CATHODE RAY TOMES

Final Furlong 2 Conversion

Final Furlong 2 (World, FFS2 Ver. A) (Namco, 1998) · Document · 19 pages · 5 sections · original scan

Page 1

namnco

FINAL FURLONG 2

CONVERSION INSTRUCTIONS

Page 2

It is most important that the game is tested and any problems rectified before any conversion work is started.

Please make a note of all setting values so that the new Game PCB can be set accordingly.

Warning: Ensure that the game is switched off and disconnected from the mains supply before any conversion work is started.
Caution: Ensure adequate space is available to able to remove the header safely.
Note: Take care when removing items not to lose any screws and washers as they may be required for reassembly.

Tools Required:-

No1 Pozi Driver

No2 Pozi Driver

Security Wrench for MS

Spanner for M10 Spanner for M20

Security Torx Wrench for M5 (Supplied in kit)

Page 3

PRELIMINARY

Removing the Ride Assembly

  • Raise the twelve adjustable feet, (4 on the monitor cabinet and 4 on each ride base assy), (Slacken the lock nuts with a spanner first.)

Monitor Cabinet Ride Base Assy 9}

Lock Nut Adjustable Feet

  • Remove 8off security screws (M5x12) and remove both Base Front Cover Plates.

Base Front Cover Plates

  • Remove 4off hex head screws (M10x35), with flat and spring washers, retaining the ride base to the monitor cabinet.

Monitor Cabinet

Ride Base Assembly

Hex head screw (M10x35)

Page 4
  • Pull the ride assembly away from the monitor cabinet only sufficient to reach the connectors. (Take care not to stretch the wiring harness.)

Connector

Monitor Cabinet

  • Disconnect the connectors and move the ride assembly completely away from the monitor cabinet.

Removing the Header Assembly

The header assembly is high and has a forward centre of gravity, so it is important that at least two people are used to remove or fit the Header Assembly.

  • Remove 2off pozi head screws (M4x12), with flat and spring washers, and remove the connector cover plate.
  • Disconnect the connector.
Page 5
  • Remove 2off pozi head screws (M5x16), with flat and spring washers.
  • Remove the Header Assembly
Page 6

RIDE ASSEMBLY

DECALS

  • Remove the Horse Rear Decals (both sides of the horse).
  • Fit the new Horse Rear Decals (both sides of the horse).
  • Fit the new decals to the rear of the Ride Base.

New Decals

Page 7

HEADER ASSEMBLY

  • Remove the ten security screws (M5x16) and remove the header acrylic. (This part is no longer required).
  • Remove 2off pozi head screw (M4x12) and remove the Top Bracket. (This part is no longer required).

Pozihead screw — (maxi2)

Page 8
  • Fit the new top brackets with 4off torx security screws (M5x12 black), supplied.

Torx security screw (M5x12 black) \

  • Fit the new Header Acrylic with 10off torx security screw (M5x16 chrome), supplied.

Torx security screw (MBx16 chrome)

Torx security sorew (MBx16 chrome)

\ Torx security screw (M5x16 chrome)

  • Refit the Header Assembly.
  • Reconnect the connector.
  • Refit the Connector Cover Plate.
Page 9

MONITOR CABINET

Replacing the Decals

  • Remove all the old decals, except the Monitor Middle Lower Decal.

DO NOT REMOVE Remove

-—_|—. Remove (both sides)

| Remove

——— New (both sides)

| ~ New

> New

Page 10

Fitting the New Front Vac-Form

  • Fit the new Vac-Form Bracket with 2off torx security screw (M5x16 black), supplied.

Torx security screw (M5x16 black)

Torx security screw (M5x16 black)

Page 11

Replacing the Game PCB

  • Disconnect all the connectors on the Game PCB including the fan connectors.
Note: Some of the cables will be replaced with new cables (see illustration below)

will not be used on the new game PCB

  • Remove the 2off pozi head screws (M6x25) from the right hand end of the Game PCB. slacken the 2off pozi head screws (M6x25) on the left hand end and remove the Game PCB.

head screw NI} M6x25)

Page 12
  • Place the old and new game PCBs next to each other.
  • Remove 8off pozi head screws (M4x50) and remove the fans from the old Game PCB. (4 screws on each fan).

Pozi head screw (Mex25)

  • Fit the fans to the new Game PCB in exactly the same way up using 4off pozi head screws (M4x50). (2 screws on each fan).

Pozihead screw (M4x50)

THESE FANS MUST BE FITTED TO THE NEW GAME PCB OR IRREPERABLE DAMAGE WILL BE CAUSED TO THE NEW GAME PCB.

Page 13
  • Refit the new Game PCB and fully tighten the 4off pozi head screws (Mx25).
  • Connect the new cables linking the I/O boards to the Front Cover Boards, and the new HSB cable linking the two front cover boards.
  • Locate and separate the two way connector with yellow and black wires. This is located to the right of the Switchmode Power Supply.
  • Fit the new break out cable to the two way connectors and connect the other ends to the front cover boards, as shown in the diagram below.
Page 14
  • Refit the existing connectors to the I/O Boards and Front Cover Boards.
Note: When refitting the D Sub connectors to the Front Boards ensure that connector 2 is fitted to the board nearest the rear of the cabinet, and the connector retaining screws are fully tightened.
Page 15

Replacing the Repeater (Link) PCB

  • Remove 1off pozi head screw (M5x12) and remove the Link Cover Bracket.

Pozi head screw (M5x12

  • Remove 2off Pozi head screws (M4x12) and remove the Link PCB complete with mounting bracket.
  • Disconnect the connectors.

@

~ Pozi head screw (M4x12)

Page 16
  • Refit the new Link PCB complete with mounting bracket using the 2off pozi head screws (M4x12).

9)

Pozi head screw (M4x12)

  • Fit the new Communication cable.
Page 17

RE-ASSEMBLY AND TEST

  • Reasemble the Ride Assemblies to the Monitor Cabinet, taking care not to trap any wires.
  • Reconnect the Mains-In and switch ON.
  • Reinitialize both players. (see section 6-8 page 58 of the Operators Manual).
  • Reset all game settings to the required levels. (see section 6-7 ‘Test Mode’ page 47 of the Operators Manual).

CONVERSION IS NOW COMPLETE.

Page 18

NEW PART NUMBERS

OD

Item Description Part No

4FF2 Cabinet Side Decal (LHS)692-810
5FF2 Cabinet Side Decal (RHS)692-811
6FF2 Instruction (A) Decal692-896
7FF2 Cabinet Front (A) Decal692-815
8FF2 Monitor Vac-Form Upper Decal692-823
9FF2 Monitor Vac-Form Lower Decal692-898
10FF2 Cabinet Front (B) Decal692-816
1FF2 Cabinet Front (C) Decal692-817
26FF2 Number Decals (set)692-813
Page 19

Description Part No

1Horse Rear Decal (RHS)692-843
2Horse Rear Decal (LHS)692-842
3FF2 Base Decal692-850

en \ . ( « ——

| a

Item Description Part No

4Truss Cover692-861
6FF2 Signboard Cover692-860
7Centre Logo Decal692-863

14 Light Plate 692-862