPTION

All RAMs are good RAM located on Video PC board at position 1K is bad. RAM located on Video PC board at position 1K is bad. RAM located on Video PC board at position 1K is bad. RAM located on Video PC board at position 1K is bad. RAM located on Video PC board at position 3E is bad. RAM located on Video PC board at position 3F is bad. RAM located on Video PC board at position 3K is bad. RAM located on Video PC board at position 3L is bad. RAM located on Video PC board at position 3H is bad. RAM located on Video PC board at position 3J is bad.

All ROMs are good. ROM located on CPU PC board at position 3N is bad. ROM located on CPU PC board at position 3M is bad. ROM located on CPU PC board at position 3L is bad. ROM located on CPU PC board at position 3K is bad. ROM located on CPU PC board at position 3J is bad. ROM located on CPU PC board at position 3E is bad.

Figure 4b. Board location coordinates (Self test display)

2-6

Page 14
  • “RANK” is a difficulty setting, with “RANK A” being the least difficult level of play and “RANK D” being the most difficult level of play. See the “OPTION SWITCH SETTINGS" table.
  • To check “SOUND” (the game has 18 different sounds):
  • Move the controller to the right momentarily and release it — “SOUND” number changes from “00” to “01”,
  • Press any game play button or activate the coin switches and sound “01” is heard.
  • Repeat Step 6. a) — “SOUND 01” changes to “SOUND 02”.
  • Repeat Step 6. b) — and “SOUND 02” is heard.
  • To check your game function switches and buttons (coin counter switches, FIRE button, 7 PLAYER and 2 PLAYER buttons): activate each one while the game is in the Self-Test mode. You should hear the same sound during each activation. If you do not hear it, the switch/ button is either not working, miswired, or disconnected. Check it out thoroughly.
  • When finished with the Self-Test mode, slide the Self-Test switch back to the “OFF” position. e Across hatch pattern appears on the monitor screen for about 2 seconds. e If you wish to keep this test pattern on the monitor screen for further use, slide Self-Test switch back to the “ON” position after the cross hatch appears and before it disappears. When finished with the cross hatch pattern, set Self-Test switch to the “OFF” position. Normal game functions will now return to the monitor screen.

ATTRACT MODE

  • The Attract mode starts: e Just after power has been turned on to the game. (Self-Test switch is in the “OFF” Position.) e After a Self-Test has been completed. (Performing a Self-Test sets the credits in the games memory to zero “0”. e After a play has been finished, the score was not high enough to put the game into the High Score/Initial mode, and there are no more credits left in the games memory. e After the High Score/Initial mode when there are no more credits left in its memory.

READY-TO-PLAY MODE

1, The Ready-To-Play mode starts when enough coins have been accepted for a 1 or a 2 player game.

2-7

  • The Ready-To-Play mode ends when either the “4 PLAYER” or the “2 PLAYER” push button is pressed.

PLAY MODE

  • The Play mode begins when either the “1 PLAYER” or the “2 PLAYER” start button is Pressed. “PLAYER 1”, “STAGE 1” is displayed centered on the screen.
  • The Play mode ends when all of your space fighters have been destroyed. when this happens, “GAME OVER’ is written across the center of the monitor screen.
  • The game is made up of convoys of invading alien space ships. You, as defender, try to destroy as many convoys as you can.
  • The convoys are displayed one at a time at the top of the screen. They are made up of GALAGA COMMAND SHIPS, RED GALAGAS, and BLUE GALAGAS. These ships fly onto the screen from different angles, going by your position (giving you an opportunity to shoot them down) and then take up their positions in the convoy formation at the top of the screen. In the first STAGE, the enemy ships do not drop bombs on you as they fly onto the screen and go by your position. However, they will in later stages. After the convoy (or what's left of it after you've finished shooting at them as they fly onto the screen and head for their respective spots in the convoy formation) finishes forming up at the top of the screen, enemy ships will begin peeling off and diving at your fighter. They weave back and forth across the screen dropping bombs all the while. The GALAGA COMMAND SHIPS can put outa tractor beam and capture your fighter. When this happens, that fighter changes color from white to red and stays with that particular enemy COMMAND SHIP for the rest of the game. You can get your fighter back by destroying the GALAGA COMMAND SHIP that captured it while they are both attacking your current fighter. The GALAGA COMMAND SHIPS MUST BE SHOT TWICE to destroy them. When shot once, they change color from green to blue. When shot again, they explode. If, however, you mistakenly shoot the captured fighter, it will be destroyed. At that time, if the captured fighter is in a stand-by position in the convoy formation — 500 points will be added to your score; if the captured fighter is attacking — 1000 points will be added to your score. The RED and BLUE GALAGAS will explode as soon as they are hit by one of your shots.
Page 15

There are also special attack squadrons made up of three ships each which will appear from STAGE 4 on. If they are completely destroyed, bonus points will be awarded as follows:

STAGES 4-6 1000 BONUS POINTS STAGES 8-10 2000 BONUS POINTS STAGES 12-14 3000 BONUS POINTS When you destroy the last ship of a convoy, the screen gives the following display centered on the monitor screen: “STAGE ” (And the number of the next stage.) The only exception to this would be when the next STAGE is a CHALLENGING STAGE. The first CHALLENGING STAGE comes at the end of the 2nd STAGE. After this, they come at the end of every third STAGE. When you destroy the last ship of the 2nd, 6th, 10th, 14th, 18th, etc. convoys, you will see this display centered on the monitor screen: “CHALLENGING STAGE” A CHALLENGING STAGE is made up of 40 enemy ships that fly by your fighter in 5 groups of 8 ships each while describing varying patterns. They do not drop any bombs and the object is to shoot down as many of them as you can. When you shoot down one COMPLETE formation of 8 enemy ships, bonus points (between 1000 and 3000 depending on the STAGE) are added to your score. If you can destroy all 40 GALAGAS, you will be awarded a SPECIAL BONUS OF 10000 POINTS for that particular CHALLENGING STAGE. When you destroy all 40 GALAGAS, you will see this display centered on the monitor screen: “PERFECT !” — flashes “NUMBER OF HITS 40” “SPECIAL BONUS 10000 PTS”

Otherwise, after each CHALLENGING STAGE is over, the game gives this display centered on the monitor screen: NUMBER OF HITS _ ___ BONUS _ __ ____ (The BONUS is 100 times the NUMBER OF HITS.) The next display the game always gives is shown below and is centered on the monitor screen. “STAGE ” (And the number of the next stage.) As you destroy more convoys, the aitacks on you become faster, are in a more rapid succession, and follow trickier flight patterns. For instance, they will try to trap you ina cross fire, or in one corner of the screen, etc. You've really got to watch them closely. If they can’t bomb you, they'll ram you in the rear. That's one of their favorite tricks, to fly in a circle and come up behind you.

2-8 When the enemy happens to destroy one of your fighters, assuming you have at least one reserve fighter left, the word “READY” appears centered on the monitor screen BEFORE play begins again. When the enemy destroys or captures your last fighter, the words “GAME OVER” are displayed centered on the monitor screen. The next thing the game does is to display your “RESULTS” statistics. See the following sample display.

1UP HIGH SCORE *2 UP 000000 000000 000000 RESULTS SHOTS FIRED __— NUMBER OF CC HIT-MISS RATIO — —_, —% stage markers —] a “ONLY SHOWN IF THE LAST GAME WAS A TWO PLAYER GAME.

If your score was high enough to become one of the five best scores, the game will go into the High Score/Initial mode immediately after the Results mode. If your score is not high enough to cause the game to go into the High Score/Initia) mode, it will either go to the Attract mode (if there are no more credits left in its memory) or into the Ready-To-Play mode (if there are still credits left in its memory).

When in the High Score/Initial mode, there are three “As under the top “NAME” heading on the screen. The first “A” is yellow and flashing on and off. The other two “A”'s are white. Farther down the screen under the “TOP 5” heading, your score has been entered in bright yellow and the space for your initials is blank. All other scores are white. By moving the controller stick to the right, the flashing letter can be made to sequence forward through the alphabet: “A”, “B”, “C", “D”, etc. By moving the controller stick to the left, the flashing letter can be made to sequence backward through the alphabet: “Z”, “Y”, “x”, “W", etc. When you reach your initial, release the controller and push the FIRE button. Your initial is frozen in place and appears in the blank space opposite your score, just press the FIRE button three times. Three “A's will appear opposite your score. After the High Score/Initial mode, the game will either go to the Attract mode (if there are no more credits left in its memory) or into the Ready-To-Play mode (if there are still credits left in its memory. Most of the above holds true in the “2 PLAYER” mode also. But there are a few minor differences.

Page 16

TWO PLAYER OPERATION

The Upright, Mini, and Cocktail Table models all have two player operation. In the two player mode, the rules of play are the same as in the single player mode. There are some additional rules, however. 1. In the Upright and Mini models, the players must take turns at the controls. In the Cocktail Table model, each player has his own set of individual controls. The picture will flip to face you when it is your turn. (When it is not your turn, your set of controls will have NO effect on the game.) Your turn lasts until the enemy blows up your space fighter. At this point, the game will do one of several things depending on whether or not the destroyed fighter was your last or if you still have others remaining in reserve. FIGHTER DESTROYED — FIGHTERS REMAINING IN RESERVE The attack stops and the remainder of the enemy convoy flies off the top of the screen in formation. e@ Next, “PLAYER "= "STAGE ” is displayed (whenever a new convoy is going to come onto the screen) otherwise it just displays “PLAYER ” - “READY” while e Game displays “PLAYER © Next, it goes to the “RESULTS” mode. e After the “RESULTS” mode, if your score was what's left of the previously formed convoy flies onto the top of the screen. e Play begins for the other player.

FIGHTER DESTROYED OR CAPTURED — NO FIGHTERS REMAINING IN RESERVE

” = “GAME OVER”.

high enough, it goes to the “HIGH SCORE/ INITIAL” MODE. After this mode, the game will display “PLAYER ”"~“STAGE ” (whenever anew convoy is going to come onto the screen) otherwise it just displays “PLAYER ” “READY” while what's left of the previously formed convoy flies onto the top of the screen and play begins for the other player. \f your score was not high enough to cause the game to go into the “HIGH SCORE/ INITIAL” mode, the game will display “PLAYER "”-“STAGE ” (whenever anew convoy is going to come onto the screen) otherwise it just displays “PLAYER ” “READY” while what's left of the previously formed convoy flies onto the top of the screen and play begins for the other player.

2-9

Page 17

Il Maintenance and Repair

Page 18

Maintenance and Repair

Your GALAGA game needs certain types of maintenance to keep it in good working order. Clean, well maintained games aitract players and earn more profits, The most important thing for you to remember is to run the Self-Test EVERY TIME you collect money from the coin box. JUST LOOKING at your game WILL NOT tell you if all its controls and inside parts are working correctly. The Self-Test will inform you whether or not your game is working the way it should. The second most important thing you should remember is to clean the outside of the game and coin acceptor mechanisms on a regular basis.

CLEANING The outside of the game cabinet plus the metal can be cleaned with any non-abrasive household cleaner. However, the front of the T.V. monitor tube and both sides of ali other glass and plastic on or in the game MUST be cleaned with anti-static cleaner ONLY. For Cleaning the coin acceptors; hot soapy water may be used on the plastic ones and any household cleanser may be used on the metal ones. If you wish, special coin machine cleaners that leave no residue may be purchased from your distributor. DO NOT dry-wipe any of the plastic panels. This is because any dust that was on them can scratch their surfaces. If this has happened, anyone looking through this type of damaged plastic would feel he was looking at the game through a fog. This fogging damage CAN NOT be repaired or reversed.i The ONLY solution is to replace the damaged piece of plastic.

FUSE REPLACEMENT

  • UPRIGHT MODEL: As viewed from the back, facing the cabinet,

with the rear access door removed; the fuses are

located on the Mech. Panel and the Power Supply Board. . MINI MODEL: As viewed from the back, facing the cabinet,

located on the Mech. Panel and the Power Supply Board. . COCKTAIL TABLE MODEL: As viewed from the coin door side of the cabinet, with the monitor tilted open to one side; the fuses are located on the Mech. Panel and the Power Supply Board.

3-1 Replace fuses ONLY with the type and size listed in the Illustrated Parts Breakdown Section of this manual. See the T.V. Monitor Manual (available on request from your distributor or the monitor manufacturer) and/or the T.V. Troubleshooting Section of this manual for information on these fuses.

OPENING THE CONTROL PANEL.

  • UPRIGHT MODEL: e The control panel is held in place by three latches; one on the left side, one on the right side, and one in the center of the front of the cabinet. They are spring loaded to provide constant positive pressure on their latch plates. They can be reached through the coin door AFTER turning power to the game off. To release the latches, lift up and toward the center of the control panel. Once they are released, unhook them from their latch plates. To remove the control panel: Raise it up and tilt it toward you until you can see the cable behind it. Cradling the control panel between yourself and the cabinet, disconnect it from its cabling. The contro! panel is now free and can be removed. To reinstall the control panel, reverse this procedure.
  • MINI MODEL: © The control panel is held in place by two latches, one on the right side and one on the left side of the cabinet. They are spring loaded to provide constant positive pressure on their latch plates. They can be reached through the coin door AFTER turning power to the game off. To release the latches, lift up and toward the center of the contro! panel. Once they are released, unhook them from their fatch plates. To remove the control panel: Raise it up and tilt it toward you until you can see the cable behind it. Cradling the control panel between yourself and the cabinet, disconnect it from its cabling. The control panel is now free and can be removed.
Page 19

¢ To reinstall the control panel, reverse this procedure.

  • COCKTAIL TABLE MODEL: ¢ Each control panel is held in place by several screws, two on the inside of the cabinet and three along the outside bottom edge of the control panel. Turn power to the game off. Open the coin box door and release the two latches indicated in Figure 5.
CAUTION: The right hand latch is very close to the HIGH VOLTAGE on the monitor.

Once they're released, unhook them from their latch plates. Grasp the table top at “A” and open it as indicated in Figure 5.

CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet. Remove the screws which secure the control panel in place. To remove the control panel(s): Disconnect it from its cabling. The control panel is now free and can be removed. e To reinstall the control panel, reverse this procedure.

Figure 5. Opening

3-2 REMOVAL OF THE MAIN-DISPLAY- GLASS AND/OR THE T.V. BEZEL ASSEMBLY

  • UPRIGHT MODEL:
NOTE: To do this, the latches which secure the control panel MUST be released. The control panel need not be removed. See the “UPRIGHT MODEL” procedure. Turn the power to the game off and remove the rear access door. Remove the screws from the glass support bracket and lift it out the back of the cabinet. Grasp the main-display-glass in the top center, lift up slightly and pull it out the rear of the cabinet. Loosen the screws which secure the T.V. bezel-glass-clamps in piace. Move the clamps to the side and the bezel glass may be removed. Remove the above mentioned screws and the bezel with four bezel-glass-clamps may be removed. To reinstall the T.V. bezel assembly and the main-display-glass, reverse this procedure. MINI MODEL:
NOTE: In order to do this, the control panel MUST be removed first. See the “MINI MODEL” procedure. Turn the power off to the game and remove the control panel.

Cocktail game

Page 20

e Remove the screws which secure the glass clamping plate. Lift out the glass clamping plate. This frees the main-display-glass so it can be lifted up. e By putting your finger in the hole in the middle of the main-display-glass support, you can lift it up and out. e Remove the screws which secure the T.V. bezel assembly and lift it out.

NOTE: Use the hole in the center of the maindisplay-glass support to grasp it. e Reverse this procedure to reinstall the T.V. bezel assembly and the main-display-glass.
  • COCKTAIL TABLE MODEL:
NOTE: This may be done with the table top in the open or the closed position. If you decide to open the table top, TURN THE POWER TO THE GAME OFF FIRST. Remove the screws which secure the table top glass clamps in place. Remove the table top glass. Lift out the T.V. bezel assembly. To reinstall the T.V. bezel assembly and the table top glass, reverse this procedure.

T.V. MONITOR REPLACEMENT

CAUTION: High voltages may exist in any television unit, even with the power disconnected. Use EX- TREME CAUTION and do not touch electrical parts or the T.V. yoke, area with your hands or with metal objects held in your hands! In addition, BE SURE TO USE HEAVY GLOVES when handling the monitor. You could cut your hands on the metal T.V. chassis without such protection.
DANGER: The T.V. monitor DOES NOT contain an isolation transformer on its chassis (it is mounted instead on the floor of the cabinet). When servicing the monitor on a test bench, YOU MUST ISOLATE THE MONITOR FROM AC VOLTAGE WITH AN ISOLATION TRANS- FORMER.
  • UPRIGHT MODEL. SEE FIGURE 6 e Turn power off to the game. © Open the rear access door. e Completely disconnect the T.V. monitor from all its cabling. DON'T FORGET THE CHAS- SIS GROUND WIRE. Before removing the T.V. monitor, the maindisplay-glass and bezel must be removed. See above “Upright Model” procedure.

3-3 With the removal of only four bolts, the T.V. monitor and its mounting channels will be loose. The monitor mounting channels slide on top of and against two metal guides mounted to the cabinets right and left sides. The monitor is removed by sliding it out the back of the cabinet. To reinstall the T.V. monitor, be sure to run the game Self-Test.

REMOVE

  • BOLTS

= ae ka = es Pe

UPRIGHT

Figure 6. Removing monitor from Upright game

Page 21

MINI MODEL SEE FIGURE 7 Turn the power off to the game. Open the rear access door. Completely disconnect the T.V. monitor from ail its cabling. DON'T FORGET THE CHASSIS GROUND WIRE. Before removing the T.V. monitor, the maindisplay-glass and bezel must be removed. See above “Mini Model” procedure. With the removal of only four nuts, the T.V. monitor will be loose.

CAUTION: BE SURE to support the T.V. monitor from the rear while removing the four bolts so it will not fall out of the cabinet. The monitor is removed by supporting it and pulling straight back. To reinstall the T.V. monitor, procedure. After replacing the T.V. monitor, be sure to run the game Self-Test. . COCKTAIL TABLE MODEL: SEE FIGURE 8 Turn power off to the game. Open the coin box door and release the two latches indicated in Figure 5. reverse this
CAUTION: The right hand latch is very close to the HIGH VOLTAGE on the monitor.

© Once the latches are released, unhook them from their latch plates.

REMOVE

  • NUTS

Figure 7. Removing monitor from Mini game

3-4 e Grasp the table top at “A” and open it as indicated in Figure 5.

CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet.

Remove the screws which hold the table top glass clamps in place. e Remove the table top glass. © Lift out the T.V. bezel assembly. Completely disconnect the T.V. monitor from all its cabling. DON'T FORGET THE CHAS- SIS GROUND WIRE. @ Remove the screws holding the T.V. monitor chassis to the “L” by the door hinge(s). e Close the Cocktail Table top and re-latch it. e Remove the screws which secure the T.V. monitor mounting brackets to the edges of the slot cut in the table top. e Pry up the end of each monitor mounting bracket with a screwdriver or similar tool until you can grasp them both. e Lift the T.V. monitor straight up and out of the table top being VERY CAREFUL not to bump the neck of the picture tube. e To reinstall the T.V. monitor, reverse this procedure. e Be sure to check the clearance of the “L” brackets BEFORE setting the monitor into the table top. e After replacing the T.V. monitor, be sure to run the game Self-Test.

REMOVE 6 SCREWS (3 EACH SIDE) AND LIFT MONITOR

‘REMOVE 4 SCREWS (2 EACH SIDE)

Figure 8. Removing monitor from Cocktail game

Page 22

PRINTED CIRCUIT BOARD (P.C.B.) REPLACEMENT

1. UPRIGHT MODEL. SEE FIGURE 9 e Turn the power to the game off. e Unlock and open the rear access door. e Disconnect the video board from all its cabling. e Disconnect the CPU board from all its cabling. © Slide the P.C.B. clamps to one side, remove the P.C.B.'s from the card rack and take them out the back of the cabinet. e Disconnect the power supply board from all its cabling, remove the P.C.B. supports indicated in Figure 10, and slide it out the back of the cabinet. e To reinstall the above P.C.B.’s, reverse this procedure.

