CATHODE RAY TOMES

Hoop It Up 3 on 3 TM-403 1st Printing

Hoop It Up 3 on 3 (Atari Games, 1995) · Technical Manual · 44 pages · 53 sections · original scan

Page 1

TIME WARNER x INTERACTIVE

—, x

GAMES

Page 2

ea ee

Page 3

TIME WARNER INTERACTIVE l"

® Hoop It Up is the registered trademark of Streetball Sports Ventures Partners. Licensed to Atari Games Corporation/Time Warner Interactive.

Page 4

InrRopucTION ¢ Hoop It Up Operator's MANUAL

COPYRIGHT NOTICE

Copyright © 1995 by Atari Games Corporation/Time Warner Interactive. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for substantial penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infring- _ing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 per infringing transaction in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of corporations.

Atari Games Corporation/Time Warner Interactive will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of games made by us. Anyone who purchases such copies risks forfeiting such a game. Published by: Atari Games Corporation/Time Warner Interactive 675 Sycamore Drive Milpitas, California 95035 Printed in the U.S.A. 7/95 Produced by the Time Warner Interactive Technical Publications Department. Design, Writing and Editing: Andrea Dencker Technical Illustrations: John Pastrikas and Maylan Wong NOTICE REGARDING

NON-TWI ParRtTs

WARNING Use of non-TWi parts or modifications of any Time Warner Interactive game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following:

  • Substitute non-Time Warner Interactive (TWi) parts in the game.
  • Modify or alter any circuits in the game by using kits or parts not supplied by Time Warner Interactive.

FCC COMPLIANCE

This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from a Time Warner Interactive game at your location, check the following: ¢ All ground wires in the game are properly connected as shown in the game wiring diagram.

  • The power cord is properly plugged into a grounded three-wire outlet.
  • On games provided with an Electromagnetic Interference (EMI) ground plane, be sure that the game printed-circuit boards (PCBs) are properly installed on the EMI ground plane and that the end board is securely installed with alll screws in place and tightened. If you are still unable to solve the interference problem, please contact Customer Service at Time Warner Interactive, See the inside front cover of this manual for service in your area. Trad

Preddvardd

ee el

Page 5

Hoop It Up Oprrator's Manual % INTRODUCTION

SAFETY SUMMARY

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found in this manual whenever they apply.

WARNING

Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded threewire outlet. If you have only a two-wire outlet, we recommend you hire a licensed electrician to install a three-wire grounded outlet. AC Power Connection. Before you plug in the game, be sure that the game’s power supply can accept the AC line voltage in your location. The line voltage requirements are listed in Chapter 1 of this manual. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power before removing or repairing any part of the game. Use Only Time Warner Interactive (TWi) Parts. To maintain the safety of your TWi game, use only TWi parts when you repair it. Using non-TWi parts or modifying the game circuitry may be dangerous, and could injure you and your players. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.

CAUTION Properly Attach All Connectors. Make sure that the connectors on each printed circuit board (PCB) are properly plugged in. The connectors are keyed to fit only one way. If they do not slip on easily, do not force them. If you reverse a connector, it may damage your game and void your warranty. Ensure the Proper AC Line Frequency. Games manufactured for operation on 60 Hz line power (used in. the United States) must not be operated in countries with 50 Hz line power (used in Europe). If a 60 Hz machine operates on 50 Hz line power, the fluorescent line ballast transformer will overheat and cause a potential fire hazard. Check the product identification label on your machine for the line frequency required.

ABOUT NOTES, CAUTIONS, AND

WARNINGS

In TWi publications, notes, cautions and warnings have the following meaning:

NOTE — A highlighted piece of information.
CAUTION — Equipment and/or parts can be damaged or destroyed if instructions are not followed. You will void the warranty on TWi printed-circuit boards and parts thereon, if equipment or parts are damaged or destroyed due to failure of following instructions. ‘WARNING — Players and/or technicians can be killed or injured if instructions are not followed.

Précautions de’Emploi Générales

tit

Page 6

INTRODUCTION % Hoop IT Up Operator's MANUAL

PRECAUTIO MPLOI GENERALES

Les précautions d'emploi ci-dessous s’adressent & toutes les personnes susceptibles d'utiliser ou de réparer ce jeu. La présente notice renferme également d'autres mises en garde et avertissements spécifiques.

MISES EN GARDE Mettez le jeu 4 la terre. Les joueurs risquent de recevoir une décharge électrique si le jeu n’est pas correctement mis 4 la terre! Pour éviter les décharges électriques, assurez-vous que le jeu est correctement mis 4 la terre avant de le brancher. Branchez-le uniquement dans une prise tripolaire avec mise 4 la terre. Si vous n’avez pas de prise tipolaire, il est recommandé de faire appel 4 un électricien breveté pour en installer une. Si la console de commande n’est pas correctement mise 4 la terre, les joueurs risquent de recevoir une décharge électrique! Si une réparation quelconque a été faite sur la console de commande, assurez-vous que le fil de mise 4 la terre est solidement attaché 4 l’intérieur de la console, Ceci fait, verrouillez le jeu. Branchement sur secteur. Avant de brancher le jeu, assurez-vous que son bloc d’alimentation est compatible avec la tension secteur locale. Les conditions d’alimentation du jeu apparaissent au premier chapitre de la présente notice. Débranchez le jeu du secteur avant toute réparation. Pour éviter Jes décharges électriques, débranchez le jeu du secteur avant de le démonter ou de le réparer. Utilisez uniquement des piéces TWi. Pour éviter les risques d’accidents, utilisez toujours des piéces TWi pour réparer le jeu. Vemploi de piéces d'autres marques ou la modification des circuits du jeu sont potentiellement dangereux pour le réparateur et pour les joueurs. Utilisez les fusibles appropriés. Pour éviter les décharges électriques, remplacez les fusibles par ceux indiqués dans la nomenclature du jeu. Les fusibles de rechange doivent étre du méme type, de la méme tension et de la méme intensité que ceux d’origine.

oz ATTENTION Attachez correctement tous les connecteurs. Assurezvous que tous les connecteurs sont bien enfichés dans les cartes circuits. Ces connecteurs sont dotés d’un détrompeur qui évite les erreurs de branchement. S’ils s’enfichent difficilement, ne forcez pas. Si vous branchez un connecteur a lenvers, vous risquez d’endommager le jeu et d’en annuler la garantie. Vérifiez la fréquence de ligne du courant secteur. Les jeux fabriqués pour fonctionner a une fréquence de ligne de 60 Hz (fréquence utilisée en Amérique du Nord) ne doivent pas étre utilisés dans les pays dont le courant a une fréquence de 50 Hz (Europe). Si vous branchez un appareil congu pour une fréquence de 60 Hz sur un courant d'une fréquence de 50 Hz, le transformateur ballast de ’éclairage fluorescent surchauffera, ce qui présente des risques d’incendie. Vérifiez la fréquence de ligne requise par votre machine; elle est indiquée sur sa plaque signalétique.

REMARQUES, AVERTISSEMENTS

ET MISES EN GARDE

Dans les publications d’TWi, les conventions, en ce qui concerne les remarques, avertissements et mises en garde, sont les suivantes: REMARQUE — Sert 8 attirer l’attention sur un point particulier. AVERTISSEMENT — Le non-respect des directives présente des risques d’endommagement et/ou de destruction pour le matériel et/ou les piéces. En cas d’endommagement ou de destruction du matériel ou des piéces, résultant du non-respect des directives, la garantie offerte sur les cartes circuits TWi et les pieces connexes TWi sera annulée, MISE EN GARDE — Le non-respect des directives présente des risques de blessures ou d’accidents mortels pour les joueurs et/ou les réparateurs.

Page 7

Hoop IT Up Operator's MANUAL @ INTRODUCTION

CONTENTS

1 Set-Up How to Use This Manual .. 1-1 Operating the Game .. . 1-2 Installation........ 12 Install the Playfield Balls . seveees 12 Load the Ticket Dispensers . 1-2 Level the Game... 6.6 eee Change the Bonus Tickets Sign coy Special Precautions . . Inspecting the Game . . Controls and Switch Locations . . Power On/Off Switch and Main Fuse ‘Ticket Dispensers .......... ons Liquid-Crystal Display and Keypad. vnc eee Adjust Contrast of LCD. Volume Control. ......-

Coin Counter. Setting the Coin, Ticket and Game Options Game Play... 0... 1 eee eee eee eee Introduction .... Game Play Hints .......... Game Play........-..6.0- Advanced Game Mode. .........60 000005

2 ‘Test Functions

Introduction... 6... eee eee eee 2-1 Using the Liquid-Crystal Display on the Game PCB. . 2-2 Attract-Mode (Accounting) Functions Program Modes .......-.--.00005 Set Parameters Mode . Set Cost $/Game .... Test Functions ... Display Memory... 06... eee eee

  • =Troubleshooting & Maintenance

Introduction. Maintenance Procedures.............+- Introduction... 2.6.0.6... cece eee Cleaning Procedure for Coin Mechanisms. . Cleaning Procedure for Ticket Dispensers. Cleaning Procedure for Ball Shooter. . . Troubleshooting Procedures......... Repair Procedures Introduction Ball Shooter Spring and Piston... .... Replacing the Ball Shooter Motor or Optics. Ball Shooter Right/Left Tilt Adjustment . . . . Basketball Control................-- Speaker. . . Attraction Panel Fluorescent Light Playfield Incandescent Lights... . . Backboard and Playfield Components, . System Logic Assemblies ................ 3

4 Parts Illustrations

Part Ordering Information ............00.005 4A For figure and page numbers, see the list of illustrations that follows.

