CATHODE RAY TOMES

Burgertime Parts and Operating Manual (Nov 1982)

Burger Time (Bandai) (Bandai, 1983) · Parts & Operating Manual · 84 pages · 42 sections · original scan

Page 1

November, 1982 Game Nos. 333 & 334

NO. 334 COCKTAIL

NO. 333 UPRIGHT

MIDWAY MFG. CO.

10750 W. Grand Avenue Franklin Park, Illinois 60131 U.S.A.

Phone: (312) 451-1360 Cable Address: MIDCO Telex No.: 72-1596

Form No. 0333-00300-0000

Page 2
WARNING THIS GAME MUST BE GROUNDED. FAILURE TO DO SO MAY RESULT IN DESTRUCTION TO ELECTRONIC COMPONENTS.
WARNING: This equipment generates. uses. and can radiate radio trequency energy and if not and used in accordance with the instructions manual. may cause interference to radio communications. It has been tested and found to comply with the limits for a CLASS A computing device pursuant to SUBPART J of PART 15 of FCC RULES. which are designed to provide reasonable protection against such interference when operated ina commerical environment. Operation of this equipment in a residential area ts likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference

ELECTRICAL BULLETIN: FOR ALL APPARATUS COVERED BY THE CANADIAN STANDARDS ASSOCIATION (CSA) STANDARD C22.2 NO. 1, WHICH EMPLOYS A SUPPLY CORD TERMINATED WITH A POLARIZED 2-PRONG ATTACHMENT PLUG.

CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET

UNLESS bee BLADES CAN BE FULLY INSERTED TO PREVENT BLADE

EXPOSURE.

ATTENTION: POUR PREVENIR CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR. UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT.

CBillly|MIDWAY

OUR TOLL FREE NUMBERS FOR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER BALLY/MIDWAY™ GAME YOU NOW HAVE ON LOCATION.

CALL US FOR PROMPT, COURTEOUS ANSWERS TO YOUR PROBLEMS

ANSWERS TO YOUR PROBLEMS.

Continental U.S. 800-323-7182 Illinois Only 1-800-942-0497

= COPYRIGHT MCMLXXXIII BY BALLY/MIDWAY CO. ALL RIGHTS RESERVED.

NO PART OF THIS PUBLICATION MAY BE REPRODUCED BY ANY MECHANICAL, PHOTOGRAPHIC, OR ELECTRONIC PROCESS, OR IN THE FORM OF A PHONOGRAPHIC RECORDING, NOR MAY IT BE TRANSMITTED, OR OTHERWISE COPIED FOR PUBLIC OR PRIVATE USE, WITHOUT PERMISSION FROM THE PUBLISHER. THIS MANUAL IS FOR SERVICE USE ONLY, AND NOT FOR GENERAL DISTRIBUTION. FOR PERMISSION REQUESTS, WRITE: MIDWAY MFG. CO., 10750 W. GRAND AVE., FRANKLIN PARK, IL 60131 Printed in U.S.A.

Page 3

DESCRIPTION TABLE OF CONTENTS

Introduction .......... 6. cece cece eee enn een n eee e nee e ete rete etn enn n es 1-1

Location and Setup Inspection ... Installation Self-Test ..... Game Volume Adjustment Control Option Switch Settings

Game Operation Self-Test Mode Attract Mode.... Ready to Play Mode. Play Mode.......... High Score/Initial Mode . Two Player Operation ........ 6.6 e cece eee eee cere ee eee ee een nee e eet e ene e een nee 3-'

Maintenance and Repair Cleaning . Fuse Replace! Opening the Control Panel .. Removal of the Main Display Glass & TV. Bezel TV. Monitor Replacement.......... Printed Circuit Board Replacemen Opening the Attraction Panel

Illustrated Parts Breakdown No. 333 — Burger Time — Upright — Front .. No. 333 — Burger Time — Upright — Front arts . No. 333 — Burger Time — Upright — Rear Access....... No. 333 — Burger Time — Upright — Rear Access — Parts List . No. 334 — Burger Time — Cocktail — Front............. No. 334 — Burger Time — Cocktail — Front — Parts List No. 334 — Burger Time — Cocktail — Interior Access ... No. 334 — Burger Time — Cocktail — Interior Access — Parts List Burger Time — Control Assembly — All Versions — Parts List... Burger Time — Control Assembly — All Versions............... Burger Time — Power Chassis Assembly — 70VA, 115V. — All Versions... Burger Time — Power Chassis Assembly — 70VA, 115V. — All Versions Front Door Assembly — U.S.A. 25¢ ............008 Front Door Assembly — U.S.A. 25¢ — Parts List... No. 333 — Burger Time — Upright — Header Fluorescent Assy. No. 333 — Burger Time — Upright — Header Fluorescent Assy. — Parts List..

Page 4

TABLE OF CONTENTS (cont'd)

DESCRIPTION PAGE

Vi.

Vil.

Vill. Technical Troubleshooting ................ 00. c ccc cee cece cent e nen e cent tent ennes 6-1 Introduction General Suggestions .. Harness Component Troubleshooting . Transformer and Line Voltage Problems ... A Glossary of Microprocessor Terms .. Introduction to the Z80 CPU...... General Purpose Registers ... Arithmetic and Logic Unit (ALU) .. Instruction Register and CPU Control Z80 CPU Pin Description .

Coin Door Maintenance Metal Coin Acceptor Merchanisms Plastic Coin Acceptor Mechanisms. .

TV. Monitor Manual Introduction ... Symptom Diagnosis Guide to Schematic Symbols Troubleshooting...... Theory of Operation. . Differences Between Monitors . Controls You May Not Touch Parts Interchangeability ..... Wells Gardner Monitor Schematic — 19” Wells Gardner Monitor Replacement Parts List . Electrohome Monitor Schematic — 19"....... Electrohome Monitor Replacement Parts List . Electrohome Monitor Schematic — 13”...... Electrohome Monitor Replacement Parts List ... i

een i An GOnanon+ wr mroerrreoe orw=o @ we

8-19

Schematics and Wiring Diagrams Wiring Diagram — Upright & Cocktail . Sound !/O Board — Component Layout . Sound I/O Board — Schematic ..... CPU Board — Component Layout . CPU Board — Schematic........... 70VA Power Supply Board — Component Layout . 70VA Power Supply Board — Schematic .... 70VA Power Chassis — Upright — Schematic 70VA Power Chassis — Cocktail — Schematic . . SeooDo0nvo OMNODHASWON—

Page 5

FIGURE

nob OhkOMU KODA

vN=A0 VPP PHEHHHLHHPHPHSHSS PV YYT ahwn— NNN NE TABLE OF FIGURES

Assigned Point Values 21-2 Location of Serial No., Interlock Switch, On/Off Switch, & Major Sub-Assemblies . 2-2 Interlock Switch Operation .......... 06sec ese cece eee eee eee 2-3 Game Volume Adjustment Control! & Option Switch Location 2-4 Option Switch Settings . 2-5 Location of Fuses ...... 4-1 Opening the Control Panel — Upright 4-2 Removing the Control Panel — Cocktail 4-2 Opening the Control Panel — Upright... 4-3 Removal of Main Display Glass & TV. Be: 4-3 Removing Top Glass — Cocktail 4-4 Removing Monitor — Upright . 4-4 Opening the Cocktail Game . - Removing Monitor — Cocktail .. Replacing P.C.B.s — Upright & Cocktai Opening the Attraction Panel — Upright . Replacing Fluorescent Tube Starter — Upright. Removing and Replacing the Coin Acceptor . Cleaning the Metal Coin Acceptor .......... Lubricating the Metal Coin Acceptor . Opening the Plastic Coin Acceptor..... Changing the Plastic Coin Acceptor to Accept American or Canadian Quarters .. BS a m

Page 6

Burger Time

IMPORTANT NOTE

DO NOT plug in your new game yet. Before you do anything to your game, we recommend that you read SECTIONS | and Il of this manual completely. It will not take more than a few minutes and it may be very helpful.

I. Introduction

BURGER TIME is a one or a two player game. There are two models: the “UPRIGHT” and “COCKTAIL TABLE”. When the two player mode is selected on the Upright model, the players take turns at the controls to guide their CHEF through the game course. If you have purchased the Cocktail Table model of this game, the rules of play are the same. The only difference is that in the two player mode of the Cocktail Table game, the picture flips to face you when it’s your turn. When playing this game, you are the CHEF’s controlling force. It is up to you to direct him through the maze of ladders and platforms to build his Burgers. Your job is to give him guidance while building his Burgers and to keep him away from his pursuers. These pursuers are very sneaky and, if given half a chance, will try to corner your CHEF at the end of one of the platforms or to trap him on one of the ladders he has to use to get from one level of platforms to another. The CHEF's pursuers have no defense mechanisms of any kind. But they CANNOT be PERMANENTLY

1-1 eliminated either. As soon as your CHEF puts one pursuer out of commission, another appears somewhere on the screen at the edge of one of the platforms. However, in an emergency, your CHEF can slow these pursuers down for short periods of time. Thisis accomplished by having him throw PEPPER on them. When hit by the PEPPER, his pursuers will be disabled for several seconds. When they are disabled like this, the CHEF can walk right over them and not be caught. As your skill level increases, the number and direction of pursuers coming at your CHEF at any one time and the speed with which they move, is gradually increased; plus, their pursuit patterns become more and more devious while their overall accuracy is highly improved. Bonus CHEF’s are awarded to you periodically throughout the game as you reach or pass certain preselected point values. Each task or event that your CHEF can perform or cause to happen has an assigned point value as listed in Figure 1-1.

Page 7

Major Features

Your BURGER TIME game is equipped with a very detailed self-diagnostic package. It also comes with a new improved Power Chassis designed to help reduce electrical interference with other equipment.

OBJECT DESCRIPTION

. ALL BURGER PARTS . BURGER PART + 1 PURSUER BURGER PART + 2 PURSUERS . BURGER PART + 3 PURSUERS BURGER PART + 4 PURSUERS ICE CREAM CONE . COFFEE CUP . FRENCH FRIES . FLATTENED HOT DOG . FLATTENED PICKLE . FLATTENED EGG 2. 3.

5. 6. 7. 8. 9. 0. as

Game Objective

The object of the game is to HAVE FUN and survive as long as possible while constantly improving your skills and building as many Burgers as you can. As you do this, each following rack of the game will have more pursuers, more difficult mazes, and will in general be harder to complete.

POINT VALUE

50 POINTS PER LEVEL DROPPED 500 POINTS PER DROP 1000 POINTS PER DROP 1500 POINTS PER DROP 2000 POINTS PER DROP 500 POINTS + ONE PEPPER 1000 POINTS + ONE PEPPER 1500 POINTS + ONE PEPPER 100 POINTS 200 POINTS 300 POINTS

Figure 1-1 Assigned Point Values

Page 8

II. Location and Setup

INSPECTION:

  • Remove the game from its shipping crate.
  • Inspect the entire outside of it for any signs of damage. C Any scratches?, dents?, cracks? O Any broken controls? O Any broken glass or plastic? C Just look it over closely and make a note of any signs of damage.
  • Remove the shipping cleats from the bottom of the cabinet. CJ UPRIGHT MODELS ONLY: In order to help prevent easy theft of your game, you may wish to remove the Caster Wheel Assemblies from the bottom of your cabinet at this time.
  • Install the four levelers, one at each corner of the cabinet. © Level the cabinet.
  • Open the cabinet and inspect the inside of the game for any signs of damage. See Figure 2-1. D Also check to make sure all plug-in connectors on the wire harness are firmly seated.
NOTE: ALL connectors or plugs are keyed so they will only go together when all pins are properly lined up.

Ol Replug any connectors found unplugged. DO NOT FORCE PLUGS ONTO CONNECTORS. DO NOT FORCE PLUGS TOGETHER . If it won't go on easily, assuming the keys are lined up, it either does not belong there or is damaged. O Make sure ail printed circuit boards (P.C.B.’s) are firmly seated in their connectors. See Figure 2-1. These connectors are also keyed. The P.C.B.'s will only go into them one way without being damaged.

2-1 0 Note the location of the game's serial number. See Figure 2-1. Check all major subassemblies to be sure they are mounted securely. These are called out in Figure 2-1. Power supply. Control panel(s). T.V. monitor. Other P.C.B.’s and/or P.C.B. rack, etc. Power Chassis assembly. . Make a note of any problems that can’t be easily corrected.

  • Call your distributor and/or service man about your problem list. ia)

INSTALLATION

  • Location requirements: O Power: Domestic 110 V @ 60 Hz Foreign 200 V to 240 V @ 50 Hz D Temperature: 32° to 100°F (0° to 38°C) D Humidity: Not over 95% relative O Space required: Upright 25” x 33” (63 x 84cm) Cocktail 32” x 22” (81 x 55cm) O Game height: Upright 70” (175cm) Cocktail 29” (73cm)
  • Voltage Selection: Your game is designed to work properly on the line voltage where you are located. Check your line voltage with a meter to determine what its value is. Then check the power input wires to the main power supply transformer on your game to be sure they are connected to taps which correspond to your line voltage value.
Page 9

SERIAL : ON/OFF NUMBER. LO SMTeH as 7 “ & CONTROL

TV. MONITOR

INTERLOCK POWER SUPPLY SWITCH

P.C.B.

POWER SUPPLY CHASSIS.

UPRIGHT REAR UPRIGHT FRONT

TV. MONITOR SERIAL NUMBER (MAY BE LOCATED ON ANY CORNER)

POWER SUPPLY P.C.B.

Cameo CONTROL PANEL (PLAYER 1) (PLAYER 2)

POWER SUPPLY CHASSIS

INTERLOCK ON/OFF SWITCH

  • UNDER TABLE SWITCH ON PLAYER 2 (INSIDE DOOR) SIDE COCKTAIL INTERIOR

Figure 2-1 Location of Serial No., Interlock Switch, On/Off Switch, & Major Sub Assys.

Page 10

If the power input wires to the main power supply transformer are not connected to taps which correspond to your local line voltage, move them to the proper taps. If the line voltage in your area falls outside the upper or lower limits of the range of inputs covered by the main power supply transformer, DO NOT PLUG YOUR GAME IN until you have talked with your distributor and/or service man and obtained a solution to this problem. Otherwise you could damage your game.

  • Interlock and power ON/OFF switches: See Figure 2-1. To help prevent the possibility of getting an electric shock while working inside the game cabinet, interlock switches have been instaJed at each cabinet access door (this DOES NOT include the coin door in the Upright models). When any access door is opened, the interlock switch installed there turns off all power to the game. Check each operation. After checking the line voltage in your area and determining that the input wires to the main power supply transformer of your game are connected properly — or — after obtaining a solution to your over or under voltage problem from your distributor and/or your service man, plug the game into your A.C. wall outlet. The game ON/OFF switches for both models are located as shown in Figure 2-1. Turn the game on and allow it to warm up a few minvtes. Slowly open each access door to the game (this does not include the coin door on the Upright models). As the door is opened approximately 1" (2.54cm) the power to the game should go off (the T.V. monitor, all the lights, and all sounds will stop). If this does not happen, check the interlock switch by this door to see if it has broken loose from its mounting or if it is stuck in the “ON” position. If the switch is found to be bad, turn the game off, unplug it, and replace the interlock switch. When done, plug the game back into the wall outlet, close the access door, and turn the game back on. After the game has warmed up, repeat the above interlock switch test. When the interlock switch is working properly and turns the power to the game off, power may be restored to the game with the access door(s) open. Take hold of the interlock switch plunger and gently pull it out to its fully extended position. THIS IS TO BE USED ONLY FOR SERVICING THE GAME. See Figure 2-2. o

interlock switch for proper

2-3 Figure 2-2 Interlock Switch Operation

SELF-TEST Your new game will Self-Test itself to see if it has any bad parts. The information it receives while testing itself will be shown on the T.V. monitor. Some information can also be heard through the game's speaker system. See the GAME OPERATION section for a more detailed description of this function. When there is a bad result according to the Self-Test, call your distributor and/or service man to have the trouble fixed unless it is something you can do yourself (such as replace a bad RAM or ROM chip).

NOTE: In order for the two SELF-TEST SWITCH- ES on the bracket located inside the cabinet at the right hand edge of the coin door frame to function properly, DIP SWITCHES 5 and 6 of SW-1 (at locations 15D on the SOUND I/O BOARD) MUST BE IN THE “OFF” POSITION.

GAME VOLUME ADJUSTMENT CONTROL See Figure 2-3. The game volume control pot is located on the Sound \/O board. The other board is the CPU board. Thereis only one pot. For adjustment, it may be reached through the rear access door on the Upright models. On the Cocktail Table model, you will have to open the table top to reach it. To make the sounds louder, turn the pot clockwise as you face it (~~ ). To make the sounds less loud, turn the pot counterclockwise as you face it (~~ ~ ).

Page 11

OPTION SWITCH SETTINGS

To change the option switch settings, you DO NOT have to take the Sound 1/O board out of the game. They can be easily reached through the rear access door on the Upright models. On the Cocktail Table model, you do have to open the table top to reach them.

When changing any options, ALWAYS put the game into the Self-Test mode, make your changes, check the results on the monitor screen, take the game out of the Self-Test mode, and play the game to be sure the switches have worked properly and that no switches were accidentally moved that were not meant to be. (These switches are small and this can happen.) The option switch settings and what they will make the game do are shown in Figure 2-4. See Figure 2-3 for option switch locations.

INCREASE

DIP SW. 2 POSITION 14D

DIP SW. 1 POSITION 15D

VOLUME CONTROL

Figure 2-3 Location of Volume Control & Option Switches

Page 12

BURGER TIME

OPTION SWITCH SETTINGS

DIP SWITCH 15D (SW1)

COINS PER CREDIT

COIN SWITCHES NO. 1 AND NO. 2 | SW#1 SW#2 SW#3 SW#4 SW#5 SW#6 SW#7 SW#8 OFF OFF *1- COIN 1- CREDIT

1- COIN2- CREDITSONOFF
1- COIN3- CREDITSOFFON
2- COINS1 - CREDITONON

TEST CREDIT BUTTON SW#1 SW#2 SW#3 SW#4 SWH5 SWHE SW#7 SW#8

*1-COIN1- CREDITOFFOFF
1- COIN2- CREDITSONOFF
1- COIN3- CREDITSOFFON
2- COINS1 - CREDITONON

DIAGNOSTICS

SW#1 SW#2 SW#3 SW#4 SW#S5 SW#6 SW#7 SW#8 OFF OFF *GAME MODE

NORMAL TEST PROCEDUREONOFF
CROSS HATCH ONLYOFFON

ON ON SOUND 1/O BOARD TEST ONLY

CABINET DESIGN

SW#H1 SW#2 SW#3 SW#4 SW#5 SWHE SWH7 SW#B ON UPRIGHT CONTROL PANEL COCKTAIL CONTROL PANELS OFF ON OFF UPRIGHT SCREEN COCKTAIL SCREEN

DIP SWITCH 14D (SW2)

NUMBER OF CHEFS PER GAME

SW#t Sw#2 SW#3 SW#4 SWHS SW#E SW#7 SW#8 OFF

*3 CHEFSOFFOFFOFF

5 CHEFS ON

BONUS CHEFS AWARDED EVERY

SW#t SW#2 SW#3 SW#4 SWHS SWHE SW#7 SW#B

OFFOFFOFF
10,000 POINTSOFFOFF
15,000 POINTSONOFF
*20,000 POINTSOFFON
30,000 POINTSONON

DIFFICULTY LEVEL OF PLAY

SW#1 SW#2 SW#3 SW#4 SWHS SW#HE SW#7 SW#8

*EASY - 4 PURSUERSOFFOFFOFFOFF

HARD - 6 PURSUERS ON

RACK BONUS

SW#H1 SW#2 SW#3 SW#4 SW#S SW#HE SW#7 SW#H8 *BONUS PEPPER AWARDED AT

END OF EACH RACKONOFFOFFOFF

NO BONUS PEPPER AWARDED AT END OF EACH RACK OFF

PART NO. M051-00333-A010 *INDICATES FACTORY RECOMMENDED SETTINGS.

Figure 2-4 Option Switch Settings

2-5

Page 13

Ill. Game Operation

BURGER TIME is a one or a two player game with a color T.V. monitor. The game gives a display which has all the parts shown below.

HIGH SCORE

PLAYER 1 SCORE

CHEF The game has five possible modes of operation: ATTRACT, READY-TO-PLAY, PLAY, HIGH SCORE/ INITIAL, and SELF-TEST.

RESERVE PEPPERS

PLAYER 2 SCORE (NOT SHOWN)

BONUS BURGER PARTS.

PURSUERS

RESERVE CHEFS

SELF-TEST MODE

The Self-Test mode is a special mode for checking the game switches and computer functions. It is the easiest and best way to check for proper operation of the entire game.

NOTE: Putting the game into Self-Test will cause it to erase any CREDITS it has on it from its memory.

You may begin a Self-Test at any time after the power to the game is on by sliding the TOP Self-Test switch to the “ON” position and activating the “TILT SWITCH”. (The “SELF-TEST” Switch(es) are ONLY READ by the game’s computer for instructions AFTER the “TILT SWITCH” has been activated or when the game is powered up.) Now that the game is in the Self-Test mode, it will react as follows:

  • First, you will see a moving multicolored pattern appear on the screen.
  • Immediately following this, a rightside up test display is shown on the monitor screen. Pushing the CREDIT BUTTON after each display is completed will cause the game to step through each of its 11 different Self-Tests. The game will remain in this Self-Test mode until you set the TOP Self-Test switch back to the “OFF” position and activate the PEPPER SYMBOL

RACK IDENTIFIER

“TILT SWITCH”. These test displays are shown on the following page.

. If a bad ROM or RAM chip is found by the game's internal check system during the Self-Test, the game indicates this to you by showing the P.C. Board location code of the bad chip(s) in place of the letters “OK”.

To check your game function switches and buttons (coin counter switches, PEPPER Button, 1 PLAYER and 2 PLAYER buttons, etc.): activate each one while the game is in the “SW TEST” section of the complete Self-Test mode. You should see a different square filled with light for each activation. If you do not see it, the switch/ button is either not working, miswired, or disconnected. Check it out thoroughly.

