CATHODE RAY TOMES

Lee Trevinos Fighting Golf

Lee Trevino's Fighting Golf (World?) (SNK, 1988) · Manual · 14 pages · 17 sections · original scan

Page 1

2 SSNIKSPERERER"

INSTRUCTION MANUAL

LEE TRE VINO.’ i

HORIZONTAL MONITOR CONVERSION KIT

Page 2

Il.

Ill.

Iv.

VI.

VII.

VIII.

IX. TABLE OF CONTENTS

Introduction

User FCC Information

Game Package Contents Requirements

A. Monitor Compatibility B. Power Supply

C. PCB Specifications and Layout Installation Procedures

A. Placement of PCB

B. Wire Harness Layout

C. Control Panel Configuration

D. Power-up Checklist

Display Test Mode

A. Self ROM Check

Color Test

Control Test

MODE Check

Control Test

FONT Test

G. Sound Check

Optional Settings “moO w

Control Wiring Diagram

Main Harness Connections Com wmnnmnnmnmaidInurnnvdn nuUuuUH a WND

ll

Page 3

OPERATOR NOTICE

Fighting Golf has 2 completely different styles of game play.

Standard Setting:

Player must depress the "A" button once to complete his swing.

Optional Setting:

Player must depress "A" button three times to complete his swing. (This setting recommended for the more avid golf locations).

Should you choose to set Fighting Golf on the Optional setting, SNK has provided an extra set of decals for the optional version.

To change the game play style to the option of depressing the button 3 times change position #4 on dipswitch #1 to the off position.

We believe with these 2 styles of game play, Fighting Golf will earn well in any location it is placed.

Should you have any questions regarding the styles of game play, please contact SNK Corporation of America (408) 736-8844.

OPTIONAL COCKTAIL TABLE SETTING

Fighting Golf offers a feature for a cocktail table setting. The screen will flip for the 2nd player. The control panels are laid out the same on both sides as in Part C, of Part IV Installtion Procedures, except the 1 § 2 player control wires are seperately run to their respective controls. The upright version utilizes one joystick and 1 & 2 player controls are shorted together.

Page 4

FCC WARNING

This equipment operates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications.

It has been tested and found to comply with the limits for a class "A" computing device pursuant to sub-part J of part 15 of F.C.C. rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment.

Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.

SNK Corporation recommends a grounded 3 wire outlet to be used for supplying power.

NOTICE:

Specifications and modifications may be changed without advance notice or warning.

Page 5

GENERAL INFORMATION

INTRODUCTION

Fighting Golf is a Z80 microprocessor based coin-operated electronic game conversion kit for horizontal monitors that makes extensive use of digital integrated circuitry and television monitor concepts. This manual is designed for the use of technicians who possess a general knowledge of solid-state circuitry and video monitor theory. Any individual NOT knowledgeable in these areas SHOULD NOT attempt to install the electronic portions of this conversion kit into a cabinet.

GAME PACKAGE CONTENTS

  • Main Printed Circuit Board (PCB) Assembly
  • PCB Shield (F.C.C. Compliance)
  • SNK Wire Harness
  • Joystick (8 way) Standard
  • Marquee Control Panel Overlay
  • Side Graphic Decals
  • Monitor Card 0 - Control Buttons
  • Instruction Manual
  • Set of Optional Instruction Stickers RRR ENP ERE HE

'

Inspect the entire contents of yor game package to assure it is complete and in satisfactory condition. If any damages have occured during shipment, please notify your SNK distributor immediately.

WARNING

Do not attempt to troubleshoot or repair the PCB if it is found to be faulty or your warranty may be voided and repair charges will be more costly. Always contact an authorized SNK distributor or the SNK Service Manager to troubleshoot your PCB problems.

Whenever you change parts or insert/disconnect the edge connector, always check to make sure the power is off! After you are sure the power is off, wait approximately 10 seconds before proceeding to remove the edge connector to allow time for the power supply to discharge.

Always use caution to stay clear of the high voltage sections to avoid the possibility of electrical shock.

Page 6

REQUIREMENTS

A. MONITOR:

This game requires a HORIZONTALLY MOUNTED RASTER SCAN type monitor with composite sync. If your monitor is one which requires separate syncs, they may be found at the sync combination chip (IC #3E, 74LS86) on the BOTTOM PCB.