NOTE: P.C.B.'s are all keyed and will ONLY fit into their connectors one way without forcing them. The plugs on the cable harness which connect it to the P.C.B.'s are also keyed and will ONLY go onto their connectors one way with out forcing them.
  • MINI MODEL. SEE FIGURE 9 e Turn the power off to the game. @ Unlock and open the rear access door. e Disconnect the video board from all its cabling. e Disconnect the CPU board from all its cabling. Slide the P.C.B. clamps to one side, remove the P.C.B.’s from the card rack and take them out the back of the cabinet. e Disconnect the power supply board from all its cabling, remove the P.C.B. supports indicated in Figure 9, and slide it out the back of the cabinet. © To reinstall the above P.C.B.’s, reverse this Procedure.

COCKTAIL TABLE MODEL. SEE FIGURE 9. e Turn the power off to the game. e Open the cabinet: Open the coin box door and release the two latches indicated in Figure 5.

CAUTION: The right hand latch is very close to the HIGH VOLTAGE on the monitor. e@ Once they’re released, unhook them from their latch plates. @ Grasp the table top at “A” and open it as indicated in Figure 5.
CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet.

3-5 e To remove the power supply board. Disconnect it from all its cabling. Remove the two smallest P.C.B. supports. Once these are removed, the power supply can-be lifted out the top of the cabinet. To reinstall the power supply board, reverse this procedure. e To remove the video and CPU boards. Disconnect the video board from all its cabling Disconnect the CPU board from all its cabling. Slide the P.C.B. clamps to one side, rémove the P.C.B.’s from the card rack and liftthem out the top of the cabinet. To reinstall the video and CPU boards, reverse this procedure.

OPENING THE ATTRACTION PANEL

  • UPRIGHT MODEL

e Turn the power to the game off. e@ Opening the attraction panel: Remove the screws which secure the top bracket in place. (They are on its top side.) Remove the top bracket and slide up the attraction panel. This exposes the attraction panel fluorescent light tube and its mounting bracket assembly. To reinstall the attraction panel, reverse this Procedure. e The fluorescent light tube may be replaced at this time. BE CAREFUL NOT TO DROP IT.

WARNING: If you drop a fluorescent tube and it breaks, IT WILL IMPLODE! Shattered glass can fly six (6) feet or more from the implosion. Use care when replacing any fluorescent tube.

e Replacing the fluorescent tube starter. Be sure the power to the game has been turned off.

Page 23

POWER SUPPLY P.C.B.

| an Ry © Tag

REMOVE THE REMOVE rm | SUPPORT TO SLIDE P.C.B. OUT MINI SUPPORT TO SLIDE P.C.8.0UT —YPRIGHT POWER SUPPLY P.C.B.

REMOVE (2) SUPPORTS TO SLIDE P.C.B. UP

COCKTAIL POWER SUPPLY P.C.B.

Figure 9. P.C.B. replacement

3-6

Page 24

Grasp the starter (it is on the back of the mounting bracket), give it a quarter turn, and remove it from its socket. To replace the fluorescent light tube starter, reverse this procedure. © Replacement of the fluorescent tube mounting bracket assembly. Be sure the power is off to the game. Disconnect it from its power cable. Remove the screws at its right and left hand sides which secure it and gently slide it out the front of the cabinet, being careful not to catch its power cable on anything. To reinstall the fluorescent tube mounting bracket assembly, reverse this procedure. © Replacing the speaker. Be sure the power is off to the game. Remove the attraction panel and disconnect the speaker from its cabling. Remove the nuts and bolts which secure the speaker and speaker grill in place and set them and the speaker grill aside. Once the bolts which secure the speaker in Place are removed, the speaker may be removed through the opening where the attraction panel was. Reverse this procedure to reinstall the speaker.

  • MINI MODEL. Turn the power off to the game. e@ Remove the screws from the top and bottom of the formed attraction panel. e Remove the formed attraction panel by pulling It straight away from the cabinet. This exposes the attraction panel light bulbs and their mounting board. © To service the light bulbs and their mounting board: Turn the power to the game back on so you can see which bulbs are burnt out. Mark the burnt out bulbs and turn the power to the game back off again. To replace the burnt out bulbs, grasp them gently and pull straight out. The new bulbs are gently pushed into the empty sockets. To completely replace the light bulb mounting board: Open the cabinet rear access door and unplug the mounting board from its power cable. Remove the screws that hold the mounting board to the cabinet. Gently slide the mounting board out the front of the caginet being careful not to catch its cable on anything.

3-7 To reinstall the above removed items, reverse this procedure. To replace the speaker. Be sure the power is off to the game. Disconnect the speaker from its cabling. Remove the nuts and bolts securing the speaker. Slide the speaker out through the rear access door. To reinstall the speaker, simply reverse this procedure.

  • THE COCKTAIL TABLE MODEL HAS NO BACK-LIT ATTRACTION PANEL.

COIN DOOR MAINTENANCE:

METAL COIN ACCEPTOR MECHANISMS Periodically, the metal coin acceptor mechanism(s) must be removed from the coin door and cleaned. Make sure the power to the game is off.

Unlock and open the coin door. Remove the coin acceptor mechanism. 1.

2.

3.

4.

a Push down on the two spring loaded latches. While holding the latches down, pull the top of the coin acceptor mechanism toward you. Release the latches and lift out the coin acceptor mechanism. Clean the magnet of all foreign particles: See Figure 10. This may be accomplished by swinging the gate open as shown in the above figure. Remove the cradies and undersize levers and clean the bushings. (A pipe cleaner makes a good bushing cleaner. Also clean the pivot pin. Whenever needed, the coin acceptor should be cleaned with hot water and cleanser in the following manner: e Place the coin acceptor in boiling water for about ten minutes.

CAUTION BE CAREFUL NOT TO BURN YOURSELF.

Next, use a brush and kitchen cleaner to remove all remaining foreign matter from the unit. Rinse the coin acceptor in clean boiling water. Dry the coin acceptor thoroughly by using filtered compressed air to blow it dry.

Page 25
NOTE:
WARNING The reason we recommend using boiling water is DO NOT USE OIL that it evaporates faster than cold water and TO LUBRICATE THE speeds the drying time. COIN ACCEPTOR.
  • Check the coin chute for obstruction such as:
  • To lubricate the coin acceptor: Eetet gum, ete. | e Use ONLY powdered graphite and put it 9. Reinstall the coin acceptor to the coin door. ONLY on the moving parts of the coin e Place the two pegs at the coin acceptors base acceptor. These parts are called out in Figure into their retaining slots.
  • © Now push the top of the coin acceptor toward e Be extremely careful to keep the powdered the coin door until it snaps in place and is held graphite away from paths that are traveled by there by the two spring loaded latches. the coins. 10. Close and lock the coin door.

APPLY POWDERED GRAPHITE HERE

UNDERSIZE LEVER

“E” RINGS

GATE OPEN AS SHOWN CLEAN MAGNET BY DRAGGING A SCREWDRIVER BLADE ACROSS SURFACE

Figure 10. Opening the metal coin acceptor Figure 11. Lubricating the metal coin acceptor

3-8

Page 26

PLASTIC COIN ACCEPTOR MECHANISMS The plastic coin acceptor mechanismm(s) must be removed periodically from the coin door and cleaned.

  • Make sure the power to the game is off.
  • Unlock and open the coin door.
  • Remove the coin acceptor mechanism(s). e Push down on the two spring loaded latches. @ While holding the latches down, pull the top of the acceptor mechanism toward you. e Release the latches and lift out the mechanism.
  • Squeeze the two pins on the mechanisms together to open and break it down into its three basic parts. e Clean the mechanism in hot soapy water. It never rusts. « Rinse the mechanism in clean hot water and allow it to dry. e Reassemble the mechanism (it never needs lubrication).
  • Check the coin chute for obstructions such as: paper, gum, etc.
  • Reinstall the coin acceptor to the coin door. e Place the two pegs at the coin acceptors base into their retaining slots. Now push the top of the coin acceptor toward the coin door until it snapsin place and is held there by the two spring loaded latches.
  • Close and lock the coin door.
NOTE: See Figure 12 for instructions on how to set the plastic coin acceptor mechanisms to either accept or reject Canadian quarters.

ACCEPTOR CAN BE SET TO ACCEPT U.S. QUARTERS ONLY OR BOTH U.S. AND CANADIAN QUARTERS.

SLIDE MAGNET TO EXTREME RIGHT (AS SHOWN) TO ACCEPT BOTH U.S. AND CANADIAN QUARTERS.

TO ACCEPT U.S. QUARTERS ONLY, SLIDE MAGNET TO ~—_______ EXTREME LEFT.

Figure 12. Changing the plastic coin acceptor for American or Canadian Quarters

Page 27
Scan of page 27

This page is a drawing, shown as the original scan.

Page 28

GALAGA — CONTROL ASSEMBLY — ALL VERSIONS

—~ ~~ GALAGA — CONTROL ASSEMBLY — ALL VERSIONS ORDER BY PART NUMBER ONLY

PART NO. DESCRIPTION

A866-00207-0000 MOLDED 1-3/8" DIA. BALL & SHAFT ASSY. 0017-00100-0025 1/4" E-RING 0852-00106-0000 FOLLOWER PLATE A508-00021-00XF TOP PLATE — MAIN CONTROL BRKT. ASSY. 0017-00041-0616 RUBBER BUMPER — 90 DUROMETER (2 REQ’D.) A866-00027-0000 PIVOT BRKT. HUB & BEARING ASSY. 0852-00701-00XF PIVOT PIN 0017-00103-0011 #10-32 LOCK NUT 0508-001 12-00XF BRACE — MAIN BRKT. 0017-00101-0755 #6-32 x 5/16 SLT. PAN HD. M.S. (4 REQ’D.) 0017-00101-0620 #8-32 x 1/2 RND. CARRIAGE BOLT (4 REQ'D.) 0017-00103-0061 #8-32 LOCK NUT W/SEMS (4 REQ'D.) 0852-00103-00XF SWITCH BRKT. (2 REQ’D.) A508-00022-0000 LEAF SWITCH ASSY. (2 REQ'D.) 0020-00202-0000 SWITCH PLATE (2 REQ'D.) 0017-00101-0737 #5-40 x 5/8 SLT. PAN HD. M.S. (4 REQ’D.)

Page 29

FRONT DOOR ASSEMBLY — U.S.A. 25¢

Page 30

CHWONAKDAONMA= PART NO. FRONT DOOR ASSEMBLY — U.S.A. 25¢

ORDER BY PART NUMBER ONLY

DESCRIPTION

0090-00002-02BK 0017-00101-0121 A090-00073-02BK 0017-00101-0123 0017-00007-0019 0017-00101-0552 0090-00117-03XF A097-00005-0000 A097-00006-0000 0090-00128-00XF 0017-00005-0041 090-0007 1-0000 0090-001 26-01XF 0017-00101-0528 A090-00004-0000 0090-00903-9500 0090-00143-00XF 0017-00003-0052 0017-0003 1-0038 0017-00104-0002 0017-00103-0087 A090-00057-0000 0017-00101-0124 0017-00032-0051 0017-00032-0007 0017-0007 2-0034 0090-00173-0000 A090-00082-0000 A090-00087-0000 0010-00134-0000 0010-00181-0000 0017-00007-0083 0090-00129-00XF 0090-00167-O0XF 0093-00155-00XF 0017-00100-0018 A090-00088-0000 A090-00085-0000 0017-00005-0003 0017-00005-0211 0017-00005-0214 A090-00064-0000 0017-00101-0099 0090-00162-00XF 0017-00005-0203 0017-00005-0195 0010-00599-0000 0017-00007-0132 A090-00059-0400 0017-00101-0698 A090-00077-0000 DOUBLE ENTRY COIN DOOR FRAME #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ’D.) DOUBLE ENTRY COIN DOOR W/DRESS PLATE #8 x 1/4 UNSLOT. HEX HD. SCREW (4 REQ'D.) KEY HOOK #6-32 x 1/4 CARRIAGE BOLT (4 REQ’D.) COIN ENTRY PLATE — 25¢ (2 REQ’D.) DOOR LOCK & KEY W/SCREW & NUT (OR) DOOR LOCK & KEY W/SCREW & NUT DOOR TILT SWITCH BRKT. DOOR CAM DOOR TILT SWITCH SWITCH BACK-UP PLATE #5-40 x 3/4" PHIL. HD. M.S. (2 REQ’D.) DOOR TILT SWITCH & BRKT. ASSY. (ITEMS 9 & 11 THRU 13) 25¢ WINDOW (2 REQ'D.) COIN PLEX RETAINER 12 VOLT LAMP — G.E. #1895 (2 REQ’D.) BAYONET SOCKET W/BRKT. (2 REQ'’D.) #6 SPLIT LOCK WASHER (8 REQ’D.) #6-32 HEX NUT (8 REQ'D.) COIN METER #6 x 1/4 UNSLOT. HEX HD. SCR. (8 REQ’D.) PUSH BUTTON SWITCH SLIDE SWITCH STEEL OVAL HD. RIVET COIN COUNTER MTG. BRKT. TEST SWITCH & BRKT. ASSY. (ITEMS 23 THRU 25) COIN CHUTE & TOP ASSY. (2 REQ’D.) SPRING SPRING 1/8 x 1-5/8 ROLL PIN PIVOT POST PIVOT LEVER REJECT LEVER E-RING REJECT LEVER ASSY. (2 REQ’D.) (ITEMS 30 THRU 33) COIN ACCEPTOR FRAME ASSY. (2 REQ’D.) COIN ACCEPTOR W/STRING CUTTER (2 REQ’D.) (OR) COIN ACCEPTOR W/ANTI STRING DEVICE (2 REQ’D.) (OR) COIN ACCEPTOR W/STRING CUTTER (2 REQ’D.) ANTI-PENNY DEVICE #6 x 1/4 SLT. HEX HD. M.S. (2 REQ'D.) COIN SWITCH MTG. BRKT. COIN SWITCH CHUTE COIN SWITCH COIN SWITCH WIRE PUSH-ON RING COIN SWITCH & WIRE ASSY. (ITEMS 40 THRU 42) #4-40 x 3/4 SLT. RND. HD. M.S. (2 REQ'D.) COIN GUIDE & SWITCH ASSY. (ITEMS 38 THRU 43)

4-3

Page 31

GALAGA — CARD RACK ASSY. W/BOARDS — ALL VERSIONS

4-4

Page 32

GALAGA — CARD RACK ASSY. W/BOARDS — ALL VERSIONS

ORDER BY PART NUMBER ONLY

PART NO. DESCRIPTION

A084-91404-C508 CPU BOARD ASSY. A084-91405-B508 VIDEO BOARD ASSY. A935-00015-0000 HOLDER PLATE & STOP ASSY. (2 REQ'D.) 0017-00009-0478 NYLON GUIDE (4 REQ’D.) 0508-001 16-0100 P.C. SUPPORT BRKT. — RIGHT 0508-001 16-0200 P.C. SUPPORT BRKT. — LEFT 0935-00103-0000 SIDE SUPPORT (2 REQ’D.) 0935-00102-0000 MOUNTING BRACKET (2 REQ’D.) 0017-00101-0096 #6 x 3/8 SLT. HEX HD. SCR. (14 REQ’D.) ONAnNKHAwWNMYA

GALAGA — TRANSFORMER BOARD ASSY. — PARTS LIST

ORDER BY PART NUMBER ONLY

MT00-00082-0000 TRANSFORMER — 115/115V. MT00-00087-0000 POWER TRANSFORMER — 120/240V. MT00-00085-0000 TRANSFORMER — 115V., 50 Hz — (COCKTAIL ONLY) MT00-00091-0000 SHIELDED TRANSFORMER 115/220V. — (COCKTAIL ONLY) 0017-00101-0628 #8-32 x 3/4 CARRIAGE BOLT (4 REQ’D.) 0017-00103-0008 #8-32 HEX NUT (4 REQ’D.) 0017-00101-0014 #6 x 1/2 SLT. HEX HD. M.S. (15 REQ'D.) 0720 -00001-0300 3 POSITION FUSE CLIP ASSY. (U.R. & COCKTAIL ONLY) 0720-00001-0200 2 POSITION FUSE CLIP ASSY. (MINI ONLY) 0720-00001-0100 1 POSITION FUSE CLIP ASSY. 0017-00003-0004 SLO-BLO FUSE — 2 AMP, 250V. (2 REQ’D.) 0017-00003-0002 SLO-BLO FUSE — 1/2 AMP, 250V. (COCKTAIL & U.R. ONLY) 0017-00003-0217 SLO-BLO FUSE 2-1/2 AMP, 125V. 0017-00003-0114 NOISE FILTER 3010-13106-0000 TERMINAL STRIP 3000- 17143-0300 GROUND STRAP ASSY.

Page 33

NO. 508 — GALAGA UPRIGHT — FRONT

@®)

@) @) ©) (8)

@)

qn)

4-6

Page 34

NO. 508 — GALAGA UPRIGHT — FRONT PARTS LIST

ORDER BY PART NUMBER ONLY PART NO. DESCRIPTION 0508-00903-00XF | UPPER DECORATIVE PLEX! — 23” x 9-1/16" x 3/16” 0537-00903-0055 GLASS CHANNEL — 7-3/4" LG. (2 REQ'D.) 0508-00104-00XF | UPPER/LOWER HEADER RETAINER (2 REQ'D.) 0017-00101-0138 |- #8 x 5/8 TORX TAMPER RESISTANT BLK. SCR. (6 REQ’D.) 0017-00009-0522 LONG ARM KEY T-20 (FOR ABOVE SCREW) A508-00007-0000 | HEADER FLUORESCENT LIGHT ASSY. 0017-00009-0393 SPEAKER GRILL — BLACK W/SLOTS 0017-00003-0259 | 6” x 9" SPEAKER 8 OHM, 7W. 0017-00101-0127 | #8-32 x 1-1/2 CARRIAGE BOLT (4 REQ’D.) 0017-00103-0061 #8- 32 HEX NUT W/SEMS (4 REQ’D.) 0508-00900-0000 19” T.V. BEZEL 0508-00905-0000 | T.V. PLEXI-GLASS (GRAYLITE #31) — 17-3/8" x 13-1/4" x 1/8” 0508-00901-0000 PLEXI-GLASS CLIPS ( 4 REQ’D.) 0017-00101-0017 | #6 x 1/2 SLT. HEX HD. BLK. SCR. (4 REQ’D.) 0508-00902-00XF } MAIN DISPLAY GLASS — 23” x 21-1/8" x 3/16” 0508-00108-0000_} GLASS STOP BRKT. 0017-00101-0027 | #8 x 3/4 SLT. HEX HD. M.S. (3 REQ’D.) 0508-00904-0000 DECAL — SIDE (2 REQ’D.) 0508-00906-0000 DECAL — FRONT A508-00009-0000 | CONTROL PLATE & OVERLAY ASSY. A508-00028-0000 | CONTROL SHELF PLATE & STRIKE ASSY. 0508-00907-0000 CONTROL SHELF OVERLAY — DECORATIVE 0017-00101-0620 | #8-32 x 1/2 CARRIAGE BOLT (4 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (4 REQ’D.) 0961-00115-00xF | STRIKE (2 REQ'D.) 0508-00115-0000 CENTER CONTROL SHELF LOCK BRKT. 0017-00009-0033 BASSICK CLAMP (3 REQ’D.) 0508-00109-0100 CONTROL SHELF SUPPORT BRKT. — RIGHT 0508-00109-0200 CONTROL SHELF SUPPORT BRKT. — LEFT A508-00011-0000 | CONTROL ASsyY. 0017-00042-0256 PUSH BUTTON ASSY. — RED 0017-00042-0257 PUSH BUTTON ASSY. — YELLOW (2 REQ’D.) 0017-00032-0093 PUSH BUTTON SWITCH W/HOLDER (3 REQ’D.) 0017-00103-0054 | 5/8-11 PAL NUT (3 REQ’D.) A090-00300-07BK | U.S.A. 25¢ COIN DOOR ASSY. 0090-00002-028K | LARGE COIN DOOR FRAME 0017-00101-0121 #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ'D.) (MOUNTS COIN DOOR TO FRAME) 0935-00906-0100 KICK PLATE — 23” LG. 0017-00102-0048 | 3/8-16 x 2” LEG LEVELERS (4 REQ’D.) 0017-00103-0026 | 3/8-16 LEG LEVELER HEX NUTS (4 REQ’D.)

