Major Havoc TG-252 1st Printing
Major Havoc (rev 3) (Atari, 1983) · Manual · 14 pages · 8 sections · original scan
e Major Havoc
Troubleshooting Guide
© ATARI
A werner communications Company
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Major Havoc
Troubleshooting Guide
A,
ATARI
© Awerer communications Company
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Table of Contents
Troubleshooting the Alpha Microprocessor-C --Controlied Circuits . Preliminary Procedure .. . Leet teeta Troubleshooting the Alpha Address Lines . Troubleshooting the Alpha Data Lines ......... Troubleshooting the Alpha Program RAM Troubleshooting with Checksums
Troubleshooting the Gamma Microcessor-Controlled Circuits ... Preliminary Procedure wees hiee nee Troubleshooting the Gamma Address Lines * beeen ee Troubleshooting the Gamma Data Lines............ 0 -0....0--000- Troubleshooting the Gamma Program RAM . . Troubleshooting with Checksums Troubleshooting the Option Switch Inputs. . Signature Analysis ........... pad RE eek a EP ee aoe
List of Tables
Table Alpha Address Lines......... Table 2 Alpha DataLines ..... Table3 Alpha ROM Checksums . . Table4 = Alpha ROM Checksum. . Table 5 = Alpha RAM Data Retention Table6 Alpha ROM Checksumss . . Table? |= Gamma Address Lines . Table 8 = Gamma Data Lines .... Table? Gamma ROM Checksums .............. bocce eee Table 10 Option Switch Inputs. ................. Hp eine 2 ee Nwee ee
Cha aa een
mn
BWR OWN
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
MAJOR HAVOC Troubleshooting Guide
Troubleshooting with the CAT Box
Troubleshooting the Alpha Microprocessor-Controlled Circuits
Preliminary Procedure I. Tum off the electrical power to the game.
- Remove the Main PCB assembly from the game.
- Connect an extension harness from the game harness tothe Main PCB edge connectors.
- Connectajumper from pin 12 of IC 3Q tothe PHASE 2A test point.
- Connect a jumper from the WDDIS test point to ground.
- Connect the CaT Box 50-pin cable to the 6502 Interface and the 40 pin cable from the Interface to the Main PCB as described on the label attached to the Interface cover. Remove the 6502B microprocessor from its socket at location 2s.
- Insert the Interface 40-pin IC connector into the empty 6502B microprocessor socket. Make sure the [nterface IC connector pin numbers mate with the same pin numbers on the empty microprocessor socket.
- Apply power to the game and to the CAT Box.
- Set the CAT Box switches as follows: a. TESTER SELF-TEST OFF b. TESTER MODE Rw ll. Press the TESTER RESET pushbutton. eT
Teoubleshooting the Alpha Address Lines
- Perform the Preliminary Procedure under Troubleshooting the Alpha Microprocessor-Controlled Circuits. Connect the Data Probe to the CAT Box. Connect the Data Probe ground clip to a GND test point on the Main PCB.
- Set the CAT Box switches as follows: won
a. BYTES 1 b. PULSE MODE UNLATCHED
c. RAV MODE (OFF)
a. Ww WRITE
- Enter address AAAA with the CAT Box keyboard. . Press the DATA SET pushbutton.
- Enter data AA with the CAT Box keyboard. 8. 9. . Setthe RAW MODE switch to STATIC. Check the IC pins listedin Table | with the Data Probe and verify that the corresponding | or 0 LED on the CAT Box is lit.
- Repeat steps 4c through 9 using address 5555 in step 5 and data 55 in step 7.
