CATHODE RAY TOMES

Tail Gunner

Tailgunner (Cinematronics, 1979) · Manual · 69 pages · 61 sections · original scan

Page 1

|S Ete SERVICE CINEMATRONICS Fie MANUAL

Page 2

CINEMATRONICS, INC.

1466 Pioneer Way

E] Cajon, California, 92020

TELEX: CINEMAT 697891

CALL TOLL FREE: 800 854-6577

IN CALIFORNIA CALL: 714-440-2933

SALES: 8-5 (PST) WEEKDAYS

SERVICE: 7-5 (PST) WEEKDAYS

Page 3

OPERATION AND MAINTENANCE

MANUAL

CINEMATRONICS, INC. 1466 PIONEER WAY EL CAJON, CA. 92020

Copyright 1979 All Rights Reserved

Page 4

WARRANTY

Cinematronics, Inc. warrants the goods to be free from defects in material and workmanship under normal use and service for a period of ninety (90) days from the date of delivery on all parts except switches, buttons, lights and fuses, for which the warranty period is thirty (30) days from the date of delivery. Cinematronics makes no representation or warranties concerning the goods whether express or implied by operation of law or otherwise, including those of merchantability or fitness for any particular purpose, or with respect of patent infringement, except as may be specifically made herein. Cinematronics limits its warranty obligations herein to the repair or replacement of such parts which have been returned to Cinematronics’ plant at purchaser’s expense and which examination shall disclose to Cinematronics’ satisfaction to have been so defective and to the shipment of such repaired or replacement parts to the purchaser F.O.B. the shipping point.

This warranty does not apply to any Cinematronics product which has been altered or repaired by unauthorized personnel or service facilitiesor any products which have had the unit serial number altered or removed.

Upon acceptance of the goods, the purchaser agrees to assume all liability for damages and/or bodily injury by the purchaser or any other person and to hold Cinematronics, Inc. harmless from liability or claims arising from the use of the goods by any person. Purchaser further agrees to indemnify Cinematronics, Inc. from any liability, claim, cause of action or litigation resulting from the use or misuse of the goods by any person.

Parts returned for warranty service must be packaged so that no damage is incurred during the shipment. Full documentation and instructions must accompany returned parts. Parts must be shipped prepaid to:

Cinematronics, Inc. 1466 Pioneer Way El Cajon, Calif. 92020

Page 5

CUSTOMER SERVICE PROCEDURES

It is the desire of Cinematronics, Inc. to provide efficient and courteous service should the need arise. We have a fully staffed Customer Service Department and encourage you to call our toll free number: 800-854-6577 ,78, for technical assistance between the hours of 7:00 A.M. and 5:00 P.M., California time, Monday through Friday.

In order to provide the very best service possible, the following procedures for ordering or returning parts must be followed:

  • All equipment ordered from Customer Service, whether in or out of Warranty, must be placed with a Distributor’s purchase order, either by mail or verbally by telephone.
  • Advance replacement items may be obtained only during the term of the Warranty and when such items are available, using the same procedure as when ordering parts. When ordering a PCB, please include with your order the game serial number and the number of the PCB you wish replaced.
  • All items received as advance replacements will, after a period of thirty (30) days, become the property of the Distributor, with applicable charges applied in the event Customer Service has not received the defective item against which the advance replacement was made.
  • The Distributor must call this facility for an RMA number prior to returning any item. Please be prepared to provide us with the game serial number and the PCB number when requesting an RMA.
  • In all situations covered above, and in all other situations, the Warranty offered by Cinematronics, Inc. is appicable and should be fully understood.
  • Parts returned for service must be packaged so that no damage is incurred during the shipment. Cartons without a prominently displayed RMA number will not be accepted. Full documentation including game serial number. PCB number and reason for return must accompany parts. Ship prepaid to:

Cinematronics, Inc. Customer Service Department 1466 Pioneer Way El Cajon, CA 92020

800-854-6577 714-440-2933

Page 6

SECTION 1

INTRODUCTION

Page 7

Section

an an Bw TABLE OF CONTENTS

INTRODUCTION 2.00. occ cece tect e ene

INSTALLATION ... 1.0.0. etree neeneee

GENERAL INFORMATION .......... 0.00060 bee e eee e eee e tee eee

VECTOR THEORY

THEORY OF OPERATION .......-. 2000000200 cee eee eee tenes

MAINTENANCE ........ 20.002 eee eee tenet tenets

PARTSLISTS ..2 2.06.00 cece cee center e ee

APPENDIXA — Assembly Drawings. Schematics & Wiring Diagrams

Table

5-1

6-1 LIST OF ILLUSTRATIONS

Title

Graphical Representation of a Matrix . . Line using Vector System ........... Non-linear Charging Voltages

Functional Block Diagram Detailed Block Diagram ...... Audio Board Block Diagram

LIST OF TABLES

Title

Operation Option Switch Positions .......... 0.060 c cece ete cents

Block Numbers and Component I.C. ...

Troubleshooting Guide .........00 0000. c cee cee eee eee eee e teens Page

1-1

3-1

4-1

5-1

6-1

7-1

Page

2-2

5-9

6-1

Page 8

SECTION 2

INSTALLATION

Page 9

INTRODUCTION

Tailgunner is a one player game with dual controls providing ease of operation for right and left handed players. The video display generates 2 levels of intensity, and the audio system generates 6 different sounds during play. The player has control over a moveable sight on the screen by means of a proportional joystick control, which is used for aiming at oncoming spacecraft as they appear on screen. The player has control, by means of a fire button, over a Phasor cannon which, when depressed causes two energy bursts, originating from the bottom corners of the screen, to intersect at the current location of the moveable sight and destroy enemy spacecraft. The player also has control of an energy force shield. When this is activated, it appears on the screen and prevents any enemy spacecraft from passing by. Shield time counts down as used (at the rate of 5 units per second), and once the shield energy reaches zero the shield cannot be reactivated and the player must rely on his skill at destroying ships with his Phasor cannons to prevent any ships from passing by. As soon as ten enemy spacecraft have passed off screen, the game is over. Spacecraft enter the screen in groups of three, and until all three have either been destroyed by Phasor fire or passed off screen, another group will not enter. As more ships are destroyed, the succeeding groups become more evasive and move faster. After inserting the necessary amount of money (one or two coins), 1 credit will be displayed on the screen, and when the start button is depressed the game begins. The amount of shield energy can be changed by switches on the CPU Board, as can the amount of coins per credit.

Page 10

SECTION 2

INSTALLATION

RECEIVING INSPECTION Your game was shipped in ready-to-play condition. However, after removal of the shipping carton, a brief visual examination is suggested.

Naturally, you’ll want to make note of any physical damage to the game cabinet and its external components for freight claim purposes. Considering the quality of the shipping carton, any damage to the exterior would indicate possible interior damage as well.

The ‘‘guts’’ of the game should also undergo a brief examination for: loose mounting hardware (check to be sure that the major components are still securely mounted); disconnected or loose wires, cables or harnesses; electronic devices loose in their sockets; etc.

At this time the game serial number should be logged. Please remember that the game serial number will be required if you need service from your distributor.

ELECTRICAL REQUIREMENTS

Unless specified otherwise, your game was shipped to operate at 115 VAC, 50/60 Hz. Two other voltage settings are possible. The power supply chassis has a table which shows the voltage options and fusing requirements.

A good earth ground is essential for the

2-1 proper operation of this game or for that matter any electronic device. Problems with instability and erratic operation of computertype devices can usually be traced to an ineffective ground system.

INITIAL ADJUSTMENTS

NOTE

When the game is connected to AC power, one of the game sounds may be heard. This is normal.

The audio level (volume) can be easily adjusted and THIS IS ACHIEVED BY ROTA- TION OF THE ONLY CONTROL ON THE AUDIO CIRCUIT BOARD. The audio level should compete with other machines ‘‘on the floor’’ to maximize play time.

Display brightness is another easy adjustment. The monitor assembly has several adjustments, but the brightness control is the only one which does not require a “‘screwdriver’’ for rotation. Keep the brightness at the correct level for appeal.

OPERATOR OPTIONS

The option switch is located on the logic or game board. It is not necessary to remove the board from the cabinet to set the options. In fact, the option switch and audio control can be reached easily through the coin door opening. Table 2-1 will assist you with your selections:

Page 11

The following chart diagrams the switch settings of the option

switches for ‘‘TAILGUNNER’’. LOGIC BOARD OPTION SELECT TABLE

position E-2 on the logic board. The 7 station switch is located at

OPTIONS: SWITCHES SHIELD POINTS Coins Per Credit 15 20 30 40 50 60 70 80 Switch #1 ON | ON | OFF] OFF | ON | ON | OFF | OFF x x

Switch #2 ON | OFF} ON | OFF{ ON | OFF] ON | OFF xX x

Switch #3 xX xX X xX xX OFF ON Switch #4 xX xX x

Switch #5 x x Xx

Switch #6 ON | ON | ON ON | OFF | OFF | OFF | OFF xX x Switch #7 x xX xX xX x x x xX xX xX

NOTE

ON = CLOSED = LOGIC 0

OFF = OPEN = LOGIC 1

X = NO EFFECT

2-2

Page 12

SECTION 3

GENERAL INFORMATION

Page 13

SECTION 3

GENERAL INFORMATION

Your Cinematronics game is designed much the same as conventional video games. The major exception is the use of an alternate means of visual display the patented Vectorbeam *m” monitoring system.

However, the game is built of the same basic building blocks as any other video game:

The Power Supply provides all necessary voltages for each separate electronic assembly as well as the AC lighting required throughout the game.

The Central Processing Unit contains circuitry to strobe and interpret all input functions which include the player control panel switches and all coin. and credit information and generates all the digital signals used to provide the visual display and control the audio effects. It also contains all the software (i.e, machine language and game personality memory) needed to control the game operation and to generate the proper vectors for the display.