  • SOUND I/O BOARD TEST ONLY: To check “SOUND” (the game has 16 different sounds), slide the TOP and the BOTTOM Self-Test switches to the “ON” position and activate the “TILT SWITCH”. (The “SELF-TEST” Switch(es) are ONLY READ by the game's computer for instructions AFTER the “TILT SWITCH” has been activated or when the game is powered up.) Now 4.
Page 14

SELF-TEST DISPLAY AND BOARD LOCATION COORDINATES MAPPING OK or (incorrect address bit) RAM TEST OK or (a number and a letter, i.e. 1L, 3H, etc.) MIX TEST (if error, one or more characters will be out of sync)

FOREGROUND CHARACTER DISPLAY — (screen is filled with different parts of foreground objects) — If error has occurred, pictures will be distorted CROSS HATCH PATTERN DISPLAYED SOUND PSG1 PSG2 END CHECK 01, 02, 03, 04, 05, 06, 07, 08, 09, 10, 11, 12, 13, 14, 15, 16 ROM TEST OK or (a number and a letter, ie. 4D, 5B, etc.) SW TEST — (ACTIVATE ALL OF GAME’S INPUT SWITCHES — IF GOOD THEY WILL LIGHT A SQUARE) DIP TEST 00001011 01010000 (INDICATES WHICH OPTION SWITCHES ARE TURNED “ON” AND WHICH ARE TURNED “OFF” — 1 =“ON” & 0 =“OFF”.) BACKGROUND CHARACTER DISPLAY — (SHOWS ALL BACKGROUND MAZE CONFIGURATIONS) TILT TEST

that the game is in the Self-Test mode, it will react 6. If you wish to produce ONLY a CROSS HATCH as follows: test pattern on the monitor screen for further use, It will give the same screen display it did when the slide the BOTTOM Self-Test switch to the “ON” sounds were checked as part of the complete Self- position and activate the TILT SWITCH. The TOP Test procedure. The game will automatically Self-Test switch should REMAIN IN THE “OFF check all 16 sounds. POSITION. Pushing the CREDIT BUTTON after each display _ 5 . is completed will cause the game to step through 7. When finished with the Self-Test mode, slide the each of its SOUND P.C. BOARD Self-Tests. The BOTTOM Self-Test switch back to the “OFF” game will remain in this Self-Test mode until you Position and activate the TILT SWITCH. set the TOP and the BOTTOM Self-Test switches back to the “OFF” position and activating the“TILT 8. Normal game functions will now return to the SWITCH”. These text displays are shown below. monitor screen.

SOUND PSG1 PSG2 END CHECK 01, 02,03 04, 05, 06, 07, 08, 09, 10, 11, 12, 13, 14, 15, 16 ROM TEST OK or (a number and a letter, ie. 4D, 5B, etc.) SW TEST — (ACTIVATE ALL OF GAME’S INPUT SWITCHES — IF GOOD THEY WILL LIGHT A SQUARE) DIP TEST 00001011 01010000 (INDICATES WHICH OPTION SWITCHES ARE TURNED “ON” AND WHICH ARE TURNED “OFF” — 1=“ON” & O=“OFF”.) BACKGROUND CHARACTER DISPLAY — (SHOWS ALL BACKGROUND MAZE CONFIGURATIONS) TILT TEST

3-2

Page 15

ATTRACT MODE O After a play has been finished, the score was not high enough to put the game into the High

  • The Attract mode starts: Score/Initial mode, and there are no more credits CO Just after power has been turned on to the game. left in the game’s memory. (Self-Test switch is in the “OFF” position.) O After the High Score/Initial mode when there are D After a Self-Test has been completed. (Performing no more credits left in its memory. a Self-Test sets the credits in the game’s memory C In the Attract mode, the game will give the followto zero “O”.) ing displays centered on the monitor screen:

BURGER Tie TA be ) CRYRT, 1982 Db MFGD BY BALLY Mipweay

@ peter pepper,,

9 me HoT Dos,

@ we prcKie,,

@ me Ecc,

Attract Mode Display 1 Attract Mode Display 3

PeePEp

BURGERTIME PYRT, 1982 DOTS +¥ BALLY MIDWAY

Attract Mode Display 2 Attract Mode Display 4

3-3

Page 16

BEST FIVE PLAYERS

KEN HLT 28000 10100 9400 6550 4850 PTs PTs PTs PTs PTs

Attract Mode Display 5

O No matter where the game is in the Attract mode sequence, it will immediately go to the following display as soon as a game has been paid for. It will add the words “PUSH START BUTTON” and “CREDIT ” to the bottom of this display and the Point Value display in the Attract mode sequence. These words will remain at the bottom of these displays in the Attract mode sequence until the “1 PLAYER” start button is pushed.

ERT LME # DATA FAST ¥ DWAY ME

BEST FIVE PLAYERS

1 KEN 2H,Ir 28000 PTS 10100 PTS 9400 PTS 6550 PTs 4850 PTS 3 GON 4H.K 5 KH

PUSH START BUTTON CREDIT 4

Ready To Play Mode

3-4 READY-TO-PLAY MODE

  • The Ready-To-Play mode starts when enough coins have been accepted for a 1 or a 2 player game. . The Ready-To-Play mode ends when either the “1 PLAYER” or the “2 PLAYER” push button is pressed. . In the Ready-To-Play mode, the game will give the above modified displays centered on the monitor screen. . If no START button is pressed, the displays will remain modified indefinitely as shown above.

PLAY MODE

  • The Play mode begins when the “1 PLAYER” or the “2 PLAYER” start button is pressed. “GAME START” is displayed centered on the screen. . The Play mode ends when all of your CHEFS have been caught. When this happens, “GAME OVER” is written across the center of the monitor screen.

. When playing this game, you are the CHEF's controlling force. It is up to you to direct him through the maze of ladders and platforms to build his Burgers. Your job is to give him guidance while building his Burgers and to keep him away from his pursuers (Eggs, Hot Dogs, and Pickles). These pursuers are very sneaky and, if given half a chance, will try to corner your CHEF at the end of one of the platforms or to trap him on one of the ladders he must use to get from one level of platforms to another. . The CHEF'S pursuers have no defense mechanisms of any kind. But they CANNOT be PERMA- NENTLY eliminated either. As soon as your CHEF puts one pursuer out of commission, another appears somewhere on the screen at the edge of one of the platforms. . However, in an emergency, your CHEF can slow these pursuers down for short periods of time. This is accomplished by having him throw PEPPER on them. When hit by the PEPPER, his pursuers will be disabled for several seconds. When they are disabled like this, the CHEF can walk right over them and not be caught.

  • As your skill level increases, the number and direction of pursuers coming at your CHEF at any one time and the speed with which they move, is gradually increased; plus, their pursuit patterns become more and more devious while their overall accuracy is highly improved. . Bonus CHEFS are awarded to you periodically throughout the game as you reach or pass certain preselected point values. 4.
Page 17

. Bonus Peppers are awarded to you each time you make your CHEF run over the randomly appearing pictures of the Ice Cream Cone, the Coffee Cup, or the Fries. In addition to the bonus Peppers this obtains for you, you are also awarded bonus points each time you run over one of the above items with your CHEF.

  • When you complete the last Burger of a Rack, the screen is cleared, the next Rack appears, the number of the Rack is displayed in the lower right corner of the screen, your CHEF appears at the bottom center of the screen, and play begins anew. When the pursuers happen to catch one of your CHEFS, assuming you have at least one remaining in reserve, the words "GAME START” appear centered on the monitor screen BEFORE play begins again. . When the pursuers catch your LAST CHEF, the words “GAME OVER” are displayed centered on the monitor screen. (AT THIS POINT, SEVERAL DIFFERENT THINGS CAN HAPPEN.) If your score was one of the TOP 5, the game will go directly to the High Score/Initial mode presentation. If your score is not high enough to cause the game to go into the High Score/Initial mode, it will either go to the Attract mode (if there are no more credits left in its memory) or into the Ready-To-Play mode (if there are still credits left in its memory).

HIGH SCORE/INITIAL MODE In the High Score/initial mode the game gives a display which looks like the following:

#

uUvWwev2-, BCDEFGHIAS

LMNGOPQa@RST

eu

High Score/Initial Mode

3-5 When in the High Score/Initial mode, all the letters of the alphabet are displayed in a field above the rankings list. By moving the controller stick left, right, up, or down, you can position the CHEF under your initials one ata time. When you have him positioned properly for one of your initials, push the Pepper Button and the CHEF will take that initial down and put it in front of your score. Continue the procedure for your remaining initials.

If you do not wish to put your initials opposite your score, just press the Pepper button three times. Three “A’’s will be positioned opposite your score. After the High Score/Initial mode, the game will either go to the Attract mode (if there are no more credits left in its memory) or into the Ready-To-Play mode (if there are still credits left in its memory) Most of the above holds true in the “2 PLAYER” mode also. But there are a few minor differences.

TWO PLAYER OPERATION

The Upright and Cocktail Table models both have two player operation In the two player mode, the rules of play are the same as in the single player mode. There are some additional rules, however.

  • In the Upright model, the players must take turns at the controls.

. In the Cocktail Table model, each player has his own set of individual controls. The picture will flip to face you when itis your turn. (When it is not your turn, your set of controls will have NO effect on the game.) . Your turn lasts until the pursuers catch your CHEF. At this point, the game will do one of several things depending on whether or not the caught CHEF was your last or if you still have others remaining in reserve.

CHEF CAUGHT RESERVE

O The GAME stops. O Next, the Rack changes to the Rack number the other player is in, it displays “PLAYER __” — “GAME START” while what's left of the other player's Rack and his CHEF appears on the screen. O Play then begins for the other player. CHEF CAUGHT — NO OTHERS REMAINING IN RESERVE

O Game displays “PLAYER __” — “GAME OVER”. O After this, “PLAYER _.” — “GAME START” is displayed, the other player's Rack and his CHEF appear on the monitor screen and game play begins for the other player. OTHERS REMAINING IN

Page 18

Q After the last player has finished his game, if either or both of the scores were high enough, it goes to the “HIGH SCORE/INITIAL” mode. The player(s) that attained the high score(s) MUST REMEMBER WHAT THEIR OWN SCORE WAS!! If both players qualified, the one with the LOWEST score enters his/her initials FIRST. The one with the HIGHEST score enters his/her initials LAST. O If your score(s) were NOT high enough to cause the game to go into the “HIGH SCORE/INITIAL” mode, the game will either go to the Attract mode (if there are no more credits left in its memory) or into the Ready-To-Play mode (if there are still credits left in its memory).

3-6

Page 19

IV. Maintenance and Repair

Your NEW game needs certain types of maintenance to keep it in good working order. CLEAN, well MAINTAINED games attract players and EARN MORE PROFITS.

The most important thing for you to remember is to run the Self-Test EVERY TIME you collect money from the coin box. JUST LOOKING at your game WILL NOT tell you if all its controls and inside parts are working correctly. The Self-Test will inform you whether or not your game is working the way it should.

The second most important thing you should remember is to clean the outside of the game and coin acceptor mechanisms on a regular basis.

CLEANING

The outside of the game cabinet plus the metal can be cleaned with any non-abrasive household cleaner. However, the front of the T.V. monitor tube and both sides of all other glass and plastic on or in the game MUST be cleaned with anti-static cleaner ONLY (available from your distributor — order PART NO. 0017-00008-0098 — an 8 oz. spray bottle). For cleaning the coin acceptors: hot soapy water may be used on the plastic ones and any household cleanser may be used on the metal ones. If you wish, special coin machine cleaners that leave no residue may be purchased from your distributor. DO NOT dry-wipe any of the plastic panels. This is because any dust that was on them can scratch their surfaces. If this has happened, anyone looking through this type of damaged plastic would feel he was looking at the game through a fog. This fogging damage CANNOT be repaired or reversed. The ONLY solution is to replace the damaged piece of plastic

FUSE REPLACEMENT

This game contains several fuses located as shown in Figure 4-1. 1, UPRIGHT MODEL: As viewed from the back, facing the cabinet, with the rear access door removed; the fuses are located on the Power Chassis and Power Supply Board Assemblies.

. COCKTAIL TABLE MODEL: As viewed from the coin door side of the cabinet, with the monitor tilted open to one side; the fuses are located on the Power Chassis and the Power Supply Board Assemblies. Replace fuses ONLY with the type and size listed in the illustrated Parts Breakdown Section of this manual.

See the T.V. Monitor Manual (available on request from your distributor or the monitor manufacturer) and/or the T.V. Troubleshooting Section of this manual for information on these fuses.

FUSES LOCATED ON POWER SUPPLY BOARD AND POWER CHASSIS.

Figure 4-1 Location of Fuses

Page 20

OPENING THE CONTROL PANEL

  • UPRIGHT MODEL: See Figure 4-2. O The control panel is held in place by three latches, one on the left side, one on the right side, and one on the front center. They are spring loaded to provide constant positive pressure on their latch plates. They can be reached through the coin door AFTER turning power to the game off. To release the latches, lift up and toward the center of the control panel. Once they are released, unhook them from their latch plates. O To remove the contro! panel: Raise it up and tilt it toward you until you can see the cable behind it. Cradling the control panel between yourself and the cabinet, disconnect it from its cabling. The control panel is now free and can be removed. O To reinstall the control panel, reverse this procedure.
  • COCKTAIL TABLE MODEL: See 'Figure 4-3. O Each control panel is held in place by several screws, two on the inside of the cabinet and three

Figure 4-2 Opening the Control Panel — Upright along the outside bottom edge of the control panel. Turn power to the game off. Open the coin box door and release the two latches indicated in| Figure 4-4.

CAUTION: The right hand latch is very close to the HIGH VOLTAGE on the monitor.

Once they're released, unhook them from their latch plates. Grasp the table top at “A” and open it as indicated in |Figure 4-4,

CAUTION: Due to the weight of the monitor,

EXTREME CARE MUST be taken when opening the cabinet.

Remove the screws which secure the control panel in place. See Figure 4-3. O To remove the control panel(s): Disconnect it from its cabling. The control panel is now free and can be removed. QO To reinstall the control panel, reverse this procedure.

LuFT CONTROL UP

\ REMOVE

  • SCREWS _ EACH SIDE

Figure 4-3 Removing the Control Panel — Cocktail

Page 21

CLAMPS

Figure 4-4 Opening the Cocktail Game

REMOVAL OF THE MAIN-DISPLAY-GLASS AND/OR THE T.V. BEZEL ASSEMBLY

  • UPRIGHT MODEL: See Figure 4-5.
NOTE: In order to do this, the control panel MUST be removed first. See the “UPRIGHT MODEL” procedure. C Turn the power to the game off and remove the control panel. This frees the main-display-glass so it can be lifted up. 0 By putting your finger in the hole in the middle of the main-display-glass support, you can lift it up and out. © Loosen the screws which secure the T.V. bezelglass-clamps in place. Move the clamps to the side and the bezel glass may be removed. Remove the above mentioned screws and the bezel with four bezel-glass-clamps may be removed. O To reinstall the T.V. bezel assembly and the maindisplay-glass, reverse this procedure.
  • COCKTAIL TABLE MODEL: See Figure 4-6.
NOTE: This may be done with the table top in the open or the closed position. If you decide to open the table top, TURN THE POWER TO THE GAME OFF FIRST. 1 Remove the screws which secure the table top glass clamps in place. O Remove the table top glass. C Loosen the screws which secure the T.V. bezelglass-clamps in place.

4-3 Move the clamps to the side and the bezel glass may be removed. Remove the screws which secure the bezel assembly to the table top and the bezel with four bezel-glass-clamps may be removed. C To reinstall the T.V. bezel and the table top glass, reverse this procedure.

DISPLAY GLASS

Figure 4-5 Removing the Main Display Glass & T.V. Bezel — Upright

Page 22

Figure 4-6 Removing the Top Glass & T.V. Bezel — Cocktail

T.V. MONITOR REPLACEMENT

CAUTION: High voltages may exist in any television unit, even with the power disconnected. Use EXTREME CAUTION and do not touch electrical parts or the T.V. yoke area with your hands or with metal objects held in your hands! In addition, BE SURE TO USE HEAVY GLOVES when handling the monitor. You could cut your hands on the metal T.V. chassis without such protection.
DANGER: The TV. monitor DOES NOT contain an isolation transformer on its chassis (it is mounted instead on the floor of the cabinet). When servicing the monitor on a test bench, YOU MUST ISOLATE THE MONITOR FROM AC VOLTAGE WITH AN ISOLATION TRANSFORMER.

4-4

  • UPRIGHT MODEL: See Figure 4-7. O Turn power off to the game. © Open the rear access door. O Completely disconnect the T.V. monitor from all its cabling. DON’T FORGET THE CHASSIS GROUND WIRE. Before removing the T.V. monitor, the maindisplay-glass MUST be removed. See above “Upright Model” procedure. With the removal of only four bolts, the T.V. monitor will be loose. The monitor mounting channels slide on top of and against two metal guides mounted to the cabinet’s right and left sides. The monitor is removed by sliding it out the back of the cabinet. See Figure 4-7. To reinstall the T.V. monitor, procedure. After replacing the T.V. monitor, be sure to run the game Self-Test. reverse this

REMOVE (4) ‘BOLTS

Figure 4-7 Removing the Monitor — Upright

Page 23

CLAMPS

Figure 4-8 Opening the Cocktail Game

  • COCKTAIL TABLE MODEL: See Figure 4-9. 0 Turn power off to the game. Open the coin box door and release the two latches indicated in Figure 4-8.
CAUTION: The right hand latch is very close to the HIGH VOLTAGE on the monitor.

O Once the latches are released, unhook them from their latch plates. 0 Grasp the table top at “A” and open it as indicated in Figure 4-8.

CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet.

© Remove the screws which hold the table top glass clamps in place. O Remove the table top glass. O Lift out the T.V. bezel assembly. O Completely disconnect the T.V. monitor from all its cabling. DON’T FORGET THE CHASSIS GROUND WIRE. O Remove the screws holding the T.V. monitor chassis to the “L” brackets by the door hinge(s). See Figure 4-9. 0 Close the Cocktail Table and re-latch it. Remove the screws which secure the T.V. monitor mounting brackets to the edges of the slot cut in the table top. See Figure 4-9. O Pry up the end of each monitor mounting bracket with a screwdriver or similar tool until you can grasp them both.

4-5 D Lift the T.V. monitor straight up and out of the table top being VERY CAREFUL not to bump the neck of the picture tube. O To reinstall the T.V. monitor, procedure. Be sure to check the clearance of the “L” brackets BEFORE setting the monitor into the table top. Q After replacing the T.V. monitor, be sure to run the game Self-Test. reverse this

REMOVE (6) SCREWS (3 EACH SIDE) AND LIFT MONITOR STRAIGHT UP

REMOVE (4) SCREWS (2 EACH SIDE)

Figure 4-9 Removing the Monitor — Cocktail Game

Page 24

PRINTED CIRCUIT BOARD (P.C.B.) REPLACEMENT

  • UPRIGHT MODEL: See Figure 4-10. Q Turn the power to the game off.

O Unlock and open the rear access door.

O Disconnect the Sound I/O board from all its cabling. O Disconnect the CPU board from all its cabling. OD Slide the P.C.B. clamps to one side, remove the P.C.B.’s from the card rack and take them out the back of the cabinet.

Q Disconnect the Power Supply board from all its cabling, remove the P.C.B. supports indicated in Figure 4-10, and slide it out the back of the cabinet. O To reinstall the above P.C.B.’s, procedure. reverse this

NOTE: P.C.B.’s are all keyed and will ONLY fit into their connectors one way without forcing them. The plugs on the cable harness which connect it to the P.C.B.’s are also keyed and will ONLY go onto their connectors one way without forcing them.
  • COCKTAIL TABLE MODEL: See Figure 4-10. O Turn the power off to the game.

O Open the cabinet: Open the coin box door and release the two latches indicated in Figure 4-8.

REMOVE SUPPORT FROM SIDE OF CABINET AND LIFT P.C.B.S UP TO REMOVE REMOVE SUPPORT AND LIFT POWER SUPPLY BOARD UP TO REMOVE

CAUTION: The right hand latch is very close to the HIGH VOLTAGE on the monitor.

Once they're released, unhook them from their latch plates. O Grasp the table top at “A” and open it as indicated in Figure 4-8.

CAUTION: Due to the weight of the monitor,

EXTREME CARE MUST be taken when opening the cabinet.

O To remove the Power Supply Board. See Figure 4-10. Disconnect it from all its cabling. Remove the two smallest P.C.B. supports. Once these are removed, the power supply can be lifted out the top of the cabinet. To reinstall the power supply board, reverse this procedure. To remove the Sound 1/O and CPU boards. Disconnect the Sound 1/O board from all its cabling. Disconnect the CPU board from all its cabling. Slide the P.C.B. clamps to one side, remove the P.C.B.'s from the card rack and lift them out the top of the cabinet. To reinstall the Sound I/O and CPU boards, reverse this procedure.

COCKTAIL REMOVE (2) SUPPORTS TO REMOVE POWER SUPPLY BOARD FROM CABINET REMOVE BRKT. FROM SIDE OF CABINET TO REMOVE P.C.B.S

Figure 4-10 Removing P.C.B.s

Page 25

OPENING THE ATTRACTION PANEL

  • UPRIGHT MODEL: See Figure 4-11. 0 Turn the power to the game off.

D Opening the attraction panel: Remove the screws which secure the top bracket in place. (They are on its top side.) Remove the top bracket and slide up the attraction panel. This exposes the attraction panel fluorescent light tube and its mounting bracket assembly. To reinstall the attraction panel, reverse this procedure. O The fluorescent light tube may be replaced at this time. BE CAREFUL NOT TO DROP IT.

WARNING: If you drop a fluorescent tube and it breaks, IT WILL IMPLODE! Shattered glass can fly six (6) feet or more from the implosion. Use care when replacing any fluorescent tube.