Table 1 Alpha Address Lines
Address Logic State for IC-Pin Logic State for Address AAAA Address AAAA
| Ala | 1 | 413 | 0 |
| Ala | 0 | 4L2 | 1 |
| BA3a | 1 | 2P.14 | 0 |
| BAl2a | 0 | 2P-12 | 1 |
| BAlla | 1 | 2P-9 | Q |
| BAIOa | 9 | 2P-7 | 1 |
| BAQa | 1 | 2P-5 | 0 |
| BA8a | 0 | 2P.3 | 1 |
| BA7a | 1 | 2Q.18 | 0 |
| BAGa | 0 | 29-16 | 1 |
| BASa | 1 | 2944 | 0 |
| BAda | 0 | 2Q-12 | 1 |
| BA3a | 1 | 29.9 | 0) |
| BAZa | 0 | 2Q7 | 1 |
| Bala | 1 | 29-5 | 0 |
| BAOa | 0 | 293 | 1 |
Troubleshooting the Alpha Data Lines L
wi
or
9. Perform the Preliminary Procedure under Troubleshooting the Alpha Microprocessor-Controlled Circuits. Connect the Data Probe to the CAT Box. Connect the Data Probe ground clip to a GND test point on the Main PCB. Set the CAT Box switches as follows: a. BYTES 1 b. RAW MODE (OFF) c RW WRITE Enter address 0000 with the CAT Box keyboard. Press the DATA SET pushbutton. Enter daca AA with the CAT Box keyboard. Set the RAW MODE switch to PULSE and then to STATIC. Check the IC pin listed in Table 2 with the Data Probe and verify that the } or 0 LED on the CAT Box is lit.
- Repeat steps 4b through 9 using data 55 in step 7.
Troubleshooting Guide
Table 2 Alpha Data Lines
Data Line Logic State for IC-Pin Logic State for Data AA Datz55
| D7a | 1 | 3R-18 | oO |
| D6a | 0 | 3R-17 | 1 |
| DSa@ | 1 | 3R16 | 0 |
| D4a | O | 3R-15 | 1 |
| D3a | 1 | 3R-14 | te) |
| D2a | 0 | 3R-13 | 1 |
| Dia | 1 | 3R-12 | 0 |
| Dow | 0 | 3R-L | 1 |
Troubleshooting the Alpha Program RAM
- Perform the Preliminary Procedure under Troubleshooting the Alpha Microprocessor-Controlled Circuits. Set the CAT Box switches as follows: nv a, DBUS SOURCE ADDR b. BYTES 1024 c. RAV MODE (OFF) d. RAW WRITE Enter address 0000 with the CAT Box keyboard. Set the R/W MODE switch to PULSE and ‘ack to (OFF).
- Set the RAW switch to READ. Set the R/W MODE switch to PULSE and back to (OFF).
- The Program RAM isa 2K x 8 device. To test the entire device perform steps 2c through 6 with the address in step 3 at 0400.
- Ifthe CAT Box reads an address that does not match that entered in step 3, the COMPARE ERROR LED will light.
Troubleshooting with Checksums
- Perform the Preliminary Procedure under Troubleshooting the Alpha Microprocessor-Controlled Circuits.
- Set the CAT Box switches as follows: a. BYTES 1024 . DBUS SOURCE DATA c. RAW MODE (OFF) d. RAW READ e. Checksum Switch on MAJOR HAVOC
- Enter the address given in Table 3 with the CAT Box keyboard.
- Setthe R/W MODE switch to PULSE and then back to (OFF).
- Check the CAT Box ADDRESS/SIGNATURE readout for the appropriate checksum listed in Table 3.
- Repeat steps 3 through 5 for each address listed in Table 3
Table 3 Alpha ROM Checksums
ROM Location Address Checksum Tested
| 136025-103 | IM/N | 8000 | 2950! |
| IM/N | A000 | F36B/ | |
| 136025-104 | IL | co00 | 6637! |
| IL | £000 | 3043! | |
| 136025-101 | 1Q | 2000 | 339? |
| 1Q | 2000 | C093 | |
| 136025-109 | IN/P | 2000 | D559* |
| IN/P | 2000 | 9EIBS |
‘If this checksum is unstable or does not verify, connect one 220-ohm resistor from pin 2. and one from pin 3 of integrated circuit 4L to +5 volts, Then, connect one 330-obm resistor from each of the same pins to ground. Remove the resistors after the checksum troubleshooting is completed. 4MMUPAGE | must be low: If not, ground the RESET A test pointon the Main PCB. sMMUPAGE O must be bigh. If not, use the CAT Boxio write the following data to address 1740: 01. ‘MMUPAGE 0 must bebigh. If not, use the CAT Box to write the follow ing data to address 1740: 02. SMMUPAGE 0 must be high. [fnot, use the CAT Box to write the following data to address 1740: 03
- Connect a jumper from pin 6 of IC 3F to ground.
- Set CAT Box BYTES switch to 256,
- Check the CAT Box ADDRESS/SIGNATURE readout for the appropriate checksum listed in Table 4.
