CATHODE RAY TOMES

Killer Instinct 2 (16-40064-101 Jan 1996)

Killer Instinct 2 (Rare / Nintendo (Midway license), 1996) · Manual · 51 pages · 26 sections · original scan

Page 1

JANUARY 1996 MIDWAY 16-40064-101

Ce

KILLER INSTINCT 2

DEDICATED GAME OPERATION MANUAL

Operation & Adjustments ° Testing & Problem Diagnosis

we Parts Information © Wiring Diagrams

Page 2

DECLARATION OF CONFORMITY

MIDWAY MANUFACTURING CO., INC.

3401 N. CALIFORNIA AVE. CHICAGO, IL 60618 US.A.

WE, HEREBY DECLARE UNDER SOLE RESPONSIBILITY THAT

THE MODEL: "KILLER INSTINCT 2" 40264, 40464, 41064, 41464, 42064 (VIDEO) TO WHICH THIS DECLARATION RELATES IS IN CONFORMITY WITH THE

FOLLOWING EUROPEAN PRODUCT SAFETY DIRECTIVES:

ELECTROMAGNETIC COMPATABILITY DIRECTIVE (89/336/EEC AND AMENDMENTS 91/C162/08, 92/31/EEC,93/68/EEC

AS IS VERIFIED BY COMPLIANCE WITH THE FOLLOWING STANDARDS:

ENS5014: 1993 EN61000-4-2: 1995 TEC 801-3: 1984 (EN61000-4-3) EN61000-4-4; 1995 EN61000-4-5: 1995

Date issued:

MANUFACTURE'S SIGNATURE

~ ee

DON HASSLER

V.P. MANUFACTURING

Page 3

HARD DRIVE HANDLING GUIDELINES

Hard drives are especially sensitive to rough handling and electrostatic discharge (ESD). To avoid these hazards, adhere to the following guidelines:

ELECTROSTATIC DISCHARGE (ESD) ¢ Keep the end of the drive cable in an anti-static bag until you are ready to install it in your system. ¢ Do not put any other objects inside the anti-static bag with the end of the drive cable.

HANDLING

  • Do not put anything on top of the drive - especially another drive. ¢ Do not drop a disk drive. Some drives can be damaged by being dropped from an inch above a hard surface.

e Be sure to handle the hard drive with care when setting it down. Do not set the drive on its edge.

INSTALLING

¢ When installing the drive, remove the cable from the anti-static bag. ¢ Turn off the power before connecting the drive to the system. ¢ Do not connect the drive to the CPU board, or disconnect the drive from the CPU board, while power is on.

e BE VERY CAREFUL TO ALIGN THE DRIVE CABLE CORRECTLY WITH THE CPU CONNECTOR. Installing a the hard drive cable incorrectly will ruin the drive!

STORING, PACKING, AND TRANSPORTING DRIVES ¢ Ifyou are using the single pack carton, do not pack more than one drive per carton. ¢ Pack the end of the drive cable in an anti-static bag. Then, put the hard drive in an approved shipping container. © Do not throw, drop, puncture, or walk on shipping boxes.

Note. You should use the same degree of care when handling a drive that may be defective that you use when handling a new, working drive.
Page 4

Information current at time of release.

Fill out and mail in game Registration card. Be sure to include the game serial number. For your records, write the game serial number in the manual.

MIDWAY Manufacturing Company reserves the rights to make modifications and improvements to its products. The specifications and parts identified in this manual are subject to change without notice.

Page 5

TABLE OF CONTENTS Section One - Operation and Troubleshooting Safety Notices. Set-up Procedure. 1-3 Inspection and Installatio: 1-3 Location Requirements. 1-3 Cabinet Assembly Diagrams. 1-4 Servicing....... Game Features. Starting-up. Player Controls..... Control Panel Diagram. 1-8 Game Operation... 1-9 Control Switche: Control Switch Location Diagram. Menu System Operatio: Operation... Main Menu. Diagnostic Test. Switch Test. DIP Switch Table and Test. CPU and Sound Test... Monitor Patterns and Bur Check Disk Test. Coin Bookkeeping Game Audits. Game Adjustments. Standard Pricing Table. Custom Pricing Tabl Utilities. Volume Adju: Troubleshooting. Section Two - Parts Information Cabinet - View 1 Cabinet - View 2 Cabinet Rear View. Cabinet Cut-Away Vie" Rear Door Parts & Coin Door Pal Contro| Panel & Housing Parts.

Other Parts Necessary to Section Three - Cabinet Wiring JAMMA Chart. Power Wiring. Cabinet Wiring Diagram. Killer Instinct 2™ © 1994, 1995 Nintendo/Rare ™Trademark of Nintendo Developed by Rare Manufactured and sold by MIDWAY Manufacturing Company under license, Nintendo® and Killer Instinct 2 ™ are trademarks of Nintendo Co., Ltd. The Rareware Logo™ is a trademark of Rare Ltd.

Page 6

NOTES

Page 7

NOTES

Page 8

SECTION

ONE

OPERATION

Page 9

SAFETY NOTICES The following safety instructions apply to all game operators and service personnel. Specific warnings and cautions will be found throughout this manual where they apply. We recommend that you read this page before preparing your game for play. ZN CAUTION HARD DRIVE. The end of the hard drive cable must be packed in an anti-static bag. The disk drive assembly must be packed in an approved shipping container (p/n 08-7981) in order to be sent in for repair or replacement.