5 Wiring Diagrams Introduction. . 6... 6. eee 5-1 For figure and page numbers, see the list of illustrations that follows.

Warranty Inside back cover

Page 8

Inrropuction # Hoop Ir Up Operator’s MANUAL

ILLUSTRATIONS

Figure 1-1 Operator Controls on Hoop It Up Game PCB ... woe 14

Figure 2-1 Detailed View of Keypad......... 2-2

Figure 3-1 —_ Ball Shooter Adjustment ....... . 34

Figure 4-1 Cabinet-Mounted Assemblies, Front View ...... 200.000.0005 42 Figure 4-2 Cabinet-Mounted Assemblies, Rear View se 43 Figure 4-3 Backboard Assembly............ 4-4 Figure 4-4 Control Panel Assembly.......... 45 Figure 4-5 Bellows (Basketball) Control Assembly .......- veces. 46 Figure 4-6 Ball Shooter Assembly... ........ 47 Figure 4-7. Over/Under Coin Door Assembly... 4-8 Figure 4-8 — Power Supply Assembly ......... 4-10 Figure 5-1 Figure 5-2 Hoop It Up Game Wiring Diagram . . 5-2 Score Board PCB Schematic

NOTE: The Hoop It Up Game PCB schematic diagram is not published in this manual. However, it is available free of charge by calling or writing to Time Warner Interactive Customer Service. See the inside front cover for our address and telephone numbers.

TABLES

Table 1-1 Game Specifications ............ 1-3

Table 2-1 Summary of Accounting Functions. .. 2-2 Table 2-2 Summary of Recommended Settings for All Parameters........ 23

Table 3-1 General Troubleshooting. ........ 3-2

Page 9

How To Use Tus MANUAL

|. HIS MANUAL IS written for operators

and service personnel. It provides in-

formation for setting up, playing,

testing, and maintaining your Hoop It Up*

game.

Hoop It Up is a two-player basketball re-

demption game featuring real basketball con-

trols that shoot air-activated balls into minia-

ture hoops and nets.

Chapter 1 of this manual contains set-up

and game play information. @ Chapter 2 con-

tains a description of the test functions and

option settings. The test modes are important

in the Hoop It Up game. Using the tests, you

can troubleshoot the large light-emitting diode

(LED) score displays, the game printed-cir-

cuit board, and the controls. You should CHAPTER 1

Set-Up

regularly do these tests to keep your game in

peak condition and at top earnings. ¢ Chapter

3 contains a troubleshooting table, plus main-

tenance and repair procedures for the game

components. If you have problems with your

game, use this chapter to troubleshoot and re-

pair it. @ Chapter 4 contains the illustrations

and Score Board PCB parts list. @ Chapter 5

contains the game wiring diagram and the

Score Board PCB schematic dia-

gram. Copies of the game PCB

schematic are available free of

charge by contacting our Cus-

tomer Service Dept.: see the

inside front cover of this

manual for the address

and telephone numbers.

Page 10

Cuarrer 1—Ser-Ur % Hoop IT Up Operator’s MANUAL

Operating the Game

To operate your game for maximum income, you should regularly use the self-test to check the electronics, controls and sound. By using the seif-test regularly, you can find and fix problems immediately. This lets you keep your game in top condition.

Installation

Hoop It Up is shipped almost completely ready to install. Only three steps need to be taken before turning on the power.

NOTE Do not change the angles of the top hoops. They are correctly installed when they tilt slightly up in the front (downwards towards the rear backboard). This angle helps players earn triples more easily.

Install the Playfield Balls

Unlock and remove the upper rear access door. Remove the three wood screws at the top of the backboard door and swing it open. Open the two packages of small balls. Put no more than 6 bails on each side of the playfield, on or near the ball shooter, Loading more than 6 balls will cause the ball shooter to jam up, and players will not be able to aim the balls correctly at the hoops. You should have at least 5 balls on each side of the playfield.

NOTE We recommend using only high-quality balls, which will be less likely to crack. Such balls have no visible seams. These balls should be readily available in toy stores. If you cannot easily find these balls, call Customer Service for sources. In an emergency you can use white table tennis balls, which are the same size and weight.

Load the Ticket Dispensers

Load the ticket dispensers with a supply of tickets. Refer to the Deltronic Labs ticket dispenser manual for instructions on this procedure. Level the Game

One of the keys to a properly working Hoop It Up game is making sure that it is level, especially on the right/left axis. Even if the game tilts slightly to the right or left, players will have a difficult time making baskets. Mounted inside the bottom of the game is a circular bubble level, which indicates if the game is not level in any direction. When you have moved the game to its location, open the lower rear access panel, and check the level. If the bubble is not in the center of the outlined circle, adjust the four adjustable glides until it is.

Change the Bonus Tickets Sign

(Optional) A blue “Bonus Tickets” sign is installed inside the playfield, to indicate how many points are required to earn each ticket, and how many tickets are dispensed for each triple basket. The sign shows the manufacturer's recommended settings for the game software. If you want to change these numbers, a supply of small blue decals is provided in the coin box. These should be pasted over the existing numbers on the Bonus Tickets sign. Refer to Chapter 2, Program Modes, for how to change the game software to your desired settings.

Special Precautions

WARNING To avoid electrical shock, do not plug in the cabinet until it has been properly inspected and set up for the line voltage in your area.

This game is designed for indoor use only. The game must NOT be installed outdoors or under the following conditions: ° In areas directly exposed to sunlight, high humidity, direct water contact, dust, high heat or extreme cold. © In locations that would present an obstacle in the case of an emergency, i.e., near fire equipment or emergency exits. On an unstabie surface or subject to floor or other vibration. This cabinet should be connected to a grounded, threewire outlet only. If you have two-wire outlets, we rec-

Page 11

Hoop It Ur Operator's MANUAL & CHAPTER 1 — SET-Ur

ommend that you hire a licensed electrician to install grounded outlets. Players can receive an electrical shock if the cabinet is not properly grounded. Make note of the power consumption when you set up this game so that you do not overload your electrical circuit. See Table 1-1 for the power consumption and the other important specifications of this game.

  • Be sure to switch the power OFF before replacing any parts or connecting/disconnecting the electrical connectors. ¢ DO NOT attempt to repair the printed-circuit boards (PCB) yourself. This will void the warranty. The PCBs contain sensitive components that could easily be damaged by the small internal voltage of a multi-meier. Always return the faulty PCB to your distributor for repair. « When unplugging the game from the electrical outlet, grasp the plug, NOT the cable.
  • Make complete connections to ali the PCBs and other paris of the circuit. Insufficient insertion of ICs and connectors will lead to unreliability and possible damage to the machine.

Charact Specificat Input Current 3 Amps Line Fuse Rating 4 Amps, 250 V, Slow-Blow Line Voltage 102 to 132 VAC, 60 Hz Temperature 37° to 100° F (5° to 38° C) Humidity Not to exceed 95% relative Width* 31.25 inches (80 cm) Depth* 35 inches (89 cm) Height* 75 inches (190 cm) Weight* 350 lbs. (159 kg) *Unboxed

Table 1-1 Game Specifications

Inspecting the Game

Inspect your Hoop It Up game carefully to ensure that the game is complete and was delivered to you in good condition. Inspect the cabinet as follows:

  • Examine the exterior of the cabinet for dents, chips, or broken parts.
  • Open the lower-rear access panels. Unlock and open the coin door. Inspect the interior of the cabinet as follows:

a. Check that all plug-in connectors on the cabinet harnesses are firmly plugged in. Do not force the connectors together. The connectors are keyed so they fit only in the proper orientation. A reversed connector can damage a printed-circuit board (PCB). This will void your warranty. b. Ensure that all plug-in integrated circuits on each PCB are firmly plugged into their sockets. c. Check that the liquid crystal display (LCD) on the Game PCB is securely plugged into its header connector. The game will not operate if this display is loose. d. Inspect the power cord for any cuts or dents in the insulation.

e. Inspect the power supply. Make sure that the correct fuses are installed. Check that the harness is plugged in correctly. Check that the green ground wires are connected. f. Inspect other sub-assemblies, such as the controls, printed-circuit boards, and speakers. Make sure that they are mounted securely and that the ground wires are connected.

