Bally Midways MCR II System Games (M051-0986-A025)
MCR II System Games (Bally/Midway, 1983) · Manual · 60 pages · 36 sections · original scan
MCR Il System Games
Bally/Midway’s [|
ee Se ee ee ee ee
WARNING
THIS GAME MUST BE GROUNDED. FAILURE TO DO SO MAY RESULT IN DESTRUCTION TO ELECTRONIC COMPONENTS.
- ina commerical environment. Operation of this equipment in a residential area ts likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.
ELECTRICAL BULLETIN: FOR ALL APPARATUS COVERED BY THE CANADIAN STANDARDS ASSOCIATION (CSA) STANDARD C22.2 NO. 1, WHICH EMPLOYS A SUPPLY CORD TERMINATED WITH A POLARIZED 2-PRONG ATTACHMENT PLUG.
See BLADES CAN BE FULLY INSERTED TO PREVENT BLADE
EXP! 5 ATTENTION: POUR PREVENIR CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR. UNE PRISE DE COURANT OU_UNE AUTRE SORTIE DE COURANT, SAUF Si LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT.
Cally Mipway Ipiles You Ta Use
OUR TOLL FREE NUMBERS FOR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER BALLY/MIDWAY™ GAME YOU NOW HAVE ON LOCATION.
CALL US FOR PROMPT, COURTEOUS ANSWERS TO YOUR PROBLEMS
ANSWERS TO YOUR PROBLEMS.
Continental U.S. 800-323-7182 Illinois Only 1-800-942-0497
© COPYRIGHT MCMLXXxXIII BY BALLY/MIDWAY CO. ALL RIGHTS RESERVED. NO PART OF THIS PUBLICATION MAY BE REPRODUCED BY ANY MECHANICAL, PHOTOGRAPHIC, OR ELECTRONIC PROCESS, OR IN THE FORM OF A PHONOGRAPHIC RECORDING, NOR MAY IT BE TRANSMITTED, OR OTHERWISE COPIED FOR PUBLIC OR PRIVATE USE, WITHOUT PERMISSION FROM THE PUBLISHER. THIS MANUAL IS FOR SERVICE USE ONLY, AND NOT FOR GENERAL DISTRIBUTION. FOR PERMISSION REQUESTS, WRITE: MIDWAY MFG. CO., 10750 W. GRAND AVE., FRANKLIN PARK, IL 60131 Printed in U.S.A.
DESCRIPTION
Vi. TABLE OF CONTENTS
Location and Setup ... Inspection... Installation Self-Test ..... Game Volume Adjustment Control Option Settings
Gelf-Test Mode... 0... ccc cece eee teen nee e Ett eet e En nnn tees 2-1
Maintenance and Repair... Cleaning ......... Fuse Replacement Opening the Control Panel Removal of the Main Display ‘Glass & T.V. Bezel TV. Monitor Replacement........... Printed Circuit Board Replacement Opening the Attraction Panel .... Servicing the Control Panel Black Light (Uprig
Technical Troubleshooting .. . Introduction . General Suggestions .. Harness Component Troubleshooting Transformer and Line Voltage Problems . A Glossary of Microprocessor Terms . . Introduction to the Z80 CPU. General Purpose Registers Arithmetic and Logic Unit (ALU) * Introduction Register and CPU Centro Z80 CPU Pin Description ............. MCR II System P.C, Board Jumper Options.
Coin Door Maintenance Metal Coin Acceptor Mechanisms . Plastic Coin Acceptor Mechanisms.
TV. Monitor Manual ..... 6.2... 006 cece cee ene tect ett n ete n eee tenes 6-1 Introduction oe Symptom Diagnosis... Guide to Schematic Symbols Troubleshooting....... Theory of Operation... Differences Between Monitors . Controls You May Not Touch Parts Interchangeability ... Picture Tube Interchangeability Wells Gardner Monitor Schematic -— 19” . Wells Gardner Monitor Replacement Parts List Electrohome Monitor Schematic — 19”...... Electronome Monitor Replacement Parts List Electronome Monitor Schematic — 13”.... Electrohome Monitor Replacement Parts List Zenith Monitor —- Sweep Board Schematic Zenith Monitor — Sweep Board Replacement Parts Zenith Monitor Main Board Schematic ............. Zenith Monitor Main Board Replacement Parts List ... Zenith Monitor — CRT Socket Board Replacement Parts List Zenith Monitor — CRT Socket Board Schematic . Zenith Monitor Width Step Assy. Schematic ... Zenith Monitor Interconnect for Video Game Sc
TABLE OF FIGURES
FIGURE PAGE
1-1 Location of Serial No., Interlock Switch, On/Off Switch, and Major Sub-Assemblies ..... 1-2 1-2 Major Sub-Assemblies (Cont. from Fig. 1-1) . . 1-3 1-3 interlock Switch Operation .. . 1-3 1-4 Location of Volume Control . . 1-4 1-5 Location of Option Switches. . 1-4 1-6 Option Switch Settings .... 1-5 2-1 Self-Test — Menue.... . 2-4 2-1a Self-Test — Sounds . . 2-2 2-1b Self-Test — Player Inputs . 2-2 2-1c Self-Test — Bookkeeping . 2-2 2-1d Self-Test — Time Report 1 2-2 2-1e Self-Test — Score Report.. . 2-3, 2-1f Self-Test — Set-Up Options . . 2-3 2-1g Self-Test — Channel Test.... . 2-3 2-2 Location of Hardware Master Reset Switch . 2-4 3-1 Location of Fuses .......-.-.--se seer eee . 34 3-2 Opening the Control Panel — Upright & Mi . 3-2 3-3. Opening the Cocktail Game ............ . 3-3 3-4 Removing the Control Panel — Cocktail. . 33 3-5 Removing the Main Display Glass & T.V. Bezel — Upright . . 3-4 3-6 Removing the Main Display Glass & T.V. Bezel — Mini 3-4 3-7. Removing the Top Glass & T.V. Bezel — Mini........... . 3-5 3-8 Removing the Monitor — Upright ... . 3-6 3-9 Removing the Monitor — Mini . 36 3-10 Opening the Cocktail Game .. . 3-7 3-11 Removing the Monitor — Cocktail . 37 3-12 Removing P.C.B.’s...........665 . 3-8 3-13 Removing P.C.B.'s from Card Rack.. . 3-9 3-14. Opening the Attraction Panel — Uprig . 3-10 3-15 Replacing Fluorescent Light Fixture... . 3-11 3-16 Opening the Attraction Panel — Mini . 3-11 3-17 Servicing Control Panel Black Light — Upright . . 3-12 3-18 Removing Black Light Tube Mtg. Brkt. — Upright. . 3-12 5-1 Removing and Replacing the Coin Acceptor. 5-1 5-2 Cleaning the Metal Coin Acceptor .... . 5-2 5-3 Lubricating the Metal Coin Acceptor . 5-2 5-4 Opening the Plastic Coin Acceptor ... . 5-3 5-5 Changing the Plastic Coin Acceptor to Accept American or Canadian Quarters . » 5-4
I. Location and Setup
INSPECTION:
- Remove the game from its shipping crate.
- Inspect the entire outside of it for any signs of damage. O Any scratches?, dents?, cracks? O Any broken controls? @ Any broken glass or plastic? © Just look it over closely and make a note of any signs of damage.
- Remove the shipping cleats from the bottom of the cabinet. 4, Install the four levelers, one at each corner of the cabinet. C Level the cabinet.
- Open the cabinet and inspect the inside of the game for any signs of damage. See Figure 1-1. O Also check to make sure all plug-in connectors on the wire harness are firmly seated.
O Replug any connectors found unplugged. DO NOT FORCE PLUGS ONTO CONNECTORS. DO NOT FORCE PLUGS TOGETHER. If it won't go on easily, assuming the keys are lined up, it either does not belong there or is damaged. O Make sure all printed circuit boards (P.C.B.'s) are firmly seated in their connectors. These connectors are also keyed. The P.C.B.'s will only go into them one way without being damaged.
- Call your distributor and/or service man about your problem list. INSTALLATION:
- Location requirements: O Power: Domestic 110 V @ 60 Hz Foreign 200 V to 240 V @ 50 Hz O Temperature: 32° to 100°F (0° to 38°C) O Humidity: Not over 95% relative 0 Space required: Upright 25" x 32” (63 x 81cm) APPROX. Mini 20" x 24” (50 x 60cm) Cocktail 32” x 22” (81 x 55cm) O Game height. Upright 70" (175cm) APPROX. Mini 61" (153cm) Cocktail 29" (73cm)
. Voltage Selection: Your game is designed to work properly on the line voltage where you are located. Check your line voltage with a meter to determine what its value is. Then check the power input wires to the main power supply transformer on your game to be sure they are connected to taps which correspond to your line voltage value. If the power input wires to the main power supply transformer are not connected to taps which correspond to your local line voltage, move them to the proper taps.
If the line voltage in your area falls outside the upper or lower limits of the range of inputs covered by the main power supply transformer, DO NOT PLUG YOUR GAME IN until you have talked with your distributor and/or service man and obtained a solution to this problem. Otherwise you could damage your game.
. Interlock and power ON/OFF switches. See Figure 1-1. 0 To help prevent the possibility of getting an electric shock while working inside the game cabinet, interlock switches have been installed at each cabinet access door (this DOES NOT include the coin door in the Upright and Mini models). O When any access door is opened, the interlock switch installed there turns off all power to the game.
SERIAL NUMBER
ON/OFF maar SWITCH NUMBER Tv. MONITOR
INTERLOCK SWITCH
Te POWER SUPPLY || PC.B. i INTERLOCK SWITCH
(NOT SEEN) POWER SUPPLY P.C.B.
ON/OFF SWITCH
Ty. MONITOR
POWER SUPPLY CHASSIS SERIAL NUMBER (MAY BE LOCATED ON ANY CORNER) POWER SUPPLY P.C.B. LoGic BOARDS.
CONTROL PANEL (PLAYER 2) CONTROL PANEL (PLAYER 1)
ON/OFF SWITCH UNDER TABLE ON PLAYER 2 SIDE INTERLOCK SWITCH (INSIDE DOOR) COCKTAIL
Figure 1-1 Location of Serial No., Interlock Switch, On/Off Switch, & Major Sub-Assemblies
1-2
UPRIGHT CONTROL PANEL
Figure 1-2 Major Sub-Assemblies (cont. from Fig. 1-1)
O Check each Operation. After checking the line voltage in your area and determining that the input wires to the main power supply transformer of your game are connected properly — or — after obtaining a solution to your over or under voltage problem from your distributor and/or your service man, plug the game into your A.C. wall outlet. The game ON/OFF switches for all models are located as shown in Figure 1-1. Turn the game on and allow it to warm up a few minutes. Slowly open each access door to the game (this does not inciude the coin door on the Upright and Mini models). As the door is opened approximately 1” (2.54cm) the power to the game should go off (the T.V. monitor, all the lights, and all sounds will stop). If this does not happen, check the interlock switch by this door to see if it has broken loose from its mounting or if it is stuck in the “ON” Position. If the switch is found to be bad, turn the game off, unplug it, and replace the interlock switch. When done, plug the game back into the wail outlet, close the access door, and turn thegame back on. interlock switch for proper
1-3 After the game has warmed up, repeat the above interlock switch test.
When the interlock switch is working properly and turns the power to the game off, power may be restored to the game with the access door(s) open. Take hold of the interlock switch plunger and gently pull it out to its fully extended position. THIS IS TO BE USED ONLY FOR SERVICING THE GAME. See Figure 1-3.
Figure 1-3 Interlock Switch Operation
SELF-TEST: Your new game will Self-Test itself to see if it has any bad parts. The information it receives while testing itself will be shown on the T.V. monitor. See the SELF- TEST section for a more detailed description of this function. When there is a bad result according to the Self-Test, call your distributor and/or service man to have the trouble fixed unless it is something you can do yourself (such as replace a bad RAM or ROM chip).
GAME VOLUME ADJUSTMENT CONTROL: See Figure 1-4. The game volume control pot is located just inside the cabinet coin door frame. There is only one pot. For adjustment, it may be reached through the coin door on ALL models. To make the sounds louder, turn the pots clockwise as you face them (7). To make the sounds less loud, turn the pots counterclockwise as you face them (A ).
OPTION SETTINGS: To change the most common option settings, you DO NOT have to take the game apart or go into the cabinet and hunt for tiny switches on P.C. boards. These most common options can be changed from the main console of the game while it is in the Self- Test mode. The Self-Test switch is located just inside the cabinet coin door frame as you face it. When changing any options, ALWAYS perform the Self-Test and play the game to be sure the ones selected are working properly. Of course, when you
OPTION SWITCH 3 SERVICE CREDIT SWITCH
SELF-TEST SWITCH
VOLUME ADJUSTMENT
Figure 1-4 Location of Volume Control
must change one of the switches that is located on one of the game's P.C. boards, it is also recommended that you perform the Self-Test and play the game to be sure the switches have worked properly and that no switches were accidentally moved that were not meant to be. (These switches are small and this can happen.) The P.C. Board option switch settings, and what they will make the game do are shown in Figure 1-6. These switches are MAINLY INTENDED for use by a technician who is checking and/or performing tests on the game. See Figure 1-5 for option switch locations.
OPTION SWITCH 1
Figure 1-5 Location of Option Switches
Il. Self-Test Mode
The Self-Test mode is a special mode for checking game play statistics as well as game switches and computer functions. It is the easiest and best way to check for proper operation of the entire game.
- If the game is in the Attract mode when the Self- Test switch is moved to the “ON” position, it will finish the sequence and then go into the Self-Test mode. This is illustrated by the display of the Self- Test Mode Menue on the monitor screen. . If the game is in the Ready-To-Play mode or the Play mode when the Self-Test switch is slid to the “ON” position, it WILL NOT go into the Self-Test mode until AFTER the game is over. At this point, the game will go into the Self-Test mode. Again, this is illustrated by the display of the Self-Test Mode Menue on the monitor screen. . The fastest way to enter the Self-Test mode is to slide the Self-Test switch to the “ON” position and then activate the “TILT” switch located on the back side of the coin door just below the lock mechanism. The game will then IMMEDIATELY go into the Self-Test mode. The Self-Test mode has eight (8) major categories as illustrated by Figure 2-1.
- Itis easy to select what category you want to enter. By following the ON SCREEN instructions, the Cursor at the left of the screen can be moved UP or DOWN until it is in front of the category you want to test. . After the Cursor has been positioned, follow the ON SCREEN instructions again, and the monitor screen will display the test category you have selected.
- including ALL information in the “BOOKKEEP- ING” mode, and ALL operator selected options, will be set back to zero (“0”) and to the factory recommended settings — respectively.
2-1 SELECT DESIRED TEST
1 SELF DIAGNOSTICS 2 SOUNDS 3 PLAYER INPUT 4 BOOKKEEPING 5 MACHINE SETUP 6 CHANNEL TEST 7 PRESET 8 GRID DISPLAY
POSITION CURSOR BY ....
Figure 2-1 Self-Test — Menue
O Once you are IN one of the Self-Test mode categories, FOLLOW THE ON-SCREEN IN- STRUCTIONS TO COMPLETE THE TEST.
- The next group of Figures show the CORRECT screen presentation for EACH category of the Self-Test mode. During the SELF DIAGNOSTICS section of the Self-Test mode, you will first see a cross hatch pattern on the screen for about 1/2 second. Second, you will see a lot of different colored bars shown on the monitor screen. These bars will be UNpainted one at a time from the top down. Third, you will see the screen painted Red, Blue, and Green in bars from the top down. Fourth, all the different colored bars you saw “Second” are displayed again. And fifth, the different coiored bars are replaced by an exit message. If you do not exit, the test will repeat itself. This feature was designed into the game to enable over-night testing for an intermittent hardware problem. \f the SELF DIAGNOSTICS find one or more bad ROM or RAM chips: instead of going through what is described above, the game will give you a written message as to which parts are bad. This message includes their I.D.’s and their P.C. Board locations.
During the SOUNDS section of the Self-Test mode, the game will give a display which looks like that shown in Figure 2-1a. O In this category, each of the game's separate sounds can be checked individually in any order — or — you can tell the game to check them all in order. During the PLAYER INPUT section of the Self-Test mode, the game will give a display which looks like that shown in Figure 2-1b. O In this category, each of the game's player operated controls — including the coin switches on the back side of the coin door — may be checked individually. A game sound will be heard as each switch/control is actuated. If no game
SELECT A SOUND
- ALL SOUNDS
REMAINDER OF GAME SOUNDS CALLED OUT IN ORDER
POSITION CURSOR BY...
Figure 2-1a Self-Test — Sounds
PLAYER INPUTS
PLT FIRE
As the Player input Switches and Devices are activated, he Switch. or Device. activated. i¢ spelled out in: the ‘space indicated.
MIN! UPRIGHT 1 COIN METER
ACTIVATE ALL PLAYER INPUT
SWITCHES AND DEVICES HIT TILT 10 EXIT
Figure 2-1b Self-Test — Player Inputs
2-2 sound is heard, that switch/control is either not working, miswired, or disconnected. Check it out thoroughly. During the BOOKKEEPING section of the Self-Test mode, the game will give a display which looks like that shown in Figure 2-1c. O In this category a basic bookkeeping function is performed. And with the selection of the “TIME REPORT” and the “SCORE REPORT”, detailed breakdowns of game times and scores may be obtained. In the TIME REPORT and SCORE REPORT sections of the BOOKKEEPING mode, the game will give displays which look like those shown in Figures 2-1d and 2-1e respectively.
SELECT A REPORT OR EXIT. CHUTE 1 COINS CHUTE 2 COINS LONGEST GAME SHORTEST GAME HIGHEST SCORE 05 18 00 43 86310 LOWEST SCORE 120 TIME REPORT SCORE REPORT. EXIT.
POSITION CURSOR BY...
Figure 2-1c Self-Test — Bookkeeping
TIME REPORT 0 1030. SEC 30 7060 SEC 60.1090 SEC 90 T0 120 SEC 120 T0 158 SEC 150 T0 180 SEC 3.704 MIN 4705 MIN 5 70 6 MIN OVER 6 MIN
Figure 2-1d Self-Test — Time Report
___ SCORE REPORT 070 5000 PTS - 5000 TO 10000 PTS 10000 T0 20000 PTS 20000 TO 40000 PTS 40000 TO 70000 PTS 70000 TO 100000 PTS 10000010 150000 PTS 150000 T0 200000 PTS 200000 T0 250000 PTS OVER 250000 PTS
Figure 2-1e Self-Test — Score Report
During the SETUP OPTIONS section oi the Self-Test
mode, the game will give a display which looks similar to that shown in Figure 2-1f. C1 In this category, all common game options may be changed from the control console: coins per credit, credits per base, bonus base(s) awarded at, difficulty level - -, and so on.
SETUP OPTIONS
COIN CHUTE 1 *T COINS FOR “T CREDITS
COIN CHUTE 2 “T COINS FOR “T GREDITS
*T CREDITS FOR *3 BASES 1ST EXTRA BASE AT *20000 POINTS
ADDITIONAL BASE EVERY *20000 POINTS
*3 DIFFICULTY LEVEL = Factory recommended settings. Figure 2-1f Self-Test — Set-Up Options
DIFFICULTY LEVEL EXPLANATION: The Difficulty Level setting has a range of 1 to 9. With 1 being the easiest level of play and 9 being the most difficult level of play. We recommend that a setting of 3 be used as a beginning point.
2-3 Game play can then be made MORE difficult or LESS. difficult, according to the skill levels attained by the players in your area. CHANNEL TEST: During the CHANNEL TEST section of the Self-Test mode, the game will give a display which looks like that shown in Figure 2-1g. C In this category, the game conducts a test of its SOUND SYSTEM. Once you enter the CHANNEL TEST section of the Self-Test mode, the game automatically tests Channels 1 through 6 giving a tone for each one as it checks it. After the 6th Channel is tested, the game automatically repeats the test until exited. \t then goes back to the Selt-Test Mode Menue. During the GRID DISPLAY section of the Self-Test mode, the game shows a white cross hatch pattern on the monitor screen. This is for alignment and/or test purposes. This pattern will remain on the monitor screen until exited. The game will then go back to the Self-Test Mode Menue. To leave the Self-Test mode, simply slide the Self-Test switch to the “OFF” position at ANY time. The game will then run through the ROM/RAM test display after which normal game functions will return to the monitor screen.
CHANNEL TEST GHANNEL 1 CHANNEL 2 CHANNEL 3 CHANNEL 4
CHANNEL 5
CHANNEL 6
Figure 2-1g Self-Test — Channel Test
RACK ADVANCE: The game can be made to advance through the various racks by beginning a game and THEN sliding the Self-Test switch to the “ON” position. After this has been done, each time you depress the ONE PLAYER BUTTON the game will advance one rack. When you reach the desired rack, slide the Self-Test switch to the “OFF” position. (If you leave the Self- Test switch in the “ON” position, the game will go into the Self-Test mode when you are finished playing.)
CROSS HATCH PATTERN: A cross hatch pattern is shown on the screen when power is first turned on to the game, when the TILT Switch is actuated, and during the “SELF DIAGNOS- TIC” portion of the Self-Test mode, and during the “GRID DISPLAY” portion of the Self-Test mode. This pattern may be kept on the screen for adjustment purposes as described earlier. When you are finished using the cross hatch pattern, simply exit at the GRID DISPLAY to return to the Self- Test Mode Menue. HARDWARE MASTER RESET SWITCH: There are two of these little red switches, one on the Sound I/O Board and one on the CPU Board, located as shown in Figure 2-2. The function of each of these switches — when pressed — is to make the game think it has JUST been turned on. They set up an “initial power-up” condition. We DO NOT recommend that you indiscriminately press EITHER of these switches. They should ONLY be used if there is a major problem encountered while testing the P.C. Boards.
