CATHODE RAY TOMES

Arkanoid Tournament

Tournament Arkanoid (US, older) (Taito America Corporation (Romstar license), 1987) · Document · 16 pages · 17 sections · original scan

Page 1

ROMSTAR inc.

TOURNAMENT

/ARIKAIN©ULD™

Instruction Manual

Romstar, Inc. 3043 Kashiwa Street, Torrance, CA 90505 Phone (213) 5392744 Fax (213) 5393626 Telex 182426

Licensed From TAITO™ All Rights Reserved ©1986

Page 2

Before You Get Started. . . Stop!

1, Does your new game package inciude all listed parts? {Is it complete?) 2 Isthe game you Nave chosen to transform abie to supply all the required voltages for the new game?

Note: Some games, [ie Ms Pac Man, Galaxian, etc.) regulate their voltages on the main PC B. This makes the existing power supply inefficient. These games will require a change in power supply for yournew game Many game supply houses can offer you a switching requiated power supply for a relatively tow cost
  • Isthe monitor configuration compatible? In most games it is rather difficult to change the monitor from a vertical mount to a horizontal Mount. We recommend you choose a game cabinet with the same mount as your new game requires 4 Do you have the necessary tools? (See the recommended tool! list)

Caution

F.C.C. Reguiation Compliance

The PC, board cage supphed with this new game kit must be utilized and terminated to ground at the time of installation. This 1s to avoid radio frequency radiation and d.comply with the limits for a class

“A computing device pursuant to sub-part ‘J’ of part 15. of FCC. ules, which are

designed to provide reasonable protection against interference when operated ina commercial environment. Operation of this equipment in a residential area is likely t to cause interférence

  • in which case, the user at nis own expense, will be required to take whatever measures may be required to correct the interference. Metalized FCC compliance label must be attached and visible on the outside of the cabinet (rear) upon completion of installation.
Page 3

Installing and Servicing Your

TOURNAMENT /AARIKANI@ULD

New Game Package

Table of Contents

New Game Package Contents ........ 0.0. ccc cece cece tenet e eens 2

Power and Monitor Requirements .......... 0... cece eee eee een eee 2

Recommended Tools and Supplies ........ 0.0.0 cece eee nec e eee eee 3

Game Operation... 0.0... cece eee een eee n eee e nee ene 5

Installation Procedures .... 00... cece cece cece cen e eee tence en nee eee 6

Control Diagrams ..... 6.6 cece een eee n etn ttn enn ee 12 Dip Switch Tables. 2.2.0.0... ccc cece eee e eee eee nen eee outside back cover Main Harness Connections........... 0. cece cece eee eee outside back cover Schematics 0.2.0... ccc e eee eee eect e eee nent ene teen insert

Page 4

TOURNAMENT

/MIRIKZAINIQULD) NEW GAME PACKAGE CONTENTS

Main Printed Circuit Board (PCB) PCB Cage (FCC Required) Set Legs, Bolts, & Spacers Connecting Wire Harness Control Assy. Player Button Assemblies Marquee Control Panel Overlay Plex Control Cover Set Side Graphics Set Play Instructions & Function Labels Service and Installation Manual

Note: Replacement accessories available through your exclusive Romstar distributor.

POWER REQUIREMENTS MONITOR REQUIREMENTS

+5 VDC +12 VDC 7 amp minimum lamp minimum Vertical Mount Raster Scan Negative Composite Sync

Page 5

Recommended Tools and Supplies

ROMSTAR new game package. Phillips and Slot Screwdrivers Socket Set Enthusiastic Attitude Wire Cutters and Strippers Pliers or Channel Locks Planning and Careful Thought Electric Drill 3/32" © 14" © 7/16" Dritl Bits 1/4" Plex Bit 1-3/16" Chassis or Sheet Metal Punch 1 114” Plex Hole Saw Glass of Water and a Snack Small File Razor Knife and Sharp Blades Straight Edge Patience Common Sense

