Bowling Alley General Instructions (M051-00730-A006)
Bowling Alley (Midway, 1978) · Document · 4 pages · 1 sections · original scan
GENERAL INSTRUCTIONS FOR "BOWLING ALLEY"
INSTALLATION:
- Remove shipping cleats located on bottom of cabinet. .
- Install 4 provided leg levelers to bottom of cabinet and level cabinet.
- The power is controlled by a switch located on top of the cabinet. Plug into A.C. only, 115 volts, 60 cycles. In low line areas (105 volts or less), a boost in the output voltage of the transformer may be obtained by removing the wire from the 115 volt tap of the transformer and rewiring to the 105 volt position.
LINE VOLTAGE SAFETY SWITCH:
A line voltage safety switch has been provided for your protection. It is located on the left rear side of the cabinet in the upper back door area. When the back door is removed, it opens the circuit to the line voltaqe. To restore power (when servicing), pull switch fully out.
VOLTAGE CONTROL POTS:
Located on Power Supply Board (P.C. A080-90400-F000) and is preset at the factory. These pots should not be tampered with unless the Distributor Service Department is contacted.
VOLUME CONTROL POT:
Located on Game Logic Board (P.C. A084-90700-C730) controls the volume of all sounds and may be varied as desired by rotating pot control.
LAMP INTENSITY CONTROL POT:
Located on Game Logic Board (P.C. A084-90700-C730) control the intensity of all Flash Insert and Control Panel lamps and may be varied as desired by rotating pot control.
ADJUSTMENT SWITCHES:
Located on Game Logic Board (P.C. A084-90700-C730) and may be adjusted as indicated on separate instruction sheet in back box area.
Gord LAMP INTENSITY CONTROL (E ADJ. SW. GAME LOGIC VOLUME ba z CONTROL PC: 4084-80700-c730
PL 1
TO REMOVE CONTROL PANEL FOR SERVICE:
- Open Coin Box Door.
- Disconnect Control Panel jacks located to left of coin-box door opening.
- Unlatch clamp located on each side of cabinet.
- Remove Control Panel for service.
M051-00730-A006
; . ' ' ' ' 1 ! 92_COIN i ) COUNTER ' 1
' 13 ; + a + 12M rE
e SHON IDQLIQC OE HIELO
9009 £299
=
ogra
VIDEO
ok "9 n Sut en tin a ES moose a a eto ie or car ode 1, She rc avo 2
a
‘SONTRAST sores 4 aug goes epee, gs ars fa» on Boa Crests a ome ot
eye TH mow rote neeaTeD ro Am
osecft cai ‘Ac POWER ‘SOURCE ‘nPur POWER SUPPLY
a7 Aem REGULATOR
AsO” REF, 5.6K AMPL
wtp an TO PIN 7 (ca1nOOED L—___ ae vor To Ptah gpizonTaL 1. Salata Wy :
ceil om PULSE st a go 7035 "
aN), “&) svi a 0,
a it nf al
es
- uh =H
ay 42 FopUS aie p10 AGS
-oasoy Hosa
VIDEO 878 a cat FROM 5~ casy, {untold ann 2 | Lo ct na UE BRIGHTNESS
‘eR. SYNC. InTepeaTOR 4 R52 a3 ra vert. SYNC. AMPS
ourett
IE
M5000—155, M7000—155 — Diagram Schematic =f
BV oh
my 70 PNB HeaTER vOUTASE FOR V1
To MAIN BOARD
To.0201 COLLECTOR
Vem | SOLDER SDE sePcaone oN OVERLAY. BEPC.00817
tora
(ON CHASSIS)
svouT
+5 Volt Supply Circuit Card Detail — Solder View
SOLDER SIDE ~ BEPC-00418 OVERLAY — — BEPC.00419 *S1 MATES WITH P4/P5 ON MONITOR CHASSIS.
Audio Module Circuit Card Detail — Solder View