O Replacing the fluorescent tube starter. See Figure 4-12. Be sure the power to the game has been turned off. Grasp the starter (it is on the back of the mounting bracket), give it a quarter turn, and remove it from its socket. To replace the fluorescent light tube starter, reverse this procedure. Replacement of the fluorescent tube mounting bracket assembly. Be sure the power is off to the game. Disconnect it from its power cable. Remove the screws at its right and left hand sides which secure it and gently slide it out the front of the cabinet, being careful not to catch its power cable on anything. To reinstall the fluorescent tube mounting bracket assembly, reverse this procedure.

1/4 TURN TO REPLACE m™ REMOVE SCREWS ON TOP AND LIFT ATTRACTION _ PANEL UP

Figure 4-11 Opening the Attraction Panel — Upright

O Replacing the speaker. Be sure the power is off to the game. Remove the attraction panel and disconnect the speaker from its cabling. Remove the nuts and bolts which secure the speaker and speaker grill in place and set them and the speaker grill aside. Once the bolts which secure the speaker in place are removed, the speaker may be removed through the opening where the attraction panel was. Reverse this procedure to reinstall the speaker.

  • THE COCKTAIL TABLE MODEL HAS NO BACK- LIT ATTRACTION PANEL.

i FLUORESCENT | TUBE STARTER

Figure 4-12 Replacing Fluorescent Tube Starter

4-7

Page 26
Scan of page 26

This page is a drawing, shown as the original scan.

Page 27

NO. 333 — BURGER TIME — UPRIGHT — FRONT

5-2

Page 28

NO. 333 — BURGER TIME — UPRIGHT — FRONT — PARTS LIST

0333-00901-00XF 0537-00903-0057 0574-00903-0100 0017-00101-0138 0017-00009-0522 A595-0001 1-0000 0017-00009-0393 0017-00003-0259 0017-00101-0127 0017-00103-0061 0508-00900-0000 0333-00902-0000 0508-00901 -0000 0017-00101-0017 0333-00900-00XF 0508-00108-0000 0017-00101-0027 A316-00012-0000 0333-00903-0000 0941-00103-0100 0941-00103-0200 0555-00901-0000 0017-00009-0534 0017-00101-0141 0316-00903-0000 A982-00017-0000 A316-00005-0000 0333-00904-0000 0017-00042-0257 0017-00032-0093 0017-00103-0054 A090-00300-11BK A982-00015-0000 0090-00002-04BK 0017-00101-0121

0935-00906-0100 0017-00102-0048 0017-00103-0026 ORDER BY PART NUMBER ONLY

HEADER DISPLAY PLEX! GLASS CHANNEL — 7-5/8" LG. (2 REQ’D.) HEADER BRKT. RETAINER (2 REQ'’D.) #8 x 5/8 TORX TAMPER RESISTANT SCR. (6 REQ'’D.) LONG ARM KEY T-20 (FOR ABOVE SCREW) HEADER LIGHT ASSY. BLACK SPEAKER GRILL W/SLOTS 6" x 9” SPEAKER — 8 OHM, 7W. #8-32 x 1-1/2 CARRIAGE BOLT (4 REQ'’D.) #8-32 HEX NUT W/SEMS (4 REQ'D.) 19" T.V. BEZEL DIFFUSER PLEXI-GLASS CLIPS (4 REQ’D.) #6 x 1/2 BLK. SLT. HEX HD. SCREW (4 REQ'D.) MAIN VIEWING GLASS GLASS STOP BRKT. #8 x 3/4 SLT. HEX HD. M.S. (3 REQ'D.) CONTROL SHELF PLATE WELD ASSY. W/STRIKES DECORATIVE CONTROL SHELF OVERLAY CONTROL SHELF MTG. BRKT. — RIGHT CONTROL SHELF MTG. BRKT. — LEFT PLASTIC LOCATING PIN (4 REQ'D.) BASSICK CLAMP (3 REQ'D.) #8 x 11/16 UNSLOT. HEX HD. SCR. (10 REQ'D.) CONTROL SHELF STRAP CONTROL ASSEMBLY CONTROL SHELF CABLE ASSY. PUSH BUTTON ASSY. — WHITE (PRINTED) (2 REQ’D.) PUSH BUTTON ASSY. — YELLOW (2 REQ'D.) PUSH BUTTON SWITCH W/HOLDER (4 REQ'D.) 5/8-11 PAL NUT (4 REQ'D.) U.S.A. 25¢ DOUBLE COIN DOOR ASSY. COIN DOOR CABLE ASSY. BLACK LARGE COIN DOOR FRAME #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ'’D.) (MOUNTS COIN DOOR TO FRAME) KICK PLATE — 23" LG. 3/8-16 x 2" LEG LEVELERS (4 REQ’D.) 3/8-16 LEG LEVELER HEX NUTS (4 REQ'D.)

5-3

Page 29

NO. 333 — BURGER TIME — UPRIGHT — REAR ACCESS

5-4

Page 30

NO. 333 — BURGER TIME — UPRIGHT — REAR ACCESS — PARTS LIST

ORDER BY PART NUMBER ONLY

DESCRIPTION

ON-OFF SWITCH & PLATE ASSY. PLASTIC PULL & VENT (2 REQ’D.) #8 x 11/16 UNSLOT. HEX HD. M.S. (8 REQ’D.) ELECTROHOME — 19” COLOR DUAL SYNC. HORIZ. MTG. MONITOR (OR) WELLS-GARDNER — 19” COLOR DUAL SYNC. HORIZ. MTG. MONITOR MONITOR MTG. CHANNEL ASSY. (2 REQ'D.) 1/4-20 x 3/4 UNSLOT. HEX HD. BOLT (4 REQ'D.) 7/8" DISH WASHER (4 REQ'D.) MONITOR RAIL (2 REQ’D.) PLASTIC LOCATING PINS (4 REQ’D.) #8 x 11/16 UNSLOT. HEX HD. M.S. (8 REQ'D.) 19" T.V. BEZEL GLASS STOP BRKT. #8 x 3/4 SLT. HEX HD. MLS. (3 REQ’D.) INTERLOCK SWITCH & SPRING BRKT. ASSY. POWER SUPPLY P.C. BOARD ASSY. P.C. SUPPORT BRKT. — 10” LG. (2 REQ’D.) P.C. SUPPORT BRKT. — 4” LG. #8 x 11/16 UNSLOT. HEX HD. MS. (11 REQ’D.) #8 FLAT WASHER (11 REQ'D.) POWER CHASSIS ASSY. — 70VA., 115V. CARD RACK HOLDER W/BOARDS ASSY. SOUND BRD. P.C. ASSY. CPU BRD. P.C. ASSY. COIN BOX ASSY. (NOT SEEN) COIN BOX CRADLE ASSY. COIN BOX COVER COIN BOX HANDLE COIN DEFLECTOR (2 REQ'D.) LARGE PLASTIC CASH BOX 1/4-20 x 1-3/8 BLACK RND. HD. BOLT (4 REQ’D.) 7/8" DISH WASHER (4 REQ’D.) 1/4-20 HEX NUT (4 REQ'D.) CASTER ASSY. (2 REQ'’D.) WHEEL BRKT. (2 REQ'D.) PLASTIC WHEEL (2 REQ’D.) SHAFT (2 REQ'D.) 3/8" E-RING (2 REQ’D.) LINE CORD ASSY. ITEM PART NO.

A945-00038-0000 0894-00916-0000 0017-00101-0141 0017-00003-0339

0017-00003-0439

A508-00005-0000 0017-00102-0066 0017-00104-0014 0595-00104-0000 0555-00901-0000 0017-00101-0141 0508-00900-0000 0508-00108-0000 0017-00101-0027 A088-00016-0000 A082-90427-A000 0624-00902-0200 0624-00902-0400 0017-00101-0141 0017-00104-0037 A945-00036-0002 A334-00010-0000 A084-91440-D333 A084-91441-E333 A950-00004-0000 A950-00006-0000 0950-00105-0000 0950-00104-0000 0950-00101-0000 0950-00900-0000 0017-00101-0142 0017-00104-0014 0017-00103-0018 A961-00007-0000 0961-00109-0000 0017-00042-0255 0894-00702-00XF 0017-00100-0037 A945-00019-0000 ADDITIONAL PARTS LIST

CARD RACK SUB-ASSY. BACK DOOR LOCK ASSY. 5-5/8" SQR. VENT GRILL (4 REQ'D.) CREDIT SWITCH & BRKT. ASSY. COIN BOX DIVIDER — OPTIONAL MASTER CABLE W/BRKT. ASSY. HIGH VOLTAGE CABLE ASSY. LOW VOLTAGE CABLE ASSY. A334-00014-0000 A151-00098-0000 0017-00009-0490 A333-00012-0000 0950-00103-0000 A333-00008-0000 A316-00009-0000 A316-00010-0000

5-5

Page 31

NO. 334 — BURGER TIME — COCKTAIL — FRONT

5-6

Page 32

NO. 334 — BURGER TIME — COCKTAIL — FRONT — PARTS LIST

ORDER BY PART NUMBER ONLY

ITEM PART NO. DESCRIPTION

0017-00009-0499 COVER GLASS — 32” x 22” x 1/4” 0334-00900-0000 DECORATIVE ARTWORK UNDERLAY 0775-00104-O00XF GLASS CLIPS (8 REQ'D.) 0017-00101-0117 #8 x 5/8 BLK. PHIL. TRS. HD. SCR. (8 REQ’D.) 0557-00900-0000 T.V. BEZEL 0333-00902-0000 DIFFUSER 0508-00901-0000 PLEXI-GLASS CLIPS (4 REQ'D.) 0017-00101-0017 #6 x 1/2 SLT. HEX HD. SCR. (4 REQ'D.) A334-00004-0100 CONTROL SHELF ASSY. — PLAYER #1 A334-00004-0200 CONTROL SHELF ASSY. — PLAYER #2 0017-00009-0393 BLACK SPEAKER GRILL W/SLOTS (2 REQ’D.) 0017-00009-0482 SPEAKER GRILL (NOT SEEN) 0017-00003-0187 6" x 9" SPEAKER — 8 OHM, 9W. 0017-00101-0136 #8-32 x 1-1/4 CARRIAGE BOLT (8 REQ'D.) 0017-00101-0127 #8-32 x 1-1/2 CARRIAGE BOLT (4 REQ'D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (12 REQ'D.) A090-00300-11BK U.S.A. 25¢ DOUBLE COIN DOOR ASSY. A982-00015-0000 COIN DOOR CABLE ASSY. 0090-00002-04BK LARGE COIN DOOR FRAME 0017-00101-0121 #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ'D.) (MOUNTS COIN DOOR TO FRAME) A927-00019-0000 COIN BOX ASSEMBLY A962-00004-0000 COIN BOX COVER ASSY. A962-00005-0000 COIN BOX SIDE CHANNEL ASSY. — SHORT 0962-00101-0000 COIN BOX SIDE CHANNEL — SHORT 0017-00101-0628 #8-32 x 3/4 CARRIAGE BOLT (4 REQ’D.) 0017-00104-0022 #8 FLAT WASHER (4 REQ'D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (4 REQ'D.) 0017-00102-0048 3/8-16 x 2” LEG LEVELERS (4 REQ'D.) 0017-00103-0026 3/8-16 LEG LEVELER HEX NUTS (4 REQ'D.)

5-7

Page 33

NO. 334 — BURGER TIME — COCKTAIL — INTERIOR ACCESS

Page 34

NO. 334 — BURGER TIME — COCKTAIL — INTERIOR ACCESS — PARTS LIST

ORDER BY PART NUMBER ONLY

PART NO. DESCRIPTION 0017-00003-0339 ELECTROHOME — 19” COLOR DUAL SYNC. HORIZ. MTG. MONITOR (OR) 0017-00003-0439 WELLS-GARDNER — 19” COLOR DUAL SYNC. HORIZ. MTG. MONITOR A515-00019-0000 | MONITOR SUPPORT ASSY. — LEFT ‘A515-00019-0100 | MONITOR SUPPORT ASSY. — RIGHT 0017-00101-0109 #8 x 5/16 UNSLOT. HEX HD. BOLT (6 REQ'D.) 0610-00132-00ZN | STRIKE (2 REQ’D.) 0017-00009-0534 BASSICK CLAMP (2 REQ’D.) 0017-00101-0141 #8 x 11/16 UNSLOT. HEX HD. M.S. (8 REQ’D.) 0927-00101-00xF | SUPPORT ANGLE (2 REQ’D.) 0017-00101-0598 #8-32 x 5/16 SLT. HEX HD. SCREW (4 REQ’D.) 0017-00009-0514 2-1/2" HINGE (2 REQ’D.) 0017-00101-0136 #8-32 x 1-1/4 CARRIAGE BOLT (8 REQ'D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (8 REQ'D.) 0334-00901-0100 DECORATIVE OVERLAY PLAYER #1 0334-00901-0200 DECORATIVE OVERLAY PLAYER #2 A302-00015-0000 | CONTROL PANEL WELDMENT ASSY. (2 REQ’D.) 0510-00101-00XF | BOTTOM PAN (2 REQ’D.) 0017-00101-0341 #6 x 1/4 PHIL. TRS. HD. SCR. (6 REQ’D.) A982-00017-0000 | CONTROL ASSY. (2 REQ’D.) A334-00008-0100 | CONTROL SHELF CABLE ASSY. — PLAYER #1 A334-00008-0200 | CONTROL SHELF CABLE ASSY. — PLAYER #2 0017-00032-0051 SMALL RED BUTTON SWITCH ASSY. W/HARDWARE (2 REQ’D.) 0333-00904-0000 PUSH BUTTON ASSY. W/PRINTING (2 REQ’D.) 0017-00032-0093 PUSH BUTTON SWITCH W/HOLDER (2 REQ’D.) 0017-00103-0054 5/8-11 PAL NUT (2 REQ'’D.) 0930-00104-0000 CONTROL PANEL LOCATING BRKT. (4 REQ’D.) 0017-00101-0025 #8 x 1/2 SLT. HEX HD. M.S. (16 REQ'D.) 0930-00904-0000 LIGHT SHIELD (2 REQ’D.) 0017-00031-0044 WEDGE BASE LAMP SOCKET (4 REQ’D.) 0017-00003-0219 #194 WEDGE LAMP — 14V., .27A. (4 REQ'D.) 0017-00101-0555 #6-32 x 5/16 SLT. HEX HD. M.S. (4 REQ’D.) ‘A082-90427-A000 | POWER SUPPLY P.C. BOARD ASSY. 0624-00902-0400 P.C, SUPPORT BRKT. — 4” LG. 0624-00902-0200 P.C, SUPPORT BRKT. — 10” LG. (2 REQ’D.) 0017-00101-0141 #8 x 11/16 UNSLOT. HEX HD. M.S. (7 REQ’D.) 0017-00104-0037 #8 FLAT WASHER (7 REQ’D.) A945-00036-0000 | POWER CHASSIS ASSY. — 70VA., 115V. 0942-00102-0000 POWER CHASSIS MTG. BRKT. (2 REQ’D.) A334-00010-0000 | CARD RACK HOLDER W/BOARDS ASSY. A084-91440-D333 | SOUND BRD. P.C. ASSY. A084-91441-E333 | CPU BRD. P.C. ASSY.

5-9

Page 35

NO. 334 — BURGER TIME — COCKTAIL — INTERIOR ACCESS — PARTS LIST (Continued)

ORDER BY PART NUMBER ONLY

A775-00013-0000 FAN ASSY. 0151-00081-0000 4" FAN 0775-00110-00XF FAN PLATE 0749-00106-00XF VENT SCREEN 0017-00101-0347 #6-32 x 1/2" R.H.M.S. (4 REQ’D.) 0017-00104-0009 #6 EXT. WASHER (4 REQ'’D.) 0017-00103-0005 #6-32 HEX NUT (4 REQ'D.) 0017-00101-0026 #8 x 5/8 SLT. HEX HD. SCREW (4 REQ'D.) 0017-00003-0187 6" x 9" SPEAKER — 8 OHM, 9W. 0942-00902-0000 MONITOR SHIELD

ADDITIONAL PARTS LIST A088-00014-0000 INTERLOCK SWITCH & BRKT. ASSY. A945-00038-0000 ON-OFF SWITCH & PLATE ASSY. A334-00005-0000 MASTER CABLE W/BRKT. ASSY. A317-00006-0000 HIGH VOLTAGE CABLE ASSY. A316-00010-0000 LOW VOLTAGE CABLE ASSY. 0942-00902-0000 MONITOR SHIELD A927-00005-0000 HIGH BASE LEG KIT ASSY. — OPTIONAL A334-00014-0000 CARD RACK SUB-ASSY.

BURGER TIME — CONTROL ASSEMBLY — ALL VERSIONS — PARTS LIST

ORDER BY PART NUMBER ONLY

ITEM PART NO. DESCRIPTION

A932-00022-0000 BALL & SHAFT ASSEMBLY 0017-00100-0025 1/4 E-RING 0921-00702-0000 STOP SPACER 0921-00902-0000 SLIDE PLATE A982-00019-0000 PIVOT PLATE WELD ASSY. 0017-00101-0637 #8-32 x 1" CARRIAGE BOLT (4 REQ'D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (4 REQ’D.) 0932-00902-0000 GROMMET 0017-00101-0598 #8-32 x 5/16 SLT. HEX HD. M.S. (10 REQ’D.) 0962-00904-0000 SLEEVE 0017-00101-0527 #5-40 x 5/8 SLT. RND. HD. SCR. (8 REQ’D.) 0020-00202-0000 SWITCH PLATE (4 REQ'D.) A932-00009-0000 SWITCH ASSEMBLY (4 REQ’D.) A932-00012-0000 STOP PLATE & SWITCH BRKT. ASSY. 0932-00905-0000 WEAR PLATE 0921-00700-0000 ACTUATOR CHONMANDRYON=

5-10

Page 36

BURGER TIME — CONTROL ASSEMBLY — ALL VERSIONS

5-11

Page 37

BURGER TIME — POWER CHASSIS ASSY. — 70VA, 115V. — ALL VERSIONS

Page 38

BURGER TIME — POWER CHASSIS ASSY. — 70VA, 115V. — ALL VERSIONS — PARTS LIST

0945-00108-00XF A945-00029-0000 0945-00107-01XF 0017-00101-0123 MT00-00101-A000

0017-00103-0061 MTO00-00105-A000

MTO00-00105-B000

0017-00103-0061 0945-00902-0000 0017-00101-0067 0945-00103-00XF A945-00030-0400 0017-00021-0297 A945-00030-0300 A945-00030-0500 A945-00030-0200 A945-00021-0000 0017-00101-0573 0017-00103-0084 A945-00025-0000 0017-00021-0510 0017-00101-0140 0017-00101-0660 0017-00104-0107 0017-00103-0081 0017-00003-0263 0017-00003-0005 0017-00003-0444

0945-00904-0000 0945-00908-0000 0017-00003-0217 0017-00003-0007 0017-00003-0263 0945-00903-0000 0017-00101-0067 0017-00101-0780 0017-00021-0629 A945-00019-0000 ORDER BY PART NUMBER ONLY

ITEM PART NO. DESCRIPTION

CHASSIS MTG. PLATE & BARRIER ASSY. STRAP (2 REQ'D.) #8 x 1/4 UNSLOT. HEX HD. SCR. (12 REQ'D.) ISOLATION TRANSFORMER W/O SHIELD ASSY. — 115V., 50/60 HZ. #8-32 HEX NUT W/SEMS (4 REQ’D.) POWER TRANSFORMER W/O SHIELD — 70VA, 115V. (UPRIGHT ONLY) POWER TRANSFORMER W/SHIELD — 70VA, 115V. (COCKTAIL ONLY) #8-32 HEX NUT W/SEMS (4 REQ’D.) SNAP BUSHING (3 REQ’D.) #6 x 3/8 PHIL. PAN HD. SCR. (11 REQ’D.) PARTITION — LOCATED UNDER CHASSIS (NOT SEEN) CONNECTOR & CABLE ASSY. 2 POSITION CONNECTOR CONNECTOR & CABLE ASSY. CONNECTOR & CABLE ASSY. CONNECTOR & CABLE ASSY. CONVENIENCE OUTLET ASSY. #6-32 x 1/2 PHIL. RND. HD. SCR. (2 REQ’D.) #6-32 HEX NUT W/SEMS (2 REQ'D.) FILTER ASSY. — 125V. — UNDER CHASSIS (NOT SEEN) TERMINAL STRIP #4-40 x 5/16 PHIL. PAN HD. SCR. (2 REQ’D.) #10-32 x 3/4 SLT. PAN HD. SCREW (NOT SEEN) #10 FLAT WASHER #10-32 HEX NUT W/SEMS SLO-BLO FUSE — 4A., 250V. FUSE — 2A, 250V. FUSE HOLDER — QUICK CONN. (2 REQ’D.) — FOR ABOVE FUSES 5 POSITION FUSE HOLDER FUSE BLOCK INSULATOR SLO-BLO FUSE — 2.5A., 250V. (2 REQ’D.) SLO-BLO FUSE — 3A., 250V. (2 REQ'D.) SLO-BLO FUSE — 4A., 250V. FUSE HOLDER BARRIER #6 x 3/8 PHIL. PAN HD. SCREW (2 REQ’D.) #6 x 1/2 PHIL. PAN HD. SCREW (2 REQ'D.) 5 POSITION TERMINAL STRIP (UNDER CHASSIS) LINE CORD ASSY. — 115V. (NOT SHOWN)

5-13

Page 39

FRONT DOOR ASSEMBLY — U.S.A. 25¢

5-14

Page 40

FRONT DOOR ASSEMBLY — U.S.A. 25¢ — PARTS LIST

ORDER BY PART NUMBER ONLY

PART NO. DESCRIPTION

10090-00002-04BKDOUBLE ENTRY COIN DOOR FRAME
20017-00101-0121#6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ’D.)
3A090-00073-02BKDOUBLE ENTRY COIN DOOR W/DRESS PLATE
40017-00101-0123#8 x 1/4 UNSLOT. HEX HD. SCREW (12 REQ’D.)
50017-00007-0019KEY HOOK
60017-00103-0059PUSH NUT (4 REQ’D.)
70090-00912-0000COIN ENTRY PLATE — 25¢ (2 REQ’D.)
8A097-00005-0000DOOR LOCK & KEY W/SCREW & NUT (OR)
8A097-00006-0000DOOR LOCK & KEY W/SCREW & NUT
90090-00128-00XFDOOR TILT SWITCH BRKT.

