Pole Position TM-218 7th Printing
Pole Position (World) (Namco, 1982) · Technical Manual · 92 pages · 49 sections · original scan
Operation, Maintenance, and Service Manual
Complete with Schematics an
d Illustrated Parts Lists
\f reading through this manual does not lead to solving a certain maintenance problem, call TELEHELP® at the Atari Customer Service office in your geographical area, as shown below.
WEST and CENTRAL U.S.A. Parts and Service
Atari, Inc. California Customer Service Office 1105 N. Fair Oaks Avenue P. O, Box 427, Sunnyvale, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Pacific Time) From California, Alaska, or Hawaii Ss (408) 745-2900 Service from anywhere in the area shown in white @ oltre (800) 538-1611
EAST U.S.A. Service only
Atari, Inc. New Jersey Customer Service Office 12A World's Fair Drive, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) ‘ae From New Jersey (201) 469-5993 From anywhere else in this area toll-free (800) 526-3849
EUROPE
Parts and Service
Atari Ireland Limited European Customer Service Office Tipperary Town, Ireland Telex 28165 TIPPERARY TOWN, (Monday-Friday, 9:00-6:00 pm GMT) IRELAND @ 06252155
PEVyY
Operation, Maintenance, and Service Manual
Complete with Schematics
and Illustrated Parts Lists
*Pole Position is engineered and designed by Namco Ltd. Manufactured under license by Atari, Inc.
Pole Position
© 1982 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or elecironic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees, fines up to $25,000, and face an imprisonment of up to one year. Atari will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.
Published by: ATARI, INC. 790 Sycamore Drive P.O. Box 906 Milpitas, California 95035
Lithographed in the U.S.A. ™
Pole Position
Notice Regarding Non-ATARI Parts
Use of non-ATARI parts or modifications of your ATARI® game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.
You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: @ substitute non-ATARI parts in ihe game @ modify or alter any circuits in the game by using kits or parts not supplied by Atari.
to licensed communications services is not permitted by the Federal Communications Commission (FCC). If you suspect interference from an ATARI® game at your location, check the following: @ all green ground wires in the game are properly connected as shown in the the game wiring diagram @ the power cord is properly plugged into a grounded 3-wire outlet @ the game PCB is properly installed within the Electromagnetic Interference (EMI) cage @ the EMI Shield PCB is properly installed and in series with the game PCB harness. Refer to Figure 3-18 to make sure that the game PCB and the Shield PCB are correctly installed. If you are still unable to soive the interference problem, please contact ATARI Customer Service. See the inside front cover for service in your area.
iti
Pole Position
Table of Contents
1 Set-Up Procedures A. New Features 1-4 B. Inspecting the Game . 1-4 C. Leveling the Sit-Down Cabinet . 15 D. Space and Power Requirements 1-5
- Installation Requirements. 15
- Selecting the Voltage Plug 15 £. Locating the Switches ... 16
- Power On/Off Switch 16
- Utility Panel Switches 17
- Option Switches ...... 17
- Memory Back-Up Jumper . 1-7 F. Setting the Option Switches .. wee 17 G. Performing the Initial Self-Test. . wee 110 H. Game Play............- oe 112
- Attract Mode oe 4-12
- Play Mode .... -. 112
- High-Score Mode ... . 7 7 : . 14-13
- Hints forGame Play ......... 0... cece cece eee 413
2 Self-Test Procedure A. Comments on Troubleshooting ..............0.0 eee 2-2 B. Performing the Self-Test........... 0.0. ce seca eee 2-2
3 Maintenance, Repair, and Parts A. Cabinet-Mounted Assemblies ...................... 3-2 B. Player Controls...................0. 3-9 C. Fluorescent Tube and Speaker Replacemen 3-22 D. Video Display................0..000.. 3-26 E. Utility Panel . tne .. $28 F. CoinDoors........ -. 3-30 G. Printed-Circuit Boards .. 3-86 H. Power Supply Assembly... 022... cee ee 3-57
Glossary of Terms ...........0.0. 20.0 Gu
Figure 1-1 Figure 1-2 Figure 1-3 Figure 1-4
Figure 1-5 Figure 2.1 Figure 2-2 Figure 2-3 Figure 2-4
Figure 3-1 Figure 3-2 Figure 3-3 Figure 3-4
Figure 3-5 Figure 3-6 Figure 3-7 Figure 3-8
Figure 3-9 Figure 3-10 Figure 3-11 Figure 3-12
Figure 3-13 Figure 3-14 Figure 3-15 Figure 3-16
Figure 3-17 Figure 348 Figure 3-19 Figure 3-20
Figure 3-21 Figure 3-22 Figure 3-23 Figure 3-24
Table 1-1 Table 1-2 Table 1-3 Table 1-4
Table 2-1 Table 2-2 Table 2-3 Table 2-4 Pole Position
List of Illustrations
Game Overview, Upright Cabinet .........-......-.00 eee ee 1-2 Game Overview, Sit-Down Cabinet 1-3 Leveling the Sit-Down Cabinet .. . 16 Location of Game Switches. .......... 0.00.00 eee c eevee eee 16 Self-Test Display... 4-14 Self-Test Screen 1: ig! 2-3 Self-Test Screen 1: Sit-Down Test Passes . 2-3 Self-Test Screen 1: Test Fails ....... 23 Self-Test Screen 2 2-4
Illustrated Parts Lists Cabinet-Mounted Assemblies, Upright Cabinet ............... 3-2 Cabinet-Mounted Assemblies, Sit-Down Cabinet . 35 Control Panel. ...........-......020 008 -. 39 Control Panel Assembly .........- 00.0.0 eee eee cee eee 3-10 Steering-Wheel Control Assembly... ..........-. 0000002 ee . 312 Steering-Wheel Control Screw Adjustment . 3-14 Steering-Wheel Control Orientation . . » 315 Gear-Shifter Control Assembly ... 22.0.0... 0 ee ee eee 3-16
Foot-Pedal Control Assembly oe. 318 Foot-Pedal Cable Rewinding - 3-20 Fluorescent Tube and Speaker Board Removal, Upright Cabinet .. 3-22 Fluorescent Tube and Speaker Board Assembly, Upright Cabinet . 3-23
Sit-Down Cabinet Speaker Removal .................0.2-5 . 324 Video Display Removal........ . 3-26 Utility Panel Assembly |. . . 3-27 Vertically-Mounted Coin Door .... 22... 2... eee eee 3-29 American-Made Coin Door... 2.6.0... eee eee 3-32 Removing the Printed-Circuit Boards ............. . 3-35 Central Processing Unit Printed-Circuit Board Assembly . 3-37 Pole Position Video Printed-Circuit Board Assembly ............. 3-46
Regulator/Audio li PCB Assembly, U.S—Built Cabinet ........... 3-51 Regulator/Audio II PCB Assembly, Ireland-Built Cabinet . 3-52 EMI Shield PCB Assembly .................. . 3-55 Power Supply Assembly ...... 0.00.00... 0 cece cee eee 3-57
List of Tables
Switch Settings for Game and Price Options ................ Switch Settings for Game and Play Options . i9 Self-Test Procedure ............ . 1:10 Qualifying Lap Information . ee nner ras 113
Locating Failed Components on the Video PCB ............ 22 Locating Failed Components on the CPU PCB . 22 Locating the Failed ROM................ . 23 Locating the Failed RAM....... 2-4
Pole Position
vi
NOTICE
This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference.
Set-Up Procedures
How to Use this Manual
This manual, written for game operators and service technicians, describes the Pole Position game. The manual contains information about the Upright and Sit-Down Pole Position cabinets. Whenever information is unique to the Upright cabinet, this symbol appears: |
Whenever information is unique to the Sit-Down
cabinet, this symbol appears: fH games, this symbol appears: ry
Wherever information is unique to /reland-Built
Chapter 1 describes new features, game setup, settings of option switches, self-test procedures, and game play. Chapter 2 contains self-test procedures. Chapter 3 details maintenance, repair, and parts information. A glossary of terms is in the back of this manual for your convenience. In addition, schematic diagrams of the game circuitry are included with this manual. Figures 1-1 and 3-1 illustrate the Upright game cabinet; Figures 1-2 and 3-2 illustrate the Sit-Down game cabinet. Italicized lettering on these figures refers you to other places in the manual for information about specific cabinet parts.
Ra VA ee
——=
Set-Up Procedures
% VIDEO DISPLAY ATTRACTION PANEL, FLUORESCENT TUBE ‘AND SPEAKER See Figure 3-11 or 3-12 Pole Position
»% GAME IDENTIFICATION LABEL (Serial number appears here on Ireland-Built games)
‘See Figure 3-14 Sep Pais 15 7 ACCESS PANEL a and 3.23
DASHBOARD FAN ASSEMBLY
STEERING-WHEEL ‘See Figure 3-1 See Figure 3-1 ‘CONTROL ASSY. See Figure 3-5
UTILITY PANEL See Figure 3-15
COIN DOOR See Figures 3-16 & 3-17
Items with a serial number label on U.S.-Built cabinets GEAR-SHIFTER CONTROL ASSY. See Figure 3-8
CAPACITOR See Figure 3-24
CONTROL PANEL See Figures 3-3 & 3-4
SPEAKER See Figure 3-12
FOOT-PEDAL ASSEMBLY S Y
See Figure 3-9 %* POWER SUPPLY See Figure 3-24
- GAME PCBs See Figures 3-18, 3-19 & 320
REGULATOR/ AUDIO II PCBs See Figures 3-18, 321 & 3-22
POWER ON/OFF SWITCH
SHOCK HAZARD This game should only be connected to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. You may receive an electrical shock if the game is not properly grounded!
Figure 1-1 Game Overview
Upright Cabinet
Pole Position
- GAME IDENTIFICATION LABEL (Serial number appears on exterior of rear access panel of Ireland-built games)
- GAME PCBs FAN ASSEMBLY See Figures 3-18, See Figure 3-2 3-19 & 3-20 EMI CAGE See Figures 3-18 & 3-23
ACCESS PANEL Set-Up Procedures
UTILITY PANEL ASSY. See Figure 3-15
SPEAKER See Figure 3-13
+ REGULATOR! AUDIO il PCBs See Figures 3-18, 7S) 3-21 & 322 dae POWER ON/OFF SWITCH POWER SUPPLY Y4) See Figure 3:24 CAPACITOR Fi 4 See Figure 324 VipEo DISPLAY y
See Figure 3-14 @ | STEERING-WHEEL CONTROL ASSY. See Figure 3-5
GEAR SHIFTER CONTROL ASSY. See Figure 3-8
CONTROL PANEL See Figures 3:3 & 3-4
COIN DOOR
SHOCK HAZARD This game should only be connected to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. You may receive an electrical shock if the game is not properly grounded! See Figures 3-16 & 3-17
ACCELERATOR & BRAKE See Figure 39
x Items with a serial number label on U.S.-Built cabinets
Figure 1-2 Game Overview Sit-Down Cabinet
1:3
Set-Up Procedures
A. New Features
The Pole Position game has many new features. Even if you are familiar with ATARI® games, you should note these important differences: @ Electromagnetic Interference (EMI) Cage in U.S.-Built Cabinets Only. Games built after December 1, 1982, will have the CPU and Video printed-circuit boards (PCBs) mounted inside this cage. The EMI cage reduces interference from the game to television and radio receivers. See Figure 3-18 for details. @ American-Made Coin Door. Your game may be equipped with a new coin door. This door is very similar to the vertically mounted coin door, but does not have lockout coils. When ordering parts for your coin door, please check coin door illustrations in Figures 3-16 and 3-17 carefully to make sure you are ordering the correct part number. @ Steering-Wheel Control. This steering wheel is designed to provide a more realistic response from the race car on the display. @ Foot-Pedal Control (Accelerator and/or Brake). These pedals have been redesigned to accommodate a snap-action switch for the brake and a potentiometer, turned by a spring and cable, for the accelerator. @ Quadraphonic Sound in Sit-Down Cabinet. Four 4-ohm, 6-ounce, high-fidelity speakers (two under the control panel; two behind the seat) surround the player with the exciting and realistic sounds of Gran Prix racing. New features and other major parts of the game are shown in Figures 1-1 and 1-2. Throughout this manual, wherever a new feature is mentioned, you will see this symbol:
1-4 Pole Position
B. Inspecting the Game
Please inspect your game carefully to ensure that it was delivered to you in good condition.
Examine the exterior of the game cabinet for dents, chips, or broken parts. Remove the screws that were used as extra security to seal the rear access panel. Unlock and open this panel and the coin door; inspect the interior of the game as follows: a. Ensure that all plug-in connectors (on the game harness) are firmly plugged in. Replug any connectors found unplugged. Do not force connectors together. The connectors are keyed so they only fit in the proper orientation. A reversed edge connector may damage a PCB and will void your warranty. b. Ensure that all plug-in integrated circuits are firmly plugged into their sockets on the printed-circuit boards (PCBs). c. Remove the tie-wrap that secures the coiled power cord inside the cabinet. Inspect the power cord for any cuts or dents in the insulation. Repair or replace it as required. Place the square black plastic strain-relief plate in the wood slot at the bottom of the rear panel opening. d. Note the game serial number printed on a label on the back of the cabinet. Verify that the same serial number is also on the Pole Position game PCBs, Regulator/Audio II PCBs, power supply, and video display. See Figures 1-1 and 1-2 for locations of the serialnumbered components. Please mention the serial number whenever you call your distributor for service. e. Inspect major subassemblies, such as the power supply, control panel, and video display. Make sure they are mounted securely.
To avoid electrical shock, do not touch internal parts of the display with your hands or with metal objects held in your hands!
Pole Position
- For the Sit-Down cabinet, remove the metal attraction panel from the protective wrapping. Remove the three button-head screws and retainer on the front window. Place the attraction panel over the mounting holes. Reinstall the retainer and screws.
C. Leveling the Sit-
C. Leveling the Sit Down Cabinet
The Sit-Down cabinet rolls easily from location to location on 4-inch casters. To level the cabinet, lift the game up On one side. Place a block of wood, a book, or another object (that is at least 2-inches thick) under the raised cabinet. Partially unscrew the adjustable glides (see Figure 1-3) until they extend below the caster. Lower the game and lift it up on the other side; partially unscrew the adjustable glides. Lower the game. To prevent players from moving the game around, be sure to adjust all four glides.
CASTER
ADJUSTABLE GLIDE A
Figure 1-3 Leveling the Sit-Down Cabinet Set-Up Procedures
D. Space and Power Requirements
- Installation Requirements
Power 250 W Temperature 0° to +38°C (+ 32° to + 100°F) Humidity Not over 95% relative Upright Cabinet 62 x 90 cm (25% x 35% in) 186 cm (72% in.) Sit-Down Cabinet 165 x 64 cm (65 x 25% in.) 194 cm (76 in.) Space Required Game Height
Space Required Game Height
- Selecting the Voltage Plug
This game shouid only be connected to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a |icensed electrician to instal! a grounded outlet. You may receive an electrical shock if the game is not properly grounded!
The power supply used in this game operates on the line voltage of almost any country in the world. The power supply comes with either one, two, or three separate voltage-selection plugs. Plug voltages and wire colors are 100 VAC (violet wire color), 120 VAC (yellow wire color), 220 VAC (blue wire color), and 240 VAC (brown wire color), Before plugging in your game, check your line voltage. Next, check the wire color on the voltageselecion plug that is plugged into the game’s power supply. Make sure the voltage-selection plug is correct for the voltage of your location (see Figure 3-24). Now, plug the game into a grounded 3-wire outlet.
Set-Up Procedures
E. Locating the Switches
Do not depress the accelerator or brake pedal when turning on the game or switching to the Self-Test Mode. This will cause faulty program initialization and incorrect action of the player controls. Pole Position
- Power On/Off Switch
The power on/off switch is located on the back of the Upright cabinet on the lower left side. On the Sit- Down cabinet the power on/off switch is located on the lower left side of the cabinet (see Figure 1-4).
OPTION SWITCHES SWITCH AT SJA (Game and price) SWITCH AT 9L (Game and play)
information.
JUMPER AT 6B (Memory back-up) See CO-218-01 for NAMCO PCB UTILITY PANEL ASSY. See Figure 3-15
POWER ON/OFF SWITCH
Figure 1-4 Location of Game Switches
Pole Position
- Utility Panel Switches The volume control(s), self-test switch, coin counter(s), and auxiliary coin switch are located on the utility panel in both the Upright and Sit-Down cabinets (see Figure 3-72). The utility panel is located inside the upper coin door. The volume control(s) adjust the level of sound produced by the game. The Sit-Down cabinet has four volume controls: one for each speaker. The Upright cabinet has two volume controls: one for each speaker. The self-test switch is used to enter and exit the Self-Test Mode. The coin counter(s) record the number of coins entered into the game. The auxiliary coin switch is used to credit the game without activating the coin counter(s).
- Option Switches Option switches are located on the game CPU PCB (see Figure 1-4). Refer to supplement CO-218-01 for switch locations if your game has NAMCO PCBs.
a. Game and price options are at CPU PCB location QJA. b. Game and play options are at CPU PCB location 9L.
4, Memory Back-Up Jumper The memory back-up jumper is at CPU PCB location 6B. Position this jumper to the on setting. The memory back-up jumper is positioned on the off setting when shipped from the factory to prevent leakage and to provide longer life for the battery at location 6A on the CPU PCB. The jumper must be positioned to the on setting so that the battery can provide power to the CMOS memory. This memory stores the high-score table and operator statistics. Set-Up Procedures
The jumper does not affect game play. We recommend you position this jumper to the off setting when you expect extended downtime.
FE. Setting the Option Switches
Settings of the game option switches are explained in Tables 1-1 and 1-2. Options preset at the factory are shown by the < symbols. However, you may change the settings according to your individual needs. To verify option-switch settings, first set the power onloff switch to the off position and then to the on position. Next, set the self-test switch to the on position. Compare the information on the screen to the option switch settings listed in the tables in this section. Then set the self-test switch to the off position. Table 1-1 describes the switch settings for options relating to game price, coin mechanism multipliers, number of laps per game, and number of seconds per lap. These switches are on the game CPU PCB at location 9JA. The multipliers (QJA switches 1-5) determine the value of the Coin mechanisms io the game’s logic. A coin mechanism is a device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted. The mechanism either accepts or rejects the coin. The coin door has two coin mechanisms. The basic unit of measurement is a coin worth $.25 or 1 DM, which equals a multiplier of x1. For example, if you have a2 DM/1 DM coin door, you may want to set the left multiplier at x2 and the right multiplier at x1.
