CATHODE RAY TOMES

Time Crisis 2 Standard

Time Crisis (World, TS2 Ver.B) (Namco, 1996) · Manual · 76 pages · 51 sections · original scan

Page 1

8v000S06 ‘ON Hed “ATASIOSYd GAMOT1IOS 3YV TVANVW SIHL NI LNO LHS STIVLAG SHL LVHL SALLVYSdII SI LI ONY ‘SSWIL TV Lv ALSAVS YSWOLSND NIVLINIVW OL YOLVHAdO SHL 4O ALIMIGISNOdS3Y SHL SI 1] jenue|] S10}e19dO PIS Z SISIYD SINLL O2JWP2CU

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3

PORTABLE APPLIANCE TESTING

Please Note:

During testing of the machine with a portable appliance tester the insulation test will show a failure due to the fitting of two VDRs between Live/Earth and Neutral/Earth.

These components have been fitted to safeguard against high voltage surges that may occur on the mains supply to the machine and to comply with the EMC regulations.

To conduct an insulation test on this machine, the VDRs must be isolated from the circuit first.

Ensure that the VDRs are reconnected after the insulation test has been completed and before the machine is placed back into service.

The VDRs used have been specified and tested as safety critical components.

Page 4

GB) No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of phonographic recording, nor may it be stored in a retrieval system, transmitted or otherwise copied for private or public use, without permission from NAMCO EUROPE LIMITED.

While the information contained in this manual is given in good faith and was accurate at the time of printing. NAMCO EUROPE LIMITED reserve the right to make changes and alterations without notice.

This machine has been manufactured in accordance with European Community Directives, and has been tested and complies with the Directives 89/336/EEC and 72/23/EEC by the application of EN55014-1, EN55014-2 and EN60335-1 standards (see front of manual) and as such bears the C€ marking. Any changes or modifications to this machine must be in accordance with the European Directives. Any unauthorised changes to this product, may contravene such Directives.

Under some conditions of extreme external interference, e.g. radio transmissions, electrostatic discharge or mains bore transients, some degradation of performance may occur. However the machine will recover normal performance once the source of the interference has ceased or been removed Following abnormally high surges on the mains supply, the video monitor may need to be manualy reset by turning the machine OFF and back ON

Note:- If the game processor resets due to an interuption or reduction of the mains voltage any credits established may be lost.

This game is not a machine as defined by the Machinery Directive 89/392/EEC

SAFETY WARNING

In order to use this machine safely, be sure to read this Operators Manual carefully before installation, adjustment or use of this machine.

Whenever the owner of this machine entrusts dis-assembly, installation, adjustment or routine maintenance to another person, the owner should ensure that that person read the appropriate precautions and relevant sections of this manual before starting work.

In order that no accidents occur when the machine is in operation, strictly follow the notes on safety as described below.

This manual along with the Installation Manual (where applicable) form an integral part of the equipment and must be available to the operating and service personnel at all times.

This machine is for indoor use only and should only be used for the purpose intended.

Namco Ltd. bears no responsibility for accidents, injury or damage resulting from unauthorized changes to, or improper use of this machine

SAFETY NOTES

The following safety notes are used throughout this manual. Familiarize yourself with each of these notes and its meaning before installing, servicing or making adjustments to this machine.

WARNING /\ Warning denotes a hazard that could result in injury or death. Do not proceed beyond a
warning note until the indicated conditions are fully understood and met.
CAUTION © Caution denotes a hazard that could result in damage to the machine. Do not proceed beyond a
warning note until the indicated conditions are fully understood and met.

GENERAL SAFETY CONSIDERATIONS

Only operate this machine after checking that it has been installed correctly and in accordance with the manual.

If there is an error or problem with the machine, operation must be stopped immediately and the problem rectified before any further use.

Installation, service, adjustment or routine maintenance should be carried out by suitably qualified persons only.

For continued protection against fire hazard, replace fuses with the same type and rating. The use of other fuses or material is prohibited.

The power supply inside the monitor will remain hot and have areas of high voltage even though the machine has been turned OFF, and there is the possibility of burns or electric shock. Be careful not to touch these areas.

To prevent possible electric shock due to failure, this machine MUST be fitted with a securely connected EARTHED plug.

If at any time the mains supply lead becomes damaged, it must be replaced immediately.

Do not turn the power switch ON until the machine has been installed correctly. OPP PB BBB B- Before connecting the machine to the mains supply, ensure that the machine is set for the correct voltage and that the correct fuses are fitted.

Page 5

Va NOTES ON INSTALLATION

A NEVER turn the power to the machine ON until installation has been completed. ; + A In order to prevent possible electric shocks, be sure that the §i machine is connected to the mains with a securely connected

earthed plug. ;

So that customers are not injured by the movement of the machine,|1
ensure that there is as least 500mm separation between other7 1)|

machines or walls. ; Y, Y Y

In order to avoid damage to the machine due to mis-operation, ensureY7

that the voltage of the mains supply is 230volts AC. Gy MLL i

Note: If the location of this machine has a polished floor, it is recommended é KEES that rubber pads are fitted under the level adjusters to prevent the IW
machine sliding on the floor.SS\:

MQ

Note: In order to gain access to the Power Supply and CPU assemblies, make sure that the rear of the machine is separated from a wall or other machine by at least 500mm. NN

> BP BP BP B&B MOVING THE MACHINE

This machine is fitted with castors to make it easier to move. Take care when moving the machine on an inclined surface.

The Header Assembly has a forward centre of gravity, so it i fit or remove the Header Assembly.

important that at least two people are used to

The fitting position of the Header Assembly is high, and it is important that a means of reaching the height safely,without stretching, is available. (e.g. Steps, Step Stool etc.)

The overall height of the machine, with the Header Assembly fitted, is 2310mm. Take care of any overhead obstructions. (e.g. Light Fittings, Electric Cables etc.)

When moving the game, ensure that the game is dis-assembled into 3 parts: Monitor Assy, Ride Assy and Header Assy.

PB BP BP BP BP BB REMOVING AND REPLACING PARTS Adjustments or maintenance on this machine should be carried out by suitably qualified personnel only.

Do not make any alteration to this machine without prior approval. Doing so could cause unforeseeable

danger.

Only parts specified by Namco Europe Ltd should be used when replacing or repairing parts. (Including screws).

Ensure that the power to the machine is turned OFF before commencing any maintenance work. (Trouble shooting, repairs etc.)

If performing work not described in this manual, be sure to contact your distributor for instructions, as no responsibility will be accepted for damage or injury.

Parts of the Power Supply and Monitor remain hot and carry high voltage even after switching OFF and could cause burns or electric shock. Take care not to touch these parts accidentally.

Make sure that the machine is switched OFF before connecting or disconnecting any plugs or connectors.

When removing the mains connector from the machine, or the mains plug from the wall outlet, always grasp the plug and not the cable. ~\

Page 6

Dieses Dokument darf in keiner Weise vervielfaltigt werden. Jegliche Tonaufnahmen sowie die Speicherung auf Datentrager (Suchsysteme), die Weitergabe oder sonstiges Kopieren fur den gewerblichen und privaten Gebrauch sind untersagt und bedirfen der vorherigen Genehmigung durch NAMCO EUROPE LIMITED

Die informationen in diesem Handbuch entsprechen den Tatsachen bei Drucklegung. NAMCO EUROPE LIMITED behait sich jedoch das Recht zu Anderungen ohne vorherige Bekanntgabe vor.

Dieses Gerat tragt das CE-Zeichen und wurde gem den EU-Richtlinien produziert. Es erfillt die Richtlinien 89/336/EEC und 72/23/EEC und Standards EN 55014, EN55104 und EN60335-1 (s. Deckblatt des Handbuches). Alle Veranderungen an diesem Gerat missen in Ubereinstimmung mit den EU-Richtlinien erfolgen. Nicht genehmigte Veranderungen an diesem Gerat verstoRen gegen diese Richtlinien

Extreme auRere Stérungen, wie z.B. durch Radiobetrieb, elektrostatische Entladung oder zeitweilige Netzschwankungen kénnen zu einer Leistungsminderung fuhren. Sobald diese Faktoren jedoch ausgeschaltet oder beseitigt wurden, erreicht das Gert seine normale Leistung

Achtung! Falls der Spielprozessor auf Grund von Netzunterbrechungen oder Abnahme der Netzspannung aussetzt, kann es zum Verlust von Spielkrediten kommen

Dieses GerAt fallt nicht unter die Maschinen-Richtlinie 89/392/EEC

SICHERHEITSHINWEISE

Um einen ordnungsgemagen Betrieb dieses Gerates zu gewhrleisten, mu vor Aufstellung, Inbetriebnahme und Gebrauch das Handbuch sorgfaltig gelesen werden. Sobald der Besitzer dieses Gerates die Demontage, Aufstellung, Inbetriebnahme oder den Service einer anderen Person Ubertragt, muB er sicherstellen, da diese Person vor Arbeitsbeginn die ndtigen Sichetheitshinweise und die dazugehdrigen Kapitel des Handbuches liest und versteht Um jegliche Unfalle wahrend des Betriebes zu vermeiden, missen obige Hinweise strikt befolgt werden Dieses Handbuch sowie das spezielle Gerate-Handbuch (wenn vorhanden) gehéren zum Gerat und mlssen dem Betreiber und Wartungspersonal stets zugainglich sein. Dieses Gerat ist ausschlieflich fur den gewerblichen Gebrauch in geschlossenen Raumen bestimmt und darf nur dort betrieben werden. NAMCO LTD. dbernimmt keinerlei Haftung flr Unfalle, Verletzungen oder Beschadigungen, die auf nicht genehmigte Verainderungen oder unsachgemafen Betrieb des Gerates zurlickzufuhren sind.

SICHERHEITSHINWEISE

Folgende Sicherheitsbegriffe werden im gesamten Handbuch benutzt. Machen Sie sich daher bitte vor Inbetriebnahme, Wartung und Durchfihrung von Einstellungen am Gerat mit diesen Warnhinweisen vertraut.

WARNUNG A WARNUNG bezeichnet eine Gefahrenquelle fiir Leib und Leben. Erscheint dieser Warnhinweis, darf erst weitergearbeitet werden, wenn die entsprechenden Erklarungen vollstandig verstanden und befolgt wurden.

VORSICHT © VORSICHT bezeichnet eine Gefahrenquelle fiir die Beschadigung des Gerates. Erscheint dieser Warnhinweis, darf erst weitergearbeitet werden, wenn die entsprechenden Erklarungen vollstandig verstanden und befolgt wurden.

ALLGEMEINE SICHERHEITSHINWEISE

Das Gerat darf nur betrieben werden, nachdem es vorschriftsmaig und in Uberei aufgestellt wurde. immung mit dem Handbuch

Die Warnschilder miissen in gutem Zustand sein und ersetzt werden, wenn sie nicht mehr gut lesbar sind.

Bei Auftreten eines Fehlers oder Problems muf das Gerdt sofort abgeschaltet werden und darf erst nach fachgerechter Behebung des Fehlers wieder in Betrieb genommen werden.

Aufstellung, Service, Einstellungen und Wartung dirfen nur von dafiir qualifiziertem Fachpersonal durchgefiihrt werden.

Zur Vermeidung von Feuer, defekte Sicherungen nur durch vorgeschriebene Sicherungen ersetzen. Die Verwendung von andersartigen Sicherungen oder unterschiedlichem Material ist untersagt.

Monitor bleibt nach Ausschalten des Gerates noch heif und fiihrt weiterhin Hochspannung. Daher besteht die Gefahr von Verbrennungen und Elektroschlagen. Diese Bereiche diirfen nicht beriihrt werden.

Zur Vermeidung von Elektroschlagen muf dieses Gerat mit einem ordnungsgema® geerdeten Netzstecker versehen sein.

Bei Beschadigungen des Netzteiles mu dieses umgehend ersetzt werden.

Gerat erst nach abgeschlossener Aufstellung einschalten.

Vor Einstecken des Netzsteckers bitte sicherstellen, da& Netzspannung und Geratespannung Ubereinstimmen, und die vorgeschriebenen Sicherungen verwendet wurden OP PBB BP BP BB BE

Page 7

Oo F BP &

Zur Vermeidung von Beschadigungen durch Fehlbetrieb am Gerat YH hl A sicherstellen, da die Netzspannung 230 Volt betragt. ESSE 7 4 SS . Hinweis: Ist das Gerat flr einen Aufstellplatz mit glattem Fu@boden bestimmt, Pree missen die Standbeine mit Gummiplattchen unterlegt werden, damit das N NSN MS SS | Gerat fest steht und nicht auf dem Boden hin- und herrutscht. SV _ 1 Hinweis: Zu Reparaturzwecken am Netzteil und den CPU-Komponenten muB die Riickseite des Gerates mindestens 50cm von anderen Geraten und der Wand entfernt sein. N w, HINWEISE ZUR AUFSTELLUNG

NIEMALS das Gert einschalten bevor die Aufstellung véllig abgeschlossen ist.

Zur Vermeidung von Elektroschlagen muf das Gerat mit einem ordnungsgemaf geerdetem Netzstecker an die Stromversorgung angeschlossen werden.

Um zu vermeiden, da& Kunden durch die Geratebewegungen verletzt werden, muf ein Sicherheitsabstand zu anderen Geraten und Wanden von mindestens 50cm eingehalten werden.

SPP BP Be &- Zum leichteren Transport ist das Gerat mit Rollen ausgeriistet. Daher besondere Vorsicht auf abschiissigem Boden

Der Schwerpunkt des Aufsatzes liegt sehr weit vorn. Daher werden fiir den Ab- und Aufbau des Aufsatzes mindestens 2 Personen bendtigt.

Der Aufsatz wird in groBer Héhe montiert. Daher mu8 aus Sicherheitsgriinden eine Steighilfe, wie z. B. eine Leiter, ein Tritt oder 4hnliches, verwendet werden.

Die Gesamthéhe de Gerates betragt 2.31m. Daher Vorsicht bei tiefer hangenden Beleuchtungskérpern.

Fir den Transport oder bei Fahreinheit inem Platzwechsel Gerat in drei Teile zerlegen: Kopfteil, Vorderteil, und

PBPBPBBPBPBP B&B AUS- UND EINBAU VON KOMPONENTEN UND TEILEN

Aufstellung, Service, Einstellung und Wartung diirfen nur von dafiir qualifiziertem Fachpersonal durchgefiihrt werden.

Es diirfen keierlei Veranderungen ohne vorherige Genehmigung am Gert vorgenommen werden. Zuwiderhandlungen stellen eine Gefahrenquelle dar.

Fir die Repartur diirfen nur Originalersatzteile (incl. Schrauben) von NAMCO EUROPE LTD. verwendet werden.

Vor Beginn aller Wartungsarbeiten (Fehlersuche, Reparaturen etc.) mu der Netzstecker gezogen werden.

Bei Arbeiten, die nicht in diesem Handbuch beschrieben werden, muf vorher der Handler zu Rate gezogen werden, da sonst keinerlei Haftung bei Beschadigungen und Verletzungen iibernommen wird.

Teile des Netzteiles und Bilschirmes bleiben nach Abschalten noch heif§ und fiihren Hochspannung. Dies kann zu Verbrennungen oder einem Elektroschlag fiihren. Diese Teile diirfen nich beriihrt werden.

Vor der Montage oder dem Entfernen von Steckverbindungen und Steckern mu das Gerat ausgeschaltet werden.

Bei Ziehen des Geratesteckers oder des Netzsteckers aus der Wandsteckdose stets den Stecker greifen und nicht das Kabel.

Page 8

Denne udgivelse ma ikke reproduceres af nogen som helst mekanisk, fotografisk eller elektrornisk proces eller i form af indspilning, den ma heller ikke lagres i et eftersagningssystem transmitteres eller kopieres til nogen form for offentlig benyttelse uden tilladelse fra Namco Europe Limited.

Da informationerne i denne manual er givet med god tro og var korrekt pa udskivningstidspunktet, forbeholder Namco Europe Limited sig retten til, at foretage eendringer og forandringer uden varsel

Denne maskine er frernstillet i overensstemmelse med Det Europaiske feellesskabs direktiver og er blevet testet og fuldendt med direktiverne 89/336/EEC og 72/23/EEC standarder (se manualens forside) og som sadan beerer CE meerket. Enhver form for aendring eller modiflkation af denne maskine skal vere i overensstemmelse med Det Europeiske feellesskabs direktiver.

| tilfeelde af forbigaende ekstreme eksterne forstyrrelser, sa som radio udsendelser, elektronisk afgivelse eller forstyrrelser pa ledningsnettet, kan nedbrydning forekomme. Maskinen vil dog kore normalt sa snart forstyrrelsen opharer eller bliver fjernet

Bemeerk:- Hvis spilleprocessoren resetter p.g.a. en forstyrrelse eller reduktion af hovedstrammen kan de etabledrede kreditter ga tabt.

Dette spil er ikke en maskine defineret af maskin direktivet 89/392/EEC -

SIKKERHEDS ADVARSEL

For at betjene denne maskine sikkert, las da denne brugemanual grundigt for installation, justering eller brug af maskinen. Nar som helst ejeren af denne maskine overlader demontering, installation, justeringer eller daglig vedligehold til en anden person, skal ejeren sikre sig at denne person lzeser de sikkerhedsregler og relevante punkter i denne manual for arbejdet begynder. For at undga ulykker nor maskinen er i gang, folg naje de sikkerhedsregler der er beskrevet herunder. Denne manual sammen med installations manualen er en ulaselig del af udstyret og skal altid veere til raidighed for det arbejdende og servicerende personale. Denne naskine er kun til indendgrs brug og ber kun bruges til det beregnede formal. Namco Ltd. baerer intet ansvar for ulykker eller skader som er et resultat af uautoriserede eendringer eller fejlagtig brug af denne rnaskine

SIKKERHEDSREGLER

De falgende sikkerhedsregler er brugt helt igennem denne manual. Ger dig bekendt med hver enkelt af dem og meningen heraf for installering, servicering eller justering af denne maskine.