The Audio Board consists of a noise generator and wave shaping circuits which produce different game sounds on command from the CPU logic board.

The Vectorbeam tm" Display Electronics is the final form of interpretation of the CPU’s calculations. The CPU logic informs the display electronics unit of information regarding line length and line placement on the CRT. This is accomplished withtwotwelve-bit words each for horizontal and vertical deflection, and a number of other controlling signals for the cathode drive circuit and switching of the deflection circuits.

3-1 The major difference between the vector generator and raster scan type monitors is the means by which the cathode beam is directed (deflection) across the screen.

In the raster scan type of display, the electron beam from the cathode to the anode of the CRT is constantly deflected (scanned) across the face of the CRT in a series of horizontal lines that trace from the upper portion of the screen to the bottom in a synchronous pattern. Vertical information is forming a matrix-type pattern of mathematically possible illumination points on the face of the CRT. If the cathode current is increased at these points on the screen in matrix-type patterns (similar to placing dots on a piece of graph paper where the lines intersect) coherent video in the form of shapes and alpha-numerics to form game backgrounds can be displayed.

The vector generator takes a slightly different approach to cathode beam deflection. The results are a much higher degree of resolution and much smoother motion across the screen. Rather than using a constantly scanning cathode beam, the beam is directed only to points of eventual illumination, using a vectoring form of programming rather than a matrix approach. Basically, the cathode beam is directed between two determined points, and illuminates the entire path of phosphors between these two points, unless blanked by stopping cathode current (i.e., when the beam moves from one star to another on your screen). The ability to illuminate the entire path of phosphors crossed by the electron beam, in any direction desired, (which is not possible in a raster scan system) creates a

Page 14

much higher degree of resolution than can be found in a raster scan system while ait the same time creating a much greater number of angle possibilities. This is also supported by the ability to accommodate two twelve-bit words of information, twelve each for vertical and horizontal deflection, and the fact that there is no background illumination from a constantly scanning beam when brightness is turned up. The higher degree of resolution

“Vectorbeam tm” is Cinematronic’s service mark for video game repair and education services. combines with the totally blackened background generating an appearance of depth not found in a raster scan system.

Another major design difference is the fact that no sync. signals are needed to produce vectors on the CRT. This greatly simplifies the hardware design of the system, and therfore the understanding of the theory of operation, both the CPU logic and the display electronics.

Page 15

SECTION 4

VECTOR THEORY

Page 16

SECTION 4

VECTOR THEORY

In order to understand the basic concept behind a vector generated display, it is

important to have a basic knowledge of vector theory.

As mentioned in the general information section of this manual, the raster scan display uses a matrix type display pattern. A graphical representation of a matrix is shown in Figure 4-1.

For example, to produce a line on the CRT with a matrix-type pattern, the appropriate intersection points of horizontal and vertical lines are illuminated. The calculations which select these points are made on the logic board, and converted into video information for the monitor to digest. Although there are spaces between the illuminated points, the illusion of a solid line is made by your eyes, and the resolution is determined by the number of available horizontal and vertical lines in the system, and the speed of the sweep.

In the vector display system, there are no horizontal and vertical lines (no sweep) or sync. A line generated using a vector system is shown in Figure 4-2.

A line is drawn by programming a beginning and ending point of the line to be drawn, and forcing the cathode beam to travel between these two points, illuminating the entire path

4-1 of phosphorus on the CRT. The angle of the line, the position of the line, and the length of the line are determined simultaneously, and simply, by selecting the proper voltage levels for the beginning and ending points of the line.

This is accomplished by the two twelve-bit codes (words) applied to the DAC-80s on the display board. The DAC-80 will produce a different voltage level at its output for each possible combination of input levels (of which there are 4096 possiblities for each 12 bit word.)

It is also important to remember the function of the LF 13331 analog switch and its output RC network. Because we are dealing with reactive components in C101 and C201 on the display board the charging voltages found are non-linear by nature. (See figure 4-3.)

Therefore, when a line appears on the CRT, it is actually only part of the entire path taken between the beginning and ending points of the vector (C-D). The section of A-B is chosen as the most linear portion of the charge curve, and is illuminated.

Sections C-A and B-D are blanked at the cathode, and points A and B chosen by controlling the analog switch on the display board. These calculations are all performed on the CPU logic board.

Page 17

HORIZONTAL

+ +

a VERTICAL

Figure 4-1. Graphical Representation of a Matrix

ape

\Chargang|voltage furve of |capac{to: olltage

Current

Figure 4-3. Non-linear Charging Voltages

4-2

Page 18

(2x J-2) -2

=%

Figure 4-2. Line using Vector System

When a line appears on the CRT, it is actually only part (section A-B,) of the entire path taken between the beginning and ending points of the vector (section C-D). Section A-B is chosen as the most linear portion of the charge curve, and illuminated.

Sections C-A and B-D are blanked at the cathode, and points A and B chosen by controlling the analog switch (V-1) on the display board. Again, these calculations are all performed on the CPU logic board.

Page 19

SECTION 5

THEORY OF OPERATION

Page 20

SECTION 5

THEORY OF OPERATION

GENERAL DESCRIPTION

This section describes the principles of operation of the major circuit functions of the Cinematronics Video Arcade Game. The system’s general functional description is followed by detailed circuit schematics which are included as Appendix A. The schematics used in this manual are similar in nature to those used by most industrial electronic firms.

MONITOR DISPLAY The Vectorbeam tM monitor is unlike the conventional TV monitor in that it displays vectors (lines) generated from X-Y coordinates recieved from the logic board. The horizontal points are X (width) and the vertical points are Y (length). The X and Y logic signals originate from the logic board.

The Vectorbeam t™ monitor can be divided into two basic sections: one is the deflection amplifier and the other is the voltage and cathode drive circuits.

The deflection amplifier can be further divided into two identical channels: one for the vertical deflection and one for the horizontal deflection. The operation of the vertical channel will be discussed; however, the same theory of operation pertains to the horizontal channel.

Digital information, in the form of a twelve-bit word, is applied to the input of the DAC-80 digital to analog converter (U101) on Pins one through twelve. The most significant bit is applied to pin one, and the least significant bit is applied to pin twelve. The DAC-80 makes the necessary conversion from digital signals to analog signals which are outputted as analog voltage signals on pin fifteen (proportional in level depending on the input word applied). The result is a positive and negative voltage signal about its reference

5-1 voltage. Remember, there is no ‘‘sync’’ signal present, and the signal is not true video as seen in raster scan monitors.

From the DAC-80 the analog signal is then sent to a high-speed analog switch, (Ul). The analog switch has two parallel inputs for the display signal, and two controlling inputs which select one of two outputs from the switch. An R.C. network, which is used to create line length and line position on the screen is found at the outputs.

Output fifteen from the switch routes the analog signal through a 5K potentiometer (R102), a 10K resistor, (R103) and to the input of U102 op-amp. The time constant developed by these two resistors and the capacitor (C101) determine the length of the vector line seen on the screen. Adjusting the potentiometer will adjust the length of the vertical lines seen on the screen.

Output ten from the analog switch routes the signal directly to the input of U102 op-amp, and the resulting time constant of the op-amp input impendence and the capacitor C101 determines the position on the screen of the vector line.

Op-amp, U102, serves a dual purpose: it acts as a buffer between the deflection amplifiers and the analog switch, as well as an “‘edge gain’’ amplifier (i.e., height).

At the output of U102, there is a resistor diode network consisting of R105-R110, and CR101-CR104. This resistor diode network is used to compensate for the non-linear characteristics of the CRT near the edges of the screen. If this circuit were not used, any object displayed on the screen would increase in size as it moved closer to the edges of the screen. Potentiometer (R109), adjusts the height of the pictures

Page 21

From the wiper of R109, the signal proceeds to Q101, which is the first stage of deflection amplification. Q103 is emitter coupled with Q101 to provide a degenerative feedback loop from the yoke. Q102 is used to provide a constant current source to both emitters.

At this point, the deflection circuit can again be divided into two identical circuits. One circuit, which controls the lower half of the screen, is comprised of Q104, Q106, Q108, and Q110. The other circuit, which controls the upper half of the screen is comprised of Q105, Q107, Q109, and Q111. **

Q104, Q108 and Q110 are three stages of amplification, while Q106 is used as current limiting protection for Q108 and Q110. The same holds true for the other configuration of Q105, Q107, Q109 and Qill. R124 through R129 are used as a current divider network for the yoke.

R122, R123, and C102 form a RC network, which compensates for any counter EMF that may develop by the expanding and collapsing of the deflection coil’s electromagnetic field.

The high voltage and cathode circuitry is the second section of the monitor. This section also contains the necessary voltage regulation to power the ICs located on the display board as well as develop the high voltage.

U4 and U6 provide plus 15V and minus 15V respectively to power the DAC-80s and the TLO81 op-amps on the display board.

U3 and U5 provide plus 18V and minus 18V used in the high voltage transformer (T-1) and oscillator (the oscillator circuit is necessary because there is no horizontal sync. used to develop the high voltage pulses.) The oscillator circuit is comprised of primary windings, Q4 and associated discreet components.

5-2 The high voltage 18KV is developed by Tl secondary windings, and the high voltage tripler. ‘ The intensity and beam blanking control circuitry is composed of U7, Ql, Q2, Q3, Q8 and associated components. The cathode voltage rides at +88. The beam is turned on by a more negative voltage. At the anode of CR4 negative pulses can be seen, these are the beam on pulses. For normal intensity the pulses will go down to approximately 40V, for double intensity, 20V. Pins 3 and 4 of U7 is the normal intensity control gate which receives information from the CPU. Pin 1 and 2 is the double intensity control gate. When a Hi going Lo signal is on pin 3 of U7 pin 4 will be a Lo going Hi turning on Q3 on the Hi transition. Q3 acts as a switch connecting the series network of R11, R9 and R10 to ground creating a voltage divider network. Rll is the manual intensity control. When 2 of U7 goes Hi Qi turns on for the duration of the pulse connecting just R9 and R11 to ground, thus lowering the voltage at the anode of CR4 lower still because of the lower resistance, than with normal intensity. Q2 is used as a switch to enable Q1 and Q3. Its purpose is to shut off the beam when the power is turned off. Q8isa beam on delay to prevent phosphor burns if someone was to unplug and plug in the machine rapidly.

