CATHODE RAY TOMES

Warlords Upright TM-175 1st Printing

Warlords (Atari, 1980) · Technical Manual · 56 pages · 35 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

GAME SERIAL # (IDENTIFICATION TAG

MONITOR

REGULATOR/AUDIO II PCB

GAME PCB

GAME SERIAL NUMBER LOCATION

Your game's serial number is stamped on a plate on the outside of the game. The same number is also stamped on the chassis of the monitor, Regula: tor/Audio Il PCB, and the Warlords™ Game PCB. Please mention this number whenever calling your distributor for service.

Page 3

Operation, Maintenance j HA and Service Manual Y F; 4 Complete with Illustrated Parts Lists \

5 i}

ATARI + Ware: communications Company

Page 4

Copyright © 1981 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a Phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher,

Published by: ATARI INC. 1265 Borregas Avenue P.O. Box 427 Sunnyvale, California 94086

Lithographed in the USA. 4K

Page 5

Warlords”

Notice Regarding Non-Atari Parts

WARNING

Use of non-Atari parts or modifications of your Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

Atari, Inc.’s warranty (printed on the inside back cover of this manual) may be voided, if you do any of the following:

1.) you substitute non-Atari parts in your coin-operated game, or

2.) you modify or alter any circuits in your Atari game by using kits or parts not supplied by Atari.

Not only may the use of any non-Atari parts void your warranty, but any such alteration may also adversely affect the safety of your game, and may cause injury to you and your players.

Page 6

Table of Contents

1 Location Setup A. New Features. . B. Game Inspection C. Game Installation. .

  • Voltage Selection
  • Interlock and Power On/Off Switche: D. Self-Test Procedure................ E. Option Switch Settings .
  • Bonus Play Feature .
  • Coin Mechanism Multipliers . .
  • Examples of Game Price Settings a F. GamePlay ................... -. 12 . Attract Mode ... : . . Ready-to-Play Mode ....... 00.00 cece e cece ence e ene ee eee e nes 13 . PlayMode .......... . High Score Initial Mode 2.00.0... ec teens 13 OCOOWDMDARWOWWH

Pons

2 Maintenance and Repair A. Cleaning ....... 0.062 cece eee eee ete B. Fuse Replacement..... C. Opening the Control Panel .

  • LED Switch Replacement. .
  • Potentiometer Replacement D. Monitor Removal ......... E. Printed-Circuit Board Removal
  • Game PCB Removal .........
  • Regulator/Audio Il! PCB Removal ...... F. Fluorescent Light and Speaker Replacement a G. Game Operation. .... 2.0.6.

3 Illustrated Parts Lists \llustrations and parts lists begin on page ............-. essere eee 26

Page 7

» List of Illustrations

Figure 1 Overview of Game 2 Figure 2 Installation Requirements . . 3 Figure 3 Voltage Plug Selection. ... 2.2... eee e eee eee 4 Figure 4 Interlock and Power On/Off Switches ................00.. 000000 5

Figure 5 Location of Self-Test Switch, Volume Control and Option Switches... 6 Figure 6 Self-Test Procedure 7 Figure 7 Game Option Settings ... 8 Figure 8 Game Price Settings. .... 10

Figure 9 Coin Counter Option Settings Figure 10 Opening the Control! Panel and Replacing Player Controls .. Figure 11. Monitor Removal Figure 12 — Printed-Circuit Board Removal ...

Figure 13 Fluorescent Tube Replacement . . . 20 Figure 14 ~— Power Distribution . 22 Figure 15 Signal Distribution .... - 23 ’ Ilustrated Parts Lis Figure 16 Cabinet-Mounted Assemblies ...... +26 | Figure 17 Regulator/Audio Il PCB Assembly . . 28 Figure 18 Warlords™ Game PCB Assembly . . 30 Figure 19 Control Panel Assembly .. 33

Figure 20 Power Supply Assembly for Raster-Scan Games . . 2. 34 Figure 21 Fluorescent Light and Speaker Assembly. . . 36 Figure 22 American-Made Coin Door 22. 38 Figure 23 British-Made Coin Door ........... 2.622 e cece eee 42

Page 8

Warlords™/Cocktail

NOTE If reading through this manual does not lead to solving a certain maintenance problem, call Tele-Help® at the Atari Customer Service office in your geographical area, as shown below.

WEST and CENTRAL U.S.A. Parts for all Atari customers in the U.S.A. Game sales and service

Atari, Inc. California Customer Service Office 1105 N. Fair Oaks Avenue P.O. Box 427, Sunnyvale, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Pacific Time) From California, Alaska or Hawaii (408) 745-2900 s From anywhere else in this area toll-free (800) 538-1611

EAST U.S.A. Game sales and service only

Atari, Inc. New Jersey Customer Service Office Cottontail Lane, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) age From New Jersey (201) 469-5993 From anywhere else in this area © toll-free (800) 526-3849

EUROPE Parts for all Atari customers in Western Europe. Game sales and service

Atari Ireland Limited European Customer Service Office TIPPERARY TOWN, Tipperary Town, Ireland IRELAND Telex 28165 (Monday-Friday, 9:00-6:00 pm GMT)

@ 06252155

vi

Page 9

A. New Features

‘e*. The Warlords™ game has one new part. Even if you are familiar with Atari games, you should note this important difference. The new part is: @ Deep-Well Coin Box. This new coin box conservatively holds $600 in U.S. quarters. Pleasenote that $500 in quarters weighs over 11 kg (25 Ibs.), and $600 in quarters weighs 12% to 13% kg (28-30 Ibs.).

This new part, as well as all other major parts in the game, are illustrated in Figure 1. Throughout this manual, wherever this new part is mentioned, you will see this eae ’-.\)

‘Location Setup

Page 10

ATTRACTION PANEL

MONITOR SHIELD

ACCESS PANEL

CONTROL PANEL MONITOR

COIN DOOR

GAME PCB

REGULATOR! AUDIO II PCB

POWER SUPPLY POWER ON/OFF SWITCH

Figure 1 Overview of Game

Page 11
WARNING: SHOCK HAZARD Connect this game only to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electric shock if this game is not properly grounded!

B. Game Inspection

This new game is ready to play upon removal from the shipping carton. However, your careful inspection is needed to supply the final touch of quality control. Please follow these steps to help us insure that your new game was delivered to you in good condition.

NOTE Do not plug the game in yet!
  • Examine the exterior of the game cabinet for dents, chips, or broken parts.
  • Unlock and open the access panel of the cabinet and inspect the interior of the game as follows: @ Check that all plug-in connectors (on the game harness) are firmly seated. Replug any connectors found unplugged. DON’T FORCE CONNECTORS TOGETHER. The connectors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB and will void your warranty. @ Check that all plug-in integrated circuits on the game PCB are firmly seated in their sockets.
WARNING To avoid possible unpleasant electrical shock, do not touch internal parts of the monitor with your hands or metal objects held in your hands!

@ Note the location of the game's serial number—it is printed on the special label on the outside of the game cabinet. Verify that the serial numbers also stamped on the Warlords™ Game PCB, Regulator/Audio II PCB, and monitor are ail identical. A drawing of the serial number components is on the inside front cover of this manual. Please mention this number whenever you call your distributor for service. @ Check all major subassemblies such as the power supply, control panel and monitor for secure mounting.

Cc. Game Installation

Figure 2 Installation Requirements

Power 125 watts Temperature 0 to 38°C (32 to 100°F) Humidity Not over 95% relative Space Required 64 x 81% cm (25% x 32 in.) Game Height 182% cm (71% in.)

  • Voltage Selection The power supply in this game has four colored voltage selection plugs and operates on the line voltage of almost any country in the world.

Before plugging in your game, check your power supply. Make sure that the voltage selection plug on the power supply is correct for your location’s line voltage. Check the wire color on the plug and see if it is correct per Figure 3.

Page 12

voutace & SELECTION

Line Voltage Range Voltage Selection Plug Color

90-110 VAC (100) Violet 105-135 VAC (120) Yeliow 200-240 VAC (220) Blue 220-260 VAC (240) Brown

WARNING

Fuse cover must be in place during game operation.

Figure 3 Voltage Plug Selection

  • Interlock and Power On/Off Switches To minimize the hazard of electrical shock while working on the inside of the game cabinet, two interlock switches have been installed (see Figure 4). One is located behind the access panel and one is behind the coin door. These switches remove all AC line power from the game circuitry when a door is opened. Check for proper operation of the interlock switches by performing the following steps:

@ Be sure the coin door and rear access panel are closed. Plug the AC line power cord into an AC outlet. Set the power on/off switch to the ‘“‘on” position. Within 30 seconds the monitor should display a picture. Slowly open the rear access panel. The monitor picture should disappear when the door is opened approximately 2.5 cm (1 inch). Close and lock this panel and repeat this step with the coin door. If the results of the preceding step are satisfactory, the interlock switches are operating properly. If the monitor doesn't go off as described, check to see if the corresponding interlock switch is broken from its mounting or stuck in the “‘on” position.