ADVARSEL A Advarsel betegner en episode der kan resultere i skader eller dod. Begiv dig ikke forbi et advarselsskilt for de indikerede betingelser er fuldsteendig forstaet. FORSIGTIG (7) _ Forsigtig betegner en episode der kan resultere i adeleeggelse af maskinen. Begiv dig ikke forbi et advarselsskit for de indikerede betingeser er fuldstzendig forstaet.

GENERELLE SIKKERHEDSOVERVEJELSER

Betjen kun maskinen efter at have tjekket, at den er korrekt installeret og er i overensstemmelse med manualen.

Advarselsskiltene skal altid vere i god stand og erstattes hvis de er slidt, sa kunden tydeligt kan lease dem.

Hvis der er en fejl eller et problem med maskinen skal betjening straks stoppes, og problemet afhjzlpes for yderligere brug.

Installations service, justeringer eller daglig vedligehold bor kun udfores af en kvalificeret person.

For fortsat beskyttelse mod brandfare, sikres at hoved sikringerne kun erstattes med samme type kapacitet. Brug af anden kapacitet eller materiale er forbudt.

Stromforsyningen inde 1 monitoren vil forblive varin og have omrader med hej spending selvom maskinen har veret slukket og der er fare for brandskader eller elektrisk sted. Pas pa med at rore disse omrader.

For at undga elektrisk sted p.g.a. en fejl skal denne maskine vere forbundet med et sikkert jordstik.

Hvis hoved ledningerne pa noget tidspunkt bliver beskadiget skal de strakt erstattes.

Tend ikke for strommen for maskinen er korrekt installeret. OPBEP BBPBB BE

For tilslutning af maskinen til hovedstrammen sikres, at maskinen er indstillet til den rette spaending.

Page 9

OB BBE

BEMARK : Hvis denne maskine placeres pa et poleret gulv, anbefales det at ligge SX WN Shae S PUNKTER OM INSTALLATION T

Taend aldrig for strommen til maskinen for installering er fuldfort.

For at undga mulige elektriske sted sikres, at maskinen er forbundet til hovedstrommen med sikkert monterede jordstik. For at kunder ikke kommer til skade ved spillets beveegelser sikres, at / —y der er mindst 50cm afstand til andre maskiner og vegge. Z “wy For at undga skader pa maskinen p.g.a. fejlbetjening sikres, at spaendingen [7 GY pa hovedstrammen er 230 volt AC. tp LEAS

gummimatter under justeringsfadderne for at undga at maskinen SS Ws Glider pa guivet. > SS WL . MSALAALLAY

BEMERK : For at fa adgang til stromforsyningen og CPU justeringer sikres, at

bagsiden af hoved kabinettet star adskilt fra andre maskiner eller veeggen med mindst 50cm. Ne wy

(— >) Z\_Maskinen er smurt med olie for at gore den lettere beveegelig. Pas pa nar maskinen flyttes pa en skra overflade.

Z\ _ Hoved sektionens forreste center er meget tung, det er derfor vigtigt, at mindst 2 personer benyttes til at montere el. flytte hoved sektionen.

Z\_Monterins hojden af hoved sektionen er meget hgj og det er vigtigt, at have hjzlpemidler til at na sikkert uden at skulle straekke sig. (fek.s. trapper, trappestole el. lign.).

Z\ _ Den fulde hojde af hoved sektionen er 2.31 m. Pas pa ovre forhindringer f.eks. lys inventar.

A\ Narspillet skal flyttes eller bares skal det sikres at den er demonteret i 3 dele: - Hoved sektion - Front sektion - Kore sektion Ne w (— >)

PB BP BP BP PBB AT FJERNE OG UDSKIFTE SEKTIONER OG DELE.

Justeringer eller vedligehold af denne maskine bor kun udferes af kvalificeret personale.

Skift ikke noget pa maskinen uden godkendelse, det kan fore til uforudset fare.

Der ber kun bruges dele specificeret af Namco Europe Limited nar der skiftes eller repareres dele (inklusiv skruer).

Serg for, at strammen til maskinen er slukket for der foretages nogen form for arbejde (fejlfinding, reparation etc.)

Hvis der foretages arbejde der ikke er beskrevet i denne manual, kontakt da din leverandor for at fa kyndig vejledning, da intet ansvar vil blive accepteret ved skader.

Dele af stramforsyningen og monitoren forbliver varme eller bzrer haj spznding selv efter maskinen er slukket, det kan fare til forbraendinger eller elektriske stod. Pas pa ikke at rore disse dele ved et uheld.

Leg marke til at maskinen er slukket for samlinger eller stik tages ud eller szttes i.

Nar hovedsamlingen fjernes fra maskinen eller hovedstikket fjernes fra veggen, tag da altid ved stikket, ikke ledningen.

Page 10

© No se permite la reproduccién total ni parcial de esta publicacién por ningun medio mecanico, fotografico o electrénico, grabaciones fonograficas, ni su almacenamiento informatico, su transmision o su copia, ya sea para uso pUblico o privado, sin permiso de NAMCO EUROPE LIMITED

Si bien la informacion contenida en este manual se da de buena fe y es correcta en el momento de su impresion, NAMCO EUROPE LIMITED se reserva el derecho de hacer cambios y alteraciones sin previo aviso.

Esta maquina ha sido fabricada seguin las directrices de la Comunidad Europea, ha sido probada, y se ajusta a las directrices 89/336/EEC y 72/23/EEC, mediante la aplicacién de los estandares EN65014, EN65104 y EN60335-1 (véase cubierta del manual) y por ende lleva el sello de la C.E. Cualquier cambio 0 modificacién que se haga a esta maquina ha de ajustarse a las directrices de la Comunidad Europea. Cualquier cambio no autorizado hecho al producto pudiera contravenir estas directrices

Bajo ciertas condiciones de extrema interferencia externa, p. ej. transmisiones de radio, descargas electrostaticas u oscilaciones de la red eléctrica puede tener lugar un descenso del rendimiento. No obstante, la maquina recuperara su rendimiento normal una vez que la fuente de interferencias sea retirada o cese de producirlas.

Nota: Si el procesador de juegos se reinicializa a causa de caidas o interrupciones en la alimentacion eléctrica, se perderan todos los créditos.

Este juego no se ajusta a la definicién de maquina de la Normativa de Maquinaria 89/392/EEC

AVISOS DE SEGURIDAD.

Para utilizar esta maquina con seguridad, lea cuidadosamente este Manual de Operador antes de proceder a la instalacion, ajuste o uso de esta maquina, Cada vez que el propietario de esta maquina confie a terceros su desmontaje, instalacién, ajuste o mantenimiento Tutinario debera asegurarse de que tales personas lean las precauciones adecuadas y las secciones relevantes de este manual antes de comenzar su trabajo. Para que no ocurra accidente alguno mientras la maquina se encuentre en funcionamiento, siga estrictamente las notas de seguridad tal como mas adelante se describen. Este manual, junto con el Manual de Instalacién (cuando proceda), forma parte integral del equipo y debe estar a disposicién del personal de mantenimiento y operacién en todo momento. Esta maquina es unicamente para ser usada en interiores, y solo debe usarse para aquello para lo que ha sido creada. Namco Ltd. queda exenta de cualquier responsabilidad por accidentes, heridas o dafios causados por cambios no autorizados 0 uso indebido de esta maquina.

NOTAS DE SEGURIDAD.

En este manual se usan las notas siguientes. Familiaricese con cada una de ellas y su significado antes de instalar, revisar, o hacer ajustes en esta maquina.

AVISO. /)\ Aviso sefiala un riesgo que puede ocasionar lesiones o la muerte. Tras ver esta nota, no continue hasta entender completamente y cumplir las condiciones exigidas. PRECAUCION. (0) Precaucién sefiala un riesgo que puede ocasionar dafios a la maquina. Tras ver esta nota, no continue hasta entender completamente y cumplir las condiciones exigidas.

CONSIDERACIONES GENERALES DE SEGURIDAD.

Opere sélo con esta maquina tras comprobar que ha sido instalada correctamente y de acuerdo con este manual.

Las notas de aviso deben mantenerse siempre en buen estado y reemplazarse si estuvieran desgastadas para que los usuarios puedan leerlas con claridad.

Si hubiera algtin error o problema con la maquina, debe interrumpirse su operacién inmediatamente, y subsanar el problema antes de volver a usarla.

Las revisiones de instalas cualificado. n, los ajustes, y el mantenimiento rutinario deberan Ilevarse a cabo sélo por personal

Para asegurar una continua proteccién contra riesgo de incendios, asegtirese de que los fusibles eléctricos sean reemplazados solamente por otros del mismo tipo y especificaciones. El uso de otros fusibles o material esta prohibido.

La fuente de alimentacién del monitor se mantiene caliente, y tiene zonas de alto voltaje incluso cuando la maquina ha sido desconectada, existiendo el riesgo de quemaduras y descargas eléctricas. Tenga cuidado de no tocar estas zonas.

Para evitar posibles descargas eléctricas por cortes, esta maquina debe estar provista de un enchufe debidamente conectado, con TOMA DE TIERRA.

Si en cualquier momento el cable de alimentacion se dahara, debera ser reemplazado inmediatamente.

No encienda el interruptor de la maquina hasta que ésta haya sido correctamente instalada.

Antes de enchufar la maquina a la red eléctrica, asegirese de que la maquina esta preparada para el voltaje correcto, y de que se usan los fusibles adecuados OBB BP B BBB BBE

Page 11

O FP BB NOTAS DE INSTALACION.

JAMAS ENCIENDA la maquina antes de haber completado la instalacion.

Para evitar posibles descargas eléctricas, aseguirese de que la maquina esta conectada a la red con un enchufe provisto de toma de tierra.

Para que los usuarios no sufran lesiones debido al movimiento del s juego, asegurese de que hay al menos 500 mm de separacién entre Z, éste y otras maquinas o las paredes. Para evitar dafios a la maquina causados por operacién incorrecta, oy aseglirese de que el voltaje de la red es de 230 voltios, corriente alterna. GO WLLL 4 WY i Z A Notas: Sil lugar donde se instalara la maquina tiene un piso pulido, se KKK recomienda colocar tacos de goma bajo los ajustadores de nivel para. NN NN IN \ evitar que la maquina se deslice por el suelo. SS \ . Notas: Para acceder a las unidades de Fuente de Alimentacién y CPU, NVHHNYKHUAS asegiirese de que la parte trasera del mueble principal esta separada de muros u otras maquinas al menos 500 mm

Va El juego tiene ruedecitas para hacer mas facil su traslado. Tenga cuidado al mover la maquina en una superficie inclinada.

La Unidad de Igualacion tiene el centro de gravedad desplazado hacia adelante. Es importante que su montaje y desmontaje se haga por al menos dos personas.

La posicion de la Unidad de Igualacion es bastante alta, y es importante que haya un medio de alcanzar su altura con seguridad, sin estirarse (p. ej. una escalera, un taburete, etc.)

La altura total de la Unidad principal es de 2.31 mm. Tenga cuidado de que no haya obstaculos p. ej. luces.

Cuando traslade o mueva el juego, aseguirese de que éste haya sido desmontado en 3 partes: Unidad de Igualacion, Unidad Frontal, y Unidad de Juego.

> BP BPBPBPBP BP B&B RETIRAR Y REEMPLAZAR PARTES Y UNIDADES. >

Las revisiones de instala personal cualificado. n, los ajustes, y el mantenimiento rutinario deberan Ilevarse a cabo sélo por

No realice alteraciones en esta maquina sin aprobacién previa. De hacerlo asi, pueden causar peligros imprevisibles.

Sélo deben usarse las partes especificadas por Namco Europe Ltd. para reparaciones o reemplazos {incluidos los tornillos).

Aseglirese de que la maquina esta desconectada antes de comenzar cualquier trabajo de mantenimiento (reparaciones, resolucién de problemas, etc.)

Al realizar trabajos no descritos en este manual, péngase en contacto con su distribuidor para recibir instrucciones. Se declina cualquier responsabilidad por dafios o lesiones.

Hay partes de la fuente de alimentacién y del monitor que se mantienen calientes o almacenan alto voltaje incluso tras desconectar la maquina, y pueden producir quemaduras o descargas eléctricas. Tenga cuidado de no tocar accidentalmente estas partes.

Aseglirese de que la maquina esta apagada antes de conectar o desconectar cualquier enchufe o conector.

Al retirar el conector principal de la maquina, o la clavija de alimentacién del enchufe de la red, agarre siempre la clavija y no el cable. )

Page 12

©) Aucun élément de cette publication ne sera reproduit, ni par procédé mécanique, photographique ou électronique, ni par un moyen d'enregistement phonographique. Ces informations ne seront ni stockées grace a un procédé de récupération, ni transmises ou autrement copiées pour un usage publique ou privé, sans l'autorisation de NAMCO EUROPE LIMITED.

Malgré le fait que les informations contenues dans ce manuel soient données de bonne foi et étaient actualisées au moment de leur impression, NAMCO EUROPE LIMITED se réserve le droit de procéder 4 des changements ou a des modifications sans avis préliminaire.

Ce jeu a été fabriqué en respect des normes de la Communauté Européenne, aprés avoir été testé il répond aux normes 89/336/EEC et 72/23/EEC, en application des standards EN55014, EN55104 et EN60335-1 (voir la couverture du manuel), et comme tel il comporte l'autocollant de conformité avec les normes de la Communauté Européenne. Tout changement non autorisé sur ce produit pourrait contrevenir a ces normes.

Sous certaines conditions extrémes d’interférence exteme, par example des transmissions radio, des décharges électrostatiques ou bien de interférences passagéres sur le réseau, certaines dégradations ou anomalies peuvent se produire. Le jeu retrouvera cependant son état normal de fonctionnement lorsque la cause de ces anomalies aura cessé ou se trouvera déplacée.

Note:- Si le processeur du jeu se reprogramme suite a une interruption ou une réduction de l'alimentation, les crédits qu'il aurait pu contenir peuvent se trouver perdus.

Ce jeu n’est pas une machine, telle que définie par la norme sur les machines 89/392/EEC

MESURES DE SECURITE

Afin d'utiliser ce jeu en toute sécurité, bien lire ce manuel d'utilisation avant de procéder a son installation, son réglage ou son exploitation. Si le propriétaire de ce jeu en confie la démontage, installation, le réglage ou la maintenance habituelle a une autre personne, il devra s’'assurer que cette personne ait lu les conseils d'utilisation et les passages du manuel se rapportant a ce theme, avant qu'elle ne commence son travail Afin d’éviter tout accident pendant la durée d’exploitation de ce jeu, se conformer strictment aux conseils de sécurité décrits a la suite. Ce manuel ainsi que le manuel d'installation du jeu (la ou nécessaire) font partie des éléments nécessaires a l'installation de la machine et doivent étre mis a la disposition de l'utilisateur et du personnel de maintenance a tout moment. Ce jeu est uniquement destiné a un usage intérieur et devra étre utilisé comme tel. Namco Ltd. ne sera aucunement tenu responsable en cas d’accidents, de blessure ou de dommage quelconque résultant de modifications non autorisées ou d'usage impropre du jeu

REMARQUES SUR LA SECURITE

Les termes de sécurité détaillés a la suite seront utilisés tout au long de la lecture de ce manuel. II convient de vous familiariser aves chacun de ces termes ainsi que leur signification avant de procéder a installation, a la maintenace ou au réglage du jeu.

AVERTISSEMENT /\ Ce terme annonce un danger qui pourrait éventuellement avoir des conséquences dommageables ou mortelles. Ne pas passer ofitre ce signal jusqu’a ce que les. conditions indiquées soient entiérement comprises et effectuées.

ATTENTION O) Ce terme indique qu’un danger menace la machine. Ne pas passer oiitre ce signal jusqu’a ce que les conditions indiquées soient entiérement comprises et effectuées.

CONSIGNES GENERALES DE SECURITE

Allumer l'appareil seulement aprés avoir vérifié qu’il a été correctement installé, et que les instructions du manuel ont été respectées.

Les notes de mise en garde doivent constamment demeurer en bon état et étre remplacées en cas de disparition, afin que le client puisse les lire clairement.

S’il y una erreur ou un probléme avec la machine, l'utilisation doit étre immédiatement interrompue et le probleme résolu avant toute nouvelle utilisation.

L’installation, le service, le réglage, ou la maintenance doivent étre effectués uniquement par les personnes qualifiées.

Afin d’éviter un éventuel incendie, s’assurer que les fusibles soient remplacés par le méme type de fusibles et au bon voltage. L’utilisation d’autres sortes de fusibles ou autres matériels est interdite.

Lalimentation a l’intérieur du moniteur reste chaude et comporte des zones de haute tension méme si la machine est éteinte. II existe donc un risque de brulure ou d’électrocution. Attention a ne pas toucher ces endroits.

Pour prévenir une éventuelle électrocution due a un défaut matériel, ce jeu DOIT étre muni d’une prise de TERRE connectée en toute sécurité

Si a tout moment les fils électriques sont endommaggés, il faut les remplacer immédiatment

Ne pas mettre le jeu en mode de fonctionnement avant qu’il n’ait été correctement installé. OPB BPBBBBBB

Avant de connecter la machine au réseau, s’assurer que la machine est installée sous la bonne tension et que les fusibles correspondent.

Page 13

Oo bP BB

Note:
Note: NOTES D’INSTALLATION

NE JAMAIS mettre le jeu en marche avant que l’installation ne soit complétement effectuée.

