CATHODE RAY TOMES

Atari TM-393 1st Printing Showcase 33in

Showcase 33 (Atari Games, 1993) · Technical Manual · 32 pages · 21 sections · original scan

Page 1

i a © M393 1st printing

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3

Service Manual

Universal cabinet for kits up to four players

Page 4

Copyright © 1993 by Atari Games Corporation. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976, This Act provides for substantial penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 per infringing transaction in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of corporations. Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game. Published by: Atari Games Corporation 675 Sycamore Drive Milpitas, CA 95035 Printed in the U.S.A. 12/93 Produced by the Atari Games Technical Publications Department. Writing and Design: Andrea Dencker.

Note re. Radio Frequency Interference

SOOMHHOH SEL EH ESTO D ED OLE M SE OOOCS This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which Showcase 33 Service Manual

are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an Atari game at your location, check the following: ¢ All ground wires in the game are properly connected as shown in the game wiring diagram.

  • The power cord is properly plugged into a grounded three-wire outlet. ¢ On games provided with an Electromagnetic Interference (EMI) ground plane and/or Filter Board, be sure that the game printed-circuit boards (PCBs) are properly installed on the EMI ground plane and that the Filter Board is securely installed with all screws in place and tightened. The person installing a game printed-circuit board in the Showcase 33 cabinet is responsible for assuring that such board does not cause radio interference. If the game board does cause radio interference, you must purchase a JAMMA Filter Board, available from your Atari Games distributor as Atari part no. A047292-01. Tf you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area,

Notice Re.

Notice Re Non-Atari Parts

Porecesscrerevessecsves

WARNING Use of non-Atari parts or modifications of any Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: + Substitute non-Atari parts, including cabinetry, in the game. © Modify or alter any circuits in the game by using kits or parts not supplied by Atari Games Corporation.

Page 5

Showcase 33 Service Manual

Safety Summary

Pereeccccseocveecocccs

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found in this manual whenever they

apply. :

WARNING Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected to ensure it is properly grounded. This game should only be plugged into a grounded three-wire outlet. If you have only a twowire outlet, we recommend you hire a licensed electrician to install a three-wire grounded outlet. If the control panel is not properly grounded, players may receive an electrical shock! After servicing any part on the control panel, check that the grounding wire is firmly secured to the inside of the control panel. After you have checked this, lock up the game. AC Power Connection. Before you plug in the game, be sure that the game's power supply can accept the AC line voltage in your location. The line voltage requirements are listed in the first chapter of this manual. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power before removing or repairing any part of the game. If you remove or repair the video display, be very careful to avoid electrical shock. High voltages continue to exist even after power is disconnected in the display circuitry and the cathode-ray tube (CRT). Do not touch the internal parts of the display with your hands or with metal objects! Always discharge the high voltage from the CRT before servicing it. Do this after you disconnect it from the power source. Fitst, attach one end of a large, well-insulated, 18-gauge jumper wire to ground, Then momentarily touch the free end of the grounded jumper wire to the CRT anode by sliding the wire under the anode cap. Wait two minutes and do this again. Use Only Atari Parts. To maintain the safety of your Atari game, use only Atari parts when you repair it. Using non-Atari parts or modifying the game circuitry may be dangerous, and could injure you and your players, Handle the CRT With Care. If you drop the CRT and it breaks, it may implode! Shattered glass from the implosion can fly six feet or more, Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating.
CAUTION Properly Attach All Connectors. Make sure that the connectors on each printed circuit board (PCB) are ptoperly plugged in. The connectors are keyed to fit only one way. If they do not slip on easily, do not force them. If you reverse a connector, it may damage your game and void your warranty. Ensure the Proper AC Line Frequency. Video games manufactured for operation on 60 Hz line power (used in the United States) must not be operated in countries with 50 Hz line power (used in Europe). If a 60 Hz machine operates on 50 Hz line power, the fluorescent line ballast transformer will overheat and cause a potential fire hazard. Check the product identification label on your machine for the line frequency required, ABOUT NOTES, CAUTIONS, AND WARNINGS In Atari publications, notes, cautions and warnings have the following meaning:
NOTE — A highlighted piece of information.
CAUTION — Equipment and/or parts can be damaged or destroyed if instructions are not followed, You will void the warranty on Atari printed-circuit boards, parts thereon, and video displays if equipment or parts are damaged or destroyed due to failure of following instructions.
WARNING — Players and/or technicians can be killed or injured if instructions are not followed.

iii

Page 6

Contents @oenerecccvere

1 Installation How to Use This Manual... Cabinet Equipment Requirements Tools Required...... Assembling the Control Panel Installing the Game PCB Installing the Bezel and Attraction Assembly. 2 Troubleshooting Introduction .........004 Troubleshooting Table 3 Parts INustrations See the List of Illustrations that follows. Showcase 33 Service Manual

Mlustrations

Figure 1-1 Cabinet Wiring Diagram.

