CATHODE RAY TOMES

atari touchme manual 1974

Touch Me (handheld, rev. 2) (Atari, 1979) · Manual · 10 pages · 11 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

TABLE OF CONTENTS

Page No. A. Introduction and Warranty tnformation ©... +6++++ 1 B. Access and Basic Construction ...+-. +++ rere ress 1 C. New Machine Set-up and Check-out 6.5.2.5 sees 1 D. The Game Sequence... ee : E. The Antenna and The Anti-static Modification ..... 2 :

F. Top Section Sub-Assemblies: Gervice Procedures... 2.5... 5s eee ere eee e

y - om, ~ © LIST OF ILLUSTRATIONS la a ve j Figure sf oupiest ay Touch-MélFront View

  • om View
  • Button Assémbly
  • Wiring Diagram
  • Computer Schematic j 6. Computer Component Location &

wt

ae YN © ATARI, INC, 1974

Page 3

a

A. INTRODUCTIGN AND WARRANTY INFORMATION

Touch-Me is a coin operated amusement devine which tests the concentration and memory-depth of the player. The electronics of this game are solid state for long life and low maintenance. The mechanical assemblies (push bettons and coin mechanism) have been designed modularly for easy removal and servicing. However, as with ai) devices mechanical or electrical, there may be minor.protiems. /f a printed circuit board computer (PCB) fails within the warranty peried, contact the distributor frem whom the game was originally purchased for repair or replacement instructions. Any PCB repair attempted by anyone other than authorized Atari Service Center personnal will void the PCB warranty. If the PCB fails after the one-year (from date of factory shipment} warranty period has expired, it will be repaired for a nominal parts and labor charge.

B: ACCESS AND BASIC CONSTRUCTIGN

‘The lift up top provides convenient access to all subassemblies and adjustment points. Opening the top aiso exposes all the coin handling equipment—ihe coin acceptor and rejector linkage. the coin counter and the cain box. An interlock switch is mounted to the cash deck and turns off the entire machine when the top is opened. The interlock switch protects the operator from accidental shack, so it must always be kept in perfect working order. Hf you need to test or adjust the machine with the top open, place the interlock switch in the closed or “on” position by pulling out the white actuator shaft. All the major sub-assemblies have been designed modulariy for easy servicing or replacement. The control panel, and the Touch-Me computer can each be removed after the wiring and retease bolts have been removed.

C: NEW MACHINE SET-UP AND CHECK OUT PROCEDURES

Befare turning this machine on, inspect it carefully for any damage which may have occurred during shipping. As each new Touch-Me leaves the factory, every component and sub-assembly is carefully checked for proper operation and adjustment. However, since parts may have been damaged or adjustments changed during shipping, the following check out procedure must be repeated prior to placing the machine on jocation,

1, With the machine unplugged, apen the top and carefully inspect both the exterior and interior of the machine for any obvious shipping damage to the cabinet or internal components and sub-assemblies. If any such damage is discovered, contact the carrier immediately. Then contact the distributor from whom the game was originally purchased for repair or replacement instructions.

  • Inspect the interior of the machine more carefully looking for broken or disconnected wires, sub-assembties pulling loose or not firmly mounted and any foreign objects shorting electrical connections. Make sure that the PCB edge connecters and the fuse are firmly seated. Note: The plug is jocated inside the cabinet for shipping purposes, and should be fed thraugh the $%” hole tocated at the left lower bottom portion of the cabinet.
  • Plug m the machine and if the top is up, defeat the interlock switch by pulling out the white actuator shaft, At this point the button lamps should be randomly flashing in the attract mode and mo sound should be heard. The lamp test switch, located in the upper left hand corner of the computer, may be pressed. This should light all of the lamps except the score,
  • Insert several old and new coins into the coin acceptor. No genuine coin should be rejected. One coin should produce game credit and advance coin counter one digit. Check for proper gare sequence, making sure all aspects of the game (score, wait, your turn, miss 1, miss 2, and game over lamps) are functioning carrectly. If you are not familiar with the game sequence for Touch-Me, read the game sequence analysis. :
Page 4

