CATHODE RAY TOMES

Spiderman

Spider-Man (JAKKS Pacific TV Game, Game-Key Ready) (JAKKS Pacific Inc / Digital Eclipse, 2004) · Manual · 26 pages · 9 sections · original scan

Page 1

4 Player Upright

Owner's Installation and Operating Manual SEGA ENTERPRISES, INC. U.S.A

SEGA ENTERPRISES, INC. U.S.A. 999-0114

Page 2

BY:

SEGA Enterprises, Inc. (U.S.A.)

2149 Paragon Drive San Jose, California 95131 Phone Number. ~ (408) 435-0201 FAX Number (408) 435-0294

SPECIFICATIONS

HEIGHT: 70.5 in. WIDTH: 36.5 in. (with Control Panel) WIDTH 25.5 in. (w/o Control Panel) DEPTH: 38.5 in. NET WEIGHT: 275 Ibs. POWER 360 warts VOLTAGE 120 volts AC CURRENT 3 Amps

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense.
Page 3

Table of Contents

SPECIFICATIONS INTRODUCTION OF THE OWNER’S MANUAL..

ORIGINAL SEAL . COPYRIGHT NOTICE... on PRECAUTIONS CONCERNING THE PLA F.C.C. REQUIREMENTS SERVICE SWITCHES... SYSTEM 32 BOARD TEST MODE... SELECTION OF TEST ITEMS. MEMORY TEST........:0s000008 WCoOMMOIUAAAUUUAALN SOUND TEST.. RGB COLOR CHECK: C.R.T. TEST GAME ASSIGNMENTS .. COIN ASSIGNMENTS... MANUAL SETTING... COIN/CREDIT SETTING. MANUAL SETTINGS..

WIRING DIAGRAM..

NOTE: DESCRIPTIONS HEREIN CONTAINED MAY BE SUBJECT TO IMPROVEMENT OR CHANGES WITHOUT NOTICE.
Page 4

INTRODUCTION OF THE OWNER’S MANUAL

SEGA ENTERPRISES, LTD., supported by its high electronic technology of LSIs, microprocessors, etc, and a wealth of experience, has for more than 30 years been supplying various innovative and popular game machines to the world market. This OWNER’S manual is intended to provide detailed comments together with all the necessary information covering the operation in general of electronic assemblies, electromechanical servicing control, spare parts, etc. This manual is intended for those who have knowledge of electricity and technical expertise especially in ICs, CRTs, microprocessors, etc. Carefully read so as to acquire sufficient knowledge before working on the machine. ~ Should there be a malfunction, non-technical personnel should under no circumstances touch the interior system.

HANDLING PRECAUTIONS

When installing or inspecting, be very careful of the following points and pay attention to ensure that the player can enjoy the game safely.

© Be sure to turn the power off before working on the machine, © To insert or pull out the plug quickly is dangerous. 0 Itis necessary to make sure that the power cord or the grounding wire is not exposed on the road, etc, in a manner so as to be dangerous. Make sure that grounding connections are made safely at the position where specified. Do not use any fuse that does not meet the specified rating. Make complete connections for the IC board and other connectors. Insufficient insertion is very dangerous. oo

Also, for the IC board circuit inspections, only the logic probe is allowed. The use of a tester is not permitted, so be careful in this regard. After confirming that there are no irregularities, turn the power ON.

Page 5

PREVENTION OF COUNTERFEITING AND CONVERSION

LABELLING To prevent counterfeits and conversions, the following labels are put on all the SEGA products. When handling such goods, be sure to confirm the labels. They are used to prevent illegal acts such as the unauthorized copying of the products and the printed circuit boards thereof or carrying on business by manufacturing similar merchandise or ty converting, selling or using such products or printed circuit boards.

The following seal is put on the machines manufactured by SEGA

ee ensennene

AYST VE were eer ere ee

ADTEnRA LID me i ct a ice ea oe te

ewer eeroe

ORIGINAL SEAL

COPYRIGHT NOTICE This SEGA product has the copyright notice as follows:

© SEGA 1991

This signifies that this work was disclosed in 1991 and is the property of SEGA ENTERPRISES, LTD.