Page 13

SAFETY INTERLOCK SWITCH

POWER ON/OFF SWITCH

Figure 4 Interlock and Power On/Off Switches

Page 14

D. Self-Test 6 Procedure

Part of the self-test procedure includes a display of the operator-selectable game options. Therefore, This game will test itself and provide data to we suggest you run the self-test procedure anytime demonstrate that the game's circuitry and controls you need to change the game’s options. are operating properly. The data is provided on the monitor, the light-emitting-diode switches, and the To run the self-test, follow the instructions outgame speaker, no additional equipment is neces- lined in Figure 6. sary.

OPERATOR OPTION SWITCHES

===" ON UTP t VOLUME INCREASE: SELF-TEST | TURN CLOCKWISE SWITCH |

WS) Hy SELF-TEST

SWITCH (EURO- PEAN GAMES) VOLUME CONTROL

Figure 5 Location of Self-Test Switch, @

Volume Control and Option Switches

Page 15

Instruction Figure 6 Self-Test Procedure

Results if Test Passes Results if Test Fails

  • Unlock and open the coin door. Set self-test switch to ‘on position (see Figure 5).
  • Turn each shield control knob slowly back and forth and observe the monitor.
  • Activate the following switches: slam, coin mechanism, and two LED switches.
  • When satisfied with test, set selftest switch to off position. Close and lock the coin door. The monitor displays the picture below. You may hear a ticking sound. This is normal.

A fireball will move smoothly on a diagonal across the screen. Ignore any “wraparound” that the fireball does on the screen.

You will hear a high tone; also, one of the characters in the 4th row of Os and 1s on the screen will change to a 1 (on). Simultaneously pressing more and more switches will progressively lower the tone. Tone disappears when all switches are released.

All coin acceptor and LED lamps are lit. RAM FAILURE is indicated by the message BAD RAM.

ROM/PROM FAILURE is indicated by the message BAD ROM.

A fireball will jump erratically or not move at all, indicating a bad potentiometer or loose harness wires.

A low tone produced while you are not pressing any switches indicates at least two switches arg shorted together.

No sound at all indicates bad sound circuitry, loose speaker wires, bad switch circuitry or volume control turned all the way down.

Either some or all lamps are dark (burned out).

SWITCH TOGGLE 8 RK Cree On oorr OD one FX BORG gore OO Core Boe eran oO

L,C & RCOIN SWITCHES. SLAM SWITCH SWITCH TOGGLE 1

SWITCH AT J2

SWITCH AT M2

Ignore this row

2 POWER-STONE (LED) SWITCHES

Page 16

E. Option Switch Settings

  • Bonus Play Feature Warlords™ offers a bonus play for certain combinations of coins inserted. This bonus feature is operator-selectable, meaning you may choose to offer it or not.

With your game set at 50¢ per play, players who deposit four successive quarters or a $1.00 coin, then press the start button, can receive a bonus play. Therefore, players can receive 3 plays for $1.00.

This bonus feature encourages players to insert more money than just the minimum 50¢ required for one game. Various other bonuses are also available (see Figure 8).

Figure 7 Game Option Settings

To change toggle positions on the switch assemblies, you need not remove the game PCB. The switches, usually colored blue, are easily accessible when the Warlords™ Game PCB is mounted in place. When changing the options, verify proper results on the monitor display by performing the self-test. Note that changing an option on any of the following eight toggles will cause an immediate change on the monitor screen during the self-test.

Toggle Settings of 8-Toggle Switch on Warlords PCB (at J2—CENTER LEFT switch when PCB is in game)

87654321Option
OnOnEnglish language$
OnOffFrench language

off On Spanish language

off off German language

3g2OnMusic ends each game.$
333OffMusic at end of game only for a new high score
3535(1- and 2-player games onl
22s(playeriy).
OnOn1- to 2-player game costs 1 credit.
OnOff1-player game costs 1 credit; 2-player game costs 2

credits. $

oftOff1 to 2-player game costs 2 credits.
OffOnNot Used.

$ Manufacturer's suggested settings For pricing for “credits”, see Figure 9.

Page 17
  • Coin Mechanism Multipliers Since early in 1980, Atari has made available its new coin door which has either two or three mechanisms. All recent Atari game PCBs identify the different mechanisms in a certain pattern.

The right coin mechs are all the same to the game's logic, regardless of whether you have two or three mechs in your door. In addition, the logic sees the left mech in a 2-mech door and the center mech in a 3-mech door as the same. Refer to the diagram below.

[2se [st 2s¢} |[j2se| [$1 This pattern is important for you to know, so you can correctly set the “multipliers” for each mech. The multipliers determine how much each mechanism will be worth to the game's logic.

The basic unit of measurement is 25¢, which equals a multiplier of x1. Therefore, if you have a 25%/25¢/$1 coin door, you will probably want to set the center and right option-switch multipliers at x 1x 4. (The left mech in a 3-mech door always has a value of x 1—you cannot change its value.)

You can set these multipliers with toggles 3 thru5 on the Warlords™ PCB switch assembly at location M2. For exact settings of these toggles, refer to Figure 8.

  • Examples of Game

Price Settings

Figure 8 explains the options, giving twelve examples of the most common USS. situations. The toggles mentioned below are all in the switch at location M2; they only relate to game price, coin mechanism multipliers, and bonus plays. You should set the toggles relating to other functions as you see fit, although Figures 7, 8, and 9 provide “$" symbols indicating Atari’s recommendations.

Page 18

Figure 8 Game Price Settings The white block below contains Atari’s suggested settings. All numbers 1 thru 8 are toggle settings on the 8-toggle switch at location M2, on the Warlords™ game PCB (the UPPER LEFT switch assembly).

50¢ PER CREDIT:

Bonus No bonus

Straight 25¢ Door

25¢/$1.00 Door or 25¢/25¢/$1.00 Door

25¢ PER CREDIT:

Bonus Bonus No bonus $.50 = 3 credits $1.00 = 5 credits

Straight 25¢ Door =

On

25¢/$1.00 Door or 250/257/$1.00 Door

Circled numbers refer to coin-door labels you should use with each situation (labels are illustrated on the following page).

Page 19

Figure 8 Game Price Settings, continued For your information, we have defined below the switch set- need to temporarily set the Warlords™ game on free play, or if you tings for those options relating to game price, coin mechanism —_-have German coin mechanisms in your door. multipliers, and bonus play. This information is useful in case you

Toggle Settings of 8-Toggle Switch on Warlords PCB (at M@2@—UPPER LEFT switch when PCB is in game)

87654321Option
OnOnFree play
Onoft1 coin* for 2 credits
offOn1 coin* for 1 credit$
offoft2 coins* for 1 credit
OnOnRight coin mech x
OnoffRight coin mech x

off On Right coin mech x

offofRight coin mech x

Oana

OnLeft coinmech x 1$Both these settings affect
OffLeft coin mech x 2the center mech in a 3-mech

door)

OnOnOnNo bonus coins
OnOnoffFor every 2 coins* inserted, game logic adds 1 more

coin*

On oft On For every 4 coins” inserted, game logic adds 1 more

coin*

OnoffoffFor every 4 coins” inserted, game logic adds 2 more

coins* $

offOnOnFor every 5 coins” inserted, game logic adds 1 more

coin

*In the U.S., a coin is defined as 25¢. In Germany a coin is 1 DM.

$ Manufacturer's suggested settings To receive any bonus “coins” from the game logic (as listed in the

last four settings above), players must insert all coins before "Nag @ @ 2coins

pressing any start button. . A @@® 3 coins 000 @ 4 coins

oe © @@ 2 coins =1 play A, @@ 2 coins =1 play A @ $1 coin =3 plays (Susan B. Anthony coin)

O71 @ 1 coin = 1 play C2)

AL @ 1 coin = 1 play mai 2 play minimum

(2 coins = 2 plays)

ATARI

AO @ @ 2 coins = 1 play (For operator use—write in e@ e @ @ 4 coins = 3 plays tant marker.)

the appropriate phrase. Use 2 permanent-ink water-resis-

ah

Page 20

Figure 9 Coin Counter Option Settings

[These toggles determine which coin mechanisms activate which counters]

Toggle Settings of 4-Toggle 7 Switch on Game PCB (L9) Two coin acceptors 4 3 2 41 in the coin door: Two coin acceptors and a pushbutton utility coin switch in the game: Three coin acceptors in the coin door:

OnOnBoth acceptors activate all coin

counters simultaneously.