TRANSPORTING GAME: This game contains fragile electronic devices. Do not move this game with power on. Transport this game securely. Avoid rough handling.

ISOLATION TRANSFORMER. This video game system does not utilize an isolation transformer. No isolation exists between the cabinet AC system and the external AC line.

AC POWER CONNECTION. Verify the slide switch on the power supply is set for 110VAC or 220VAC according to local line voltage. Verify that the fan and fluorescent lamp assembly are correct for local line voltage.

PROPERLY GROUND THE GAME. To avoid electrical shocks, do not plug in the game until it has been inspected and properly grounded. MIDWAY games should only be plugged into a grounded 3-wire outlet.

DISCONNECT POWER DURING REPAIRS. To avoid electrical shock, disconnect the game from the AC power source before removing or repairing any part of the game.

USE THE PROPER FUSE To avoid electrical shock, replacement fuse must match the original fuse in fuse type, voltage rating, and current rating.

HANDLE FLUORESCENT TUBE AND CRT WITH CARE. If you drop a fluorescent tube or CRT and it breaks, it will implode! Shattered glass can fly eight feet or more from the implosion.

ATTENTION PROPERLY ATTACH ALL CONNECTORS. Be sure that the connectors on each printed circuit board (PCB) are properly connected. If they do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty. All connectors are keyed to fit specific pins on each board. EPILEPSY WARNING A very small portion of the population has a condition which may cause them to experience epileptic seizures or have momentary loss of consciousness when viewing certain kinds of flashing lights or patterns that are present in our daily environment. These persons may experience seizures while watching some kinds of television pictures or playing certain video games. People who have not had any previous seizures may nonetheless have an undetected epileptic condition.

If you or anyone in your family has experienced symptoms linked to an epileptic condition (e.g. seizures or loss of awareness), immediately consult your physician before using any video games.

We recommend that parents observe their children while they play video games. If you or your child experience the following symptoms: dizziness, altered vision, eye or muscle twitching, involuntary movements, loss of awareness, disorientation, or convulsions. DISCONTINUE USE IMMEDIATELY and consult your physician.

1-2

Page 10

SETUP PROCEDURE

INSTALLATION & INSPECTION

Game Location Power Temperature Humidity

Requirements 120VAC @ 60Hz 3.0 Amps. 32°F to 100°F Not to exceed 220VAC @ 50Hz 2.0 Amps (O°C to 38°C) 95% relative

Cabinet Statistics | Shipping Dimensions Shipping Weight Width 27" - Depth 41" - Height 73" Approximately 385 Lbs

  • Remove all items from the shipping containers and set them aside. Inspect the exterior of the cabinet and the control panel for any damage.

2, The coin door keys are attached to one of the joysticks. Unlock and open the coin door and the cash box door. Remove the spare parts stored in the cash box and remove the rear door keys located on a key hook inside the coin door.

  • Remove the screws holding the rear door then unlock and remove the door. Inspect the cabinet interior for any signs of damage. Check all major assemblies to assure that they are mounted securely.
  • Refer to the Cabinet Wiring Diagram (Section 3), and check to see that all cable connectors are correctly secured. Do not force connectors. Watch for damaged connectors and avoid making reversed connections,
  • If a padlock is desired, turn the rear door hasp so that it protrudes from the hole in the back of the cabinet. Remove the two nuts inside the cabinet, at the top and middle of the rear door opening. Then slide the hasp off of the bolts. Turn the hasp, slide it back on the bolts and replace the nuts.
  • Next, locate the four leg levelers among the spare parts in the cash box. There are four threaded holes on the bottom of the cabinet; one in each corner. Place one leg leveler (with its hex nut) in each of the threaded holes. Lower each leg leveler until the cabinet is stable and ievel.

!! WARNING !! The cabinet is top heavy.

  • To attach the line cord, remove the four Phillips-head screws that mount the line cord cover plate to the rear of the cabinet. Match the prongs on the plug with the holes in the receptacle and push the line cord securely into place. Be sure the cord aligns with the indentation of the plate, (indentation should point toward the bottom of the cabinet). Remount the line cord cover plate.
  • Replace the rear door and screw (lock) it securely. NOTICE: Tamper proof screws and wrench are included in the spare parts bag. These screws are optional and may be used to secure the rear door panel. The T20 wrench is used for the installation of these screws. Close and lock the front coin and cash box doors.
  • Plug the game into a grounded (3-terminal) AC wall outlet. Switch ON the game, using the ON/OFF switch located on the upper left rear of the cabinet.