HARDWARE MASTER RESET SWITCH
Figure 2-2 Location of Hardware Master Reset Switch
Ill. Maintenance and Repair
Your NEW game needs certain types of maintenance to keep it in good working order. CLEAN, well MAINTAINED games attract players and EARN MORE PROFITS. The most important thing for you to remember is to run the Self-Test EVERY TIME you collect money from the coin box. JUST LOOKING at your game WILL NOT tell you if all its controls and inside parts are working correctly. The Self-Test will inform you whether or not your game is working the way it should. The second most important thing you should remember is to clean the outside of the game and coin acceptor mechanisms on a regular basis. CLEANING The outside of the game cabinet plus the metal can be cleaned with any non-abrasive household cleaner. However, the front of the T.V. monitor tube and both sides of all other glass and plastic on or in the game MUST be cleaned with anti-static cleaner ONLY. For cleaning the coin acceptors: hot soapy water may be used on the plastic ones and any househoid cleanser may be used on the metal ones. If you wish, special coin machine cleaners that leave no residue may be purchased from your distributor. DO NOT dry-wipe any of the plastic panels. This is because any dust that was on them can scratch their surfaces. If this has happened, anyone looking through this type of damaged plastic would feel he was looking at the game through a fog. This fogging damage CANNOT be repaired or reversed. The ONLY solution is to replace the damaged piece of plastic.
FUSE REPLACEMENT This game contains several fuses located as shown in Figure 3-1.
- UPRIGHT MODEL: As viewed from the back, facing the cabinet, with the rear access door removed; the fuses are located on the Power Supply Chassis and Power Supply P.C. Board.
- MINI MODEL: As viewed from the back, facing the cabinet, with the rear access door removed; the fuses are located on the Power Supply Chassis and Power Supply P.C. Board.
- COCKTAIL TABLE MODEL: As viewed from the coin door side of the cabinet, with the monitor tilted open to one side; the fuses are located on the Power Supply Chassis and the Power Supply P.C. Board. Replace fuses ONLY with the type and size listed in the Illustrated Parts Breakdown Section of your game manual. See the T.V. Monitor Manual (available on request from your distributor or the monitor manufacturer) and/or the T.V. Troubleshooting Section of your game manual for information on these fuses.
FUSES LOCATED ON POWER SUPPLY BOARD AND POWER SUPPLY CHASSIS
Figure 3-1 Location of Fuses
3-1
OPENING THE CONTROL PANEL 1, UPRIGHT MODEL: See Figure 3-2. O The contro! panel is held in place by two or three
- MINI MODEL: See Figure 3-2. O The control panel is held in place by two latches, latches, one on the left side and one on the right side of the cabinet. They are spring loaded to provide constant positive pressure on their latch plates. They can be reached through the coin door AFTER turning power to the game off. To release the latches, lift up and toward the front center of the contro! panel. Once they are released, unhook them from their latch plates. C To remove the control panel: Raise it up and tilt it toward you until you can see the cabie behind it. Cradling the control panel between yourself and the cabinet, disconnect it from its cabling and nylon retaining strap. The control panel is now free and can be removed. O To reinstall the control panel, reverse this procedure. one on the right side, and one on the left side of the cabinet. They are spring loaded to provide constant positive pressure on their latch plates. They can be reached through the coin door AFTER turning power to the game off. To release the latches, lift up and toward the center of the control panel. Once they are released, unhook them from their latch plates. O To remove the control panel: Raise it up and tilt ittoward you until you can see the cable behind it. Cradling the control panel between yourself and the cabinet, disconnect it from its cabling and nyion retaining strap. The control panel is now free and can be removed. O To reinstall the contro! panel, reverse this procedure.
UPRIGHT
Figure 3-2 Opening the Control Panel — Upright & Mini
CLAMPS
Figure 3-3 Opening the Cocktail Game
- COCKTAIL TABLE MODEL: See Figure 3-4. O Each ‘contro! panel is held in place by several screws, two on the inside of the cabinet and three along the outside bottom edge of the control panel. Turn power to the game off. Open the coin box door and release the two latches indicated in Figure 3-3.
CAUTIO! he right hand latch is very close to the HIGH VOLTAGE on the monitor. BE CAREFUL!
Once they're released, unhook them from their latch plates. Grasp the table top at “A” and open it as indicated in Figure 3-3.
Remove the screws which secure the control panel in place. See Figure 3-4. O To remove the control panel(s): Disconnect it from its cabling. The control panel is now free and can be removed.
OQ To reinstall the contro! panel, reverse this procedure. LiFT CONTROL UP
REMOVE
- SCREWS EACH SIDE
REMOVE(3) SCREWS
Figure 3-4 Removing the Control Panel — Cocktail
REMOVAL OF THE MAIN-DISPLAY-GLASS AND/OR THE TV. BEZEL ASSEMBLY 2. MINI MODEL: See Figure 3-6. . 7 NOTE: In order to do this, the control panel MUST
1, UPRIGHT MODEL: ie Figure 3-5. be removed first. See above “Mini Model"
DISPLAY GLASS
GLASS CLAMPING PLATE DISPLAY GLASS
GLASS CLAMPING PLATE (CERTAIN MODELS)
Figure 3-5 Removing the Main Display Glass & T.V. Figure 3-6 Removing the Main Display Glass & T.V. Bezel — Upright Bezel — Mini
3-4
- COCKTAIL TABLE MODEL: See Figure 3-7.
Figure 3-7 Removing the Top Glass & T.V. Bezel
- Mini T.V. MONITOR REPLACEMENT
- UPRIGHT MODEL: See Figure 3-8. O Turn power off to the game. © Open the rear access door. O Completely disconnect the T.V. monitor from all its cabling. DON’T FORGET THE CHASSIS GROUND WIRE. O Before removing the T.V. monitor, the maindisplay-glass and bezel must be removed. See above “Upright Model” procedure. O With the removai of only four bolts, the T.V. monitor and its mounting bracket will be loose. C The monitor mounting bracket slides on top of and against two metal guides mounted to the cabinet’s right and left sides. The monitor is removed by sliding it out the back of the cabinet. “Q1To reinstall the T.V. monitor, reverse this procedure. O After replacing the T.V. monitor, be sure to run the game Self-Test.
- MINI MODEL: See Figure 3-9. C Turn the power off to the game. CO Open the rear access door. O Completely disconnect the T.V. monitor from all its cabling. DON’T FORGET THE CHASSIS GROUND WIRE. D Before removing the T.V. monitor, the maindisplay-glass and bezel MUST be removed. See above “Mini Model” procedure. O With the remova! of only four bolts, the T.V. monitor will be loose.
3-5
O The monitor is removed by supporting it and pulling straight back. (BE CAREFUL not to hit monitor on its rear support bracket.) O To reinstall the T.V. monitor, reverse this procedure. O After replacing the T.V. monitor, be sure to run the game Self-Test.
- COCKTAIL TABLE MODEL: See Figure 3-11. O Turn the power off to the game.
O Open the coin box door and release the two latches indicated in Figure 3-10.
REMOVE (4) BOLTS
Figure 3-8 Removing the Monitor — Upright
O Once the latches are released, unhook them from their latch plates. O Grasp the table top at “A” and open it as indicated in Figure 3-10.
REMOVE (4) BOLTS
Figure 3-9 Removing the Monitor — Mini
CLAMPS
Figure 3-10 Opening the Cocktail Game
O Remove the screws which hold the table top glass clamps in place. O Remove the table top glass. O Lift out the T.V. bezel assembly. O Completely disconnect the T.V. monitor from all its cabling. DON'T FORGET THE CHASSIS GROUND WIRE. O Remove the screws holding the T.V. monitor chassis to the “L” brackets by the door hinge(s). See Figure 3-11. O Close the Cocktail Table and re-latch it.
O Remove the screws which secure the T.V. monitor mounting brackets to the edges of the slot cut in the table top. See Figure 3-11. O Pry up the end of each monitor mounting bracket with a screwdriver or similar tool until you can grasp them both.
O Lift the T.V. monitor straight up and out of the table top being very careful not to bump the neck of the picture tube. O To reinstall the T.V. monitor assembly, reverse this procedure. Be sure to check the clearance of the “L” brackets BEFORE setting the monitor into the table top. O After replacing the T.V. monitor, be sure to run the game Self-Test. REMOVE 6 SCREWS (3 EACH SIDE) LIFT MONITOR STRAIGHT UP
REMOVE 4 SCREWS (2 EACH SIDE)
Figure 3-11 Removing the Monitor — Cocktail
PRINTED CIRCUIT BOARD (P.C.B.) REPLACEMENT
- UPRIGHT MODEL: See Figure 3-12. O Turn the power to the game off. O To reinstall the above P.C.B.’s, reverse this procedure. O Unlock and open the rear access door. O Dis +t all cabling from the P.C. boards and Wf thar Gat of thelr 3 =_— NOTE: P.C.B.'s are all keyed and wilt ONLY fit into lift them out of their card rack. . | their connectors one way without forcing them. O Disconnect the linear power supply board from The plugs on the cable harness which connect it to all its cabling, remove the P.C.B. supports indi- the P.C.B.’s are also keyed and will ONLY go onto cated in Figure 3-12, and slide the linear power their connectors one way without forcing them. supply board out the back of the cabinet.
REMOVE (2)
COCKTAIL REMOVE SUPPORT REMOVE SUPPORT
UPRIGHT
Figure 3-12 Removing P.C.B.’s
REMOVE SCREWS FROM SIDE OF CABINET TO REMOVE LOGIC BOARDS
Figure 3-13 Removing P.C.B.’s from Card Rack
- MINI MODEL: See Figure 3-12. O Turn the power off to the game. O Unlock and open the rear access door.
O Disconnect all cabling from the P.C. boards and lift them out of their card rack.
O Disconnect the linear power supply board from all its cabling, remove the P.C.B. supports indicated in Figure 3-12, and slide the linear power supply board out the back of the cabinet. O To reinstall the above P.C.B.’s, reverse this Procedure.
- COCKTAIL TABLE MODEL: See Figure 3-12. O Turn the power off to the game.
O Open the cabinet: Open the coin box door and release the two latches indicated in Figure 3-10.
O To remove the linear power supply board. See Figure 3-12. Disconnect it from all its cabling. Remove the two smallest P.C.B. supports. Once these are removed, the linear power supply can be lifted out the top of the cabinet. To reinstall the linear power supply board, reverse this procedure. 0 To remove the P.C. boards from the card rack. See Figure 3-13. Disconnect them from ALL their cabling. The P.C. boards are now free and can be slid from their rack. O To reinstall the P.C. boards, procedure. reverse this
OPENING THE ATTRACTION PANEL
- UPRIGHT MODEL: See Figure 3-14. O Turn the power to the game off. O Opening the attraction panel: Remove the screws which secure the top bracket in place. (They are on its top side.) See REMOVE SCREWS ON TOP AND LIFT ATTRACTION Figure 3-14. PANEL UP
Remove the top bracket and slide up the attraction panel. This exposes the attraction panel fluorescent light tube and its mounting bracket assembly, To reinstall the attraction panel, reverse this procedure. O The fluorescent light tube may be replaced at this time. BE CAREFUL NOT TO DROP IT.
O Replacing the fluorescent tube starter. See Figure 3-15. Be sure the power to the game has been turned off. Grasp the starter (it is on the back of the mounting bracket), give it a quarter turn, and remove it from its socket. To replace the fluorescent light tube starter, reverse this procedure.
Replacement of the fluorescent tube mounting bracket assembly. Be sure the power is off to the game.
Disconnect it from its power cable. Remove the screws at its right and left hand sides which secure it and gently slide it out of the front of the cabinet, being careful not to catch its power cable on anything. To reinstall the fluorescent tube mounting bracket assembly, reverse this procedure.
Replacing the speaker. Figure 3-14 Opening the Attraction Panel — Upright Be sure the power is off to the game. Remove the attraction panel and disconnect the speaker from its cabling. Remove the nuts and bolts which secure the speaker and speaker grill in place and set them and the speaker grill aside. Once the bolts which secure the speaker in place are removed, the speaker may be removed through the opening where the attrac-
- MINI MODEL. See Figure 3-16. O Turn the power off to the game.
O Remove the screws which secure the top bracket in place. (They are on its top side.) See Figure 3-16. O Remove the top bracket and slide up the attraction panel was. Reverse this procedure to reinstall the speaker.
3-10 tion panel. This exposes the attraction panel light bulbs and their mounting board.
—~ FLUORESCENT —— TUBE STARTER V4 x 1/4 TURN TO REPLACE
Figure 3-15 Replacing Fluorescent Tube Starter
C To service the light bulbs and their mounting
board: REMOVE TOP
Turn the power to the game back on so you can BRACKET AND see which bulbs are burnt out. SLIDE HEADER UP. Mark the burnt out bulbs and turn the power to the game back off again. To replace the burnt out bulbs, grasp them genily and pull straight out. The new bulbs are gently pushed into the empty sockets. To completely replace the light bulb mounting board: Open the cabinet rear access door and unpiug the mounting board from its power cable. Remove the screws that hold the mounting board to the cabinet. Gently slide the mounting board out the front of the cabinet being careful not to catch its cable on anything. To reinstall the above removed items, reverse this procedure. O To replace the speaker. Be sure the power is off to the game. Disconnect the speaker from its cabling. Remove the nuts and bolts securing the speaker. Slide the speaker out through the rear access door. To reinstall the speaker, simply reverse this procedure.
- THE COCKTAIL TABLE MODEL HAS NO BACK- LIT ATTRACTION PANEL. Figure 3-16 Opening the Attraction Panel — Mini
3-11
SERVICING THE CONTROL PANEL BLACK LIGHT (CERTAIN UPRIGHT MODELS ONLY)
- Be sure the power is off to the game.
- Remove the control panei as described previously, This exposes the bottom row of screws which secure the control panel support bracket and the black light protector in place. See Figure 3-17
- Remove all the screws which secure the above items in place and set them aside. O The black light tube may be replaced at this time by reaching through the space where the light protector was before you removed it.
IWARNING: If you drop a black light tube and it breaks, iT WILL IMPLODE! Shattered glass can fly six (6) feet or more from the implosion. Use’ care when replacing any black light tube.
4, Replacing the black light tube starter. See Figure 3-15,
O Remove the black light tube. O Remove the screws which secure the black light tube mounting bracket to the cabinet. See Figure 3-18. The mounting bracket is now loose and can be pulled out and slightly to one side until you can see the black light tube starter.
REMOVE THESE SCREWS O Grasp the starter (it is on the back of the mounting bracket), give it a quarter turn, and remove it from its socket. To replace the black light tube starter, reverse this procedure. . The black light tube mounting bracket assembly may be replaced at this time by simply disconnecting it from its power cable and removing it from the game. . To reinstall any of the above removed items, simply reverse this procedure.
REMOVE (3) SCREWS
Figure 3-18 Removing Black Light Tube Mtg. Brkt.
- Upright
BLACK LIGHT PROTECTOR
CONTROL PANEL SUPPORT BRACKET
Figure 3-17 Servicing Control Panel Black Light — Upright
IV. Technical Troubleshooting
Introduction
The most common problems occur in harness components such as the coin acceptor, player controls, interconnecting wiring, etc. The TV monitor and PCB computer cause their share of problems too, but not as much as the harness and its component parts. TV monitor troubleshooting will not be covered here because it is covered in that section of this manual.
As you already know, the PCB computer is a complex device with a number of different circuits. Some circuits remain basically the same among games, but overall there are a great many differences between them. PCB troubleshooting procedures, therefore, can be lengthy and will differ greatly among games. However, some basic Z-80 CPU information is involved in this section.
General Suggestions
The first step in any troubleshooting procedure is correctly identifying the malfunction’s symptoms. This includes not only the circuits or features malfunctioning, but also those still operational. A carefully trained eye will pick up other clues as well. For instance, a game in which the computer functions fail completely just after money was collected may have a quarter shorting the PCB traces. Often, an experienced troubleshooter will be able to spot the cause of the problem even before opening the cabinet. After all the clues are Carefully considered, the possible malfunctioning areas can be narrowed down to one or two good suspects. Those areas can be examined by a process of elimination until the cause of the malfunction is discovered.
Harness Component Troubleshooting
Typical problems falling in this category are coin and credit problems, power problems and failure of individual features. NO GAME CREDIT For example, your prospective player inserts his quarter and is not awarded a game. The first item to check is if the quarter is returned. If the quarter is returned, the malfunction most certainly lies in the coin acceptor itself. First, use a set of test coins (both old and new) to ascertain that the player’s coin is not undersize or underweight. If your test coins are also returned, coin acceptor servicing is indicated. Generally, the cause of this particular problem is a maladjusted magnet gate. Normally, this will mean slightly closing the magnet gate a little by turning the adjusting screw out a bit (see section on coin acceptor for more details). if the quarter is not returned and there is no game credit, the cause of the malfunction may be in one of several areas. First try operating the coin return button; if the coin is returned, the problem is most likely in the magnet gate. Enlarge the gap according to the coin acceptor service procedures. If this does not cure the problem, remove the coin acceptor, clean it and perform the major adjustment procedure. If the trapped coin is not returned when the wiper lever is actuated, you may have an acceptor jammed by a slug, gummed up with beer, a jammed coin chute, or mechanical failure of the acceptor mechanism. In this case, first check for the stug that will generally be trapped against the magnet. If so, simply remove the slug and test the acceptor. If the chute is blocked, remove the acceptor and remove the jammed coins. If there is actual failure of the acceptor, remove the unit and repair as indicated in the coin acceptor service procedures. If the coin is making its way through the acceptor (that is, falling into the coin box), yet there is still no game credit, you either have a mechanical failure of the coin switch or electrical failure of the coin and credit circuits. The first place to begin is by checking the coin switch. Most of these switches are the make/break variety of micro switch, which is checked by testing for continuity between the NO, NC, and C terminals. When not actuated, the NC and C terminals should be continuous and the NO terminal open. When operated, the NO and C terminals should close and the NC should be open. If the coin switch checks out, examine the connections to the terminals to make sure there is good contact. If necessary, use the continuity tester and check from the terminal lug on the switch to the associated PCB trace. This will tell you if there is a continuous line all the way to the credit circuit
If the coin switch wires do not check out, the problem is in the computer — most likely in the coin and credit circuitry. If you do get game credit when a coin is deposited, but the game will not start when the start switch is pressed, you may have a problem in the start switch, the interconnecting wiring or in the computer. First check the switch. If the switch is OK, proceed to check the wiring. Again, make sure you go from the terminal lug on the switch to the PCB trace. This way, you will check the terminal contact as well as PCB edge connector contact. If the wiring is continuous, proceed to check the PCB credit circuit. If not, check each section of the wiring, until the discontinuity is located. If the wiring is OK, the problem must lie in the computer.
Transformer and Line Voltage Problems
Your machine must have the correct line voltage to operate properly. If the line voltage drops too low, a circuit in the computer will disable game credit. The point at which the computer will fail to work will vary some from game to game, but no game will work on line voltage that drops below 105 VAC. Low line voltage may have many causes. Line voltage normally fluctuates a certain amount during the day as the total usage varies. Peak usage times occur mainly at dawn or dusk, so if your machine's malfunction seems to be related to the time of day, this may be a factor. A large load connected to the same line as the game (such as a large air conditioner or other device with an exceptionally large motor) may drop the line voltage significantly when starting up. This drop can result in an intermittent credit problem. In addition, poor connections in the location wiring, plug, or line cord may also cause a significant drop in power. Cold solder joints in the game's harness, especially in areas like the transformer connections, interlock switch, or fuse block, may also produce the same results, although probably on a more permanent basis. Sometimes location owners (especially in bars) replace light switches with dimmer rheostats, and the game is sometimes on the same line. Obviously, the voltage available to the game is going to drop dramatically when the dimmer is turned, In any case, the way to check for correct line voltage is with your VOM. Set the VOM to 250 VAC and stick the probes in the wall receptacle. If it’s OK here, check the transformer primary connections. If you do not get 117 VAC, examine the solder joints on the transformer, fuse block, and interlock switch. \f you do get 117 VAC, the problem must be either in the transformer, harness connections, or in the PCB power supply.
4-2 If you suspect the transformer, check itssecondaries with the VOM set to 50 VAC and correlate the readings with the legend on the side of the transformer. The transformer must also be correctly grounded, so check the ground potential as well, especially if there is a hum bar rolling up or down the TV screen.
HARNESS PROBLEMS Other harness problems include blowing fuses and malfunctioning controls. The repeating blown-fuse problem can sometimes be quite exasperating to solve, for short circuits have the tendency to occurin areas almost impossible to find. First, try inserting a new fuse, as old fuses age and blow without cause. If the new one also blows, you definitely have a short. The best way to approach this problem is by turning the power off and disconnecting devices that may be causing the problem, such as the TV, transformer, and PCB. Disconnect the devices by pulling off their connectors, but do not allow them to touch. If necessary, insulate them with small pieces of electrical tape. Then, connect your VOM across the terminals of the fuse block (all electrical power shut off), and set it to one of the resistance scales. This will save blowing a fuse each time you want to check the circuit. If the VOM reveals that disconnecting the devices removed the short, reconnect the devices one by one until the short returns. The last device connected is the one that is at fault. If the VOM readsa short even after the devices are disconnected, the fault must lie in the harness itself, and only patient exploration will reveal its location. First, carefully examine all the wiring, looking for terminals that may be touching, metal objects such as coins shorting connections or burned insulation. If necessary, use the VOM to check each suspected wire. MALFUNCTIONING CONTROLS One of the most common problems here is a bad potentiometer. Typically, a bad pot will cause the image to jump as it reaches a certain point. The only cure for this one is to install a new pot. If a feature that is operated by a switch (forexample, joysticks, foot pedals, control pane! buttons) does not operate at ail, check the switch with a VOM or continuity tester to verify its operation. If the switch does not check out, replace it. If the switch is OK, you should suspect the input to the switch from the PCB. In this case, get out the harness and logic schematics and check to see what kind of input itis. In many cases, the inputwill be +5 VDC. If so, use the VOM to check its presence. Normaily, the switch is used to pull a +5 VDC line LOW to GND or to pulla LOW line HIGH. If the PCB output is missing, check the wire length from the PCB. If you find the signal at ihe PCB trace, the wire length or connection is at fault. If not, begin exploring the PCB using the logic schematics.
A Glossary of Microprocessor Terms
MICROPROCESSOR — one or several microcircuits that perform the function of a computer's CPU. Sections of the circuit have arithmetic and comparative functions that perform computations and executive instructions.
CPU — central-processing unit. A computing system’s “brain”, whose arithmetic, control and logic elements direct functions and perform computations. The microprocessor section of a microcomputer is on one chip or several chips.