OffOnBoth acceptors activate 2 count-

ers separately. 3 3

>>OnOffBoth acceptors activate all coin

s counters simultaneously.

OffOffBoth acceptors activate 2 count-

ers separately. $ Do not use this setting.

Do not use this setting.

Utility coin switch will not activate a coin counter, if you do not hook up it up. Both acceptors activate all coin counters simultaneously.

Utility coin switch will not activate a coin counter, if you do not hook it up. Left and right acceptors activate 2 coin counters separately. All 3 are same denomination and they activate all coin counters simultaneously.

Left and center acceptor activate ‘one coin counter; right acceptor activates another coin counter.

Left acceptor activates one coin counter; center and right acceptor activate another coin counter. Not for any currently designed 3-mech coin door.

Left, center and right acceptors activate 3 coin counters separatey. $

$ Manufacturer's suggested settings

F. Game Play

Atari's Warlords™ is a one- or two-player game

  • Attract Mode with a black-and-white raster-scan monitor. The game depicts a third-person view of four castles. The knights and kings use shields to defend their castle walls from the fireballs that ricochet around the playfield. The attract mode begins when power is applied to the game, after a play or high score initial mode, or after self-test. This mode is continuous and is only interrupted when a game is paid for and accepted or when you enter self-test. Players can capture and catapult the fireballs at opposing castles, using their shield control and ‘power stone” pushbutton. When a fireball hits a castle wail, it destroys one or more bricks, depending on its speed. In this mode, the monitor displays a simulated game of two computer-controlled black knights. A fireball bounces across the playfield, knocking several bricks out of castle walls. A position not paid for is played by the computer, with a black knight displayed in the appropriate castle. (The upper two castles always have black knights in them.) The computer-controlled knights catapult fireballs at the players with increasing accuracy, to provide challenge.

The game has five possible modes of operation: attract, ready-to-play, play, high score initial, and self-test. Self-test is a special mode for checking the game switches, potentiometers, and computer functions. You may enter this mode at any time. When entered, all game credits are cancelled. If you select one of the three coined-play settings, the screen shows GAME OVER/INSERT COINS, followed by various messages regarding number of coins required for multi-player games. If you set the appropriate option switches for free play, the game displays the message PRESS PLAYER START.

Invisible shields move around to protect their respective castle walls. This is why the fireball appears to be deflected from something near the middle of the playfield.

Page 21
  • Ready-to-Play Mode This mode begins when sufficient coins have been accepted for at least a one-player game. It ends when either player presses a start pushbutton and the subsequent countdown has ended. The countdown lasts about 10 seconds (counting from 9 to 0) and allows another player to insert coins and join the first player.
  • Play Mode The play mode begins when either start button is pressed and the countdown has ended. The mode ends when the last player's castle (containing a crown) has been penetrated by a fireball. At this point a white cloud envelopes the crown, and the latter disappears.

During the countdown a dragon flies back and forth across the screen with a fireball in its mouth. At the end of the countdown, a position activated by a start button has its black knight changed to a king’s crown. A position not activated remains as a knight and is controlled by the computer. The dragon then spits the fireball from its mouth toward a player's castle.

The objective is to destroy the three other castles, while protecting one’s own castle with the moving shield (potentiometer). The LED pushbuttons have dual functions: in the ready-to-play mode they work as start switches, and during game play they become “power stones” to allow players to capture and catapult fireballs at opponents.

The spinning fireballs released from a shield have more destructive force on a castle wall than a fireball simply deflected from another wail or the sides of the playfield. However, players will soon find out that they cannot hold onto a fireball for long, since it slowly destroys their own castle walls adjacent to the fireball.

Additional fireballs appear at predetermined intervals or when a castle is destroyed, whichever comes first. A maximum of four fireballs simultaneously appears on the screen.

In one- and two-player games, the players’ crowns will be accompanied by a zero, to begin scoring. The point-scoring system is printed on each control panel (the black knights do not earn points).

If the black knight has the surviving castle, the game ends. However, if a player (king) has the surviving castle, that player receives bonus points, all castles are rebuilt, and the game continues with a new battle at a higher “‘level.”

The subsequent levels begin, as mentioned before, with the fireball thrown out by the dragon. In the higher levels black knights play more accurately and faster.

If players abuse the game and activate the slam switch, the computer produces an oscillating highpitched sound as a warning signal. However, game play is not interrupted.

  • High Score Initial Mode If one or more players have achieved the Highest score currently in the memory, they can enter their initials. Turning the shield-contro! knob will change the letters, and pressing the start button will enter the selected initial. Up to three letters will be displayed next to the individual or team high score during the attract mode.
Page 22

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 23

Maintenance

» and Repair All games require certain maintenance to keep them in good working order. Clean, properly maintained games will attract players and earn more profits.

The most important maintenance item is running the self-test every time you collect money from the coin box. Just looking at a game will not tell you if light-emitting-diode switches or potentiometers are broken, or if LEDs have burned out. The self-test will inform you of any of these possible problems.

Second, you should regularly clean the outside of the game and the coin mechanisms.

Page 24

A. Cleaning

The exterior of the game cabinet and the metal and acrylic surfaces may be cleaned with any nonabrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor. Do not dry-wipe any of the acrylic panels, because any dust can scratch the surface and result in fogging the plastic.

B. Fuse Keplacement

This game contains six fuses—all on the power supply assembly (not including the monitor fuses). Replace fuses only with the same type as listed in Figure 20 of this manual. See the monitor manual, TM-125, for the monitor fuse data.

C. Opening the Control Panel

Prior to replacing any player control on the control panel, unplug the game. Then open the coin door.

Reach through the opening and remove both sets of carriage bolts, wing nuts, split lock washers, and large flat washers, located on the underside of the control panel (see Figure 10).

Lift up on the control panel and tilt it towards you. Be sure that the acrylic monitor shield does not fall on you. The top edge of the control panel acts as a retainer strip for the shield: once the control panel is opened, the shield is free and could slide out under its own power.

  • LED Switch Replacement The light-emitting diode (LED) switches on the control panel have a very low failure rate. In case a switch should ever be suspect, first test it per the description that follows. To replace the switch, refer to Figure 10.

@ Remove the wires from the suspected switch. @ Set multimeter to ohms scale. Set ohms scale to Rx 1, then zero the meter. @ Connect multimeter leads to appropriate LED switch contacts (see Figure 10 for designation of switch contacts and meter lead placement). @ Check contacts (push and release the switch button) for closed and open continuity. @ If the contacts do not operate sharply or always remain closed or open, then replace the LED switch as outlined in the figure.

  • Potentiometer Replacement Remove the wires from the faulty potentiometer. Using a 5/64-inch Allen wrench, loosen both set screws on the side of the shield control knob; remove this knob. Next remove the flat hex nut on the outside of the panel with a wrench. Then remove the internal-tooth lock washer.

Replace the potentiometer with a new one, making sure the hex nut and knob are tightened securely. Then reconnect the three harness wires.

Page 25

™ Warlords

NORMALLY CLOSED (N.C) CONTACT

LE NORMALLY OPEN

(N.O.) CONTACT

LIGHT-EMITTING-DIODE COMMON / ee (LE.D) CONTACTS

+ RED WIRE

To remove LED switch:

© Remove all wires from the faulty switch. @ Turn the switch counterclockwise while holding the black cone-shaped nut on the outside of the control panel. © Install a new switch using the reverse procedure. @ Reconnect the harness wires.

Figure 10 Opening the Control Panel and Replacing Player Controls

Page 26

e If you should need to remove the monitor, follow D. Monitor Kemoval steps 1 thru 4 that follow. Refer also to Figure 11. 6

  • Unplug the game from its wall outlet! Open the rear access panel. Reach in the opening and unplug the 12-pin harness connector at the bottom (rear) of the monitor chassis.
  • Unplug the 5-pin harness connector located at the center left side of the access panel opening.
  • Remove the two screws that hold rear of the monitor frame to the cabinet walls.
  • Locate the two black “L” brackets that hold the rear of the monitor to the cabinet walls. Remove the four screws that secure these brackets to the cabinet.
  • Slightly lift up the monitor chassis, and slide it out the rear of the game. You might have to slightly bend the bottom rear flap of the large cardboard bezel.
WARNING Shock Hazard High voltages may exist in any television or monitor, even with power disconnected. Use extreme caution and do not touch electrical parts of the yoke area with your hands or with metal objects in your hands! Implosion Hazard If you drop the monitor and the picture tube breaks, it will implode! Shattered glass and the yoke can fly 6 feet or more from the implosion. Use care when replacing any monitor.

Disassemble in the order indicated. (Circled numbers match the steps above.)