DOOR CAM DOOR TILT SWITCH SWITCH BACK-UP PLATE #5-40 x 9/16" PHIL. HD. M.S. (2 REQ'D.) DOOR TILT SWITCH & BRKT. ASSY. (ITEMS 9 & 11 THRU 13) 25¢ WINDOW (2 REQ’D.) COIN PLEX RETAINER 12 VOLT LAMP — G.E. #194 (2 REQ'D.) WEDGE SOCKET W/BRKT. (2 REQ’D.) BRKT. ASSY. #6-32 HEX NUT W/SEMS (4 REQ’D.) COIN METER W/DIODE #6 x 1/4 UNSLOT. HEX HD. SCR. (4 REQ'’D.) INSULATOR (2 REQ’D.) COIN CHUTE & INSULATOR ASSY. (2 REQ’D.) 0017-00005-0041 A090-00095-0000 0090-00126-03XF 0017-00101-0525 A090-00096-0000 0090-00903-9500 0090-00143-00XF 0017-00003-0219 0017-00031-0048 A090-00100-0000 0017-00103-0084 A090-00089-0000 0017-00101-0124 0090-0091 1-0000 A090-00112-0000 0010-00134-0000 SPRING 0010-00181-0000 SPRING 0017-00007-0083 1/8 x 1-5/8 ROLL PIN 0090-00129-00XF PIVOT POST 0090-00167-00XF PIVOT LEVER 0090-00182-00XF REJECT LEVER 0017-00100-0018 E-RING A090-00088-0000 A090-00105-0000 0017-00005-0003 0017-00005-0211 0017-00005-0214 A090-00064-0000 0017-00101-0099 0090-00162-00XF 0017-00005-0203 0017-00005-0195 0010-00599-0000 0017-00007-0015 A090-00059-0400 0017-00101-0147 A090-00077-0000 REJECT LEVER ASSY. (2 REQ’D.) (ITEMS 30 THRU 33) COIN ACCEPTOR FRAME ASSY. (2 REQ’D.) COIN ACCEPTOR W/STRING CUTTER (2 REQ'’D.) (OR) COIN ACCEPTOR W/ANTI STRING DEVICE (2 REQ'D.) (OR) COIN ACCEPTOR W/STRING CUTTER (2 REQ'D.) ANTI-PENNY DEVICE #6 x 1/4 SLT. HEX HD. MS. (2 REQ'D.) COIN SWITCH MTG. BRKT. COIN SWITCH CHUTE COIN SWITCH COIN SWITCH WIRE PUSH-ON RING COIN SWITCH & WIRE ASSY. (ITEMS 40 THRU 42) #4-40 x 3/4 PHIL. PAN. HD. M.S. (2 REQ’D.) COIN GUIDE & SWITCH ASSY. (ITEMS 38 THRU 43)

5-15

Page 41

NO. 333 — BURGER TIME — UPRIGHT — HEADER FLUORESCENT LIGHT ASSY.

NO. 333 — BURGER TIME — UPRIGHT — HEADER FLUORESCENT LIGHT ASSY. — PARTS LIST

ORDER BY PART NUMBER ONLY

ITEM PART NO. DESCRIPTION

0595-00105-0000 FLUORESCENT BRKT. 0017-00003-0043 18" COOL WHITE FLUORESCENT LAMP 0017-00003-0445 LAMP LOCKS (2 REQ'’D.) 0017-00031-0036 FLUORESCENT SOCKET (2 REQ'’D.) 0017-00003-0412 FLUORESCENT STARTER HOLDER W/LEADS 0017-00101-0573 #6-32 x 1/2 PHIL. RND. HD. M.S. (4 REQ’D.) 0017-00104-0009 #6 EXT. WASHER (4 REQ’D.) 0017-00003-0019 FLUORESCENT STARTER 0017-00003-0026 BALLAST 0017-00101-0598 #8-32 x 5/16 SLT. HEX HD. SCR. (4 REQ’D.) A961 -00042-0000 LINE FILTER ASSY.

5-16

Page 42

VI Technical Troubleshooting

Introduction

The most common problems occur in harness components such as the coin acceptor, player controls, interconnecting wiring, etc. The TV monitor and PCB computer cause their share of problems too, but not as much as the harness and its component parts. TV monitor troubleshooting will not be covered here because it is covered in that section of this manual. As you already know, the PCB computer is a complex device with a number of different circuits. Some circuits remain basically the same among games, but overall there are a great many differences between them. PCB troubleshooting procedures, therefore, can be lengthy and will differ greatly among games. However, some basic Z-80 CPU information is involved in this section.

General Suggestions

The first step in any troubleshooting procedure is correctly identifying the malfunction’s symptoms. This includes not only the citcuits or features malfunctioning, but also those still operational. A carefully trained eye will pick up other clues as well. For instance, a game in which the computer functions fail completely just after money was collected may have a quarter shorting the PCB traces. Often, an experienced troubleshooter will be able to spot the cause of the problem even before opening the cabinet. After all the clues are carefully considered, the possible malfunctioning areas can be narrowed down to one or two good suspects. Those areas can be examined by a process of elimination until the cause of the malfunction is discovered.

Harness Component Troubleshooting

Typical problems falling in this category are coin and credit problems, power problems and failure of individual features. NO GAME CREDIT For example, your prospective player inserts his quarter and is not awarded a game. The first item to check is if the quarter is returned. If the quarter is returned, the malfunction most certainly lies in the coin acceptor itself. First, use a set of test coins (both old and new) to ascertain that the player's coin is not undersize or underweight. If your test coins are also returned, coin acceptor servicing is indicated. Generally, the cause of this particular problem is a maladjusted magnet gate. Normally, this will mean slightly closing the magnet gate a little by turning the adjusting screw out a bit (see section on coin acceptor for more details). If the quarter is not returned and there is no game credit, the cause of the malfunction may be in one of several areas. First try operating the coin return button; if the coin is returned, the problem is most likely in the magnet gate. Enlarge the gap according to the coin acceptor service procedures. If this does not cure the problem, remove the coin acceptor, clean it and perform the major adjustment procedure. If the trapped coin is not returned when the wiper lever is actuated, you may have an acceptor jammed by a slug, gummed up with beer, a jammed coin chute, or mechanical failure of the acceptor mechanism. In this case, first check for the slug that will generally be trapped against the magnet. If so, simply remove the slug and test the acceptor. If the chute is blocked, remove the acceptor and remove the jammed coins. If there is actual failure of the acceptor, remove the unit and repair as indicated in the coin acceptor service procedures. If the coin is making its way through the acceptor (that is, falling into the coin box), yet there is still no game credit, you either have a mechanical failure of the coin switch or electrical failure of the coin and credit circuits. The first place to begin is by checking the coin switch. Most of these switches are the make/break variety of micro switch, which is checked by testing for continuity between the NO, NC, and C terminals. When not actuated, the NC and C terminals should be continuous and the NO terminal open. When operated, the NO and C terminals should close and the NC should be open. If the coin switch checks out, examine the connections to the terminals to make sure there is good contact. If necessary, use the continuity tester and check from the terminal lug on the switch to the associated PCB trace. This will tell you if there is a continuous line all the way to the credit circuit.

Page 43

If the coin switch wires do not check out, the problem is in the computer — most likely in the coin and credit circuitry. If you do get game credit when a coin is deposited, but the game will not start when the start switch is pressed, you may have a problem in the start switch, the interconnecting wiring or in the computer. First check the switch. If the switch is OK, proceed to check the wiring. Again, make sure you go from the terminal lug on the switch to the PCB trace. This way, you will check the terminal contact as well as PCB edge connector contact. If the wiring is continuous, proceed to check the PCB credit circuit. If not, check each section of the wiring, until the discontinuity is located. If the wiring is OK, the problem must lie in the computer.

Transformer and Line Voltage Problems

Your machine must have the correct line voltage to operate properly. If the line voltage drops too low, a circuit in the computer will disable game credit. The point at which the computer will fail to work will vary

some from game to game, but no game'will work on

line voltage that drops below 105 VAC. Low line voltage may have many causes. Line voltage normally fluctuates a certain amount during the day as the total usage varies. Peak usage times occur mainly at dawn or dusk, so if your machine’s malfunction seems to be related to the time of day, this may be a factor. A large load connected to the same line as the game (such as a large air conditioner or other device with an exceptionally large motor) may drop the line voltage significantly when starting up. This drop can result in an intermittent credit problem. In addition, poor connections in the location wiring, plug, or line cord may also cause a significant drop in power. Cold solder joints in the game's harness, especially in areas like the transformer connections, interlock switch, or fuse block, may also produce the same results, although probably on a more permanent basis. Sometimes location owners (especially in bars) replace light switches with dimmer rheostats, and the game is sometimes on the same line. Obviously, the voltage available to the game is going to drop dramatically when the dimmer is turned. In any case, the way to check for correct line voltage is with your VOM. Set the VOM to 250 VAC and stick the probes in the wall receptacle. If it's OK here, check the transformer primary connections. If you do not get 117 VAC, examine the solder joints on the transformer, fuse block, and interlock switch. If you do get 117 VAC, the problem must be either in the transformer, harness connections, or in the PCB power supply.

6-2 If you suspect the transformer, check its secondaries with the VOM set to 50 VAC and correlate the readings with the legend on the side of the transformer. The transformer must also be correctly grounded, so check the ground potential as well, especially if there is a hum bar rolling up or down the TV screen.

HARNESS PROBLEMS Other harness problems include blowing fuses and malfunctioning controls. The repeating blown-fuse problem can sometimes be quite exasperating to solve, for short circuits have the tendency to occur in areas almost impossible to find. First, try inserting a new fuse, as old fuses age and blow without cause. If the new one also blows, you definitely have a short. The best way to approach this problem is by turning the power off and disconnecting devices that may be causing the problem, such as the TV, transformer, and PCB. Disconnect the devices by pulling off their connectors, but do not allow them to touch. If necessary, insulate them with small pieces of electrical tape. Then, connect your VOM across the terminals of the fuse block (ail electrical power shut off), and set it to one of the resistance scales. This will save blowing a fuse each time you want to check the circuit. If the VOM reveals that disconnecting the devices removed the short, reconnect the devices one by one until the short returns. The last device connected is the one that is at fault. If the VOM reads a short even after the devices are disconnected, the fault must lie in the harness itself, and only patient exploration will reveal its location. First, carefully examine all the wiring, looking for terminals that may be touching, metal objects such as coins shorting connections or burned insulation. If necessary, use the VOM to check each suspected wire. MALFUNCTIONING CONTROLS One of the most common problems here is a bad potentiometer. Typically, a bad pot will cause the image to jump as it reaches a certain point. The only cure for this one is to install a new pot. If a feature that is operated by a switch (for example, joysticks, foot pedals, control panel buttons) does not operate at all, check the switch with a VOM or continuity tester to verify its operation. If the switch does not check out, replace it. If the switch is OK, you should suspect the input to the switch from the PCB. In this case, get out the harness and logic schematics and check to see what kind of input it is. In many cases, the input will be +5 VDC. If so, use the VOM to check its presence. Normally, the switch is used to pull a +5 VDC line LOW to GND or to pulla LOW line HIGH. If the PCB output is missing, check the wire length from the PCB. If you find the signal at the PCB trace, the wire length or connection is at fault. If not, begin exploring the PCB using the logic schematics.

Page 44

A Glossary of Microprocessor Terms

MICROPROCESSOR — one or several microcircuits that perform the function of a computer's CPU. Sections of the circuit have arithmetic and comparative functions that perform computations and executive instructions.

CPU — central-processing unit. A computing system’s “brain”, whose arithmetic, control and logic elements direct functions and perform computations. The microprocessor section of a microcomputer is on one chip or several chips.

PROM — programmable read-only memory. User permanently sets binary on-off bits in each cell by selectively fusing or not fusing electrical links. Nonerasable. Used for low-volume applications.

EPROM — erasable, programmable, read-only memory. Can be erased by ultraviolet light bath, then reprogrammed. Frequently used during design and development to get programs debugged, then replaced by ROM for mass production.

ROM — read-only memory. The program, or binary on-off bit pattern, is set into ROM during manufacture, usually as part of the last metal layer put onto the chip. Nonerasable. Typical ROM’s contain up to 16,000 bits of data to serve as the microprocessor's basic instructions. RAM — random-access memory. Stores binary bits as electrical charges in transistor memory cells. Can be read or modified through the CPU. Stores input instructions and results. Erased when power is turned off. LSI — large scale integration. Formation of hundreds or thousands of so-called gate circuits on semiconductor chips. Very large scale integration (VLS) involves microcircuits with the greatest component density. MOS — metal-oxide semiconductor. A layered construction technique for integrated circuits that achieves high component densities. Variations in MOS chip structures create circuits with speed and low-power requirements, or other advantages (static will damage a MOS chip).

Introduction to the

Z-80 CPU

The term “microcomputer” has been used to describe virtually every type of small computing device designed within the last few years. This term has been applied to everything from simple “microprogrammed” controllers constructed out of TTL MSI up to low end minicomputers with a portion of the CPU constructed out of TTL LSI “bit slices.” However, the major impact of the LSI technology within the last few years has been with MOS LSI. With this technology, it is possible to fabricate complete and very powerful computer systems with only a few MOS LSI components. The Zilog Z-80 family of components can be configured with any type of standard semiconductor memory to generate computer systems with an extremely wide range of capabilities. For example, as few as two LSI circuits and three standard TTL MSI packages can be combined to form a simple controller. With additional memory and I/O devices a computer can be constructed with capabilities that only a minicomputer could previously deliver. New products using the MOS LSI microcomputer are being developed at an extraordinary rate. The Zilog Z-80 component set has been designed to fit into this market through the following factors:

  • The Z-80 is fully software compatible with the popular 8080A CPU. Existing designs can be easily converted to include the Z-80. The Z-80 component set is at present superior in both software and hardware capabilities to any other microcomputer system on the market today. For increased throughput the Z80A operating ata 4 MHZ clock rate offers the user significant speed advantages. Microcomputer systems are extremely simple to construct using Z-80 components. Any such system consists of three parts:
  • CPU (Central Processing Unit)
  • Memory
  • Interface Circuits to peripheral devices The CPU is the heart of the system. Its function is to obtain instructions from the memory and perform the desired operations. The memory is used to contain instructions and in most cases data that is to be processed. For example, a typical instruction sequence may be to read data from a specific peripheral device, store it in a location in memory, check the parity and write it out to another peripheral device. Note that the Zilog component set includes the CPU and various general purpose I/O device controllers, while a wide range of memory devices may be used from any source. Thus, all required components can be connected together in a very simple manner with virtually no other external logic.
Page 45

General Purpose Registers There are two matched sets of general purpese registers, each set containing six 8-bit registers that may be used individually as 8-bit registers or as 16bit register pairs by the programmer. One set is called BC, DE and HL while the complementary set is called BC’, DE’ and HL’. At any one time the programmer can select either set of registers to work with through a single exchange command for the entire set. In systems where fast interrupt response is required, one set of general purpose registers and an accumulator/flag register may be reserved for handling this very fast routine. Only a simple exchange command need be executed to go between the routines. This greatly reduces interrupt service time by eliminating the requirement for saving and retrieving register contents in the external stack during interrupt or subroutine processing. These general purpose registers are used for a wide range of applications by the programmer. They also simplify programming, especially in ROM based systems where little external read/write memory is available. Arithmetic & Logic Unit (ALU) The 8-bit arithmetic and logical instructions of the CPU are executed in the ALU. Internally the ALU communicates with the registers and the external data bus on the internal data bus. The type of functions performed by the ALU include: Add Left or right shifts or rotates (arithmetic and logical)

Subtract Increment

Logical AND Decrement Logical OR Set bit Logical Exlusive OR Reset bit Compare Test bit Instruction Register and CPU Control As each instruction is fetched from memory, it is placed in the instruction register and decoded. The control sections performs this function and then generates and supplies all of the control signals necessary to read or write data from or to the registers, control the ALU and provide all required external control signals.

Z-80 CPU Pin Description The Z-80 CPU is packaged in an industry standard 40 pin Dual In-Line Package. The I/O pins are shown in the below figure and the function of each is described.

My, a

MREQ = SYSTEM ES CONTROL 2 iona RD wR

RFSH

HALT

cpu | wart CONTROL,

CPU BUS CONTROL Z-80 CPU

Z-80 PIN CONFIGURATION ADDRESS BUS

DATA BUS

Page 46

Ao-Ais (Address Bus) Tri-state output, active high. Aj-A;s constitute a 16bit address bus. The address bus provides the address for memory (up to 64K bytes) data exchanges and for I/O device data exchanges. I/O addressing uses the 8 lower address bits to allow the user to directly select up to 256 input or 256 output ports. Ao is the least significant address bit. During refresh time, the lower 7 bits contain a valid refresh address.

D,-D, (Data Bus) Tri-state input/output, active high. Dp-D; constitute an 8-bit bidirectional data bus. The data bus is used for data exchanges with memory and I/O devices.

M, (Machine Cycle one)__ Output, active low. M, indicates that the current machine cycle is the OP code fetch cycle of an instruction execution. Note that during execution of 2-byte op-codes, M1 is generated as each op code byte is fetched. These two byte op-codes always begin with CBH, DDH, EDH or FDH. Mi also occurs with IORQ to indicate an interrupt acknowledge cycle.

MREQ (Memory Request) Tri-state output, active low. The memory request

signal indicates that the address bus holds a valid

address for a memory read or memory write operation. 10RQ (Input/Output Request) Tri-state output, active low. The iORQ signal indicates that the lower half of the address bus holds a valid I/O address for a I/O read or write operation. An 1ORQ signal is also generated with an M1 signal when an interrupt is being acknowledged to indicate that an interrupt response vector can be placed on the data bus. Interrupt Acknowledge operations occur during M, time while I/O operations never occur during M, time. RD (Memory Read) Tri-state output, active low. RD indicates that the CPU wants to read data from memory or an I/O device. The addressed I/O device or memory should use this signal to gate data onto the CPU data bus. WR (Memory Write) Tri-state output, active low. WR indicates that the CPU data bus holds valid data to be stored in the addressed memory or I/O device.

6-5 RFSH (Refresh)

Output, active low. RFSH indicates that the lower 7

bits of the address bus contain a refresh address for dynamic memories and the current MREQ signal should be used to do a refresh read to all dynamic memories.

HALT (Halt state)

Output, active low. HALT indicates that the CPU has

executed a HALT software instruction and is awaiting either a non maskable or a maskable interrupt (with the mask enabled) before operation can resume. While halted, the CPU executes NOP’s to maintain memory refresh activity. WAIT (Wait) Input, active low. WATT indicates to the Z-80 CPU that the addressed memory or I/O devices are not ready for a data transfer. The CPU continues to enter wait states for as long as this signal is active. This signal allows memory or I/O devices of any speed to be synchronized to the CPU.

INT (Interrupt Request) Input, active low. The Interrupt Request signal is generated by I/O devices. A request will be honored at the end of the current instruction if the internal software controlled interrupt enable flip-flop (IFF) is enabled and if the BUSRQ signal is not active. When the CPU_accepts the interrupt, an acknowledge signal (IORQ during M, time) is sent out at the beginning of the next instruction cycle. The CPU can respond to an interrupt in three different modes that are described in detail in section 5.4 (CPU Control Instructions). NMI (Non-Maskable Interrupt)

Input, negative edge triggered. The non maskable

interrupt request line has a higher priority than INT and is always recognized at the end of the current instruction, independent of the status of the interrupt enable flip-flop. NM! automatically forces the Z-80 CPU to restart to location 00664. The program counter is automatically saved in the external stack so that the user can return to the program that was interrupted. Note that continuous WAIT cycles can prevent_the current instruction from ending, and that a BUSRQ will override a NMI.

RESET Input, active low. RESET forces the program counter to zero and initializes the CPU. The CPU initialization includes:

  • Disable the interrupt enable flip-flop
Page 47
  • Set Register |= 00x
  • Set Register R =00n
  • Set Interrupt Mode 0 During reset time, the address bus and data bus go to a high impedance state and all contro! ouput signals go to the inactive state.

BUSRQ (Bus Request) Input, active low. The bus request signal is used to request the CPU address bus, data bus and tri-state output control signals to go to a high impedance state so that other devices can control these buses. When BUSRQ is activated, the CPU will set these buses to a high impedance state as soon as the current CPU machine cycle is terminated. BUSAK (Bus Acknowledge) Output, active low. Bus acknowledge is used to indicate to the requesting device that the CPU address bus, data bus and tri-state control bus signals have been set to their high impedance state and the external device can now control these signals.

CLK (Clock) Single phase TTL level clock which requires only a 330 ohm pull-up resistor to +5 volts to meet all clock requirements. a Se

Page 48

VII. Coin Door Maintenance

SPECIAL NOTE: If you have any questions about the coin acceptors in your game(s), please feel free to contact their manufacturers. Each manufacturer's name is PROMINENTLY imprinted on every acceptor mechanism. Metal mechanisms only: COIN MECHANISMS, INC. 817 Industrial Drive Elmhurst, IL 60126 Phone (312) 279-9150

COIN DOOR MAINTENANCE

METAL COIN ACCEPTOR MECHANISMS

Periodically, the metal coin acceptor mechanism(s) must be removed from the coin door and cleaned.

  • Make sure the power to the game is off.
  • Unlock and open the coin door.

TO REMOVE PUSH LATCHES DOWN

PLACE PEGS IN SLOTS TO REPLACE PULL MECHANISM OUT Metal and Plastic mechanisms: COINCO COIN ACCEPTORS, INC. 860 Eagle Drive Bensenville, IL 60106 Phone (312) 766-6781

. Remove the coin acceptor mechanism as shown in Figure 7-1. O Push down on the two spring loaded latches. O While holding the latches down, pull the top of the coin acceptor mechanism toward you. O Release the latches and lift out the coin acceptor mechanism.