A A Pace Yd
Set-Up Procedures Pole Position
| Coin | Option | Interconnect | Assembly |
J55A-P55A permits a coin placed in either coin mechanism to register in the same coin counter. The cable connector is located between the coin door harness and the main harness (see the Coin Op-
| tion | Interconnect | Wiring | Diagram | in | ||
| SP-218). | When | it | is | used, | left | coin |
mechanism option switches at 9JA apply to both coin mechanisms. If you want different options for the left and right coin mechanisms, remove Coin
| Option | Interconnect | Assembly | J55A- |
P55A and connect J55 directly to P55. If you have NAMCO game PCBs, refer to CO-218-01 for the location of the option switches.
Table 1-1 Switch Settings for Game and Price Options
Settings of 8-Toggle Switch on Pole Position CPU PCB (at 9JA)
| 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | Option |
On 4 racing laps *
Off 3 racing laps
| Off | Off | 90 seconds per lap <4 |
| Off | On | 100 seconds per lap |
| On | Off | 110 seconds per lap |
| On | On | 120 seconds per lap * |
Right Coin Mechanism
| Off | Off | 1 coin for 1 credit < |
| Off | On | 2 coins for 1 credit * |
| On | Off | 3 coins for 2 credits |
| on | On | 4 coins for 3 credits |
Left Coin Mechanism
| Oft | Off | Off | 1 coin for 1 credit <4 |
| Off | Off | On | 1 coin for 2 credits |
| Off | On | Off | 1 coin for 3 credits |
| Off | On | On | 2 coins for 1 credit * |
| On | Off | Off | 3 coins for 1 credit |
| On | Off | On | 3 ccins for 2 credits |
| On | On | Off | 4 coins for 3 credits * |
| On | On | On | Free Play |
Manufacturer's recommended settings for Upright cabinet % Manufacturer's recommended settings for Sit-Down cabinet *This option setting can be changed to 1 coin for 6 credits by changing the program PROM (136014-160). Contact your distributor for further information.
Pole Position
We recommend that game difficulty for the race laps (EXTENDED RANK) and the qualifying lap (PRACTICE RANK) be increased periodically. These changes will ensure that Pole Position continues to offer maximum excitement and challenge. Except in locations with extremely skillful and advanced players, these settings should not be increased more than one level per month. Set-Up Procedures
Table 1-2 contains option-switch settings for Attract Mode sound and speed (kilometers or miles per hour). These switches are on the game CPU PCB. at location 9L. Pole Position leaves the factory with option switches set at the manufacturer's recommended difficulty level. The game will be exciting and challenging for players at these settings. Table 1-4 lists the manufacturer's recommended qualifying lap times. Table 1-5 lists option-switch settings for additional qualifying lap times. Table 1-6 provides switch settings for racing lap times.
Table 1-2 Switch Settings for Game and Play Options
Refer to CO-218-01 for switch locations if your game is equipped with NAMCO PCBs.
Settings of 8 Toggle Switch on Pole Position CPU PCB (at 9L) 8 7 6 5 4 3 2 1 Option
Off On
Off On Attract Mode sound off Attract Mode sound on
Kilometers per hour Miles per hour
“Manufacturer's recommended settings
Set-Up Procedures
G. Performing the Initial Self-Test
This game will test itself and provide data to show that the game's circuitry and controls are operating properly. The data is provided on the video display and speakers. No additional equipment is necessary. Wait at least 10 seconds after playing a game before switching to the Self-Test Mode. Otherwise, you may erase the top three scores in the high-score table or distort the statistics. All credits will be cancelled when you switch to self-test. Refer to Figure 1-4 for the location of the option switches and Figure 3-15 for the location of the selftest switch. Set the self-test switch to the on position (see Figure 1-5) to see the Self-Test Display in the Self-Test Mode. To exit the Self-Test Mode, set the self-test switch to the off position. Pole Position
The complete self-test procedure is explained in Chapter 2, B. Self-Test Procedure. \t a part of the test described in Table 1-3 fails, refer to Chapter 2. We suggest you perform the self-test procedure when you first set up the game, when you collect money from the game, when you change game options, or when you suspect game failure.
Do not depress the accelerator or brake pedal when turning on the game or switching to the Self-Test Mode. This will cause faulty program initialization and incorrect action of the player controls.
Table 1-3 Self-Test Procedure
Instruction Test Passes
- Without touching the pedals), set the self-test switch to the on position. Ali credits will be cancelled.
._ Press down on the accelerator pedal.
Press down on the brake pedal of the Sit-Down cabinet.
Turn the steering wheel clockwise, then counterclockwise.
. Shift the gear shifter.
. Shift the gear shift, press the auxiliary coin switch, and activate the coin switches.
. Press the auxiliary coin switch.
. To end the test, switch the self-test switch to off. Random symbols are displayed on the screen for about five seconds. The self-test display appears. RAMs and ROMs are tested. If the screen is different from the self-test dispiay, or if there are sounds, refer to Chapter 2, Self-Test Procedure.
The numbers to the right of ACCEL increase from 00 to somewhere between 90 and AQ as you press down on the pedal. If the test fails refer to Chapter 2.
The numbers to the right of BRAKE switch from 00 to FF. For the Upright cabinet, the numbers to the right of BRAKE should always read 00. If the test fails, refer to Chapter 2.
Rotating the wheei clockwise causes the numbers to the right of STEER- ING to increase. Rotating the whee! counterclockwise causes the numbers to decrease. If the test fails refer to Chapter 2.
The words to the right of SHIFT change from LO (shifter up) to HI (shifter down) as you shift gears. If the test fails, refer to Chapter 2.
The numbers to the right of SOUND increase from 00 to 20, and a new sound is played with each number. Test all 20 sounds. If the test fails, refer to Chapter 2.
Game statistics appear (for a few seconds) at the bottom of the screen. Press the coin switch each time you want to see the statistics. To erase game statistics, simultaneously press down on the accelerator pedal and press the auxiliary coin switch twice. Statistics will be reset at /999/. To reset the high-score table, simultaneously press down on the accelerator pedal and change gear shifter from low to high. The high-score table will bereset and contain fictitious scores.
1-10
Pole Position Set-Up Procedures
ALL RAMS GOOD ALL ROMS GOOD ACCELERATOR PEDAL RAM : aK sa ROM O fo BRAKE PEDAL
STEERING Et e WHEEL "+ S TEER ING 00. ‘SHIFT Lo ——_ GEAR SHIFTER 01 IN suns SOUND sans COINS 1COIN ‘CREDIT IN COIN2 4COIN A1CREDIT<————— sccuanicm QUALIFYING = LAP TIME NO. OF LAPS IN THE RACE
RACE bce LEVEL_—> EK TENDED RANK QUALIFYING LAP DIFFICULTY LEVEL (See Table 1-2)
GAME AUTOMATICALLY STARTS* (When correct number of Going are‘inger ted) THE COUNT STARTS AT 999(099) AND DECREASES. For example, if you play 10 games, the game subtracts 10 from 99.9, and the display shows 98.9 for the number of games ptayed, (Disregard decimal points.)
NO. OF GAMES PLAYED NO. OF POINTS SCORED (x10) NO. OF SECONDS PLAYED NOT APPLICABLE
—_—1 ———_— 999. 999. 999, 999. 999. 999. 999. 999. 999. 999, 999, 999, 999. 99. a a | | | | NO. OF SECONDS THAT GAME YA \ HAS BEEN POWERED ON NO. OF GAMES IN WHICH NO. OF GAMES IN WHICH PLAYER REACHED FINISH LINE PLAYER HAS QUALIFIED NO. OF GAMES THAT REACHED NO. OF GAMES THAT REACHED THIRD EXTENDED LAP j FIRST EXTENDED LAP “If screen displays MANUAL START, Suspect the game hamess. NO. OF GAMES THAT REACHED Refer to the Schematic Package. SECOND EXTENDED LAP
Figure 1-5 Self-Test Display
Set-Up Procedures
H. Game Play
Pole Position is a one-player game using a color raster-scan video display. The game action takes place at Fuji Speedway in Japan. The country around the speedway consists of green meadows, hills, and snow-capped Mt. Fuji. The player drives a Formula-1 race car on the Fuji Speedway. Player controls consist of a steering wheel, a two-position gear shifter, and accelerator and brake pedals on the Sit-Down cabinet (accelerator only on the Upright cabinet). The object of the game is to finish the qualifying lap as quickly as possible. If the player beats the clock, he qualifies for the Gran Prix at Fuji Speedway; if not, he drives out the remainder of his time along the qualifying course. As a qualifier, the driver is ranked according to his qualifying lap time, from position one (the pole position) to position eight. The player then races against the clock and other cars to finish the four laps (operator-selectable option) of the race as fast as possible and to achieve the highest score possible. The player earns points for passing cars, driving on the track, and finishing the race with time remaining. He is rewarded with an extended-play lap for completing a lap. Pole Position has four modes of operation: Attract, Play, High-Score, and Self-Test. Self-Test is a special mode for checking the game switches and computer functions. You may enter the Self-Test Mode from any other mode. However, all credits will be cancelled. Pole Position
ee eae
ae SS ee
- Attract Mode The Attract Mode begins when you set the power on/off switch to on or after the Play, High-Score, or Self-Test Modes. The Attract Mode ends when the correct amount of credit for a game is inserted or when the Self-Test Mode begins. When the Attract Mode begins, the game displays a picture with the words POLE POSITION flashing at the top of the screen. A map of Fuji Speedway is displayed in the center of the screen. Within the map are the words FUJ/ SPEEDWAY and 7 LAP 3459M. At the bottom of the screen is the copyright message. Then, the Attract Mode simulates game play. Eight Cars are at the starting line. The player's car, located in the eighth position, flashes on the screen. The starting lights flash from red to green and the race starts. The race continues until the player's car crashes into another car and explodes into a red bali of fire. Then, the car reappears on the screen and continues down the track until it hits a sign along the side of the road. Again, the car explodes. During this sequence, the message GAME OVER appears in the center of the screen. Finally, the Attract Mode displays the High-Score Table. The fastest lap time, average game speed, and prize winners appear at the top of the screen. Below this information is a list of the six highest scores. Opposite each score are the initials of the player who achieved that score.
- Play Mode The Play Mode begins when the correct amount of credit for a game is recorded. The game starts with the player's car behind the starting line and 90 seconds on the clock. (See Section E to select adifferent clock setting.) The car must finish the qualifying lap within 73 seconds to be in the race. If the player does not qualify, his car continues on the track until 90 seconds are used up.
Pole Position
Table 1-4 Qualifying Lap Information
POSITION QUALIFYING LAP TIME* BONUS POINTS
| 1 | 58” 50 | 4000 |
| 2 | 60" 00 | 2000 |
| 3 | 62" 00 | 1400 |
| 4 | 64" 00 | 1000 |
| 5 | 66" 00 | 800 |
| 6 | 68" 00 | 600 |
| 7 | 70” 00 | 400 |
| 8 | 73” 00 | 200 |
*In seconds and hundredths of a second The above times apply to manufacturer's recommended settings.
Just before the race begins, the player's car (flashing on the screen) is placed at the starting line with seven other cars. The position of the car depends on the qualifying time as shown in Tables 1-4 or 1-5. The starting lights flash from red to green, and the race begins. Racing hazards are other racing cars, sharp turns, and road signs. As the race progresses, more cars appear on the track. If the driver's car hits another car or a road sign, the driver's car is destroyed in an explosion. The driver's car reappears in a few seconds and the race continues. Driving through wet puddles or off the track slows down the driver's car. Racing into the first turn, the driver must let up on the accelerator slightly to make the corner. Road signs flash along the side of the track. Depending on how well the player manipulates the controls, he can either roar through the hairpin turns like a champion or spin out in a flaming crash. He jockeys for position with the other racers, while keeping his eye on the clock at the top of the screen. When his time runs out, the race is over. The top score achieved by a player appears at the top of the screen. The time alloted for the lap is displayed under the top score. increasing lap time {in seconds and hundredths of a second) and the speed of the car appears last. Set-Up Procedures
- High-Score Mode The High-Score Mode begins when a piayer has earned one of the 300 highest scores. The player has one minute to record his initials. A player rotates the Steering wheel to locate his initial. He presses a foot pedal to put his initial on the screen. The third time he presses the pedal his initials are transferred into the high-score table.
- Hints for Game Play
- Avoid puddles and the sides of the track because these slow you down. ¢ Accelerate and stay ahead of other racers.
- Stick to the inside of the track to make the corners.
- Successful completion of a turn depends on braking skill. © When sliding, steer into the skid.
Set-Up Procedures Pole Position
Table 1-5 Switch Settings for Qualifying Lap Times
SL Self-Test Level
| Option | Practice | of | Beat This Many Seconds |
| Switches | Rank | Difficulty | to Qualify tor Position: |
[ 1 2 3 1 2 3 4 5 6 7 8
| On Off On | F | Easy | 66 68 70 73 re) 77 80 82 |
| Off Off On | E | 65% 67% 7 72¥2 74¥e 76Ve 19 81 | |
| On On On | H | 59% 61 63 66 68 70 72 75 | |
| On On Off | oO | 59 61 63 65 67 69 71 74 | |
| Off On Off | c< | 58% 60 62 64 66 68 70 73 | |
| On Off Off | B | 58 60 62 64 66 68 70 72 | |
| Off Off Off | A | 57% = 59 61 63 65 67 69 71 | |
| Off On On | G | Hard | 57 59 61 63 65 &7 69 val |
4 Manufacturer's recommended settings
Table 1-6 Switch Settings for Racing Lap Times
| 9L | JA | Self-Test | Top Speed | Number of Seconds |
Option Option
| ‘Switches | Switch | Extended |
4 5 6 8 Goal Rank MPH KPH Lap1 Lap2 Lap 3 Lap 4 Off Off Off Off 3 A 195 313, 7 50 61 _ Off Off Off On 4 A 195 33 7 53 58 62 Off On Off Off 3 c 195 313 75 48 60 = Off On Off On 4 Cc 195 U3 5 51 87 61 On Off Off Off 3 B=" 195 313 75 46 59 = On Off Off On 4 Ba" 195 313 ri) 49 56 60 On On Off Off 3 D 196 313 75 44 58 > On On Off On 4 oO 195 313 75 47 55 59 Off Off On Off 3 E 225 360 15 48 60 = Off Off On On 4 E 225 360 7 St 57 61 On Off On Off 3 F 225 360 75 46 59 = On Ojf On On 4 F 225 0 75 49 56 60 Oif On On Off 3 G 244 391 i) 48 60 - Off On On On 4 G 244 391 rc} 51 57 61 On On On Off 3 H 244 391 75 46 59 _ On On On On 4 H 244 31 75 49 56 60 t “<Manufacturer's recommended settings “Upright cabinet **Sit-down cabinet
Self-Test Procedure
The reference designators for components in this chapter refer to games with Atari® PCBs. If you have Namco iN PCBs, please refer to CO-218-01.
The following self-test procedures should be performed by a qualified electronic technician. This game tests itself when the self-test switch is set to the on position. if there is a failure, the game produces audiovisual! aids to help you find the fail- / ing portion of the game. The self-test procedure in- —_—— cluded in Chapter 1 will help you decide if the game is working properly.
O ==
Chapter
Self-Test Procedure
A. Comments on Troubleshooting
When troubleshooting, first determine the symptom(s) of the failure. After determining the symptom, look over the wiring diagram and determine what assemblies could cause the failure. Could it be caused by the power supply, Regulator/Audio I! printed-circuit board (PCB), or the video display? The next step is to check all harness wires and connectors to the suspected assembly. If you do not find a harness or connector problem, substitute an assembly known to be good for the suspected failing assembly. If the game functions properly, you have successfully isolated the failure. If it doesn’t, repeat the procedure with another assembly. When you have isolated the failing assembly, you must troubleshoot that assembly and make the necessary repairs. If the video display fails, we suggest that a qualified video-display technician handle the troubleshooting and repair. Be sure to refer to The Book—A Guide to Electronic Game Operation and Servicing, published by Atari, Inc., whenever you need help with the techniques, tools, and terminology associated with coinoperated electronic games. To effectively troubleshoot a game PCB, learn as much as you can about the PCB. The diagrams in the Schematic Package (included with the game) show the functions of the circuitry. Again, while troubleshooting a PCB, first determine the symptom of the failure, then locate the suspected area on the schematic diagram. Tables 2-1 and 2-2 are troubleshooting aids, which can be used to locate faulty components.
Table 2:1 Locating Failed Components Pole Position
Table 2-2 Locating Failed Components on the CPU PCB
Custom AtoD
Symptom Area PROM IC RAM Converter
Audio Voice 9C 9D. Screech/Crash 9E Player's Motor 12E,12F All Other Sounds 71D TK 2d Inputs Brake and/or Accelerator a Steering 9K Option Switches 9K,9M All Other Inputs 9M Control for Audio & Inputs 8H,9H Syne 7M High Scores 7E
on the Video PCB
Symptom Area PROM Custom RAM
Large Car Pictures 120,130 Large Sign Pictures 12K,13K,12L, 43L ‘Smail Cars & Signs 12N,13N All Cars & Signs 12H,11N 13H 9F,10F Alphanumerics 7N,8M 8N Raceway 2L,2M,2N,4L 3N Background 6N,5K Raceway & Background 5L,6L Middle & Sides of Raceway 2B,2C,2D All Video 4D,7E,2F
Red NE
Green 11D Blue 1c
2-2
B. Performing the Self-Test
This game will test itself and provide data to show that the game’s circuitry and controls are operating properly. The data is provided on the video display and speaker. No additional equipment is necessary. Video game repair should only be performed by a qualified electronic technician. To begin the Self-Test Mode, set the self-test switch, which is located on the utility panel, to the on position.
Do not depress the accelerator or brake pedal when turning on the game or switching to the Self-Test Mode. This will cause faulty program initialization and incorrect action of the player controls.
Pole Position
SELF-TEST SCREEN 1—Test Passes: Upright Cabinet. If the test passes, the screen displays the picture in Figure 2-1, Upright Test Passes. See Chapter 1, Section G, Performing the Initial Setf-Test for a complete description of this picture. To see self-test screen two, set the self-test switch to off and immediately back to on.
