APB TM-308 1st Printing
APB - All Points Bulletin (rev 7) (Atari Games, 1987) · Technical Manual · 72 pages · 38 sections · original scan
. . Operators Manual th iustra isl Paris Lists
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
APB" Operators Manual
with Illustrated Parts Lists
© 1987 by Atari Games Corporation All rights reserved No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored ina retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. in addition, the Act provides for payment of statutory damages of up to $250,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years. Atari Games Corporation will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.
Published by: Atari Games Corporation 675 Sycamore Drive P.O. Box 361110 Milpitas, California 95035
Printed in the U.S.A. 6R
Produced by the Atari Games Technical Publications Department
APB
Notice Regarding Non-ATARI® Parts
A WARNING A
Use of non-ATARI parts or modifications of any ATARI game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.
You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: © Substitute non-ATARI parts in the game.
- Modify oralter any circuits in the game by using kits or parts 770f supplied by Atari Games Corporation.
NOTE
This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an ATARI® game at your location, check the following: © All ground wires in the game are properly connected as shown in the game wiring diagram. © The power cord is properly plugged into a grounded three-wire outlet.
- On games provided with an Electromagnetic Interference (EMI) ground plane, be sure the game printed-circuit boards (PCBs) are properly installed on the EMI Ground Plane. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.
iv Table of Contents
Set-Up How to Use This Manual . Inspecting the Game .. Installing the Seat....... Control and Switch Locations Setting the Coin and Game Optics Game Play .... 0. eee ee .
Self-Test Main Self-Test Screen . Power-On Restart Reset High Scores Reset .. . Statistics Reset Options Report * Statistics Report .... Day Histogram Report . Sound Test ... Controls Test . Colos Bar Test . Program ROM Test . . . Motion Object ROM Test . Alphanumeric ROM Test . Playfield ROM Test . . . ARAM Test ........ Set Enhancements Demo . Can Player Die? Demo ... ns .
Maintenance Preventive Maintenance . Preventive-Maintenance Intervals . Removing the Control Panel ... Cleaning the Push-Button Leaf Switches . Maintaining the Steering Wheel . . Cleaning the Coin Mechanism . . Cleaning the Interior Components .
Corrective Maintenance. Removing the Video Display ... Removing the Steeting Wheel . . Disassembling the Steering Wheel . Reassembling the Steering Wheel Removing the Foot Pedal Removing the Game PCBs Removing the Incandescent Lights Removing the Speakers
Troubleshooting Troubleshooting Aids Troubleshooting Techniques . Soldering Techniques . . . Troubleshooting Static-Sensitive Devices .
Illustrated Parts Lists See List of Illustrations that follows.
APB Coin Information and Game Statistics Sheet See last page of this manual. 2-7 2-7 2-7 APB
APB
List of Illustrations
Figure 1-1 Control and Switch Locations ........ 0.0. c eevee erence
Figure 2-1 Main Self‘Test Screen . Figure 2-2 Power-On Restart Reset Screen . Figure 2-3 High Scores Reset Screen . Figure 2-4 Statistics Reset Screen . Figure 2-5 Options Report Screen Figure 2-6 Statistics Report Screen . Figure 2-7 Day Histogram Report Screen . Figure 2-8 Sound Test .... Figure 2-9 Controls Test .. . Figure 2-10 Color Bar Test... . . Figure 2-11 Program ROM Test . Figure 2-12 Alphanumeric ROM Test. Figure 2-13 Motion Object ROM Test . Figure 2-14 Playfield ROM Test .
Figure 3-1 Control Panel Removal Figure 3-2 Maintaining the Steering Wheel . Figure 3-3, Video Display Removal ..... . . Figure 3-4 Game PCB Removal .....-- 0.000.000.0000 ee
Figure 4-1 Removing IC (Cut-Pin Method) . Figure 4-2 Removing IC Pins Figure 4-3 Removing Solder from Plated-Through Holes . Figure 4-4 Removing Solder from Lead Connection Pads . .
Figure 5-1 Cabinet-Mounted Assemblies Figure 5-2 Control Panel Assembly ... . Figure 5-3 Steering Wheel Assembly Figure 5-4 Switching/Linear (SL) Power Supply Assembly. Figure 5-5 Foot Pedal Assembly.................-5 Figure 5-6 Coin Acceptors, Inc. Coin Door Assembly... . Figure 5-7 Printed-Circuit Board Mounting Hardware . Figure 5-8 APB Central Processing Unit (CPU) PCB Assembly Figure 5-9 APB Video PCB Assembly .. Figure 5-10 Audio II PCB Assembly ......
Table 1-1 Table 1-2 Table 1-3 List of Tables
Game Specifications Coin and Credit Option Settings Game Option Settings
vi
Safety Summary
The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found throughout this manual where they apply. 4& WARNING A Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded three-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electrical shock if the control panel is not properly grounded! After servicing any parts on the control panel, check that the grounding wite is firmly secured to the inside of the control panel. Only then should you lock up the game. AC Power Connection. Before connecting the game to the AC power source, verify that the game’s power supply is properly configured for the line voltage in your location. Disconnect Power During Repairs. To avoid ciectrical shock, disconnect the game from the AC power source before removing or repairing any part of the game. When removing or repairing the video display, extra precautions must be taken to avoid electical shock because high voltages may exist within the display circuitry and cathode-ray tube(CRT) even after power has been disconnected. Do not touch internal parts of the display with your hands or with metal objects: Always discharge the high voltage from the CRT before servicing this area of the game. To discharge the CRT; Attach one end of a large, well-insulated, 18-gauge jumper wire to ground. Momentarily touch the free end of the grounded jumper to the CRT anode by sliding it under the anode cap. Wait two minutes and discharge the anode again. Use Only ATARI Parts. To maintain the safety integrity of your ATARI game, do not use non- ATARI parts when repairing the game. Use of non-ATARI parts or other modifications to the game circuitry may adversely affect the safety of your game, and injure you or your players. Handle the CRT With Care. If you drop the CRT and it breaks, it may implode! Shattered glass can fly six feet or more from the implosion. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and curtent rating. In addition, the fuse cover must be in place during game operation.
Set-Up
How to Use This Manual
This manual is written for game operators and service personnel, and provides information for setting up, playing, testing, and maintaining your APB™ (AlJ-Points Bulletin) game. This manual is divided into the following chapters: © Chapter | contains set-up and game play information. © Chapter 2 contains self-test procedures.
- Chapter 3 contains preventive and corrective maintenance procedures. © Chapter 4 contains troubleshooting information.
- Chapter 5 contains illustrated parts lists. Wiring and schematic diagrams for the APB game circuitry are contained in the Schematic Package Supplement (SP-308) included with your game. This chapter includes information required to set up and play your APB game. Carefully read the information in this chapter before applying power to the game.
& WARNING A To avoid electrical shock, do not plug in the cabinet until it has been properly inspected and set up for the line voltage in your area. This cabinet should only be connected toa grounded three-wire outlet. If you have only a two-wire outlet, we recommend that you hire a licensed electrician to install a grounded outlet. Players can receive an clectrical shock if the cabinet is not properly grounded. Do not touch internal parts of the display with your hands or with metal objects.
SetUp
Inspecting the Game
A WARNING A
Do not plug in the game until you have completed the following inspection steps.
Please inspect your APB game carefully to ensure that the game is complete and delivered to you in good condition. Figure 5-1 shows the locations of the component parts of the game. Table 1-1 lists space, power, and environmental requirements. Inspect the factory-assembled game as follows: 1, Examine the exterior of the cabinet for dents, chips, or broken parts.
- Unlock and open the rear access panel. Unlock and open the coin doors. Inspect the interior of the cabinet as follows:
a. Ensure that all plug-in connectors (on the cabinet harnesses) are firmly plugged in. Do not force connectors together. The connectors are keyed so they only fit in the proper orientation. A reversed edge connector can damage a printed-circuit board (PCB) and will void your warranty. b. Ensure that all plug-in integrated circuits on each PCB are firmly plugged into their sockets. c. Inspect the power cord for any cuts or dents in the insulation.
d. Inspect the power supply. Make sure that the correct fuses are installed. Check that the harness is plugged in correctly and that the fuse block cover is mounted in place. Check that the green ground wires are connected.
e. Inspect other major sub-assemblies, such as the video display, printed-circuit boards (PCBs), speakers, and the incandescent lights. Make sure they are
Table 1-1 Game Specifications
Characteristic Specification
Power Consumption 240 V-A, 167 W RMS ‘Temperature +5°to +38°C (+37° to +100° F) Humidity Not to exceed 95% relative Line Voltage 105 to 130 VAC Width 25, in. (64 cm)
Depth 34 in. (86 cm) cabinet only
56 in. (142 cm) with seat installed Height 73% in. (187 cm) Weight 323 Ibs. (146 kg) APB
mounted securely and that the green ground wires are connected.
Installing the Seat The seat must be positioned in front of the cabinet before playing your APB game. Perform the following procedure to install the seat. 1, Remove the seat and four nuts from the box packed inside the shipping container.
- Remove the bolt, flat washer, and split-lock washer contained in the instruction manual bag. (An optional metal plate and four screws are also included in the bag. Use the plate and screws only if you permanently remove the seat frame from the game.)
- Unlock and open the rear access panel if not already done. 4, From the rear of the cabinet, remove the bolt holding the seat frame to the cabinet floor.
- From the front of the cabinet, pull out the seat frame to the desired distance from the control panel, until the screw holes in the frame are aligned with the screw holes in the seat bracket located on the cabinet floor.
- Place the seat on top of the seat frame. Install and tighten the four nuts underneath the seat.
- From the rear of the cabinet, place the two bolts and washers in the bracket and tighten.
- To reposition the seat frame for moving or shipping the cabinet, reverse the order of steps 2 through 7. Be sure to keep the seat (if removed) and its hardware in. a convenient place for future use.
APB
Control and Switch Locations
Power On/Off Switch The power on/off switch is located at the bottom rear of the cabinet. (See Figure 5-1.)
Volume Control The volume control is located on the Audio 1 PCB behind the upper coin door. (See Figure 1-1.) The volume contro} adjusts the level of sound produced by the game.
Coin Counter The coin counter is located on the shelf behind the upper coin door. The coin counter records the number of coins deposited.
Game Option Switch
Coin Counter
Aurxillary Coin Switches Coin Option Switch
CPU PCB Set-Up
Self-Test Switch The self-test switch is located on the Audio I PCB behind the upper coin door, (See Figure 1-1.) The self-test switch selects the Self-Test Mode to check game operation. Refer to Chapter 2 for a complete description of self-test operation.
Setting the Coin and Game
Options
The APB cabinet has two dual-in-line package (DIP) option switches located on the CPU printed circuit board (PCB). (See Figure 1-1.) © The option switch at location 6/7A and switches 1 and 2 at location 5/6A are for selecting coin options. © The option switches 3-7 at location 5/6A are for selecting game options.
Figure 1-1 Control and Switch Locations
Set-Up
Set the coin and credit option settings by changing the settings of the DIP switches. Refer to Table 1-2 and Table 1-3 for the available options and default (recommended) settings. To change the coin and credit settings, first remove the thin film of plastic covering the option switch. Use a pen or a sharp-pointed instrument to slide the appropriate small buttons to different settings. Right is the on position, and left is the off position. The steering wheel and the push buttons are 7of used to change these settings.
Game Play
This section of the manual describes the theme of the APB game, the operating modes, and the game play features.
Introduction APB is a unique driving/shooting gare where the player Pottrays Officer Bob in his action-packed pursuit of common law-breakers and hardened criminals. APB features a 360° steering wheel and multi-directional scrolling to allow players to explore the highways and byways of Bob’s beat.
Attract Mode The Attract Mode begins when the game is powered up or after exiting the Play or Self-Test Modes. The Attract APB
Mode ends when coins or tokens are inserted and the start button is pressed. The Attract Mode continuously cycles through the following displays: © High score table © APB title screen
- Game play demonstration
Unique Features to Attract Players © Numerous detailed animation sequences are included to add humor and enhance player enjoyment, as well as create player involvement with the many characters found in the game. © Multi-directional scrolling allows players to drive in all directions on the screen. Players are encouraged to explore the streets and back roads of Bob’s beat in their constant, action-packed pursuit of law-breakers. The unique upright cabinet configuration features a compact, operator-adjustable sitdown-style seat for player comfort along with a dynamic overhead attraction panel.
Play Mode APB is the ultimate cops-and-robbers game in which players portray Officer Bob. The levels of game play are measured in days. In order to progress to the next level, play-
Table 1-2 Coin and Credit Option Settings
Settings of 8-Toggle Switch on APB CPU PCB (at 6/7A) 1 2 3 4 5 6 7 8 Option
Coins Per Credit
| Off | Off | 1 Coin 1 Credit <4 |
| Off | On | 2 Coins 1 Credit |
| On | Off | 3 Coins 1 Credit |
| On | On | 4 Coins 1 Credit |
Right Coin Mechanism
| Off | Off | 1 Coin Counts as 1 Coin <4 |
| Off | On | 1 Coin Counts as 4 Coins |
| On | Off | 1 Coin Counts as 5 Coins |
| On | On | 1 Coin Counts as 6 Coins |
Left Coin Mechanism Of 1 Coin Counts as 1 Coin~4 On 1 Coin Counts as 2 Coins Bonus Adder
| off | Off | Off | No Bonus Adder <4 |
| Off | Off | On | 2 Coins Give 1 Extra Coin |
| Off | On | Off | 4 Coins Give 1 Extra Coin |
| Off | On | On | 4 Coins Give 2 Extra Coins |
| On | Off | Off | 5 Coins Give 1 Extra Coin |
| On | Off | On | 3 Coins Give j Extra Coin |
| On | On | On | Free Play |
<4 Manufacturer's recommended settings
1-4
APB Set-Up
Table 1-3 Game Option Settings
Settings of 8-Toggle Switch on APB CPU PCB (at 5/6A)
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | Option |
—_ Asof press time, this switch is not used and has no effect. However, refer to the Report Options screen in self-test to be sure. Add-A-Coin Control
| Off | On | Maximum of 3 Add-A-Coin Games |
| On | Off | Maximum of 10 Add-A-Coin Games |
| Off | Off | Maximum of 25 Add-A-Coin Games <4 |
| Qn | On | Unlimited Add-A-Coin Games |
Game Difficulty +ssee++.. How Setting AffectsGame Play .. . No. of Demerits Bonus Increments Perfect Allowed Every __ Pts. Day Bonus
| Off | On | On | Hardest | 4 | 18,000 | No |
| Off | Off | On | Very Hard | 5 | 15,000 | No. |
| Off | On | Off | Hard | 6 | 13,000 | Yes |
| On. | Off | Off | Medium Hard | a | 11,000 | Yes |
| Off | Off | Off | Medium Easy <4 | 8 | 10,000 | ‘Yes |
| On | Off | On | Easy | 9 | 8,000 | ‘Yes |
| On | On | Off | Very Easy | 10 | 6,000 | Yes: |
| On | On | On | Easiest | ih | 5,000 | Yes |
Start Game/Add-A-Coin Ratio
| Off | On | 1:1 (1 Credit to Start/l Credit to Continue) |
Off = Off 2:1 (2 Credits to Start/l Credit to Continue) 4
| On | On | 3:1 G Credits to Start/1 Credit to Continue) |
| On | Off | 3:2 3 Credits to Start/2 Credits to Continue) |
Manufacturer's recommended settings
ers must arrest a daily quota of law-breakers or arrest the APB criminal of the day and return to the police station. There are multiple objectives to challenge both novice and experienced players: 1, Make the daily quota by arresting the offenders (litterbugs, drunks, dopers, honking taxis, hitchhikers, bikers, speeders and others);
- Send APB criminals to jail (Sid Sniper, Juan Fingers,” Freddy Freak, Hans Oop and many more);
- Collect bonus time, extra fuel, and police car enhancements. The game is over when the player obtains too many demerits: Demerits are given for not arresting the day’s quota of criminals, for shooting innocent vehicles, crashing the police car, running out of gas, etc. Controls consist of a 360° steering wheel, a siren button, a fire button, and a gas pedal, In order to make an arrest, players must press the siren button and tag the lawbreaker. The fire button can be used after the player has picked up the gun car enhancement from the speed shop. By driving through the speed shop, players can select from several different enhancements for their police cars, including: faster acceleration, higher top speed, radar, armor, guns, and better brakes. Players can acquire many levels of these enhancements. The ability to build amore powerful police car is an added incentive for players to use the add-a-coin game continuation and maintain their vehicles.
Players continue to be challenged as they portray Officer Bob through an unlimited number of game play levels. Add-a-coin game continuation and level select features are included for increased earning power.
High Score Mode Upon completing a game and if players are among the top 25 scorers recorded on the game, they have several seconds to enter their initials before the game returns to the attract mode. Players select their initials by moving the steering wheel and pressing the siren button when the proper initial is displayed. To encourage high score competitiveness among players, you can periodically reset the high score table through the self-test. The top cight scores are kept in memory, while scores 9 through 25 are reset daily during powerup. Resetting the top eight scores in the self-test will give new players a chance to be recognized as top APB players.
1-5
Set-Up
Hints for Game Play © To obtain higher scores, players should search off-road and collect bags of money and doughnuts. ¢ Players should try to complete the lowest car quota as soon as possible. (Another quota item may replace it.) © For a chance at receiving hints toward the mystery APB, players should meet the quota and return the APB criminal to the police station. To have one demerit removed, players shouldstrive to play a perfect day (except Day 1).