Page 35

4-8 NO. 508 — GALAGA UPRIGHT — REAR ACCESS

Page 36

NO. 508 — GALAGA UPRIGHT — REAR ACCESS PARTS LIST ORDER BY PART NUMBER ONLY

A088-00013-0000 | ON-OFF SWITCH & BRKT. ASSY. 0894-00913-0000 RECESSED HAND LIFT (2 REQ’D.) 0017-00101-0117 #8 x 5/8 PHIL. TRS. HD. SCR. (12 REQ’D.) 0017-00003-0339 ELECTROHOME — 19” COLOR DUAL SYNC. HORIZ. MTG. MONITOR (OR) 0017-00003-0401 WELLS-GARDNER — 19” COLOR DUAL SYNC. HORIZ. MTG. MONITOR A508-00005-0000 | MONITOR MTG. CHANNEL ASSY. (2 REQ'’D.) 0017-00102-0066 1/4-20 x 3/4 UNSLOT. HEX HD. BOLT (4 REQ’D.) 0508-00100-0000 MONITOR RAIL (2 REQ’D.) 0017-00102-0002 1/4-20 x 1/2 SLT. HEX HD. BOLT (4 REQ'D.) 0017-00104-0014 7/8” DISH WASHER (8 REQ’D.) 0508-00106-0000 BEZEL MTG. BRKT. (2 REQ’D.) 0508-00900-0000 T.V. BEZEL A151-00027-0000 | INTERLOCK SWITCH ASSY. A084-91414-C935 | POWER SUPPLY ASSY. 0624-00902-0100 P.C. SUPPORT BRKT. — 12” LG. (2 REQ’D.) 0624-00902-0300 P.C. SUPPORT BRKT. — 2-1/2" LG. 0624-00902-0500 P.C. SUPPORT BRKT. — 6-1/2" LG. 0017-00101-0025 #8 x 1/2 SLT. HEX HD. SCR. (10 REQ’D.) 0017-00104-0037 #8 FLAT WASHER (10 REQ’D.) A508-00019-0000 | CARD RACK W/P.C, BOARDS ASSY. A508-00013-0000 | TRANSFORMER BAD. ASSY. A084-91408-B508 | FILTER BOARD ASSY. (NOT SEEN) A961-00007-0000 | CASTER ASSY. (2 REQ’D.) 0961-00109-0000 WHEEL BRKT. (2 REQ’D.) 0017-00042-0255 PLASTIC WHEEL (2 REQ’D.) 0894-00702-00xF | SHAFT (2 REQ’D.) 0017-00100-0037 3/8" E-RING (2 REQ'D.) A866-00049-0000 | LINE CORD ASSY. ADDITIONAL PARTS LIST A082-91109-A000 CREDIT MULT. BYPASS P.C. BRD. A097-00001-0000 BACK DOOR LOCK ASSY. 0017-00009-0490 5-5/8 SQ. VENT GRILL — BACK DOOR (4 REQ’D.) A508-00014-0000 HIGH VOLTAGE CABLE ASSY. A508-00026-0000 COIN DOOR CABLE ASSY. A508-00015-0000 LOW VOLTAGE CABLE ASSY. A508-00016-0000 MASTER CABLE ASSY. A508-00035-0000 MONITOR SIGNAL ADAPTOR CABLE ASSY. A508-00018-0000 CONTROL SHELF CABLE ASSY. A508-00034-0000 AUDIO ADAPTOR CABLE ASSY. A508-00024-0000 SIGNAL CABLE ASSY. 0017-00009-0477 MOLDED CASH BOX A961-00008-0000 CASH BOX COVER ASSY. A894-00024-0000 CASH BOX SIDE CHANNEL ASSY. 0894-00121-0000 CASH BOX SIDE CHANNEL -- LONG 0017-00101-0628 #8-32 x 3/4 CARRIAGE BOLT (4 REQ'D.) 0017-00104-0022 #8 FLAT WASHER (4 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (4 REQ'D.) 3000-17143-0000 GROUND STRAP. A082-91410-A000 RAPID FIRE P.C. BRD. ASSY.

4-9

Page 37

NO. 508 — GALAGA UPRIGHT — HEADER FLUORESCENT FIXTURE ASSY.

4-10

Page 38

NO. 508 — GALAGA UPRIGHT — HEADER FLUORESCENT FIXTURE ASSY.

ORDER BY PART NUMBER ONLY

ITEM PART NO. DESCRIPTION

0508-00103-0000 FLUORESCENT BRKT. 0017-00003-0043 18" COOL WHITE FLUOR. LAMP 0017-00021-0005 FLUORESCENT LOCKS (2 REQ'D.) 0017-00031-0036 FLUORESCENT SOCKET (2 REQ’D.) 0017-00003-0412 FLUOR. STARTER HOLDER W/WIRE LEADS 0017-00101-0573 #6-32 x 1/2 PHIL. RND. HD. M.S. (4 REQ’D.) 0017-00104-0009 #6 EXT. WASHER (4 REQ’D.) 0017-00003-0019 FLUOR. STARTER 0017-00003-0026 BALLAST 0017-00101-0598 #8-32 x 5/16 SLT. HEX HD. SCR. (4 REQ’D.) A508-00017-0000 FLUORESCENT CABLE ASSY.

4-11

Page 39

NO. 514 — GALAGA MINI-FRONT

4-12

Page 40

NO. 514 — GALAGA MIN! — FRONT PARTS LIST

ORDER BY PART NUMBER ONLY

0514-00901-00xF | DISPLAY PANEL 0017-00101-0138 | #8 x 5/8 TORX TAMPER RESISTANT SCA. (8 REQ’D.) 0017-00009-0522 LONG ARM KEY T-20 (FOR ABOVE SCREW) A926-00010-0000 | INSERT DISPLAY ASSY. 0017-00031-0030 | WEDGE BASE LIGHT SOCKET (5 REQ’D.) 0017-00003-0219 | #194 LAMP 14V., .27A. (5 REQ’D.) 0017-00009-0393 | BLACK SPEAKER GRILL W/SLOTS 0017-00003-0187 | 6” x 9” SPEAKER 8 OHM, 9W. 0017-00101-0127 | #8-32 x 1-1/2 CARRIAGE BOLT (4 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (4 REQ’D.) 0514-00900-00xF | FRONT GLASS — 17-13/16" x 14-13/16" x 3/16" 0905-00903-0100 | GLASS EDGE CHANNEL — 14-1/2 LG. (2 REQ’D.) A93+-00012-0000 | GLASS CLAMPING PLATE ASSY. 0017-00101-0138 | #8 x 5/8 TORX TAMPER RESISTANT SCREW (2 REQ’D.) A514-00008-0000 | CONTROL PLATE & OVERLAY ASSY. 0514-00700-0000 | CONTROL SHELF PLATE 0514-00902-0000 | DECORATIVE SHELF OVERLAY 0017-00101-0620 | #8-32 x 1/2 CARRIAGE BOLT (4 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (4 REQ’D.) 0514-00102-0100 | CONTROL SHELF BRKT. SUPPORT — RIGHT 0514-00102-0200 | CONTROL SHELF B RKT. SUPPORT — LEFT 0961-00115-00XF | STRIKE (2 REQ'D.) 0017-00009-0033 BASSICK CLAMP (2 REQ’D.) A508-00011-0000 | CONTROL ASSY. 0017-00042-0256 PUSH BUTTON ASSY. — RED 0017-00032-0093 PUSH BUTTON SWITCH W/HOLDER 0017-00103-0054 5/8-11 PAL NUT 0017-00032-0051 SMALL RED SWITCH BUTTON W/HARDWARE (2 REQ’D.) A090-00300-07BK | U.S.A. 25¢ COIN DOOR ASSY. 0090-00002-02BK | LARGE COIN DOOR FRAME 0017-00101-0121 #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ’D.) (MOUNTS COIN DOOR TO FRAME) 0017-00102-0048 3/8-16 x 2" LEG LEVELERS (4 REQ’D.) 0017-00103-0026 3/8-16 LEG LEVELER NUTS (4 REQ’D.) 0935-00906-0400 KICK PLATE 17-15/16" LG. — NOT SHOWN

4-13

Page 41

4-14 NO. 514 — GALAGA MINI — REAR ACCESS

Page 42

NO. 514 — GALAGA MINI — REAR ACCESS PARTS LIST ORDER BY PART NUMBER ONLY

0017-00003-0187 0017-00003-0340 DESCRIPTION ITEM

6" x 9” SPEAKER 8 OHM, 9W. ELECTROHOME — 13” COLOR DUAL SYNC. HORIZ. MTG. MONITOR (OR) WELLS-GARDNER — 13” COLOR DUAL SYNC. HORIZ. MTG. MONITOR T.V. MTG. BRKT. ASSY. 1/4-20 x 3/4 UNSLOT. HEX HD BOLT (2 REQ’D.) 0017-00003-0369

A926-00012-O0XF 0017-00102-0066 0017-00104-0014 A514-00004-0000 0513-00900-0000 0934-00905-0000 A961-00026-0000 A151-00027-0000 7/8" DISH WASHER (2 REQ’D.) T.V. BEZEL ASSY. T.V. BEZEL PLEXI-GLASS (TINTED) BEZEL MTG. BRKT. ASSY. INTERLOCK SWITCH ASSY. A090-00300-07BK A084-91414-C935 0624-00902-0100 0624-00902-0300 0017-00101-0025 0017-00104-0037 A508-00019-0000 A084-91408-B508 A514-00010-0000 DOUBLE ENTRY COIN DOOR ASSY. POWER SUPPLY ASSY. P.C. SUPPORT BRKT. — 12” LG. (2 REQ'D.) P.C. SUPPORT BRKT. — 2-1/2" LG. (2 REQ'D.) #8 x 1/2 SLT. HEX HD. SCR. (10 REQ'’D.) #8 FLAT WASHER (10 REQ’D.) CARD RACK ASSY. W/BOARDS FILTER BOARD ASSY. — NOT SEEN TRANSFORMER BOARD ASSY. — (NOT SEEN) (LOCATED ON CABINET BASE) ON-OFF SWITCH & BRKT. ASSY. 5-5/8" SQ. VENT GRILL (4 REQ’D.)

ADDITIONAL PARTS LIST BACK DOOR LOCK ASSY. PROTECTIVE BUBBLE — BACK DOOR #8-32 x 3/4 CARRIAGE BOLT (10 REQ’D.) #8-32 HEX NUT W/SEMS (10 REQ’D.) CASH BOX ASSY. W/HANDLE CASH BOX COVER ASSY. CASH BOX SIDE CHANNEL ASSY. CASH BOX SIDE CHANNEL — LONG #8-32 x 3/4 CARRIAGE BOLT (4 REQ’D.) A088-00013-0000 0017-00009-0490

A097-00008-0000 0926-00904-0000 0017-00101-0628 0017-00103-0061 A905-00028-0000 A961-00008-0000 A894-00024-0000 0894-00121-0000 0017-00101-0628 0017-00104-0022 0017-00103-0061 AS08-00026-0000 514-0001 1-0000 A514-00012-0000 A514-00013-0000 A514-0001 4-0000 A514-00015-0000 A514-00024-0000 A508-00034-0000 A508-00035-0000 A866-00049-0000 A082-91109-A000 3000-17143-0000 A082-91410-A000 #8 FLAT WASHER (4 REQ'D.) #8-32 HEX NUT W/SEMS (4 REQ’D.) COIN DOOR CABLE ASSY. HIGH VOLTAGE CABLE ASSY. LOW VOLTAGE CABLE ASSY. MASTER CABLE ASSY. CONTROL SHELF CABLE ASSY. DISPLAY INSERT CABLE ASSY. SIGNAL CABLE ASSY. AUDIO ADAPTOR CABLE ASSY. MONITOR SIGNAL ADAPTOR CABLE ASSY. LINE CORD ASSY. CREDIT MULT. BYPASS P.C. BRD. GROUND STRAP RAPID FIRE P.C. BRD. ASSY.

4-15

Page 43

4-16 NO. 510 — GALAGA COCKTAIL — FRONT

Page 44

NO. 510 — GALAGA COCKTAIL — FRONT PARTS LIST

PART NO.

0510-00900-00XF 0775-00104-00XF 0017-00101-0117 A927-00022-0000 0927-00903-0000 0869-00907-0000 A510-00006-0100 A501-00006-0000 0017-00009-0393 0017-00003-0259 0017-00101-0136 0017-00103-0061 A090-00300-06BK 0090-00002-02BK 0017-00101-0121 ITEM

on

0017-00102-0048 0017-00103-0026

A927-00019-0000 A962-00004-0000 A962-00005-0000 0962-00101-0000 0017-00101-0628 0017-00104-0022 0017-00103-0061 A927-00008-0000 A151-00078-0000 A775-00013-0000 0151-00081-0000 0775-00110-00XF 0749-001 06-00XF 0017-00101-0347 0017-00104-0009 0017-00103-0005 0017-00101-0026 A866-00049-0000 3000-17143-0000 0927-00907-0000 ORDER BY PART NUMBER ONLY

DESCRIPTION

COVER GLASS — 32" x 22" x 1/4 GLASS CLIPS (8 REQ'D.) #8 x 5/8 PHIL TRS. HD. SCR. (16 REQ’D.) T.V. BEZEL & PLEX! ASSY. T.V, BEZEL GREY PLEX! CONTROL SHELF ASSY. — PLAYER #2 CONTROL SHELF ASSY. — PLAYER #1 BLACK SPEAKER GRILL W/SLOTS (3 REQ’D.) 6" x 9" SPEAKER 8 OHM, 7W. #8-32 x 1-1/4 CARRIAGE BOLT (12 REQ'D.) #8-32 HEX NUT W/SEMS (12 REQ’D.) DOUBLE ENTRY COIN DOOR ASSY. LARGE COIN DOOR FRAME #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ'D.) (MOUNTS COIN DOOR TO FRAME) 3/8-16 x 2” LEG LEVELERS (4 REQ’D.) 3/8-16 LEG LEVELER NUTS (4 REQ’D.) NOT SHOWN LIST COIN BOX ASSY. COIN BOX COVER ASSY. COIN BOX SIDE CHANNEL ASSY. — SHORT COIN BOX SIDE CHANNEL — SHORT #8-32 x 3/4 CARRIAGE BOLT (4 REQ'D.) #8 WASHER (4 REQ’D.) #8-32 HEX NUT W/SEMS (4 REQ’D.) ON/OFF SWITCH ASSY. INTERLOCK SWITCH ASSY. FAN ASSY. 4” MUFFIN FAN FAN PLATE FAN SCREEN #6-32 x 1/2 R.H.M.S. (4 REQ'D.) #6 EXT. WASHER (4 REQ’D.) #6-32 HEX NUT (4 REQ’D.) #8 x 5/8 SLT. HEX HD. SCR. (4 REQ’D.) LINE CORD ASSY. GROUND STRAP HIGH VOLTAGE SHIELD — FORMED

Page 45

4-18 NO. 510 — GALAGA COCKTAIL — INTERIOR ACCESS

Page 46

NO. 510 — GALAGA COCKTAIL — INTERIOR ACCESS PARTS LIST

PART NO.

0017-00003-0339

A515-00017-01XF A515-00017-02XF 0017-00101-0109 0927-00101-00XF 0017-00101-0598 0610-00132-00ZN 0017-00009-0033 0017-00101-0027 0017-00009-0514 0017-00101-0639 0017-00101-0628 0017-00103-0061 0927-00903-0000 0510-00100-O0XF 0510-00101-O0XF 0510-00901-0100 0510-00901-0200 0017-00101-0620 0017-00103-0061 0017-00101-0341 A508-00011-0000 0017-00042-0256 0017-00032-0093 0017-00103-0054 0017-00032-0051 0930-00104-0000 0017-00101-0025 0930-00904-0000 0017-00031-0044 0017-00003-0219 0017-00101-0555 AS08-00019-0000 0510-00009-0000 A084-90414-C935 0624-00902-0100 0624-00902-0500 0017-00101-0017 0017-00104-0031 0017-00003-0259

A510-00007-0000 A510-00007-0100 A510-00011-0000 A510-00012-0000 A510-00013-0000 A510-00014-0000 A508-00026-0000 A508-00034-0000 A508-00035-0000 A084-91408-B508 A082-91109-A000 A082-91410-A000 ORDER BY PART NUMBER ONLY

DESCRIPTION

ELECTROHOME — 19” COLOR DUAL SYNC. HORIZ. MTG. MONITOR MONITOR SUPPORT ASSY. — RIGHT MONITOR SUPPORT ASSY. — LEFT #8 x 5/16 UNSLOT. HEX HD. BOLT (6 REQ'D.) SUPPORT ANGLE (2 REQ’D.) #8-32 x 5/16 SLT. HEX HD. M.S. (8 REQ’D.) STRIKE (2 REQ'D.) BASSICK CLAMP (2 REQ’D.) — NOT SEEN #8 x 3/4 SLT. HEX HD. SCREW (8 REQ'D.) 2-1/2" HINGE (2 REQ'D.) #8-32 x 1-1/4 CARRIAGE BOLT (4 REQ’D.) #8-32 x 3/4 CARRIAGE BOLT (4 REQ’D.) #8-32 HEX NUT W/SEMS (8 REC'D.) T.V. BEZEL CONTROL PLATE (2 REQ’D.) BOTTOM PAN (2 REQ’D.) DECORATIVE CONTROL SHELF OVERLAY — PLAYER #1 DECORATIVE CONTROL SHELF OVERLAY — PLAYER #2 #8-32 x 1/2 CARRIAGE BOLT (8 REQ’D.) #8-32 HEX NUT W/SEMS (8 REC'D.) #6 x 1/4 PHIL. TRS. HD. SCR. (14 REQ'D.) CONTROL ASSY. (2 REQ’D.) RED PUSH BUTTON ASSY. (2 REQ'D.) PUSH BUTTON SWITCH W/HOLDER (2 REQ’D.) 5/8-11 PAL NUT (2 REQ’D.) SMALL RED BUTTON SWITCH W/HARDWARE (2 REQ’D.) PANEL LOCATING BRKT. (4 REQ’D.) #8 x 1/2 SLT. HEX HD. M.S. (20 REQ’D.) LIGHT SHIELD (2 REQ'’D.) WEDGE BASE LAMP SOCKET (4 REQ’D.) #194 LAMP 14V., .27A. (4 REQ'D.) #6-32 x 5/16 SLT. HEX HD. M.S. (4 REQ’D.) CARD RACK ASSY. W/BOARDS. TRANSFORMER BOARD ASSY. POWER SUPPLY ASSY. P.C. SUPPORT BRKT. 12” LG. (2 REQ'D.) P.C. SUPPORT BRKT. — 6-1/2” LG. (2 REQ'D.) #6 x 1/2 SLT. HEX HD. SCR. (10 REQ’D.) 5/8 DIA. FLAT WASHER (10 REQ’D.) 6" x 9" SPEAKER 8 OHM, 7W.

ADDITIONAL PARTS LIST CONTROL SHELF CABLE ASSY. — PLAYER #1 CONTROL SHELF CABLE ASSY. — PLAYER #2 HIGH VOLTAGE CABLE ASSY. LOW VOLTAGE CABLE ASSY. MASTER CABLE ASSY. VIDEO SIGNAL CABLE ASSY. COIN DOOR CABLE ASSY. AUDIO ADAPTOR CABLE ASSY. MONITOR SIGNAL ADAPTOR CABLE ASSY. FILTER BOARD ASSY. CREDIT MULT. BYPASS P.C. BRD. RAPID FIRE P.C. BRD. ASSY.

