CATHODE RAY TOMES

Food Fight CO-229-03 1st Printing

Food Fight (rev 3) (General Computer Corporation (Atari license), 1982) · Change Order · 18 pages · 11 sections · original scan

Page 1

Ist printing

Operators Manual (TM-229)

This Supplement contains Food Fight cocktail game information and is intended to be used with the upright game manual (TM-229). The specifi ¢ portions of TM-229 affected by the addition of the cocktail game information are referenced in this Supplement. The portions of TM-229 NOT mentioned herein apply to the cocktail game unless stated otherwise in the game manual. All major parts of the cocktail game are illustrated in Figure 1-2A with figure references to the applicable illustrated parts lists in this supplement and in TM-229,

ATART (© A Wemer Communcatons Company

Page 2

Table of Contents

1 Set-Up Procedures Opening the Cocktail Cabinet . Cocktail TableLegs ...........0s.s-cs sss seveeeees eeeeennen

3 Illustrated Parts Lists

Figure 3-2A Figure 3-3A Figure 3-8A Figure 3-94 Cabinet-Mounted Assemblies ........ 2.60.00. e eee eee Control Panel & Start Switch Assembly . Video Display Assembly............. : Utility Panel Assembly ..-.. 0.0.66... eee eee eee

List of Illustrations

Figure 1-24 Figure 1-2B Figure 3-2A Figure 3-3A Figure 3-84 Figure 3-94 Adjusting the Table Legs . . Cabinet-Mounted Assemblies ......... Control Panel & Start Switch Assembly . Video Display Assembly .... . oe . Utility Panel Assembly ..... 0.0.0.0 eee

Page 3

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 4

Set-Up Procedures

ae

Opening the Cocktail

Cabinet

Opening the Table Top

To open the cocktail game cabinet, unlock the two key locks located immediately below the table top (see Figure 1-2A).

  • Carefully lift the table top until the support arm locks into place. Do not jam the table top at the end ofits upward swing.

Opening the Access Panel

Lift out the steel security bar that secures the panel to the cabinet wall (see Figure 1-2).

  • Theaccess panel near the bottom of the cabinet will then come out.

enane the Table Top Stand opposite the hinged end of the cocktail cabinet and grasp the table top with your right hand.

  • With your left hand, hold down the button at the middle of the support arm and push the center of the support arm down.
  • Gently lower the table top to the closed position.
  • Lock both key locks.

Chapter 1

Page 5

CO-229-03,

Electromagnetic as Interference Cage S ry ee See Figure 3-12 } Electromagnetic | Interference Shield PCB See Figure 3-12 & 3-13 Video Display * Game PCB x See Figure 3-84* /| See Figure 3-12, 3-14 and | this Supplement Volume Control (To increase, = turn clockwise)

Auxiliary Self-Test

Coin Switch Switch

Utillty Panel See Figure 3-94*

Power Supply * See Figure 3-16 and this Supplement

Regulator/Audlo Il PCB See Figure 3-15,

Control Panel See Figure 3-3A*

Gimbal See Figure 3-4 | Coin Acceptors See Figure 3-10

Power On/Off Switch (under cabinet) Coin Counter See Figure 3-9 Adjustable Legs x Item with a serial number label See Figure 3-2A* *|llustrated parts lists included in this Supplement

Figure 1-2A Game Overview—Cocktail Game

Page 6

BH

Cocktail Table Legs

This cocktail cabinet may be adjusted to tour heights—65, 70, 76, or 101 cm (25%, 27%, 30, or 39% inches). Adjust the table height as follows: 1, Remove orempty the coin box to prevent loose coins from sliding out of the box and into the game cabinet.

  • Lay the table on end as shown in Figure 1-2B. Place a support (the coin box, books, or tool box) under the recessed side of the cabinet.
  • Remove the two Allen-head screws on each leg.
  • Grasp the legs and slide them into the desired position. Then replace the screws.
CAUTION To ensure cabinet strength, you must use two. screws to attach each table leg. Using only one screw may damage the cabinet wall when moving the cabinet across the floor. oN Add the following to Table 1-1 Installation Specifications:

Cocktail Game 62% x 82%cm(24% x 32% in.) 65 to 101 cm (25% to 39% in.) Space Required Game Height

Add to Figure 1-3:

NOTE The cocktail game also uses the 7A, 250 V fuse F1

Shipping Position (252, in.)

Figure 1-2B Adjusting the Table Legs

Page 7

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 8
Scan of page 8

This page is a drawing, shown as the original scan.

Page 9

035852-01 (Corner bracket) 82-406 fonead) (Eyebott) 038365-02 (Tabie top) ee 040333-01 (Bezel) 035851-01 (Hinge)

178015-001 036773-01 (Support) (Grille)

037686-01 037791-01 b (Grille) (Security bar)

e

(Backplate) .