R111 is the brightness potentiometer, which adjusts the amplitude of the negative spikes used for brightness and intensification.

** In the horizontal section of the deflection amplifier, Q204, Q206, Q208 and Q210 control the left hand side of the screen, and Q205, Q207, Q209, and Q211 control the right hand side of the screen. By dividing the screen in this manner, four quadrants of deflection area have been developed (refer to Vector Generator description).

Page 22

CPU BOARD

The processor hardware can be broken down into five basic functional blocks as shown in Figure 5-1. The arrows indicate the possible data flow directions between the various blocks. The ALU and Control block are the main components of the processor while the Memory and I/O blocks may be thought of as merely peripherals. Figure 5-2 is a detailed block diagram of the processor. The numbers in each block correspond to the entries in Table 5-1, which lists the IC numbers of the main components of each functional block. The following is a brief description of each block shown in Figure 5-1. The numbers beside each functional block name are the numbers in Figure 5-2 which correspond to a particular function.

RAM (6)

The RAM is implemented with three read/write static memories configured as a 256 x 12 bit block. Data can be transferred to or from this memory via the ALU block. The processor uses this RAM as a scratch pad.

ROM (10)

The ROM is configured as an 8K x 8 bit block of memory. These memory locations contain the program instructions and/or data. It is accessed via the processor control unit.

1/0 19, 17, 18

The I/O block consists of 8 output lines implemented with a bit addressable latch, 24 input lines implemented with data selectors, and two 12 bit registors which are connected to the X Y display deflection circuits via D/A convertors.

Arithmetic Unit 1,2,3,4,5

The arithmetic unit performs all the arithmetic processing for the system. It consists primarily of two 12 bit accumulators, an arithmetic logic unit and various data selectors. The accumulators can function as temporary storage registers for arithmetic

5-3 functions upon the data in the accumulators. The data selectors are used to select the various sources of data which will be processed.

Control Unit (15,16,14,7,8,9,11,12,13)

The control unit is the heart of the processor. It performs all instruction decoding operations and generates all the necessary control signals which the rest of the hardware requires to function correctly.

The following is a discussion of each block shown in Figure 5-2.

  • Accumulator Selector

The accumulator selector consists of 3 quad data selectors. They are used to select the output of either the primary or secondary accumulator for processing by various other sections of the systems.

2 & 3 Primary and Secondary Accumulators

The two 12 bit accumulators are implemented with quad bidirectional shift registers. The primary accumulator consists of S4, P4. M4. The secondary accumulator consists of T4, R4, N4. All data manipulation in the processor is accomplished using these two accumulators. All output data flows through these registers.

  • Arithmetic Logic Unit (ALU)

The ALU is used to perform all necessary arithmetic functions within the processor. The ALU is implemented using three 24L5181 (N6M6L6) function generators, three 74LS85 (N9,M9,L9) 4 bit magnitude comparators, and a74S182 (L4) look ahead carry generator. The data which the ALU manipulates can come from four different sources. The first source is the contents of the accumulators via the accumulator selector. The second and third sources are the ROM and RAM data outputs via the ALU data selector (N11, M11, L11) and the fourth source is the external input selector (E4, D4, C4).

Page 23
  • Data Selector

The data selector is used to read data into the ALU from either the RAM or ROM memory. Note that the ROM data is only 8 bits wide while the RAM data is 12 bits wide.

  • RAM Storage

The system RAM consists of three 9101C high speed static memory chips connected as a 256 x 12 bit block. The block is 12 bits wide in order to allow the contents of an accumulator to be stored. The processor uses the RAM as temporary storage of program variables, data pointers or any other data of a dynamic nature.

  • RAM Address Selector/Register

The output of this register is tied directly to the address lines of the RAM. It consists of a multiplexer which routes address data from either the ROM or RAM locations to the RAM address lines. The capability to use RAM data to select RAM addresses is the basis for the indirect addressing mode of the processor.

  • Page Selector

The page selector is used to latch the high order 4 bits of a RAM access instructions.

  • ROM Data Register

The register is used to temporarily hold data from the ROM during an instruction fetch.

  • ROM Memory

The ROM memory consists of the actual memory chips plus a data selector and latch

5-4 circuit. The latch is used to improve the memory access time during a two byte instruction fetch by allowing one byte of the instruction to be latched while the RAM address lines are decoded for the other byte. The data selector can then be used to rapidly access both bytes of the instruction by switching between the latch and memory outputs.

  • Instruction Register

The instruction register is a latch which holds the current op code as read from ROM. Its output is tied to the instruction decode circuitry which in turn generates the necessary signals to execute the instruction.

  • System Sequencer.

The system sequencer is used to decode an instruction op code and to generate the appropriate timed sequence of signals which execute the instruction. The op code is decoded by using it as the address data to a set of decoder ROMS. The outputs of the decoder ROMS are then synchronized with the system clock and used to control the various system functional blocks.

  • Line Length Counter

The line length counter is used during the process of drawing a vector io control the length of a vector, by turning off the beam at a pre-determined time after the vector is intiated. The counter is loaded with a value from a line length ROM and then counts up until it overflows which in turn generates a signal to indicate the vector has been finished.

Page 24
  • Program Address Selector

This selector is used to provide the address data to the program ROM. It selects either the program address counter output or the accumulator selector output and routes this data to the ROM address lines. The ability to use the accumulator contents as address data allows the program to randomly access data tables stored in the ROM or to compute a branch address after a conditional test.

  • Program Address Counter

This is a 12 bit counter whose output defines the next location in ROM to be accessed. It is normally clocked sequentially to step through a program. However, it can be loaded with data from the program address register which is how the jump instructions are implemented.

  • Program Address-Register

This register is a latch used for temporary storage of an address which will be loaded into the program counter during a jump instruction. The input data to this latch can come from either the program ROM or the scratch-pad RAM.

  • Input Selector

The input selector is used to read the state of one of the 24 input lines into the selected accumulator. There are 16 primary inputs and 8 secondary inputs. During an input instruction the upper 11 bits of the accumulator are set to zero while the least significant bit reflects the state of the input line. All input lines have pull up resistors on them so that they will read high if they are left unconnected.

  • Output Selector

The output selector is a bit addressable latch used to control the 8 output lines. During an output instruction the selected output line is set to the complement of the least significant bit of the accumulator. The output lines are used to control the audio board, display intensity and the mechanical coin counter.

  • Display Registers

The display registers are the interface between the processor and the display driver circuits. These registers are latches into which the contents of the accumulators can be stored. The outputs are tied to D/A converters which provide the input voltage to the display deflection amplifiers.

AUDIO BOARD

The sound generation circuitry is composed of the following functional blocks: Audio Power Amp with volume control, Explosion sound, Wideband Noise Generator, Background Rumble, Force Shield Hum, Shield Bounce, Hyperspace, and Phasor Cannon sound. All discrete sounds are tied together at a summing junction and then fed to R70 (The input to the power amp). Each sound is triggered by a low going digital pulse from the trigger port (IC23), which is software controlled by the CPU Board.

FUNCTIONAL BLOCKS

Each functional block is listed on $D205200 by its functional name (Example: Explosion). The Power Amplifier is composed of 1C19, Q6, Q7, R75 and their associated components. IC19 is a preamplifier which directly feeds the push-pull power amp, Q7 and Q6. Adjusting R75 will change the amount of feedback to the preamp causing an increase or decrease in volume at the speaker. Under no circumsiances should the Power Amplifier drive a speaker of less than 8 ohms impedance.

The Wideband Noise Generator is a common signal source for providing wideband random noise to the discrete audio sections of the board. The noise generator works as follows: diode D1 is a zener diode with random noise levels of typically 200 micro volts generated at its internal junction. This noise will be present at the anode of D1 across resistor R1. The noise is amplified by a factor of 1000 by IC1 and coupled to IC2. IC2 is a band equalizing signal limiter which will balance out the amplitude of the noise frequencies by amplifying the weaker signals

Page 25

and attenuating the stronger signals. The output of IC2 should appear as wideband clipped noise with an amplitude of 1.2 volts peak to peak. IC3 will amplify the noise to approximately 5 volts peak to peak at which time it is ready for use by the sound circuits.

The Explosion sound functions as follows: Wideband noise is filtered by IC9, which is an op amp integrator, and injected into pin 2 of 1C10. A negative going pulse of approximately 400 ns from pin 4 of IC23 fires a one shot,IC12. The output of IC12 then goes to 5 volts for a time determined by the RC time constant of C15 & R39. This brings Q3 into conduction charging C16 to + 5 volts, turning on IC10. Once the pulse from IC12 has ended, C16 will discharge to minus 15 volts causing decaying explosion sound as IC10’s output amplitude fades.

The Background Rumble sound utilizes the explosion circuit just explained. By maintaining a low level output from the trigger port on pin 5 of 1C6, Q5 is kept in conduction causing IC10 to conduct at a low level of amplification, which is determined by the value of R43. This allows a low amplitude level of noise to be constantly heard at the speaker.

The Shield Hum sound is composed of two 555 square wave oscillators IC16 and IC17. The output of each oscillator is fed into a RC filter network where the square wave is converted into a sinusoidal waveform. The outputs are then combined at pin 2 of 1C13. Whenever pin 13 of IC4 goes to a low logic level, Q5 conducts turning on IC13 at an amplitude level determined by the value of R47 until pin 13 of IC4 goes back to a high logic level.