Figure 2-1 Self-Test Screen 1: Upright Test Passes
Sit-Down Cabinet. if the test passes, the screen displays the picture in Figure 2-2, Sit-Down Test Passes. See Chapter 1, Section G, Performing the Initial Self-Test for a complete description of this picture. To see self-test screen two, set the self-test switch to off and immediately back to on.
SOUND =
COINL ZCOINS iCREDIT
z CREDIT
PRACTICE. AUTO STAR
Figure 2:2 Self-Test Screen 1: Sit-Down Test Passes Self-Test Procedure
SELF-TEST SCREEN 1—Test Fails: If the test fails, the screen may display the picture in Figure 2-3, Test Fails.
Figure 2-3 Self-Test Screen 1: Test Fails
ROM failure is indicated by the word ROM anda pair of alphanumeric characters displayed at the top of the screen.
Table 2-3 Locating the Failed ROM
Location on Location on ROM No. ATARI CPU PCB NAMCO CPU PCB
| 0 | 7H | 6H |
| 1 | 7F | 5H |
| 2 | 3t | 8M |
| 3 | 4l | BL |
| a | 3K | 7M |
| Ss | 4K | 7L |
| 6 | 3E | 4M |
| 7 | 4E | 4 |
| 8° | 3D | 3M |
| o | 4D | 3L |
“Not used
Self-Test Procedure
RAM failure is indicated by the word RAM and a pair of alphanumeric characters displayed at the top of the screen. Table 2-4 lists the failed RAM chip, the printed-circuit board (PCB) the chip is on, and the chip’s location. Replace the failed RAM, and restart the test (set the self-test switch to off, and then to on).
Table 2-4 Locating the Failed RAM
Location on Location on
ATARI NAMCO
RAM No. CPU PCB Video PCB CPU PCB Video PCB
| 0, 20, 40 | 8F | 7H |
| 4,21, 41 | 7F | 7F |
| 22, 42 | a | SH |
| 23, 43 | 7 | oF |
| 2, 24, 44 | 8H | 6H |
| 3, 24, 45 | 7H | 6F |
| 26, 45 | 8K | 4H |
| 27,47 | 7K | 4F |
| 4, 28, 48 | 3F | 7B |
| 29, 49 | ar | 7 |
| 5, 30, 50 | 3E | 8B |
| 31, 51 | 4E | 8c. |
7s TH 7 7K 8H 8 7E 4H
Steering failure is indicated by failure of the numbers to the right of STEERING to properly increase or decrease. As you rotate the wheel clockwise, these numbers should increase; as you rotate the wheel counterclockwise, they should decrease. If the test fails, suspect the Coupler PCB.
Accelerator failure is indicated by failure of the numbers to the right of ACCEL to increase as you press down on the pedal. If no numbers appear, suspect a bad A-D converter on the CPU PCB ora mechanical problem on the foot pedal assembly. Troubleshoot using the information in Chapter 3, Section B, and the game schematics.
2-4 Pole Position
Brake failure on the Sit-Down cabinet is indicated by failure of the numbers to the right of BRAKE to change as you press down on the brake pedal. On the Upright cabinet, brake failure is indicated by anything other than 00 appearing to the right of BRAKE. If the test fails, suspect a bad switch, improper mechanical adjustment on the foot pedal assembly, or no ground on the brake edge-connector pin in the harness. Gear-shifter failure is indicated by failure of the words to the right of SHIFT to change from LO (shifter up) to H/ (shifter down) as you shift gears. If the test fails, suspect loose connector wires or abad switch. Sound failure is indicated by the absence of any sound when the coin switches or gear shifterare activated. Suspect a loose harness or connector wire, the volume control turned off, the custom audio I/O chip, or the Regulator/Audio It board. Troubleshoot using the game schematics. To see self-test screen two, set the self-test switch to off and immediately back to on.
SELF-TEST SCREEN 2: A white crosshatch pattern appears on the screen (see Figure 2-4). Use this pattern for convergence (see the raster-scan video display manual).
a
Figure 2-4 Self-Test Screen 2
Maintenance, Repair, and Parts
This chapter details maintenance and repair information and provides information you need to order Parts for your game. Common hardware (screws, nuts, washers, boits, etc.) has been deleted from most of the parts lists. However, a parts list for the hardware to mount the printed circuit boards (PCBs) to the cabinet has been included. The printed circuit board (PCB) parts lists are arranged in alphabetical order by component. Each component subsection is sorted by reference designator. Other parts lists are arranged alphanumerically by Atari part number. In these parts lists, all A-prefix numbers come first. Following these are numbers in sequence evaluated up to the hyphen, namely 00- through 99-, then 000598-through approximately 201000-. When ordering parts, please give the part number, part name, number of this manual, and serial number of your game. This will aid in filling your order rapidly and correctly. We hope the results will be less downtime and more profit from your game. Atari Customer Service numbers are listed on the inside front cover of this manual.
En nOP oda as east
Maintenance, Repair, and Parts
A. Cabinet-Mounted Assemblies
Fluorescent Tube and Speaker See Figures 3-11 & 3-12
78-6900404 (Tape)
7@-6900402 (Tape)
039417-01 (Display shield)
78-6900402. (Tape) N Steering-Wheel Control Assy. See Figure 3-5
178034-024 (T-Moiding)
Utility Panel See Figure 3-15
Coin Door Assy. See Figures 3-16 & 3-17 038870-01 (Coin box enclosure—& not shown) 036091-01 (Coin box—not shown)
78-3201 (Glide)
3-2 Pole Position
Manuals, Schematics, & Self-Test Label— See parts list on next page
Deflection PCB used with Atari Display—see display manual
003053-01 (Retainer) 03733201 | (Ventilation grille)
SY
039371-01 (Shield retainer) A038881-01
| A037701-01 | ——] | (Lock) | |
| see | Fi EMI Cage | (hocess panel | |
| ee | Figures 3-18 & 3-23 | 5 | 03937601 i |
Video Display (Access panel) See Figure 3-14 A040512-01 (Gna one) xhaust du ; (Fan harness assy.) apr 2 Deflection PCB (Fan & bracket assy.) eN —\Y 178114-032 s onto UF Decteececah a, (Bracket) CO Game PCB Assy. See Figures 3-18, Gear-Shifter Control Assy. eebe son See Figure 3-8 A039459-xx i (Main harn. assy.) Control Panel Assy. A039499-01 See Figures 3-3 & 3-4 (Main harn. assy.) Regulator/Audio Il 148001-001 PCB Assy. an pee
@ (Caster)
‘A039460-01 Z ‘Power harn. 258y) _/pqwer Suppie eS See Figure 3-24 — A037453-04 037243-01 (Power cord) (Base plate) ‘A037454-04 A039353-xx (Power cord) s7e0da02s (Cabinet assy.) 03747001 (T-Molding) A039353-02 (On/otf switch assy.) (Cabinet assy) 009992.01 (<< Foot-Pedal Assy. See Figure 3-9 (On/ott switch cover)
Figure 3-1 Cabinet-Mounted Assemblies US-Built Upright Cabinet A039352-01 S lreland-Built Upright Cabinet A039352-02 S
Pole Position Maintenance, Repair, and Parts
Cabinet-Mounted Assemblies U.S-Built Upright Cabinet lreland-Built Upright Cabinet Parts List
Assemblies and components in the following parts list are shown in Figure 3-1.
Part No. Description For U.S-Built Upright Cabinet
| A037453-04 | Strain-Relief Power Cord | (U.S. and Canada) |
A037701-01 Electromagnetic interference Cage (includes glides)
| A039353-01 | Cabinet Assembly | (includes glides and PCB retainers, but not the rear access panel) |
A039459-01 Main Harness Assembly (for Atari PCBs) A040512-01 Fan Harness Assembly
| A040547-02 | Fan and Bracket Assembly | Acceptable substitute is part no. A040547-01 |
038641-01 Speaker Grille (not shown)
| 040564-01 | Door Panel Grille | (not shown) |
040565-01 €xhaust Duct
| 178114-032 | 2-Inch Plastic Tape | (20 inches required) |
For Ireland-Built Upright Cabinet
| A037454-04 | Strain-Relief Power Cord | (Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece, |
Indonesia, Italy, Netherlands, Norway, Spain, Sweden, and Uruguay)
| A039353-02 | Cabinet Assembly | (includes glides and PCB retainers, but not rear access panel—for NAMCO PCB) |
| A039353-03 | Cabinet Assembly | (includes glides and PCB retainers, but not rear access panel—for Atari PCB) |
| A039459-02 | Main Harness Assembly | (for Atari PCB) |
| A039499-01 | Main Harness Assembly | (for NAMCO PCB) |
037742-01 Printed Circuit Board Mounting Bracket (not shown) 039119-02 Rear Access Panel 72-1620S #6-32 x 1.25-inch Pan Head Machine Screw 78-016S #6 Flat Washer For US-Built and Ireland-Built Cabinets A037470-01 Power On/Off Switch/Mounting Plate Assembly A038881-01 Lock Assembly (forrear access panel) Acceptable substitute is part no. A038881-03 A039420-01 Dashboard Housing and Decal Assembly A039460-01 Power Harness Assembly A039576-01 Coin Option Interconnect Assembly The following nine items are the technical information supplements to this game:
| CO-218-01 | Pole Position Supplement | (for NAMCO game PCB removal) |
SP-218 Pole Position Schematic Package (for Atari PCB) SP-219 Pole Position Schematic Package (for NAMCO PCB) $T-218-01 Pole Position Label with Self-Test Procedure and Option Switch Settings (for Atari PCB) ST-219-01 Pole Position Label with Self-Test Procedure and Option Switch Settings (for NAMCO PCB) TM-160 Service Manual for 19-Inch Electrahome Color Raster-Scan Display (use with part no. 92-049), or TM-199 Service Manual for 19-Inch Atari Color Raster-Scan Display (use with part no. A200001-01), or TM-221 Service Manual for 19-Inch Matsushita Color Raster-Scan Display (use with part no, 139003-1004) TM-218 Pole Position Operation, Maintenance, and Service Manual
3-3
Maintenance, Repair, and Parts Pole Position
Cabinet-Mounted Assemblies U.S-Built Upright Cabinet lreland-Built Upright Cabinet Parts List, continued
Part No. Description
| 75-5124B | #10-24 x 1.50-Inch Carriage Bolt | (for mounting dashboard) |
78-3201 Adjustable Glide 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, ¥-Inch Wide x %-Inch Thick (48 inches required—use on top edge of video display shield, and on top edge of control panel) 78-6900404 Vinyl Foam Single-Coated Adhesive Tape, ¥-Inch Wide x %4-Inch Thick (48 inches required—used on top and bottom of attraction glass) 003053-01 Attraction Glass Retainer 009992-01 On/Off Switch Cover 037243-01 Base Plate for Power Supply 037332-01 Ventilation Grille 038091-01 Molded Coin Box (not shown) 038770-01 Metal Coin Box Enclosure (Acceptable substitute is part no. 038781-01—not shown) 039144-01 Speaker Grille 039371-01 Video Display Shield Retainer 039376-01 Rear Access Panel (does not include lock) 039417-01 Video Display Shield with Graphics 148001-013 6- x 9-Inch Oval, 4-Ohm, 6-Ounce Shielded High-Fidelity Speaker (located on front panel)
176015-110 #10 x %-Inch Cross-Recessed Pan-Head Tapping Screw (for mounting speakers)
| 178034-024 | %-Inch Black Plastic Molding | (located on side panels) |
| 178034-025, | 254.-Inch Black Plastic T-Molding | (located on front panel) |
178048-001 2-Inch Rigid Caster
Maintenance, Repair, and Parts Pole Position
DR 4039465-02 03910101
| A040514-01 | (Main harn. assy.) | (Cabinet assy.) |
| (Fan harness assy.) | A039465-01 | A039101-02 |
| 171002-001 | (Main harn, assy) | (Cabinet assy) |
| « cue fan) | A039245-01 | A039101-03 |
103-001
| ranbade guard) | (Main harn. assy.) | (Cabinet assy.) |
A03701-01 Game PCB Assy. Eee See Figures 3-18, 3-19 & 3:20 j 2034.0: 178034.034 318 & 323 a | (T-Molding)
o 148001-013 038641-01 : : (Vent. grille) pecker} 148001-001 039145-01 (Speaker) (Speaker grille) 039144-01 (Grille)
A038881-01 178034-024 (Lock) (T-Molding)
038641-01 (Vent. grille)
Utility Panel See Figure 3-15
NS Power Supply Assy. ™ See Figure 3-24
A037470-01 A039246-01 (On/off switch assy.) (Power harn. assy.) 009992-01 (On/oft switch cover) A037453-03 (Power cord) A037454-03 (Power cord)
Figure 3-2 Cabinet-Mounted Assemblies US-Built Sit-Down Cabinet A039100-01 R lreland-Built Sit-Down Cabinet A039100-02 R
3-5
Maintenance, Repair, and Parts Pole Position
Manuals, Schematics, & Self-Test Label— See parts list on next page
Gear-Shifter Control Assy. See Figure 3-8 ay Video Display See Figure 3-14 Steering-Wheel Control Assy. See Figure 3-5 037086-01 (Front window retainer)
78-6900804 (Tape)
039141-01 (Front window)
Control! Panel Assy. See Figures 3-3 & 34
039148-01 (Display shield/graphics)
Coin Door Assy. ys) See Figures 3-16 & 3-17 FootPedal Assy. See Figure 3-9 036870-01 (Coin box exclosure)
178023001 a (Caster) b 78-3201 (Glide)
Figure 3-2 Cabinet-Mounted Assemblies, continued US-Built Sit-Down Cabinet A039100-01 R Ireland-Built Sit-Down Cabinet A039100-02 R
3-6
Pole Position Maintenance, Repair, and Parts
Cabinet-Mounted Assemblies Sit-Down Cabinet Parts List
Assemblies and components in the following parts list are shown in Figure 3-2,
Part No. Description
For U,S-Built Cabinet
| A037453-03 | Strain-Relief Power Cord | (U.S. and Cunada) |
A037701-01 Electromagnetic Interference (EMI) Cage (includes guides)
| A039101-01 | Cabinet Assembly | (includes glides and PCB retainers, but not the rear access panel) |
A039465-01 Main Harness Assembly A040514-01 Fan Harness Interconnect Assembly 171002-001 110 V Exhaust Fan 178093-001 Fan Blade Guard
For treland-Built Cabinet
| A037454-03 | Strain-Relief Power Cord | (Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece, |
Indonesia, Italy, Netherlands, Norway, Spain, Sweden, and Uruguay)
| A039101-02 | Cabinet Assembly | (includes glides and NAMCO PCB retainers, but not the rear access panel) |
| A039101-03 | Cabinet Assembly | (includes glides and Atari PCB retainers, but not the rear access panel) |
| A039245-01 | Main Harness Assembly | (for NAMCO PCBs) |
A039465-02 Main Harness Assembly (for Atari PCBs) 037990-01 Ventilation Grille (on rear access panel} For US-Built and treland-Built Cabinets A039246-01 Power Harness Assembly A037470-01 Power On/Off Switch/Mounting Plate Assembly A038881-01 Lock Assembly (for rear access panel) Acceptable substitute is part no. A038881-03 107001-007 Flat Black Paint The following nine items are the technical information supplements to this game:
| CO-218-01 | Pole Position Supplement | (for NAMCO game PCB removal) |
SP-218 Pole Position Schematic Package (for Atari game PCBs) SP-219 Pole Position Schematic Package (for NAMCO game PCBs)
| ST-218-01 | Pole Position Label with Self-Test Procedure and Option Switch Settings | (for Atari PCBs) | |
| ST-219-01 | Pole Position Label with Self-Test Procedure and Option Switch Settings | (for | NAMCO PCBs) |
TM~60 Service Manual for 19-Inch Electrohome Color Raster-Scan Display (use with part no. 92-049) TM-201 Service Manual for 19-Inch Wells-Gardner Color Raster-Scan Display (use with part no. 92-055) TM-218 Pole Position Operation, Maintenance, and Service Manual TM-220 Service Manual for 19-Inch Matsushita Color Raster-Scan Display (use with part no. 139003-1004) 78-3201 Adjustable Glide
| 78-6900402 | Vinyl Foam Single-Coated Adhesive Tape, V4-Inch Wide x %-Inch Thick | (72 inches required; |
used on front window)
| 78-6900804 | Vinyl Foam Single-Coated Adhesive Tape, Y2-Inch Wide x Ya-Inch Thick | (24 inches required; |
used in top s/ot of video display cleat) 002728-01 Controi-Panel Mounting Bracket
Maintenance, Repair, and Parts Pole Position
Cabinet-Mounted Assemblies Sit-Down Cabinet Parts List, continued
Part No. Description
009992-01 On/Off Switch Cover 035851-01 Top Panel Hinge 037086-01 Front Window Retainer 037742-01 Printed Circuit Board Mounting Bracket 038091-01 Molded Ccin Box (not shown) 038641-01 Ventilation Grille (on rear access panel) 038870-01 Metal Coin Box Enclosure Acceptable substitute is part no. 038781-01 039141-01 Front Window
039144-01 Speaker Grille (not shown—/ocated behind seat) 039145-01 Speaker Grille (located under control panel) 039148-01 Video Display Shield with Graphics 039155-01 Metal Attraction Panel with Graphics 148001-001 6- x 9-Inch Oval, 4-Ohm, 15 W Unshielded High-Fidelity Speaker (not shown—located behind seat) 148001-013 6- x 9-Inch Oval, 4-Ohm, 15 W Shielded High-Fidelity Speaker (located under control panel) 171034-xxx Over/Under Coin Door Assembly Acceptable substitute is part no. 171027001 176015-110 #10 x %-Inch Cross-Recessed, Pan-Head Tapping Screw (not shown—for mounting speakers/grilles to seat back) 178034-024 34-Inch Black Plastic T-Molding 178034-034 1-Inch Black Plastic Molding (located on seat back) 178023-001 4-Inch Rigid Caster
3-8
Pole Position
B. Player Controls
Opening the Control Panel:
1. Unlock and open the rear access panel (see Figure 33), Reach through the opening to the top of the control panel. Remove the hardware that secures the control panel to the game cabinet.
