CATHODE RAY TOMES

Bass Fishing Upright

Sega Bass Fishing (Sega Enterprises, 1998) · Manual · 94 pages · 93 sections · original scan

Page 1

Bas SISHNG,

OWNER’S MANUAL STD VERSION

SEGA ENTERPRISES, USA

Page 2

Warranty

Your new Sega Product is covered for a period of 90 days from the date of shipment. This certifies that the Printed Circuit Boards, Power Supplies and Monitor are to be free of defects in workmanship or materials under normal operating conditions. This also certifies that all Interactive Control Assemblies are to be free from defects in workmanship and materials under normal operating conditions. No other product in this machine is hereby covered.

Sellers sole liability in the event a warranted part described above fails shall be, at its option, to replace or repair the defective part during the warranty period. For Warranty claims, contact your Sega Distributor.

Should the Seller determine, by inspection that the product was caused by Accident, Misuse, Neglect, Alteration, Improper Repair, Installation or Testing, the warranty offered will be null and void.

Under no circumstances is the Seller responsible for any loss of profits, loss of use, or other damages.

This shall be the exclusive written Warranty of the original purchaser expressed in lieu of all other warranties expressed or implied. Under no circumstance shall it extend beyond the period of time listed above.

Page 3

TABLE OF CONTENTS

INTRODUCTION OF THE OWNERS MANUAL

GENERAL PRECAUTIONS

NAUWRWNE

8.

9.

10.

12.

13.

. GAME BOARD

15.

16.

17. . PRECAUTIONS TO BE HEEDED FOR OPERATION

. NAME OF PARTS

. ACCESSORIES

. ASSEMBLY AND INSTALLATION

. PRECAUTIONS TO BE HEEDED WHEN MOVING MACHINE

. CONTENTS OF GAME

. EXPLANATION OF TEST AND DATA DISPLAY

7-1 COIN METER, INTERNAL SWITCHES, AND SWITCH UNIT

7-2 TEST MODE

7-3 MEMORY TEST

7-4 VIDEO MEMORY TEST

7-5 BOUNDRY TEST

7-6 INPUT TEST

7-1 OUTPUT TEST

7-8 SOUND TEST

7-9 C.R.T. TEST

7-10 TIMER TEST

7-11 GAME ASSIGNMENTS

7-12 COIN ASSIGNMENTS

7-13, VOLUME SETTING

7-14 BOOKKEEPING

7-15 BACKUP DATA CLEAR

CONTROL PANEL

8-1 GREASING

8-2 REPLACING THE EXTENSION SPRING

8-3 REPLACING THE TORSION SPRING

8-4 REPLACING THE VOLUME

8-5 REPLACING THE INTERNAL PARTS OF REEL

COIN SELECTOR

9-1 TAKING OUT THE COIN SELECTOR

MONITOR

10-1 CATUTIONS CONCERNING SAFE HANDLING OF MONITOR

10-2, CLEANING THE CRT SURFACES

10-3 ADJUSTMENT METHOD

10-4 REMOVAL/REPLACEMENT OF MONITOR

. REPLACEMENT OF FLUORESCENT LAMP AND DISPLAY CARD

11-1 REPLACEMENT OF FLUORESCENT LAMP

11-2 REPLACEMENT OF DISPLAY CARD

PERIODIC INSPECTION TABLE

TROUBLESHOOTING

14-1 REMOVING THE GAME BOARD

14-2 COMPOSITION OF THE GAME BOARD

DESIGN RELATED PARTS

PARTS LIST

WIRING DIAGRAMS 2~3

6~7

8~12

14~22

23~36

24~26

32-34

37~43

37~38

38~39

40~41

44~46

47~52

47~48

49~50

51~52

53~54

57~58

60~89

XXX

Page 4

Installation space:

Height:

Weight:

Power maximum current:

MONITOR: SPECIFICATIONS

37 in.(L) x 30 in.(W)

65 in.

Approx. 223 lbs.

1.8 Amp AC 120V 60 Hz

29” 3-mode scan display

INTRODUCTION OF THE OWNERS MANUAL

SEGA ENTERPRISES, LTD., has for more than 30 years been supplying various innovative and popular amusement products to the world market. This Owners Manual is intended to provide detailed descriptions together with all the necessary installation, game settings and parts ordering information related to the SEGA BASS FISHING U/R, a new SEGA product.

This manual is intended for those who have knowledge of electricity and technical expertise, especially in ICs, CRTs, microprocessors, and circuit boards. Read this manual carefully to acquire sufficient knowledge before working on the machine. Should there be a malfunction, non-technical personnel should under no circumstances touch the interior system. Should the need arise, contact our main office, or the closest branch office listed below.

SEGA ENTERPRISES, INC. (USA) Customer Service 45133 Industrial Drive Fremont, CA 94538 Phone 650-802-1750 Fax 650-802-1754 7:30 am - 4:00 pm, Pacific Standard Time Monday thru Friday

Page 5

General Precautions

Follow Instructions: All operating and use instructions should be followed. Attachments: Do not use attachments not recommended by the product manufacturer as they may cause hazards. Accessories: Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use only mounting accessories recommended by the manufacturer. Moving the Product: This product should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product to overturn. Ventilation: Slots and openings in the cabinet are provided for ventilation, to ensure reliable operation of the product and to protect it from overheating; these openings must not be blocked or covered. The openings should never be blocked by placing the product in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

Power Sources: This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your location, consult your local power company. For products intended to operate from battery power or other sources, refer to the operating instructions. Grounding or Polarization: This product is equipped with a three-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug. Power Cord Protection: Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. Overloading: Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

Object and Liquid Entry: Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. Servicing: Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. Damage Requiring Service: Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

  • If the power cord or plug is damaged;
  • If liquid has been spilled, or objects have fallen into the product;
  • If the product has been exposed to rain or water;
  • If the product does not operate normally when following the operating instructions. Adjust only those controls that are explained in the operating instructions. An improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation;
  • If the product has been dropped or damaged in any way;
  • When the product exhibits a distinct change in performance; this indicates a need for service. Replacement Parts: When replacement parts are required , be sure the service technician has used replacements parts specified by the manufacturer or that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
Page 6

Safety Check: Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. Heat: The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

Lithium Battery- Dispose of batteries only in accordance with the battery manufacturer’s recommendations. Do not dispose in an open flame condition, since the battery may explode. Cleaning: When cleaning the monitor glass, use water or glass cleaner and a soft cloth. Do not apply chemicals such as benzine, thinner, etc. Location: This an indoor game machine, DO NOT install it outside. To ensure proper usage, avoid installing indoors in the places mentioned below: + Places subject to rain/water leakage, or condensation due to humidity; In close proximity to a potential wet area;

  • Locations receiving direct sunlight;
  • Places close to heating units or hot air; eIn the vicinity of highly inflammable/volatile chemicals or hazardous matter;
  • On sloped surfaces; «In the vicinity of emergency response facilities such as fire exits and fire extinguishers;
  • Places subject to any type of violent impact;
  • Dusty places.

INSTALLATION PRECAUTIONS

  • Verify the amperage of the branch circuit outlet before plugging in the power plug. Do not overload the circuit.

+ Avoid using an extension cord. If one is required, use an extension cord of type SJT, 16/3 AWG rated min. 120 VAC, 7A.

  • Moving this unit requires a minimum clearance (of doors, etc.) of 32” (W) by 77” (H). ¢ For the operation of this machine, secure a minimum area of 32” (W) by 42”(D).

REGULATORY APPROVALS This game has been tested and found to comply with the Federal Communications Commission Rules. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This game has been tested and listed by Underwriters Laboratories, Inc., to ANSI/UL22.

LISTED

5K92

AMUSEMENT MACHINE

Page 7

1 . PRECAUTIONS TO BE HEEDED FOR OPERATION

In order to prevent accidents, be sure to comply with the following points before and during operation.

PRECAUTIONS TO BE HEEDED FOR OPERATION BEFORE STARTING THE OPERATION

@ In order to avoid accidents, check the following before starting the operation: Check if all of the adjusters are in contact with the surface. If they are not, the cabinet can move and cause an accident.

@ Do not climb on the product. Climbing on the product can cause falling

WARNING! down accidents. To check the top portion of the product, use a step. To avoid electric shock, check to see if door & cover parts are Locked.

To avoid electric shock, short circuit and or parts damage, do not put the following items on or in the periphery of the product:

Flower vases, flower pots, cups, water tanks, cosmetics, and receptacles/ containers/vessels containing chemicals and water.

To avoid injury, be sure to provide sufficient space by considering the potentially crowded situation at the installation location. Insufficient installation space can cause the player to come into contact with or hit others

CAUTION! and result in injury or trouble.

PRECAUTIONS TO BE HEEDED DURING OPERATION

To avoid injury and accidents, those who fall under the following catagories are not allowed to play the game: A\ * Intoxidated persons.

  • Those who have high blood pressure or heart problems.
CAUTION! * Those who have experienced muscle convulsion or loss of consciousness when playing video games, etc.
  • Persons susceptible to motion sickness.
  • Persons whose acts runs counter to the products warning displays.

fingers or extraneous matter in openings of the product or small openings in or around doors. To avoid falling down and injury resulting from falling down, immediatly stop the () To avoid electric shock and short circuit, do not allow customers to put hands and

CAUTION!

customer’s leaning against or climbing on the product, etc. To avoid electric shock and short circuit, do not allow the customers to unplug the power plug without a justifiable reason.

Page 8

2 .NAME OF PARTS

BILLBOARD (COVER)

CONTROL PANEL CONTROLLER,

CONTROL _PANEL BASE.

SERVICE DOOR FRONT

COIN CHUTE DOOR

CASHBOX DOOR

MAINTENANCE HATCH

REAR ~& aa COMMUNICATION PORT.

GAME SPECIFICATIONS WIDTH LENGTH HEIGHT WEIGHT

All measurements are in inches

WHEN ASSEMBLED 30” x 37” x 65” 223 LBS.

Page 9

3 . ACCESSORIES

DESCRIPTION OWNERS MANUAL

art No. (Qty.) 4201-6394-01 (1) lote Figures If Part No. has no description, the Number has not been registered or can not be registered. Such a part may not be obtainable even if the customer desires to purchase it. Therefore, ensure that the part is in safekeeping with you.

TORSION SPRING HOT-3015 (1) Spare

POP BSS STD 429-0620 (1) Adhere this onto the cabinet with double-sided tape. EXTENSION SPRING HOT-3107 (4)

VOL CONT B-5K OHM 220-5484 (1) Spare

Page 10

THE SHIPMENT METHOD DESCRIBED BELOW ONLY APPLIES TO ‘MODEL 3’ BOARDS CONTAINED IN THE

WARNING! FOLLOWING GAMES:

LOST WORLD, VIRTUA FIGHTER 3, SUPER GT, SEGA BASS FISHING, STRIKER 2, DAYTONA 2, RALLY, HARELY DAVIDSON

!'NEVER SHIP MODEL 3 GAME BOARDS

OUTSIDE OF CAGE!!

CARTON BOX 601-8928 (1) Used for transporting the GAME BOARD. {SUPPLIED WITH YOUR GAME}

DO NOT SHIP GAME BOARD WITHOUT THIS BOX AS IT MAY DAMAGE THE GAME BOARD AND VOID YOUR WARRANTY.

“CHECK SIDE” Display

FILTER BOARD

THEY MAY BE DAMAGED BEYOND REPAIR. PLEASE SHIP THEM

() NO OTHER GAMES BOARDS ARE TO BE SHIPPED IN THE CAGE AS

WITHOUT CAGE PROPERLY PROTECTED DURING SHIPPING.

WARNING!
Page 11
  • ASSEMBLING AND INSTALLATION
WARNING! Assembling should be performed as per this manual. Since this is a complex machine, erroneous assembling may cause damage to the machine, or malfunctioning to occur. When assembling, be sure to perform work by plural persons. Depending on the assembly work, there are some cases in which performing the work by a single person can cause personal injury or parts damage.