The Shield Bounce sound functions in nearly the same manner as Shield Hum. Two 555 oscillators feed 5 volt square waves into their

5-6 corresponding dividers IC18. Then the outputs are combined at pin 2 of IC22. Filtered wideband noise is also injected at pin 2 of IC22. IC12 is a one shot which is triggered from IC23. When pin 12 goes to a low level, Q8 conducts charging C44 to + 5 volts and turning on IC22. When the one shot resets it turns off Q8. C44 then discharges to minus 15 volts creating a decaying envelope out of 1C22.

The Phasor sound is created by ramping a VCO (iC11), from a high frequency to a low frequency while feeding the signal into a divider (IC8). When pin 4 of IC4 goes toa low level, pin 6 goes low enabling 1/2 of IC8. At this time pin 4 of IC6 goes from its low state enabling C13 to charge, which changes the voltage at pin 3 of IC11 causing the frequency shift. The output signal is then converted to a 5 volt sqare wave by Ql and fed into IC8 through IC5. The digital outputs of IC8 are fed into R35-38 and R21, R22, and C8 converting them into an analog signal. When pin 4 of IC4 returns to a high logic level, IC8 is disabled permitting no sound out and C13 is grounded through IC6 causing the VCO to return to its highest frequency.

The Hyperspace sound is created in the same way as the Phasor sound except that instead of low frequency sweep it goes from a low to a high frequency. When pin 1 of IC4 goes low, pin 3 goes low, enabling 1/2 of IC8. Pin 6 of IC5 goes high and pin 2 of IC6 goes low discharging C6 which sweeps the VCO. The rest of the circuitry is identical to the Phasor sound.

The Trigger port is an 8 bit addressable latch whose inputs come from the output latch on the main logic board through a ribbon cable to J4. The outputs of IC23 are at a high level until the proper commands are received from the CPU board. Ail sounds are low level actuated.

Page 26

ARITHMETIC UNIT

Figure 5-1. Functional Block Diagram

5-7

Page 27

DATA

SELECTOR

2) © RAM

STORAGE

T | Es ©

RAM ADDRESS

SELECTOR & — fagg——————_} SELECTOR REGISTER (0)

PAGE

ROM DATA

© Figure 5-2. Detailed Block Diagram "ACCUM. DISPLAY SELECTOR REGISTER |} 70 ) DISPLAY PRIMARY SECONDARY ‘ADDRESS ‘ADDRESS ‘ADDRESS LINE ACCUM. Oo Jig J Accum O —pee} REGISTER @ J | COUNTER © |__| SELECTOR @ ER re)

FROM To GAME GAME ‘ARITHMETIC | SYSTEM UNIT ge] SEQUENCER

INPUT OUTPUT t SELECTOR SELECTOR

REGISTER INSTRUCTION 2) ROM REGISTER = Poug————__—___-] MEMORY

5-8

Page 28

10.

11.

12.

13.

14.

15.

16.

17.

18.

19. TABLE 5-1. BLOCK NUMBERS AND COMPONENT I.C.

T-2, R-2, N-2

S-4, P-4, M-4

T-4, R-4, N-4

N-6, M-6, L-6, N-9, M-9, L-9

N-11, M-11, L-11

N-14, M-14, L-14

J-12, 1-12

H-12

S-13

U-7, R-7, T-7, P-7, U-9, T-9, U-11, T-11

T-13

A-8, G-10, F-10, G-14, F-14, E-14, D-14, C-14

E-6, D-6, E-8, H-8, G-8, F-8

S-9, R-9, P-9

$-11, R-11, P-11

P-13, R-13

E-4, D-4, C-4

F-2

$-2, R-2, M-2

5-9

Page 29

FROM’ TRIGGER

CPU

PORT

A LS259

LI ENABLE

EXPLOSION

SUMMING

NETWORK

l SIGNAL

PROCESSING

RUMBLE ENABLE SHIELD. HUM ENABLE

CONTROL PRE AMP I ! ! \ SHIELD BOUNCE ENABLE!

POWER Lo=On

ENABLE |

AMP op PHASOR ENABLE

FEEDBACK VOLUME CONTROL AUDIO BOARD BLOCK DIAGRAM

OUTPUT ° 5-1

Page 30

JOYSTICK CONTROL CIRCUITRY

The Joystick circuitry is used in conjunction with the CPU Board to perform an analog to digital conversion. The X & Y pots on the joystick control work in the same manner with identical circuitry. One end of each pot is connected to +15 and the other end to -15V. The center wiper of each pot goes to its corresponding circuitry. The voltage off the pot is fed into the input of a noninverting DC amp, the capacitors on the input are used to smooth out the response when moving the joystick quickly to prevent jerkiness, then into a comparator. The other input to the comparator comes from the horizontal digital to analog converter on the display board. The

5-11 comparator is comparing these two signals and feeding them back into the CPU. The 7406 is being controlled by the CPU to select either the X or the Y signals. The CPU reads the signal from the comparators. For example; take the vertical pot; if the joystick is moved left, the voltage changes and is compared with the output of the DAC, which reflects the actual location of the sight on the screen. Then the comparator reflects the difference and feeds it to the CPU, which then reads this change and outputs to the display beard a new location for the sight, in proportion to the speed and location of the pots on the joystick control. This new location is fed back to the comparator on the joystick circuitry and compared again until location matches the position of the joystick control.

Page 31

BLOCK DIAGRAM JOYSTICK CONTROL CIRCUITRY

X D CAMP

HORIZONTAL POT (JOYSTICK) X COMPARATOR

HORIZONTAL PAC DISPLAY BD.

VERTICAL POT (OYSTICK) X-Y SELECT

Y COMPARATOR —P>

Y COMPARATOR CPU BOARD

5-12

Page 32

SECTION 6

MAINTENANCE

Page 33

TABLE 6-1. TROUBLESHOOTING GUIDE

PROBLEM PROBABLE SOLUTIONS

No picture

Narrow line on display

Half of picture missing Listen for audible ‘‘clatter’’ from the Vector circuitry on the display board. If the clatter is present, then the DAC’s and the analog switch (LF13331) are operational and the problem is in the intensity circuitry.

If game audio is present, the problem is in the monitor. If the audio is distorted or absent, the problem is usually on the logic board. Check IC F-2 pins 4, 5, 6, 7,9 & 12.

Check the neck of the CRT for a glowing filament. If there is no glow check the black and brown wires of the CRT connector for 6.3 VAC between them. Check IC C-8 pin 6 on the CPU with a logic probe. Pin 6 should be low indicating that the CPU is not continuously resetting.

Be sure all connections are made to the display board and CPU.

Connect a scope to the yellow wire leading to the CRT connector. Set brightness full clockwise. There should be data pulses of 50 volts P-P at an 80-100 volt base. If no data pulses are present, connect a scope probe to pin 2 of IC U7 and check for data pulses. If data is present, check Q1 and Q2 with an ohmeter or a transistor tester.

Check J2 pin 14 for +25 volts unfiltered.

Check CRT neck for broken pins or other damage.

Check the seating of the CRT plug and insure that proper connections are being made.

Check for an open winding in the yoke coils.

Check for bad connections of yoke wires to display board.

Check for continuity between display board and power transistor on heat sinks Q110, Q111, Q210. and Q211. Check for faulty power transistors Q110, Q111, Q210 and Q2211. Also check for broken solder connections on circuit board molex connector socket pins.

Left half: Check Q208, Q206, Q210 Right half: Check Q209, Q207, Q211 Top half: Check Q109, Q107, Q111 Bottom half: Q108, Q106, Q110

6-1

Page 34

TABLE 6-1. TROUBLESHOOTING GUIDE (Continued)

PROBLEM PROBABLE SOLUTIONS

No high voltage On display board, check DC voltage output of IC U3. It should be +18 volts DC. If not present, check for +25 volts present at the input to U3.

Check DC voltage output of IC U5. It should be -18 volts DC. If not present, check for -25 volts present at the input to U5.

Lift the winding from pin 3 of the high voltage XFMR Tl. Measure +18 volts. If the +18 volts is present, check for a shorted Q4, shorted capacitors C20, and C19, bad diodes CR7, and CR8.

Check for 6 kilovolts at black wire of XFMR T1.

Dotted display Check for faulty analog switch U1. Inspect yoke connections to display board. Check for open yoke windings. Check for proper +25 and -25 volts DC. Check operation of DACS U101 and U201.

No audio sound Check for an open speaker coil. Check transistors 2N6292 and 2N6107 and other nearby output components on audio board with an ohmeter or transistor tester.

Check for open wiper on volume control of audio board.

Verify that CPU is fully operational.

Coin counter is Check transistor 2N6292 on logic PCB with ohmeter or transistor inoperative tester.

Disconnect coin counter molex connector. Measure DC voltage on red wire. Meter should read +25 volts DC.

Check power connector (J1) to logic board.

Check electrical connection at pin 3 to J1.

6-3

Page 35

TABLE 6-1. TROUBLESHOOTING GUIDE (Continued)

PROBLEM PROBABLE SOLUTIONS

No brightness control

Circuit Breakers Trip

Picture on display jitters Check intensity pot R11 for open wiper or internal short. Check for open capacitor C17. Check for bad solder connections to R11.

Disconnect power to display board. If circuit breakers continue to blow, check for a shorted speaker coil. Verify that the + 15 and -15 volt regulators are operating properly. Verify that the output power transistors on the audio board are good with an ohmeter or a transistor tester.

Check IC C-8 pin 6 on the CPU with a logic probe. Pin 6 should be low indicating that the CPU is not in continuous reset. Measure the voltage at IC T-13 pins 10 and 20 with an accurate voltmeter. The meter should read between 4.8 and 5.1 volts DC for normal system operation.