Afin de prévenir une éventuelle électrocution, s’assurer que la machine est connectée au réseau avec une prise de terre reliée selon les normes de sécurité.

Afin que les clients ne soient pas blessés par les mouvements du jeu, s’assurer qu’il existe au moins 500 mm de séparation L,

230 volts AC. aves les autres jeux ou les murs. Wy Afin d’éviter que la machine ne soit abimée suite & une mauvaise ZA ;

opération, s’assurer que la tension sur le réseau principal soit de Gin V4

SN Si l'endroit ot doit étre installée la machine a un sol pdli, il est Parauaay SS SX recommandé de poser des tampons feutrés sous les vérins pour NX . MX ny éviter que le jeu ne glisse sur le sol N Afin de facilité 'accés aux CPU at a l'alimentation, s'assurer qu'il y a un espace d’au moins 500 mm entre l'arriére du meuble et le mur ou tout autre jeu

> BP BP BE B& Le jeu est foumi avec des roulettes pour une meilleure mobilité. Prendre garde quand la machine est déplacée sur une surface inclinée.

Le centre de gravité de la partie supérieure du jeu est situé sur l’avant, il est donc indispensable que deux personnes au moins soient employées pour installer ou déplacer la partie supérieure.

L’installation de la partie supérieure du jeu s’effectue en hauteur, il est donc important d’utiliser un élevateur quelconque pour en effectuer le montage.

La hauteur totale de l’'assemblage principal est de 2310 mm, prendre garde aux encombrements de la partie supérieure (ex : illuminations du bandeau).

Quand le jeu est déplacé ou transporté, s’assurer qu’il est séparé en 3 parties: l'assemblage du haut (le bandeau), 'assemblage de devant (la cabine), 'assemblage mobile.

SPP BP BP BP BP BP BE DEPLACER ET REMPLACER LES UNITES ET LES PIECES DETACHEES.

Liinstallation, le service, le réglage, ou la maintenance doivent étre effectués uniquement par les personnes qualifiées.

Ne pas apporter de modifications sur cette machine sans autorisation préalable, faute de quoi cela pourrait entrainer un danger.

Seules les piéces détachées Namco Europe Ltd. doivent étre utilsées pour le remplacement ou la réparation de piéces (y compris les vis)

S’assurer que l’interrupteur soit sor OFF avant de commencer tout travail de maintenance (localisation d'une panne, réparations, etc.)

Si dans ce manuel il manque une information pour réaliser un quelconque travail, contacter votre distributeur, car aucune responsabilité ne sera acceptée en cas de domage ou de blessure.

Les piéces de I’alimentation et du moniteur restent chaudes, a tension élévée méme lorsque la machine est hors tension, elle pourrait occasionner des brdlures ou des électrocutions. Attention de ne pas toucher ces endroits accidentellement.

S’assurer que la machine soit hors tension avant de brancher ou débrancher toute prise ou connecteur.

Lorsque l'on manipule la prise au réseau de la machine, ou lorsque les prises principales doivent étre débranchées, saisir toujours la prise, et non le cable.

Page 14

Kavéva népog auriig tng ExBoong dev unopei va avanapaxSei ue onoLodijmore UNXavIKS uroypapIKd F NAEKTHOVIKS EGO , | UE HOPHH PwvNTIKHs NXdyPaoNaNS Kal OUTE va aTloONkeuTE! Ue ErtavopBOTIKO GUOTHHA , va LeTAdoBEI h Va avriypagel Vid Snuoowa H (Slatin xoNON , kapig Thy dela Tne NAMCO EUROPE LIMITED. Ka®dc autéc ot MAnpodopies oe auTé To eyXelpidio Exouv Soe! pe KAAI Tom Kat akpIBAg THY dpa THs TUTWaNS . etal SMEG EUROPE LIMITED Kpataet To Sikaiwpa va Kdvel onoleddinote adAayés xwpig etdoroinon.

Ta unxavijuata éxouv KataokeuaaTei GUUpwva HE Tous Spous TNS Eupunaikrs KowvotNTaG , Kal ExouV eheyxGei GULPwva lle ToUg vouloUG 89/336/EOK kav'72/23/EOK pe hv aitnon tov EN55014 , EN55104 kat EN60335-1 otavtapte (Seg UMpoaTa ato eyxEIpid10) Kat dha Exouy To CE ofua . Qnoiadiytote aNAayi fl UeTaTpOMT OE AUTO TO LNXAVNHG TipEMet va eival oULowva Ue TOU dpoug THs Eupwnaikig KolvoTntac. Onoleddirtote aAAayés Xwpic Gdela Ge GUTO To NPoioV Nope: va TapaBei avTOUe tous dpous. Ze KaNolEs MepiNTdaEIG UMEPBOAIKHS EEwTEpIKTS TAPEUBOAIS ,TLX. PAdlopwvikés HETAddazIG , NAekTpOTATIKES UeTaBoAse n MapodiKés eUBOAEC , urtopel va NapoUotaaToUY Kanoleg aBNOtHTES OTH. NapoUoiamn . Tlayrag To Lnxavnia Ja eTravEABEL OTHY PUTLOAOY IKI} TlapoUGiaaN E> daov N TMYH THg NapeLBoAts oTapatiaet h antowakpuveei . Enciwon : Eav yivet reset otov processor Tou UNXavi}HaTOS KATA TH dtapKeta THS KUPLag MapoXIG , MevTOI Tou xouV kepdnGei unopet va xaBowv.

Auté To naixvidi dev eivat pNXavnya dws NposdiopiZeTat and Tous Spous MnXavnLatwv 89/392/EOK .

OAHTIEZ AZOAAEIAE

Tia Ty aogadh Xpron Tou uNXavijLATos , Pentel va StaBageIg To eyXetpidto Xprang MpoGEKTIKA Tplv THY EYKATaoTAGN sTonoBETHON H} XPrIGN Tou LINXavALATOG. Onotedijnote o BioKTTNg AUTON ToU {InXavi|LaTog {nTaet ANS KdrIoLo MPdgwNO va EyKATAOTHOEL , va KavEl OTIOLAdIITOTE addayi 1 ékeyXo pouTivag oto uNXavnya , Tipénet Va eivat diyoupos Tt Exel StaBacel Tig OdNYieg aUTOU TOU eyXEIpLdiou Til va apxioet va SouAevet . Mog anoguyry onotoudi\note atuxrHatos Kata Thy Aettoupyia Tou UNXaVviLATOS , aUoTHPwS akoAoUBOUVTaL ot Odnyies aopdAciag orwg Sivovtat napakatw . AUTO To eyXElpId10 GE GUVUGOHS HE To eYXEIpidIo EyKaTaOTAONG (dro SaTiBeTaI) antoTeAEi Eva OhOKANPwLEVO HEPOS Twv NapoX@V kal MIpéntet va Eivat SiadEoiyo yia hv Aettoupyia Kal To service onolddrnote OTL LN}. Auté To uNXavnua eivat yia Xpr}on HOVO Ge EowTEPIKS XdPO Kal Ba NPENEL va XPNOWOTOIEITAL LdVO Yia Tous AdYouS ya Tous onoious KatackeuaoTKe H etatpeia NAMCO Ltd dev $épet Kapia evddvn yia atuXMWaATA , MANYés H} KaTaoTPOpEs TOU LTTE! Va MPOKANBobV aNd adAayég Xupig Geta o€ 1H eicaywyeig autou Tou "NXavF|LAToS.

ZHMEIOZEIZ AZOAAEIAE

Ol akdAouses onHEIdoEIG apaAEIAG XPNOIPOTIOLOUVTAL HEOWw aUTOU TOU syXEIPIBioU . AldBavEe aUTEs MPOTEKTIKA Via va yivet katavonto To VonUa Tous Miplv THY EYKaTaOTAN , GépBig H OIOIGdH|TIOTe GAAayH Yivet oto UNXavnG.

MPOEIAONOIHSH /\ H mpozi3oroinan apopa KivSuvo 0 onoiog unopei va eivai Adyos Bavarou . Na unv Mpoxwpraeig o£ ono1adiore Kivnon YEXpI auToi o1 Spot yivouv KaTavonroi.

MPOZOXH (0) H mpocoxr apopa kivuvo o onoiog unopel va npoKadgoei MpSBANuA oto NXavnua . Na UNV TpoXwpraeig Ge ortoLadijNoTe Kivnon HEXeL AUTO! ot Spot yivouv katTavontoi.

E=ETAZH FENIKHE AZ@AAEIAE Agou éXe1 Katavon@ei aura To eyXeIpidi0 , HvO ToTE va AsIToUpynoe! To NXAaVvNHG A va yivel EAEYXoG E> dooV éxe1 yiver n eykataoTaon.

O1 nposiSoroijosig npénel va HEvouV KaBapéc Kal GE KAAA KaTdOTAGN Hote o TEAATHG va TIC SiaBaZE1 KaBapA.

Eav undpxet AdGoc Fh MpOBANuG HE To HNXavNuA , n Actroupyia npénel va oTapaTae! ayEous Kal va SiopOdveral To A&Bog NplVv ono1adinoTe GAAN XpHjon.

Eykaraotaon , petatpomi h EkeyXog pouTivas propei va yiveral povo and eEoucIodoTnHEva ATOLL .

Tia ouvexi npootacia and gwrid , npéne! of aopaAciEG va avTIKaBIoTOUVTAI WE idIoU TUTOU .H Xpijon GARY aopaAsiov f avTIKeINévwv anayopsuETal.

To Tpopodorikéd oto cowrepiKd Tou pNXaVvHaTos Ga Napaysiver ZeoTS Kal UNapXoUV NEpIoxés PE UNAH Tacn Trap’dA0 Tou To pnXavnya dev SouAevel , kal UNGpXel N MIBaVeTNHTA NAEKTPIKOU Gok . Mpogoxh va "NV akouuNEIG autéc Tic Meploxéc.

Tia Thy anoguyh nAcktpikdv GoK Adyo BAGBNG , To yNXavnya MPENE! va éxe1 npwra evwOei pe yeiwon.

Eav kanoia otiypn Kataotpadgei n KUpia MapoX! , Mpénel va avTikaTaoTaGEi apnéows.

Na pnv avawel To unxavnua (switch ON) péxpl va éXe1 eyKaTaoTaBei word Kal TARPS.

Mew thy rapoxl pedpatos oto yNXAvNH , va sicat diyoupog Ott Ta voltage Kal SAEs ol GapAAEIES Eival CwWoTE evwpéva kat TonoBeTnHEva OBBB B BB BB BG

Page 15
A\NOTE va unv avaBer To unxavnua eav Sev éxe! ohoKANpwAei nGYYyyA
eykaTaotaon.jfUyYZ
A\Tia tay anoguys nAexrpiki oox npénei To wnxavqua va éxe1_

yelw@ei.

A\fia ny anoguys xivBivou oe Kanoiov naikrn , mpénet ro unxavquaay5

va éXe1 anécraan TouAaxioTov 500mm ané GAAo ynxavnya nh toixo. |" wy ‘

®amy anoguyy BraGng oto unxdvnUa AdyO AABOG Aettoupyiag ,YsYZ
Tipsnet n napoxn va eivat 230volt AC../Z

ZHMEIOSH: Eav to ndtwya oto onoio eivat tonoBeTNLEVvo To WNXavnua Yl hy ; NN ZHMEIOZH: Ta my ebKodn npdoBaon omy Kupiwg napoxi) H To CPU npénet SOS \ WN 1 niow népta Tou pnXavi|Watos va anéxet TOUAGXIoToV 500mm SMV Xe ZHMEIOZEIZ PIATHN ET KATAZTAZH

yAuoTpdei.eival KANG Va Bet &Va KOLHATI HOKETAG Via aMOgUYA, Letakivnong Tou unXaviwatos ev dpa Asttoupyiag Tou.

ané tov ToiXo GAAO ENXavna. NOON

bPBP BBE Oo pnxavnua sival epodiaopévo pe KapouAla yia THY E0KOAN HETaKivNaH TOU.

To endvw pépos Tou pNXaviapatos éxe1 emIMAZOV Papo ylauTS xpElaZovTal 3uo yia THY HETapopA.

H kegaAn (kamaxi) Tou uNXaviHaTOG cival MOAU WAS Kal ylauTS xXpElaZETaI MPoGoX! GTHY ToTOBETNGH Tou , Va pV XTUTHOEI KaTaoTPAgé;.

To ouvoAiKé Upog THs KeaAig cival 2310mm . Opevtice va pnv XTUTIGEI Ge AdyTEs K.A.T.

‘Orav petaxiveitar To uNXavnHG , Mpénel va cival oe 3 HEP: —_KepaA‘ (kaTaKi), MrpooTa pEpos (086vec), Ka@iopa

~

Va bP B BBP B BBE ANOMAKPYNEH KAI ANTIKATAZTAZH MEPON - ANTAAAAKTIKON

Eykardoraon , Hetatpomi A EAeyXos pourivas umopsi va yiveral Hove amd sEouoIoSoTHEVG Atop .

Asv npénet va yivovrai petatponés ora ynxavipara wpig éyKpion . Mnopsi va mpoKAN@ei anpaBAenTos, kivSuvos.

Mévo pépn rou StieuKpiviZovrai ar thy etaipeia NAMCO EUROPE Ltd prropowv va xenciponoindouv yia avtikatTaotaon fh emdidpewon. (oupTepiAayBavovte Kal o1 BidEc)

Na sivai ciyoupa KAcioTé To pedpa nplv onoladijnoTe SouAEIa oto yNXavnuG.

Eav yiver karrora SouAeid oro pNXavnya Xwpig va SicuKpIviceTal oTO eyXeipidI0 , va EMIKOIVOVIHOEIG HE Tov avtinpoowno via odnyies ylaTi kapia euBuVvN Sev PEpounE yia KaTaoTPOgES Nh BAGBES.

Mépn Tou TpopodoriKol f Tou HaviTop Napapévouv Zeora F EXouV UNAH TaON aKopA Kal Sta oBrE! TO UNXavnya Kal WTopouv va MpOKAAEGOUV KaWiHO f AeKTPOGOK.FaUTS Sev MpENel va EpxovrTal oe ENaph he xépia .

To unxavnua npérei va sivai oBnoté Kara thy o’vSEon H anoGwVSEGN NpiZaG f KovéKTOpa.

Kara Thy anopaKpuvon Twv KEvTpIKOV KOVEKTOp and To UNXavnHG A THs KUpiag MpIZag , MpéTel va TMIGVOUE To TAGOTIKG HEPOG Kal Ox! TO KAAWAIO. ~

Page 16

Gd) Nessuna parte di questa pubblicazione pud essere riprodotta con processo meccanico, fotografico o lettronico, né sotto forma di registrazione fonografica, nd pud essere memorizzata in un sistema di salvataggio, trasmessa o in altro modo copiata per uso pubblico o privato, senza l’autorizzazione di NAMCO EUROPE LIMITED.

Le informazioni contnute in questo manuale sono state date in buona fede ed erano accurate al momento della pubblicazione. Tuttavia NAMCO EUROPE LIMITED, si riserva il diritto di apporre cabiamenti e variazioni senza alcun preavviso. Questo apparecchio é stato costruito in conformita alle Direttive della Comunita Europea, ed é stato provato e soddisfa le Direttive 89/336/EEC e 72/23/EEC per l'applicazione degli standards delle norme EN55014, EN55104 e EN60335-1 (vedi fronte del manuale), e per questo porta il marchio CE. Qualsiasi cambiamento o modifica di questo apparecchio deve essere in conformita con le Direttive della Comunita Europea

In caso di condizioni di estrema interferenza dall’esterno, per esempio trasmissioni radio, scariche elettrostatiche o transitori sulla linea, pud verificarsi un decadimento delle prestazioni. Comunque l'apparecchio ritornera al rendimento normale quando la sorgente dell,interferenza avra cessato di emettere o sara stata rimossa.

Nota bene: se il processore del gioco “resetta” a causa di una interruzione o diminuzione del voltaggio di linea, un eventuale credito, gia concesso, pud essere annullato.

Questo goco non é una macchina cosi come viene definita dalla Direttiva Macchine 89/392/EEC.

AVVERTENZE PER LA SICUEZZA

Allo scopo di usare questo apparecchio in sicurezza, leggere questo Manuale dell’operatore attentamente prima dell'installazione, regolazione o uso di questa macchina. Tutte le volte che il proprietario di questo apparecchio affida lo smontaggio, l'installazione, la regolazione o la manutenzione ordinaria ad un’altra persona, il proprietario stesso deve assicurarsi che quella persona legga le precauzioni necessarie e i paragrafi importanti di questo manuale prima di iniziare a lavorare. Perché non succeda alcun incidente quando la macchina é operante, seguire rigorosamente le note sulla sicurezza come specificato piu avanti. Questo manuale insieme con il manuale di installazione (dove si pud applicare) forma una parte integrante dell'apparechio deve essere disponibile sempre al personale operante e di servizio Quest macchina deve essere usata solo in interni e deve essere usata solo per gli scopi per cui é progettata. Namco Europe Ltd non si assume responsabilita per incidenti, ferite o damni risultanti da cambiamenti non autorizzati o da uso improprio della machina.

NOTE PER LA SICUREZZA

Le seguenti note sulla sicurezza sono usate dal principio alla fine di questo manuale. Valutare attentamente ciascuna di queste note ed il loro significato prima di installare, fare assistenza o regolazioni su questa macchina.