When carrying out the assembly work, follow the procedure in the following 4-item sequence:

1 | SECURING IN PLACE (ADJUSTER ADJUSTMENT)

POWER SUPPLY

TURNING POWER ON By} | Wy] } rm

ASSEMBLING CHECK

Note that the tools such as a phillips screwdriver and wrench for M16 hexagon bolt w/24 mm width across flats are required for the assembly work.
Page 12

1 SECURING IN PLACE (ADJUSTER ADJUSTMENT)

Be sure to have all the Adjusters make contact with the surface. Unless the Adjusters come into contact with the surface, the Cabinet

WARNING! can move of itself, causing an accident.

This machine has 2 each of casters and adjusters (shown below). When the installation position is determined, cause the adjusters to come into contact with the floor directly, make adjustments in a manner so that the casters will be raised approximately 5mm. from the floor and make sure that the machine position is level.

LEG ADJUSTER (2)

©) Move the machine to the installation position.

CASTER (2)

Q) Cause all of the leg adjusters to make contact

with the floor. By using a wrench, make adjustments in the height of the leg adjusters to ensure that the machine's position is level.

QB) After making adjustments, fasten the leg

adjuster nut upward and secure the height of the leg adjuster. BOTTOM VIEW

@) Depending on the floor surface status of the installation location, the Rear Cabinet may move of itself. As shown, the NON-SLIP SHEET is attached to the back side of the CAUTION MAT. Ensure that the Adjuster is installed in the manner to match the position of NON-SLIP SHEET

  • After making adjustments, fasten the adjuster nut upwards and secure the height of the adjuster

CASTER

FASTEN UPWARDS

Approx. 1/4” INCH

LEG ADJUSTER

Page 13

2 | POWER SUPPLY

@ Ensure that the power cord is not exposed on the surface (passage, etc.). If exposed, they can be caught and are susceptible to damage. If damaged, the cord can cause an electric shock or short circuit. Ensure that the wiring position is not in the customer's passage way

WARNING! or the wiring has protective covering.

The AC unit is mounted on the left side of Front Cabinet DX. The AC Unit incorporates the Main SW, Earth Terminal and Inlet. Firmly insert the Power Plug into the Socket Outlet and the other side of the plug to the Inlet. Turn the Main SW ON to turn power ON.

® Ensure that the Main SW is OFF. MAIN SW CIRCUIT PROTECTOR POWER | (o 3 (FUSE) CORD ol=

©O

@ Connect the Power cord to the Outlet customer’s passage way or wiring has O°

Socket. Ensure power cord is not in

protective covering.

3 TURNING POWER ON

To turn power on, turn the AC Unit’s Main SW on. The Billboard’s Fluorescent Lamp lights up and images will be outputted on the projector. Background music (BGM) is outputted during ADVERTISE from the speaker. However, this BGM is not emitted if “No BGM output during ADVERTISE” is set.

Page 14

ASSEMBLING CHECK

The TEST MENU allows for each part of the cabinet to be checked, the Monitor to be adjusted, and the coin and

game related various functions to be performed.

Va

Goop Goop Goop Goop Goop Goop Goop Goop Goop Goop Goop Goop Goop Goop Goop Goop Goop Goop Goop Goop CPU ROM TEST

(CROM03 BANK) (CROM02 BANK) (CROMO1 BANK) (CROM00 BANK) (CROMI3 BANK) (CROMI2 BANK) (CROMII BANK) (CROMIO BANK) (CROM23 BANK) (CROM22 BANK) (CROM21 BANK) (CROM20 BANK) (CROM33 BANK) (CROM32 BANK) (CROM3I BANK) (CROM30 BANK) (CROMB) (cRoM2) (cROM1) (CROMO)

PRESS TEST BUTTON TO EXIT Ica Ic2 Ic3 Ica Ics Ice Ic7 Ics Ico Ic.10 Ic Ic12 Ic3 Ica Ics Ic.16 Icy Ics. Ic19 1c20 ~

S Ne

INPUT TEST

CAST OFF

SELECT OFF SERVICE, OFF

COIN OFF

TEST OFF

RODX 80H RODY 80H REEL SPEED 80H STICK X 80H STICK Y 80H

PRESS TEST BUTTON TO EXIT \

XX

(—

Ne OUTPUTTEST

>AC MOTOR CLUTCH REEL BREAK

SELECT WITH SERVICE BUTTON AND

PRESS TEST BUTTON TO EXIT OFF OFF OFF /

\

y, Selecting the MEMORY TEST on the test mode menu screen causes the on-board memory to be tested automatically. The game board is satisfactory if the display beside each IC No. shows GOOD.

Selecting the INPUT TEST on the menu screen in the test mode to display the screen on which each SW and Volume is tested. Press each switch. (To check the Coin SW, insert a Coin from the inlet with the Coin Chute Door being opened.) If the display beside each switch is ON, the switch and wiring connection are satisfactory. Check the display of each Volume value. The Volume could have an irregularity caused by differences between machines and vibration during transportation. Set the Volume values by referring to Section ?

In the output test mode, carry out lamp test to ascertain that each lamp lights up satisfactorily.

Page 15

la

NS SOUND TEST

No (0)

SELECT WITH SERVICE BUTTON PRESS TEST BUTTON TO EXIT /

Va CRITEST 1/2

wg Wild

PRESS TEST BUTTON TO CONTINUE LL \

wy,

Ick Test 2p Ne

a

yy In the TEST mode, selecting SOUND TEST causes the screen, on which sound related BD and wiring connections are tested, to be displayed. be sure to check if the sound is satisfactorily emitted from each of speaker and the sound volume is appropriate.

In the TEST mode menu, selecting C.R.T. TEST allows the screen (on which the projector is tested) to be displayed. Although the projector adjustments have been made at the same time of shipment from the factory, color deviation, etc., may occur due to the effect caused by geomagnitism, the location building’s steel frames and other game machines in the periphery. By watching the test mode screen, make judgement as to whether an adjustment is needed. If it is neccessary, adjust the projector by refering to Section 9.

Perform the above inspections also at the time of monthly inspection.

Page 16

5 . PRECATIONS TO BE HEEDED WHEN MOVING THE MACHINE

@ When moving the machine, be sure to pull out the plug from the power supply. Moving the machine with the plug as is

WARNING! inserted can damage the power cord and cause a fire or electric shock. @ When moving the machine on the floor, retract the Adjusters and ensure that Casters make contact with the floor. During transportation, pay careful attention so that Casters do not tread power cords. Damaging the power cords can cause an electric shock and/or short circuit. @ When lifting the cabinet, be sure to hold the catch portions or bottom part. Lifting the cabinet by holding other portions can damage parts and installation portions, due to the empty weight of the cabinet, and cause personal injury.

Use care when handling glass made parts. When the glass is damaged, fragments of glass can cause injury

CAUTION!

LEG ADJUSTERS =

Page 17

6 .CONTENTS OF GAME

The following are operations and responses obtained when the machine functions satisfactorily. Any functioning different from the following may have been caused by a certain fault. Immediately investigate and eliminate the cause of malfunctioning to ensure satisfactory operation.

HOW TO PLAY

The ADVERTISE mode appearing on the screen before game play is comprised of the following:

SEGA LOGO]— [ADVERTISE] — [TITLE] -> [HOW TO OPERATE 1 t t RANKING] < [HOWTO OPERATE2] < [TITLE

In this game, satisfying the condition of “CLEAR WEIGHT” (the total weight of bass fished up) preset for each area within the time limit results ina STAGE CLEAR. If you continue when the time is up, however, the current total weight will remain effective. Clearing all of the Areas allows you to proceed to the Special Stage where huge bass reside. The player who fishes up big bass can rank among the BIG BASS RANKING players by entering his name.

This game employs an exclusively used Special Controller inclusive of the Game Start Button.

REEL ROD

(i Although not actually attached, this appears in the game mode.

HANDLE to be turned in the direction of arrow)

LURE CHANGE BUTTON, (yellow)

START/CAST BUTTON (red)

Page 18

® Insert a coin(s). Up to 9 credits can be counted at one time. Coins inserted after counting 9 credits will neither be counted nor returned.

@ Select a Fishing area from among the 3 Areas of Lake Paradise (a virtual lake). Choose with SELECT LEVER and decide by START/CAST button.

am SELECT AN AREA.

LODGE

CAPE

INLET

@ Then, select the LURE. Select with the SELECT LEVER and decide by START/CAST button. Each type of lure has specific characteristics (for example, some may be appropriate for a certain depth of water while others may be suitable for a specific action, time zone, or status of desired bass). By considering these factors, using lures in the most efficient manner will contribute to increasing the bass fishing-up rate. The characteristics of each type of lure are as follows:

Page 19

SPINNER BAIT (EASY) Attract bass with this bait while reeling at a constant speed, or stopping to reel sometimes to allow for blade glistening.

DEEP CRANK (EASY) This type is used for deep water. Have the lure hit the bottom and reel, then repeat real and stop action.

SHALLOW CRANK (EASY) This is used for shallow water. Have the lure hit the bottom and reel, then repat reel and stop motion.

Page 20

VIBRATION (EASY) Attract bass by reeling at the constant speed or having the lure hit an obstacle such as a stone, driftwood, etc. to cause irregular movements.

MINNOW/ JERK BAIT (NORMAL) Attract bass by reeling at a constant speed and jerking the rod to reel so that the lure will look like a small fish making a quick escape.

PENCIL BAIT (DIFFICULT) Attract bass to the water surface by reeling the rod while repeating the slightly twitching motion to have the lure look like a smalll fish of insects writhing on the surface.

Page 21

Remaining Line TIME LIMIT TOTAL WEIGHT

LINE OUT 2 TOTAL WEIGHT

6.6m rH Weight to 7 clear, Water temperature | W,TEMP 21°C g (Norm) clear/5,808g Name of Lure

Currently selected lure

Selected lure’s HOW TO OPERATE range of water depth. the selected lure.

Try to master the best lure and the most appropriate action to catch a big fish.

Page 22

After the lure is decided, set the CAST spot (where to cast the lure). Select with the SELECT LEVER and decide by START/CAST button. Press the START/CAST button to have the lure cast automatically (at this time the player does not have to do the cast movement).

T button

Currently selected lure

Having its own territory, a big fish is hiding at a certain point in each area depending on the time zone and water temperatures. Cast in various points and find where the big one is.

Page 23
  • When the lure hits the surface, turn the reel handle, move the rod, and activate the lure to attract bass.

LINE OUT 1 TOTAL WEIGHT

12.6m W,TEMP 21°C 8g MAGE IN WATER clear/5,@00g

When bass snaps at the lure, pull the rod towards you by hooking up.

For timely hooking.........FISH! is displayed. For untimely hooking.....MISS! is displayed.

For a successful hooking, HIT BONUS time is added depending on the size of the hit bass.

Page 24

©) When the bass is hooked, pull it towards you by paying attention to LINE TENSION METER.

LINE OUT 1' 3 5 Ht TOTAL WEIGHT

6.6m W,TEMP 21 3,460g clear/5,800g LINE

TENSION

WA Turn the rod downward.

LINE

If the line tension is too high, "Line's gonna break!" will be displayed.

If the line tension is too low, "Reel it in" will be displayed.

LINE TENSION METER

"Line's gonna break!" ea) Line s gonna

break!

Stop reeling and hold out! If not operated skilfully.

Reel and stretch =) 1

uN Cc) the line tight. =) Lost “Reel it in" If not operated skilfully.

Page 25

@ When the bass is fished up, the following 5-step display & WEIGHT to be added to the total weight are shown. Then, BONUS TIME is added depending on the weight of the bass.

SMALL ONE MEDIUM BIG ONE SUPER BIG RECORD SIZE

If the total wieght exceeds the Norm weight, the player can proceed to the next Area. The next Area will be determined automatically as shown.