Figure 3-1 Showcase 33 Cabinet Assembly............ 3-2 Figure 3-2. Showcase 33 Control Section Assembly... Figure 3-3 Coin Door Assembly Figure 3-4 Power Supply Assembly. Figure 3-5 | JAMMA Filter PCB Schematic Diagram* Figure 3-6 | JAMMA Filter PCB Assembly*

Tables weercccoce

Table 1-1 Specifications of Showcase 33 Cabinet... squietiensteersiness Le Table 1-2 Wire Connections in Control Panel Harness... 16

Table 2-1 Troubleshooting Table............00+108 2-2

“The JAMMA Filter PCB Assembly is not included as standard equipment in the Showcase 33 cabinet. However, you may need to purchase this filter board to eliminate radio inter- Jerence caused by your game board. The schematic and assembly diagrams of the filter board are provided bere for your conventence.

Page 7

CHAPTER

Installation

How To Use Tuis MANUAL

HE SHOWCASE 33”

cabinet accommodates

a game kit for up to

four players. This manual pro-

vides information for installing,

testing, and troubleshooting the

Showcase 33 cabinet. ¢ Chapter 1 describes how to install a

kit in your Showcase 33 cabi-

net. ¢ Chapter 2 contains a

troubleshooting table. ¢ Chap-

ter 3 contains the Showcase 33

cabinet parts and power sup-

ply illustrations.

Page 8

Installation

Cabinet Equipment Requirements

WARNING For safe use, you must install a game kit that has received Underwriters Laboratories listing.

Refer to Table 1-1 for the specifications of the Showcase 33 cabinet and what is required of your game kit printed-circuit board (PCB).

Equipme: Specification

Video Display 33-inch color standard-resolution RGB monitor Separate positive horizontal and vertical sync or negative composite sync Horizontal mounting Horizontal frequency: 15.750 KHz Vertical frequency: 60 Hz Video input: 1V to 3V peak-topeak positive polarity Is compatible with JAMMA standard (Japan Amusement Machinery Manufacturers Association) Cabinet Harness

One on each side of video display: 44-inch diameter, 8 Q, 10 W Provision for an additional 8-inch diameter, 2 Q, round speaker near bottom front of cabinet. Available from Atari Games Customer Service as part no. 148021-001.

+5 VDC or +12 VDC

50 Q; controls all speakers Speakers

Coin Counter

Volume Control

Power Cord NEMA 5-15P three-conductor with ground Power Supply +5 VDC + 0.25V @ 1.0 amps +12 VDC @ 1.0 amp -5 VDC @ 1.0 amp

Line Voltage 102 to 132 VAC, 60 Hz

Line Fuse Rating 250 V, 3 amps, slow-blow

Input Current 3amps Table 1-1 Specifications of Showcase 33 Cabinet

1-2 Showcase 33 Service Manual

WARNING To avoid electrical shock, unplug the cabinet while installing the kit. After installation, plug the game only into a grounded 3-wire outlet.

Turn off power to the game, and unplug the power cord.

Tools Required

© Drill with a 4-inch and %-inch drill bits

© Phillips screwdriver © Flat-blade screwdriver

  • Socket wrench set and ratchet
  • %rinch hex wrench
  • Wire cutters and strippers © Straight edge *° Squeegee ° X-ACTO™ knife
  • Carbon paper

° Saber saw

° File

° Bandsaw

  • Tape or glue

Assembling the Control Panel

Parts Needed for this Kit

To assemble the control panel, you need to decide on where to cut the control panel holes. Refer to the large template sheet that was provided with your Showcase 33 cabinet. That template shows suggested placements for controls in two-, three-, and four-player games. You will also need the following parts:

  • Clear Lexan cover for the control panel (supplied with the Showcase 33 cabinet)
  • Control panel decal supplied by the game kit manufacturer
  • Buttons, switches, and other controls, as supplied by game kit manufacturer
Page 9

Showcase 33 Service Manual

NOTE Spare blank (uncut) metal contro! panels and Lexan control panel covers are available from your distributor or Atari Games Customer Service, The metal control panel is Atari part no. 052821-01; the Lexan cover is part no. 052866-01.

Installing the Parts

1.

4, Using the large template provided, locate the recommended player positions that your game kit requires — two, three, or four. Mark the location of the primary control, for example, joystick, and then position the buttons as per the instructions provided in your game kit. On the metal contro} panel, drill/cut out the holes for mounting the controls of your game kit. Deburr the sharp edges with a file. Lay the metal control panel on top of the Lexan control panel cover, and outline all of the control and button holes. Drill a %-inch hole inside all of the large holes, Using a saber saw, cut out these holes. Drill any smaller holes required. Carefully deburr all the edges.

WARNING Wear safety glasses when drilling the plastic control panel cover. Use care to avoid shattering or chipping the plastic.