PROM — programmable read-only memory. User permanently sets binary on-off bits in each cell by selectively fusing or not fusing electrical links. Nonerasable. Used for low-volume applications.
EPROM — erasable, programmable, read-only memory. Can be erased by ultraviolet light bath, then reprogrammed, Frequently used during design and development to get programs debugged, then replaced by ROM for mass production.
ROM — read-only memory. The program, or binary on-off bit pattern, is set into ROM during manufacture, usually as part of the last metal layer put onto the chip. Nonerasable. Typical ROM's contain up to 16,000 bits of data to serve as the microprocessor’s basic instructions. RAM — random-access memory. Stores binary bits as electrical charges in transistor memory cells. Can be read or modified through the CPU. Stores input instructions and results. Erased when power is turned off. LSI — large scale integration. Formation of hundreds or thousands of so-called gate circuits on semiconductor chips. Very large scale integration (VLS) involves microcircuits with the greatest component density. MOS — metal-oxide semiconductor. A layered construction technique for integrated circuits that achieves high component densities. Variations in MOS chip structures create circuits with speed and low-power requirements, or other advantages (static will damage a MOS chip).
Introduction to the
Z-80 CPU
The term “microcomputer” has been used to describe virtually every type of small computing device designed within the last few years. This term has been applied to everything from simple “microprogrammed” controllers constructed out of TTL MSI up to low end minicomputers with a portion of the CPU constructed out of TTL LS! “bit slices.” However, the major impact of the LSI technology within the last few years has been with MOS LS}. With this technology, it is possible to fabricate complete and very powerful computer systems with only a few MOS LSI components. The Zilog Z-80 family of components can be configured with any type of standard semiconductor memory to generate computer systems with an extremely wide range of capabilities. For example, as few as two LSI circuits and three standard TTL MSI packages can be combined to form a simple controller. With additional memory and I/O devices a computer can be constructed with capabilities that only a minicomputer could previously deliver. New products using the MOS LS! microcomputer are being developed at an extraordinary rate. The Zilog Z-80 component set has been designed to fit into this market through the following factors:
- The Z-80 is fully software compatible with the popular 8080A CPU. . Existing designs can be easily converted to include the Z-80. . The Z-80 component set is at present superior in both software and hardware capabilities to any other microcomputer system on the market today. . For increased throughput the Z80A operating ata 4 MHZ clock rate offers the user significantspeed advantages. Microcomputer systems are extremely simple to construct using 2-80 components. Any such system consists of three parts:
- CPU (Central Processing Unit)
- Memory
- Interface Circuits to peripheral devices The CPU is the heart of the system. Its function is to obtain instructions from the memory and perform the desired operations. The memory is used to contain instructions and in most cases data that is to be processed. For example, a typical instruction sequence may be to read data from a specific peripheral device, store it in a location in memory, check the parity and write it out to another peripheral device. Note that the Zilog component set includes the CPU and various general purpose I/O device controliers, while a wide range of memory devices may be used from any source. Thus, all required components can be connected together in a very simple manner with virtually no other external logic.
General Purpose Registers There are two matched sets of general purpose registers, each set containing six 8-bit registers that may be used individually as 8-bit registers or as 16bit register pairs by the programmer. One set is called BC, DE and HL while the complementary set is called BC’, DE’ and HL’. At any one time the programmer can select either set of registers to work with through a single exchange command for the entire set. In systems where fast interrupt response is required, one set of general purpose registers and an accumulator/flag register may be reserved for handling this very fast routine. Only a simple exchange command need be executed to go between the routines. This greatly reduces interrupt service time by eliminating the requirement for saving and retrieving register contents in the external stack during interrupt or subroutine processing. These general purpose registers are used for a wide range of applications by the programmer. They also simplify programming, especially in ROM based systems where little external read/write memory is available. Arithmetic & Logic Unit (ALU) The 8-bit arithmetic and logical instructions of the CPU are executed in the ALU. Internally the ALU communicates with the registers and the external data bus on the internal data bus. The type of functions performed by the ALU include: Add Left or right shifts or rotates (arithmetic and logical)
Subtract Increment
Logical AND Decrement Logical OR Set bit Logical Exlusive OR Reset bit Compare Test bit Instruction Register and CPU Control As each instruction is fetched from memory, it is placed in the instruction register and decoded. The control sections performs this function and then generates and supplies all of the control signals necessary to read or write data from or to the registers, control the ALU and provide all required external control signals.
Z-80 CPU Pin Description The Z-80 CPU is packaged in an industry standard 40 pin Dual In-Line Package. The I/O pins are shown in the below figure and the function of each is described.
| yw | «74 | 2 a, |
/}—— a, waco =] a
| SYSTEM | ona | J | | 3» a, |
| CONTROL ™ 55 | at | 34 |
oo [> A
| 7 | 22 | 35 |
- [—— As
- Ay ASH 22] a Bg, ADDRESS
| — | 18 | 30 | BUS |
HALT + <——_ Z-80 CPU As 40 Aw
| —_ | 24 | 1 |
—*4 | Ay
| cpu | WAIT | 2 |
CONTROL Aa
| _ | 16 | Se | Ay |
| mm | | | 4 |
p>» A, ns Peo, RESET ————* CPU BUSRQ nl BUS BUSAK <#——+ CONTROL
jv. ete o,
| 6 | 12 | ‘ |
| 0) | __——»| | + Dd, |
1 8
| ow | rt | DATA | |
| GND | ——» | a D, | BUS |
jae v, 10 De 13, Z-80 PIN CONFIGURATION - Ls
4-4
Ao-Ais (Address Bus) Tri-state output, active high. Aj-Ais constitute a 16bit address bus. The address bus provides the address for memory (up to 64K bytes) data exchanges and for I/O device data exchanges. I/O addressing uses the 8 lower address bits to allow the user to directly select up to 256 input or 256 output ports. Ap is the least significant address bit. During’ refresh time, the lower 7 bits contain a valid refresh address.
D,-D, (Data Bus) Tri-state input/output, active high. D)-D, constitute an 8-bit bidirectional data bus. The data bus is used for data exchanges with memory and I/O devices.
M, (Machine Cycle one) __ Output, active low. M, indicates that the current machine cycle is the OP code fetch cycle of an instruction execution. Note that during execution of 2-byte op-codes, M1 is generated as each op code byte is fetched. These two byte op-codes always begin with CBH, DDH, EDH or FDH. M1 also occurs with IORQ to indicate an interrupt acknowledge cycle.
MREQ (Memory Request) Tri-state output, active low. The memory request signal indicates that the address bus holds a valid address for a memory read or memory write operation. 1oORQ (Input/Output Request) Tri-state output, active low. The ioRQ signal indicates that the lower half of the address bus holds a valid I/O address for a I/O read or write operation. An IORQ signal is also generated with an M1 signal when an interrupt is being acknowledged to indicate that an interrupt response vector can be placed on the data bus. Interrupt Acknowledge operations occur during M, time while I/O operations never occur during M, time. RD (Memory Read) Tri-state output, active low. RD indicates that the CPU wants to read data from memory or an I/O device. The addressed 1/O device or memory should use this signal to gate data onto the CPU data bus. WR (Memory Write) _ Tri-state output, active low. WR indicates that the CPU data bus holds valid data to be stored in the addressed memory or I/O device.
4-5 RFSH (Refresh)
Output, active low. RFSH indicates that the lower 7
bits of the address bus contain a refresh address for dynamic memories and the current MREQ signal should be used to do a refresh read to all dynamic memories.
HALT (Halt state)
Output, active low. HALT indicates that the CPU has
executed a HALT software instruction and is awaiting either a non maskable or a maskable interrupt (with the mask enabled) before operation can resume. While halted, the CPU executes NOP’s to maintain memory refresh activity. WAIT (Wait) Input, active low. WAIT indicates to the Z-80 CPU that the addressed memory or I/O devices are not ready for a data transfer. The CPU continues to enter wait states for as long as this signal is active. This signal allows memory or I/O devices of any speed to be synchronized to the CPU.
INT (Interrupt Request) Input, active low. The Interrupt Request signal is generated by I/O devices. A request will be honored at the end of the current instruction if the internal software controlled interrupt enable flip-flop (IFF) is enabled and if the BUSRQ signal is not active. Wnen the CPU_accepts the interrupt, an acknowledge signal (IORQ during M, time) is sent out at the beginning of the next instruction cycle. The CPU can respond to an interrupt in three different modes that are described in detail in section 5.4 (CPU Control Instructions).
NMI (Non-Maskable Interrupt) Input, negative edge triggered. The non maskable interrupt request line has a higher priority than INT and is always recognized at the end of the current instruction, independent of the status of the interrupt enable flip-flop. NMI automatically forces the Z-80 CPU to restart to location 0066H. The program counter is automatically saved in the external stack so that the user can return to the program that was interrupted. Note that continuous WAIT cycles can prevent_the current instruction from ending, and that a BUSRQ will override a NMI.
RESET Input, active low. RESET forces the program counter to zero and initializes the CPU. The CPU initialization includes:
- Disable the interrupt enable flip-flop
- Set Register |= 00H
- Set Register R =00#
- Set Interrupt Mode 0 During reset time, the address bus and databus go to a high impedance state and all contro! ouput signals go to the inactive state.
BUSRQ (Bus Request) Input, active low. The bus request signal is used to request the CPU address bus, data bus and tri-state output control signals to go to a high impedance state so that other devices can control these buses. When BUSRQ@ is activated, the CPU will set these buses to a high impedance state as soon as the current CPU machine cycle is terminated. BUSAK (Bus Acknowledge) Output, active low. Bus acknowledge is used to indicate to the requesting device that the CPU address bus, data bus and tri-state control bus signals have been set to their high impedance state and the external device can now control these signals.
CLK (Clock) Single phase TTL level clock which requires only a 330 ohm pull-up resistor to +5 volts to meet all clock requirements.
MCR II SYSTEM P.C. BOARD JUMPER OPTIONS
VIDEO GENERATOR P.C. BOARD
MANUFACTURER | EPROM NO.j| JW#1 JW#2 JW#3 JW#4 JWHS JWHE JWH7 JW#8
MOTOROLA
JUMPER OP- NUMEROUS MFR'S TION FOR PROGRAM NUMEROUS MFR'S ROMs ONLY.
# = LEAVE JUMPER WIRES WHERE THIS SYMBOL “#” APPEARS
% = CUT JUMPER WIRES WHERE THIS SYMBOL “*” APPEARS.
The above table illustrates the fact that the Video Generator P.C. Board used in the MCR II System has 8 jumper wires, the C.P.U. P.C. Board used in the MCR II System has 6 jumper wires, and the Sound I/O P.C. Board used in the MCR !! System has 2 jumper wires. All of the above Boards can be used with a variety of different SETS of EPROM chips. However, these EPROMS are not all made by the same manufacturer and do have some internal differences. So, in order to make them function properly in their respective P.C. Boards, certain jumper wires on these Boards have to be cut.
The above table tells you which jumpers to cut (depending on which EPROM set you're going to use) by showing a “*” under that jumper wires number. If there is a “#" under a jumper wires number, THAT PARTICULAR JUMPER WIRE IS NOT TO BE CUT.
4-7
V. Coin Door Maintenance
SPECIAL NOTE: If you have any questions about the coin acceptors in your game(s), please feel free to contact their manufacturers. Each manufacturer's name is PROMINENTLY imprinted on every acceptor mechanism. Metal mechanisms only: COIN MECHANISMS, INC. 817 Industrial Drive Elmhurst, IL 60126 Phone (312) 279-9150
COIN DOOR MAINTENANCE
METAL COIN ACCEPTOR MECHANISMS Periodically, the metal coin acceptor mechanism(s) must be removed from the coin door and cleaned.
- Make sure the power to the game is off.
- Unlock and open the coin door.
TO REMOVE PUSH LATCHES DOWN
PLACE PEGS IN SLOTS TO REPLACE PULL MECHANISM OUT Metal and Plastic mechanisms: COINCO COIN ACCEPTORS, INC. 860 Eagle Drive Bensenville, IL 60106 Phone (312) 766-6781
- Remove the coin acceptor mechanism as shown in Figure 5-1. O Push down on the two spring loaded latches. O While holding the latches down, pull the top of the coin acceptor mechanism toward you. O Release the latches and lift out the coin acceptor mechanism.
PUSH MECHANISM IN
Figure 5-1 Removing and Replacing the Coin Acceptor
4, Clean the magnet of all foreign particles. See Figure 5-2. O This may be accomplished by swinging the gate open as shown in the above figure.
- Remove the cradles and undersize levers and clean the bushings. (A pipe cleaner makes a good bushing cleaner.) O Also clean the pivot pin.
- Whenever needed, the coin acceptor should be cleaned with hot water and cleanser in the following manner: Place the coin acceptor in boiling water for about ten minutes.
O Next, use a brush and kitchen cleaner to remove all remaining foreign matter from the unit. C Rinse the coin acceptor in clean boiling water. O Dry the coin acceptor thoroughly by using filtered compressed air to blow it dry.
GATE OPEN AS SHOWN CLEAN MAGNET BY DRAGGING A SCREWDRIVER BLADE ACROSS SURFACE
Figure 5-2 Cleaning the Metal Coin Acceptor
- To lubricate the coin acceptor: O Use ONLY powdered graphite and put it ONLY on the moving parts of the coin acceptor. These parts are called out in Figure 5-3. O Be extremely careful to keep the powdered graphite away from paths that are traveled by the coins.
- WARNING — DO NOT USE OIL TO LUBRICATE THE COIN ACCEPTOR.
- Check the coin chute for obstructions such as: Paper, gum, etc.
- Reinstall the coin acceptor to the coin door. See Figure 5-1. O Place the two pegs at the coin acceptor’s base into their retaining slots. 0 Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches.
- Close and lock the coin door.
APPLY POWDERED GRAPHITE HERE
CRADLE
Figure 5-3 Lubricating the Metal Coin Acceptor
5-2
SQUEEZE PINS TOGETHER TO UNLOCK
HOLDING BOTH GATES TOGETHER, PUSH UP AND PULL OUT
Figure 5-4 Opening the Plastic Coin Acceptor
PLASTIC COIN ACCEPTOR MECHANISMS
The plastic coin acceptor mechanism(s) must be removed periodically from the coin door and cleaned.
- Make sure the power to the game is off. 2, Unlock and open the coin door.
- Remove the coin acceptor mechanisms(s) as shown in Figure 5-1. C] Push down on the two spring loaded latches. O While holding the latches down, pull the top of the acceptor mechanism toward you. O Release the latches and lift out the mechanism.
- Squeeze the two pins indicated in Figure 5-4 together to open the mechanism and break it down into its three basic parts. O Clean the mechanism in hot soapy water. It never rusts. O Rinse the mechanism in clean hot water and allow it to dry. O Reassemble the mechanism (it never needs lubrication).
- Check the coin chute for obstructions such as: paper, gum, etc.
- Reinstall the coin acceptor to the coin door. See Figure 5-5. O Place the two pegs at the coin acceptor’s base into their retaining slots. O Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches.
- Close and lock the coin door.
ACCEPTOR CAN BE SET TO ACCEPT U.S. QUARTERS ONLY OR BOTH U.S. AND CANADIAN QUARTERS.
MAGNET
FS
SLIDE MAGNET TO EXTREME RIGHT (AS SHOWN) TO ACCEPT BOTH U.S. AND CANADIAN QUARTERS.
TO ACCEPT U.S, QUARTERS ONLY, SLIDE MAGNET TO EXTREME LEFT.
Figure 5-5 Changing the Plastic Coin Acceptor to Accept American or Canadian Quarters
PLEASE NOTE:
THE INFORMATION CONTAINED IN THIS SECTION 1S TOLD IN AN EASY TO UNDERSTAND MANNER AND IS INTENDED TO AID THOSE WITHOUT AN ELECTRONICS DEGREE IN TROUBLESHOOTING AND REPAIRING THEIR GAMES T.V. MONITOR.
IF YOU READ THROUGH THIS SECTION AND STILL HAVE QUESTIONS, PLEASE CONTACT YOUR DISTRIBUTOR OR MIDWAY MANUFACTURING COMPANY AT THE TOLL FREE NUMBER PROVIDED WITH YOUR GAMES PAPERS.
OUR STAFF AND OUR DISTRIBUTORS STAND READY TO HELP YOU!
THANK YOU
Introduction: (How to
use this section of your manual.)
This section has been designed to simply familiarize you with one of the more mystical components in your game — the T.V. monitor. If you are an electronics technician who is quite knowledgeable on the subject, you may decide to just go to the schematics and start troubleshooting the defective monitor. But if you are like most people, a monitor is a T.V. set, and that means a complex doo-dad that means big buck repairs. This isn’t necessarily so. This section of the manual will acquaint you with the monitor and could just help you repair it if you feel adventurous enough to give it a try. if you have any knowledge of electronics, especially the use of a voltmeter, the repairs you can make are astonishing. Just keep in mind that ELECTRICITY CAN BE VERY DANGEROUS, SO BE CAREFUL!!
If you want to understand how a monitor works, just read the “THEORY OF OPERATION” subsection. If you wish, you can follow along with the schematics. The information is presented in a very basic manner but 4 more complete treatment of the subject can be found in the technical sections of bookstores.
'f you want to attempt to repair your monitor, it would be a good idea to read this whole section beginning to end before starting. Pay attention to all warnings and take them seriously. The more equipment you have the better, but a low cost Volt-Ohm-Milliameter can often do the trick. Here are the steps to take:
- Find the symptom that matches the problems your monitor has in the “SYMPTOM — DIAG- NOSIS” subsection. The diagnosis tells the cir- Cuit or area the problem may be in and possibly even the actual component causing it. . Once you have the circuit that is causing the trouble, read the “TROUBLESHOOTING” subsection to learn the procedure for finding the bad part. Next, go to the schematic section and find the schematic that matches your monitor. It may be helpful to read the “DIFFERENCES BETWEEN MONITORS” subsection if you are unsure of which monitor you have. Use the schematic to see what parts are in the offending circuit.
That really is all there is to it. Just remember that there are some bizarre or rare symptoms not covered, or that a monitor may have two or more different problems that only a genius, the experienced, or an experienced genius can figure out. But be patient, follow safety precautions, and remember that there is also literature available from the monitor companies through your distributor or from Bally Midway Manufacturing Company on request. (There is a toll free number on the back side of the front cover of this manual.)
Symptom Diagnosis
- Insufficient width or heighth: A. Horizontal line (due to VERTICAL CIR- CUIT DEFECT). O Bad yoke. O Bad vertical output section. O Open fusible resistor in vertical section. O Bad height control. O Bad flyback. B. Vertical line (due to HORIZONTAL CIR- CUIT DEFECT). O Bad yoke. D Open width coil. O Open part in horizontal output section.
- Picture spread out too far or crushed in certain areas: A. Horizontal or vertical output transistor. B. Bad Component in output circuitry. C. Vertical linearity or damper control needs adjustment.
- Line too close with black spacing: A. Problem in vertical section causing poor linearity.
- Poor focus and convergence: A. Bad high voltage transformer (“flyback”) or control. B. Focus voltage wire not connected to neckboard terminal.
- Colors missing; check: Interface color transistors. Color output transistors. Cracked printed circuit board (neck Board). Color circuits. Video input jack. Defective picture tube.
- Picture not bright enough: A. Weak emission from picture tube.
- Silvery effect in white areas; check: A. Beam current transistors. B. Weak picture tube emission.
- Too much brightness with retrace lines; check: A. Beam limiter transistors. B. Brightness and/or color blanking control set too high.
- Increasing brightness causes an increase in size and poor focus. A. Weak high voltage rectifier or regulation (high voltage unit). B. Bad component in monitor's power supply. ™moom> 10.
11.
12.
13,
14,
15.
16.
17.
18.
19.
20. Small picture and/or poor focus: A. Low B+ voltage (power supply trouble).
Vertical rolling: A. Vertical oscillator in the IC, vertical sync. transistor, or circuit. B. No sync from logic board. C. Three pin sync. jack is loose or plugged in wrong. Horizontal line across center: A. Vertical output circuit is dead (see symptom No. 1. A.). B. Vertical oscillator is not putting out the right wave form. Picture bends: A. Horizontal sync needs adjusting. B. Magnetic or electromagnetic interference. Flashing picture, visable retrace lines: A. Broken neck board. B. Internal short circuit in the picture tube (arcing). Unsymmetrical picture or sides of picture: A. Defective yoke. No brightness, power supply operating — No high voltage for the picture tube; check: A. Horizontal oscillator. B. Horizontal amplifier and output. C. Flyback transformer (high voltage unit). No brightness, high voltage present; check: A. Heater voltage to the tube at the neck board. B. Screen-grid voltage for the tube. C. Focus voltage. D. Grid to cathode picture tube bias. No o nigh voltage; check: For AC input to the “flyback”. Horizontal deflection stages. Flyback transformer. Yoke. Power supply. moom>
No horizontal and vertical hold; check: A. Sync transistors and circuit. B. Wires and jack from logic board to the monitor. Wavey picture — (power supply defect); check: A. Transistors, diodes, electrolytic capacitors in the power supply.
. Moving bars in picture: A. Ground connector off between monitor and logic boards. B. Defect in the power supply (see wavy picture symptom).
Washed out picture (see picture not bright enough): A. Check video signal at the cathode pins with an oscilloscope. If there is about 80 volts’ peak to peak, the picture tube has weak emission.
. Monitor won't turn on: A. Problem in the power supply: Check fuse, transistors, open fusible resistor.
B. Shorted horizontal output transistor. C. Defective high voltage disabling circuit. D. Crack(s) somewhere on main chassis board.
- Can’t adjust purity or convergence:
A. Use a degausser to demagnetize the picture tube carefully following your degausser’s instructions. B. Picture tube defective. C. Nearby equipment is electromagnetically interferring. D. The poles of the earth are pulling off the purity — see “A” above. E. Poor focus or width of picture. F. Make sure you have the correct CRT number for that brand of monitor.