Guide or pull the control panel forward to its resting position. The steering wheel and gear shifter are now accessible for maintenance or repair (see Figure 3-4). Make sure the foam tape is in good condition. This tape is on the control panel of the Upright cabinet, and ‘on the display shield for the Sit-Down cabinet. Reassemble in reverse order.
Figure 3-3 Control Panel
3-9
Maintenance, Repair, and Parts
any parts on the panel, make sure that wire is firmly attached to the inside of Panel.
A039411-01 (Control panel/decal) 039373-01 (Control panel) 039409-04 (Decal) 177012-111 (Spring nut)
~ 75-5524B (Carriage bolt)
A039108-01 A (Control panel/decal) 039143-01 (Control pane!) 039153-04 (Decal)
Assemblies A039107-01 and A038412-01 are used with Atari game PCBs; Assemblies A039107-02 and A039412.02 are used with Namco game PCBs.
3-10 Players may receive an electrical shock if this control panel is not properly grounded! After servicing
Gear-Shifter Control Assy. Pole Position
72-JB3814S = (Screw) the ground the control ? —- been | (Washer) J See Figure 3-6
95-935 177010-244 (Wing nut) (Hex locknut)
75-07002 (Flat washer) 75-045S (Washer)
(Spacer)
177010-244 (Locknut)
(Spacer)
; 4
L_ 75-5512B (Carriage bolt) NY 75-5528B (Carriage bolt) »~ ‘A039229.01 ‘Steering-Wheel Control Assy. See Figure 3-5
Figure 3-4 Control Panel Assembly Upright Cabinet A039412-01 E Sit-Down Cabinet A039107-01 E
Pole Position Maintenance, Repair, and Parts
Control Panel Assembly Parts List
Assemblies and components in the following parts list are shown in Figure 3-4.
Part No. Description
Upright Cabinet A039411-01 Control Panel with Decal (consists of control panel 039373-01 and decal 039409-04) 75-5524B #%-20 x 1.5-Inch Black Carriage Bolt 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, Y-Inch Wide x ¥%-Inch Thick (96 inches required) 177012-111 %2-\nch Push-On Spring Nut Sit-Down Cabinet A039108-01 Control Panel with Decal (consists of contro! pane! 039143-01 and decal 039153-04) 75-035S Ya-Inch Wide Flat Washer 75-5528B #¥%-20 x 1.75-Inch Carriage Bolt 039132-01 Control Panel Spacer Upright and Sit-Down Cabinets A039229-01 Steering-Wheel Control Assembly (Namco games use part no, A039229-02) A000608-09 Gear-Shifter Control Assembly 72-JB3814S #8-16 x 0.87-Inch Screw 75-935 #%-20 Wing Nut 75-045S Y4-Inch Split-Lock Washer 75-07002 Ya-Inch Flat Fender Washer (not shown) 75-5512B #¥s-20 x 0.75-Inch Black Carriage Bolt 005255-04 Shifter Bezel 039154-01 Shifter Spacer 175002-004 #10 Flat Washer 177010-244 #¥%-20 Hex Locknut
Maintenance, Repair, and Parts
a Pole Position
039243-01 (Label) 178099-003 ‘Steering wheel)
039230-01 (Steering cap)
039231-01 (Shaft)
175003-002 (Nylon washer) 178012-002 eect (Retaining ring) . 039234-01
72-HB3606S (Hex screw) —_,. 75-018S (Washer)
A040510-01 178100-001 (Coupler PCB assy.) (Flange bearing) 178097-001 (Bearing assy) a7e002001 178118-001 (Washer) (Sleeve bearing) ———__| 175009-170 (Nylon washer) 178012-003 040264-01 (Encoder shaft) 178101-002 RS (Retaining ring)
178101-001 (Gear)
175002-002 (Heavy washer) (Gear) ee Sink: 039232-01 | (Spacer) 75-040 (Washer) 035938-01 (Encoding wheel) 72-8008 (Screw) 75-07014 vodeL 75.044 (Washer) = NYOGEL 779 (Split-lock washer) ee 72.8408, (Screw) = SIN-ONE OIL
Figure 3-5 Steering-Wheel Control Assembly A039229-01 H ‘See text for lubrication information.
3-12
Pole Position Maintenance, Repair, and Parts
Steering-Wheel Control Assembly Parts List
Assemblies and components listed in the following parts list are shown in Figure 3-5.
Part No. Description
A040510-01 Coupler Printed-Circuit Board Assembly (includes Radial Optical Coupler) 72-8008 #10-32 x 0.50-Inch Steel Socket-Head Cap Screw 72-8012 #10-32 x 0.75-Inch Stee! Socket-Head Cap Screw 72-8408 #4-40 x 0.50-Inch Steel Socket-Head Cap Screw 72-HB3606S #6-32 x 0.38-Inch Zinc-Plated Steel Hex Washer-Head Screw 75-018S #8 Flat Washer 75-0408 #10 Split-Lock Washer 75-044S #4 Split-Lock Washer 75-07014 #4 Flat Washer 79-58356 4-Position Connector with Locking Ramp (located on the Coupler PCB Assembly) 030369-01 Radial Optical Coupler (located on the Coupler PCB Assembly) 035221-01 1002, +5%, %4W Resistor (located on the Coupler PCB Assembly) 039230-01 Steering Cap 039231-01 Steering Shaft 039232-01 Spacer 040264-01 Encoder Shaft Acceptable substitute is part no. 039233-01 039234-01 Steering Frame 039243-01 Steering Cap Label 035938-01 Encoding Wheel 107013-001 3-in-One® Oil 175002-001 Fiat Washer 175002-002 #10 Heavy Flat Washer 175009-170 Nylon Flat Washer 178012-001 Retaining Ring for 0.75-Inch Shaft 178012-003 Retaining Ring for 0.25-Inch Shaft 178027-001 Nyogel 779 Lubricant 178097-001 Bearing for 0.25-Inch Shaft 178099-003 Steering Wheel 178100-001 Bearing Flange for 0.75-Inch Shaft Acceptable substitute is part no. 040243-01 178101-001 24 Diametral Pitch x 20° Pressure Angle x 2.500 Pitch Diameter Spur Gear 178101-002 24 Diametral Pitch x 20° Pressure Angle x 0.583 Pitch Diameter Spur Gear 178118-001 Ye-Inch x Va-Inch Sleeve Bearing
Maintenance, Repair, and Parts
Before you remove or repair any player control, tum the game off.
Removing the Coupler PCB, Encoding Wheel, and Steering Wheel:
- Open the control panel (see Figure 3-3).
- To remove the steering-whee!l control assembly, disconnect the green ground wire from the grounding hardware. Remove the hardware which secures the steering-wheel controi assembly to the control panel (see Figure 3-4), Pole Position
Unplug the harness connector on the Coupler PCB. To remove the Coupler PCB, remove the hardware securing the PCB to the steering frame. To remove the encoding-wheel assembly, hold the shaft of the encoding wheel in a fixed position with a wrench. Use an Allen wrench to remove the cap screw, encoding wheel, washers, spacer, and bearing. To remove the encoder shaft, pry off the retaining ring. To remove the steering wheel, hold the steering wheel shaft in a fixed position. Remove the cap screw, washers, and gear. Pry off the retaining ring and remove the heavy washer. Reassemble in reverse order.
OPEN-END WRENCH ALLEN WRENCH
ENCODING WHEEL
Figure 3-6 Steering-Wheel Control Screw Adjustment
3414
Pole Position
Lubricating the Steering-Wheel Control:
Periodic maintenance of the steering-wheel control assembly must include the following procedures: 1. Check that the #4-40 x ¥2-inch socket-head cap screw (part no. 72-8408) on the encoder shaft is secure (see Figure 3-6). lf the screw needs tightening, hold the encoder shaft (part no. 039233-01) with a %,inch openend wrench while tightening the screw with a %,-inch Allen wrench. Check that the #10-32 x ¥2-inch socket-head cap screw (part no. 72-8008) on the steering-wheel shaft is tight (see Figure 3-5). \f the screw needs tightening, hold the steering wheel still while using a %-inch Allen wrench to tighten the screw. Check, and if necessary, lubricate the encoder shaft (part no. 039233-01) and the two flat nylon washers {part no. 175003-002) as shown in Figure 3-5. Use ONLY the recommended lubricant, Nyoge! 779 (part no. 178027-001). Nyogel 779 is a damping grease and will aid in the smooth operation of the control. Make sure a HEAVY film of this lubricant is applied to the encoder shaft and both surfaces of the nylon washers. Check for a grinding feeling caused by inadequate !ubrication or by the gears being too close together. To correct this condition, lubricate with Nyoge! 779, and/or loosen the locknut on the bearing assembly
STEERING-WHEEL CONTROL Maintenance, Repair, and Parts
(part no. 178097-001) and move the bearing away from the main steering shaft toward the coupler PCB assembly. This movement may be very small, but it can make a difference. Check, and if necessary, lubricate the bronze flange bearings (part no. 178100-001) in the steering frame (part no. 039234-01), using a few drops of a light machine oil, such as 3-in-One oil (part no. 107013-001) (see Figure 3-5). The steering-wheel control assembly should be positioned as follows (see Figure 3-7): a. Open the control panel. b. Disconnect the green ground wire from the grounding hardware. Remove the four carriage bolts that secure the steering-wheel control assembly to the control panel. c. Rotate the steering-wheel control assembly 90° so that the encoding wheel assembly and the encoder shaft are on the bottom (nearest the floor). All new Pole Position games will be assembled in this manner. d. Reinsert the four carriage bolts that secure the steering-wheel control assembly to the control panel. Reconnect the green ground wire.
COUPLER PCB
GEAR-SHIFTER CONTROL
CONTROL PANEL
Figure 3-7 Steering-Wheel Contro! Orientation
Maintenance, Repalr, and Parts Pole Position
005255-04 OD (Bezel) \
ye See text for lubrication information.
A000610-02 (Shifter handle assy.)
039705-01 (Spring)
76-11375S (Ball bearing) 000609-02 (Shift housing)
an 72-1412S (Screw) 65-0218 (Switch) (Shift detent)
75-9445, NN (Hex nut) 035301-02 (Actuater pin)
Figure 3-8 Gear-Shifter Control Assembly A000608-09 AD
3-16
Pole Position
Before you remove or repair any player control, turn the game off.
Removing the Gear-Shifter Control Assembly: Open the control panel (see Figure 3-3). Maintenance, Repair, and Parts
- To remove the switch, remove the two screws and locknuts that secure the switch to the housing. Be careful not to lose the small actuator pin that sits above the switch actuator.
- Reassemble in reverse order.
- To remove the gear-shifter control assembly (see Lubricating the Gear-Shifter Control: Figure 3-4), disconnect the plug-in connectors from shi
gear-shifter control assembly to the control panel. control assembly using the procedure above. Apply a light-
- To open the gear-shifter assembly, remove the six duty lubricant (such as Nyogel 779) every six months to the screws that secure the two halves of the housing (see spherical part of the handie and the detent. Figure 3-8).
Gear-Shifter Control Assembly Parts List
Assemblies and components listed in the following parts list are shown in Figure 3-8.
Part No. Description
A000610-02 Gear-Shifter Handle 65-021A Single-Pole Single-Throw Low-Force Miniature Switch 72-JB3606 #6 x 0.38-Inch Steel Plastite Screw Acceptable substitutes are part nos. 72-JB3608, 72-JA4608, and 72-JB1606B 7214128 #4-40 x 0.75-Inch Cross-Recessed Pan-Head Steel Machine Screw
75-944S #4-40 Self-Locking Polymer Hex Nut 78-3002003 Spring 000609-02 Gear-Shifter Housing (two required) 005255-04 Shifter Bezel 035792-01 Shift Detent 035301-02 Actuator Pin 178027-001 Nyogel 779 Lubricant (not shown)
Maintenance, Repair, and Parts Pole Position
On . 039241.01 Z (Safety tread) ‘See text for lubrication information.
039240-01 039236-01 (Foot pedal-—accelerator) (Pivot pin)
v
(Retaining ring) 040028-0 fe (Compression spring) <
039242-01 (Cable)
039238-01 (Pulley)
039704-01 ‘ (Extension spring) | : +. (Cap screw)
é Cap screw of pulley must be In this position when pedal is fully ‘open (at rest). 03970301 : : (Cabie spring) 039230-01 y (Base plate) SS 72-HB3410S* (Screw) 19-9026 (Potentiometer) 160023-001* (Switch)
“For Sit-Down cabinet (dual foot-pedal assembly)
**For Upright cabinet (single foot-pedal assembly)
'039142-01° oe Mounting plate) SS . 177010-244 039379-01 (Hex locknut) (Mounting plate)
4 = NYOGEL 778 75-050B As (Washer) —_—_r?e = WD-40
Figure 3-9 Foot-Pedal Control Assembly
3-18
Pole Position Maintenance, Repair, and Paris
Foot-Pedal Control Assembly Upright A039413-01 F Sit-Down A039109-01 E Parts List
Assemblies and components in the following parts list are shown in Figure 3-9.
Part No. Description
Sit-Down Cabinet A039247-01 Dua! Foot-Pedal Control Harness Assembly 72-HB3410S #4-40 x 62-Inch Thread-Forming Hex Screw 039142-01 Dual Foot-Pedal Contro! Mounting Plate 160023-001 SPOT Snap Switch with Actuator Upright Cabinet A039463-01 Single Foot-Pedal Control Pedal Harness Assembly 75-035S Ya-Inch Flat Washer 75-5520B #%4-20 x 1.25-Inch Black Carriage Bolt. (not shown) 75-915S #%-20 Hex Nut 039379-01 Single Foot-Pedal Control Mounting Plate Upright and Sit-Down Cabinets
| 19-9026 | 5kQPotentiometer | (Acceptable substitute is part no. 19-9022) |
72-8606 #6-32 x 0.38-Inch Hex Socket-Head Cap Screw 75-050B #10 Internal-Tooth Lock Washer 039236-01 Pivot Pin 039238-01 Pulley 039239-01 Foot-Pedal Control Base Plate 039240-01 Foot-Pedal Control Accelerator 039241-01 Adhesive Transfer Tape (safety tread)
039242-01 Cable
| 039703-01 | Extension Spring | (for cable) |
| 039704-01 | Extension Spring | (for pedal) |
| 040028-01 | Compression Spring | (for pedal) |
107012-001 Dry Teflon Spray Lubricant (not shown) 177010-244 #¥%4-20 Hex Locknut 178012-004 External Retaining Ring for %-Inch Diameter Shaft
3-19
Maintenance, Repair, and Parts Pole Position
Foot-Pedal Control Maintenance:
1. tings are correct, perform the maintenance Unlock and open the rear access panel. Reach through procedures set out below. : the opening to the top of the foot-pedal control.
- Remove the two locknuts located on the top two footpedal mounting screws. Periodic maintenance of the foot-pedal controls must in- t
- From the front of the Upright cabinet or in the player clude the following procedures: area of the Sit-Down cabinet, remove the foot-pedal 1. The only maintenance required on this newly designmounting screws and lift out the foot-pedal control ed foot-pedal control is lubrication every four months assembly. (see Figure 3-9). Lubricate the pivot pin and surround-
- Place the foot-pedal contro! assembly upside down on a work surface in front of you with the pedal in a fully open position and the hinged end away from you.
CAP SCREW CABLE
- Rotate the pulley until the cap screw
- Wrap the cable one quarter-turn Points straight up. around the pulley and bring it out through the notch toward the cap screw. PULLEY
- Thread the cable up through the
- Hook the larger eyelet of the cable to opening in the base plate. the foot-pedal bracket.
LARGER EYELET 7 VR BRACKET
Figure 3-10 Foot-Pedal Pulley Cable Rewinding
3-20
Pole Position
ing area, the spring cable, and pulley with dry teflon Spray. If needed, apply a light-duty lubricant like WD-40 to the potentiometer shaft only.
- \f your accelerator pedal fails to return to its uppermost position, check for the following conditions: Maintenance, Repair, and Parts
If the pulley cable needs rewinding, adjust as shown in Figure 3-10.
| a. | inadequate lubrication of the pedal assembly. Lu- | If it is necessary to disassemble the foot-pedal |
bricate as necessary. control assembly and remove the pulley cable
| b. | A broken extension spring (part no. 039704-01). | (part no. 039242-01), MAKE SURE the cable is |
Replace if necessary. wound as illustrated in Figure 3-10, BE
| c. | A broken or inadequately lubricated compression | CAREFUL not to cut or fray the cable in the |
spring (part no. 000592-01). Replace andlor lubri- disassembly/assembly process. Note that the cate if necessary. foot-pedal assembly must be removed from the an . game cabinet in order to wrap the cable cor-
| d. | Inadequate lubrication of the potentiometer shaft | rectly. |
(part no. 19-9026). Lubricate as necessary with a light-duty lubricant, such as WD-40 (part no. 78-1701).
Wrap the cable twice around the cap screw in a clockwise direction.
- Attach the smaller eyelet on the cable to the cable spring. NOTE: You may find it helpful to compress the base plate slightly and extend the cable spring during this step.
- Bring the cable back through the notch and wrap it around the pulley one and one-half times.
CABLE SPRING
SMALLER EYELET
Figure 3-10 Foot-Pedal Pulley Cable Rewinding, continued
3-21
Maintenance, Repair, and Parts
C. Fluorescent Tube and Speaker Replacement
Upright Cabinet Removing the Tube and Speaker Board:
- From the back of the game, unlock and open the rear access panel. Unplug the tube and speaker’s 5-pin harness connector (see Figure 3-11).
- From the front of the game, remove the three buttonhead screws and lock washers that secure the upper attraction-panel retainer to the cabinet. Loosen the screws and washers that secure the lower attraction- Panel retainer to the cabinet.
- Remove the attraction glass. 4, Remove the lower retainer. Pole Position
Remove the two wood screws that secure the tube and speaker board to the cabinet. Slide this board out of the cabinet. After making necessary repairs or replacements, make sure that the tube and speaker board is pushed all the way back on the tube and speaker panel when you reinstall the board.
Replacing the Fluorescent Tube:
- Check that the green ground wire is securely attached to the large metal bracket and the ballast transformer on the wood panel. If the tube is not grounded, it may not start.
- Remove the cardboard locking tab at each end of the tube (see Figure 3-12). Slightly rotate the tube up or down and carefuliy remove it from the tube holder.
- Replace it with a new tube. Do not snap in the tube vigorously— you may break it, causing an implosion! Replace the locking tabs.