1-3

Page 11

CABINET ASSEMBLY Front View

FLUORESCENT BULB

MARQUEE

SPEAKER

25” MONITOR

JOYSTICK an

BUTTONS =

COIN DOOR CS @

CASH BOX DOOR > @

Page 12

CABINET ASSEMBLY Rear View

VENT COVER ON/OFF SWITCH

PROGRAMMED HARD DRIVE

  • 35] CPU/SOUND BOARD

FAN —|

oS SS SWITCHER POWER SUPPLY

REAR DOOR oO 8

LINE CORD

1-5

Page 13

SERVICING

¢@ Servicing the Control Panel Switch off power to the game and open the coin door. The control panel is held in place by two latches (located inside the cabinet) which provide constant pressure on the strikes. To release the latches, reach through the coin door opening toward the right and left sides of the cabinet. Do not reach straight back through the coin door or you could damage the monitor control board. Lift the latch handle and unhook the wire fasteners. Grip the joysticks and carefully tilt the control panel back on its hinge.

To return the control panel to its normal position, carefully lean it forward until it rests on the cabinet. Be careful not to let the contro! panel slam down onto the cabinet, or to pinch any wires. Always reclasp the latches.

@ Removal of the Viewing Glass Switch off power to the game and open the control panel. Remove the five hex-head screws and the black metal strip at the bottom of the viewing glass. Carefully, slide the glass from the side grooves and lift it clear of the cabinet.

@ Removal of the Monitor Bezel Switch off power to the game. Open the control panel and remove the viewing glass. Lift the bezel off of the monitor.

@ Monitor Replacement We recommend that you read the SAFETY NOTICES section thoroughly before beginning this procedure. Switch off power to the game. Remove the viewing glass and the monitor bezel. Completely disconnect the monitor from ail of its cabling. Remove the four flange nuts securing the monitor's mounting flanges to its mounting panel. Pull the monitor carefully from the cabinet.

AN CAUTION

The monitor does not require aii isoiaiion transformer. However, when servicing the monitor on a test bench, YOU MUST ISOLATE THE MONITOR FROM LINE VOLTAGE WITH AN ISOLATION TRANSFORMER. THE MONITOR IS HEAVY. BE SURE IT IS FIRMLY SUPPORTED IF IT MUST BE REMOVED FROM THE CABINET.

¢@ Hard Drive Replacement REMEMBER: HARD DRIVES ARE FRAGILE Use an anti-static bag and approved shipping container (p/n 08-7981) to return the hard drive to your distributor. Switch off power to the game and open the rear door. Unplug the ribbon cable from the CPU board Unscrew the four hex head screws from the spacers and set them aside. Remove the spacers from the enclosure and set them aside. Remove the hard drive and enclosure assembly, (see Hard Drive Handling Guidelines in the front of this manual). Place the spacers - one in each four corner holes in the new hard drive enclosure. Place the enclosure assembly, with the ribbon cable facing the front of the game, on the wood chassis. Line up the holes in the spacers with the screw holes in the wood and use the hex head screws to fasten the assembly in place. Carefully plug the ribbon cable into the CPU board.

Page 14

@ Removal of the Marquee Switch off power to the game. Remove the hex-head screws from the black marquee retaining strip located on top of the header. Remove the strip and carefully lift the marquee and the marquee glass from the top of the header. Store the marquee carefully to prevent damage.

¢@ Removal of the Fluorescent Light Assembly Switch off power to the game. Remove the marquee glass and the marquee. The fluorescent bulb is now accessible for replacement. Remove the plastic lamp locks. Grasp the bulb, give it a quarter turn, and remove it from its socket. Carefully, place a new bulb into the socket, and turn to reinstall.

To remove the entire light fixture, disconnect the fluorescent light assembly from its power cable. Remove the screws that hold the assembly to the cabinet then lift out the assembly.

!! WARNING !! If you drop a fluorescent tube and it breaks, it will implode! Use care in handling.

¢ Removal of the Speakers Switch off power to the game. Remove the marquee and the marquee glass. The speakers come out from the front of the cabinet. Be sure to disconnect the cabling and remove the nuts on the mounting screws before attempting to remove the speakers from the enclosure. Carefully, reinstall the seals upon completing any task in the speaker enclosure.

Volume Control, Begin Test Switch, and Service Credit Switch Open the coin door. The game's volume control and diagnostic push-button switches are located on a small bracket on the coin door. The volume is controlled by the two center buttons. Press the Volume Up or the Volume Down button until the desired sound level is reached. The Begin Test switch, on the right, activates the game's menu system. The Service Credit switch, on the left, allows credits to be allotted for service testing without affecting the game's bookkeeping total.

CONTROL SWITCH LOCATIONS SEEE—WOLUME CMe EON Sees Bown e is

Page 15

GAME FEATURES

STARTING UP Switch on power to the game. The game runs through a start-up routine.

Insert the desired amount of coins, bills or tokens. Select which player receives the credit by pressing the appropriate Start button.

NOTE When an error is detected during the Start-up tests, game start-up does not progress, and an error message appears on the screen.

PLAYER CONTROLS ¢ Start Button Each player has a Start button. The Start buttons allow one or two players to begin or continue play.

@ Joysticks Each player has a joystick which he uses to control an on-screen character. The player can make the on-screen character move, jump or duck.

@ High Attack An attack that originates above the waist, such as a punch.

« Low Attack An attack that originates below the waist, such as a kick.

« Quick A “quick" attack is a short range, short duration attack that inflicts little damage to an opponent.

« Medium A “medium" attack is a moderate range, moderate duration attack that inflicts some damage to an opponent.