Guide To Schematic Symbols
THERMISTOR (POLARITY DOESN’T MATTER)
INDUCTOR, COIL, CHOKE (POLARITY DOESN'T MATTER)
(-) CATHODE
(+) ANODE
ZENER DIODE IRON CORE TRANSFORMER (SUCH AS A FLYBACK)
iC am FUSE (POLARITY DOESN’T MATTER)
CATHODE (-)
ANODE (+)
DIODE
COLLECTOR a COLLECTOR a
BASE ————~ BASE———— EMITTER et EMITTER “TT
NPN TRANSISTOR PNP TRANSISTOR
' WA
VARIABLE RESISTOR, POT, CONTROL RESISTOR (POLARITY DOESN'T MATTER) (POLARITY DOESN’T MATTER)
+
LINES ARE CONNECTED ELECTROLYTIC CAPACITOR
LINES ARE NOT CONNECTED CAPACITOR (POLARITY DOESN'T MATTER)
Hm = GROUND
Troubleshooting
Troubleshooting monitors requires experience, patience, and luck. The first step is to match the symptom the monitor displays to the diagnosis next to it in the “SYMPTOM-DIAGNOSIS" subsection. This will pinpoint the circuit the problem is probably in, and often the parts to check. Next, the circuit should be visually inspected to see if there are any parts broken, burned, or if something is there that shouldn't be, like a loose screw, etc. Some parts go bad before others and should be checked first. In fact, following is the general order in which parts usually go bad:
- Semiconductors (like transistors, diodes, and integrated circuits). Fusible resistors. Electrolytic capacitors. Resistors. Capacitors and coils. Always remember thata monitor can bite like a snake. Even when it is turned off, capacitors hold voltage and will discharge it to you should you be touching chassis ground. The picture tube or CRT, itself, is a giant capacitor, so avoid the flyback anode plug hole. With the monitor on, the power supply circuit and/or the flyback, which puts out at least 23,000 volts, CAN BE KILLERS! Avoid handling power transistors (usually output transistors) or ICs, yoke terminals, and other high power components when the monitor is on.
6-5 Be prepared for a fairly loud pop and a flash. The longer the monitor has been turned off, the smaller the pop and dimmer the flash. But BE CARE- FUL, picture tubes will hold a very healthy charge for at least a week if not longer. Even after you've discharged it once, it may still carry a residual charge. It’s better to be too careful than dead, which is why electronic equipment always carries stickers referring servicing to qualified personnel. Handle the side with the viewing screen against your chest when changing it. ALWAYS wear safety goggles when handling the picture tube. To maintain the safety and performance of the monitor, always use exact replacement parts. For instance, the wrong components in the power supply can cause a fire, or the wrong color transistor may give a funny color to the picture. Service your monitor on a nonconductive firm table like wood, NOT METAL, and take off all of your jewelry just in case, With all this in mind, you are ready to begin troubleshooting.
Observe the picture carefully. Try to vary the appropriate control that would most likely affect your particular symptom. For example, if there is poor brightness or no picture, try turning up the brightness or contrast control. If the controls have no effect at all, chances are there is trouble with the control itself, the circuit it controls, or a nearby circuit that may be upsetting voltages. Go to the list of symptoms and determine with the schematic where the bad circuit is.
Keep in mind that capacitors hold a charge as can the picture tube (for at least a week and usually longer), and could shock you.
First, check for obvious visual defects such as broken or frayed wires, solder where it is not supposed to be, missing components, burned components, or cracked printed circuit boards. If everything looks good up to this point, make sure that diodes, electrolytic capacitors, and transistors have their leads connected in the right polarity as shown on the schematic and the circuit board. Turn on the power and measure the voltages at the leads of the active devices such as tubes, transistors, or integrated circuits. Any voltage that does not come within at least 10% to 15% of the voltage specified on the schematic indicates either a problem with that device or a component connected with it in the circuit. The next step is to use the ohmmeter to narrow down the field of possible offenders.
To test a transistor, one lead of the ohmmeter is placed on the base; and the other lead placed just on the emitter, then on the collector. A normai transistor will read either high resistance (infinite), or tittle resistance (400 to 900 ohms), depending on the polarity of this type transistor. Then the leads should be switched, one remaining on the base, and the other switched from the emitter to the collector. Now the opposite condition should result: the resistance should be infinite if it was lower when the other lead was on the base. Consistantly infinite readings indicate an open, anda short is demonstrated by 0-30 ohms on most of these test readings. Finaily, place one lead on the collector, then the other on the emitter. No matter which lead is used, there should be infinite resistance, Any lower reading, such as 50 ohms (which is typical on a bad transistor), indicates a short. This all sounds pretty confusing, but a little experience on a good transistor will make you an expert in no time. Usually, the lowest ohmmeter setting is used for testing transistors. Once in a great while a transistor may check out good on this test, but may actually be “leaky” or break down only on higher voltages. If in doubt, changeit. Itis also wise to check the transistor out of the circuit just in case some component in the circuit is affecting the ohmmeter reading. A diode is tested like a transistor except it only has two leads. Again, there should be high resistance one way and little resistance the other. If it tests bad, take one lead out of the circuit in case somecomponentis messing up the ohmmeter reading.
Without special equipment, integrated circuits are checked by verifying the proper DC voltage on the pins and the correct AC wave form using an oscilliscope. BE CAREFUL: Shorting their pins can easily destroy them. Resistors are checked with an ohmeter and should usually be within ten percent of the value stated on them and on the schematic. You may have to desolder one lead from the printed circuit board. If you wreck the foil on the board, carefully solder a small wire over the break to reconnect the conductive foil. Capacitors are tricky. Their resistance goes up when checked with an ohmmeter which shows a charging action. As they suck up current from the meter, the voltage goes up and so does the resistance. If you are sure a particular circuit is giving you a problem and everything else checks out O.K., Electrolytic capacitors are prime suspects. Substitute a new one and keep your fingers crossed.
Theory of Operation
To understand what goes on inside the monitor, large general groups of circuits will be examined instead of laboriously analyzing the branches and small circuits that make up these groups. This will help avoid confusion and aid in a basic, concrete, knowledge of what makes up a monitor.
THE POWER SUPPLY — The AC going to the monitor from the game transformer is just like the voltage and current from your wall outlet. It jumps up and down going positive and negative sixty times a second. But a monitor needs nice, smooth DC; direct current, not alternating. So diodes chop up the AC and a big electrolytic capacitor filters it out to make it even smoother. Since the monitor is a big piece of electronic equipment, with many circuits demanding a lot of power from the power supply, there are also zener diodes and transistors to help maintain a nice, constant, smooth voitage so that the monitor circuits don’t jump around. And this is what happens when you see a wavy picture. There is AC creeping through the power supply, so it must be malfunctioning. If the voltage from the power supply is too iow, the other circuits will be starved for power and you may see a small, wavy picture, or noneatall. Some circuits receive voltages that are higher than what the power supply should put out. But they come from the flyback transformer which will be discussed later. THE INTERFACE SECTION OF THE CHASSIS — The interface section of the chassis is fairly easy to identify. It is right by the place where the video jack(s) from the logic board(s) plug into. There are sets of transistors that receive the separate red, green, blue, and sync information from the cables that come from the logic boards. The circuits jack up the voltage and match impedances, or in other words, prepare the logic board outputs for the Circuits that will really amplify them for the output devices such as the yoke in the case of the sync, or the picture tube that shows the colors.
An interesting aside is that our sync is composite negative sync. That means two things:
- The sync is a negative going wave form.
- There are two pulses going at different speeds over the same wire: a. Vertical wave forms at 60 times per second (or Hertz) and b. Horizontal wave forms at about 15,750 times per second (Hz). The sync is amplified by a sync amplifier transistor and sent on its way to the oscillators. The sync or timing information will be explained along with the oscillator shortly. The color information is sent via wires to the neck board where the main amplification occurs. This will also be discussed later.
VERTICAL AND HORIZONTAL DEFLECTION— After the sync signal is amplified by the sync amp, it goes to two different sections, the vertical and horizontal circuits. Basically, the sync signals are for timing so the picture doesn’t mess up since it is assembled like an orderly jigsaw puzzle, but so fast that you can't see the electron beams for each color painting the picture on the screen. This will all become clear soon. For now, we will follow the 60 cycle component of the sync as it goes on its journey to the deflection yoke. The 60 cycle pulse goes to the vertical oscillator to make sure this circuit goes back and forth (or oscillates) at 60 times a second. Without this pulse keeping the circuit at the correct speed, it may get lazy and oscillate at 58 cycles or lower, or get ambitious and oscillate at 62 cycles or higher. At the wrong speed, the picture will start to roll up or down. A Wells Gardner 13” (K4806) or 19” (K4906, K4956) color monitor uses an integrated circuit for its sync section. An Electrohome 13” or 19" color monitor uses an integrated circuit !C501 for its sync section. The Zenith monitor (CD19MXRFO6) also uses an IC for the sync processing. Wells Gardner uses HA11423, Electrohome uses HA11244, and Zenith uses 221-175 (their part number). These ARE NOT interchangeable! The idea is all the same. The output to the vertical amplifying transistors for all monitors must form a sawtooth wave form, sort of like a bunch of pyramids, racing through the yoke's vertical coils at 60 times a second.
Along the way to the output transistors, the 60 cycle pulse is shaped and amplified to do the job: the yoke magnetically pushes the electron beam to fill the screen out sideways looking at the screen with the greatest length going up and down. Or viewing the screen sitting like a home television set, the amplified vertical output fills the screen up and down. Watching a monitor like this, seeing only a horizontal line means a problem with the vertical coils of the yoke or
6-7 anything from the vertical output section on back to the oscillator. The horizontal section is very similar with a few exceptions. The horizontal wave shape is more like a square and has a frequency of 15,750 cycles a second. Both Wells Gardner and Electrohome use the other side of their respective integrated circuits for the horizontal circuitry. If the oscillator isn’t going at the correct speed, the picture may move sideways, start to slant, or tear up with slanted thin figures. With both the vertical and horizontal of all monitors, there are variable resistors that change the speed of the oscillators up and down. This way you have controls that can make the correct frequencies to keep the electronic jigsaw puzzle nicely locked in place. If you're driving in acar and next to you someone else is driving their car at exactly the same speed, it will appear that they are not moving. And this is why the sync frequency and the oscillator’s frequency must match, so the picture doesn’t appear to move. The correct wave form is shaped and amplified in the circuitry just like in the vertical section. But the horizontal output transistor is a large power transistor and not only serves to give current to the horizontal yoke windings, it also feeds the flyback transformer.
THE FLYBACK TRANSFORMER (OR HIGH VOLTAGE UNIT) — The picture tube needs high voltage to light up, and the power supply can't meet this demand. The flyback transformer receives current alternating at about 15,750 times per second from the horizontal output transistor. The “flyback” jacks up its input voltage and puts out a higher voltage alternating at the same speed. But, in your “flyback” there are diodes that chop up the alternating voitage to make it asmooth DC output just like in the power supply. This is what goes through that thick red wire to your picture tube. THIS AREA HAS ABOUT 24,000 VOLTS. ON IT AND IT CAN KILL YOU! The “flyback” may be dangerous, but it is also generous. It has extra output windings which give voltage to the heater pins of the picture tube, voltage for the vertical deflection circuits, and picture tube screen-grid voltage. So in a way, the high voltage “flyback” is like a second power supply. COLOR CIRCUITS — The color circuits are pretty straight forward. The signals go into the interface section where some amplification and impedance matching occurs. These circuits are pretty sparse and simple. Each color just has two transistors and a diode with some resistors and capacitors. From here, the AC color signal is sent by wires to the neck board. The color output circuits are on the neck board. The color signals going to the transistors are controlled by two variable resistors called drive controls. There are only two, one for the red and one for the green on
Wells Gardner and Electrohome monitors. Zenith monitors have all three: red, blue and green. The Wells Gardner and Electrohome monitor have another variable resistor in their emitter part of their color output transistors. These “cutoff controls” vary the amount of A.C. signal that the transistor amplifies and sends to the cathodes of the picture tube. The Zenith monitor has its cutoff controls in the interface section to vary the amount of signa! going to the output transistors. The more signal, the more color. If you think this is confusing, here is another little hitch. The Electrohome and Zenith monitors both have the actual A.C. picture information signal going through the emitters of the color output transistors. The Wells Gardner has the A.C. signal going to the base of the transistors. The blanking and beam limiting signals which come from the blanking and beam limiting transistors in the interface section go into the color output transistor base in the Electrohome and Zenith monitors, but enters into the emitter of the Wells Gardner monitor's color output transistor. Should you feel adventurous enough to look at this signal on an oscilloscope, it should look like a square. The beam limiter helps control the brightness level, and the blanking transistor rapidly turns the picture tube on and off so that retrace lines don’t show up on the screen. By turning up the brightness on a good monitor, these four to six retrace lines can be seen slanting diagonally across the picture. PROTECTION CIRCUIT — To protect the high voltage section against voitages that are too high coming from the power supply which could cause X-rays to be emitted from the “flyback”, a Circuit senses the higher power supply voltage and turns off the horizontal oscillator. Since the horizontal oscillator doesn’t work, the horizontal output transistor has nothing to feed the “flyback” which in turn has nothing to feed the picture tube. The monitor will be silent, have no picture, and will appear to be off. But don’t be fooled. There is stili that excessive amount of voltage coming from the power supply. To find out, check at pin two of Wells Gardner's 1C501 and emitter of X04 for the Electrohome monitor. Check the 95 volt test point (located near the “flyback”) for the Zenith monitor. The Wells Gardner monitor doesn’t use this circuit, but an open in the horizontal section could cause the monitor to appear off, yet still have power supply voltage flying around. Here are the voltages you should receive: Wells Gardner = 130VDC Electrohome 120VDC Zenith = 95VDC The best place to measure this voltage on an Electrohome monitor is at a pin marked B1 on the chassis. This is because a 13 inch color Electrohome monitor, The GO7-FBO or GO7-902, has an integrated circuit and very little else in the power supply. Still, there should be 120VDC at B1. THE PICTURE TUBE (OR CRT) —
ATTENTION! For information on picture tube replacement types, go to the last section, “PICTURE TUBE INTERCHANGEABILITY”.
The picture tube or CRT is an output device. In other words, the end result of the circuit's work is displayed by this part. Actually, the output of other circuits is in the neck of the picture tube. First, there is the heater. The heater boils off electrons from the cathodes so that they (the electrons) shoot up to the screen to excite the phosphors so that the three phosphors emit three colors of light. The cathodes are next, and again they emit electrons to turn on the tube phosphors, making it glow. A defective cathode may cause the particular color it handles to be missing. Next come the grids. The first grid is grounded. The following grid is the screen grid which receives about 300VDC depending on the brightness setting. The next grid closest to the picture tube screen is the focus grid which gets about one fifth the amount of voltage that is applied to the picture tube anode. After jetting from the cathode through all these grids, the electrons speed through a mask, a sheet of material with tiny holes, and then excite the tiny dots of phosphor in the inside surface of the picture tube screen. The green electron gun (or cathode and circuitry) spits out electrons which head for the green phosphors only. The same goes for the red and blue guns. The way the phosphor light blends determines the color seen. Should these electron beams become too intense, they may burn the phosphor. With the monitor off, this can be seen as a dark permanent image of the video information on the tube screen.
Differences Between Monitors
The easiest way to identify the brand of monitor you are working with is to find the manufacturer's name or model number printed on the chassis or chassis base. But what if the monitor was in a Texas dust storm or buried in volcanic ash and this information is no longer there? Fear not! Each monitor has its own peculiarities and the following should help to identify them: The ELECTROHOME G07-904 (19”) and G07-902 (13") have their horizontal and vertical processing IC hidden under a silver can. A shiny metal top behind the “VERTICAL HEIGHT” and “HORIZONTAL FRE- QUENCY” contro! prove this is an Electrohome monitor.
The WELLS GARDNER K4906 (19") and K4806 (13”) have their horizontal and vertical processing IC out in the open directly behind the “VERTICAL HOLD” control. The ZENITH CO19MXRFO6 (19") monitor has its horizontal and vertical processing IC way in back by the picture tube. The monitor also has large white cables going from the main board to the neck board. K4906 (1st TYPE) — This monitor's identifying tags have BLACK ink printed on a white background. There is NO Vertical Damping Control. (This Control would be next to the Vertical Hold Control but this area is jumpered with a small wire instead. K4906 (2nd TYPE) — This monitor's identifying tags have RED ink printed on a white background. There IS a Vertical Damping Control next to the Vertical Hold Control. The Damping Control provides a few more lines on the top of the monitor screen (monitor viewed as a normal T.V. would be) for any video game that may need these lines to fit the picture on the screen. Moving the Control may distort the top part of your picture (or the side, depending on the game and how the monitor is mounted) so go ahead and move it if you are having this type of problem. To accommodate this new feature, there are a few circuit changes. ONE MAJOR DIFFERENCE BETWEEN THESE TWO VERSIONS OF THE K4906 IS THE YOKE. They look the same but notice the part numbers: K4906 WITHOUT the Damper Control: 2021111201 K4906 WITH the Damper Control: 2021111258 Since the companies like to change part numbers at the drop of a hat, the best thing to do is to request whatever part number is written on your yoke. If you should get the wrong yoke, the results will be: Picture distortion. Excessive brightness. Too much or too little vertical picture size.
CONTROLS YOU MAY NOT TOUCH Basically, on the Electrohome monitor, you can move any control you want EXCEPT for the B1 control. This sets the power supply voltage (ideally at 120 VDC) and is located right behind VERTICAL HOLD. The 13” Electrohome DOES NOT have this control. It may also be wise not to move the VERTICAL LIN- EARITY since this distorts the picture and is hard to reset perfectly. If you do move it, turn on the Cross Hatch Test Pattern of your game and try to get the squares to the point where they are equal in size by readjusting this Linearity Control. On the Wells Gardner monitor, brightness is adjusted by the “BLACK LEVEL” Control which is right next to the Horizontal Frequency Control. Under the Focus Control is the “SCREEN” Control which youDO NOT touch. Yes, this control does adjust the brightness, but it is used to set the CRT bias and is adjusted at the factory. When Wells Gardner sets it, they mark the position with a black mark on the knob. If you move it, be sure to realign the mark and THEN set the BLACK LEVEL Control to the brightness you desire. So, other than the SCREEN control, you may adjust any of the controls. The Zenith monitor has a 95 volt adjustment control. It is green and located behind the jack labeled 3D3. To discourage you from moving it, Zenith has placed a little glue on top of this control.
Parts Interchangeability
Some parts can be interchanged on all of the monitors. Here are the rules:
- You CAN swap any resistor between monitors that has the same resistance, wattage rating, and tolerance.
- You CAN swap any capacitor between monitors that has the same capacitance and voltage rating.
- You CAN swap many of the parts between the 19" and the 13" versions of each manufacturer's monitor. BUT, be certain to compare the manufacturers’ part numbers to be positive the parts you want to interchange are identical. BE SURE you have read the section DIFFERENCES BE- TWEEN MONITORS which was covered earlier.
- You MAY BE ABLE to swap picture tubes between monitors. In the past you could swap any picture tube, but due to rampant engineering changes and new monitor models being introduced, you would need a computer to keep track of what could be swapped. For more information .on this subject, go to “PICTURE TUBE INTERCHANGEABILITY”.
- You CANNOT change any part that is a safety part, one that is shaded in gray on the schematic; it MUST be IDENTICAL to the original. To do otherwise IS DANGEROUS. For instance, the 13 inch Electrohome (G07-902) monitor “flyback” looks identical to the 19 inch Electrohome (G07- 904) monitor “flyback”. In fact, there is even a 19 inch Electrohome (GO07-905) monitor (which is an obsolete model) with a similar looking “flyback". NONE OF THESE ARE INTER- CHANGEABLE!!
- You CAN change any of the parts between the G07-904 and G07-907. They’re essentially the same monitor except that the G07-907 has a vertically mounted picture tube.
If there is any doubt about what parts can be swapped between each manufacturer's 19 inch and 13 inch models, compare the manufacturer's part number between each one. If they match up, they are the same part.
Picture Tube Interchangeability
13" MONITORS
There are currently two 13” monitors being used: the Wells Gardner K4806 and the Electrohome G07-902. The picture tubes used are NOT interchangeable. The pins on the neck of the CRT will not fit in the socket should you use the wrong CRT.
Here is a chart for all the 13” color monitors Bally Midway uses. ELECTROHOME — G07-902 — 370ESB22 WELLS GARDNER K4806 —370KSB22
19” MONITORS Here it gets a little tricky. All of the picture tubes will fit no matter which is used. But if you use the wrong one, you will have problems with purity and/or dynamic convergence. Purity trouble means that the color won't be true. If you turn up the color control for one color, instead of seeing that solid color it will show blotches or blobs of other colors on the screen.
Trouble with dynamic convergence means that there will be color fringing around solid lines at the edges of the screen.
The only way to ensure that you avoid these problems is to get the right picture tube or the right substitute.
Here is a list of the 19" monitors and the CORRECT CRT numbers.
ALL ELECTROHOME G07-904 — 19VMNP22 RCA 19VMJP22 RAULAND 510UJB22 HITACHI
WELLS GARDNER K4906 — 19VLTP22 RCA 19VMLP22 ZENITH 19VMKP22 PHILLIPS
ZENITH CD19MXRFO6 — 19VMLP22 ZENITH 19VLTP22 RCA 19VMKP22 PHILLIPS The factory recommended CRT type could change in the future for one reason or another, but the listed picture tubes will work. As a matter of fact, you can call another picture tube company to see if they have a replacement number to recommend...but caveat emptor — let the buyer beware.