Dip Switch Tables

Optimize Your Profits Painting Supplies (if you do your own painting) Paint Brush and Paint (don’t forget the primer} Paint Roller and Pan Sand Paper Putty Knife and Wood Putty A Good Night’ Sleep Staple Gun and Staples Soldering Iron and 60/40 Resin Core Soider Vacuum Cleaner Assorted Fastening Hardware Shrink Tubing: 3/32” © 1/8" © 3/16” Masking Tape 3 112" OR 4” Wire Ties Spray Window Cleaner and Rags (baby diapers work GREATI)

Thorough Research shows that two and a half minute games both satisfy players and also keep the quarters flowing. if games aren’t running about two and a half minutes long, then collections probably aren't at their peak. You'll want to tailor your game to your location. The trick is to adjust a few DIP switches. (See the chart in this book.) It’s easy!

Page 6

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 7

—Game Operation

CATCH CAPSULES AND REINFORCE THE VAUS!!

SLOWS DOWN THE ENERGY BALL.

G02) CATCH

CATCHES THE ENERGY BALL AND SHOOTS IT WHEN YOU WANT TO.

EXPAND

EXPANDS THE VAUS.

DISRUPT

SPLITS THE ENERGY BALL INTO THREE PARTICLES. LASER

ENABLES THE VAUS TO FIRE LASER BEAMS.

ALLOWS PLAYER TO MOVE TO NEXT PLAYFIELD.

PLAYER

GAINS AN ADDITIONAL

Page 8

Installation Procedures

Something To Think About Your final product will be anew game. You have made a wise decision to transform a game that has seen better days in the all important cash box into a new game. This is by far the most cost effective alternative to maximize the return of your initial investment. All you provide is the cabinet with a power supply and a monitor. Oh yes, you will need a touch of elbow grease. And that’s it! We provide the rest. The end result is... anew game ata very low cost. Fact: Spend alittle time on the cabinet’s appearance (i.e. marquee, control panel and cabinet graphics). With a little paint, some wood putty and new lights, you will raise the profits of any game. . .especially with the introduction of anew game package. The mew game [ook should always apply to the inside of your game as well as the outside. A few wire ties and shrink tubing on your harness; some fastening hardware on your subassemblies and a sweep with the ol’ vacuum cleaner will ensure that unnecessary g/itches do not occur. Remember: You are creating anew game . If you have any questions or just need some advice on any of yournew game transformations, don’t hesitate in giving a member of our technical staff a caii.

Let’s Get Our Hands Dirty

Preparing the Originai Game for the New Game Remove the following:

1,Main logic board(s}4.Monitor Bezel
2.Control pane!5.Marquee
3.Monitor plexiglass6.Graphics

| would recommend painting your cabinet to give it a fresh new look. (If it is geographically inconvenient to make use of our facilities, you may consider having an auto body shop take care of your painting needs.) If your cabinet has wood grain sides; remove old graphics and adhesive (adhesive may be removed with lacquer thinner. If you intend to use your original plexiglass, be sure it is in mint condition or it should be replaced. Thoroughly clean out your cabinet.

Page 9

Time To Install Your New Goodies

Before You Start. ..Remember DO NOT Do This Work With The Power On!

Logic P.C.B. Cage Mount the logic cage securely (away from power supply}. A Mark and drill pilot holes (3/32"). B Place the logic cage (bottom) over the holes and secure it with the supplied wood screws. C Install the PC.B. into the logic cage. Use feet and spacers supplied and adjust them so that the screws will go through the slots int he cage bottom.

Note: Leave the cage cover off until you have attached the entire wire harness and have tested the game for proper operation.

Wire Harness

Attach the wire harness connector to the main logic board. CAUTION: Sometimes the connector is not keyed and it is very easy to install it reversed on the logic board. Even if it is keyed, always triple check to be sure the wire inputs were connected correctly to the connector and the connector to the logic board.

Connecting the Wire Harness to the Existing Wires When you hook up the control panel, power supply, monitor or other subassemblies that remain in the game cabinet to your new wire harness, try and use their existing secondary connectors.