«@ Fierce A "fierce" attack is a long range, long duration attack that inflicts much damage to an opponent.

NOTE Use joystick and button combinations to discover secret moves.

Stort Stort

High Attock High Attock mune Quick Medium Fierce dump Quick Medium Fierce

Move Move Move Move

Dueck Quick Medium Fierce ub Quick Medium Fierce Low Attack Low Attack

{ CONTROL PANEL

1-8

Page 16

GAME OPERATION The KILLER INSTINCT 2 game Control switches are located on a bracket, inside the coin door.

CONTROL SWITCHES

¢@ Slam Tilt Switch The Slam Tilt switch prevents pounding for free games.

@ Volume Down/Volume Up Buttons The Volume Down and Volume Up push-button switches increase or decrease the volume level of the music and speech. The volume level can be adjusted during the Attract Mode or during menu system operation. For greater profits, set your game's volume level at a nice loud setting.

¢ Begin Test Button The Begin Test push-button switch enters the game's menu system. Press the Begin Test switch to access any of the menu system functions.

« Service Credit Button The Service Credit push-button switch is a special feature switch that allots credit without affecting the game's bookkeeping total.

These buttons can be used instead of the contro! panel buttons when operating the Menu System. The Up and Down buttons move the cursor, and the Enter and Escape buttons open and close the menus.

NOTE The coin door must be open for the control switches to work.

BEGIN Test SERVICE VOLUME VOLUME creas OWN uP OC © O oO co) ENTER

CONTROL SWITCH LOCATIONS

Page 17

MENU SYSTEM OPERATION

OPERATION All game audits, adjustments and diagnostics are options of the Main Menu. Each option, in turn, has its own menu that lists several choices which you may act upon as desired.

Press the Begin Test switch on the coin door to open the Main Menu (shown below). Game adjustments, bookkeeping and diagnostics are all accessible from this menu.

Use any joystick to move the cursor up and down the menu screen. Notice that the options are highlighted in sequence. Press any action button (Quick. Medium, Fierce), on the control panel to open a highlighted option.

NOTE Only highlighted options can be opened.

To exit the Main Menu and return to the Attract Mode, use any joystick to select EXIT TO GAME OVER and press any action button.

Page 18

DIAGNOSTIC TESTS Use any joystick to select the Diagnostic Menu and any action button to open it. Then, use any joystick to move the cursor up and down the menu and any action button to open a highlighted option.

To exit the Diagnostic Menu, use any joystick to select RETURN TO MAIN MENU and press any action button.

Switch Test The Switch Test allows the operator to test the switches on the control panel and in the coin door.

Use any joystick to highlight the Switch Test and any action button to begin the test. During the Switch Test the top of the screen shows the control panel switches while the bottom of the screen shows the coin door switches. Press a control panel or coin door switch and the switch location on the screen lights. Release the switch and the screen returns to normal.

To exit the Switch Test, press both Start buttons together.

PRESS BOTH START BUTTONS TO EXIT O O Pt START 2. START 5000 ,OOO 2666 2 S60 OOO%0 O CONT COIN2 COINS. «COIN SERVICE = SLAM TEST LEFT RIGHT

=ly>
OO©
BILLYOL-Vvol+—D00R

SWITCH TEST SCREEN

Page 19

DIP Switch Test The DIP Switch Test allows the operator to check or change the position of the DIP Switches on the CPU.

Use any joystick to select the DIP Switch Test. Press any action button to access the DIP Switch Setting Tables. The screen displays the current settings. To change a setting, slide the switch to the desired position. Check the screen to verify the new setting. In some cases, setting a function to OFF actually enables the function. For example, setting Coinage to Off enables DIP Switch Coinage.

Press any button to return to the Diagnostic Menu.

DIP Switch 1 Setting Table sw.4 [sw.5 | SW.6 Blood Level High Blood Level Med. Blood Level Low Blood Level No Blood Attract Sounds Attract Sounds On No Attract Sounds Finishing Moves Finishing Moves No Finishing Moves Violence Warning Display Violence Warning No Violence Warning Not Used Jon [on [on On On

SW.6 | SW.7 | SW.8 DIP Switch 2 Setting Table sw.1 Coinage DIP Switch CMOS Coin Settings USA 1 Ger. 1 USA2 Ger. 2 USA3 Ger. 3

USA 4Ger. 4Fr. 4

E off

USAECA Ger.

USA9Ger.Fr. 11
USA 10N/UFr. 12
Free PlayFree PlayFree Play | On

Country USA Germany France Not Used 1 Counter Off 2 Counters On Game Mode Off" Test Mode On *Indicates factory setting.

Page 20

CPU Test The CPU Board Test allows the operator to check the RAMS and the ROMS. Select the CPU Board Test with any joystick. Press any action button to start the test. A “rug” pattern appears on the screen. When the “rug” pattern ends, either Test O.K. or Test Failed appears on the screen. The game returns to the Diagnostic Menu automatically.

Sound Test This test allows the operator to listen to some of the sounds this game is capable of producing.

Use any joystick to select the test, then press any action button to open the menu. The screen displays two test options. Use any joystick to select an option and any action button to begin the test.