. Monit |
Notes Schematics
19” COLOR MONITOR SCHEMATIC DIAGRAM MODELS 19K4901, 194906, 19K4951, 19K 4956 Power Supply Voltage and Symbols | symbo! | Voltage | Operating Cir OSCILLOSCOPE WAVEFORM PATTERN The waveforms shown are as observed on the wide band oscilloscope with the monitor turned to a reasonably strong signal and a normal picture. The voltages shown on each waveform are the approximate peak amplitudes.
| e 130V
(C) X-RAY RADIATION PRECAUTION:
THIS PRODUCT CONTAINS CRITICAL LECTRICAL AND MECHANICAL PARTS
| | Hore ee | | | | | ESSENTIAL FOR X-RAY RADIATION | LE DEGRE DE SECURITE DEL/APPAREIL | If the waveforms are observed on the oscilloscope with |
| | | | Hore. Output | PROTECTION | DONT LE ONCTIONNEMENT EST | a poor high frequency response, the corner of the | |
| | ver. Output | FOR REPLACEMENT PURPOSES, USE | CRITIQUE POUR LA SECURITE QUE PAR | pulses will tend fo be more raunded than. those shawn |
and the amplitude of any high frequency pulse will tend to be less. DES PIECES RECOMMANDEES PAR LE Y TYP IN THE ONLY TYPE PARTS SHOWN FABRICANT. PARTS LIST. 175V | Video Output
351 COLLECTOR 2401 REO OUT 28C208e. 8K 2: aScIi4Bve/cve 2SCIBISBVCLVC 2SCIBI4BVC/CVE Ra ge fe q tf S62) aro E we) F Gea =) | acre pars 2 Fawweva)]
27kcneiv2)
| AVIDIV 200uSEC/DIV. | 20V/DIV 10uSEC/DIV: | io | 10 |
; f ce 9209 SCI
DRIVE] (S.DRIVE] OOTOrF RcsTOr#) (G.CUTOFF:
~Tes01° 8 sync. amp = -
| O.5/DIV 20u SEC/DIV | jzscisisy70 | | =f | HOD) |
SCO45 2V/DIV 200MSECIDIV or woes Ho OnE so a8 “yi eseasionn +h case Bata 1.C, 301, PIN 3 LC. 301, PIN 15
1VIDIV 20u SECIDIV
TP.31, AC COUPLED
NC AMP vosc Hose °°" : s 302 ¥ ‘ Tz z de Ear 306 toes & i coun 7,88 00068 bag) aan eels Lert a of
cher 20V/DIV SMSECIDIV AVIDIV 200uSEC/DIV- | (Hor
| 16.901, PIN 19 | NEGATIVE SIDE OF C203 | F | f | e | | | ts | sana |
[oRsize}
Peo! (D]
1VDIV 200uSECIDIV 2VIDIV SMSECIDIV 1VDIV 2MSEC/DIV CEGAUSSING COIL
- K4901D, K4906D, K4951D 5833 6-12 K4956B
REPLACEMENT PARTS LIST This monitor ccntains circuits and components included specifically for safety purposes. For continued protection no changes should be made to the original design, and components shown in shaded areas of schematic, or A *& on parts list should be replaced with exact factory replacement parts. The use of substitute parts may create a shock, fire, radiation or other hazard. Service should be performed by qualified personnel only.
MAIN BOARD
| Raf. No. | Part No. | Description | Ref. No. | Part No. | Deseription |
RESISTORS RESISTORS (CONT.)
| R201 | 203X6500-645 | 1K Ohm, 5%, 1/4W Carbon | R369 | 203X5602-229 | 680K Ohm, 5%, 1/2W Comp, |
| F202 | 203X6E00-523 | 30 Ohm, 5%, 1!4W Carbon | R370 | 203X6501-002 | 33K Ohm, 5%, 1/4W Carbon |
| R203 | 203X6500-405 | 100 Ohm, 5%, 1/4W Carbon | R371 | 203x9014-584 | 1K Ohm, 5%, 1W Metal Oxide |
| R204 | 203X6700-327 | 100 Ohm, 5%, 1/2W Carbon | R372 | 203X9101-119 | 12K Ohm, 5%, 1W Metal Oxide |
| 205 | 203X6700-421 | 270 Ohm, §%, 1/2W Carbon | RO75 | 203X6700-763 | 6.8K Onm, 5%, 1/2W Carbon |
| R206 | 203X6500-540 | 390 Ohm, 5%, 1/4W Carbon | R376 | 203X9104-404 | 270 Ohm, 5%, 2W Metal Oxide |
| R207 | 340X2201-934 | 200 Ohin, 5%, 1/4W Carbon | R377 | 203X6500-447 | 150 Ohm, 5%, 1/4W Carbon |
| 208 | 203X6500-540 | 390 Ohm, 5%, 1/4W Carbon | R378 | 203X6500-886 | 40K Ohm, 5%, 1/4W Carbon |
| R209 | 340X2201-934 | 200 Ohm, 5%, 1/4W Carbon | R379 | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon |
| Rz10 | 203X6500-540 | 390 Ohm, 5%, 1/4W Carbon | R380 | 203X6500-865 | 8.2K Ohm, 5%, 1/4W Carbon |
| R211 | 340X2201.934 | 200 Ohm, 5%, 1/4W Carbon | Ret | 203X6500-724 | 2.2K Ohm, 5%, 1W Metal Oxide |
| R214 | 203X6500-645 | 1K Ohm, 5%, 1/4W Carbon | R383, | 203X9014-387 | 150 Ohm, 5%, 1W Metal Oxide |
| R215 | 203X6501-126 | 100K Ohm, 5%, 1/4W Carbon | R502 | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon |
| R216 | 203x6500-645 | 1K Ohm, 5%, 1/4W Carbon | R503 | 204x 1700-535 | 150 Ohm, 5%, 15W Metal Oxide |
| R27 | 203X6500-405 | 100 Ohm, 5%, 1/4W Carbon | R504 | 203X9014-267 | 47 Ohm, 5%, 1W Metal Oxide |
| R218 | 203X6500-645 | 1K Ohin, 5%, 1/4W Carbon | R505 | 203X6501-209 | 2.2K Ohm, 5%, 1/4W Carbon |
| R219 | 203X6501-126 | 400K Ohm, 5%, 1/4W Carbon | R506 | 203x9104-105, | 45 Ohm, 5%, 2W Metal Oxide |
| R220 | 203X6500-645 | 1K Ohm, 5%, 1/4W Carbon | R507 | 203X5602-185, | 330K Ohm, 5%, 1/2W Comp. |
| 221 | 203X6500-405 | 100 Ohm, 5%, 1/4W Carbon | ARGO! | 204X1625-058 | 3.3 Ohm, 5%, 10W WW |
| R222 | 203X@500-762 | 3.3 Ohm, 5%, 1/4W Carbon | R701 | 203X9105-141 | 2.2 Ohm, 5%. 2W Metal Oxide |
| R224 | 203X6500-169 | 40 Ohm, 5%, 1/4W Carbon | R702 | 203X6206-441 | 2.2 Ohm, 5%, 1/2W Carbon |
| R225 | 203X6500-169, | 10 Ohm, 5%, 1/4W Carbon | VR201 | 204X2070-072 | 2k Ohm-B Semi-Fixed |
| R226 | 203x6500-169 | 10 Ohm, 5%, 1/4W Carbon | VR301 | 204x2070-084 | |
| R227 | 203X6501.044 | 47K Ohm, 5%, 1/4W Carbon | R303 | 204X2070-055 | 500 Ohm-B Semi-Fixed |
| R228 | 203X6500-645 | 1K Ohm, 5%, 1i4W Carbon | R381 | 204x2070-072 | 2K Ohm-B Semi-Fixed |
| R229 | 203X6700-421 | 270 Ohm, 5%, 1/2W Carbon | VR352 | 204X2070-072 | 2k Ohm-B Semi-Fixed |
| R230 | 203X6500-863 | 8.2K Ohm, 5%, 1/2W Comp. | |||
| R231 | 203X6500-863 | 8.2K Ohm, 5%, 1/2W Comp. | |||
| R232 | 203X6500-863 | 8.2K Ohm, 5%, 1/2W Comp. | |||
| R233 | 203X6500-468 | 180 Ohm, 5%, 1/4W Carbon | |||
| R234 | 340X2820-934 | 82 Ohm, 5%, 1/4W Carbon | CAPACITORS | ||
| R235 | 340X2820-934 | 82 Ohm, 5%, 1/4W Carbon | 201 | 203X0014-088 | 1000 uF, 16V, Electrolytic |
| R236 | 340X2820.934 | 82 Ohm, 5%, 1/4W Carbon | 202 | 202X7200-064 | 330 pF, 500V, Ceramic |
| A301 | 203X6500-508 | 270 Ohm,5%, 14W Carbon | 6203 | 202X7200-043 | 220 pF, 500V, Ceramic |
| R302 | 203X6500-863 | 8.2K Ohm, 5%, 1/4W Carbon | C204 | 202X7200-043 | 220 pF, 500V’ Ceramic |
| R303 | 203X6500-863 | 8.2K Ohm, 5%, 1/4W Carbon | 205 | 203X0014.076 | 470 uF, 16V, Electrolytic |
| R304 | 203X6500-724 | 2.2K Ohm. 5%, 1/4W Carbon | C206 | 203X1810-149 | 0.1 uF, 125V Mylar |
| R306 | 203X6500-842 | 6.8K Ohm, 5%. 1/4W Carbon | C207 | 349X2232-109 | .022 uF, 100V Mylar |
| F308 | 203X6003-201 | 7.5K Ohm, 2%, 1/4W Carbon | C301 | 203X0014.065 | 330 uF, 50V Electrolytic |
| R307 | 203X6500-825 | 5.6K Ohm, 5%, 1/4W Carbon | 302 | 203X1600-563. | 0.033 uF, 50V Mylar |
| R309 | 203x6500-965, | 22K Ohm, 5%, 1/4W Carbon | 6303 | 203X0629-037 | 3.3 uF, 50V Electrolytic |
| R310 | 203X6500-988 | 39K Ohm, 5%, 1/4W Carbon | 6308 | 203X 1600-366 | 0.068 pF, SOV Mylar |
| R311 | 203X6500-762 | 3.3K Ohm, 5%, 1/4W Carbon | C308 | 203X0412-012 | 2.2 uF, 16V Tantal |
| R312 | 203x9014-741 | 4.7K Ohm, 5%, 1/4W Carbon | C307 | 203X 1600-634 | 0.033 UF, 50V Mylar |
| R313 | 204X1450-537 | 1K Ohm, 5%, 5W Carbon | C308 | 203X0025-174 | 3.3 uF, 50V Electrolytic |
| R314 | 203X6500-481 | 220 Ohm, 5%, 1/4W Carbon | 309 | 203X1207-100 | 0.068 UF, 100V PP |
| R15 | 203%6500-169 | 10 Ohm, 5%, 1/4W Carbon | C310 | 2030629-061 | 10 uF, 100¥ Electrolytic |
| R316 | 203X6500-762 | 3.3K Ohm, 5%, 1/4W Carbon | 311 | 203X0041-025 | 10 uF, 160V Electrolytic |
| R317 | 203X6700-107 | 12 Ohm, 5%, 1/2W Carbon | 312 | 202X7050-248 | 4000 pF, 500V Ceramic |
| R318 | 203X6500-540 | 390 Ohm, 5%, 1/4W Carbon | C313 | 203x0040.052 | 47 uF, 160V Electrolytic |
| F319 | 203X6500-645 | 1K Ohm, 5%, 1/4W Carbon | 314 | 203X 1201-265 | 0.033 uF, 200V PP |
| 320 | 203X8501-002 | 33K Ohm, 5%, 1/4W Carbon | 0315 | 203x0629-023, | 1 UF, 50V Electrolytic |
| R321 | 203X6501-224 | 270K Ohm, 5%, 1/2W Carbon | C351 | 203x0629-023 | 1 uF, 50V Electrolytic |
| R322 | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | C352 | 203X0619-045 | 47 uF, 25V Electrolytic |
| R351 | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | 6353 | 203X1190-015 | 0.0082 pF, 50V Mylar-PP |
| R382 | 203X6500-785 | 3.9K Ohm, 5%, 1/4W Carbon | C354 | 203X0619.045 | 47 uF, 25V Electrolytic |
| R353 | 203X6501.086 | 68K Ohm, 5%, 1!4W Carbon | C355 | 203x1600-366 | 0.0068 pF, 50V Mylar |
| R354 | 203X6500-762 | 3.3K Ohm, 5%, 1/4W Carbon | C356 | 202X7050-483 | 0.01 UF, 500V Ceramic |
| R355 | 203X9205-143 | 6.8K Ohm, 5%, 3W Metal Oxide | 6359 | 202X8065-606 | 100 pF,'500V Ceramic |
| R358 | 203X5601-878 | 56K Ohm, 5%, 1/2W Carbon | C360 | 202X7050-366 | 0.0033 pF, 500V Ceramic |
| F360 | 203X8500-561 | 470 Ohm, 5%, 1/4W Carbon | C361 | 202X7050-483 | 0.01 uF, 500Y Ceramic |
| R361 | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | 0362 | 202X7203-032 | 0.01 uF, 50V Ceramic |
| R362 | 203x9014-645 | 1.8K Ohm, 5%, 1W Metal Oxide | D*C363 | 203X1270311 | 8700 pF, 1.5 KV PP |
| RIES | 204X1527-751 | 3.9K Ohm, 5%, 7W Metal Oxide | WC365 | 203X1201-265, | 0.33 uF, 200V PP |
| R364 | 203X6500-246 | 22 Ohm, 5%, 1/4W Carbon | C366 | 203X0019-026 | 22 uF, 25V Electrolytic |
| R365 | 203X6501-002 | 33K Ohm, 5%, 1/4W Carbon | C367 | 202X8065-162 | 6 pF, 500V Ceramic |
| R367 | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | C368 | 202X7203-032 | 001 UF, 50V Geramic |
| R368 | 203X5602-185 | 330K Ohm, 5%, 1/2W Comp. | 372 | 203X 1207-125 | 0.1 uF. 100V PP |
MAIN BOARD (CONT.)
| Ref. No. | Part No. | Description | Ret. No. | Part No. | Description |
CAPACITORS (CONT.) SEMICONDUCTORS (CONT)
| 6380 | 202x7200-087 | 470 uF, 500V Ceramic | 208 | 200X3181523 | Transistor (NPN) 28C1815GR |
| C501 | 203X1810-149 | 0.1 uF, 125V Mylar | Q207 | 200X3181-523 | Transistor (NPN) 2SC1818GR |
| 4 cs02 | 202X7050-282 | 1500 pF, 500V Ceramic | 9208 | 200X3181-523 | Transistor (NPN) 2SC1815GR |
| 4503 | 202X7810-214 | 2200 pF, 125V Ceramic | 200 | 200X3181.523 | Transistor (NPN) 28C1851GR |
| C504 | 202X7810.214 | 2200 pF, 128V Ceramic | 210 | 200X3181-823 | Transistor (NPN) 28C1851GR |
| 505 | 203X0220.075 | 560 UF, 200V Electrolytic | 301 | 200X3181-523 | Transistor (NPN) 2SC1851GR |
| 6506 | 203X0040-034 | 22 uF, 160V Electrolytic | 302 | 200X3207-308 | Transistor (NPN) 2502073, 6GL2 |
| C507 | 203X0041.057 | 47 uF, 160V Electrolytic | Q303 | 200X3207-306 | Transistor (NPN) 28C2073.8GL2 |
| 701 | 203x0018.092 | 4000 UF, 25V Electrolytic | 35% | 200x3248:217 | Transistor (NPN) 2502482BK |
| 702 | 203X0634.061 | 10 uF, 100V Electrolytic | 0352 | 200X4589.802 | ‘Transistor (NPN) 2808988 |
| 703 | 202X7050-248 | 1000 pF, 500V Ceramic | an nt | 200X2300-033 | IC HA11423 |
| 1c501 | 200x2600-183 | Ic STR381 |
SEMICONDUCTORS
| 0203 | 201X2010-159 | Diode, 1$2076-27 | |||
| 0204 | 201X2010-159 | Diode, 1S2076-27 | TRANSFORMERS & COILS | ||
| D205 | 201X2010-159 | Diode, 1S2076-27 | L361 | 201X4710-134 | Coll, (RF Choke) |
| 0206 | 201X2010-159 | Diode, 18207627 | i352 | 201X5000-083 | Coll, Horiz. Size |
| 0207 | 201X2010-159 | Diode, 1$2076-27 | L701 | 811%0004-007 | Coil, Adg. |
| D208 | 201x2010-188 | Diode. 18207627 | 7351 | 202X 1300-080 | Transformer, Hor. Drive |
| 209 | 201X2010-159 | Diode. 1$2076-27 | Ax 1352 | 200X9720-301 | HV-Unit M-11 |
| 0301 | 201%2010-165 | Diode, 1SSB1 | |||
| 302 | 201X2010-159 | Diode, 182076-27 | MISCELLANEOUS | ||
| 0303 | 201X2010-159 | Diode, 1S2076-27 | AF501 | 204x7120-073 | Fuse, 4 Amp. 125V |
| 0304 | 2012120009 | Diode, RH-IV | v402 | 206X5008632 | Recep W Wire 3P-M-8G |
| D305 | 201X2120-009 | Diode, RH-V | P201 | 204X9600-466 | Plug, PWB 3P-J |
| 308 | 201X2010-159 | Diode, 1$2076-27 | P202 | 204x9601-477 | Plug, PWB 6P- |
| A501 | 201X3120-216 | Diode, RM-1AV | P4ot | 204x9600.298 | Plug, PWB 4P.B |
| A502 | 201X3120.216 | Diode, RM-1AV | P501 | 204x9600.249 | Plug, PWB 2P.8 |
| 4.0503 | 201X3120-216 | Diode, RM-1AV | P60t | 204x9600-304 | Plug, PWB 4P.C |
| AD5OS | 201X3120-216 | Diode, RM-1AV | TH501 | 201X0100-112 | Thermistor |
| D505 | 201X3120-216 | Diode. RM-1AV | |||
| D506 | 201X3120-216 | Diode, RM-1AV | |||
| 0701 | 201X2130-234 | Diode, RU-2V | FINAL ASSEMBLY PARTS | ||
| D702 | 201X2120.009 | Diode. RHV | A 88X0138-506 | 19VLTP22 Pix Tube | |
| 201 | 200X3181-523 | Transistor (NPN) 2SC1815GR | 205X9800-158 | Lateral/Purity Assembly | |
| 202 | 200X3181-523 | Transistor (NPN) 2SC1815GR | 4 | 202X1111-201 | Yoke Deflection |
| 203 | 200X4056.260 | Transistor (PNP) 2SAS62-Y-TM | 204X9301-255 | CRT Socket | |
| 204 | 200X4056-260 | Transistor (PNP) 25A562:-TM | 291X5004-262 | Automatic Degaussing Coit Unit | |
| 2205 | 200X4056-260 | Transistor (PNP) 2SA562-Y-TM |
NECK BOARD RESISTORS CAPACITORS
| R401 | 203X6000-729 | 220 Onm, 5% 1/4W Carbon | C401 | 202X7050-269 | 1200 pF, 500V Ceramic |
| R402 | 203X6500-540 | 390 Ohm, 5% 1/4W Carbon | c402 | 202X7050-248 | 1000 pF, 500V Ceramic |
| R403 | 203X8000-661 | 820 Ohm, 5% 1/4W Carbon | 403 | 202X7050-248 | 1000 pF, 500V Ceramic |
| R404 | 203X6000-729 | 220 Ohm, 5% 1/AW Garbon | cans | 202X7050-282 | 1500 pF, 1.5KV Ceramic |
| R405 | 203X6500-540 | 390 Ohm, 5% 1/4W Carbon | C405 | 202X7050-483 | 0.01 uF, '500V Ceramic |
| R406 | 203X6000-661 | 820 Ohm, 5% 1/4W Carbon | |||
| R407 | 203X6000-729 | 470 Ohm, 5% 1/4W Carbon | |||
| R408 | 203X6000-998 | 270 Onm, 5% 1/4W Carbon | SEMICONDUCTORS | ||
| R409 | 2036000861 | 820 Ohm, 5% 1/4W Carbon | 401 | 200X3208-800 | Transistor (NPN) 2SC2068LB |
| R410 | 203X9104-824 | 15K Ohm, 5% 2W M.0. Forming | 402 | 200X3206-800 | Transistor (NPN) 28C2068L8 |
| Ratt | 203X9104-824 | 15K Ohm, 5% 2W M.O. Forming | 0403 | 200X3206-800 | Transistor (NPN) 28C2068LB |
| Ra12 | 203X9104-824 | 15K Ohm, 5% 2W M.O. Forming | |||
| R413 | 203X6000-998 | 2.7K Ohm, 5% 12W Comp. | L | ||
| Raid | 203X6000-998 | 2.7K Ohm, 5% 1/2W Comp. | E | ||
| R415 | 203X6000.998 | 2.7K Onm, 5% 1/2W Comp. | a | 06x: Lines BL shan Wire | 4 |
| RA16 | 203X9105-154 | 2.2 Ohm, 5% 2W Metal Oxide | 206X5000:21 | ire 4P-E | |
| R419 | 203X6500-741 | 2.7K Ohm, 5% t/4W Carbon | Pade: | Snaoend:264 | Plug, PWB 3P-A |
| 7 | 84 | P403 | 204X9600-981 | Plug, Pin 1P-D | |
| R420 | 203X6500-741 | 2.7K Ohm, 5% 1/4W Carbon | a | ||
| BY | P701 | 204X9601.020 | Plug, PWB 4P-E | ||
| Ra2t | 203X6500-741 | 2.7K Ohm, 5% 1/4W Carbon | |||
| R401 | 204X2115-.014 | 500 Ohm, -B Semi-Fixed | |||
| R402 | 204X2115-014 | 500 Ohm, -B Semi | |||
| VR403 | 204X2115-006 | 5K Ohm, -B Semi | |||
| vR404 | 204x2115-006 | 5K Om. -B Semi-Fixed | |||
| R405 | 204X2115-008 | 5K Ohm, -B Semi-Fixed |
mame a ‘Auyy nts RED XIO1.KiC8 one KiOS VIDEO AMR, 28ca84C XlO8.X104 the XI06 VIOEO AMR, 28A673¢_
L Target ngs vere aurea, 28C261! oF Bate 9
so it See ey fo rei
i3e. x38 1800,x8c8 | Bt ne [PBC484C or aBci8Rs p08. x306 —\— ; eRe od ou O15, |
meas rivewame a}, X308 MUA MITER 254673 Pi [3508 sLAnKine WK Bcaoae entices
X 901 POWER DRIVE 25C2680 ne X 902 ERROR AMP 2SC1890 reas, —————— rs
Boaioea, asciase POWER REGULATOR ros,
aT dae Be $Rle ai
Schematic Notes Unless otherwise specified Resistance: (Q) (K*KQ, M--MQ), 1/4 (W) carbon resistor Capacitance: 1 or higher—> (pF), less than 1 (yF) working voltage > 50 (V) ceramic capacitor Inductance: (V H) Electrolytic Cap: Capacitance Value (y F)/working voltage (V), NP — non-polar (or bipolar) electrolytic cap. Refer to the parts list for additional component information. 1701 2c RAY PROTECTOR BIPBE cscaawy Hees om 2 indicates test point connection 2scaeil or ZSCz6108K 250869 or asian 250820 ACI2OV 6OH:/SOH2 210% oh indicates chassis ground unless otherwise specified Hz _ indicates cycles per second For safety purposes (and continuing reliability) a replace all components marked with safety syrnbo! with identical type.