Controls and Switch Locations

Ali the controls are located in the lower rear of the cabinet or behind the coin doors. The following paragraphs describe these locations in more detail. Three small potentiometers are mounted on the Hoop It Up game PCB. To adjust these, you need a small (jeweler’s) flat-head or Phillips-head screwdriver.

Power On/Off Switch and Main Fuse

The power on/off switch is a toggle switch located on the power entry module, above the cabinet’s lower rear panel. This is also the location of the game's main fuse.

Ticket Dispensers

Two ticket dispensers, one for each player, are standard in the Hoop It Up game. Servicing information on the mechanisms is provided in the Deltronic Labs ticket dispenser manual, which was included in your Hoop It Up game.

1-3

Page 12

Cuarrer 1— Set-Up % Cops OPERATOR'S MANUAL

Liquid-Crystal Display Liquid-Crystal (LCD) Contrast Adjustment Display Keypad

Balance (tor Distortion Somme Noturre Elimination)

Figure 1-1 Operator Controls on Hoop It Up Game PCB

Liquid-Crystal Display and Keypad

These components are mounted on the Hoop It Up Game PCB located inside the lower rear access panel. (Refer to Figure 1-1 for the locations of all operator controls on the game PCB.) Use the keypad to set the game parameters (options), game cost, and to perform the test functions. To access the game PCB, unlock the lower rear panel and press the appropriate keypad pushbuttons while the power is turned on. You may need to use a flashlight to read the LCD. A small LCD contrast adjustment potentiometer is available next to the LCD; this brightens or darkens the display (see further details in the following section). Refer to Chapter 2 of this manual for more information on the game parameters and test functions.

Adjust Contrast of LCD

Turning this potentiometer (labeled LCD Contrast) all the way counterclockwise increases the contrast to maximum, This maximizes the legibility of the characters shown on the LCD.

1-4 Volume Control

The volume adjustment potentiometer is on the game PCB. Turning this potentiometer in small increments adjusts the current volume setting.

Balance

This potentiometer is intended for eliminating sound distortion in Hoop It Up. It should be set about in the middle. If you hear distorted sound, turn this potentiometer until the sound improves.

Ticket Counter

The mechanical ticket counter is located inside the upper coin door. It is mounted against the internal wood panel. Note that a separate resettable ticket counter is available in the game software. Refer to Chapter 2 for more details.

Coin Counter

The mechanical coin counter is located below the coin box, inside the lower coin door. Again, a separate resettable coin counter is available in the game software. Refer to Chapter 2 for more details.

Page 13

Hoop ir Ur Operator's MANUAL CHAPTER 1 ~ SET-UP

Setting the Coin, Ticket and Game Options

The Hoop It Up coin and game options are set in the test modes. Please refer to Chapter 2 for the recommended settings and the procedure for setting the options.

NOTE To maximize earnings, refer to Chapter 2 for how to fine-tune the ticket payout.

Game Play

This section describes the features and play of the Hoop It Up game.

Introduction

Hoop It Up is a unique basketball redemption game with two-player competition. Based on the successful “3 on 3” basketball tournament event of the same name, Hoop It Up is a head-to-head game that has players shooting for triple slam-dunk action. Two players compete in a timed game for the high score. Using a real basketball control to shoot air-activated balls, players try to score with single, double or triple baskets. Bonus points are awarded for triple baskets, An on-court announcer, themed music, and a large LED score display add to the fun and excitement. Additional play modes include one player against the clock, and an advanced game option where players shoot for lit baskets.

Game Play Hints

Players should attempt to score as many tripie baskets as possible to obtain the highest score possible. A triple basket is awarded an additional 3 points, therefore scoring a total of 12 points. There are two aspects to consistently achieving the highest scores at Hoop It Up — shot pacing and bali placement. Players should develop a rhythmic shooting pace in striking the ball control, therefore allowing each ball loaded into the shooter to settle in. Too fast a pace leads to inaccurate shooting and more bouncing balls in the playfield. These create obstacles that lead to more frequent blocked shots. As for ball placement, though, there may be different ways of making a triple basket or 12-point play; backboard or bank shots may provide the most consistent method of getting triple baskets.

The goal is to achieve the highest score possible before the game timer sounds, ending the game. For ticket dispensing, players are awarded tickets based on score and number of triple baskets, which are operator adjustable. An audio cue of “That’s a new record!” will be sounded when a player's score is equal to or greater than the prior high score. The high score is displayed and retained indefinitely, unless reset through the option menu. (Refer to Chapter 2 for details oa how to reset the high score.) In a head-to-head competition, if the scores are tied, the game will go into overtime, extending the game timer another 10 seconds. The first player to score a basket wins. If players are unable to score during the extended time, the game will end in a tie.

Advanced Game Mode

During an advanced game, players must attempt to shoot balls into whichever

1-5

Page 14

Cuaprer 1— Set-Up & Hoop Iv Up Operator's MANUAL

baskets are lit by red LEDs. Double and triple baskets are awarded after first scoring a lit basket. There are no bonus points given during an advanced game. To enter the advanced game mode, players must hold. the start button down while inserting coins and then release it. At this point, the start button should be lit, indicating credit for coin(s) inserted. To start an advanced game, press the start button.

  • When selecting the advanced game, coins must be inserted one game at a time.

1-6 For head-to-head competition, only one player needs to select the advanced game if both players want to be in the advanced game mode. . The advanced game mode cannot be accessed if there are existing credits on the game. The game defaults to normal game mode for the remaining credits, unless players insert additional coins to activate the advanced game mode.

Page 15

CHAPTER 2

Test Functions

INTRODUCTION

LSE THE HOOP IT UP® test func- ~ tions to check the condition of the

game circuitry and controls. You

will see the test-function information on the

liquid-crystal display (LCD) installed on the

game printed-circuit board. Also, you can use

the LCD and keypad to set the game parame-

ters and game cost. Perform the test when

you first set up the game, each time you col-

lect the money, or when

you suspect game

problems. This chapter

describes the messages

displayed in the test

functions and explains each

of the tests. The test descriptions and expla-

nations are arranged in the order they appear

as you step through the entire sequence.

Page 16

Cuaprer 2 — Test Functions @ Hoop IT Up Operator's MANUAL

Using the Liquid-

Using the Liquid Crystal Display on the Game PCB

All accounting displays, option adjustments, and tests are made using the keypad with eight pushbuttons located on the Hoop It Up Game Printed-Circuit Board (PCB). The liquid-crystal display next to these pushbuttons shows which test or option you are currently using. Refer to Figure 2-1 for the locations of the LCD, keypad, and other user controls on the game board.

Figure 2-1 Detalied View of Keypad

Attract-Mode (Accounting) Functions

Four accounting functions are available in the attract mode. They are listed in Table 2-1 and show the accounting data for Hoop It Up. To step through the sequence, press the NEXT or LAST button several times. Be sure to wait at least one second for each function to appear on the LCD, Function Description Coins Number of coins played Tickets Number of tickets dispensed TIC Ratio Tickets-dispensed-to-coins-played ratio Triples Number of triple baskets made

Tabie 2-1 Summary of Accounting Functions

Program Modes

You can enter the Program Mode only when the game is in the attract mode with no credits entered. To do so, press the PROG key on the PCB keypad. The first mode displayed is the Set Parameters mode. If you press the PROG key repeatedly, the remaining three modes (Set Cost $/Game, Test Functions, and Display Memory) are also displayed. The game cycles through this sequence each time you press the PROG key. To enter one of the four modes, press the NEXT key. To exit from the Program Mode and return the game to the attract mode, press the RUN key. Press the PROG key to enter the next mode.

NOTE Adjusting the Payout Percentage Three of the parameters listed below should be adjusted to achieve your desired payout percentage. The parameters are Games Time(s), Bonus Tickets and Points/Ticket. For the Bonus Tickets parameter, we recommend using 5 tickets. However, you could set this number to 4 or even 3 tickets, if you find that your average triples are too high. You should average 1-2 triples per game, based on our recommended settings. Use the accounting functions to determine your average number of triples per game.

Set Parameters Mode

Pressing the NEXT key causes GAME = HoopItUp REV xx to be momentarily displayed. Then the first parameter — GAME TIME(S) — is displayed. You can select another parameter by pressing the NEXT or LAST key. To change the values displayed in any of the parameters, press the INC (increment) or DEC (decrement)

Page 17

Hoop It Up Operator's MANUAL & CHAPTER 2 — Test FUNCTIONS

Parameter Recommended Setting

Game Time(s)45 secondsMiss Time(s)05 seconds
Attract Repeat Time45 secondsTune On?1 (yes)
Award 103 pointsTicket Sound On?1 (on)
Award 203 pointsEnable Tickets?1 (enabled)
Award 303 pointsPoints/Ticket012 points
Bonus Award03 pointsAttract Ball LoadEvery 2 minutes
Bonus Tickets05 ticketsReset Ticket/Coin0 (don't reset)
Game 2 Basket03 pointsReset Triple?O (don't reset)
Minimum Tickets01 ticketReset High Score?0 (don't reset)

Tabie 2-2 Summary of Recommended Settings for All Parameters

key. Then press the ENTER key to move left, or the EXIT key to move right. To exit the mode, press the PROG or RUN key. The following 18 parameters are available: Game Time(s) °

Game clock timer adjustment (number of seconds for game duration). Recommended: 45 seconds.

