CATHODE RAY TOMES

Mr Driller 2

Mr. Driller 2 (World, DR22 Ver.A) (Namco, 2000) · Manual · 54 pages · 21 sections · original scan

Page 1

namco

Mr DRILLER2 PCB KIT

OPERATION MANUAL

@ Be sure to read this manual thoroughly before using this unit to ensure safe operations. @ Store this operation manual in a convenient location.

Namco Ltd.

Page 2

INTRODUCTION

Thank you very much for purchasing Mr. DRILLER2 PC BOARD KIT (hereafter called “this product”). This operation manual explains the following: @ Installing and connecting this product to a general-purpose game cabinet (hereafter called “cabinet”) safely, @ Adjusting this product for operation safely, @ Operating this product safely, @ Inspecting, cleaning, troubleshooting this product safely, @ Dismounting, safekeeping, and transporting this product safely, @ Disposing this product safely, @ Making full use of the efficiency of this product to operate it right.

Reference for this product and/or for repair: Contact your distributor to make inquiries about this product and/or about repair.

Page 3

1 . SAFETY PRECAUTIONS ~Be sure to read this part for safe use —

To the owner: @ When the owner of this product entrusts the other person(s) to install this product on the cabinet, to

1-1 connect, to adjust for operation, to operate, to inspect, to clean, to troubleshoot, to disassemble, to keep, to transport and to dispose, direct such a person(s) to read the applicable part of this manual before conducting the task and to observe the instructions. When reselling this product, always attach this operation manual to the PC Board.

Level of Danger In this operation manual, the matters that require attention are classified as follows according to the

level of the danger:

WARNING: Players and/or technicians can be killed or seriously injured if such
danger cannot be avoided.
CAUTION: Players and/or technicians can be slightly injured if such danger cannot be avoided. ‘The matters that require attention not concerning safety but functions shall be indicated with the

mark below. (MNeniae : The notices concerning the functions and protection of the product.

Readers of this operation manual This operation manual is written for staff of a location operating amusement game machines. But the part noted with “To be serviced by a qualified service technician only” on the Table of Contents and on the title of each chapter is written especially for a qualified service technician. Such a task should be conducted only by a qualified service technician who would fit the following

requirements.

A qualified service technician : A person who works for designing, manufacturing, inspecting, and maintenance servicing at an amusement machine (AM) manufacturer, and a person who has technical knowledge of electrical engineering, electronics, and mechanical engineering equivalent to a graduate of a technical high school or more, and conducts maintenance services (repair) of an AM equipment on a daily basis.

Page 4

1-3. Safety Precautions

1-3-1 General Safety Precautions

A WARNING :

@ Do not dismount nor modify this product. Do not conduct any works not described in this operation manual. Otherwise an electrical shock or fire may occur. @ This product is designed for indoor use only. Do not install, connect, or operate this product outdoors. It may cause a fire or electrical shock. @ Be sure to use the replacement parts specified by Namco Ltd. Using substitute parts may cause a fire or electrical shock. Contact your distributor to order parts. The replacement parts are listed under “11. Replacement Parts List” on p.50. @ Do not perform any works with wet hands. Otherwise it may cause an electrical shock. @ Tum OFF the power switch of the cabinet and unplug the power cord from an electrical outlet before conducting any works such as installation and connection , inspection, cleaning, troubleshooting, disassembling. Otherwise an electrical shock may happen.

1-3-2 Safety Precautions When Installing and Connecting A WARNING: @ The power source on the cabinet connected to the JAMMA edge connector should fit the following requirements:

  • Voltage allowable error for +5V should be +5%, Amperage should be 2.5A or more
  • Voltage allowable error for +12V should be 5%, Amperage should be 2A or more If the power source does not conform to this requirement, it may cause a fire.
Page 5

1-3-3 Safety Precautions When Operating Av WARNING : @ Should any off-flavor or noise occur, turn OFF the power switch of the cabinet immediately and stop operation. Then unplug the power cord from an electrical outlet and contact your distributor. If the machine is kept operating without solving the trouble, it may cause an electrical shock or fire. @ Make sure that installing and connecting were conducted in accordance with the instructions and the procedure specified in this operation manual (Ref. “5. INSTALLING AND CONNECTING?” on p.9) before operation. If it is not installed and connected correctly, it may cause a fire, electrical shock or machine trouble.

1-3-4 Safety Precautions When Disposing Lv WARNING : @ Do not throw this product into a fire. A lithium battery used in this product may blow to cause injury. @ When disposing this product, collect, transport, and scrap it in accordance with law and orders. @ If entrusting others to collect, transport, and scrap this product, hire specialists in each of such work.

Page 6

TABLE OF CONTENTS

INTORDUCTION

1. SAFETY PRECAUTIONS - Be sure to read this part for safe use —. 1-1 Level of Danger ... i sacndesvencenseeanensess 1-2 Readers of this operation manual ... 1-3 Safety Precautions 1-3-1 General Safety Precautions 1-3-2 Safety Precautions When Installing and Connecting .........sssssecsssesssesceeeecnreesneecnnrecneessaeeeenee 1-3-3 Safety Precautions When Operating . ww NNN ee

1-3-4 Safety Precautions When Disposing .

INSTALLING AND CONNECTING - To be serviced by a qualified service technician only —......... 9 5-1 Before Installing... eanee sovesseesecssesuesssconesssseneeaneesnees 5-2 Installing the PC Board on the Install B Board of the Cabinet 5-3 Connecting to the Cabinets Corresponding to the JAMMA Standard 5-3-1 Checking the JAMMA Edge Connector .......csecssessesssesseessneesssessasessecssecannesssseesseseaneesssesene 5-3-2 Checking the Extended Edge Connector . 5-3-3 Connecting to the Control Panel 5-3-4 Connecting to the Speaker ..... 5-3-5 Connecting to the connectors . 5-4 Pasting the Stickers

6-1 The Basic Knowledge of the Adjustment ....:.....--::sssceeerresrenees 6-1-1 Adjustment Switches, Knobs . 6-1-2 Selecting the Adjusting Items 6-1-3 Finishing the Test Mode ........ssssssscsssssssesseccessnnsececeeesonnaeeseeesnnneseeceesessnssecsssessnanensesesssens

6-2. Display Test (Check/adjustment of the display) .........--ssssssessesssssesssssnnnnnnnsiersenerreereseesesscesecetee 2A 6-2-1 Common Operation .. asa Gash cese cases ta deeet saat 6-2-2 DIAGONAL (Switching interlace mode/non-interlace ce mode)... 6-2-3 COLOR EDIT, COLOR BAR (Adjustment of the shade and tone balance of the picture signal outputted by the PC board) ... avon nssnttsesdsvasusntoesbryosh asta taecnseoupnsvansacaanenersensee DO

Page 7

6-2-4 CONVERGENCE ee the size, position, aspect ratio, distortion of the picture) ... sessesesesesseseseseseensacseacaneanacsonesueneseneaneneeee eee svcsassnsvenecrererentdidiasidhstectenesn SO.