() Clearing all of the Areas allows the player to proceed to the Special Area where lots of big ones are.

  • Everytime the player catches 4 basses, the Special Lure will be awarded. Continued use of the lure is allowed in cases of CONTINUE and AREA CLEAR.
  • When the player catches a big bass and ranks in the BIG BASS RANKING, he can enter his name. Only the Black Bass is counted for the ranking.
Page 26

. EXPLANATION OF TEST AND DATA DISPLAY

By operating the switch unit, periodically perform the tests and data check. When installing the machine initially or collecting cash, or when the machine does not function correctly, perform checking in accordance with the explanations given in this section. The following shows tests and modes that should be utilized as applicable.

TABLE 7 EXPLANATION OF TEST MODE

ITEMS DESCRIPTION SECTIONS

When the machine is installed, perform the following: INSTALLATION | |. Check to see that each setting is as per standard setting made 7-9, 7-10 OF MACHINE at the time of shipment.

2.In the INPUT TEST mode, check each SW and VR. 7-5

  • In the OUTPUT TEST mode, check each of lamps. 7-6
  • In the MEMORY TEST mode, check ICs on the IC Board. 7-3,7-4

MEMORY Choose MEMORY TEST in the MENU mode to allow the MEMORY test to be performed. In this test, PROGRAM RAMs, ROMs, and ICs on the IC Board are checked.

PERIODIC Periodically perform the following: SERVICING

  • MEMORY TEST 7-3,7-4
  • Ascertain each setting. 7-9,7 -10
  • In the INPUT TEST mode, test the CONTROL device 7-5
  • In the OUTPUT TEST mode, check each of lamps. 7-6
CONTROL1. In the INPUT TEST mode, check each SW and VR.7-5

SYSTEM

  • Adjust or replace each SW and VR. 8

3 If the problem can not be solved yet, check the CONTROL’s moves. 8

PROJECTORIn the PROJECTOR ADJUSTMENT mode, check to see if the7-8

PROJECTOR adjustment is appropriately made.

IC BOARD 1. MEMORY TEST

2.In the SOUND TEST mode, check the sound related ROMs. 7-7

DATA CHECKCheck such data as game play time and histogram to adjust the7-12

difficulty level, etc

Page 27

7-1 COIN METER, INTERNAL SWITCHES, AND SWITCH UNIT

COIN METER

If the COIN METER and the Game Board are electronically disconnected, game play is not possible.

IMPORTANT! Do not touch places other than those specified. Touching places

other than those specified can cause an electric shock or short circuit accident.

The Coin Meter is in the CASHBOX door.

CASHBOX DOOR.

SPACE FOR COIN METER 2 This coin meter 1s installed when the machine is connected with the other cabinet for versus play Coin Meter 2 counts the number of coins inserted in the other cabinet.

CASHBOX, Depending on the Game Board used, however,

the number of coins inserted in the other cabinet can not be counted by this coin meter.

COIN METER 1 (left-hand side) Counts the number of coins inserted.

INTERNAL SWITCHES

The Control Panel Base can be opened by unlocking the backside lock.

Switches and Knobs.

CONTROL PANEL BASE | {

Page 28

SWITCH UNIT

Never touch places other than those specified. Touching places not specified can cause electric shock and short circuit.

@ Adjust to the optimum sound volume by considering the environmental requirements of the installation location. @ |f the COIN METER and the game board are electrically disconnected,

IMPORTANT! game play is not possible.

The Control Panel Base can be opened by unlocking the backside lock. Internal switches will appear when the Base is opened

of] @ee t cate 3a ‘TEST BUTTON | como von

SERVICE BUTTON

oO) TEST SWITCH Allows for entering the Test Mode of Game BD.

@) SERVICE SWITCH SERVICE CREDIT SW. Used without registering on the Coin Meter.

@ SOUND VOLUME Adjust the Speaker Volume.

Page 29

DOOR SWITCH

When the service loor is removed, the door switch functions to turn power off automatically. To turn power on the with the service door as is removed, use the accessory Cheater as per the (1)-(2) procedure below.

DOOR SHITCH ~~ DOOR_SWITCH

S DTo insert. Cheater :

509-5276

@Turn 90 degrees.

Page 30

7-2 TEST MODE This mainly checks if the operation of the game BD is accurate, and allows for COIN ASSIGNMENTS/GAME ASSIGNMENTS setting and Projector adjustments. a TEST MENU >

(PU MEMORY TEST

  • Push the TEST BUTTON to cause the follow- VIDEO MEMORYTEST ing TEST MENU to appear: BOUNDRY SCAN TEST INPUT TEST

ourpurtest (2) By pushing the SERVICE BUTTON, bring the

a “>” mark to the desired item and press the TIMER TEST TEST BUTTON. This will select the item’s GAME ASSIGNMENTS COIN ASSIGNMNETS test. VOLUME SETTING pica bith Gah B) After the test is complete, move the “>” mark on to “EXIT” and press the TEST BUTTON to return to game mode. SELECT WITH SERVICE BUTTON

AND PRESS TEST BUTTON

FIG. 7.2 TEST MENU.

7-3 MEMORY TEST The MEMORY TEST mode is for checking the (— (CPU ROM TEST > on-BD memeory IC functioning.

soem._(cnomnanaNaIenbn“GOOD” is displayed for normal ICs and “BAD
GoD—_(CROM02 BANK)1c2tensisdi‘;
SceD(CRONE HANasomeis displayed for abnormal ICs
GOOD(CROMO0 BANK)Icapoets
GOOD(CROMI3 BANK)Icstones
Good(CROMI2 BANK)Icstonne
Good(CROMII BANK)Ic7tenes
Good(CROMIO BANK)Icstoreiastarts ¢‘.:
‘epep)(CRONE BAN)a4wensThis test starts immediately after selection from
aSeenthe menu in the test mode. When in execution, the
coopIeraves“2.:*
G00D:_(CROMS3RANK)TeitonneTESTING NOW” message will be displayed at
GOOD(CROM32 BANK)rarysve,>;;
coed(CROMBTRANK1e1ssosenthe lower part to the screen. Press the Test Button
GOOD(CROM30 BANK)Ic16sone
sooo,_(CHOMS)mennto proceed to CPU RAM TEST
Goop—_(CROM2)Icstoes
GoopROM)Icstener
GOOD(ROMO)120teen

FIG. 7.3a MEMORY TEST

Test starts immediately after proceeding to this Goop (SDRAM) Ics Ic.1s mode from CPU ROM TEST. During execution, Goon SORAMD tS AShortca, cs00 the “TESTING NOW” message will be displayed at the lower part of the screen. When an error occurs, the ERROR message is shown. After finising the test, press the TEST button to return to the menu mode.

FIG. 7.3b MEMORY TEST

Page 31

7-4 VIDEO MEMORY TEST

a

Goop Goop coop Goop coop Goop coop Goop coop Goop coop coop Goop coop coop coop VIDEO BOARD ROM TEST

(VROMO1) (CROMO0) (CROMO3) (cROMO2) (CROMOS) C30 (CROMO4)IC31 (CROMO7) 132 (CROMO8) C33 (CROMI) 134 (CROMI0) C35 (CROMI3)1C36 (CROMI2) 137 (CROMIS)IC38 (CROMI4) C39 (cRoMI7)1C.40 (CROMI6) ICAI

PRESS TEST BUTTON TO CONTINUE ~

FIG. 7.4a VIDEO MEMORY TEST Va

Ne VIDEO BOARD RAM TEST

PRESS TEST BUTTON TO CONTINUE ~S\

FIG. 7.4b VIDEO MEMORY TEST

7-5 BOUNDRY SCAN TEST

Va

XN BOUNDRY SCAN TEST

PRESS TEST BUTTON TO EXIT \

/ FIG. 7.5 BOUNDRY SCAN TEST This allows the functioning of the VIDEO MEMORY IC’s on the IC board to be checked. “GOOD” is displayed for normal IC’s and “BAD” is displayed for abnormal IC’s if any.

Test starts immediately after proceeding to this mode from the menu in the test mode. During execution, the “TESTING NOW” message will be didplayed at the lower portion of the screen. After fininshing the test, press the TEST BUTTON to proceed to VIDEO RAM.

Test starts immediately after proceeding to this mode from the VIDEO BOARD ROM TEST. During execution, the “TESTING NOW” message will be displayed at the lower portion of the screen. If staus is satisfactory, nothing will be displayed. After fininshing the test, press the TEST BUTTON to return to the menu mode.

Selecting the “BOUNDRY SCAN TEST” causes the Game board’s testing in terms of hardware to be performed automatically.

When the test is completed, if the results are as shown left, it is satisfacory.

After finishing the test, press the TEST BUTTON to have the MENU MODE return on the screen. Next, turn power off and then turn it back on again. To avoid malfunctioning, have the Board intialized by turning the power off and then on.

If there is any hardware problems, an error message is displayed. Please contact the offices herein stated or where the product was purchased from.

Page 32

7-6 INPUT TEST

a INPUT TEST \

cast orF SELECT OFF COIN OFF SERVICE OFF TEST OFF

RODX 80H RODY 80H REEL SPEED 80H STICK X 80H STICK Y 80H

FIG. 7.6 INPUT TEST

7-7 OUTPUT TEST

a OUTPUT TEST

>AC MOTOR OFF CLUTCH OFF REEL BREAK OFF

EXIT

SELECT WITH SERVICE BUTTON AND \

/ FIG. 7.7 OUTPUT TEST

7-8 SOUND TEST

(— sounp Test

NO 000

SELECT WITH SERVICE BUTTON \

yy FIG. 7.8 SOUND TEST @ This test mode displays the status of each switch, button, and Volu me. When the switch/button corrsponds to the name of the item is pressed, if OFF changes to ON, it is satisfactory. When corresponding Volume is operated, if the Volume value differs in a natural manner, it is satisfactory.

APPROPRIATE VALUE OF TENSION VOLUME

r ) Tension volume values are displayed in hexadecimal

numerals within the range of OOH~ffH. If the value does not satisfy the following limitations, adjust the Volumes gear mesh so as to meet the requiremnts.

MIN. LIMIT: Over20H MAX. LIMIT: Under e0H

@ RODX, ROD Y: Volumes which detect reel (rod) operation. REEL SPEED: Volume which detects handle operation. 80H when not turned. @ STICK X, STICK Y: Volume which detects Select Lever operation.

Choose OUTPUT TEST to cause the following lower screen to appear. In this test, check the status of each lamp.

@ By using the Service Button, select the desired item and execute the test by pressing the test button to shift OFF to ON. Selecting another item by using the Service Button shifts ON to OFF. Bring the arrow to exit and press test button to return to the menu mode.

@ AC MOTOR: The motor inside the Control Panel. with ON the motor rotates. CLUTCH: Clutch mechanism inside Control Panel. With ON, GRIP operation becomes weightier. @ REEL BREAK: REEL BRAKE which is in the mechanism inside the Reel Handle. With ON, handle operation becomes weightier.

This enables sound used in the game to be checked. Sound related memory and each speaker are checked.

r ) Press the SERVICE BUTTON to increse the number by one

and the sound corresponding to the number will be emitted.

Note that No. 000 does not emit any sound.

@ _ Bring the “>” to EXIT and press the TEST BUTTON to return to the MENU MODE.

Page 33

7-9 CR.T. TEST

a

XX nn om (i

ei PRESS JEYT BUPTPN TH GRIT FIG. 7.9 C.R.T. TEST

7-10 TIMER TEST

Va

XX TIMER TEST \ 1997, 10/31 (FRI) 00:00:00

BATTERY OK

YEAR 1997 MONTH 10 DAY 31 HOUR 00 MINUTE 00 SECOND 00

SET DEXIT

FIG. 7.10 TIMER TEST Select C.R.T. TEST to cause the MONITOR to display the screen shown left, allowing MONITOR adjustment status to be checked.