Page 6

PRECAUTIONS CONCERNING THE PLACE OF INSTALLATION

This is an indoor game machine, Absolutely do not install it outside. Even indoors, avoid installing in places mentioned below so as to ensure proper usage:

Places subject to rain or water leakage, or condensation due to humidity. In the proximity of an indoor swimming pool and/or shower. Places subject to direct sunlight. : Places subject to heat sources from heating units, etc., or hot air. Vicinity of highly flammable/volatile chemicals or hazardous matter. Sloped surfaces. Vicinity of anti-disaster facilities such us fire exits and fire extinguishers. Places subject to any type of violent impact, Dusty places. Residential Environment - (See F.C.C. statement below) oo oo 00 0000

F.C.C. REQUIREMENTS

The Federal Communications Commission requires that-all Class A equipment be verified and labeled as follows:

This equipment complies with the requirements in part 15 of FCC Rules for a Class A computing device. Operation of this equipment in a residential area may cause unacceptable interference to radio and TV reception requiring the operator to take what ever steps are necessary to correct the interference.

i 2 a atacned in 2 onspicr 9 or. al 2. x cal

C ves £1934 (ACD ied :

Page 7

SERVICE SWITCHES

When you open the Coin Chute Door, you will notice three switches. From left to right, the first is the Volume Control, second is the Service Switch and the third is the Test Switch. (These switches are also referred to as buttons when explaining the Test Mode functions.)

Volume Control Pot: Controls the volume of the speakers. Service Switch: Allows you to receive game credits to test the function of the game while maintaining the integrity of the Coin Credit meter. This is used when servicing the game. Test Switch: Used in the Test Mode functions,

SYSTEM 32 BOARD:

SYSTEM 32

BARE BD NO. 171-5965-01A

i

MAIN BD

BARE BD NO. 171-5964E 471-5964F & vari 1

837-7968 VO BD

CN2: JST 10P o CN3: JST 11P cN3 CN4: JST O5P a CN: CN4 CN5: JST O6P a

Page 8

The four player game has a white start button for each player, one red button to control the attack feature, one yellow button to control the jump feature and an eight way joystick.

JOYSTICK CONTROL DIRECTIONS

TEST MODE

The test operation of this game allows you to verify operation of the game memory, input, sound, CRT, and game assignments. The test mode also includes coin assignments, and bookkeeping functions.

Selection of Test Items:

  • Push the TEST SW to cause the following TEST ITEM MENU to appear:

TEST MODE INDIVIDUAL

MEMORY TEST

INPUT TEST

SOUND TEST CRT. TEST GAME ASSIGNMENTS COIN ASSIGNMENTS BOOKEEPING BACKUP DATA CLEAR ~ EXIT

SELECT BY SERVICE BUTTON PUSH TEST BUTTON

  • When you push the service switch, the arrow (>) will move to the next item on the menu.
  • Press the Test Button to perform the selected function.
Page 9

Memory Test. When this item is selected, a list of Integrated Circuits will appear. Each item will display “Good” or “Bad” to indicate whether or not the Ici is functioning properly. If “Bad” appears, it indicates a malfunctioning IC.

MEMORY TEST

FO IC6 GOOD IC7 GOOD IC13 GOOD 1C14 GOOD Ic16 GOOD 1C¢37 GOOD 1C62 GOOD IC63 GOOD IC64 GOOD IC65 GOOD IC66 GOOD IC68 GOOD IC69 GOOD 1C70 GOOD 1C71 GOOD 1¢74 GOOD IC75 GOOD

PUSH TEST BUTTON TO EXIT

Input Test. This test indicates the condition of each switch and potentiometer. To test a switch, operate it, When the switch is in good operating condition, the “Off” will change to “On”. If it does not change, it indicates a malfunctioning switch.

INPUT TEST

% )

PLAYER1P2P

iP Of Of

DOWOffOff
RIGHTOffOff
LEFTOffOff

ATTACK Off Off

JUMPOffOff
STARTOfOff
CONOfOff

RQQVQQQQQ SQQVeggg

SERVICE-Off TEST-Off

PUSH TEST BUTTON TO EXIT

Page 10

Sound Test. The sound test indicates whether or not the sound in each category is working properly or not. Select the item using the Service Button and then push the Test Button.