00-4147-04 Parts identification on circuit boards: G07-CBO e.g. SU1126A (R107 = R1107) SU3030A (A113 = R3113)
6-14
CRT Socket P.C.B. Ass'y (SU-3032A) Parts List (Cont.) Main PCB Ass'y (SU-1133A) Parts List (Cani.)
| REPLACEMENT PARTS LIST—ELECTROHOME 19” MONITOR | Colls | Coils | ||||
| Symbol | Description | Part Number | Symbol | Description | Part Number | |
| an | L3101 | Peaking Coil | QQL043K-101 | L1602 | Linarity Coil | 39835 |
| Components identified by the A symbol in the PARTS LIST and on the Schematic have special characteristics | Semi- | 1503 | Width Coil | C30380-A | ||
| important to safety. | conductors | L1504 | Heater Choke | C30445-A | ||
| P | + | Symbol | Description | Part Number | Transformers | |
| DO NOT degrade the safety of the set through improper servicing. | X3101 | Si. Transistor | 28C1514VC | symbol | Description | Part Number |
| X9102 | Si. Transistor | 28C1514VC | 71501 | Hor. Drive Transf. A46022-BM | ||
| X3103 | Si. Transistor | 2SC1514VC | T1503 | Side Pin Transf. | C39050-A4 |
Abbreviations for Resistors and Capacitors Miscellaneous f
| Symbol | Description | Part Number | Som tors | |||||||||
| Resistor | Capacitor | A | ACRT Socket | A76068 | Symbol | Deseription | Part Number | |||||
| ‘ | : | . | 11501 | Ic | HA11244 | |||||||
| CR | : | Carbon Resistor _ | C Cap. | : | Ceramic Capacitor | Main PCB Ass'y (SU-1133A) Parts List | i ‘Or | Si. Transistor | 28C1685(R) | |||
| Comp. R | : | Composition Resistor | M Cap. | : | Mylar Capacitor | Resistors | X1102 | Si. Transistor | 2SA673(C) | |||
| OMR | : | Oxide Metal Film Resistor | E Cap. | : | Electrolytic Capacitor | Symbol | Description | Part Number | X1103 | Si. Transistor | 2801685(R) | |
| VR | : | Variable Resistor | BP E Cap. | : | Bi-Polar (or Non-Polar) | R1406 | v | R209 | Qvz3230-002 | mrioe | SI, Wensletor | = 28A673(C) |
| MFR | : | Metal Film Resistor | Electrolytic Capacitor | R1408 | Vv | R 2009 | QVvz3230-002 | x1108 | Si. Transistor =»: 280185519} | |||
| CMF R | ‘Coating Metal Film Resistor | © | MM Cap | : | Metalized Mylar Capacitor | R1410 | CMF R 68q1WJ | QRxo1e-6R8—X1106 | St Transeo | ee | ||
| : | i | : | ; | R1414 | OM | R 33Ka1WJ | QRGO19J-332 | x1301 | Si. Transistor = 28C1685(R} | |||
| UNF R | : | Nonflammable Resistor | PP Cap. | : | Polypropylene Capacitor | R145, | OM | R 27kKaIwW | ORGO19N-272 | x1302 | Si. Transistor | 28C1685(R) |
| FR | : | Fusible Resistor | MPP Cap. | : | Metalized PP Capacitor | R1421 | OM | R 12K22WJ | arGo26-1232 | X1303 | Si. Transistor | 28A673(C) |
| PS Cap. | : | Polystyrol Capacitor | R1422 | VR 10Ke | QVvz3230-014 | ate | Si. Transistor | =: 2S 1688(R) | ||||
| Tan. Cap. | : | Tantal Capacitor | AFR1401 | AF | RR 6822WK | QRHO24K-680M | te | st Tancigioe | osue | |||
| NOTE: When ordering replacement parts please specify the part number as shown in this list including part name, and | ARt608 | ACME 5 “a” | aera ogee | x1402 | Si. Transistor | 280478 | ||||||
| model number. Complete information will help expedite the order. | R1509 | OM | R 10K22WJ | QRGO26J-103Z | aol | = eta | psceees (K LM.) | |||||
| Use of substitute replacement parts which do not have the same safety characteristics as specified, may create shock, | Ha | on | . eoonen., ff | pacers | x1902 | Si. Transistor | 2SC1890A (E.F) | |||||
| fire or other hazards. For maximum reliability and performance, all parts should be replaced by those having identical | R1515 | CME R 8.201WJ | QRX010)-8R2 | pres | BS Bate | wae | ||||||
| specifications. | R1822 | CMF R 4.701WJ | QRX019J-4R7 | D1103 | Si. Diode | wosA | ||||||
| R1523 | OM | R 6822WJ | QRGO26J-680Z | D1301 | Si. Diode | 18Z473H | ||||||
| P | i | ; | ‘i | R1528 | OM | R 39021WJ | QRGO19J-391 | 1401 | Si. Diode | 18Z473H | ||
| SERVICE REPLACEMENT PARTS LIST | Purity Shield Ass’y. Parts List | R1534 | 2N | oR | ERZ-COBzKa71 | 1409 | Pener Diode | RDI0F(C) | ||||
| Symbol | Description | Part Number | Symbol —_ Description | Part Number | VR1501 | zN_R | ERZ-CO5ZK271 | D1503 | Si. Diode | HE-1 | ||
| Main PC.B. Assy | SU-1133A | Degaussing Coil | 21-1007-30 | AR1703 | ACMF R 390%W+1% | QRV122F-3002 | 1504 | Si. Diode | VOsE | |||
| CRT Socket PC.B. Assy | SU-3032A | D911, | AR1704 | ACMF R 7.68KQYW+1% | — QRV142F-7681 | D1505 | Zener Diode | RD11E(B) | ||||
| Purity Shield Assy | 07-220083-03 | D912 | Rectifier 1 Amp 600V (2) | 28-22-27 | AR1901 | APosistor | ATS414 | 01506 | Si. Diode | Wwoea | ||
| ; | , | Pin Terminal (2) | 34-708-01 | R1902 | UNF R 207WK | QRFO76K-2RO | D1507 | Si. Diode | 18881 | |||
| Outside of the P.C.B. Ass'y | Pin Terminal Housing | ped | R1903 | CMF R 4.703WJ | QRX039J-4R7 | D1508 | Si. Diode | 1SZ473H | ||||
| Symbol | Description | Part Number | Purity Shield (2 pcs.) | 35-3847-01 | R1904 | OM | R 10K22W J | QRGo26J-103z | AD1701 | AZener Diode | RD20EV2 | |
| Picture Tube 19" | 17-7198-03 | Purity Shield (2 pes.) | 35-3847-02 | R1905 | OM | R 18K21WJ | QRGO19J-183 | AD1901 | ASi. Diode | 181887A | ||
| A | ADeflection Yoke | A29779-D=21-141-01 | C911 | Capacitor 100nF 10% 400V | 48-171544-62 | 4Q1908 | ACMF R 472%W+1% | QRV122F-470z | AD1902 | ASi. Diode | 1S81887A | |
| PC Magnet | A75034-B=29-32-01 | R921 | Resistor, Wirewound 330, 4W | ——42-113301-03 | AR1909 | VR 2ka | QvPsaoB-023E © A4D1903 | ASi, Diode | 1818874 | |||
| A | Alyback Transf. | A29951-B | Fire Retardant Term. Strip 4Lug | 34-492-09 | R1910 | ACMF R 2.74KQX%W+1% | QRV142F-2741 | AD1904 | ASi. Diode | 181887A | ||
| a | Auva - | ; | ‘A46600-A | AFR1901 | AF — R 2200%WK | QRH124K-221M | AD1905 | AZener Diode | RD6.8EV3. | |||
| 5 | esistor 220.0,25W K | QRF258K-221 | , | - | i | |||||||
| oor | C Capacitor 180pR ACI.SKV | QCZ0101.008 | CRT Socket P.C.B. Ass'y (SU-3032A) Parts List | Capacitors | Miscellaneous | ; | ||||||
| x01 | Si. Transistor | 28870 | Resistors | Symbol | Description | Part Number | Symbol | Description | Fart Number | |||
| x02 | Si. Transistor | 2SC1106A | Symbol | Description | Part Number | 1301 | BPE Cap. 3.3uF 50V A | QENetHA-Gasz | AF 1901 | ase tee | latin ie | |
| sc | Screw #8-% | 31-610818-06 | R3105 | == VCR 200 | avz3234-022 | C1402 | Tan Cap. 2.2uF 16V K | QEES1CK.2258 | AF1902 | AUL Fuse 3A | QMF66U1-3ROS | |
| sc | Screw % x % Pix Tube Mtg. (4) | 31-601418-12 | R3106 | v | R 200 | QVZ3234-022 | C1407 | E | Cap. 4.7uF 6.3VA | QEWS1JA-475 | ||
| WA | Pyramidal Lock Washer (4) | 33-255-01 | R3113 | Vv | R 5K | QVZ3234-053 | C1411 | E | Cap. 100uF 160VA | QEWS2CA-107 | ||
| Nut Retainer, Pix Tube Mtg. (4) | 33-494-01 | R3114 | Vv | R 5K | QVZ3234-053 | C1412 | E | Cap. | 3.3uF 160V A | QEWS52CA-335 | ||
| Clip—P.C.B. Support | 33-629-02 | R3115 | Vv | R 5K | QVZ3234-053 | C1508 | PP Cap. 5600uF SOV J | QFP31HJ-562 | ||||
| Standoff | 33-670-010R-02 | R3116 | OM | R 10KQ2WJ | QRGO29J-103 | Aci512 | APP Cap. 2000pF DC1500VJ | ~QFZ0082-202 | ||||
| Wire Terminal (Gnd. Strap) | 34-228-03 | R3117 | OM | R 10Ka2wy | QRGO29J-103 | Aci513 | APP Cap. 2000pF DC1500V. J | QFZ0082-202 | ||||
| Terminal Lug (Gnd.) | 34-33-04 | R3118 | OM | R 10KQ2WJ | QRGO29J-103 | AC1514 | APP Cap. 2000pF DC1500VJ | QFZ0082-202 | ||||
| Groundstrap Assy. | 34-574-02 | R3119 | Comp.R 3.3KQ%W K | QRZ0039-332 | C1515 | PP Cap.0.53uF DC1200VJ | QFZ0067-534 | |||||
| Grounding Spring | 35-212-03 | R3120 | Comp.R 3.3K2%W K | QRZ0039-332 | ©1820 | BPE Cap. 3.3uF 50V A | QEN61HA-335Z | |||||
| Wire Hook (Gnd. Strap) | 35-3053-02 | R3121 | Comp.R 3.3KQ%W K | QRZ0039-332 | C1523 | E | Cap. 1uF 160VA | QEW62CA-105Z | ||||
| Purity Shield Holddown Clamp — 35-2348-01 | Gapactors | C1524 | M_ | Cap. 0.1uF 200V K | QFM720K-104M | |||||||
| Support Brkt. RH | 35-3890-01 | Symbol | Description | Part Number | AC1531 | APP Cap. 2000pF DC1500V J | QFZ0082-202 | |||||
| Support Brkt. LH | 35-3890-02 | C3107 | E | Cap. | 10uF 250VA | QEWS3EA-106 | Ac1532 | APP Cap. 1500pF DC1500VJ | QFZ0082-152 | |||
| Chassis Base | 38-449-02 | 3108 | © | Cap. 1000pF DC1400VP | —QCZ9001-102M | C1904 | E | Cap. | QEY0034-001 | |||
| Yoke Wedge (3) | 39-1233-01 | C1905 | E | Cap. 10uF 250V A | QEWS52EA-106 |
o a
Les Mot X10! XIOS ond XIOS VIDEO AMR, 2SC454C c, z8c1685, jc
areas SU-1103A MAIN PCB ASSY ToexiGS RGB VIDEO Ou Ingo uTPUT or ascisiay x10 aa tated
\ XRAY XS01 H.DRIVE Ol our
- XcRay PROTECTOR 28cis07 KE, 2sces7iv 250898 or 1.08 orastiee B5Czeii or BSCz60BK 250869 ACI20V 60Hi/50nz 310%
6-16 G07-FBO
00-4147-03 Schematic Notes Unless otherwise specified Resistance: (Q) (K-KQ, M-~M&2), 1/4 (W) carbon resistor Capacitance: 1 or higher—~ (pF), less than 1-> (yF) working voltage -» 50 (V) ceramic capacitor Inductance: H) Electrolytic Cap: Capacitance Value ( F)/working voltage (V), NP — non-polar (or bipolar) electrolytic cap. Refer to the parts list for additional component information. indicates test point connection oh indicates chassis ground unless otherwise specified Hz indicates cycles per second For safety purposes (and continuing reliability) A replace all components marked with safety symbol with identical type.
Parts identification on circuit boards: e.g. SU1126A (R107 = R1107) $U3030A (R113 = R3113)
REPLACEMENT PARTS LIST—ELECTROHOME 13" MONITOR
Components identified by the A symbol in the PARTS LIST and on the Schematic have special characteristics
DO NOT degrade the safety of the set through improper servicing.
Abbreviations for Resistors and Capacitors
Resistor Capacitor
| CR | : | Carbon Resistor | C Cap. | Ceramic Capacitor |
| Comp. R | Composition Resistor | M Cap. | Mylar Capacitor | |
| OMR | : | Oxide Metal Film Resistor | E Cap. | Electrolytic Capacitor |
| VR | : | Variable Resistor | BP E Cap. | Bi-Polar (or Non-Polar) |
| MFR | : | Metal Film Resistor | Electrolytic Capacitor | |
| CMF R | : | Coating Metal Film Resistor | MM Cap. | Metalized Mylar Capacitor |
| UNFR | Nonflammable Resistor | PP Cap. | Polypropylene Capacitor | |
| FR | : | Fusible Resistor | MPP Cap. | Metalized PP Capacitor |
PS Cap. Polystyrol Capacitor Tan. Cap. Tantal Capacitor
Use of substitute replacement parts which do not have the same safety characteristics as specified, may create shock, fire or other hazards. For maximum reliability and performance, all parts should be replaced by those having identical specifications.
SERVICE REPLACEMENT PARTS LIST Main P.C.B. Ass'y (SU-1103A) Parts List
Resistors
| Symbol Description | Part Number | Symbol —_ Description | Part Number | |||
| Main RC.B. Assy | SU-1103A | 1406 | Vv | -R 2000 | QVz3230-022 | |
| CRT Socket PCB. Assy | SU-3016A | R1408 | VR 2002 | QVvz3230-022 | ||
| ; | . | R1410 | CMF R 6.801WJ | QRX019J-6R8 | ||
| Outside of the P.C.B. Ass'y | RI414 | OM | R 33ka1WJ | QRGO19J-332 | ||
| Symbol Description | Part Number | R1415, | OM | R 2.7KO1WJ | QRGO19J-272 | |
| Avo1 | Picture Tube 13" | 370ESB22(E) | 1421 | OM | R 12k92WJ | QRGO29J-123 |
| ADYO1 ADeflection Yoke | ©29123-V | R1422 | VR 10KQ | QVZ3224-014H | ||
| PC Magnet | A76366-A | AFR1401 | AF — R 6822WK | QRHO24K-680M | ||
| Wedge | 30006 | AR1503. | ACMF R 11.80%W +1% | QRV142F-1182 | ||
| ‘Flyback Transf. | A19183-A | 1504 | VR 8KO | QVZ3230-053 | ||
| AR11 | AFocus VR | ‘A46606-A | R1509 | OM | R 10K22WJ | QRGO29J-103 |
| AROS | —_UNF Resistor 2202,25W. K | QRF258K-221 | Ris | OM | R 5.6K02N Jd | QRGO29J-562 |
| Aco4 | AC Capacitor 150pF | AC1.SKV — QCZ0101-005 | R1514 | OM | R 68022WJ | QRGO20J-681 |
| X01 | _Si. Transistor | 2SD869 | R1515 | CMF R 8&201WJ | QRX019J-8R2 | |
| \Co1 | IC Regulator | STR383 | 1522 | CMF R 4.701WJ | QRX019J-4R7 | |
| Lot | —__Degaussing Coil | 21-1007-31 | R1523 | OM | R s602WJ | ORGO29J-560 |
| Degaussing Coil Pin Terminal (2) 34-708-01 | 1528 | OM | R 39021WJ | ORGO19J-391 | ||
| Degaussing Coil Pin Terminal | R1534 | ZN | OR | ERZ-CO5ZK471 | ||
| Housing | 34-709-01 | vR1501 | ZN | R | ERZ-COSDK271 | |
| Groundstrap Assy | 34-697-04 | AR1703. | ACMF R 39Ka%W +1% | QRV122F-3902 | ||
| Groundstrap Wire Terminal | 34-228-03 | AR1704. | = ACMF R 7.68KO%W+1% | — QRV142F-7681 | ||
| Groundstrap Spring (2) | 35-3560-01 | AR1901 — APosistor | A75414 | |||
| BR | Support Bracket RH | 35-3919-01 | R1902 | UNF R 207WK | QRFO76K-2RO | |
| BR | Support Bracket LH | 35-3919-02 | 1903 | CMF R 5.603WJ | QRX039J-5R6 | |
| sc | SCREW 10-% Pix Tube Mtg. (4) | 31-631018-08 | R1904 | OM | R 10KQ2WJ | QRGO26J-103Z |
| WA | Pyramidal Lockwasher (4) | 33-255-01 | AFRi901. | AF | R 2202%W K | QRH124K-221M |
Clip RC.B. Support (2) 33-629-02 Ground Lug 34-33-04
| CH | Chassis Base | 38-452-01 |
Main P.C.B. Ass'y (SU-1103A) Parts List Capacitors Symbol Description C1402 Tan. Cap, 2.2uF 16V K
| C1411 | E | Cap. 100uF 160VA |
| Ci412 | E | Cap. 3.3uF 160VA |
C1508 PP Cap. 5600pF 50V J
| C1611 | E | Cap. 47uF 160V A |
AC1512 APP Cap. 2000pF DC1500V J AC1813_ APP Cap. 2000pF DC1500V J AC1514 APP Cap. 2500pF DC1500V J C1515 PP Cap. 0.53uF DC1200V K C1520 BPE Cap. 1uF 5OVA
| C1524 | M_ | Cap. 0.1uF 200V K |
| C1904 | E | Cap. |
| C1905 | E | Cap. 10uF 250V A |
A.c1907- AMM Cap. 0.1uF AC150V Z
Coils Symbol Description L1501 Peaking Coil 11502 Liniarty Coil L1503 Width Coil 11504 Heater Choke 11901 Line Filter
‘Transformers Symbol Description T1501 Hor. Drive Trans. T1503 Side Pin Transf.