Replacing the Upper Speaker:
- Disconnect the two plug-in connectors on the speaker.
- Remove the screws that attach the speaker to the board (see Figure 3-12). Replace with a new speaker and reinstall the tube and speaker board.
Replacing the Lower Speaker: From the back of the game, unlock and open the rear access panel. Refer to upper speaker removal procedure in Figure 3-12).
037410-01 (Attraction glass) 039418-01 (Attraction glass/ graphics) 003053-01 (Retainer)
039144-01 148001-013 (Speaker grille) d (Speaker)
Figure 3-11 Fluorescent Tube and Speaker Board Removal Upright Cabinet
3-22
Pole Position Maintenance, Repair, and Parts
448001.013 70-304 99-11006 (Speaker) (Tube) (Tab)
} a
179035001 | (Tube holder) — | 4037457-01 ‘ 178015-112 ® area v (Harness)
142028-001 (Transtormer) 142028-002 (Transformer)
(Starter) 99-11009 037469-01 (Socket) (Bracket)
Figure 3-12 Fluorescent Tube and Speaker Board Assembly U.S-Built Upright Cabinet A039415-01 B lreland-Built Cabinet A039415-02 B Parts List
Part No, Description For U.S:Built Upright Cabinet 142028-001 60 Hz, 118 V, Ballast Transformer (used on A038504-01 assembly) 037410-01 Attraction Glass 039485-03 Attraction Glass Film (not shown) For Ireland-Built Upright Cabinet 142028-002 60 Hz, 118 V, Ballast Transformer (used on A038504-01 assembly) 039418-01 Attraction Glass with Graphics For U.S; and Ireland-Built Upright Cabinet A037540-01 Ground Wire with Ring Lug AQ37457-01 Tube and Speaker Harness Assembly 70-304 18-Inch, 15 W, Cool White Fluorescent Tube 78-6900402 Vinyl Foarn Single-Coated Adhesive Tape, %4-Inch Wide x ¥%-Inch Thick 79-561816P Spring-Connector Wire Nut for 16- to 18-Gauge Wires 99-11003 Fluorescent Tube Starter 99-11006 Fluorescent Tube Locking Tab (tab consists of two pieces) 99-11009 Starter Socket 037469-01 Steel Tube Bracket 003053-01 Upper and Lower Attraction Glass Retainer 039144-01 Speaker Grille 148001-013 6x 9-Inch Oval, 4-Ohm, 6-Ounce, Shielded High-Fidelity Speaker 476015-112 #10 x %-Inch Pan Head Machine Screw 178035-001 2-Pin Fluorescent Tube Holder 179125-001 Grounding Clip {not shown) *146001-001 6x 9Inch Oval, 4-Ohm, 6-Ounce, High-Fidelity Speaker—mounied to the cabinet near the coin door, behind speaker grille part no. 039144-01
3-23
Maintenance, Repair, and Parts
Sit-Down Cabinet
Replacing the Front Speakers:
- For the right speaker, unlock and open the rear access panel (see Figure 3-13). For the left speaker, open the control panel (see Figure 3-3). Unplug the two plug-in connectors. Remove the two screws that secure the speaker to the wood speaker panel. gn Replacing the Seat-Panel Speakers:
4.
5. Pole Position
Py Remove the six wood screws that secure the seatback panel to the cabinet (see Figure 3-13). Lean the seat-back panel forward. Disconnect the two plug-in connectors on each speaker. Remove the seat-back panel from the player area of the cabinet. Remove the four screws that secure each speaker to the seat-back panel. Reassemble in reverse order.
Figure 3-13 Sit-Down Cabinet Speaker Removal
3-24
Pole Position
D. Video Display
Removing the Video Display From the Upright Cabinet: 1. From the back of the cabinet, unlock and open the tear access panel. Unplug the connectors from the display, and disconnect the ground wire (see Figure 3-14), Remove the retainer that holds the display shield in Place. Lift the display shield up and out of the cabinet. Carefully remove the cardboard display bezel. Remove the hardware that secures the display to the cabinet. Carefully pull the video display out through the front of the cabinet, with your hands on the top and bottom of the display bracket. Place the display in a protected location. After servicing the display, reinstall it in the reverse order.
Nut/Washer
039417-01 039407-01
(Shield) (Bezel)
78-6900402 (Tape) \ A200001-01 (Atari display) Maintenance, Repair, and Parts
DAG Spring Connector
Focus Connector
CRT Neck
201018-01 (Bracket)
Figure 3-14A Video Display—Atari CRT Neck PCB
3-25
Maintenance, Repair, and Parts Pole Position
Figure 3-14A Video Display—Atari Parts List
Part No. Description
A200001-01 19-Inch Atari Color Raster-Scan Display Acceptable substitute is part no. 92-049—19-inch Electrohome Display 039371-01 Retainer (not shown) 039407-01 Display Bezel 039417-01 Display Shield 201018-01 Mounting Bracket 78-6300402 Vinyl Foam Single-Coated Adhesive Tape, ¥%-Inch Wide x %-Inch Thick
Removing the Video Display From the Sit-Down Cabinet:
1. From the back of the cabinet, unlock and open the rear access panel. Unplug the 6-pin connector from the video chassis, the 2-pin 110-VAC connector, and disconnect the ground wire (see Figure 3-14). Remove the four sets of hardware that secure the video display to the wood display shelf. Open the control panel (see Figure 3-3).
3-26 Move to the player area of the cabinet. Grasp the bottom edge of the video display shield and slide the shield out and down. Make sure the foam tape on the bottom of the shield is in good condition. Remove any staples that may secure the bezel to the cabinet. Then, carefully grasp the bottom edge of the cardboard bezel and remove it from the cabinet. Pull the display out through the front of the cabinet. Place the display in a protected location. After servicing the display, reinstall in reverse order.
Pole Position
039371-01 (Retainer) Maintenance, Repair, and Parts
03914801 HD (Shield) 039149-01 fH 039417-01 (Bezeh (Srield) 039407-01 | (Bezel) | 92.049 (Electrohome display) &
78-6900402 (Shel) / (Tape) 03912302 2] S 78-6900804 (Shin (Tape) as)
Figure 3-14B Video Display—Electrohome Parts List
Part No. Description For Upright Cabinet 039363-02 Display Shelf 039371-01 Retainer 039407-01 Display Bezel 03941701 Dispiay Shield 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, %-Inch Wide x %Inch Thick For Sit-Down Cabinet 039123-02 Display Shelf 03914801 Display Shield 039149-01 Display Bezel 78-6900804 Vinyl Foam Single-Coated Adhesive Tape, 2-Inch Wide x Inch Thick For Upright and Sit-Down Cabinets 92-049 19-Inch Electrohome Color Raster-Scan Display A/ternate display is part no. 139003-1004—19-Inch Matsushita Color Raster-Scan Display
3-27
Maintenance, Repair, and Parts Pole Position
sts The utility panel is located inside the upper coin door. E. Utility Panel This panel includes the volume control(s), self-test switch, auxiliary coin switch, and the coin counter(s) (see Figure 3-15). The auxiliary coin switch is used to credit the game without tripping the coin counter. Before removing or repairing the utility panel, turn the game off. N OTE
Only Ireland-Built cabinets have two coin counters. If using both coin counters, the pad at 10D (pins 11 and 12) on the CPU PCB must be split. Players may receive an electrical shock if the utility panel is not properly grounded! After servicing any parts on the panel, make sure that the ground wire is firmly attached to the utility panel.
A039254-01 03945701 (Dual component (Utility panel— harness) US.-Built Upright only) A038004-01 039295-01 BAP (Utility panel (Utility panel) “5 harness) A002465-01 2 (Coin counter) ~ = 179125-001 A . 1039248-01 178070-001 (Grounding clip) (Vol. control harness) (Vol. control knob)
(Vol. control)
176018-002 (Screw)
SELF-TEST SWITCH (63-001)
75-9910W0 (Auxiliary (Stamped nut) coin switch) SWITCH NOT USED
Figure 3-15 Utility Panel Assembly A039391-xx G
3-28
Pole Position Maintenance, Repair, and Parts
Utility Panel Assembly Parts List
Part No. Description For U.S.-Built Upright Cabinet 039457-01 Utility Panel (for 2 volume controls) For lreland-Built Upright Cabinet 039295-01 Utility Panel (for 4 volume controls) For U.S.- and Ireland-Built Upright Cabinet A039254-01 Dual Component Harness Assembly For U.S.- and Ireland-Built Sit-Down Cabinet A038004-01 Utility Panel Harness Assembly A039248-01 Volume Control Harness Assembly 039295-01 Utility Panel (for 4 volume controls) For U.S.- and Ireland-Built Upright and Sit-Down Cabinets A002465-01 6 V Coin Counter 19-9032 50 , 12.5 W Volume Control 62-041 SPST Momentary-Contact Pushbutton Auxiliary Coin Switch with Black Cap 69-001 DPDT Self-Test Switch 72-HA4608S #6-32 x Ve-Inch Thread-Forming Screw 75-9910W0 #156-32 Stamped Nut 176018-002 #6-32 x Ye-Inch Cross-Recessed Pan-Head Screw 178070-001 Volume Control Knob 179125-001 Grounding Clip
3-29
Maintenance, Repair, and Parts Pole Position
FE Coin Doors
170000-001 (Lamp)
179047-001 (Lamp 99-15023 (Base Plate)
99-15056 (Screw for Bezel) 99-15026 (Coin Inlet)
99-15025 (Coin Inlet)
99-15054 (Pivot for Lever)
99-15055 (Retaining Screw)
99-15028 N
75-9145 ‘(Coin Return Box) (Hex Nut) (HExNuD 6 056 (Lock Wash.)
99-15056 ~*~ ew for Bezel) CA 99-15075 (Sw. Adjuster)
99-15029 (Bracket) -<— 99-15060 (Sw. Cover)
99-15042 (Switch)
T21414S (Screw)
Figure 3-16 Vertically Mounted Coin Door 171034-xxx
3-30
Pole Position Maintenance, Repair, and Parts
99-15038 (A037542-01 (Bezel for Button) (Harness—not shown)
99-15073 |. 99-15001 thru 99-15011 (Upper we (Return Button)
99-15063 (Screw)
. "9915039 dock ney ) Se ‘ 4 (Bezel for Cover) ‘ 199-15036, (Cover)
038091-01 (Coin Box) 99-15066 (Screw)
99-15074 (Lower Door)
(Doors and Frame) 99-15072 (Door Frame)
171034-001 — U.S. 25¢/25¢ Coin Door 171034-006 — U.K. 20 P/50 P Coin Door 171034011 — German 1 M/5 M Coin Door 171034-003 — Canadian 25¢/25¢ Coin Door 171034-009 — German 2 M1 M Coin Door 171034015 — French 2 F/1 F Coin Door 171034-005 — U.K. 19 P/50 P Coin Door 171034-010 — German 2 M/5 M Coin Door
Figure 3-16 Vertically Mounted Coin Door, continued 171034-xxx
3-31
Maintenance, Repair, and Parts Pole Position
Vertically Mounted Coin Door Parts List
Part No. Description A037542-01 Harness Assembly 7214148 #4-40 x ‘-Inch Cross-Recessed Pan-Head Steel Machine Screw 75-056 #6 Internal-Tooth Zinc-Plated Steel Lock Washer 75-9148 #4-40 Steel Machine Hex Nut 75-3414S, #4-40 x %-Inch 82° Cross-Recessed Flat-Head Steel Machine Screw 99-15001 Coin Return Button with U.S. 25¢ Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate 99-15003 Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20¢ Price Plate 99-15011 Coin Return Button with Italian 100 Lire Price Plate 99-15023 Base Plate 99-5025 Left Half of Coin Inlet 99-15026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box 99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15036 Metal Coin Return Cover 99-15038 Bezel for Coin Return Button 99-15039 Metal Bezel for Coin Return Cover 99-15040 Coin Return Lever 99-15042 Coin Switch for U.S, 25¢ 99-5052 Spring for Coin Return Button 99-15054 Pivot for Coin Return Lever 99-15055 Retaining Screw 99-15056 #4-40 x %-Inch Cross-Recessed Pan-Head Steel Machine Screw 99-15060 Switch Cover 99-15063 Screw for Hinge 99-15066 Screw for Clamp 99-15067 Lock Assembly 99-15070 Doors and Frame 99-15071 Clamp for Frame 99-15072 Door Frame 99-15073 Upper Door 99-15074 Lower Door 99-15075 Switch Adjuster 038091-01 Coin Box {Not included in assembly) Acceptable substitute is part number A037491-01 170000-001 6.3 V Miniature Wedge-Base Incandescent Lamp 171006-035 Metal Coin Mechanism 179047-001 Lamp Base
3-32
Pole Position Maintenance, Repair, and Parts
99-10140 171006-035 (Panel assy.) (Coin mechanism)
75-9488 a (Locknut) “7 I 99-10116 DW TREA SS (Lever)
99-10152 (Right coin inlet)
99-10096 (Fastener) 75-9448 (Hex nut)
99-10151 (Left coin inlet)
99-10080 (lamp ~~ BS 70-11-47 (Lamp)
/ (Bar retainer) 72-9406S (Screw) S ° 99-10147 (Harness)
B 99-1014 a * (Bracket assy.) «
99-10153 99-10042 thru 99-10045, (Coin switch assy.)
99-10150 ~—— (Switch cover)
99-10075 thru 99-1078 (Switch wire) 99-1008 (Retainer) 7514128 (Screw)
Figure 3-17 American-Made Coin Door 171027-001 A
3-33
Pole Position
ge ro S ~ 2 Bs 52 $ > 28 #2 q3 8 ga =8 8 S83 ss se Be 2 yo Zc 8 2: ge eo oe EP es $5 Bs
5 8 8 a
A a foo a
99-10148 (Lock)
Figure 3-17 American-Made Coin Door, continued 171027-001 A Maintenance, Repalr, and Parts
(Coin door) ——> 4 o
@ ze OS
3-34
Pale Position Maintenance, Repair, and Parts
American-Made Coin Door Parts List Assemblies and components in the following parts list are shown in Figure 3-17.
Part No. Description A039576-01 Coin Option Interconnect Assembly (not shown) 171006-035 Metal Coin Mechanism for U.S. $.25 65-441C Coin Switch 70-11-47 Miniature Bayonet Lamp 72-9406S #4-40 x %-Inch Truss-Head Screw 72-HA1404C, #4-40 x %4-Inch Pan-Head Screw 72-JA1405B #4-40 x 31-Inch Pan-Head Screw 75-14128 #4-40 x %-Inch Pan-Head Screw 75-994S, #4-40 Lock Nut 99-10008 Retainer 99-10042 Coin Switch Assembly for Belgium 5 Fr and US. $.25 99-10043 Coin Switch Assembly for German 1 DM, Japanese 100 Yen, Swiss 1 Fr 99-10044 Coin Switch Assembly for German 2 DM, Italian 100 L, U.S. $1.00 99-10045 Coin Switch Assembly for Australian $.20, German 5 DM, British 10 P 99-10068 Coin Return Chute 99-10075 Switch wire (incfuded in coin switch assembly) 99-10076 Switch wire (included in coin switch assembly) 99-10077 Switch wire (included in coin switch assembly) 99-10078 Switch wire (included in coin switch assembly) 99-10080 Lamp socket 99-10081 Key holder 99-10096 Fastener 99-10104 Bar retainer 99-10105 Bar 99-10115 Spring 99-10116 Plastic Coin Return Lever 99-10117 Steel Coin Return Door 99-10118 Amber Coin Return Button 99-10119 Amber Coin Button for U.S. $.25 99-10134 Coin Button Cover 99-10139 Coin Door 99-10140 Coin Door Inner-Panel Assembly 99-10141 Diecast Coin Return Cover 99-10142 Diecast Button Housing 99-10143 Coin Door Frame 99-10144 Coin Door Channel Clip 99-10145 Offset Cam (includes 99-10148—Lock) 99-10146. Coin Inlet Chute Assembly 99-10147 American-Made Coin Door Harness 99-10149 Service Door 99-10150 Switch Cover 99-10151 Left Coin Inlet 99-10152 Right Coin Inlet 99-10153 Coin Return Box 99-10154 Bracket Assembly
3-35
Maintenance, Repair, and Parts Pole Position
G. Printed-Circuit Boards
039378-03 (Retainer) A037767-01 (EMI Shield PCB)
176015-110 Shield PCB 037873-01 (Screw) (Spacer)
A039431-01 (End PCB)
<j \e / : : 72-1404F 034536-03 A (Screw) (Foam pad) i @ A037701-01 72.1604F (EMI cage) (Screw)
A039187-21 178044-242 A039185-21 (Pole Position Video PCB) (Grommet) (Pole Position CPU PCB) 175009-221 Note sher (Washer) 178045-442 ‘The FCC requires that the game (Fastener) PCB be housed in the EMI cage with the Shield PCB attached.
03543501 176015-110 A038435-05 (Screw) (Regulator! —“ 175004-708 Audio |! PCB) (Washer)
“Steps 1, 10, and 11 are not illustrated.
Figure 3-18 Removing the Printed-Circuit Boards
3-36
Pole Position
Before you remove or repair any printed-circuit board, turn the game off.
Removing the Printed-Circuit Boards: Removing the Game PCBs from the EMI Cage
- Open the rear access panel.
- The game printed-circuit boards (PCBs) are located inside the electromagnetic interference (EMI) cage (see Figure 3-18). The EMI cage is located on the cabinet wail of the Upright game and on the inside of the rear access panel of the Sit-Down game. Unplug the two harness edge-connectors from the EMI Shield PCB.
- To remove the game PCBs, pull the eight nylon snap-in fasteners on the EMI Shield PCB to the unlocked position. Carefully slide the Shield PCB and attached PCBs straight out of their guides. Be careful not to twist the boards, as this may loosen connections or components. Removing the EMI Shield PCB from the Game PCBs
- Remove the two pan-head screws that connect the EMI Shield PCB to the spacers.
- Push the EMI Shield PCB off the game PCBs by applying pressure with your thumbs to the edge connec- Maintenance, Repair, and Parts
Unplug the End PCB that connects the two game PCBs. Determine which PCB you need to repair or replace, and remove the two pan-head screws that connect that PCB to the spacers. Replace or repair as required, and reinstall the PCBs. (Make sure the foam vibration damper is placed between the game PCBs.) Removing a Regulator/Audio Il PCB: 8.