Attract Repeat Time Initiate the attract-mode audio every x seconds. Recommended: 45 seconds.

Award 1

Point value for top baskets in Game 1. Recommended: 03.

Award 2

Point value for middle baskets in Game 1. Recommended: 03.

Award 3

Point value for bottom baskets in Game 1. Recommended; 03.

Bonus Award

Additional points granted for making a triple basket. Recommended: 03.

Bonus Tkts Number of tickets dispensed for making a triple basket. Recommended: 05.

Game 2 Basket (Advanced Game Basket) Point value for each basket in advanced games, Recommended: 03. Min Tickets

Minimum number of tickets to be paid for any game. Recommended: 01.

Miss Time(s) Number of seconds to wait for a basket before playing the “bad” message. If a score is received within this time, a “good” message will be played. Recommended: 05.

Tune On? 1=Yes

Attract-mode audio to be turned on (1) or off (0). Recommended: 1.

Tkt Sound On?

Special ticket-dispensing audio to be turned on (1) or off (0). Recommended: 1.

Enable Tkts?

Ticket payout to be enabled (1) or disabled (0). Recommended: 1.

Points/Tkt

Score value required to earn one ticket. Recommended: 012.

Attr Ball Load

Attract-mode feature: loads one ball into each shooter every x minute(s). Recommended: 2.

Rst Tkt/Coin This parameter affects the first three accounting functions listed in Table 2-1. To clear the internal software ticket and coin counters and the tickets-to-coins ratio,

Page 18

Cuaprer 2 —Txst Funcrions # Hoor It Up Operator’s MANUAL

choose 1; to leave the counters intact, choose 0, Recommended: 0.

NOTE Both mechanical counters are not affected by this parameter.

Reset Triple? Clears the internal triple basket counter (1) or leaves the counter intact (0). Recommended: 0.

Rst Hi Score? Clears the high score and reset it to zero (1) or leaves the high score intact (0), Recommended: 0,

Set Cost $/Game The 12 parameters in this mode determine the number of coins required for 1-12 games. The game is shipped with these settings: 1 game/i coin, 2 games/2 coins, ... 12 games/12 coins. You must vot set any of the coins required to 0. Also, the number must not decrease in value as the number of games increases. For example, if you set 1 game/2 coins, then you must set 2 games/4 coins, 3 games/6 coins all the way up to 12 games/24 coins. To select one of the 12 parameters, press the NEXT or LAST key. To change the coinage values displayed next to each parameter, use the INC or DEC keys. To select the column of the number you want to change, press the ENTER key to move left, and the EXIT key to move tight. To exit this mode, press either the PROG or RUN key.

Test Functions

LED Dispiay Test Turns on all the LEDs (light-emitting diodes) on the backboard, and steps through the digits 0 through 9 on all four displays. This way you can check that they are ali working. Sound Test Cycles through all audio. This test is mainly for Time Warner Interactive Customer Service use, so that they can check that the audio circuitry is working properly. Press INC to select the next sound, then press ENTER to hear it. Note: The Channel 1 sounds should work, but the Channel 2 sounds do not, because this game uses one channel of audio.

Memory Test A self-running test of all memory components. When completed, you should see the message Memory Okay. Press EXIT when you are done.

Tickets A Test Tests the left ticket dispenser, by dispensing two tickets from the mechanism.

Tickets B Test Tests the right ticket dispenser, by dispensing two tickets from the mechanism.

Port B Outputs, Port C Inputs, Extended Inputs, Extended Outputs, 250MA Out J1-07, and 125MA Out J6-02 The remaining tests allow technicians to test various outputs and inputs. These tests are for Time Warner Interactive Customer Service use only.

Display Memory

This test is for Time Warner Interactive Customer Service use, to check the contents of memory during troubleshooting.

Page 19

CHAPTER 3

Troubleshooting

& Maintenance

INTRODUCTION

» HIS CHAPTER contains maintenance,

troubleshooting and repair procedures

™ for your Hoop It Up® game. The main-

tenance section gives information on cleaning

the parts. The troubleshooting section contains

several tables to help determine ]f

the source of a problem and the

steps necessary to repair it. The

repair section contains the &

steps necessary to remove

and install the serviceable

parts. Together, these three

sections provide a complete guide to servicing

your Hoop It Up game.

Page 20

CHAPTER 3 — TROUBLESHOOTING AND MAINTENANCE @ Hoop IT Up Operator's MANUAL

Maintenance Procedures

Introduction

This section describes the maintenance procedures for all of the major assemblies and components of the game. The maintenance procedures should be performed regularly. ‘We recommend every 3—4 months, One of the important parts associated with the ball shooter is the spanker, a thin metal blade just behind the ball shooter. The spanker should be raised every time one of the rotor prongs passes by it. The spanker assures that the ball shooter is always loaded. Without the spanker, two balls can become wedged together at the high end of the

Problem Suggested Action

Coin Mechanism Problems en Check the wiring connections to the coin mechanism. Check the voltage to the + side of the mechanism. Check the fuses on the power supply.

Ticket Dispenser Probleme Orewa . Check for jammed tickets. . Use the test functions to check the left (A) or right (B) ticket dispenser. . In the Set Parameters test, make sure Enable Ticket Payout is turned on (1). . Check the harnesses and connectors. . If you took the ticket dispenser apart, have you reassembled it correctly? . Make sure all the parts of the ticket dispenser are in good order. Repair or replace parts as needed. Refer to the Deltronic Labs ticket dispenser manual that was included in your Hoop It Up game.

Basket & Microswitch Problems

  • If players cannot easily make triple baskets, gently bend the front of the top basket slightly upwards.
  • If the ball comes to rest on a switch wire, the wire is restricted in its travel. Check by pressing on the clear disc. if the hole in the net is not large enough to aliow the wire to move completely unrestricted, use scissors to cut one of the net strings below the wire.
  • Check for proper operation of the switch wires, by dropping a few balls from above the top net straight downwards. All three switch wires should register scores and should allow the bails to fall all the way down, scoring a triple basket.

Ball Shooter Probiems . Ifthe ball shooter motor spins constantly, the optical sensor wire is probably broken, or if not, the optical sensor itself is defective.

  • If one ball shooter consistently shoots balls to the right or left of the baskets, you need to adjust the right/left tilt of that shooter. (This procedure should be necessary only if you reinstall the entire ball shooter assembly.)
  • If both ball shooters consistently shoot balls to the right or left of the baskets, you probably need to adjust the right/left tilt of the entire game. Use the bubble level inside the bottom of the game, and adjust all four adjustable glides (feet) until the bubble is in the center of the outlined circle. 4, Make sure the spanker is working: it should be bent upwards with each quarter-rotation of the rotor. The spanker ensures that the ball shooter always is fed with balls.
  • If the ball shooter doesn't shoot balis, foam or other debris is probably trapped inside of the shooter. Otherwise, the spring or piston is broken.

Sound Probiems . Check the speaker volume setting: make sure the volume isn’t turned all the way down, The volume is controlied with the small volume control on the Game PCB, ON Check the Sound Test in the Test Functions. This test cycles through all audio. Check the harness connections on the speaker. Check the resistance of the speaker for 4 Ohms.

Table 3-1 General Troubleshooting

Page 21

Hocp Ir Ur Operator's Manuat @ CHAPTER 3 —THOUBLESHOOTING AND MAINTENANCE

ball shooter ramp, preventing any balls from reaching the air cylinder, the lowest part of the ramp.

WARNING Before performing any maintenance or repairs, please observe all of the following safety precautions:
  • Turn the game’s power off.
  • Unplug the power cord from the electrical socket.
  • Secure loose clothing such as ties and long sleeves that could get caught within the game. Secure long hair. 4, Remove all metal jewelry such as watches and necklaces that could conduct electricity from the game's power sources.

Cleaning Procedure for Coin

Mechanisms

Regular use of the coin mechanism can result in 2 buildup of residue and dirt. To clean the coin mechanism, perform the following steps (please refer to Chapter 4 for detailed part information on the coin door):

  • Open the upper coin door.
  • Open the gate on the door that covers the magnet. Use the blade of a screwdriver to scrape away any metal filings that have collected on the magnet.
  • Clean the loose dust and dirt from the coin mechanism. with a lint-free rag or a soft brush. 4, Clean the dirt and residue from the coin path with a toothbrush. Hot, soapy water may be used to help dissolve dirt and residue.
  • Blow out all the loose dirt, and dry the coin mechanism with compressed air. 6, Close the gate on the door covering the magnet. Then close the upper coin door.
CAUTION Never lubricate the coin mechanism with oil or grease.