WARNING /\ “Warning” evidenzia un rischio di ferita 0 di morte. Non procedere oltre una nota “Warning” finché le avvertenze specifcate non siano completamente capite e conosciute.
CAUTION (4) “Caution” evidenzia un rischio di danneggiare la macchina. Non proceder oltre una note “Caution” finché le avertenze specificate non siano completamente capite e conosciute

CONSIDERAZIONI GENERALI SULLA SICUREZZA

Mettere in funzione l’apparecchio solo dopo aver controllato che I’installazione sia stata effettuata correttamente ed in conformita alle istruzioni del manuale.

awvisi “Warning” devono sempre essere conservati in buone condizioni e sostituti se consumati, cosicché il cliente li possa leggere chiaramente.

Se vi sono errori o problemi con la machina, si deve interrompere il funzionamento immediatamente e risolvere il problema prima di ogni ulteriore uso.

L’installazione, ’'assistenza, le regolazioni e la manuzenzione ordinaria devono essere eseguite solo da persone idonee e qualificate.

Per una protezione costante contro il rischio di fuoco, assicurarsi che i fusibili sulle alimentazioni siano solo sostituiti con lo stesso tipo e caratteristiche. L’uso di altri fusibili o materiali é proibito.

L’alimentatore all’interno del monitor rimane caldo ed ha zone di alto voltaggio anche se la macchina é stata spenta, c’é quindi la possibilita di bruciature o scosse elettriche. Fare attenzione a non toccare queste zone. Per prevenire possibili scosse elettriche dovute a difetti, quest macchina DEVE essere installata con un connettore sicuramente MESSO A TERRA.

In caso il cavo di alimentazione di rete risultasse danneggiato deve essere sostituito immedatamente.

Non accendere la macchina finché la stessa non é stata installata completamente e correttamente. OPP BP BBBB BB

Prima di collegare la macchina alla rete, assicurarsi che la macchina sia preparata per il voltaggio corretto e che siano inseriti i fusibili adatti.

Page 17

O FP BPE

Note:
Note: NOTES D’INSTALLATION

NON ACCENDERE MAI Ia macchina finché l’installazione non & stata completata. iy 7,

Allo scopo di prevenire possibili scosse elettriche, la macchina Wt 5

deve essere obbligatoriamente collegata alla rete con un connettore messo a terra con connessioni sicure. Perch i clienti non siano feriti dal movimento del gioco, / assicurarsi che ci siano almeno 500mm di distanza rispetto alle 4 VW altre machine o rispetto al muro.

Per evitare danni alla machina durante la messa in opera, assicurarsi che il voltaggio della rete sia 230 volts AC. Y Yj Il luogo di destinazione della macchina deve avere il pavimento liscio ey Klis LG e si raccomanda di sistemare dei cuscinetti di gomma sotto i piedini di livellamento per prevenire lo sciovolament della machina sul pavimento.

Per garantire l'accesso all’alimentatore e alla scheda madre, assicurarsi che il retro del mobile principale sia separato dalla parete 0 da altre macchine di almeno 500mm.

>

> FP BP Be Il gioco é fornito di ruote per rendere pit facile il suo spostamento. Fare attenzione quando si muove la macchina su una superficie inclinata.

La testata ha il baricentro spostato in avanti, é percid importante che ci siano almeno 2 persone per montare o smontare la testata stessa.

sia un mezzo (Ad esempio La posizione di fissaggio della testata é molto alta, ed é importante che disponibile per raggiungere tale altezza in sicurezza e senza allungament scalini, scale portatili etc.)

L’altezza totale della parte principale é 2310mm, fare attenzione ad eventuali ostacoli sopra la testata owvero ad eventuali installazioni di luci.

Quando si muove o si trasporta il gioco assicurarsi che sia smantato in 3 parti: Testata, Parte frontale, Parte mobile S

PP BBB BB BEB RIMOZIONE E SOSTITUZIONE DI GRUPPI E PARTI STACCATE

Vinstallazione, l’assistenza, le regolazioni e la manuzenzione ordinaria devono essere eseguite solo da persone idonee e qualificate.

Non apporre alcuna modifica alla machina senza autorizzazione preventiva. II fare questo pud causare un pericolo non prevedibile.

Quando si rimpiazza o si Namco Europe Ltd. iparano delle parti (incluse le viti) si possono usare solo parti approvate dalla

Assicurarsi che la macchina sia SPENTA prima di incominciare qualsiasi lavoro di manutenzione (guasti, riparazioni etc.)

Se state per iniziare un lavoro non descritto in questo manuale, contattate il vostro distributore per instruzioni poiché non si accetta alcuna responsabilita per danni o ferite. Parti dell’alimentatore e del monitor rimangono caldi o portano alta tensione anche dopo aver spento Vapparecchiatura e possono causare bruciature o scosse elettriche. Attenzione a non toccare queste parti accidentalmente.

Assicurarsi che la macchina abbia l’interruttore nella posizione OFF prima di inserire o disinserire qualsiasi connettore o spina.

Quando vengono rimossi i connettori principali dalla macchina oppure la spina dell’alimentazione dalla parete bisogna sempre afferrare il connettore e non il cavo. w

Page 18

@)

Ingen del av denne utgivelsen ma reproduseres av noen mekaniske, fotografiske elle elektroniske prosesser, eller i form av fotografiske opptak, og ikke kan det lagres i et gjenvinnbart system, sendt eler kopiert for offentlig eller privat bruk, uten tillatelse fra NAMCO EUROPE LIMITED

Da informasjonen i denne manualen er gitt i god tru og var korrekt da den ble utgitt, tillegger NAMCO EUROP LIMITED seg retten til 4 lage forandringer uten varsel

Denne maskinen er produsert i samsvar med direktiver framsatt av det Europeiske samfunn. Maskinen er testet og samsvarer med direktivene 89/336/EEC og 72/23/eec med anvendelse av EN55014, EN55104 og EN60335-1 standarder (se i begynnelsen av manualen), og derfor baerer CE merket. Hvilken som helst forandring eller modifisering ma skje etter direktivene satt av det Europeiske samfunn. Uautoriserte forandringer pa dette produktet, kan motstride disse direktivene.

Under noen forhold av ekstreme ytre forstyrrelser, f.eks radio sendere, elektronisk utladning eller transiente spenninger, kan man regne med noe senket ytelse. Men maskinen vil oppna normal ytelse nar kilden til forstyrrelsene opphorer eller er fysisk fjernet.

Merk:- Hvis spillets prosessor resettes p.g.a et kutt eller reduksjon av hovedspenningen kan oppsparte kreditt pa spillet forsvinne.

Dette spillet er ikke en maskin som er definert ved Maskin direktivet 89/392/EEC.

Sikkerhets advarsel.

For a bruke denne maskinen uten noe form for fare, sorg for a lese denne manualen noye for installasjon, justeringer eller bruk av maskinen. Nar eieren av denne maskinen overlater avmontering, installasjon, justering eller rutine vedlikehold til en annen person, skal eieren forsikre seg om at denne personen leser de passende forsiktighetsreglene og relevante deler av manualen for han starter pa arbeidet For a forhindre at ulykker inntreffer nar maskinen er i drift, falg strengt teksten om sikkethet som beskrevet nedenfor. Denne manualen sammen med installasjons manualen (hvor det er anvendelig) er en intrigert del av utstyret og ma vere tilgjengelig for drift- og servispersonell til alle tider. Denne maskinen er bare for innendars bruk og skal bare benyttes etter mente hensikter. Namco Ltd. bzerer intet ansvar ved ulykker, kvestelse eller skade som falge av uautoriserte forandringer, eller for uriktig buk av maskinen.

Folgende sikkerhets punkter er brukt ut denne manualen. Gjor deg kjent med disse punktene og deres mening for

installasjon, service eller du utforer noen innstillinger pa denne maskinen

ADVARSEL /)\ Advarsel innebarer en risiko som kan fare til kvestelse eller dod. Ikke fortsett utover advarsien for den er ordentlig forstatt og mottiltak er igangsatt. FORSIKTIG (1) Forsiktig innebeerer en risiko som kan medfore skade pa maskinen. Ikke fortsett utover advarslen for den er ordentlig forstatt og mottiltak er igangsatt.

Vanlige sikkerhetstiltak.

Bruk bare denne maskinen etter 4 ha kontrollert at den er korrekt installert ifolge manualen.

Advarsel skiltene ma bestandig holdes i skikket stand og eventuelt byttes ut hvis det oppstar skade pa dem, slik at kunden uten vanskelighet kan lese dem.

Hvis det er en feil eller et problem med maskinen, ma den straks settes ut av funksjon. Og ma under ingen omstendigheter startes for problemet er rettet pa.

Installasjon, service, justering eller rutine vedlikehold skal bare utfores av kvalifiserte personer.

For fortsatt beskyttelse mot brann, forsikre deg at hoved sikringen bare byttes ut med en av samme type og verdi. Bruk av andre sikringer eller materiale er forbudt.

Stromforsyningen inne i monitoren vill vzere varm og ha omrader med hey spenning selv om maskinen har blitt slatt av. og det er muligheter for skader og elektriske sjokk. Vzer forsiktig sa du ikke berorer disse omradene.

For & forhindre mulige elektriske sjokk grunnet funksjonsfeil, ma denne maskinen vere ordentlig jordet.

Hvis ledningen til hoved stromforsyningen skades ma den straks bytes ut.

Ikke sla pa maskinen for den er korrekt installert.

For du kopler maskinen til stramnettet, forsikre deg om at maskinen innstilt for den korrekte spenningen og de riktige sikringene benyttes. OBBB B BB BP BBE

Page 19

MERKNADER VED INSTALLASJON

sla ALDRI pa maskinens stromforsyning for installasjonen er fullfort. {77 “yy

For a forhindre eventuelle elektriske sjokk, forsikre deg om at maskinen er koplet til et stromnett med ordentlig jording. 4 For a forhindre at kundene blir skadet av spillets bevegelige deler. Oo BP BPE

forsikre deg om at det er minst 500mm avstand mellom andre Se maskiner eller vegger. A © :

For a forhindre skade pa maskinen p.g.a. feil bruk, srg for at spenningen “Yo

til hoved stramforsyningen er 230Volt AC. bY “i

Si y oe

MERKNADER: Hvis plassen hvor spillet skal plasseres har polerte gulv Yh ; MERKNADER: For a fa adgang til stramforsyningen og CPU-kort, forsikre = SS©O S

anbefales det at du benytter gummi sko under niva justeringene, for a forhindre at maskinen kan flytte pa seg SENN

deg om at bakparten av hoved kabinettet er skilt fra vegger QA SX NYS

eller andre maskiner med minst 500mm.

Spillet har montert hjul for a gjore det letter 4 flytte pa. Hver forsiktig nar det skal flyttes pa en hellende overflate.

Hoved enheten i spillet har tyngdepunktet i fronten, sa det er viktig at minst 2 personer blir brukt til a montere eller flytte denne enheten.

Monterings posisjonen til hoved enheten er veldig hay, og det er viktig at denne hayden nas sikkert, uten at man ma strekke seg. Benytt deg av hjelpemiddel. (f.eks sto, krakk, gardintrapp osv)

Den totale hayden pa hoved enheten er 2310mm. veer forsiktig med hoye hindringer som f.eks lysror.

Nar spillet skal flyttes, forsikre deg om at spillet er delt i 3 deler: Topp enhet, Front enhet, Hoved enhe PB EP Be -

FJERNE OG UTSKIFTE ENHETER OG DELER.

Installasjon, service, justering eller rutine vedlikehold skal bare utfores av kvalifiserte personer.

Ikke lag noen forandringer pa denne maskinen uten godkjenning. Dette kan medfore uforutsette farer.

Bare deler spesifisert av Namco Europe Ltd. skal benyttes ved utskifting eller reparasjon av deler (dette gjelder ogsa skruer).

Forsikre deg om at strammen er slat av for du pabegynner noe som helst vedlikeholdsarbeid (feilsoking, reparasjon osv.)

Hvis du utforer arbeid som ikke er beskrevet i denne manualen, ta kontakt med din distributor for instruksjon da ikke noe ansvar vill bli akseptert for skade pa maskin eller pa personer.

Deler av stromforsyningen og monitoren er fortsatt varm eller bzrer hoye spenninger selv etter strammen er slat av og kan forsake skader eller elektriske sjokk. Forsikre deg om at du ikke berorer disse delene.

Forsikre deg om at maskinen er slatt av for du kopler sammen eller tar fra hverandre plugger eller koplinger. >BP BPP BP PBB

Nar du fjerner hoved koplingene fra maskinen, eller hoved pluggen fra stapselet, ta bestandig tak i pluggen og ikke ledningen.

Page 20

@D Niets uit deze publikatie mag worden gereproduceerd door enig mechanisch, fotografisch of electronisch proces, of in de vorm van een fonografische opname, noch mag het opgeslagen worden in een retrieval systeem, doorgezonden of anderszins gekopieerd voor publiek of privégebruik, zonder toestemming van Namco Europe Limited.

Ofschoon de informatie in deze handleiding in goed vertrouwen is gegeven en nauwkeurig was ten tijde van het drukken, houdt Namco zich het recht voor om veranderingen en aanpassingen te maken zonder bericht.

Deze machine is geproduceerd volgens Richtlijnen van de Europese Gemeenschap, en is getest en is in overeenstemming met de Richtliinen 89/336/EEC en 72/23/EEC door de toepassing van de standaards EN55014, EN55104 en EN60335-1 (zie voorin de handleiding) en draagt als zodanig het CE-merk. Enige veranderingen of aanpassingen aan deze machine dienen in overeenstemming te zijn met de Richtlijnen van de Europese Gemeenschap. Enige ongeauthoriseerde veranderingen aan dit produkt kunnen in strijd zijn met deze Richtlijnen.

Onder sommige omstandigheden van extreme externe storingen, bij. radiotransmissies, electrostatische ontladingen of pieken op het net, kan prestatieteruggang optreden. De machine zal echter normaal presteren zodra de storingsbron gestopt of verwijderd is.

Let op: - als de spelprocessor reset a.g.v. een onderbreking of vermindering van de netstroom, dan kunnen opgebouwde credits verloren gaan

Dit spel is niet een machine zoals omschreven in de Machinery Directive 89/392/EEC.

Veiligheidsopmerkingen Om deze machine veilig te kunnen gebruiken, dient védr installatie, aanpassing of gebruik van deze machine, de Bedieningshandleiding zorgvuldig gelezen te worden Telkens wanneer de eigenaar van deze machine de demontage, installatie, aanpassing of routine-onderhoud toevertrouwd aan een andere persoon, dient de eigenaar er voor te zorgen dat deze persoon de juiste voorzorgsmaatregelen en relevante gedeeltes uit de handleiding lest voordat hij begint Om er voor te zorgen dat geen ongelukken gebeuren als de machine gebruikt wordt, dienen onderstaande veiligheidsaanwijzingen Zorgvuldig opgevolgd te worden. Deze handleiding maakt samen met de installatiehandleiding (waar van toepassing) een integral deel uit van de apparatuur en moet te allen tijde ter beschikking staan van exploitatie- en onderhoudspersoneel. Deze machine is alleen bedoeld voor gebruik binnenshuis en dient alleen gebruikt te worden voor bedoelde doeleinden. Namco Ltd. is niet verantwoordelijk voor ongelukken, letsel of schade die voortkomt uit ongeoorloofde veranderingen aan of onjuist gebruik van deze machine

Veiligheidsopmerkingen

De volgende veiligheidsopmerkingen worden overal in deze handleiding gebruikt. Maak uzelf vertrouwd met deze opmerkingen en hun betekenis véér installatie, het plegen van onderhoud of het aanbrengen van aanpassingen aan deze machine.

WAARSCHUWING A Waarschuwing geeft een gevaar aan dat zou kunnen resulteren in letsel of de dood. Ga niet verder dan een waarschuwingsopmerking totdat de aangegeven omstandigheden volledig begrepen zijn en hieraan voldaan is.

VOORZICHTIG (7) _Voorzichtig geeft een gevaar aan dat zou kunnen resulteren in schade aan de machine. Ga niet verder dan een voorzichtigheidsopmerking totdat de aangegeven omstandigheden volledig begrepen zijn en hieraan voldaan is

Algemene veiligheidsoverwegingen

Stel deze machine alleen in gebruik nadat gecontroleerd is of de machine correct en overeenkomstig de handleiding is geinstalleerd.

De waarschuwingsstickers dienen altijd in goede staat te worden gehouden en vervangen indien versleten, zodat de klant ze goed kan lezen.

Als zich een fout of probleem voordoet met de machine, dan dient de machine onmiddellijk stopgezet en het probleem verholpen te worden voordat de machine verder gebruikt wordt.

Installatie, service, aanpassingen of routine-onderhoud dient alleen uitgevoerd te worden door hierin bekwame personen.

Om blijvende bescherming tegen brandgevaar te garanderen, dient ervoor gezorgd te worden dat de netzekeringen alleen vervangen worden door zekeringen van hetzelfde type en dezelfde sterkte. het gebruik van andere zekeringen of ander material is verboden.

De voeding in de monitor blijft warm en er kunnen componenten electrisch geladen blijven ondanks dat de mac! UlTgeschakeld is, waardoor er brandwonden of electrischee schokken kunnen worden opgelopen. Ben voorzic raak deze delen niet aan. gen

Om mogelijke electrische schokken a.g.v. storingen te voorkomen, MOET deze machine voorzien zijn van een goed vastzittende aardstekker.

Mocht het netsnoer op enig moment beschadigd worden, dan moet deze onmiddellijk vervangen worden.

Zet de machine niet AAN totdat deze correct is geinstalleerd.

Voordat de machine op het lichtnet wordt aangesloten, dient gecontroleerd te worden of de machine op het correcte voltage staat afgesteld en of de correcte zekeringen zijn aangebracht. OBB BP B BBB BB

Page 21

O Fe BBE

Ne OPMERKING: Als de machine op een gladde ondergrond wordt gebruikt,

KK < OPMERKING: Om toegang te krijgen tot de voeding- en de CPU- NS NX \

assemblies, dient ervoor gezorgd te worden dat de MA S WN

Opmerkingen aangaande Installatie

Sluit de machine nooit aan op de stroomtoevoer totdat de installatie is voltooid.