Game Difficulty Options The game difficulty option settings for APB (see Table
- represent a totally new approach for Atari Games. We believe this new style of option table will make it easier for operators to adjust APB to suit players ofall skill levels. By changing one setting, the operator adjusts several game variables at the same time:
- Demerits Allowed: Similar to the typical game concept of “lives”, the game is over when the piayer gets more than the number of demerits allowed.
- Bonus Increments: One demerit is erased at the indicated score multiples.
- Perfect Day Bonus: One demerit is erased for completing a perfect day. A perfect day means catching the daily quota of criminals and not bumping the police car into any other obstacles. The player does mot have to arrest the APB criminal of the day. The game difficulty option setting also affects a few other, more subtle, game tuning elements. These elements are gas usage, day timer clock speed, and the collision speed necessary to make the player’s car explode. Game difficulty options should be changed by only one Setting at a time. Changing from “medium easy” to “‘medium hard” will shorten the average game time by 10 to 20 seconds, depending upon the players in the location.
Maximizing Earnings Operator options on this game have been kept very simple. Enter Self-Test and use the Report Statistics screen to evaluate game data. The Report Options screen can be used to make adjustments to game difficulty and coinage. The key to maximum earnings is striking a midpoint on game times. Game times must be short enough so that player turnover is high. Conversely, game times must be long enough to give a player a good value and insure repeat play (repeat play is crucial to longevity). APB gives the operator flexibility to tune game difficulty and enough statistics to intelligently make adjustments. If collections seem low or are dropping off, the most important thing to do is check all player controls and coin
1-6 APB
mechanisms for proper operation before making any other changes. As with all games, APB must be in proper working order to maximize earnings. When evaluating the average game time, consider the price that the player is paying to play the game. In order to give players good value for their money, the average time for new games should be somewhat longer for APB games that are set for two coins to start (a minimum of 2:30 versus 1:30 for games set for one coin to start). The average game time for continued games will be shorter than that for new games, due to the increasing difficulty of the game.
If earnings seem low, the game is technically sound and the average game time is too short, try changing the game difficulty option to an easier setting. This change will give players more game time for their money. If the average game time per quarter is too long, try changing the game difficulty to a harder setting. If the average game time per quarter is still too Jong after a few weeks, try an even harder setting. After changing the game difficulty settings, it is a good idea to reset the game statistics. The histograms should be cleared by following the instructions in Self-Test (this resets the average game time statistics).
Game Sounds Your APB game uses more effective audio than previous games, which results in more player involvement and enjoyment. The game uses advanced digital sound-generation techniques to create realistic musical instrument sounds (such as clarinets, harmonicas, drums, and violins). Although a player may not be consciously aware of the music, it has a direct effect on the excitement and emotional experience of the game. The APB game creates ear-catching sound effects, which are designed to give feedback to make the player believe that the game is responding directly to his actions. To maximize the player's enjoyment of this enhanced audio and maximize your earnings, consider the following hints:
- The game iocation should be a relatively dead acoustical environment. The goal is to minimize unnecessary sound reflection, so that the sounds from the APB game won't be drowned out by the accumulation of other sounds that bounce around the room. Carpets help eliminate sound reflections from the floor. Acoustical tile is also useful, especially if you have low ceilings.
- If you use an environmental sound system or a stereo, consider lowering its volume or perhaps even turning it off. In the days when video games just made harsh beeps and boops, a central sound system helped make up for the lack of drive and excitement in a game’s sounds. But your APB game is very musical, and a sound system interferes with the game’s ability to interest players and draw bystanders.
3, Be concerned with the overall volume levels in arcade environments. The goal is to involve the players’ emo- Set-Up
tions, not to damage their hearing. To a certain point, raising the game volume helps add to player excitement, but above that level it creates hearing fatigue and the high volume starts to drive players away. Rather than turning up the volume on the APB games to cut through the background sound level, try lowering the volume of any neighboring games that have sounds which are not an attractive or important element. Careful placement of games and attention to unnecessary noise sources can also help increase the player’s sense of game involvement and interaction.
HANS OOP
FREDDY FREAK
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Chapter 2
Self-Test
The APB™ game tests itself and provides visual and audible indications of the condition of the game circuitry and controls, Self-test information is displayed on the screen and through the sound system. No additional equipment is required. We suggest that you perform a self-test when you first set up the game, each time you collect the money, or when you suspect game failure. When the self-test switch is turned on, the game enters the Self-Test Mode. The Main Self-Test screen is displayed and lists 16 self-tests that provide information pertaining to the game circuits and controls. Turning the self-test switch off at any time during the Self-Test Mode, except for the demo items, causes the game to return to the Attract Mode. Refer to Chapter 1 for the location of the selftest switch.
Self-Test
Main Self-Test Screen
The Main Self-Test screen is shown in Figure 2-1. This screen lists four categories of operator-selectable APB self-tests and game statistics: Reset, Report, Test, and Demo. They consist of: Power-On Restart Reset, High Scores Reset, Statistics Reset, Options Report, Statistics Report, Day Histogram Report, Sound Test, Controls Test, Color Bars Test, Program ROM Test, Alphanumeric ROM Test, Motion Object ROM Test, Playfield ROM Test, All RAM Test, Set Enhancements Demo, and Can Player Die? Demo.
Turning the steering wheel counterclockwise sequences down through the list of tests; turning the wheel clockwise sequences up through the list. Then pressing the Siren button selects the self-test and, if applicable, displays the self-test screen.
Power-On Restart Reset
The Power-On Restatt Reset screen is shown in Figure 2-2. This option performs a power-on type reset of the game. The RAM test checks the condition of the zero page RAM, motion object RAM, playfield RAM, and alphanumeric RAM. If this test fails, the message BAD is displayed in red and shows the code for the failed RAM. The ROM test checks ali eight of the program ROMs on the CPU PCB for check sums. If this test fails, the message BAD is displayed in red and shows the code for the failed ROM.
Figure 2-1 Main Self-Test Screen
2-2 APB
Figure 2-2 Power-On Restart Reset Screen
The 6502 Processor test indicates the condition of the 6502 sound microprocessor and associated circuitry. The 6502 test starts with a reset/communications check for proper response to start up protocol. The test then checks the communications ports (T-11 to 6502 and 6502 to T-11), the 6502 reset circuit, and the general condition of the 6502. If the 6502 circuitry does not respond properly to the reset, the system retries the reset procedure ten times. If the 6502 circuitry fails to reset through all ten attempts, the message BAD is displayed. The Switch test checks the condition of the push-button leaf switches. If a leaf switch is stuck or is not functioning properly, the message BAD is displayed. Select this option on the Main Self-Test screen by turning, the steering wheel, then press the Siren button. The message Are you SURE? Hit SIREN and FIRE if yes. is displayed. Pressing the Siren and the Fire buttons simultaneously resets the game. After the test is completed, the message GAME MANAGER: Use WHEEL and SIREN is displayed at the top of the screen. Turn the steering wheel to return to the Main Self-Test screen,
High Scores Reset The High Scores Reset screen is shown in Figure 2-3. This option resets the high score table to the factory settings. Select this option on the Main Self-Test screen by turning the steering wheel, then press the Siren button. The message Are you SURE? Hit SIREN and FIRE if yes. is displayed. Pressing the Siren and the Fire buttons simultaneously resets the high scores. The message DONE is then displayed on the screen. Turn the steering wheel again to return to the Main Self- Test screen.
APB
Figure 2-3 High Scores Reset Screen
Figure 2-4 Statistics Reset Screen
Statistics Reset The Statistics Reset screen is shown in Figure 2-4. This option resets the current game statistics. The statistics information is accumulated from the last time the statistics Were reset.
Select this option on the Main Self-Test screen by turning the steering wheel, then press the Siren button. The message Are you SURE? Hit SIREN and FIRE if yes. is displayed. Pressing the Siren and the Fire buttons simultaneously resets the game statistics. The message Please wait is displayed on the screen. Then after several seconds, the message SUCCESS is displayed. Turn the steering wheel to return to the Main Self-Test screen.
Options Report The Options Report screen is shown in Figure 2-5. This screen indicates the current coin and game option set- Self-Test
Figure 2-5 Options Report Screen
tings of the two dual-in-line package (DIP) switches at locations 6/7A and 5/6A on the CPU PCB.
- The option switches at location 6/7A and switches 1 and 2 of the option switches at location 5/6A are used for selecting the coin and credit options.
- The option switches 3 through 7 at location 5/6A are for selecting game options. Select this option on the Main Sel£Test screen by turning the steering wheel, then press the Siren button. Set the coin and game option settings by changing the settings of the DIP switches located on the CPU PCB. Refer to Tables 1-2 and 1-3 in this manual for the available options and default (recommended) settings. To change these settings, first remove the thin film of piastic covering the option switch. Use a pen or a sharppointed instrument to slide the appropriate small buttons to different settings. With the PCB installed in the game, right is the on position, and left is the off position. The steering wheel and the push buttons are ot used to change these settings. After changing the switch settings, press the Siren button to redispiay the settings. Turn the steering wheel to return to the Main Self-Test screen.
Statistics Report The Statistics Report screen is shown in Figure 2-6. This screen provides a visual check of the current game statistics, showing the distribution of times for starting games. These times are measured from game start to the first adda-coin, or from game start to game end if no coin is added. The number of games in each category is indicated numerically and as a bar graph. The statistics information is accumulated from the last time the statistics were reset. The green-highlighted reading indicates the number of new games. The red-highlighted reading indicates the number of continued games.
2-3
Self-Test
Figure 2-7 Day Histogram Report Screen
Select this option on the Main Self-Test screen by turning the steering wheel, then press the Siren button. Turn the steering wheel to return to the Main Self-Test screen.
Day Histogram Report The Day Histogram Report screen is shown in Figure 2-7 and gives a failure/success measure for each day. The number of games in each category is indicated numerically and as a bar graph. The green-highlighted reading indicates the number of times a day was started. The redhighlighted reading indicates the number of times a day was successfully completed. Select this option on the Main Self-Test screen by turning, the steering wheel, then press the Siren button. Turn the steering wheel to return to the Main Self-Test screen.
2-4 APB
Sound Test The Sound Test screen is shown in Figure 2-8. This test indicates the condition of the sound-effects circuits, including the music (Yamaha) synthesizer, sound-effects generator (POKEY) sound outputs, and the speech chip. Select this test on the Main Self-Test screen by turning the steering wheel, then press the Siren button, Next, turn the steering wheel clockwise to sequence forward through the sounds; turn the steering wheel counterclockwise to sequence backward. After selecting the desired sound, press the Siren button to start the sound. Select STOP to turn off the sound during the test.
To return to the Main Self-Test screen, turn the wheel to select EXIT, the last item displayed on the screen. Next, press the Siren button and then turn the steering wheel.
Controls Test The Controls Test screen is shown in Figure 2-9. This test indicates the condition of the steering wheel, foot pedal, and push-button leaf switches. The PEDAL message displays the low, high, range, raw, and normalized values of the foot pedal. These values
Figure 2-8 Sound Test
APB Self-Test
Figure 2-9 Controls Test
should increase as the pedal is pressed. The message Range OK is displayed if the pedal is functioning properly. The message Range BAD. Press pedal. is displayed if the pedal is malfunctioning. The SWITCH message displays the two types of push-button switches: Siren, and Fire. Pressing the respective button should highlight the button name on the screen, The WHEEL message displays hexadecimal values of instantaneous (left value) and accumulated (right value) readings. Look for consistent readings (within + 2) when you turn the steering wheel to its left and right limits. As you turn the wheel clockwise, a green circle indicating a clockwise direction is drawn simultaneously on the screen; as you turn it counterclockwise, a blue circle is drawn simultaneously in a counterclockwise direction. Turn the wheel until the message Hit siren to exit. is displayed, then press the Siren button. Turn the wheel to return to the Main Self-Test screen.
Color Bar Test
The Color Bar Test consists of several coior display screens that indicate the condition of the video display color circuits. These screens are used to test for white tracking, color purity, and convergence. One of the screens is shown in Figure 2-10.
This test begins with a screen displaying fifteen horizontal color bars beginning with lavender, yellow, red, blue, and green. These same colors are then repeated in sequence except that each color is separated by a white horizontal Figure 2-10 Color Bar Test
bar. In the next screen display, vertical color bars of green, white, blue, white, red, white, yellow, white, lavender, and white are repeated across the screen. Next follow five Color Bar screens that indicate the condition of the display color-purity circuits. These consist of individual color screens of red, green, blue, white, and grey. If the display characteristics are not correct, refer to the display manual included with your game for the colorgun adjustment procedure or to determine the possible cause Of failure. The four Convergence Test screens that follow indicate the condition of the display size, centering, linearity, and convergence. Initially, a white-dot convergence pattern is displayed foiiowed by purple-, cyan- (blue-green), and. yellow-dot screens. Convergence between any two colors should not exceed 0.7 mm in the middle of the screen and 1.2 mm in the corners. This pattern can also be used to adjust screen size, centering, and brightness (black level). To obtain the proper screen size, adjust the pattern to be as large as the face of the CRT: all four pattern corners should be just at the corners of the CRT. After adjusting the screen size, check the game playfield: verify that the score information is on the screen. For white tracking purposes, a screen showing sixteen vertical grey-scale bars and three groups of sixteen vertical bars with shades of red, green, or blue is displayed. Each group of red, green, or blue should be split in half horizontally to show two fade scales. Each upper fade scale is ranged by changes in overall color intensity (z) and each lower fade scale by individual color intensity (R, G, B). This test helps to determine if white tracking is set properly (grey-scale bars range from white to grey). Select this test on the Main Self-Test screen by turning the steering wheel, then press the Siren button. Turn the steering wheel to return to the Main Self-Test screen.
2-5
Self-Test
Program ROM Test The Program ROM Test screen is shown in Figure 2-11. During this test the eight program ROMs on the CPU PCB are tested for check sums. If the ROM test fails, a red message ERROR with the location of the failed ROM is displayed. If the ROM test is good, a white message OK is displayed. Select this test on the Main Self-Test screen by turning the steering wheel, then press the Siren button. Turn the steering wheel to return to the Main Self-Test screen.
Motion Object ROM Test The Motion Object ROM Test screen is shown in Figure 2-12. This test indicates the condition of the motion-object ROMs, horizontal and vertical display locations, and. motion-object color palettes.
Figure 2-11 Program ROM Test APB.
Select this test on the Main Self-Test screen by turning the steering wheel, then press the Siren button. Next, turn the wheel and all game pictures are displayed one at a time. Ifa picture cannot be made the correct color by pressing the Siren button, then a ROM is bad. Turn the steering wheel to return to the Main Self-Test screen.
Alphanumeric ROM Test The Alphanumeric ROM Test screen is shown in Figure 2-13. This screen indicates the condition of the alphanumeric ROM, and color palettes. This screen shows five rows Of alphanumeric characters under the title Alphanumeric ROM Test: the first row with white, uppercase characters followed by a second row with red, uppercase characters; the third row with green, lowercase characters; and the fourth row with yellow, uppercase characters. The fifth row tests the color palettes and displays eight “color” words: white, red, yellow, green, blue, purple, and “flashing” purple. Select this test on the Main Self-Test screen by turning the steering wheel, then press the Siren button. Turn the steering wheel to return to the Main Self-Test screen.
Playfield ROM Test The Playfield ROM Test screen is shown in Figure 2-14, This screen indicates the condition of each playfield ROM, and the vertical and horizontal playfield scrolling registers. . For each of the four ROM pairs, the screen displays one picture and the ROM pair PCB location. Select this option on the Main Self-Test screen by tumning the steering wheel, then press the Siren button. Consec-
Figure 2-12 Alphanumeric ROM Test Figure 2-13, Motion Object ROM Test
APB
Figure 2-14 Playfield ROM Test
utive pressing of the Siren button sequences through the ROM locations and their corresponding game pictures. Turn the steering wheel to return to the Main Self-Test screen.
All RAM Test
The All RAM Test instructs the operator to do a power-on restart to test the RAM.
Select this option on the Main Self-Test screen by turning the steering wheel, then press the Siren button, The message To test all RAM do RESET power-on restart. is displayed. Self-Test
Select the Power-On Restart reset option on the Main Self- Test screen by turning the steering wheel, then press the Siren button. The message Are you SURE? Hit SIREN and FIRE if yes, is displayed. Pressing the Siren and the Fire buttons simultaneously resets the RAM. The message GAME MANAGER: Use WHEEL and SIREN is displayed after the test is completed. Turn the steering wheel to return to the Main Self-Test screen.
Set Enhancements Demo The Set Enhancements Demo screen is for demonstration purposes only, and sets the player enhancements to the maximum available for the day (level) being played. Select this option on the Main Self-Test screen by turning the steering wheel, then press the Siren button. The message DONE is displayed. Turn the steering wheel to make a different selection on the Main Self-Test screen.
Can Player Die? Demo The Can Player Die? Demo is for demonstration purposes only, and prevents players from dying during the demo. Select this option on the Main Self-Test screen by turning, the steering wheel, then press the Siren button. The message NO is displayed. Pressing the Siren button again, displays the message YES. Turn the steering wheel to make a different selection on the Main Self-Test screen.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Chapter 3
Maintenance
This chapter includes preventive and corrective maintenance procedures for the APB™ game components that are subject to the most use. To assure maximum troublefree operation from this game, we recommend that preventive maintenance be performed as described in this chapter. Removal, disassembly, reassembly, and replacement procedures are provided for components that might require corrective maintenance. Appropriate references are provided to Chapter 5, Illustrated Parts Lists, to help locate the parts of this game that are mentioned, but not illustrated, in the maintenance procedures.