MUSIC 0 (Music 1-16) EFFECT 0 (Effect 1-97) VOKE 0 (Voice 1-34) = EXT

SELECT BY SERVICE BUTTON PUSH TEST BUTTON

RGB Color Check. The CRT test allows you to adjust the color of the monitor. The color becomes brighter from left to right

C.R.T. TEST 12

PUSH TEST BUTTON TO CONTINUE

Page 11

C.R.T. Test. View the image and make sure that all corners are straight. If the corners are not straight, make the necessary adjustments.

Game Assignments.

The monitor allows you to adjust game assignments as follows:

GAME ASSIGNMENTS, GAME DIFFICULTY = “ INITIAL VITALITY MIN } (B)

ADVERTISE SOUND (C) MONITOR FLIP () CABINET TYPE (E) START BUTTON ) ~ EXT SELECT BY SERVICE BUTTON PUSH TEST BUTTON

A. Game Difficulty: Values range from 1 to 8. The higher the number, the more difficult the game play. Default serting is 5.

B. Vitality: Values range from 200 to 600. The default setting is 400.

Page 12

Advertise Sound: Allows you to turn the advertising sound on or off. Default is Off.

Monitor Flip: Should be set to normal.

Cabinet Type: Should be set to 4P.

Start Button: ‘Should be set to Use.

Coin. Assignments. The coin chute type is set to individual. The credit to start play is two credits. One coin per chute equals one credit per chute. Fifteen different types of coin credits can be selected. See the coin/chute setting matrix on page 15.

COIN ASSIGNMENTS:

COIN CHUTE TYPE INDIVIDUAL

CREDITTO START 2 CREDITS

COIN/CREDIT SETTING #1 COIN CHUTE #1 1 COIN 1 CREDIT COIN CHUTE #2 1 COIN 1 CREDIT

MANUAL SETTING > EXIT

SELECT BY SERVICE BUTTON AND PUSH TEST BUTTON

Page 13

Manual Setting. The coin to credit, Bonus Adder information and coin chute multiplier are displayed. Select the item by using the Service Button and then push the Test Button to perform the selected function,

COIN ASSIGNMENTS MANUAL SETTING

COIN TO CREDIT 1 COIN 1CREDIT BONUS ADDER NO BONUS ADDER

COIN CHUTE MULTIPLIER

1 COIN COUNTS AS 1 COIN

78 9

SELECT BY SERVICE BUTTON AND PUSH TEST BUTTON

Page 14

COIN/CREDIT SETTING (COIN CHUTE INDIVIDUAL TYPE)

ISETTING #12 | 2COINS|1 CREDIT _| 2 COINS |3 CREDITS

SETTING #18 | 4 COINS | 1 CREDIT SETTING #19 2 COINS | 2 CREDITS 3 COINS | 3 CREDITS 4 COINS | 5 CREDITS 5 COINS |2 CREDITS SETTING #22 | 2COINS | 1 CREDIT 4 COINS | 2 CREDITS 5 COINS |3 CREDITS SETTING #24 2 COINS | 2 CREDITS 3 COINS | 3 CREDITS 4 COINS | 4 CREDITS -5 COINS |6 CREDITS SETTING #26 FREE PLAY

Page 15

MANUAL SETTINGS

COIN TO CREDIT | 2 COINS |1 CREDIT | [3 COINS [1 CREDIT | [4 COINS [7 CREDIT | | 5COINS [1 CREDIT | [ 6 COINS [1 CREOMT |

[9 COINS [1 CREDIT |

'3 COINS GIVE 1 EXTRA COIN 4 COINS GIVE 1 EXTRA COIN

7 COINS GIVE 1 EXTRA COIN 8 COINS GIVE 1 EXTRA COIN 9 COINS GIVE 1 EXTRA COIN

BONUS ADDER

1 COIN COUNTS AS 1 COIN 1 COIN COUNTS AS 2 COIN:

  • COIN COUNTS AS 4 COINS 1 COIN COUNTS AS 5 COIN:

1 COIN COUNTS AS 7 COIN: 1 COIN COUNTS AS 8 COINS 1 COIN COUNTS AS 9 COIN:

  • COIN COUNTS AS 1 COIN 1 COIN COUNTS AS 2 COINS 1 COIN COUNTS AS 3 COIN: 1.COIN COUNTS AS 4 COIN: 1 COIN COUNTS AS 5 COIN: 1 COIN COUNTS AS 6 COINS 1 COIN COUNTS AS 7 COINS 1_COIN COUNTS AS 8 COIN: 1 COIN COUNTS AS 9 COIN:

Coin chute #3 and coin chute #4 multipliers are the same as for #1 and #2 above.