Apply the contro] panel decal provided in your game kit to the metal control panel. Then assemble the controls to the metal panel. Terminate the wires of the control panel adapter harness (one for each player) to match the controls being used. Make all of the proper connections. Mount the control panel assembly and the control panel cover to the cabinet using the hardware provided. For maintenance and servicing information on the controls, refer to the kit manufacturer's manual. Installation

Checking the JAMMA Connections Before plugging in the game PCB, turn on the power to the game, and check +5 Volts on pins 3, 4, C, and D of the JAMMA connector; +12 Volts on pins F and 6; and —5 Volts on pins E and 5. Check that the video display and the attraction lamp have power. Now turn off the power to the game.

Connecting the Control Panel Harness The Showcase 33 cabinet has an unterminated adapter harness for connecting any type of control installed in the control panel. This adapter harness disconnects from the main harness in the cabinet, to allow you to quickly remove the entire control panel if necessary. The Showcase 33 cabinet has a standard JAMMA harness that mates to a JAMMA-standard game printed-circuit board. Use the wiring diagram in Figure 1-1 to make the proper connections for all of your kit components. Table 1-2 shows all control panel harness connections and signal names.

Installing the Game PCB

  • After you have checked the power on the JAMMA connector (above), install the game board in the cabinet, Use the four screws and standoffs supplied with the game board to mount it onto the wood cabinet surface.
CAUTION The person installing a game printed-circuit board in the Showcase 33 cabinet is responsible for assuring that such board does not cause radio interference. If the game board does cause radio interference, you must purchase a JAMMA Filter Board, available from your Atari Games distributor as Atari part no. A047292-01. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.
  • If you need to install a JAMMA Filter PCB, plug it into the game board. Install the %-inch standoffs with adhesive to support the Filter PCB.
  • Connect the JAMMA harness connector to the Filter PCB.
Page 10

1-4 Figure 1-1 Cabinet Wiring Diagram POWER SUPPLY =| 5/8

gp 2i? Ga) ‘Moe0 oisPLAy 5/8 a) e

8] | «| 5] | >| >| 5] 3) 3/5

canner leé B(eeneee

PANEL,

—) F]

>|al 8] s|z|a : #15

a/x] 8/5] alls) alls

of flalaly

PLAYER 1

  • 5)5) 8) 5)8/ Bl) fs
  • 5) 5) 515) F1]5) |x

Eg seueTest com. coNTAL START tert purront urronz BuTToxa xo Installation Showcase 33 Service Manual

Page 11

Showcase 33 Service Manual

oj® vores:

(1 arencomecrs AAA” PUA OQ srencomecta com con courTen coven

wore erase | an 2500 « “bg NS “ re)

POWER EWIRY MODULE, Tr

Figure 1-1 Cabinet Wiring Diagram, Continued Installation

Page 12

Installation

PLYR 1

Pos. Color JAMMA Conn. _ Signal

1Ww7STRT1
2BN18UP1
3R19DN1
4OR20LF1
5YatRT1
6GN22FIRE1
7BU23ACTA1
8v24ACTB1
12BK28GND

PLYR 3

Pos.ColorJPL1 Conn.Signal
1Ww6STRT3
2BN7UP3
3R8DN3
4OR9LF3
5Y10RT3
6GN"1FIRES
7BU12ACTA3.
8Vv13ACTB3
12BK1GND

Showcase 33 Service Manual

PLYR 2

1WwWUSTRT2
2BNvUP2
3RWwDN2
4ORxLF2
5YYRT2
6GNZzFIRE2
7BUAAACTA2
8VvBBACTB2
12BKFFGND

PLYR 4

Pos.ColorJPL2 Conn.Signal
1Ww6STRT4
2BN7UP4
3R8DN4
4OR9LF4
5Y10RT4
6GNan)FIRE4
7BU12ACTA4
8v13ACTB4
12BK1GND

Table 1-2 Wire Connections in Control Panel Harness

4, Secure the JAMMA harness away from the PCB with cable ties.

  • Turn on the power to the game. Check that the game PCB functions. If a video picture is not present, see Chapter 2 of this manual.

Installing the Bezel and Attraction Assembly

Installing the Display Bezel

If your game kit includes a cardboard video display bezel, make sure it can fit the 33-inch video display used in the Showcase cabinet. Cut the hole and out-

1-6 side edges as required. Then find the game instructions label in the kit, and adhere that label to the control panel, under the Lexan cover.

Installing the Attraction Assembly

Find the game attraction film in your kit (the attraction shield of the Showcase 33 cabinet should be reused), Using the existing shield as a template, cut the film to size, if necessary. Install them in the cabinet attraction assembly.

1-6

Page 13

CHAPTER 2

Troubleshooting

INTRODUCTION

HIS CHAPTER contains a stall a kit in the cabinet, each time

troubleshooting table for you collect the money, or when

your Showcase 33” cabi- you suspect a failure. @ Table 2-1

net. Use the self-test procedure of (troubleshooting) on the next page your game printed-circuit board to can help you pinpoint problems in check the condition of the game your game. This table lists possible circuitry and controls. # You sources of problems in various should perform the self-test when you first in- _ parts of the game.