A038375-01 So (Access panel)

@ @

037833-02 (Bracket)

A037672-01 (Power supply) 037243-01 i? 178034-024 (Base plate) (Fmolding) A,

78-3206 (Leveling leg)

78-3205 (Endcap) Video Display

Game PCB

A040052-01 (Main harness) EMI Cage

EMI Shield PCE

040075-01 (Lock and key assembly)

71-3201 (Anchor washer)

‘A040311-01 (Cabinet assembly)

040321-01 (Display mounting bracket)

178034-025 (Folding)

A037246-01 (Leg assembly)

A037292-01 (Leg support assy.)

037335-01 (Leg brace)

Figure 3-2A Cabinet-Mounted Assemblies CocktailGame A040310-01 A+

Page 10

78-6900401 78-6900402 (Tape) (Tape)

178034-026 (Tmoiding) 035867-02 (Display overlay)

A038384-01 (Start switch bracket assy.) See Figure 3-34 040332-01 (Glass shield wigraphics)

Gimbai Joystick Regulator/Audio II PCB

Control Panel Utility Panel

A005133-01 000869-01

(Fan—optional) (Speaker grille) 48-004 . ry (Speaker) (Fan grille), N . ~

A037886-01 (Power cord)

036773-01 (Base grille (Power harness)

009992-01 (Oniotf switch cover)|

A037470-01 (Power switch/plate (Retaining bracket)

assembly)

Coin Acceptor

A036775-01 (Coin box) A002465-01 (Coin counter)

Figure 3-2A Cabinet-Mounted Assemblies, continued Cocktail Game A040310-01 A+

Page 11

Cabinet-Mounted Assemblies Cocktail Game Parts List

Part No. Description A002465-01 Coin Counter Assembly A005133-01 Cooling Fan (optional equipment) A036775-01- Coin Box Assembly A037246-01 Leg Assembly (includes leg, 2 leveling legs, and 2 endcaps)

A037292-01Leg Support Assembly(includes 2 panel nuts and endcap)

A037470-01 Power On/Off Switch and Mounting Plate Assembly

A037886-01Strain-Relief Power Cord(U.S.)

A038375-01 Access Panei Assembly A040052-01 Main Harness Assembly A040054-01 Power Harness Assembly A040311-01 Cabinet Assembly The following four items are technical information supplements to this game: SP-229 Food Fight Schematic Package ST-229-62 Food Fight Cocktail Label with Self-Test Procedures and Option Switch Settings TM-187 Service Manual for 14-Inch Electrohome Color Raster Display (use with part no. 92-056) ™-229 .Food Fight Operators Manual with Illustrated Parts Lists 48-004 8 Q, 5 W, 5-Inch Round High-Fidelity Speaker (not shown) 62-039 Momentary-Contact SPDT Light-Emitting Diode Start Switch with Red Cap 71-3201 Anchor Washer for Table-Top Lock 78-3205 Endcap for Leg Assembly

78-3206Cabinet-Leveling Leg(not shown)

78-6900401 Vinyl Foam Single-Coated Adhesive Tape, %-Inch Wide x 4%.-Inch Thick (not shown—apply 126 inches under silkscreened border of table top) 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, %-Inch Wide x %-Inch Thick (not shown—apply two 6-inch strips under overlay border) 82-406 #%-20 x 2-Inch Eyebolt with %-Inch Threads 000869-01 Speaker Grille 009992-01 On/Off Switch Cover

034536-02Foam Pad(two required—place under Regulator/Audio II PCB)

034536-03 + Foam Pad (two required) 035851-01 Table Top Hinge (two required) 035852-01 Corner Bracket (four required) 035867-02 Smoke-Color Acrylic Display Overlay

036764-01Hook-Type Cam for Lock(not shown)

036773-01 Cabinet Base Grille 036774-01 Upper End-Panel Grille 036895-01 Black Molded Switch Bezel

037243-01Power Supply Base Plate(not shown)

037335-01 Leg Brace

037686-01Slip-In Cabinet Grille(located above control panels)

037753-01 Coin Acceptor Retaining Bracket (not shown)

037768-01Fan Grille(used as vent grille if no fan is included)

037791-01 Security Bar 037827-01 Backplate for Attaching Leg

Page 12

Cabinet-Mounted Assemblies Cocktail Game Parts List, continued

Part No. Description

037833-02 Security Bar Bracket 038365-02 Table Top 038385-01 Start Switch Mounting Bracket 040075-01 Lock and Key Assembly (two required)

040321-01 Display Mounting Bracket 040332-01 Tempered-Glass Shield with Graphics 040333-01 Display Bezel 178015-001 Hinged Table-Top Support

178028-002 End Cap for Upright Leg Support (not shown) 17803 4-024 ¥%-Inch Black Plastic T-Molding 178034-025 ?%,2-Inch Black Plastic T-Molding 178034-026 1%6-Inch Black Plastic T-Molding