Remove connectors J3 and J4 on the display board and check power transistors Q110, Q111, Q210, and Q211 located on the heatsinks with an ohmeter or transistor tester. Check diodes CR12 and CR15 located on the display circuit board.

Disconnect the CRT yoke wires from the display board and remove CRT socket. Re-apply power to the display board and reset circuit breakers if necessary. If the breakers do not blow then check transistors Q208, Q209 and Q204 in the horizonal deflection circuit and transistors Q108, Q109, and Q104 in the vertical deflection circuit with an ohmeter ot transistor tester.

Check the horizonal and vertical DACS for proper supply voltages at pins 13, 14, and 22.

Measure outputs of amplifiers U102 and U202 with a scope for A+2 volt P-P signal centered at zero volts.

Check the vertical size adjustment R109 for wiper noise by turning the wiper briskly while observing the screen. Then readjust for proper screen size.

Check for bad solder connections on R109.

Repeat the above two steps for horizonal size adjustment R209.

Check DAC U201 and U101 for bad solder connections.

Check all molex connectors for good connections.

Check analog switch Ul for faulty operation, loose connections to socket or poor solder connections.

6-2

Page 36

os AUXILLARY CONTROL PCB ASSEMBLY PL205204

T ITEM NUMBER DESCRIPTION P, AEN. QTY

11 T-18R Ty Wraps 2 12 ref WL205204-1] Wire #1 1 13 ref WL205204-2| Wire #2 1 14 ref WL205204-3| Wire #3 1

COIN METER ASSEMBLY

PL205404

1 Coin Meter E2B65D 1 2 Diode IN4003 1 3 Molex Connector 03-09-2038 1 4 Molex Pins, Fem. 02-09-1118 2

COIN DOOR ASSEMBLY

PL205601

1 2165 Coin Door 1 2 Lock Assy. 1 3 Coin Mechanisms 2 4 3/16” x 1%2”’ Carriage Blt. Blk. Ox. 12 5 #10 InternalTooth Lk. Washer 12 6 #10 x 24 Hex Nuts 12 7 Ya’? Cable Clamps 2

2081 POWER SUPPLY HARNESS

PL205410

1 Molex Connector Display Board 03-09-2153 1 2 Molex Conn-Logic Bd., Power Supply 03-04-1122 2 3 Molex Connector Audio Board 03-09-1093 1 4 Molex Connector Coin Meter 03-09-1038 1 5 Molex Pins, Female 02-09-1118 23 6 Molex Pins, Male 02-09-2118 15 7 Cable ties T-18R 20 8 Speaker Term. Lugs 2 9 Molex Conn. Power Supply AC 03-09-1041 1

7-4

Page 37

A/C CORD ASSEMBLY

PL205408

PART MFGR. ITEM NUMBER DESCRIPTION PART NO. QTY

1 Power Cord 54-17238 1 2 #16 Spade Lug C10-401-P 3

LOGIC BOARD ASSEMBLY

PL205201

1 37-25LS181 IC, ALU 3 2 37-74LS00 IC, Nand Gate 4 3 37-74LS02 IC, Nor Gate 4 4 37-74LS04 IC, Hex Inverter 3 5 37-74LS08 IC, And Gate 2 6 37-74LS10 IC, Nand Gate 3 7 37-74LS27 IC, Nor Gate 3 8 37-74LS32 IC, Or Gate 4 9 37-74LS75 IC, Quad D Latch 2 10 37-74LS85 IC, Mag, Comparator 3 1l 37-74LS86 IC, Exclusive Or 1 12 37-74LS107 IC, Dual J-K Flop 7 13 37-74LS151 IC, 10F8 Multiplier 4 14 37-74LS157 IC, Quad Data Sel. 8 15 37-74LS163 IC, Binary Counter 9 16 37-74LS164 IC, 8 Bit Shift Reg. 1 7 37-74LS194 IC, 4 Bit Shift Reg. 9 18 37-74LS257 IC, Tri-State Quad. 3 19 37-74LS259 IC, 8 Bit Latch 1 20 37-74LS298 IC, Quad Mux 2 21 37-74LS377 IC, Octal D Flop 6 22 37-74LS393 IC, Dual 4 Bit Counter 2 23 37-74S00 IC, Nand Gate 1 24 37-74S02 IC, Nor Gate 1 25 37-74S04 IC, Hex Inverter 2 26 37-74S08 IC, And Gate 1 27 37-74S32 IC, Or Gate 2 28 37-74S113 IC, Dual JK Flop 2 29 37-74S158 IC, Quad Mux. 1 30 37-74S182 IC, Look Ahead Carry 1 31 37-7425 IC, Nor Gate 1 32 37-74265 IC, Output Buffer 1 33 37-2101A2 IC, Ram 256 x 4 3 34 2085 IC, Prom Drom 1 1 35 2086 IC, Prom Drom 2 1 36 2087 IC, Prom Drom 3 1 37 2088 IC, Prom Drom 4 1 38 2089 IC, Prom Drom 5 1 39 2090 IC, Prom Drom 6 1 40 37-74S10 IC, Nand Gate 1

7-5

Page 38

LOGIC BOARD ASSEMBLY PL205201

PART MFGR. ITEM NUMBER DESCRIPTION PART NO. QTY 41 $W205001 Masked ROM 1 42 $W205002 Masked ROM 1 43 7 Pole Dip. Switch JS8722-07 1 44 Crystal,20.0 mhz MP200CTS 1 45 IN914B Diode IN914B 2 46 Transistor 2N3904 2 47 Transistor 2N6292 1 48 Molex, Conn, 12 Pin 09-18-5127 1 49 Ansley Conn. 16 Pin 609-1622M 1 50 Ansley Conn. 26 Pin 609-2622M 1 51 Ansley Conn. 34 Pin 609-3422 1 52 14 Pin Socket CA14S10SD 1 53 16 Pin Socket CA16S10SD | 2 54 2076B Circuit Board 1 55 10-5331 330 Yaw 5% C 2 56 10-5471 470 Yaw 5% C 1 57 | 10-5102 1K %4w 5% C 12 58 10-5222 2.2K Yaw 5% C 1 59 10-5103 10K Yaw 5% C 2 60 10-5303 30K Yaw 5% C 1 61 10-5564 560K tw 5% C 62 19-002 1K Res. Dip. Pak D16-15-2-1K 63 27-050-024 Cap. .02uf 50V Disc 64 27-101-681 Cap. 680pf 100V Disc 65 23-350-330 Cap. 3.3uf 35V Tant. 66 23-350-331 Cap. 33uf 35V Tant 67 Test Points K27C 68 16 Pin Jumpers 435704-8

DISPLAY ASSEMBLY (MONITOR)

PL205403

1 19VARP4 CRT 19” 1 2 $A205405 Heatsink Assy. lref 3 $A205409 Display Sub-Assy. lref 4 LF13331 Analog Switch 1 5 $A205406 Yoke Assembly lref 6 2105B High Voltage Cage 1 7 171C Spring 1 8 #10-1/2”’ Flat Washer 4 9 #10-1"’ Fender Washer 4 10 #10-1”’ Hex Hd. Sms. 4 11 2136 Label-High Voltage 1 12 2137 Label-Factory Adj. Only 1 13 3064 #6 x ¥/’’ Hex Head S.M.S. ii

7-6

Page 39

DISPLAY ASSEMBLY (MONITOR) PL205403

PART MFGR. ITEM NUMBER DESCRIPTION PART NO. QTY

14 3066 #6 Lock Washer Int. 3 15 3063 6-32 x 12’ M.S. 3 16 3065 6-32 Hex Nut 3 17 21694 Mounting Brkt. LH 1 18 2170A Mounting Brkt. RH 1

DISPLAY BOARD ASSEMBLY

PL205203

1 10-5101 Res. 100 ohm Yaw 5% Car. 4 2 10-5102 Res. 1K Yaw 5% Carbon 2 3 10-5103 Res. 10K Y4w 5% Carbon 4 4 10-5150 Res. 15 ohm Yaw 5% Car. 2 5 10-5182 Res. 1.8K Yaw 5% Carbon 1 6 10-5201 Res. 200 ohm 1/4w 5% Car. 2 7 10-5222 Res. 2.2K Yaw 5% Carbon 2 8 10-5302 Res. 3K Yaw 5% Carbon 3 9 10-5330 Res. 33 ohm Yaw 5% Car. 2 10 10-5331 Res. 330 ohm Yaw 5% Carbon 1 11 10-5470 Res. 47 ohm 14w 5% Car. 6 12 10-5471 Res. 470 ohm aw 5% Car. 4 13 10-5562 Res. 5.6K 44w 5% Carbon 3 14 10-5682 Res. 6.8K Yaw 5% Carbon 1 15 10-5821 Res. 820 ohm Yaw 5% Car. 2 16 11-5103 Res. 10K 4/w 5% Carbon 2 17 11-5122 Res. 1.2K ¥/w 5% Carbon 2 18 11-5470 Res. 47 ohm 1/2w 5% Car. 4 19 11-5475 Res. 4.7M ‘/ew 5% Car. 1 20 11-5822 Res. 8.2K '/w 5% Carbon 4 21 12-5103 Res. 10K lw 5% Carbon 3 22 12-5270 Res. 2.7 ohm lw 5% Car. 12 23 12-5361 Res. 360 ohm 1w 5% Car. 2 24 Res. 100 ohm 2w 5% Car. 1 25 Res. 150 ohm 4w 5% Car. 2 26 Res. .18 ohm 3w 5% Car. 4 27 Res. 500 ohm 8w 5% Car. 1 28 Res. 1.43K Metal Film 1% 1 29 Res. 2.1K Metal Film 1% 1 30 Res. 10K Metal Film 1% 2 31 19-311101 Res. 100 ohm Trimpot 3386-P1-101| 2 32 19-413502 Res. 5K Trimpot 3386-P-1-502} 2 33 31-IN914B Diode IN914B 10 34 | 31-IN4003 Diode IN4003 36 35 31-MR818 Diode MR818 Fast Rec. 2 36 31-MR250-2 Diode, Fast Recovery MR-250-2 1