4-19

Page 47

V Technical Troubleshooting

Page 48

Harness Component Troubleshooting

Introduction

The most common problems occur in harness components such as the coin acceptor, player controls, interconnecting wiring, etc. The TV monitor and PCB computer cause their share of problems too, but not as much as the harness and its component parts. TV monitor troubleshooting will not be covered here because it is covered in that section of this manual. As you already know, the PCB computer is a complex device with a number of different circuits. Some circuits remain basically the same among games, but overall there are a great many differences between them. PCB troubleshooting procedures, therefore, can be lengthy and will differ greatly among games. However, some basic Z-80 CPU information is involved in this section.

General Suggestions

The first step in any troubleshooting procedure is correctly identifying the malfunction’s symptoms. This includes not only the circuits or features malfunctioning, but also those still operational. A carefully trained eye will pick up other clues as well. For instance, a game in which the computer functions fail completely just after money was collected may have a quarter shorting the PCB traces. Often, an experienced troubleshooter will be able to spot the cause of the problem even before opening the cabinet. After all the clues are carefully considered, the possible malfunctioning areas can be narrowed down to one or two good suspects. Those areas can be examined by a process of elimination until the cause of the malfunction is discovered.

Typical problems falling in this category are coin and credit problems, power problems and failure of individual features. NO GAME CREDIT For example, your prospective player inserts his quarter and is not awarded a game. The first item to check is if the quarter is returned. If the quarter is returned, the malfunction most certainly lies in the coin acceptor itself. First, use a set of test coins (both old and new) to ascertain that the player's coin is not undersize or underweight. If your test coins are also returned, coin acceptor servicing is indicated. Generally, the cause of this particular problem is a maladjusted magnet gate. Normally, this will mean slightly closing the magnet gate a little by turning the adjusting screw out a bit (see section on coin acceptor for more details). If the quarter is not returned and there is no game credit, the cause of the malfunction may be in one of several areas. First try operating the coin return button; if the coin is returned, the problem is most likely in the magnet gate. Enlarge the gap according to the coin acceptor service procedures. If this does not cure the problem, remove the coin acceptor, clean it and perform the major adjustment procedure. If the trapped coin is not returned when the wiper lever is actuated, you may have an acceptor jammed by a slug, gummed up with beer, a jammed coin chute, or mechanical failure of the acceptor mechanism. In this case, first check for the slug that will generally be trapped against the magnet. If so, simply remove the slug and test the acceptor. If the chute is blocked, remove the acceptor and remove the jammed coins. If there is actual failure of the

acceptor, remove the unit and repair as indicated in

the coin acceptor service procedures. If the coin is making its way through the acceptor (that is, falling into the coin box), yet there is still no game credit, you either have a mechanical failure of the coin switch or electrical failure of the coin and credit circuits. The first place to begin is by checking the coin switch. Most of these switches are the make/break variety of micro switch, which is checked by testing for continuity between the NO, NC, and C terminals. When not actuated, the NC and C terminals should be continuous and the NO terminal open. When operated, the NO and C terminals should close and the NC should be open. If the coin switch checks out, examine the connections to the terminals to make sure there is good contact. If necessary, use the continuity tester and check from the terminal lug on the switch to the associated PCB trace. This will tell you if there is a continuous line all the way to the credit circuit.

Page 49

If the coin switch wires do not check out, the problem is in the computer — most likely in the coin and credit circuitry. If you do get game credit when a coin is deposited, but the game will not start when the start switch is pressed, you may have a problem in the start switch, the interconnecting wiring or in the computer. First check the switch. If the switch is OK, proceed to check the wiring. Again, make sure you go from the terminal lug on the switch to the PCB trace. This way, you will check the terminal contact as well as PCB edge connector contact. If the wiring is continuous, proceed to check the PCB credit circuit. If not, check each section of the wiring, until the discontinuity is located. If the wiring is OK, the problem must lie in the computer.

Transformer and Line Voltage Problems

Your machine must have the correct line voltage to operate properly. If the line voltage drops too low, a circuit in the computer will disable game credit. The point at which the computer will fail to work will vary some from game to game, but no game will work on line voltage that drops below 105 VAC. Low line voltage may have many causes. Line voltage normally fluctuates a certain amount during the day as the total usage varies. Peak usage times occur mainly at dawn or dusk, so if your machine’s malfunction seems to be related to the time of day, this may be a factor. A large load connected to the same line as the game (such as a large air conditioner or other device with an exceptionally large motor) may drop the line voltage significantly when starting up. This drop can result in an intermittent credit problem. In addition, poor connections in the location wiring, plug, or line cord may also cause a significant drop in power. Cold solder joints in the game's harness, especially in areas like the transformer connections, interlock switch, or fuse block, may also produce the same results, although probably on a more permanent basis. Sometimes location owners (especially in bars) replace light switches with dimmer rheostats, and the game is sometimes on the same line. Obviously, the voltage available to the game is going to drop dramatically when the dimmer is turned. In any case, the way to check for correct line voltage is with your VOM. Set the VOM to 250 VAC and stick the probes in the wall receptacle. If it's OK here, check the transformer primary connections. If you do not get 117 VAC, examine the solder joints on the transformer, fuse block, and interlock switch. If you do get 117 VAC, the problem must be either in the transformer, harness connections, or in the PCB power supply.

5-2 li you suspect the transformer, check its secondaries with the VOM set to 50 VAC and correlate the readings with the legend on the side of the transformer. The transformer must also be correctiy grounded, so check the ground potential as well, especially if there is a hum bar rolling up ordown the TV screen.

HARNESS PROBLEMS Other harness problems include blowing fuses and malfunctioning controls. The repeating blown-fuse problem can sometimes be quite exasperating to solve, for short circuits have the tendency to occur in areas almost impossible to find. First, try inserting a new fuse, as old fuses age and blow without cause. If the new one also blows, you definitely have a short. The best way to approach this problem is by turning the power off and disconnecting devices that may be causing the problem, such as the TV, transformer, and PCB. Disconnect the devices by pulling off their connectors, but do not allow them to touch. If necessary, insulate them with small pieces of electrical tape. Then, connect your VOM across the terminals of the fuse block (all electrical power shut off), and set it to one of the resistance scales. This will save blowing a fuse each time you want to check the circuit. If the VOM reveals that disconnecting the devices removed the short, reconnect the devices one by one until the short returns. The last device connected is the one that is at fault. If the VOM reads a short even after the devices are disconnected, the fault must lie in the harness itself, and only patient exploration will reveal its location. First, carefully examine all the wiring, looking for terminals that may be touching, metal objects such as coins shorting connections or burned insulation. If necessary, use the VOM to check each suspected wire. MALFUNCTIONING CONTROLS One of the most common problems here is a bad potentiometer. Typically, a bad pot will cause the image to jump as it reaches a certain point. The only cure for this one is to install a new pot. If a feature that is operated by a switch (for example, joysticks, foot pedals, control panel buttons) does not operate at all, check the switch with a VOM or continuity tester to verify its operation. If the switch does not check out, replace it. If the switch is OK, you should suspect the input to the switch from the PCB. In this case, get out the harness and logic schematics and check to see what kind of input it is. In many cases, the input will be +5 VDC. If so, use the VOM to check its presence. Normally, the switch is used to pull a +5 VDC line LOW to GND or to pulla LOW line HIGH. If the PCB output is missing, check the wire length from the PCB. If you find the signal at the PCB trace, the wire length or connection is at fault. If not, begin exploring the PCB using the logic schematics.

Page 50

A Glossary of Microprocessor Terms

MICROPROCESSOR — one or several microcircuits that perform the function of a computer's CPU. Sections of the circuit have arithmetic and comparative functions that perform computations and executive instructions. CPU — central-processing unit. A computing system’s “brain”, whose arithmetic, control and logic elements direct functions and perform computations. The microprocessor section of a microcomputer is on one chip or several chips. PROM — programmable read-only memory. User permanently sets binary on-off bits in each cell by selectively fusing or not fusing electrical links. Nonerasable. Used for low-volume applications.

EPROM — erasable, programmable, read-only memory. Can be erased by ultraviolet light bath, then reprogrammed. Frequently used during design and development to get programs debugged, then replaced by ROM for mass production. ROM — read-only memory. The program, or binary on-off bit pattern, is set into ROM during manufacture, usually as part of the last metal layer put onto the chip. Nonerasable. Typical ROM's contain up to 16,000 bits of data to serve as the microprocessor’s basic instructions. RAM — random-access memory. Stores binary bits as electrical charges in transistor memory cells. Can be read or modified through the CPU. Stores input instructions and results. Erased when power is turned off. LSI — large scale integration. Formation of hundreds or thousands of so-called gate circuits on semiconductor chips. Very large scale integration (VLS) involves microcircuits with the greatest component density. MOS — metal-oxide semiconductor. A layered construction technique for integrated circuits that achieves high component densities. Variations in MOS chip structures create circuits with speed and low-power requirements, or other advantages (static will damage a MOS chip).

Introduction to the

Z-80 CPU

The term “microcomputer” has been used to describe virtually every type of small computing device designed within the last few years. This term has been applied to everything from simple “microprogrammed” controllers constructed out of TTL MSI up to low end minicomputers with a portion of the CPU constructed out of TTL LSI “bit slices.” However, the major impact of the LSI technology within the last few years has been with MOS LSI. With this technology, it is possible to fabricate complete and very powerful computer systems with only a few MOS LSI components. The Zilog Z-80 family of components can be configured with any type of standard semiconductor memory to generate computer systems with an extremely wide range of capabilities. For example, as few as two LSI circuits and three standard TTL MSI packages can be combined to form a simple controller. With additional memory and I/O devices a computer can be constructed with capabilities that only a minicomputer could previously deliver. New products using the MOS LSI microcomputer are being developed at an extraordinary rate. The Zilog Z-80 component set has been designed to fit into this market through the following factors:

  • The Z-80 is fully software compatible with the popular 8080A CPU. Existing designs can be easily converted to include the Z-80. The Z-80 component set is at present superior in both software and hardware capabilities to any other microcomputer system on the market today. For increased throughput the Z80A operating ata 4 MHZ clock rate offers the user significant speed advantages. Microcomputer systems are extremely simple to construct using Z-80 components. Any such system consists of three parts:
  • CPU (Central Processing Unit)
  • Memory
  • Interface Circuits to peripheral devices The CPU is the heart of the system. Its function is to obtain instructions from the memory and perform the desired operations. The memory is used to contain instructions and in most cases data that is to be processed. For example, a typical instruction sequence may be to read data from a specific peripheral device, store it in a location in memory, check the parity and write it out to another peripheral device. Note that the Zilog component set includes the CPU and various general purpose I/O device controllers, while a wide range of memory devices may be used from any source. Thus, all required components can be connected together in a very simple manner with virtually no other external logic. 2.

3.

Page 51

General Purpose Registers There are two matched sets of general purpose registers, each set containing six 8-bit registers that may be used individually as 8-bit registers or as 16bit register pairs by the programmer. One set is called BC, DE and HL while the complementary set is called BC’, DE’ and HL’. At any one time the programmer can select either set of registers to work with through a single exchange command for the entire set. In systems where fast interrupt response is required, one set of general purpose registers and an accumulator/flag register may be reserved for handling this very fast routine. Only a simple exchange command need be executed to go between the routines. This greatly reduces interrupt service time by eliminating the requirement for saving and retrieving register contents in the external stack during interrupt or subroutine processing. These general purpose registers are used for a wide range of applications by the programmer. They also simplify programming, especially in ROM based systems where little external read/write memory is available. Arithmetic & Logic Unit (ALU) The 8-bit arithmetic and logical instructions of the CPU are executed in the ALU. Internally the ALU communicates with the registers and the external data bus on the internal data bus. The type of functions performed by the ALU include: Add Left or right shifts or rotates (arithmetic and logical)

Subtract Increment

Logical AND Decrement Logical OR Set bit Logical Exlusive OR Reset bit Compare Test bit Instruction Register and CPU Control As each instruction is fetched from memory, it is placed in the instruction register and decoded. The control sections performs this function and then generates and supplies all of the control signals necessary to read or write data from or to the registers, control the ALU and provide all required external control signals.

2-80 CPU Pin Description The Z-80 CPU is packaged in an industry standard 40 pin Dual In-Line Package. The I/O pins are shown in the below figure and the function of each is described.

My —_——

MREQ | SYSTEM ong =] CONTROLS 55 21 wm 2

Arsh = 22@_| ADDRESS

—18BUS

HALT <-——] 2-80 CPU

cpu CONTROL | ——r nmi | 7 ew

__26aw

RESET ———* cPU BUSRO = BUS usa «2 contro \"***

Cats 15 D,

¢o—sarees >,

un

sytea

A eked DATA

GND)———»~—> D,BUS

ba? ie Ds Ds Z-80 PIN CONFIGURATION Re= my

5-4

Page 52

Ao-As (Address Bus) Tri-state output, active high. Aj-A;s constitute a 16bit address bus. The address bus provides the address for memory (up to 64K bytes) data exchanges and for I/O device data exchanges. |/O addressing uses the 8 lower address bits to allow the user to directly select up to 256 input or 256 output ports. Ag is the least significant address bit. During refresh time, the lower 7 bits contain a valid refresh address.

Dy-D; (Data Bus) Tri-state input/output, active high. Dy-D; constitute an 8-bit bidirectional data bus. The data bus is used for data exchanges with memory and I/O devices.

M, (Machine Cycle one) ___ Output, active low. M, indicates that the current machine cycle is the OP code fetch cycle of an instruction execution. Note that during execution of 2-byte op-codes, M1 is generated as each op code byte is fetched. These two byte op-codes always begin with CBH, DDH, EDH or FDH. M1 also occurs with IORQ to indicate an interrupt acknowledge cycle.

MREQ (Memory Request) Tri-state output, active low. The memory request signal indicates that the address bus holds a valid address for a memory read or memory write operation. 10RQ (Input/Output Request) Tri-state output, active low. The IORQ signal indicates that the lower half of the address bus holds a valid 1/O address for a I/O read or write operation. An 1ORQ signal is also generated with an M1 signal when an interrupt is being acknowledged to indicate that an interrupt response vector can be placed on the data bus. Interrupt Acknowledge operations occur during M; time while I/O operations never occur during M, time. RD (Memory Read) _ Tri-state output, active low. RD indicates that the CPU wants to read data from memory or an I/O device. The addressed I/O device or memory should use this signal to gate data onto the CPU data bus. WR (Memory Write) __ Tri-state output, active low. WR indicates that the CPU data bus holds valid data to be stored in the addressed memory or |/O device.

5-5 RFSH (Refresh) Output, active low. RFSH indicates that the lower 7 bits of the address bus contain a refresh address for dynamic memories and the current MREQ signal should be used to do a refresh read to all dynamic memories.

HALT (Halt state) Output, active low. HALT indicates that the CPU has executed a HALT software instruction and is awaiting either a non maskable or a maskable interrupt (with the mask enabled) before operation can resume. While halted, the CPU executes NOP's to maintain memory refresh activity. WAIT (Wait) Input, active low. WAIT indicates to the Z-80 CPU that the addressed memory or I/O devices are not ready for a data transfer. The CPU continues to enter wait states for as long as this signal is active. This signal allows memory or I/O devices of any speed to be synchronized to the CPU. INT (Interrupt Request) Input, active low. The Interrupt Request signal is generated by I/O devices. A request will be honored at the end of the current instruction if the internal software controlled interrupt enable flip-flop (IFF) is enabled and if the BUSRQ signal is not active. When the CPU_accepts the interrupt, an acknowledge signal (IORQ during M, time) is sent out at the beginning of the nextinstruction cycle. The CPU can respond to an interrupt in three different modes that are described in detail in section 5.4 (CPU Control Instructions). NMI (Non-Maskable Interrupt) Input, negative edge triggered. The non maskable

interrupt request line has a higher priority than INT

and is always recognized at the end of the current instruction, independent of the status of the interrupt enable flip-flop. NMI automatically forces the Z-80 CPU to restart to location 0066. The program counter is automatically saved in the external stack so that the user can return to the program that was interrupted. Note that continuous WAIT cycles can prevent_the current instruction from ending, and that a BUSRQ will override a NMI. RESET Input, active low. RESET forces the program counter to zero and initializes the CPU. The CPU initialization includes:

  • Disable the interrupt enable flip-flop
Page 53
  • Set Register | = 00H
  • Set Register R =00H
  • Set Interrupt Mode 0 During reset time, the address bus and data bus go to a high impedance state and all control ouput signals go to the inactive state.

BUSRQ (Bus Request) Input, active low. The bus request signal is used to request the CPU address bus, data bus and tri-state output control signals to go to a high impedance state so that other devices can control these buses. When BUSRQ is activated, the CPU will set these buses to a high impedance state as soon as the current CPU machine cycle is terminated. BUSAK (Bus Acknowledge) Output, active low. Bus acknowledge is used to indicate to the requesting device that the CPU address bus, data bus and tri-state control bus signals have been set to their high impedance state and the external device can now control these signals. Single phase TTL level clock which requires only a 330 ohm pull-up resistor to +5 volts to meet all clock requirements.

Basic Logic and Processor Books

  • UNDERSTANDING SOLID STATE ELECTRONICS By: Texas Instruments $2.95 Radio Shack $1.95
  • TTL COOKBOOK By: Dom Lancaster $8.95
  • DIGITAL VIDEO TEXT BOOK By: Kush-N. Stuff Wico $14.95
  • BEGINNER'S GUIDE TO MICROPROCESSORS By: Charles M. Gilmore Tab Books $5.95
  • AN INTRODUCTION TO MICROCOMPUTERS By: Adam Osborne $7.50
  • 8080 SYSTEM USER’S MANUAL By: Intel $5.00

Prices may vary

Page 54

PLEASE NOTE:

THE INFORMATION CONTAINED IN THIS SECTION IS TOLD IN AN EASY TO UNDERSTAND MANNER AND IS INTENDED TO AID THOSE WITHOUT AN ELECTRONICS DEGREE IN TROUBLESHOOTING AND REPAIRING THEIR GAMES T.V. MONITOR.

IF YOU READ THROUGH THIS SECTION AND STILL HAVE QUESTIONS, PLEASE CONTACT YOUR DISTRIBUTOR OR MIDWAY MANUFACTURING COMPANY AT THE TOLL FREE NUMBER PROVIDED WITH YOUR GAMES PAPERS.

OUR STAFF AND OUR DISTRIBUTORS STAND READY TO HELP YOU!

THANK YOU

VI T.V. Monitor

Page 55

Color T.V.

Color T.V Monitor

Introduction: (How to use this section of your manual.)

This section has been designed to simply familiarize you with one of the more mystical components in your game — the T.V. monitor. If you are an electronics technician who is quite knowledgeable on the subject, you may decide to just go to the schematics and start troubleshooting the defective monitor. But if you are like most people, a monitor is a T.V. set, and that means a complex doo-dad that means big buck repairs. This isn’t necessarily so. This section of the manual will acquaint you with the monitor and could just help you repair it if you feel adventurous enough to give it a try. If you have any knowledge of electronics, especially the use of a voltmeter, the repairs you can make are astonishing. Just keep in mind that ELECTRICITY CAN BEVERY DANGEROUS, SO BE CAREFUL!!

If you want to understand how a monitor works, just read the “THEORY OF OPERATION” subsection. If you wish, you can follow along with the schematics. The information is presented in a very basic manner but more complete treatment of the subject can be found in the technical sections of bookstores.

If you want to attempt to repair your monitor, it would be a good idea to read this whole section beginning to end before starting. Pay attention to all warnings

6-1 and take them seriously. The more equipment you have the better, but a low cost Volt-Ohm-Milliameter can often do the trick. Here are the steps to take:

  • Find the symptom that matches the problems your monitor has in the “SYSTEM — DIAG- NOSIS” subsection. The diagnosis tells the circuit or area the problem may be in and possibly even the actual componeni causing it.
  • Once you have the circuit that is causing the trouble, read the “TROUBLESHOOTING” subsection to learn the procedure for finding the bad part. Next, go to the schematic section and find the schematic that matches your monitor. It may be helpful to read the “DIFFERENCES BETWEEN MONITORS” subsection if you are unsure of which monitor you have. Use the schematic to see what parts are in the offending circuit.