Om mogelijke electrische schokken te voorkomen, dient ervoor “yyy, gezorgd te worden dat de machine middels een goed vastzittende iy /

aardstekker op het lichtnet is aangesloten. yy Wy i)

Om ervoor te zorgen dat klanten niet gewond raken door de beweging van het spel, dient ervoor gezorgd te worden dat er Z minimaal 500mm ruimte is tussen andere machines of muren.

(Om schade aan de machine door verkeerd gebruik te voorkomen, dient Z YA

ervoor gezorgd te worden dat het voltage van het lichtnet 230volts AC Z J bedraagt. | Y ZA, 4 ie

is het raadzaam rubber matjes onder de stelpootjes te G idly,

bevestigen om te voorkomen dat de machine over de vioer— [% een YL, LoL. gaat glijden.

achterkant van het kabinet minimaal 500mm verwijderd is van de muur of andere machines.

PB BPP B- Het spel is voorzien van wieltjes, waardoor het gemakkelijker is om te verplaatsen. Wees voorzichtig als de machine op een hellend viak gereden wordt.

Het zwaartepunt van de Header Assembly ligt aan diens voorkant, waardoor het belangrijk is dat minimaal

2 personen de Header Assembly aanbrengen of vei

De Header Assembly moet op een hoge positie geplaatst worden en het is dus belangrijk dat deze hoogte veilig kan worden bereikt zonder veel te strekken. (bijv. middels een trap of een kruk)

De hoogte van het hoofdgedeelte is 2310mm: kijk dus uit voor obstakels zoals lampen.

Als de machine verplaatst of gedragen wordt, dient ervoor gezorgd te worden dat deze in 3 delen wordt afgebroken: Header Assembly, Front Assembly, Ride Assembly

> BP Be BP B&

> Ver deren en vervangen van Assemblies en onderdelen

Installatie, service, aanpassingen of routine-onderhoud dient alleen uitgevoerd te worden door hierin bekwame personen.

Maak geen veranderingen aan deze machine zonder goedkeuring vooraf. Dit kan onvoorzien gevaar opleveren.

Alleen onderdelen die door Namco Europe Ltd. zijn gespecificeerd dienen gebruikt te worden bij het vervangen of repareren van onderdelen (incl. schroeven).

Zorg ervoor dat de machine UlTgeschakeld is voordat er enig onderhoudswerk wordt verricht (troubleshooting, reparaties etc.)

Bij het verrichten van werkzaamheden die niet in deze handleiding staan beschreven, dient voor instructies altijd contact opgenomen te worden met de verdeler aangezien geen verantwoording wordt genomen voor schade of letsel.

Delen van de voeding en de monitor blijven warm of behouden hoogspanning zelfs nadat de machine UlTgeschakeld is en zouden verbrandingen of electrische schokken kunnen veroorzaken. Ben voorzichting en raak deze delen niet per ongeluk aan.

Zorg ervoor dat de machine is UlTgeschakeld voordat pluggen of connectors ingestoken of uitgetrokken worden.

Als het netsnoer uit de machine of uit het stopcontact verwijderd wordt, dient altijd de stekker vastgepakt te worden en niet het snoer. w

Page 22

®

Nenhuma parte desta publicacdo poder ser reproduzida por processos mecanograficos, fotograficos, electrénicos ou ainda sob a forma de gravacdo sonora nem t&o pouco podera ser gravada através de sistemas informaticos transmissiveis ou de outra forma copiados para uso publico ou privado sem autorizacdo expressa da NAMCO EUROPA LIMITADA.

A informagao contida neste manual foi fornecida de boa fé, sendo rigorosa na altura da sua publicagéo. A NAMCO EUROPA LIMITADA, reserva-se 0 direito de proceder a mudangas e alteracdes sem qualquer aviso prévio. Esta maquina foi fabricada de acordo com as Directivas Comunitarias Europeias e tem sido testada em conformidade com as seguintes Directivas: 89/336/EEC e 72/23/EEC através dos requerimentos normativos, EN55014, EN55104 e EN60335-1 (ver capa frontal do manual) e como tal sustenta o certificado de marca de CE. Quaisqueres alteragdes ou modificagdes efectuadas nesta maquina deverdo ser em conformidade com as Directivas da Comunidade Europeia. Quaisquer alteragdes nao autorizadas a este equipamento poderdo infrigir tais Directivas.

O funcionamento normal desta maquina, podera ser afectado debaixo de algumas condicées extremas de interferéncias externas tais como; transmissées via radio, descargas electroestaticas e passagens de corrente na rede de alimentacdo. Contudo o seu funcionamento normal sera restabelecido logo que a fonte de interferéncias tenha cessado ou tenha sido neutralizada.

Nota :- Se 0 processador de jogo for inicializado devido a uma interrup¢ao ou quebra da corrente principal, quaisqueres creditos obtidos poderao desaparecer.

Este jogo por si so nao contitui uma maquina tal como defenido pelas Directivas de Maquinaria de 89/392/EECS8.

AVISOS DE SEGURANCA Afim de usar esta maquina com seguranga, certifique-se que lé este manual de operador atentamente antes de proceder & montagem e afinacdo ou uso da mesma. Sempre que o proprietario desta maquina confiar a desmontagem, instalago, afinago ou manutengdo preventiva da mesma a outra pessoa, devera este assegurar - se que a pessoa em questao Ié as precaugdes apropriadas e capitulos relevantes deste manual antes de iniciar o trabalho. Afim de evitar qualquer tipo de acidente quando a maquina estiver em funcionamento, devera seguir rigorosamente os procedimentos de seguranga descritos abaixo Este manual juntamente com o manual de instalac4o (aonde aplicavel), contituem parte integrante do equipamento e deverao estar sempre disponiveis ao operador e pessoal tecnico de assisténcia Esta maquina destina-se a ser operada em espacos interiores apenas e a sua utilizag&o deve circunscrever-se somente aos fins previstos A Namco Ltd. declina qualquer responsabilidade por acidentes, ferimentos ou danos resultantes de modificagdes nao autorizadas ou uso indevido desta maquina

AVISOS DE SEGURANCA

Os seguintes avisos de seguranga s4o usados através de todo o manual. Familarize-se com cada um destes avisos e respectivos significados antes de instalar, assistir ou efectuar qualquer afinagdo nesta maquina.

PERIGO —/\_Perigo revela uma situagao anormal que podera resultar em ferimentos ou morte. Nao avance para além de um aviso de Perigo sem que todas as condi¢ées indicadas estejam completamente esclarecidas e resolvidas.

CAUTELA © Cautela revela uma situag4o anormal que podera resultar em danos materiais para a maquina. Nao avance para além de um aviso de Cautela sem que todas as condigées indicadas estejam completamente esclarecidas e resolvidas. (o Bae)

AVISOS DE PERIGO

Esta maquina sé devera ser colocada em funcionamento apés ter sido verificado que se encontra instalada correctamente e de acordo com o manual de instrugées.

Os avisos de perigo devem ser sempre mantidos em boas condicées de leitura de forma a permitir uma leitura clara por parte do utilizador, caso se encontrem danificados deverao ser substituidos.

Caso esta maquina manifeste algum erro ou problema durante o seu funcionamento, devera ser imediatamente parada até que o problema em questao seja rectificado.

A montagem, assisténcia e afinagdes ou manutengao de rotina desta maquina, deverao ser somente executadas por tecnicos ou pessoas devidamente qualificadas para o efeito. Afim de garantir uma protecdo anti - fogo permanente nesta maquina, certifique-se que os fusiveis de proteco sdo sempre substituidos por fusiveis de igual valor ou calibre aos de origem. O uso de outro tipo de fusiveis ou material é proibido.

A fonte de alimentagao do monitor encontrar-se-a quente, tendo zonas de alta voltagem, mesmo apés a maquina ter sido desligada. Deste facto podera resultar a ocurréncia de queimaduras ou choques electricos. Seja cuidadoso para evitar contacto com estas zonas. Esta maquina deve estar sempre equipada com uma ficha com circuito de protecgao a Terra, afim de evitar possiveis choques electricos, caso surga uma falha no sistema.

Se a qualquer altura o cabo de alimentagdo principal ficar danificado, devera ser imediatamente substituido. BPR EP B BBBB B&B

Nao ligar a maquina sem que esta tenha sido correctamente instalada.

@ Antes de ligar a maquina & tomada da rede de alimentagdo principal, certfique-se de que a maquina esta preparada para a voltagem correspondente e de que também se encontra protegida com os fusiveis apropriados.

Page 23

> BB)

)

NOTAS :

NOTAS :

NOTAS SOBRE A INSTALAGAO

NUNCA ligar a maquina sem que a instalagdo esteja completamente finalizada.

Afim de evitar possiveis choques electricos, certifique-se que a ysis

maquina esta ligada a rede de alimentacado com uma ficha protegida YY Yn —Yy

com circuito de terra. LL

Afim de evitar ferimentos pessoais nos clientes, provocados pelo movimento da maquina, certifique-se que existe pelo menos 500mm __—|“ de separagao entre outras maquinas ou paredes. A

Afim de evitar danos_na maquina causados por falhas de operacao,yyy
certifique-se que a voltagem da rede de alimentagdo principal 6 de“yjYo
230volt AC4Y

yz iy

Se esta maquina estiver colocada sobre um chao polido, recomenda-se Li iy

a utilizago de tapetes de borracha debaixo dos pés niveladores, afim Zz as g

de prevenir a maquina de deslizar no chao SX Ws

Quando precisar de aceder a fonte de alimentagdo e as placas (CPU), \\ Mu .

certifique-se que a parte trazeira do mével central esta separada da QL QQ OQ

parede ou de outras maquinas pelo menos 500mm afim de ganhar espago de manobra

> BBP B& Esta maquina esta equipada com rodas afim de facilitar a sua deslocagao tenha cuidado ao mover a maquina num plano inclinado.

O bloco Superior (Cabega) tem o centro de gravidade para a frente, porconseguinte é importante que pelo menos sejam utilizadas duas pessoas para montar ou desmontar este Bloco Superior.

A posicao do bloco superior quando montado na maquina é muito alta. Torna-se importante ter meios seguros de alcance, tais como; escadotes ou escadas afim de evitar riscos desnecessarios.

Aaltura total do bloco principal, 6 de 2310mm, tenha cuidado com qualquer tipo de obstrugées existentes em altura como por exemplo; calhas electricas ou candeiros.

Ao deslocar ou transportar a maquina, certifique-se que se encontra desmontada em 3 blocos: Bloco Superior, Bloco Frontal, Bloco da Cabine de Condugao ~\

SPP BP BBP BE SUBSTITUIGAO E MONTAGEM DE PEGAS

A montagem, assisténcia e afinagées ou manutengdo de rotina desta maquina, deverao ser somente executadas por tecnicos ou pessoas devidamente qualificadas para o efeito.

N&o faga qualquer tipo de alteracao prévia nesta maquina sem aprovaco prévia. Se tal acontecer podera provocar danos e perigos imprevisiveis.

A substituicdo ou reparacdo de pegas devera ser feita apenas com pecas de origem ou especificadas pela “Namco Europa Ltd.” (incluindo parafusos)

Certifique-se que a maquina se encontra desligada sempre que ini manutengao. (identifagao de avarias, reparagdo etc.) iar qualquer tipo de trabalho de

Caso esteja a efectuar um trabalho nao descrito neste manual, certifique-se que contacta o seu distribuidor para obter instrugées, caso contrario nao serdo aceites responsabilidades por danos causados ou ferimentos.

Algumas zonas da fonte de alimentagao e do monitor ficam quentes e transportam correntes de alta voltagem, mesmo depois de a maquina ter sido desligada, podendo causar queimaduras e choques electricos. Tome cuidado para nao tocar acidentalmente estas zonas.

Certifique-se que a maquina esta desligada antes de ligar ou desligar qualquer tipo de fichas ou jungées. Quando desligar a ficha principal da maquina ou a ficha do cabo de alimentacao das tomadas da parede, devera sempre agarrar na ficha e nunca puxar pelo cabo da mesma. w

Page 24

S Ingen del av denna publikation far reproduceras, varken fotografiskt, elektroniskt eller i nagon form av |judinspelning. Det far inte heller lagras i nagot atervinningssystem, dversandas eller pa annat satt kopieras for offentlig eller privat anvandning, utan tillstand fran NAMCO EUROPE LIMITED.

Eftersom informationen i denna manual lamnas ut i god tro och var korrekt nar den trycktes, reserverar sig NAMCO EUROPE LIMITED for andringar.

Denna maskin har tillverkats enligt direktiv fran europeiska unionen, ar testad och uppfyller direktiven enligt 89/336EEC och 72/23/EEC med tillampning av EN55014, EN55104 och EN60335-1 standard (se manualens framsida) och bar darmed ocksé CE-market. Varje forandring eller modifiering av denna maskin maste ske i éverens-stammelse med EU-direktiven. En forandring i denna produkt, som inte Ar auktoriserad, kan strida mot dessa direktiv.

Under vissa omstandigheter nar det galler extrema externa stérningar, t ex radiosandningar, elektrostatiska urladdningar eller natburna strémstémingar, kan resultera i en nagot nedsatt funktion. Maskinen kommer dock att aterga till normal funktion, sa shart stérningen har upphért eller avigsnats

OBS! Om spelprocessorn startar om till féljd av ett avbrott eller reducering av strémmen kan registrerade krediter ga forlorade.

Detta spel ar inte en maskin enligt definitionen i Maskindirektivet 89/392/EEC

SAKERHETS VARNING

For att maskinen ska kunna anvandas pa ett sakert satt, ska manualen lasas noggrant fére installation, anvandning eller justering

Om agaren till maskinen anfértror nagon annan person att montera isd, installera, justera maskinen eller utfora rutinunderhall, ska Agaren férsakra sig om att denna person laser om férsiktighetsatgarder och tillimpliga delar av denna manual innan arbetet pabérjas.

For att forhindra att nagon olycka hander nar maskinen r igang, maste sakerhetspunkterna beskrivna nedan foljas strikt.

Denna manual tillsammans med installationsmanualen (nar tillmpligt) utgér en integrerad del av utrustningen och maste vara standigt tillganglig for operatérer och service personal.

Maskinen ar avsedd fér inomhusbruk och ska endast anvandas for detta andamal.

Namco Ltd. bar inget ansvar for olyckor eller skador som orsakats av icke auktoriserade andringar i maskinen eller felaktigt anvandande av densamma.

SAKERHETSANVISNINGAR

Sakerhetsanvisningarna nedan anvands genomgaende i manualen. Gér dig fértrogen med varje anvisning och dess innebérd innan installation, service eller justeringar gérs pa denna maskin

VARNING A "Varning” anger en fara som skulle kunna skada eller fororsaka dédsfall. Fortsatt inte vid en sadan varningsanvising innan de pavisade férhallandena ar férstadda och atgardade i sin helhet.

OBSERVERA © “OBSERVERA’ anger en fara som skulle kunna fororsaka skada pa maskinen. Fortsatt inte vid en sadan varningsanvising innan de pavisade férhallandena ar férstadda och atgardade i sin helhet.

ALLMANNA SAKERHETSBEAKTANDEN

att inte igang maskinen utan att ha kontrollerat att den ar korrekt installerad och i 6verensstammelse med manualen.

Varningsanvisningarna maste alltid hallas i gott skick och ersattas nar de blir slitna, sa att kunderna kan lisa dem dem tydligt.

Om det uppstar fel eller problem med maskinen, maste anvandningen stoppas omedelbart och problemet rattas till innan den ater anvands.

Installation, service, justeringar eller rutinunderhall ska endast utféras av en fér andamalet kvalificerad person.

Fér kontinuerligt skydd mot brandfara, ska man férsakra sig om att huvudsakringarna endast ersatts med samma typ och specifikationer. Anvandandet av andra sakringar eller material ar forbjuden.

Strémférsérjningen inne i monitorn haller sig varm och har omraden med hég spanning, 4ven nar maskinen stangts av och det finns risk for brannskada eller elektriska stétar. Var férsiktig och vidrér aldrig sadana omraden.

For att férhindra en eventuell elektrisk st6t férorsakad av fel, MASTE maskinen vara férsedd med sakert ansluten JORDAD kontakt.

Om strémfdrsérjningskabeln pa nagot satt skadas, maste den bytas ut omedelbart.

Vrid inte strémbrytaren till ON innan maskinen ar korrekt installerad.

Innan strémmen sats pa till maskinen, maste man forsakra sig om att den ar installd pa ratt spanning och att rat sakringar ar isatta ObBP B BBB BB B&B

Page 25

Ob BE

Y OBSERVERA: Om maskinen ar placerad pa ett polerat golv, recommenderas YLLLLLEL 1 YY att placera gummibrickor under nivajusteringen for att Yjyugios forhindra att maskinen glider pa golvet SS RON S \ OBSERVERA: Fér att kunna komma at stromférs6rjningen och CPU, se till att WN \ ATT BEAKTA VID INSTALLATION Y

SAtt aldrig pa strémmen pa maskinen innan installationen r klar. Y tf §

LLLL: A Z For att férhindra elektriska chocker, forsakra dig om att maskinen kopplas till strémférsérjning med jordad kontakt Z Fér att undvika skador av spelets rdrelser, forsakra dig om att det Sv | finns ett avstand pa minst 500 mm till annan maskin eller vagg. Z Y 4 For att undvika skador pa maskinen p g a felaktigt handhavande, Oy forsakra dig om att stromstyrkan Ar 230 volt AC. YO

baksidan av huvudkabinettet ar placerat minst 500 mm fran WA \ vagg eller annan maskin. OK nv}

BB BB B Spelet ar férsett med hjul fér att underlatta forflyttningar. Var férsiktig om spelet ska flyttas pa en sluttande yta.