7-7

Page 40

DISPLAY BOARD ASSEMBLY PL205203

PART MFGR. ITEM NUMBER DESCRIPTION PART NO, QTY

37 37-7406 I.C. Hex Inverter O.C. 1 38 37-7815 I.C. +15V Regulator 1 39 37-7818 I.C. +18V Regulator 1 40 37-7915 1.C. -15V Regulator 1 41 37-7918 1.C. -18V Regulator 1 42 37-TLO81 1.C. TLO81 OP Amp. 2 43 37-DAC80 Digital to Analog Conv. 2 44 33-2N2102 Transistor 4 45 33-2N3904 Transistor 3 46 33-2N3906 Transistor 2 47 33-2N5210 Transistor 7 48 33-2N5320 Transistor 2 49 33-2N5322 Transistor 4 50 33-2N5550 Transistor 1 51 33-T1P41C Transistor 1 52 41-3006 Choke 100MH 2A Miller 5250 1 53 03-09-1152 Connector Housing Molex 1 54 02-09-2134 Pins Male Solder Tail Molex 8 55 09-18-5061 Connector Molex Wafercon Molex 2 56 609-3422-M Connector 34 Pin Ansley 1 57 2071E Etch Board 1 58 23-350-024 Cap. .02 35V 1 | 59 23-350-104 Cap. .1 35V 1 60 23-350-470 Cap. 4.7 35V 1 61 23-350-220 Cap. 2.2 35V Tant 4 62 24-101-106 Cap. 10 MFD 100V Axial 1 63 24-101-505 Cap. 5MFD 100V Axial 1 64 24-151-106 Cap. 10MFD 150V Axial 1 65 24-500-476 Cap. 47MFD 50V 5 66 24-500-506 Cap. 50MFD 50V 1 67 24-601-104 Cap. .IMFD 600V 1 68 27-050-104 Cap. .IMFD Disc 50V 2 69 27-050-474 Cap. .47MFD 50V 2 70 27-050-503 Cap. .005MFD Disc. 2 71 29-024-224 Cap. .022MFD 200V 2 72 Cap. .IMFD 100V 7 73 CA16S10SD 16 Pin Socket 1 74 37-7805 1.C. 7805 +5V 1

YOKE ASSEMBLY PL205406

1 746 Yoke, Broy 1 2 03-09-1063 Molex Connector 1 3 02-09-1118 Molex Pins-Female 3 4 02-09-2118 Molex Pins-Male 1

7-8

Page 41

MONITOR HEATSINK ASSEMBLY PL205405

PART MFGR.

ITEM NUMBER DESCRIPTION PART NO. QTY

1 2107-A Heat Sink 2 2 Transistor 2N5876 2 3 Transistor 2N5878 2 4 Washers Greaseless 4 5 2179 Heatsink Harness. Long 1 6 2178 Heatsink Harness, Short 1 7 2134 Label‘‘Warning’’ 1 8 6-32 X ¥2""M.S.. P.H.D. 3062 8

DISPLAY SUB-ASSEMBLY PL205409

1 2084D Chassis 1 2 AE205203 Display BD. Assembly lref 3 3064 #6 X Vp" Sheet Metal Screw 6 4 HV18 Hi Voltage XFMR Tl 1 5 MH919TOL Varo Trippler Al 1 6 dAINO56103UA} 10K Pot Alien Bradley R13 1 7 22030B Heatsink-Thermalloy 6 8 6045-B4 Heatsink-Thermalloy 3 9 CRT Socket 1 10 3083 8-32 X 1% Ms. Phil. HD 2 11 3084 8-32 Nuts 2 12 3085 #8 Lock Washer 2 13 .05mf @1500VDC. Cap. 2 14 Wire 9’’, 18 Gage 2 15 Lug, Gnd. 1 16 #6 X Ye Sheetmetal Sc. 1 17 3/16"’Diam 3” Heatshrink Tubing 2 i8 3/16” Diam 2”’ Heatshrink Tubing 2 19 AD205411 (Audio to Display Harness) lref 20 NE2 Neon Bulb 2

AUDIO BOARD-TAILGUNNER PL205202

REF. DE:

1 Diode-Zener D1 IN5240 1 2 Diode-IN914 D2, 3, 4, 5, 6, 7, D8, 9 D10, 11 IN914 10 3 Cap. 470pf 50V Disc. C34, 35, 36 3 4 Cap. .002uf 50V Disc. C17 1 5 Cap. .005uf 50V Disc. Cll, 41 2 6 Cap. .0luf 50V Disc. C3, 18, 19 C20, 23, 30 6

Page 42

AUDIO BOARD-TAILGUNNER PL205202

| _ PART MFGR ITEM NUMBER DESCRIPTION REF. DES. PART NO, QTY

7 Cap. .05uf 50V Disc. C14, 31 2 8 Cap. .luf 50V Disc. C2, 4,7, 9, 10, C12,13, 21, 22 C27, 32, 33, C42, C49, 50 & C51 16 9 Cap. .22uf .35V Tant. C25 1 10 Cap. .47 35V Tant. C28 & 29 2 11 Cap. .68 35V Tant. C6 1 12 Cap. luf 35V Tant C8 1 13 Cap. 2.2uf 35V Tant C44 1 14 Cap. 3.3uf 35V Tant C45, 46, 47,48 4 15 Cap. 4.7uf 35V Tant. C26 1 16 Cap. 10uf 35V Tant. C15, 16, 43 3 17 Cap. 15uf 35V Tant. C24 1 18 Cap. 33uf 35V Tant. C46, 47, 48, 49 4 19 Cap. 100uf 25V Elect. cl, C5. 2 20 Res. 100 OHMS 1%4W 5% Cj R5 1 21 Res. 150 OHMS 14W 5% C| R29, 71, 73 3 22 Res. 330 OHMS 4W 5% C! R41, 42, 46 3 23 Res. 470 OHMS 14W 5% C| R3, 70 2 24 Res. 1K 14W 5% Carbon R10, 16, 22, 34, R45, 60, 81, 88, R 92, 93 10 25 Res. 2K %4W 5% Carbon | R58 1 26 Res. 2.7K 14W 5% Carbon | R21, 27, 28 R48, 49, 78, 79 7 27 Res. 4.7K YW 5% Carbon | R54, 57, 61,94 4 28 Res. 9.1K %4W 5% Carb. | R12 1 29 Res. 10K 14W 5% Carbon | R6, 8, 15, 17,23, R26, 30, 33, 35, R59, 64, 67, 83, R 87, 91 15 30 Res. 15K %4W 5% Carbon | R66 1 31 Res, 20K 14W 5% Carbon | R14, 18, 32 R36, 62, 65,68 7 32 Res. 22K %4W 5% Carbon | R22 1 33 Res. 30K 4%4W 5% Carbon | R44, 69 2 34 Res. 39K YaW 5% Carbon | R19, 37 2 35 Res. 47K %4W 5% Carbon | R9, 24, 74, 76, R77, 85, 89 7 36 Res. 68K /%4W 5% Carbon | R40 1 37 Res. 82K %4W 5% Carbon | R20, 38 2 38 Res. 91K %4W 5% Carbon | R84 1 39 Res. 100K 14W 5% Carbon | R39, 80 2 40 Res. 150K %4W 5% Carbon | R53 1 41 Res. 180K 14W 5% Carbon | R63 1 42 Res. 220K %4W 5% Carbon | R47 1 43 Res. 330K ¥W 5% Carbon | R11, 25, 52, 82 4

7-10

Page 43

AUDIO BOARD-TAILGUNNER PL205202

PART MFGR. ITEM NUMBER DESCRIPTION REF. DES. PART NO. QTY.

44 Res. 360K %4W 5% Carbon | R51 1 50 Res. 390K 1/4W 5% Carbon | R55 1 51 Res. 470K 1/4W 5% C R2, 4, 2 52 Res. 560K 4/4W 5% C R43 1 53 Res. 820K 14W 5% C R50 1 54 Res. 910k 4w 5% C R56 1 55 Res. 1M 4W 5% C R1,7,13,31 4 56 Res. 100K Pot R75, 86, 90 3 57 Trans. 2N3904 NPN Q1,2,9, 10 4 58 Trans. 2N3906 PNP Q3,4,5,8 4 59 Trans. 2N6292 NPN Q6 1 60 Trans. 2N6107 PNP Q7 1 61 1.C. TLO81 IC 1,2,3,7,9,11, 19,24,25,26,27 ll 62 74LS125 1.C. L$125 1Cc4 1 63 1.C. 7404 IC5 1 64 1.C. 7406 1C6,28 2 65 1.C. LS393 1C8,18 3 66 LC. CA3080 1C10,13,22 1 67 74LS123 1.C. LS123 1C12 3 68 LM555 1.C. 555 IC 14.15,16,17 1 69 IC. 7915 1c20 1 70 IC. 7815 Ic21 1 71 IC. L259 1C23 1 72 6071B Heatsink-Thermalloy 2 73 6072B Heatsink-Thermalloy 2 74 09-18-5094 Conn. Molex 9 Pin Jl, J3 2 75 09-18-5069 Conn. Molex 6 Pin J2 1 76 609-1622M Conn. Ansley 16 Pin J4 1 7 4-40 X 1/2 Ms. Rhl. Hd. 4

  • #4 Lock Wshr. Internal 4 79 4-40 Hex Nut 4 80 AW205202 Circuit Board 1 81 CA-165-105D | 16 Pin Socket-Solder Tail 1 82 09-18-5062 Conn. Molex 6 Pin J5 1