That really is all there is to it. Just remember that there are some bizarre or rare symptoms not covered, or that a monitor may have two or more different problems that only a genius, the experienced, or an experienced genius can figure out. But be patient, follow safety precautions, and remember that there is also literature available from the monitor companies through your distributor or from Midway Manufacturing Company on request. (There is a toll free number on the back side of the front cover of this manual.)

Page 56

Symptom Diagnosis

. Insufficient width or heighth: A. Horizontal line (due to VERTICAL CIR- CUIT DEFECT). e Bad yoke. e Bad vertical output section. « Open fusible resistor in vertical section. e Bad height control. e Bad flyback. Vertical line (due to HORIZONTAL CIR- CUIT DEFECT). © Bad yoke. ® Open width coil. e@ Open part in horizontal output section. Picture spread out too far or crushed in certain areas: A. Horizontal or vertical output transistor. B. Bad component in output circuitry. Line too close with black spacing: A. Problem in vertical section causing poor linearity. Poor focus and convergence: A. Bad high voltage transformer (“flyback”) or control. B. Focus voltage wire not connected to neckboard terminal. Colors missing; check: A. _ Interface color transistors. B. Color output transistors. C. Cracked printed circuit board. D. Color circuits. E. Video input jack. Picture not bright enough: A. Weak emission from picture tube. (Turn horizontal sync off frequency and put brightness all the way up for about 15 minutes. Occasionally this cures the problem.) Silvery eftect in white areas; check: A. Beam current transistors. B. Weak picture tube emission. Too much brightness with retrace lines; check: A. Beam limiter transistors. B. Brightness and/or color blanking control set too high. Increasing brightness causes an increase in size and poor focus. A. Weak high voltage rectifier or regulation (high voltage unit).

6-2 10.

11.

12.

13.

14,

15.

16.

17.

18.

19. Small picture and/or poor focus: A. Low B+ voltage (power supply trouble).

Vertical rolling: A. Vertical oscillator transistor, IC, or circuit. B. No sync from logic board.

Horizontal line across center: A. Vertical output circuit is dead (see symptom No. 1. A). B. Vertical oscillator is not putting out the right wave form. Picture bends: A. Horizontal sync needs adjusting. B. Magnetic or electromagnetic interference.

Flashing picture, visable retrace lines: A. Broken neck board. B. Internal short circuit in the picture tube (arcing). Unsymmetrical picture or sides of picture: A. Defective yoke.

No brightness, power supply operating — No high voltage for the picture tube; check: A. Horizontal oscillator. B. Horizontal amplifier and output. C. Flyback transformer (high voliage unit).

No brightness, high voltage present; check: A. Heater voltage to the tube at the neck board. B. Screen-grid voltage for the tube. C. Focus voltage. D. Grid to cathode piciure tube bias.

No o high voltage; check:

For AC input to the “flyback”. Horizontal deflection stages. Flyback transformer. Yoke. Power supply. moOm>

No horizontal and vertical hold; check: A. Sync transistors and circuit. B. Wires and jack irom logic board to the monitor. Wavey picture — (power supply defect); check: A. Transistors, diodes, electrolytic capacitors in the power supply.

Page 57

23. . Moving bars in picture: A. Ground connector off between monitor and logic boards. B. Defect in the power supply (see wavy picture symptom).

Washed out picture (see picture not bright enough): A. Check video signal at the cathode pins with an oscilloscope. If there is about 80 volts peak to peak, the picture tube has weak emission.

Monitor won't turn on: A. Problem in the power supply: Check fuse, transistors, open fusible resistor. B. Shorted horizontal output transistor. C. Defective high voltage disabling circuit. D. Crack(s) somewhere on main chassis board.

24, Can't adjust purity or convergence: A. Use a degausser to demagnetize the picture tube carefully following your degausser’s instructions. Picture tube defective.

shield.

interferring. m 9 99

purity. F. Poor focus or width of picture.

Guide To Schematic Symbols

THERMISTOR (POLARITY DOESN’T MATTER)

SVT VW INDUCTOR, COIL, CHOKE (POLARITY DOESN'T MATTER)

(-) CATHODE

(+) ANODE

ZENER DIODE IRON CORE TRANSFORMER (SUCH AS A FLYBACK)

OL

FUSE (POLARITY DOESN'T MATTER)

CATHODE (-)

ANODE (+)

DIODE Metal foreign material is in picture tube

Nearby equipment is electromagnetically

The poles of the earth are pulling off the

Page 58

COLLECTOR Pat COLLECTOR a BASE ———>- BASE————> EMITTER TE EMITTER —

NPN TRANSISTOR PNP TRANSISTOR

Ww

VARIABLE RESISTOR, POT, CONTROL RESISTOR (POLARITY DOESN’T MATTER) (POLARITY DOESN’T MATTER)

+ +

LINES ARE CONNECTED ELECTROLYTIC CAPACITOR

LINES ARE NOT CONNECTED CAPACITOR (POLARITY DOESN'T MATTER)

hy g = GROUND

6-4

Page 59

Troubleshooting

Troubleshooting monitors requires experience, patience, and luck. The first step is to match the symptom the monitor displays to the diagnosis next to it in the “SYMPTOM-DIAGNOSIS” subsection. This will pinpoint the circuit the problem is probably in, and often the parts to check. Next, the circuit should be visually inspected to see if there are any parts broken, burned, or if something is there that shouldn't be, like a loose screw, etc. Some parts go bad before others and should be checked first. In fact, following is the general order in which parts usually go bad:

  • Semiconductors (like transistors, diodes, and integrated circuits). Fusible resistors. Electrolytic capacitors. Resistors. Capacitors and coils. Always remember that a monitor can bite like a snake. Even when it is turned off, capacitors hold voltage and will discharge it to you should you be touching chassis ground. The picture tube or CRT, itself, is a giant capacitor, so avoid the flyback anode plug hole. With the monitor on, the power supply circuit and/or the flyback, which puts out at least 18,000 volts, CAN BE KILLERS!! Avoid handling power transistors (usually output transistors), yoke terminals, and other high power components when the monitor is on.
WARNING: That picture tube is a bomb! When it breaks, first it implodes, then it explodes. Large pieces of glass have been known to fly in excess of 20 feet in all directions. DO NOT carry it by the long, thin neck. Discharge its voltage to ground by shorting the anode hole to ground. Use a plastic handled screwdriver, connect one end of a wire with an alligator clip at each end to chassis ground and the other end to the metal shaft of the screwdriver. Using ONE HAND ONLY (put the other in your pocket) and touching ONLY the plastic handle of the screwdriver (DO NOT TOUCH THE METAL SHAFT) stick the blade of thescrewdriver into the anode hole. Be prepared for a fairly loud pop and a flash. The longer the monitor has been turned off, the smaller the pop and dimmer the flash. But BE CARE- FUL, picture tubes will hold a very ARON

6-5 healthy charge for at least a week if not longer. Even after you've discharged it once, it may still carry a residual charge. It’s better to be too careful than dead, which is why electronic equipment always carries stickers referring servicing to qualified personnel. Handle the side with the viewing screen against your chest when changing it. ALWAYS wear safety goggles when handling the picture tube.

To maintain the safety and performance of the monitor, always use exact replacement parts. For instance, the wrong components in the power supply can cause a fire, or the wrong color transistor may give a funny color to the picture. Service your monitor on a nonconductive firm table like wood, NOT METAL, and take off all of your jewelry just in case. With all this in mind, you are ready to begin troubleshooting.

Observe the picture carefully. Try to vary the appropriate control that would most likely affect your particular symptom. For example, if there is poor brightness or no picture, try turning up the brightness or contrast control. If the controls have no effect at all, chances are there is trouble with the control itself, the circuit it controls, or a nearby circuit that may be upsetting voltages. Go to the list of symptoms and determine with the schematic where the bad circuit is.

CAUTION:

Keep in mind that capacitors hold a charge as can the picture tube (for at least a week and usually longer), and could shock you.

First, check for obvious visual defects such as broken or frayed wires, solder where it is not supposed to be, missing components, burned components, or cracked printed circuit boards. \f everything looks good up to this point, make sure that diodes, electrolytic capacitors, and transistors have their leads connected in the right polarity as shown on the schematic and the circuit board. Turn on the power and measure the voltages at the leads of the active devices such as tubes, transistors, or integrated circuits. Any voltage that does not come within at least 10% to 15% of the voltage specified on the schematic indicates either a problem with that device or a component connected with it in the circuit. The next step is to use the onmmeter to narrow down the field of possible offenders.

Page 60

To test a transistor, one lead of the ohmmeter is placed on the base; and the other lead placed just on the emitter, then on the collector. A normal transistor will read either high resistance (infinite), or little resistance (400 to 900 ohms), depending on the polarity of this type transistor. Then the leads should be switched, one remaining on the base, and the other switched from the emitter to the collector. Now the opposite condition should result: the resistance should be infinite if it was lower when the other lead was on the base. Consistantly infinite readings indicate an open, anda short is demonstrated by 0-30 ohms on most of these test readings. Finally, place one lead on the collector, then the other on the emitter. No matter which lead is used, there should be infinite resistance. Any lower reading, such as 50 ohms (which is typical on a bad transistor), indicates a short. This all sounds pretty confusing, but a little experience on a good transistor will make you an expert in no time. Usually, the lowest ohmmeter setting is used for testing transistors. Once in a great while a transistor may check out good on this test, but may actually be “leaky” or break down only on higher voltages. If in doubt, change it. It is also wise to check the transistor out of the circuit just in case some component in the circuit is affecting the onmmeter reading. A diode is tested like a transistor except it only has two leads. Again, there should be high resistance one way and little resistance the other. If it tests bad, take one lead out of the circuit in case somecomponent is messing up the ohmmeter reading.

NOTE: DO NOT leave soldering equipment on the leads too long since all semiconductors, especially integrated circuits, are easily destroyed by heat.

Without special equipment, integrated circuits are checked by verifying the proper DC voltage on the pins and the correct AC wave form using an oscilliscope. BE CAREFUL: Shorting their pins can easily destroy them. Resistors are checked with an ohmeter and should usually be within ten percent of the value stated on them and on the schematic. You may have to desolder one lead from the printed circuit board. If you wreck the foil on the board, carefully solder a small wire over the break to reconnect the conductive foil. Capacitors are tricky. Their resistance goes up when checked with an ohmmeter which shows acharging action. As they suck up current from the meter, the voltage goes up and so does the resistance. If you are sure a particular circuit is giving you a problem and everything else checks out O.K., Electrolytic capacitors are prime suspects. Substitute a new one and keep your fingers crossed.

Theory of Operation

To understand what goes on inside the monitor, large general groups of circuits will be examined instead of laboriously analyzing the branches and small circuits that make up these groups. This will help avoid confusion and aid in a basic, concrete, knowledge of what makes up a monitor.

THE POWER SUPPLY — The AC going to the monitor from the game transformer is just like the voltage and current from your wall outlet. It jumps up and down going positive and negative sixty times a second. But a monitor needs nice, smooth DC; direct current, not alternating. So diodes chop up the AC and a big electrolytic capacitor filters it out to make it even smoother. Since the monitor is a big piece of electronic equipment, with many circuits demanding a lot of power from the power supply, there are also zener diodes and transistors to help maintain a nice, constant, smooih voltage so that the monitor circuits don’t jump around. And this is what happens when you see a wavy picture. There is AC creeping

6-6 through the power supply, so it must be malfunctioning. If the voltage from the power supply is too low, the other circuits will be starved for power and you may see a small, wavy picture, or noneatall. Some circuits receive voltages that are higher than what the power supply should put out. Butthey come from the flyback transformer which will be discussed later. THE INTERFACE SECTION OF THE CHASSIS — The interface section of the chassis is fairly easy to identify. It is right by the place where the video jack(s) from the logic board(s) plug into. There are sets of transistors that receive the separate red, green, blue, and sync information from the cables that come from the logic boards. The circuits jack up the voltage and match impedances, or in other words, prepare the logic board outputs for the circuits that will really amplify them for the output devices such as the yoke in the case of the sync, or the picture tube that shows the colors.

Page 61

An interesting aside is that our sync is composite negative sync. That means two things:

  • The sync is a negative going wave form.
  • There are two pulses going at different speeds over the same wire: a. Vertical wave forms at 60 times per second (or Hertz) and b. Horizontal wave forms at about 15,750 times per second (Hz).

The sync is amplified by a sync amplifier transistor and sent on its way to the oscillators. The sync or timing information will be explained along with the oscillator shortly. The color information is sent via wires to the neck board where the main amplification occurs. This will also be discussed later.

VERTICAL AND HORIZONTAL DEFLECTION — After the sync signal is amplified by the sync amp, it goes to two different sections, the vertical and horizontal circuits. Basically, the sync signals are for timing so the picture doesn't mess up since it is assmebled like an orderly jigsaw puzzle, but so fast that you can't see the electron beams for each color painting the picture on the screen. This will all become clear soon. For now, we will follow the 60 cycle component of the sync as it goes on its journey to the deflection yoke. The 60 cycle pulse goes to the vertical oscillator to make sure this circuit goes back and forth (or oscillates) at 60 times a second. Without this pulse keeping the circuit at the correct speed, it may get lazy and oscillate at 58 cycles or lower, or get ambitious and oscillate at 62 cycles or higher. At the wrong speed, the picture will start to roll up or down. A Wells Gardner 13” or 19” color monitor uses transistors for its sync section. An Electrohome 13” or 19” color monitor uses an integrated circuit IC501 for its sync section. The idea is all the same. The output to the vertical amplifying transistors for all monitors must be a sawtooth wave form, sortoflike a bunch of pyramids, racing to the yoke's vertical coils at 60 times a second. Along the way to the output transistors, the 60 cycle pulse is shaped and amplified to do the job: the yoke magnetically pushes the electron beam to fill the screen out sideways looking at the screen with the greatest length going up and down. Or viewing the screen sitting like a home television set. The amplified vertical output fills the screen up and down. Watching a monitor like this, seeing only a horizontal line means a problem with the vertical coils of the yoke or anything from the vertical output section on back to the oscillator.

6-7 The horizontal section is very similar with a few exceptions. The horizontal wave shape is more like a square and has a frequency of 15,750 cycles a second. Again, Wells Gardner uses transistors for the horizontal oscillator, and Electrohome uses the other side of IC501. Still, the effect is the same. If the oscillator isn’t going at the correct speed, the picture may move sideways, start to slant, or tear up with slanted thin figures. With both the vertical and horizontal of all monitors, there are variable resistors that change the speed of the oscillators up and down. This way you have controls that can make the correct frequencies to keep the electronic jigsaw puzzle nicely locked in place. If you're driving in a car and next to you someone else is driving their car at exactly the same speed, it will appear that they are not moving. And this is why the sync frequency and the oscillators frequencies must match, so the picture doesn't appear to move. The correct wave form is shaped and amplified in the circuitry just like in the vertical section. But the horizontal output transistor is a large power transistor and not only serves to give current to the horizontal yoke windings, it also feeds the flyback transformer.

THE FLYBACK TRANSFORMER (OR HIGH VOLTAGE UNIT)

HIGH VOLTAGE UNIT) — The picture tube needs high voltage to light up, and the power supply can’t meet this demand. The flyback transformer receives current alternating at about 15,750 times per second from the horizontal output transistor. The “flyback” jacks up its input voltage and puts out a higher voltage alternating at the same speed. But, in your “flyback” there are diodes that chop up the alternating voltage to make it a smooth DC output just like in the power supply. This is what goes through that thick red wire to your picture tube. THIS AREA HAS ABOUT 18,000 VOLTS ON IT AND IT CAN KILL YOU!! The “flyback” may be dangerous, but it is also generous. It has extra output windings which give voltage to the heater pins of the picture tube, voltage for the vertical deflection circuits, and picture tube screen-grid voltage. So in a way, ihe high voltage “flyback” is like a second power supply.

COLOR CIRCUITS The color circuits are pretty straight forward. The signals go into the interface section where some amplification and impedance matching occurs. These circuits are pretty sparse and simple. Each color just has two transistors and a diode with some resistors and capacitors. From here, the AC color signal is sent by wires to the neck board. The color output circuits are on the neck board. The color signals going to the transistors are controlled by two variable resistors called drive controls. There only two, one for the red and one for the green. The

Page 62

blue doesn’t have one. In the emitter part of each transistor is another variable resistor that is the cut off control. These conirols vary the amount of amplified AC signal that goes to the cathodes of the picture tube. The more signal, the more color. The bases of each of these transistors are connected together and are all connected to the blanking and beam limiting transistors which are in the interface section. The beam limiter helps control the brightness level, and the blanking transistor rapidly turns the picture tube on and off so that retrace lines don’t show up on the screen. By turning up the brightness on a good monitor, these four to six retrace lines can be seen slanting diagonally across the picture.

PROTECTION CIRCUIT — To protect the high voltage section against voltages that are too high coming from the power supply which could cause X-rays to be emitted from the “flyback”, a circuit senses the higher power supply voltage, and using a transistor, turns off the horizontal oscillator. Since the horizontal oscillator doesn’t work, the horizontal output transistor has nothing to feed the “flyback” which in turn has nothing to feed the picture tube. The monitor will be silent, have no picture, and will appear to be off. But don’t be fooled. There is still that excessive amount of voltage coming from the power supply. To find out, check the emitter on TR502 of the Wells Gardner monitors; or the emitter of X04 for the Electrohome monitor. Here are the voltages you should receive: Wells Gardner = 127VDC Electrohome = 120VDC

The best place to measure this voltage on an Electrohome monitor is at a pin marked B1 on the chassis. This is because a 13 inch color Electrohome monitor, the GO7-FBO or G07-902, has an integrated Circuit and very little else in the power supply. Still, there should be 120VDC at B1.

THE PICTURE TUBE (OR CRT) — The picture tube or CRT is an output device. In other words, the end result of the circuits work is displayed by this part. Actually, the output of other circuits is in the neck of the picture tube. First, there is the heater. The heater boils off electrons from the cathodes so that they (the electrons) shoot up to the screen to excite the phosphors so that the three phosphors emit three colors of light. The cathodes are next, and again they emit electrons to turn on the tube phosphors, making it glow. The cathode can arc or short to the heater resulting inno picture and a defective picture tube. Next come the grids. The first grid is grounded. The following grid is the screen grid which receives about 300VDC depending on the brightness setting. The next grid closest to the picture tube screen is the focus grid which gets about one fifth the amount of voltage that is applied to the picture tube anode. After jetting from the cathode through all these grids, the electrons speed through a mask, a sheet of material with tiny holes, and then excite the tiny dots of phosphor in the inside surface of the picture tube screen. The green electron gun (or cathode and circuitry) spits out electrons which head for the green phosphors only. The same goes for the red and blue guns. The way the phosphor light blends determines the color seen. Should these electron beams become too intense, they may burn the phosphor. With the monitor off, this can be seen as a dark permanent image of the video information on the tube screen.

Differences Between Monitors

The easiest way to identify the brand of monitor you are working with, assuming you can't find the brand name written on it anywhere, is to see if there are two circuit boards rising up from the chassis toward the picture tube neck. In other words, they stand up, or are perpendicular to the chassis, with a black plastic bracket holding them in place. This is adescription of a Wells Gardner monitor. They use separate boards for main chunks of circuitry. Therefore, you have a “power board” (the power supply), an “interface board” (the interface section), and a “horizontal/ vertical board” (for the deflection circuitry). Still, there are a few parts on the chassis, but most can be found on the board. An Electrohome monitor has no separate boards, except for the neck board, and just has a flat chassis. Another good way to determine which monitor you have is to check the transistor call out numbers that are printed on the chassis next to the part. For instance, on the neck board, one of the color output transistors is TR401. If you look through the schematics or the parts lists, you will find TR401 in the Wells Gardner literature. On the other hand, the neck board transistor may say X101. X101 can be found in the Electrohome literature. So, all Wells Gardner transistor call outs begin with TR, and Electrohome transistor call outs start with an “X".