Toppskylten har tyngdpunkten framtill, darfér ar det viktigt att minst 2 personer satter dit eller tar bort den.

Toppskyltens placering ar mycket hégt upp och det ar viktigt att dana hjalpmedel anvands sa att man nar upp utan att stracka sig (t ex trappstege, pall osv).

Den totala héjden ar 2310 mm, tank pa eventuella hégt placerade hinder, t ex lampor.

Om spelet ska flyttas eller baras, kontrollera att spelet ar monterat isdr i 3 delar: Toppskylt, Monitorenhet, Spelkontrollenhet

> Bb BP BB

\ A ATT TA BORT ELLER BYTA UT ENHETER OCH DELAR >)

Justeringar och underhall pa denna maskin skall endast utféras av kvalificerad personal.

G6r inga andringar pa denna maskin utan ett godkannande i férvag. Detta kan férorsaka oférutsagbar fara.

Endast delar som 4r specificerade av Namco Europe Ltd. ska anvandas vid utbyten eller reparation av delar (inklusive skruvar).

Férsakra dig om att stro6mmen ar avstangd innan underhallsarbete pabérjas (felsékning, reparationer etc.)

Om arbete ska utféras som inte ar beskrivet i denna manual, ar det viktigt att kontakta aterférsaljaren fér instruktioner eftersom inget ansvar accepteras fér averkan eller personskador.

Delar av strémférsérjningen och monitorn ar varma och strémbarande 4ven efter str6mmen stangts av och kan orsaka brannskador eller elektriska stétar.

Férsakra dig om att maskinen ar avstangd innan kontakter satts i eller tas ur.

Nar kontakten tas ur maskinen eller ur vaggen, ta alltid tag i kontakten och inte i sladden. wv

Page 26

<>)

Tasta julkaisusta ei saa ottaa missaan muodossa kopioita yksityis- tai julkiseen kaytt6on ilman NAMCO EUROPE LIMITED:in lupaa.

Tassa ohjekirjassa olevat tiedot pitavat julkaisuhetkella paikkansa. NAMCO EUROPE LIMITED:illa on kuitenkin oikeus muutoksiin ilman erillista ilmoitusta

Tama laite on valmistettu EC direktiivien mukaisesti. Se on testattu ja todettu noudattavan seuraavia direktiiveja: 89/336/EEC ja 72/23/EEC (EN55014, EN55104 ja EN 60335-1 standardit). Nain ollen tama laite on varustettu CE-merkinnalla. Kaikki tahan laitteeseen kohdistetut muutokset on tehtava EC- direktiivien mukaisesti. Mika tahansa valtuuttamattoman huoltomiehen tekema muutos voi olla direktiivien vastainen

Laitteen toiminta voi hairiintya maardtyissa olosuhteissa, jotka johtuvat Aarimméisista ulkoisista sahkohairibista, kuten radiolahetys, elektrostaattinen purkaus tai vahvavirrasta syntynyt hairié. Toiminta normalisoituu kuitenkin heti, kun ulkoinen sahkéhairié on poistettu.

Huom:- Jos peliprosessori resetoituu sahkdkatkoksen tai vastaavan johdosta, voivat kaikki pelivaraukset havita

Tama laite ei ole 89/392/EEC direktiivien mukainen kone.

Turvallisuusvaroitus

Taman laitteen turvallinen kaytté edellyttaa kayttdohjekirjan huolellista lukemista ennen laitteen asennusta, sAatda tai kaytt6a.

Jos taman laitteen omistaja antaa jollekin toiselle osapuolelle tehtavaksi purkaa, asentaa, sataa tai muuten huoltaa laitetta, on omistajan varmistuttava siit, etté toinen osapuoli on lukenut ja ymmartanyt kayttdohjekirjan oleelliset osat ennen tyohon ryhtymista

Turvallisuusohjeita on seurattava tarkoin vahinkojen valttémiseksi laitteen ollessa kaytéssa .

Tama ohje seké mahdollinen asennusohje muodostavat laitteiston oleellisen osan ja on siksi aina oltava huolto- ja kayttohenkilékunnan kaytettavissa.

Tama laite on tarkoitettu vain sisatilakaytt66n. Sita ei saa kayttaa muihin tarkoituksiin.

Namco Ltd ei vastaa niist onnettomuuksista, loukaantumisista tai vahingoista, jotka johtuvat laitteeseen ilman Namco Ltd:n lupaa tehdyisté muutoksista laitteen vaarast kaytésta.

Turvallisuusohjeet

Tassa kaytt6ohjekirjassa on kaytetty seuraavia turvallisuuteen liittyvia huomautuksia. Tutustu jokaiseen naista. Ala asenna, huolla tai sda laitteistoa, ennen kuin olet taysin ymmartanyt mit ne tarkoittavat.

VAARA —//\_ “Vara” tarkoittaa uhkaa, joka voi johtaa loukkantumiseen tai kuolemaan, Ala koskaan ohita Vaaramerkintaa, ennenkuin ohjeissa esitetyt olosuhteet on ymmérretty taysin.

VAROITUS © “Varoitus” tarkoittaa uhkaa, joka voi johtaa laitteen vioittumiseen. Ala koskaan ohita Vaara-merkintaa,

YLEISET TURVALLISUUSNAKOKOHDAT

Varmista, eta laite on asennettu oikein ja ohjekirjan mukaisesti ennen kayttéénottoa.

Varoitustaulut on pidettava hyvassa kunnossa. Jos ne ovat kuluneet, ne on ehdottomasti vaihdettava, jotta asiakkaalla olisi mahdollisuus lukea niita selvasti.

Vain riittavan ammattipatevyyden omaava henkilé saa suorittaa asennus-, huolto-, saaté- tai muita laitteeseen kohdistuvia rutiinitoimenpiteita.

Jotta palovaaraa ei syntyisi, saa padsulakkeita vaihtaa vain samankokoisiin sulakkeisiin. Muiden sulakkeiden tai materiaalin kaytté on ehdottomasti kielletty.

Monitorin sisalla oleva virtalahde pysyy kuumana ja siina on alueita, joissa on korkeajannite vaikka laite on kytketty pois paalta. Palovammojen tai sahkdiskun saaminen on mahdollista. Ald koske naihin alueisiin.

seksi vikatapauksissa, laite on ehdottomasti kytkettvd maadoitetulla johdolla maadoitettuun pistorasiaan.

Vioittunut verkkojohto on valittémasti vaihdettava.

Ala kytke laitetta paalle, ennen kuin se on oikein asennettu. OPP BP BBB BP BBE

Varmista ennen verkkoon kytkemista, eta virtalahteen jannitteen asetus on asetettu oikealle jannitteelle ja ett siind on oikeat sulakkeet.

Page 27

Oo BB B&B

Huomio: Jos tama laite sijoitetaan liukkaalle esim. vahatulle lattialle,

Huomio: Varmista, etta takaosan taakse jaa vahintéaan 500 mm tilaa, jotta ASENNUSHUOMIOITA

suoritettu loppuun.

Ala koskaan kytke laitetta paalle ennen kuin asennus on , Yy ZZ,

Mii ; Taman laitteen virtalahde on kytkettava maadoitetulla johdolla maadoitettuun pistorasiaan, jotta sahkdiskun vaaraa ei olisi. gZ

Varmista, etta laitteen ja seinan tai toisen laitteen valissa on 44n 500 mm, jotta asiakkaat eivat loukkaannu laitteen

suositellaan laitettavaksi kumityynyt saatdjalkoihin liikkumisen estamiseksi.

virtalahteeseen ja CPU-korttiin paasee kasiksi.

SPB BB B&- ~\ Laite on varustettu kaantyvilla pyérilla. Tama on pidettéva mieless4, kun laitetta siirretéan kaltevalla alustalla.

Ylaosan painopiste on ylaosan etuosassa. Tasta syysta on ylaosaa asennettaessa tai poistettaessa oltava vahintaan kaksi henkiléa.

Ylaéosan asennusasento on erittain korkealla. On tarkedaa, etta tarvittavalle korkeudelle paastaan vaivattomasti ilman venyttamista. (esim. kayta tukevia tuoleja tai tikkaita)

Laitteen kokonaiskorkeus on yli 2310 mm. Varmista, ettei katossa ole esteita. esim. valaisimia.

Kun siirrat tai kannat laitetta varmista, eta laite on purettu neljaan osaan. Yldosa, koottu, Etuosa, koottu, Liikkuva ajo-osa, koottu

PB BP BBP BP B B&B Vain riittavan ammattipatevyyden omaava henkilé saa suorittaa asennus-, huolto-, saat laitteeseen kohdistuvia rutiinitoimenpiteita.

Talle laitteelle ei saa tehda mitdan hyvaksymattémia muutoksia. Se voi aiheuttaa ennalta-arvaamattomia vaaroja.

Vain Namco Europe Ltd:n maarittelemia varaosia saa kayttaa vaihtaessasi tai korjatessasi osia. (sisaltien ruuvit).

Varmista, etta laite on kytketty POIS PAALTA ennen tyén aloittamista.

Ota yhteytté maahantuojaan ohjeita varten, jos joudut tekemaan tyétehtavid, joita ei ole esitelty huoltokirjassa, muuten vastuuta vioista tai loukkaantumisista ei ole.

Virtalahde ja monitori pysyvat kuumina ja niissa on aluei kytketty pois , joissa on korkeajannite vaikka laite on . Palovammojen tai sahkdiskun saaminen on mahdollista. Ala koske ni

Varmista, etta laite on kytketty POIS PAALTA ennen johtojen kytkemista tai irrottamista.

Irrottaessasi verkkojohdon seinasta tai laitteesta, ota kiinni itse pistokkeesta, ei johdosta.

Page 28

aR WNS> Contents

SPECIFICATIONS . HOW TO PLAY MAJOR COMPONENTS ... MOVING THE MACHINE... wis INSTALLATION oo. cceececcececc cee cccececceceececeeceeseceececseseeseseeseeeseeesesssesenesessseeets 4

5-1 Fitting the Header Assembly ... 5-1 Fitting the Header Assembly ... 5-2 Adjusting the Level Adjusters 5-3 Fitting the Coin Tower : 5-4 Fitting the Pedal Assembly «00.00.0000... cccccscecec eee eeceseeeseceeeseeeeeeeceseeeeseteeeneereeseeereess 11 ADJUSTMENTS 6-1 Turning on the Power 6-2 Adjustment Switches . 6-3 Test Mode . 6-3-1 Coin Options 6-3-2 Game Options 6-3-3 V/O Test

6-3-3-1 I/O PCB Check

6-3-3-2 Gun Initialize

6-3-3-3 Switch Test..

6-3-3-4 Solenid Test

6-3-4 Monitor Test - 6-3-5 SOUN TeSt o.oo... cece cccescseecscsescessesessssseesssecssssscssssscesssscesssscesesseecesisisesieisesisisisititeseeeses 6-3-6 ADS Data

6-3-7 Others ... REMOVING AND REPLACING ASSEMBLIES AND PARTS 7-1 Replacing the Monitor 7-2 Replacing the Fluorescent Tube or Starter 0.0.0.0... cece eects eee ee teeseeeereneeeeteaes 7-3 Replacing the Pedal Switch 7-4 Greasing the Pedal Assy Plunger 7-5 Replacing the Pedal Plunger 74 Gun Assembly 7-6-1 Replacing the Gun ASSeMbly .......:.ccisse cose cscstecssecsscetaeseseesscusvasaegccesscanteecsvetsce ateeniecnass 31 7-6-2 Removing the Gun Slide . 7-6-3 Removing the Gun Cover 7-6-4 Replacing the Solenoid 7-6-4 Replacing the Solenoid ... 7-6-5 Replacing the Flexible Gun Conduit

SCHEMATICS

Page 29
  • SPECIFICATIONS

POWER SUPPLY:- 230volts / 300watts AC

AMBIENT OPERATING +5°C to +25°C TEMPERATURE:

MONITOR:- Hantarex 28” Polo (Auto Degauss)

COIN ACCEPTOR:- Mars CashFlow 4 Channel - Dispense

DIMENSIONS:- Assembled 1500(w) x 1510(d) x 2090(h)

Monitor Cabinet 1500(w) x 790(d) x 1730(h) Coin Tower 1100(w) x 720(d) x 1110(h) Header Assembly 1460(w) x 380(d) z 480(h) Pedal Assembly 250(w) x 250(d) x 160(h)

WEIGHT:- Assembled 279kg

Monitor Cabinet 205kg Coin Tower 42kg Header Assembly 24kg Pedal Assembly 4kg

ACCESSORIES:- Keys: (Cash Door)... (Coin Door).. (Back Door).

IEC Mains Lead «W000 ee 1

Operators Manual........0..00.0 1

Monitor Manual .........0. ee 1

CashFlow Documents .................. 1

Pedal ASSY ..........cceeeeeeeeeeees 2 Security Screw (M5x16).......0.0... 8

Hex Head Screw (M8x25) Flat Washer (M8) Spring Washer (MB) .............00.

M5 Security Wrench.. M6 Security Wrench..

Page 30
  • HOW TO PLAY

This is a gun shooting game where players press on a foot pedal to hide

behind an object to avoid an enemy attack, then release the pedal to get out from behind the object and attack the enemy.

HOW TO CONTROL

  • Step on the pedal = attack position. In this position you can shoot the enemy. You are also subject to an attack.
  • Release the pedal = defence position. In this position you are hidden behind an object and cannot be hit by the enemy. Releasing the pedal also reloads the gun.

MODES

  • Linked play mode: This mode is for two player co-operative play. If selected by a single player an additional player can join the game after it has started.
  • Solo play mode: This mode is for a single player only. No one can join the game once it has started.
  • Modes are selected on the Mode Selection Screen at the start of the game.

RULES

1. Every time you are hit by the enemy you lose a life. You also lose a life if

the time period for that scene reaches zero. the time period is restored at the start of a new life or when the scene has been completed. The game is over when all lives are lost.

  • Aplayer’s achievement is assessed by score at the end of the game. The higher the score, the higher the achievement.

Demonstration video clips between games can be skipped by aiming and shooting the gun at the screen.

Page 31
  • MAJOR COMPONENTS

Header Assy

Gun Assy

Coin Door

Monitor Cabinet

Coin Tower Pedal Assy

PSU Assy

Mains-In ON/OFF &

Game PCB Assy

Page 32
  • MOVING THE MACHINE

This machine is fitted with castors to make it easier to move. Take care when moving the machine on an inclined surface.

The overall height of the machine is 2090mm. Take care of any overhead obstructions. (e.g. Light Fittings, Electric Cables etc.)

When moving the game, ensure that the game is dis-assembled into 3 parts: Monitor Assembly, Coin Tower, and Header Assembly.

  • INSTALLATION

Notes on Installation

WARNING°«NEVER turn the power to the machine ON until

installation has been completed.

WARNING«In order to prevent possible electric shocks, be sure

that the machine is connected to the mains with a securely connected earthed plug.

WARNING«So that customers are not injured , ensure that there is

at least 500mm separation between other machines or walls.

CAUTION)+In order to avoid damage to the machine due to mis-

operation, ensure that the voltage of the mains supply is Ne 230volts AC. D)

NOTE . If the location site of this machine has a polished floor it is

recommended that rubber pads are fitted under the level adjusters to prevent the machine sliding on the floor.

. In order to gain access to the Power Supply and CPU assemblies, make sure that the rear of the machine is separated from a wall or other machine by at least 500mm.

. When installation is complete, it is imperative that the game is initialized. (See section 6-3-3-2 page 18)

Page 33

=

an >

=

a Pw

no

Pye

=

oP A

This machine is designed for INDOOR USE ONLY. Do not install in the following places.

Outdoors Direct Sunlight, places with excessive humidity or dust, places where there is water leakage, near air-conditioning or heating equipment, places with excessive heat or cold temperature. Places where it would be in the way of emergency exits or fire extinguishing equipment. Unstable places or places with excessive vibration. Places that are not level.

This machine must not be cleaned with a water jet, or installed in an area where a water jet could be used

where a water jet could be used.

DIESES GERAT IST NUR FUR DIE GEWERBLICHE AUFSTELLUNG IN GESCHLOSSENEN RAUMEN BESTIMMT. DAS GERAT DARF AN FOLGENDEN PLATZEN NICHT AUFGESTELLT WERDEN

Im Freien. In direktem Sonnenschein, an extrem feuchten und staubigen Platzen, an Platzen mit Wasseranschliissen und méglichen Leckagen, nahe Klima- und Heizungsanlagen, an Platzen mit extrem hohen oder niedrigen Temperaturen. In der Nahe von Notausgangen oder Feuerléschgeraten. An unstabilen Platzen oder Platzen mit ibermafBiger Vibration. An Platzen, die nicht eben sind.

DENNE MASKINE ER KUN DESIGNET TIL INDEND@RSBRUG INSTALLER IKKE MASKINEN PA FOLGENDE STEDER

Udenders Direkte sollys, steder med hoj fugtighed el. stov, steder med vand udslip, i nerheden af air-condition eller varme udstyr, steder med uszdvanlig hoj el. kold temperatur. Steder hvor den vil sta i vejen for nodudgange eller brandslukningsudstyr. Ustabile steder eller steder med for store vibrationer. Steder der ikke er plane.

ESTA MAQUINA ESTA DISENADA UNICAMENTE PARA USO EN INTERIORES. NO INSTALE LA MAQUINA EN LOS SIGUIENTES LUGARES.