Periodically check the MONITOR adjustment status on this screen.

The screen (1/2) enables color adjustment check to be performed. The color bar of each of the 4 colors, i.e..red, green, blue, and white, is the darkest at the extreme left and becomes brighter towards the extreme right.

Press the TEST BUTTON to shift to the next screen (2/2).

The screen (2/2) allows screen size and distortion to be tested.

Check if the CROSSHATCH FRAME LINE goes out of the screen and if the crosshatch lines are distorted.

Press the TEST BUTTON to return to the MENU mode.

This test mode allows the setting of year, month, and day, as well as built-in battery, and real time clock to be checked.

@ Press the Service Button to bring the arrow to the setting item.

@ Press the Test Button to set the desired value for each item.

@ Press the Service Button to move the arrow and bring it to SET, then press the test button to change to the set value.

@ Bring the arrow to EXIT and press the test button to return to the menu mode.

Page 34

7 - 11 GAME ASSIGNMENTS

Selecting the GAME ASSIGNMENTS in the MENU mode causes the present game settings to be displayed and also the game settings changes (game difficulty, etc.) can be made. Each item displays the following content.

SETTING CHANGE PROCEDURE

Gror Setting changes cannot be stored unless the TEST BUTTON is pressed

while the arrow is on EXIT. PORTANT!

  • Press the SERVICE BUTTON to move the “>” to the desired item.
  • Choose the desired setting change item by using the TEST BUTTON.

@ To return to the MENU mode, move the arrow to EXIT and press the TEST BUTTON.

a GAME ASSIGNMENTS \ @ ADVERTISE SOUND eee Oh asar Determines wether ADVERTISE SOUND is to be emitted or not by the setting to ON when emitting it and to OFF when not emitting it. EXIT

@ GAME DIFFICULTY Sets the Game Difficulty in 5 catagories from | to

  • The greater the number is, the higher the difficulty level becomes. Alternately it may display each catagory by name; Very Easy, Easy, Normal, Hard, Very Hard COUNTRY TYPE: *##%

SELECT WITH SERVICE BUTTON

The Following FIGURES/TABLES show the factory recommended settings.

Page 35

7 - 12 COIN ASSIGNMENTS

The “COIN ASSIGNMENTS” mode permits you to set the start number of credits, as well as the basic numbers of coins and credits. This mode expresses “how many coins correspond to how many credits.”

SETTING CHANGE PROCEDURE

Gror Setting changes cannot be stored unless the TEST BUTTON is pressed

while the arrow is on EXIT.

RTANT!

oO) Press the SERVICE BUTTON to move the arrow to the desired item. @ Choose the desired setting change item by using the TEST BUTTON.

@ To return to the MENU mode, move the arrow to EXIT and press the TEST BUTTON.

/ COIN ASSIGNMENTS \

COIN CHUTE TYPECOMMON@COIN CHUTE TYPE
CORES ETOSTSRETCREIETSSets the combination of the number of COIN CHUTEs and

CREDIT TO CONTINUE — 1 CREDIT 4 the number of players as applicable. In the case that the COIN/CREDIT SETTING #1 A a x COIN CHUTE is changed, be sure the setting is made in a

CHUTEALICONTCREDITmanner meeting the replaced coin chute.
CHUTE1COIN1 CREDITCOMMON:

Coins are accepted in common for both players.

MANUAL SETTING

INDIVIDUAL: >EXIT Each player uses a coin chute which accepts coins independently.

SELECT WITH SERVICE BUTTON LS ‘AND PRESS TEST BUTTON yy,

@ CREDITTO START Number of credits required for starting game (1~5 credits are selected.)

@ CREDITTO CONTINUE Number of credits required for continuing game (1~5 credits are selected.)

@ COIN/CREDIT SETTING Sets the CREDITS increase increment per coin insertion. There are 27 setings from #1 to #27, expressed in XX CREDIT as against XX COINS inserted. (TABLE 7.9a, 7.9b) #27 refers to FREE PLAY. When the COIN CHUTE TYPE is set to INDIVIDUAL, there are some setting numbers not displayed as indicated in TABLE 7.9b.

@ MANUAL SETTING This allows credit increase setting as against coin insertion to be further set in the manner finer than COIN/ CREDIT SETTING (refer to TABLE 7.9c).

Page 36

TABLE 7.12a COIN/CREDIT SETTING (COIN CHUTE COMMON TYPE)

SETTING FUNCTIONING OF CHUTE#1

SETTING #11 COIN1 CREDIT
SETTING #21 COIN2 CREDITS
SETTING #31 COIN3 CREDITS
SETTING #41 COIN4 CREDITS
SETTING #51 COIN5 CREDITS
SETTING #61 COIN2 CREDITS
SETTING #71 COIN5 CREDITS
SETTING #81 COIN3 CREDITS
SETTING #91 COIN4 CREDITS
SETTING #101 COIN5 CREDITS
SETTING #111 COIN6 CREDITS
SETTING #122 COINS1 CREDIT.
SETTING #131 COIN1 CREDIT
SETTING #141 COIN2 CREDITS
SETTING #151 COIN1 CREDIT

2 COINS 3 CREDITS

SETTING #161 COIN3 CREDITS
SETTING #173 COINS1 CREDIT
SETTING #184 COINS1 CREDIT
SETTING #191 COIN1 CREDIT

2 COINS 2 CREDITS 3 COINS 3 CREDITS 4 COINS 5 CREDITS

SETTING #201 COIN5 CREDITS
SETTING #215 COINS1 CREDIT
SETTING #221 COIN2 CREDITS
SETTING #232 COINS1 CREDIT

4 COINS 2 CREDITS 5 COINS 3 CREDITS

SETTING #241 COIN3 CREDITS
SETTING #251 COIN1 CREDIT

2 COINS 2 CREDITS 3 COINS 3 CREDITS 4 COINS 4 CREDITS 5 COINS 6 CREDITS

SETTING #261 COIN1 CREDITS

SETTING #27 FREE PLAY

Page 37

MANUAL SETTING

>EXIT

NS COIN TO CREDIT

BONUS ADDER

COIN CHUTE #1 MULTIPLIER L.COIN COUNTS AS 1 COIN COIN CREDIT

COIN CHUTE #2 MULTIPLIER I COIN COUNTS AS 1 COIN COIN CREDIT MANUAL SETTING

1COIN —-LCREDIT.

NO BONUS ADDER —]

2345678
203456789
203456789
23456789

/ SELECT WITH SERVICE BUTTON

AND PRESS TEST BUTTON

FIG. 7.12b MANUAL SETTING

@ Determines Coin/Credit setting.

@ This sets how many coins should be inserted to obtain one Service Coin. Selecting MANUAL SETTING in the COIN ASSIGNMENTS mode displays the following screen. -)--0

@ This sets how many tokens one coin represents.

Table 7.12c MANUAL SETTING

COIN TO CREDIT 1 COIN 1 CREDIT. 2 COINS 1 CREDIT. 3 COINS 1 CREDIT. 4 COINS 1 CREDIT. 5 COINS 1 CREDIT. 6 COINS 1 CREDIT. 7 COINS 1 CREDIT 8 COINS 1 CREDIT. 9 COINS 1 CREDIT.

BONUS ADDER NO BONUS ADDER 2 COINS GIVE 1 EXTRA COIN 3 COINS GIVE 1 EXTRA COIN 4 COINS GIVE | EXTRA COIN 5 COINS GIVE | EXTRA COIN 6 COINS GIVE | EXTRA COIN 7 COINS GIVE 1 EXTRA COIN 8 COINS GIVE 1 EXTRA COIN 9 COINS GIVE 1 EXTRA COIN

COIN CHUTE MULTIPLIER 1 COIN COUNTS AS 1 COIN 1 COIN COUNTS AS 2 COINS 1 COIN COUNTS AS 3 COINS 1 COIN COUNTS AS 4 COINS 1 COIN COUNTS AS 5 COINS 1 COIN COUNTS AS 6 COINS 1 COIN COUNTS AS 7 COINS 1 COIN COUNTS AS 8 COINS 1 COIN COUNTS AS 9 COINS

Page 38

7-13 VOLUME SETTING

This allows Slide Volume to be set.

VOLUME SETTING ‘AUTO SETTING

PULL POSITION SWING POSITION REEL MAX dd (df). MIN 74 (75) MAX 98 (95) MIN 07 (03) NEUTRAL 88 (88)

>CONTINUE WITH SAVE CONTINUE WITHOUT SAVE

SELECT WITH SERVICE BUTTON "AND PRESS TEST BUTTON Fig. 7.13a VOLUME SETTING

VOLUME SETTING MANUAL SETTING

TENSION

STICK X

STICK Y

MAX da (de) MIN 07 (06) MAX ao (aB) MIN 61 (62) NEUTRAL 82 (83) MAX af (al) MIN 66 (63) NEUTRAL 84 (84)

>EXIT WITH SAVE EXIT WITHOUT SAVE

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON Fig. 7.13b VOLUME SETTING Settings of volumes, etc., can be executed. Volume setting has 2 catagories, i.e., AUTO SETTING and MANUAL SETTING. AUTO SETTING performs the setting of the Volume of the portions that can be set automatically. MANUAL SETTING executes the setting of the Volume of the portions that can only be set manually. Selecting VOLUME SETTING causes AUTO SETTING to be executed first.

AUTO SETTING

AUTO SETTING starts of itself. By holding the rod, when the line is pulled, move the rod forward so that the line will be withdrawn up to the limit. If the length is short, “LINE ERROR” occurs. When “LINE ERROR” occurs, check to see if the length of the knotted portions at both ends of the line is appropraite or not by referring to Section 8. If the “LINE ERROR” still occurs when the length of the knotted portions is appropriate, then replace the line. During setting, “AUTO SET- TING NOW” is displayed. When setting is finished, “AUTO SETTING COMPLETE’ and each Volume value are displayed. By using the Service Button, select CONTINUE WITH SAVE, press the Test Button to have the results stored, and proceed to the next mode.

Page 39

7 - 14 BOOKKEEPING Choosing BOOKKEEPING in the MENU mode displays the data of operating status up to the present are shown on 2 pages. Press the TEST BUTTON to proceed to PAGE 2/2.

/BOOKKEEPINGTAGE>@COIN CHUTEM:

COIN REPORT Number of coins put in each Coin Chute.

COIN CHUTE #1 XXXXXXXXXXX

COIN CHUTE #2XXXXXKXXKEX@TOTAL COINS:

TOTAL COINS XXXXXKXXXKX woe .

COIN CREDITSXXXKXKXKXKKTotal number of activations of Coin Chutes.

SERVICE CREDITS XXXXXXXXXXX TOTAL CREDITS XXXXXXXXXXX

NUMBER OF GAMES @ COIN CREDITs:

1 P.GAMESXXXXXXXXXXXNumber of credits registered by inserting coins.

2 PGAMES: XXXXXXXXXXX NUMBER OF CONTINUE

1 PGAMESXXXXXXXXXXX@SERVICE CREDITS:

2 PGAMES XXXXXKXXXKX, : : Credits registered by the SERVICE BUTTON.

TOTALTIMEXDXXHXXMXXS
PLAYTIMEXDXXHXXMXXS
AVERAGE PLAYTIMEXXMXXS@TOTAL CREDITS:
LONGEST PLAYTIMEXXMXXSTotal number of credits (COIN CREDITS+SERVICE
SHORTETEST PLAYTIMEXXMXXSCREDITS)
XYPRESS TEST BUTTON TO CONTINUETD@ TOTAL TIME:

FIG. 7.14a BOOKKEEPING (1/2) The total energized time.

aBOOKKEEPINGPAGE 22 \

TIME HISTOGRAM XXXXXXXX XXXXXXXX XXXXXXXX On page (2/2), each play frequency is displayed. When XXXXXXXX etting diffi ev e re

SECGOOKX setting difficulty levels, the frequency can be refered to as a

IMI0s ~ IM19SXXXXXXXXstandard.