Maintenance
Preventive Maintenance
Preventive maintenance includes cleaning, lubricating, and tightening hardware. How often preventive maintenance is performed depends upon the game environment and frequency of play. However, for those components listed in Table 3-1 Preventive-Maintenance Intervals, we recommend that preventive maintenance be performed at the intervals specified.
Preventive-Maintenance
Intervals
The preventive-maintenance intervals specified in Table 3-1 are the recommended minimum requirements for the components listed.
A WARNING A
To avoid possible electrical shock, turn off the game before performing any maintenance procedures.
Removing the Control Panel
Perform the following procedure to remove/replace the control panel. (See Figure 3-1.)
- Unlock and open the rear access panel.
- Carefully reach through the rear access panel opening and release the spring draw latches located under the control panel on both sides of the cabinet.
- Use a 5/32-inch Allen wrench to remove the two screws and washers holding the front of the control panel to the cabinet. 4, Grasp the steering wheel control and gently lift until the bottom edge of the control panel clears the cabinet.
- Disconnect the control panel harness connector and remove the control panel from the cabinet.
Table 3-1 Recommended Preventive- Maintenance Intervals
Steering Wheel Inspect weekly, lubricate, and tighten hardware at least every three months. Foot Pedal Lubricate and tighten hardware at least every three months. Coin Mechanism Inspect whenever you collect coins. Clean at least every three months.
3-2
- Replace the control panel in the reverse order of removal.
Cleaning the Push-Button Leaf
Switches
Perform the following procedure to clean the leaf switch contacts and tighten the securing hardware.
- Follow the procedure described in the preceding steps 1-5 for removing the control panel.
- Use electrical contact cleaner to clean the contacts. Do not burnish them. When the push button is pressed, the wiping action of the cross-bar contacts provides a self-cleaning feature.
- Using a '%.-inch open-end wrench, tighten the stamped nut securing the push-button leaf switches to the control panel.
Maintaining the Steering Wheel
Preventive maintenance on the steering wheel consists of:
Inspecting the steering wheel housing for excessive wear or dirt.
- Inspecting the Optical Coupler PCB Assembly for damage. Lubricating the friction-producing surfaces of the white bearings. Replacing or tightening the securing hardware if necessary. Perform the following procedure to lubricate and tighten the steering wheel control. (See Figure 3-2.)
- Open the control panel as previously described.
- Apply white grease (Atari part no. 107027-001) to the lubrication points shown in Figure 3-2.
- Using a {inch nut driver (or an appropriate tool), tighten the screws holding the steering wheel assembly to the control panel.
Cleaning the Coin Mechanism Use a soft-bristled brush to remove loose dust or foreign material from the coin mechanism. A toothbrush can be used to remove any stubborn build-up of residue in the coin path. After cleaning the coin mechanism, blow out all of the dust with compressed air.
APB Maintenance
Spring Draw Latch Control Panel
Harness Connector Coin Door
Figure 3-1 Control Panel Removal
Cleaning the Interior
Components
Perform the following procedure to clean the components inside the cabinet.
| A WARNING A
Turn off the game power, but do not unplug the power cord before cleaning inside the cabinet. ‘The power cord provides a ground path for stray static voltages that can be present on the cleaning tools.
- Unlock and open the rear access panel.
- Discharge the high-voltage from the cathode-ray tube (CRT) before proceeding. The display assembly contains a circuit for discharging the high voltage to gcound when power is removed. However, to make certain, always discharge the display as follows. a. Attach one end of a large, well-insulated, 18-gauge jumper wire to ground. b. Momentarily touch the free end of the grounded jumper to the CRT anode by sliding it under the anode cap.
¢. Wait two minutes and repeat part b.
. Use a vacuum cleaner with a soft long-bristled brush attachment or use a soft-bristled paint brush to remove loose dirt and dust accumulated on the inside of the cabinet. Be sure to clean the electrical components thoroughly (power supplies, PCB assemblies, display, etc.).
3-3
Maintenance APB
Steering Wheel Lock Washer
Logo Cover
Bolt
Housing
Thompson Bearing
Coupler PCB Assy
Encoder Hub
Figure 3-2 Maintaining the Steering Wheel
Corrective Maintenance
Corrective maintenance consists of removal, disassembly, following procedures are provided for components that reassembly, and replacement of game components. The may require corrective maintenance.
3-4
Removing the Video Display
Perform the following procedure to remove/replace the video display. (See Figure 3-3.)
- Tum the game power off and wait two minutes. Unplug the power cord. 2, Remove the control panel as described in Preventive Maintenance.
- Reach up through the panel slot underneath the bezel with your fingers and press forward on the display shield to pry it loose from the cabinet.
- Grasp the display shield on the bottom edge and gently pull it out from the cabinet.
- Use a flat-head screwdriver to remove the staples, if any, securing the bezel to the cabinet. Remove the bezel.
- Unlock and open the rear access panel.
A WARNING A
High Voltage The video display contains potentially lethal high voltages. To avoid injury, do not attempt to service this display until you observe all precautions necessary for working on high-voltage equipment. X-Radiation The video display has been designed to minimize Xradiation. However, to avoid possible exposure to soft X-radiation, never modify the high-voltage circuitry. Implosion Hazard The cathode-ray tube may implode if struck or dropped. Shattered glass may cause injury within a 6foot radius. Use care when handling the display. 7.
10. Maintenance
Discharge the high-voltage from the cathode-ray tube (CRT) before proceeding. The display assembly contains a circuit for discharging the high voltage to ground when power is removed. However, to make certain, always discharge the display as follows. a. Attach one end ofa large, well-insulated, 18-gauge jumper wire to ground. b. Momentarily touch the free end of the grounded jumper to the CRT anode by sliding it under the anode cap. c. Wait two minutes and repeat part b. . Disconnect the video signal and the display power comnectors. . Use a %inch nut driver to remove the four sets of nuts and washers from the corners of the video display chassis. Remove the two hex-head screws from the bottom corners of the chassis. Carefully slide the display out through the front of the cabinet. . Replace the video display in the reverse order of removal.
Display Bezel
Display Shield Nut and Washer
Figure 3-3 Video Display Removal
3-5
Maintenance
Removing the Steering Wheel
Perform the following procedure to remove/replace the steering wheel. (See Figure 3-2.)
- Open the control panel as described under Preventive Maintenance.
- Disconnect the harness connectors from the coupler PCB connector.
- Using a %.-inch nut driver, remove the six screws holding the steering wheel assembly to the control panel. 4, Lift the steering wheel assembly out of the control panel.
- Replace the steering wheel in the reverse order of removal. Reconnect the harness connectors to the coupler PCB connector.
Disassembling the Steering
Wheel
Perform the following procedure to disassemble the steering wheel assembly. (See Figure 3-2.)
- Using a %<inch nut driver (or appropriate tool), remove the six screws holding the steering wheel assembly to the control panel.
- Using a %-inch nut driver (or appropriate tool), remove the bolt and washer from the bottom of the encoder hub.
- Pull the shaft from the housing. 4, Remove the three screws holding the cover to the shaft.
- Remove the %-inch x 1-inch screw from the shaft.
Reassembling the Steering
Replace the steering wheel parts in the reverse order of removal. After reassembling the steering wheel, be sure that the hub can spin freely in the slot of the optical coupler on the PCB.
Removing the Foot Pedal
Perform the following procedure to remove/replace the foot pedal. (See Figure 5-6.)
- Disconnect the foot pedal cable assembly from the main harness assembly located inside the rear of the cabinet.
- Using a %inch hex driver (or appropriate tool), remove the two bolts and washers holding the foot pedal frame to the cabinet base. Remove the foot pedal.
- Replace the foot pedal in the reverse order of removal. APB
Removing the Game PCBs
Perform the following procedure to remove/replace the game PCBs,
Video PCB Perform the following procedure to remove/replace the Video PCB. (See Figure 3-4.) 1.
2.
3. Turn the game power off. Unlock and open the rear access panel. Remove the four thumb nuts holding the EMI cover to the ground plane. . Disconnect the harness connectors from the bottom of the Video PCB. . Remove one of the two thumb screws and spacers holding the top of the Video PCB (and the bottom of the CPU PCB) to the ground plane. Loosen, but do not remove, the other thumb screw.
10. . Remove the two thumb screws holding the bottom of the Video PCB to the ground plane. Carefully hold the Video PCB in place to prevent the PCB from falling or causing excessive bending at the edge connector. . Remove the remaining thumb screw and spacer that was loosened in step 5. Gently disconnect the Video PCB from the CPU PCB. . Replace the Video PCB by first connecting the Video PCB to the CPU PCB edge connector. Carefully position both the Video and CPU PCBs so that the holes (in the bottom of the CPU PCB and at the top of the Video PCB) are aligned. Partially install one thumb screw and spacer through both of the PCBs and into the corresponding ground plane post. . Install and tighten the two thumb screws holding the bottom of the CPU PCB to the ground plane. Install the remaining thumb screw holding the top of the Video PCB (and bottom of the CPU PCB) to the ground plane.
Maintenance
CPU Printed-Circuit Board
EMI Cover Edge Connector
Figure 3-4 Game PCB Removal
- Finger-tighten both thumb screws holding the top of the Video PCB (and bottom of the CPU PCB) to the ground plane.
- Connect the harness connector to the bottom of the Video PCB,
Maintenance
CPU PCB Perform the following procedure to remove/replace the Central Processing Unit (CPU) PCB. (See Figure 3-4.)
- Turn the game power off.
- Unlock and open the rear access panel.
- Remove the four thumb nuts holding the EMI cover
10.
11. to the ground plane, . Disconnect the harness connectors from the left edge of the CPU PCB. . Remove the four thumb screws holding the CPU PCB (and the top of the Video PCB) to the ground plane. . Gently disconnect the CPU PCB from the Video PCB. . Replace the CPU PCB by first connecting the CPU PCB to the Video PCB edge connector. Carefully position both the CPU and the Video PCBs so that the holes (in the bottom of the CPU PCB and at the top of the Video PCB) are aligned. Partially install one thumb screw and spacer through both of the PCBs and into the corresponding ground plane post. . Install and tighten the two thumb screws holding the top of the Video PCB to the ground plane. . Install the remaining thumb screw holding the bottom of the CPU PCB (and the top of the Video PCB) to the ground plane. Finger-tighten both thumb screws holding the bottom of the CPU PCB (and the top of the Video PCB) to the ground plane. Connect the harness connectors to the left edge of the CPU PCB. (See Figure 3-4 for the proper connector locations.)
Removing the Incandescent
Lights
Pert ‘form the following procedure to remove/replace the incandescent lights. 1.
2.
3-8 Turn the game power off. From the front of the cabinet, use a 4-inch hex driver to remove the six screws and washers holding the curved attraction shield to the top of the cabinet. APB
A WARNING A
‘When working near the light bulbs, be sure that you do not touch them until they have cooled—or about five minutes.
3.
4,
5. Unscrew each light bulb and remove them from the sockets.
To remove the entire light fixture, use a Phillips screwdriver to remove the two screws holding the lightboard panel to the cabinet. Then disconnect the light harness connector in the rear of the cabinet. Using a screwdriver, remove the two screws holding the light base and lift the base out of the front of the cabinet. Replace the light fixture in the reverse order of removal.
Removing the Speakers Perform the following procedure to remove/replace the speakers. 1.
2, Turn the game power off. From the front of the cabinet, use a %-inch hex driver to remove the four screws holding the speaker cover grille to the cabinet. . Use a Phillips screwdriver to remove the six screws holding the front of the speaker panel to the cabinet. . Disconnect the speaker harness assembly. . Remove the speaker panel.
. Use a Phillips screwdriver to remove the four screws holding the speaker to the cabinet. Do not let the speaker fall. . Lower the speaker just far enough to disconnect the two speaker wires. Be sure that you hook up the wires correctly. Otherwise, the game will produce less than the desired volume because the speakers will be out of phase. The signal wire on each speaker should be attached to the speaker tab marked with color, a + sign, or a round dot. (The signal wires are shown on the game wiring diagram; refer to the Schematic Package included with the game.) . Replace the speaker in the reverse order of removal.
Chapter 4
Troubleshooting
The information in this chapter discusses troubleshooting aids and techniques to assist the service technician when. trouble is suspected in a game. Most troubles can be located quickly by following the information in this chapter. However, if problems persist, contact your local distributor or your Atari Games Corporation Customer Service Office, listed on the inside front cover of this manual, for assistance.
Troubleshooting
Troubleshooting Aids
Troubleshooting aids are provided throughout this manual and the schematic package supplement. The following information is intended to acquaint the service technician with the portions of these documents that contain useful troubleshooting and repair information.
Assembly and Component Locations The parts lists in Chapter 5 of this manual illustrate the locations of assemblies and components. Printed-circuit board (PCB) illustrations aid in rapidly locating components shown on the corresponding schematic diagram(s).
Diagrams The schematic package supplement for this manual contains schematic diagrams with component locations, active component type numbers, and electrical values.
Troubleshooting Techniques
A WARNING A
To avoid electrical shock, turn off the game power before attempting to troubleshoot this game. APB
Visual Check
Visually check for obvious problems in the portion of the game where the trouble is suspected. For example, check for loose or defective solder connections, integrated circuits loose in their sockets, loose cable connections, broken wires, and damaged PCBs or components.
Check Individual Components
Check soldered-in passive components (¢.g., resistors, capacitors, diodes) by disconnecting one end to isolate the measurement from the effects of the surrounding circuitry. Often, direct substitution is the most practical way to determine if a component is faulty. However, eliminate the possibility of some other circuit problem that could damage the substitute component.
Repair the Assembly
The following troubleshooting steps are arranged in a sequence recommended for locating a defective component. The procedure begins with a check of the simple trouble possibilities and progresses to more extensive procedures for localizing the problem to an assembly or major circuit, and then to a defective component.
Check Fuses
Check for open fuses. Refer to the power supply parts list in Chapter 5 and to the display manual for the location and rating of each fuse used in this game. Make sure that replacement fuses are the proper type and rating.
Check Power-Supply Voltages Improper operation of all circuits usually indicates a power supply problem. Be sure that the proper line voltage is available to the power supply. Refer to the label on the power supply for its voltage rating.
Localize Trouble
Determine the trouble symptom. Use the wiring diagrams in the schematic package supplement to determine which assemblies or major circuits could cause the trouble. Perform the self-test procedure provided in Chapter 2 of this manual. Repair or replace the defective part. Refer to Chapter 3 and information in this chapter for special removal and replacement procedures. Check for proper operation of the repaired circuit.
Soldering Techniques
Observe the following recommendations when removing or replacing components soldered to a PCB. Poor soldering practices can damage a PCB or heat-sensitive electrical components.
Choosing the proper soldering iron is essential before attempting to remove or replace soldered-in components. Excessive heat is a common cause of damage to a component or PCB. However, transient voltages from solder guns or improperly grounded soldering irons can also damage certain voltage-sensitive semiconductor devices. Refer to Troubleshooting Static-Sensitive Devices for more specific information.
A 15-to27-watt pencil-tip soldering iron is recommended to avoid separating the etched circuit wiring from the board material and to avoid damaging active components, A temperature-controlled soldering station rated at 700°F with a fine cone or a very fine chisel tip can also be used.
APB
The following additional equipment is recommended for removing and replacing soldered-in components:
- Solder Sucker—Hand-operated vacuum tool used to remove liquified solder from the PCB. We recommend the top-of-the-line Soldapullt® brand. Solder Wick—Resin-soaked copper braid used for removing excess solder from the lead connections on the PCB. See Removing Integrated Circuits for precautions relating to the use of a solder wick on a multilayer PCB with plated-through holes. © Flux Remover—Non-corrosive chemical used to clean foreign material from the PCB before soldering and to remove any flux residue where components have been replaced. Also used to clean any foreign material from the PCB during preventive maintenance. Isopropyl alcohol is recommended. © Acid Brush—Smull stiff-bristled paint or toothbrush used with flux remover to clean flux and other foreign material from the PCB.
Removing Integrated Circuits The easiest and safest method for removing soldered-in integrated circuits (IC) from a PCB is to cut off each pin as close to the IC case as possible with a tip dyke (diagonal cutter) as shown in Figure 4-1. Use the proper soldering iron as previously described under Soldering Techniques. Then, to avoid excessive heat buildup in one area of the PCB, apply heat directly toeach pin ina random order. Remove the loosened pin with the tip of the soldering iron or a needle-nose pliers as shown in Figure 4-2. Allow a moment for the PCB to cool before Proceeding to the next pin. Apply just enough heat to remove any stubborn pins.
Diagonal Cutter
Figure 4-1 Removing IC (Cut-Pin Method) Troubleshooting
} Needle-Nose Pliers
Soldering fron
Figure 4-2 Removing IC Pins
For a multi-layer PCB with plated-through holes, use a solder sucker to remove the remaining solder from inside each hole as shown in Figure 4-3. If possible, suck the solder from the opposite side of the PCB from where the heat is applied. Use a solder wick to remove excess solder from around the lead connection pads on the top and/or bottom surface of the PCB as shown in Figure 4-4.
Use an integrated-circuit (IC) pulling tool to remove socketed ICs. Do not pry up on one end of the ICs, because the pins could be bent or broken.