6-4 SOUND TEST (Testisetting of of the 3 sound) 6-5 GAME OPTIONS (Setting of the game options) 6-6 COIN OPTIONS (Setting of play fees) seseseeee 6-7 A.D.S. (Checking the data on playing results in the ne past) 6-8 DATA CLEAR (Clearing various data, initializing to default settings) .

7-1 Persons Not Recommended to Play . 7-2 Restrictions When Operated... 7-3 How to Play ...cessessseceseeseeees

  • INSPECTION & CLEANING, TROUBLESHOOTING
  • To be serviced by a qualified service technician Only — ......csssessesssessseessseesseessneessessseesenessneessnente 8-1 Inspection & Cleaming ....ssssessssssssssecseecsieerseeneersnecsanecsnecsuessueessuesssarcsneesavssssessneccanseseneessneessecennnees 8-2 Troubleshooting ........sssscsssssssesessessseecsseesssessnessecnneessnecsaeesnecesaneessueessuuessaessssessasessecsansessnsennasessnecsneets & EE
  • Disassembling, Safekeeping, Transportation sass AT 9-1 Disassembling —To be serviced by a qualified service technician only 9-2 Safekeeping ...... 9-3 Transportation .....
Page 8

2. SPECIFICATIONS

Item Description

Corresponding Standard JAMMA standard *1

Dimension 268mm x 230mm-x 30mm

Weight 580g

Input power source [Connected to JAMMA standard terminal ] +5V +5% (2.5A or more) and +12V +5% (2.0A or more)

Restriction Indoor use only Temperature : 0°C - 50°C, Humidity : 10% - 85% (no condensation)

Cabinets applicable to connect Cabinets corresponding to JAMMA standard

Direction of the monitor and the monitor signal Direction of the monitor : Sideways Type of scanning retrace line : Switchable to non-interlace / interlace Horizontal synchronizing frequency : 15.75kHz Vertical synchronizing frequency : 60.0Hz

Control panel 4-direction joystick 1x2 Button switch 1x2 Start switch 1x2

How to install it on cabinets Fix to the wooden install board of the cabinet

*1 JAMMA standard (JAMMA STANDARD; abbreviated as JS) Standards on the edge connectors for video game machine PC boards provided by Japan Amusement Machine Manufacturers Association (JAMMA) in 1986

Page 9
  • CHECK OF PACKAGE

This product consists of the following items when out of the factory.

(A ehgssd @ Be sure to check that all the items are included.

@ [If there is something missing, contact your distributor. @ Save the packing materials in case of storage and transportation of this product.

PF

List of items in the package

Item

Mr. DRILLER2 PC Board

Operation Manual This operation manual Title Sheet The logotype of Mr. DRILLER2 is printed. A Sticker * List of basic techniques, rectangular sheet. B Sticker * Control instructions, rectangular sheet.

  • The release type of adhesive is used on the adhesive side of the A sticker, B sticker and Button Seal.

Refer to the chapter “11. REPLACEMENT PARTS LIST” on p.50 for the service parts.

Page 10
  • COMPONENTS

/ mounted side Option switch

Soldered side A

Terminal for the JAMMA Terminal for the extended edge connector stereo sound connector

PC Board

Page 11
  • INSTALLING AND CONNECTING

~ To be serviced by a qualified service technician only —

A WARNING :

@ Always turn off the power switch of the cabinet and unplug the power cord from an electrical outlet before conducting any work. Otherwise an electrical shock may occur. @ This product is designed for indoor use only. Do not install and connect this product outdoors. It may cause a fire or electrical shock.

CaNeyFSJ @ A service technician should not be charged electricity when installing and connecting the product. Static electricity may cause this product breakdown or damage. @ Do not attempt to perform conductivity test using a multi-meter. Even an internal voltage of a multi-meter may damage the IC of the PC board.

Cabinet

Page 12

5-1 Before Installing

You prepare the necessary items to install this product as follows.

(+) Countersunk head.tapping screw (4 pieces) Diameter: one size smaller than the diameter of installation hole on the side of lesslocks which fix lesslocks on the install board. Long enough to fix the lesslocks on the install board but not too long to stick through the install board Length: Operation manual attached to your cabinet Check the handling of your cabinet.

Fix the lesslocks on the install board of your cabinet. You may use the furnished ones with your cabinet. Chapter 5-2 (page 11)

Lesslock (4 pieces) Those which have holes to be installed on the install board and holes to install the PC board

Pan head machine screw (4 pieces) Diameter: appropriate size for the PC board installation hole (or internal thread) of the lesslock. Not too long to stick through the lesslock when the PC board is fixed, or not too short to fix it on the lesslock. You can adjust the length by using the spacer mentioned below in cases the screws are too long. Length:

Spacer (4 pieces) Minor diameter: appropriate size for the screws mentioned above. appropriate size to adjust the length of the screws above. Length:

Solder or caulking, or crimp-style terminal

Insulating heat contraction tube and a drier for heat contraction tube

Insulating tape the PC board. You may use the furnished ones with your cabinet.

Fix the PC board into the lesslocks. You may use the furnished ones with your cabinet,

Adjust the length of the pan head machin screws when installing the PC board on the lesslocks. Not necessary unless the pan head machine screws are too long.

cabinet.

Connect wires to micro switches. Please read the referential chapters to check if they are necessary or not.

Please read the referential chapters to check whether they are necessary or not.

Insulate the edge of unnecessary wires and connectors. Not necessary when connecting to the cabinet corresponding to JAMMA standard with 2 speakers(stereo specification).

~10- Keep space between the install board and

You may use the furnished ones with your

Insulate the connection parts of the wires. e

Chapter 5-3-1 (page 13), Chapter 5-3-3 (page 15), Chapter 5-3-4 (page 16)

Chapter 5-3-1 (page 13), Chapter 5-3-3

Page 13

5-2 Installing the PC Board on the Install Board of the Cabinet

First install the PC board on the install board according to the following procedure. Turn OFF the power switch of the cabinet and unplug the power cord from an electrical outlet.

Read the part on “Installation of the PC board” of the operation manual of your cabinet, and open the door of the PC board storage and take out the PC board install board.

Install board

In cases other PC boards are connected, remove them in accordance with the procedure described in the operation manual of your cabinet.