9. To rernove a Regulator/Audio || PCB, disconnect the small harness connectors on ihe board. Remove the hardware that secures the Regulator/Audio I! PCB to the cabinet, and carefully lift the board from the retainer. Do not twist the board, as this may loosen connections or components. Replace or repair as required and reinstall the PCB.
Make sure that the connectors on each PCB are properly plugged in. Note that they are keyed to fit only one way. If they do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty.
- Close and lock the rear access panel. tors. 11, Important: Perform the self-test.
Printed-Circuit Board Mounting Hardware Parts List Assemblies and components in the following parts list are shown in Figure 3-18.
Part No. Description
U.S-Built Upright and Sit-Down Cabinets A037701-01 Electromagnetic Interference (EMI) Cage (includes guides) 72-1404F #4-40 x Ys-Inch Cross-Recessed Steel Screw 721604F #6-32 x V4-Inch Cross-Recessed Steel Screw 034536-03 Foam Pad 037873-01 Spacer 039378-03 Dual-Slotted Retainer 175004-708 #8 Fiber Washer 175009-221 Plastic Spacer (for EMI shield PCB) 72-6812S #8 x ¥%-Incn Steel Machine Screw 178044-242 Grommet 178045-442 Snap-In Fastener
Jreland-Built Upright and Sit-Down Cabinets” 726624S #6 x 1 ¥2-Inch Cross-Recessed Pan-Head Tapping Screw 74-5608NN #6-32 x Y2-Inch Spacer 75-99516 #6-32 Nut/Washer Assembly 034536-02 Foam Pad 039157-02 Dual-Slotted PCB Retainer 175004-706 #6 Fiber Washer 175004-708 #8 Fiber Washer 72-6812S #8 x %-Inch Steel Machine Screw 178020-750 Nylon Spacer
*Not shown in illustration
Maintenance, Repair, and Parts
@ 8 am "Teal @
i e = CH ne! bale A ie ini i rat
| hag | | ie | Hy | al | ae | i i |
| Saat | Ld | : | ji | i Rt | li) | a |
jad 2)
| fo | Soo | et | B | ||
| o | 1 | E 1 | x a | L_| |
| a | ‘| | a) | ad Re | Ye |
| 7 | ORAL BE eae | “is | HE | |
| oS) | GE | hes | r | - 8 |
an Bs
| z | = | rr Re | xo 7m Mm 90 8 > |
Figure 3-19 Central Processing Unit (CPU) Printed-Circuit Board Assembly A039185-21 E
3-38 Pole Position
Pole Position Maintenance, Repair, and Parts
Central Processing Unit Printed-Circuit Board Assembly Parts List
Assemblies and components in the following parts list are shown in Figure 3-19.
| Designator | Description | Part No. |
Capacitors
| C2-C5 | 0.01 uF, 100 V Radial-Lead Mylar Capacitor | 21-101103 |
| Ccé | 33 pF, 100 V Radial-Lead Epoxy-Dipped Mica Capacitor | 128002-330 |
| C7 | 0.1 uF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122002-104 |
| ca | 10 pF, 25 V Aluminum Electrolytic Fixed Axial-Lead Capacitor Acceptable | 24-250106 |
substitute is part no. 24-35016
| C10 | 0.1 pF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122002-104 |
| ci | 47 »F, 10 V Aluminum Electrolytic Fixed Axial-Lead Capacitor Acceptabie | 24-100476 |
substitute is part no. 24-250476 or 24-160476
| C12 | 0.1 pF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122002-104 |
| C13 | 0.01 uF, +80%, -20%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-103 |
| C14, C15 | 0.1 pF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122002-104 |
| C16-C23 | 001 uF, +80%, -20%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-103 |
| C24, C25 | 0.1 xF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122002-104 |
| C26 | 47 uF, 10 V Aluminum Electrolytic Fixed Axial-Lead Capacitor Acceptable | 24-100476 |
substitute is part no. 24-250476 or 24-160476
| C27, C28 | 0.0022 pF, +10%, 100 V Radial-Lead Plastic Film Capacitor | 121022-222 |
| C29, C30 | 0.022 uF, 100 V Radial-Lead Mylar Capacitor | 21-101223 |
| C31,C32 | 0.01 pF, +80%, -20%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-103 |
| C33, C34 | 0.047 pF, 100 V Radial-Lead Mylar Capacitor | 21101473 |
| C35 | 0.022 uF, 100 V Radial-Lead Mylar Capacitor | 21101223 |
| C36 | 0.0047 pF, 100 V Radial-Lead Mylar Capacitor | 21-101472 |
| C37 | 0.001 pF, 100 V Radial-Lead Mylar Capacitor | 21-101102 |
| C38 | 0.0047 uF, 100 V Radial-Lead Mylar Capacitor | 21-101472 |
| C39, C40 | 0.01 nF, 100 V Radial-Lead Mylar Capacitor | 21-101103 |
| C41 | 47 uF, 10 V Aluminum Electrolytic Fixed Axial-Lead Capacitor Acceptable | 24100476 |
substitute is part no, 24-250476 or 24-160476
| C42, C43 | 0.0047 uF, 100 V Radial-Lead Mylar Capacitor | 21-101472 |
| C44,C45 | 0.001 nF, 100 V Radial-Lead Mylar Capacitor | 21-101102 |
| C46. | 470 yF, 16 V Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-250477 |
| C47-C56 | 22 uF, 16 V Aluminum Electrolytic Fixed Axial-Lead Capacitor Acceptable | 24-160226 |
substitute is part no. 24-100477 or 24-350266
| C57-C84 | 0.1 pF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122002-104 |
| C82 | 0.001 pF, 100 V Radial-Lead Mylar Capacitor | 21-101102 |
| cag | 100 pF, 100 V Mica Capacitor | 128002-101 |
Diodes
| CRi | Type-MV5053 Light-Emitting Diode | 38-MV5053 |
| CR2 | 6.2 V, +5%, 1 W Type-1N4735A Zener Diode | 131009-001 |
| CR3, CR4 | 100 V, Type-1N914 Switching Diode | 31-1N914 |
| CR5 | Type-1N4001, 50 V Rectifier Diode | 31-1N4001 |
| CR6 | 39 V +5%, Type-1N748A Zener Diode | 131000-002 |
| CR7-CR12 | 100 V, Type-1N914 Switching Diode | 31-1N914, |
| 3A | Type-Z8002 16-Bit Microprocessor | 137275-001 |
| 3c | Type-74LS373 Integrated Circuit | 37-74LS373 |
| 3F, 3H | Custom Integrated Circuit 10 | 137281-001 |
(Continued on next page)
3-39
Maintenance, Repair, and Parts Pole Position
Central Processing Unit Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. |
| 3M/N | Type-74S32 Integrated Circuit | 97-74832 |
| 3M, 4C | Type-74LS373 Integrated Circuit | 37-74LS373 |
| 4F, 4H | Custom Integrated Circuit 10 | 137281-001 |
| 4M | Type-74LS373 Integrated Circuit | 37-74LS373 |
| 4N | Type-Z8002 16-Bit Microprocessor | 137275-001 |
| 5A | Type-74LS74 Integrated Circuit | 37-7ALS74 |
| 5c | Type-12L6 Programmable-Array Logic 1 | 137280-001 |
| SD | Type-74LS367 Integrated Circuit | S7-TALS367 |
| 5E | Type-74LS244 Integrated Circuit | S7-74LS244 |
| 5J | Type-74LS367 Integrated Circuit | 37-7T4LS367 |
| 5K | Type-74LS244 integrated Circuit | 37-74LS244 |
| 5L | Type-74LS368 Integrated Circuit | 137168-001 |
| 5M | Type-74LS158 Integrated Circuit | 137203-001 |
| 5N | Type-74LS74 integrated Circuit | 37-74LS74. |
| 6A | Type-74LS161 Integrated Circuit | 37-74LS161 |
| 6C | Type-74LS74 Integrated Circuit | 37-74LS74 |
| 60-6F | Type-74LS367 Integrated Circuit | 37-74LS367 |
| 8H | Custom Integrated Circuit 08 | 137186-001 |
| 6J, 6K | Type-74LS157 integrated Circuit | 37-74LS157 |
| 6L | Type-74LS109 Integrated Circuit | 37-74LS109 |
| 6M | Type-74LS00 integrated Circuit | 37-74LS00 |
| 6N | Type-74S163 Integrated Circuit | 137274-001 |
| 7C | Type-10L8 Programmable-Array Logic 3 | 137279-001 |
| 7D | Type-Z80A 8-Bit Microprocessor | 137194-001 |
| 7K/IL | Type-74LS138 Integrated Circuit | 137177-001 |
| 7™ | Custom Integrated Circuit 07 | 137193-001 |
| 7N | Type-74504 Integrated Circuit | 37-74804 |
| 8D | Type-74LS138 Integrated Circuit | 137177-001 |
| 8E | Type-74LS259 Integrated Circuit | 37-74LS259 |
| 8F | Type-74L$367 Integrated Circuit | 37-74LS367 |
| 8H | Custom Integrated Circuit 08 | 137186-001 |
| Bd | Type-ADC0804 Integrated Circuit | 137273-001 |
| 8K | Type-4066 Integrated Circuit | 37-4066 |
| 8L | Type-4584B Integrated Circuit | 37-4584B |
| 8M | Type-74S04 Integrated Circuit | 37-74804 |
| 9E | Custom integrated Circuit 52 | 137284-001 |
| OFA | Custom Integrated Circuit 54 | 137285-001 |
| 9FB | Type-LM324 Integrated Circuit | 37-LM324 |
| 9H | Custom Integrated Circuit 06 | 137192-001 |
| OK | Custom integrated Circuit 53 | 137188-001 |
| 9M | Custom Integrated Circuit 51 | 137187-001 |
| 10A | Type-74LS138 Integrated Circuit | 137177-001 |
| 10C | Type-74LS374 Integrated Circuit | 37-74LS374 |
| 40D | Type-74LS174 Integrated Circuit | S7-7ALS174 |
| 10E, 10F | Type-74LS283 integrated Circuit | 137204-001 |
| 10H, 10J | Type-74LS273 Integrated Circuit | 37-74LS273 |
| 10K, 10L | Type-4066 Integrated Circuit | 37-4066 |
| +A | Type-74LS174 Integrated Circuit | S7-74LS174 |
| uC | ‘ype-7497 Integrated Circuit | 37-7497 |
| NE | Type-74LS273 Integrated Circuit | 37-74LS273 |
(Continued on next page)
3-40
Pole Position Maintenance, Repair, and Parts
Central Processing Unit Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. |
| 11F | Type-4051 Integrated Circuit | 137277-001 |
| 41H | Type-74LS174 Integrated Circuit | 37-7ALS174, |
| 1d | Type-74LS273 Integrated Circuit | 37-74LS273 |
| 11K-11M | Type-4086 Integrated Circuit | 37-4066 |
| 124 | Type-74LS174 Integrated Circuit | 37-74LS174 |
| 12B | Type-7497 Integrated Circuit | 37-7497 |
| 12C | Type-74LS161 Integrated Circuit | 37-74LS161 |
| 12D | Type-74LS393 Integrated Circuit | 37-74LS393 |
| 12H, 12J, 12M | Type-LM324 Integrated Circuit | S7-LM324 |
Random-Access Memories
| 7E | CMOS Random-Access Memory | 137278-001 |
| 7, 7K | Random-Access Memory | 137199-001 |
Read-Only Memories
| cg | Electrically Programmable Read-Only Memory | Acceptable | 136014-106 |
substitute is part no, 136014-147
| 3E | Electrically Programmable Read-Only Memory | 136014-203 | |
| 3L | Electrically Programmable Read-Only Memory | 136014-101 | |
| 4 | Electrically Programmable Read-Only Memory | 136014-204 | |
| 4u | Electrically Programmable Read-Only Memory | 136014-102 | |
| 7F | Electrically Programmable Read-Only Memory | 136014-116 | |
| 7H | Electrically Programmable Read-Only Memory | 136014-105, | |
| 7L | Programmable Read-Only Memory | Acceptable substitute is part | 136014-117 |
no. 136014-160 for lreland-Built cabinets
| 11D | Programmable Read-Only Memory | 136014-118 | |
| 42E | Electrically Programmable Read-Only Memory | Acceptable | 136014-114 |
substitute is part no. 136014-149
| 12F | Electrically Programmable Read-Only Memory | Acceptable | 136014-110 |
substitute is part no. 136014-148
Resistors
| R1 | 2200, +5%, V4 W Resistor | 110000-221 |
| R2-R8 | 2.2 k2, +5%, Ya W Resistor | 410000-222 |
| RQ | 1kQ, +5%, Ys W Resistor | 110000-102 |
| R10-R16 | 2.2 k2, +5%, v4 W Resistor | 110000-222 |
| R17-R20 | 1kQ, +5%, %4 W Resistor | 110000-102 |
| R21-R26 | 1kQ, +5%, Ys W Resistor | 110000-102 |
| R27-R34 | 2.2 kQ, +5%, v4 W Resistor | 110000-222 |
| R35 | 1kQ, +5%, Va W Resistor | 110000-102 |
| R36-R38 | 2.2 kQ, +5%, Ya W Resistor | 110000-222 |
| R39-R43 | 1kQ, 45%, 1% W Resistor | 110000-102 |
| R45 | 47, +5%, v4 W Resistor | 110000-470 |
| R46, R47 | 1k@, +5%, Va W Resistor | 110000-102 |
| R52 | 470.9, 45%, Ys W Resistor | 410000-471 |
| R53 | 1kQ, +5%, V4 W Resistor | 110000-102, |
| R54 | 470 2, +5%, % W Resistor | 110000-471 |
| R55, R56 | 1kQ, +5%, Ys W Resistor | 110000-192 |
| R57-R60 | 4700, +5%, v4 W Resistor | 110000-471 |
(Continued on next page)
3-41
Maintenance, Repair, and Parts Pole Position
Central Processing Unit Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. |
| Ret | 4.7kO, +5%, Ye W Resistor | 110000-472 |
| R62 | 10 k2, +5%, % W Resistor | 110000-103 |
| R63 | 22 kQ, +5%, V4 W Resistor | 110000-223 |
| R64 | 47k2, +5%, Ya W Resistor | 110000-473 |
| R65 | 4.7kQ. +5%, V4 W Resistor | 110000-472 |
| R66 | 10 kQ, +5%, ¥4 W Resistor | 110000-103 |
| R67 | 22k, +5%, 4 W Resistor | 110000-223 |
| R68 | 47 kQ, +5%, ¥ W Resistor | 110000-473 |
| R69 | 4.7kQ, +5%, vs W Resistor | 110000-472 |
| R70 | 10 kQ, +5%, % W Resistor | 410000-103 |
| R71 | 22 kQ, +5%, Ya W Resistor | 110000-223 |
| R72 | 47kQ, +5%, % W Resistor | 110000-473. |
| R73 | 4.7kQ, +5%, Ys W Resistor | 110000-472 |
| R74 | 10 kO, +5%, Ya W Resistor | 110000-103 |
| R75 | 22kQ, +5%, 4 W Resistor | 110000-472 |
| R76 | 47 kf, +5%, % W Resistor | 110000-473 |
| R77-R80 | 1kO, +5%, % W Resistor | 110000-102 |
| Ret | 2202, +5%, v4 W Resistor | 110000-221 |
| Re2 | 1kQ, +5%, % W Resistor | 110000-102 |
| R83 | 4702, +5%, Ya W Resistor | 110000-471 |
| R84 | 1kQ, +5%, Ys W Resistor | 110000-102 |
| Res | 2.2kQ, +5%, Ys W Resistor | 410000-222 |
| R86 | 3300, +5%, Y% W Resistor | 110000-331 |
| R87 | 1kQ, +5%, % W Resistor | 110000-102 |
| R88 | 22kQ, +5%, Ys W Resistor | 110000-223 |
| R89 | 1002, +5%, % W Resistor | 110000-101 |
| R90-R92 | 1kQ, +5%, Vs W Resistor | 110000-102 |
| R93, R94 | 3302, +5%, V4 W Resistor | 410000-331 |
| R95 | 1k, +5%, ¥4 W Resistor | 110000-102 |
| R96 | 4.7kQ, +5%, Ys W Resistor | 110000-472 |
| R97 | 2200, +5%, ¥ W Resistor | 110000-221 |
| ROB | 4.7 KO, +5%, Vs W Resistor | 110000-472 |
| R99 | 2200, +5%, %& W Resistor | 110000-221 |
| R101 | 2.2k0, +5%, Ys W Resistor | 110000-222 |
| R102, R104 | 1kQ, 5%, Y% W Resistor | 110000-102 |
| R103 | 4.7 kQ, +5%, Ys W Resistor | 110000-472 |
| R106 | 1k, +5%, % W Resistor | 110000-102 |
| R107 | 4.7 kQ, +5%, Ya W Resistor | 110000-472 |
| R108-115 | 1kQ, +5%, % W Resistor | 110000-102 |
| RIG | 15 kQ, +5%, Ys W Resistor | 110000-152 |
| RINT | 1kQ, +5%, % W Resistor | 110000-102 |
| R118 | 4.7k0, +5%, % W Resistor | 110000-472 |
| R119 | 10kQ, +5%, % W Resistor | 110000-103 |
| R120, R121 | 22kQ, +5%, % W Resistor | 410000-223 |
| R122 | 120 kQ, +5%, % W Resistor | 110000-124 |
| Ri23 | 4700, +5%, Vs W Resistor | 110000-471 |
| R124 | 47kQ, +5%, ve W Resistor | 110000-473 |
| R125 | 12k2, +5%, Ys W Resistor | 110000-123 |
(Continued on next page)
3-42
Pole Position Maintenance, Repair, and Parts
Central Processing Unit Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. |
| R126 | 4.7kQ, +5%, 4 W Resistor | 110000-472 |
| R127, R128 | 2.2 kQ, +5%, Y4 W Resistor | 110000-222 |
| R129, R130 | 3.3 kQ, +5%, Ya W Resistor | 110000-332 |
| R131 | 10 kO, +5%, Ys W Resistor | 110000-103 |
| R132 | 22 kQ, +5%, Va W Resistor | 110000-223 |
| R133 | 15kQ, +5%, % W Resistor | 110000-153 |
| R134 | 120 kQ, +5%, % W Resistor | 110000-124 |
| Ri35 | 4702, +5%, Ye W Resistor | 110000-471 |
| R136 | 47 kQ, +5%, Va W Resistor | 110000-473 |
| R137 | 15 k@, +5%, % W Resistor | 110000-153 |
| R138 | 10 KO, +5%, %4 W Resistor | 110000-103 |
| R139 | 22k, +5%, ¥4 W Resistor | 110000-223 |
| R140 | 180 kQ, +5%, Ye W Resistor | 110000-184 |
| R141 | 4702, +5%, Ys W Resistor | 110000-471 |
| R142, R143 | 22k0, +5%, %4 W Resistor | 110000-223 |
| R144-R151 | 1kQ, +5%, V4 W Resistor | 110000-102 |
| Ri52 | 47kQ, +5%, Ys W Resistor | 110000-473 |
| R153. | 4702, +5%, Ya W Resistor | 110000-471 |
| R154 | 10 kQ, +5%, Y W Resistor | 110000-103 |
| R155 | 82kQ, +5%, % W Resistor | 110000-823 |
| R156, R157 | 47 kQ, +5%, % W Resistor | 110000-473 |
| R158 | 22 kQ, +5%, V4 W Resistor | 110000-223 |
| R159 | 47k, +5%, V4 W Resistor | 110000-473 |
| R160 | 100 kQ, +5%, ¥% W Resistor | 110000-104 |
| R161-R165 | 2.2kQ, +5%, Va W Resistor | 110000-222 |