GENERAL TEST analyzes the sound circuitry. The screen shows a list of error codes. A successful test causes a single "tone" to sound. Detection of a fault causes a series of tones or no tone at all to sound. Press any action button to return to the Sound Test Menu.

PLAY SOUNDS tests synthesized and digitized sounds from the CPU/Sound board. Advance to the next sound with any action button. Use any joystick to end the test.

Select RETURN TO MAIN MENU or BACK TO DIAGNOSTIC MENU and press any action button.

1-13

Page 21

Monitor Patterns The Monitor Patterns Test provides a menu for testing the monitor.

Select the test with any joystick. Press any action button to open the test menu. Once the menu is open, use any joystick to select an option, and any button to begin it. Press any action button again to return to the Monitor Patterns Menu.

The RED, GREEN and BLUE SCREEN tests fill the screen with either red, green or blue. Press any action button to return to the Monitor Patterns Menu.

The COLOR BARS test fills the screen with 15 shades of colors to help with red, green and blue level adjustments. Each color should appear sharp and clear. Press any action button to return to the Monitor Patterns Menu.

The CROSSHATCH PATTERNS test fills the screen with a grid and a series of dots. The grid and the dots should be clear. The dots should be round. Press any action button to return to the Monitor Patterns Menu.

If any of the tests show a need for adjustment, use the proper knobs on the Monitor Controls board.

To exit this test, use any joystick to select RETURN TO MAIN MENU or BACK TO DIAGNOSTIC MENU, then press any action button.

Page 22

Check Disk This test checks the hard disk drive.

Use either joystick to select the test, then press any button to activate it. Press any button to return to the Diagnostic Menu.

CHECK DISK SCREEN

Burn-in Test The Burn-in Test continually repeats the CPU Board Test. Use this test to find intermittent CPU Board problems. The Audit Table specifies the number of Burn-in cycles that have been successfully completed.

Use any joystick to select the test, then press any action button to activate it. When the Burn-in Test detects an error the test stops and an error message is displayed on the screen.

To exit this test, switch the game off, then on again.

Page 23

COIN BOOKKEEPING The Coin Bookkeeping Table records the coin box totals and the game play counters.

Use any joystick to select the Coin Bookkeeping Menu, then press any action button to open it.

To exit Coin Bookkeeping, use any joystick to select RETURN TO MAIN MENU and press any action button.

Page 24

GAME AUDITS Use any joystick to select the Game Audits Menu, then press any action button to open it. Page through the available audits by selecting NEXT AUDIT PAGE or LAST AUDIT PAGE. Select RETURN TO MAIN MENU and press any action button to exit Game Audits.

Game audits cannot be set. They can only be cleared.

Page 25

Game Audits Continued.

ie

1-18

Page 26

6L-b YT “panuyjuog s}ipny aue5

Page 27

Og-b oe ““panujjuog syipny awe

Page 28

Game Audits Continued...

a

EI t

1-21

Page 29

GAME ADJUSTMENTS The Game Adjustments allow the operator to customize the game.

Use any joystick to select the Game Adjustments Menu. Press any action button to open the menu.

The Game Adjustments Menu offers several options. Each option has several choices. Use any joystick to select an option, then press any action button to open the option. The next menu screen provides a setting value. Use any joystick to change the setting value and press any action button to lock it in.

To exit the Adjustments Menu, use any joystick to select RETURN TO MAIN MENU, and press any action button.

NOTE Adjustment values set by DIP SWITCH, override adjustment values set by the menu system.

Game Adjustments Standard Pricing Standard pricing allow the operator to choose any of the "standard" selections from the Standard Pricing Table. See page 1-24

Modify the setting value with either joystick. Press any button to lock in the new value and return to the Adjustments Menu.

Custom Pricing Custom pricing allows the operator to install pricing other than that of the Standard Pricing Table. Custom pricing also allows the operator to select the maximum amount of credits per game, the amount of credits required to start a game, and the amount of credits required to continue a game. To use Custom Pricing, the Coinage DIP Switch must be set to ON (CMOS). See page 1-25

Modify the setting value with either joystick. Press any button to lock in a new value and return to the Adjustment Menu.

1-22

Page 30

Game Adjustments Continued...

Free Play This option selects free play. The setting choices for this adjustment are: -No

  • Yes
  • Factory Setting: No

Computer Difficulty This option determines how tough the computer opponents are. The setting choices for this adjustment are:

  • (1) Extra Easy
  • (2) Easy
  • (3) Medium
  • (4) Hard
  • (5) Extra Hard
  • Factory Setting: Medium

Winning Streak This option determines the number of games that must be played before the high scores automatically reset to factory settings. The setting choices for this adjustment are:

  • No Reset
  • 5000 games
  • 10,000 games
  • 15,000 games
  • Factory Setting: No Reset