Troubleshooting Static-
Troubleshooting Static Sensitive Devices
Certain precautions must be taken when working with Static-sensitive devices, e.g., microprocessors, field-effect transistors (FET), complementary metal-oxide semiconductors (CMOS), and other large-scale integration (LSI) devices that use metal-oxide semiconductor (MOS) technology. Static charge buildup in a person’s body or leakage from an improperly grounded soldering iron can cause static-sensitive device failure.
Before handling a static-sensitive device or a PCB with such devices attached to it, ground any static voltage that may have accumulated in your body by touching an object that has been earth grounded. A bare wire wrapped around your wrist and attached to an earth ground is effective when working extensively with static-sensitive de-
‘Troubleshooting
Solder Sucker
Preferred Method APB
Soldering tron Solder Sucker |
Soldering Iron
Alternate Method
Figure 4-3, Removing Solder from Plated-Through Holes
Solder i
—— Solder Wick
Figure 4-4 Removing Solder from Lead Connection Pads vices. When soldering a static-sensitive device, use a soldering iron with a properly grounded three-wire cord. (Refer to Soldering Techniques for a discussion of recommended soldering irons and procedures.) Astatic-sensitive device can appear defective due to leakage on a PCB. Observe the precautions for grounding static voltages described in the preceding paragraph and clean both sides of the PCB with flux remover of an eraser before replacing what can be a good static-sensitive device. For discrete FETs, clean thoroughly between the gate, drain, and source leads. Static-sensitive devices can be packaged in conductive foam or have a protective shorting wire attached to the pins, Remove the conductive foam just prior to inserting the device into its socket or soldering it toa PCB. Remove the shorting wire only after the device is inserted into its socket or after all the leads are soldered in place.
~ee
“mee Chapter 5
Illustrated Parts Lists
This chapter provides information you need to order parts for your game. Common hardware (screws, nuts, washers, etc.) has been deleted from most of the parts lists. The PCB parts lists are arranged in alphabetical order by component. Each component subsection is arranged alphanumerically by reference designator. Other parts lists are arranged alphanumerically by Atari part number. In these parts lists, all A-prefix numbers come first. Following these are numbers in sequence evaluated up to the hyphen, namely 00- through 99-, then 000598- through approximately 201000., When ordering parts, please give the part number, part name, number of this manual, and serial number of your game. This will help us fill your order rapidly and correctly. We hope the results will be less downtime and more profit from your game. Atari Customer Service numbers are listed on the inside front cover of this manual.
Ilustrated Parts Lists APB
Items Not Shown: 78-6900402 Ya-Inch Foam Tape 178056-002 Ye-Inch Foam Tape
044343-01 Attraction Decal with Graphics A044357-01 044348-01 " Ps Lightboard Assy 044352-01 Attraction Shield 'A044419-01
Speaker Cover Grille i Light Harness Assy 179239-001 044346-01 Display Bezel with Graphics Light Receptacle 170002-001 139017-003 a Wells-Gardner Display Display Shield 040936-01 Molding
148007-104, or 148007-003 ‘Speaker
178013-001 Spring Draw Latch 171078-002 Coin Counter Steering Wheel Assy ‘See Figure 5-3
Control Panel Assy See Figure 5-2
Adjustable Giide
044955-01 038091-01 Seat Frame Weldment Coin Bax .
Foot Pedal Assy 1178195-002 See Figure 55 Small Adjustable Glide ees 044772-01 Seat Rail Opening Cover
Figure 5-1 Cabinet-Mounted Assemblies A044340-01 C
5-2
APB Iilustrated Parts Lists
A043372-01 Speaker Harness Assy
044518-01 Ground Plane 034536-02 Vibration Damper CPU PCB Assy See Figure 5-8
A044414-01 Main Harness Assy
044373-01 Rear Door Panel
044376-01 Component Cover Shield
A044415-01 Gasaeot fen Assy EMI Cover Video PCB Assy (behind EMI cover) sta ee See Figure 5-9 Seat Rail Bracket
Power Supply Assy: See Figure 5-4 ——-£, A044516-01 4 Filter Board Assy Ca , 171002.008, o A044416-01 Gabe Assy 171002-001 Video Harness Assy Fan A043050-01 A043617-01 FanCord Assy ONOM Switch Assy with Harness }78093-00" 009992-01 in Guard On/Off Switch Cover
Figure 5-1 Cabinet-Mounted Assemblies, Continued A044340-01 C
Illustrated Parts Lists
Cabinet-Mounted Assemblies Parts List
Part No. Description
A043050-01 On/Off Switch Assembly with Harness A043372-01 Speaker Harness Assembly A043617-01 Fan Cord Assembly A044350-01 Seat Assembly A044357-01 Lightboard Assembly A044358-01 Cabinet Assembly A044414-01 Main Harness Assembly A044415-01 AC Harness Assembly A044416-01 Video Harness Assembiy A044516-01 Filter Board Assembly 78-3201 Adjustable Glide 78-6900402 %-Inch x ¥-Inch Thick Foam Tape (24 inches required; used on front edge of control panel facing display shield) 009992-01 On/Off Switch Cover 034536-02 ¥Ya-Inch Thick Vibration Damper 037332-01 Louvered Grille 038091-01 Coin Box 043148-01 EMI Cover 044343-01 Attraction Decal with Graphics 044346-01 Display Bezel with Graphics 044347-01 Display Shield 044348-01 Attraction Shield 044352-01 Speaker Cover Grille 044354-01 Seat Rail Bracket 044355-01 Seat Frame Weldment 044373-01 Rear Door Panel 044376-01 Component Cover Shield 044518-01 Ground Plane 044772-01 Seat Rail Opening Cover 139017-003 ‘Wells-Gardner 19-Inch Medium-Resolution Color Raster Display, Model 19K7915 148007-104 4%-Inch, 8 Q, 10 W, Shielded Speaker (Acceptable substitute is part no. 148007-003) 170002-001 60 W 120 V Soft White Bulb 171002-003 110 V, 110 CFM Exhaust Fan (Acceptable substitute is 110 V, 70 CFM Exhaust Fan, part no. 171002-001) 171078-002 12 VDC Non-Resettable Coin Counter 178013-001 Spring Draw Latch 178056-002 Y-Inch x ¥-Inch Thick Foam Tape (4 inches required; two inches used underneath each side of bezel) 178093-001 Fan Guard 178195-002 #14-20 x 1-Inch Long Adjustable Glide (on underside corners of seat frame) The following are technical information supplements for this game: T™M-308 APB Operators Manual SP-308 APB Schematic Package ST308 APB Self-Test Label TM-297 Wells-Gardner Model 19K7915 Video Display Service Manual
APB Hlustrated Parts Lists
Steering Wheel Assy ‘See Figure 5-3 Items Not Shown: 043563-01 78-6900402 Spacer Foam Tape 043463-01 75-9910NO 178084-007 Bow Washer Stamped Nut Cable Tie 85-23F112 178030-004 Screw, Red Button Assy 178030-007 160013-002 Yellow Button Assy _ Cross-Bar Leaf Switch with Button 160013-001 Holder Leat Switch with Button Holder
044341-01 Control Panel
044349-01 Controi Panet Decal
75-010x Screw A044417-01 Harness Assy
Figure 5-2 Control Panel Assembly A044342-01 A
Control Panel Assembly Parts List
Part No. Description
A000598-10 Steering Wheel Assembly 4044417-01 Control Harness Assembly 75-010x #10 Flat Washer 75-9910NO #11 %-Inch Stamped Nut 85-23F112 #10%-Inch Type F Hex Washer-Head Screw 043463-01 Bow Washer 043563-01 Plastic Spacer 0443.41.01 Control Panel 044349-01 Control Panel Decal 1609013-001 Leaf Switch with Button Holder 160013-002 Cross-Bat Leaf Switch with Button Holder 178030-004 Red Button Assembly 178030-007 Yellow Button Assembly 178084-007 ‘Twist-Lock Cable Tie
Illustrated Parts Lists
78-40104 72-0398 Steering Wheel Lock Washer
175005-004 Flat Washer 000599-02 Logo Cover
043788-01 = Shatt 72-5416X te 5 \ Bott
72-8512! Screw 76-092020 Thompson Bearing
000605-01 75-055 Lock Washi He ° 76-091010 oaengs Thompson Bearing
72-5512 Bol A035220-02 N\ eR Coupler PCB Assy 85-22F 206 000616-01 Seren 75-07002 Encoder Hub ‘Washer
Figure 5-3 Steering Wheel Assembly A000598-10 AC
APB Illustrated Parts Lists
Steering Wheel Assembly Parts List
Part No. Description
A035220-02 Coupler PCB Assembly 72-0398 %-Inch External Steel/Zinc Lock Washet 72-5416X %-16 x 1-Inch Steel/Zinc Hex-Head Bolt 72-5512 Y%-20 x %4-Inch Steel/Zinc Hex-Head Bolt
72-8512 14-20 x %4-Inch Socket Head Cap Screw 75-0128 #2 Flat Plain Washer 75-055 ¥4-Inch Internal Tooth Lock Washer 75-07002 ¥4-Inch Special Flat Washer 76-091010 ‘Type-10L10-FK Thompson Bearing 76-092020 Type-20L20-FK Thompson Bearing 78-40104 10-Inch Steering Wheel 85-22F206 #2-56 x ¥-Inch Cross-Recessed Pan-Head Machine Screw 000599-02, Atari Logo Cover 000605-01 Housing 000616-01 Encoder Hub 043788-01 Shaft 107027-001 Multi-Use Lithium-Base Lubricant 175005-004 406 LD., 1.25 O.D., 16-Gauge Thick Steel/Zinc Flat Washer
5-7
Illustrated Parts Lists APB
A WARNING A This 5-volt switching power supply may not have a shield as illustrated below. The power supply has high voltages on it when power is turned on. Therefore, be sure you do not touch this power supply unless you have tured off the power to the game.
149008-001 Hitron 5V Switching Power Supply Sub-Assy A043367-02 Black Jumper Assy 179231-002 A043367-03 Terminal Block White Jumper Assy
A043367-01 Jumper Assy A043909-01 5V Harness Assy
178120-112 PCB Spacer A044395-01 Triac Controller PCB
043396-01 Power Supply Chassis Base
043622-01 Fuse Label 46-2012002 2 Amp Fuse
Figure 5-4 Switching/Linear (SL) Power Supply Assembly A044547-01 A
5-8
APB Illustrated Parts Lists
Switching/Linear (SL) Power Supply Assembly Paris List
Part No. Description
A042384-01 Line Filter Assembly A043367-01 Jumper Assembly A043367-02 GInch, Black Jumper Assembly 4043367-03 6-Inch, White Jumper Assembly A043909-01 5 V Harness Assembly A044395-01 Triac Controller PCB 46-2012002 250 V Slow-Blow 2 A Fuse 46-2013002 250 V Slow-Blow 3 A Fuse
72-HA4606S #6-32 x ¥Inch Cross-Recessed Pan-Head Thread-Forming Screw 72-HA4806S #8-32 x ¥-Inch Cross-Recessed Pan-Head Thread-Forming Screw 034544.01 Fuse Block Cover 037640-01 Power Supply Warning Label 043396-01 Power Supply Chassis Base 043622-01 Power Supply Fuse Label 142042-001 ‘Transformer 149006-001 Hitron 5 V 13 A Switching Power Supply Sub-Assembly; sce below.
178120-112 34-Inch PCB Spacer 179225-2205 5-Position Fuse Block (Acceptable substitute is part no. 79-3206) 179231-002 2-Position Terminal Block
Hitron 5-Volt Power Supply Sub-Assembly Parts List
| Designator | Description | Part No. |
Capacitors
| cl | Capacitor, Metal Film, 0.047 pF, 250 V | 99-211036 |
| C2 | Capacitor, Metal Film, 0,1 pF, 400 V | 99-211038 |
| C3, C4 | Capacitor, Ceramic, 4700 wE, 400 V | 99-211049 |
| C5, C6 | Capacitor, Electrolytic, 100 uF, 200 V | 99-211046 |
| C7 | Capacitor, Metal Film, 0.1 ¢F, 400 V | 99-211038 |
| C8 | Capacitor, Ceramic, 0.001 pF, 2 kV | 99-211042 |
| Cc | Capacitor, Ceramic, 0.01 F, 1 kV, Z5U | 99-211041 |
| C10 | Capacitor, Flectrolytic, 220 zE, 25 V | 99-211045 |
| cu | Capacitor, Metal Film, 0.22 4B 100 V | 99-211037 |
| C12 | Capacitor, Metal Film, 0.022 uF, 100 V | 99-211039 |
| C13 | Capacitor, Metal Film, 0.22 uF, 100 V | 99-211037 |
| C14 | Capacitor, Ceramic, i800 PF, 2 kV, Z5V | 99-211040 |
| Ci5-C18 | Capacitor, Electrolytic, 2200 pF, 16 V | 99-211069 |
| cio | Capacitor, Ceramic, 470 PE, 1 kV, Z5P | 99-211043, |
| C20 | Capacitor, Electrolytic, 2200 yF, 16 V | 99-211069 |
| C21 | Capacitor, Ceramic, 220 pF, 25 V | 99-211070 |
Diodes
| D1, D2 | Diode, Fast Recovery, RPG10K | 99-211064 |
| D3. | Diode, Fast Recovery, RPG15B | 99-211011 |
| D4 | Diode, Fast Recovery, RPG10B | 99-211009 |
| DS-D7 | Diode, Switching, 1N4148 | 99-211012 |
Illustrated Parts Lists APB
Hitron 5-Volt Power Supply Sub-Assembly Parts List, Continued
| Designator | Description | Part No. |
| D8, DO | Diode, Schottky, $15SC4M | 99-211064 |
| D11,D12 | Diode, Schottky, S10SC4M | 99-211005 |
| D13-D16 | Diode, Rectifier, 1N4006 | 99-211008 |
Inductors
| Ll | Inductor, 15 mH | 99-211052 |
| L2 | Inductor, 9.8 #H | 99-211071 |
| L6, L7 | Inductor, 7 #H (Acceptable substitute is part no. 99-211051) | 99-211050 |
| L4 | Inductor, 2.2 wH | 99-211054 |
| LS | Inductor, 1.5 mH | 99-211053 |
Resistors
| R1, R2 | Resistor, Carbon Film, 180 kQ, +5%, 1 W | 99-211034 |
| R3 | Resistor, Wirewound, 1200, +5%,2W | 99-211019 |
| R4 | Resistor, Wirewound, 0.472, +5%,2W | 99-211018 |
| RS | Resistor, Wirewound, 270, +5%,2W | 99-211065 |
| RO, R7 | Resistor, Carbon Film, 5.69, +5%, 4 W | 99-211027 |
| R8 | Resistor, Wirewound, 0.479, +5%, 2 W. | 99-211018 |
| RO | Resistor, Carbon Film, 100, +5%, 4 W | 99-211029 |
| R10 | Resistor, Carbon Film, 1 kQ, +5%, 4 W | 99-211032 |
| R11 | Resistor, Carbon Film, 472, +5%, %« W | 99-211625 |
| R12 | Resistor, Carbon Film, 5.692, +5%, 4 W | 99-211027 |
| R13 | Resistor, Carbon Film, 3302, +5%, 4 W | 99-211026 |
| R14 | Resistor, Carbon Film, 270Q, +5%, 4 W | 99-211023 |
| R15 | Resistor, Carbon Film, 3300, +5%, % W | 99-211022 |
| R16 | Resistor, Carbon Film, 8.29, +5%, 4% W | 99-211028 |
| R17, R18 | Resistor, Carbon Film, 562, +5%, 4 W | 99-211031 |
| RID | Resistor, Carbon Film, 390, +5%, %4 W | 99-211030 |
| R20 | Resistor, Carbon Film, 2k®, +5%, 4 W | 99-211035 |
| R21 | Resistor, Carbon Film, 470 9, +5%, 4 W | 99-211024 |
| R22 | Resistor, 2.2kQ, +2%, 4 W | 99-211021 |
| R23 | Resistor, Metal Film, 2 k®, + 2%, 4 W | 99-211033 |