-il-

Page 14

EA Install the PC board at the center of the install board with the countersunk head tapping screws, lesslocks, spacers (unnecessary if the pan head machine screws are not too long) and pan head machine screws, through the four install holes on the PC board.

(Qesis3) @ Do not use a metal install plate but a wooden board for installation of the PC board. Otherwise it may be short-circuited and damaged. @ Be sure to use pan head machine screws to install the PC board on lesslocks. Using countersunk head screws when spacers are not needed may break the install holes on the PC board.

@ Clean the cabinet with cleaners if it is dirty with dust.

-~12-

Page 15

5-3 Connecting to the Cabinets Corresponding to the JAMMA Standard

5-3-1 Checking the JAMMA Edge Connector

Use the JAMMA edge connector attached to the cabinet to connect this product to the cabinet corresponding to the JAMMA standard. Check if the terminal numbers of the JAMMA edge connector of the cabinet conform to the table of JAMMA edge connectors below. If not, connect wires to that part by soldering or fixing applicable crimp-style terminals. (aNeuessy @ Apply insulating heat contraction tube on the connecting part to prevent shortcircuit.

@ Nothing should be connected to the blank part of the table below. Otherwise the PC board may break down.

JAMMA Edge Connector (56P 3.96 mm pitch)

Soldered side Terminal side Parts mounted side GND GND.

GND GND

+5V +5V +5V +5V

+12V +12V Mis-insert preventive key Mis-insert preventive key Coin counter 2 Coin counter 1

Speaker (-) Speaker (+) Audio (GND) Audio (+) Video (GREEN) Video (RED) Video (SYNC) Video (BLUE) Service switch Video (GND) Test switch Coin switch 2 Coin switch 1 P2 start switch PI start switch P2 joystick (UP) P| joystick (UP) P2 joystick (DOWN) P1 joystick (DOWN) P2 joystick (LEFT) P1 joystick (LEFT) P2 joystick (RIGHT) PI joystick (RIGHT) P2 button switch 1 P1 button switch 1 slolalololpINix<[M|S/<(CGiHnl|aiwAlulzZlZl(r [Alo ac] a[mojayw|>

Page 16

Check the power source for the cabinet connecting to the JAMMA edge connector and voltage of the power source for the coin counter of the cabinet. mS WARNING : @ The power source on the cabinet connected to the JAMMA edge connector should fit the following requirements:

  • Voltage allowable error for +5V should be +5%, Amperage should be 2.5A or more
  • Voltage allowable error for +12V should be +5%, Amperage should be 2A or more If the power source does not conform to this requirement, it may cause a fire.

(Solis @ Voltage of the power source for the coin counter of the cabinet should be +12V or +5V. If higher voltage is used, PC board may malfunction.

5-3-2 Checking the Extended Strereo Sound Connector To connect this product to the cabinet corresponding to the JAMMA standard, use the extended edge connector attached to this product. Check if the terminal numbers of the extended edge connector conform to the following table.

(Qi @ Nothing should be connected to the blank parts of the table. Otherwise the PC board may break down.

Extended Stereo Sound Connector (EI 4P) Terminal number

Speaker R (+) (orange) Speaker R (-) (yellow)

Page 17

5-3-3 Connecting to the Control Panel

This product has to be connected to the control panel (see below) described in the chapter “2. SPECIFICATIONS” (on p.6) to use. P2 4-direction P1 button switch PI start switch P2 start switch Joystick P] 4-direction aie P2 button switch joystick

Turn the power of the cabinet OFF and unplug the power cord from an electrical outlet.

Remove the control panel in accordance with the instructions on “control panel” described in the operation manual of your cabinet.

If the control panel of your cabinet is different from the above drawing, refer to the operation manual of your cabinet and replace the control panel or add/reduce button switches. If some switches are reduced, be sure to fill up the switch holes with hole caps.

1 Install the control panel on the cabinet.

Page 18

5-3-4 Connecting to the Speaker Connect the product to the speaker(s) of your cabinet in the following procedure so that the cabinet outputs the sound.

First check whether your cabinet has one speaker (monaural) or two speakers (stereo).

@ One speaker (monaural) Turn OFF the power switch of the cabinet and unplug the power cord from an electrical outlet.

Conduct a measure to prevent short-circuit, for instance, wrap the edge of the unused wire (A1, B1) of the extended edge harness with insulating tape. After completing all the following connection, switch to “MONAURAL?” in the test mode (Ref. “6-4 SOUND TEST” p.36).

  • “5-2 Installing the PC Board on the Install Board of the Cabinet (p.11)
  • “5-3-1 Checking the JAMMA Edge Connector (p.13)
  • “5-3-2 Checking the Extended Edge Connector (p.14)
  • “5-3-3 Connecting to the Control Panel (p.15)

+ “5-3-5 Connecting to the Connectors (p.17)

  • This product is set as stereo spec. as the factory-setting. When used as stereo spec. with the cabinet of the monaural spec., only the left speaker outputs the sound.

@ Two speakers Turn OFF the power switch of the cabinet and unplug the power cord from an electrical outlet. Connect the wires of the terminals Al and B1 of the extended edge harness to the right side (R) speaker by soldering or fixing an applicable crimp-style terminal in accordance with the following table.

A\ WARNING : @ Always use the extended edge harness specified by Namco Ltd. Otherwise it may cause a fire or electrical shock. Contact your distributor to order parts. Refer to “11. REPLACEMENT PARTS LIST” on p.50 for details of the replacement parts.

  • Speaker R (+) (orange) 4 Speaker R (-) (yellow)

~16—

Page 19

5-3-5 Connecting to the connectors

Turn OFF the power switch of the cabinet and unplug the power cord from an electrical outlet.

Connect the JAMMA edge connector attached to the cabinet and the extended edge connector in the direction shown below so that the mis-insert preventive key would fit the notch of the connector slot of the PC board.

(Meise @ Do not connect the JAMMA edge connector reverse or shifted slightly. The cabinet and PC board may break down.

[> [-—~__ Mis-insert preventive key

Page 20

Put the PC board installed on the install board into the cabinet.

(ayehgssy @ Be sure to fix the install board to the cabinet. If not, it may break down due to vibration.

@ Be careful that the PC board does not touch any harnesses or cables after being put inside the cabinet. If it is kept operating with touching to any of them, it may break down.

~18-

Page 21

5-4 Pasting the Stickers

Paste the stickers included in the package on the cabinet and install it.

Title sheet

A sticker

B sticker

~19—

Page 22

6. ADJUSTMENT FOR OPERATION

The cabinet needs to be conducted adjustment for operation (setting or altering) in order to operate

Mr. DRILLER game.

The following items can be adjusted.