PUSH MECHANISM IN

Figure 7-1 Removing and replacing coin acceptor

Page 49
  • Clean the magnet of all foreign particles. See Figure 7-2. O This may be accomplished by swinging the gate open as shown in the above figure.
  • Remove the cradles and undersize levers and clean the bushings. (A pipe cleaner makes a good bushing cleaner.) O Also clean the pivot pin.
  • Whenever needed, the coin acceptor should be cleaned with hot water and cleanser in the following manner: O Place the coin acceptor in boiling water for about ten minutes.
CAUTION: BE CAREFUL NOT TO BURN YOUR- SELF.

O Next, use a brush and kitchen cleaner to remove all remaining foreign matter from the unit. O Rinse the coin acceptor in clean boiling water. O Dry the coin acceptor thoroughly by using filtered compressed air to blow it dry.

NOTE: The reason we recommend using boiling water is that it evaporates faster than cold water and speeds drying time.

GATE OPEN AS SHOWN CLEAN MAGNET BY DRAGGING A SCREWDRIVER BLADE ACROSS SURFACE

Figure 7-2 Cleaning the metal coin acceptor

  • To lubricate the coin acceptor: 0 Use ONLY powdered graphite and put it ONLY on the moving parts of the coin acceptor. These parts are called out in Figure 7-3. O Be extremely careful to keep the powdered graphite away from paths that are traveled by the coins.
  • WARNING — DO NOT USE OIL TO LUBRICATE THE COIN ACCEPTOR.
  • Check the coin chute for obstructions such as: paper, gum, etc.
  • Reinstall the coin acceptor to the coin door. See Figure 7-1. O Place the two pegs at the coin acceptor’s base into their retaining slots. 0 Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches.
  • Close and lock the coin door.

APPLY POWDERED GRAPHITE HERE

CRADLE

Figure 7-3 Lubricating the metal coin acceptor

Page 50

SQUEEZE PINS TOGETHER TO UNLOCK

HOLDING BOTH GATES TOGETHER, PUSH UP AND PULL OUT

Figure 7-4 Opening the plastic coin acceptor

PLASTIC COIN ACCEPTOR MECHANISMS

The plastic coin acceptor mechanism(s) must be removed periodically from the coin door and cleaned.

  • Make sure the power to the game is off.
  • Untock and open the coin door.
  • Remove the coin acceptor mechanism(s) as shown in Figure 7-1. © Push down on the two spring loaded latches. O While holding the latches down, pull the top of the acceptor mechanism toward you. D Release the latches and lift out the mechanism
  • Squeeze the two pins indicated in Figure 7-4 together to open the mechanism and break it down into its three basic parts. O Clean the mechanism in hot soapy water. It never rusts. O Rinse the mechanism in clean hot water and allow it to dry.

7-3 O Reassemble the mechanism (it never needs lubrication).

  • Check the coin chute for obstructions such as: paper, gum, etc.
  • Reinstall the coin acceptor to the coin door. See Figure 7-5. O Place the two pegs at the coin acceptor’s base into their retaining slots O Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches.
  • Close and lock the coin door.
NOTE: See Figure 7-6 for instructions on how to. set the plastic coin acceptor mechanisms to either accept or reject Canadian quarters.
Page 51

ACCEPTOR CAN BE SET TO ACCEPT U.S. QUARTERS ONLY OR BOTH U.S. AND CANADIAN QUARTERS.

SS

SLIDE MAGNET TO EXTREME RIGHT (AS SHOWN) TO ACCEPT BOTH U.S. AND CANADIAN QUARTERS.

SaaS!

TO ACCEPT U.S. QUARTERS ONLY, SLIDE MAGNET TO EXTREME LEFT.

Figure 7-5 Changing the plastic coin acceptor to accept American or Canadian quarters.

7-4

Page 52

jenuep] AOyUOP ‘ALIA NOA ANVHL iINOA d13H OL AGV4aY GNVLS SHOLNGIHLSIG HNO GNV 44VLS HNO “SHAdWd SANVD YNOA HLIM G30IAOu’d HSEWNN 33u4 TIOL SHL LV ANVdWOO ONIYNLOVANNVW AVMGIW YO YOLNEIYLSIG YNOA LOVLNOOD 3SV31d ‘SNOILSAND SAVH TULS GNV NOILOZS SIHL HDNOYHL GV4Y NOA Jl “HOLINOW ‘AL SAWV5D YIBHL ONIYIWdSY ONV ONILOOHSAIENOUL NI FAYDAG SOINOYLOS13 NV LNOHLIM SSOHL CIV OL GS0NALNI SI GNV YANNVW GNVLSYHSGNN OL ASV3 NV NI G10 SI NOILOSS SIHL NI GANIVLNOO NOILVWHOSNI SHL ‘S.LON ASV31d

Page 53

Color T.V.

Color T.V Monitor

Introduction: (How to use this section of your manual.)

This section has been designed to simply familiarize you with one of the more mystical components in your game — the T.V. monitor. If you are an electronics technician who is quite knowledgeable on the subject, you may decide to just go to the schematics and start troubleshooting the defective monitor. But if you are like most people, a monitor is a T.V. set, and that means a complex doo-dad that means big buck repairs. This isn’t necessarily so. This section of the manual will acquaint you with the monitor and could just help you repair it if you feel adventurous enough to give it a try. If you have any knowledge of electronics, especially the use of a voltmeter, the repairs you can make are astonishing. Just keep in mind that ELECTRICITY CAN BE VERY DANGEROUS, SO BE CAREFUL!

If you want to understand how a monitor works, just read the “THEORY OF OPERATION" subsection. If you wish, you can follow along with the schematics. The information is presented in a very basic manner but more complete treatment of the subject can be found in the technical sections of bookstores.

If you want to attempt to repair your monitor, it would be a good idea to read this whole section beginning to end before starting. Pay attention to all warnings

8-1 and take them seriously. The more equipment you have the better, but a low cost Volt-Ohm-Milliameter can often, do the trick. Here are the steps to take:

  • Find the symptom that matches the problems your monitor has in the “SYSTEM — DIAG- NOSIS” subsection. The diagnosis tells the circuit or area the problem may be in and possibly even the actual component causing it.
  • Once you have the circuit that is causing the trouble, read the “TROUBLESHOOTING” subsection to learn the procedure for finding the bad part.
  • Next, go to the schematic section and find the schematic that matches your monitor. It may be helpful to read the “DIFFERENCES BETWEEN MONITORS" subsection if you are unsure of which monitor you have. Use the schematic to see what parts are in the offending circuit.

That really is all there is to it. Just remember that there are some bizarre or rare symptoms not covered, or that a monitor may have two or more different problems that only a genius, the experienced, or an experienced genius can figure out. But be patient, follow safety precautions, and remember that there is also literature available from the monitor companies through your distributor or from Midway Manufacturing Company on request. (There is a toll free number on the back side of the front cover of this manual.)

Page 54

Symptom Diagnosis

. Insufficient width or heighth: A. Horizontal line (due to VERTICAL CIR- CUIT DEFECT). O Bad yoke. O Bad vertical output section. O Open fusible resistor in vertical section. O Bad height control. 0 Bad flyback. B. Vertical line (due to HORIZONTAL CIR- CUIT DEFECT). 0 Bad yoke. O Open width coil. O Open part in horizontal output section. . Picture spread out too far or crushed in certain areas: A. Horizontal or vertical output transistor. B. Bad component in output circuitry. . Line too close with black spacing: A. Problem in vertical section causing poor linearity. . Poor focus and convergence: A. Bad high voltage transformer (“flyback”) or control. B. Focus voltage wire not connected to neckboard terminal. . Colors missing; check: Interface color transistors. Color output transistors. Cracked printed circuit board. Color circuits. . Video input jack. . Picture not bright enough: A. Weak emission from picture tube. (Turn horizontal sync off frequency and put brightness all the way up for about 15 minutes. Occasionally this cures the problem.) moow>

. Silvery effect in white areas; check: A. Beam current transistors. B. Weak picture tube emission. . Too much brightness with retrace lines; check: A. Beam limiter transistors. B. Brightness and/or color blanking controi set too high. Increasing brightness causes an increase in size and poor focus. A. Weak high voltage rectifier or regulation (high voltage unit).

8-2 10.

11.

12,

13.

14,

15.

16.

17.

18.

19.

20. Smail picture and/or poor focus: A. Low B+ voltage (power supply trouble).

Vertical rolling: A. Vertical oscillator transistor, IC, or circuit. B. No sync from logic board.

Horizontal line across center: A. Vertical output circuit is dead (see symptom No. 1. A.). B. Vertical oscillator is not putting out the right wave form. Picture bends: A. Horizontal sync needs adjusting. B. Magnetic or electromagnetic interference.

Flashing picture, visable retrace lines: A. Broken neck board. B. Internal short circuit in the picture tube (arcing). Unsymmetrical picture or sides of picture: A. Defective yoke.

No brightness, power supply operating — No high voltage for the picture tube; check: A. Horizontal oscillator. B. Horizontal amplifier and output. C. Flyback transformer (high voltage unit).

No brightness, high voltage present; check: Heater voltage to the tube at the neck board. Screen-grid voltage for the tube. Focus voltage. Grid to cathode picture tube bias. >

lo high voltage; check: For AC input to the “flyback”. Horizontal deflection stages. Flyback transformer. Yoke. Power supply. moom>rz FOB

No horizontal and vertical hold; check: A. Sync transistors and circuit. B. Wires and jack from logic board to the monitor. Wavey picture — (power supply defect); check: A. Transistors, diodes, electrolytic capacitors in the power supply.

Page 55

21.

22.

23. Moving bars in picture: A. Ground connector off between monitor and logic boards. B. Defect in the power supply (see wavy picture symptom).

Washed out picture (see picture not bright enough): A. Check video signal at the cathode pins with an oscilloscope. If there is about 80 volts peak to peak, the picture tube has weak emission.

Monitor won't turn on: A. Problem in the power supply: Check fuse, transistors, open fusible resistor.

B. Shorted horizontal output transistor. C. Defective high voltage disabling circuit. D. Crack(s) somewhere on main chassis board.

24, Can't adjust purity or convergence:

A. Use a degausser to demagnetize the picture tube carefully following your degausser’s instructions. B. Picture tube defective. C. Metal foreign material is in picture tube shield. D. Nearby equipment is electromagnetically interferring. E. The poles of the earth are pulling off the purity. F. Poor focus or width of picture.

Guide To Schematic Symbols

THERMISTOR (POLARITY DOESN'T MATTER)

SVT

INDUCTOR, COIL, CHOKE (POLARITY DOESN'T MATTER)

(-) CATHODE

(+) ANODE

ZENER DIODE IRON CORE TRANSFORMER (SUCH AS A FLYBACK)

VL

FUSE (POLARITY DOESN'T MATTER)

CATHODE (-)

ANODE (+)

DIODE

Page 56

COLLECTOR Ko a COLLECTOR BASE ———> BASE EMITTER xe EMITTER mS

NPN TRANSISTOR PNP TRANSISTOR

WM

VARIABLE RESISTOR, POT, CONTROL RESISTOR (POLARITY DOESN'T MATTER) (POLARITY DOESN'T MATTER)

+

LINES ARE CONNECTED ELECTROLYTIC CAPACITOR

LINES ARE NOT CONNECTED CAPACITOR (POLARITY DOESN'T MATTER)

hg = GROUND

Page 57

Troubleshooting

Troubleshooting monitors requires experience, patience, and luck. The first step is to match the symptom the monitor displays to the diagnosis next to it in the “SYMPTOM-DIAGNOSIS” subsection. This will pinpoint the circuit the problem is probably in, and often the parts to check. Next, the circuit should be visually inspected to see if there are any parts broken, burned, or if something is there that shouldn't be, like a loose screw, etc. Some parts go bad before others and should be checked first. In fact, following is the general order in which parts usually go bad:

  • Semiconductors (like transistors, diodes, and integrated circuits). Fusible resistors. Electrolytic capacitors. Resistors. Capacitors and coils. Always remember that a monitor can bite like a snake. Even when it is turned off, capacitors hold voltage and will discharge it to you should you be touching chassis ground. The picture tube or CRT, itself, is a giant capacitor, so avoid the flyback anode plug hole. With the monitor on, the power supply circuit and/or the flyback, which puts out at least 18,000 volts, CAN BE KILLERS! Avoid handling power transistors (usually output transistors), yoke terminals, and other high power components when the monitor is on.
WARNING: That picture tube is a bomb! When it breaks, first it implodes, then it explodes. Large pieces of glass have been known to fly in excess of 20 feet in all directions. DO NOT carry it by the long, thin neck. Discharge its voltage to ground by shorting the anode hole to ground. Use a plastic handled screwdriver, connect one end of a wire with an alligator clip at each end to chassis ground and the other end to the metal shaft of the screwdriver. Using ONE HAND ONLY (put the other in your pocket) and touching ONLY the plastic handle of the screwdriver (DO NOT TOUCH THE METAL SHAFT) stick the blade of the screwdriver into the anode hole. Be prepared for a fairly loud pop and a flash. The longer the monitor has been turned off, the smaller the pop and dimmer the flash. But BE CARE- FUL, picture tubes will hold a very ARON healthy charge for at least a week if not longer. Even after you've discharged it once, it may still carry a residual charge. It's better to be too careful than dead, which is why electronic equipment always carries stickers referring servicing to qualified personnel. Handle the side with the viewing screen against your chest when changing it. ALWAYS wear safety goggles when handling the picture tube.

To maintain the safety and performance of the monitor, always use exact replacement parts. For instance, the wrong components in the power supply can cause a fire, or the wrong color transistor may give a funny color to the picture. Service your monitor on a nonconductive firm table like wood, NOT METAL, and take off all of your jewelry just in case. With all this in mind, you are ready to begin troubleshooting.

Observe the picture carefully. Try to vary the appropriate control that would most likely affect your particular symptom. For example, if there is poor brightness or no picture, try turning up the brightness or contrast control. If the controls have no effect at all, chances are there is trouble with the control itself, the circuit it controls, or a nearby circuit that may be upsetting voltages. Go to the list of symptoms and determine with the schematic where the bad circuit is.

CAUTION:

Keep in mind that capacitors hold a charge as can the picture tube (for at least a week and usually longer), and could shock you.

First, check for obvious visual defects such as broken or frayed wires, solder where it is not supposed to be, missing components, burned components, or cracked printed circuit boards. If everything looks good up to this point, make sure that diodes, electrolytic capacitors, and transistors have their leads connected in the right polarity as shown on the schematic and the circuit board. Turn on the power and measure the voltages at the leads of the active devices such as tubes, transistors, or integrated circuits. Any voltage that does not come within at least 10% to 15% of the voltage specified on the schematic indicates either a problem with that device or a component connected with it in the circuit. The next step is to use the ohmmeter to narrow down the field of possible offenders.

Page 58

To test a transistor, one lead of the ohmmeter is placed on the base; and the other lead placed just on the emitter, then on the collector. A normal transistor will read either high resistance (infinite), or little resistance (400 to 900 ohms), depending on the polarity of this type transistor. Then the leads should be switched, one remaining on the base, and the other switched from the emitter to the collector. Now the opposite condition should result: the resistance should be infinite if it was lower when the other lead was on the base. Consistantly infinite readings indicate an open, anda short is demonstrated by 0-30 ohms on most of these test readings. Finally, place one lead on the collector, then the other on the emitter. No matter which lead is used, there should be infinite resistance. Any lower reading, such as 50 ohms (which is typical on a bad transistor), indicates a short. This all sounds pretty confusing, but a little experience on a good transistor will make you an expert in no time. Usually, the lowest ohmmeter setting is used for testing transistors. Once in a great while a transistor may check out good on this test, but may actually be “leaky” or break down only on higher voltages. If in doubt, change it. It is also wise to check the transistor out of the circuit just in case some component in the circuit is affecting the ohmmeter reading. A diode is tested like a transistor except it only has two leads. Again, there should be high resistance one way and little resistance the other. If it tests bad, take one lead out of the circuit in case some component is messing up the ohmmeter reading.

NOTE: DO NOT leave soldering equipment on the leads too long since all semiconductors, especially integrated circuits, are easily destroyed by heat.

Without special equipment, integrated circuits are checked by verifying the proper DC voltage on the pins and the correct AC wave form using an oscilliscope. BE CAREFUL: Shorting their pins can easily destroy them. Resistors are checked with an ohmeter and should usually be within ten percent of the value stated on them and on the schematic. You may have to desolder one lead from the printed circuit board. If you wreck the foil on the board, carefully solder a small wire over the break to reconnect the conductive foil. Capacitors are tricky. Their resistance goes up when checked with an ohmmeter which shows a charging action. As they suck up current from the meter, the voltage goes up and so does the resistance. If you are sure a particular circuit is giving you a problem and everything else checks out O.K., Electrolytic capacitors are prime suspects. Substitute a new one and keep your fingers crossed.

Theory of Operation

To understand what goes on inside the monitor, large general groups of circuits will be examined instead of laboriously analyzing the branches and small circuits that make up these groups. This will help avoid confusion and aid in a basic, concrete, knowledge of what makes up a monitor.

THE POWER SUPPLY — The AC going to the monitor from the game transformer is just like the voltage and current from your wall outlet. It jumps up and down going positive and negative sixty times a second. But a monitor needs nice, smooth DC; direct current, not alternating. So diodes chop up the AC and a big electrolytic capacitor filters it out to make it even smoother. Since the monitor is a big piece of electronic equipment, with many circuits demanding a lot of power from the power supply, there are also zener diodes and transistors to help maintain a nice, constant, smooth voltage so that the monitor circuits don’t jump around. And this is what happens when you see a wavy picture. There is AC creeping through the power supply, so it must be malfunctioning. If the voltage from the power supply is too low, the other circuits will be starved for power and you may see a small, wavy picture, or none atall. Some circuits receive voltages that are higher than what the power supply should put out. But they come from the flyback transformer which will be discussed later.

THE INTERFACE SECTION OF THE CHASSIS — The interface section of the chassis is fairly easy to identify. It is right by the place where the video jack(s) from the logic board(s) plug into. There are sets of transistors that receive the separate red, green, blue, and sync information from the cables that come from the logic boards. The circuits jack up the voltage and match impedances, or in other words, prepare the logic board outputs for the circuits that will really amplify them for the output devices such as the yoke in the case of the sync, or the picture tube that shows the colors.

Page 59

An interesting aside is that our sync is composite negative sync. That means two things:

  • The sync is a negative going wave form.
  • There are two pulses going at different speeds over the same wire: a. Vertical wave forms at 60 times per second (or Hertz) and b. Horizontal wave forms at about 15,750 times per second (Hz). The sync is amplified by a sync amplifier transistor and sent on its way to the oscillators. The sync or timing information will be explained along with the oscillator shortly. The color information is sent via wires to the neck board where the main amplification occurs. This will also be discussed later.

VERTICAL AND HORIZONTAL DEFLECTION— After the sync signal is amplified by the sync amp, it goes to two different sections, the vertical and horizontal circuits. Basically, the sync signals are for timing so the picture doesn't mess up since it is assembled like an orderly jigsaw puzzle, but so fast that you can’t see the electron beams for each color painting the picture on the screen. This will all become clear soon. For now, we will follow the 60 cycle component of the sync as it goes on its journey to the deflection yoke. The 60 cycle pulse goes to the vertical oscillator to make sure this circuit goes back and forth (or oscillates) at 60 times a second. Without this pulse keeping the circuit at the correct speed, it may get lazy and oscillate at 58 cycles or lower, or get ambitious and oscillate at 62 cycles or higher. At the wrong speed, the picture will start to roll up or down. A Wells Gardner 13” (K4806) or 19” (K4906, K4956) color monitor uses an integrated circuit for its sync section. An Electrohome 13” or 19” color monitor uses an integrated circuit 1C501 for its sync section. Wells Gardner uses HA11423 and Electrohome uses HA11244. These ARE NOT interchangeable! The idea is all the same. The output to the vertical amplifying transistors for all monitors must form a sawtooth wave form, sort of like a bunch of pyramids, racing through the yoke's vertical coils at 60 times a second. Along the way to the output transistors, the 60 cycle pulse is shaped and amplified to do the job: the yoke magnetically pushes the electron beam to fill the screen out sideways looking at the screen with the greatest length going up and down. Or viewing the screen sitting like a home television set, the amplified vertical output fills the screen up and down. Watching a monitor like this, seeing only a horizontal line means a problem with the vertical coils of the yoke or anything from the vertical output section on back to the oscillator.

8-7 The horizontal section is very similar with a few exceptions. The horizontal wave shape is more like a square and has a frequency of 15,750 cycles a second. Both Wells Gardner and Electrohome use the other side of their respective integrated circuits for the horizontal circuitry. If the oscillator isn’t going at the correct speed, the picture may move sideways, start to slant, or tear up with slanted thin figures. With both the vertical and horizontal of all monitors, there are variable resistors that change the speed of the oscillators up and down. This way you have controls that can make the correct frequencies to keep the electronic jigsaw puzzle nicely locked in place. If you're driving in acar and next to you someone else is driving their car at exactly the same speed, it will appear that they are not moving. And this is why the sync frequency and the oscillator’s frequency must match, so the picture doesn’t appear to move. The correct wave form is shaped and amplified in the circuitry just like in the vertical section. But the horizontal output transistor is a large power transistor and not only serves to give current to the horizontal yoke windings, it also feeds the flyback transformer.

THE FLYBACK TRANSFORMER (OR HIGH VOLTAGE UNIT) — The picture tube needs high voltage to light up, and the power supply can’t meet this demand. The flyoack transformer receives current alternating at about 15,750 times per second from the horizontal output transistor. The “flyback” jacks up its input voltage and puts out a higher voltage alternating at the same speed. But, in your “flyback” there are diodes that chop up the alternating voltage to make it a smooth DC output just like in the power supply. This is what goes through that thick red wire to your picture tube. THIS AREA HAS ABOUT 18,000 VOLTS ON IT AND IT CAN KILL YOU!