Page 14

‘Troubleshooting Showcase 33 Service Manual

Problem iggested Action

Coin Mechanism Problem 1. Check the wiring to the coin switch and counter.

  • Test the coin switch with the sound test screen in the self-test.

Game Play Problem 1. Check the harness and connectors.

  • Perform the self-test.
  • Check the voltage levels on the PCB.

Control Problems 1. Has the control been lubricated? If not, lubricate it. Refer to the game kit manual for instructions on how the lubricate the parts.

  • Check the harnesses and connectors.
  • If tested in the game self-test, check the controls’ functioning by using the self-test procedure,
  • If you took the control apart, have you reassembled it correctly?
  • Make sure all the parts on the controls are in good repair. Repair or replace parts.

Sound Problem 1. Is the speaker volume turned up? (Volume is usually adjusted on the game PCB.)

  • Check the voltage on the game PCB edge connector.
  • Check the wiring from the PCB to the speaker.
  • Check the voltage level to the PCB.
  • Replace the speaker.

Video Display Problem Screen is dark. 1. Is the game plugged in?

  • Is the game turned on?
  • Are the connections good?
  • Is the line fuse good?
  • Is the display brightness turned up?
  • Are the edge connectors on the game PCB arid JAMMA Filter PCB tightly connected?
  • Check ail of the items below. If you answer no to any question, you have a problem with the video display, not with the game circuitry. See your video display service manual. a. Do you have power to the video display? b. Are the video display’s filaments lit? c. Do you have high voltage to the video display?
  • Are the voltage levels to the video display PCB correct? (Power voltage is 100 VAC or 110 VAC, depending on the type of video display. Video signal voltage is 0.5 to 3.5 Volts.)
  • If the level is not correct, check the connectors and the harness.

Only a colored screen appears. You probably have a serious RAM problem. Display area wavers or is too small.

  • Do you have correct power voltage to the video display PCB?
  • Doyou have correct high voltage to the video display? Picture is wavy,
  • Is the monitor ground connected to the monitor?
  • Are the sync inputs connected properly?

Picture is upside down. Check the possible DIP switch settings on the game PCB. If such a setting exists, this toggle should be in the normal screen position for an upright game, not a cocktail game. Another possibility is if you serviced the display, you may have connected the wires incorrectly. Switch the horizontal or vertical yoke wires on the display.

Convergence, purity or color probiems. Use one of the screens in the game's self-test to adjust the video display. Use the adjustment procedures in the 33-Inch Hantarex Polo video display manual.

Picture is not centered. Use the centering procedures in the Hantarex video display manual.

Table 2-1 Troubleshooting Table

Page 15

CHAPTER 3

Parts Illustrations

HIS CHAPTER provides information you need to order replacement parts for your Showcase 33 cabinet. All

the common hardware parts included in the

cabinet, such as screws, nuts, washers, and so on, are included in these parts illustra-

tions. In addition, the JAMMA Filter PCB schematic diagram and assembly drawing is included in this chapter (although this board is not included as standard equipment in your Showcase 33 cabinet). ¢ When

you order parts, give the part number, part name, the number of this manual, and the

serial number of your cabinet. With this infor-

mation, we can fill your order rapidly and correctly. We hope this will create less downtime and more profit from your games. Atari Games Cus-

tomer Service phone numbers are listed on the inside front

cover of this manual.

Page 16

Parts Illustrations Showcase 33 Service Manual

Figure 3-1 Showcase 33 Cabinet Assembly A052875-01 B

Page 17

Showcase 33 Service Manual

‘SEE DETAIL G

SS nee

ETAL.

x (6

ax (42

3a

x(a

«wy

Figure 3-1 (ar) 12K

a1)07

  • ax

oo viEW 8

(12) Notes: ZA tocare roast are (ret on THE WOODEN NNER

A

A052875-01 B ‘SIDE PANEL PLEX SHIELD STOP AND THE INSIDE LIP OF ‘THE METAL PLEX RETAINER (ITEM 15) 2 SIDES. INSTALL BOLT (ITEM 52) AND WASHER (ITEM 94) ON THE MONITOR MOUNTING BRACKET (TEM 17) BEFORE INSTALLATION IN THE CABINET, PUT THE HANTAREX POLO DISPLAY SERVICE MANUAL ‘SUPPLIED WITH THE MONITOR IN THE COIN BOX. (FOR, (CUSTOMER SERVICE THE ATARI PINS 29-2033%6) LOCATE SERIAL NO. LABEL, (ITEM 11-07) ON THE INSIDE OF ‘THE MONITOR CHASSIS. LOCATE THE FRONT ACCESS LABEL ((TEM 11-06) INSIDE THE ‘COIN DOOR AREA OF THE CONTROL SECTION (A052874-01) ‘SOIT CANBE READ WHEN OPENING THE COIN DOOR.