Semiconductors Symbol Description 1C1501 Lc. X1101 Si. Transistor X1102 Si. Transistor X1103 Si. Transistor X1104 Si. Transistor X1105 Si. Transistor X1106, Si. Transistor X1301 Si. Transistor X1302 Si. Transistor 1303 Si. Transistor X1304 Si. Transistor X1305 Si. Transistor X1401 Si. Transistor X1402 Si. Transistor X1501 Si. Transistor X1701 Si. Transistor D1101 Si. Diode D1102 Si. Diode D1103 Si. Diode D1301 Si. Diode D1401 Si. Diode D1402 Zener Diode D1503 Si. Diode D1504 Si. Diode D1505 Zener Diode D1506 Si. Diode D1507 Si. Diode 01508 Si. Diode 4D1701 ~~ AZener Diode AD1901 ASi. Diode 4D1902_~—- Ai. Diode AD1903_— ASi. Diode Ap1904 ~— ASi. Diode
Miscellaneous Symbol Description A\F1901 Afuse 1A AF1902 AAUL Fuse 3A Part Number QEES1CK-225B QEW52CA-107 QEW52CA-335 QFP31HJ-562 QEWS52CA-476S QFZ0082-202 QFZ0082-202 QFZ0082-252 QFZ0067-534 QEN61HA-105Z QFM72DK-682M QEY0034-001 QEWS2EA-106 QFZ9008-104
Part Number A75360-6 39934 C30380-A C30333-A A39475-J
Part Number A46022-BM C39050-A,
Part Number HA11244 2SC1685(R) 2SA673(C) 2SC1685(R) 28A673(C) 2SC1685(R) 2SA673(C) 28C1685(R) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SC1685(R) 280478 2SD478 2SC2610BK 2SC1685(P-S) WO6A WO6A WO6A 182473H 182473H RD10F(C) HF-1 VOsE RD11E(B) WO6A 1SS81 182473H D20Ev2 181887A 181887A 181887A 181887A
Part Number QMF53U1-1ROS QMF66U1-3ROS Resistors Symbol Description R3105 VR 2002 R3106 VR 2002 R3113 VR SKQ R3114 VR SKA R3115 VR S5KQ R3116 OM R 10K22W J R3117 OM R 10KQ2W J R3118 OM R 10KQ2W J R3119 Comp. R 3.3K2%W K R3120 Comp. R 3.3KQ%W K R3121 Comp. R 3.3K2%W K
Capacitors Symbol Description C3107 E Cap. 10uF 250V A C3108 C Cap. 1000pF DC1400V P
Coils Symbol Description 13101 Peaking coil
Semiconductors Symbol Description X3101 Si. Transistor 3102 Si. Transistor X3103 Si. Transistor
Miscellaneous Symbol Description A CRT Socket CRT Socket P.C.B. Ass'y (SU-3016A) Parts List
Part Number QVZ3234-022 QVZ3234-022 QVZ3234-053 QVZ3234-053 QVZ3234-063 QRG029J-103 QRGO28J-103 QRGO29J-103 QRZ0039-332 QRZ0039-332 QRZ0039-332
Part Number QEWS2EA-106 QCZ9001-102M
Part Number QQL043K-101
Part Number 2802611 28C2611 2802611
Part Number A75522
TO YOKE
| —-- | ee | _-- | _— | a | a | _ |
2A : H \ iB Ds
| \ | went, Low | ge | |
| TWIST CABLE | | [ | a | - |
| | | rc | 1 |
on
| (ever. ge | VERT. Ht | | | am | eo | | | | | |
| a | ig, Ar | + | |||||
| al. | M40 | : | 32 | Driver | ||||
| a | | | ey | cise | Drete | | | ||
| |363|__ year. ve He. | ame! | 4 = | H | ||||
| shiflie | | 4 | czise | Nersove kaze Ra2504 noZee | wp dese 3) UY | | | |||
| | | Jeers [eano *[ 36V | 1 | + Tiss | Bee Eee? 3) d | | |||
| 990 | pear fezuso | | Li Jew J | F | fim fa 31 3 | | |||
| ' vaya | | | | ' | ve | t | s BIT 3 | i | _ ‘ * i} |
| breed tt? | j | sesame “SE | 7 | Yorsz0s + B8i? | | | |||
| cae | aai05 | | i J } | tert _ | | | |||
| eed | sak, | 77 | re" aaa | | | | ||||
| ed | =| | Fs | = TF aTore | ||||
| a | iF | rey | ed ee | | 298, | ' | ||
| | | — | oe | a | 121-1040 |
a Teazay REVERSE
| I | caaia §2-2 | DRIVE | ||||
| ' | = | Te | ||||
| ! | oo — | | | ca T | |||
| oe | ~ | = | | | |||
| &® | grea Legos | . | | | |||
| waiiosy f O* — | a | vor, wi | | | |||
| oo | Hae | | WY fo | eee | ’ | | | |
| nazis, |.c3208 | 93208 | DRIVER | 3) SHEEP | om a | | | |||
| fm er | 121-973 | axs202 | ? | Pra | ensz05 | ope | | | |
| SHUTOOHN | [21-975 | 4 | +s) | 26Kv | ae | | |
| L_ | a | wseos,_ 3207 L.tgaaa { | < PeKY | |||
| I | = | + | 5 T: | \ | ||
| aia [éxdoa | 3262 | cna206 | pb | 4/ | VOLTAGE | \ |
| | | ee | we |
zen ettios peau
| = | Rx3209 yi | SE) Pewaeas Ta, | I | |||
| r | | | axa2t | m | 13208 | 3 | gPSE* | cxsz0 | | |
| vavsu | | ieee | ey ees | i | | | ||
| 2 | sgo20 DP lewszeo teres dmans) PSs | i | ||||
| — | i | 3610 pxg206 | ai fe fi [owe L | 5 | | | |
| 43« 733K Sexaai7 | = = | 12K ~ | | | |||
| | | vm Tie BET can | i | on | |||
| | | cxaais | 124 STD raze: | iin | | | | |
sty jes.sues
| \ | [ ee | i 4 |
,
Ln Buen | 303) NE ‘RN
| sone | | | \ | ||
| ! | t—— | — | | | | |
| : | ] | i | ||
| sgh | — | _ | —_ | i} |
oe i
i |
j |
| Saal 2} gr | | _ | a | 9-186-05 | | | |
| 7 | el. | 7 | oo | 4} | |
| = | — | —— | _. | — | | |
| [7] one croune | “s | Weawise Secu |
6-18 YacICLIORS ERE IN MILROFARADS ULES (iawise sPeciFIeD VW + —_={ va or’ | ox3229, ri
canit _| 1 |
- pen | | mein
| 1 | i ae | i |
i | 1 |
L -_ J
REFERENCE ONLY
SCHEMATIC FOR G- 186-02 SWEEP BOARD _RGB_COLOR MONIT! ISSUE ZENITH RADIO CORP. CHICAGO, ILL. B | 93-186 M05 1-00087-A021
NOTES: (USED WITH CIRCUIT REFERENCE De: 2 bne See bans IGT FOR APPLiCABl waroRs Se) oS lumpei wise useo ©. -# © e— Provision ow PRIUTEE ciRCL: scare,
SWEEP BOARD (9-186-03)
| Ref. No. | Part No. | Description | Ret. No. | PartNo, | Description |
CAPACITORS TRANSFORMERS & COILS
| 2131 | 22-7508 | 47 MF, 38V, +20% Electrolytic | .3207 | 149-454 | Core, Ferrite Bead | ||
| 2152 | 22-7508-01C | 22 MF, 38V, +20% Electrolytic | 3220 | F-13834 | Core & Sleeving Assy. (149-509-01) | ||
| 3201 | 22-7410-05 | 10 MF, 100V, +20% Electrolytic | LxS261 | 20-3976 | Coil Width | ||
| xs202 | 22-7710-01C | 1 MF, 50V, +50%~10% Electrolytic | LXx3262 | 20-3975 | Coil, Linearity, with 205-271 Hot Melt | ||
| 3203 | 22-7711-08C | 47 MF, 63V, +50%~10% Electrolytic | 73205 | 95-3344 | Fransformer, Horizontal Driver | ||
| Cx3204 | 22-7773-24A | 0.1 MF, 100V, 6% Polyester | 7x3204 | 95-3561-01 | Transformer, Sweep | ||
| x3205 | 22-7523-01 | 0.01 MF, 2KV, +20% Disc | |||||
| 63206 | 22-7708-04C | 4.7 MF, 25V, +50%—10% Electrolytic | RESISTORS | ||||
| ©3207 | 22-5665 | 330 PF, 1000, 10% Disc | 105 | 9021-94 | 8.2 | £50 | 1/4W Film |
| ©3208 | 22-7242 | 0.0018 MF, 200V, +10% Disc | hone | tcoslet | a70k ON, Tem/aweiin | ||
| 3211 | 22-7777-20B | 0.047 MF, 200V, + 10% Polyester | R2111 | 63-9919-83 | 3K Ohm, +2% 1/4W Film | ||
| ca2i2 | 22-7234 | 560 PF. SOOV, | =10% Disc | R2112 | 63-9919-98 | 10K Ohm, +2% 1/4W Film | |
| 63213 | 22-T775-16A | 0.022 MF, 100V, +20% Polyester | AXg204 | 63-9921-80 | 2.2K Ohm, +5% 1/4W Film | ||
| 3214 | 22-7775-10A | 0.0068 MF, 100V, +20% Polyester | RX3206 | 63-7805 | 3.3K Ohm. -+8% 1/2W Carbon | ||
| eck | 22-5684 | 470 PF, SOOV, +20% Disc | RX3207 | 63-9921-32 | 22 Ohm, +5% 1/4W Film | ||
| 3217 | 22-5084 | 470 PF, S00V, +20% Disc | RX3208 | 63-10235-80 | 2.2K Ohm, +5% 1/4W Film | ||
| 3218 | 22-7774-15C | 0.018 MF, 100V, +10% Polyester | AX3209 | 63-10235-72 | 1K Ohm, 5% 1/4W Film | ||
| 3222 | 22-7742-10 | 0,001 MF, SOV, +10% Axial | RX3210 | 63-7805 | 3.3K Ohm, +5% 1/2W Carbon | ||
| oxs228 | 2er6466 | 530 PF, SKV, £10% Disc | RX3211 | 63-10810-07 | 3K Ohm, +1% 1/2W Film | ||
| x3229 | 22-7672-07 | 0.013 MF. 1.6KV, +5% Polypropylene | RX3214 | 63-10233-81 | 2.4K Ohm, 42% 1/4W Film | ||
| C3233 | 22-7728 | 0.68 MF, 200V, £10% Polyester | RX3216 | 63-10810-06 | 1.2K Ohm, +1% 1/2W Film | ||
| 03244 | 22-7566-24 | 0.1 MF, 250V, #10% Polyester | RX3217 | 63-7760 | 270 Ohm. 5% 1/2W Carbon | ||
| ©3261 | 22-7683-01 | 0.68 MF, 200V, +5% Polypropylene | RX3215. | 63-10235-98 | 12K Ohm, +5% 1/4W Film | ||
| AX3218 | 63-10235-82 | 2.7K Ohm, +5% 1/4W Film | |||||
| SEMICONDUCTORS | RX3219 | 63-10235-88 | 4.7K Ohm, +5% 1/4W Film | ||||
| R3202 | 103-142-01 | Diode, Low Voltage | 3224 | 63-9946-88 | 4.7K Ohm, 5% 1/2W Film | ||
| CR3203, | 103-330A | Diode, Low Voltage | 3225 | 63-10836-68 | 680 Ohm, +5% 2W Wire Wound | ||
| CRX3204 | 103-3084 | Diode, Zener | 3226 | 63-10235-74 | 1.2K Ohm, +5% 1/4W Film | ||
| CR3205 | 403-305 | Diode, Damper | 3227 | 63-10235-80 | 2.2K Ohm, +5% 1/4W Film | ||
| CR3206 | 103-2844 | Diode. Low Voltage | RRX3235 | 63-10810-06 | 1.2K Ohm, +1% 1/2W Film | ||
| R3207 | 103-295-01A | Diode, Low Voltage | RX3240, | 53-10857-04 | 10 Meg Ohm, | +20% 1/2W Carbon | |
| (used with 149-454) | 3242 | 63-10243-80 | 2.2K Ohm, +5% 1/2W Film | ||||
| ©R3208 | 103-295-01A | Diode, Low Voltage | R3243 | 63-10243-80 | 2.2K Ohm, +5% 1/2W Film | ||
| CR3209 | 103-142-01 | Diode, Low Voltage | 3244 | 63-7868, | 100K Ohm, +5% 1/2W Carbon | ||
| CR3210 | 403-142-01 | Diode, Low Voltage | 3261 | 63-10444-86 | 390 Ohm, +10% SW Wire Wound | ||
| R321 | 103-142-01 | Diode, Low Voltage | 3262 | 63-10565-65 | 510 Ohm. +10% 1/2W Film | ||
| Qx3202 | 121-975 | Transistor, NPN | 3263 | 63-10565-65 | 510 Ohm, | +10% 1/2W Film | |
| Qx3204 | 121-973 | Transistor, PNP, Shutdown | 3282 | 63-10235-96 | 10K Ohm, +5% 1/4W Film | ||
| 3206 | 121-1037 | Transistor, NPN, Forward Driver | |||||
| QX3207 | 121-975 | Transistor, NPN, Shutdown | |||||
| 3209 | 121-1040 | Transistor, NPN, Reverse Driver |
ZENITH MONITOR — SWEEP BOARD REPLACEMENT PARTS LIST
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
ZENITH MONITOR — MAIN BOARD REPLACEMENT PARTS LIST MAIN BOARD (Continued)
Board Board
| 9-227 | 9-227 | 9-227 | Ret. No. | Part No. | Description | |||||||||||
| 9-227 | -01 | Ref.No. PartNo, | Description | 9-227 | -01 | Ref.No. PartNo. | Description | 9-227 | -01 | Ref.No. PartNo. | Description | CAPACITORS | a | |||
| RESISTORS | RESISTORS (Continued) | RESISTORS (Continued) | C2101 | 22-7775-10A | 0.0068 MF, 100V +20% Polyester | |||||||||||
| x | X | RX2101 63-10565-32 | 22 Ohm, +5%, 1/2W Film | X | 2518 | 63-10235-73 | 1.1K Ohm, +5%, 1/4W Film | x | X | 3222 | 63-10235-40 | 47 Ohm, +5%, 1/4W Film | C2102 | 22-7775-24A | 0.1 MF, 100V +20% Polyester | |
| x | X | 2102 | 63-10243-56 | 220 Ohm, +5%, 1/2W Film | x | R2519 | 63-10235-93 | £5%, 1/4W Film | x | X | 3231 | 63-9982 | 1 Ohm, £10%, 2W Wirewound | C2103 | 22-7709-09C | 100 MF, 35V +50%~10% Electrolytic |
| x | X | R2103 | 63-10235-88 | 4.7K Ohm, +5%, 1/2W Film | X | R2519 | 63-10235-82 | £5%, 1/4W Film | x | X | 3233 | 63-10565-14 3.9 Ohm, +5%, 1/2W Film | C2104 | 22-7613-24D | 0,01 MF, SOV 410% Disc | |
| x | X | RX2104 63-10243-11 | 3 Ohm, +5%, 1/2W Film | x | R2520 | 63-10235-80 | £5%, 1/4W Film | x | X | R3234 | 63-10585-14 3.9 Ohm, +5%, 1/2W Film | C2105 | 22-7390-02 | 0.47 MF, 50V +20% Electrolytic | ||
| x | X — RX2105 63-10243-11 | 3 Ohm, +5%, 1/2W Film | x | R2521 | 63-10235-50 | 120 Ohm, +5%, 1/4W Film | x | X | 3239 | 63-10244-20 | 100K Ohm, +5%, 1/2W Film | C2106 | 22-7710-07G | 33 MF, 50V +50%-10% Electrolytic | ||
| x | X | R206 | 63-10235-72 | 1K Ohm, +5%, 1/4W Film | X | R2521 | 63-10235-48 | 100 Ohm, +5%, 1/4W Film | x | X | 3241 | 63-8246 | 4 Ohm, 10W Wirewound | C2107 | 22-7615-03D | 0.0033 MF, SOV +80%-10% Disc |
| x | X | R2107 | —63-10235-66 560 Ohm, | +5%, 1/4W Film | x | R2522 | 63-10235-74 | 1.2K Ohm, +5%, 1/4W Film | x | X | 3244 | 63-10840-40 47 Ohm, +5%, 3W Film, | 2110 | 22-7742-10 | 0.001 MF, SOV +10% Polyester | |
| x | X | 2108 | 63-10235-66 560 Ohm, | +5%, 1/4W Film | x | R2523 | 63-10238-28 220K Ohm, +5%, 1/4W Film | Tin Oxide | 2111 | 22-7774-17A | 0.027 MF, 100V +10% Polyester | |||||
| x | X | R2109 | 63-1565 | 1 Ohm, + 5%, 1/2W Film | X | R2523 | 63-10236-52 2.2 Meg Ohm, +5%, 1/4W Film | x | X | 3245 | 83-10710A_—Thermistor | C2176 | 22-7725 | 680 MF, 50V +100%-10% Electrolytic | ||
| x | X | R2110 | 63-10565 | 1 Ohm, +5%, 1/2W Film | x | X | R2524 | 63-10235-90 5.6K Ohm, +5%, 1/4W Film | x | X | RX3246 63-10657-03 | 1.2 Meg Ohm, +20%, | C2501 | 22-7621-42C | 220 PF, 50V +5% Disc | |
| x | X | R2111 | 63-10565 | 1 Ohm, +5%, 1/2W Film | x | R2525 | 63-10235-56 220 Ohm, +5%, 1/4W Film | 1/2W Carbon | 2502 | 22-7821-42C | 220 PF, 50V +5% Disc | |||||
| x | X | 2112 | 63-10565 | 1 Ohm, +5%, 1/2W Film | X | 2525 | 63-10235-58 | 270 Ohm, +5%, 1/4W Film | X | 3260 | 63-10243-96 | 10K Ohm, +5%, 1/2W Film | C2503 | 22-7621-42C | 220 PF, 50V +5% Disc | |
| x | X | R2113_ | 63-10243-60 330 Ohm, | +5%, 1/2W Film | x | R2526 | 63-10235-80 | 2.2K Ohm, +5%, 1/4W Film | X | R3261 | 83-10244-24 150K Ohm, +5%, 1/4W Film | C3204 | 22-7775-244 | 0.1 MF, 100V +20% Polyester | ||
| x | X | 2114 | 63-10235-72 | 1K Ohm, +5%, 1/4W Film | X | 2526 | 63-10235-69 | 750 Ohm, +5%, 1/4W Film | X | 3262 | 63-10235-68 680 Ohm, +5%, 1/4W Film | C3204 | 22-7603 | 4.7 MF, 315V +100%~10% Electrolytic | ||
| x | X | 2115 | 63-10235-88 4.7K Ohm, +5%, 1/4W Film | x | R2527 | 63-10857-31 | 5K Ohm, Control-Rotary | x | X | 3401 | 63-10236-46 | 1.2 Meg Ohm, +5%, 1/4W Film | C3205 | 22-3512 | 0.01 MF, 1KV +40%-20% Disc | |
| x | X | R2116 | 63-10235-60 330 Ohm, +5%, 1/4W Film | Single-Blue | x | X | R3402_ | 63-10236-22 | 120K Ohm, +5%, 1/4W Film | 3206 | 22-7603-01A | 10 MF,315V +100%~10% Electrolytic | ||||
| x | X | R2117 | 63-10235-80 2.2K Ohm, +5%, 1/4W Film | X — R2527 | 63-10857-26 800 Ohm, Control-Rotary | x | X | 3403 | 63-10235-86 | 3.9K Ohm, +5%, 1/4W Film | 3207 | 22-7742-10 | 0.001 MF, 50V +10% Axial | |||
| x | X | R2118 | 63-10235-88 | 4.7K Ohm, +5%, 1/4W Film | Single-Blue Cut-Off | x | X | R3404 | 63-10235-86 | 3.9K Ohm, +5%, 1/4W Film | 3208 | 22-7742-10 | 0.001 MF, 50V +10% Axial | |||
| x | X | 2119 | 63-10235-54 | 180 Ohm, +5%, 1/4W Film | x | R2528 | 63-10857-30 | 1K Ohm, Control-Rotary | x | X | 3405 | 63-10236-08 33K Ohm, +5%, 1/4W Film | 3209 | 22-7395 | 470 PF, 500V +5% Disc | |
| x | X | R2120 | 63-10565-08 2.2 Ohm, +5%, 1/2W Film | Single-Yellow | x | X | R3406 | 63-10235-68 680 Ohm, +5%, 1/4W Film | 3234 | 22-7395 | 470 PF, 500V +5% Disc | |||||
| x | X | 2121 | 63-10243-52 | 150 Ohm, +5%, 1/2W Film | X | 2528 | 63-10857-26 800 Ohm, Controi-Rotary | x | X | 3407 | 63-10236-18 82K Ohm, +5%, 1/4W Film | 3236 | 22-7861-14 | 2200 MF, 35V +20% Electrolytic | ||
| x | X | R2122 | 63-10243-52 | 150 Ohm, +5%, 1/2W Film | Single-Blue Drive | x | X | R3408 | 63-10236-04 22K Ohm, +5%, 1/4W Film | C3246 | 22-7603-01A | 10 MF, 315V +100%~10% Electrolytic | ||||
| x | X | R2125 | 63-9023-02 | 550 Ohm, +20%, Control- | x | R2529 | 63-10235-76 | 1.5K Ohm, +5%, 1/4W Film | Xx | X | R3409 | 63-10857-17 | 100K Ohm, Control-Rotary | C3247 | 22-7860-12 | 470 MF, 25V +20% Electrolytic |
| Rotary Single-GRA | X | 2529 | 63-10235-75 | 5%, 1/4W Film | Single-Green | 3249 | 22-7431-06 | (0.0047 MF, +20% Disc | ||||||||
| X | R2126 | 63-10243-66 | 560 Ohm. +5%, 1/2W Film | x | R2530 | 63-10235-93 | 3%, 1/4W Film | x | X | R3410 | 63-10236-31 | 300K Ohm, +5%, 1/4W Film | CX3250 | 22-7431-06 | 0.0047 MF, +20% Disc | |
| x | R2126 | 63-10243-53 | 160 Ohm, +5%, 1/2 Film | X | R2530 | 63-10235-82 | %, 1/4W Film | x | X | R3411 | 63-10236-03 | 20K Ohm, +5%, 1/4W Film | 03251 | 22-7811 | 0.001 MF, 1KV +10% Disc | |
| X | R2127 | 63-10243-69 | +5%. 1W Carbon | x | R2531 — 63-10235-80 | 5%, 1/4W Film | x | X | 3412 | 63-10236-13 51K Ohm, +5%, 1/4W Film | 03252 | 22-7811 | 0.001 MF, 1KV £10% Disc | |||
| x | 2128 | 63-10243-66 | £5%, 1/2W Film | x | R2532 | 63-10235-50 | 120 Ohm, +5%, 1/4W Film | x | X | 3413. | 63-10236-07 30K Ohm, +5%, 1/4W Film | C3253 | 22-7811 | 0.001 MF, 1KV 10% Disc | ||
| X | 2128 | 63-6058 | 5%, 1W Carbon | X | 2532 | 63-10235-48 | 100 Ohm, +5%, 1/4W Film | x | X | R3414_ | 63-10235-98 | 12K Ohm, +5%, 1/4W Film | 3254 | 22-7404-06 | 22 MF, 16V +20% Electrolytic | |