Item Reference

Check/adjustment of the display 6-2 Display Test (p.24) Testing switches connected to PC board 6-3 Switch Test (p.32) Testing sound output and setting speakers 6-4 Sound Test (p.33) Setting of the game options 6-5 Game Options (p.35) Setting of play fees 6-6 Coin Options (p.37) Actual play data 6-7 A.D.S. (p.39) Clear the data 6-8 Data Clear (p.40)

Use the adjustment switches on the PC board and the switches on the control panel of the cabinet to make adjustment. The basic knowledge of the various adjustment switches and the adjusting procedures necessary for operation shall be explained here.

6-1 The Basic Knowledge of the Adjustment (Selita @ A service technician should not be charged electricity when touching the PC board. ry Static electricity may cause the product breakdown or damage.

Page 23

6-1-1 Adjustment Switches, Knobs The PC board has a switch and a knob for adjustment, the option switch and speaker volume. @® Option switch

  • No.1 shall be used to switch the test mode/game mode. ON: Test mode OFF: Game mode
  • No.2~8 shall be not used

@ These should be OFF when operating the game. @ Speaker volume.(knob) This knob adjusts the volume of the speaker sound of the cabinet.

  • Tum to right : Sound volume increases
  • Tum to left : Sound volume decreases

® Speaker volume (knob)

~21—

Page 24

6-1-2 Selecting the Adjusting Items Display the test menu screen on the test mode to make adjustment. Turn the power switch of the cabinet ON to display the game screen.

Turn No.1 option switch (©) ON.

  • Option switch (©) on the PC board and the slide type test switch on the cabinet can make it enter the test mode only when they are switched from OFF to ON. They cannot make it enter the test mode even when they are already set ON. In this case, you have to turn it OFF and then turn it ON again.

It enters the test mode and the test menu screen appears.

  • You may perform the procedure to return to the test menu from each test under “6-2 Display Test” (p.24) through “6-8 Data Clear” (p.40) to display the test menu.

DISPLAY TEST Display test SOUND TEST Sound test

SWITCH TEST Switch test

JVS CABINET OPTIONS Cannot select GAME OPTIONS Game option COIN OPTIONS Coin option A.D.S. Check play data DATA CLEAR Data clear EXIT & SAVE Finishing the test mode ------ (6-1-3)

TEST SELECT ENTER :P1-UP or P1-DOWN :P1-BUTTON

Page 25

Hit the P14-direction joystick up or down to turn the item to be adjusted in red referring to “6- 2 Display Test” (p.24) through “6-9 Data Clear” (p.40).

P1 4-direction joystick oe 228 e /

The items to be adjusted can be selected through the following list.

Adjustment Item to be selected Reference

Check/adjustment of the displayDISPLAY TESTp.24
Testing switches connected to PC boardSWITCH TESTp.32
Testing sound output and setting speakersSOUND TESTp.33
Setting of the game optionsGAME OPTIONSp.35
Setting of play feesCOIN OPTIONSp.37
Actual play dataA.D.Sp.39
Clear the dataDATA CLEARp.40

Press the P1 button switch 1 to select the test screen. The test screen selected is displayed.

uae,

Make’ adjustment on the test screen selected. The detailed adjustment procedure shall be explained under each chapter from “6-2 Display Test” (p.24) through “6-8 Data Clear” (p.40).

Page 26

6-1-3 Finishing the Test Mode

After making adjustment of each item according to “6-2 Display Test” (p.24) through “6-8 Data Clear” (p.40), display the test menu screen.

Hit the P1 4-direction joystick up or down to turn “EXIT & SAVE” in red.

Press the P1 button switch. The test mode finishes and it returns to the game screen.

P1 button switch

8e 3 Ss

Turn No.1 option switch (©) OFF.

  • Incase that the test switch on the cabinet is used, turn that test switch OFF. PI 4-direction joystick

@ Ifthe test mode is not finished in the above procedure, the adjusted result (setting or altering) may not be effective. Always finish the test mode in the above procedure. (The test mode cannot be finished only turning the test switch OFF without selecting “EXIT & SAVE”.)

6-2 Display Test (Check/adjustment of the display)

The following check and adjustment shall be made.

¢ COLOR EDIT The shade and tone balance of the picture signal outputted by the PC board shall be checked and adjusted.

  • DIAGONAL The interlace mode display shall be checked.

*« COLOR BAR It is used to check/adjust the shade and the tone balance of the picture.

  • CONVERGENCE It is used to check/adjust the size, position, aspect ratio, distortion of the picture.

Before conducting any of the above, conduct the following “common operation”.

Page 27

6-2-1 Common Operation Perform the procedure Mill - El of “6-1-2 Selecting the Asus Items” (p.22-23). Select “DISPLAY TEST” in El.

“Color Edit” screen shall be displayed over the “diagonal” screen as follows.

Color edit screen

: ‘SubContG £88 SubContB : OO Wi V : ‘Al parvious MALUE EDIT. Rex COLOR TEST P1-START

Color edit screen is displayed over the diagonal screen.

  • Pressing the P1 button switch the “color edit” screen displayed/non-displayed.

DIAGONAL,

ENTER COLOR EDIT:P2-BUTTON1How to enter the color edit mode
NEXT COLOR TEST:P1-BUTTON1How to go to the next test pattern
EXIT2P1-STARTHow to retum to the test menu screen

The color edit screen is not displayed

Page 28

BZ Press the P! button switch to go the other adjustment item.

  • Each time you Press the P1 button switch, it shifts from “DIAGONAL” -> “COLOR BAR” -> “CONVERGENCE” -> “DIAGONAL” ....., and its screen is displayed each time.

P1 button switch Pi 1 switch

Ls = Se9 e /

According to the item to be adjusted, perform the procedure described under “6-2-2 DIAGONAL” (p.26) through “6-2-4 CONVERGENCE” (p.30). EZ] Press the P1 start switch to retum to the test menu screen after completing the whole “DISPLAY TEST”. The test menu screen (p.22) is displayed. Perform “6-1-3 Finishing the Test Mode” (p.24) to exit the test mode. Lo}

6-2-2. DIAGONAL (Switching interlace mode/non-interlace mode)

Interlace mode: The mode where precise expression, curves and smooth lines shall be displayed compared to “non-interlace mode”. The vertical resolution is doubled without changing the horizontal/vertical frequency by shifting the display position of the screen to the vertical direction by half of one line once out of twice in display.

  • Namco-made CYBERLEAD cabinet corresponds to the interlace mode setting. Non-interlace mode: The mode to be used when slanted lines are irregular, or the whole screen flickers in “Interlace mode”. This mode keeps the screen pictures uniform every time without shifting the display position of the screen.

Perform the procedures Kil and BJ of “6-2-1 Common Operation” (p.25) to display the “Color edit” screen over the “Diagonal” screen.