2708 PROM BOARD ASSEMBLY (KLUDGE TO CPU) 38-10522-01

1 Heatsink 11SU5, HSU6 6072B 2 2 Heatsink 11SU5, HSU6 6071B 2 3 4-40 Hex Nut 6 4 4-40 Mach. Screw 3/8” 6 Phil. Panhead 5 Test Points 2

Page 44

2708 PROM BOARD ASSEMBLY (KLUDGE TO CPU) 38-10522-01

PART MFGR. ITEM NUMBER DESCRIPTION REF. DES. PART NO. QTY

6 24 Pin Dip Socket U1-U8 8 7 +12V Voltage Reg. U10 7812 1 8 -5V Voltage Reg. Ul1 7905 1 9 2 Line to 4 Line Decod. 7418139 1 10 3.3uf Tant. Cap. 35V 4 a0i 02uf Cap. Disc. 50V 7 12 PC Board 80-10518A 1 13 24 Pin Dip Cable CA-D24P-02- 2 261-CC-10 14 Game Proms 205A-1 Thru 2708 8 205D-2 15 14’’ Swag Spacer #6 1533-C-6-B-1 2 Through Hole for .090 BD. Mfr, Raf. 16 4-40 X ¥/2”’ Phil. Pan 2 Head Screw 17 #4 Hex Nut 2 18 MP203611 Mounting Brkt. 1 19 03-09-1063 6 Pin Molex Male 1 20 02-09-1118 Molex Pins Female 2 21 02-09-2118 Molex Pins Male 1 ref. 22 WL38-10522-01| Wire #1 1 ref. 23 WL38-10522-01 Wire #2 1 ref. 24 WL38-10522-01| Wire #3 1 25 T-18R Ty Wrap 1

JOYSTICK ASSEMBLY PL205413

1 900-098 Joystick 1 2 09-50-3031 Molex 3 Pin Female 1 3 08-50-0126 Female Molex Crimp Terminal 2 4 03-09-1063 Molex 6 Pin Male 1 5 02-09-1118 Molex Pins Female 5 6 ref. WL205413-1] Wire #1 2 7 ref. WL205413-2| Wire #2 1 8 ref. WL205413-3] Wire #3 1 9 ref. WL205413-4} Wire #4 1 10 |ref. WL205413-5) Wire #5 1 11 [ref.WL205413-6 | Wire #6 1 12 |ref. WL205413-7) Wire #7 1 13 |ref. WL205413-8] Wire #8 1 14 Ty Wrap T18R 7

7-12

Page 45

AUDIO TO JOYSTICK WIRE HARNESS ASSEMBLY PL205412

PART MFGR. ITEM NUMBER DESCRIPTION PARTNO. | QTY. —=

1 09-18-5094 Molex Conn. Female 9 Pin 1 2 Molex Conn. Female 6 Pin 1 3 02-09-1118 Molex Pins Female 4 4 02-09-2118 Molex Pins Male 6 5 T-18R Ty Wraps 5 6 ref, WL205412-1] Wire #1 1 7 ref. WL205412-2| Wire #2 1 8 ref. WL205412-3} Wire #3 1 9 ref. WL205412-4) Wire #4 1 10 |ref. WL205412-5| Wire #5 1

AUDIO TO DISPLAY HARNESS PL205411

1 03-09-1063 Molex Conn. 6 Pin 1 2 02-09-1118 Molex Pins Female 4 3 ref. WL205411-1! Wire #1 1 4 ref. WL205411-2} Wire #2 1 5 ref. WL205411-3} Wire #3 1 6 ref. WL205411-4] Wire #4 1 7 T-18R Ty Wraps 3

7-13

Page 46

APPENDIX A

Assembly Drawings, Schematics & Wiring Diagrams

Page 47

COVTROL PANEL, —™]

SPEAKER

warena: 7 Zi owG TITLE onnen ue evan 7) FROUT CABINET ASSY. ‘ALL HOLES, E MLUSTRATION.

ove wo] owe [owe KO” rr NOTES: UNLESS OTHERWISE SPECIFIED MA/ZOSSOL R

}COOE IDENT. L CO 4 3 4 2 1

Page 48

CRT TUBE, 19° MONITOR ASSY.

HIGH VOLTAGE CA

IN LOGe PCB

A-- sccrou f\ iN | ENTER POWER SUERLY

v

——l A+- MATERIAL: cae ry a. CINEMATRONICS BY oa a

NOTES: UNLESS OTHERWISE SPECIFIED

4 3 4 2

Page 49

72 / ume | “amar 3009] kee 031410308 JSIMYSHLO SSTINN ‘SALON

ze TOILVELSYIT1 FIVOS OW O01 apaae SEIT Oetv0e 2QLINOW [ice “nm| oe Send nS ed I) Gd AVIASIT

pal nie (3218) pve ‘Laz WaLLIVM 1NOHIM azinsivssio

Page 50

G31S1D3dS ISMMYSHLO SSTIWN :S3LON TKN ef = Poa

Auvaaiudoud

Page 51

NOTES: UNLESS OTHERWISE SPECIFIED

DATE | Aono wasparres H 70,

COGIC PCE

mate ° [-— oreeaTOe CPTION swreH

CINEMATRONICS [ome

‘Cee 2020 fowG Tie SSS C,PU BOARD ILLUSTRATION, jwOdeL NO, ‘Dwa sz [owe NO. MU Z08BO3 | F TENT.

enaet / oF /

Page 52

J! COMMECTOR DATA

[wie COLOR FUNCTION CRM /veEL CHASSIS GUO.

WAT TXFMR LUG tS

BLK TKEMR LUG #8 |

GR/VEL 6.SVAC GUO.

ORG 6.SVAC BRA ‘SPOT KILL (25Uuie)

yeu +25V.

g qd «<q Bu -26V,

Jeo ‘RED +oV

W727) GRY +5V

Jr BLK +5V RETURN)

ie RED 2 OSV RETURL LX SAMP ILILE FUSE. BY SAME WWE FUSE. BA SAMP IIE CIRCUT BREAKER, CB 1. AX SAMP INLINE CIRCUIT BREAKER CBE.

NOTES: UNLESS OTHERWISE SPECIFIED

JE COMMECTOR DATA

[PUI MOIWIRE COLORR| — FULICTION Je-| | BRN TKEMR Lug aI Je-2 | ORG TXFMR LUGg ve-3| 60 |TFMR wese ve-4| Yeu |7KFMe LuGud

XENTEK POWER SUPPLY

BOTH H&E AS VIEWED FROM THE

FROMT OF POWER SUPPLY. MATERIAL: hei) La teen stil ple CINEMATRONICS [iL \emmE

Ce Williams 19-99 RELEASE APPROV] DATE, shane cro 98| FOWER SUPPLY wenotas. [D0 NOT SCALE Dwa] FYOUT /LLUSTRATION a a a 7 MUEOSEO? | FA a ell coo Tear or?

| 1

N

Page 53

uw y2 03-09-2041

PART OF JI

MOLEX

03-09-2122 100, 115, | 230VAC 10% ' 47-63Hz I

I a)

AC JUMPER SCHEOULE

INPUT |_JUMPER INPUT VOLTAGE |TERMINALS |CONNECTION} 1OOVAC YANO 5 1IBVAC TAN 4 SOVAC TANE 4

[2)recommenneo FUSING; 34 SLO BLO FOR

1.54 SLO BLO FOR 230¥ [i] TRANSFORMER SHOWN WIRED FOR II5VAC OPERATION eine wa pee NOTES: 53279] C [ C292!-SO! EA

00 NOT SCALE OwWG. [SCALE: werent: ___Jeweet_7or7 IN 4720] 4720

l Aevisions {eexTovy] OeecRIeTION brrepoare

wot ----- eee LEX 08-09-2122

(+5¥ i 1! + 9) \+5v

\ \ \ +5V RTN $5V RT [7 (ony

! \ \ I I I i 115y,

©)| F.w.RECT —Vp rOlrsé

pa i! S00 SHAT | |

+ (2) £25v ATN eer | oBe let 3A © ates

\ 71 Sino} +)! 6.3vac LS 0,454 Ea DESCRIPTION PART NO. MATERIAL [manuractunen ['TEM

TIT OF MATERIAL ss ‘SPECIFED] SIGNATURES OATES! on HONS ARE IW INCHES 3 oe XENTEK INCORPORATED eeente n PRE SSUES fre 7a peated reac, Ow aweres [osen,i, Deer abe Te te xn Ty L Bt et) — Ta SCHEMATIC, POWER SUPPLY ct

PROPRIETARY NOTICE

Page 54

ms i et

;

Page 55

ie] 555, Es 3 cis Py “LcpaLcag ~ Aces Z

‘

NOTES: UNLESS OTHERWISE SPECIFIED

Res Raa IOK gik

[SUMMING NETWORK

ics a ‘TLOBI = 845 R74 RB a aK 100K hs

POWER AMP

LAST REF_DES USED] aia ae = = EAT cnctarcowcs EE co car aeetare]owe TUE SCHEMATIC [ele] cores Ibo nor scat JAUDIO BOARD -TAILGUNNEF 1C3S

Page 56

CONN J2

accum. seLect @) a 7406

CONN J4 CONN J3

@ TOT 20 Miz UYeur ) Avoto

osc ELECT ) COIN CONTROL

i BRIGHTNESS

ow

COIN

COUNTER GAME OPTION SWITCHES

Pp M ‘ul T s R N L K J 2 2 2 2 2 2 2 ' Hu G F E [ol [re =} RESISTOR

I 2 2 2 2 be 2 por 2

q

SECONDARY Ce acted | DISPLAY +0 DAC 80's

ED" INPUT SELECT @

FROM CONTROL PANEL

<

<

<

<

< c <

T T PRIMARY ACCUM. (2) = ur 7 R7 7 NG Me. 6 6 ©

EVEN EVEN opp opp LINE LENGTH Cou!