  • Cut the original wire approximately three inches from the original connector. Strip off about one half inch of insulation.
  • Solder the new wire designated for that position to the original wire you just stripped.
Warning: DO NOT JUST TIE THE WIRES TOGETHER. THIS CAN CAUSE NAGGING INTERMITTENT PROBLEMS THROUGH LOOSE CONNECTIONS OR OXIDATION OR BOTH. Always take the time to do it right.
  • Melt shrink tubing around all your in-line wire connections. Do not use electrical tape. Tape could unravel over a period of time due to the cabinet heat and cause you a great deal of trouble.
  • Use wire tie wraps, and secure the cable to the cabinet whenever it seems necessary. Remember this is anew game , not a sloppy conversion.

Power Wires

1, Connect the wires that are designated for your power supply. You will need a supply of +5V, +12V & ground. Your new game package may not require all of the voltages that were used in the original game. Tie off any unused wires.

  • You will notice that you probably have more than one wire for each voltage. It is a good idea to use all wires supplied (double up if it is necessary}. This will help to ensure that you don’t overload the edge connector pins and cause them to “burn”.
Page 10

Monitor Wires

You will be connecting the wires designated for the RED, GREEN & BLUE video guns along with the SYNC & GROUND wires.

NOTE. . .CONCERNING SYNC: Your mew game only calls for one sync wire connection, this is called composite syne (horizontal and vertical tied together}. This composite sync is also negative. Most monitors have supply positions for both negative and positive sync. You can check your monitor manual or call our technical department for assistance.

Speaker Wires Find the two wires that are designated for the speaker and hook ‘em on up.

Coin Door Wires

Connect the designated wires to the coin switches and meter.

  • Youcanconnect your door lamps to the unused —5V power supply. Some games have separate power outputs for the coin door lamps.
  • Be sure to clean and lubricate your old coin mechanisms. Keep the money coming in.

GUESS WHAT?

You are almost done with the electrical connections of your new game. All you have left is the control panel wiring. But we are going to hold off on that for right now. We have a few other things we need to do first. So why don’t you go ahead and get yourself a drink of water and stretch your legs. When you return, we can take a fresh look at your progress and then move forward.

Smoke Test

What Test?

Don't worry. All this means is that you are ready to apply power to the system for the first time and you pray that there will be no smoke from a simple oversight. You are just about ready to power up the logic board. But first we need to recheck your work.

  • Carefully inspect the game for loose power wires, exposed connections and extra fastening hardware.
  • Make sure the logic board, board cage, monitor and power supply are securely fastened in place.
  • Double check the connectors to be sure they are wired and connected properly.
  • Set the dip switches on the logic board to the factory recommendations. (Refer to page 5.) Also, be sure you set the dip switches for “DEMO WITH SOUND”. This will enable you to hear as well as see that your new PC.B. is functional.
Page 11

Time to Apply Power:

Look and smell for smoke. (TURN OFF IMMEDIATELY IF ANY IS NOTICED) Listen for game sounds. If after one minute you have not heard any sounds: A] Check for proper dip switch settings. B) Adjust volume control and check speaker connections. C} Check the +12V power supply to the logic board.

NOTE: If you do get sounds, but they are a little fuzzy, switch the wires around on the speaker. How is the monitor image? A) Is the picture in sync? If your picture has the top and bottom halves of the screen reversed and it will not stop roiling, change your sync polarity on the monitor. (Positive to negative} If your monitor does not have dual polarity positions for sync, then you will need to reverse the sync yourself by installing a simple one LC. circuit between the logic board and the monitor. (The following illustration shows a hookup for both composite and separate syncs.

HORIZONTAL SYNC INPUT FROM P.C.B. {OR COMPOSITE SYNC INPUT) HORIZONTAL SYNC OUTPUT TO MONITOR (OR COMPOSITE SYNC OUTPUT} VERTICAL SYNC INPUT FROM P.C.B 5 Vcc

VERTICAL SYNC OUTPUT TO MONITOR

B) Now how’s your picture? ® It it centered?