M208 ~ 1295 XXXXXXXX MOS ~ 1M395 XXXXXXXX

IMdos ~ 1M49SXXXXXXXXWhen in the PAGE 2/2 mode, press the TEST BUTTON to

IMS0S ~ 1MS9S XXXXXXXX

4M00s ~ 409sXXXXXXXXreturn to the MENU mode.

4ML0S ~ 4M198 XXXXXXXX

4M20S~ 4298XXXXXXXX

4M30S ~ 4398 XXXXXXXX 4Ma0s ~ 4M49S XXXXXXXX 4MS0S ~ 4MS9S XXXXXXXX sMO0S ~ XXXXXXXX

NePRESS TEST BUTTON'TO EXITyy,

FIG. 7.14b BOOKKEEPING (2/2)

7-15 BACKUP DATA CLEAR Clears the contents of BOOKKEEPING and high BACKUP DATA CLEAR .

/—>score player ranking entry.
oenay@When clearing, bring the arrow to “YES” and when

not clearing, to “NO”, by using the SERVICE BUTTON, and push the TEST BUTTON.

@ = When the data has been cleared, “COMPLETED”

will be displayed. Bring the arrow to “NO” and press the TEST BUTTON to cause the MENU mode to return on to the screen.

@ Note that the contents of the GAME SETTING, SELECT WITH SERVICE BUTTON COIN SETTING, and BOARD SETTING are not

LOmess esr BeTONToryyaffected by BACKUP DATA CLEAR operation.

FIG. 7.15 BACKUP DATA CLEAR,

Page 40

8 . CONTROL PANEL

before performing work by touching the interior parts of the product.

WARNING! @ Be careful so as not to damage wirings. Damaged wiring can cause an electric shock . or short circuit accident. Work should be performed by Location’s Maintenance Man or the Serviceman. Performing work by non-technical personnel can cause electric shock or short circuit accident. A @ In order to prevent an electric shock and short circuit, be sure to turn power off

impact to the parts and Control Panel. Careless working can cause injury and or

A When performing work, use extreme care so as not to exert excessive load or

deformation, damage and loss of parts.

CAUTION!

The Control Panel of this product has the mechanism in which the motor, clutch, volume, etc. are used. Periodically check the Control Panel in the Test Mode to see if there is any fault, and cope with the problem if any at an early stage. Also, once a month, apply greasing to the mechanism part.

8 - 1 GREASING

Once a month, open the Control Panel and apply greasing to the mechanism part. For Spray Grease, Use Grease Mate (Part No. 090-0066).

GEAR MESH PORTION

Page 41

INSIDE, GUIDE PLATE

As shown in the PHOTO, insert the Spray Grease Nozzle to the inside of Guide plate and apply grease to the sliding friction portions of the part.

8 - 2 REPLACING THE EXTENSION SPRING

In the case the centering action (to return to the center position) of the reel (rod) is inactive, the cause may be the secular change of or damage to Extension Spring and Torsion Spring. Replace the Extension Spring in the following procedure. Prepare a Spanner (width across flats: 5mm), narrow-edged flat blade type screwdriver, and Philips type screwdriver (M3 and M4 screws).

SCREW (2) M36, w/flat & spring washers

@® Turn power off and open the Control Panel.

Secure Pin Head with Spanner.

EXTENSION SPRING ; . , HOT-3107 @® By securing the pin head with spanner, remove the 2 screws with screwdriver and remove the Spring.

Page 42

@ By using the narrow-edged flat @ Take out the 34 screws and remove blade type screwdriverr remove the Guide Plate. the E rings.

E RING (2) M4

® Remove the 2 pins. Use care so as not to © Remove the two E-Rings and the Spring. lose the Collar.

@ Replace the Spring. By refering to the ASSY DRAWING HOT-3100, install the Spring, E-Ring, Washer, etc. in the correct sequential order.

Page 43

8 - 3 REPLACING THE TORSION SPRING

In the case the centering action (to return to the center position) of the reel (rod) is inactive, the cause may be the secular change of or damage to Extension Spring and Torsion Spring. Replace the Extension Spring in the following procedure. Prepare a Philips type screwdriver for M4 screw, a Hexagon Wrench (width across flats: 2mm), and a screw driver for M4 Hexagon Nut (width across flats: 7mm).

@_ Turn power off and open the Control Panel.

@ _ Take out 2 screws and remove the Volume together with the Bracket.

@ _ Take out the 2 set screws and remove the Gear.

Page 44

@ Take out the 2 Hexagon Nuts and remove the Pillow Block and Torision Spring.

HEXAGON NUT _(2) M4

When removing the Pillow Block, be sure to remove the straight from the Shaft. Removing it in an inclined direction can make work more difficult and cause injury hazard. Also, this can cause the oppisite side Shaft to be subject to an excessive load and cause Shaft damage.

© Replace the Spring. Ensure that the longer part of the Spring is positioned to the Control Panel’s center side.

© __ Reassemble by using the oppisite procedure. Hang the longer art_on this hook.

Page 45

8-4 REPLACING THE VOLUME

In the Test Mode, if the value variation of ROD X and ROD Y does not match with reel (rod) operation, the cause may be the Volume Gear Mesh failure, Volume damage, etc. Replace the Volume in the following procedure. Explanations of Volume replacement in the X direction are given below. The Volume in the Y direction is the one to be removed when replacing the Torsion Spring. Prepare a philips type screwdriver for M4 screw and flat-blade type screwdriver for M3 Cheese Head.

@® Turn the power off and open Control Panel.

@ Disconnect the Volume Connectors. The red one is the connector in the X direction, and the blue one is the Volume in the Y direction.

@ Take out the 2 screws and remove the Volume together with the Bracket.

@ Take out the 2 Set Screws and remove the Gear. SET SCREW (2) © Replace the Volume. Assemble by using the x6 oppisite procedure. At this time, cause the gears to be engaged in the periphery the center of the Volume’s movable range when the reel is positioned at the center. 220-5484

© Turn power on and perform Volume setting in the Test Mode.

Page 46

8 - 5 REPLACING THE INTERNAL PARTS OF REEL

Replace the internal parts of reel by using the following procedure. prepare a Philips screwdriver for M3 screw.

@®_ Turn the power off. @ Internal SW, etc. can be removed.

@® Take out 2 screws and remove Cover U.

COVER_U,

@ Remove the Connector and replace the Board.

© Assemble by using the oppisite procedure.

© Turn the power on and perform Volume setting in the Test Mode.

Page 47

9 .COIN SELECTOR

A

WARNING!

S

IMPORTANT! In order to prevent an electric shock and short circuit, be sure to turn power off before performing work by touching the interior parts of the product. Be careful so as not to damage wirings. Damaged wiring can cause an electric shock or short circuit accident.

When cleaning the Coin Selector, be sure to use a soft cloth. If the Coin Selector is badly soiled, remove the stains by using a soft cloth dipped in water or warm water and then squezzed dry. Never use chemical detergents or chemicals. If the Coin Selector is taken out for cleaning or checking, ensure that Coin Slector is accuratley functioning after it is returned in place.

The Coin Selector is employed for this product. If the Coin Selector’s coin passage is soiled, the coin selection accuracy is deteriorated. Be sure to perform cleaning once every 3 months. Although rarely, coin jam occurs in the periphery of the Coin Selector. Should coin jam occur, or for cleaning, take out the Coin Selector from the machine.

9-1 TAKING OUT THE COIN SELECTOR

@ Turn Power off.

@ Open the Coin Chute Door. |

@® While pulling the Coin Chute Bracket’s white

stopper, bend it towards the arrow direction shown.

O) First lift the Coin Selector up and then take it

out from the Bracket in the manner of pulling it diagonally upward.

STOPPER ra Bend towards if the arrow. |

Page 48

HANDLING THE COIN JAM

If the coin is not rejected when the REJECT BUTTON is pressed, open the coin chute door and open the selector gate. After removing the jammed coin, put a normal coin in and check to see that the selector correctly functions.

CLEANING THE COIN SELECTOR

©

Oo O Does the coin drop into the Cashbox correctly?

O Is the coin rejected when inserted while keeping

The coin selector should be cleaned once every 3 months. When cleaning, follow the procedure below: Turn the power for the machine OFF. Open the coin chute door. Open the gate and dust off by using a soft brush (made of wool, etc.). Remove and cleen smears by using a soft cloth dipped in water or diluted chemical detergent and then squeezed dry. Remove the CRADLE. When removing the retaining ring(Ering), be very careful so as not to bend the shaft. Remove stain from the shaft and pillow portions by wiping off with a soft cloth, ete. After wiping as per #5 above, further apply a dry cloth, etc. to cause the coin selector to dry completely.

Gror the coin selector

@ After cleaning the Coin Selecting, @ Never apply machine oil, etc. to

IMPORTANT! Insert a regular coin in the normal

working status and ensure that the Selector correctly functions.

COIN INSERTION TEST Once a month, when performing the COIN SW TEST, simultaneously check the following:

Does the Coin Meter count satisfactorily?

the REJECT BUTTON is pressed down? COIN METER

Page 49

OPTIONAL DOLLAR BILL ACCEPTOR

@ THE COIN DOOR ASSEMBLY USED ON SEGA BASS FISHING COMES EQUIPPED TO ACCEPT A DOLLAR BILL ACCEPTOR. ALL NEEDED WIRING CONNECTIONS ARE CONVIENENTLY LOCATED INSIDE THE GAME FOR THIS APPLICATION.

@ THE COIN DOOR CAN ACCCOMMODATE THE FOLLOWING VALIDATORS:

HOLE POSITION#1 VFMS (MARS)

(FORWARD-MOST POSITION)

HOLE POSITION#2 VFM2 (MARS)

VFM4 (MARS)

DBV45 (JCM)

HOLE POSITION #3 CURRENTLY NOT USED

HOLE POSITION #4 DSIO1*

*The back flange on the chute can be removed for hold position #4. If the flange is not removed, it may interfere with the back of the cabinent.

Page 50
  • MONITOR

10 - 1 CAUTIONS AND WARNINGS CONCERNING SAFE HANDLING OF MONITOR

CAUTION! When performing such work as installing and removing the monitor, inserting and disconnecting the external connectors to and from monitor, be sure to disconnect the power connector (plug) before starting work. Proceeding the work without following this instruction can cause electric shock of malfunctioning. Using the monitor by converting it without obtaining a prior permission is not allowed. SEGA shall not be liable for any malfunctioning and accident caused by said conversion.

SECONDARY SIDE (Chassis, sheet metal work, CRT, etc.) Primary side and secondary side The monitor’s circuit which is divided into the Primary side and secondary side, is electrically isolated. Do not touch the primary side and the secondary side simultaneously. Failing to observe the instruction can cause electric shock, and this is very dangerous. SECONDARY SIDE When making monitor adjustments, use a non- (Chassis, CRT) conductive driver and make adjustment without touching any other part other than the Adjustment V.R. and Knob. Also, be sure not to cause a shortcircuit to the Primary side and the Secondary side. If short-circuited, it can cause electric shock or malfunctioning, which is very dangerous.

High tension Voltage Some of the parts inside the monitor are subject to high-tension voltage in excess of 20,000 volts and very dangerous. Therefore, do not touch the monitor interior. Should soldering & paper wastes, etc. be mixed in the monitor, turn the power off so as not to cause malfunctioning or fire hazard.

ANODE CAP. PRIMARY SIDE DEMAGNETIZER REAR PART ANODE LEAD | MAIN BD Approx. 29 kV

FBT. Approx. 29 KV FOCUS LEAD

Approx. 10 kV

Disconnect or unplug

Connecting the CRT and PCB For combining the CRT and PCB, use the specified part No. to maintain the status of adjustments made at the factory. The anode of the CRT itself will be accumulitavely charged as time elapses, generating high tension voltage which is very dangerous. The monitor should be used with the Chassis, CRT and PCB assembled. When repair, etc. is required at the time of malfunctioning, be sure to send it in an “as assembled” condition. If these are disassembled, what’s charged to said high tension voltage can be discharged, causing a very hazardous situation. Therefore, under no circumstances should it be disassembled.