Figure 11 Monitor Removal

Page 27

REGULATOR AUDIO I! PCB

Figure 12 Printed-Circuit Board Removal

E. Printed-Circuit Board Kemoval

You may wish to remove the game printed-circuit board (PCB) or the Regulator/Audio || PCB for service or inspection. To do this, refer to Figure 12 and proceed as follows:

  • Game PCB Removal @ Open the rear access panel. @ Remove the two beaded nylon tie wraps from the PCB’s edge connector. Remove the 44-pin edge connector from the right side of PCB. @ Locate the Phillips-head screw that extends through the PCB and into the wood block (at the right side of the board). Remove and save this screw as well as the fiber washer. @ Remove the PCB from the cabinet by carefully sliding it straight out of the plastic PCB retainer. Be careful not to twist the board, as this may loosen connections or components. Replace or repair as required. GAME PCB

@ After servicing it, reinstall the PCB, making sure

y that the 44-pin edge connector is properly plugged in. Note that the connector is keyed to fit on only one way, so if it doesn’t slip on easily, don't force it! A reversed connector will probably damage your game and will void the warranty. Check that the operation of the game is correct by performing the self-test. This is especially important with any game when you replace a PCB.

Regulator/Audio Il PCB Removal Unlock and open the access panel. Remove the five plug-in connectors on the Regulator/Audio I! PCB. Note that all of these connectors are keyed for proper orientation. Locate the two Phillips-head screws that extend through the PCB and into the wood behind the PCB. Remove and save these two screws and the two fiber washers. Remove the PCB from the interior wall of the cabinet.

Page 28

Figure 13 Fluorescent Tube Replacement

F. Fluorescent Light and Speaker Keplacement

WARNING If you drop a fluorescent tube and it breaks, it will implode! Shattered glass can fly 6 feet or more from the implosion. Use care when replacing any fluorescent tube. Avoid looking at the blacklight when it is on. It may damage your eyes.

To replace the fluorescent white- or blacklight tube behind the front graphics attraction panel, follow this procedure (see Figure 13):

  • Remove the three Allen-head screws and lock washers at the top of the game (they secure the black metal retainer for the attraction panel). Lift the attraction panel up and out of its lower retainer. . If you need to replace the blacklight tube, remove the two Phillips screws that secure the light board to the cabinet, and slide out the whole assembly. The harness has plenty of length, so you can pull the assembly about two feet out of the game. . Remove the two Y-shaped connectors from the ends of the fluorescent tube: you may find it helpful to use a flat-head screwdriver. Now carefully remove the tube from its clamps by pulling it towards you. . Replace with a new tube. Do not snap the tube in vigorously—you may break it, causing an implosion! . Reconnect the Y-shaped connectors. Reinstall the fluorescent light assembly with the two screws (if you removed it). Replace the attraction panel on the front of the game. When tightening the Allen screws, be sure the top retainer strip is pushed tightly back against the attraction panel.
Page 29

G. Game Operation

With this manual you received two large sheets that contain the wiring and schematic diagrams for the Warlords™/upright game. Sheet 1, Side A, includes a “table of contents” that shows the arrangement of these diagrams. They include explanations of the functions of the circuits; the diagrams also define inputs and outputs.

Atari's Warlords™ is a microprocessor-controlled game. The microprocessor is contained on the game PCB. The game PCB receives switch inputs from the control panel and coin door. These inputs are processed by the game PCB and output to the monitor, Regulator/Audio || PCB, loudspeaker, coin counter, and control panel. The Regulator/Audio || PCB performs two functions: 1) it regulates the + 10.3 VDC from the power supply to +5 VDC, and 2) it amplifies the audio output from the game PCB. The +5 VDC from the Regulator/Audio Il PCB provides most logic power to the game PCB. The audio output from the Regulator/- Audio Il PCB directly drives the game speaker and is controlled by the volume control, mounted inside the coin door.

The power supply is the source of all voltages in the game. These voltages are protected by four fuses (F3 thru F5) on the power supply chassis. The primary winding of the power supply transformer is protected by the fuses F1 and F2 on the power supply chassis.

Figure 14 illustrates the distribution of power in this game. Figure 15 illustrates the distribution of signals.

Page 30

‘arlords™

> BLACK AND WHITE

FLUORESCENT LIGHTS ©

oT ' E>), SD |

S, b

MONITOR

-ONTROL ANEL

$ POWER INTERLOCK sg} ¢ a SWITCHES OIN DOOR _

[ GAME PCB ) S g ul _ ft POWER SUPPLY 2 <5 VOC = (OC g Pa 403 $ + AC POWER CORD

+EGULATOR/AUDIO II PCB

POWER ON/OFF SWITCH

Figure 14 Power Distribution

Page 31

) SPEAKER

CONTROL PANEL

COIN DOOR

POWERSTONE 1

Pa =

s

AUDION&2 SPEAKER 1&2 COIN COUNT ALL,C,

POWERSTONE 2

SELF-TEST

Figure 15 Signal Distribution MONITOR

VOLUME CONTROL

‘GAME PCB

,

REGULATOR! AUDIO I! PCB

Page 32

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 33

This chapter provides you with the necessary information for ordering replacement parts for your Warlords™ game. Please note that, for simplicity, common hardware has been deleted from most of these parts lists. This includes screws, nuts, washers, bolts, etc.

The parts lists are arranged in alphanumeric order. For example, all “A-” prefix numbers come first. Following this are numbers in sequenée evaluated up to the hyphen, namely 00- thru 99-, then 000598- thru approximately 190000-.

When ordering parts from your distributor, give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.

Illustrated

» Parts Lists

Page 34

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc. cama CA. This. Grawing is only conditionally issued, and neither recerpt nor Fluor. Lt. & Speaker Assy.— possession thereof confers or transfers any right in, oF I see Figure 21 cense to use, the subject matter of the drawing or any de- 036498-01 Sign oF technical information shown thereon, nor any right 7 iereproduce this drawing ot any part thereat. Except for

37,§ Hgtainenmanufacture by vendors of Atari, inc., and for manutacture

537207-01 mE Co, duce this drawing is granted or the Subject matter thereof SSS" unless by written agreement with or written permission

Attr. Panel)—036499-01from the corporation

(Mirror) 037210-03 984950 (Backgind. Bezel) 1364: 1 037210-04, -05 03720201 (Castie Inserts) (Cabinet Assy.)

(Mon. Shield) 02-305010 (T-Moiding)

A 002728-01 03721201

“1 Pai, Brkt)Control Panel Assy.—(Monitor Assy.)

see Figure 19 f A037282-01 92.040

(o0032. nsoor7 & Spkr. Harn.).(Monitor)

Control} a 228-0

y(Mon. "2" Brkt.)|!037210-02

sooo (Mon. Bezel) Ctl. Brkt) 036317-01 (Mirror Retainer) 036189.01 09647701 Sw. Assy.) (Rear Panel) 007882-02 74-2110 teri. Sw. Cvr,j (Lock) 037221-01 ; (Mon Gveray| )) 037229-01 y (Mon. Support Frame) 0357.45.02 036262-01 82-406

«Coin Box Brkt.)(Eyebolt)ae ea
aniaGon a037225-01i(PCB Tie Wrap)
(Deep WellCoinBox)(Mon. “L" Brkt)Kl©7507017
037210-01r(PCB Spacer)

(Coin Detictr.) A037232-01

00788202we(Main Harn.)

(interl. Sw. Cvr.) — 034536-03 ~ Vib

A036189-01°ilaetell d

(interl. Sw. Assy.) ‘Game PCB Assy.—

034536-02 (Vibra. Damper) NN A>—- X] see Figure 18

Reg./Audio It PCB— ‘see Figure 17 4 f SS

7 A034841-05,

nematics, Self-Test Label & Manuals—00999201A034863-05,
see parts list on following page(Oniott Sw. Cvr.)or A035989-05
7Power Supply Assy.—(Power Cord)

(On/Oft Sw. Plate) see Figure 20 78-3201 61-162A (Cabinet Leg) (On/Off Switch)

Figure 16 Cabinet-Mounted Assemblies A037201-xx D

Page 35

Figure 16 Cabinet-Mounted Assemblies, continued Parts List

Part No. Description A034841-05 U.S. Strain-Relief Power Cord A034863-05 German Strain-Reiief Power Cord SSS

A035943-01Deep-Well Coin Box Assembly(for ali the same coins)
A035943-02Deep-Well Coin Box Assembly(for two different coin denominations—has one separator)
A035943-03Deep-Well Coin Box Assembly(for three different coin denominations—has two separators)