  • If “DISPLAY TEST” screen appears already, common operation Ml is not needed.
Page 29

DIAGONAL, > Interlace Interlace mode Contrast Re Bright SubContR : QO SubContG : 2 SubContB :

PREVIOUS VALUE:‘STARTHow to initialize the value
EXIT COLOR EDIT:How to finish the color edit
NEXT COLOR TEST:How to go to the next test pattern

EXIT : P1-START 1) How to return to the test menu screen

CaNeyissy @ If the “DIAGONAL” screen is not displayed, keep pressing the P1 button switch until it is displayed.

  • Each time you press the P1 button switch, it shifts from “DIAGONAL” -> “COLOR BAR” -> “CONVERGENCE?” -> “DIAGONAL!” ....., and its screen is displayed each time. @ [If the “Color Edit” screen is not displayed, press the P2 button switch. The “Color Edit” screen is displayed over the “DIAGONAL” screen.
  • Press the P2 button switch to switch the “Color Edit” screen displayed / nondisplayed.

PI button switch

& we SOS P2 button switch

Make sure that “Interlace” is selected at the right top of the screen.

  • If it is “Non Interlace”, change the setting to “Interlace” by following the steps below. @® Hit the Pl 4-direction joystick to up or down to select “Non Interlace” at the right top of the screen. The arrow on the left of “Non Interlace” shows that it is selected.

® Hit the P1 4-direction joystick to right or left to change the setting from “Non Interlace” to “Interlace”.

Hit the P1 4-direction joystick to right at the same time to check that slanted lines are not irregular in every color, or the whole screen does not flicker.

Page 30
  • Each time you Hit the P2 4-direction joystick to right, the color of the slanted lines pattern changes from white -> blue -> red -> purple -> green -> light blue -> yellow -> black -> white ......in this order.
  • In the Interlace mode, precise picture can be displayed compared to the Non Interlace mode. Due to the nature of the Interlace mode, however, some types of monitor cannot display the right picture, where slanted lines may be irregular or the whole screen may flicker.

When slanted lines are irregular or the whole screen flickers, switch “Interlace” to “Non Interlace” at the top right of the screen following the steps below. @ Hit the Pl 4-direction joystick to up or down to select “Interlace” at the right top of the screen. The arrow on the left of “Interlace” shows that it is selected.

® Hit the P1 4-direction joystick to right or left to change the setting from “Interlace” to “Non Interlace”.

P1 button switch PI start switch se PI 4-direction joystick

Press the P1 start switch to return to the test menu screen after completing the whole “DISPLAY TEST”.

Press the P1 button switch | to display the adjusting screen for the other adjustment in the “DISPLAY TEST”.

Perform “6-1-3 Finishing the Test Mode” (p.24) to exit the test mode.

Page 31

6-2-3 COLOR EDIT, COLOR BAR (Adjustment of the shade and tone balance of the picture signal outputted by the PC board) Perform the procedures El and Bd of “6-2-1 Common Operation” (p.25) to display the “Color Edit” screen over the “Color Bar” screen.

  • If “DISPLAY TEST” screen appears already, common operation Ell is not needed. In the “Color Bar”, the following screen appears.
  • Each color bar of “white” “red” “green” “blue” is displayed with gradual shading. Hit the P2 4-direction joystick to right to change the shade and tone of the color from 32 -> 16 ->8 ->4->2->32......in this order.

P1 4-direction joystick iin TY,

> Contact Whole contrast COLOR BAR tial : whole gmt SubContR : anleestiiee) ) iG: ‘ontrast(green! SubcontB | OO. |Contastblue) Color bar (white)

Color bar (red)

Color bar (green)

Color bar (blue)

PREVIOUS VALUE:AHow to initialize the value
EXIT COLOR EDIT.:How to finish the color edit
NEXT COLOR TEST:How to go to the next test pattern
Exit:How to return to the test menu screen

(Aen @ If the “COLOR BAR” screen is not displayed, keep pressing the P1 button switch to down until it is displayed.

  • Each time you press the P1 button switch, it shifts from “DIAGONAL” -> “COLOR BAR” -> “CONVERGENCE” -> “DIAGONAL” ....., and its screen is displayed each time. @ If the “Color Edit” screen is not displayed, press the P2 button switch. The “Color Edit” screen is displayed over the “COLOR BAR” screen.
  • Press the P2 button switch the “Color Edit” screen displayed / non-displayed.
Page 32

“BA Hit the Pl 4-direction joystick to up or down to select the adjusting item out or Contrast”, “Bright”, “SubCont R”, “SubCont G”, and “SubCont B”. PI button switch P! Start switeh 9 start switch P2 button switch P1 4-direction joystick re Ns S g a /

Hit the P1 4-direction joystick to right or left to change the setting.

  • The details of the adjustment is shown in the table below. The result of the adjustment shall be checked on the color bar on the screen.

Item Description Contrast | Adjusting contrast of the picture | Bright Adjusting shade and tone of the picture SubCont R | Adjusting contrast of red color of the picture signal SubCont G | Adjusting contrast of green color of the picture signal SubCont B | Adjusting contrast of blue color of the picture signal

  • After changing the setting,
  • To initialize the settings, press the P2 start switch. The changed settings are erased.
  • To stop adjusting, press the P2 button switch. The “Color Edit” screen disappears and adjustment is suspended.
  • To re-adjust, press the P2 button switch again. The “Color Edit” screen appears again for re-adjustment.

G1 Press the P1 start switch to return to the test menu screen after completing the whole “DISPLAY TEST”.

Press the P1 button switch to display the adjusting screen for the other adjustment in the “DISPLAY TEST”.

1 Perform “6-1-3 Finishing the Test Mode” (p.24) to exit the test mode,

6-2-4 CONVERGENCE (Checking/adjusting the size, position, aspect ratio, distortion of the picture) Perform the procedures Ml and El of “6-2-1 Common Operation” (p.25) to displayd the “CONVERGENCE?” screen.

  • If“DISPLAY TEST” screen appears already, common operation Mi is not needed.
Page 33

[Hes] @ If the “CONVERGENCE?” screen is not displayed, keep pressing the P1 button switch until it is displayed.

  • Each time you press the P1 button switch, it shifts from “DIAGONAL” -> “COLOR BAR” -> “CONVERGENCE” -> “DIAGONAL.” ..... , and its screen is displayed each time.On the “CONVERGENCE?” screen, the following “cross hatch pattern” is displayed.

CONVERGENCE t

Cross hatch pattern

ENTER COLOR EDIT:P2-BUTTONIHow to enter the color edit
NEXT COLOR TEST:P1-BUTTON1How to go to the next test pattern
EXIT_2PI-START., _| How to return to the test menu screen
Note: The above shows the screen with the color edit non-displayed. It makes no difference if the color edit is displayed.