  • Is it too bright or dim? © Is it in focus? Check your monitor manual for these adjustments. If your screen looks ‘‘off”, then your new game transformation may have been in vain. So let's take the time to make the monitor look great. Cj Is the picture upside-down? Dip switch 7 should solve your problems.
Page 12

Control Panel Assembly

2. Remove the buttons, joysticks and wire harness and put them aside fro now. Do not remove the original panel overlay until the new holes have been drilled. Mark positions on the panel for the new holes. ROMSTAR supplies a clear 1/8” thick piece of plexiglass with every new game package to cover the control panel. We feel that your new game investment is well worth protecting. . .and the control panel is the first place to show wear and tear.

  • You will need to cut this piece to size. Use the control panel as a template.
  • Use a razor knife to score the plexiglass deeply. Then use a pair of pliers to break away the extra plexiglass. Now drill the holes in your panel that you have marked off for the buttons, Joystick and bolts. Hint: For best results, use a chassis or sheet metal punch for button holes. Drill the same holes on your plexiglass panel protector. Once again use your panel as a template. Hint: To avoid chipping while you are drilling the holes, place the plexiglass securely on a soft wood surface and use a plexiglass drill bit and hole cutter. The holes are now al! cut. Smooth them out on your panel and plexiglass with a fine toothed file. Remove the original graphics overlay from the panel. Clean up the panel and install your ROMSTAR graphics. Make It Easier: Peel the top half of the protective backing off of your graphics. Start from the center and smooth out your overlay. Make sure you have about an inch extra coming off the top. Wo bubbles please. Now peel off the bottom half and do the same as you did for the top. Adhere the instruction and function labels. Install the Plex Control Cover over your completed new game panel.
Note: Be sure to bolt the plexiglass securely to the panel. Mount the control and the buttons to the panel and wire them up. (Use the existing Panel wiring if possible)
NOTE : See page 12 for contro! mounting instruction

Marquee Installation

Using the original marquee as a template, Center your new game marquee graphics and score the new marquee deeply to fit the cabinet. Break off the excess with pliers. Be sure the light behind the marquee works. Everything should always work on anew game. Take your time ... Don’t forget this is going to be a new game.

Page 13

Side Graphic Installation

Be sure sides of game are clean and free of old adhesive, dust, etc. Mark position of decal with eraseable pen or pencil (centered on upper half of cabinet). Peel off top 1/4 of decal backing and apply to cabinet with a smoothing motion (use a soft rag). Continue peeling off backing and smoothing. Remove any small bubbles with a pin or razor blade (pop them!)

Finishing Touches

2. Check the game inside and out for any imperfections. Secure any loose wiring or fastening hardware. Make sure the coin door is tight and the coin mechs are well adjusted. A game is no good to anybody if you can't get a coin into it. Once again go over every step of this mew game transformation in your mind. Be sure everything is correct and to your liking. Power up the game. A. Check all the coin switches. (Does the coin meter work?) B. Play your new game . Are all the player controls working?

  • Are the game sounds present?
  • Is the volume level proper?
  • Are the dip switches set properly? Well, that’s about it. Good Luck.

n

Page 14

OPTO-COUPLER PCB 15002 1509 + fa] +5V-RED eA eA ec

eV, Cc a a Na Ne Ne

ok — ok ¢——1| RIGHT-GREEN/BLUE 150Q 1500 ew ews 14] LEFT-RED/YELLOW

  • [3] GND-BLACK

CONTROL PANEL LAYOUT

OPTO-COUPLER PCB (Connector Side)

  • —o —-— — —;

TO REMOVE KNOB & SHAFT ASSEMBLY - REMOVE NUT, SPROCKET, & E-CLIP FROM MAIN SHAFT.

NOTE : USE CONTROL ASSY. AS A TEMPLATE FOR MOUNTING HOLES ON CONTROL PANEL.
Page 15

WARRANTY, REPAIR AND RETURN POLICY THIS POLICY W/ILL REMAIN IN EFFECT FOR A PERIOD OF ONE YEAR FROM DATE OF PURCHSE FROM ROMSTAR. UPON EXPIRATION OF THIS ONE YEAR PERIOD, ROMSTAR WILL CONSIDER P.C.B. REPAIRS ON A BOARD—TO—BOARD BASIS, BUT IS NOT RESPONSIBLE FOR REPAIR OR REPLACEMENT.