CAUTION! Static Electricity Touching the CRT surface sometimes causes you to slightly feel electricity. This is because the CRT surfaces are subject to static and will not adversly affect the human body. Installation and removal Ensure that the Magnetizer Coil, FBT (Fly-Back Transformer), Anode Lead and Focus Lead are not positioned close to the sheet metal work’s sharp edges, etc. and avoid damaging the insulated portions so as not to cause an electric shock and malfunctioning. (For the name of parts, refer to the above figures.)
Page 51

For the purpose of static prevention, special coating is applied to the CRT face of this product. To protect the coating, pay attention to the following points. Damaging the coating film can cause electric shock to the customers. For the caution to be heeded when . clearing, refer to the Section of Periodic Aluminum Foil inspection Table. 5 Do not apply or rub with a hard item (a rod with pointed edge, pen, etc.) to or on C.R.T. surfaces. Avoid applying stickers, seals, etc. on the C.R.T. face. Do not remove aluminum foils from the C.R.T. corners. Removing the aluminum foils can cause static prevention effects to be lowered.

CAUTION!

10 - 2 CAUTIONS TO BE HEEDED WHEN CLEANING THE CRT SURFACES

ing, pay attention to the following points. Peeling off static prevnetive coat can cause electric shock.

IMPORTANT! @ Remove smears by using a dry, soft cloth (flannels, etc.). Do not

use a Coarse gauze, etc. @ For smear removing solvent, alcohol (ethanol) is recommended. When using chemical detergent, be sure to follow instructions below: *Dilute chemical detergent with water and dip soft cloth in and then thoroughly wring it to wipe smears off. *Do not use a chemical detergent containing an abradant, powder or bleaching agent. *Do not use alkaline chemical detergents such as “glass cleaner” available on the market or solvents such as thinner, etc. @ Do not rub or scratch the CRT face with hard items such as brushes, scrub brush, etc. S Static preventive coating is applied to the CRT surfaces. When clean-

Page 52

10 - 3 ADJUSTMENT METHOD

Monitor adjustments have been made at the time of shipment. Therefore do not make further adjustment without a justifiable reason. Adjusting the monitor which contains high tension parts is dangerous work. Also, an erroneous adjustment can 1 cause deviated synchronization and image fault, resulting in malfunctioning.

CAUTION! To determine whether or not the adjustment is needed, make judgment by watching the monitor’s adjustment screen of the replaced Game Board. Normally, monitor adjustment is made with knobs and switches on the Adjustment Board that can be seen by opening the Control Panel Base. Note that in the monitor of this product, correct images can not be obtained unless the settings of the horizontal frequency or video input connector (input impedance/input level) are compatible with the board. When the Game Board is replaced, check the settings.

AMP_6P Connector Disconnect if the video input connector is D-SUB MINI 15P.

‘The Connector Plate can be

seen by removing the Mask

CONNECTOR PLATE.

i ® CONTROL PANEL BASE mS Sa

‘Since Knobs (2) and (3) are used as is adjusted at the time of shipment, they are covered from the point of design.

@® CONTRAST (VR282) @ _ R-GAIN (VR280) D B-GAIN (VR281) @ BRIGHT (VR283)

Adjusts image contrast.Turing this to the rightTuming this to the rightThis adjusts the on-
will result in the redwill resuit in the bluescreen image
color becoming darker.color becoming darker.brightness.

@® H. SIZE (VR284) @® H. POSITION (VR285) © V. SIZE (VR286) ® V-POSITION (VR287)

The horizontal imageThe horizontal image’ sThe vertical imageThe image’ s vertical
dimension is adjustable.position is adjustable.dimension is adjustable.Position is adjustable.

@ Mode Change SW (SW281) Sets horizontal frequency and video input connector.

First unplug the plug and then operate the switch. Operating the switch as is energized can cause damage and malfunctioning. Connect only the video input connector which is set in the maner consistent with the Game Board, Connecting any one other than the set connector or setting from the predetermined setting can cause malfunctioning.

Video input connector Input impedance/input level $ Ww 3 When npg D-SUB MINI ISP 750 Vp- When imate AMP OP frequency 24 kHz and video input 2k. /3.0Vp-p connector 1s D-SUB MINI 15P. rere co 24 kHz mode 31 kHz mode

Page 53

Use the knobs and connectors that can be seen by removing the Maintenance Hatch on the backside of the cabinet, normally as is at the time of shipment. In particular, do not touch the knobs not explained herein. When replacing the Game Board or the Monitor, ensure that the direction of the connector’s connection is correct as per the Game Board manual. If the connecting direction is wrong, the image is inverted or turned as shown below.

MAINTENANCE HATCH

A

@ R-CUT OFF (VR201) Turning this to the right will result in the red color becoming darker. @ G-CUT OFF (VR202) Tuming this to the right will result in the green color becoming darker. @ TRAP (VR451) ® _V-LIN (VR286) Controls trapezoidal Controls vertical distortions. linearity.

[| Q@CN401 NORMAL | (CN401 REVERSE ey

The image displayed is normal.

Am image which 1s tumed a 180 degrees 1s displayed. 2% H-SIZE CHANGE TAP (CNS09 : WIDE/NARROW) D-SUB_MINI_15P_ CONNECTOR Tsconnect this if the Video Input Connector

® sPc(vr4s2) Controls pincushion distortion. ® B-CUT OFF (VR203) Tuming this to the right will result in the blue color becoming darker.

® Focus To be adjusted to the best status.

( SCREEN Adjusts to the CUTOFF point.

DEFLECTING YOKE POLARITY CHANGE CONNECTOR 19 CN4O1 NORMAL CONNECTION ®D CN4O01 REVERSE CONNECTION aol usol

BROWN GRAY GRAY BROWN CNAOT nar 48 CNSOL NORMAL CONNECTION ‘UB CNSOI REVERSE CONNECTION Q501 Q501 () BLUE RED RED BLUE CNSOL CNSOL After H. SIZE is adjusted. if the size is still narrow, or if the horizontal lineality becomes worse (shrinkage of central portion) in the signal in which the horizontal display period is narrow. change the TAP to WIDE side. However. this is effective only in the case where the horizontal frequency is 15.75 kHz.

Page 54

10 - 4 REMOVAL/REPLACEMENT OF MONITOR

When performing such work as monitor installation/removal, or inserting/disconnecting the external Connector connected to the monitor and its interior, first be

WARNING! sure to disconnect the power connector (plug). Working with the power plug as is connected can cause electric shock or malfunctioning. When replacing the monitor, be very careful. To avoid electric shock, etc., personnel other than those who have technical expertise are not allowed to replace the monitor. Perform the assembly work by following the procedure herein stated. Failing to comply with the instructions can cause an electric shock. Be sure to use 2 or more persons for replacing the monitor. performing the replacement work by only one person can cause injury or parts damage. To ensure performing the work safely, provide sufficient space. Working in places with narrow space can cause injury or working errors. Be careful so as not to damage wirings. Damaged wiring can cause an electric shock or short circuit accident. Do not touch places other than those specified. touching places not specified can cause an electric shock or short cicuit accident.

Gror After the vertical/horizontal transposition of the MONITOR, monitor adjustments may be required.

IMPORTANT!

For performing the monitor’s vertical/horizontal transposition in the manner consistent with the Game Board, follow the procedure below:

® After turning the AC Panel’s main SW off,

unplug from the Socket Outlet. @ Open the Control Panel Base. Hexagon Nut (4) Pull the knob in the square hole inside the base Spring washer used:

downward. The lock will be unlocked and the Mask can be removed.

6) When the Mask is removed, the Connector Plate

appears. If the CRT is positioned horizontally, the Connector Plate is underneath the CRT, and if the CRT is positioned vertically, it is on the right hand side. Disconnect all of the connectors connected to the Connector Plate. ® If the monitor’s video input connector is D-SUB MINI connector, disconnect by removing the Maintenance Hatch on the backside of the cabinet.

6) Remove the nuts and spring washers which

secure the 4 corners of the monitor.

Page 55

® By holding the Monitor’s sheet metal

portion, pull out the monitor from the cabinet. Since the Monitor is a heavy item, be sure to use 2 workers to perform this work.

@ When installing the monitor to the cabinet, to position the CRT vertically, ensure the Connector Plate is on the right-hand side of the CRT and position the CRT horizontally, ensure the Connector Plate is underside the CRT.

Positioning Positioning © Install the Spring and Nut for the the CRT horizontal ly the CRT vertically monitor’s four corners.

® In the manner consistent with the :

: : \ LATE. Game Board setting, connect the video CONNECTOR I

input connector, and make connector connection with the other 2 connectors of the Connector Plate.

Mask Holder J Insert into the Mask Slits. woe /

©) Operate the mode change switch in the

manner consistent with the Game Board setting.

© Install the mask. Insert the 2 Mask holders which are projecting from the upper part of the Front Piece’s Mask installation portion into the Mask’s 2 slits, and press the Mask’s underside in.

Page 56
  • REPLACMENT OF FLUORESCENT LAMP AND DISPLAY CARD

@ When performing the work, be sure to turn power off. Working with power on can cause an electric shock or short circuit accident. @ The Flourescent Lamp, when it gets hot, can cause burns. Be very careful when replacing the Fluorescent Lamp.

To perform work safely and securely, be sure to prepare a step which is in a secure and stable condition. Not using a step or using an unstable step can cause a violent falling down accidents.

CAUTION!

11 -1 REPLACEMENT OF FLUORESCENT LAMP

  • Take off the 2 screws which secure the Holder on the upper part of Billboard.

@ Take out the billboard from the cabinet and replace the fluorescent lamp (20W)

FLUORESCENT LAMP 20H, daylight type TRUSS SCREW (2) 74 390-5251-20-02 W5X12, chrome plated y,

  • S_/” CLOW LAMP oN / 390-5638-1E

BILLBOARD PANEL

BILLBOARD COVER

Page 57

11 - 2 REPLACMENT OF DISPLAY CARD

To be performed if Display Card is damaged or if Game Board is replaced.

DISPLAY CARD.

® Turn Power off. BILLBOARD PANEL

@ Remove the 2 truss screws which secure the Billboard Cover.

@ Remove the Billboard Cover diagonally upward. / BILLBOARD _COVER_/ @ The Display Card is adhered to the backside of the Billboard Panel inside the Billboard cover.

© Peel off the Display Card and adhere the replacement Display Card. The adhesive tape is on the Display Card surface.

Page 58
  • PERIODIC INSPECTION TABLE The items listed below require periodic check and maintenance to retain the performance of this machine and ensure safe operation.

the plug is securley inserted, dust is accumulated between the Socket Outlet and the Power Plug, etc. Using the product with

WARNING! dust as is accumulated can cause a fire or electrical shock. @ Periodically once a year, request the place of contact herin stated

f) @ Be sure to check once a year to see if Power Cords are damaged,

or the Distributer, etc. where the product was purchased from, as regards the interior cleaning. Using the product with dust as is

accumulated in the interior without cleaning can cause a fire or

accident. Note that cleaning the interior parts can be performed on a pay-basis.

ITEMS DESCRIPTION PERIOD REERENCE

CHASSIS Volume V.R. inspection Monthly 1

Greasing to gears and pillows | Semi-annually

Memory Test Monthly 1

Setting Check Monthly

CONTROL MECHASW Volume inspectionMonthly7
(pole)Line InspectionMonthly8

Line Replacement Semi-annually | 8

COIN SELECTORCheck COIN SWMonthl7

COIN SELECTOR cleaning __| Trimonthly 9

MONITORScreen cleaningWeekly10
Check adjustmentsMonthly4,7,10
GAME BDSetting checkMonthly7
INTERIORCleaningAnnuallysee above.