A035989-05 Australian Strain-Relief Power Cord A036189-01 Interlock Switch/Bracket Assembly (modified for safety) A037202-01 Wood Cabinet Assembly (includes legs and PCB retainers) A037212-01 Monitor Assembly (includes frame, brackets, eyeboits and all common hardware) A037232-01 Main Harness Assembly A037282-01 Light and Speaker Harness Assembly (at upper rear of game) The following five items are the technical information supplements to this game: DP-175-01 Warlords™/Upright Schematic Drawings (Sheet 1) DP-175-02 Warlords/Upright Schematic Drawings (Sheet 2) ST-175 Label with Self-Test Procedure and Option Switch Settings TM-125 Technical Manual for 19- and 23-Inch Wells-Gardner Raster-Scan Monitors TM-175 Warlords/Upright Operation, Maintenance and Service Manual 02-305010 ¥Y-Inch Black Plastic T-Molding 19-9032 50-Ohm, 12¥2-Watt, Wirewound Rheostat (vo/ume control) 61-1624 DPST Power On/Off Toggle Switch 71-2110 Panel Cartridge Lock Mechanism (for rear access panel) 75-07017 Spacer for Mounting Printed-Circuit Boards

78-240125-Inch Beaded Nylon Tie-Wrap(for Game PCB edge connector)

78-3201 Cabinet-Leveling Leg 82-406 #1%-20 Machine-Thread Eyebolt, 2 inches long overall (for mounting monitor to frame) 92-040 Wells-Gardner 23-Inch Monochrome Raster-Scan Monitor 002728-01 Control Panel Mounting Bracket A 006450-01 On/Off Switch Mounting Plate 007882-02 Interlock Switch Cover 009992-01 On/Off Switch Cover 030168-01 Volume Control Mounting Bracket 034536-02 Ya-Inch-Thick Foam Vibration Damper (for Regulator/Audio |i PCB) 034536-03 1 1/8-Inch-Thick Foam Vibration Damper (for Game PCB) 035745-02 18-Inch Plastic PCB Retainer 035942-01 Deep-Well Coin Box Separator 036262-01 Coin Box Bracket 036317-01 Mirror Retainer 036477-01 Rear Access Panel (does not include lock) 036495-01 Speaker Grille 036498-01 Retainer for Attraction Panel 036499-01 Half-Silvered (Semi-Transparent) Mirror 036686-01 Sheet of Game Pricing Labels 037207-01¢ Attraction Panel with Graphics 03720801. > Monitor Shield with Graphics 037210-01 Cardboard Coin Deflector 037210-02 Cardboard Monitor Bezel 037210-03 Cardboard Background Bezel 037210-04 Cardboard Castle Insert 037210-05 Cardboard Castle Insert (If replacing these inserts, note that all castle doors should face the bridges) 037221-01 Monitor Overlay with Graphics

037225-01Monitor Support “L” Bracket(at rear two corners of chassis)
037228-01Monitor Support “Z” Bracket(at top two corners of screen)

037229-01 Steel Monitor Support Frame

Page 36

is only conditional . nor possession thereof conters or transters any

aw.

) o MOL U2 ire) i

= 0 sin Of) ER T Te Lo rope] fe 3 J OF 0 ans) or = o S 1 | | 8x2 282. c+ L

3 aah o 2 & yee 28a) (284) ala ‘ = mr mie + ad a |On on

: | ol +

Ee Sick erie 7905 7812

oO —R24,12,,7Wi—

TDAZ002A Toaz002 A TIP 32

Vew ci4 Re2tie0) com 220] R2! ci2

cOIRe Dell RD

+L Ps & Py 7 4 cs) En EY

fo} oF T =62| NSH) Qh S88 09s)

L ° a 2 ss 8 q ; iy ad Og ae BASS | MY s

2 go Po gy SOT ae Ss EJ ar seu na] = er] in T EXvarael IS] 7 ty ae 98 oe

eo D Figure 17 Regulator/Audio Il PCB Assembly A035435-02

Page 37

Figure 17 Regulator/Audio || PCB Assembly Parts List

Part No. Description (Reference Designations and Locations in Bold)

12-52P7 2.7 Ohm, +5%, 1W Resistor (R5) 16-54PO 4.Ohm, +5%, 5W Wirewound Resistor (R25) 19-100P1015 1. Ohm, +3%, 7W Wirewound Resistor (R24) 19-315102 4K Ohm Vertical PCB-Mounting Cermet Trimpot (R8) 24-250108 4000 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C13) 24-250477 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C1, 4, 12) 24-350226 22 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor (C24, 31) 24-350338 3300 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor (C9, 10, 18, 19) 24-500105 1 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C22, 23) 29-088 1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C3, 11, 20, 21) 31-1N4002 100V 1-Amp. Silicon Rectifier Type 1N4002 Diode (CRI, 4-8) 31-5401 100V 3-Amp. Silicon Rectifier Type 1N5401 Diode (CR 5-8) 33-TIP32 PNP Power Transistor, Type TIP32_ (Q2) 34-2N3055 NPN Silicon Transistor, Type 2N3055 (Q3) 37-LM305 5V Linear Voltage Regulator (Q1) 37-7812 +12V Voltage Regulator, Type 7812 (Q8)

37-7905 —5V Voltage Regulator, Type 7905 (Q9) 72-1608C #632 x ¥2-Inch Cross-Recessed Pan-Head Corrosion-Resistant Steel Machine Screw 75-F60405 #6-32 x Va-Inch Binder-Head Nylon Screw 75-99516 #6-32 Nut/Washer Assembly 78-16008. Thermally Conductive Compound (Q3) 78-16014 Thermally Conductive Silicon Insulator (Q2, 9) 79-58306 6-Position Connector Receptacle (J6, 9) , 79-58308 9-Position Connector Receptacle (J7) 79-58346 42-Position Connector Receptacle (J10) 79-58354 4-Position Connector Receptacle (J8) 020670-01 Test Point 034531-01 Heat Sink 100015-103 01 uf Ceramic-Disc 25V Radial-Lead Capacitor (C5, C14) 110000-010 1 Ohm, +5%, YW Resistor (R10, 19) 110000-100 10 Ohm, +5%, %W Resistor (R11, 20, 29, 30) 110000-101 100 Ohm, +5%, %W Resistor (R4, 12, 22) 410000-102 1K Ohm, +5%, YW Resistor (R27, 28) 110000-103 10K Ohm, +5%, YW Resistor (R13, 14) 110000-271 270 Ohm, +5%, v4W Resistor (R1) 110000-330 33 Ohm, +5%, 4W Resistor (R3) 110000-392 3.9K Ohm, +5%, v4W Resistor (R6) 110000-562 5.6K Ohm, +5%, YW Resistor (R32, 33) 110000-752 7.5K Ohm, +5%, ¥4W Resistor (R7) 110001-221 220 Ohm, +5%, Y2W Resistor (R9, 21) 116000-220 22 Ohm, +5%, 10W Wirewound Resistor (R31) 122002-102 001 uf Ceramic-Disc Minimum 25V Radial-Lead Capacitor (C2, 7, 16) 122004-224 .22 uf Ceramic-Disc 25V Capacitor (C6, 8, 15, 17) Type TDA2002A 8W Linear Audio Amplifier Integrated Circuit (Q5, 7) 137151-002

Page 38

7 E nas Pate § ry me) iis 1 agit 8 aig 9 : s a a Se Op J

& B 8 %aa SS tsi Ahold eet BE Jo
PaBBSWSSep el
ot |,2 ee
=riaarthPTT

Figure 18 Warlords™ Game PCB Assembly A036434-01 and -02 ®

Page 39

Figure 18 Warlords™ Game PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold) C012294-01 Audio VO N-Channel MOS/LS! Custom Chip (B3/4) 24-250107 400 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C29, 65) 28-101101 100 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C10) 28-101390, 39 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C68) 29-088 4 uf Ceramic-Disc 25V Radial-Lead Capacitor (C1-9, 11-28, 30-35, 37-43, 45-63, 66, 69) 31-1N100 400V Type-1N100 Switching Diode (CR2) 31-1N4001 75V Type-1N4001 Switching Diode (CR3, 5) 33-2N3906 Type-2N3906 PNP Switching and Amplifying Transistor (Q2, 8) 34-2N3904 Type-2N3904 NPN Silicon Transistor (Q1, 7, 9) 34-2N6044 Type-2N6044 Darlington NPN Transistor (Q3-5) 37-LM324 Type-LM324 Integrated Circuit (K9) 37-LM339 Type-LS339 Integrated Circuit (A5)

37-74LS00 Type-74LS00 Integrated Circuit (C4) 37-74LS04 Type-74LS04 Integrated Circuit (B6, J6) 37-74LS08 Type-74LS08 Integrated Circuit (C7) 37-74LS10 Type-74LS10 Integrated Circuit (C5, F3)