Hit the P2 4-direction joystick to right at the same time to check the size, position, aspect ratio, and distortion of the cross hatch pattern on each color. PI 4-direction P! button switch P2 4-direction

  • Each time you hit the P2 4- joystick joystick direction joystick to right at

the same time, the color of the [SXS) eo

“cross hatch pattern” changes from.white -> blue -> red -> purple -> green -> light blue - > yellow -> black -> white «+.in this order.

When the size, position, aspect ratio of the pattern is not appropriate or distorted, refer to the operation manual of the cabinet or contact the manufacturer of the cabinet to adjust it on the cabinet.

Press the P1 start switch to return to the test menu screen after completing the whole “DISPLAY TEST”.

Press the P1 button switch to display the adjusting screen for the other adjustment in the “DISPLAY TEST”.

Perform “6-1-3 Finishing the Test Mode” (p.24) to exit the test mode.

Page 34

6-4. SWITCH TEST Use the SWITCH TEST function to test the switches connected to the PC board such as the buttons

on the control panel. Perform the procedure Ell - Ei of “6-1-2 Selecting the Adjusting Items” (p.22-23). 3elect “SWITCH TEST” in El.

The following screen is displayed.

No use No use P2 4-direction joystick P2 start switch

SWITCH TEST P2 button switch 1

00 2P ;4000 P| start switch No use

PI 4-direction joystick

P1 button switch 1 No use SERVICE :OFF TEST SW:0F DPSW 112345078 Service switch of the cabinet No use

Test switch of the cabinet No use

Option switches of the PC board EXT ‘The number of activation the coin counter (initially No use How to return to the test menu screen No use

Notes: * The button switches not specified in the above figure shall not be used. + The current status shall be displayed under “SERVICE”, “TEST SW”, “DIP SW”, “COIN 1”, “COIN 2”. (In case that there is only one coin counter, 0 shall be displayed under “COIN 2”.

Page 35

EZ Operate each joystick and switch on the control panel one by one.

  • The joysticks on the screen moves in accordance with the actual moves of “P1 4-direction joystick” . The button on the screen is highlighted in white when the actual button switch on the control panel is pressed. C ile} s38 @ If the screen does not change in accordance with the operation of the joysticks and the switches on the PC board, the game play cannot be played correctly. Refer to “8-2 TROUBLESHOOTING” (p.45) in that case.

Press the P1 button switch and P2 button switch at the same time to return to the test menu screen.

P1 button switch P2 button switch

Perform “6-1-3 Finishing the Test Mode” (p.27) to exit the test mode.

6-4 SOUND TEST (Test/setting of the sound)

Testing of the sound output of the cabinet and the setting of the speakers monaural/stereo shall be made here. Perform the procedure ll - EJ of “6-1-2 Selecting the Adjusting Items” (p.22-23). Select “SOUND TEST” in Ef. Tdistributor to make inquiries about this product and/or about repair.

SOUND TEST

LEFT OUTPUT RIGHT Status of sound output

SPEAKER OUT: STEREO ‘Current setting; monaural/stereo

TEST SOUND: P1—BUTTON1How to play the sound
SETIMONAURAL]: P2-BUTTON1How to change the setting of monaural/stereo
EXIT:_P1—STARTHow to return to the test menu screen
Page 36

EX Make adjustment according to the description on the table below with the appropriate joystick

and the switch.

Item Test/Adjustment How to operate Stereo sound test Stereo sound output is tested. Press the P1 button switch. The sound is played from the left speaker, right speaker, and finally both speakers as stereophonic. Switch monaural/stereo Monaural sound/stereo sound is| Press the P2 button switch. switched.

(Here © If something wrong is found when checking the adjustment, refer to “8-2 TROUBLESHOOTING?” on p.45.

Press the P1 start switch to return to the test menu screen.

Pl button switch PJ start switch P2 button switch [ts Beg oe,

GA Perform “6-1-3 Finishing the Test Mode” (p.24) to exit the test mode.

~34—

Page 37

6-5 GAME OPTIONS (Setting of the game options)

Game options such as the game difficulties shall be set here. Perform the procedure Ell - EZ of “6-1-2 Selecting the Adjusting Items” (p.22-23). elect “GAME OPTIONS” in El.

The following screen is displayed.

  • | 500m(2500ft) DIFFICULTY LEVEL :MEDIUM
  • | 1000m(SOO0Oft) DIFFICULTY LEVEL :MEDIUM () | 2000m(10000ft) DIFFICULTY LEVEL:MEDIUM (@ | LIVES :3 ©

(®) | EASY DIFFICULTY LEVEL

  • | NORMAL DIFFICULTY LEVEL
  • | HARD DIFFICULTY LEVEL q@ | LIVES @ | MUSIC&VOICE IN ATTRACT

Hit the Pl 4-direction joystick up or down to select an item to change the setting out of (a) - (j) on the above figure. The selected item is highlighted in red. Li oe ee g eo Y,

EJ Hit the Pl 4-direction joystick right or left to change the setting. P1 4-direction joystick

The details of the setting of each item are as follows. (The default setting out of factory is shown by the thick frame here.)

1P PLAY MODE

  • 500m(2500ft) DIFFICULTY LEVEL(Difficulty of the game play in 500m(2500ft)mode) EASY [warp | very Harp
  • 1000m(5000ft) DIFFICULTY LEVEL(Difficulty of the game play in 1000m(5000ft) mode)

EASY HARD VERY HARD

  • 2000m(10000ft) DIFFICULTY LEVEL(Difficulty of the game play in 2000m(10000ft) mode)

EASY MEDIUM HARD. VERY HARD

Page 38
  • LIVES(The number of life in game)

! 2 4 5

(@) 1UP(Extend of life)

2P PLAY MODE

  • EASY DIFFICULTY LEVEL(Difficulty of the game play in easy mode)
MEDIUM|HARD.VERY HARD
  • NORMAL DIFFICULTY LEVEL(Difficulty of the game play in normal mode)
EASYHARDVERY HARD
  • HARD DIFFICULTY LEVEL (Difficulty of the game play in hard mode)
EASYMEDIUMHARDVERY HARD

+The setting in the easy difficulty mode cannot be higher than the settings for normal and hard difficulty modes. ‘The setting in the normal difficulty mode cannot be higher than the settings for hard difficulty

modes.

  • LIVES(The number of life in game)

1 2

ATTRACT MODE () MUSIC&VOICE_IN ATTRACT(Sound played in attract mode)

YES(possible) NO(impossible)

Press the P1 start switch to return to the test menu screen.