ITEMS NOT SHOWN ON DRAWANG: Mem 27 WIRING DIAGRAM ITEM 32 ‘CORD, POWER SUPPLY ITEM 54 ‘OPERATORS MANUAL, ‘All vendor bt parts ara designated wth a °V" pret

Showcase 33 Cabinet Assembly, Continued

Page 18

Parts Illustrations Showcase 33 Service Manual

Figure 3-1 Cabinet Assembly A052875-01 B

Parts List

Item No.Part No.QuantityDescription
1A051839-011ASSEMBLY, ON/OFF SWITCH MODULE
3A052910-011ASSEMBLY, HARNESS, MAIN
4A052911-011ASSEMBLY, HARNESS, SECONDARY POWER
5A052913-012ASSEMBLY, HARNESS, SPEAKER
6A052914-011ASSEMBLY, HARNESS, PRIMARY POWER
7A052920-011ASSEMBLY, POWER SUPPLY
10038086-012LABEL, SHOCK WARNING
11038158-011LABELS, PRODUCT I.D.
12039450-011LABEL, FCC COMPLIANCE
13049514-021LABEL, UL, LISTING MARK
14051079-011LABEL, FUSE, 3A, SLOW BLOW
15052813-012RETAINER, PLEX
16052814-012GRILLE, SPEAKER
17052816-012BRACKETS, MONITOR MOUNTING
18052822-011GRILLE, SPEAKER
19052823-011COVER, POWER SUPPLY
20052824-011SHIELD, FRONT
21052828-011BEZEL, MASKING
22052829-011COVER, MONITOR
23052840-011DOOR
24052847-011SHELF, ELECTRONICS
25052879-011LABEL, POWER SUPPLY RATING
26052880-011LABEL, INSTALLATION WARNING
27052909-01REFWIRING DIAGRAM
28052870-011CABINET, WOOD
30139035-0011VIDEO DISPLAY, COLOR RASTER (HANTAREX POLO 33”)
31148007-1042SPEAKER, 4 1/2 DIA., 8 OHM, 10W, 10 OZ., SHLDED
32150041-0011CORD, POWER SUPPLY
33175002-0074WASHER, FLAT, .281 X 1.25, STL/ZINC
34175015-012512WASHER, LOCK, EXT., #1/4, ZINC
35176003-1082SCREW, TAPPING, #4 X 1/2” LG, X-REC
36176015-11024SCREW, TAPPING, #10 X 5/8 LG, X-REC
37176019-21216SCREW, LPW, SQ DR, #8 X 3/4” LG, BLK
38176020-2205SCREW, LPW, X-REC, #8 X 1 1/4 LG, BLK
39176037-40166SCREW, BUTTON HD, CAP, #10-24 X 1.0, HEX, TAMPER PROOF, BLK
40177000-1381NUT, HEX, #8-32, STL/ZINC
41177026-00444NUT, WASHER ASSY, #1/4-20
42178018-0016STAPLE, 1/2” CROWN X 5/8” LG.
43178205-001omEXTRUSION, 1/16”, PANEL EDGE, BLK, PVC/ALUM.
44178263-1202120”TAPE, VINYL FOAM, 3/4” X 1/8” THK, BLK
45178265-0014STANDOFF, L-STYLE, NYLON
46178282-0034‘WASHER, FASTENER CAP, .062
47178282-0064CAP, FASTENER, 0.70, MATTE, WHITE

3-4

Page 19

Showcase 33 Service Manual Parts Illustrations

Figure 3-1 Cabinet Assembly A052875-01 B

Parts List, Continued

Item No.Part No.QuantityDescription
5072-551612BOLT, HEX HD, #1/4-20 X 1.0” LG (PULL THD)
5172-6608S4SCREW, PAN HD, TYPE AB, #6 X 1/2” LG
54TM-3931MANUAL, OPERATORS (SHOWCASE 33)
v2049517-014PLATE, LEVELER
V4178387-00120”CHANNEL, CORNER, 1/2” WHITE, STYRENE (20 INCHES REQD)
V10178023-0034CASTER, SWIVEL, 4” HARD RUBBER
Vil178034-102433’T-MOLDING, MOUNTAIN GRAY, 3/4” (3 FEET REQ’D)
vi2178195-0044GLIDE, ADJUSTABLE, #1/2-13 X 2.0”
vi13178197-0011LOCK & KEY ASSY
v14178198-0021CAM, OFFSET, 1 1/2” X 3/32”
VIS178276-0021ANCHOR, WASHER (WOOD)
vi7178282-0036WASHER, FASTENER, CAP, .062
vis178282-0056CAP, FASTENER 0.70, MATTE, GRAY
NOTE The person installing a game printed-circuit board in the Showcase 33 cabinet is responsible for assuring that such board does not cause radio interference. If the game board does cause radio interference, you must purchase a JAMMA Filter Board, available from your Atari Games distributor as Atari part no. A047292-01. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.
Page 20

Parts Illustrations

3-6 13K Showcase 33 Service Manual

A-—

NoTEs:

  • THE FOLLOWING ITEMS ARE TO BE PLACED INSIDE THE PLASTIC BAG (ITEM 25) AND SHIPPED INTHE COIN BOX assy (ITEM 1): ary
ITEMSASSY, GROUND JUMPER1
ITeM6ASSY, HARNESS CONTROL,4
iTeMa1BOLT, HEXHD, #1/2-20 x 2"8
TEM 28CAP, FASTENER, GRAY8
TEM 20WASHER, FLAT #1/46
ITEM 22WASHER, LOCK #1/46
ITEM 26DRIVER, HEX KEY1

Figure 3-2 Showcase 33 Controi Section Assembly A052874-01 A

Page 21

Showcase 33 Service Manual Parts Ilustrations

23 ) 2x

2x (29

SECTION A-A

Figure 3-2 Showcase 33 Control Section Assembly, Continued A052874-01 A

Page 22

Parts Illustrations Showcase 33 Service Manual

Figure 3-2 Showcase 33 Control Section Assembly A052874-01 C

Parts List

Item No.Part No.QuantityDescription
2A044072-011ASSEMBLY, COIN COUNTER
3A047222-011ASSEMBLY, BRACKET COMPONENT
4A052912-011ASSEMBLY, HARNESS, POD
5A052915-011ASSEMBLY, GROUND JUMPER CONTROL
6A052916-014ASSEMBLY, HARNESS, CONTROL
7030247-011HANDLE, CASH BOX II
8035941-011COIN BOX, MOLDED (400)
9044448-011BRACKET, COIN BOX
10052802-012PANEL, FILLER
11052821-011PANEL, CONTROL (BLANK)
12052866-011COVER, CONTROL PANEL (BLANK LEXAN)
13052868-011CONTROL POD, WOOD
14052869-011CONTROL SECTION, WOOD
15049300-011LID, CASH BOX (4-ENTRY)
VW171101-0031COIN DOOR, 4 ENTRY, $.25 USA, 2 BLANK, WITH BRKTS
18172025-44248SCREW, PAN HD, #1/4-20 X 1.50 LG, X-REC, ZINC
19175002-0074WASHER, FLAT, .281 X 1.25, STL/ZINC
20175014-10506WASHER, FLAT, #1/4, ZINC
21175014-304013,WASHER, FLAT, .219 X .500 X .049, STEEL, BLK OXIDE
22175017-202510WASHER, SPLIT LOCK, #1/4, STL/ZINC
23176015-1109SCREW, TAPPING, PAN, #10 X 5/8 LG, X-REC
24176037-401613SCREW, BUTTON HD, CAP, #10-24 X 1.0, HEX, TAMPER PROOF, BLK
25178041-0051BAG, P.E., 7” X 10”, 4 MIL, CLEAR
26178126-0021DRIVER, HEX KEY, 5/32”, TAMPER PROOF
27178282-0038‘WASHER, FASTENER, CAP
28178282-0058CAP, FASTENER, 0.70, MATTE, GRAY
3172-553210BOLT, HEX HD, #1/4-20 X 2.0 LG (FULL THD)
V1043939-014PLATE, LEG LEVELER
v3052812-014BRACKET, MOUNTING
V16178255-0044GLIDE, ADJUSTABLE, #3/8-16 X 1.50”

3-8

Page 23

Showcase 33 Service Manual Parts [lustrations

NOTES

Page 24

Snap-on Sleeve

Hold-Down Bracket Parts Illustrations

99-15025 Left Coin Inlet

99-15113, Key Hook

99-15056 Screw for Bezel

99-15096 Sw. Adjuster

99-15056 Screw

99-15131 Elastic Locknut 99-15132

99-15130 Snap-on Clip

99-15133

Coin Ret. Plate

99-15128 Nut/Washer for MIS Mounting Screw

99-15129 Mounting Stud (2 places)

99-15051 Lamp Holder:

99-15029| Bracket

99-15042/ ‘Switch Coin Mechanism Showcase 33 Service Manual

99-15104 Base Plate ‘W/Pivot & Stud

99-15100 _ temp

99-15026 Right Coin Inlet

99-15056 ‘Screw for Bezel

9915028 ‘Coin Return Box

99-15056 ‘Screw for Bezel

99-15134 4-40-1" Pan-Head Screw

99-15126 MIS Flat-Head Mounting Screw

99-15085 Coin Door Hamess

Figure 3-3 Coin Door Assembly (Coin Mechanism Details) 171101-003

Page 25

Showcase 33 Service Manual Parts Illustrations

99-15136 Reject Button Without Slot (Used in the right two coin positions)

99-15038 Bezel for Button

99-1501 thru 99-16088 99-15012 Lock Assy Reject Button (Used in the left two coin positions) , a 99-1506 Cover a 99-15125 ~~ Frame Hinge Screw L co

99-15052 Spring for Button

99-15039 Bezel for Cover

99-15088 Clamp

99-15135 Frame Clamp Screw

NOTE

The coin box is not part of this assembly. It is shown in the Control Section Assembly drawing (Figure 3-2 of this manual). Also, the Showcase 33 cabinet provides for two players with provision for up to four players. To convert to a four-coin-mech game, add two coin mechanisms (Atari part no. 99-15086) and two reject buttons (99-15001 for U.S. quarters). The reject buttons replace the buttons without slots (99-15136).