1-23

Page 31

STANDARD PRICING TABLE

Setting - Coin/Credit

25¢ (2 to Start, 2 to Continue) 1/250 (2 to Start, 1 to Continue) V25¢ (1 to Start, 1 to Continue) 1/50¢, 3/$1.00 (1 to Start, 1 to Continue) 150¢, 4/$1.00 (2 to Start, 1 to Continue) 1/50¢ (1 to Start, 1 to Continue) 1/50¢, 3/$1.00 (1 to Start, 1 to Continue) 1/50¢, 4/$1.00 (1 to Start, 1 to Continue) 1V25¢ (3 to Start, 2 to Continue) 1/25¢ (3 to Start, 3 to Continue) 125¢, 4/$1.00 art_2 to le German 1 1/1DM, 6/5DM German 2 4/1DM, 7/5DM German 3 4/1DM, 8/5DM German 4 1/1DM, 5/5DM German 5 1/10M, 6/50M German ECA __| 1/1DM, 2/2DM, 6/5DM France 1 2/5F, SOF France 2 2/5F, 4/10F France 3 1/SF, S/10F France 4 USF, 2/10F France 5 2/5F, S/10F, 11/2 x 10F France 6 2I5F, 4/10F, 9/2 x 10F France 7 4/5F, S/10F, 7/2 x 10F France & 1/5F, 2/10F, 5/2 x 10F France 9 1/3 x 1F, 2/5F France 10 12 x 1F, 3/5F France 11 13 x 1F, 2/5F, 5/2 x SF France 12 12 x 1F, S/SE, 7/2 x SF France ECA 1/3x 1F, 2/5F, 5/2 x SF 1/2 x25¢, 3/$1.00 T/F, 6/5F TIE, 7/5 A/F, B/SF Italy 1/500 lire UK1 1/20P, 3/50P UK2 2/20P, 5/50P UK ECA 1/20P, 3/50P 7/21 UK Elec w/CCU | 1/30P, 2/50P, 4/21

Spain 11/100 peseta, 6/500 peseta50C peseta
Spain 21/100 peseta, 5/500 peseta500 peseta
Australia 11/3 x 20¢, 2/$1.00$1.00
Australia 24/5 x 20¢, 1/$1.00$1.00
Japan 11/100 yen100 yen100 yen
Japan 22/100 yen100 yen100 yen
Austria +1/5 schilling, 2/10 schilling5 schilling10 schilling
Austria 21/2 x5 schilling, 3/2 x 10 schilling_5 schilling10 schillin,|
Belgium 11/20F20F20F
Belgium 23/20F20F20F
Belgium 32/20F20F20F
Belgium ECA1/20FSOF20FSF
Sweden1/3 x1 krona , 2/5 krona1 krona5 krona
Finland4/1 markkaA markkaAmarkka
1/2 x 1 krone, 3/5 x 1 krone1 krone1 krone
1/2 x1 krone, 3/5 krone, 7/2 x 5 krone1 krone5 krone,

1/25¢, 4/1 guilder 1 guilder 1/2 x 10 forint, 3/2 x 20 forint

New Zealand 11/3 x 20¢20¢20¢
New Zealand2_|1/2 x20¢20¢20¢
Netherlands4/1 HFI, 3/2.5 HFiTHEI2.5 HFI

1-24

Page 32

CUSTOM PRICING

Coins inserted accumulate units. This adjustment specifies the number of units given for each coin in the fourth chute (see "Units/Credit").

Coins inserted accumulate units. This adjustment specifies the number of units given for each bill validated (see "Units/Credits").

This is the number of coin units required to buy one credit.

There is one bonus credit awarded after this many coin units have accumulated.

This is the minimum number of units required before any credits are awarded.

Each player needs this many credits to begin a game.

Each player needs this many credits to continue a game.

This is the limit for the credit counter. Additional coins inserted will be lost (factory setting: 50).

1-25

Page 33

UTILITIES The Utilities Menu allows the operator to clear the game's bookkeeping memory.

Use any joystick to select the Utilities Menu, then press any action button. Use any joystick to select a utility. Press any action button to activate the selection.

Once the selection is made, a dialogue box appears, and the operator can choose to reset the utility.

For example:

CLEAR COIN COUNTERS? ARE YOU SURE?

YES NO

Use any joystick to choose a setting value. Press any action button to lock in the new setting value.

To exit the Utilities Menu, use any joystick to select RETURN TO MAIN MENU, then press any action button.

1-26

Page 34

VOLUME ADJUST The Volume Adjust feature allows the operator to determine the sound and music level of the game.

The volume level can be adjusted from either the Attract Mode or the Menu System. Press the Volume Up button to raise the volume level and the Volume Down button to lower the volume level. Any joystick can also be used to raise or lower the volume level. The current volume level is shown with a red bar.

Press any action button to return to the Main Menu.

VOLUME ADJUST PRESS ANY BUTTON TO EXIT

MAX.

MIN.

USE JOYSTICK OR VOLUME BUTTONS TO ADJUST VOLUME.

1-27

Page 35

TROUBLESHOOTING

PROBLEM 1)

2)

3)

4)

5)

6)

7)

8) No picture or distorted picture.

Turn game On and nothing happens.

No sound.

No general illumination.

Press Start button and nothing happens.

No credit given for number of coins inserted.

Too many credits for number of coins inserted.

Game stays in test mode. POSSIBLE SOLUTION 1)

2)

3)

4)

5)

7)

1-28 Check for faulty video board or monitor. Check for disconnecied video signal cable.

Check line fuse. Check for +5Vdc at pins C, D, 3 and 4 of the JAMMA connector.