Page 63

Parts Interchangeability Some parts can be interchanged on all of the monitors. Here are the rules:

  • You CAN swap the voltage regulator TR502 or X01 on any Wells Gardner or Electrohome 19 inch monitor. You CAN NOT swap the voltage regulator on the 13 inch Wells Gardner or €lectrohome (G07-902) since the Electrohome uses an integrated circuit for the power supply. . You CAN NOT change any part that is a safety part, one that is shaded in gray onthe schematic; it MUST be IDENTICAL to the original. To do otherwise IS DANGEROUS. For instance, the 13 inch Electrohome (G07-904) monitor “flyback”. looks identical to the 19 inch Electrohome (G07-904) monitor “flyback”. In fact, there is even a 19 inch Electrohome (G07-905) monitor (which is an obsolete model) with a similar looking “flyback. NONE OF
  • You CAN swap any resistor between monitors THESE ARE INTERCHANGEABLE!

that has the same resistance, wattage rating, 6. You CAN change any of the parts between the and tolerance. G07-904 and GO07-907. They're essentially the same monitor except that the GO7-907 has a

  • You CAN swap any capacitor between monitors vertically mounted picture tube. ing the same capacitance, and voltage lf there is any doubt about what parts can be swapped between each manufacturer’s 19 inch and 13 inch models, compare the manufacturer’s part
  • You CAN swap any 19 inch picture tube on the number between each one. If they match up, they are monitors. the same part.
Page 64

WELLS-GARDNER 1I9” COLOR MONITOR SCHEMATIC DIAGRAM # Mosi-00087-Aol2

INTERFACE BOARD P317

VERTICAL RASTER

807 CA 7509) SOK VEN

aubo7 FaWeR "7, TOTTO! Ms.UNIT . cRTIgwtp22 2 BOARD ERROR AMP. isea7s iseore {

POSITION ADJUSTMENT CENTER Lroz up DOWN

rece [Ve

  • ' MAIN BOARD |[MQ-29 we Sd 7
vost.vOStVPRE DRIVE Y <yDRIVE__v.OUT V.AMP.FU TOKE COM~
350626z5ci7402scitag|S)”“ascirao2sciragprorre2®
rao,AseSCI786eIEACTR305250490 TRIOT780vemcat2@|
RO cigigasagzs "R80? 5908 ascigsTR3O8 Tecraig AOS PSAA9O TRIO” gsciaisoh
r1TaeH

211 aie aro S70 ino ti, 5% aw 0%,

on .

Ped eserazorTe208
'¥++
esosL]|]2csigBo"Bo
25c1625ee‘sod Lnezesaw. 3494M 8%:
TR353TR3S4 25A825acacia =fs]oo nel
Z5ci740/ 2501815 2SA10I8 7250826,aco(faax |ése0=

a8 © veov 4

' eee HORI, RASTER | 20° [A _Bosition abu. Perce -

‘

Sane iva} LSS

= 603 cose 151088 sae

x02 x601 HOR. DRIVE 2. TR3S2 25CI722/ 354

ar ers “Sacer 8 %. cea

Foe ace: ‘ovisy

T yn

o zsaene 250826 2sc2088 { [service TIP

dsc 28 1625,

ae K4625A, K4626A, K4675A — 5816 f 6-10

Page 65

VERT/HOR BOARD (MT/QJ) NECK BOARD (MS/QG)

Rel. No.Part No.DescriptionRet. No.Part No.DescriptionRef. No.Part No.DescriptionRef. No.Part No.Description
RESISTORSCAPACITORS (CONT.)RESISTORS
R301203X6500-628820 Ohm, * 5%, 1/8W Carbon6313203X0025-08747 uF, 50V Electrolytic5
F302203X6500-90212k Ohm,5%, 1/8W CarbonC315203X0015-08210 uF, 25V Electrolyticetlpeedi gam 4 eee403202X7000-2471000 pF, 50V, 10% Ceramic
R303203X6500:92715k Ohm, = 5%, 1/8W CarbonC316203X1100-2203300 UF, 50V, + 10% Mylara303x6800.708Vek Ohm 3. 5% BW CarbonC404202X7110-0191500 pF, 2kV' + 10% Ceramic
R304203X6500-88610k Ohm, = 5%, 1/8W Carbon317202X8000-616100 pF, 50V, * 10% CeramicRaos503x650 447150 Ohm = 5% 1/8W CarbonC405202X7150-018100 pF, 12kV, + 10% Ceramic
R305,203X6501-241330k Ohm, * 5%, 1/8W Carbon351202X7000-2811500 pF, 50V, = 10% CeramicRaosD0axes00 ast220 Ohm & 8% EW CarbonC408202X7050-48301 UF, 500V, + 10% Ceramic
F306203X6500-6451k Ohm, # 5%, 1/8W CarbonC352202X7000-247aoe203X6500-447450 Ohm # 8% 4/8W CarbonC407202X7110-0191500 pF, 2kV + 10% Ceramic
R307203X6500-6891.5k Ohm, * 5%,1/8W CarbonC353203X 1100-5730.022 uF, 50V, + 10% Mylarfagerexesoo-s0s270 Ohm & 5% BW CarbonC408202X2000-55068 pF, 50V, + 10%Ceramic
R309203X6500-7242.2k Ohm, = 5%,1/8W CarbonC355203X 1100-8580.1 uF, 50V, + 10% Mylarfoe5036600608570 Ohm 2.5% WBW CarbonC409202X8000-55068 pF, 50V, + 10% Ceramic
R310203X6501-285470k Ohm, * 5%,1/8W CarbonC356203X0015-1054.7 uF, 25V Electrolyticpredcoane=co 600WW CoenC410202X8000-55068 pF, 50V, + 10% Ceramic
311203X6501-06556k Ohm, * 5%, 1/8W CarbonC357203X1201.0130.015uF, 200V + 10% PPBaeeoaitis0 600aw Caton
R312203X6501-126100k Ohm, 5%,BW Carboncase203% 1201-0342.018 uF, 200V, = 10% PPaenaxee 800qEVi/Catbon
R313,203X6001-32640k Ohm, +farbon369203X0040-014.7 uF,lectrolyticfae
R314203X6501-04447k Ohm, # 5%, 1/8W CarbonC360202x7000-4820.01 uF, 50V, + 10% CeramicPiedporePelid teleHares tiSEMICONDUCTORS
R315203X6500-628820 Ohm, + 5%,1/8W Carbon361203X 1100-5090.015 uF, 50V, + 10% Mylarepoca
R316203X6500-420120 Ohm, + 5%.1/8W CarbonC362203X0025-05810 uF, 50V Electrolyticuemcatana2e-0hm * 5 ‘ eo Orie”;
R317203X6206-4412.2 Ohm,5%, 1/2W CarbonC363203X1205-4870.01 uF, 630V, + 10% PPeae3osxee0t3 3oth Onn = 10%Ae Comeu200X3206-800Transistor, 28C2068, 2SC1514
F319203X6500-169100 Ohm, * 5%,1/8W CarbonC364202X7000-4820.01 uF, 50V, * 10% Ceramic::om:(R output)
X6500-92715k Ohm, + 5%.1/8W CarbonR417203X5601-3132.7k Ohm + 10%1/2W Gomp.TR402200X3206-800Transistor, 2SC2068, 2SC1514
320203x6500-15k Ohm, +5%,aRAB203X5602.254470k Ohm * 10% 1/2W Comp.(G output),
aeoserne steIm, + SM, 1/2 CarbonEMICONDUR419203X5602-185330k Ohm + 10% 1/2W Comp.‘
R322203X9100-12122 Ohm, + 5%, 2W MO.SICTORSnae303x51081171.0 Ohm = 10% 2W Metal OxideT7403200X3206-800Transistor, 25C2068, 2SC1514
203X6500-6891.5K Ohm,5%, 1/8W Carbon‘m(B output)
me"iR423203X5102-155270k Ohm + 5% t/4W Carbon‘
R324203X6500.98827k Ohm, * 5%,1/8W CarbonR301200X4082-614Transistor, 25A826Qvnagtsoaxctisord500 Ohm Varistor R Drivex404201X2100-126Diode, 182367 (protector)
F325203X6500-32647 Ohm, + 5%,V/8W CarbonTR302200X3174-006Transistor, 28C1740Qveaaepoaxsiieota200 Ohi Verlator 8 DriveX405201X2100-126Diode, 1S2367 (protector)
F328203X6500-628820 Ohm, + 5%,1/8W CarbonR303200X3174-006Transistor, 2581740vnaesPpaSc Oha varisionh CioX406201X2100-126Diode, 182367 (protector)
F330203X6500-88610k Ohm, * 5%,1/8W CarbonTR304200X3174.006Transistor, 28617400Vadotaeti Onn Varlstor e'Gutott
R331203X6501-209220k Ohm, + 5%,1/8W CarbonTR305200x4049-081Transistor, 2SA490YLBGLIvnaosBovrserenedBONG Vedoee BCitOH
R351203X6500-72422k Ohm,5%, 1/8W CarbonTR306200X3162.538Transistor, 2SC1625YLBGLIioneeeaM Olananetar cereen
R352203X6500-92715k Ohm, + 5%,1/8W CarbonTR307200X3174.014Transistor, 2SC1740Rvimsvaristor. sereee:MISCELLANEOUS
R353203X6500-94418k Ohm, + 5%, 1/8W CarbonTR308200X3174-006Transistor, 28C17400
R354203X6500-7833.9k Ohm, + 5%, 1/8W CarbonTR351200X4085-415Transistor, 2SA854QCAPACITORSJ401206X5003-729Socket, 5 Pin
R355,203X6500-90212k Ohm,5%, 1/8W CarbonTR352200X3172-208Transistor, 28C17228KS402206x5003.983Socket. 3 Pin
356203X6500-561470 Ohm, * 5%, 1/8W CarbonTR353200X3174-006Transistor, 2861740C401202X7000-2471000 pF, SOV, 10% CeramicP4o1204X9600.329Plug, 5 Pin
R357203X6500-7242.2k Ohm, * 5%,1/8W CarbonTR354200x4082-614Transistor, 2SA826Q_C402202X7000-2471000 pF, 50V, 10% CeramicPao204x9600-254Plug, 3 Pin
R358203X6500-6661.2k Ohm, + 5%,1/8W Carbonx301201X2010-144Diode, (Sl) 1$2473-172
R359203X6501-08868k Ohm, = 5%,1/8W Carbonx302201X2010-144Diode, (Si) 1$2473-T72
R360203X5500-47127 Ohm, + 5%, 1/4W Comp.X303200X8000-026Diode, (GE), INGOTVGL
R361203X6000-9981.2k Ohm, + 5%, 1/8W Carbonx304200X8010-165,Diode (SI) 1SS81
R363,203X6500-6661.2k Ohm, * 5%,1/8W CarbonX305201X2010-165Diode (SI) ISS81
F364203X9014-98847k Ohm, + 5%,1W MO.X306201X2010-165,Diode (SI) ISS81
R365,203X6700-98956k Ohm! + 5%,1/2W Carbonx307200X8010-102Diode (SI) MA26W4* 297X2000-072 HIGH VOLTAGE ASSEMBLY (1701)FINAL ASSEMBLY PARTS
F366203X6001-1483.3k Ohm, 5%, 1/8W Carbon308200X8010-094Diode (Si) 182473
R367340X2222-7342.2k Ohm, + 5%, 1/2W Carbonx351201X2010-144Diode (SI) 1S2473-172R701204X1625-0583.3 Ohm, + 10% 10W WW Resistor4% 88X-0129-50619VJTP22 Pix Tube
F368203X6500-7853.9k Ohm,118W Carbonx32201X2010-144Diode (SI) 1S2473-T72R702204X3901-125Focus Control38A5554-000Assy. Purity Shid/Degaussing
R369203X6500-7623.3k Ohm,1/4W CarbonX353201X2010-144Diode (Sl) 182473-T72x701Diode (S! KV)205X9800.256Lateral/Purity Assembly
370302X6100-9611k Ohm, + 5%, 1/4W Carbonx354201X2010-144Diode (SI) 182473-T72x702Diode (SI HV) > Part of T701A 202X1110-810Yoke, Deflection
R371203X6104-7512.7k Ohm, * 5%, 1/4W CarbonX355200X8220-851Diode (Zener) RD10EBIx703Diode (SI HV)208X2000-946CRT Socket
R301204X2122-093,Varistor, 250K Ohm, Vert. HoldX366200X8100-130Diode (HS) RU-1 0.3 US297X2000-072HV Uni (1701)
R302204X2114-065,Varistor, 20K Ohm, Vert. Size6A0397Plug, Line Cord
VR351204x2114.059faristor,m, Hor.Ho!9A2753-003

MISCELLANEOUS Degaussing Coll (L701)

CAPACITORS4301204X9300-958Socket, 6 Pin
54302204X9300-958Socket, 6 Pin
C301203%1100-0280:15 UF; SOV, = 10% MylerP301204X9601-195Plug, 6 PinINTERFACE BOARD (P305)
C302203X1100-5730.022.uF, SOV, # 0% MylarFootoeBivrin
304203X1100-8580.1 uF,50V, + 10%Mylar5
308203X0025-0262.2 uF, 50V. ElectrolyticTH301201X0000-534Thermistor(MODEL 13K 4606)
C307203X1100-9280.15 uF, SOV, + 10% Mylar
309203X1100-8580.1 uF, 50V, + 10% Mylar
C310203x0010-01122 uF. 16¥ ElectrolyticTRANSFORMERS & COILSRESISTORSSEMICONDUCTORS

0-089 1000 uF, 35V Electrolytic

eae20270004690.0082 uF, 50V, = 0% CeramicLast201X5200-091Colt, Horlz. Ose.R201340X9010-93491 Ohm, 5%, 1/2W CarbonR20186x0121-001Transistor (NPN)
7R203340X3102-9341/2W CarbonTR20286X0121-001Transistor (NPN)
R204340X2101-9341/4W CarbonTonPeedTransistor (NPN)
R206340X3331.944/, 12 Carbon(0066-00Transistor (PNP)
POWER BOARD (MV)F207340X3102-934tk Ohm, 5%, 1/2W CarbonR20586X0066-001Transistor (PNP)
R208340X3152.9341.5k Ohm, 5%, 1/4W Carbon7onTransistor ba
503203x0010-01122 uF, 16V ElectrolyticR209340X2101.934100 Ohm, 5%,1/4W Carbonransistor (!
RESISTORSC551203X0005-046220 uF, 10V egsteonticR210340X3102-9341k Ohm, 5%,1/2W CarbonTR20886X0121-001Transistor (NPN)
R211340X2331-934330 Ohm, 5%,1/4W CarbonTR20986X0121.001Transistor (NPN)
R501204X 1725-052180 Ohm, + 10%,15\W WWR212340X2331.934330 Ohm, 5%,1/4W Carbon2020166X0040-018Diode, Zener, 6.8v, 5%, 0.5W
R502203X6000-608100 Ohm, + 5%, 1/8W CarbonSEMICONDUCTORSR213340X2331-934330 Ohm, 5%,1/4W Carbon2020266X0040-019Diode, Zener, 3.9v, 5%, 0.5W
R503,203X6000-9601k Ohm, + 5%, 1/8W CarbonR214340X2201.934200 Ohm, 5%, 1/4W Carbon
R504203X6000-879560 Ohm, * 5%, 1/8W CarbonR501200X3174-006Transistor, 28C17400R215340X2201-934200 Ohm, 5%,1/4W Carbon
R505203X9014-96539k Ohm, + 5%, 1W MO.Ax TR502200X3145-404Transistor, 2801454R216340X2201.934200 Ohm, 5%, 1/4W CarbonMISCELLANEOUS
R506203X6500-8426.8k Ohm, + 5%,1/8W CarbonTRSS1200X3172-305Transistor, 2501723R20140X0590-0171.5k Ohm, Black Level Control
R551203X8500-420120 Ohm, + 5%,1/8W Carbonx501201X2230-042Diode, (S!) Zener EQB01-06V201204X9300-958Socket, 6 Pin
VR501204X2050-001Varistor Vert. Adj.x502201X2010-144Diode, (SI) 1S2473-T72CAPACITORSrepairedSocket. & bay

‘ocket, 4 Pin

P201204X9601-195Plug, 6 Pin
CAPACITORSMISCELLANEOUS20145X0524-0381000 uF, 16V ElectrolyticP20220459601 195Plug, , Pin

9600-84! lug, 4 Pin

501203X0040-02010 uF, 160V ElectrolyticJ501204X9300-958Socket, 6 Pin2056A0393-006Plug, 6 Pin
502202X7000-2811500 pF, 50V, + 10% CeramicPs01204X9601-195Plug, 6 Pin
THSO1201X0000-618Thermistor

6-11 6-12

Page 66

‘Blue oneen RED XI01.XI03 and XIOS VIDEO AMP, 25C454C X102,X104 and XI06 VIDEO AMP. 2SA673C Mor=xi03 RG.8 VIDEO OUTPUT, 25c26il or 38cisiav

so, r302 00308 ne ane Isu-3032A | ray SESS enctoas ea B assy

(WEGA TIVE H. SYNCrexsoe—

es asa eve corn J[xa03 exam umiter 25673 304 BLANKING 28C4S4C oracles

X901 POWER DRIVE 2SC 2688 apt X902 ERROR AMP 2SC1890 . —>= ————— os T = ate ie} ow - ae

we t TT aN 7: tas

ST- feTilepiesstan| REIFELfages gee
PPP PP OCD)rstCO FRE poe cupoe rwa—_
wanetHe]T=|za oe
wee |BBDdaye:=

cso) To) HAN244 Ge) Beer] jen Hav osc] | xso1__s.itifan Fol

Schematic Notes Unless otherwise specified Resistance: (Q) (K*KQ, MMQ), 1/4 (W) carbon resistor Capacitance: 1 or higher—> (pF), less than 1-> (yF) working voltage ~> 50 (V) ceramic capacitor Inductance: (v H) Electrolytic Cap: Capacitance Value ( F)/working voltage (V), NP — non-polar (or bipolar) electrolytic cap.

Bat BS, ASSYEF ee ci“Refer to the parts list for additional component information.
Lara TTicy Set a. <a _Qindicates test point connection
28C454C or 2sci6es2SC26iIl or BSC2EIOBK 250869 ormesahindicates chassis ground unless otherwise specified

280820 ACI20V 6OH2/S0Hz Hz _ indicates cycles per second 10% For safety purposes (and continuing reliability) AN replace all components marked with safety syrnbol with identical type.

NOTE: FR - fusible resistor ——¢23-

00-4147-04 Parts identification on circuit boards:

G07-CBO e.g. SU1126A (R107 = R1107) SU3030A (R113 = R3113)

6-13

Page 67

REPLACEMENT PARTS LIST - ELECTROHOME 19”’ MONITOR

special characteristics important to safety. Components identified by the A symbol in the PARTS LIST and on the Schematic have

DO NOT degrade the safety of the set through improper servicing.

Abbreviations for Resistors and Capacitors

Resistor Capacitor

CR: Carbon ResistorC Cap.
Comp. R: Composition ResistorM Cap
OM R: Oxide Metal Film ResistorE Cap.
VR: Variable ResistorBP E Cap.

MF R : Metal Film Resistor

CMF R: Coating Metal Film ResistorMM Cap.
UNF R: Nonflammable ResistorPP Cap.
FR: Fusible ResistorMPP Cap.

PS Cap Tan. Cap. Ceramic Capacitor Mylar Capacitor Electrolytic Capacitor Bi-Polar (or Non-Polar) Electrolytic Capacitor Metalized Mylar Capacitor Polypropylene Capacitor Metalized PP Capacitor Polystyrol Capacitor Tantal Capacitor

NOTE: When ordering replacement parts please specify the part number as shown in this list including part name, and model number. Complete information will help expedite the order.

Use of substitute replacement parts which do not have the same safety characteristics as specified, may create shock, fire or other hazards. For maximum reliability and performance, all parts should be replaced by those having identical specifications.