POWER PLUG Inspection and cleaning

CABINET SURFACESCleaningAs necessary | see below
Page 59

13 . TROUBLESHOOTING Should trouble occur, first check connector connections.

PROBLEMS CAUSE COUNTERMEASURES

With Main SW ON, no activation Power is not supplied.

Power supply/voltage is not correct.

AC main fuse causes the power to be cut off due to momentary overload. Plug in correctly

Make sure that power supply/voltage is

Check fuse. Remove the cause of overload and replace fuse

Rod Controller’s Movements are unsatisfactory Volume Setting Failure

Encoder malfunctioning The fuse is blown due to an overload. Brake malufunctioning Thermal element functioned Perform Volume setting

Replace Encoder. Replace Fuse. Replace Brakes Activates @70°C, recovers after cool-off.

Irregular sound emitted from inside Rear Cabinet Greasing to gear mesh portion is not satisfactory, or extraneous matter mixed in. Apply greasing or eliminate extraneous matter.

The color of the image on PROJ. screen is incorrect. Connector connections are defective. Check the connection for the RGB and SYNC connectors of the PROJ. TERM. BD and VPM BUFFER BD.

screen has color deviation. The image on PROJ. Affected by the magnetic field of installation location. Make CONVERGENCE adjustment. (Refer to Section 9.)

No sound is emitted. Sound Volume adjustment is not appropriate.

Sound BD and speaker are malfunctioning. Adjust sound volume. (see Section 6).

Perform sound test to find and replace defective parts.(Refer to Section 6).

Lateral mecha does not function. Motor’s Overheat. Motor replacement is needed. (Check Motor Driver as this may be malfunctioning.)

The Fluorescent lamp does not light up. The Fluorescent tube is burnt out. Replace the Fluorescent tube (Refer to Section 10).

Switches of Control Panel do not function correctly Connection fault of connector between Front and Rear Cabi. Accurately connect the connector.

Page 60
  • GAME BOARD
WARNING! @ In order to prevent an electrical shock, be sure to turn power off before performing work by touching the interior parts of the product. @ Be careful so as not to damage wirings. Damaged wiring can cause an electric shock or short circuit accident.
CAUTION! time of shipment. Do not expose the Game BD, etc. without a good reason. In this product, setting changes are made during the test mode. The Game BD need not be operated. Use the Game BD, etc. as is with the same setting made at the

The Game Board replacement method depends on the type of the present Game Board and that of the Game Board to replace with. Herein, how-to-remove the previously installed Game Board is explained. Regarding the method of connecting the Game Board for replacement, refer to the instructions of that particular Game Board. When replacing the ST-V cartridge, first take out the Game Board from the cabinet as per the following procedure. Changing the cartridge within the cabinet can damage parts and wirings.

Note that when the Game Board is replaced, the monitor’s frequency change, video input connector’s reinsertion, and screen adjustment may be needed.

14-1

®

2)

@ TAKING OUT THE GAME BOARD

Turn Power off.

Remove the Service Door.

Disconnect all the connectors connected to the Shield Case. In the case of the Game Board for which the Shield Case is not used, disconnect all of the connectors connected to the Game Board.

Remove the Wing Bolt which secures the Base Board mounting the Shield Case (Game Board)

Pull out the Base Board with the Shield Case (Game Board) as is mounted, from the cabinet. At this time, to avoid wiring damage, use care so that wires are not caught. SERVICE DOOR

WING BOLT M4 x 20

Page 61

© Take Out the 3 screws and the Shield Case Lid to remove the Game Board.

14-2 COMPOSITION OF GAME BOARD

GAME BD BSS (833-13317)

@834-13318 ROM_BD_BSS

@©837-11858 MODEL 3 CPU BD COM

@837-11859 MODEL 3 VIDEO BD COM

[No. | PART No. __|_ DESCRIPTION | © | 9837-11858 MODEL3 CPU BOARD COM | @ | 837-11859 MODEL3 VIDEO BOARD COM 834-13318 ROM BD BSS

NOTE: THIS PICTURE IS FOR REFERENCE ONLY!! UNIT IS NOT TO BE OPENED. EXPOSING THE GAME

BD FOR ANY REASON MAY VOID WARRANTY.

Page 62

15 . DESIGN RELATED PARTS

DISPLAY CARD BSS STD. 429-0619-01

STICKER SIDE LEFT HOT-1119 STICKER SIDE RIGHT HOT-1118

STICKER SIDE LEFT 2 HOT-1124

STICKER SIDE RIGHT 2 HOT-1123

PLAY INSTR SH BSS STD, 422-0684-01

SUB INSTR $H BSS STD 422-0685-01

Page 63
  • PARTS LIST

TOP ASSY GET BASS STD

20: SAW 0: aS 34 BY (iol Jae

IO

aI

Sn Zo —s

Page 64

TOP ASSY GET BASS STD

ITEM NO.

wns PART NO.

HOT-10002 HOT-3000-01 HOT-3080 HOT-0001 HOT-0002 HOT-0003 HOT-0300 422-0684-01 422-0685-01 429-0619-01 260-0074 260-0075 032-000420 031-000416-0C 050-F00400 000-P00408-W 000-P00330 DESCRIPTION

ASSY CABINET 24K 750 OHM HC ASSY FISHING CTRL PNL HOT EXP ASSY VOLUME X REINFORCE BRKT L. REINFORCE BRKT R FAN BRKT ASSY SHIELD CASE BSS STD W/BASE PLAY INSTR SH BSS STD EXP SUB INSTR SH BSS STD EXP DISPLAY CARD BSS STD EXP FAN MOTOR DC24V 2410NL-05W-B50 FAN MOTOR DC24V 2410ML-05W-B50 WING BOLT M4X20 CRG BLT CRM M4X16 FLG NUT M4 M SCR PH W/FS M4X8 M SCR PH M3X30

Page 65

ASSY SHIELD CASE BSS STD W/BASE (HOT-0300)

ITEM NO.

we PART NO.

HOT-0310 105-5246 105-5247 HOT-0101 HOT-4500 DESCRIPTION

ASSY SHIELD CASE BSS STD SHIELD CASE BRKT W SHIELD CASE BRKT N WOODEN BASE DRIVER UNIT

Page 66

ASSY SHIELD CASE BSS STD (HOT-0310)

ITEM NO. PART NO. DESCRIPTION

1105-5240YSHIELD CASE MODEL 3
2105-5242X-01SHIELD CASE LID MODEL 3
3839-0951FILTER BD MODEL 3 JPT
4833-13416GAME BD BSS STD
101260-0064FAN MOTOR DC12V
Page 67

ASSY SHIELD COVER (HOT-1004)

ITEM NO. PART NO. DESCRIPTION

1200-5258MONITOR SHIELD
2200-5506SHIELD STAY LONG
201000-P00408-WM SCR PH W/FS M4X8
Page 68

ASSY FRONT CABI (HOT-1100)

z

FE)

€

= € § ‘Accessory for 200-5503)

Page 69

ASSY FRONT CABI (HOT-1100)

ITEM NO. PART NO.

HOT-1101X HOT-1102 HOT-1103X, HOT-1104 HOT-1105 HOT-1108 HOT-1109 HOT-1110 HOT-1112 HOT-1113 CQN-1313 HOT-1200 BOX-CASH HOT-1116 HOT-1270 HOT-1250 HOT-1119 HOT-1120 HOT-1121 HOT-1202 839-0894 HOT-1125 220-5420 601-6999 601-8810 509-5028 509-5453-V-B 601-8726 130-5156 509-5762 509-5763 000-T00512-C 012-T00410-0C 012-P00312 010-P00406-F 012-F00310 047-PA3207-6 000-P00512-W 000-F00410 000-F00308 012-P00316 012-P00412 012-P00410 012-P00306 DESCRIPTION

FRONT PIECE BILLBOARD COVER BILLBOARD PNL MASK HOLDER UPPER REINFORCE SPEAKER BRKT MIDDLE FRAME LOCK UNIT COIN CHUTE BD HOLDER UPPER LOCK BRKT ASSY CASH BOX DOOR CASHBOX COIN CEILING ASSY COIN CHUTE DOOR ASSY SERVICE DOOR DOOR SW BRKT REINFORCE PLATE R REINFORCE PLATE L. FRAME CASH BOX DOOR TERMINAL BD SPACER RHEO STAT 100 OHM 10W KNOB 18 SERRATION KNOB MR-1512-1T SW PB IM SW ROCKER J8 V-B CATCH F SPEAKER BOX 8 OHM LINE INTERRUPT SWITCH LINE INTERRUPT SWITCH M SCR TH CRM M5X12 TAP SCR TH CRM 4X10 TAP SCR PH 3X12 S-TITE SCR PH W/F M4X6 TAP SCR FH 3X10 RVT OPEN TYPE AL 3.2X7.6 M SCR PH W/FS M5X12 M SCR FH M4X10 M SCR FH M3X8 TAP SCR PH 3X16 TAP SCR PH 4X12 TAP SCR PH 4X10 TAP SCR PH 3X6

Page 70

ASSY CASH BOX DOOR (HOT-1200)

ITEM NO. PART NO. DESCRIPTION

1HOT-1201CASH BOX DOOR
3220-5574CAM LOCK W/KEYS
4HOT-1203CENTER TNG
5HOT-1204SIDE TNG
202065-E00300E RING 3MM
Page 71

ASSY SERVICE DOOR (HOT-1250)

ITEM NO.

wns & PART NO.

HOT-1251 220-5575 DP-1167 HOT-1252X DESCRIPTION

SERVICE DOOR CAM LOCK MASTER W/O KEY TNG LKG PAPER INSULATOR

Page 72

ASSY COIN CHUTE DOOR (HOT- 1270)

ITEM NO.

2IDHAWNE PART NO.

CQN-1320X CQN-1321 CQN-1324 HOT-1271 HOT-1272 220-5208~ 220-5575 250-5043 DP-1167 010-P00306-F 010-P00408-F DESCRIPTION

COIN CHUTE DOOR ASSY REJECT LEVER ASSY COIN CHUTE BRKT REJECT LEVER FLAP COIN CHUTE REJR~ CAM LOCK MASTER W/O KEY REJECT BUTTON ASSY TNG LKG S-TITE SCR PH W/F M3X6 S-TITE SCR PH W/F M4X8

Page 73

ASSY REAR CABI (HOT-1300)

ITEM NO.

0. iy Bo PART NO.

HOT-1301 HOT-1304 HOT-1303 HOT-1305 012-T00410-0C 000-T00410-0C 000-P00412-WB DESCRIPTION

REAR PIECE MAINTENANCE HATCH LID COMMUNI PORT HANDLE COVER TAP SCR TH CRM 4X10 M SCR TH CRM 4X10 M SCR PH W/FS BLK M4X12

Page 74

ASSY REJECT LEVER (CQN-1321)

QL

Q

ITEM NO. PART NO. DESCRIPTION

1 CQN-1322 REJECT LEVER BRKT

2CyY-1032REJECT LEVER
3123-0035SHAFT
201069-0039ERING 3.2

ASSY COIN CHUTE BRKT (CQN-1324)

ITEM NO. PART NO. DESCRIPTION

1Cy-1009COIN CHUTE BRKT
2105-5041UPPER COIN CHUTE
3220-5272CHANNEL BRKT W/O SHUTE,
201010-P00408-FS-TITE SCR PH W/F M4X8
Page 75

ASSY FL (HOT-1350)

ITEM NO. PART NO. DESCRIPTION

1 HOT-1351 FLLID 101 LOCAL PURCHASE ASSY FL 20W SD W/CONN HIGH S 201 010-P00416-F S-TITE SCR PH W/F M4X16

Page 76

ASSY MASK (HOT-1400)

ITEM NO. PART NO.