Table 4 Alpha ROM Checksum
ROM Location Tested Address Checksum
| 136025-110 | 6KI/L | 5000 | 5316 |
- Set the CAT Box BYTES switch to 1. ll. Enter the address given in Table 5 with the CAT Box keyboard.
- Press the DATA SET pushbutton.
- Enter the data given in Table 5 with the CAT Box keyboard,
- Set the RAW MODE switch to PULSE and then to (OFF).
MAJOR HAVOC
15. 16. Set the R/W switch to READ. Enter the address given in Table 5. Set the RAW MODE switch to STATIC and then to . (OFF). Check the CAT Box DATA readout for the same data entered in step 13. . Repeat steps 1] through 18 for each address and data given in Table 5.
Table 5 Alpha RAM Data Retention
Address Dara
4000 25 4001 60 4002 00 4003 £0
. Set the R/W switch to WRITE. . Remove the jumper from pin 6 of IC 3F. . Enter address 1640 with the CAT Box keyboard. . Press the DATA SET pushbutton and enter data FF with the CAT Box keyboard. . Set the R/W MODE switch to PULSE then back to (OFF). . Replace the jumper from pin 6 of IC 3F to ground. Enter address 4001 with the CAT Box keyboard. . Press the DATA SET pushbutton. Enter the appropriate data at address 4001 given in Table 6 with the CAT Box keyboard. Set the R/W MODE switch to PULSE then back to (OFF). . Set the BYTES switch to 1024. . Set the R/W switch to READ. . Enter address 6000 with the CAT Box keyboard. Set the R/W MODE switch to PULSE then back to (OFF).
- Check the CAT Box ADDRESS/SIGNATURE readout for the appropriate checksums given in Table 6. . Set the BYTES switch to | and repeat step 20 through 34 to verify the checksums given in Table 6.
Table 6 Alpha ROM Checksums
ROM Tested Location Address Dataat Checksum
4001
| 136025-106 | 6H | 6000 | 60 | FD39 |
| 6H | 6000 | 61 | 3524 | |
| 136025-107 | OK | 6000 | 62 | 8c6D |
| IK | 6000 | 63 | D9C4 |
Troubleshooting Guide
Troubleshooting the Gamma Microprocessor-Controlled Circuits
Preliminary Procedure
Turn off the electrical power to the game. Remove the Main PCB assembly from the game. Connect an extension harness from the game harness to the Main PCB edge connectors.
- Connect the CAT Box 50-pin cable to the 6502 Interface and the 40-pin cable from the Interface to the Main PCB as described on the label attached to the Interface cover. Remove the 65024 microprocessor from its socket at location 8P.
- Insert the Interface 40-pin IC connector into the empty 6502A microprocessor socket. Make sure the Interface IC connector pin numbers mate with the same pin numbers on the empty microprocessor socket. Connect ajumper from the PHASE 2 test point to the 1.25M test point on the Main PCB.
- Apply power to the game and to the CAT Box.
- Set the CAT Box switches as follows: a. TESTER SELF-TEST OFF b. TESTER MODE R/W
- Press the TESTER RESET pushbutton. wre
we
M
Troubleshooting the Gamma Address Lines
- Perform the Preliminary Procedure under Troubleshooting the Gamma Microprocessor-Controlled Circuits. Connect the Data Probe to the CAT Box. Connect the Data Probe ground clip to a GND test point on the Main PCB.
- Set the CAT Box switches as follows: a. BYTES 1 b. PULSE MODE UNLATCHED c RAW MODE (OFF) a. RAW WRITE Enter address AAAA with the CAT Box keyboard. Press the DATA SET pushbutton. Enter data AA with the CAT Box keyboard. Set the R/W MODE switch to STATIC. Check the IC pins listed in Table 7 with the Data Probe and verify that the corresponding | or 0 LED on the CAT Box is lit.
- Repeat steps 4c through 9 using address 5555 in step 5 and data 55 in step 7. wir
Ow ~ @
Troubleshooting Guide
Table 7 Gamma Address Lines
‘Address Logic State for IC-Pin Logic State for Address AAAA Address 5555
| AlSy | I | 8R-15 | 0 |
| Al4y | 0 | 8R13 | 1 |
| Alby | 1 | 8R-14 | 0 |
| Al2y | 0 | 982 | 1 |
| Ally | i | 98-23 | 0 |
| Al0y | 0) | 98-21 | 1 |
| Ady | 1 | 98-24 | oO |
| A8Y | 0 | 98-25 | 1 |
| ATy | 1 | 98-3, | i) |
| AGy | 0 | 98-4 | 1 |
| ASY | 1 | 98-5 | 0 |
| Ady | 0 | 98-6 | 1 |
| ABy | 1 | 98-7 | ) |
| Aly | 0 | 98-8 | 1 |
| Aly | 1 | 98-9 | 0 |
| AOy | 0 | 95-10 | 1 |
Troubleshooting the Gamma Data Lines L Perform the Preliminary Procedure under Troubleshooting the Gamma Microprocessor-Controlled Circuits.