37-74LS32 Type-74LS32 Integrated Circuit (D4, E4, N9) 37-74LS42 Type-74LS42 Integrated Circuit (D3) 37-74LS74 Type-74LS74 Integrated Circuit (N4, K6, B7) 37-74LS83 Type-74LS83 Integrated Circuit (E5, F5) 37-74LS86 Type-74LS86 Integrated Circuit (D6) 37-74LS90 Type-74LS90 integrated Circuit (B5) , 37-74LS139 Type-74LS139 Integrated Circuit (C3) 37-74LS153 Type-74LS153 Integrated Circuit (H4, J4, K4, L4, M4, P7)

37-74LS157 Type-74LS157 integrated Circuit (E7, F7, H7, J7, C6) 37-74LS163A Type-74LS163A Integrated Circuit (M8, K7, P4, PS, P6, N5, N6) 37-74LS166 Type-74LS166 Integrated Circuit (D7, J8) 37-74LS174 Type-74LS174 Integrated Circuit (D5, D8)

37-74LS175 Type-74LS175 Integrated Circuit (L6) 37-74LS244 Type-74LS244 Integrated Circuit (B1, C1) 37-74LS245 Type-74LS245 Integrated Circuit (E2) 37-74LS257 Type-74LS257 Integrated Circuit (L2, K2, M3, M5, F8, H8)

37-74LS259 Type-74LS259 Integrated Circuit (P9) 37-74LS273 Type-74LS273 Integrated Circuit (F4, L7) 37-74LS373 Type-74LS373 Integrated Circuit (F2) 37-74S04 Type-74S04 Integrated Circuit (P3) 37-74874 Type-74S74 Integrated Circuit (N8) 38-MV5053 Type-MV5053 Light-Emitting Diode (CR1) 41-3003 100 uH, +5%, Hot-Molded Plastic Fixed R.F. Choke (L1) 62-001 SPST Momentary Pushbutton Switch (A7) 66-114P1T 4-Station, Single-Throw, Dual-Inline-Package Bit Switch (L9) 66-118P1T 8-Station, Single-Throw, Dual-Inline-Package Bit Switch (J2, M2) 79-42016 16-Contact Medium-Insertion-Force Integrated Circuit Socket (M6, N7) 79-42C24 24-Contact Medium-Insertion-Force Integrated Circuit Socket (K/L1, M1, 01, E/F1, H1, J/K1, FIH6, E6) [Continued on next page]

Page 40

Figure 18 Warlords™ Game PCB Assembly, continued Parts List

“art No. Description (Reference Designations and Locations in Bold) 79-42C40 40-Contact Medium-Insertion-Force Integrated Circuit Socket (B3/4, C2) 31-4302 Nylon Snap-In Fastener (Q3-5) 40-102 12.096 MHz, + .005%, Crystal (Y1) 40-6010 Microprocessor (C2) 10-7031 Random-Access Memory (H3, J3, K3, L3, H5, J5, K5, L5) 10-7033 Random-Access Memory (N1, P1) 10-7035, Random-Access Memory (L8, K8) 20670-01 Test Point 37153-01 Read-Only Memory (K/L1) 37154-01 Read-Only Memory (M1) 37155-01 Read-Only Memory (D1) 37156-01 Read-Only Memory (E/F1) 37157-01 Read-Only Memory (H1) 37158-01 Read-Only Memory (J/K1) 37159-01 Read-Only Memory—Graphics (E6, F/H6) 37161-01 Programmable Read-Only Memory (M6) 37235-01 Programmable Read-Only Memory (N7) 0015-103 .01 uf Ceramic-Disc 25V Radial-Lead Capacitor (C64) 0000-102 1K Ohm, +5%, YW Resistor (R20-23, 26-32, 37, 38, 42, 62-69, 74-81, 84, 85, 88, 90, 91) 10000-103 10K Ohm, +5%, “4W Resistor (R1-19, 24, 33, 44, 92, 93, 96) 10000-104 100K Ohm, +5%, %W Resistor (R50-53) 10000-105 1M Ohm, +5%, %4W Resistor (R34) 10000-122 1.2K Ohm, +5%, YW Resistor (R72) 10000-153 15K Ohm, +5%, %4W Resistor (R36) 10000-182 1.8K Ohm, +5%, YW Resistor (R71, 73) 10000-183 18K Ohm, +5%, %W Resistor (R87) 10000-221 220 Ohm, +5%, YW Resistor (R45-49, 94) 0000-471 470 Ohm, +5%, %4W Resistor (R54-61, 82, 83) 10000-472 4.7K Ohm, +5%, VW Resistor (R25) 10000-563 56K Ohm, +5%, %4W Resistor (R35) ‘ 10000-681 680 Ohm, +5%, %W Resistor (R95) 1008-105 1 uf, + 10%, Polyester 50V Radial-Lead Capacitor (C44) 22002-102 .001 uf Ceramic-Disc 25V Radial-Lead Capacitor (C36) 2004-224 .22 uf Ceramic-Disc 25V Radial-Lead Capacitor (C67) 31000-001 3.9V, + 10%, 0.4 W, Type-1N748 Zener Diode (CR4)

Page 41

62-039 (LED Switch) 75-07054 (Spacer) A037206-01 (Ctrl, Panel) 75-9910WO (Stamped Nut)

033127-01 (Sw. Bushing)

19-9022 (Potentiometer) 73-834 (Knob)

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING , NOTICE TO Att adsguvion eoacgen without ine spe cific written permission of Atari, Inc., Sunnyvale, CA. This Sti oy Soins nagar seo areseon Serra aa ee gee ater tne dawing any Wieneey Be sure ground wire is attached sign or technical information shown thereon, nor any right cent i re to reproduce this drawing or any part thereof, Except for to ter mounting bolt bef manufacture by vendors of Atari, Inc., and for manufacture locking up the control panel. under the corporation's written license, no right to reproduce this drawing is granted or the subject matter thereot Unless by written agreement with or written permission from the corporation’

Figure 19 Control Panel Assembly A037211-01 A

Parts List

Part No. Description

A037206-01 Control Panel with Graphics A037234-01 Control Harness Assembly 19-9022 5K Ohm, +20%, Linear Slip-Clutch Potentiometer 62-039 Momentary-Contact SPDT Light-Emitting-Diode Switch with Red Cap

73-834 Black Knob with Skirt 75-07054 Spacer for Light-Emitting-Diode Switch 75-9910W0 #15/32-32 Steel Stamped Nut 033127-01 Black Molded Switch Bushing

Page 42

79-4411006 (Fuse Post) 03454401

46-2017002 (Fuse)

03448201 (Chassis) 5 q A035674-01 - A034623-01 PI : iia (Volt. Plug Assy.) —| (Fuse Block) (Transt. & Harn.)

78-2708 (Bushing)

78-70501SC TOP VIEW ‘(Bracket 29-053 NOTICE TO ALL PERSONS RECEIVING THIS DRAWING (Elec. Cap) CONFIDENTIAL: Reproduction forbidden without the Specific written permission of Atari, Inc., Sunnyvale, CA This drawing rs only conditionally’ issued, and neither feceipt nor possession thereat confers or transfers any fightin, or eense to use, the subject matter of the draw ing of any design of technical information shown thereon, mor any right to reproduce this drawing oF any part thereot” Except for manufacture by vendors of Ata, Inc. and for manutactute under the. corporation's written itcense, no right to reproduce this drawing is granted or the subject matter theroot untess by written agreement 42-7140 \eith or written permission from the corporation, BOTTOM VIEW (Transt. only) ‘A006555-01 (Rect. PCB Assy.)