2 5A VERTICAL —>: 11 2 3 {-) HORIZONTAL 1 COMPOSITE HORIZONTAL —>: 1 SYNC:

74LS86 74LS367

B. POWER SUPPLY:

SNK recommends the use of a switching type power supply with minimum current ratings as stated below:

Voltage Amperage

+12 VDC 1A + S VDC 8A

  • 5 VDC 1A Ground
Note: The 5 volt line should be measured with a voltmeter at the PCB connector CN4 or CNS when adjustment of the 5 volt supply is being made.
Page 7

C. PCB SPECIFICATIONS:

Operating requirements

Voltage +5.00 volts to 5.10 volts D.C., -5VDC, +12V0C. Amperage 7.5 amps Power 38.5 watts Temperature 0° to 30°C or 32° to 100°F Humidity 95% relative

TOP PCB LAYOUT

kcal : \ MUSIC CPU

——— Volume 2 its Control

A6001 UPO2-02

seca qnnnnnnnnann fh

c L sals Sluvd ac L

Page 8

INSTALLATION PROCEDURES

PLACEMENT OF PCB:

Before mounting PCB, make certain that the wire harness has sufficient "slack/play" between the joystick and the PCB. Mount all four corners of the PCB to assure stability. Allow room for the PCB shield away from the power supply section. Before mounting, please check the wire harness layout.

WIRE HARNESS LAYOUT:

Mark it, PARTS SIDE in order not to reverse connection which may cause damage to the PCB and/or power supply. Layout your wire harness from one player control panel to the PCB edge connector to assure that it is long enough. Remember that the voltage of an intermediate wire harness decreases by contact resistance, so please CONNECT ALL OF THE WIRES PROVIDED FOR THE SUPPLY VOLTAGES AND GROUNDS in order to assure sufficient voltage and to avoid contact burning on the PCB.

CONTROL PANEL CONFIGURATION:

1 +2 PLAYER. swing wp 4 4 swing club © » © “So + 8-way joystick

POSSIBLE 1 AND 2 PLAYER START CONTROL BUTTON LOCATIONS

Control button A (green) is for swing Control button B (blue) is for club selection

Note: short 1 and 2 player controls together.

POWER UP CHECKLIST:

  • Make sure that the Main Wire Harness is wired properly to the Power supply by measuring it with a volt meter.
  • Allow the Power Supply to discharge the voltage for about 10 seconds before connecting or disconnecting the edge connector.
  • Use crimp lugs on all CONTROLS and JOYSTICKS and only solder other connections.
  • Ground all wires and the control panel.
  • Adjust the Power Supply and the Monitor.
  • Check all Controls and set the Dip Switches.
  • Secure the Main Wire Harness with wire ties.
Page 9

DISPLAY TEST MODE

SELF ROM CHECK

The memories are automatically self checked whenever power is applied. To enter the test mode, hold the test switch on when the power is turned on until PICTURE O is displayed. Press the test switch to continue the display tests or reapply power to start the game. You may also set the test switch on Dip 2, Switch 8 upon power up to enter the test mode.

PICTURE O - MODE CHECK

DIP MODE Set desired mode by setting the DIP SWITCHES on the PCB. (Refer vane Ee to the OPTIONAL SETTINGS). When DEPSHITEH 2. Ant Sees O15 % the switch turns on, the number of YEEs10N 7 Tir OVERSEA that BIT will change from 0 to l. NS oe pat cnt

The actual mode will also be dis- com 1 puay my

4 : played. DIPSWITCH 2

SHOT TIME o------- 12 SECONDS BONUS HOLES -2------ Par O/Birdie itegle 2 _. GAME MODE - PLAY HOLES 7 CONTINUE TEST MODE DEMO SOUND ON (OLES 00 2H : on oN

PICTURE 1 - CROSS HATCH

Adjust the monitor for a SQUARE PATTERN throughout the display and on the edge of the monitor.

Assures that the correct colors are properly wired to the monitor. II RED GREEN BLUE WHITE PICTURE 2 - COLOR TEST

Page 10

PICTURE 3 - CONTROL TEST

As a lever or switch turns on, 0 on the monitor will change to 1. Insert coin and confirm that the COIN changes from a 0 to 1. The service switch can also be checked here.

PICTURE 4 - FONT TEST

Confirm that the Characters are displayed on the monitor. There are eight different colors of characters that will be displayed 0 thru 7 automatically.