| R25 | Resistor, Carbon Film, 100, +5%, 4 W | 99-211029 |
| R26 | Resistor, Carbon Film, 6.80, +5%, % W | 99-211066 |
| R27 | Resistor, Carbon Film, 129, +5%, 4 W | 99-211067 |
| R28 | Resistor, Carbon Film, 2.40, +5%, 2 W | 99-211068 |
| R31 | Resistor, Wirewound, 1500, +5%,2 W. | 99-211016 |
‘Transistors
| Ql | Transistor, NPN, 2SD725 | 99-211062 |
| Q2 | Transistor, NPN, PE8050B | 99-211003, |
| 3 | Transistor, PNP, PE8550B | 99-211063 |
Miscellaneous
| Fl | Fuse, 2 A, 125 V, Semko | 99-211058 |
| IC1 | Regulator, UA43 AWC | 99-211061 |
| SCR1 | Thyristor, SCR | 99-211013 |
| TL | Transformer | 99-211055 |
| 72 | ‘Transformer | 99-211075 |
| TRI | Thermistor, 0.50, +5%,5 W | 99-211020 |
| VRI | Potentiometer, Trimming, 3 kQ | 99-211014 |
| ZD1 | Diode, Zener, 1N752A. | 99-211007 |
Fuse, 2 A, 250 V 99-211056 Fuse Holder 99-211060 Terminal Block, 8 Ckt. 99-211057 Heat Sink 99-211059 Heat Sink, 1.5 mm 99-211061
5-10
APB Illustrated Parts Lists
N O T E S
5-11
Illustrated Parts Lists APB
043524-01 043529-01 Foot Pedal Foot Pedal Safety Tread
043691-01 Pedal Return Spring
19-9026 Potentiometer <
72-8808 Screw
75-9188, Nut
043525-01 Pedal Frame
A043620-01 Foot Pedal Cable Assy
043526-01 Foot Pedal Link
043523-01 Foot Pedal Shaft A, 178065-100 Wire and Cable Tie 76-080802 (not shown) Bearing
178012-006 Retaining Ring
Figure 5-5 Foot Pedal Assembly A043527-01 B
5-12
APB Ilustrated Parts Lists
Foot Pedal Assembly Parts List
Part No. Description
A043620-01 Foot Pedal Cable Assembly 19-9026 5 k@ Potentiometer with Hex Nut and Lock Washer 72-8808 #8-32 x 2 Inch Hex Socket-Head Cap Screw 75-9188 #8-32 Steel Cadmium Hex Machine Nut
76-080802 ¥e-Inch LD. x inch Bearing (Nyliner) 043523-01 Foot Pedal Shaft 043524-01 Foot Pedal 043525-01 Pedal Frame
043526-01 Foot Pedal Link 043529-01 Foot Pedal Safety Tread. 043691-01 Pedal Return Spring 107027-001 Multi-Use Lithium-Base Lubricant 178012-006 Y-Inch Diagonal Shaft Retaining Ring 178065-i00 4-Inch Loose Wire and Cable Tic
5-13
Wlustrated Parts Lists APB
99-10148 Lock Assembly
99-10142 Button Housing
72-HA1404C Screw
99-10134 99-10119 Cover 99-10139 > K/\ )~———— ButtonAssembly | gou01s Coin Door a ‘ Button
a 99-10115 99-10148 Spring Lock Assembly
99-10141 Coin Return Cover
S & ‘ a 99-10117 Coin Return Door
72-JA1405B Screw I~—— 99-10144 Channel Clip
99-15066 Screw
99-10149 Service Door
038091-01 Coin Box
99-10143 Frame
Figure 5-6 Coin Acceptors, Inc. Coin Door Assembly 171027-001 A
5-14
APB Illustrated Parts Lists
99-10140 Panel Assembly 75-9488 Locknut a
99-10152 DRE Right Coin Inlet
171006-035 Coin Mechanism 99-10116 Lever
99-10147 Harness
75-9448 Locknut
99-0096 Fastener
99-10151 Left Coin Inlet
70-11-47 Lamp
99-1080 Lamp Socket
99-10105 72-9406S Bar Screw
99-10104 Bar Retainer
99-10042 thru 99-1045 99-10154 Coin Switch Assembly Bracket Assembly
99-10153 ix Coin Return Box oN 99-10150 Switch Cover
Coin Chute 65-441C Coin Switch
99-1075 thru 99-10078 ~ Switch Wires 99-10008 Retainer 75-14128 Screw
Figure 5-6 Coin Acceptors, Inc. Coin Door Assembly, Continued 171027-001 A
5-15
Illustrated Parts Lists APB
Coin Acceptors, Inc. Coin Door Assembly Parts List
Part No. Description
65-441C Coin Switch 70-11-47 Miniature Bayonet Lamp 72-94068 #4-40 x ¥-Inch Truss-Head Screw 72-HA1404C #4-40 x Y-Inch Pan-Head Screw
72-JA1405B #4-40 x 0.31-Inch Pan-Head Screw 75-14128 #4-40 x ¥%-Inch Pan-Head Screw 75-9948 #4-40 Locknut 99-10008 Retainer
99-10042 Coin Switch Assembly for Belgian 5 Fr and U.S. 25¢ 99-10043 Coin Switch Assembly for German 1 DM, Japanese 100 Yen, Swiss 1 Fr 99-10044 Coin Switch Assembly for German 2 DM, Italian 100 L, U.S. $1.00 99-10045 Coin Switch Assembly for Australian $.20, German 5 DM, British 10 P
99-10068 Coin Return Chute
| 99-10075 | Switch Wire | (included in coin switch assembly 99-10043) |
| 99-10076 | Switch Wire | (included in coin switch assembly 99-10042) |
| 99-10077 | Switch Wire | (included in coin switch assembly 99-10044) |
| 99-10078 | Switch Wire | (included in coin switch assembly 99-10045) |
99-10080 Lamp Socket 99-10081 Key Holder 99-10096 Fastener
99-10104 Bar Retainer 99-10105, Bar 99-10115 Spring 99-10116 Plastic Coin Return Lever
99-10117 Steel Coin Return Door 99-10118 Amber Coin Return Button. 99-10119 Amber Coin Button for U.S. 25¢ 99-10134 Coin Button Cover
99-10139 Coin Door 99-10140 Coin Door Inner-Panel Assembly 99-10141 Die-Cast Coin Return Cover 99-10142 Die-Cast Button Housing
99-10143, Coin Door Frame 99-10144 Channel Clip 99-10147 Harness 99-10148 Lock Assembly
99-10149 Service Door 99-10150 Switch Cover 99-10151 Left Coin Inlet 99-10152 Right Coin Inlet
99-10153 Coin Return Box 99-10154 Bracket Assembly 99-15066 Screw for Clamp 171006-035 Metal Coin Mechanism for U.S. 25¢
5-16
APB Iustcated Paits Lists
CPU PCB Assy See Figure 5-8 044518-01 Ground Plane
178181-6802 : 034536-02 Spacer : : Yetnch Foam Damper
Video PCB Assy See Figure 5:9
176031-2616 Thumb Screw
177018-206 Thumb Nut
Ve-Inch Foam Damper
043148-01 EMI Cover NOTE To comply with emission requirements, the Federal Communications Commission requires that the Video PCB Assembly be housed in the EMI cover. Do not operate this game without properly installing the EMI cover, metal spacers, and thumb nuts. Also, do not operate this game without the Filter Board Assembly installed at the bottom of the Video PCB.
Figure 5-7 PCB Mounting Hardware
PCB Mounting Hardware Parts List
Part No. Description
A044519-01 Video PCB Assembly A044520-01 CPU PCB Assembly 034536-02 ¥e-Inch Foam Vibration Damper 043 148-01 EMI Cover
044518-01 Ground Plane 176015-112 10 x 34-Inch Cross-Recessed Pan-Head Deep-Thread Screw 17603 1-2616 #6-32 x %-Inch Knurled Thumb Screw 177018-206 #632 Knurled Thumb Nut 178181-6802 250 O.Dx.171 LD. x .125-Long Round Spacer
Illustrated Parts Lists
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specie written permission of Atari Games Corporation, Milpitas, CA. This drawing is only Conditionally issued, and neither receis nor possession ihereo confers or transfers any right in, or icerse to use, the subject matter of he drawing fr any design oF technical information shown thereon, nor any right to reproduce this drawing or any part thereot. Excent for manufacture by vendors of Alari Games Corporation, and for manutacture under the corporation's written fcense, no right is granted to reproduce this drawing Or the subject matter thereof, unless by writen agreerment with or wten permission from the corporation,
e116
1ag054-1194 rr
| t | i | toe | ' | — | tht | : |
f [ t I oe Lezuy II Lsa74 ce 196051-1135 ts 136051-1136 Lsow J1o2 cos eer S74 4 cao J teise a soo ro eee, Tere Boca i Had seo Rs may NE seo w q a _ i Boa al “R (
| As | ceB | FF | Fog | k | LO | Sal | ae | [| |
s ye . an = tet
soit) Se Petpet
| = | i | ‘a | Ene | bg | 7 | staat | 3 |
OER itn ates EPe
| Senge | eee | : | |||
| ' | g | Bai | a | 5 | |
| (fall | () | (Jal) | age | pt | i |
= f ‘ pf esd
| bs | Jaz | J44 | foe 1h Usa | ° |
Figure 5-8 APB Central Processing Unit (CPU) PCB Assembly A044520-01 A APB.
APB Illustrated Parts Lists
APB Central Processing Unit (CPU) PCB Assembly Parts List
Desig- Desig-
| nator | Description | Part No. | nator | Description | Part No. | |
| Integrated Circuits | 5D | Integrated Circuit, Type-7418245 | 37-74L8245 | |||
| 1A | Integrated Circuit, Type-6116 | 137211-001 | 3E | Integrated Circuit, Type-7418374 | 37-74L8374 | |
| IBIC | Integrated Circuit, Type-6i16 | 137211-001 | _ | . | ||
| 1D | Integrated Circuit, Type-2804-3 | 137329-300 | SF | Integrated Circuit, Type-74LS175, | 37-74LS8175 | |
| EEPROM | SH | Integrated Circuit, ‘Type-74L8245 | 37-74LS245 | |||
| IE | Integrated Circuit, Type-74LS32 | 37-7432 | 5] | Integrated Circuit, Type-74LS08 | 37-741808 | |
| 5K | Integrated Circuit, | Type-741804 | 7-TALSO4 | |||
| y | Integrated Circuit, Type-7418245 | 37-74L8245, | grated | Circlt, | Type | 3 |
| IK | Integrated Circuit, Type-7418245 | 37-7408245 | 3L | Integrated Circuit, Type-74L$139 | 37-7418139 | |
| IL | Integrated Circuit, Type-74L$32 | 37-741832 | 5M | Integrated Circuit, Type-7418373 | 37-7ALS373, | |
| iM | Integrated Circuit, Type-74L8244 | 37-74LS244 | 5N | Integeated Circuit, Type-74L$174 | 37-74LS174 | |
| IN | Integrated Circuit, Type-7418244 | 37-74L8244 | ap | Tniepiated Citeult, ype 7418248 | TETALSPAG | |
| IP | Integrated Circuit, Type-74L8244 | 37-74LS244 | CB | Integrated Circuit, POKEY | €012294-01 | |
| IR | Integrated Circuit, Type-74832 | 37-74832 | oD | Integrated Circuit, Type-74L245 | 37-T4LS245 | |
| Is | Integrated Circuit, Type-ADC0809 | 137243-001 | oe | Integrated Circuit, Type-741$374 | 37-7418374 | |
| 2A | Integrated Circuit, EPROM, | 136051-x134 | OF | Integrated Circuit, EPROM, | 136051-x128 |
‘Type-27512, 200 ns ‘Type-27512, 200 ns
| 26 | Bisa rail EPROM, | 36051-2155, | 4 | Integrated Circuit, EPROM, | 136051-x130 |
Yype-27512, 200 ns B7512, 200
| 2c1D | Integrated Circuit, EPROM, | 136051-x136 | Type-27512, | 200 ns | |
| Fype-27512, 200 ns | o | Integrated Circuit, EPROM, | 13605 1-3132 | ||
| 2R | Integrated Circuit, Type-7418244 | 37- 7418244 | Type27512, 200 ns | ; | |
| ON | Integrated Circuit, EPROM, | 136051-x129 | |||
| a | Integrated Circuit, | 137361-002 | ‘Type-27512, 200 ns | ||
| ‘Type DCTALXA) | oP | Integrated Circuit, EPROM, | 136051-x131 | ||
| 2 | Integrated Circuit, Type 74LS174 | 37-74LS174 | Type 27512, 200 ns | ||
| 2M | Integrated Circuit, Type-741574 | 37-741874 | |||
| 2N | Integrated Circuit, Type-7418670 | 37-74L8670 | 68 | Integrated Circuit, EPROM, | 136051-x133 |
1627512, 200 ns
| sa | ase oa eats | Bahco | 7B | ieprated Circuit, POKEY | C012294-01 | |||||
| E | integrated | Circuit, | Type-74LS | 7 | I | I | ed | Ci | TM$522 | 73084 |
| 3F | Integrated Circuit, Type74LS161 | 37-741 S161 | kg | Geaed chal Lee” | ROO | |||||
| 3H | Integrated Circuit, Type-74LS00 | 37-741800 | J | |||||||
| a1 | Integrated Circuit, Type-74L8139 | 37-7415139 | ie | tntegated Great, Hoe yaist0 | 3aatsio | |||||
| 3K | Integrated Circuit, Type-7418393 | 37-7418393 | Seed | Chit | Roegi le | : | ||||
| 3L | Integrated Circuit, Type-74874 | 3774874 | m™ | Tnnepraiea Ditc, e | el | |||||
| 3M | Integrated Circuit, Type-74L8138 | 137177-001 | aL | esos ib mot | cued | |||||
| 3N | Integrated Circuit, Type-74LS74 | 37-F4L874 | . | |||||||
| 3P | Integrated Circuit, Type-74874 | 37-74874 | 7N | Integrated Circuit, EPROM, | 136051-x127 | |||||
| 3R | Integrated Circuit, Type-74LS20 | 37-74L820 | Type-27128, 300 ns | |||||||
| 4A | Integrated Circuit, Type-74LS244 | 37-T4LS244 | 7 | Integrated Ciccuit, Type-6116 | 137211-001 | |||||
| TR | Integrated Circuit, Type-74L8161 | 37-74LS161 | ||||||||
| 4B | Integrated Circuit, Type-7415244 | 37-7AL8244 | 8B | Integrated Circuit, Type-74LS161 | 37-74LS161 | |||||
| 4BIC | Integrated Circuit, Type-74L5139 | 37-748 139 | ||||||||
| 40D | Integrated Circuit, Type-74L874 | 37-741874 | 8c | Integrated Circuit, Type-7415273 | 37-74L8273 | |||||
| 4D | Integrated Circuit, Type-7415163A | 37-74LS163A | 8D | Integrated Circuit, Type-74LS273 | 37-7ALS273 | |||||
| ; | SF | Integrated Circuit, Type-74L8244 | 37-74L8244 | |||||||
| 48 | Integrated Ciccuit, Type-74L8138 | 137177-001 | ‘cai | : | : | |||||
| 4F | Integrated Circuit, Type-741$393 | 37-74L8393 | Bug | Integrated Circuit, Type-¥2151 | 137401-001 | |||||
| 4H | Integrated Circuit, Type-74L874 | 37-741S74 | 8K | Integrated Circuit, Type-YM3012 | 137402-001 | |||||
| 4 | Integrated Circuit, Type-74L874 | 37-74LS74 | 8N | Jntegrated Cireuit, Type-74804 | 37-74804 | |||||
| soe | 4 | 9B | Integrated Circuit, ‘Type-LF13201 | 137352-001 | ||||||
| 4K | Integrated Circutt, Type-74L$373 | 37-74L8373 | : | 7 | ||||||
| 4 | Integrated Circuit, Type-74L8138 | 137177-001 | a | Integrated Circuit, TypeLF13201 | 137352-001 | |||||
| 4M | Integrated Circuit, SLAPSTIC | 137412-107 | oD | Inte | «cuit | Tene | ||||
| 7 | sgrated Circuit, Type-LF13201 | 137352-001 | ||||||||
| 4N | Integrated Circuit, Type-74L8245 | 37-7418245 | 9DIE | Integrated Circuit, Type-LF13201 | 137352-001 | |||||
| 4P | Integrated Circuit, Type-74L5244 | 37-7ALS244 | OTK | Integrated Circuit, Type-1M324 | 37-LM324 | |||||
| 5B | Integrated Circuit, Type-6502A | 90-6013 | SLM | Integrated Circuit, Type-LM324 | 37-LM324 |
“Sc” in the part number denotes the revision level 5-19
Illustrated Parts Lists APB
APB Central Processing Unit (CPU) PCB Assembly Parts List, Continued Desig- Desig-
| nator | Description | Part No. | nator | Description | Part No. |
| 10B | Integrated Circuit, Type-LM324 | 37-1M324 | 122 | Capacitor, Ceramic, .22 wR, 25 V | 122004-224 |
| 10C | Integrated Circuit, Type-LM324 | 37-1M324 | 123 | Capacitor, Ceramic, .22 wE 25 V | 122004-224 |
| 10F | Integrated Circuit, Type-LM324 | 37-1M324 | ; | ||
| 10LIM | Integrated Circuit, Type-TLO82CP | 37-TLO82CP | 124 | Capacitor, Mica, 470 pE, 100 V | 128002471 |
| uM | Integrated Circuit, Type-74C04 | 137309-001 | 125 | Capacitor, Mica, 470 pF 100 V | 128002-471 |
| C126 | Capacitor, Ceramic, 22 wE 25 V | 122004-224 | |||