Cleaning Procedure for Ticket Dispensers

Regular use of the ticket dispensers can result in a buildup of paper dust, residue, and dirt. For detailed maintenance and part information on the ticket dispenser, refer to the Deltronic Labs ticket dispenser manual that was included in your Hoop It Up game.

Cleaning Procedure for Ball Shooter

It is possible for the ball shooter assembly to become clogged with tiny particles of foam from inside the basketball control. If this occurs, you will need a can of compressed air, preferably with a thin nozzle tube, and a clean cloth. Foliow these steps and refer to Figure 4-6:

  • Unlatch the control panel. Loosen and remove the hose clamp that is attached to the hose connector (the bottom metal cylinder under the ball shooter). 2, Insert a screwdriver or pen into the metal tube, and push the white piston inside until it reaches the upper end,
  • While holding the piston in, spray compressed air into all four cylinder exhaust holes (see Figure 4-6 for their locations). Any debris inside should be ejected past the screwdriver into your hand, 4, Unlock the upper rear access panel, open the backboard, and reach into the playfield area. Using a lintfree cloth, wipe any debris from the ball shooter around the white piston.
CAUTION Never lubricate ihe bal! shooter with WD-40 or any other lubricant. The shooter will become clogged and stop working if you use any lubricant. Simply keep the ball shooter clean and free of any debris by blowing air through the four cylinder exhaust holes as described in the previous steps.

Troubleshooting Procedures

You should pinpoint the cause of a malfunction by using the test procedures described in Chapter 2. Any repairs, other than minor procedures such as bulb replacement or mechanism cleaning, should be referred to qualified service personnel.

Page 22

‘CHaprer 3 — TROUBLESHOOTING AND MAINTENANCE @ Hoop IT UP OPERATOR’s MANUAL

Repair Procedures

Introduction

This section describes the repair procedures for all of the major assemblies and components of the game. Before performing any repairs, use Table 3-1 to help discover the source of the problem. The Maintenance Procedures section can also be a good starting point for fixing many game problems before beginning what might be unnecessary repairs.

Ball Shooter Spring and Piston

If you have blown air into the ball shooter and it still does not work, this indicates that the spring or piston has failed. To replace either of these parts, follow these steps and refer to Figure 4-6; 1, Unlock the control panel. 2, Remove the heat-shrink tubing or tape that is used to seal the bottom of the ball shooter against air leakage. 3, Remove the set screw and spring lock washer that secure the metal hose connector to the bottom of the ball shooter,

  • Carefully lower the hose and its connector. With your other hand, catch the piston and spring before they fall out of the ball shooter.

Plywood playfield ‘support |. \

Adjust either of these locknuts. Do not adjust the center locknut.

  • Insert a new piston and/or spring into the ball shootet, The large end of the piston must face down. With one hand, hold the piston inside the ball shooter.
  • With your other hand, insert the hose connector into the bottom of the ball shooter. Reinstall the set screw and spring lock washer.
  • Reseal the area next to the set screw by using tape.

Replacing the Ball Shooter Motor

or Optics To replace either the motor or the optics in the ball shooter, you may be able to leave the ball shooter assembly installed in the game. However, access is much easier if you remove the ball shooter assembly from the game,

  • Unlock the upper rear access panel and open the backboard. Unscrew the three hold-down screws along the bottom edge of the divider net, 2, Remove the three screws that secure the floor-panel metal ramp. Lift up the ramp and slide it out from under the ball shooters,
  • Unlatch and open the control panel. Disconnect the motor harness assembly under the ball shooter. 4, Loosen the screw on the hose where it is attached to the hose connector (under the ball shooter), Slide the hose off from the hose connector.

tighten locknuts so that these spacers become Rubber spacers: do not

completely compressed.

—~_8 I

© Peas Ko

Figure 3-1 Ball Shooter Adjustment

3-4

Page 23

Hoop Ir Up Opzrator’s Manuat @ CHapTeR 3 — TROUBLESHOOTING AND MAINTENANCE

  • Remove the four nuts from underneath the ball shooter assembly.
  • Being careful so that you don’t tear the decal on top of the spanker, gently lift up the spanker blade. Remove the ball shooter assembly. At this point the motor or optics can be replaced on the ball shooter.
  • Ifyou need to replace the optics, remove the hot-melt adhesive that secures both halves of the optical system. Then pull the LED and optical sensor out of their spacers on each side of the shooter frame.

Ball Shooter Right/Left Tilt

Adjustment

If the ball shooter consistently shoots balls to the right or left of the baskets, you need to adjust the righv/left tilt of the shooter. (This procedure should be necessary only if you reinstall the entire ball shooter assembly.) To adjust the ball shooter, you will need a %-inch open or box-end wrench. Follow these steps and refer to Figure 3-1: 1, Reassemble the ball shooter parts as shown in Figure 4-6. Then reinstall the shooter into the playfield as described in the previous section. Do not yet latch the control panel shut,

  • Allowing each ball to settle completely into the ball shooter, shoot several balls at the baskets. Check where most of the balls hit the backboard.
  • If the balls are all shooting to the right of the baskets, swing down the control panel. Adjust the right/left tilt by tightening the nut on the /eft front side under the shooter. If the balls shoot to the left, tighten the right front nut. Continue shooting balls and adjusting the nuts until most of the balls hit the center of the backboard.

Basketball Control

Over time the Spalding basketball cover will become worn. You should replace it before it wears through, to avoid players destroying the foam underneath. The control will still operate correctly if the ball is worn smooth. To replace the cover, refer to Figure 44 and 4-5, and follow these steps:

  • Open the control by releasing both spring draw latches. These are located inside and above the upper coin door.
  • Remove the four locknuts and flat washers under the basketball (bellows) assembly, and the four spacers and carriage bolts above the basketball. Lift the assembly up.
  • For ease in handling, you may want to remove the hose that is attached directly to the bottom of the manifold plate. 4, Loosen all four hose clamp screws, and remove the hose clamp set completely. Remove the basketball cover from the manifold plate.
  • Install a new basketball cover, making sure its cut edge is completely flush with the manifold plate.
  • Reinstall the remaining parts in the reverse order, making sure the reed valve is properly placed (completely flat on the manifold plate).

Speaker

The Hoop It Up game speaker is located under the control panel, at the front of the game. The speaker provides the music and sounds for the game and self-tests. Speaker failure can be the cause of distorted or no sound. To replace the speaker, follow these steps and refer to Figure 4-1;

  • Remove the four screws securing the speaker grille. Remove the speaker grille by pulling it out; then set it aside.
  • Remove the four speaker mounting screws, and lift out the speaker,
  • Disconnect the hamess from the speaker, including the earth ground clip. 4, Replace and reinstall the speaker in the reverse order.

Attraction Panel Fluorescent Light

To replace the attraction-panel light bulb, follow these removal and installation steps:

  • Remove the three Phillips-head screws securing the upper attraction retainer at the top of the game. Lift out the attraction shield and graphics film. 2, Remove the cardboard retaining clips one at a time by pressing on the circular tab and pulling the clip toward you.
  • Rotate the bulb toward you while gently pulling on the bulb to remove it. 4, Install a new fluorescent light and rotate it 90° to lock it in place. Reinstall the retaining clips.
  • Close up the attraction panel area by replacing the graphics film, the shield, and the upper retainer.

Playfield Incandescent Lights

To replace either of the playfield area incandescent light bulbs, follow these removal and installation steps:

Page 24

CuapTeR 3 — TROUBLESHOOTING AND MarnTENANCE @ Hoop It Up OpERaTor’s MANUAL

1, To gain access to the incandescent lights, first remove the fluorescent light (see the previous section).

  • Reach in above the “eggcrate” light diffuser, and unscrew the incandescent light bulb.
  • Screw in a new light bulb into the socket. Reinstall the fluorescent light. 4, Reinstall the attraction shield, graphics film, and retainer.

Backboard and Playfield

Components

The replaceable parts on the backboard are the nets, microswitches, and Ping-Pong-type basketballs on the playfield. To replace these parts, open the upper rear access panel, and follow the instructions below. Nets The string nets should be replaced if they become tom or dirty. To replace a net, follow these steps and refer to Figure 4-3: 1, Open the backboard panel by removing the three upper screws and swinging the panel open. Remove the hoop by unscrewing the two screws on the hoop’s bracket.

  • Slightly push down on the left side of the hoop, next to its attachment bracket. Slide the old net around the hoop and remove it at the open (left) end.
  • Thread each loop of the new net over the open end of the hoop. Make sure you do not siretch the net too much before all the loops are on the hoop; otherwise you may unravel the net. Evenly distribute the loops around the hoop. 4, Reinstall the hoop and net by threading the switch wire and disc through the rearmost net hole. Then reattach the hoop with the screws you removed earlier.