Page 13
WARNING Players may receive an electrical - HORIZONTAL, shock if this control panel is not pro- A040409-01 POTENTIOMETER (Harness) WIRE COLORS perly grounded! After servicing any parts on the panel, make sure that Red the ground wire js firmly attached to the metal tab on theinside ofthe con- Violet trol panel. Black

VERTICAL POTENTIOMETER WIRE COLORS

A040314-01 (Control panel widecal)

040320-01 (Controt panel)

040331-03 (Decal—not shown)

'160013-001 (Leaf switch and button holder)

7555168 / (Orange pushbutton) g NOTE The 1-and 2-player start switches are mounted on the cocktail game cabinet. See Figure 3-2A for start switch BLACK assembly location. (Common). BLACK RED (+). (Common)

RED (+) WHITE/ORANGE (Normally open) WHITE/BLACK

WHITE/RED WHITEBROWN (Normally open) 038385-01 036895-01 (Bracket) (Switch bezel) 62-039 (Start switch) . Figure 3-3A Control Panel and Start Switch Assembly CocktailGame A040313-01 A and A038384-01 A

Page 14

Part No.

A038838-02 A040314-01 A040409-01 040320-01

040313-01 040331-03 160013-001 177010-244

178030-002 75-015S 75-5516B 75-9910NO Control Panel Assembly Cocktail Game Parts List

Description

Gimbal Joystick Assembly Control Panel with Decal Control Panel Harness Assembly Control Panel

Control Panel Assembly Control Panel Decal (not shown) Leaf Switch and Button Holder (leaf switch only is part no. 160012-001) #%-20 Hex Locknut

Orange Pushbutton Assembly #% Steel Flat Washer #%-20 x Inch Black Carriage Bolt #%-11 Stamped Nut

i

Page 15

92-056 (Video display)

Figure 3-8A Video Display Assembly — CocktailGame A040315-01 A A040414-01 (Harness)

Parts List

Part No. Description

A00315-01 14-Inch Color Video Display Assembly A04014-01 Display Harness Assembly 92-056 14-Inch Electrohome Color Raster-Scan Video Display 040333-01 Display Bezel (not shown) 040321-01 Display Mounting Bracket

Page 16

178070-001 (Volume control knob}

037685-01 (Bracket)

62-041 (Auxiliary coin switch)

(Common) BROWN 69-001 (Normaily open) (Self-test switch)

BLACK/YELLOW

19-9032 (Volume control)

Figure 3-9A Utility Panel Assembly CocktailGame A037866-01 A

Parts List

Part No, Description 03 7865-01 Uuility Panel Bracket 19-9032 Volume Control 62-041 SPDT Momentry-Contact Pushbutton Auxiliary Coin Switch with Black Cap 69-001 DPDT SelfTest Switch 72-68088, 8-32 x %-Inch Cross Recessed Pan-Head Screw (not shown} 75-9910W0 146-32 Stamped Nut (not shown) 178070-001 Volume Control Knob

Page 17
NOTE The Cocktail Game PCB Assembly number is A039945-41 A.

iN Change the Food Fight Game Printed-Circuit Board Assembly Parts List as follows:

  • Delete capacitor C60

© Add the following statement to the descriptions for Integrated Circuits 8K/L and a ene substitute is part no. 137289-002)

© Change part no. for Integrated Circuit 9K/L from 137289-004 to 137289-001.

© Delete resistor R58.

© Add the following part numbers after the Erasable Programmable Read-Only Memories list of parts:

DesignatorDescriptionPart No.
8CErasable Programmable Read-Only Memory136020-113
8DErasable Programmable Read-Only Memory136020-115
8EErasable Programmable Read-Only Memory136020-117

8F Erasable Programmable Read-Only Memory + 136020-119

9CErasable Programmable Read-Only Memory136020-114
9DErasable Programmable Read-Only Memory136020-116
9EErasable Programmable Read-Only Memory136020-118
oFErasable Programmable Read-Only Memory136020-120

oN Add the following to Figure 3-16:

© The Cocktail Game Power Supply number is A037672-01_ D.

© Add Transformer Assembly number A035888-03 callout to Figure 3-16.

Page 18

lem, call TELEHELP® at the Atari Customer Service office in your geographical area, as shown below.

Atari, Inc. ’ California Customer Service Office 1105 N, Fair Oaks Avenue i P. O. Box 427, Sunnyvale, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Pacific Time) POW From California, Alaska, or Hawaii ‘© (408) 745-2900 = Service from anywhere in the area shown in white toll-free (800) 538-1611

Service only

Atari, Inc. New Jersey Customer Service Office * 12A World’s Fair Drive, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) = From New Jersey (201) 469-5993 From anywhere else in this area @ oltre (800) 526-3849

EUROPE Parts and Service

Atari Ireland Limited European Customer Service Office Tipperary Town, Ireland . Telex 28-165 TIPPERARY TOWN, (Monday-Friday, 9:00-6:00 pm GMT) IRELAND BH 0602-52155