| R166 | 1kQ, +5%, % W Resistor | 110000-102 |
| R167 | 2.2 kQ, +5%, V4 W Resistor | 110000-222 |
| R168 | 4.7kQ, +5%, % W Resistor | 110000-472 |
| R169 | 220 kQ, +5%, Ys W Resistor | 110000-224 |
| R170 | 390k0, +5%, % W Resistor | 110000-394 |
| R171 | 4.7kQ, +5%, Ys W Resistor | 110000-472 |
| R172 | 15 kQ, +5%, ¥4 W Resistor | 110000-153 |
| R173 | 47kQ, +5%, Ya W Resistor | 110000-473 |
| R174 | 33k2, +5%, % W Resistor | 110000-333 |
| R175, | 10 kQ, +5%, Ys W Resistor | 110000-103 |
| R176 | 47 kQ, +5%, Ya W Resistor | 110000-473 |
| R177 | 1kQ, +5%, Y% W Resistor | 110000-102 |
| R178 | 75 kQ, +5%, V4 W Resistor | 110000-752 |
| R179 | 330 k0, +5%, Ya W Resistor | 410000-334 |
| R180, R181 | 47k, +5%, Ya W Resistor | 110000-473 |
| R182 | 1kQ, +5%, % W Resistor | 110000-102 |
| R183 | 22 kQ, +5%, V4 W Resistor | 110000-223 |
| R184 | 152, +5%, % W Resistor | 110000-153 |
| Rigs | 10 kQ, +5%, % W Resistor | 110000-103 |
| R186 | 1kQ, +5%, % W Resistor | 110000-102 |
| R187 | 330 kQ, +5%, % W Resistor | 110000-334 |
| R188 | 10 kQ, +5%, Y% W Resistor | 110000-103 |
| R189, R190 | 47 kQ, +5%, % W Resistor | 0000-473 |
(Continued on next page)
3-43
Maintenance, Repair, and Parts Pole Position
Central Processing Unit Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. |
| Rig | 1kQ, 45%, Y4 W Resistor | 110000-102 |
| R192 | 75 kQ, +5%, % W Resistor | 110000-753 |
| Ri93 | 15 kQ, +5%, % W Resistor | 110000-153 |
| R194 | 47k0, +5%, v4 W Resistor | 110000-473 |
| R195 | 10kQ, +5%, % W Resistor | 110000-103 |
| R196 | 1kQ, +5%, % W Resistor | 110000-102 |
| R197, R198 | 47 kQ, +5%, Ya W Resistor | 110000-473 |
| R199 | 1kQ, +5%, ¥4 W Resistor | 110000-102 |
| R200 | A7kQ, +5%, V4 W Resistor | 110000-473 |
| R201 | 15 kQ, +5%, Ya W Resistor | 110000-153 |
| R202 | 10 kQ, +5%, % W Resistor | 110000-103 |
| R203 | 1kQ, +5%, % W Resistor | 110000-102 |
| R204, R205 | 47 kQ, +5%, Ys W Resistor | 110000-473 |
| R206 | 1kQ, +5%, % W Resistor | 110000-102 |
| R207 | 20 k2, +5%, % W Resistor | 110000-203 |
| R208 | 10 kQ, +5%, % W Resistor | 110000-103 |
| R209 | 200, +5%, V4 W Resistor | 110000-203 |
| R210 | 10k, +5%, % W Resistor | 110000-103 |
| Renn | 20 kQ, +5%, %4 W Resistor | 110000-203 |
| R212 | 10 kQ, +5%, Ys W Resistor | 110000-103 |
| R213 | 20kQ, +5%, v4 W Resistor | 110000-203 |
| R214 | 10 kQ, +5%, Ya W Resistor | 110000-103 |
| R2is | 20kQ, +5%, %4 W Resistor | 110000-203 |
| R216 | 10 kQ, +5%, Vv W Resistor | 110000-103 |
| R217 | 20k, +5%, v4 W Resistor | 110000-203 |
| R218 | 10 kQ, +5%, V4 W Resistor | 110000-103 |
| R2t9 | 20kQ, +5%, % W Resistor | 110000-203 |
| R220 | 27 kQ, +5%, % W Resistor | 110000-273 |
| R223 | 1kQ, +5%, V4 W Resistor | 110000-102 |
| R225-R231 | 1kQ, +5%, v4 W Resistor | 110000-102 |
| R231-R238 | 2.2 k2, +5%, Ys W Resistor | 110000-222 |
| R239-R244 | 1kQ, +5%, % W Resistor | 110000-102 |
| R245 | 1000, +5%, Y% W Resistor | 110000-101 |
| R246 | 150 kQ, +5%, % W Resistor | 110000-154 |
| R249 | 1502, +5%, Ys W Resistor | 110000-151 |
| 1E | 2.2k, +2%, Dual-Inline-Package Resistor Network | 118003-222 |
| ON | 1kQ, +2%, Dual-inline-Package Resistor Network | 118003-102 |
Sockets
| 3A | 40-Contact Medium-Insertion-Force integrated Circuit Socket | 79-42C40 |
| 3E, 3F | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 3H | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 3L | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 4E, 4F | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 4H | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 4L | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 4N | 40-Contact Medium-insertion-Force Integrated Circuit Socket | 79-42C40 |
{Continued on next page)
3-44
Pole Position Maintenance, Repair, and Parts
Central Processing Unit Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. |
| 6H-9H | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 7D | 40-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C40 |
| 7E, 7F | 24-Contact Medium-insertion-Force Integrated Circuit Socket | 79-42C24 |
| 7H | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 7M | 28-Contact Medium-Iinsertion-Force Integrated Circuit Socket | 79-42C28 |
| BA | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 8C | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 9C | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 9E | 42-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C42 |
| OFA | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| OK | 42-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C42 |
| 9M | 42-Contact Medium-insertion-Force Integrated Circuit Socket | 79-42C42 |
| 12E, 12F | 28-Contact Medium-insertion-Force Integrated Circuit Socket | 79-42C28 |
Switches
| JA. | 8-Station, Single-Throw, Dual-Inline-Package Bit Switch | 66-118P IT |
| aL | 8-Station, Single-Throw, Dual-Iniine-Package Bit Switch | 66-118PIT |
Transistors
| Qi | Type-2N3906 40 V, 1 W, PNP Transistor | 33-2N3906 |
| Q2 | Type-2N3904 60 V, 350 mW, NPN Transisior | 34-2N3904 |
| Q3 | Type-MPS-A92 300 V, 500 mA, PNP Transistor | 33-MPSA92 |
| Q4 | Type-2N3904 60 V, 350 mW, NPN Transistor | 34-2N3904 |
| 5, Q6 | Type-2N6044 80 V, 8A, Darlington NPN Transistor | 34-2N6044 |
Miscellaneous
| B11 | 3.6 V, 100 mA Nickel-Cadmium Battery | 171028-001 |
| Wi | Lead-Spring Socket Terminal | 179131-001 |
Test Point Acceptable substitute is part no. 020670-07 179051-001 Jumper Staple 150009-001
| Q5, Q6 | Nylon Snap-in Fastener | 81-4302 |
3-45
Pole Position
aw & “ae + pcs | iz Beara.
Ses 125 (-'56)} tice Get sf tmel (—— 7) feos) fee] fans tas) fa] Sam) fae Sazg0
“ee : 4 [ eB Be. oe 3 ius — ao tesaas faa] a] ar) PEEP) Soa fs) see | [age] tel Bea zp) Sees) faa) ie Saat aS ayaa 4 ae ae ‘ ait Si eel fee | Sel Sl Se a) p= Es ions Ee ga an Sn 2 eral ieere | ews Foss] aoe Sinsv] Sipe - Re bined ge = = 2 = Bion Faz) $e] szes] fessor if ears fissce] fses Ca Sea] ra Ss) ate fee . fel la & ~
Sa 2657e Se Maintenance, Repair, and Parts
2 3 4 5 6 7 8 9 10 1" 12 13
Figure 3-20 Pole Position Video Printed-Circuit Board Assembly A039187-21 E
3-46
Pole Position Maintenance, Repair, and Parts
Pole Position Video Printed-Circuit Board Assembly Parts List
| Designator | Description | Part No. |
Capacitors
| C2 | 470 uF, 25 V Aluminum Electrolytic Axial-Lead Capacitor | 24-250477 |
| C3-C17 | 22 uF, 16 V Aluminum Electrolytic Axial-Lead Capacitor | 24-160226 |
| C18-C57 | 0.1 pF, +80%, -20%, 50 V Ceramic Disk Radial-Lead Capacitor | 122002-104 |
| C58 | 68 pF, 100 V, Mica Capacitor | 128002-680 |
| C59 | 22 pF, 100 V, Mica Capacitor | 128002-220 |
| C60 | 100 pF, 100 V, Mica Capacitor | 128002-101 |
| cR1 | Type-MV5053 Light-Emitting Diode | 38-MV5053 |
| CR2 | Type-1N4735A, 6.2 V, 1 W Zener Diode | 131009-001 |
Inductors
| LI-L3 | 1 uH, Y2 W Inductor | 141007-001 |
| L4 | 100 yH, + 10% Inductor | 141002-001 |
Integrated Circuits
| 2A | Type-74LS$138 Integrated Circuit | 137177-001 |
| 2E | Type-74LS74 integrated Circuit | 37-74LS74 |
| 2H | Type-74LS139 Integrated Circuit | 37-74.S139 |
| 2J | Type-74LS10 Integrated Circuit | 37-74LS10 |
| 2k | Type-74LS368 integrated Circuit | 137 168-001 |
| 3B | Type-74LS283 Integrated Circuit | 137204-001 |
| 3c | Type-74LS283 Integrated Circuit | 137204-001 |
| 3D | Type-74LS283 Integrated Circuit | 137204-001 |
| 3H | Type-74LS175 Integrated Circuit | 37-74LS175, |
| 30, 4 | Type-74LS174 Integrated Circuit | 37-74LS174 |
| 3K | Type-74LS283 Integrated Circuit | 137204-001 |
| st | Type-74LS283 Integrated Circuit | 137204-001 |
| 3M | Type-74LS02 Integrated Circuit | 37-74LS02 |
| 4B | Type-74LS367 Integrated Circuit | 37-74LS367 |
| 4c | Tpe-74LS367 Integrated Circuit | 37-74LS367 |
| 4H | Type-74LS157 Integrated Circuit | 37-74L8157 |
| 4k | Type-74LS174 Integrated Circuit | 37-74LS 174 |
| 4M, 5M | Type-74LS298 Integrated Circuit | 137201-001 |
| 4N, 5N | Type-74LS283 Integrated Circuit | 137204-001 |
| 5B | Type-74LS174 Integrated Circuit | 37-74LS174 |
| 5C | Type-74LS174 Integrated Circuit | 37-74LS174 |
| 5D | Type-74LS174 Integrated Circuit | 37-74LS174 |
| 5E | Type-74LS245 Integrated Circuit | 37-74LS245 |
| 5F, 6F | Type-74LS245 Integrated Circuit | 37-74LS245 |
| 5H | Type-74LS175 Integrated Circuit | 37-74LS175 |
| SJ | Type-74LS273 Integrated Circuit | 37-74LS273 |
| 6A | Type-74804 Integrated Circuit | 37-74S04 |
| 6B | Type-74LS368 Integrated Circuit | 137 168-001 |
| 6C. | Type-74L808 Integrated Circuit | 37-74LS08 |
| 6H | Type-74LS245 Integrated Circuit | 37-74LS245 |
| BJ | Type-74LS245 Integrated Circuit | 37-74LS245, |
| 6K | Type-74LS245 Integrated Circuit | 37-74LS245 |
| 6M, 7M | Type-74LS273 Integrated Circuit | 37-74LS273 |
| 7B | Type-74S163 Integrated Circuit Acceptable substitute is part no. | 137274-001 |
137287-001 or -002
| 7G | Type-74S04 Integrated Circuit | 37-74S04 |
| 7D | Type-74LS32 Integrated Circuit | 37-74LS32 |
(Continued on next page)
3-47
Maintenance, Repair, and Parts Pole Position
Pole Position Video Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. |
| 7L | Type-74LS273 Integrated Circuit | 37-74LS273 |
| 8B | Type-74S00 Integrated Circuit | 37-74S00 |
| 8c9C | Type-74LS157 Integrated Circuit | 37-74LS157 |
| 8D | Type-74LS158 Integrated Circuit | 137312-001 |
| 8E | Type-74LS158 Integrated Circuit | 137203-001 |
| 8L,9L. | Type-74LS174 Integrated Circuit | S7-TALS174 |
| 9B | Type-74LS20 Integrated Circuit | 37-74LS20 |
| 9D | Type-74LS298 Integrated Circuit | 137201-001 |
| 9E, 10E | Type-74LS257 Integrated Circuit | 37-7TALS257 |
| 9H | Type-74LS161 Integrated Circuit | 137287-001 |
| OJ | Type-74LS161 Integrated Circuit | 137287-001 |
| 9K | Type-7497 Integrated Circuit | 37-7497 |
| 9M, 10M | Type-74LS283 Integrated Circuit | 137204-001 |
| 9N | Type-74LS85 Integrated Circuit | 37-74LS85 |
| 10B | Type-74LS74 Integrated Circuit | 37-74LS74 |
| 10C | Type-74LS174 Integrated Circuit | 37-74LS174 |
| 10D | Type-74LS368 Integrated Circuit | 137168-001 |
| 10H | Type-74LS161 Integrated Circuit | 137287-001 |
| 10J | Type-74LS161 Integrated Circuit | 137287-001 |
| 10K | Type-74LS161 Integrated Circuit | 137287-001 |
| 10L | Type-74LS161 Integrated Circuit | 137287-001 |
| 40N | Type-74LS85 Integrated Circuit | 37-74LS85 |
| 1B | Type-74107 Integrated Circuit Acceptable substitute is part no. 137169-001 | 37-74107 |
| NE | Type-74LS174 Integrated Circuit | 37-74LS174 |
| 11H | Type-74LS174 Integrated Circuit | S7-7ALS174 |
| Md | Type-74LS273 Integrated Circuit | 37-74LS273 |
| 11K | Type-74LS139 Integrated Circuit | 37-74LS139 |
| iL | Type-74LS373 Integrated Circuit | 37-74LS373 |
| 11M | Type-74LS373 Integrated Circuit | 37-74LS373 |
| 12B | Type-74LS08 Integrated Circuit | 37-74LS08 |
| 12F | Type-74LS86 \ntegrated Circuit | 37-74LS86 |
| 13F | Type-74LS20 Integrated Circuit | 37-74LS20 |
For -21 version only
| 2F | ‘ype-07 Custom Integrated Circuit | 137193-001 |
| 3N | Type-02 Custom Integrated Circuit | 137190-001 |
| 4D | Type-09 Custom Integrated Circuit | 137282-001 |
| SL, 6L | Type-03 Custom Integrated Circuit | 137283-001 |
| 7E | Type-04 Custom Integrated Circuit | 137191-001 |
| 8N | Type-02 Custom Integrated Circuit | 137190-001 |
| 13H | Type-02 Custom Integrated Circuit | 137190-001 |
(Continued on next page)
3-48
Pole Position Maintenance, Repair, and Parts
Pole Position Video Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. |
Random-Access Memories 3E, 4E Random-Access Memory (200 ns) Acceptable substitute is part no. 137211-001 — 137198-001 (150 ns) SF, 4F Random-Access Memory (200 ns) Acceptable substitute is part no. 137211-001 — 137198-001 (150 ns)
| TF, 8F | Type-2114-2 (200 ns) Random-Access Memory | 90-7036 |
| 7H, 8H | Type-2114-2 (200 ns) Random-Access Memory | 90-7036 |
| 7d, 8J | Type-2114-2 (200 ns) Random-Access Memory | 90-7036 |
| 7K, 8K | Type-2114-2 (200 ns) Random-Access Memory | 90-7036 |
| QF, 10F | 55 ns Random-Access Memory | 137199-001 |
Programmable Read-Only Memories
| 2B | Type-82S129(17) Programmable Read-Only Memory | 136014-144 |
| 2c | Type-825129(16) Programmable Read-Only Memory | 136014-143 |
| 2D | ‘Type-82S129(15) Programmable Read-Only Memory | 136014-142 |
| 4L | Type-82S137(12) Programmable Read-Only Memory | 136014-145 |
| 5K | Type-82S129(11) Programmable Read-Only Memory | 136014-141 |
| 6D | Type-825123(14) Programmable Read-Only Memory | 136014-136 |
| 6E | Type-82S123(13) Programmable Read-Only Memory | 136014-135, |
| 8M | Type-82S129(10) Programmable Read-Only Memory | 136014-140 |
| 116 | Type-82S129(9) Programmable Read-Only Memory | 136014-139 |
| 1D | Type-82S129(8) Programmable Read-Only Memory | 136014-138 |
| WE | Type-82S129(7) Programmable Read-Only Memory | 136014-137 |
| 12H | Type-82S137(6) Programmable Read-Only Memory | 136014-146 |
For -21 version only
| aL | Electrically Programmable Read-Only Memory | 136014-127 |
| 2M | Electrically Programmable Read-Only Memory | 136014-128, |
| 2N | Electrically Programmable Read-Only Memory Acceptable substitute is | 136014-134 |
part no. 137205-001
| 6N | Electrically Programmable Read-Only Mernory Acceptable substitute is | 136014-133 |
part no. 137205-001
| 7N | Electrically Programmable Read-Only Memory Acceptable substitute is | 136014-132 |
part no. 137205-001
| 11N | Electrically Programmable Read-Only Memory Acceptab/e substitute is | 136014-231 |
part no. 136014-131
| 12d | Electrically Programmable Read-Only Memory | 136014120 |
| 12K | Electrically Programmable Read-Only Memory | 136014-122 |
| 12L | Electrically Programmable Read-Only Memory | 136014-124 |
| 12N | Electrically Programmable Read-Only Memory | 136014-126 |
| 130 | Electrically Programmable Read-Only Memory | 136014-119 |
| 13K | Electrically Programmable Read-Only Memory | 136014-121 |
| 13L | Electrically Programmable Read-Only Memory | 136014-123 |
| 13N | Electrically Programmable Read-Only Memory | 136014-125 |
(Continued on next page)
3-49
Maintenance, Repair, and Parts Pole Position
Pole Position Video Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. |
Resistors
| R1-R9 | 2.2 kQ, +5%, % W Resistor | 110000-222 |
| R10-R24 | 1kQ, +5%, Va W Resistor | 110000-102 |
| R25-R40 | 470 0, +5%, Vs W Resistor | 110000-471 |
| R41-R48 | 4.7kQ, +5%, % W Resistor | 110000-472 |
| R49-R52 | 1kQ, +5%, V4 W Resistor | 410000-102 |
| R55-R58 | 1kQ, +5%, Ys W Resistor | 110000-102 |
| R59 | 2200, +5%, vs W Resistor | 110000-221 |
| R60 | 470 2, +5%, % W Resistor | 110000-471 |
| R61 | 1kQ, +5%, % W Resistor | 110000-102 |
| R62 | 2.2kQ, +5%, Ya W Resistor | 110000-222 |
| R63 | 1kQ, +5%, % W Resistor | 110000-102 |
| R64, R65 | 822, +5%, V4 W Resistor | 110000-820 |