- Connect the Data Probe to the CAT Box.
- Connect the Data Probe ground clip to a GND test point on the Main PCB.
- Ser the CAT Box switches as follows:
a. BYTES 1 b. RW (OFF) c RW WRITE
- Enter address 0000 with the CAT Box keyboard.
- Press the DATA SET pushbutton. 7 Enter data AA with the CAT Box keyboard.
- Set the R/W MODE switch to PULSE and then to STATIC.
- Check the IC pin listed in Table 8 with the Data Probe and verify that the | or 0 LED on the CAT Box is lit.
Table 8 Gamma Data Lines
Data Line Logic State for IC-Pin Logic State for Data AA Data 55
| DTy | 1 | 129-18 | 0 |
| D6y | 0 | 12Q-17 | 1 |
| DSy | 1 | 120-16 | 0 |
| D4y | 0 | 129-15 | 1 |
| D3y | t | 12Q-14 | 0 |
| D2y | ° | 12913, | 1 |
| Diy | 1 | 129-12 | 0 |
| DOY | 0 | 12Q-1 | 1 |
MAJOR HAVOC
Troubleshooting the Gamma Program RAM
Perform the Preliminary Procedure under Troubleshooting the Gamma Microprocessor-Controlled Circuits. Set the CAT Box switches as follows:
a. DBUS SOURCE ADDR b. BYTES 1024 c. RAV MODE (OFF) d. RW WRITE
Enter address 0000 with the CAT Box keyboard. Set the R/W MODE switch to PULSE and back to (OFF). Set the R/W switch to READ. Set the R/W MODE switch to PULSE and back to (OFF). The Program RAM isa2K x 8device. To test the entire device perform steps 3 through 6 with the address in step 3 at 0400. If the CAT Box reads an address that does not match that entered in step 3, the COMPARE ERROR LED will light.
Troubleshooting with Checksums
w
we
Perform the Preliminary Procedure under Troubieshooting the Gamma Microprocessor- Controlled Circuits.
Set the CAT Box switches as follows:
a. BYTES 1024 b. DBUS SOURCE DATA c. RW(not) MODE (OFF) d. R/W(not) READ e. Checksum Switch on Enter the address given in Table 9. Set the R/W MODE switch to PULSE and then back to (OFF). Check the CAT Box ADDRESS/SIGNATURE readout for the appropriate checksum listed in Table 9. Repeat steps 3 through 5 for each address listed in Table 9.
MAJOR HAVOC
Table 9 Gamma ROM Checksums
ROM Location Address Checksum Tested
136025-108 9S 8000 1FE3 9S A000 CO3F
Troubleshooting the Option Switch Inputs
- Perform the Preliminary Procedure under Troubleshooting the Gamma Microprocessor-Controlled Circuits.
- Set the CAT Box switches as follows:
a. BYTES 1 b. RW READ c. RAW MODE (OFF)
- Enter the address listed in Table 10 with the CAT Box keyboard. +4. Set the R/W MODE switch to STATIC.
- Activate the input switch listed in Table 10. Check the CAT Box DATA readout for the appropriate test result specified in Table 10. Troubleshooting Guide
7 Repeat steps 2c through 6 for each address given in Table 10.
Table 10 Option Switch Inputs
Address Input Switches Test Results
| 2800 | FIRE/SHIELD | DATA readout changes when |
either of these switches is activated.
| 3800 | Roller Control | DATA readout changes when |
roller control is spun ineither direction.
| 4000 | Option switch at | DATA readout changes when |
location 8S any of these switches are activated.
If the preceding procedures for troubleshooting the alpha and gamma microprocessor-controlled circuits are successful, then there should be enough of the game circuitry working to perform the Self-Test procedures.
Signature Analysis The software necessary to perform signature analysis is not available in this game.
a
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.