SERVICE REPLACEMENT PARTS LIST

Symbol Description Main P.C.B. Ass'y CRT Socket P.C.B. Ass’y Purity Shield Ass'y

6-14 Part Number SU-1133A SU-3032A 07-220083-03 Outside of the P.C.B. Ass’y Symbol Description Picture Tube 19” a A\Deflection Yoke PC Magnet A A\Flyback Transf. A AHVR ROS UNF Resistor 2200,25W K C04 C Capacitor 150pF, AC1.5KV x01 Si. Transistor x02 Si. Transistor sc Screw #8-% sc Screw % x % Pix Tube Mtg. (4) WA Pyramidal Lock Washer (4) Nut Retainer, Pix Tube Mtg. (4) Clip — P.C.B. Support Standoff Wire Terminal (Gnd. Strap) Terminal Lug (Gnd.) Groundstrap Assy. Grounding Spring Wire Hook (Gnd. Strap) Purity Shield Holddown Clamp Support Brkt. RH Support Brkt. LH Chassis Base Yoke Wedge (3)

Purity Shield Ass’y. Parts List

Symbol Description Degaussing Coil D911, D912 Rectifier 1 Amp 600V (2) Pin Terminal (2) Pin Terminal Housing Purity Shield (2 pcs.) Purity Shield (2 pcs.) C911 Capacitor 100nF 10% 400V R921 Resistor, Wirewound 330, 4W Fire Retardent Term. Strip 4 Lug

CRT Socket P.C.B. Ass’y (SU-3032A) Parts List

Resistors Symbol Description

R3105VvR 200
R3106VvR 200
R3113VvR 5K
R3114VvR 5K
R3115VvR 5K
R3116OMR 10KQ2W J
R3117OMR 10K Q2W J
R3118OMR 10KQ2W J

R3119 Comp. R 3.3KQ%W K R3120 Comp. R 3.3KQ2%W K C3121 Comp. R 3.3KQ%WK

Capacitors Symbol Description C3107 E Cap. 10uF 250V A C3108 C Cap. 100QpF DC1400V P

Coils Symbol Description L3101 Peaking Coil

6-15 Part Number 17-7198-03

A29951-B A46600-A QRF258K-221 QCZ0101-005 2SD870 2SC1106A, 31-610818-06 31-601418-12 33-255-01 33-494-01 33-629-02 33-670-010R-02 34-228-03 34-33-04 34-574-02 35-212-03 35-3053-02 35-2348-01 35-3890-01 35-3890-02 38-449-02 39-1233-01

Part Number 21-1007-30 28-22-27 34-708-01 34-709-01 35-3847-01 35-3847-02 48-171544-62 42-113301-03 34-492-09

Part. Number QVZ3234-022 QVZ3234-022 QVZ3234-053 QVZ3234-053 QVZ3234-053 QRGO029J-103 QRG029J-103 QRGO029J-103 QRZ0039-332 QRZ0039-332 QRZ0039-332

Part Number QEWS3EA-106 QCZ9001-102M

Part Number QQL043K-101

Page 68

Semiconductors Symbol X3101 X3102 X3103

Miscellaneous Symbol aA Description Si. Transistor Si. Transistor Si. Transistor

Description AXCRT Socket

Main PCB Ass’y (SU-1133A) Parts List

Resistors Symbol R1406 R1408 R1410 R1414 R1415 R1421 R1422 AFR1401 AR1503 R1504 R1509 R1512 R1514 R1515 R1522 R1523, R1528 R1534 VR1501 AR1703 AR1704 A\R1901 R1902 R1903 R1904 R1905 4Q1908 ASR1909 R1910 ASFR1901

Capacitors Symbol C1301 61402 1407 C141 C1412 C1508 Ac1512 Ac1513 ACI514 C1515 C1520 C1523 C1524 AC1531 AC1532 1904 C1905 Description Vv v CMF OM Om om v AF ACMF v Om OM om CMF CMF OM Om ZN ZN ACMF AXCMF APosistor UNF CMF OM OM CMF Vv A\CMF AF DVDDDVDVDDYD DVDVVDVVVVBVVVVVVIVVMD 2002 6.821W J 3.3K QIW J 27K Q1W J 12KQ2W J 10KQ. 6822W K 11.8KQYUW +1% 5KQ 10K Q2W J 8.2KQ2W J 82022W J B.201W J 4.791W J 6822W J 39021W J

B9QUW +1% 7.68KQ. YAW +1%

2Q7W K 4703W J 1OKQ2W J 18K Q1W J 47 QW +1% 2kKQ 274K QW +1% 2202%W K

Description BPE Tan. E E E PP Ape APP AspP PP BPE E M APP APP E E Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. . 3.3uF 50V A . 2.2uF 16V K 47uF 6.3V A 100uF 160V A 3.3uF 160V A 5600uF 50V J 2000pF DC1500V J 2000pF DC1500V J 2000pF DC1500V J 0.53uF DC1200V J 3.3uF 50V A uF 160V A O.1uF 200V K 2000pF DC1500V J 1500pF DC1500V J Cap. Cap. 10uF 250V A Part Number 28C1514VC 2SC1514VC. 28C1514VC

Part Number A76068

Part Number QVZ3230-002 QVZ3230-002 QRX019J-6R8 QRG019J-332 QRGO19J-272 QRGO26J-123Z QVZ3230-014 QRH024K-680M QRV142F-1182 QVZ3230-053 QRGO26J-103Z QRGO026J-822Z2 QRG026J-821Z QRX019J-8R2 QRX019J-4R7 QRG026J-680Z QRG019J-391 ERZ-C05Z2K471 ERZ-CO05DK271 QRV122F-3902 QRV142F-7681 A75414 QRFO76K-2RO QRX039J-4R7 QRG026J-103Z QRGO19J-183 QRV122F-470Z QVPS5A0B-023E QRV142F-2741 QRH124K-221M

Part Number QEN61HA-335Z QEE51CK-225B QEW51JA-475 QEW52CA-107 QEWS2CA-335 QFP31HJ-562 QFZ0082-202 QFZ0082-202 QFZ0082-202 QFZ0067-534 QEN61HA-335Z QEW62CA-105Z QFM720K-104M QFZ0082-202 QFZ0082-152 QEY0034-001 QEWS2EA-106

Page 69

Coils Symbol L1502 L1503 L1504

Transformers Symbol T1501 T1503

Semiconductors Symbol 101501

X1101 X1102 X1103 X1104 X1105 X1106 X1301 1302 X1303 X1304 X1305 X1401 X1402 X1501 X1901 X1902

D1101 D1102 D1103 D1301 D1401 D1402

D1503 D1504 D1505 D1506 D1507 D1508 AD1701 A\D1901 AxD1902 A\D1903 A\D1904 AxD1905

Miscellaneous Symbol A\F1901 A\F1902

Description Part Number

Linarity Coil A39835 Width Coil C30380-A Heater Choke C30445-A,

Hor. Drive Transf. A46022-BM Side Pin Transf. C39050-A

Ic HA11244

Si. Transistor 2SC1685(R) Si. Transistor 2SA673(C) Si. Transistor 2SC1685(R) Si. Transistor 2SA673(C) Si. Transistor 28C1685(R) Si. Transistor 2SA673(C) Si. Transistor 28C1685(R) Si. Transistor 2SC1685(R) Si. Transistor 2SA673(C) Si. Transistor 2SC1685(R) Si. Transistor 28C1685(R) Si. Transistor 28D478 Si. Transistor 28D478 Si. Transistor 2SC2610BK Si. Transistor 2SC2688 (K.L.M.) Si. Transistor 2SC1890A (E.F.) Si. Diode WO6A Si. Diode WO6A Si. Diode WO6A Si. Diode 1SZ473H Si. Diode 1SZ473H Zener Diode RD10F(C) Si. Diode HF-1 Si. Diode VO9E Zener Diode RD11E(B) Si. Diode WO6A, Si. Diode 1SS81 Si. Diode 1SZ473H AsZener Diode RD20EV2 ASi. Diode 1S1887A ASi. Diode 181887A ASSi. Diode 181887A ASi. Diode 181887A AdZener Diode RD6.8EV3

AFuse 1.254 QMF53U1-1R25S AXUL Fuse 3A QMF66U1-3R0S

6-17

Page 70

ICol POWER REGULATOR == SU-1103A MAIN PCB ASSY so steen sue XIOL £103 and XIOS VIDEO AME. 2508546 or 2501685 TOl=X103 RGB _VIGEO OUTPUT Es av

SYN

303 BEAM LIMITER 2SA673 3308, BLANKING 28ca:

x30a 301x302, 4305,x306 ca 330540 or escisas | x102.X104 and XI06 VIDEO_AMP 2SA673¢

oi]

i | wie ic pal

2soa7a

Ic 50 Nati2a4 Od Ware fang Hav osc TT wet

XS01 HORIVE Kol 4 our 28cis07 WD, 2scaa7iv 20898 or PROTECTOR 25C434C or 25C 1685

AcizOV 6ora/sone 210%

6-18 28¢261 or 28C26i08K 250869 Schematic Notes Unless otherwise specified Resistance: (Q) (K--KQ, M--MQ), 1/4 (W) carbon resistor Capacitance: 1 or higher-> (pF), less than 1-> (yF) working voltage -» 50 (V) ceramic capacitor Inductance: (» H) Electrolytic Cap: Capacitance Value (v F)/working voltage (V), NP - non-polar (or bipolar) electrolytic cap. Refer to the parts list for additional component information. 2 indicates test point connection hy indicates chassis ground unless otherwise specified Hz _ indicates cycles per second For safety purposes (and continuing reliability) b& replace all components marked with safety symbol with identical type.

NOTE: FR ~ fusible resistor —g2—

Parts identification on circuit boards: e.g. SU1126A (R107 = R1107) SU3030A (R113 = R3113)

Page 71

REPLACEMENT PARTS LIST - ELECTROHOME 13” MONITOR

Components identified by the A\ symbol in the PARTS LIST and on the Schematic have special characteristics important to safety.

DO NOT degrade the safety of the set through improper servicing.

Abbreviations for Resistors and Capacitors

Resistor

CR Comp. R OM R VR MF R CMF R UNF R FR Capacitor

Carbon Resistor C Cap. Composition Resistor M Cap Oxide Metal Film Resistor E Cap. Variable Resistor BP E Cap. Metal Film Resistor : Coating Metal Film Resistor MM Cap. Nonflammable Resistor PP Cap. Fusible Resistor MPP Cap. PS Cap Tan. Cap. Ceramic Capacitor Mylar Capacitor Electrolytic Capacitor Bi-Polar (or Non-Polar) Electrolytic Capacitor Metalized Mylar Capacitor Polypropylene Capacitor Metalized PP Capacitor Polystyrol Capacitor Tantal Capacitor

NOTE: When ordering replacement parts please specify the part number as shown in this list including part name, and model number. Complete information will help expedite the order.

Use of substitute replacement parts which do not have the same safety characteristics as specified, may create shock, fire or other hazards. For maximum reliability and performance, all parts should be replaced by those having identical specifications.

Symbol

Outside of the P.C.B. Ass’y Symbol Avot AXDYO1

ARI A\ROS Aco4 x01 1co1 Lo1 Description Main P.C.B. Ass'y CRT Socket P.C.B. Ass’y

Description AsPicture Tube A\Deflection Yoke PC Magnet Wedge A\Flyback Transf. AFocus V R UNF Resistor 22022, 25W. K AC Capacitor 150 pF, AC1.5KV Si. Transistor IC Regulator Degausing Coil Degausing Coil Pin Terminal (2) Degausing Coil Pin Terminal Housing Groundstrap Ass'y. Groundstrap Wire Terminal Groundstrap Spring (2) Support Bracket RH Support Bracket LH SCREW 10-% Pix Tube Mtg. (4) Pyramidal Lockwasher (4) Clip P.C.B. Support (2) Ground Lug Chassis Base

6-19 Part Number

SU-1103A SU-3016A

Part Number

370ESB22(E) C29123-V A76366-A 30006 A19183-A. A46606-A QRF258K-221 QCZ0101-005 2SD869 STR383 21-1007-31 34-708-01 34-709-01 34-697-04 34-228-03 35-3560-01 35-3919-01 35-3919-02 31-631018-08 33-255-01 33-629-02 34-33-04 38-452-01 Main P.C.B. Ass’y (SU-1103A) Parts List

Resistors Symbol R1406 R1408 R1410 R1414 R1415 R1421 R1422 AXFR1401 A\R1503 R1504 R1509 R1511 R1514 R1515 R1522 R1523 R1528 R1534 VR1501 A\R1703 AXR1704 AXR1901 R1902 R1903 R1904 AXFR1901

Capacitors Symbol C1402 C1411 C1412 C1508 C1511 AC1512 AC1513 AC1514 C1515 C1520 C1524 C1904 C1905 AXC1907

Coils Symbol L1501 L1502 L1503 L1504 L1901

Transformers Symbol 71501 T1503 Description Vv R 2002 Vv R 2002 CMF R 6891W J OM R 3.3KQ1W J OM R 2.7KQ1W J OM R 12KQ2W J v R 10KQ AF R 6822W K ASCMF R= 11.8KQYW +1% Vv R 5KQ OM R 10KQ22W J OM R 5.6KQ2W J OM R 68022W J CMFR 82Q1WJ CMF R 4.7Q1WJ OM R 562Q2W J OM R 39021WJ ZN R ZN R AXCMF R 39K QW +1% AXCMF R_7.68K QYW +1% APosistor UNF R 2Q7WK CMF R 5.623W J OM R 10KQ2W J AF R 2202 %W K

Description Tan. E E PP E APP APP APP PP

M E E Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. BPE Cap. Cap. 2.2uF 16V K 100uF 160V A 3.3uF 160V A 5600pF 50V J 47uF 160V A 2000pF DC1500V J 2000pF DC1500V J 2500pF DC1500V J 0.53uF DC1200V K 1uF 50V A 0.1uF 200V K Cap. Cap. A\MM Cap. 10uF 250V A O.1uF AC150V Z

Description Peaking Coil Liniarty Coil Width Coil Heater Choke Line Filter

Description Hor. Drive Transf. Side Pin Transf.

6-20 Part Number QVZ3230-022 QVZ3230-022 QRX019J-6R8 QRGO019J-332 QRGO019J-272 QRG029J-123 QVZ3224-014H QRH024K-680M QRV142F-1182 QVZ3230-053 QRGO029J-103 QRGO029J-562 QRG029J-681 QRX019J-8R2 QRX019J-4R7 ORG029J-560 ORGO19J-391 ERZ-C05ZK471 ERZ-C05DK271 QRV122F-3902 QRV142F-7681 A75414 QRFO76K-2RO QRX039J-5R6 QRG026J-103Z QRH124K-221M

Part Number

QEES1CK-225B QEWS52CA-107 QEW52CA-335 QFP31HJ-562 QEWS2CA-476S QFZ0082-202 QFZ0082-202 QFZ0082-252 QFZ0067-534 QEN61HA-105Z QFM72DK-682M QEY0034-001 QEWS2EA-106 QFZ9008-104

Part Number A75360-6 A39934 C30380-A C30333-A A39475-J

Part Number A46022-BM 39050-A

Page 72

Semiconductors Symbol 101501

x1101 x1102 X1103 X1104 x1105 X1106 x1301 x1302 X1303 x1304 X1305 x1401 x1402 X1501 x1701 D1101 01102 01103 01301 01401 01402 01503 D1504 D1505 D1506 D1507 1508 4801701 4xD1901 AxD1902 A\01903 4301904

Miscellaneous Symbol ASF 1901 AF 1902 Description Lc.

Si. Transistor Si, Transistor . Transistor . Transistor Transistor |. Transistor . Transistor i. Transistor i. Transistor i. Transistor |. Transistor . Transistor i. Transistor i. Transistor i. Transistor i. Diode Diode |. Diode i. Diode i. Diode Zener Diode Si. Diode Si. Diode Zener Diode Si. Diode Si. Diode Si. Diode AsZener Diode ASI. Diode ASi. Diode ASi. Diode ASSi. Diode

Description AsFuse 1A ASUL Fuse 3A

6-21 Part Number HA11244

2SC1685(R) 2SA673(C) 2SC1685(R) 2SA673(C) 25C1685(R) 2SA673(C) 2SC1685(R) 2SC1685(R) 2SA673(C) 28C1685(R) 2SC1685(R) 2SD478 2SD478 2SC26108K 2SC1685(P-S) ‘WO6A ‘WO6A WO6A 182473H 182473H RD10F(C) HF-1 VOQE RD11E(B) ‘WO6A 1SS81 1S82473H RD20EV2 1$1887A 181887A 181887A 181887A

Part Number QMF53U1-1R0S QMF66U1-3R0S

Page 73

CRT Socket P.C.B. Ass’y (SU-3016A) Parts List

Resistors Symbol R3105 R3106 R3113 R3114 R3115 R3116 R3117 R3118 R3119 R3120 R3121

Capacitors Symbol C3107 C3108

Coils Symbol 13101

Semiconductors Symbol X3101 X3102 X3103

Miscellaneous Symbol A Description v R 2002 v R 2002 v R 5KQ Vv R 5KQ Vv R 5KQ OM R 10KQ2W J OM R 10KQ2W J OM R 10K22W J Comp. R 3.3KQ%W K Comp. R 3.3KQ%W K Comp. R 3.3KQ’%W K

Description E Cap. 10uF 250V A C Cap. 1000pF DC1400v P

Description Peaking coil

Description Si. Transistor Si. Transistor Si. Transistor

Description A\CRT Socket

6-22 Part Number QVZ3234-022 QVZ3234-022 QVZ3234-053 QVZ3234-053 QVZ3234-053 QRG029J-103 QRG029J-103 QRG029J-103 QRZ0039-332 QRZ0039-332 QRZ0039-332

Part Number QEWS52EA-106 QCZ9001-102M

Part Number QQL043K-101

Part Number 2802611 28C2611 2802611

Part Number A75522

Page 74

| Vil Schematics and Wiring Diagrams |

Page 75

La a oa L r el L_ a4 pecs [t------- s Pa a & B « 1084-90414 ~¢9"5

LaGIc_GNO,

LOGIC _GND.

1 Slon set- ese ‘SELECT

Ler see er rar

=VIOM CONTROL GND.

RED me aE

aH

q = r

'

I RAPID FIRE. BD. PC A084 -7H410~-A000 MONITOR POWER JACK

al BULB Fi5TB-cw. ON-OFF SW.

BANe

{40.10 manson eOWIROL,CONEERON-OFF Sw + SHR.

SCHEMATIC MOS!~00508-A003 GALAGA UR.

REVISIONS, nian 2 fa, [meets {a

NOTES. LINE, FILTER BW

2 BLU-GRY

{ Leer "

BlU-cRY.

; i i 4 1 1 RE ] | gi boo Ge 8 oo = Fd i rot 4 ud CTT KH 1 4d a re eo. or, rr a oi nes AA in ~ eee | lp 2 see

: i ne ae Aq = “4-4 - 4. - 5 daa

Peoe td 3 * x a Fy g

Is l 8

7A

Page 76

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 77

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 78

DESIGNATION

ec. ce c3 ca cs ce cr?

al R2 RS Ra RS Re

vri

Di, pe bs 04,05 De-po DI0

er a2

ut v2

ul HsI Fl F2 FS

FCIA,FCIB,FCZA FC2B,FCSA,FC3B

al v2

MHal

Haz

wHut

Twi-TW3 DESCRIPTION

10000 MF 38V AX. ELEC. LOIMF SOV AX. CER, IMF 26V TANT. 20000 MF I6V AX. ELEC. IOOPF SOV AX. CER ATOMF I6V AX. ELEC. 4700mF 26v " *

470 OHM I/4w 5% CREW 0" ame seo pr io

Oo OHM I74W CRBN.FLM.