Page 16

Bookkeeping 1/2. The Coin Chutes #1 through #4 are displayed with the total number of coin drops recorded per chute. The total of all four chutes is recorded under Total Coin. Coin Credits are displayed and the number of times the service switch has been used to gain credits is also recorded. The total of both types of credits are recorded under Total Credit.

Number of Games: displays the number of times the game has been played. Total Operating time is displayed in days, hours, minutes and seconds. The total game playing time is displayed in a like fashion. Average game length , Longest game time, and Shortest game time are displayed in hours, minutes and seconds, The utilization factor is displayed as a percentage. To continue, push the Test Button.

BOOKKEEPING 1/2 COIN CHUTE #1 COIN CHUTE #2 COIN CHUTE #3 COIN CHUTE #4 TOTAL COINS COIN CREDITS SERVICE CREDITS TOTAL CREDITS

NUMBER OF GAMES TOTAL OP. TIME Od Oh OmOs TOTAL GAME TIME 0d Oh Om Os AVERAGE GAME TIME Oh Om 0s LONGEST GAME TIME Oh Om OsOm Os SHORTEST GAME TIME Oh UTILIZATION FACTOR 0.0%

PUSH TEST BUTTON TO CONTINUE

Page 17

Scoring information is displayed below. The average score, highest score, and the lowest score ranges are also displayed. To exit, push the Test Button.

BOOKKEEPING 22 Time Histogram Om00s~Om29s Om30s~Om59s 1m00s~1m29s 1m30s~im59s 2m00s~2m29s 2m30s-2m59s 3m00s~3m29s 3m30s-3m59s 4m00s~4m29s 4m30s~4m59s 5m00s~9mS9s OVER 10m00s 0 eoe00000000

° PUSH TEST BUTTON TO EXIT

If you wish to delete all backup bookkeeping data, simply select YES and push the Test Button. Otherwise, select No and push the Service Button.

BACKUP DATA CLEAR

SELECT SY SERVICE BUTTON AND PUSH TEST BUTTON

Page 18

The following is a diagram of the Spider-Man Printed Circuit Board Assy #833-8331-04,

ROM BD No. 834-8332-01

MAIN BD No. 837-7428-01

Page 19

SPIDER-MAN FILTER BOARD 839-0207

JSTSP = UST4P UST 16P

1e) FILTER BOARD:

Page 20

The following matrix displays the location of each IC, its primary function.

SPIDER-MAN

Page 21

Monitor Adjustments

GREEN DAIVE mMORIZ SIZE GREEN BLU CUT OFF CUT OFF

RED ORIVE RED. WORIZ RASTER POSITION

VERT RASTER POS VERT SIZE VERT HOLD BRIGHTNESS

BLUE DRIVE CUT OFF GRN ORIVE GREEN HORTZ CUT OFF SIZE HWORIZ RASTER POSITION

WORIZ VIDEO: SHIFT WORTZ HOLD. VERT RASTER POS VERT SIZE VERT HOLD BRIGHTNESS

Page 22

In Case of Difficulty No Raster/No Video ~Check AC. line cord Check line fuse ~Check monitor brightness Check power switch and/or interlock switch Check all solder connections on line filter and transformer Check for proper orientation of the 56 pin PCB connector Raster/No Video ~Check all PCB to monitor connections Check power supply voltage on PCB No Video/Game sounds can be beard -Check monitor brightness Check all PCB to monitor connections Incorrect Colors -Monitor needs degaussing ~Check for proper wiring between PCB and monitor Check monitor adjustment and adjust if necessary Wavy Picture Check monitor ground is properly connected to monitor -Be certain sync inputs are properly connected to monitor Check horizontal hold adjusunent Vertical Roll/Horizontal Tear Check horizontal and/or vertical hold adjustments -Check for proper wiring of syne from PCB to monitor No Sound Check volume control potentiometer adjustment Check for + 12 volis on edge connector of PCB -Check wiring from PCB to speaker ~Check speaker for low resistance between the "+" and"- "tabs Bad Sound : Check wiring to speaker for bad solder connections Check sound with another speaker No Switch Input ~Check ground connection to switches ~Check wiring berween PCB and switches for proper connection -Check switches with an-ohm meter to verify proper operation Switch Operates Incorrect Function Check wiring between PCB and switches for proper orientation ~Check wiring for shorts between switch inputs No Coin Meter ~Check wiring to coin meter -Check that + 5 volts is on + side of meter Verify a + 5 volt meter is used When coin switch is made and meter pulses, the screen blanks out and/or game resets -Verify that a meter with a diode is used -If no diode is built in meter a IN4004 can be used across the meter, Cathode to "+" side of meter and anode 10 "-"side of meter.