A034630-01 79-15021001 =| Filter Assy.) (Block)

A034629-01 {AC Harness Assy )

Figure 20 Power Supply Assembly for Raster-Scan Games A034560-02 D

Page 43

Figure 20 Power Supply Assembly for Raster-Scan Games Parts List

Part No. Description (Reference Designations in Bold) A006555-01 Rectifier Printed-Circuit Board Assembly A034623-01 Transformer and Harness Assembly (11) A034629-01 AC Harness Assembly A034630-01 RFI Filter Assembly (FL1) A035674-01 Voltage Plug Assembly (set of four plugs) 29-053, 26,000 uf 15V Electrolytic Capacitor (C1) 42-7140 Power Transformer Only (T1) 46-2013002 3-Amp. 250V 3AG Slow-Blow Glass Cartridge-Type Fuse (F4, F5, F6) 46-2017002 7-Amp. 250V 3AG Slow-Blow Glass Cartridge-Type Fuse (F1, F2, F3) 78-2708 Nylon Type 6/6 Hole Bushing with 5/8-Inch Inside Diameter x 55/64-Inch Outside Diameter x Ya-Inch Thick 78-70501SC_ 2-Inch-Diameter Capacitor Mounting Bracket 79-15021001 2-Circuit Single-Row Terminal Block 79-3206 5-Position 3AG Fuse Block with ¥4-Inch Quick-Disconnect Terminals 79-4411006 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post 034544-01 Fuse Block Cover

Page 44

99-11012 (1-In, Clamp) 70-306 (Black Tube) 79-561816P (Wire Nut) A005493-01 (Fi Lt. Harness) 48.009 (Bn. Spoke)

99-11003: (Starter) 99-11009 (Socket)

99-11008 (Transtormer)

A036691-01 (Fi. Lt. & Spkr. Harness)

70-304 (White Tube) NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereo! confers or transfers any right in, or license to use, the subject matter of the draw: ing or any design or technical information shown thereon, hor any right to reproduce this drawing or any part thereof Except for manufacture by vendors of Atari, Inc ‘and tor manulacture under the corporation's written iicense, no right to reproduce this drawing is granted or the subject matter thereof unless by written agreement with of weitten permission from the corporation 99-11011 (1 Ye-In. Clamp)

035835-01 or A036045-01 (Connector)

Figure 21 Fluorescent Light and Speaker Assembly A036610-01 B

Page 45

Figure 21 Fluorescent Light and Speaker Assembly, continued Parts List

Part No. Description A005493-01 Fluorescent Light Harness A036691-01 Fluorescent Light and Speaker Harness 48-009 8-Inch High-Fidelity Speaker 70-304 18-Inch 15-Watt Cool White Fluorescent Tube 70-306 18-Inch 15-Watt Blacklight Fluorescent Tube 79-561816P Spring Connector Wire Nut for 16- to 18-Guage Wires 99-11003 Fluorescent Lamp Starter 99-11008 Ballast Transformer

99-11009 Starter Socket 99-11011 1¥2-Inch Clamp (for white tube) 99-11012 1-Inch Clamp (for blacklight tube) 035835-01 Y-Lead Connector (part no. A036045-01 is an acceptable substitute)

Page 46

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the Specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither 99-10103 (Inner Pri wilevers) 75-9488 aceipt nor possession thereof conters or transters any ‘ght in, or license to use, the subject matter of the drawing

  • any design or technical information shown thereon, nor ny fight to reproduce this drawing ot any part thereo!. Ex. ‘ept for manutacture by vendors of Atari, Inc., and for 99-10096 (Fastener) 99-10095 (Self-Test Sw) 99-10052 (Lever) Z a ~ 99-1073 a (Decal) sanufacture under the corporation's written license, no eght to reproduce this drawing is granted or the subject “rater thereof unless by written agreement with or written seemission from the corporation. (Hex Nut)

99-10071 (Slam Sw) Ke 75-1408S ? : (Screw) , a)" Part of 99-1095

  • + | Sle x] B. 75-944S P SEN. i@ 99-10096 (Hex Nut) i ele e A (Fastener) 0 99-10063 i (Coin Chute) i 99-10097 «( 99-10040 (insul,) inlet Chute) } 9910101 (Coin Chute)

70-11-47 (Lamp), 99-1080 7 ‘Lamp Socket)

72-9406S (Screw) LY

San

99-10104 (Bar Retnr.)

99-10041 (Coin Counter)

99-10081 (Key Holder)

TAA2Kxxx (Coin Mech.) 75-9448 sre ay (Hex Nut) Or 10 72-9603S COIN RETURN 99-10065 (Coin Sw.) Fen CHUTE (Return Box) Ss soot: Se-1 0068 99-10075 thru : Ppaast (Coin Chute) '99-10078 SS (Sw. Wire) 31-1N4002—Part 99-10042 thru 29-100: of ee 99-10045 i (Coin Sw. Assy.) (Retainey —-78-1412S 99-1082 (Screw) (Cover)

Figure 22 American-Made Coin Door 71-1 0XXxx D

Page 47

99-10012 thru 99-10022, and 99-10107 (Button Assy )

99-10009 or 99-10010 (Door)

99-10094 (Insul.)

Part of 99-10074

99-10049 (Locking Arm)

75-5520B (Bolt)

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sun: nyvale, CA. This drawing 1s only conditionally Issued, and neither receipt nor possession thereof conters or transfers any right in, or license to use, the subject matter of the drawing or any design or technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc. and for manufacture under the corporation's writ ten license. no right to reproduce this drawing is Granted or the subject matter thereof uniess by Wratten agreement with or written permission from tne corporation.

71-102201 — U.S. 25¢/25¢ Coin Door 71-103202 — U.S. 25¢/25¢/25¢ Coin Door 71-103203 — U.S. 25¢/25¢/$1 Coin Door 71-102204 — German 2 DM/1 DM Coin Door 71-103205 — German 1/2/5 DM Coin Door 99-10055 thru 99-10059 (Button Cover)

9910070, 99-10083 99-1074 thru 99-10092, (Lock) and 99-10108 (Price Plate)

99-10062 (Button)

75-918S, (Hex Nut)

75-9158, (Hex Nut)

99-10051 (Frame)

71-102206 — German 1 DM/5 DM Coin Door 71-102207 — Belgian 5 FriS Fr Coin Door 71-102208 — Swiss 1 Frit Fr Coin Door 71-102209 — Japanese 100Y/100Y Coin Door 74-102210 — British 10 P10 P Coin Door 72-JA1405B (Screw) 99-10054 (Btn. Housing) 72-HA1404C (Screw)

99-10061 (Bezel)

99-10066 (Covert

99-10048 72-JA1405B {Harness—not (Screw) shown for clarity)

71-102211 — Australian 209/20¢ Coin Door 71-102212 — Italian 100 L/100 L Coin Door 71-102213 — U.S. 50°/50C (2 x 252) Coin Door 71-103214 — U.S. 50¢/50/50¢ Coin Door 71-103215 — U.S. 50°/50¢/$1 Coin Door

Figure 22 American-Made Coin Door 71-10xxxx D

Page 48

Figure 22 American-Made Coin Door, continued Parts List

Part No. Description

31-1N4002 100V Silicon Rectifier 1N4002 Diode 65-441C General-Usage Low-Force Miniature Switch 70-11-47 Miniature Bayonet-Base Incandescent Lamp, Type #47 71-4201ADU U.S. $1.00 Coin Mechanism 71-1201FCH Swiss 1 Fr Coin Mechanism

71-1201MG German 1 DM Coin Mechanism 71-1202MG German 2 DM Coin Mechanism 71-1205FB Belgian 5 Fr Coin Mechanism 71-1205MG German 5 DM Coin Mechanism /1-1210PE U.K. 10 P Coin Mechanism

71-1220CA Australian 20¢ Coin Mechanism 71-1225CU U.S. 25¢ Coin Mechanism 71-12100LI Italian 100 Lire Coin Mechanism 71-12100YJ Japanese Y100 Coin Mechanism 72-HA1404C #4 x Va-Inch Slotted Pan-Head Thread-Rolling Tri-Fluted “Taptite” Cadmium-Plated Screw 72-JA1405B. #4 x 5/16-Inch Slotted Pan-Head Thread-Rolling Tri-Fluted “Plastite” Black Screw 72-9406S #4-40 x 3/8-Inch Slotted Truss-Head Steel Machine Screw 72-9603S #6-32 x 3/16-Inch Slotted Truss-Head Steel Machine Screw 75-9158 #%-20 Standard-Pattern Cadmium-Plated Steel Hex Nut 75-918S #8-32 Standard-Pattern Cadmium-Plated Steel Hex Nut

75-944S #4-40 Polymer Self-Locking Steel Hex Nut 75-948S, #8-32 Polymer Self-Locking Steel Hex Nut 75-1408S #4-40 x V2-Inch Slotted Pan-Head Steel Machine Screw 75-1412S #4-40 x 34-Inch Slotted Pan-Head Steel Machine Screw 75-5520B #'%-20 x 1%-Inch Round-Head Square-Neck Steel Bolt with Black Finish 39-10008 Switch Wire Retainer 39-10009 2-Mech Coin Door Only 39-10010 3-Mech Coin Door Only 39-10012 U.S. 25¢ Coin Return Button Assembly 39-10013 U.S. $1.00 Coin Return Button Assembly 39-10014 German 1 DM Coin Return Button Assembly 39-10015 German 2 DM Coin Return Button Assembly 39-10016 German 5 DM Coin Return Button Assembly 39-10017 Belgian 5 Fr Coin Return Button Assembly 39-10018 Swiss 1 Fr Coin Return Button Assembly 39-10019 Japanese Y100 Coin Return Button Assembly 39-10020 U.K. 10 P Coin Return Button Assembly 39-10021 Australian 20¢ Coin Return Button Assembly 39-10022 Italian 100 Lire Coin Return Button Assembly 9399-10040 Coin Inlet Chute Assembly 99-10041 Coin Counter Assembly 9399-10042 Coin Switch Assembly for U.S. 25¢ and Belgian 5 Fr Coins (silver wire) 99-10043 Coin Switch Assembly for German 1 DM, Swiss 1 Fr, and Japanese Y100 Coins (black wire) 99-10044 Coin Switch Assembly for U.S. $1.00, German 2 DM, and Italian 100 Lire Coins (gold wire) 99-10045 Coin Switch Assembly for German 5 DM, U.K. 10 P, and Australian 20¢ Coins (green wire)