Microswitches

Note that new switches are shipped pre-assembled with the switch wire and plastic disc attached. Replace the defective microswitch as follows (refer to Figure 4-3):
  • Unplug the two harness connectors for the backboard assembly that you are working on.
  • Remove the backboard assembly by unscrewing the two #10 x %-inch screws attached to the rearmost edge of the blue backpost. Lift out the backboard assembly towards the front of the game,
  • Remove the two screws from the defective switch. (A rectangular access hole is provided for each switch.) Slide out the switch towards the rear of the backboard.

3-6 assembly. You will have to slightly squeeze the clear disc to make it fit through the opening. 4, Reinstall the new switch, wire, and disc by carefully sliding the disc through the opening. Turn the switch 90° and secure it with the two screws.

  • Reinstall the backboard assembly by resecuring the two screws into the backpost. Plug the two harness connectors together again, Basketballs Open the backboard panel, and put no more than 6 basketballs on each side of the playfield, on or near the ball shooter. Loading more than 6 balls will cause the ball shooter to jam up, and players will not be able aim the balls correctly at the hoops. You should have at least 5 balls on each side of the playfield.
NOTE We recommend using only high-quality basketballs, which will be less likely to crack. Such balls have no visible seams. These balls should be readily available in toy stores. If you cannot easily find these balls, call Customer Service for sources. In an emergency you can use white table tennis balls, which are the same size and weight.

System Logic Assemblies

This section describes the repair and maintenance procedures for the major assemblies and components related to the system’s logic and electronics. This includes the printed-circuit boards (PCBs) and the power supply, These components are housed in the bottom of the game cabinet, behind the lower rear access panel. We recommend that this procedure be performed by qualified service personnel only. Hoop it Up Game PCB The Hoop It Up game PCB is responsible for the game sounds and game play. Failure of the game PCB may result in erratic or no game play. If this is the case, repair or replace the game PCB by following the removal and installation steps below.

  • Make sure the power to the game is turned off. Unlock the cabinet's lower rear access panel,
Page 25

Hoop Ir Up Operator’s MANuaL @ CHAPTER 3 — TROUBLESHOOTING AND MAINTENANCE

  • Remove the four nut/washer assemblies that secure the metal game-PCB cover.
  • Disconnect the hamess connectors from the game PCB, 4, Unfasten the six screws that secure the game PCB to the inside wall of the cabinet. Remove the game PCB.
CAUTION Before handling static-sensitive componenis, properly ground yourself to remove any siatic charge buildup.
  • Re-install the game PCB by following the previous steps in the reverse order. Be sure to reinstall the game PCB cover, since this is required to meet FCC EMI emission requirements. Power Supply The power supply is responsible for providing power to all of the game assemblies that require it. Failure of the power supply may result in erratic game play or no power at all. To remove the power supply assembly, perform the following steps:
WARNING The power supply can contain high voltages even after the power is turned off. To avoid injury, observe all of the safety precautions before working on the power supply. (Refer to the warning in the Maintenance Procedures section at the beginning of this chapter.)

. Unlock and remove the lower rear door of the cabinet. . Disconnect the wiring harnesses from the power supply. . Unfasten the two screws that secure the power supply assembly to the cabinet floor, and remove the power supply assembly. . Re-install the power supply assembly by following the previous steps in the reverse order.

Page 26

Cuaprer 3 — TROUBLESHOOTING AND MAINTENANCE @ Hoop It Up OPzRaToR's MANUAL

NOTES

Page 27

CHAPTER 4

Parts Illustrations

PART ORDERING INFORMATION

HIS CHAPTER provides information

you need to order parts for your

game. When you order parts, give

the part number, part name, the number of

this manual, and the serial number of your

game. With this information,

we can fill your order

rapidly and correctly. We

hope this will create less

downtime and more profit

from your games. Time Warner Interactive

Customer Service phone numbers are listed

on the inside front cover of this manual.

Page 28

Cuarrer 4 —~ Parts Incusrrations ¢ Hoop It Up OPERATOR'S MANUAL.

054539-01 Attraction Shield 054717-01 Attraction Fim 054537-01 Plex Mounting Bracket (behind the lower retainer) 054532-01 Upper Attraction Retainer 176020-212 #8.x 3/4" Lg, X-Rec. Black LPW Screw

054536-01 Lower Attraction Retainer 176020-212 8x3/4"Lg. X-Rec. Bik. LPW Screw Decal

Scorebo:

054535-01 Playtield Plex Assy.

054720-01 Divider Net 178032-002 #10 Screwhole Wire & Cable Tie Decal

Playtield 054713-02 Right Side Attraction

054718-01 ‘ard Decal

A054219-01 Backboard

054719-02 Inner Back Pane!

054533-01 Door Hinge

178085-111 5.5" Lg. Wire & (054831-01 Cable Tie! Side Shield 176015-112 Retainer #10 x 3/4" X-Rec. Tapping Pan Screw en seg tate Outer Back Panel 8-32 x 50" Lg. cea Pan Screw 054203-01 05872401 Rear Floor Ticket Sign Panel (Ramp) 054715-01 hone aay oy Playfield Decal Ball Shooter Assy. | 478403-001 motte 2" Cloth Carpet osa7e1-01 f Tape (80" required) i 054716-01 oe Ramp Decal

148019-001 102055-001 6" x9" 2-Way Playfield Dampener Pad 100W 4-Ohm 054712-01 Speaker Side Panel 176015-116 bean #10 1"Lg. Deepthread Screw 054534-01 Speaker Grille 176020-212 Items Not Shown:

#8a Lg.X-Rec.A053415-01178244-212
Black LPW.Sorew!Fluorescent Lamp—«#12.:'1.25" Style F
054723-01Fixture Assy.Type 4 Stainless
Coin Door170003-001Hose Clamp

a Jorescant Li LED Display Bracket Fluorescent Light isplay Brac

a7i093-001178292-00%"150041-001
__Over/UnderFluorescent LampPower Cord
Coin Door wiCashRetaining Clip178400-001
Box Assy.tritaeoot‘A054494-01Basketball-Pattem

Hoop It Up Game Ping Pong Balls aaa ees PCB Assy. (6 Per Pack) #10-24 x 1 1/4" Lg. 054525-01 178263-0402 Bik Carriage Bolt PCB Mounting Plate 1/4 x 1/8" Thk. Black 17026-0040 054785-01 Foam Tape Control Hose #10-24 NutWasher Assy. 175014-1040 #10 219 x 500" Flat Washer

Figure 4-1 Cabinet-Mounted Assemblies, Front View A054490-02 Rev. C

Page 29

Hoop It Up Operator's MaNuAL “ Cuaprer 4 — Pars IntusrRATIONS

Items Not Shown: 084713-01

A054494-01054529-01A054305-02Left Attract

Hoop ItUpGame PCB White Light Panel_Left PCB Display Assy. . Side Decal

Assy.054526-01A054552-01
179239-001PCB Cover‘Main Harness Assy.
250V Medium-Base Lamp‘A044072-01‘A054553-01
Receptacle12V Ticket CounterAC Harmess Assy.
170002-001‘A054564-01‘A054554-01
BOW 120V Soft WhiteGround Braid Assy.Door Harness Assy.
Medium-Base‘A054305-01‘A054555-01

Incandescent Lamp Right PCB Display Assy. Light Hamess Assy.

054512-01 Playfield Door

054514-01 Rear Door 176020-220 #8x1 1/4" Lg. X-Ree, Black LPW Screw 178197-001 Lock & Key Assy. 178276-002 ‘Wood Anchor Washer (2 Places) 178198-002 11/2" Offset Cam

054510-01 043839-01 é

PCB Access DoorLeg Leveler054712-01

176020-220 Plate < Side Panel

#8x1 1/4" Lg|178255-004Decal

X-Rec. Blk. LPW Hl 3/8-16 x 1.50" 7 Screw Adjustable Guide 178399-001 ‘ST-403 .655 Dia Circular Level Hoop It Up Self-Test 178399-002

Label.‘A054563-01Circular Level Flange
178197-001.On/Of Assy.(not shown)
Lock & Key Assy.NS176003-108084862-01

‘TM-403 4x 1/2" Lg Hoop It Up X-Ree, Pan Hd feos

Operator's Manual146008-4022#10 x 3/4" X-Rec,

4 Amp 250V SAG Tapping Pan Screw Siow Fume 177026-0038 8-32 Nut/Washer Assy. y ve

Figure 4-2 Cabinet-Mounted Assembiles, Rear View A054490-02 Rev. C

Page 30

Cuaprer 4 — Parts ILtustrations & Hoop IT Up Opzrator’s MANUAL

25" Hole, Bik. Nylon 5 mm/T1-3/4 LED Mount | ~ Microswitch Wire “]

160076-02 24 gm, 5A/250 VAC, Gold SP Side-Wire Snap Switch

Orange

172025-3212| Black 4-40 x .750 X- Rec Zine Pan Screw (6 Places)