Pi start switch (Bo 237

Perform “6-1-3 Finishing the Test Mode” (p.24) to exit the test mode.

Page 39

6-6 COIN OPTIONS (Setting of play fees)

Coin options such as the credit needed to play one game play shall be set here. El Perform the procedure Ell - E¥ of “6-1-2 Selecting the Adjusting Items” (p.22-23). Select “COIN OPTIONS” in Ef.

The following screen is displayed.

COIN OPTIONS <DEFAULTS IN GREEN>

  • | — START COST: 1 COIN TO START
  • CONTINUE COST: 1 COIN TO CONTINUE (©) COIN CHUTE1 MECHANICAL VALUE: 1 COIN COUNT AS 1 COIN qd) COIN CHUTE2 MeCN VALUE: 1 COIN COUNT AS 1 COIN © CREDIT MODE: --- +--+ etter dee can not change COMMON ® COIN COUNTER:

(g)

SELECT :P1-LEFT or P1-RIGHTHow to changethe settin;

eke H i ARPT How to return to the test nena screen

Hit the P1 4-direction joystick up or down to select an item to change the setting out of (a) - (g) on the above figure. The selected item is highlighted in red. (Mesias @ Before changing the settings of (a) - (f), be sure to set OFF (g) “FREE PLAY”. The settings of (a) - (f) cannot be changed if (g) is set ON.

Hit the P1 4-direction joystick right or left to change the setting.

P1 4-direction joystick

ieee,

The details of the setting of each item are as follows. (The default setting out of factory is shown by the thick frame here.)

  • START COST (The number of coin(s) needed to play an initial game play)
123456789 _| COIN(S) TO START
  • CONTINUE COST (the number of coin(s) needed to play a continued play)
123456789 | COIN(S) TO START
Page 40
  • COIN CHUTE | MECHANICAL VALUE (The number of coin(s) to be added when the coin switch | activates once) 1 COIN COUNTAS |_1 2 3 4 5 6 7 8 9 | COIN
  • COIN CHUTE 2 MECHANICAL VALUE (The number of coin(s) to be added when the coin switch 2 activates once) 1 COIN COUNT AS tJ 2 3 4 5 6 7 8 9 | COIN
  • CREDIT MODE (Record of credit) Credit mode is fixed to set “COMMON” only and cannot be changed.
  • COIN COUNTER (Allocation of the coin counter)

1 COUNTER 2 COUNTERS (Two coin switches uses one coin counter in (Each of two coin switches uses own coin common.) counter.)

Notes: © The cabinet corresponding to the JAMMA VIDEO standard (JVS) with one coin counter is fixed to set “1 COUNTER” and cannot be changed to “2 COUNTERS”.

  • When two cabinets corresponding to the JAMMA VIDEO standard (JVS) are linked to set networked play, it is fixed to set “2 COUNTERS” and cannot be changed to “1 COUNTER”.
  • FREE PLAY (Setting of free play) YES (coins needed) | NO (no coins)

Press the P1 start switch to return to the test menu screen.

Pl 4-direction P1 button switch PI start switch aren oie,

Perform “6-1-3 Finishing the Test Mode” (p.24) to exit the test mode.

Page 41

6-7 A.D.S. (Checking the data on playing results in the past)

The data on playing results in the past such as the total playing time can be checked here. Perform the procedure El - Ell of “6-1-2 Selecting the Adjusting Items” (p.22-23). Select “AD.S.” in Bb.

Press the P1 start switch to return to the test menu screen.

P1 4-direction PI start switch joystick es Sse 2 6 S

Perform “6-1-3 Finishing the Test Mode” (p.24) to exit the test mode.

Page 42

6-8 DATA CLEAR (Clearing various data, initializing to default settings)

The data saved even after the power is turned off can be erased or initialized to the default value as factory-setting. This “DATA CLEAR” function is used to erase the data or initialize it. Perform the procedure El - 4 of “6-1-2 Selecting the Adjusting Items” (p.22-23). Select “DATA CLEAR” in El.

The following screen is displayed.

DATA CLEAR

  • | CANCEL Retum fo the test menu screen (b)| A.D.S DATA CLEAR Clear the playing data only
  • | RANKING CLEAR Initialize the ranking data
  • | SET DEFAULTS ALL OPTIONS Set the value of all the options to default
  • | ALL CLEAR Clear all the data recorded

EXECUTE : BUTTON H (EXTOT: START How to return (othe test mena

Hit the P1 4-direction joystick up or down to select an item to erase or initialize the data out of

  • - (e) on the above figure. The selected item is highlighted in red.

@e 222 eo /

What to be executed Item displayed on the screen Pl 4-direction joystick

(1)Erase only the A.D.S. data (Ref. “6-7 A.D.S.” on p.39)A.D.S. CLEAR
(2)Initialize the ranking data, such as high score, toRANKING CLEAR

default value as factory-setting.

(3)Initialize the values of all the options set in the test modeSET DEFAULTS ALL OPTIONS

(Ref. “6-2 DISPLAY TEST” on p.24 through “6-7 A.D.S.” on p.39) to default values as factory-setting. ALL CLEAR Execute all the (1) (2) and (3) together at the same time.

~40—

Page 43

Press the PI button switch | to execute the selected item.

HA Doeither one of the following procedure to return to the test menu screen.

¢ Press the P1 start switch.

  • Hit the P1 4-direction joystick up or down to select “CANCEL” on the screen and then press the P1 button switch 1.

Pl 4-direction P1 button switch Pl start switch joystick zS %® S22 «os

Perform “6-1-3 Finishing the Test Mode” (p.24) to exit the test mode.

Page 44

7, OPERATION

A WARNING :

@ Should any off-flavor or noise occur, turn OFF the power switch of the cabinet immediately and stop operation. Then unplug the power cord from an electrical outlet and contact your distributor. If the machine is kept operating without solving the trouble, it may cause an electrical shock or fire. @ If you have to touch the PC board during operation, refer to “8. INSPECTION & CLEANING, TROUBLESHOOTING” on p.45. @ Make sure that installing and connecting were conducted in accordance with the instructions and the procedure specified in this operation manual (Ref. “5. Installing and Connecting” on p.9) before operation. Otherwise it may cause a fire, electrical shock or machine trouble.

7-1 Persons Not Recommended to Play A\ CAUTION : @ To ensure the safety of players, those who

  • are not feeling well;
  • are injured on the arms or hands;
  • are under the influence of alcohol;

are not recommended to play this game.

7-2 Restrictions When Operated A\ WARNING : @ This product is designed for indoor use only. Do not operate this product outdoors. It may cause a fire or electrical shock.