| R66 | 2200, +5%, % W Resistor | 110000-221 |
| R67 | 470 2, +5%, vs W Resistor | 110000-471 |
| R68 | 1kQ, +5%, V4 W Resistor | 110000-102 |
| R69 | 2.2kQ, +5%, % W Resistor | 110000-222 |
| R71, R72 | 820, +5%, V4 W Resistor | 110000-820 |
| R73 | 2200, +5%, Vs W Resistor | 110000-221 |
| R74 | 470 0, +5%, Ya W Resistor | 410000-471 |
| R75 | 1kQ, +5%, v4 W Resistor | 110000-102 |
| R76 | 2.2k0, +5%, ¥% W Resistor | 110000-222 |
| R77 | 1kQ, 45%, Ya W Resistor | 110000-102 |
| R78, R79 | 820, +5%, Vs W Resistor | 110000-820 |
| R80 | 1k@, +5%, % W Resistor | 110000-102 |
| R81 | 100 2, +5%, ¥ W Resistor | 110000-101 |
| R82-R85 | 1kQ, +5%, % W Resistor | 110000-102 |
| R86 | 2200, +5%, V4 W Resistor | 110000-221 |
| R87-R98 | 1kQ +5%, Ys W Resistor | 110000-102 |
| R99 | 10 kQ, +5%, % W Resistor | 110000-103 |
| R100 | 2200, +5%, Ys W Resistor | 110000-221 |
| R101 | 10kO, +5%, v4 W Resistor | 110000-103 |
| R102 | 15kQ, +5%, % W Resistor | 110000-152 |
| 106 | 150.2, +5%, ¥ W Resistor | 110000-151 |
| R107, R109 | 1kQ, +5%, % W Resistor | 110000-820 |
| R108-R110 | 100 2, +5%, Ya W Resistor | 110000-820 |
| 1B | 2.2kQ, +2%, 15-Element, Dual-Inline Package Resistor Pack | 118003-222 |
| 1K | 2.2k2, +2%, 15-Element, Dual-Inline Package Resistor Pack | 118003-222 |
Sockets
| OF | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| aL | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 2M | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 2N | 24-Contact Medium-Iinsertion-Force Integrated Circuit Socket | 79-42C24 |
(Continued on next page)
3-50
Pole Position Maintenance, Repair, and Parts
Pole Position Video Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. |
| 36, 4E | 24-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C24 |
| 3F, 4F | 24-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C24 |
| 3N | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 4D | 24-Contact Medium-insertion-Force Integrated Circuit Socket | 79-42C24 |
| SL, 6L | 18-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C18 |
| 6N, 7N | 24-Contact Medium-insertion-Force integrated Circuit Socket | 79-42C24 |
| 7E | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 8N | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| TIN | 24-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C24 |
| 12J, 130 | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 12K, 13K | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 12L, 13L | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 12N, 13N | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 43H | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42028 |
Transistor
| Q4 | ‘Type-2N3904, 60 V, 1 W, NPN Transistor | 34-2N3904 |
Miscellaneous Test Points Acceptable substitute is part no. 020670-07 179051- 002
| wi, W2 | 00 Jumper Resistor | 110005-001 |
| Y1B | 24.576 MHz Crystal Acceptable substitute is part no. 144004-002 | 144004-003 |
3-51
Maintenance, Repair, and Parts Pole Position
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc.. Sunnyvale, CA This drawing is only Conditionally issued, and ‘neither receipt nor possession Inereo! confers ar transters any right in, oF license 10 use, the ‘subject matter of the drawing or any design or technica! intormation shown thereon, nor any right to reproduce this drawing or any patl thereot. Except for manutacture by vendors of Alar, Inc., and fo; manutacture under ihe corporalion’s written license, 1 right to reproduce this drawing 's granted or the subject matter thereo! unless by written agreement with 0: written permission from the corporation,
R24,10,7W)
Figure 3-21 Regulator/Audio II Printed-Circuit Board Assembly
US-Built Cabinet A035435-01 H
3-52
Pole Position Maintenance, Repair, and Parts
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the spe Gific written permission of Atari, nc., Sunnyvale, CA. This, drawing is only conditionally issued, and neither receipt nor possession thereof confers of transfers any right in, or license tc use, the subject matter of the drawing or any design or technical information shown thereon, nor any Tight to repreduce this drawing or ary pan thereot. Except for manufactute by vendors of Atari, Inc.,. and for manufac: ture under the corporation's written license, no right to reproduce this drawing is granted or the subject matter thereot unless by written agreement with or written permis sion from the corporation
R24, 30, 7Wy
Figure 3-22 Regulator/Audio Il Printed-Circuit Board Assembly
Ireland-Built Cabinet A035435-05 B
3-53
Maintenance, Repair, and Parts Pole Position
Regulator/ Audio Il PCB Assembly Parts List
Assemblies and components in the following parts list are shown in Figures 3-21 and 3-22.
| Designator | Description | Part No. |
Capacitors
For -01* and -05** versions
| C1 | 470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-250477 | |
| c2 | 0.001 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor | 122002-102 | |
| c8 | 0.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor | Acceptable substitute is part | 122004-224 |
no. 122002-104
| C13 | 1000 OF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-250108 |
For -01 version
| c3 | 0.1 nF, 50 V, Ceramic-Disc Axial-Lead Capacitor | 122002-104 | |
| C4 | 470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-250477 | |
| cS | 0.01 pF, 25 V Minimum, Ceramic-Disc Axial-Lead Capacitor | Acceptable | 100015-103 |
substitute is part no. 122005-103
| cé | 0.22 pF, 25 V, Ceramic-Disc Axial-Lead Capacitor | Acceptable substitute is part | 122004-224 |
no. 122002-104
| c7 | 0.001 yF, 25 V, Ceramic-Disc Axial-Lead Capacitor | 122002-102 | |
| C9, C10 | 3300 pF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-350338 | |
| ci | 0.1 nF, 50 V, Ceramic-Disc Axial-Lead Capacitor | 122002-104 | |
| C12 | 470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-250477 | |
| C14 | 0.01 uF, 25 V Minimum, Ceramic-Disc Axial-Lead Capacitor | Acceptable | 100015-103 |
substitute is part no. 122005-103
| C15 | 0.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor | Acceptable substitute is part | 122004-224 |
no. 122002-104
| C16 | 0.001 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor | 122002-102 |
| Ci7 | 0.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor | 122004-224 |
| C18, C19 | 3300 uF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-350338 |
| C20, C21 | 0.1 nF, 50 V, Ceramic-Disc Axial-Lead Capacitor | 122002-104 |
| C22, C23 | 1 pF, 50 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-500105 |
Diodes
For -01 and -05 versions
| CRI | Type-1N4002, 1 A, 100 V Silicon Rectifier Diode | 31-1N4002 |
| CR4 | Type-1N4002, 1 A, 100 V Silicon Rectifier Diode | 31-1N4002 |
Integrated Circuits
For -01 and -05 versions
| ai | Type-LM305, 5 V, Linear Voltage Regulator | 37-LM305, |
For -01 version
| Qs | Type-TDA2002A, 8 W, Linear Audio Amplifier Integrated Circuit | 137151-002 |
| Q7 | Type-TDA2002A, 8 W, Linear Audio Amplifier Integrated Circuit | 137151-002 |
(Continued on next page)
*Acceptable substitutes are A035435-02 or -04. **Acceptable substitutes are A035435-01, -02, or -04.
3-54
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Maintenance, Repair, and Parts
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL. Reproduction forbidden without the specific written permission of Aan, nc, Sunnyvale. CA This Grawing is Only conditionally 'ssued, and helther receipt nor possession theveo! confers or transfers any right in or icensevto use. the Subject matter of the drawing or any design or technical infor mation shown thereon, nor ary right to repreduce this drawing or any part theres’ Except for'manulacture by vendors aati Ine. and for manutacture under he corporation's written license. no ight 1 reproduce ths cvawing 's granted or the Subject matte’ thereat uniess by written agreerrant with oF written permission from the corporation
2240+ 2s CO c24 CU} c25 +o
os o=z GO} c33 Gi 34 fo eggee
beeeee iN é ; | Gora
Gites teikce
TeCi2 oes fifo ras fatbcie Goe7
co) opc2:
Gocai Gocaz Goc4+3 644, 470PF eass Dy cdc 470FF (0647 ,270R° Coc
sa Ccss
Figure 3-23 EMI Shield PCB Assembly A037667-01 C
3-56 Pole Position
Pole Position Maintenance, Repair, and Parts
EMI Shield PCB Assembly Parts List
Components in the following parts list are shown in Figure 3-23.
| Designator | Description | Part No. |
Capacitors
| C1-C5 | 0.1 pF, +80, -20%, 50 V Ceramic-Disc Radial-Lead Capacitor | 122002-104 |
| C6-C10 | 0.01 uF, +80, -20%, 25 V Ceramic-Disc Radial-Lead Capacitor | 122005-103 |
Acceptable substitute is part no. 122005-104
| C12 | 0.01 zF, +80, -20%, 25 V Ceramic-Disc Radial-Lead Capacitor | 122005-103 |
| C13-C15 | 0.1 pF, +80, -20%, 50 V Ceramic-Disc Radial-Lead Capacitor | 122002-104 |
| C16 | 0.01 pF, +80, -20%, 25 V Ceramic-Disc Radial-Lead Capacitor | 122005-103 |
| C17-C24 | 0.1 uF, +80, -20%, 50 V Ceramic-Disc Radial-Lead Capacitor | 122002-104 |
| C25 | 0.01 uF, +80, -20%, 25 V Ceramic-Disc Radial-Lead Capacitor | 122005-103 |
| C27-C31 | 0.01 uF, +80, -20%, 25 V Ceramic-Disc Radial-Lead Capacitor | 122005-103 |
Acceptable substitute is part no. 122005-104
| C32, C33 | 0.1 uF, +80, -20%, 50 V Ceramic-Disc Radial-Lead Capacitor | 122002-104 | |
| C34-C39 | 0.01 uF, +80, -20%, 25 V Ceramic-Disc Radial-Lead Capacitor | 122005-103 | |
| C40-C43 | 0.1 pF, +80, -20%, 50 V Ceramic- | Radial-Lead Capacitor | 122002-104 |
| C44 | 0.471 uF, +80, -20%, 100 V Ceramic-Disc Radial-Lead Capacitor | 122016-471 | |
| C45, | 1000 pF, 100 V Ceramic-Disc Radial-Lead Capacitor | 122016-102 | |
| C46, C47 | 0.471 uF, +80, -20%, 100 V Ceramic-Disc Radial-Lead Capacitor | 122016-471 | |
| C48 | 1000 pF, 100 V Ceramic-Disc Radial-Lead Capacitor | 122016-102 | |
| C53 | 1000 pF, 100 V Ceramic-Disc Radial-Lead Capacitor | 122016-102 | |
| C54, C55 | 0.1 uF, +80, -20%, 50 V Ceramic-Disc Radial-Lead Capacitor | 122002-104 |
Connectors
| P19 | 30-Pin Card-Edge Connector | Acceptable substitute is | 179073-030 |
part number 179046-030
| P20 | 44-Pin Card-Edge Connector | Acceptable substitute is | 179073-044 |
part number 179046-044
3-57
Maintenance, Repair, and Parts Pole Position
H. Power Supply Assembly
A021084-xx (Voltage plugs} 29-053 _ . E (Capacitor) &. 034544.01 (Fuse block cover)
79-4411001 (Fuse post) 78-70501SC (Capacitor bracket) 46-2017002 (Fuse)
29-053 (Capacitor) A035891-02 034482:02 \ (Fuse harness assy.) 5 : va 5 46-301203 @ (Fuse)
78-2708 (Bushing)
A034630-01 79-3208 (Filter Assy) (Fuse block) 7641.01 78-70501SC bet pnata 46-2014002 (Bracket) (Fuses)
7915021001 ‘A035890-01 (Terminal block) \ (Power harness) 3A-MDA3501 © foramen) (Rectifier)
Figure 3-24 Power Supply Assembly freland-Built Cabinet A037671-05 J US-Built Cabinet A037671-10 J
3-58
Pole Position Maintenance, Repair, and Parts
Power Supply Assembly Parts List
Assemblies and components in the following parts list are shown in Figure 3-24.
Part No. Description (Reference Designations in Bold)
| A021084-01 | Voitage Plug for 100V | (90-110 VAC) | (violet) |
| A021084-02 | Voltage Plug for 120V | (105-135 VAC) | (yellow) |
| A021084-04 | Voltage Plug for 220V | (200-240 VAC) | (biue) |
| A021084-05 | Voltage Plug for 240V | (220-260 VAC) | (brown) |
A034629-01 AC Harness Assembly
| A034630-01 | RFI Filter Assembly | (FL1—designation not marked) | |
| A035888-01 | Upright and Cabaret Transformer Assembly | (T1) | Acceptab/e substitute is part no. A035888-02 |
A035890-01 Power Harness Assembly (J2) A035891-02 Fuse Harness Assembly (F2-F6)
| 29-053 | 27,000 pF 15V DC Electrolytic Capacitor | (C1) |
3A-MDA3501 Bridge Rectifier, Type MDA 3501 (CR1)
| 46-2017002 | 7A, 250 V, 3AG Slow-Blow Glass Cartridge-Type Fuse | (F1) |
| 46-301253 | 25 A, 32 V, 3AG Slow-Biow Glass CartridgeType Fuse | (F3) |
78-2708 Nylon Type 6/6 Hole Bushing with %-Inch Inside Diameter x 5544-Inch Outside Diameter x Ya-Inch Thick 78-70501SC. 2-Inch Diameter Capacitor Mounting Bracket (C1)
| 79-15021001 | 2-Circuit Single-Row Terminal Block | (located under F4) |
79-3206 5-Position 3AG Fuse Block with %-Inch Quick-Disconnect Terminals (F2-F6) 79-4411001 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post (F1) 034482-02 Power Supply Chassis 034544-01 Fuse Block Cover (F2-F6)
| 037639-03, -04 | Label for Fuse Vaiue | (Ff) |
| 037641.01 | Label for Fuse Values | (F2-F6) |
037671-04 power supply has the 120 V plug. A037671-05 has the 100 V, 220 V and 240 V plugs. A037671-06 has the 220 V and 240 V plugs.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Pole Position 7th printing
YOUR COMMENTS, PLEASE!
Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below.
If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.
Page: Comments:
Fill in if you wish a reply:
Name.
Firm Oi Distributor
Address. Ci Operator City State Zip O Other. Area Code Phone
First fold
'No Postage Necessary it mailed in. the United States
PC
BUSINESS REPLY MAIL a
FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA =e POSTAGE WILL BE PAID BY ADDRESSEE PC Atari, Inc. PC Attn.: Field Service/Coin-Op Division ee P.O. Box 427
Sunnyvale, California 94086 Pl
Pe PC
Second fold — ~~ _
wo14 aBpa siyj adey
Pole Position 7th printing
YOUR COMMENTS, PLEASE!
Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below. No postage stamp is necessary if mailed in the U.S.A.
If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.
Page: Comments:
Fill in if you wish a reply
Name.
Firm 1 Distributor
Address C. Operator City State Zip U Other.
Area Code Phone
First fold
Atari Ireland Limited Attn.: Field Service/Coin-Op Division
Tipperary Town, Ireland
Attach Necessary Postage
Second fold
eBpe siyy edey 2wo4
GE PE GE PE ES,
> > > > >
Fdsee Nil Natee Nah | Satee, ae! Sata Nated
Warranty
Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays (in games supplied with displays) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted
If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
- Such products are returned prepaid to Sellers’ plant, and
- Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.
In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.
Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.
The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety
Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor
This document is and contains confidential trade secret information of Atari, Inc.
This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.
Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc. iz « © % ©
© = AN
ATARI, INC. 790 SYCAMORE DRIVE P.O. BOX 906 MILPITAS, CALIFORNIA 95035 408/942-3100 ¢ TELEX 35-7488