138027-1001

(3 Places) |

A054557-01 LED Harness ‘Assembly

Green

Black

Violet

‘A054556-01 Switch Harness Assembly 054725-01 | Hoop Disc (6 Places)

175014-1016 125 x 250 x .022 Steel/Zinc Flat Washer (6 Places)

177010-232 4-40 x .750 Polymer-Lock Regular Hex Locknut (6 Places)

053014-01 Backboard Backpost

Figure 4-3 Backboard Assembly A054219-01 Rev. A 053489-01 Backboard

172025-3606 6-82 x 375 X-Rec Zinc!— Pan Screw (6 Places)

Page 31

Hoop IT Up Operator's MANUAL @ CHAPTER 4 — PARTS ILLUSTRATIONS

054530-01 Control Panel 054714-01 Control Panel Decal 160060-107 Switch Assembly wi/Silver Contacts

A054220-01 Left Bellows Assembly

75-5524B | 1/4-20 x 1 1/2" Lg a Carriage Bolt (4 Places)

A054559-01 Control Panel Harness Assembly

178272-6912 .38 x ..75 Alum. | 3/4" Dia. Spacer (4 Places)

A054220-02 Right Bellows Assembly

175014-1050 .281 x .625 1/4" Flat Washer (4 Places)

177010-244 1/4-20 Locknut i (4 Places)

Figure 4-4 Control Panel Assembly A054491-01 Rev. A

Page 32

(Cuaprer 4 — Parts In.ustrations @ Hoop It Up Operator's MANUAL

054726-01 Control Cover!

054224-01 Open-Cell Foam

054225-01 Closed-Cell Foam

75-2812S 8-32 x .75 Stl/Cadmium X-Rec Round-Hd. Screw 053487-01 “ j Valve Plate

178319-6002 4/2" Round Spacer (4 Places) 053488-01 Reed Valve

178244-244 Hose Clamp (4 Places)

053011-01 Manifold Plate

CAUTION When installing the reed valve, make sure that it remains 177010-238 absolutely fiat on the manifold ;—______________| 8-32 Hex Locknut plate. (4 Places)

Figure 4-5 Bellows (Basketball) Control Assembly A054220-01 (Left) or A054220-02 (Right) Rev. B

Page 33

Hoop Ir Up Opzrator’s MANUAL & CHAPTER 4 -- PARTS ILLUSTRATIONS

0554211-01 Shooter Frame Endplate

178065-111 / 72025-: 5.5 Wire & Cable Tie / He % on te Macee} A054558-01 Pan Screw Motor Harness Assy. (9 Places) 138026-001 / Darlington Output, A NPN, 250MN, TO-18 054217-01 Photo Detector | ~~ Photo Sensor/- 106006-001 LED Spacer .45 Diameter (2 Places) Hot Melt Adhesive 178311-1006 177010-236 3/32 Clear 6-32, Reg. Shrink Tubing Polymer-Lock Hex Locknut (8 Places)

-145013-001 19.1 VDC 19.5:1 Ratio, 396 RPM Gear Motor

054210-01 Shooter Frame

a a /

SY 175017-2011 | 47025-3206 #4 Zinc Reg. Duty |~ 4-40 x .375, X-Rec, Helical Spring Zinc Pan Screw Lock Washer (3 Places) (3 Places)

NOTE Vinyl tape, such as electrical tape, is an acceptable substitute for heat shrink tubing. After tightening the ‘set screw on the cylinder weldment, use either material to seal the space between the cylinder and the hose connector. This eliminates any air leakage. 138019-001 1R Red 940NM TO-18 Light Emitting Diode 106006-001 .45 Diameter Hot Melt Adhesive 178311-1006 9/92 Clear Shrink Tubing

: | Cylinder Exhaust Hole, for reference (4 Places)

~| 053008-01 Cylinder Weldment 75-4003 10-32 x 3/16 Steel Hex Cup Set Screw 178311-0064 1” Dia. Black Heat-Shrink Tubing (See note below.) 175017-2013 #6 Zinc Reg. Duty Helical Spring Lock Washer » 172025-3612 x 6-32 x .750 053009-01 Pan Screw /\ Hose Connector (9 Places) / / 178006-022 +328 x .75, .016 f Compression Spring

Figure 4-6 Ball Shooter Assembly A054221-01 Rev. A

4-7

Page 34

Cuapter 4 — Parts Iniusrrations & Hoop It Up OPERATOR'S MANUAL

99-15104 pitas Base Plate W/PWot & Stud 99-15025 Left Coin Inet

99-15113 Key Hook

99-15056 ‘Screw for Bezel

99-15096 ‘Switch Adjuster

99-15056 Screw

99-15131 Elastic Locknut | 98-5132 ‘Snap-on Sleeve

99-15130 ‘Snap-on Ciip

99-15133 Hold Down Bracket

(99-15056 Screw for Bezel 99-15128, po-1s0e7’ NutWasher for WS Mounting Screw) C0" Ret. Plate 99-15028 Coin Return Box

99-15056 Screw for Bezel 99-15129 Mounting Stud |— (2 places)

99-15051 99-15134 Lamp Holder 4-40-1" Pan-Head Screw

Breoket Mounting Screw

99-15042, 99-15085, ‘Switch Coin Door Harness

Figure 4-7 Over/Under Coin Door Assembly 171093-001

Page 35

Hoop It Up Operator's MANUAL @ Cuaprer 4 — Parts ILLustRations

99-15038 99-15036 Bezel for Button Cover

99-1501 through 99-15012 Return Button

99-15039 Bezel for Cover

99-15125 Frame Hinge Screw

99-15052 Spring for Button

99-15088 Clamp

99-15135 Frame Clamp Screw

99-15116 Upper Door|

99-15115 Lower Door

99-15114 Die Cast Frame

99-15111

  • Coin Counter

99-15089 9915127 Lock Assy Meter Mounting ‘Screw

Figure 4-7 Over/Under Coin Door Assembly 171093-001

Page 36

Cuaprer 4 — Parts Ixuustrations Hoop Ir Up OPERATOR'S MANUAL

A048494-01 PS. Ground dumper Assy. (see note below)

72-HA4608S #6-32 X .50, X-Rec Thd. Form Screw (4 Places)

149018-001 -5V@ 1A, 12V@3A, +5V@15A Power Supply

179372-003 7/16" 20A 3-Ckt, 2-Row Terminal Block

179225-2202 2 Pos. Fuse Box 146008-3022 250 V, Slow Blow, 3 Amp Fuse

049292-01 Power Supply Fuse Label

037640-01 Power Supply Warning Label

1-01 - — Power Supply base’ ‘Crass 178265-001 72-HA4606S ‘A054643-01 L-Style Nylon 30 #6-32 X 3/8, X-Rec Dual Triac PCB Assy. PCB Standoff Thd. Form Screw (4 Places) (6 Places)

NOTE Attach jumper from earth GND to signal GND on power supply terminal block.

Figure 4-8 Power Supply Assembly A054562-01 Rev. A

4-10

Page 37

CHAPTER 5

Wiring Diagrams

INTRODUCTI

HIS CHAPTER contains the wiring

diagram for the Hoop It Up game and the Score Board PCB schematic

diagram. (The assembly drawings are illustrated in Chapter 4, Parts Illustrations.) Copies of

the complete Hoop It Up Game PCB schemat-

ic diagram are available free of charge by con-

tacting our Customer Service Dept. See the inside front cover of

this manual for the 5

address and tele-

phone numbers. a

Page 38

Cuaprer 5 — Wiinc DiacraMs @ Hoop Ir Up Operator's MANUAL

P79 LEDR

LaNR. wi ul QUICKSILVER GAME BOARD

ya LEDL

wv wien W/0R

iC P79 SPKR

BNBua| +
w#42||-5Bs
naem0?aT] spare«28%
toeer wt[PLBUY 3 || NoveH sens A mngEbse
azitimme aor | 52555ES
ure a |1 || spare3335852 Sees
g 2°888EB SEEP
iainewson[soa a)
‘TICKET OUT2 ye-
user ay| | 8 __eBRE>|5)3)>

= toe ‘au

TieKer2*

DISPENSER (R) 3% RIGHT * SERIAL DISPLAY am TroKer 2 Psd OUT R DISPENSER (L) 3} ap + a

arp 60 au {] , |you w||3 [vw aw || [ven an || 5 [on on ||? [ow TH]? Oy wile i aii? ie mw ||2 [ew er] 9, [or A A ay aw | | 22 aw

MP rey xey| 2 soLi| 3 at Lesv| 9 soz| 4 | 8Y resv| 2 | RM

arp 30 ER a] Lil fy] | ose (CT oc] Fa So ae 28 0" : on

\ FLUORESCENT Va LIGHT a3 aS & m3

ag var LINE FUSE 1HPUT re ox 78/782 ox POWER

/\BKBKBK
arCLOT1¥SUPPLY
FILTERjw7+«

r i] POWER ENTRY MODULE

Figure 5-1 Hoop It Up Game Wiring Diagram 054551-01 Rev. A

Page 39

054551-01 Rev. A Figure 5-1 Hoop It Up Game Wiring Diagram Pia 10 | |noven sense 8 CON IN SW A