ROM ALU (4) MEM ’

a)

=

z

a

c

o

e

=) ADDRESS SELECT (4) DATA SELECT G) u T s R Pp N M u W "1 a" WW W W W "1

ADDRESS COUNTER © INSTRUCTION ADDRESS REGISTER @) REGISTER nam storace ©) v] T s R P N M L 144 13 13 13 13 14 14 14 y 14

RAM DATA REGISTER () *OR 16-LEVEL INTENSITY CIRCUITRY

Page 57

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 58

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 59

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 60

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 61

_NETSR »

a4s07

. HTIAL_POSITIRN ‘Tai NORMALIRE VECTOR

Sy Ae xOR?

xons

Drawne

I Hs008r bad L cs

Ling DRAWN Line Done ee La uapiee = arth che ayate Tinee ig

se 1G" p18 [. a | [ be N MM ke is a wey p-nom 5 i (Poe ae 4 | } 2 ey * a . 7

>t ee we ls le de de > fF Lume 20He Lec > G > pee CO ees © he CABLE TIMER ay en] alt em tt env & De Ce ETA) oy TAKSIGS rN TALSICS Hbecn TALS Ga Fousicri tone TIMER 9d ane, 24 Loan 24 Lene aot wm wf ah ee | te chk ae “4 ry ry a ry ry ry " " ry ry [e ioe

o 3°

Phe [Phe [PAs 1PRs ]5Au | EAw [Sty 546 Thy [Phe [PAS [PAZ [SR 1SAG |SAE | SMe Pay | PAL | PAL | Pho |5Ay 15a [SA | She he

VECTOR nm hw hw me 1 z

Tem 5.2 aise aust MR =a in u oars Pre ee ee Ce ee ee ee eT Paro ao as_or asl pe dele ye pele de 2 eye pe pete tele ee fate le lee fo ( LS, Ti dim bx dae bv GK dus oH ne bse xe bm oR bux dy bn be bu bude dn ly & Soo wo Same ow Fe FG espe 3G 7 8

Page 62

SEE PL 205404

§ e cree . Rua Bak vew 2u2I0; Ra) \ 82k 1/2W [er CRIS, an 200 9A os aa ( 7 Ne i383 <a}

82k Yaw ° (ci? hs RIL 10K Ma i Te Ria os

or}

2 ALL DIODES ARE IN4OO3 UNLESS

CTHERWSE SFECIFIED. 2 ALL HESSTOR VALUES ARE IN ‘OHMS, I/4W UNLESS OTHERWISE SPECIFIED.

TALC

NOTES:

LCITOR VALUES ARE IN MICROFARADS, @o22 BROW 2’ +22 BROWN 3.1/4" +8 Buck 43/4" [Dew reps Ben Bue s CUT ® 1014" War

BLACK] TWIST TOGETHER ¢

we Bo

i u av i H H Owitay ELecTECHCS PC. ASSEMELY. AE 2 al os eerie

Page 63

TOTTOTS arr] Gu ama] 436.4 Diawwanes =. $7INOdLIINN AWIdSIO 'FT4IL +

‘ON S9INOM yW3Nlo Sree Wet

1D ms 8012 ‘smaayiors 7 v0 :NOILLAWD C pooa Fr

Page 64

REVISIUND [DATE J 4-79 | ceo

trv) ta] Angin VOLTACE ‘Awook Jo To peTURS TOE we

SI 2.72 |W RESISTORS

st +8 7805 oe “ele Tv BLU (4) os GRID 4 TF mee

ALG CAPACITOR VALUES ARE 18 MICROFARADS

ALL AWSISTOR VALYES ARE IN OWMS UNLESS OT MES WISE NOTED

NOTE: © Rite THRU RIZ AMO AZZe THRU AEZ9 ARE COMPOSED OF THESE PowsR TRAWSISTORS ARE movWTED ow HEAT SINKS AND ARE SEPRATE FROM -THS PL, BOARD (OWE. NG EI) @ THESE ARE SOLDER CONNECTIOW PoTs ON THE PLC. BOARD

+S volts

CKT BASE CONNECTIONS

PIN FUNCTION

FILAMENT

GRID | GRID 2

GRID 4

OPEN

GRID | CATHODE.

—amtOona CINEMAT ics, IC. TITLE: DISALAY KLECTADMICS SCHEMATIC

Page 65

J3 aan t 2! HORIZ. POT 2 | 3. HORIZ, POTS | VERT. POT | VERT. POT 2 | HORIZ. POT | 6 -+—

VERT FOT3!

J25 GND

4 ALL DIODES Ait 1's9I4 UNLESS OTHERWISE SPECIFIED.

3 C49 C5C, AND CSI ARE BYPASS CAPS. (luf, SOV)

FROM GRCUND TC +5v.

2 ALL RESISTOR VALUES ARE IN OHMS

I74W £% UNLESS CTHERWISE SPECIFIED.

Lt CAPACITOR VALUES ARE IN MICKOFARADS,

SOV, UISE. UNLESS OTHERWISE SFECIFIED. (NOTES: UNLESS OTHERWISE SPECIFIED

JOYSTICK CIRCUITRY

joa Tid SCHEMATIC. DIO BOARD TAILGUNNE! 205202 [x 8 7 6

I 1

Page 66

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 67

PROPRIETARY

‘THIS DOCUMENT 18 THE PROPERTY

OF CINEMATRONICS INC. AND 15

MOT TO BE REPRODUCED OR

DISTRIBUTED WITHOUT WRITTEN [AUTHORIZATION OF CINEMATRONICS

REVISIONS,

DESCRIPTION tne. ew a a we 4

H ve MASTER PLAYER CONTROL PCE

1 \ fl ' 1 | TOCOM | 2 H | QOOR i 1 3 ! 1 i) 1 I 1 a4 1 I \ ! as ' ! i) 1 26 ' OIE-2 79 ey rmee—L sw i ' - “4 ° ! Tose-1 ! 6 owen. swe !

° \ TOUE-3 1 sraer —1_ sw \ ' 2 oo i Hy arn TRACT SHO, 2--. JUMPER 1 ! POMAL ATTRACT wi ! \ I \ ‘ 1 3 | 1 | AUX PLA) é + couren B64 =|

t ! | ' H !

! H ad ; Speseein 1 1 FAGIA OL MYSO ; LAYSIICK) 2 13804 | ICOMNECIC A I 1 \ 1 + ' 1 I f= === == = = ad MATERIAL: ‘DRAWN BY" oar e] Cajon

hassles CINEMATRONICS JCMS Ta — a] OWG TITLE SREAR ALL SHARP: = <1 SCHEMATIC DIAGRAM - ALL HOLES, joo NOT SCALE DWG LAYER CONTROL, TAILGUMMER TOLERANCE: UNLESS JSPhEROSE SetciritD |WODeL WO] ow [OW No. ma NOTES: UNLESS OTHERWISE SPECIFIED FRSTEGTION [CATE ie | 80205205 _|A

|= OME. TENT, I ‘eHanT / OF 7 4 3 2 1

Page 68

PROPRIETARY

THIS DOCUMENT IS THE PROPERTY

OF CINEMATRONICS INC. AND 18

MOT TO BE REPRODUCED on

DISTRIBUTED WITHOUT WRITTEN

AUTHORIZATION OF CINEMATRONICS.

nc. +15 3 PIN FEMALE HOOKUP. Cs DESCRIPTION DATE | APPROVE!

TO MASTER CONTROL

  • NC BOARD v3

HORIZ. POT

NOTES: UNLESS OTHERWISE SPECIFIED TO AUDIO TO JOYSTICK HARNESS aa ST Ercan esi tal Gall civemarnonics [eet Soo

Pengiecr an [ate 10-7}

ry DAEAK ALC SHARP HOOKS AND OSBURR ALL MOLES. aiaase sernortoare] WO ME JOYSTICK ASSY

coy iad DO NOT SCALE SCHEMATIC DIAGRAM

TRANCE UNLESS OrMERWnse: SPeCiniED iT nO] owo cd

ze jowa NO. <_|SD205413_ [A PES -O-[NONE [eoor oem Leet or

a r | 1

Page 69

Mol “FN, 09-09-1063 (/EA,) MOLEX: PIM - BM. 08 -09-2//8 (/EA.). MOLEX FEMALE SOCKET: PAY. 08-09-1168 (IEA). FR

THERMALLOY TRANS. SOCKET JS REF 80203201 500 783, PU. B18-PF-608 (4EA,),

WHITE | | s 2nse78 q

cer ] | 2 BACK 2N5876 ) L AR Scere HEAT SIUK HARNESS, 2:78 \\ Ler aux 20rd

+ | Y 9.20 £88 rE RED. 6 | s WHITE 25878

ORAMGE | | oaty | | 2 | 2 BACK 2U5876

GREEN | | /

) l : v a HEAT SUIK HARNESS, 2179 ‘HEAT SUK, E7A MOLEX COUM.-PL/.08-09- 1068 (/EA). MOLEX MALE PIAI- PAL. 02-09 -2//8 (1A). MOLEX FEMALE SOCKET- PA). 08-09-18 (56).

‘MATERIAL: Eicon

SaE clNEMaTRonics Vea aceite en FnISH: TaLease appnovjoate| ONG TITLE §= SCHEMATIC, meaw aut suane | ctes 18-74] VERTIOALL HORIZONTAL, Reto: [DO NOT SCALE OWG] HEAT SINK ASSY. GPRERWnSE arecinigo [MODE WO] bua Towa WO. cy NOTES: UNLESS OTHERWISE SPECIFIED SROTCTION SCALE? C 150205405 |A

Ee @-|KOUE |eson vem [ent of 4 3 4 2 ] 1