D: THE GAME SEQUENCE

With the game plugged in and the top down, the control panel lamp display will be in the attract made. The attract mode for Touch-Me js the random flashing of the four button lamps, along with watch & wait, and touch & match. Score will remain at some random number when plugged in or where the last giayer left off. Miss 1, miss 2, and game over will remain constantly tit in the attract mode, Cain insertion resets the score to zero and turns off miss 1, miss 2, and game over lamps. The ‘wait’ famp will then light, and one of the four buttons will flash along with its own selected audio tone. The “wait” jamp will

An electronic fateh circuit has been incorporated in the Touch-Me computer, One function of this circuit is to turn off or prevent game credit if a player tries to obtain free games by inducing a static charge in the machine. The antenna wire is an integral part of this system. When a static discharge occurs, an electric current is induced in the antenna wire. This impuise is transmitted through the antenna wire to the electronic latch circuit which turns off game credit and resets the computer to the attract mode, The antenna wire is a length of white wire approximately 12 inches long. One end of the antenna is connected to pin 18 of the PCB edge connector and the ather end has been intentionally left not connected. The length of the antenna wire has been pre-adjusted by the factory to the overall optimum length, hawever some environments may require more or less critical adjustment, then go off and the “your turn” lamp will light, after which the player will have approximately 10 seconds to push the button which had previously flashed. If the player is successful in matching the computer he will score one point. If the wrong button is pushed miss 7 will light and the computer will repeat the same button over. Each time a proper match has been made the computer will add one button to the sequence, thus making the match more complicated, On the third miss match end game will fight and the buttons will go into the attract mode and the score will remain where the player left off.

E: THE ANTENNA WIRE AND ANTI-STATIC MODIFICATION

Lengthening the antenna wire increases the sensitivity of the circuit; cutting the wire shorter decreases the sensitivity. {f players are obtaining free games by inducing static charges in the machine, lengthen the antenna wire (add a piece of wire) by a few inches so that a lesser charge will turn off game credit. If you have problems with static charges accidental/y turning off game credit during the progress of a legitimate game, try cutting thé antenna shorter in increments of 1-2 inches, Try to cut only the minimum amount off the antenna, otherwise players may be able te obtain free fames. The anti-static modification may be tested during a game by touching the end of the antenna wire with your finger as the body usualty has enough capacitance to actuate the electronic latch, If the game is shut off, the circuit is functioning correctly.

F: TOP SECTION SUB-ASSEMBLIES: SERVICE PROCEDURES

Use the following procedures to replace the general ijlumination lamps, the plexiglass screen and adjust volume,

  • GENERAL ILLUMINATION LAMPS: Twenty-six 6 volt lamps are mounted on a PC board behind the plexiglass screen. To replace burned out lamps, untock and fift top. Remove necessary computer hardware and replace with GE44 or GE47.
  • VOLUME ADJUSTMENT: The valume control is located on the computer board near the edge connector and may be set to your preference. However, remember that after adjustment closing the top wiil decrease the volume somewhat. we ae
Page 5

a Cc ay ae

Figure t. Touch-Me - Front View

ITEM

KNMTMO PART NO. A001111 AG01172 A001113 A001114 000909/7 1-1125CU 75456/72-5508 78457/72-5520 7§312/75-7810 75131/75-015S 001961-01 fe soo

40) STAPLE IN Position:

aa weceen N tT TN

DESCRIPTION

Base Assy

Shelf Assy Panel Assy P.C. Board Hinge Assy Coin Acceptor Assy, 25 Screw, Mach, Hex Hd, #1/4-20 x 1/2 Screw, Mach, Hex Hd, #1/4-20 x 1-1/4 Screw, Wood, Rnd Hd, Phil #8 x 5/8 Lg Washer, Flat, #1/4 Extrusion

Page 6

sia n,n os

ne

Figure 2, Touch-Me — Side View

_ ca a

Page 7

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 8

ITEM OAnRWN PART NO. 007136 001143 60012 60009 60011 60010 ary. RADARS

DETAIL B

DESCRIPTION Panel, Plexigias Cup, Switch, ABS Contact Block, SPST, N.O. Switch, Pushbutton, Rundel #R5 Ring, Anti-rotation Cap, Mushroom, 2-1/2” Diam.

Figure 3. Button Assembly

Page 9

oijewayads Jalndwog “g ainbi4

Page 10

Figure 6. Computer Component Location © 3

J rene ano sooner TK (ee maces) [SS em sor <i) @ aes [R]eaue tame 6/4 AcoISER ns APE ROK, Loner snows,