Page 23

Final Assembly, SPIDER-MAN # 999-0101

Front: Marquee Header (999-0096) Rear: Fluorescent Lamp Assy (F15T8)

Side Decal Speakers (999-0116) (Left ) (999-0098) Monitor Card with Instructions beet Monitor Bezel (999-0100) (999-0099) PLAYER 2 Original Seal (421-5800-161) PLAYER 4

Assy Control Panel (999-0104)

  • Control Panel Overlay (999-0095) + Player Controls 4 Joysticks (999-0062) 4 Start Buttons (999-0063) 4 Attack Buttons (999-0064) 4 Jump Bunons (999-0115)

Coin Door Assembly 4 Envy-Individual (999-0108)

Page 24

Part Number

999-0101 999-0102 25"Wells ST 999-0100 999-0116 999-0103 999-0104 999-0095 999-0096 999-0097 999-0099 999-0098 999-0062 999-0064 999-0063 999-0115 999-0105 999-0106 999-0107 999-0108 FISTS 999-0109 999-0110 999-0111 999-0112 600-5849-03 600-5891-10 833-8331-04 839-0207 999-0113 999-0114 PARTS LIST

Description

Fina] Assy Cabinet Power Supply, Switching XT-150 Monitor, 25” Standard Resolution Bezel, Plastic Speaker 8 Ohm 15W (5x7) Assy, Trucking Wheel Assy, Control Panel Assy, Control Panel Overlay Marquee Header, Spider-Man U/R Monitor Card, w/ Play Instr. Side Decal (Right) Side Decal (Left) Joystick, 8-way Pushbutton, Red Pushbutton, White Pushbutton, Yellow Clamp, Control Panel Strike, Control Panel Assy, Control Panel Harness Assy, Coin Door 4 Entry Assy, Fluorescent Lamp (18” F15T/80W) Transformer, Isolation Fuse 1A Slow Blo Fuseholder, 1P Assy, Main Harness Wire Harness, JAMMA (Logic to Filter) Wire Harness, /O (Logic to Filter) Assy, Spider-Man PCB Assy Filter PCB Monitor Glass (22-3/4 x 23-15/16 x 3/16) Owner’s Manual, Spider-Man U/R Pe NN REPRE Ee ENN Eee EI

Page 25

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 26

INDEX

Advertise Sound 12 total game playing time 16 Average game length 16 Total Operating time 16 backup bookkeeping data 17 utilization factor 16 Bonus Adder 13 Vitality 11 Bookkeeping 1/2 16 Volume Control Pot 7 CRT. Test 11 Wiring Diagram 26 Cabinet Type 12 Virality13 0 * Coin Assignments 12 Volume Control Pot 7 coin chute multiplier 13 coin to credit, 13 COIN/CREDIT SETTING 14 FILTER BOARD 19 Game Assignments 11 Game Difficulty 11 In Case of Difficulty 22 individual 12 Input Test 9 Integrated Circuits 9 Longest game ume 16 Manual Setting. 13 MANUAL SETTINGS 15 Memory Test. 9 Monitor Adjustments 21 Monitor Flip 12 Number of Games 16 PARTS LIST 24 RGB Color Check 10 Scoring information 17 Service Switch 7 SERVICE SWITCHES 7 Shortest game time 16 Sound Test. 10 SPECIFICATIONS 2 Spider-Man Printed Circuit Board Assy 18 Start Bunton 12 Test Button 8 TEST ITEM MENU 8 TEST MODE 8 Test Switch 7