Check the speaker and the speaker connection to pin L and 10 on the JAMMA connector. Check volume control setting. Check for +12Vdc at pins F and 6 on the JAMMA connector. Check for -5Vdc at pins E and 5 on the JAMMA connector.

Check -5V at pins E and 5 on JAMMA cable. Use pin “e” as ground reference.

Check for open wires between the button and the CPU board. Check for contamination on CPU board pins or the Start button switch blade contacts. Check for proper ground.

Check DIP switch coin settings. Check for contamination on the coin switch contacts. Check for an open wire between Coin Switch 1 and pin 16 on the JAMMA connector or Coin Switch 2 and pin T of the JAMMA connector.

Check the game pricing settings. Check for a short between pins T & 16 on the JAMMA connector.

Check that the switch #8 of DIP switch bank #2 is set to off.

Page 36

KILLER INSTINCT 2

SECTION

TWO

PARTS

Page 37

Fluorescent Lamp Assenbly A-20277 Fluorescent Bull 15W 24-8809 S Lamp tock : Nee

MS 8-32x3/8 PL-HWH 4008-91113-06 Nut 1/4-20 Flangrip Nut 1/4-20 Flangrip Bezel 4420-01141-00 4420-01141-00 03-8497

Monitor 5675-14660-01 Monitor Mounting Bracket CRT Glass dieieee 08-7456-10

2-2 CABINET FRONT - VIEW 1

Page 38

CABINET FRONT - VIEW 2

Marquee Retainer 03-8252-2 Screw H-F #8x11/16 PL-HWH 4608-01081-11 \ Channel Giass Edge 03-9373-1

Blank Marquee Glass 08-7456-4

Channel Glass Edge 03-9373. Speaker 8 ohm ‘5555-13961-00

Nut 6-32 KEPS 4406-01128-00 Cabinet Assembly 40064~C

Nut 8-32 KEPS On/OFF Switch 4408-01128-00

Screw SSS 6-32x1-1/2 4506-01106-24B

Speaker Grilte o1-11859

Screw #8x5/8 TRX-TR 4108-01193-10B

Bolt 8-32x1-1/4CB 4308-01123-20B

Coin Door-USA 09-50000-33

“e, ‘se

Control Panel A-20334 Blank Coin Door w/Lock (see detailed diagram) 09-41000 Not Shown: Glass Retainer Brkt, 01-13943 Leg Adjuster 08-7377 DVB InStallation Inst. 16-9637 Manual 16~-40064-101 Caster Wheel 20-9627 Screened Marquee 31-2380 Player Moves Card —31-2381-1 Helpful Hints Card 31-2381-2 MS #8-32x2 PPH Sems 4008-01105-32

2-3

Page 39

CABINET REAR VIEW

Handle Pull Vent 03-8326

Screw H-F #8x11/16 PL-HWH ~~ 4608-01081-11 Nut 1/4-20 Flangnip 4420-01141-00 <4

Bolt 1/4-20x1-1/4 CB 4320-01123-20B

Z Screw SMS #8x1-1/4 PL-HWH-A va 4108-0115-20B / Pad Lock Bracket 01-286 / Key Lock Bracket Ot-11287

Line Cord Cover 01-10714

Screw MS 8-32x1 P-RH SEMS Rear Door Assembly 4098-01003-16 4-20281 (see detailed diagram)

2-4

Page 40

CABINET CUT-AWAY VIEW

Hard Drive Assembly

CPU Board A-20333

Spacers

DETAIL

2-5

Page 41

REAR DOOR PARTS Complete Rear Door Assembly A-20281 *Door Lock Cam Upper Door Cam 01-8989

Lock Retainer 01-7264 Screw #8~32x11/16 PL-HWH 4608-01081-1

Nut 1/4-20 Flangrip 4420-01141-00

Lock Plate 01-11e85

x*Door Lock Cam

ot 1/4-20x1-1/4CB 4320-01123-208 Vent Hole Covet 03-7602

Primary 20-6542-1B Door ‘Bracke

Secondary 20-10187 01-11291

Bolt 1/4-20x1-1/4CB 4320-01123-20B

COIN DOOR PARTS

Chute Bracket 01-11334

Mars Chute 01-11379

Bolt 1/4—20x1-1/4 CB 4320-01123—208 4320-01123-20B

Coin Chute 01-12324

Nut 1/4-20 Flangrip Cover Plate 4420-01141-00 01-11275 Screw MS 4—40x3/8 P-FLH 4004—01041—06

Screw SMS #10x3/4 SL-HWH 4110-01088- 12

Meter Plate 91-11298-1

Coin Meter & Diode 5580-13476-00

Cash Tub 03-8863

Page 42

CONTROL PANEL & HOUSING PARTS Complete Control Panel & Housing Assembly A-20334

B07 ante Pushbutton

Hi-Fost #8 x 11/16" PL—-HWH 4608-01081-11 Blue. Pushbuttons 20-10209-3 8-way Blue Joystick 20-10178-3 White Pushbutton 20-10209-2 GROUNDING STUD FROM FAR LEFT SIDE OF HINGE,

Blue. Pushbuttons 20-10209-3 ~~

Security Loteh Bracket 01-11955 {located under panel) 8-32 KEPS NUT. (REF.) Control Panel Assembly A-20336