| Sockets | C127 | Capacitor, Ceramic, .22 uF, 25 V | 122004224 | ||
| 16-Pin Medium-Insertion-Force Socket | 79-42C16 | , | , | ||
| 20-Pin Medium-Insertion-Force Socket | 79-42C20 | ea | Cepeetoe Ceramic hve 20 | tz202-104 | |
| ee | : | Capacitor, Ceramic, .1 pF, 50 V | 122002-104 | ||
| 24-Pin Medium-nsertion-Force Socket | 79-42C24 | C133 | Capacitor, Ceramic. | 1 ul. 50V | 122002.104 |
| 28-Pin Medium-Insertion-Force Socket | 79-42C28 | C134 | Capa \citor, | Ceramic, .22 pE 25V | 122004-224 |
| 40-Pin Megium-Insertion-Force Socket | 79-42C40 | ° | — | ||
| capaci | C135 | Capacitor, Aluminum, 470 pF 25 V | 24-250477 | ||
| pacitors | 13 | Capacitor, Aluminum, 470 pF, 25 V | 24-250477 | ||
| C1-C60 | Capacitor, Ceramic, .1 aR 50 V | 122002-104 | 38 | Capacitor, Ceramic, .1 pF, 50 V | 122002-104 |
| €31-C60 | Capacitor, Ceramic, -i uF, 50 V | 122002-104 | c139 | Capacitor, Aluminum, 100 pF 35 V | 24-350107 |
| C61 | Capacitor, Ceramic, .018 4 50 V | 122015-183 | |||
| C62-C64 | Capacitor, Ceramic, .22 wR, 25 V | 122004-224 | ce | Capacitor, poe es 50V | 24-500105 |
| Capacitor, | Ceramic, .1 | wk, 50V | 122002-104 | ||
| C65 | Capacitor, Ceramic, .1 pF, 50 V | 122002-104 | C13 | Capacitor, Ceramic, .1 ¢F, 50V | 122002-104 |
| C66 | Capacitor, Ceramic, .1 wF, 50 V | 122002-104 | 144 | Capacitor, Ceramic, .0027 wl, 50 V | 122015-272 |
| C67 | Capacitor, Mica, 100 pF, 190 V | 128002-101 | ; | ||
| C68 | Capacitor, Mica, 39 pF, 100 V | 128002-390 | cas | Capacitor, Coram 0012 pF, 50V | 122015-122 |
| 4 | Capacitor, | Ceramic, .0039 | uF, 50 V | 122015-392 | |
| coo | Capacitor, Ceramic, .1 4B 50 V | 122002-104 | 147 | Capacitor, Ceramic, ‘0c8 A ov | 122015-682 |
| C70 | Capacitor, Mica, 39 pF, 100 V | 128002-390 | C148 | Capacitor, Ceramic, .1 pF, 50 V | 122002-104 |
| C71 | Capacitor, Mica, 100 pk, 100 V | 128002-101 | C149-C152. Capacitor, Ceramic, .1 uF, 50V | 122002-104 | |
| C72-C79 | Capacitor, Ceramic, .01 uF, 25 V | 122005-103 | |||
| , | , | Diodes | |||
| c80 | Capacitor, Ceramic, .001 uF, 50 V | 122002-102 | CRI-CR3 | Diode, Type-1N100 | 31-1N100 |
| cel | Capacitor, Ceramic, .001 aE, 50 V | 122002-102 | CRA | Diode, Type-1N4001 | 31-1N4001 |
| C82-C89 | Capacitor, Ceramic, .1 aR, 50 V | 122002-104 | CRS | Diode, The IN 4001 | 31-1N4001 |
| C90 | Capacitor, Ceramic, .22, 25 V | 122004-224 | CRE | Diode, Light Emitting, Type M5053. | 38MV5058 |
| oo | Capacitor, Tantalum, 10 wF, 20 V | 29-046 | chy | Diode, Type:INSOOL | SE INaOOL |
| C92 | Capacitor, Ceramic, 01 pk 25V | 122005-103 | Connectors and Fasteners | ||
| 093 | Capacitor, Mica, 220 pF, 100 V | — | ys | Connector, Header, 17-Circuit, | 179118.017 |
| 094 | Capacitor, Mica, 220 pF, 100 V | 128002-221 | ‘ioour | ° | ; |
| 95 | Capacitor, Ceramic, .0027 nF, 50 V | 122015-272 | J16 | Connector, Header, 5-Circuit, 100 ctr | 179118-005 |
| C96 | Capacitor, Tantalum, 10 pF, 20 V | 29-046 | J20 | Connector, Header, 9-Circuit, | 179014-009 |
| co7 | Capacitor, Ceramic, .0027 uF, 50 V | 122015-272 | 156 ctr, pol | — | |
| C98-C100 | Capacitor, Ceramic, .1 pF, 50 V | 122002-104 | J103 | Connector, Header, 11-Circuit, | 179118-011 |
. ctr
| C101 | Capacitor, Aluminum, 10 uF, 35 V | 24.350106 | —_ | ||
| 102 | Capacitor, Aluminum, 10 pF, 35 V | 24-350106 | J106 | Connector, Header, 11-Circuit, | 179118-011 |
| C103-C109 Capacitor, Ceramic, .1 E50 V | 122002-104 | 100 ctr | |||
| co | Capacitor, Ceramic, .01 pF, 25. V | 122005-103 | P18 | ao Card Edge, 80-Circuit | 179221-180 |
x2
| ci | Capacitor, Ceramic, 01 pF, 25 V | 122005-103 | Q1,Q2. | Fastener, Nylon, Snap-in | 81-4302 | |
| cui2 | Capacitor, Ceramic, .1 a, 50 V | 122002-104 | Q9,Q10 | Fastener, Nylon, Snap-in | 81-4302 | |
| C113 | Capacitor, Ceramic, .1 pF, 50 V | 122002-104 | ||||
| cis | Capacitor, Mica, 220 pF, 100 V | 128002-221 | RI | Feat pase | bk | Lon |
| ferminal, | fab | (Acceptable | 4 | |||
| C116 | Capacitor, Mica, 220 pF, 100 V | 128002-221 | substitute is part number 020670-01) | |||
| C17 | Capacitor, Ceramic, .01 pk 25.V | 122005-103 | ||||
| cus | Capacitor, Ceramic, .001 #E 50 V | 122002-102 | Inductors | |||
| cg | Capacitor, Ceramic, .001 pF, 50 V | 122002-102 | ul | Inductor, 33 aH | 141016-007 | |
| ; | ; | 12 | Inductor, 100 #H | 141002-001 | ||
| C120 | Capacitor, Ceramic, 01 pF, 25 V | 122005-103 | ||||
| 121 | Capacitor, Ceramic, .1 wR, 50V | 122002-104 |
5-20 “x” in the part number denotes the revision level
APB Mlustrated Parts Lists
APB Central Processing Unit (CPU) PCB Assembly Parts List, Continued. Desig- Desig:
| nator | Description | Part No. | nator | Description | Part No. | |
| ‘Transistors | Ri09 | Resistor, ‘4 W, 100KQ, +5% | 110000-104 | |||
| QU, Q2 | ‘Transistor, 2N6044 | 34.2N6044 | R110 | Resistor, 4 W, 3902, +5% | 110000-391 | |
| Q3,Q4 | Transistor, 2N3906 | 33-2N3906 | RU | Resistor, 4 W, 5609, +5% | 110000-561 | |
| Q5-Q8 | Transistor, 2N3904 | 34-2N3904 | R112 | Resistor, 4 W, IKQ, +5% | 110000-102 | |
| Q11,Q12 | Transistor, 2N3904 | 3423904 | RU3 | Resistor, % W,5.6KQ, +59% | 110000-562 | |
| Resistors | RI14 | Resistor, 4 W, 10K, +5% | 410000-103 | |||
| RI, R2 | Resistor, 4 W, 10K @, +5% | 110000-103 | RI15,R116 Resistor, 4 W, 1K Q, +5% | 110000-102 | ||
| R3, R4 | Resistor, 4 W, 1K Q, +5% | 110900-102 | RI7 | Resistor, 4 W, 4702, 45% | 110000-471 | |
| RS-R7 | Resistor, 4 W, 2208, +5% | 110000-221 | ||||
| R8-RLI | Resistor, 4 W, 4.7K Q, +5% | 110000-472 | RiU8 | Resistor, 4 W, 4702, +5% | 110000-471 | |
| R19 | Resistor, 4 W, 470K Q, +5% | 110000-474 | ||||
| RI2 | Resistor, 4 W, 4700, +5% | 110000-471 | R120-R124. Resistor, 4 W, 100K Q, +5% | 110000-104 | ||
| RI3Z-R20 | Resistor, 4 W, 1000; +5% | 110000-101 | R125 | Resistor, 4 W, 22K Q, +5% | 110000-222 | |
| R21-R23_ | Resistor, 4 W, 1K 2, +5% | 110000-102 | ||||
| R24-R27 | Resistor, 4 W, 4.7K Q, 45% | 110000-472 | R126, R127_ Resistor, 4 W,4.7KQ, +5% | 110000-472 | ||
| R128 | Resistor, & W, 2.2K Q, +5% | 110000-222 | ||||
| R28-R33__Resistor, 4 W, 4700, £5% | 110000-471 | R129 | Resistor, 4 W, 100K Q, + 5% | 110000-104 | ||
| R34 | Resistor, 4 W,10KQ, +5% | 110000-103 | R130 | Resistor, 4 W, 47K @, | 5% | 110000-473 |
| R35, | Resistor, 4 W, 1K Q, 5% | 110000-102 | ||||
| R36 | Resistor, 4 W, 2200, +5% | 110000221 | Ri31-R133_ Resistor, % W, 100KQ, 15% | 110000-104 | ||
| R134 | Resistor, % W, 47K Q, 45% | 110000-473, | ||||
| R37 | Resistor, % W, 2200, +5% | 110000-221 | RI35-R138 Resistor, 4 W, 100K Q, +5% | 110000-104 | ||
| R38-R42_—_Resistor, 4 W, 1KQ, +5% | 110000-102 | R139 | Resistor, 4 W, 47K Q, 45% | 110000-473 | ||
| R43-R58 | Resistor, 4 W, 10KQ, +5% | 410000-103 | ||||
| RS | Resistor, %4 W,1KQ, £5% | 110000-102 | R140 | Resistor, 4 W, 68K 2, +5% | 110000-683 |
R141, R142 Resistor, 4 W, 47K Q, +5% 110000-473
| R6O-R67 | Resistor, 4 W, 3.3K Q, +5% | 110000-332 | R143 | Resistor, 4 W,68KQ, +5% | 110000-683 |
| R68 | Resistor, 4 W, 1K @. 45% | 110000-102 | R144 | Resistor, 4 W, 47K Q, +5% | 110000-473 |
| ROO | Resistor, 4 W, 18KQ, +5% | 110000-182 | |||
| R70 | Resistor, %4 W, 10K @, 5% | 110000-103 | R148, RIS1_ Resistor, 4 W, 100KQ, +5% | 110000-104 |
R155, RIS6 Resistor, 4 W, 4709, +5% 110000-47i
| R71 | Resistor, 44 W, 5.0K Q, | 5% | 110000-562 | RIS7 | Resistor, 4 W,10KQ, +5% | 110000-103 |
| R72-R74 | Resistor, 4 W, 100K @, +5% | 110000-104 | R158, R159 Resistor, 4 W, 3.3K Q, +5% | 110000-332 | ||
| RIS | Resistor, 4 W, IK @, +5% | 110000-102 | ||||
| R7G-R85 | Resistor, 4 W, 10K Q, 45% | 110000-103 | R100 | Resistor, 4 W, IKQ, 45% | 110000-102 | |
| R161 | Resistor, % W, 1509, +5% | 110000-151 | ||||
| R86 | Resistor, 4 W, 2209, +5% | 110000-221 | R162 | Resistor, 4 W, 10KQ, +5% | 110000-103 | |
| R87 | Resistor, 4 W, 2209, +5% | 110000-221 | R163, | Resistor, 4 W, 33K 9, +5% | 310000-332 | |
| R88,R89 | Resistor, 4 W, 10K Q, +5% | 110000-103 | ||||
| R90. | Resistor, 4 W, 1002, +5% | 110000-101 | R164, R166 Resistor, 4 W, 1KQ, +5% | 110000-102 | ||
| R168 | Resistor, 4 W, IKQ, +5% | 110000-102 | ||||
| ROL | Resistor, 4 W, 4.7KQ, +5% | 110000-472 | R169, R170 Resistor, 4 W,4.7KQ, 45% | 110000-472 | ||
| R92 | Resistor, 4 W, 1002, +5% | 110000-101 | RII | Resistor, 4 W, 270.0, +5% | 310000-271 | |
| R93 | Resistor, 4 W, 4.7KQ, 45% | 110000-472 | ||||
| RO | Resistor, 4 W, 22K Q, +5% | 110000-223 | RI72 | Resistor, 4 W, 12.2, +5% | 110000-123 | |
| R173 | Resistor, 4 W, 560, +5% | 110000563 | ||||
| ROS | Resistor, 4 W, 47K Q, +5% | 110000-473 | RI74 | Resistor, 4 W, 10KQ, +5% | 110000-103 | |
| R96 | Resistor, 44 W, 100K Q, +5% | 110000-104 | RIS | Resistor, 4 W, 8.20, +5% | 110000-822 | |
| R97 | Resistor, 4 W, 22K @, + 5% | 110000-223 | ||||
| ROB | Resistor, 4 W, 47K Q, 45% | 110000-473 | R176 | Resistor, 4 W,3.9KQ, 25% | 110000392 | |
| ; | R177 | Resistor, 4 W, 4702, 45% | 110000-471 | |||
| ROD | Resistor, 4 W, 100K 0, +5% | 110000-104 | RI78 | Resistor, 4 W, 1K Q, +5% | 110000-102 | |
| R100 | Resistor, 4 W, 22K Q, +5% | 110000-223 | R179 | Resistor, 4 W, 00, +5% | 110005-001 | |
| R101 | Resistor, 4 W, 47K Q, +5% | 110000-473 | RN1,RN2 | Resistor Network, SIP, 10Kx8, 1/8W — 118002-103 | ||
| R102 | Resistor, %4 W, 100K @, +5% | 110000-104 |
q " 9% Miscellaneous
| R103 | Resistor, 4 W, 100K 2, 45% | 110000-104 | a | Voltage Regulator, Type-7905 | 37-7908 |
| R104, R1OS. Resistor, 4 W, 1K @, 45% | 110000-102 | ¥1 | G |
: cystal, 20 MHz. 144000-003
| R106 | Resistor, 4 W, 100K&, 45% | 310000-104 | ’ | ||
| R107, R108 Resistor, 4 W, 18K 2, +5% | 110000-183 | v2 | Crystal, 14.318 MHz | 90-101 | |
| 4 | Ns | a | 5/64 | Switch, 8 Position, DIP | 160031-008 |
| OTA | Switch, 8-Position, DIP | 160031-008 |
“x” in the part number denotes the revision level 5-21
5-22 Figure 5-9 APB Video PCB Assembly A044519-01 A Illustrated Parts Lists
é 1g sat Y) eee sis
Freererrree gree re
a | os tt ey amg
ut oy oe) doe fee)
3 aecost-t119 + sge0ss-2209 yo oo Lsis3
q 1 Favs s3005i-1109 1 Lsisa os
| Sie ee Pipes il E, Fare
rea roo] _sa at 36051-1825
+ ape? n rues ss ct
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING
CONFIDENTIAL: Reproduction forbidden without the specie wrtten permission of Atari Games Corporation, Mifitas, CA. This drawing is only conditionally issued, and neither receipt Nor possession thereof confere or transfers any right in, or ioerse to use, the subject matter of he drawing any deg of technical intraton shown hereon, nor any nigh to reprodune hs Craving or ary pt herent. Except or manufacture by vendors of Atari Games Corporation, and for manufaciure under the corporalion’s writen icense, no right is granted to reproduce this drawing
‘or the subject matter thereof, unless by writen agreement with or written permission from the corporation. APB
APB Illustrated Parts Lists
APB Video PCB Assembly Parts List
Desig- Desig-
| nator | Description | Part | nator | Description | Part No. |
| Integrated Circuits | 3L | ‘Type-6116P-3, 150 ns RAM | 137211.001 | ||
| 1A | Type-74L$157 Integrated Circuit | 37-74L8157 | Integrated Circuit | ||
| IB | Type-74L8157 integrated Circuit | 37-74L8157 | 3M | ‘Type-6116P-3, 150 ns RAM | 1372\1-001 |
| 1B/C | ‘Type-74LS157 Integrated Circuit | 37-7418157 | Integrated Circuit | ||
| icD | ‘Type-74L8244 Integrated Circuit | 37-74L8244 | 3N | ‘Type-748174 Integrated Circuit | 137209-001 |
| 3P | ‘Type-74F374 Integrated Circuitt | 137420-001 | |||
| IDE | ‘Type-74L8244 Integrated Circuit | 37-74L8244 | |||
| IBIF | Type-7418244 Integrated Circuit | 37-74LS244 | 3R | ‘Type-74F374 Integrated Circuitt | 137420-001 |
| 1F/K | ‘Type-74L8245 Integrated Circuit | 37-7ALS245 | 38 | ‘Type-7418273 Integrated Circuit | 37-74L8273 |
| 1H | ‘Type-7418245 integrated Circuit | 37-74L8245 | 3T | Type-74F374 Integrated Circuitt | 137420-001 |
| 4A | Type-74804 integrated Circuit | 37-74804 | |||
| y | ‘Type-7418244 Integrated Circuit | 37-74L8244 | |||
| ik | ‘Type-74LS374 Integrated Circuit | 37-74L8374 | 4BIC | ‘Type 6264-15 RAM Integrated Circuit | 137441-001 |
| IL | Type-74L$32 Integrated Circuit | 37-74L832 | 4c | ‘Type 6264-15 RAM Integrated Circuit | 137441001 |
| IM | Type-7418244 integrated Circuit | 37-74L8244 | DIE | “Type-741$163A Integrated Circuit | 37-7ALS163A |
| 4E/F | ‘Type-74874 integrated Circuit | 37-74874 | |||
| in | ‘Type-7418374 Integrated Circuit | 37-74L9374 | |||
| IP | ‘Type-74L8244 Integraied Citcuit | 37-74LS2-44 | 4F/H | ‘Type-74L8174 Integrated Circuit | 37-7418174 |
| IR | ‘Type-74L$244 Integrated Circuit | 37-7418244 | aH | ‘Type-74L$273 Integrated Circuit | 37-7ALS273 |
| 18 | Type-74L8244 Integrated Circuit | 37-74L8244 | a | ‘Type-74L8283 Integrated Circuit | 137204-001 |
| AK | Type-741$283 Integrated Circuit | 137204-001 | |||
| iv | Type-74874 Integrated Circuit | 37-14874 | |||
| 24 | ‘Type-74L$244 Integrated Circuit | 37-7418 244 | 4KiL | Type-74L8273 Integrated Circuit | 7-74LS273 |
| 2B | Type-74L8153 Integrated Circuit | 37-74L8153 | 4M | Type-74F374 Integrated Ciscuitt | 137420-001 |
| 2BIC | ‘Type-7415374 Integrated Circuit | 37-74L8374 | 4MIN | Type-828 131 Programmable PROM | 136034-131 |