| X | R2129 | 63-10243-65 | 5%, 1/2W Carbon | x | R2533 | 63-10235-74 1.2K Ohm, | +5%, 1/4W Film | x | X | R3415 | 63-10236-02 | 18K Ohm, +5%, 1/4W Film | C3256 | 22-7508-05B | 2200 MF, 35V +50%~10% Electrolytic | |
| x | R2501 | 63-10236-28 | £5%, 1/4W Film | R2534 | 63-10235-52 | 150 Ohm, +5%, 1/4W Film | x | X | R3417 | 63-10243-60 330 Ohm, +5%, 1/2W Film | C3257 | 22-7395 | 470 PF, 500V +5% Disc | |||
| X | 2501 | 63-10236-52 | 2.2 Meg Ohm, +5%, 1/4W Film | x | R2535 | 63-10235-52 | 150 Ohm, +5%, 1/4W Film | x | X | 3418 | 63-10857-08 2K Ohm, Control-Rotary | 3401 | 22-7613-24D | 0.01 MF, 50V +10% Disc | ||
| x | X | R2502 | 63-10235-90 | 5.6K Ohm, +5%, 1/4W Film | x | R2536 | 63-10235-52 | 150 Ohm, +5%, 1/4W Film | Single-Yellow | 3402 | 22-7406-01 | 1.0 MF, 35V +20% Electrolytic | ||||
| x | R2503 | 63-10235-56 220 Ohm. #:5%, 1/4W Film | x | R2537 | 63-10235-52 | 150 Ohm, +5%, 1/4W Film | x | X | 3419 | 63-10235-84 3.3K Ohm, +5%, 1/4W Film | £3403 | 22-7773-18A | 0.033 MF, 100V +5% Polyester | |||
| X | R2503 | 63-10235-58 270 Ohm, +5%, 1/4W Film | x | R2538 | 63-10235-56 220 Ohm, +5%, 1/4W Film | x | X | 3420 | 63-10236-10 39K Ohm, +5%, 1/4W Film | 63404 | 22-7773-17A | 0.027 MF, 100V +5% Polyester | ||||
| x | R2504 | 63-10235-80 2.2K Ohm, +5%, 1/4W Film | XK | R2538 | 63-10235-48 | 100 Ohm, +5%, 1/4W Film | x | X | 3421 | 63-10235-73 | 1.1K Ohm, +5%, 1/4W Film | 3405 | 22-7775-10A | 0.0068 MF, 100V +20% Polyester | ||
| X | R2504 | 63-10235-69 | 750 Ohm, +5%, 1/4W Film | x | R2539 | 63-10235-56 220 Ohm, +5%, 1/4W Film | x | X | R3422 | 63-10243-60 330 Ohm, | +5%, 1/2W Film | C3407 | 22-7710-01A | 1.0 MF, 50V +50%~10% Electrolytic | ||
| x | R2505 | 63-10857-11 | 5K Ohm, Control-Rotary | X | 2539 | 63-10235-48 | 100 Ohm, +5%, 1/4W Film | x | X | R3423° | 63-10243-60 330 Ohm, | +5%, 1/2W Film | C3409 | 22-7709-09C | 100 MF, 35V +100%~10% Electrolytic | |
| Single-RED | x | 2540 | —63-10235-56 | 220 Ohm, +5%, 1/4W Film | x | X | 3424 | 63-10235-72 | 5%, 1/4W Film | 3410 | 22-7404-06A | 22 MF, 16V +20% Electrolytic NP | ||||
| X | R2505 | 63-10857-27 | 800 Ohm, Control-Rotary | X | R2540 | 63-10235-48 | 100 Ohm, +5%, 1/4W Film | x | X | 3425 | 63-10235-88 4.7K Ohm, +5%, 1/4W Film | c34it | 22-7708-09 | 100 MF, 25V +50%~10% Electrolytic | ||
| Single-Red Cut-Off | X | 2541 | 63-10235-54 | 180 Ohm, +5%, 1/4W Film | x | X | R3428 | 63-10235-82 2.7K Ohm, +5%, 1/4W Film | C3412 | 22-7710-01C | 1.0 MF, 50V +50%~10% Electrolytic | |||||
| x | R2506 | 63-10857-30 | 1K Ohm, Control-Rotary | X | 2542 | 63-10235-53 | 160 Ohm, +5%, 1/4W Film | x | X | 3429 | 63-10235-76 | 1.5K Ohm, +5%, 1/4W Film | C3413 | 22-7562-32 | 0.47 MF, 100V +5% Polyester | |
| Single-Yeliow | X | 2543 | 63-10235-54 | 180 Ohm, +5%, 1/4W Film | x | X | R3431 | 63-10235-80 2.2K Ohm, +5%, 1/4W Film | C3414 | 22-7774-16A | 0.022 MF, 100V +10% Polyester | |||||
| X | R2506 | 63-10857-27 | 800 Ohm, Control-Rotary | X | 2544 | 63-10235-54 | 180 Ohm, +5%, 1/4W Film | x | 3432 | 63-10235-55 200 Ohm, +5%, 1/4W Film | 3419 | 22-7751-39 | 180 PF, 50V +5% Axial | |||
| Single-Red Drive | X | R2545 | 63-10235-54 | 180 Ohm, +5%, 1/4W Film | X | R3432__63-10235-79 2K Ohm, +5%, 1/4W Film | 3420 | 22-7710-01C | 1.0 MF, SOV +50%-10% Electrolytic | |||||||
| x | R2507 | 63-10235-76 | 1.5K Ohm, +5%, 1/4W Film | X | R2548 | 63-10235-53 | 160 Ohm, +5%, 1/4W Film | x | X | R3433_ | 63-10236-20 | 100K Ohm, +5%, 1/4W Film | 3421 | 22-7773-18B | 0.033 MF, 100V +5% Polyester | |
| X | 2507 | 63-10235-75 | 1.3K Ohm, +5%, 1/4W Film | X | R2548 | 63-10235-67 620 Ohm, +5%, 1/4W Film | x | X | R3434 | 63-10236-22 | 120K Ohm, +5%, 1/4W Film | C3422 | 22-7613-24D | 0.01 MF, 50V +10% Disc | ||
| X | 2508 | 63-10235-93 7.5K Ohm, +5%, 1/4W Film | X | R2549 | 63-10235-67 620 Ohm, +5%, 1/4W Film | x | X | 3435 | 63-10235-63 430 Ohm, +5%, 1/4W Film | C3423, | 22-7613-08D | 470 PF, 50V +10% Disc | ||||
| x | R2508 | 63-10235-82 2.7K Ohm, +5%, 1/4W Film | X | 2550 | 63-10235-32 22 Ohm, +5%, 1/4W Film | x | X | 3436 | 63-10235-72 | 1K Ohm, +5%, 1/4W Film | C3424 | 22-7742-05 | 390 PF, 50V +10% Axial | |||
| x | R2503 | 63-10235-80 2.2K Chm, +5%. 1/4W Film | X | 2552 | 63-10235-32 22 Ohm, +5%, 1/4W Film | x | X | 3439 | 63-10243-79 2K Ohm, +5%, 1/2W Film | C3425 | 22-7742-10 | 0.001 MF, SOV +10% Axial | ||||
| x | R2510 | 63-10235-50 | 120 Ohm, +5%, 1/4W Film | X | 2554 | 63-10235-32 22 Ohm, +5%, 1/4W Film | x | X | R344 | 63-10235-86 3.9K Ohm, +5%, 1/4W Film | C3426 | 22-7742-10 | 0.01 MF, SOV +10% Axial | |||
| X | 2510 | 63-40235-48 | 100 Ohm, +5%, 1/4W Film | x | X — R3201 | 63-10235-59 | 300 Ohm, +5%, 1/4W Film | x | R3441 | 63-10857 | 100 Ohm, Control-Rotary | 3427 | 22-7647-35C | 150 PF, +10% Axial | ||
| x | R2511 | 63-10235-74 | 1.2K Ohm, +5%, 1/4W Film | x | X | 3202 | 63-10235-44_ | 68 Ohm, +5%, 1/4W Film | Single-Horizontal Center | 63428 | 22-7774-12 | 0.01 MF, 100V +10% Polyester | ||||
| X | R2511 | 63-10235-87 620 Ohm, +5%, 1/4W Film | x | X | 3203 | 63-10235-52 | 150 Ohm, +5%, 1/4W Film | X | 3441 | 63-10857-02 250 Ohm, Control-Rotary | C3428 | 22-7774-20A | 0.047 MF, 100V +10% Polyester | |||
| x | R2512 | 63-10236-28 220K Ohm, +5%, 1/4W Film | Xx | X | 3205 | 63-7781 | 820 Ohm, +5%, 1/2W Carbon | Single-Horizontal Center | (on-01 version) | |||||||
| X | 2512 | 63-10236-52 | 2.2 Meg Ohm, +5%, 1/4W Film | x | R3206 | F-11851 | 12 Ohm, +10%, 10W Resistor | x | X | R3442_ | 63-10235-86 3.9K Ohm, +5%, 1/4W Film | 3429 | 22-7405-04 | 4.7 MF, 25V +20% Electrolytic NP | ||
| x | X | 2513 | 63-10235-90 | 5.6K Ohm, +5%, 1/4W Film | . | & Splice Assy. | x | R3443_ | 63-10235-65 510 Ohm, +5%, 1/4W Film | 3429 | 22-7406 | 0.47 MF, 35V +20% Electrolytic NP | ||||
| x | R2514 | 63-10235-56 220 Ohm, +5%, 1/4W Film | X | 3206 | 63-10460-50 | 12 Ohm, +10%, 10W | X | 3443 | 63-10235-80 2.2K Ohm, +5%, 1/4W Film | (on-01 version) | ||||||
| X | 2514 | 63-10235-58 270 Ohm, | +5%, 1/4W Film | Wirewound | x | X | 3444 | 63-10235-60 | 330 Ohm, +5%, 1/4W Film | C3430 | 22-7613-24D | 0.01 MF, 50V +10% Disc | ||||
| x | R2515 | 63-10235-80 2.2K Ohm, +5%, 1/4W Film | x | X | 3210 | 63-10420-31 | 2 Ohm, +5%, 2W Wirewound | x | X | 3445 | 63-10235-80 | 2.2K Ohm, +5%, 1/4W Film | 63431 | 22-7774-16A | 0.022 MF, 100V +10% Polyester | |
| R2515 | 63-10235-71 | 910 Ohm, +5%, 1/4W Film | x | X | 3212 | 63-10235-76 | 1.5K Ohm, +5%, 1/4W Film | X | R3446 | 63-10235-72 | 1K Ohm, +5%, 1/4W Film | C3434 | 22-7742-08 | 470 PF, 50V +10% Axial | ||
| x | R2516 | 63-10857-32 5K Ohm, Control-Rotary | x | R3213 | 63-10235-83 3K Ohm, +5%, 1/4W Film | x | 3449 | 63-10235-76 | 1.5K Ohm, +5%, 1/4W Film | 3436 | 22-7613-24C | 0.01 MF, 100V +10% Disc | ||||
| Single-Green | X | R3213__63-10235-86 3.9K Ohm, +5%, 1/4W Film | x | R3451 | 63-10235-82 2.7K Ohm, +5%, 1/4W Film | C3450 | 22-7739-29A | 0.27 MF, 100V +10% Polyester | ||||||||
| X | 2516 | 63-10857-25 | 800 Ohm, Control-Rotary | x | X | R3214 | 63-10235-74 | 1.2K Ohm, +5%, 1/4W Film | X | 3451 | 63-10235-88 4.7K Ohm, +5%, 1/4W Film | C3450 | 22-7619-41C | 200 PF, SOV +5% Disc | ||
| Singie-Green Cut-Off | x | R3215 | 63-10244-38 560K Ohm, +5%, 1/2W Film | x | X | 3452 | 63-10235-92 | 6.8K Ohm, +5%, 1/4W Film | (on-01 version) | |||||||
| x | R2517 | 63-10857-30 | 1K Ohm, Control-Rotary | X | 3215 | 63-10244-40 680K Ohm, +5%, 1/2W Film | X | R3453 | 63-10235-75 | 1.3K Ohm, +5%, 1/4W Film | 3461 | 22-7710-01C | 1.0 MF, 50V +50%-10% Electrolytic | |||
| Single-Yellow | x | X | 3216 | 63-10244-25 | 160K Ohm, +5%, 1/2W Film | x | X | R3461 | 63-10236 | 15K Ohm, +5%, 1/4WW Film | C3462 | 22-7710-01C | 1.0 MF, 50V +50%~10% Electrolytic | |||
| X | R2517 | 63-10857-25 | 800 Ohm, Control-Rotary | x | X | R3217 | 63-10244-33 360K Ohm, | +5%, 1/2W Film | x | X | R3462 | 63-10236-13 51K Ohm, +5%, 1/4W Film | 3462 | 22-7739-08 | 0.0056 MF, 100V +10% Polyester | |
| Single-Green Drive | x | X | 3218 | —63-10235-80 2.2K Ohm, +5%, 1/4W Film | (on-0% version) | |||||||||||
| x | R2518 | 63-10235-76 | 1.5K Ohm, +5%, 1/4W Film | X | 3219 | 63-10244-38_ | 560K Ohm, +5%, 1/2W Film | C3463 | 22-7508 | 47 MF, 35V +20% Electrolytic |
6-21
MAIN BOARD (Continued)
| Ret. No. | Part No. | Description |
SEMICONDUCTORS
| cR2104 | 103-142-01 | Diode, Low Voltage |
| CR2105 | 103-254-01 | Diode, Low Voltage |
| CR2106 | 108-254-01 | Diode, Low Voltage |
| CR2107 | 103-254-01 | Diode, Low Voltage |
| CR2501 | 103-142-01 | Diode, Low Voltage |
| R2502 | 103-142-01 | Diode, Low Voltage |
| R2503 | 103-142-01 | Diode, Low Voltage |
| CR3202 | 103-330A | Diode, Low Voltage |
| CR3205, | 103-309-01 | Diode, Zener 10V 1W |
| CR3206 | 103-254-01 | Diode, Low Voltage |
| CR3208 | 103-326 | Diode, Low Voltage |
| CR3210 | 103-254-01 | Diode, Low Voltage |
| CR3211 | 103-254-01 | Diode, Low Voltage |
| R3214 | 103-284-A | Diode, Low Voltage |
| CR3217 | 103-3264, | Diode, Low Voltage |
| CR3219 | 103-330A | Diode, Low Voltage |
| CR3223, | 103-330A | Diode, Low Voltage |
| cR3224 | 103-3304 | Diode, Low Voltage |
| CR3231 | 103-315-06A | Diode |
| CR3232 | 103-315-064 | Diode |
| CR3233 | 103-315-06A | Diode |
| CR3234 | 103-315-06A | Diode |
| CR3235, | 103-2844 | Diode, Low Voltage |
| CR3401 | 103-142-01 | Diode, Low Voltage |
| CR3404 | 103-143-01 | Diode, Low Voltage |
| CR3405, | 103-142-01 | Diode, Low Voltage |
| CR3406 | 103-142-01 | Diode, Low Voltage |
| ©R3408 | 103-279-14 | Diode, Zener 6.8V 1/2W |
| 2101 | F-10896 | Transistor & Heat Sink Assy. |
| 2102 | F-10896 | Transistor & Heat Sink Assy. |
| Q2103 | 421-975 | Transistor NPN |
| Q2104 | 121-1064 | Transistor PNP. |
| 2501 | 121-1019 | Transistor PNP |
| 2502 | 121-895 | Transistor NPN |
| 2502 | 121-551 | Transistor NPN |
(on-01 version)
| 2508 | 121-1019 | Transistor PNP |
| 2504 | 121-895 | Transistor NPN |
| 2504 | 421-551 | Transistor NPN |
(on-01 version)
| 2505 | 121-1019 | Transistor PNP |
| 2506 | 121-895 | Transistor NPN |
| 2506 | 121-551 | Transistor NPN |
(on-01 version)
| a2507 | 121-1019 | Transistor |
| 92508 | 121-1019 | Transistor |
| 2509 | 121-1019 | Transistor |
| 3200 | F-12737 | Transistor & Heat Sink Assy. |
| 93201 | 121-499-01 | Transistor NPN Regular Feed Back |
| Q3202 | 121-1034 | Transistor NPN |
| Q3203 | 121-1059 | Transistor PNP |
| 93401 | 121-895 | Transistor NPN |
| 3402 | 121-986 | Transistor PNP |
| Q3403 | 121-985 | Transistor NPN. |
| Q3404 | 421-895 | Transistor NPN |
| a3405 | 121-895 | Transistor NPN |
TRANSFORMERS & COILS
| 2502 | 20-3887-01 | Coil Peaking | 1.2UH |
| 12503 | 20-3887-01 | Coil Peaking 1.2 UH | |
| 12504 | 20-3887-01 | Coil Peaking 1.2 UH | |
| 13201 | 20-2021 | Coil Peaking 100 UH | |
| LX3202 | 95-3501-01 | Transformer Choke 60 UH | |
| 3401 | 20-3831 | Coil Peaking 663 UH | |
| 3402 | 20-3998 | Coil Peaking 39 UH | |
| 13402 | 20-4026 | Coil Turnable 39 UH |
{on -01 version) ZENITH MONITOR — CRT SOCKET BOARD REPLACEMENT PARTS LIST
CRT SOCKET (9-155-10)
| Ret. No. | Part No. | Description |
CAPACITORS
| 5101 | 22-4671 | 0.01 MF, 1.5KV, +80%-20% Disc |
| C5102 | 22-3512 | 0.01 MF, 1KV, +40%-10% Disc |
TRANSFORMERS & COILS
| L5102 | 20-3887-28E | 220MH Peaking |
| 5103 | 20-3887-28E | 220 MH Peaking |
| L5104 | 20-3887-28E | 220 MH Peaking |
SEMICONDUCTORS
| Q5101 | F710 | Transistor, NPN, Video Out, Blue |
| 95102 | F7510 | Transistor, NPN, Video Out, Red |
| 5103 | F7510 | Transistor, NPN, Video Out, Green |
RESISTORS
| R5101 | 63-10840-88 | 4.7K Ohm, +5%, 3W Film | |
| 5102 | 63-7785 | 1K Ohm, | +10%, 1/2W Carbon |
| 5103 | 63-7785 | 1K Ohm, £10%, 1/2W Carbon | |
| R5104 | 63-10235-54 | 180 Ohm, +5%, 1/4W Film | |
| R5105 | 63-10235-48 | 100 Ohm, +5%, 1/4W Film | |
| 5106 | 63-7785 | 1K Ohm, #10%, 1/2W Carbon | |
| 5107 | 63-7785 | 1K Ohm, | +10%, 1/2W Carbon |
| 5108 | 63-7785, | 1K Ohm, | #10%, 1/2W Carbon |
| 5109 | 63-7785 | 1K Ohm, +10%, 1/2W Carbon | |
| R5110 | 63-7785, | 1K Ohmi, | +10%, 1/2W Carbon |
| RS111 | 63-7799 | 2.2K Ohm, +10%, 1/2W Carbon | |
| R5112 | 63-10840-88 | 4.7K | Ohm, +5%, 3W Carbon |
| 5113, | 63-10840-88 | 4.7K Ohm, +5%, 3W Carbon | |
| R114 | 63-10235-54 | 180 Ohm, +5%, 1/4W Film | |
| R5115 | 63-10235-54 | 180 Ohm, +5%, 1/4W Film |
MISCELLANEOUS
| 5A2 | 86-799 | Stake Connector 4/.156 |
| 6Cc2 | 86-799 | Stake Connector4/.156 |
| 5H3 | 86-799 | Stake Connector 2/.156 |
| 5X7 | 86-799 | Stake Connector 1/,312 |
‘A-10008 CRT Socket
6-22
9-155-10 (204-360) |
I | !
I i | i
S111 | 5104 S103 i 4 Fee 220UH 32200H I I S13 RS112
| H | | | Q5103 #4. | fan | ! |
| Ls101 | w2t-1934 | a | Ee |
+ + 95102 ! + 121-1034 | 1 RED OUT I cs102
RS11S (80 | 174K
~ RSA S105 160 100 1/40 14H | i
| ! | | | | |
Nc pas
| ! | pyc sea | | |
| ' | io O 0 O oO: 8c2 | ' |
- «186 CENTERS —_______,
502 5A2
LGrouno RED NG Le | a GREEN
| BASE [aus ‘+140 VDC (GROUND
TOTAL RESISTORS ARE 1/2HATT UNLESS OTHERNISE
- SPECIFIED. M051-00087-A022 SCHEMATIC FOR |
| NOTES: cugee WITH CIRCUIT REFERENCE Festonrrons) | x | 3 |
A. PA = SEE PARTS LIST FOR APPLICABLE USAGE _ |
| B. ~e—e- = JUMPER WIRE USED 11 | RGE | t | ||
| Tl -® m @ = PROVISION ON PRINTED ED CIRCUIT BOARD. | | nen | eee | sR | TT |
ERT sek scant
| th | + | | ZF EN | IS9uF |
| DAG SIONAL | RADIO LURE. | | | to) |
| hh iba tee | i | ~ | a |
6-23
TO H.0.T. ASSY
~ ~ ~~ |
ht
a Lb ce | 530 PF 530 PF
CHICAGO, ILL.
CHICASL >
| a | . | _ | F-13473 | | |
| 7 | _- | a |
3v3 I | |
| Lo | 300MF | \ 700M | |
| MAIN MODULE | | 180KV | | | 180NV |
(SEE CHART) | |
| 0 | 303 | | | fe}— | a | _ |
| a | [eoooo; — | “4 | ] | | | are |
33 | [—
| 2 | ooo | ‘ | | | |
| alo | 303 | —— | |} | | |
| 9 | feooooa | Fel | —. | oo] |
| usr | tl | | | | | o.c To. |
2A3 . cS
| | | DAS | ry |
| LJ | / | poo |
| | | SWEEP MODULE | | |
| ° | (SEE CHART) | | |
E x oooo0d ooo 383 3R3 oo [aos ]
| bl | 18 | fas | — | — |
| eo? | ¢ | al |
+ IMPORTANT SAFETY NUTICE WHEN SERVICING TMs CHAGEIS, UNDER 3K SUN BF MCCIFIEC OR ALTEREC I THOUT
| a | 285 | 3F3 | 318 | 3R8 | 20] [3 | BERISSION FROM THE ZENITH RACIC, COR | ||
| arias | : | . | ||||||
| oo00 | oooo00 | oaa | 0 | 5 | o | o o a | i> * | PORCEL Chk. WITH TYPES TCENTICAL TC |
—F THETe uy" TEAL UCCAr TON. WIRING AN
| HV POWER | prcsatt | oes | ° |
| ~ | . | pouePLY | CarGuT ow |
ee eee Tepecia, 21RcUITS aR
| f | YOKE | (SEE CHART) | 1 VENT Ghe2K ANE PIRE HADRRO’ | THEY |
| i | m10 | ARE SHRCEL CN THE <cHEMATIC For EASY |
TRENTIFIERTICN, THE LETTER. x" INCLUDE
| AIR | ° | ’ IN THE ITEM NUMBER LESIGNATES: 3PE: |
I FAILEAEE “CMPUNENT:~ 1 THESE ARES: | WHICH ARE REGJTREG TL MRINTAIN SAFE PER-
| ' | 10 | | FCRMANEE, NO CEVIATIONG ARE ACCUMEL, | |
| TO DEGAUSSER | 4 | 3] | - |
AC SABE R/C ERE ORARNICE TMEROVEMENT BRANGES INTC THe GET -TC NUT Ge AVEC | UNTIL THE NEW SERVI LITERAT: the
| _ | - | 7 | 37 | ao | PRINTEL, |
| — | | | | | 353 | [a] |
Ll PCB
| eee | 8 | * ASSEMBLY |
{|} WIOTH STEP
| eo | =~ | _| | (SEE CHART) |
| VIDEO OUT (SEE CHART) 1 SH3
| ee] | [elo | of | M05 1-00087-A025 |
7 Q a OR if TOD fil TOR SL DAG Ser Tk. 1SSJE ZEN LS | oT “7 yr RAL Le mei | feta 6-25