SPARE

ae 70 BK BK/Y ‘ 9 | |akLL our sense @ | {BALL our sense A

oR oR oR oR +20¥ com

ok [AWARD SW 2A AWARD SH 2A

P70 SR ok] ake BkW Ke 4 | [AWARD SW 3A

NL! Pia?

oR ‘OR/aK oRraK OR/BK tay com

Cl ‘ON/3K. oN/8K en/aK

W/K W/BK W/BK 2 | |awano sw 3 | |awaao sw AWARD Sw 6 | [corn IN SH 8 7| | starr sw 2 8 || starr sw 2 pias

BALL MOTOR B2 (R)

BALL MOTOR B1

R

oy GN

BKIY WOR aes 22k,

BK/M BKY

BALL MOTOR AZ

BALL MOTOR AL (

Y7BN

BK/W wy Y/0R

= eoakune

corn Do0R Y o OR ¥ Psd 28h Y mn 8N a oy YIN Pys 24 ysor

GAME SELECT LAMP 2

2 ||GAME SeLect LAMP 1

#22¥ COIN METR GND COIN METR ND TKT METR AV TRT HETR QUICKSILVER GAME BOARD

P/3 36

=a RIGHT

START SW. 1 LerT ))) start sw. 2 Hoop It Up Operator's Manual @ CyapTer 5 — Wiminc DiaGRaMs

Page 40

Cuaprer 5 — Wiminc DiacraMs @ Hoop Ir Up Orzraton’s MANUAL

“H

eTBone ve«STROBE

1 sede SL

1ssest

2 ce 07 000eF Jor sioooer | 1000%r

a w ‘cnses34 ews633h

ours [8 —-» UTom b.Fry
one >& Saneam Pe75wr
ours 7. auraane75Ws
ours [8 + teamsTSNees
ours [8 + ausom Pe333755
ore fos wregts rayaas
Srebiz—t aea gena

p2—s ours Sap 4S

‘sw‘SOIN21 sow
soouTsoout 32°snout
ors [512uMota11g common13a7
oo pene acura Ts) # eam (|Sot Piaaa
ot 1S yyy 8 sours TO) ¢one PasTez_560
wt bese a amie 8)ieEr
orye oor —TIegun syaa _560

Pie es a5 ora? yo

ureF182368
owns [285 gs outa 17) feoms £29neo
‘ourie |5.20us 8 L.3 a i rygums [205e0roo RSS—
svaoae «| srrosead7

if mst |

out b38m2uz]4 coon pg —s5"zea2
eurie (le 7tw Out® 18/9 ANoe [ey 88on Pe7 Nsco

ourig 35 yBTE_ortas 10) ¢ A pS ate iris py, R075 ure -—

.oureeovree p2znS
aureaours 56caeco

rt 7 outes bi ro +0 +

acux «40 Jeux Lenn | a2 NOaaciK—**leux Lowa

3 _,+sv

ures 30 ay B18ures 2) 4 comon 15ourtes 53%sag.
ouresispez_out26 131 5 “Ayooe | og —¥*8YA850sco
a5 75‘ure?Re aayTze ae
outa? baw —couta?seg we 550
ouT2eSuTe8ouTzs 532.aePraJ
uresourea p3eyy tae S80
ouT30out30 p35=emi
oursourai 5.38mo S80

outs

.ourse108

BRE aad ee OLAMPS a +8y +o NINA H2V eo? sili key

outealRG1 POUT] 4° TO BASKET LEDS
OUT2 &Rez 160POUuT2 55 TO BASKET LEDS

ouT3: RG3 POUT3 6 To BASKET LEDS

ourswoa_160OUT S770 FLASH SULAS
cus:+Ta R85 POUTS 3g TO FLASH aULaS
ours+esPOUTé Sg To FLASH BULBS

out? <p 8B7FOUTTS 1 TO FLASH BULBS

phnme_ 8Pours <1)

ew +

evo. 1"?

Figure 5-2 Score Board PCB Schematic Diagram 054305-01 Rev. A

Page 41

Hoop Ir Up Operator's Manual @ Cuaprer 5 — Wininc DiaGRaMs

ovoSywre HOLEww
cart novelea Ts TeDe Le

anre Hoe [ieee ae eae ees eer wre wove cw

ORANGE, s Diss cura}, common | 3s asy ouraa 3a) 4 nove [Se 45¥ auras a0} a sv

aurae8/6,av

(ours? Ze

aursaaE”
auras—ai|g feeours = MvSe59 Gt ws _|

maga R25 opp cee

  • hal MTNG125- DUTaO v5059) 2" NS neo outio » Ee
OiseosOoOo
ouran2] 4 Squion | etieyLAMPSJOUT
oura2eeenvsosa 2* KsOMAIN
aurasao} Aorn ee
auratiteae

auras 7]

aurasals«
aaocurse M5059 Zt ns_|2Dis4DissDiség

i 8 cre!

ys ——] 9? =a oPaFa5 | 3
.sale8

ouras +8 aco a” L

ours.7), coMMON |_1y410vouta « M¥5059xs
on5 42v.oi

c Q urge w M5089 2 WS >

FReo Ryaoo

nvsos 2" As ouras eS

aeDisO Dist Dis2—Dis3
1aurae = 50592" usi)ie)

av

fevcas°fe}
©ddd1d2

fe) (e}

JouTOSERLJSERRNOTES FOR HOOP IT UP:
‘eND1NI1SHD.1
452br2no2NS - Do NOT stuff
ouragAsv3a3SR - Stuff right side only
oestev+8vaebemaSL - Stuff left side only
curse:sev4som4
euro 2a?Soinweysoo8
ours8soouT8acl8
ourss 209acike09ey
ouTss10sra0ge10sTaoueto
wey —5 11TANKnBLANK10

sR 5

an a

csceceocat
woacooeta

Figure 5-2 Score Board PCB Schematic Diagram 054305-01 Rev. A

Page 42

Cuarrer 5 — Wrrinc DiacnaMs @ Hoop IT Ur OPzRaTor’s MANUAL

Page 43

Tse

ira i Seller -warraugs that the prnedsircult boards and pens covered by this war by ate fred from, differs Tn inatéral and Workmanship Under Acemal use and strict for a peaas of oinety (90) days from dae of shipment. Seller warrants that products containing Videx displays, laser-video-disc players, and/or CD-ROM playes.cve fee from defecis in gaterial and workmanship unde femal use and gervier for 3 period cf 11) ihity (50) ctays fram «tare of sip ment fon video dispisys: (2) one year froth date of akzpouent for laser vitler~ tis playersgid GY nines) OX) divs from date of-shipment for CD-ROM play

ers None’ gf the Seller's other paris to the product are envered by (his

Wwatramny, If thé prowdunt Géscoiset! it thie matual fails fo Conform 10 this. warranty, Seller's sole listulity shall be, at its opiion, lo-repsin.seplace. of credit Buyer's account for sich prorlucs(s} which gfe returned te, Seller slong sad warranty period, provided, @} Sailers prompll-podfiedtinwriting Ypon cStovely by Buyer (iii said prodycts ot defrenve;

  • Such. products are serurped presaldite Selle. memnuiucturiig fality i Ark piss, California: arxi (OSelles's examination of sctid products cliscloses ty Seller's, satisfaction tirst suet alleged Ueltets cxisiodand were aol Gaused by impruper shipping or Gandlling, accidens, misuse, fegiec, aliecitiion aaproper tepair, installation, or lmproper testing: Tend event glial Selle? be Table (it loss of profits, Was of ise, incidiermal, spec- Wlatve or cansequentia Gomapen: Exceps for any express Wartinty gb forth in A-reratiin cutract hereon Seller eXpres 07 (iplted warren ites. chiding wioranties yf merchantability ate futnexs for i particular merpete

‘The ase of any non-T Wil Time Warner Interactive perid may vnldl the berms of your werranry The aol op nent Wiens may alsp-adissedy <iliee the-anfey of paar gare and. cause (icy % yoy srl othete, Aven ceang cS Wizepplice! eooponents wilh war gathes, ic. order lo enmire your saleoy Distritutors of Time Ware: lgerieiive/Aiar! Games producs are indeperuically owned cent oparaied tn ther judignent ancl withinul THY Amat authorizailoe ye aprroval, duirihigre sell pats ior accessories other than SWE parts or ecvessorics, Tine Warp Intesar- Uve/Atar: Games Cosposation disclaips sespensthility far damages, fojurtes op enonpente loss. caused, by a GearBrtor’s use nf any HeoTWi pan or any modification by disitivins, tackating labor, io TWi produces

Page 44

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.