Integrated Circuit
| 2c | ‘Type-741832 Integrated Circuit | 37-741832 | 4NP | ‘Type-74F374 Integrated Circuitt | 137420-001 |
| 2D | ‘Type-74L5174 Integrated Circuit | 37-74i8174 | |||
| 2E/F | ‘Type-74LS153 Integrated Circuit | 37-7418153 | 4P/R | Type-74L8273 Integrated Circuit | 37-TALS273 |
| 25H | ‘Type-74L8153 Integrated Circuit | 37-74LS153 | ARIS | Type-74F374 Integrated Circuitt | 137420-001 |
| aT | ‘Type-27128, EPROM, Integrated Circuit | 136051-x125 | |||
| 2H | “Type-74L8153 Integrated Circuit | 37-74L8153 | 5A | Type-74L$109 Integrated Circuit | 37-7418109 |
| ay | Type-74S174 Integrated Circuit | 137209-001 | |||
| 2k | ‘Type-74874 Integrated Circuit | 37-74874 | 5B | ‘Type-74508 Integrated Circuit | 37-74808 |
| aL | ‘Type-74L5139 Integrated Circuit | 37-74LS139 | SBIC | Type-74L808 Integrated Circuit | 37-74L808 |
| ScD | Type-74L8163A Integrated Circuit | 37-74L8163A | |||
| 2M | ‘Type-74L8153 Integrated Circuit | 37-74L8153 | SDE | ‘Type-74L8163A Integrated Circuit | 37-7415163A |
| 2N | ‘Type-74L$153 Integrated Circuit | 37-7418153 | |||
| 2P | ‘Type-7418374 Integrated Ciccuit | 37-74L8374 | SER | ‘Type-74F163 Integrated Circuit* | 137345-001 |
| 2R | ‘Type-74L8374 Integrated Circuit | 37-74LS374 | SH/H | ‘Type-74L804 integrated Circuic | 37-74L804 |
| SH | Type-27512, EPROM, Integrated Circuit | 136051-x112 | |||
| 2s | Type-74L5374 Integrated Circuit | 37-74L8374 | SVK | ‘Type-27512, EPROM, Integrated Ciscuit | —136051-x111 |
| QT | ‘Type-74832 Integrated Circuit | 37-T4832 | |||
| 3A | ‘Type-74F374 Integrated Ciscuitt | 137420001 | SKA, | ‘Type-27512, EPROM, Integrated Circuit | —_136051-x110 |
| 3B | ‘Type-74F374 Integrated Circuitt | 13 7420-001 | 5M | Type-27512, EPROM, Integrated Circuit | 136051-x109 |
| 5N | ‘Type-27512, EPROM, Integrated Circuit | 136051-x104 | |||
| 3BIC | ‘Type-74F374 Integrated Circuitt | 337420-001 | SPIR | ‘Type-27512, EPROM, Integrated Circuit | 136051-x103 |
| 3C/D | Type-74LS163A Integrated Circuit | 37-74LS163A | |||
| 3DE | Type-74L5163A Integeated Circuit | 37-74LS163A | SRS | ‘Type-27512, EPROM, Integrated Circuit | 13605-x102 |
| 3B/F | Type-745157 Integrated Circuit | 37-748157 | oT | ‘Type-27512, EPROM, Integrated Circuit | 136051-x101 |
| OA | ‘Type-27512, EPROM, Integrated Circuit. | —136051-x1i8. | |||
| 3F/H | ‘Type-74L8273 Integrated Circuit | 37-7418273 | OBC | ‘Type-27512, EPROM, Integrated Circuit | 136051120 |
| 3H | Type-741.8273 Integrated Circuit | 37-74L8273, | |||
| 3H | Type6116P-3, 150 ns RAM | 137211-001 | 6c | ‘Type-27256, EPROM, Integrated Circuit | 136051-x117 |
| Integrated Circuit | ODE | ‘Type-27512, EPROM, Integrated Circuit | —136051-x119 | ||
| 3K | Type-6116P-3, 150 ns RAM | 137211-001 | IER | ‘Type-74L$32 Integrated Circuit | 37-74L832 |
| Integrated Circuit | OTF | Type-74LS1 74 Integrated Circuit | 37-T4LS174 |
“x"' in the part number denotes the revision level “Acceptable substitute is Type-74AS163N Integrated Circuit, part no. 137421-001 tAcceptable substitute is Type-74AS374N Integrated Circuit, part no. 137422-001 5-23
SMustrated Parts Lists APB
APB Video PCB Assembly Parts List, Continued
Desig- Desig-
| aator | Description | Part No. | nator | Description | Part No. |
| GEF | ‘Type-74LS163A Integrated Circuit | 37-74L8163A, | 9BIC | ‘Type-748189 Integrated Circuit | 37-748189 |
| OF/H | ‘Type-74LS138 Integrated Circuit | 137177-001 | 9CciD | Type-74S189 Integrated Circuit | 37-748189 |
| GH | Type-27512, EPROM, Integrated Circuit | 136051-x116 | 9D | ‘Type-748189 Integrated Circuit | 37-748189 |
| OK | ‘type-27512, EPROM, Integrated Circuit. | 136051-x115 | 9E | Type-748189 Integrated Circuit | 37-748189 |
| KIL | ‘Type 27512, EPROM, Integrated Circuit | 136051-x1i4 | OF | ‘Type-74LS04 Integrated Circuit | 37-74L804 |
| oM | Type-27512, EPROM, Integrated Circuit | 136051-x113 | oH | Type-74S153 Integrated Circuit | 137207-001 |
| ON | ‘Type-27512, EPROM, Integrated Circuit | 136051-x108 | gy | ‘Type-74L8244 Integrated Circuit | 37-TALS244 |
| PIR | Type27512, EPROM, Integrated Circuit | 136051-x107 | OK | ‘Type-74374 Integrated Circuitt | 137420-001 |
| RIS | ‘Type-27512, EPROM, Integrated Circuit | 136051-x106 | OL | ‘Type-74F374 Integrated Circuitt | 137420-001 |
| or | ‘Type-27512, EPROM, Integrated Circuit | 136051-x105 | OM. | Type-748244 integrated Circuit | 137333-001 |
| 7A | Type27512, EPROM, Integrated Circuit | 136051-x122 | ON | ‘Type-2149, 35 ns Static RAM | 137199-063 |
| BIC | Type-27256, EPROM, Integrated Circuit | 136051-x124 | Integrated Circuit | ||
| op | ‘Type-2149, 35 ns Static RAM | 137199-003 | |||
| TCD | ‘Type-27512, EPROM, Integrated Circuit | 136051-x123 | Integrated Circuit | ||
| DIE | ‘Type-27512, EPROM, Integrated Circuit | 136051-x121 | |||
| TEIF | ‘Type-74LS00 Integrated Circuit | 37-74L800 | OR | Type-74F163 Integrated Circuit* | 137345-001 |
| TEI | Type-74808 Integrated Circuit | 37-74808 | 98, | ‘Type-74F163 Integrated Circuit* | 137345-001 |
| oT | ‘Type-74F163 Integrated Circuit* | 137345-001 | |||
| THY | Type-74L8158 Integrated Circuit | 137203-001 | 104 | ‘Type-745158 lategrated Circuit | 137312-001 |
| a | Type-74L8158 Integrated Circuit | 137203-001 | |||
| 1K | Type-748194 Integrated Circuit | 137424-001 | 108 | ‘Type-74374 Integrated Circuitt | 137420-001 |
| 7L | ‘Type-748194 Integrated Circuit | 137424-001 | 10B/C | Type-74800 Integrated Circuit | 37-7400 |
| 10Cc/D | ‘Type-748283 Integrated Ciccuit | 137241-001 | |||
| ™ | ‘Type-741158 Integrated Circuit | 137203-001 | 10D | Type-748153 integrated Circuit | 137207-001 |
| 7N | Type-74L5158 Integrated Circuit | 137203-001 | |||
| 7P | Type-748194 Integrated Circuit | 137424-001 | 10E | ‘Type-74S153 Integrated Circuit | 137207-001 |
| 7R | Type-748194 Integrated Circuit | 137424.001 | 10F | “Type-7418244 Integrated Circuit | 37-74L8244 |
| 10H | Type-74L8244 Integrated Circuit | 37-74L8244 | |||
| 78 | Type-745194 Integrated Circuit | 137424-001 | 10) | ‘Type-74F374 Integrated Circuit | 137420-001 |
| 7T | Type-748194 Integrated Circuit | 137424-001 | |||
| 8A | ‘Type-748194 Integrated Circuit | 137424-001 | 10K | ‘Type-74F374 Integrated Circuit | 137420-001 |
| 8B | ‘Type-748194 Integrated Circuit | 137424-001 | 10L | ‘Type-74F374 Integrated Circuit | 137420-001 |
| 10M | “Type-748244 Integrated Circuit | 137333-001 | |||
| BIC | Type-748194 Integrated Circuit | 137424-001 | 10N | ‘Type-2149, 35 ns Static RAM | 137199-003 |
| 8ciD | Type-748194 Integrated Ciecuit | 137424-001 | Integrated Circuit | ||
| 8p | Type-74F163 integrated Citcuit* | 137345-001 | |||
| 8E | Type-74L$163A Integrated Circuit | 37-74LS163A | 10P | ‘Type-2149, 35 ns Static RAM | 137199-003 |
Integrated Circuit
| 8F | ‘Type-741$74 Integrated Circuit | 37-74L874 | 10R | ‘Type-74F163 Integrated Circuit* | 137345-001 |
| 8H | Type-748162 Integrated Circuit | 137342-001 | 108 | Type-74F163 Integrated Circuit* | 137345-001 |
| 83) | ‘Type-74194 Integrated Circuit | 137424-001 | 10T | ‘Type-74F163 Integrated Circuit* | 137345-001 |
| 8L | ‘Type-74L820 Integrated Circuit | 37-74L820 | |||
| HA | Type-748189 Integrated Circuit | 37-748189 | |||
| 8M | ‘Type-748244 Integrated Circuit | 137333-001 | MB | ‘Type-748158 Integrated Circuit | 137312-001 |
| 8N | Type-2149, 35 ns Static RAM | 137199-003 | BIC | ‘Type-74S112 Integrated Circvit | 137334-001 |
| Integrated Circuit | uci | ‘Type-74S00 Integrated Circuit | 37-74800 | ||
| 8p | ‘Type-2149, 35 ns Static RAM | 137199-603 | |||
| Integrated Circuit | MD | ‘Type-74808 integrated Circuit | 37-74808 | ||
| 8R | Type-74F 163 Integrated Circuit* | 137345-001 | iE | Type-748153 Integrated Circuit | 137207001 |
| iE | Type-2149, 45 ns Static RAM | 137199-002 | |||
| 8s | ‘Type-74F 163 Integrated Circuit* | 137345-061 | Integrated Circuit | ||
| 8T | ‘Type-74F163 Integrated Circuit* | 137345-001 | nA | “Type-2149, 45 ns Static RAM | 137199-002 |
| 9A, | ‘Type-745189 Integrated Circuit | 37-748189 | Integrated Circuit | ||
| 9B | ‘Type-745158 Integrated Circuit | 137312-001 |
‘x in the part number denotes the revision level ‘Acceptable substitute is Type-74AS 163N Integrated Circuit, part no. 137421-001 5-24 ‘tAcceptable substitute is Type-74AS374N Integrated Circuit, part no. 137422-001
APB Mlustrated Parts Lists
APB Video PCB Assembly Parts List, Continued
Desig- Desig-
| nator | Description | Part No. | nator | Description | Part No. |
| A | Type-2149, 45 ns Static RAM | 137199-002 | cl4 | Capacitor, Ceramic, 100 pK, 100 V | 122016-101 |
| Integrated Circuit | cis | Capacitor, Ceramic, .1 pF, 50V | 122002-104 | ||
| 1IK | ‘Type-2149, 45 ns Static RAM | 137199-002 | C16 | Capacitor, Ceramic, 100 pk 100 V | 122016-101 |
| Integrated Circuit | cl7 | Capacitor, Ceramic, .1 #E 50V | 122002-104 | ||
| ML | Type-74S32 Integrated Circuit | 37-74832 | |||
| 11M | Type-74820 integrated Circuit | 137423-001 | cis | Capacitor, Ceramic, 100 pk, 100 V | 122016-101 |
| Ci9-C138._— | Capacitor, Ceramic, .1 wf, 50V | 122002-104 | |||
| MIN | Type-74F10 Integrated Circuit | 137428-001 | C139-C141 | Capacitor, Ceramic, 001 pF 50 V | 122002-102 |
| ue | Type-74886 Integrated Circuit | 137002-001 | C144-C147 | Capacitor, Ceramic, .1 pF, 50 V | 122002-104 |
| IIR | Type-74L832 Integrated Circuit | 37-74L932 | |||
| us | ‘Type-74L$08 Integrated Circuit | 37-74LS08 | Connectors | ||
| Ji3 | Connector, Header, 11-Circuit | 179014-011 | |||
| AIT | Type-74LS32 Integrated Circuit | 37-74L832 | -156 Ctr,, Pol | ||
| 124 | ‘Type-74874 Integrated Circuit | 37-74874 | Jy | Connector, Header, Sq. Pin, | 179118-011 |
| 12B | Type-74510 Integrated Circuit | 137236-001 | 11-Circuit, .100 Ctr. | ||
| 12B/C | ‘Type-74S04 Integrated Circuit | 37-74804 | JP1-JP6 | —Connecior, Header, 6 Cxt. (2 rows x 3 | 179177-006 |
Ckt.), 100 Ctr.
| 12C/D | ‘Type-74874 Integrated Circuit | 37-74874 | JP1-JP6 | Connector, Receptacle, 2 Ckt. | 179178-002 |
| 12D | Type-74820 Integrated Circuit | 137423-001 | |||
| 12E | ‘Type-748174 Integrated Circuit | 137209-001 | Ferrite Beads and Inductors | ||
| 12F | Type-74L8174 integrated Circuit | 37-74L8174 | Ll | Inductor, 1 pH | 141007-001 |
| L2-14 | Ferrite Bead | 141003-005, | |||
| 12H | ‘Type-74F374 Integrated Circuitt | 137420-001 | 15 | inductor, 100 pit | 141019-001 |
| 12) | ‘Type-74F374 integrated Circuit | 137420001 | |||
| 12K | ‘Type-74F374 Integrated Circuit} | 137420-001 | ‘Transistors | ||
| 121, | Type-7406 Integrated Circuit | 37-7406 | Q1@ | ‘Type-2N3904 ‘Transistor | 34-2N3904 |
| 3 | Type-2N3906 Transistor | 33-2N3906 | |||
| 13A | ‘Type-74LS74 Integrated Circuit | 37-74LS74 | rors | ‘Type-2N3904 ‘Transistor | 34-2N3904 |
| 13B | Type-74S112 Integrated Circuit | 137334-001 | 5 | ‘Type-2N3906 Transistor | 33-2N3906 |
| 13BIC | Type-74L532 Integrated Circuit | 37-741832 | |||
| 13cm | Type-74L8260 Integrated Circuit | 137332-001 | 6.7 | Type-2N3904 Transistor | 34-2N3904 |
| 8 | ‘Type-2N3906 Transistor | 33-2N3906 | |||
| BD | ‘Type-7407 Integrated Circuit | 37-7407 | Q9, QO | Type-2N3904 ‘itansistor | 34-2N3904 |
| 13E | Type-745174 Integrated Circuit | 137209-001 | Qu | Type-2N3906 Transistor | 33-2N3906 |
| 13F | ‘Type-74LS08 Integrated Circuit | 37-74LS08 | Qu | Type-2N3904 ‘Transistor | 34-2N3904 |
| 13H | Type-74F374 Integrated Circuitt | 137420-001 |
Resistors
| 13) | ‘Type-74LS260 Integrated Circuit | 137332-001 | Ri | 150.0, +5%, '4 W Resistor | 110000-151 | |
| 13K | ‘Type-7406 Integrated Circuit | 37-7406 | R2 | 10KQ, £5%, % W Resistor | 110000-103 | |
| 13L | Type-7406 Integrated Circuit | 37-7406 | R4 | 8.0, | 5%, A W Resistor | 110000-680 |
| RI7,R18 | 2200, +5%, %& W Resistor | 110000-221 |
Sockets
| 28-Contact, Medium-Insertion-Force IC | 79-42C28 | R19 | 1K, +5%, % W Resistor | 110000-102 | ||
| Socket | R20 | 1200, £5%, 4 W Resistor | 110000-121 | |||
| R21,R22 | 1802, +5%, & W Resistor | 110000-181 | ||||
| Capacitors | R23 | 2200, £5%, 4 W Resistor | 110000-221 | |||
| Ci, C2 | Capacitor, Aluminum, 100 pk, 35.V | 24350107 | ||||
| C3, C4 | Capacitor, Ceramic, .1 | 50V | 122002-104 | R24 | 470.0, £5%, W Resistor | 110000-471 |
| cS | Capacitor, Aluminum, 100 pF, 35 V | 24350107 | R25 | 1KQ, £5%, % W Resistor | 110000-102 | |
| 7 | Capacitor, Electrolytic, 1, 50 V | 24-500105 | R26 | 2KQ, +5%, 4W Resistor | 110000-202 | |
| R27 | 150.0, +5%, & W Resistor | 110000-151 | ||||
| ce | Capacitor, Ceramic, .1 uF, 50 V | 122002-104 | ||||
| co | Capacitor, Mica, 47 pF, 100 V | 128002-470 | R28 | 3.9KM, +5%, %& W Resistor | 410000-392 | |
| Cio | Capacitor, Mica, 68 pF, 100V | 128002-680 | R29 | 3900, 45%, ta W Resistor | 119000-391 | |
| C1I-C13 | Capacitor, Ceramic, .1 uF 50V | 122002-104 | R30 | 68.0, 45%, 4 W Resistor | 110000-680 | |
| R31 | 470, +£5%, % W Resistor | 110000-471 |
“x” in the part number denotes the revision ievel *Acceptabie substitute is Type-74AS163N Integrated Circuit, part no, 137421-001 {Acceptable substitute is Type-74AS374N Integrated Circuit, part no. 137422-001 5.25
Tilustrated Parts Lists APB
APB Video PCB Assembly Parts List, Continued.