Exteriores. Bajo luz solar directa, en lugares con polvo o humedad excesiva, lugares donde hay filtraciones de agua, cerca de aparatos de calefaccion o de aire acondicionado, lugares con temperatura ambiente muy alta o muy baja. Lugares donde la maquina obstruya salidas de emergencia 0 equipos de extincion de incendios. Suelos inestables o lugares con vibraciones excesivas. Lugares con suelos no nivelados.

Page 34

=

ey

ae

=

2 Pw A

CETTE MACHINE EST DESTINEE UNIQUEMENT A UN USAGE INTERIEUR NE PAS INSTALLER LA MACHINE DANS LES ENDROITS SUIVANTS

A Vextérieur. Directement exposée au soleil, aux endroits excessivement humides ou poussiéreux, aux endroits ou il y a des risques de fuite d’eau, prés de ventilateurs ou source de chaleur, aux endroits trés chauds ou froids. Dans des zones de proximité des sorties de secours ou d’accés aux équipements d’extinction du feu. Dans des emplacements instables ou soumis 4a de fortes vibrations. Dans des endroits dénivelés.

TO MHXANHMA EINAI ZXEAIAZMENO FIA XPHZH ZE EZQTEPIKO XQPO MONO MHN TONOOETHEETE TO MHXANHMA TOYS AKOAOYOOYS XOPOYE

E&wtepika Ameu@eiac oTov HAlo,o€ pep OTOU UTIaPXE! UYpacia f OKOVN,WEpN OTIOU umlapxel APBovo vepo,kovTa o¢ air-condition fh GAAou eidouc BEppavon,pEpn HE urepBoAiKh upNAH fH XaNA PeppoKpagia. Ze pépn Omou epModiZouv péEoa avayKngs 1.x. TUpOOBEOTHpEs | GAAa. Mn ota8epa pépn f NEP WE MOAAOUG KpadaopoUc. Mépn nou dev eivai enineda.

QUESTA MACCHINA E’ PROGETTATA PER ESSERE USATA ESCLUSIVAMENTE IN AMBIENTI INTERNI. NON INSTALLARE LA MACCHINA NEI SEGUENTI LUOGHI.

In ambienti esterni. Alla luce diretta del sole, in posti con eccesiva umidita 0 polvere, in luoghi dove ci siano infiltrazioni d’acqua, vicino ad apparecchi di condizionamento d’aria oppure riscaldamento, in posti eccessivamente caldi o freddi.

In luoghi dove potrebbe esserci un uscita di emergenza o un’attrezzatura per lo

spegnimento del fuoco. In posti non stabili o con eccessive vibrazioni. In luoghi non piani.

DENNE MASKINEN ER BARE KONSTRUERT FOR INNEND@RS BRUK IKKE INSTALLER MASKINEN PA F@LGENDE PLASSER.

Utendors Konstant sollys, plasser med mye fuktighet og stov, plasser hvor det er vannlekasje, nzre luft kjolere eller varme elementer, plasser med overdreven hoy eller lav temperatur. Plasser hvor det vill sta i veien for nodutganger eller brannslukking utstyr. Ustabile plasser eller plasser med overdreven vibrasjon. Plasser som ikke er i vater.

Page 35

A

QL) DEZE MACHINE IS ALLEEN VOOR GEBRUIK BINNENSHUIS ONTWORPEN

no

OPw

=

oP

®

=

oP

@)

=

a Pw INSTALLEER DE MACHINE NIET OP DE VOLGENDE PLAATSEN

Buiten In direct zonlicht, op plaatsen met een zeer hoge vochtigheidsgraad of met veel stof, op plaatsen waar een waterlek is, dichtbij airco’s of verwarmingsapparatuur, op plaatsen met een zeer hoge of koude temperatuur. Op plaatsen waar nooduitgangen of blusapparatuur worden geblokkeerd. Op onstabiele plaatsen of plaatsen waar grote trillingen voorkomen. Op plaatsen die niet viak zijn.

ESTA MAQUINA FOI CONCEBIDA PARA UTILIZAGAO EM ESPACOS INTERIORES APENAS NAO INSTALAR A MAQUINAS NOS SEGUINTES LOCAIS:-

Exteriores. “Luz solar directa, locais com humidade excessiva ou po, locais aonde existam fugas de agua perto de ar condicionados ou equipamentos calorificos e locais com temperaturas excessivamente quentes ou frias. Locais aonde ficaria colocada no caminho de saidas de emergéncia ou equipamentos extintores de fogo. Locais estruturalmente instaveis ou locais com vibragées excessivas. Locais nao nivelados.

DENNA MASKIN AR AVSEDD ENBART FOR INOMHUSBRUK INSTALLERA EJ MASKINEN PA FOLJANDE STALLEN

Utomhus | direkt solsken, platser med extremt hég luftfuktighet eller damm, platser dar det forekommer vattenlackage, nara luftkonditionering eller varmeelement, i extremt hég eller lag temperatur. Platser dar den skulle kunna vara i vagen fér nédutgangar och brandslackningsutrustning. Instabila stallen eller dar stark vibration forekommer. Platser med nivaskillnad.

TAMA LAITE ON SUUNNITELTU VAIN SISAKAYTTOON ALA ASENNA LAITETTA SEURAAVIIN PAIKKOIHIN:

Ulkotilaan Suoraan aurinkovaloon, kosteisiin tai pélyisiin paikkoihin, vesivuotopaikkojen laheisyyteen, ilmanvaihto- tai lammityslaitteen lahistélle tai paikkoihin, jossa on erittain kuumaa tai kylmaa. Varauloskaytavien, muiden pakoteiden tai tulensammutusvilineiden eteen. Epavakaisiin tai tariseviin paikkoihin. Kaltevalle alustalle.

Page 36

5-1 Fitting the Header Assembly

The Header Assembly has a forward centre of gravity, so it is important that at least two people are used to fit or remove the Header Assembly.

The fitting position of the Header Assembly is very high, and it is important that a means of reaching the height safely, without stretching, is available. (e.g. steps, step stool etc.)

  • Remove 2off pozi head screws (M5x12) and remove the connector cover.
  • Place the header on to the monitor cabinet and slide it forwards so that it engages under the fixing brackets at the front.

Header Assy

Pozi head screw (M5x12)

Pozi head screw (M6x30)

Connector cover

Am Slide forward

Retaining bracket Connector

  • Connect the connector, and refit the connector cover using the 2off pozi head screws (M5x12).
  • Retain the header in position with 3off pozi head screws (M6x30)
Page 37

5-2 Adjusting the Level Adjusters

  • When the monitor cabinet is in its final position, lower the four (4) level adjusters with a spanner so that the machine is level and all castors are raised from the floor by approx. 5mm. Tighten the lock nuts with a spanner to ensure that the level adjusters do not move.

Level Adjuster

Note: If the location site of this machine has a polished floor it is recommended that rubber pads are fitted under the level adjusters to prevent the machine sliding on the floor when in use.

5-3 Fitting the Coin Tower

  • Remove 4off security screw (M5x12) and remove the joint box top cover.

Security screw (M5x12)—_____,

Joint box cover plate

Joint box

  • Place the coin tower up to the joint box taking care not to trap any wires.
Page 38
  • Retain the coin tower to the joint box with 4off hex head screws (M8x20), flat and spring washers.

Hex head screw (M8x20) with Flat & Spring washers

Coin tower assy

Joint box

  • Connect the connectors and refit the joint box cover plate with 4 off security screw (M5x12).
  • Adjust the level adjusters on the coin tower so that the coin tower is stable and level with the monitor cabinet. (see section 5-2 page 9)
Page 39

5-4 Fitting the Pedal Assembly

  • Fit, finger tight only, the joint brackets to the coin tower leg with 4off security button head screw (M6x12).

Coin tower leg

Security button head screw (M6x12)

Security button head screw (M6x12) Joint bracket

  • Place the pedal assembly close to the coin tower leg and connect the connector.
  • Fit the pedal assembly inside the joint brackets, taking care not to trap any wires and fit, finger tight, the 4o0ff security button head screws (M5x12).

Security button head screw (M5x12)

Joint bracket Pedal Assy

  • Ensure that the pedal assembly is flat on the ground and tighten fully the 4off security button head screws (M6x12) and the 4off security button head screws (M5x12).

Security button head screw (M6x12)

Security button head screw (M5x12)

Page 40
  • ADJUSTMENTS (

®

® @6 086 0 ® ®@

©)

@ Adjustment or maintenance on this machine should be carried out by qualified personnel only.

Aufstellung, Service, Einstellung und Wartung dirfen nur von dafiir qualifiziertem Fachpersonal durchgefiihrt werden.

Justeringer eller vedligehold af denne maskine bor kun udfores af kvalificeret personale.

Los ajustes y el mantenimiento de esta maquina deben ser realizados solo por personal cualificado.

L’installation, le service, le reglage, ou la maintenance doivent étre effectués uniquement par les personnes qualifiées.

Metatponés fh emldiopOwoeic ota PNXavAata mpénel va yivovtal HOvo amlé efouciodoTHpEvaG AToUA.

Regolazioni e manutenzione su questa macchina devono essere fatti solo da personale specializzato.

Justering eller vedlikehold pa denne maskinen skall bare utfores av kvalifiserte personell.

Aanpassingen of onderhoud aan deze machine dient alleen uitgevoerd te worden door bekwaam personeel.

Afinagées ou manutengao nesta maquina, deverdo ser efectuadas somente por pessoal qualificado.

Justeringar och underhall pa denna maskin skall endast utféras av kvalificerad personal.

Tata laitetta saa s4ataa tai huoltaa vain siihen ammattipatevyyden omaava henkilékunta.

6-1 Turning on the Power

After the machine has been installed, turn ON the power. The power switch is located on the rear of the monitor cabinet.

Page 41

6-2 Adjustment Switches

The Adjustment switches are located inside the coin door.

1. Service Switch. Press this switch to obtain game credits without incrementing the play meter.

Test Switch Slide the test switch ON to enter test mode. Test mode allows testing and the changing of game settings. (Refer to section 6-3 "Test Mode" page 14)

Select Up/Down Switch This switch is used to select the test required when in the Test Mode.

Enter Switch This switch is used to enter a selected test and to change settings within a test.

COIN COUNTER o

(Coin Fuse) ° fe)

PLAYER 1 PLAYER 2

uP UP @| SELECT @| SELECT DOWN DOWN

SELECT SELECT

O“eoO“6
TESTSERVICETESTSERVICE
©t2)
Page 42

6-3 Test Mode

  • Open the coin door and slide the test switch “ON”. The “Menu Screen” will be displayed on the monitor.
  • Select the test required by using the select up/down switch. The colour of the selected test will change.
  • Activate the test by pressing the Enter switch. Select “EXIT” in each test to return to the “Menu Screen’.
  • After testing is completed, slide the test switch to the “OFF” position to return to normal game mode.

The Test Switch must always be in the “OFF” position for normal game mode.

MENU

COIN OPTIONS hee Used to set the price of play

GAME OPTIONS eect Used to set the game options

VO TEST (— hleceeteteeeseeeteeeeeee Used for testing switches & Gun

MONITOR TEST — hele Used for setting the monitor

SOUND TEST — heer Used for setting the volume

ADS DATA —haeeceeeteteteteteteteees Used to view bookkeeping

OTHERS ——— hleleetettetetereees Used for testing the PCB

LINK MALFUNCTION 1 2. 3.. (a) GAME DIFFICULTY L/R:NOT THE SAME (b) Do not appear when OK The internal battery’s dead

\ SELECT SW: CHOOSE ENTER SW: ENTER

  • Error message related to link play . A message appears if the link play is defective. The number displayed represents the type of error

. when 1 or 2 is displayed either the main PCB or memory PCB may be

defective. Contact your distributor. . If 3 is displayed, the software version on the left game PCB is different from that on the right game PCB. Contact your distributor.

  • Error message related to difficulty settings . A message appears if the difficulty settings of the left and right game PCBs are different. Enter GAME OPTIONS inthe test mode and set both PCBs the same.
  • Low battery display . A message appears if the Main PCB battery is faulty. Contact your distributor.
Page 43

6-3-1

1.

Coin Options

Select “COIN OPTIONS” on the menu screen to set the game cost and related settings. The following screen is displayed.

Use the Select Up/Down switch to choose the required item then press the Enter button.

Use the Up/Down switch to change the setting.

Press the Enter button after the changes have been made to return to the options.

Select “EXIT” and press the Enter button to return to the menu screen.

Note:- The price of play on this machine is set within the Cashflow Coin Mech. Ensure that the Game Cost is set to 1 Coin 1 Credit.

"a >) COIN OPTIONS

<DEFAULT IN GREEN>

GAME COST 1 COIN (S) 1 CREDIT CONTINUE COST 1 COIN (S) 1 CREDIT

FREE PLAY OFF aces .. (Cc)

EXIT

SELECT SW: CHOOSE ENTER SW: ENTER

\ J

ITEM DESCRIPTION FACTORY SET

  • Game Cost |Coins required for number of Credits ----- settable 1-9 1 Coin 1 Credit
  • Continue Coins required to continue settable 1-9 1 Coin 1 Credit
  • Free Play No coins required for credit ----- On (Yes) / Off (No) OFF
Page 44

6-3-2. Game Options

1. Select “GAME OPTIONS’ on the menu screen to set the game variables. The following screen is displayed.

  • Use the Select Up/Down switch to choose the required item then press the Enter button.
  • Use the Up/Down switch to change the setting.
  • Press the Enter button after the changes have been made to return to the options.
  • Select “EXIT” and press the Enter button to return to the menu screen.

(— >) GAME OPTIONS

<DEFAULT IN GREEN>

PLAYER'S LIFE4lett fences(a)
DIFFICULTYC (MEDIUM) ©...pee(b)
ATTRACT SOUNDONecettttetetteeefeeeeeeteeeeeee(c)
HI-SCORE INITNOcetttteeteefeteeeteeeeeee(d)

YES

EXIT

SELECT SW : CHOOSE ENTER SW: ENTER Ne J

ITEM DESCRIPTION FACTORY SET

(a) Player's LifeNumber of lives at game start ---- settable 1 - 94

A (Very Easy) B (Easy)

  • Difficulty C (Medium) C (Medium) D (Hard) E (Very Hard)
(c) Attract SoundSound in attract mode ON /OFFON
(d) Hi-Score Init?Hi-Score initialized at power up YES/NONO
NOTE: The game will not function correctly unless the difficulty setting is the same for both players.
Page 45

6-3-3 I/O Test

  • Select “I/O TEST” on the menu screen to switches and lamps. The following screen is displayed.
  • Use the Select Up/Down switch to choose the required item then press the Enter button to enter the test.
  • Select “EXIT” and press the Enter button to return to the menu screen.

( > VO TEST DIP 4 = 12345678 [ON:OFF] —oeseeseecsesetesseteeesfeeesesteeeeeeeee (a) LINK ON 2 litettttteies feces (b)

1/0 PCB CHECK

GUN INITIALIZE

SWITCH TEST

SOLENOID TEST —eeeceececttesteteteetefeeteeeeeeeeee (f)

EXIT

SELECT SW : CHOOSE ENTER SW: ENTER Ne

  • Shows the condition of the DIP Switches on the PCB. In normal operation all switches are OFF. (If a switch is ON, it will be displayed in red.)
  • Checks that both game PCBs are communicating.

If the communication is good LINK ON 2 will be displayed

If link data is wrong LINK OFF will be displayed. If unrecognisable data is being received LINK NG will be displayed.

  • Checks function of I/O PCB.

Used to test and initialize the gun operation (see Section 6-3-3-2 page 18)

Selecting this item allows all switches and pedal sensor to be checked. (See 6-3-3-3 page 20)

Selecting this item allows the testing of the gun recoil solenoid. (See 6-3-3-4 page 21)

Page 46

6-3-3-1 I/O PCB Check

Al. Select ‘I/O PCB CHECK’ from the I/O Test Screen. Th screen is displayed:e following

a VO TEST

12345678 [ON:RED] ON 2 DIP 4 LINK

1/0 PCB CHECK

Master TX 3536 NAMCO LTD.

Time Crisis 2 ; Ver1.00 ; JPN

1/0 PCB Connect OK namco ltd.

TSS-1/O;Ver2.02;JPN;GUN-EXTENSION

EXIT

SELECT SW : CHOOSE ENTER SW: ENTER ~

6-3-3-2 Gun Initialize

  • Select ‘GUN INITIALIZE’ from the I/O Test Screen. T! screen is displayed:-

Va GUN INITIALIZE ~\

GUN INITIALIZE

GUN INITIALIZE

EXIT

SELECT SW : CHOOSE

Ne (CRT)

(PROJECTOR)

ENTER SW: ENTER he following

  • Use the Up/Down switch to select ‘GUN INITIALIZE (CRT)’, and press the Enter switch. The following screen is displayed.
Page 47

GUN INITIALIZE (CRT)

+

SHOOT AT SCREEN

TO CHECK GUN ACCURACY

PUSH ENTER SW : ADJUST GUN SIGHT

UP SELECT SW + ENTER SW: EXIT

Aim the gun at the screen and pull the trigger. A white spot will appear. If the spot appears where you aimed, the gun initialization is O.K. If the spot is not where you aimed, press the Enter button to initialize the gun. The following screen will be displayed.

(— >)

a

AIM AT CENTER OF THE CROSS

AND PULL GUN TRIGGER XN w,

Aim the gun at the centre of the cross and pull the trigger.

Slide the test switch OFF to return to normal game mode.