AlQF Ing004 MR750 AISF AlaE

PSI 2N3055

LM 3i7 3832

FERROXCUBE BEAD HEAT SINK FUSE 2A “a "ea

FUSECLIP W/ STOP

CONN. KK.I56 (RA)(S~PIN) (6-PIN) "CRAM S-PIN) (13-PIND

MOUNTING HAROWARE QI

  • SCREW 4-40X10 SLT RND
  • WSH.4 120-250-018
  • HEXNUT 4-40
  • SHOULDER WSH. 974-302 THERMAL COMPOUD AS REQ.
  • TO- 220 INSULATOR RT-3.5MICA MOUNTING HAROWARE 2
  • SCREW 4-40XI0 SLT RND
  • WSH4 120-. 250-018
  • HEXNUT 4-40
  • SHOULDER WSH. 974-302 THERMAL COMPOUD AS REQ (WD To-3 RT- 1.8 FILM

MOUNTING HARDWARE UI

  • SCREW 4- 40X10 SLT RND (SH 4 120-280-018 (OHEXNUT 4- 40 () SHOULDER WSH. 974-302 THERMAL COMPOUD AS REQ
  • TO-220 INSULATOR RT- 3.5 MICA TIE WRAPS J2

Jl FI roig roe oy td ul

ee

Ri] cr + @®

nTWS Ca)

ire | — EC2A {| cae = ul

[re ane Ra Ces

  • +)

FC3A

+ few +i D7 | | = cr + fe i com om P ut |, MAUI

HEAT SINK

°

MHO2 A %? N (2)

O] «_MHa!

M051-00935-Co28

UNLESS OTMERWISE SPEC concentmicity Ti

ance me DESCRIPTION

100 PF 50v AX.CER OiMF * * 1MF 25v TANT 470MF " AX.ELEG 4700MF * 0" 10000MF 35v AX.ELEC. 20000 16v MF" *

10 OHM 1/4w 5% CBN

100"os8

470 © 8

B10"68
S60"*#+
2TKe6we

109 * CBN FLM

1N4004 A14F ASE MR750

TIP31 2N3055

3532 M317

FERROXCUBE BEAD

HEAT SINK

FUSE 2A FUSE 6A FUSE 8A

FUSECLIP

KK 156 (RA) (5) KK 156 (RA) (6) KK 156 (RA) (13)

SCREW 4-40x10 WSH 4 120-.250-018 HEXNUT 4-40 SHOULDER WSH THERMAL COMPOUND TO-220, INSULATOR TO-3 INSULATOR TIE WRAPS ae WEES Gosden

°

Oanpreee aan DESIGNATION

FO1A,FC1B,FC2A, cs c2 c3 ce c7 C1 ca

Re R2 RI RS Ra Ra

vR1

01,02,010 D6-D9 04,05

a1 a2

u2 ut

ua

Hs1

FA F3 F2 PART NUMBER

0171-043H6-JXVX 017 {-097H2-JXXX 0935-008 14-0100 0175-27 1EX-EXXX 0175-3 14EX-EXBX 0175-322GX-EXBX 0935-008 14~0800 0062-05 1B3-1XXXx 0062-11083-1XXXx 0062+ 156B3-1xXXXx 0062-159B3-1XXxXx 0062-162B3-1XXX 0062-199B3-1XXxx

0063-025AX-1DEX 0508-0080 1-0200 0064-168XX-XXGX 0064-169XX-XXGX 0064-303XX-XXJX

0065-485XX-xXXX 0935-00800-0000

0066-04 4BX-XXXX 0935-00804-3600

0917-00009-0225

0068-045Xx-ABDX

0017-00003-0005 00 17-00003-0008 0017-00003-0184

0017-00003-0214 FC2B,FC3A,FC3B

J1,d2 3000- 16387-0500 a 3000- 16387-0600 J2 3000- 16387-1300

MHU1,MHQ1,MHQ2 0017-00101-0727

ns"0017-00104-0071
ae:0017-00 103-0002
os.0017-00042-0 109
"oeJ0017-00009-0204

MHU1,MHQ1 0017-00003-9205, MHQ2 0017-00042-0108 TW1-TW3 0017-00042-0105,

THIS DG 1S CONFIDENTIAL & PROPERTY OF MIDWAY MFG CO MIDWAY MFG. Co, FRANKLIN PK IL 40131

POWER SUPPLY Abaicy co

7-4 REVISIONS O84 -FON1SY C4935

Page 79

Jif ro a Al4F x2 LM3i7 -Jt

ar2a FUSEUlr7

t t mM 1 s +7.2V 2AMP MAX. '7 '+7.2V COIN METERS

1 1 ' 1 ' key ! 16 ' cs 1 > | + | IMF 25V ' 1

TANT11

__] an ' 1

— MT87''
KX2N3055U7'+5V SAMP. MAX.
— MT9Iae fusea2FERRITE BEADhe,
ut419+5V

sv >

4++N\yTele sv
@3R411
256011
=x''
785cét1
+86+'1

fe}

34S1004TOMF 16V11
awELEC.AX.ii
t''
°1t
R51‘
510i1

1 1

to'!
RE'1

+

1 1 1 + VAIND.= 3.5AMP _ 3 IOV RMS AT

DI0'lev.= I3V AT I.SAMP
rtAuDIO
°orAl4Fii
Cc?1t
AISF X4+La700me 25v'1
ELEC AX.J'

1 1a

bs12Vv. AUDIO

' tev. u IND

te -wJ DISPLAY L | Lites

NOTES: % 2AMP FUSE W/O DISPLAY LITES %*% MT87 FOR UR.

MT9I FOR C.T. SCHEMATIC: MO5I-00935-CO25 useo on GALAGA MIDWAY MFG. CO. REVISIONS

DO NOT SCALE ows Ful LL NO REQ | PER ‘Dim, TOLERANCES

parei- 1 - Bl POWER SUPPLY A084-90414-C935

Page 80

DESIGNATION

ct ce

c4-c2i

2c

ze 2F.2H,2,2K au 2m 2N 3A

3C,30 3E,3F,3H.30.3K. 3M

4a an.ac

ar an au am 5A se DESIGNATION LIST

04xx CUSTOM IC STATIC RAM (2KX8) 00XX CUSTOM | o7xx * . 74.820 74.8273 7aLs377 7aLs273 74.245 7aLs273 74Ls377 6-4 PROM(256x 4) 7aLs20 vats TaLs2e3 2114-2 RAM(IKX4) 7aLs00 maLs368 74Lsi87 TaLse6 Gc-L EPROM (4096x8) cs-x * ij 02xXx CUSTOM IC GG-y EPROM(4096x 8) O8xX CUSTOM Ic 74LS365 7aLs298

DESCRIPTIONDESIGNATIONDESCRIPTION

ATO MF I6V Ax ELEC. IG 5¢,90,96.9F.5H.5y 7ALSI6!

OOIMF SOV CERTox7acs259
220PF_SOOV *8% MICADsTavs20
IMF SOV CER[oom7aL8287

oN (60-5 PROM (32x “6A 74.8365 : “VIDEO RAMKIT"=" OPTION I”

‘e20 ot ifaw 9% cRBM_IVIDEO RAM KIT" - “OPTION 2”
woke:DEO RAM KIT" =" OPTION |”
oem:VIDEO RAM KIT" -"OPTION 2

meee vase

zo 7otof
aorotorfIgsocKeT
wotooforotmar.
oo 7ttfok24-PIN
aocosotf“tn2e-rN "
iw¢ffstan16-Pm*
so"ofors* SE,SF.3H.3U3K.3L 18 -PIN:
wono aD.aree

"an ze-pN St "ata 2a-pm TT

2.2K om 8-yNIT 9- PIN SIP* oyem ee

1K OHM 4-UNIT 5-PIN. SIP

ut CONN R.A. HEADER 50- PIN v2 CONN: PCB HEADER 6- PIN

ratsisMaI- MH4DUAL LKG PCB SPACER
SG°3 PROM (256 x4)pce‘A080- 91405-8508

741808 TaLSI36 Tas32 As BELOW

PLUG- SOCKET CONNECTOR 50- PIN RIBBON CABLE- .33FT 50- CONNECTOR 28GA. STRND.RND. CONDUCTOR CABLE \ caste ASSY /

CROSS REFERENCE LIST

, | ; i

> (THe i] een

a Tre fe 1k sor rend

ume we im

DESCRIPTIONQUANTITYDESIGNATIONPART «=
220PF SOOV 45% MICA CAP130508-006¢7- 100
OOIMF SOV CER CAP1ce0508-00800-0200
ime”iia!c4-c2i
+A7OME I6V AX. ELECtcl(0808-00800-0400
Fa100 OHM 1/4W 5% CRON RES\Rio0062- 11008-1xxx
nezo"*ot3RLRS.RE
sootoTof ohot\Rv
470baR2.R4,R7,RII-RI4
aa]moon10R5,RO.RO.RIS,RIG,

= |? RIB-R22

hdIK SIP (4-UNIT) 5- PIN30508- 00804-0100
1k SP (O-UNIT) 9- PIN10808- 00804-0200
L22K.so40508 -00804-0300
an8©Oxx custom i¢'0066-001cx- KAPX
O2Kx-“10066~- OO2CX- XAPX
O4KX.“10066 - OO3CX -XAPX
zOSKX..1Icom0066 -O04CX-XAPX
OTXX".1CIN0066 - OO6CX-KAPX
2114-2 ST.RAM 200NS.(1024x4)«610 3E,3F.3H,34.3K,3L00803-0300
74L8001ica= 00803-0400
raso81rc1D
74.8203C28, 30,5
7as3z1\cir
,rats064(C38,48,4C.6N
e,[VeTALSI38itele
iI7aLSi83trg
74L8i871can
Tatsi61‘156,80, SE, 56.54.54
,*74.82454IC2F, 2H, 20,2K
7482871icsm00803-1400
Tavs259‘iesk00803-1500
oS741827331e20, 26,200808-00803-1600
=7acsze321e3c,3000803-1700
os74.829811c5B‘00803-1800
wee74183652Ica, 6a00803-1900
aTaLs361c3N00803-2000
774.93772120, 2M00803-2100
66-3 PROM (256x4)Hlrete00803-2900
cc-4 *“11c2n00803 -3000
66-8 PROM (32x8)'can00803-3100
66-4 EPROM (4096 x8)iteat00803-2600
oo-K *.1car0508- 00803-2700
oo-L *hl'1c4D0508- 00803- 2800
3STATC RAM (2KX8)\ik(0808- 00803- 2500
*"VIDEO RAM KIT'MAIN PHATOM0508- 00803- 4000
‘* OPTIONI”1SUB PHATOMNOT RELEASED
~ 2148 RAM (IKX4)21C 6B,6K(IN ABOVE NUMBER)
?OPTION 2"1SUB PHATOM0808-00803- 2200
= 2147 RAM (4KX1)s1c 6¢, 60.66, 6F,(im ABOVE NUMBER)

IC 6, 8K,6L.6M 8 ‘MOTE: ASSEMBLY TO INCLUDE EITHER "OPTION|" OR" OPTION2” 2 ASPER LATEST RELEASED B.0M

2 §16 PIN 1¢ SOCKET3161, 2N.5N0808-00804- 0700
—+ie-Pin‘ICS 36,3°,3H,30.3K,8. _0808-00804- 0600
oo5ICSIK,40.4F.4.4M0808 -00804- 0500
20-PIN4e3i4, LN, 440808-00804-0400
CONNECTOR-R.A. HEADER 50-ANIut0508-00804-0800
CONNECTOR - PCB HEADER &-PIN120017-00021-0424

MOUNTING HARDWARE -

DUAL LKG. PCB SPACER‘HIMo017- 00042-0283,

pce "GALAGA" VIDEO P.C.8 AQBO-91405-B508

LE ASSEMBLYCABLE ASS'YA508-00027-0000
PLUG- SOCKETCONNECTOR20508-00804-0900

RIBBON CABLE - .33FT 30-CONDUCTOR 286A, STRND AND CONDUCTOR

ASSEMBLY Mo! PROJECT ENG. JERRY SZERSZEN [sco on GALAGA -00801 1007

FULL PER MIDWAY MFG. CO. 0017-00033-0346

7-6 GALAGA VIDEO PC [A084-91 405-85 08

Page 81

|Faew 7

=

i] wore MEL SC6y : = wwe Sst

= = Eieid

= = Loc. 68.

: 1

if "7 ie |

= 3 on

ts | at =

Page 82

DESIGNATION LIST

DESIGNATION DESCRIPTION DESIGNATION DESCRIPTION DESIGNATION DESCRIPTION

szowe (ov ax evec weap rarsiss ‘Sime Sov cen oe tae

lowe wey ax ecec

oee uF Sov 10x cen

roms aw 9% CRON OW Va cape por UP

noi

jase? Be.2n24.21 Seavacatoun

Con.” Reb READER +r

MOUNTING NAROWARE

‘A090-81404-C908 GALAGA CPU F.c.0 DESCRIPTION quantity CROSS REFERENCE LIST DESIGNATION PART? DESCRIPTION

1% om POTENTIONETER

totes

Tete

bore ‘

‘9808-00004 0800 QUANTITY. DESIGNATION PART

2017-00103- 0008 Sorr-eotar- oat TNasneaw a exrst 2 ‘So'7- goto -eoT!

= 20801-2400

ee = mosteT ENG: JOMRY SZERSZEN _ [n=Gacaca | MNDWAY MFG. CO. Fou [en 1per Pesci

GALAGA CPU PC ln0e4-91 404-c508|

a

Page 83

ly wiht

tN abv eee

Wel

Page 84

DESIGNATION LIST_ -DESIGNATION_ DESCRIPTION CROSS REFERENCE LIST

70) A082 -9:1-4:1:0-A-00.0]

DESCRIPTION_QUANTITYDESIGNATIONPART #,
cl.c2.IMF 100V MYLAR-OIMF 25VAXCER5C3-C70508- 00800-0800
C3-C7.OIMF 25V AX CERz+ IMF IOOV 10% MYLAR=cl,c20508 -00800- 2300
RI-R4IMEG OHM |/4w 5% CRBN RESid68 OHMI/4w 5% CRBN RES. 2R6,RS0062-098B3- IX Xx
RSik"ares“=lioeKoBee2R5.R79962-I79B3- IXXXx
REee"i.a5elelele|SIMeo" "" ""4RI-RA0062-32383" IXXX
aLEaee=|Jou] | | umsse'out0508 - 00803-5500
mSUSU| 74001u20508 -00803-5600
a0 |o fp:
ulLM556°S| co.O 0 KK.156 CON. (2-PIN)2¢ JlW23000-16335-0200
v27400zs(6-PIN)= 2lu3000-16335-0600

Zz r+

a=:MOUNTING HARDWARD
HoveKK1S6) WERT) 2(62PIN) te FIN)‘SNAP BUSHING I/4" = 4MHI-MH40017-00042-0014
WAU MSSNar eusHiNe, 174RAPID FIRE P.C1A080-91410-A000 A080-91410-A000

ASSY MOSI-OOII4-AOO! PROJECT ENG: JERRY SZERSZEN THIS DWG. 1S SONFIDENTIAL & PROPERTY OF MIDWAY MFI

anusssomenuse sec, PaGALAGAMIDWAY MFG. C'
cOncenTmigny tm oo2FRankun PKee

ErAGTONAL 64 REVISIONS:

HOLE DIA“+ 002-000RAPIDFIREP.C.petra:

ANGGO NOT SCALE Owa

Page 85

Sv | Sy ‘AS at — 1 MEG OHM 1 MEG OHK

ors. L NOTE: USE JI

Az FOR RAPID 1 MEG CHM FIRE OPTION

rst a1 MF MYLAR 10%

NOTE: USE J2 TO BYPASS SPFIB ARE

MOS1 -00114~A002

08 NOT SCALE ONG.

MIONAY MFG. CO. FRANKLIN PK. ILL. PART NO. APIO FIRE P.C. Ae2-91410-AD00

Page 86

7-12 ~—__KEY 1 BETWEEN CONTACTS 5,£ AND 6,F KEY 2 BETWEEN CONTACTS 3,6 AND 4,D

DESIGNATION DESCRIPTION o MF AXCER 2-05 47 PF AXCER C6, C7 470 PF AXCER acts 100 PF AXCER 14-032 .01 MF AXCER Lt-La CHOKE 10.UH W.W. MILLER J

Ls-L8 CHOKE 10. JH W.W. Letra CHOKE ENCAP 1C.UH a P.C. EDGE CONN. rg

2,43 3PIN HEADER, 455 6 PIN HEADER J1M.H. 2 EDGE CONN. KEY ee an DESCRIPTION ‘QUANTITY DESIGNATION PHANTOM NUMBER: DESCRIPTION QUANTITY DESIGNATION PHANTOM NUMBER 47PF 50V AXCER 2.05 0508-00800-1800 3 PIN HEADER 2 J2J3 0017-00021-0443

100PF S0V AXCER C8-C13, 0508-00800-1600 AMP 350429-1 TrOPr OOV AXGER ‘50e.00900-1700 , “cost, SIME 2B ANGER Grecee — epoe-a0s0e 1000 SPIN HEADER 2 wes 0017-0021-0424

SMP SOV AXGER a coe 00000-0000 10H W.W. RE Lt-L4 0067-921XX-XXAX PG EDGE CON KEY 2 J1MH 0017-00021-0396

CHOKE MILLER: 6-32x10SLOT 2 JIMH (0017-00101-0574

10.UH WW. PF 4 L518 '9508-00804-2000 Eo”

a= OES Cm CD ; =r (aren) = oz

songs 10.JH ENCAP 4 L9-L12 (0508-00804-2100 WSH6 2 JIM (0017-00104-0002

PF CHOKE 145-,250-.032

PC EDGE CONN. 1 a 0017-00021-0418 BRKT- 1 JaMH 0866-0018-00XF

CONN. FIN ASSY. DWG M051-00508-8014 PROJECT ENGINEERL. DEKKER “THis OWG_'S CONFIDENTIAL £ PRORERTY OF MOWAY WEG CO | MIDWAY MFG. CO. FRANRLM PKG ILe1sH“AbALLYCO TREVISONS panne a | 0-8-4 -2-1-60-8 -B:5-08

GALAGA FILTER PC

Page 87

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 88

GALAGA LOGIC BOARD

CHIP NUMBER FUNCTION 74LS00 Quad 2 Input Nand 74LS08 Quad 2 Input And 74LS10 Triple 3 Input Nand 74LS20 Dual 4 Input Nand 74LS32 Quad 2 input Or 74LS86 Quad 2 Input Exclusive Or 74LS107 Dual “JK” Flip-Flop 74128 50 Ohm Line Driver 74LS138 3 to 8 Line Decoder 74LS139 Dual 2 to 4 Line Decoder 74LS151 . 8 Line to 1 Line Data Selector/Multiplexer 74LS153 Dual 4 to 1 Line Multiplexer 74LS157 Quad 2 to 1 Line Multiplexer 74LS158 Quad 2 to 1 Line Multiplexer (inverting) 74LS161 4 Bit Binary Counter 74LS174 Hex “D” Flip-Flop 748189 Ram 16 x 4

74LS245 Octal Buss Transceiver

74LS257 Quad Data Selector/Multiplexer 74LS259 8 Bit Addressable Latch 74LS273 Octal “D” Flip-Flop 74LS283 4 Bit Full Adder 74LS298 Quad 2 Input Multiplexer with Storage 74LS365 Hex Buss Driver 74LS367 Hex Buss Driver 74LS368 Hex Buss Driver (Inverting) 74LS377 Octal “D” Flip-Flop 74LS393 Dual 4 Bit Binary Counter MB7052 Prom 256 X 4 (GG1-1 thru GG1-5) MB2147 Ram 4K X 1 MB8147 Ram 4K X1 UPD2114 Ram 1K X 4 MB8532 Eprom 4K X 8 HN462732 Eprom 4K X 8 Z80A or D780C-1 CPU (must use at location 4M) D780C CPU (may substitute Z80) 4066 Quad Bilateral Switch MB3730 Audio Amplifier LM324 Quad Operational Amplifier O2XX Custom Data Buffer

04XxX Custom Address Buffer

OOXX Custom Address Generator O5XX Custom Video Controller 07XX Custom Horizontal and Vertical Sync. Generators O8XX Custom Buss Transceivers S1XX Custom I/O Ports 5B4XX Custom Sound Generator TMM2016 RAm 2K X8& O6XX Custom Master Buss Controller 18.432 X-tal

7-14

Page 89

CHIP NUMBER

2801815 2N3391 D998 C2500 TIP 110 A733 2N4403 1N4004 1N914B ADDITIONAL DEVICES

FUNCTION

Transistor Transistor Transistor Transistor Transistor Transistor Transistor Diode Diode NPN NPN NPN NPN NPN PNP PNP