Desig- Desig-
| nator | Description | Part No. | nator | Description | Part No. |
| R32 | 680, +5%, % W Resistor | 110000-680 | R53. | 1600, +5%, % W Resistor | 110000-161 |
| R33. | 10Q, 5%, 4 W Resistor | 110000-100 | R54 | 390.2, +5%, 4 W Resistor | 110000-391 |
| R34 | 6200, +5%, 4 W Resistor | 110000-621 | R55, | 68.0, +5%, 4 W Resistor | 110000-680 |
| R35, | 1.2KQ, +5%, 4 W Resistor | 110000-122 | R56 | 4700, +5%, % W Resistor | 110000-471 |
| R36 | 2.4KQ, +5%, 4 W Resistor | 110000-242 | R57 | 68.0, +5%, % W Resistor | 110000-680 |
| R37 | 5.1KQ, +5%, %& W Resistor | 110000-512 | R58. | 102, +5%, % W Resistor | 110000-100 |
| R38 | 8200, +5%, % W Resistor | 110000-821 | R59 | 6202, +5%, 4 W Resistor | 110000-621 |
| R39 | 10KQ, £5%, 4 W Resistor | 110000-103, | ROO | 1.2KQ, +5%, 4 W Resistor | 110000-122 |
| R40, R41 | 1602, +5%, 4 W Resistor | 110000-161 | R61 | 2.4KQ, +5%, 4 W Resistor | 110000-242 |
| R42 | 3900, +5%, %4 W Resistor | 110000-391 | RO2 | 5.1K Q, +5%, 4 W Resistor | 110000-512 |
| R43 | 68.2, +5%, 4 W Resistor | 110000-680 | ROS | 820, +5%, % W Resistor | 110000-821 |
| R44 | 4700, £5%, 4 W Resistor | 110000-471 | R64 | 10KQ, £5%, 4 W Resistor | 110000-103 |
| R45 | 68.2, +5%, 4 W Resistor | 110000-680 | R65-R75 | KQ, +5%, % W Resistor | 110000-102 |
| R46 | 10Q, +5%, 4 W Resistor | 110000-100 | R78 | 2200, +5%, % W Resistor | 11000-221 |
| R47 | 620, +5%, 4 W Resistor | 110000-621 | R79-R81 | 4700, +5%, “ W Resistor | 110000-471 |
| R48 | 1.2KQ, +5%, 4 W Resistor | 110000-122 | RNI,RN2___ | Resistor Network, SIP, 68092 x 7 | 118007-681 |
| R49 | 24KQ, £5%, %& W Resistor | 110000-242 | Miscellaneous | ||
| R50 | 5.1KQ, +5%, % W Resistor | 110000-512 | C142 | Filter, Feed-Thru, 2000 pF, 15A | 140002-001 |
| RSI | 8202, +5%, 4 W Resistor | 110000-821 | CRI | Diode, Light-Emitting, Type-MV5053 | 38-MV5053 |
| R52 | 10KQ, +5%, 4 W Resistor | 110000-103 | ‘TAB | ‘Terminal, Fast-On (Acceptable substitute | 179051-002 |
is Test Point, part no. 020670-001
| YI | Crystal, 32 MHz | 144003-002 |
Terminal, Ring Lug, #8, Solder Tab 179005-002
“x” in the part number denotes the revision level “Acceptable substitute is Type-74AS163N Integrated Circuit, part no. 137421-001 5-26 Acceptable substitute is Type-74AS374N Integrated Circuit, part no. 137422-001
APB Illustrated Parts Lists
N O T E S
5-27
Ilustrated Parts Lists APB
§-8T3 8739 TO
=a {_ [| Jacoc ‘S82 JSpK
Figure 5-10 Audio II PCB Assembly A043661-01 D
APB Illustrated Parts Lists
Audio II PCB Assembly Parts List
| Designator | Description | Part No. |
Capacitors
| C1-c5 | 3300 uF, 25 V Radial Electrolytic Capacitor | 123003-338, |
| C6-C12 | .1 pE, 50 V Ceramic Capacitor | 122002-104 |
| C13-C14 | 22 pF, 35 V Electrolytic Capacitor | 24-350226 |
| C15-C18 | .22 wk, 25 V Ceramic Capacitor | 122006-224 |
| C€19-C20 | .901 uF, 50 V Ceramic Capacitor | 122002-102 |
| C21-C23 | .1 #E 50 V Ceramic Capacitor | 122002-104 |
Diodes
| CR1-CR4 | ‘Type-1N5401 Diode | 31-1N5401 |
| CR5-CR10 | ‘Type-1N4001 Diode | 31-1N4001 |
| CR13 | Type-1N4002 Diode | 31-1N4002 |
Connectors
| JACDC | Key 2, 9 Ckt., .156-Inch Ctr. Header Connector | 179213-009 |
| JAUX | Key 6, 9 Ckt., .156-Inch Ctr. Header Connector | 179213-009 |
| JCDL | 2 Ckt., .156-Inch Ctr. Header Connector | 179213-002 |
| JSPK | Key 3, 6 Ckt., .156-Inch Ctr. Header Connector | 179213-006 |
Integrated Circuits
| Q1-Q2 | ‘Type-TDA-2030 Amplifier | 137301-001 |
| Q | Standup Type-7815 Integrated Circuit | 37-7815 |
Resistors
| Rt | 10 k@, Dual Horizontal Pot Resistor | 119011-103 |
| R3 | 102, +5%, % W Resistor | 110000-100, |
| R4-R7 | 22kQ, +5%, 4 W Resistor | 110000-223 |
| R8-R9 | 10kO, +5%, 4 W Resistor | 110000-103 |
| R1O-R11 | 1kQ, +5%, 4% W Resistor | 110000-102 |
| R12-R13 | 10, +5%, % W Resistor | 110000-010 |
| R14, R17 | OO, +5%, %& W Resistor | 110005-001 |
Miscellaneous
| SW1 | SPDT Miniature Slide Self-Test Switch | 69-004 |
| TP28-TP29 | #6-32 x 3/8-Inch Cross-Recessed Pan-Head Screw | 72-1606S |
| TP28-TP29 | #6-32 Nut/Washer Assembly | 75-99516 |
| TP28-TP29 | Thermal Compound | 78-16001 |
| TP28-TP29 | Type-TDA-230 Heat Sink | 178190-032 |
| TP101 | #4-40 x 3/8-Inch Cross-Recessed Pan-Head Screw | 72-1406S |
| TP10i | #4-40 Nut/Washer Assembly | 75-99514 |
| TP101 | Thermal Compound | 78-16001 |
| TP101 | Type-78 15 Heat sink | 178190-124 |
Hot Melt Adhesive 106006-001 Test Point 179051-001
5-29
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
AC Alternating current, from zero it rises to a maximum positive level, then passes through zero again to a maximum negative level. ACTIVE STATE ‘The true state of a signal. For example: The active state for START is low. ADDRESS: A value that identifies a specific location of data in memory; normally expressed in hexadecimal notation. ANALOG Measurable in an absolute quantity (as opposed to on or off). Analog devices are volume contols, light dimmers, stereo amplifiers, etc. ANODE The positive (arrow) end of a diode. AMPLIFIER A device used to increase the strength of an applied signal. AMPLITUDE The maximum instantaneous value of a waveform pulse from zero. ASTABLE Having no normal state. An astable device will free-run or oscillate as long as ‘operating voltage is applied. The oscillation frequency is usually controlled by external circuitry. AUXILIARY COIN SWITCH A momentary-contact pushbutton switch with a black cap located on the utility panel. The auxiliary coin switch adds credits to the game without activating a coin counter. BEZEL Acut, formed, or machined retention device, such as the conical device used to mount a pushbutton switch to a control panel, or the formed device used to frame the video display screen. BIDIRECTIONAL Able to send or receive data on the same line (¢.g., the data bus ofa mictoprocessor). BINARY A number system that expresses all values by using two digits (0 and 1). BIT A binary digit; expressed as 1 or 0. BLANKING ‘Turning off the beam on a cathode-ray tube during retrace. BLOCK DIAGRAM A drawing in which functional circuitry units are represented by blocks. Very useful during initial troubleshooting. BUFFER
- An isolating circuit designed to eliminate the reaction of a driven circuit on the circuits driving it (e.g., a buffer amplifier).
- A device used to supply additional drive capability. BUS An clectrical path over which information is transferred from any of several sources to any of several destinations. CAPACITOR A device capable of storing electrical energy. A capacitor blocks the flow of DC current while allowing AC current to pass. CATHODE The negative end of a diode. CHIP An integrated circuit comprising many circuits ona single wafer slice. CLOCK A repetitive timing signal for synchronizing system functions. COINCIDENCE Occurring at the same time. COIN COUNTER A 6-digit elecuomechanical device that counts the coins inserted in the coin mechanism(s). COIN MECHANISM A device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted. COMPLEMENTARY Having opposite states, such as the outputs ofa flip-flop. COMPOSITE SYNC Horizontal and vertical synchronization pulses that are bused together into a single signal. This signal provides the timing necessary to keep the display in synchronization with the game circuitry. COMPOSITE VIDEO Complete video signal from the game system to drive the display circuitry, usually comprising H SYNC, V SYNC, and the video.
Glossary
CREDIT One play for one person based on the game switch settings. CRT Cathode-ray tube. DATA. General term for the numbers, letters, and symbols that serve as input for device processing. DARLINGTON A two-transistor amplifier that provides extremely high gain. DC Direct current, meaning current flowing in one direction and of a fixed value. DEFLECTION YOKE Electromagnetic coils around the neck of acathode-ray tube. One set of coils deflects the electron beam horizontally and the other set deflects the beam vertically. DIAGNOSTICS A programmed routine for checking circuitry. For example: the self-test is a diagnostic routine. DIODE A semiconductor device that conducts. in only one direction. DISCRETE Non-integrated components, such as re- Sistors, capacitors, and transistors. DMA Direct memory access. DMA is a process of accessing memory that bypasses the microprocessor logic. DMA is normally used for transferring data between the input/output ports and memory. DOWN TIME The period during which a game is malfunctioning or not operating correctly due to machine failure.
EAROM Electrically alterable read-only memory (see ROM). The EAROM is a memory that can be changed by applying high voltage. EPROM Erasable programmable read-only memory (see ROM). FLYBACK A step-up transformer used in a display to provide the high voltage.
GATE 1, A circuit with One output that responds only when a certain combination of pulses is present at the inputs.
- A circuit in which one signal switches another signal on and off.
- To control the passage of a pulse or signal. HARNESS A prefabricated assembly of insulated wires and terminals ready to be attached to a piece of equipment. HEXADECIMAL A number system using the equivalent of the decimal number 16 as a base. The symbols 0-9 and A-F are usually used. HISTOGRAM A special type of bar graph that shows how quantities are distributed. Histograms are included in the self-test of most Atari games, and typically show how long players play that game. Ic Integrated circuit. An electronic circuit in which all elements and the connections are made in or on a single semiconductor substrate. See also chip. IMPLODE To burst inward; the inward collapse of a vacuum tube. vo Input/Output. IRQ Interrupt request. IRQ is a control signal to the microprocessor that is generated by external logic. This signal tells the microprocessor that external logic needs attention. Depending on the program, the processor may or may not respond. LED The abbreviation for a light-emitting diode. LOCKOUT COIL Directs coins into the coin return box when there is no power to the game. LOGIC STATE ‘The binary (1 or 0) value at the node of a logic element or integrated circuit during a particular time. Also called the logic level. The list below shows the voltage levels corresponding to the logic states (levels) ina TTL system. Logic 0, Low = 0 VDC to +0.8 VDC Grey Area (Tri-State Level) = +0.8 VDC to +2.4 VDC Logic 1, High = +2.4VDC to +5 VDC MULTIPLEXER A device that takes several low-speed inputs and combines them into one highspeed data stream for simultaneous transmission on a single line. NMI Non-maskable interrupt. NMI is a request for service by the microprocessor from external logic. The microprocessor cannot ignore this interrupt request. PAGE A subsection of memory. A read-only memory device (see ROM) is broken into discrete blocks of data. These blocks are called pages. Each block has X number of bytes. PCB The abbreviation for a printed-circuit board.
PHOTOTRANSISTOR A transistor that is activated by an external light source. POTENTIOMETER
- A resistor that has a continuously moving contact which is generally mounted ona moving shaft, Used chiefly as 2 voltage divider. Also called a pot (slang).
- An instrument for measuring a voltage by balancing it against a known voltage. RAM Random-access memory. A device for the temporary storage of data. RASTER-SCAN DISPLAY A display system whereby images are displayed by continuously scanning the cathode-ray tube horizontally and vertically with an electron beam. The display system controls the intensity of the electron beam. RETRACE Ina raster-scan display, retrace is the time during which the cathode-ray tube electron beam is resetting either from right to left or from bottom to top. RESISTOR A device designed to have a definite amount of resistance. Used in circuits to limit current flow or to provide a voltage drop. ROM Read-only memory. A device for the permanent storage of data. SIGNATURE ANALYSIS A process of isolating digital logic faults at the component level by means of special test equipment called signature analyzers. Basically, signature analyzers (eg,, the ATARI® CAT Box) convert lengthy bit streams into four-digit hexadecimal signatures. The signature read by the analyzer at each circuit node is then compared with the known good signature for that node. This process continues until a fault is located. TROUBLESHOOT The process of locating and repairing a fault.
VECTOR A line segment drawn between specific Xand Y coordinates on a cathode-ray tube.
‘WATCHDOG Acounter Circuit designed to protect the microprocessor from self-destruction if a program malfunction occurs. If a malfunction does occur, the counter applies continuous pulses to the reset line of the microprocessor, which causes the microprocessor to keep resetting, X-Y DISPLAY ‘A display system whereby images are displayed with vectors. ZENER DIODE Aspecial diode used as a regulator. Its main characteristic is breaking down at a specified reverse-bias (Zener) voltage.
Coin counters
Total on time
All Games
New Games
Continued APB’ Statistics
Date: Location:
Coin Information and Game Times
Li R: _____ Number of coins deposited in the left and right coin mechanisms, respectively
- Total time (in hours : minutes : seconds) that the game has been turned on
Number Total Time Avg. Time
Histograms of Game Times*
——— 12:00 4:00
8:00 3:30
7:30 3:00
| ——— | 7:00 | 2:30 | |
| 630 | —_— | 2:00 | |
| __ | 6:00 | - | 1:30 |
| ——__ | 5:30 | ——— | 1:00 |
| ———- | 5:00 | ——— | 0:30 |
| 4:30 | ——— | 0:00 |
“The green-highlighted reading indicates the number of new games. The red-highlighted reading indicates the number of continued games. (Continued on back)
APB" Statistics, continued
Day Histogram * *
22 sw
3 15
| — | 30 | _— |
| a.) | _— | B |
as Rp
7 oa
6 10
os )
_ ss
| 3 | _— | 7 |
| 2 | _ | 6 |
a 5s
| _ | 0 | 4 | |
| _— | 19 | 3 | |
| _ | 18 | _ | 2 |
| _ | 17 | _ | 1 |
**The green-highlighted reading indicates the number of times a day was started. The red-highlighted reading indicates the number of times a day was successfully completed.
SAR ee fanty- ee ‘cause injury to you afd orhtes, Be vere cantious TARing AaeAG supplicd Sompooeas. with or games; Er Onder td enstice: your safchy ~_-Atar disiribiton ase independent, being pvately owned nnd operated. 16 ibeirjadpmient: Hey may self nits Be wlcssesties other thin Aten pare ar ieieeitics Ati Games Carpi See Serpico k Pose Neate es ae aa ingdlificrion Welling tahoe which ia pertorned by sicly dimibitee:
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.