The “flyback” may be dangerous, but it is also generous. It has extra output windings which give voltage to the heater pins of the picture tube, voltage for the vertical deflection circuits, and picture tube screen-grid voltage. So in a way, the high voltage “flyback” is like a second power supply.

COLOR CIRCUITS — The color circuits are pretty straight forward. The signals go into the interface section where some amplification and impedance matching occurs. These circuits are pretty sparse and simple. Each color just has two transistors and a diode with some resistors and capacitors. From here, the AC color signal is sent by wires to the neck board. The color output circuits are on the neck board. The color signals going to the transistors are controlled by two variable resistors called drive controls. There are only two, one for the red and one for the green.

Page 60

The blue doesn’t have one. In the emitter part of each transistor is another variable resistor that is the cut off control. These controls vary the amount of amplified AC signal that goes to the cathodes of the picture tube. The more signal, the more color. The bases of each of these transistors are connected together and are all connected to the blanking and beam limiting transistors which are in the interface section. The beam limiter helps control the brightness level, and the blanking transistor rapidly turns the picture tube on and off so that retrace lines don’t show up on the screen. By turning up the brightness on a good monitor, these four to six retrace lines can be seen slanting diagonally across the picture.

PROTECTION CIRCUIT —

Te protect the high voltage section against voltages that are too high coming from the power supply which could cause X-rays to be emitted from the “flyback”, a circuit senses the higher power supply voltage, and using a transistor, turns off the horizontal oscillator. Since the horizontal oscillator doesn't work, the horizontal output transistor has nothing to feed the “flyback” which in turn has nothing to feed the picture tube. The monitor will be silent, have no picture, and will appear to be off. But don’t be fooled. There is still that excessive amount of voltage coming from the power supply. To find out, check at pin two of Wells Gardner's 1C501 and emitter of X04 for the Electrohome monitor. Here are the voltages you should receive:

Wells Gardner Electrohome 130VDC 120VDC The best place to measure this voltage on an Electrohome monitor is at a pin marked B1 on the chassis. This is because a 13 inch color Electrohome monitor, The GO07-FBO or G07-902, has an integrated circuit and very little else in the power supply. Still, there should be 120VDC at B1.

THE PICTURE TUBE (OR CRT) — The picture tube or CRT is an output device. In other words, the end result of the circuit's work is displayed by this part. Actually, the output of other circuits is in the neck of the picture tube. First, there is the heater. The heater boils off electrons from the cathodes so that they (the electrons) shoot up to the screen to excite the phosphors so that the three phosphors emit three colors of light. The cathodes are next, and again they emit electrons to turn on the tube phosphors, making it glow. The cathode can arc or short to the heater resulting in no picture and a defective picture tube. Next come the grids. The first grid is grounded. The following grid is the screen grid which receives about 300VDC depending on the brightness setting. The next grid closest to the picture tube screen is the focus grid which gets about one fifth the amount of voltage that is applied to the picture tube anode.

After jetting from the cathode through all these grids, the electrons speed through a mask, a sheet of material with tiny holes, and then excite the tiny dots of phosphor in the inside surface of the picture tube screen. The green electron gun (or cathode and circuitry) spits out electrons which head for the green phosphors only. The same goes for the red and blue guns. The way the phosphor light blends determines the color seen. Should these electron beams become too intense, they may burn the phosphor. With the monitor off, this can be seen as a dark permanent image of the video information on the tube screen.

Differences Between Monitors

The easiest way to identify the brand of monitor you are working with, assuming you can't find the brand name written on it anywhere, is to check the color of the suction cup type insulator that houses that dangerous anode plug on the CRT. Both monitors use a red wire but the Wells Gardner anode cup is BLACK while the Electrohome anode cup is LIGHT GRAY. Unfortunately, “call-out-numbers” for parts, circuit layout, and even circuit design are similar enough to confuse the average observer. Let’s say you have an Electrohome that isn’t working. No problem. You can scavenge parts from an old broken up one that you may have around.

Now let's say you have a Wells Gardner that isn’t working. STOP! This could be a problem. There are 3 different types of Wells Gardner K4900 SERIES monitors in the games. Here are ways to identify them. K4906 (1st TYPE) — This monitor's identifying tags have BLACK ink printed on a white background. There is NO Vertical Damping Control. (This Control would be next to the Vertical Hold Control but this area is jumpered with a small wire instead. K4906 (2nd TYPE) — This monitor's identifying tags have RED ink printed on a white background. There IS a Vertical Damping Control next to the Vertical Hold Control. The Damping Control provides a few more lines on the top of the monitor screen (monitor viewed as a normal T.V. would be) for any video game that may need these lines to fit the picture on the

Page 61

screen. Moving the Control may distort the top part of your picture (or the side, depending on the game and how the monitor is mounted) so go ahead and move it if you are having this type of problem. To accommodate this new feature, there are a few circuit changes. ONE MAJOR DIFFERENCE BETWEEN THESE TWO VERSIONS OF THE K4906 IS THE YOKE. They look the same but notice the part numbers: K4906 WITHOUT the Damper Control: 2021111201 K4906 WITH the Damper Control: 2021111258 Since the companies like to change part numbers at the drop of a hat, the best thing to do is to request whatever part number is written on your yoke. If you should get the wrong yoke, the results will be: Picture distortion. Excessive brightness. Too much or too little vertical picture size. K4956 (3rd TYPE) — This monitor is identical to the K4906 WITHOUT the Damper Control EXCEPT the picture tube is vertically mounted and there is an additional small P.C. Board mounted on the monitor where the yoke plugs in. This monitor is used on some Cocktail Table games where the picture has to flip for the second player. Generally speaking, some games flip the picture image via the logic board programming but this monitor is used in games that flip the picture image via generation of a small signal voltage which is sent to the extra P.C. Board on this monitor. This signal voltage causes relays on this extra P.C. Board to flip the picture by reversing the horizontal and vertical signals to the yoke pins. What kind of problems can this extra P.C. Board cause? If the relays become defective, the picture won't flip. If the P.C. Board gets cracked you may have a horizontal line on the screen, a vertical line on the screen, or maybe just a dot in the center of the screen. Of course, the logic board could be defective and not sending the signal to flip the picture. In any case, some people feel that using relays is cheaper, simpler, and more reliable, so this is an advantage.

CONTROLS YOU MAY NOT TOUCH Basically, on the Electrohome monitor, you can move any control you want EXCEPT for the B1 control. This sets the power supply voltage (ideally at 120 VDC) and is located right behind VERTICAL HOLD. The 13” Electrohome DOES NOT have this control. It may also be wise not to move the VERTICAL LIN- EARITY since this distorts the picture and is hard to reset perfectly. If you do move it, turn on the Cross Hatch Test Pattern of your game and try to get the squares to the point where they are equal in size by readjusting this Linearity Control.

On the Wells Gardner monitor, brightness is adjusted by the “BLACK LEVEL” Control which is right next to the Horizontal Frequency Control. Under the Focus Control is the “SCREEN” Control which youDO NOT touch. Yes, this control does adjust the brightness, but it is used to set the CRT bias and is adjusted at the factory. When Wells Gardner sets it, they mark the position with a black mark on the knob. If you move it, be sure to realign the mark and THEN set the BLACK LEVEL Control to the brightness you desire. So, other than the SCREEN control, you may adjust any of the controls.

Parts Interchangeability

Some parts can be interchanged on all of the monitors. Here are the rules:

  • You CAN swap any resistor between monitors that has the same resistance, wattage rating, and tolerance. You CAN swap any capacitor between monitors that has the same capacitance and voltage rating. You CAN swap many of the parts between the 19" and the 13” versions of each manufacturer's monitor. BUT, be certain to compare the manufacturers’ part numbers to be positive the parts you want to interchange are identical. BE SURE you have read the section DIFFERENCES BE- TWEEN MONITORS which was covered earlier. You CANNOT swap any picture tubes between monitors!! In the past you could, but Wells Gardner is now using a new monitor. When ordering a replacement picture tube, ALWAYS SPECIFY THE PICTURE TUBE NUMBER! You CANNOT change any part that is a safety part, one that is shaded in gray on the schematic; it MUST be IDENTICAL to the original. To do otherwise IS DANGEROUS. For instance, the 13 inch Electrohome (G07-902) monitor “flyback” looks identical to the 19 inch Electrohome (G07- 904) monitor “flyback”. In fact, there is even a 19 inch Electrohome (G07-905) monitor (which is an obsolete model) with a similar looking “flyback”. NONE OF THESE ARE INTER- CHANGEABLE! You CAN change any of the parts between the G07-904 and G07-907. They're essentially the same monitor except that the G07-907 has a vertically mounted picture tube. If there is any doubt about what parts can be swapped between each manufacturer's 19 inch and 13 inch models, compare the manufacturer's part number between each one. If they match up, they are the same part.
Page 62

Power Supply Voltage and Symbols

symbol | Voltage Operating Circuit ® 15V | Vert. Osc. Sync Blanking | | CRT Cut-olt 1

+ 1 a | 130V. | Horiz. Osc. | Horz. Drive | Horz, Output | Vert. Output \

  • 175V Video Output

351 COLLECTOR

AVIDIV 200uSEC/DIV 20VIDIV 10uSECIDIV

TP.31 DC COUPLED 94023 BOTTOM LINE=0 VDC

2VIDIV 200MSECIDIV SVIDIV 20uSECIDIV

LC. 301, PIN 3 F

Macarena nn

mmm

1VIDIV SMSECIDIV 1V/DIV 20u SECIDIV

‘TP-31, AC COUPLED

1VIDIV 200uSECIDIV 20vIDIV SMSECIDIV

Teo S0) PINGS: NEGATIVE SIDE OF C303

2VIDIV SMSECIDIV 1VDIV 200uSECIDIV O.5/DIV SMSEC/DIV

O.5IDIV 204

1.C. 301,

2VIDIV 10uSECIDIV

F

1VDIV 2MSECIDIV 19” COLOR MONITGR SCHEMATIC DIAGRAM

MODELS 19K4901, 19K4906, 19K4951, 19K4956

ERVICE TECHNICIAN WARNING .

THIS PRODUCT CONTAINS CRITICAL ELECTRICAL AND MECHANICAL PARTS ESSENTIAL FOR X-RAY RADIATION

ONLY TYPE PARTS SHOWN IN THE

CAUTION: FOR CONTINUED SAFETY, REPLACE SAFETY CRITICAL COM. PONENTS ONLY WITH MANUFAC- TUREA’S RECOMMENDED PARTS. POUR MAINTENIR GRE DE SECURITE DE L’APPAREIL. NE REMPLACER LES COMPOSANTS DONT LE FONCTIONNEMENT EST CRITIQUE POUR LA SECURITE QUE PAR DES PIECES RECOMMANDEES PAR LE FABRICANT.

T9301” SYNC. AME 1u SECIDIV lesciaisy/o | zscsas PIN 15 €

sr? cas 180. (7800 ‘oor fi" St pe hekow SCo45 |

HOR. DRIVE oe Py oy] Bt z6I08K Srey ins6o

SYNC AMP VvOSC H.0SC Haria23

DEgAUSSING COIL RED ‘Our, Green out OSCILLOSCOPE WAVEFORM PATTERN The waveforms shown are as observed on the wide band oscilloscope with the monitor turned to a reasonably strong signal and a normal picture. The voltages shown on each waveform are the approximate peak amplitudes. If the waveforms are observed on the oscilloscope with @ poor high frequency response, the corner of the pulses will tend to be more rounded than those shown and the amplitude of any high frequency pulse will tend to be less.

62 Sur 2SC2068.8/.BeK 25C2068L.B/.BBK 28C2068L 8/L.88K( 28cSI@Bve/eve 2SCISISSvERVC 2ScISaave/cve (ee aa ae t FAS 2) nso} =a wn,

27atRcv] armine2) nf

) asc2073 pote eer) © (SHIFT) 108 RIGHT poncevems S86) nes HY. UNIT | case a2. 7382 | [mowsize C703 1000P7800v

K4901D, K4906D, K4951D 5833 K4956B 8-10

Page 63

REPLACEMENT PARTS LIST This monitor contains circuits and components included specifically for safety purposes. For continued protection no changes should be made to the original design, and components shown in shaded areas of schematic, or A*® on parts list should be replaced with exact factory replacement parts. The use of substitute parts may create a shock, fire, radiation or other hazard. Service should be performed by qualified personnel only.

MAIN BOARD

Ref. No.Part No.DescriptionRef. No.Part No.Description

RESISTORS RESISTORS (CONT.)

R201203X6500-6451K Ohm, 5%, 1/4W CarbonR369203X5602-329680K Ohm, 5%, 1/2W Comp.
R202203X6500-52330 Ohm, 5%, 1/4W CarbonR370203X6501-90233K Ohm, 5%, 1/4W Carbon
R203203X6500-405100 Ohm, 5%, 1/4W CarbonR371203X9014-5841K Ohm, 5%, 1W Metal Oxide
R204203X6700-327100 Ohm, 5%, 1/2W CarbonR372203x9101-11912K Ohm, 54%, 1W Metal Oxide
R205203X6700-421270 Ohm, 5%, 1/2W CarbonR375203X6700-763,6.8K Ohm, 5%, 1/2W Carbon
R206203X6500-540390 Ohm, 5%, 1/4W CarbonR376203X9104-404270 Ohm, 5%, 2W Metal Oxide
R207940X2201-934200 Ohm, 5%, 1/4W CarbonR377203X6500-447150 Ohm, 5%, 1/4W Carbon
F208203X6500-540390 Ohm, 5%, 1/4W CarbonR378203X6500-88610K Ohm, 5%, 1/4W Carbon
R209340X2201-934200 Ohm, 5%, s/4W CarbonR379203X6500-88610K Ohm, 5%, 1/4W Carbon
R210203X6500-540380 Ohm, 5%, 1/4W EarbonR380203X6500-8658.2K Ohm, 5%, 1/4W Carbon
Roi340x2201-934200 Ohm, 5%, 1/4W CarbonR38203X6500-7242.2K Ohm, 5%, 1W Metal Oxide
R214203x6500-6451K Ohm, 5%, 1/4W CarbonR383203x9014-387150 Ohm, 5%, 1W Metal Oxide
F216203X6501-126100K Ohm, 5%, 1/4W CarbonR502203X6500-88610K Ohm, 5%, 1/4W Carbon
R216203X6500-6451K Ohm, 5%, 1/4W CaronR503204X 1700-535,150 Ohm, 5%, 15W Metal Oxide
R217203X6500-405100 Ohm, 5%, 1/4W CarbonR504203X9014-26747 Ohm, 5%, 1W Metal Oxide
R218203x6500-6451K Ohm, 8%, 1/4W CarbonR505203X6501-2092.2K Ohm, 5%, 1i4W Carbon
R219203X6501-126400K Ohm, 5%, 1/4W CarbonR506,203X9104-10515 Ohm, 5%, 2W Metal Oxide
R220203X6500-6451K Ohm, 5%, 1/4W CarbonR507203X5602-185330K Ohm, 5%, 1/2W Comp.
R221203X6500-405100 Ohm, 5%, 1:4W CarbonAkeREO1204X1625.0583.3 Ohm, 5%, 10W WW
R222203X6500-7623.3 Ohm, 5%, 1/4W CarbonR701203X9105-1412.2 Ohm, 5%, 2W Metal Oxide
R224203X6500-16910 Ohm, 5%, 1/4W CarbonR702203X6206-4412.2 Ohm, 5%, 1/2W Carbon
R225203X6500-16910 Ohm, 5%, 1/4W CarbonR201204X2070.0722K Ohm-B Semi-Fixed
R226203X6500-16910 Ohm, 5%, 1/4W CarbonR301204X2070-0845K Ohm-B Semi-Fixed
R227203X6501.04447K Ohm, 5%, 1/4W CarbonVR303204X2070.055500 Ohm-B Semi-Fixed
R228203X6500-6451K Ohm, 5%, 1/4W CarbonVR351204X2070-0722K Ohm-B Semi-Fixed
R229203X6700-421270 Ohm, 5%, 1/2W CarbonR352204X2070.0722k Ohm-8 Semi-Fixed
R230203X6500-8638.2K Ohm, 5%, 1/2W Comp.
R231203X6500-8638.2K Ohm, 5%, 1/2W Comp.
R232203X6500-8838.2K Ohm, 5%, tien comp.
R233203X6500-468180 Ohm, 5%, 1/4W Carbon
234340X2820-93482 Ohm, 5%, 1/4W CarbonCAPACITORS
R235340X2820-93482 Ohm, 5%, 1/4W Carbon201203X0014-088.1000 uF, 16V, Electrolytic
R236340X2820.93482 Ohm, 5%, 1/4W CarbonC202202X7200-064330 pF, 500V, Ceramic
R301203X6500-508270 Ohm,5%, 1/4W CarbonC203202X7200.043220 pF. 500V; Ceramic
R302203X6500-8638.2K Ohm, 5%, 1/4W CarbonC204202X7200-043220 pF, 500V, Ceramic
R303203X6500-8638.2K Ohm, 5%, 1/4W Carbon205203X0014-076470 uF, 16V, Electrolytic
R304203X6500-7242.2K Ohm, 5%, 1/4W CarbonC206203X1810.1490.1 uF, 125V Mylar
R305203X6500-84268K Ohm, 5%, 1!4W CarbonC207349X2232.109(022 uF, 100V Mylar
R306203X6003-2017.5K Ohm, 2%, 1/4W Carbon301203X0014-065,330 uF, SOV Electrolytic
R307203X6500-8255.6K Ohm, 5% , 1/4W CarbonC302203X1600-5630.033 uF, 50V Mylar
A309203X6500-96522K Ohm, 5%, 1/4W CarbonC303203X0629.0373.3 uF, 50V Electrolytic.
R310203X6500-98839K Ohm, 5%, 1/4W CarbonC304203X 1600-3660.068 pF, SOV Mylar
R311203X6500-7623.3K Ohm, 5%, 1/4W CarbonC306203X0412.01222 uF, 16V Tanial
R312203X9014-7414.7K Ohm, 5%, 1/4W Carbon307203X 1600-6340.033 UF, SOV Myiar
R313.204X 1450-5371K Ohm, 5%, SW CarbonC308203X0025-1743.3 uF, 50V Electrolytic
R314203X6500-481220 Ohm, 5%, 1/4W Carbon€309203X 1207-1000.068 uF, 100V PP
R315203X6500-16940 Ohm, 5%, 1/4W CarbonC310203X0629-06110 uF, 100V Electrolytic
R316203X6500-7623.3K Ohm, 5%, 14W CarbonC31203X0041.02540 uF, 180V Electrolytic
R317203X6700-10712 Ohm, 5%, 1/2W Carbon0312202X7050-2484000 pF, 500V Ceramic
R318203X6500-540390 Ohm, 5%, 1/4W Carbon6313203X0040-05247 uF, 160V Electrolytic
R319203X6500-6451k Ohm, 5%, 1/4W CarbonC314203X 1201-2650.033 uF, 200V PP
320203X6501-00233K Ohm, 5%, 1/4W CarbonC315203X0629.0231 uF, 50V Electrolytic
R321203X6501-224270K Ohm, 5%, 1/2W Carton361203X0629-0231 uF, 50V Electrolytic
R322203X6500-88610K Ohm, 5%, 1/4W Carbon352203X0619-045,47 uF, 25V Electrolytic
R351203X6500-88610K Ohm, 5%, 1/4W CarbonC353203x1190-0150.0082 pF, SOV Mylar-PP
R362203X6500-7853.9K Ohm, 5%, 1/4W Carbon0354203X0619-04547 uF, 25V Electrolytic
R353203X6501-08668K Ohm, 5%, 1/4W CarbonC355203X 1600-3660.0068 pF, 50V Mylar
R354203X6500-7623.3K Ohm, 5%, 1/4W CarbonC356202X7050-483.0.01 uF, 500V Ceramic
R355,203X9205-1436.8K Ohm, 5%, 3W Metal Oxide0359202X8065-606100 pF, 500V Ceramic
R358203X5601-87856K Ohm, 5%, 1/2W Carbon360202X7050-3660.0033 pF, 500V Ceramic
R360203X6500-561470 Ohm. 5%, 1/4W CarbonC361202X7050-4830.01 uF, 500V Ceramic
R361203X6500-88610K Ohm, 5%, 1/4W CarbonC362202X7203-032001 UF, 50V Ceramic
R362203X9014-645,1.8K Ohm, 5%, 1W Metal OxideB*C363203X1270-9118700 pF, 1.5 KV PP
WR363204X 1527-7513.9K Ohm, 5%, 7W Metal OxideC365203X1201-2650.33 uF, 200V PP
R364203X6500-24622 Ohm, 5%, 1/4W Carbon6366203X0019-02622 uF, 25V Electrolytic
R365203X6501-00233K Ohm, 5%, 14W CarbonC367202X8065-1626 pF, 500V Ceramic
R367203X6500-88610K Ohm, 5%, 1/4W CarbonC368202X7203-0320.01 uF, 80V Ceramic
R368203X5602-185330K Ohm, 5%, 1/2W Comp.372203X1207-1250.1 uF. 100V PP
Page 64

Ref. No.