Enter test mode and select ‘GUN INITIALIZE’ from the I/O test screen and check the gun initialization. Repeat initialization if necessary

Page 48

6-3-3-3 Switch Test

  • Select “Switch Test” on the I/O menu screen to test the switches. The following screen is displayed.
  • The display shows the current state of the switches.
  • Press the Up Select switch and the Enter switch together to EXIT and return to the I/O menu screen

( SWITCH TEST >)

DIP 4 123456787 [ON/OFF] LINK ON 2

SWITCH TEST COIN SERVICE TEST UP SELECT DOWN SELECT ENTER TRIGGER FOOT PEDAL

UP SELECT SW + ENTER SW : EXIT NG /

  • Not Used
  • The display will change from OFF to ON as each switch is operated.
  • The game will return to normal play mode if this switch is turned off.

(d to h) The display will change from OFF to ON as each switch is operated.

Page 49

6-3-3-4 Solenid Test

  • Select “solenoid Test” on the I/O menu screen to test the switches. The following screen is displayed.

(— > VO TEST

DIP 4 12345678 [ON:RED] LINK ON2

SOLENOID TEST

PULL GUN TRIGGER TO ACTION

EXIT

SELECT SW : CHOOSE ENTER SW: ENTER NX 7

  • The gun recoil solenoid will operate each time the trigger is pressed.
  • Select ‘EXIT’ and press the Enter button to return to the I/O menu

screen.

Page 50

6-3-4 Monitor Test

  • Select “MONITOR TEST” on the menu screen to test and adjust the Monitor. The following screen is displayed.
  • Use the Select Up/Down switch to choose the required item then press

the Enter button. To return to the Monitor Test Menu from a test pattern

press the Enter button.

  • Select “EXIT” and press the Enter button to return to the menu screen.

MONITOR TEST

GRADATION PATTERN CROSSHATCH PATTERN (CRT) CROSSHATCH PATTERN (PROJ) WHITE WINDOW (H) WHITE WINDOW (M) WHITE WINDOW (L) INTERLACE PATTERN VIEW ANGLE ADJUST (CRT) VIEW ANGLE ADJUST (PROJ) FULL WHITE EXIT

SELECT SW: CHOOSE ENTER SW: ENTER Ne

Note:

Items (c) and (i) are not used on this game.

Page 51

6-3-5 Sound Test

1.

(a)

(b)

(c,)

(d) Select “I/O TEST” on the menu screen to switches and lamps. The following screen is displayed.

Use the Select Up/Down switch to choose the required item then press the Enter button.

Use the Up/Down switch to change the setting.

Press the Enter button after the changes have been made to return to the options.

Select “EXIT” and press the Enter button to return to the menu screen.

Va SOUND TEST <DEFAULT IN GREEN>

VOLUME FRONTLSP (0~64) 40... FRONT RSP (0~64) 40...

EXIT

SELECT SW: CHOOSE ENTER SW: ENTER Ne SERVICE SW : REQUEST ON/OFF REQUEST SONG NO. 000 oo

MESSAGE a eetetettttetteteeeeeeee ~

Volume setting for left channel speaker. Settable from 0 ~ 64 with 0 quietest and 64 loudest.

Volume setting for right channel speaker. Settable from 0 ~ 64 with 0 quietest and 64 loudest.

Each number will produce a different sound each time the Service button is pressed. (for a maximum of ten seconds) 001 when selected will produce a sound from the left speaker only, then the right speaker only and then both speakers together as a stereo check. The message field shows which speaker is active.

Displays the song No. details.

Page 52

6-3-6 ADS Data

By selecting ADS Data from the menu screen, all of the bookkeeping details can be read and/or reset.

6-3-7 Others

Select “OTHERS” on the menu screen. The following screen is displayed.

  • Use the Select Up/Down switch choose the required item then press the Enter button.
  • Select “EXIT” and press the Enter button to return to the menu screen.

( OTHERS »)

ROM1 Ver.97/07/07MON21:15:59=f (a)
ROM2 Ver.97/06/27FRI20:11:35
CLOCK97/08/27WED—.23:14:12ofc (b)

PCB TEST (——aceeetttetttttettttetetsteseees LANGUAGE ENGLISH... BACKUP MEMORY INITIALIZE NO. YES EXIT

SELECT SW: CHOOSE ENTER SW: ENTER Ne /

(a,) Displays game software version.

  • Allows the internal clock and calendar to be set.
  • Used to test the PCB. (this function is only for factory testing)
  • Sets the language displayed on the screen:

English : ENG

German : GER French : FRA Spanish : SPA Portugese : POR Italian : ITA

  • When selected the Data Initialization Menu appears. To reset all game settings to factory setting and clear all stored data , select YES from the Data Initialization menu then press the Enter button.
NOTE: The game will not function correctly unless the software version is the same for both players.
Page 53
  • REMOVING AND REPLACING ASSEMBLIES AND PARTS

7-1 Replacing the Monitor

The monitor is heavy. At least two people are required to remove the monitor.

  • Remove the 2off upper security screw (M5x12) and slacken the 2off lower security screw (M5x12), and remove the monitor rear access panel.
  • Remove the pozi head screw (M4x10) and remove the Earth wire and connectors from the monitor.

Security screw (MSx12) | {] \ SS nnn ; nnn Lh

Rear access panel p> Par

Pozi head screw (M4x10)

  • Remove 8off security screw (M5x16) and remove the monitor vac-form.

Security Screw (M5x16)

Monitor vac-form

Page 54
  • Remove 4off pozi head screws (M6x25), with flat washer (1”x%”), and remove the monitor by tilting the forward and lifting it out.

Flat washer 1x"

Pozi head screw (M6x25)

Monitor

Note: Take care not to knock the neck of the monitor tube when handling the monitor as it can be easily damged and the tube destroyed.
Page 55

7-2 Replacing the Fluorescent Tube or Starter

  • Remove 4off security screw (M5x12) and remove the top retaining bracket and header acrylic.
  • Replace the fluorescent tube or starter.
  • Refit the header acrylic and top retaining bracket.

Fluorescent tube Security screw (M5x12)

Starter Top retaining bracket

Header acrylic

Page 56

7-3 Replacing the Pedal Switch

  • Remove 4off security screw (M5x12) and remove the switch cover plate.

‘Security screw (M5x12)

Switch cover plate

  • Remove 2off pozi head screw (M3x16) and remove the switch. When replacing the switch, ensure that the wires are fitted to the correct terminals.
  • Slacken the 2off whizztite nuts (M4) and adjust the microswitch bracket so that the switch plunger operates the switch correctly without bending the switch lever against the switch body.
  • Refit the switch cover plate and 4off security screw (M5x12).
Page 57

7-4 Greasing the Pedal Assy Plunger

  • Remove 4off security screw (M5x12) and remove the switch cover plate.

‘Security screw (M5x12)

Switch cover plate

  • Remove 2off whizztite nuts (M4) and remove the switch.
  • Remove 4off whizztite nuts (M4) and remove the plaunger assembly.
Note: The plunger is spring loaded. Keep the plunger pressed in when removing the assy and release the plunger slowly.
  • Remove any old grease and dirt from the plunger and pedal plate.
  • Grease both the plate and spherical portion of the plunger.

Microswitch — Holder

7 Plunger Whizztite nut (M4) Lo r—_| Whizztite nut (M4)

Grease here

  • Reassemble in reverse order.
Page 58

7-5 Replacing the Pedal Plunger

1.

2.

4. Remove the plunger assembly. (See 7-4 page 29)

Pull the plunger out of the holder. Replace with the new plunger. (The new plunger should have grease applied all over prior to fitting).

Holder

Plunger ler a

Plate

Grease here

Reassemble in reverse order.

Page 59

7-6 Gun Assembly

7-6-1. Replacing the Gun Assembly

  • Remove 8off security screws (M8x20) and remove the gun pod complete with the gun.

‘Security screw (M8x20)

  • Disconnect the connectors and remove the 2off whizztite nuts (M6).

Whizztite nut (M6)

Connectors

Whizztite nut (M6)

Fixing plate

  • Remove the gun assembly from the gun pod.
Note: When replacing the gun assembly ensure that the earth wires are located on to the studs before fitting and tightening the whizztite nuts (M6)
Page 60

7-6-2. Removing the Gun Slide

  • Remove 4off cap screws (M3x10), 1off button screw (M4x25), and 1off hex nut (M4), and detach the gun slides (L) and (R).
  • Reassemble in reverse order.

Gun slide (L) Button bolt (M4 x 10) Gun slide (R)

Cap bolt (M3 x 10) Hexagon box nut (M4) Cap bolt (M3 x 10)

Page 61

7-6-3 Removing the Gun Cover

  • Remove the gun slides (L) and (R). (See 7-6-2 page 32)
  • Place the gun (L) face down, and remove the 4off button screws (M4x10), 1off button screw (M4x25), 4off hex nuts (M4), and 1off cap screw (M3x10). Remove the gun cover (R) taking care that the lens

Button bolt Gun cover (FR) (M4 x 25) / Cap bolt (M3 x 10)

Button bolt (M4 x 10)

Lens

Hexagon box nut (M4) er ene i os ee ee

does not fall out.

  • Reassemble in reverse order. (Ensure that the flat face of the lens is facing the back of the gun).

Ensure that the flat face of the lens is toward

isla the back of the gun

Page 62

7-6-4 Replacing the Solenoid

1._Remove the gun cover and gun slide (R). (See 7-6-2 page 32 and 7-6-3 page 33)

  • Disconnect the solenoid connector.
  • Remove 1off cap screw (M3x10) on the gun cover (L) and remove the solenoid bracket.
  • Remove 1off cup screw M (M3x8) and detach the earth wire.
  • Loosen the nuts (16mm dia.) and remove the solenoid.
  • Remove 2off cup screws M (M4x6) and detach the slide guide.
  • Pull out the solenoid plunger, taking care not to lose the spring.

Cup screw (M) Spring Plunger (M4x6) »~--—---~-~~---~~-~~~~_ ‘Cap bolt (M3 x 10) Solenoid

Nut (16mm in ee a | nominal diameter) : Solenoid

Ground wire bracket 4 Cup screw (M)(M3x8) — Toothed Slide guide

washer

  • Reassemble in reverse order.
Note: When reassembling match the D-type hole of the solenoid bracket to the D shape of the solenoid and ensure that the ‘E’ ring and spacers are in the correct positions.

Spacers Slide guide Solenoid \ =

Harness outlet (it must Solenoid bracket face downwards) Plunger —_ E-type snap rings

Page 63

7-6-4 Replacing the Tigger Switch

  • Remove the gun cover and gun slide (R). (See 7-6-2 page 32 and 7-6-3 page 33)
  • Replace the microswitch. Take care when replacing the switch that the correct wires are fitted to the correct terminals.
  • Reassemble in reverse order.

Microswitch Connect the black harness. Connect the blue hamess.

7-6-5 Replacing the Flexible Gun Conduit.

  • Remove the gun assembly. (See 7-6-1- page 30).
  • Remove the 2off security screws (M4x10), then detach the connector cover.
  • Remove the gun cover and gun slide (R). (See 7-6-2 page 32 and 7-6-3 page 33).
  • Detach the solenoid bracket and detach the solenoid connectors and earth wire. (see 7-6-4 page 34).
  • Disconnect the sensor and detach the fast-on connectors from the micro switch.
  • Remove the button head screw (M4x10) fixing the conduit to the gun cover (L) and detach the conduit.
  • Reassemble in reverse order.

Fast-on terminal (microswitch) Ground wire _-— Security screw (Maxt iS Connector (solencid)

Connector cover

Gun cover (R) Gun cover (L)

Flexible conduit

Page 64
  • PARTS

® | | 7 a || @®@

EL ue

: S

Page 65

Item Description Part No

4|Header Fixing Bracket46000836
5Monitor Vac-Form (LHS)46000834

For games with Serial Nos. 43887~43966 inc. Use Part No. XTC2-VACFORM-LHS

6{Monitor Vac-Form (RHS)46000835

For games with Serial Nos. 43887~43966 inc. Use Part No. XTC2-VACFORM-RHS

7|Monitor - Hantarex 28" Polo w/o Remote84000026

For games with Serial Nos. 43887~43966 inc. Use Part No. 84000001

8|Bass Loudspeaker - Time Crisis2 - Pioneer SWM 1034X006-115
9|Bass Port Tube46000837

For games with Serial Nos. 43887~43966 inc. Use Part No. XTC2-BASSTUBE

10|Sub Bass speaker Grille46000828
12|Adjustable Fooy - M16x9588300079
13|Swivel Castor - 75MM59000005
15|Monitor Rear Access Door46000831
17|Fork Here Decal40000072
18|Schaffner Mains-In Filter Assy62500010

Schaffner Boot 66000017

19|Interlock Switch60000006
20|Interlock Switch Cover39000028
21|Fuse 20mm 1A Q/B63500421
22|Fuse 20mm 500mA Q/B63500608
23|Monitor Vac-Form Top Decal40000174
24|Player One Decal40000180
25|Player Two Decal40000199
26|Vac-Form Decal A40000167
27|Vac-Form Decal B40000166
28|Cabinet Side Decal (LHS)40000143
29|Cabinet Side Decal (RHS)40000145
30|Cabinet / Gun Join Bracket Top Cover46000833
31|Join Bracket Reinforcing Bracket46000830
32|Cabinet / Gun Joint Bracket46000829
Page 66

lO)

Item Description Part No.

1|Header Cabinet37100089
2|Header Acrylic Closing Bracket - Top/Bottom46000840
3.|Header Acrylic30000023
4|Fluorescent Tube - 4'64500039
5|Fluorescent Assembly - 4'64000045
6|Header Speaker Grille46000841
7|Header Rear connector Cover46000842
8|Loudspeaker 4%" 20watt62000006
9|Header Decal - LHS40000020
10|Header Decal - RHS40000215
Page 67

Item Description Part No

1|Switchmode Power Supply - 5v @ 32A83000008
2|3v3 7A Converter83000003
3|Amplifier PCB AssyXTC2-AMPCB
4|Bridge Rectifier71000040
5|Fuse 1%" 2A Q/B63500504
6|Capacitor 22,000uF 25v70200043
7|Fuse1%" 500mA Slo-Blo63500637
8|Transformer 18v @ 3A67700015
9Game PCB AssemblyXTC2-PCB

For games with Serial Nos. 43887~43966 inc. Use Part No. XTC2-1P-PCB

10 |Fan 4%" 230v 67000015

11|Finger Guard39000169

12 |Fan Gasket 46000724

Page 68

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 69

Item Description Part No

1Coin Tower Top Vac-Form46000850
5|Swivel Castor - 40mm59000003
6|Coin Tower Underside Cover46000849
7Pedal Mounting Bracket - End46000854
8Pedal Mounting Bracket - Centre46000852
10|Gun Station Support Rail46000847
12|Rotary Moulded Gun Station - Blue46000844
14|Strain Relief Rope45000708
15|Play Instruction Decal - A40000252
16|Rotary Moulded Gun Station - Red46000845
17|Relief Rope Gun Hoop45000210

Gun Assembly - Blue XPB-Gun-Blue

18Gun Assembly - RedXPB-Gun-Red
21|I/O PCB AssyXTC2-IOPCB

22 | Adjustable Foot - M16x95 88300079

Page 70

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 71

Item Description Part No Gun Assembly - Red XPB-Gun-Red Gun Assembly -Blue XPB-Gun-Blue Gun Cover (LHS) - Red XPB-Cover-LR

'Gun Cover (LHS) - BlueXPB-Cover -LB
2{Trigger SpringXPB-296-421
5Trigger - RedXPB-Trigger-R

Trigger - Blue XPB-Trigger-B

4Solenoid - ST-O860A2XPB-004-056
5|Tube Bracket (A)XPB-296-418
6|Gun Cord Harness AssyXPB-296-401
7|Tube Bracket (B)XPB-296-423
8|Connector CoverXPB-296-424
9Gun Cover (RHS) - RedXPB-Cover-RR

Gun Cover (RHS) - Blue XPB-Cover RB Gun Slide (RHS) - Red XPB-Slide-RR

ieGun Slide (RHS) - BlueXPB-Slide RB
11|Slide RailE20+F15R2/60LXPB-296-425
12|E-type Snap Ring 7CR-3 (10dia)XPB-Eclip
13|SpacerXPB-296-422
14|Slide GuideXPB-296-417
18Gun Slide (LHS) - RedXPB-Slide-LR

Gun Slide (LHS) - Blue XPB-Slide -LB

16|Back SpringXPB-296-420
17.{Lens NA-V1472050XPB-296-426
18|Sensor PCBXPB-296-467
19|Microswitch SS-01GI2TXPB-000-228
20{Solenoid BracketXPB-296-416
21.|Silencer RubberXPB-296-428
Page 72

Item Description Part No.

4|Spring (A)XTC-631-221
5|Spring CoverXTC-631-218
7|Rubber StopperXTC-631-217
8|PlungerXTC-631-219
10|Spring (B)XTC-631-222
12|Microswitch - KSL 13XTC-000-027
Page 73

Item Description Part No

1 |3.5~6v Panel Mount Meter 65000002

20mm Panel Mount Fuseholder 63500786 ? Fuse 20mm 2A Q/B 63500501

SPDT Toggle Switch -(momentary action) 60000010

Pushbutton Switch 7mm - Red 60000059

Miniature Slide Switch 60000023

Page 74

©)

  • ii VERTER PCB

soa

On =: ——

Page 75

=

sence enscxer

i - = is: rs IT = LH = mi = =

§ | = a ——— Tr | tv? ——: _ | = = ioe SONASSY | sey =.

L

Page 76

Copies of Namco Game Manuals can be downloaded from our website: www.namco.co.uk under Components Distribution

For all Parts or Technical Support contact:

Brent Electronic, Namco House, Units 5-8, Acton Park Estate, The Vale,

London. W3 7QE

www.namco.co.uk

For Technical Support, Warranty and

Advance Replacement Parts:- J +44 (0) 20 8324 6120

For Consumable Parts:- J +44 (0) 20 8324 6102

Fax for both:- fy +44 (0) 20 8324 6126