Wood Controt Pane! 04-10152

Sofety Chain FROM CABINET | P 20=9275-2 (Ree OND) crouno strae |

Centro! Panel Wood Housing 04-10151

pal Hi-Fost #8 x 11/16" PL—-HWH 4608-01081~-11

Wire Horness Clip, 1/2” 03-7655-8

Nut, 8-32 Keps 4408-01128-00

Toggle Loteh 20-9347 Hi-Fost #8 x 11/16" PL-HWH 4608~01081-11

Bolt, 8-32 x 1-1/4" Carriage = 4308-01123-208 Bolt, 1/4-20 x I-I/4 Flat Hd. Carriage 4320-01164-60

Nut, 1/4*-20 Flange Grip 4420-01141-00

Not Shown: Control Panel Plate A-19587 Control Penet Cable H~19597 Clear Overlay 03-9304 Screened Overlay 31-2379

2-7

Page 43

POWER SUPPLY 20-10167

REAR VIEW

*Note: Many computer grade power Connector Pin Designation supplies use yellow for +12V, blue for -5V,

Pin# — Function Wire Color

1,2,3+5VDCRedand white for -12V. This is acceptable as
4,5,6GroundBlacklong as the pinout is correct.
7-5VDC.Yellow*
8+12VDCOrange*

9 -12VDC_—Blue*

i

SIDE VIEW

© fill -~—O AE

FRONT VIEW

2-8

Page 44

KILLER INSTINCT 2 CPU FINAL ASSEMBLY A-20333

Designation Part Number Description

UtA-19802Programmed 20v8 PAL
U103A-19486,FPGA Assembly
U104A-19487FPGA Assembly
U92A-19488FPGA Assembly

Uu96 A-20351 FPGA Assembly

U98A-5343-40064-1EPROM Assembly
U10A-5343-40064-2EPROM Assembly
uitA-5343-40064-3EPROM Assembly
U12A-5343-40064-4EPROM Assembly
U13A-5343-40064-5EPROM Assembly
U33A-5343-40064-6EPROM Assembly
U34A-5343-40064-7EPROM Assembly
U35A-5343-40064-8EPROM Assembly
U36A-5343-40064-9EPROM Assembly

5761-12461-08 Header, 8-pin 5791-12461-10 Header, 10-pin 5791-12461-15 Header, 15-pin 5791-14457-00 Header, 44-pin

JAMMA CONNECTOR ae {e)

m ug2 U96

ug4

=

ie] ie] U1035

U33 U10 Ld LO U34 uit

U35 u12

U98 U36 u13

{e) {e)

2-9

Page 45

Other Parts Necessary to KILLER INSTINCT 2

Wood Chassis Panel 04-10157

Hard Drive Assembly A-20337 Spacers A-20356 Shipping Container 08-7981

Fan 20-9947

Fan Mounting Brackets A-19806

Fan Grille 03-9223

Fan Guard 20-9420

AC Distribution Assembly A-20278

AC Distribution Chassis 04-10103

Switcher Power Supply 20-10167

MS 4-40x3/8 P-FLH

MS 6-32x3/8 P-PH-S

Cables

Line Voltage Cable

Dixie-Narco Cable

Coin Door Cable

Control Panel Harness

Speaker Cable

Main Harness Cable

IDC Cable

Fan Cable 4004-01041-06

4006-01003-06

A-20331

H-17019

H118610

H-19597

H-19599

H-20338.1

H-20353

20-10235

2-10

Page 46

NOTES

2-11

Page 47

NOTES

2-12

Page 48

ER INSTINCT 2

SECTION THREE

WIRING DIAGRAMS

Page 49

JAMMA Chart

FUNCTIONWIRE COLORPINPIN | WIRE COLOR | FUNCTION
GroundBlackBlackGround
GroundBlack2
3Red+5VDC.

| 6 | +5VDC Red Red SVDC +5VDC Red Yellow ‘SVDC. -5VDC Yellow

+12VDCOrangeOrange+12VDC

7 Key Key

Coin Counter 2 | Brown-Red8BrownCoin Counter 1

9 N/IC N/C

10__|Red-Gra:Speaker +

Speaker- Brown-Gray

12edVideo Red

14 Video Ground Video Green Green

5 jue Te own Coin 4 1 Start la Video Sync White

ck ao a Slam Tilt Black-Green Coin 2 Black-Red 2 Start

2 Down Violet-Brown 2 Left jol 2 Right Violet-Orange 2 Quick/High Violet-Yellow 2 Medium/High 2 Fierce/High Violet-Blue

N/C27N/C

Black SOLDER SIDE COMPONENT SIDE i [fo Service Credits | White-Gray

1 Down 1 Left hite-Orange hite-Yellow

i 1 Fierce/High Not Used sls ro|r||={=fofo woo li 2/8 oO

S/=/= = =z

3-2

Page 50
Scan of page 50

This page is a drawing, shown as the original scan.

Page 51

ySIQ @avH OL wa00n 9 wen 9

88] 8b a aoans ance (82) 23 BEMAS (8 3 || Fo ¥ io §|| Sore WVXYSVIC ONIMIM LANISVS