Page 49

Figure 22 American-Made Coin Door, continued Parts List

Part No. Description

99-10047 Lockout Coil Assembly 99-10048 Coin Door Harness Assembly 99-10049 Locking Arm Assembly 99-10051 Coin Door Frame 99-10052 Coin Return Lever 99-10054 Coin Button Housing 99-10055 Coin Return Button Cover for Japanese 100Y Coin 99-10056 Coin Return Button Cover for German 1 DM and Swiss 1 Fr Coins 99-10057 Coin Return Button Cover for U.S. 25¢ and Belgian 5 Fr Coins 99-10058 Coin Return Button Cover for U.S. $1.00, German 2 DM, and Italian 100 Lire Coins 99-10059 Coin Return Button Cover for German 5 DM, U.K. 10 P, and Australian 20¢ Coins 99-10061 Coin Return Bezel 99-10062 Coin Return Button 99-10063 Right Half of Coin Inlet Chute 99-10065 Coin Return Box 99-10066 Coin Return Cover 99-10068 Coin Chute 99-10070 US. 25¢ Price Plate 99-10071 Slam Switch Assembly 99-10073 Test Switch Decal 99-10074 Lock Assembly 99-10075 Black Switch Wire for German 1 DM, Swiss 1 Fr and Japanese 100Y Coins 99-10076 Silver Switch Wire for U.S. 25¢ and Belgian 5 Fr Coins 99-10077 Gold Switch Wire for U.S. $1.00, German 2 DM and Italian 100 Lire Coins 99-10078 Green Switch Wire for German 5 DM, U.K. 10 P and Australian 20¢ Coins 99-10080 Miniature Bayonet-Base Lamp Socket 99-10081 Wire Key Holder , 99-10082 Switch Cover 99-10083 U.S. $1.00 Price Plate 99-10084 German 1 DM Price Plate 99-10085 German 2 DM Price Plate 99-10086 German 5 OM Price Plate 99-10087 Belgian 5 Fr Price Plate 99-10088 Swiss 1 Fr Price Plate 99-10089 Japanese Y100 Price Plate 99-10090 U.K. 10 P Price Plate 99-10091 Australian 20¢ Price Plate 99-10092 Italian 100 Lire Price Plate 99-10094 Fish Paper Insulation 99-10095, Toggle Switch 99-10096 “U"-Type Fastener 99-10097 Fish Paper Insulation 99-10101 Left Half of Coin Inlet Chute 99-10102 Switch and Lockout Coil Bracket Sub-Assembly 99-10103, Inner Panel with Levers Sub-Assembly 99-10104 Anti-Penny-Flip Bar Retainer 99-10105 Anti-Penny-Flip Bar 99-10107 U.S. 50¢ Coin Return Button Assembly (for two quarters) 99-10108 U.S. 50¢ Price Plate (for two quarters)

Page 50

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproduction forbidden without the Specific written permission of Atari, Inc., Sunnyvale, CA This drawing is only conditionally issued, and neither receipt nor possession thereof confers or transfers any ight In, oF license to use, the subject matter of the draw: ng of any design or technical information shown thereon, not any right to reproduce this drawing or any part ereo!” Except for manufacture by vendors of Atari, Inc and for manufacture under the corporation's written cense. no right to reproduce this drawing is granted or ne subject matter thereot unless by written agreement auth or written permission from the corporation

99-15051 (Lamp Holder)

99-15026 99-15056 (Coin Inlet) (Screw for Bezel)

(Coin Intet)

PART OF 99-15041 99-15055 fy 99-15041 (Lockout Coil) 99-15053 (Lockt Gon Spring) Reing Screw) or

9915027 (Coin Ret, Box)

99-15037 > (Sw. Adjuster)

99-15029 (Bracket)

(Switch) LL 99-15001 thru 99-15012

99-15052 (Spring for Button)

99-15030 [ue (Lockout Flap)

a

le

171000-xxx ly “9 Pl 99.15028 iN (Ret. Button)

(Lever}

99-15054 (Pivot for Lever)

(Coin Ret. Box)

99-15056 (Screw for Bezel) 99-15038 (Bezel for Button)

Je 99-15039 \ (Bezel for Cover) 99-15036 (Cover)

99-15060

a (Sw. Cover)

Page 51

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the Specific written permission of Atari, Inc., Sunnyvale. CA This drawing 1s only conditionally issued, and neither receipt nor possession thereof conters or transfers any fight in, or license to use, the subject matter of the draw. Ing of any design or technical information shown thereon. hor any right to reproduce this drawing or any part thereo!, Except for manufacture by vendors of Atari, Inc. ‘and for manufacture under the corporation's written iicense, no right to reproduce this drawing ‘s granted or the subject matter thereo! unless by written agreement with of written permission from the corporation

171001.001 — British 10 P/10 P Coin Door 171000-002 — British 10 P/50 P Coin Door 171000-003 — British 20 P/S0 P Coin Door 171000-004 — German 1 DM/1 DM Coin Door 171000-005 — German 2 DM/1 DM Coin Door 171000-006 — German 2 DMIS DM Coin Door 171000-007 — Belgian 5 Fri5 Fr Coin Door 171000-008 — French 1 Frit Fr Coin Door 171000-009 — French 2 Fri1 Fr Coin Door 171000-010 — Swedish 1 Kr/1 Kr Coin Door 171000-011 — Hong Kong $1/$1 Coin Door 171000-012 — Canadian 25¢/25¢ Coin Door 171000-013 — U.S. 25¢/25¢ Coin Door 171000-014 — Spanish 25 Pts/25 Pts Coin Door 171000-015 — Swiss 1 Frit Fr Coin Door

Figure 23 _British-Made Coin Door 171000-xxx A

Page 52

Figure 23 _British-Made Coin Door, continued Parts List

Part No. Description

99-15001 Coin Return Button with U.S. 25¢ Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate 99-15003 Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008 Coin Return Button with Japanese 100 Yen Price Plate 39-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20¢ Price Plate 99-15011 Coin Return Button with Italian 100 Lire Price Plate 39-15012 Coin Return Button with U.S. 50¢ (2 x 25¢) Price Plate 99-15025 Left Half of Coin Inlet 99-15026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box 99-15028 Base Plate of Coin Return Box 39-15029 Switch Bracket 3939-15030 Flap for Lockout Coil (U.S. 25¢) 99-15036 Coin Return Cover 39-15037 Switch Adjuster 39-15038 Bezel for Coin Return Button 39-15039 Bezel for Coin Return Cover 39-15040 Coin Return Lever 39-15041 Lockout Coil 9399-15042 Coin Switch for U.S. 25¢ 99-15051 Lamp Holder 39-15052 Spring for Coin Return Button 39-15053 Spring for Lockout Coil 9399-15054 Pivot for Coin Return Lever 99-15055 Retaining Screw 39-15056 Screw for Both Bezels 99-15060 Switch Cover

Page 53

YOUR COMMENTS, PLEASE! rat peinting

Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A

If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person

Page: Comments:

Fill in if you wish a reply

Name _ —— a oe —

Firm — _ oo a Distributor

Address _ . — Operator GitY ecg a __ Zip _- =: Other.

Area Code Phone pace

Page 54

First fold

BUSINESS REPLY MAIL

FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA

POSTAGE WILL BE PAID BY ADDRESSEE

Atari, Inc. Attn.: Field Service/Coin-Op Division P. O. Box 427 Sunnyvale, California 94086 No Postage Necessary it mailed in the United States

aBpe siyj ode, eu iy) Buoje ynp

Page 55

9 ee eee Ue

Warranty

Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty ' (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted.

If the products described in this manuat fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:

  • Selier is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Sellers’ plant; and

defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.

In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages. t Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order. é (c) Seller's examination of said products discloses to Seller's satisfaction that such alleged

‘The use of any non-Atari paris may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety.

: Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories oihey than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.

This document is and contains confidential trade secret information of Atari, Inc.

This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for Oo any other purpose whatever, and remains the property of Atari, Inc. Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc.

Page 56

ATARI INC 1265 BORREGAS AVENUE P.O. BOX 427 SUNNYVALE, CALIFORNIA 94086 408/745-2000 ¢ TELEX 35-7488