0380 4 C501 A 4 C503 4.6504 C505 C506 C507

C703

D203 0204 D205 D206 0208

0305 0501

MAIN BOARD (CONT)

Part No. Description Rat. No. Part No. Description

CAPACITORS (CONT.) SEMICONDUCTORS (CONT)

202X7200-087470 uF, 500V Ceramic2206200x3181-523,Transistor (NPN) 28C1815GR
203X1810-1490.1 uF, 125V Mylar9207200X3181-523Transistor (NPN) 28C1815GR
202X7050-2821500 pF, 500V Cerantic208200X3181-523Transistor (NPN) 28C1815GR
202X7810-2142200 pF, 125V CeramicQ209200X3181-523,Transistor (NPN) 28C1851GR
202X7810-2142200 pF, 125V Ceramic210200X3181-523Transistor (NPN) 2SC1851GR
203X0220-075560 uF, 200V ElectrolyticQ301200X3181-523,Transistor (NPN) 2SC1851GR
203X0040-03422 uF, 160V Electrolytic302200X3207-306Transistor (NPN) 2C2073LBGL2
203X0041.05747 uF, 160V ElectrolyticQ303200X3207-306Transistor (NPN) 2SC2073LBGL2
203X0019-0921000 uF, 25V Electrolytic9351200X3248.217Transistor (NPN) 2SC2482BK
203X0634-06110 uF, 100V Electrolytic352200X4589-802Transistor (NPN) 2SD898B
202X7050-2481000 pF, 500V Ceramican200X2300-033IC HA11423
10501200X2600-183Ic STR381

SEMICONDUCTORS 201X2010-159 Diode, 1S2076-27

201X2010-159Diode, 1S2076-27TRANSFORMERS & COILS
201X2010-159Diode’ 18207627L351201X4710-134Coil, (RF Choke)
201X2010-159Diode’ 182076271352201X5000-083Coil, Horiz. Size
201X2010-159Diode, 1S2076-27tyoreee gtdColl, Adg.
351202X1300-080Transformer, Hor, Drive
201X2010-159Diode, 1S2076-27+
201X2010-159Diode, 1S2076-27Aw1352200%0720-301HV Ualt Melt

201X2010-165, Diode, ISS81 201X2010-189 Diode, 1$2076-27 MISCELLANEOUS

201X2010-159Diode, 182076-27AF501204X7120-073Fuse, 4 Amp. 125V
201X2120-009Diode, RH-IV9402Recep W Wire 3P-M-BG
201X2120-009Diode, RH-IVP201204X9600-466Plug, PWB 3P-J
201X2010-159Diode, 1S2076-27202204X9601-477Plug, PWB 6P-Q
201X3120-216Diode, RM-1AVP4o1204X9600-298Plug, PWB 4P-B
201X3120.216Diode, RM-1AVP501204x9600-249,Plug, PWB 2P-B
201X3120.216Diode, RM-1AVP60t204x9600.304Plug, PWB 4P-C
201X3120-216Diode, RM-1AVTHS01201X0100-112Thermistor

2013120216 Diode, RM-1AV 201X3120.216 Diode, RM-

201x2190-294Diese, RUZVFINAL ASSEMBLY PARTS
201X2120.009Diode, RH-1VA 88X0138-50649VLTP22 Pix Tube
200X3181-523Transistor (NPN) 28C1815GR205X9800-158Lateral/Purity Assembly
200X3181-523Transistor (NPN) 28C1815GRAe 202X1111-201Yoke Deflection
200X4056-260Transistor (PNP) 2SA562-Y-TM204Xx9301-255CRT Socket
200X4056-260Transistor (PNP) 2SA562-Y-TM291X5004-262Automatic Degaussing Coil Unit

200X4056-260 Transistor (PNP) 2SA562-Y-TM

NECK BOARD RESISTORS CAPACITORS

203X6000-729220 Ohm, 5% 1/4W CarbonC401202X7050-2691200 pF, 500V Ceramic
203X6500-540390 Ohm, 5% 1/4W Carbonc402202X7050-2481000 pF, 500V Ceramic
203X6000-661820 Ohm, 5% 1/4W CarbonC403202X7050-2481000 pF, 500V Ceramic
203X6000-729220 Ohm, 5% 1/4W CarbonC404202X7050-2821500 pF, 1.5KV Ceramic
203X6500540990 Ohm, 5% 1/4W CarbonC405202X7050-4830.01 uF, 500V Ceramic

203X6000-661 820 Ohm, 5% 1/4W Carbon 203X6000-729 470 Ohm, 5% 1/4W Carbon 2as3x8000:998 270 Ohm, 5% 1/4W Carbon SEMICONDUCTORS

203X6000-661820 Ohm, 5% 1/4W Carbon401200X3206-800Transistor (NPN) 28C2068LB
203x9104-82415K Ohm, 5% 2W M.O. Formingas02200X3206-800Transistor (NPN) 28C2068LB
203X9104-82415K Ofm, 5% 2W M.O. Forming2403200X3206-800Transistor (NPN) 28C2068LB

203X9104-824 15K Ohm, 5% 2W M.O. Forming 203X6000.998 2.7K Ohm, 5% 1/2W Comp. ANEOU: 203X6000-998 2.7K Ohm, 5% 1/2W Comp.

203X6000-9982.7K Ohm, 5%1/2W Comp.oat oe EthEOUS Wire4P-£
203X9105-1542.2 Ohm, 5% 2W Metal OxiderthreAPS
203X6500-7412.7K Ohm, 5% 1/4W Carbonaoe'204x9600-254Flug; EWE SPA
BoP403204x9600-981Plug, Pin 1P-D
203X6500-7412.7K Ohm, 5% 1/4W CarbonooavoentaePigEWaape
203X6500-74127K Ohm, 5% 1/4W CarbonP7011-020ug,“

204x2115.014 500 Ohm, -B Semi-Fixed 204X2115-014 500 Ohm, -B Semi-Fixed 204x211 15-006 5K Ohm, -B Semi-Fixed 204X2115-006 5K Ohm. -B Semi-Fixed 204X2115-006 5K Ohm, -B Semi-Fixed

Page 65

Alus onetn RED Xi01.XIO3 end 108 VIDEO 2 ¥P. 25: L_xi02.x104 and 106 VIDEO “MP. 25: Xor=xi63 RGB Vi9EO OUTPUT 2sczeu! or S8cisiav . a a ae |

it [x80 BLANKING Hak | ascasac or2écicer x303 x304 —_ [x301,x302,x808,x306. | seen,

Ee | +

X901 POWER DRIVE 25¢2688 ae X 902 ERROR AMP 2SC1890 | | aes

  • _—_—————— -__— Fos, ave |
  • $huoes, ascrase 4 | -— — PER IAT =f Li oS epenen . i — fone = — =

fasce cogs oem oF on 3B

Schematic Notes Uniess otherwise specified Resistance: (92) (KK, M--M&2), 1/4 (W) carbon resistor Capacitance: 1 or higher-» (pF), less than 1-> (yF) working voltage -> 50 (V) $01 f ceramic capacitor oe Lia L Inductance: ( H) | | we BYT cron voKe Electrolytic Cap: Capacitance Value (y F)/working voltage (V), i ive i| T NP - non-polar (or bipolar) electrolytic cap.

riiaaRefer to the parts list for additional component information.

——— ~~ —— 4 2 indicates test point connection

:3301 40MoueerUe Vancar neatenae.;oe
47OI sonay PROTECTOREERO BE, ascesrw gengee orCn asetossaaobindicates chassis ground unless otherwise specifiec

2soaco xe Hz indicates cycles per second AcI20W 6ons/S0H2 210% For satety purposes (and continuing reliability) a replace all components marked with safety syrnoo' with identical type. NO,TE: FR -= fusible resistor ——e—

00-4147-04 Parts identification on circuit boards: G07-CBO e.g. SU1126A (R107 = R1107) $U3030A (R113 = R3113)

Page 66

REPLACEMENT PARTS LIST - ELECTROHOME 19” MONITOR

Components identified by the A symbol in the PARTS LIST and on the Schematic have special characteristics important to safety. DO NOT degrade the safety of the set through improper servicing.

Abbreviations for Resistors and Capacitors

Resistor Capacitor

CR: Carbon ResistorC Cap.: Ceramic Capacitor
Comp. R: Composition ResistorM Cap: Mylar Capacitor
OM R: Oxide Metal Film ResistorE Cap.: Electrolytic Capacitor
VR: Variable ResistorBP E Cap.: Bi-Polar (or Non-Polar)

MF R : Metal Film Resistor Electrolytic Capacitor

CMF R: Coating Metal Film ResistorMM Cap.: Metalized Mylar Capacitor
UNF R: Nonflammable ResistorPP Cap.: Polypropylene Capacitor
FR: Fusible ResistorMPP Cap.: Metalized PP Capacitor

PS Cap : Polystyrol Capacitor Tan. Cap. : Tantal Capacitor

NOTE: When ordering replacement parts please specify the part number as shown in this list including part name, and model number. Complete information will help expedite the order. Use of substitute replacement parts which do not have the same safety characteristics as specified, may create shock, fire or other hazards. For maximum reliability and performance, all parts should be replaced by those having identical specifications.

SERVICE REPLACEMENT PARTS LIST

Symbol Description Part Number

Main P.C.B. Ass'y SU-1133A CRT Socket P.C.B. Ass'y SU-3032A Purity Shield Ass'y 07-220083-03

Page 67

Outside of the P.C.B. Ass'y Symbol Description Picture Tube 19” rN A\Deflection Yoke PC Magnet A AFlyback Transf. aA ASHVR ROS UNF Resistor 2209,25W K C04 C Capacitor 150pF, AC1.5KV X01 Si, Transistor X02 Si. Transistor sc Screw #8-% sc Screw % x % Pix Tube Mtg. (4) WA Pyramidal Lock Washer (4) Nut Retainer, Pix Tube Mtg. (4) Clip — P.C.B. Support Standoff Wire Terminal (Gnd. Strap) Terminal Lug (Gnd.) Groundstrap Assy. Grounding Spring Wire Hook (Gnd. Strap) Purity Shield Holddown Clamp Support Brkt. RH Support Brkt. LH Chassis Base Yoke Wedge (3)

Purity Shield Ass’y. Parts List

Symbol Description Degaussing Coil D911, D912 Rectifier 1 Amp 600V (2) Pin Terminal (2) Pin Terminal Housing Purity Shield (2 pes.) Purity Shield (2 pcs.) C911 Capacitor 100nF 10% 400V R921 Resistor, Wirewound 332, 4W Fire Retardent Term. Strip 4 Lug

CRT Socket P.C.B. Ass’y (SU-3032A) Parts List

Resistors Symbol Description

R3105VvR 200
R3106VvR 200
R3113vR 5K
R3114vR 5K
R3115vR 5K
R3116OMR10KQ2W J
R3117OMR10KQ2W J
R3118OMR10KQ2W J

R3119 Comp. R 3.3KQ%W K R3120 Comp. R 3.3KQ%W K C3121 Comp. R 3.3KQ%W K

Capacitors Symbol Description

C3107ECap.10uF 250V A
C3108CCap.1000pF DC1400V P

Coils Symbol Description L3101 Peaking Coil Part Number 17-7198-03 A29779-D = 21-141-01 A75034-B = 29-32-01 A29951-B A46600-A. QRF258K-221 QCZ0101-005 2SD870 2SC1106A 31-610818-06 31-601418-12 33-255-01 33-494-01 33-629-02 33-670-010R-02 34-228-03 34-33-04 34-574-02 35-212-03 35-3053-02 35-2348-01 35-3890-01 35-3890-02 38-449-02 39-1233-01

Part Number 21-1007-30 28-22-27 34-708-01 34-709-01 35-3847-01 35-3847-02 48-171544-62 42-113301-03 34-492-09

Part Number QVZ3234-022 QVZ3234-022 QVZ3234-053 QVZ3234-053 QVZ3234-053 QRGO029J-103 QRG029J-103 QRG029J-103 QRZ0039-332 QRZ0039-332 QRZ0039-332

Part Number QEWS53EA-106 QCZ9001-102M

Part Number QQL043K-101

Page 68

Semiconductors Symbol 3101 X3102 X3103

Miscellaneous Symbol aA Description Si. Transistor Si. Transistor Si. Transistor

Description ACRT Socket

Main PCB Ass'y (SU-1133A) Parts List

Resistors Symbol R1406 R1408 R1410 R1414 R1415 R1421 R1422 AFR1401 4R1503 R1504 R1509 R1512 R1514 R1515 R1522 R1523 R1528 R1534 VR1501 ASR1703 AXR1704 AR1901 R1902 R1903 R1904 R1905 4Q1908 AR1909 R1910 AXFR1901

Capacitors Symbol C1301 C1402 1407 C1411 C1412 C1508 AC1512 AC1513 AC1514 C1515 C1520 C1523 1524 AC1531 AXC1532 C1904 C1905 Description Vv R Vv CMF OM OM OM Vv AF ACMF Vv OM OM OM CMF CMF

A\CMF A’Posistor UNF CMF om om A\CMF v ACMF AF DUDVDVVVD DVVVUVDVVVVVVVVVVVIVD 2002 2002, 6.8Q1W J 3.3K Q1W J 2.7KQIW J 12KQ2W J 10K2 6822W K 11,.8KQ YW +1% 5Ka 10K 22W J 8.2K22W J 820022W J 8.201W J 4.7021W J 68 22W J 39021W J

39D2W +1% 7.68KQ AW +1%

2Q7W K 4.703W J 10KQ2W J 18KQ1W J 47 QW +1% 2KQ 2.74K QYW +1% 2202%W K

Description BPE Tan. E E E PP AXpP App APP PP BPE E M ANPP APP ( E Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. 3.3uF 50V A 2.2uF 16V K 4.7UF 6.3V A 100uF 160V A 3.3uF 160V A 5600uF 50V J 2000pF DC1500V J 2000pF DC1500V J 2000pF DC1500V J 0.53uF DC1200V J 3.3uF 50V A 1uF 160V A 0.1uF 200V K 2000pF DC1500V J 1500pF DC1500V J

10uF 250V A Part Number 28C1514VC. 2SC1514VC 28C1514VC

Part Number A76068

Part Number QVZ3230-002 QVZ3230-002 QRX019J-6R8 QRG019J-332 QRGC19J-272 QRG026J-123Z QVZ3230-014 QRH024K-680M QRV142F-1182 QVZ3230-053 QRGO26J-103Z QRG026J-822Z QRG026J-821Z QRX019J-8R2 QRX019J-4R7 QRG026J-680Z QRG019J-391 ERZ-C05Z2K471 ERZ-COS5DK271 QRV122F-3902 QRV142F-7681 A75414 QRFO76K-2RO QRX039J-4R7 QRG026J-103Z QRGO019J-183 QRV122F-470Z QVP5A0B-023E QRV142F-2741 QRH124K-221M

Part Number QEN61HA-335Z QEES51CK-225B QEWS1JA-475, QEWS52CA-107 QEWS52CA-335 QFP31HJ-562 QFZ0082-202 QFZ0082-202 QFZ0082-202

  • QFZ0067-534 QEN61HA-335Z QEW62CA-105Z QFM720K-104M QFZ0082-202 QFZ0082-152 QEY0034-001 QEW52EA-106
Page 69

Coils Symbol L1502 L1503 11504

Transformers Symbol T1501 71503

Semiconductors Symbol 101501

X1101 X1102 X1103 X1104 X1105 X1106 X1301 X1302 X1303 X1304 X1305 X1401 X1402 X1501 X1901 X1902

D1101 D1102 D1103 D1301 D1401 D1402

D1503 D1504 D1505 D1506 D1507 01508 AbD1701 A\D1901 A\D1902 A\D1903 A\D1904 A\D1905

Miscellaneous Symbol ANF1901 AF1902

Description Part Number

Linarity Coil A39835 Width Coil C30380-A Heater Choke C30445-A

Hor. Drive Transf. A46022-BM Side Pin Transf. 39050-A

Ic HA11244

Si. Transistor 2SC1685(R) Si. Transistor 2SA673(C) Si. Transistor 2SC1685(R) Si, Transistor 2SA673(C) Si. Transistor 2SC1685(R) Si. Transistor 2SA673(C) Si. Transistor 2SC1685(R) Si. Transistor 2SC1685(R) Si. Transistor 2SA673(C) Si. Transistor 28C1685(R) Si. Transistor 2SC1685(R) Si. Transistor 2S8D478 Si. Transistor 2SD478 Si. Transistor 2SC2610BK Si. Transistor 2SC2688 (K.L.M.) Si. Transistor 2SC1890A (E.F.) Si. Diode ‘WO6A Si. Diode ‘WO6A Si. Diode ‘WO6A Si. Diode 1$Z473H Si. Diode 1$2473H Zener Diode RD10F(C) Si. Diode HF-1 Si. Diode VOSE Zener Diode RD11E(B) Si. Diode ‘WO6A, Si. Diode 18881 Si. Diode 18Z473H AXZener Diode RD20EV2 ASi. Diode 181887A ASI. Diode 181887A ASi. Diode 181887A ASi. Diode 181887A AsZener Diode RD6.8EV3

AsFuse 1.25A QMF53U1-1R25S ANUL Fuse 3A QMF66U1-3R0S

Page 70

if

\co1 POWER REGULATOR mney TR3BS SU-i103A | j mens MAIN PCB ASSY | — —

: See

tea ive ame <8 hy

i

X303 BEAM LIMITE? 2SA673 ny 1 304 BLANKING

  • | 28casac

x304

of

L mi %301,X302,X308,x306 SYNC AMP) Sa |28casac or asci6ss 2103 end XI0$ VIDEO AMR. #°C454C a, 25C\885 | xi02.X104 ond x106 VIDEO AMP 25A673C

+ i oes i ep Geer] x50 shies SU-3016A SRT SOCKET pca assy |

A x30) HORI xOl Wout x70) Manav eaorec or 28ci507 KE, 2scas7iv 250898 or

  • 250434 or 28c26i! or BEz6I0RK 250869 eI B28 cote ACIZOV 6OHL/SOn2 10%

G07-FBO

00-4147-03 Schematic Notes Unless otherwise specified Resistance: (Q.) (K-*KQ, M-~MQ), 1/4 (W) carbon resistor Capacitance: 1 or higher—> (pF), less than 1-> (yF) working voltage» 50 (V) ceramic capacitor Inductance: (v H) Electrolytic Cap: Capacitance Value ( F)/working voltage (V), NP — non-polar (or bipolar) electrolytic cap. Refer to the parts list for additional component information. 2 indicates test point connection hy indicates chassis ground unless otherwise specified Hz indicates cycles per second For safety purposes (and continuing reliability) a replace all components marked with safety symbol with identical type.

NOTE: FR — fusible resistor ———

Parts identification on circuit boards: e.g. SU1126A (R107 = R1107) SU3030A (R113 = R3113)

Page 71

REPLACEMENT PARTS LIST - ELECTROHOME 13” MONITOR

Components identified by the A symbol in the PARTS LIST and on ihe Schematic have special characteristics important to safety. DO NOT degrade the safety of the set through improper servicing.

Abbreviations for Resistors and Capacitors

Resistor Capacitor

CR: Carbon ResistorCc Cap.: Ceramic Capacitor
Comp. R: Composition ResistorM Cap: Mylar Capacitor
OM R: Oxide Metal Film ResistorE Cap.: Electrolytic Capacitor
VR: Variable ResistorBP E Cap.: Bi-Polar (or Non-Polar)

MFR : Metal Film Resistor Electrolytic Capacitor

CMF R: Coating Metal Film ResistorMM Cap.: Metalized Mylar Capacitor
UNF R: Nonflammable ResistorPP Cap.: Polypropylene Capacitor
FR: Fusible ResistorMPP Cap.: Metalized PP Capacitor

7 PS Cap : Polystyrol Capacitor Tan. Cap. : Tantal Capacitor

NOTE: When ordering replacement parts piease specify the part number as shown in this list including part name, and model number. Complete information will help expedite the order. Use of substitute replacement parts which do not have the same safety characteristics as specified, may create shock, fire or other hazards. For maximum reliability and performance, all parts should be replaced by those having identical specifications.
SymbolDescriptionPart Number

Main P.C.B. Ass'y SU-1103A CRT Socket P.C.B. Ass'y SU-3016A

Outside of the P.C.B. Ass’'y

SymbolDescriptionPart Number
voiAsPicture Tube370ESB22(E)
A\DY01A\Deflection Yoke029123-V

PC Magnet A76366-A Wedge 30006 A\Flyback Transf. A19183-A

ARI1AFocus V RA46606-A
AROSUNF Resistor 2202, 25W. KQRF258K-221
Aco4ASC Capacitor 150 pF, AC1.5KVQCZ0101-005
x01Si. Transistor2SD869
1co1IC RegulatorSTR383
Lo1Degausing Coil21-1007-31

Degausing Coil Pin Terminal (2) 34-708-01 Degausing Coil Pin Terminal Housing 34-709-01 Groundstrap Ass'y. 34-697-04 Groundstrap Wire Terminal 34-228-03 Groundstrap Spring (2) 35-3560-01

BRSupport Bracket RH35-3919-01
BRSupport Bracket LH35-3919-02
scSCREW 10-% Pix Tube Mtg. (4)31-631018-08
WAPyramidal Lockwasher (4)33-255-01

Clip P.C.B. Support (2) 33-629-02 Ground Lug 34-33-04

CHChassis Base38-452-01

8-19

Page 72

Main P.C.B. Ass'y (SU-1103A) Parts List

Resistors Symbol R1406 R1408 R146 R1444 R1415 R1421 P1422 AXFR1401 AXR1503 1504 R1509 R1511 R1514 R1515 R1522 R1523 R1528 R1534 VR1501 4R1703 ASR1704 A\R1901 R1902 R1903 R1904 AXFR1901 Capacitors Symbol 1402 C1411 C1412 i508 C1511 Ac1512 AC1513 Ac1514 C1515 1520 C1524 1904 C1905 A\C1907

Colls Symbol 11501 1502 £1503 1504 11901

Transformers Symbol T1501 T1503 CMF R 6.891W J 3.3KQ 1W J 2.7KQ1W J 12KQ2W J 10KQ 6822 K ASCMF Ro 11.8KQYUW +1% VR 5KQ OM R 10KQ2W J OM R 5.6KQ2W J OM R 68022W J CMF R 8.201WJ CMF R 4.721WJ OM R 56N2WJ OM R 39021WJ ZN R ZN R ASCMF R 39K QW +1% 2SCMF Re 7.68KQ.Y%W +1% APosistor UNF R 207WK CMF R 5.623W J OM R 10K22W J AF R 2202%WK fo} = DDDDD

Description Tan.Cap. 2.2uF 16V K E Cap. 100uF 160V A E Cap. 3.3uF 160V A PP Cap. 5600pF 50V J E Cap. 47uF 160V A AXPP Cap. 2000pF DC1500V J AXPP Cap. 2000pF DC1500V J A\PP Cap. 2500pF DC1500V J PP Cap. 0.53uF DC1200V K BPE Cap. 1uF 50VA M Cap. 0.1uF 200V K E Cap. E Cap. 10uF 250V A AXMM Cap. 0.1uF AC150V Z

Description Peaking Coil Liniarty Coil Width Coil Heater Choke Line Filter

Description Hor. Drive Transt. Side Pin Transf.