Figure 3-3 Coin Door Assembly (Frame & Door) 171101-003

3-11

Page 26

Parts Illustrations

3-12 anes

anes

o| 00 8 A @| ° °°

fo} oO fo}

w 7 Chor OS eno) ctet © ial °

°

FLAT SIDE OF SEMHNS. QUICK-CONNECT FLAT SIDE OF FULLY INS. QUICK-CONNECT

GENERAL REFERENCE DETAIL SHOWING

PROPER PLUGGING OF TERMINAL BLOCK

Figure 3-4 Power Suppiy Assembly A052920-01 A Showcase 33 Service Manual

NoTES ZA\ armion Luas 0 swinchen As FoLLows: Rosey on Vv Yo atv BN Dc COM (GND) BN DC COM (GND)

Page 27

Showcase 33 Service Manual Parts Illustrations

Figure 3-4 Power Supply Assembly A052920-01 A

Parts List

Item No.Part No.QuantityDescription
1046924-011CHASSIS, POWER SUPPLY BASE
2149014-0011POWER SUPPLY, SWITCHING, 5V @ 7A, 12V @ 1A, -5V @ 1A
3179231-0021TERMINAL BLOCK, 2 POS, FLAT-45-90
4179225-2201.1FUSE BLOCK, 1 POS
5146008-30221FUSE, 3 AMP, SLOW BLOW, 250V
6A049295-011ASSY, JUMPER (BK, 6”)
7A049295-021ASSY, JUMPER (W, 6”)
8A049293-011ASSY, JUMPER, 5V (R/W, 10”)
9A052911-011ASSY, HARNESS, SECONDARY POWER
10037640-011LABEL, POWER SUPPLY (WARNING)
u043908-011LABEL, POWER SUPPLY (FUSE)
12J2-HA4606S = 3SCREW, THD FORM, X-REC, #6-32 X 3/8
1372-HA4806S2SCREW, THD FORM, X-REC, #8-32 X 3/8
14177026-0038«1NUT/WASHER ASSY, #8-32

3-13

Page 28

Parts Illustrations

FROM GAME BOARD

st 1 O——* OND 2 O-—* CND 3 O——a Jus. 4 Oa sts 5 O——a Ji-by 6 O—a netzy 70> KEY 8 O——« JLENTR2. 9 Os JuLocKe 19 O—s J15PxR1a1 0 JinupenD 12 O——* J1GREEN 13 o-——* JISYNC. 14 O—= JiseRV 15 O——* JAVTLT 16 O-—# JARCOIN 17 Ow SAS TART? 18 O——« yaup2n,

  • O—# JLDOHNZA 20 O—s JLLEF TAA 21 O—* JaRT2A 22 O—# JAF TREZ 23 0s J1uP20 24 0 —* JiponNes 25 O——* LEN T25 26 0 JART2B 27 O-—# GND 28 0 —s CKD RO cNnD 5 O—scNp COs Jey DO—"Jiesy —£O—« 1-5 F Oe Jiea2y Ho- Ker J Oe JienTet K O—« J1LockKt £ O—* JispRRi+ 4 Oa sabe NO-—=s JiRED Pos JioLUE, R O-—# JIVIDCND § O——# JISLFTST T O——# ALCON v Os JiSTeRTA v o-—« suP1a H O——« J1DOHNLA X Os JLLEFTIA Y Oe si8TiA 1 Os JUFIREL an o—* J1UPLB 85 O-—* JiDeww2B CC O——# JILEFTIB DD O——« JiRTIB EE O——eGno FF O—-"CND

3-14 cae Ji-5y a = 50 = 2200°F coy saetgye——] re sete 2200°F

JACNTRE — TT JeNTRE *200FF cen JALOCK2 e———_] -----_- ——— JLOCK2, eens

JASPRAL- #0 Pn ISPKR1- = 2200PF cay + RUD Te 22000F

SAGREEN 7 270PF 633 sagen @ ——[ pa snc

JASERD its rl JSERV

inane ————# JRCOTN

ene FS

co JALEFTen 9p LEFT Ts 2200°F cua sarTen eee eeeeetat ated uRT2A 2200RF

cue, JAP IRER #— np nn JPIRER, 2200°F x3 sayp28 x——| ea supe =o ye e200re

‘JADON2B SS JPORNZE

cle =

enor IL Showcase 33 Service Manual

sissy -— oa J05U 2200PF cp J1-5ye—_| {-——_~p-»—+ Jo5u =e ezoorr

seve Zz 2200PF cy giea2ya———| = sey 2200PF a -5y

JAcNTRL ep SENTRA 2200°F cg satorkt x -——rpe—e srocnt = Tr 2200eF JASPKRL + #— ia JISPKRA+ 2200PF a a sips LAUDS =

ca JLRED # rena RED =r 270PF C19 JALue =} re J

  • = 27 0PF L ‘JAVIDGND te SUTDEND To 2200PF cap sastrtst «|p cet i JALCOTN — -# JLCOIN = 2200°F cy. aastaRis @—— |p —e stent