  • *45 DAY FULL PARTS WARRANTY.
  • *60 DAY FULL ELECTRONICS WARRANTY (SEE RMA BELOW).
  • MINIMUM $40.00 SERVICE CHARGE FOR ALL NON-WARRANTY REPAIRS OR RETURNS.
  • ANY UNAUTHORIZED NON-FACTORY REPAIR OR ATTEMPTED REPAIR VOIDS WARRANTY.

(*ALL WARRANTY PERIODS BEGIN ON THE DATE OF PURCHASE FROM ROMSTAR)

RETURN MERCHANDISE AUTHORIZATION — (RMA)

  • ALL RETURNED MERCHANDISE MUST HAVE AN RMA NUMBER CLEARLY VISIBLE ON THE OUTSIDE OF THE PACKAGE.

2 ALL RMA NUMBERS MUST BE OBTAINED FROM ROMSTAR BY AN AUTHORIZED ROMSTAR DISTRIBUTOR. (PLEASE HAVE ROMSTAR SERIAL NUMBER AVAILABLE WHEN CALLING FOR AN RMA #).

  • ALL PC BOARDS RETURNED TO ROMSTAR WITHOUT AN RMA NUMBER WILL BE SUBJECT TO A MINIMUM CHARGE OF $40.00.
  • ROMSTAR WILL SHIP ADVANCE REPLACEMENT BOARDS TO DISTRIBUTORS OR AT DISTRIBUTORS REQUEST, DROP-SHIP BOARDS DIRECT TO THE OPERATOR.
  • ADVANCE REPLACEMENT BOARDS WILL BE BILLED TO THE DISTRIBUTOR UNTIL RECEIPT OF A RETURNED BOARD BY ROMSTAR AT WHICH TIME A CREDIT WILL BE ISSUED.

6 ALL REPAIRS AND/OR REPLACEMENTS WILL BE SHIPPED BY ROMSTAR WITHIN 24 HOURS OF RECEIPT OR REQUEST. (SUBJECT TO AVAILABILITY OF BOARDS).

  • FORANY ROMSTAR PRODUCT PURCHASED AFTER 3/1/86, A ROMSTAR WARRANTY CARD MUST BE ON FILE FOR EACH BOARD TO FACILITATE REPAIR & RETURN.

ANY QUESTIONS CONCERNING THESE POLICIES SHOULD BE DIRECTED TO DENNIS SABLE, TECHNICAL MANAGER OR SHAWN ZENKER, OPERATIONS OFFICER.

Page 16

WIRE COLOR ARKANOID WIRE HARNESS (G)

PARTS SIDE SOLDER SIDE COLOR

Black Ground Ground Red Video Red Video Ground Green Video Green Video Blue Gray Video Sync (Neg) N/A White Speaker (+) Speaker (-) Post Post N/A N/A Pink Coin Switch N/A ARKANOID WIRE HARNESS (H)

CONNECTION

Ground Ground Ground Ground Yellow Coin Meter wlolfaju}afo}ro|a N/A N/A N/A Tan Serv Switch Tilt Switch Brown 1P Select 2P Select N/A: N/A N/A N/A +5VDC

+12VDC 2P Left Post 1P Right 1P Left 2P Right N/A N/A N/A N/A Red 1P Fire N/A

SETTING OF DIP SWITCH

PLAY PRICING

  • 1 Coin 1 Play

Coin 2 Plays

2 Coins 1 Play

1 Coin 6 Plays N/A

NOTE: N/A

Double the red wire from pin 7

NUMBER OF PLAYER

BONUS POINTS 1ST A EVERY 20,000 pts. / 60,000 pts.

20,000 pts. only

GAME DIFFICULTY Rank A EASY

Rank B

TEST, MODE NORMAL GAME

TEST MODE

SCREEN INVERSION NORMAL

INVERSION

CONTINUED PLAY WITHOUT