8-20 Part Number QVZ3230-022 QVZ3230-G2E QRXO019J-6R3 QRGO19J-332 QRG019J-272 QRG029J-123 QVZ3224-014H QRH024K-680M QRV142F-1182 QVZ3230-053 QRG029J-103 QRG029J-562 QRG029J-681 QRX019J-8R2 QRX019J-4R7 ORG029J-560 ORGO019J-391 ERZ-C05ZK471 ERZ-C05DK271 QRV122F-3902 QRV142F-7681 A75414 QRFO76K-2RO QRX039J-5R6 QRG026J-103Z QRH124K-221M

Part Number QEES51CK-225B QEW52CA-107 QEW52CA-335 QFP31HJ-562 QEW52CA-476S QFZ0082-202 QFZ0082-202 QFZ0082-252 QFZ0067-534 QEN61HA-105Z QFM72DK-682M QEY0034-001 QEWS2EA-106 QFZ9008-104

Part Number A75360-6 A39934 C30380-A C30333-A A39475-J

Part Number A46022-BM C39050-A,

Page 73

Semiconductors Symbol 1C1501

1101 x1102 x1103 x1104 x1105 X1106 1301 X1302 X1303 x1304 X1305 x1401 x1402 x1801 x1701 01101 01102 01103 01301 1401 D1402 01503 01504 01505 01506 01507 1508 Ax01701 A\D1901 401902 4401903 A\D1904

Miscellaneous Symbol AXF1901 AF 1902 Description Lc.

Si, Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Diode Si. Diode Si. Si. Si. Diode Zener Diode Si. Diode Si. Diode Zener Diode Si. Diode Si. Diode Si. Diode AdZener Diode ASi. Diode ASi. Asi. Asi.

Description A\Fuse 1A AXUL Fuse 3A

8-21 Part Number HA11244

2SC1685(R) 2SA673(C) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SC1685(R) 28D478 280478 2SC2610BK 2SC1685(P-S) WO6A WO6A WO6A 182473H 182473H RD10F(C) HF-1 VosE RD11E(B) WO6A 18S81 182473H RD20EV2 1S1887A 181887A 1S1887A 1S1887A

Part Number QMF53U1-1ROS QMF66U1-3RO0S

Page 74

CRT Socket P.C.B. Ass’y (SU-3016A) Parts List

Resistors Symbol R3105, R3106 R3113 R3114 R3115, R3116 R3117 R3118 R3119 R3120 R3121

Capacitors Symbol 3107 C3108

Coils Symbol 3101

Semiconductors Symbol X3101 X3102 X3103

Miscellaneous Symbol aA Description 2002 2002, 5KQ 5KQ 5KQ IM 10K 22W J IM. 10K Q2W J OM R 10K22W J Comp. R 3.3KQ%WK Comp. R 3.3KQ%WK Comp. R 3.3KQ%WK oo<<<<< pDDDDDD

Description E Cap. 10uF 250V A C Cap. 1000pF DC1400V P

Description Peaking coil

Description Si. Transistor Si. Transistor Si. Transistor

Description AXCRT Socket

8-22 Part Number QVZ3234-022 QVZ3234-022 QVZ3234-053 QVZ3234-053 QVZ3234-053 QRG029J-103 QRGO29J-103 QRG029J-103 QRZ0039-332 QRZ0039-332 QRZ0039-332

Part Number QEWS2EA-106 QCZ9001-102M

Part Number QQL043K-101

Part Number 2802611 2SC2611 28C2611

Part Number A75522

Page 75

IX Schematics and Wiring Diagrams

Page 76

MONITOR

Pred CPU BD, 200 poetics ass CONN 1 20 108

2 pray Tet sa tw | Pe - LT Jpower supply |! _ none = 3082 = 1 pt = sense 7 se! ey yo Vogt we se Ba wOREeron tt ew 08

Vet ewonprt TT a5_Se
1 gl + ouesisJi
Bah eyaeteoeeooedCee owe oe

Vr! was 2p Ta ' Veg ctu a L J

Oe coy 4s

‘ 4 of

ser pod

MOSI- 00335 - AOOS NOTES: teas wat

SHI ES, aus+mom

SEE ‘i

a—7{ sw RETURNa

sensi ate sane et mace Ewer vest sate | 3 Se E Beh, /MiDWAY sw serie | 10601 W BELMONT FRANKLIN PARK,ILL 6013!

L sanctum we

Page 77

DESCRIPTION LIST

DESIGNATION NO. DESCRIPTION DESIGNATION NO. DESCRIPTION

ol st CERuse|Pa

arat Se a

outc2a.1e38rausivaa|aal
068 uf POLY.7AT4Lsoe3!
390 pf CER"10874LS1388)

"I2R-1C 14a T4LS367 8

"48.aB02-1an SATAJeeengoteSRR SR~a
“6"eos:SH SUBe&
Py*hort;tkERqeRss
Rieke onm 1/4W 5% CARBONIe - ice7aisisaa|ileEf
aaxreerauseesmYmo
“3c74ts04|bewe”
R20K ohm 1/4W 5% CARBON"10T4Ls32=k
R22ik"”"1267aLsa2ca—
asioe3741300re::."
reti50presweseeds
Rea00aa"607aLse6fae
ms"«ce,
R35100.aryats74Fi:seedsSi tte
R3633;araugueaore
aaeDnSF7aus74ersuncen ruereelalplaleelel t lelsiae
Rag1KsoosiFBiel19g2 BALuy wiowaY ure co*‘

: i) 555 TIMER

rel-rea FERRITE BEAD

15 18,38,48,68,98, 28 PIN Ic SocxET

vas 0 Pin CONN

PROWECT ENG! J. SZERSZEN [moon SRcER TIME | 2% / MIDWAY MFG.CO. CROSS REFERENCE LIST

oa ASSEMBLY DRAWING SOUND 1/0 A084-91440-033: PART wo 3 | MO51~ 00333 -D006

SOUND 1/0 BOARD 00333-a032

DESCRIPTIONQ'tyDESIGNATION NO.PART NO.
1S0pt_ cer1cze'0333-00800-0010
390°CER.°c30-c370316-00800- 0002
Olu CER4©4-c18,¢20,c2990808-00800- 0800
68,4 POLY.2€27,c280383-00800 -9005
yt CER,26 0 CPI -ce2610508-00800-0800
lout TANT,1creer0383-00800-0011
lon" CER‘C250333- 00800-0008
2ayt CER4ci6-ci90333- 00800-0007
a7pt CER3c2e-c240388-00800-0008
100p! i6v3c2,¢3,ca10333- 00800-0003,
Loon 25v1ct(0383- 00800- 0009,
330mm aw 5%4R36,838,R39,R430062 07483-1KXX
B2onn aw Sm2R53 Roe
Yooenm2R5,R7,AI3,RIS,R21,0062- 1088~ 1xxx

R23,R25,R27,R29,R31, 32, R35

ra9RS, R4, RE, RIZ, RI,(0062 17983~1xxx

20,822,824, 826,820, 30, R33,R34,R37,R82, 44,848, RSI, RZ

sacsts2Ra0,Ra1(0062-21583 - xxx.
tox"‘i, R2, RAS, REO(0062 ~22783-1xxx
am"1Rao0062-25983 -1xxx
toon286,8470062 -27583-1XXx
\Weohm SIP 9-PIN2RMI RM?0508-00804-0200
0-10Konm POT1vei0385 -00804-0003
9148 o100€“401,02,08,06,08-0180300-00801- 0001
558 TIMER2te rsi3y0333-00803-0008,
BIS AUDIO AMP1Ya(0333- 00803-0036
4119 RAM 2KKef* 10H0550-00803 -5400
2718 EPROM ABOO-'“18(0333- 00803-0019
crc138(0383 - 00803-0020
5ago2-1H480333- 00803- 0021
+8apos-1t“680333- 00803-0022
2732 EPROM AB08-1\"980333 - 00803-0023,
oOAB0s-11rr0385 - 00803-0024
.ABOSA~11“1280333 - 00803-0025
**aB06-11880333- 00803-0026
“8agor=t1880333 - 00803-0027
sopple1a)0333. 00803- 0028
4558 oF AMP150333- 00803-0029
e502 cruH“ae0383-coB03- 0030
7474'Ie0383 00803-0033
rais7120(0333-00803- 0031
74367:exon0333 -00803-0082
74Ls00x9A,30,2F€0300- 00803-0027
74Ls0220300-00803 002
72150429300-00803- 0029
74182020300-00803 0052
74L832\(0300-00803 - 9031
74us42\0333-00803-0034
74U8743* 130, 56,98‘9300-00803- 0032
raises1©(0300-00803- 0054
rausii21a0383-00803 -0007
raise3IC 108,148, 190300- 00803--0033
racsi7e1“70300-00803- 0087
7aLsi966* 2AsAic-ac'0333- 00803-0003
74L8245iWa0333-00803- 0035,
7a1s2033* 6C,70,6F(0300-00803- 0c45,
7418367240268, 124-148,0300-00808-0039,

130-18

74aus3743“ 8c,7¢,8¢0333- 00803-0008
8910 SOUND GEN2* OF, 10F0066- 953ax- xxSx
HEAT SINK, AUDIO AMP'Hsician0068-o71xx- Axcx
24 PIN Ic SOCKET10ICS 18,38, 48,68,98,0808-00804-0500

108, 128,158,158,12H

40 PIN 1c SOCKET3105 9F 108, 12F0508 -0080¢- 1800
EPROM LABEL 4800-1:most - 00383-4024
Ago}-1\MoS! - 00383- A025
&802-1'MoS! 00333 -A028,
ssag03-1'Mos! - 00333 - A027
6gpos-t1Mos! - 00333-A028
8805-1'wos! - 00333-4029
.AB05A-1\Mosi- 00333 -A030,
"apoHiMos!~ 00333-4031
*ag07\Mos!
apis!4MosI- 00383-4033
FERRITE BEAD4Fei-rB40316 - 00804- 0002
50 PIN CONN2J4u50300-0080¢~ 1104

MOUNTING WAROWARE

‘AUDIO AMP MTG, SRW.2nica0017 -00101- 0781

5-404 PHL RND

MTG. HARDWARE-HEAT SINK wasiciaH

SCRW.4-40X5 PHL PAN2=0017-00101 0731
WSH.6 140-,312-032 FLD~0017 -00104-0o8e
NUT 4-40 HEX.2:0017 -00103 -0002
PC.SCRW.6-32X6 PHL PAN4Pew! Poms0017 00101-0339
SWITCH aPos. o1F2swi, swe0300- 00804-0700

080-9140 -D333,

Page 78

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 79

DESIGNATION LIST

onto | PER Ebreraact es DESIGNATION NO. DESCRIPTION DESIGNATION NO. DESCRIPTION DESIGNATION NO. DESCRIPTION

e1ou yt ceneta08eonraceee
3ovat cee.aratseeAtretsser
oscounwotWeetenreser
3‘ooo’oepausesonrecsees
ceOra ces,vratso0BaTetsoe
eaOu ft cer3sratsiesa
aFstenet
bespoo aecore‘74084s2su-t
piledbso28TaLsiesBoeset
¢ te-cataoe3teteresHereusoo
© u2casseuetarasHeRises
aa68745163,ouT4LSITS
cz3S ef OER,7BT4LSI3B,100T4LS S67
orno nt ELECT. evaieeem3atsaer
ceSot Eek3rateswifetsoe
cri-erashat cee-a3:mise

ze reteoe

wsow wan seFsratsoorieairs
a3re aw SeBeraLs30800

na To em wraw oe

oateieisreiersso
nsaro cm yaw 9%terateseenany
aTnek vem omoora tsia3teete
aeoe ew omBeeee
vee 8Lorausist
nere ae oe20retsitevosekgina
rnik vaw 5930751800neracsisa
Riz1k ew 5%=TSLS10vee74L8 196
as1K Maw 5%LiTaLsoereTALS 95
aetaecuaw aeooratsoo7Tatsins
aisSon vaw oaBsreusoe8Hesse
aeSan betea reerearite sz0o
feskew 3%20zitswertwera 2 wir
a47K OW 5%falarea
8Bt nw oeworeuse
#20Sak aw 5%gemacatrecourcru asr oraast w.-02se-2
aoiiee oe130ore

He Oe van se

aLok aw 33oser sopm wate
nesBeen raw 9%3bSer soon wae
aeGoce au 3weerecsis7
aisMeo Va okerratelya owi- JW (C6 nove) £ERO On AEEISTORE
R27470 chm ew 5%ama si63remit -PewnsMETAL STANDING seaceR
ees180 ohm 1/8 5%aracsiesPenne pewnePeMTG. SoRW
nesoom aw amsTesiReMT. Sch
nistao mn vaw 3aerTateos
a3woeraw oe"rise
naesaelaw 8¢Tecsser
8sonvw oh-rats3e7
Bee-n30zex aw omerratsoes
fteam aw sxtrratges

is ratgise fica - ens 620mm 8 pin 405 si iM 89

owateoHTaso

oH atses fan ratsee

orauss0iaSHrises
oeinssoiaonetbee
%cr74.800

[pic “a Sansa eco on BURGER ae Gaby ' MIDWAY MFG.CO. 9-4 ma

Saar ‘ASS'Y DRAWING CPU/DATA Aose-sieai-e933 MO51-00333- E008 ke SO FIN CONN. — 50 PIN CONN

POLApiZiNG TABS.

Wy_seesee=

oe cn

“8 i ‘

E,aae aA OR"
iaBe
d:.

An os et ow Hwy wow

  • ar rn eee’ nemeenar a E | a

~y a.

: 4112]

C1982 saLLY mioway MFG. co ALU RIGHTS RESERVED

5 4 BRe nN©9820

soso. 914s so e339 us Par’ PENoing

NOTE:

INSERT Sut INTO FBI. ww2 WTO F682, JW3 INTO FOS. CROSS REFERENCE LIST

DESCRIPTIONQ'tyDESIGNATION NO.PART_NO.
33 ef CERflces19300-00800- 1400
00 pt1C100300-00800-0500
220 pt1eu19550-00800-2000
390 pf2cee. 280316 00800-0002
470 of4cis-czt19580-00800-0200
1000 otHcs0300-00800-0600
0.01 at CER,2c3,c9.ce7(0808-00800- 0800
Ou pt CER4“61,6,8,cPi-cPas,808-00800- 0900
6.8 at1(0333-00800-0001
22 ati(0333-00800- 0008
f0o'a! ELECT 16V2(0333-00800-0003
22 orm Wvaw 5%'0062 -08883-14xx.
82 ohm’ AW 5%'ase(0082-10483 -1xxx.
180 ohm ew 5%3R28, 29,30(0062-12703 -ixxx
470 ohm 4 5%32 4,5,25,26,27,0062 -15683-1xKx
rkaw 5%6Ri9,iisi2,18, 22,28.(0062 -17983-1xxx
Lek aw 5%3Ris,t79(0082-18783- 14x
22k aw Se©Rad Rae(0062-198 83-1Kxx
33K V/A 5%3215,16,20.(0062-20385-1xxx
47K aw 5%68 7,9440,21,31,32G062-21183-bexr
toxew 5%,‘1,2,8,8.0062- 22785-18xx
30K aw Se'R33)0062 -24983-1xxx
ark aw se'BS062-2582 -1aKK
tkSIP 9 PIN'ew0508 - 00804-0200
84 CHM B FIN 4 POS SIP3pz Hae0333- 00804-0004
DIODE INsi4s'a19100-00801 - 0001
xsTR 2u339143wes(0300-00802 -o00
74Ls00°0 74,30, 30,60,18F,8H,6),74,14J.0300-00808-0027
74s 021an(9300-00803-0028
7408'8(0333 -00803-0012
e1s08r#.6,26,80, 70,6F,6H, 126.(9300-00803-0029,
74usio340, 7F,15K.'0300-00803-0051
rats 20'(0300-00803-0052
raiseri(9300-00803-0053,
Tats 301(0333-00803-0011
748 32'(9300-00803-0031
r4Us 7639300-00803-0032
768 86®(9300-00803-0054
74892(0850-00803-3300
7ausie10333- 00803-0007
74 usies1(9333-00803-0009,
765 138°29300-00803-0033
741515350333-00803-0008
rausis7410,1F, 2,6.(9300-00803-0050
rates'3(0883 - 00803-0010
rausi6s628,38,58,68,36,4F,(9533 -00903-0001
rausire220,8.9300-00803-0047
rai782eat.(9333-00803-0002
ratsi751ou19300-00803- 0035
74Usi986HOLL aU 19,146 50333-00803-0003,
ras 2632ar, i3H(0500-00803-0045
7418 3678{BF.IOF,I1F 104,111,128, 104,110.9300-00803-0039
Taus 3743110,120,180,'9338-00803-0008
2016 RAM 2Kx6'1c 1409508-00803-5400
2ii4-2 STAT RAM31680-1610010550 -00803-0300
251-1 eP— RAM333-15(0333 -00803-0008
2732 EPROM ABC8-'7K0383-00803-0013
B09.ok09333- 00803-0016
aBi0-1H10K9333-00803-0015
agitHl* eK0333-00803-g016
:agie-11* 3K2333-00803 -0017
ieABI1+ 15K0333-00803 -0018
2406 16 SocKeT‘165 7H, 9K, 10K, 12K.48K, 15K"508 00804-0500
EPROM LABEL BOS +'Mos! -00333-A018
EPROM LABEL A809 |1Mosi- 00533-A019
EPROM LABEL 45 10:11MOsI-00355-8020
EPROM LABEL 8811-1HMosi- 00333 -A021
EPROM LABEL 48:12 -11Mos!-00453-a0z2
FROM LABEL AB 13 ~11Mosi- 00333 -AG23,
FERRITE BEA03Fea-res986 0084-0002
weTA 2 we'eran0333-00804 ~0001
SkT50 PIN MALE2ane.0300 -00808-1108
SOPIN CABLE ASSY VPC 82(0333-00804- 0002
ZERO OHM RESISTORS.3x gwi- ows (SEE NOTED
(CPU? Assy CATA EAST m10256-2.crue?nae NR2EX- CANE
METAL SIAND-OFF CAND SPACER¢eewni-40986. 00701 -ooxF
PC MOUNTING SCREWS‘POMS'60!7 00101-0339

ceuroara ce 2000-91441- E935

Page 80

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 81

DESIGNATION LIST

ESIGNATIONDESCRIPTIONoesionation_pescmiPTioN
ena470 wtv2.usLm 305
‘tatotne2-206 SOLID WIRE
Laasoeine4-WASHER, 4,|20-.250-018
augweermaeFtFUSE, 1/44, 810-€10

© Mioway FG, co. 1980 “TO.

ba ‘A082-90427-A000

dil

ALL RIGHTS RESERVED

MEDIUM POWE R SUPPLY 70VA DESCRIPTION

art ope 0.47 yt RO TANT 35 a7 ts tot 470 ut AX.ELEC. 2200 yt 4700 ut * 28,000 pt # 40,000 pt" asv

0.16 onm 15 5% oe" Sw5%, fo * vawsmcREN 24 E . 25 SW 10% 68 = vews% foo" vaws%cRAN 150 2W 10%, 270" vawsK a7 360° > « law % 62k .

100 onm POT

AISF SOV5A DIODE

IN 4001

MR 750 CROSS REFERENCE LIST

A080- s0421-cooo DESIG. Nos PART NOs

_748-09811-0400.DESCRIPTIONQtyDESI. Nos.PART NOS

106.107. 11 0385-00811-0200

neiiee2u2a0s2atoe.10410945-00808 -0300

cior 0948 -00816-100

clos0945 “00811-0800Lar 3052aus-
ice0948- o8t6 -1000°ii abla
cioe.nis2345-00816-0600semmire BEAD2rei.rez0017- o0008- 0228
ens9348 oo8te- 1300:

FERRITE N70. HORW Fans romne cue 0345-00811-0700

SloeO345-00816-1700«206 S010 wine2FaMHI.FBMH2——_0017-00033-0139

cus 2845-00816 1800

HEAT SINK ASSYwear948-00008-0100

R103 0245-00815- 0100

ioe0945-00815-02004-40 x10 SLT RIND2wear0017 - oo1ot-o727
26©062-08183-1xxxMonta. sto 200-018+owsalS017 - 00104-0071
ios0062 -06589-1XxXsag EX NUT2fsaO01oo!

flea Ooas -o08!- 1000 S010 0008

Rids.125.136Soe -09803-iKxXs
heeSess-ioseries,fusevas ovatearieoneess
Rise0945-0081 -0200/patel
mise9248-00812-0200Fuge clip W/sTOP48017-0087! -0083

Riot S062 “i388 100%

ee9062 ISEB 31Ka 505. KK 196 CONNoa3000- 183@7-0200
R127. 129(0062-17983 -1XxxSiNeise001 387-G600
miscose 1e3B3-ixx(on3000-1s387- 800

ee 0062 -21783-inxx

ze ans 22 IN3vmiswe.aws0151-00087-0000
VR100,101,020845-00814-0000Tye weap 7 578 IN2rws.twa0345-09814-0300
THe wrap to 3/0iN2TwiitweO9a8 00814-0800
o10- o1160945-06808-0200rag, Fuse 1/48 SL0-810ae)mosi-00945- aozo
0105.108.109—op4s-00804-0500«TAG Pw SPLY 101tesMoS!- 00848-a0ze
0106. 1070045-co804-080070 VA PWR SPLY Re'
ear sink ASSa0017-90038-0188
proacr exe J JARONaaseo on BLUEPRINT | Guy / MIDWAY MFG.CO.
en pe‘ASSY DRWNG.MED PS.70VA[PART vo

fe rie (A082 -90421- O00) MOS! ~ 00945 - AO3i Jom 12/2/82 A082 -90427- A000

Page 82

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 83

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 84

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.