PICTURE S - SOUND CHECK

Set up the sound Code (''?') to 40-7F or 80-BF by moving the joystick. The music, and special effects will activate when you press Control Button A. If you want to stop the sound, set the Code to OE and press Control Button A. To continue in test mode, depress start 1 control button. 2 LEVER - COIN

P1 UP 0 p2uUP

P1 DOWN 0 P2 DOWN

PYLEFT 0 P2LEFT

P1 RIGHT 0 P2 RIGHT

P1 PUSH1 0 P2 PUSH

P1PUSH2 0 P2 PUSH2

COIN COIN2 eooooao 0

4 FONT 1

COLOR 0

aes FONT CHARACTER

5 SOUND

SOUND CODE = OE

MUSIC 40-7F EFFECT 80-8F Test 3A

STOP OE START 1 next

Page 11

OPTIONAL SETTINGS

DIP SW NO.1

SPECIFICATION

ENGLISH VERSION JAPANESE

NORMAL PICTURE OFF; DISPLAY INVERSE PICTURE ON

CABINETUPRIGHTOFF
STYLECOCKTAILON

sues OPTIONAL 3 HITS DFE GAME STYLE STANDARD 1 HIT ‘ON

1 COIN 1 PLAY OFF | OFF 2 COIN 1 PLAY ON | OFF COIN 1 ee 3 COIN 1 PLAY OFF] ON 4 COIN 1 PLAY ON | ON

DIP SW NO.2

ITEM SPECIFICATION 1/2] 3 J+] sls] 15 SECONDS OFF SHOT TIME 12 SECONDS ON

BONUS PAR _0/BIRDIE 1/EAGLE 2| ON PAR 1/BIRDIE 2/EAGLE 3]orr

ATTRACTIONWITH SOUNDOFF|OFF
SOUNDW/O ATTRACT SOUNDOFF| ON
MONITORSTOP VIDEO DISPLAYON | ONFOR TEST ONLY
SETTINGENDLESS PLAYON {OFF

2 HOLES/COIN orr OFF

PLAY3_HOLES/COINON |OFF
HOLES4 HOLES/COINOFF/ON

5 HOLES/COIN on [ON GAME play [CONTINUE PLAY OFF NON CONTINUOUS PLAY ON

TEST MODE cd ON

NOTE: Bold face suggests factory recommended settings.
Page 12

js ce ies iz

qs ard core eourren RESKEA La) SEEAREA Lal}

BAB EIU |-XIDEQ_DEO

Ti, YIDEQ GNEE! HHEHRERAAH A HAG rmadile i} tod

4-H EEE aH RTS |_| jt F

rr] Heaciiit Hise aiel

| {I Hy Lt a Pie oft cGopEnEap creme jn oa) PUATER > cael Re © en ea

Page 13

MAIN HARNESS CONNECTIONS

CONNECTOR CR7E - 56DA - 3.96E (HIROSE)

Color Key: Stripe / Background

PIN NAME

WIRE COLORSOLDER SIDEPIN #PARTS SIDEWIRE COLOR
BLACKGroundA[1 |.GroundBlack
BLACKGroundB2GroundBlack
RED+5VDCCc I 3+5VDCRED
RED+5VDCD4+5VDCRED
GREEN-5VDCE5-5VDCGREEN
YELLOW+12VDCF | 6+12VDCYELLOW

H 7

J 1 8Coin Counter 1 (-)BROWN

K 9

WHITESpeaker (-)L | 10Speaker (+)WHITE

M }11

LIGHT GREENVideo GreenN }j 12Video RedPINK
GRAY/WHITE_Video SyncP | 13Video BlueLIGHT BLUE
VIOLETService SwitchR | 14Video GroundBLACK
GRAYtilt/resetSs15test switchORANGE
T | 16Coin Switch 1white/violet
WHITE/BLACKStart Switch 2u | 17Start Switch 1white/black
BROWN/BLACK | 2P Control 1 UPVv | 181P Control 1 UPwhite/brown
RED/BLACK2P Control 2 DOWNW || 191P Control2 DOWN | white/red
ORANGE/BLACK | 2P Control 3 LEFTX || 20 | 1P Control 3 LEFTwhite/orange
YELLOW/BLACK | 2P Control 4 RIGHTY | 211P Control 4 RIGHT | white/yellow
GREEN/BLACK | 2P Control 5 PUSH 1Z | 221P Control 5 PUSH 1 | white/green

BLUE/BLACK | 2P Control6 PUSH 2 | a [| 23. | 1P Control 6 PUSH 2 | white/blue b |] 24 c | 25 + d jj 26

BLACKGrounde || 27GroundBLACK
BLACKGroundf | 28GroundBLACK
Page 14

\ eS CORPORATION = SNK SE America 7 ” 246 Sobrante Way Sunnyvale, CA 94086 TEL: (408) 736-8844 FAX: (408) 736-0446