TACHI @ Observe the restrictions described under “2. SPECIFICATIONS” on p.6. Otherwise it may cause breakdown or malfunction.

@ Do not operate this product in areas:

  • with direct water contact;
  • with high humidity;
  • with much dust;
  • near heating systems;
  • where a drastic change in temperature might cause dew condensation;
  • subject to vibration;
  • near inflammable or volatile substance;
  • near strong magnetism or radio source. It may cause breakdown or malfunction.
Page 45

7-3 How to Play How to play the game and various techniques to be used are printed on A sticker, B sticker, and the title sheet.

~43—

Page 46

8. INSPECTION & CLEANING, TROUBLESHOOTING

  • To be serviced by a qualified service technician only —

8-1 Inspection & Cleaning Av WARNING : @ Unplug the power cord of the cabinet from an electrical outlet before conducting inspection or cleaning. Otherwise an electrical shock may happen. @ Do not conduct any works with wet hands. It may cause an electrical shock.

Be sure to conduct a regular inspection and cleaning according to the following table so that the “Mr. DRILLER” game is played in good condition. [- Time Description Reference Notes | Check that the PC board is fixed and connected | 5. INSTALLING To be serviced firmly. It might loosen due to the vibration during | AND CONNECTING | by a qualified

the game play, and the operation in such(p.9)service

conditions may cause breakdown or malfunction. technician only. Every month 9 |-z----202---vvv nooner nzoo nt rmeronennnmmnrman -

Check that the cabinet, harness, cables do not5. INSTALLINGTo be serviced

touch the PC board. If operated with such contact |AND CONNECTING [by a qualified

5conditions, it may cause breakdown or(p.9)service
3malfunction.technician only.
aTest the display, switches, and sound.6-2 DISPLAY TEST

5 (p.24) & 6-3 SWITCH TEST % (p.32) 6-4 SOUND TEST Every six months (p.33)

Clean the PC board. A foreign substance or dust To be serviced on the PC board may cause breakdown or by a qualified malfunction. service technician only.

(Aes @ A service technician should not be charged electricity when touching the PC board. Static electricity may cause the product breakdown or damage. @ Clean the product using a static-electricity-free cleaning equipment such as a brush for an OA equipment. The IC on the PC board may be damaged by static electricity and will not function correctly. @ Do notclean the product using the liquid such as water or detergent. Otherwise it may cause the product breakdown or damage. @ Do not attempt to perform conductivity test using a multi-meter. The IC of the PC board may be damaged even by the internal voltage of a multi-meter, and may not function correctly. @ Do not replace the built-in batteries. Otherwise breakdown or damage of the product may happen.

Page 47

8-2. Troubleshooting man WARNING : @ Always unplug the power cord of the cabinet from an electrical outlet before checking this product is installed and connected on the cabinet correctly. Otherwise an electrical shock may occur.

@ Should any off-flavor or noise occur, turn OFF the power switch of the cabinet immediately and stop operation. Then unplug the power cord from an electrical outlet and contact your distributor. If the machine is kept operating without solving the trouble, it may cause an electrical shock or fire.

CMehi=w @ Do not replace the built-in batteries. Otherwise breakdown or damage of the product may happen.

When this product does not operate correctly or has any trouble, check it in the following procedure. Turn OFF the power switch of the cabinet, and unplug the power cord from an electrical outlet. Remove any foreign substance or dust on the PC board.

(aNehessy @ A service technician should not be charged electricity when touching the PC board. Static electricity may cause the product breakdown or damage. @ Clean the product using a static-electricity-free cleaning equipment such as a brush for an OA equipment. The IC on the PC board may be damaged by static electricity and will not function correctly.

Check again that this product is installed and connected correctly to the cabinet. (Refer to the operation manual of the cabinet and “5. INSTALLING AND CONNECTING?” (p.9 - 19) on this operation manual.)

(Mehra @ Do not attempt to perform conductivity test using a multi-meter. The IC of the PC board may be damaged even by the internal voltage of a multi-meter, and may not function correctly.

Plug the power cord into an electrical outlet, and turn ON the power switch of the cabinet. Check again that adjustment is made correctly. (Refer to “6. ADJUSTMENT FOR OPERATION” (p.20 - 41) on this manual.

Page 48

When the trouble is not solved even after performing the procedure from Ml through @, turn the power OFF, unplug the power cord from an electrical outlet, and contact your distributor.

~46—

Page 49

9. Disassembling, Safekeeping, Transportation

9-1 Disassembling -To be serviced by a qualified service technician only —

Av WARNING : @ Be sure to unplug the power cord from the electrical outlet before conducting any works. Otherwise it may cause an electrical shock.

@ A service technician should not be charged electricity when touching the PC board. Static electricity may cause the product breakdown or damage.

Disassemble the PC board following the procedure below. Prepare the operation manual of the cabinet at hand.

Turn the power of the cabinet OFF and unplug the power cord from an electric outlet.

Open the door of the storage of the PC board in accordance with the operation manual of the cabinet and take out the install board on which the PC board is installed.

Page 50

Disconnect the cables and harnesses connecting to the PC board.

i ——_ a

/

EX Remove the screws on the four comers of the PC board and disassemble the PC board from the

install board.

Put back the install board and close the door.

Page 51

9-2

Safekeeping

After disassembled, pack this product with the packing materials attached to the product or conductive sponges and aircaps, and then keep it in a dry place with no dust. Do not put heavy stuff on it.

@ Do not keep this product in areas,

  • where exposed to direct sunlight.
  • with direct water contact -. with high humidity
  • with much dust
  • near heating systems
  • where a drastic change in temperature might cause dew condensation
  • with vibration
  • near inflammable substances or volatile substances.

Otherwise it may cause breakdown.

Transportation

When transporting this product for transfer, resale or repair, pack this product with the packing materials attached to the product, or conductive sponges or aircaps, and put it in a cardboard carton.

~49—

Page 52
  • DISPOSAL

Av WARNING : @ Do not throw this product into a fire. Otherwise it may cause an explosion of lithium batteries used in the product and cause injury. @ When disposing this product, collect, transport and scrap it in accordance with law and orders.

@ If entrusting others to collect, transport and scrap this product, hire specialists in each of such work.

~50—

Page 53
  • REPLACEMENT PARTS LIST

The following parts are provided as replacement parts for this product.

Contact your distributor for inquiries on the replacement parts.

Model number Parts No.

Title sheet 499-153

A sticker 499-154 B sticker 499-155 Mr. DRILLER2 499-152 PC Board Operation Manual Extended stereo sound connector (EI4P) 499-156

—~51-

Page 54

©NAMCO LIMITED

First edition is issued in July 2000

@ The specifications and this operation manual are subject to change without notice.