Jiu. easier + pia JALDOWNLA —_ JDOWNIA

a

Z

ca = JADOWNL #9 —* JDOWNLG chs aeoapr

Figure 3-5 JAMMA Filter PCB Schematic Diagram A047292-01 B

Page 29

Showcase 33 Service Manual

TO GAME HARNESS

JANG. GND #——o JAHHA-A GND #——O JANHA-8. J+5Y ——0 JPHMA-C J95V &—O JAMMA-~D J-5U m= -0 JAMHA-E, Je420 50 Jasnin-F -O seta JENTR2 a——O JAMHA-J SLOCK? "&——O JAMMFA-K JSPKRL- s—O JAMHARL JAUDGND ®@——O JAMMEI-H ‘SOREN ®———o JMMA-N JSYNC #——O JaMHA-P JSERV *—O JAMHA-R STILT # =O JAMMA-S. JRCOIN &—O JAMHE-T JSTARTZ ®™——O JAHMA-U JuP2A =—O JAMMA-V JDOHNZA %———O JAMH-H SLEFTZA =—O JAMHA-X JRT2A &——O JAMHA-Y JFIRE2 *—0O JAMHa-z JUP2B =—-—-0 JAMHA-HAL JOOHNZB <——O JAMHA-BB JLEFT2ZB »——-0 JAMMA-CE JRTZB&——O JAMMA-DD GND *—o JANHA-EE. ND =o JAMHA-FF

Jet GND B——0 JAMHA 1. GND #—0 JAMHA-2 3250 8——0 Jenna-3 J95V ——O IRIE 4-50 8——O JAMHA-5. Je12) ¥——O JAMA 6 -O JAnKA-7 JENTRA #—O JAMMA-B JLOCK1 *—O JAMMA-9 JSPRRL+ =O JAMHA~10 JAUD+ ®——O JAKHA-11. JRED "——O JAMHA~12 JOLUE @——O JPHHA-13 JVIDCND *——0 JAMMAR14 JSLFTST @——O JAMMA-15 JLEQIN #——O JOMHA-16 JSTART1 *—O JAMMA-17 JUPLA ®—O JAMMA-18 JDOKNIA ®—O JAMMA~19 JLEFTIA sO JamHn-20 JRTIA #——O JnnIMA-24 JEIREL = JAMMA-22, JUPLB &——O JAMMA-23 JDOWNID #—O JAMHA-24 JLEFTID =O JAMHA-25 JRTAB &—O JnnHA-26 GND ™——O Jamna-27 GND =——o Janna-28 ceND) ceND) ©8509 c+5u) et ¢-502 © aa HIG HOLE

KEY we CECNTRR L-@ CC-LOCKR MEG HOLE

CSPERI-) 2 cup cNoD t—@ crue MTG HOLE SYNC? C SERVICED = im1LT) CCOINR > CSTARTRD cupRad cDOKWRAD CLEFTRAD CRICHTRAD CRBUT TONS > CREUTTON2 > CRBUTTONI CLEFTRBD CRICHTRED CeND) ceND3

cen? END? c+sv> focrey c-50) ferecy Ker CoCNTRL CO-LOCKL cspKRie) CAUD+ CRED? BLUE? VID CHD CSELFTEST> CCOTNLD CSTARTLD cuPLA> CDOKNLAD CLEFTLAD CRIGHTLAD CLBUTTONS > CLBUTTONZ > CLEUTTON3 > CLEFTLB> CRICHTLED CRN CcND >

Figure 3-5 JAMMA Filter PCB Schematic Diagram, Continued A047292-01 B Parts Illustrations

3-15

Page 30

Parts Illustrations Showcase 33 Service Manual

Figure 3-6 JAMMA Filter PCB Assembly A047292-01 B

JAMMA Filter PCB Assembly Parts List

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No.
c1-82200 pF, SOV, 3-Pin EMI Filter Cap.140006-222C32, C33270 pF, 50V, 3-Pin EMI Filter Cap.140006-271
C9, C10270 pF, SOV, 3-Pin EMI Filter Cap.140006-27134-462200 pF, SOV, 3-Pin EMI Filter Cap.140006-222
C11-312200 pF, SOV, 3-Pin EMI Filter Cap.140006-222jiConnector, 56 Ckt., .156 Ctr, RT179240-056

3-16

Page 31

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to ensure your

Corporation cannot be responsible for the quality, s of any non-Atari

oF foci clean alte heme Sori

Page 32

I

ATARI

GAMES

_ Atari Games Corporation 675 Sycamore Drive Milpitas, CA 95035 U.S.A.