HOT-1401 601-8725 HOT-1402 HOT-1403 012-P00310 Sawune Sy DESCRIPTION

MASK CATCH M PACKING L. PACKING S TAP SCR PH 3X10

Page 77

ASSY FISHING CNTRL PNL HOT EXP (HOT-3000-01)

Tai [ Se Soe ae 61 a | 18

ete kgf

Bouter La = M378 ®) _spotyseasing to eelvng and sling ton pas.

Page 78

ASSY FISHING CNTRL PNL HOT EXP (HOT-3000-01)

ITEM NO. PART NO.

HOT-3001 HOT-3002-01 HOT-3003X, HOT-3004 HOT-3005 HOT-3006 HOT-3007 HOT-3050 HOT-3008 HOT-3009 HOT-3010 HOT-3012 HOT-3013 HOT-3014 HOT-3100 HOT-3015 HOT-3016 HOT-3017 HOT-3018 BSS-2907 HOT-3020 HOT-3021 HOT-3022 HOT-3023 HOT-3060 HOT-3070 HOT-3024 HOT-3090 HOT-3025 BSS-3001Z BSS-3002Z BSS-3003 BSS-3004 BSS-3005 BSS-3006 BSS-3007 BSS-3008 BSS-3009 BSS-3010 BSS-3011 BSS-3012 BSS-3013 BSS-3014 BSS-3015 BSS-3016Y BSS-3017Y BSS-3018 BSS-3040 DESCRIPTION

CNTRL PNL BASE BSS CNTRL PNL PLATE BSS EXP PROTECT RING PILLOW BLOCK A PILLOW BLOCK B BEARING BRKT A CENTER SHAFT ASSY ROD SPACER PINA COLLAR A DOME SLIDE DOME BRKT ASSY GUIDE TOR SPRING SPRING HOOK PIN SPRING HOOK ROLLER GEAR LAST KEY 3X3X8 SIDE SHAFT GEAR M08Z20 GEAR M08Z60 BEARING BRKT B ASSY CLUTCH ASSY MOTOR GEAR ENCODER ASSY VOLUME ROD TIP COVER R COVER L COVER U COVER S BD HOLDER CAST SW CAP SELECT SW CAP JOY STICK CAP HANDLE BAR HANDLE PIN HANDLE GRIP ORIGINAL NUT M8 SPACER A SPACER B SPACER C HANDLE CAP FRONT RING FRONT RING SPRING ASSY BRAKE W/PS

Page 79

ASSY FISHING CNTRL PNL HOT EXP (HOT-3000-01)

ITEM NO. PART NO.

839-1003 839-1004 HOT-3026 HOT-3027 HOT-3028 HOT-3029 HOT-3030 HOT-3031 000-P00306-W 031-0004 16-0C 050-F00400 065-E00400 000-P00408-W 028-C00306-P 028-C00408-P 028-A00406-P 000-T00306-0U 000-T00308-0B 000-P00312-0B FAS-000037 FAS-000038 FAS-500006 028-A00306-P 000-P00304-0B 050-C00400-3C FAS-000045 060-F00500 060-F00400 060-S00400 050-H00400 050-F00500 028-C00410-P DESCRIPTION

STICK CONT BD. REEL SW BD PILLOW BLOCK C GEAR ENCODER 2 COLLAR L COLLAR S INNER RING

CAUTION RING SHEET M SCR PH W/FS M3X6 CRG BLT CRM M4X16 FLG NUT M4 ERING 4MM M SCR PH W/FS M4X8 SET SCR CH CUP P M3X6 SET SCR CH CUP P M4X8 SET SCR HEX SKT CUP P M4X6 M SCR TH UCRM M3X6 M SCR TH BLK M3X8 M SCR PH BLK M3X12 M SCR BLK M3X35 M SCR PH BLK M3X45 CAP NUT TYPE 3 BLK M3 SET SCR HEX SKT CUP P M3X6 M SCR PH BLK M3X45 CAP NUT TYPE3 CRM M4, M SCR PH W/S BLK M3X6 FLT WSHR M5 FLT WSHR M4, SPR WSHR M4 HEX NUT M4 FLG NUT M5 SET SCR CH CUP P M4X10
Page 80

ASSY BRAKE W/PS (BSS-3040)

TORQUE M3 Skgf-cm.

Details of PART A

ITEM NO. PART NO. DESCRIPTION

101 601-9942 POWDER BRAKE 0.1MM MITSUBISHI 103 512-5052-017 POLYSWITCH RXE017 104 310-5376 SILICONE SHEET 105 370-5165-01-91 ENCODER 100PULSE W/O CONN, 201 000-P00304-0B M SCR PH BLK M3X4.

Page 81

ASSY ROD (HOT-3050)

ITEM NO. PART NO.

HOT-3051 000-P00406-W 600-7016-014 DESCRIPTION

ROD M SCR PH W/FS M4X6. WIRE HARN ROD FLEX

Page 82

ASSY CLUTCH (HOT-3060)

Screw Fastening Torque

ITEM NO.

wre Screw | BoluNut | StudANut [Set Screw ]insert Nut]

25 | 20 18 MS [35 {| 60 [ 35 M6 | 60_| 100 | 90 MB. 200 | 160 M10 350 (kgf -cm)

PART NO.

HOT-3061 HOT-3062 HOT-3063 HOT-3064 601-10057 000-P00412-W 000-P00408-W 028-C00306-P 000-P00306-S DESCRIPTION

CLUTCH BRKT GEAR CLUTCH IN GEAR MO08Z28 SHAFT HOLDER PARTICLE CLUTCH M SCR PH W/FS M4X12 M SCR PH W/FS M4X8 SET SCR CH CUP P M3X6 M SCR PH W/FS M3X6

Page 83

ASSY MOTOR (HOT-3070)

Install the Capacitor with screw.

ITEM NO. PART NO. DESCRIPTION

1HOT-3071MOTOR BRKT
2HOT-3072GEAR M1Z22
101350-5535MOTOR AC100V 8W.
201028-C00408-PSET SCR CH CUP P M4X8
202000-P00412-WM SCR PH W/FS M4X12
Page 84

ASSY VOLUME X (HOT-3080)

ITEM NO. PART NO. DESCRIPTION

1 HOT-3081 VOL BRKT 2 601-5410 GEAR 15 FAI 6 101 220-5484 VOL CONT B-5K OHM 201 028-C00306-P SET SCR CH CUP M3X6

Page 85

ASSY VOLUME Y (HOT-3090)

ITEM NO. PART NO. DESCRIPTION

1 HOT-3081 VOL BRKT 2 601-5410 GEAR 15 FAI6 101 220-5484 VOL CONT B-5K OHM 201 028-C00306-P SET SCR CH CUP P M3X6

Page 86

ASSY GUIDE (HOT-3100)

ITEM NO.

OIA

ll PART NO.

HOT-3101 HOT-3102 HOT-3103 HOT-3104 HOT-3105 HOT-3106 HOT-3107 HOT-3108 HOT-3109 HOT-3110 HOT-3016 HOT-3017 000-P00408-W 060-F00500 065-E00400 000-P00306-W DESCRIPTION

GUIDE PLATE GUIDE HOLDER R GUIDE HOLDER L CUSHION PINB COLLAR B EXT SPRING ROLLER HOLDER STOP ROLLER PINC SPRING HOOK PIN SPRING HOOK ROLLER M SCR PH W/FS M4X8 FLT WSHR M5 E RING 4MM M SCR PH W/FS M3X6

Page 87

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 88

DRIVER UNIT (HOT-4500)

ITEM NO.

wns & PART NO.

HOT-4501 HOT-4502 HOT-4503 839-1031 838-9507 400-5368-03024 601-7467 000-P00312-W 000-P00408-W 010-P00312-F 010-P00320-F 000-P00320-W DESCRIPTION

DRIVER BASE DRIVER LID CONN BRKT ENCODER D/A BD CLUTCH & MOTOR CONTROL BD SW REGU LCA30S-24 L-LOCK BK M SCR PH W/FS M3X12 M SCR PH W/FS M4X8 S-TITE SCR PH W/F M3X12 S-TITE SCR PH W/F M3X20 M SCR PH W/FS M3X20

Page 89

ASSY CABINET 24K 750 OHM HC (HOT- 10002)

ee

O®

Page 90

ASSY CABINET 24K 750 OHM HC (HOT-10002)

ITEM NO.

eCmIANAWNE =5 PART NO.

HOT-1001 HOT-1100 HOT-1004 HOT- 1002 HOT-1300 HOT-1350 CQN-1003 HOT-1003X HOT-1400 HOT-1005-01 400-5325-02-91 400-5325-03 HOT-1006X. HOT-1007 HOT-15001 HOT-1008 HOT- 1009 SGM-4420 200-5710 200-5642-24 220-5569 220-5570 999-0169 999-0167 050-H01000 000-P00408-WB 012-P00520-0C 012-T00410-0C 000-P00420-W 000-P00308-W 030-000616-S 010-P00306-F 010-P00412-F 008-T00408-0C 060-S01000 000-P00412-WB 030-000625-SB 068-652016-0B 000-F00512 000-P00308-W DESCRIPTION

STUD BOLT ASSY FRONT CABI ASSY SHIELD COVER LOWER BASE ASSY REAR CABI ASSY FL GUTTER STEP ASSY MASK CONN PLATE CRT POWER SUPPLY UNIT EXP POWER SUPPLY UNIT EXP CONN BRKT PWR SPLY LID COIN CNTR ASSY HARD CONTROL BOX SHADE SW BD BRKT AIR CAP COVER 900X900X1800 ASSY CLR DSPL 29AUTO MS-2931-S ASSY CLR DSPL 29TYPE 24K 100V MAG CNTR W/CONN MAG CNTR W/CONN CASTER 2 1/2" LEG ADJUSTER HEX NUT M10 M SCR PH W/FS BLK M4X8 TAP SCR #2 PH CRM 5X20 TAP SCR TH CRM 4X10 M SCR PH W/FS M4X20 M SCR PH W/FS M3X8 HEX BLT W/S M6X16 S-TITE SCR PH W/F M3X6 S-TITE SCR PH W/F M4X12 TMP PREF SCR TH CRM M4X8 SPR WSHR M10 M SCR PH W/FS BLK M4X12 HEX BLT W/S BLK M6X25 FLT WSHR BLK 6.5-20X1.6 M SCR FH M5X12 M SCR PH W/FS M3X8

Page 91

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 92

ASSY HARD CONTROL BOX (HOT- 15001)

ITEM NO. PART NO. DESCRIPTION

1HOT-1501CONTL PNL LOWER
2HOT-1520LATCH N
3HOT-1503SHAFT
4HOT-1504LATCH HOLDER

5 220-5575 CAM LOCK MASTER W/O KEY

6HOT-1505LKG TNG
7HOT-1522HINGE BSS HOT
8HOT-1506CONTRL PNL UPPER
9HOT-1521LOCK BRKT LONG
10HOT-1508INSTRUCTION COVER
llHOT-1510SHEET INSTR SPACE
12HOT-1511TORSION SPRING
13HOT-1512XLATCH INSTR COVER R
14HOT-1513XLATCH INSTR COVER L
15220-5167~COIN ENTRY~
16HOT-1515SPONGE A
17HOT-1516SPONGE B
18HOT-1517SPONGE C
20HOT-1519SPONGE D
21421-9823SW INSTR HOT
Page 93

Come see Sega GameWorks Service Department’s Homepage

fedaaetsste bot oh

ericeee a tne ee st Do oT Pere | Pee ee es fmt on eee ie oe i OS es GN SS SE PD Pa Pel Mee Se ee ee oe pm ce ee om fo alee oo go: cell om 1 LL es PE at a a

ay Se Komen oop coms om = Lae a

Page 94

SEGA

SEGA ENTERPRISES, INC. (USA)

45133 Industrial Drive Fremont, CA 94538 415/650-802-1750 phone 415/650-802-1754 fax