Heavy Barrel 2 Player Conversion Kit
Heavy Barrel (World) (Data East Corporation, 1987) · Kit Manual · 12 pages · 4 sections · original scan
MANUAL PART NUMBER: 780-0086-00
DATA EAST USA, INC.
470 NEEDLES OIE
FCC WARNING uses radio frequency energy and if not installed and used property, ie; in strict accordance may cause harmful nterterence to radio communications. Ths equpment has been tested ‘comoky with the imits for a Class @ computing device pursuant to Subpart J of Part of the FCC rules, which to prowde reasonable protection aganst such interference when the equgment is operated in a . this equoment in a residential environment is Ikely to cause interference in which case the user, at hes awn required to take whatever measures are necessary to correct the interference.
FB! WARNING
Federallaw provides severe cad and crammal penalties for the unauthorized reproduction, t&stribution, or exhitition of copyrighted audio-visual works and \deo games. The Federal Bureau of Investigation mvestigates afegations of criminal
COPYRIGHT NOTICE
Heavy Barrel" is Copyright 1968 Data East Corporation, sold exclusively in the United States of America and Canada by Data East USA, Inc. Al richts reserved.
ENVIRONMENTAL DATA
This product is intended for use indoor use onky, power requirements are 105-125 volts AC, SO-60 hy, and requires a3 ware grounded outlet.
SERVICE PROCEDURES
To obtain replacement parts and technical service, contact the authorized Data East Distributor in your area, if you require referral or further technical assistance, you may contact Data East’s Customer Service department during the hours of &00 am to 5:00 om Pacific Tane at (408) 286-7074.
AAMA WARNING DATA EAST USA, INC. in cooperation with the American Amusement Machine Association, has nstaled an “AMA PROTECT" certification abel on each HEAVY BARREL PCB manufactured for legal sale in the United States you are offered a BARREL PCB that does not have the "RAMA PROTECT” certification label, wou shoul suspect that the board ts not legal, and shouk! contact DATA EAST USA, INC, at (408) 286-7074, or Bob Fay of the AAMA at (703) 548-2044,
HEAVY BARREL
CONVERSION KIT
MODEL NUMBER: 1US33K
INSTALLATION & SERVICE MANUAL
TABLE OF CONTENTS
GENERAL INFORMATION
+ Specific Requirements.....seseseecseceseees
List of Materials..cscssccccsccsencssevenee
Installation Instructions...cccccsccsescscecaseseeresned
GAME INFORMATION
« Game Options.. eee ere ceereenereccererees 6
PCB Edge Connector Pin-Out.....cecscssceesrevevcsvevcsseel
. Rotary Control Connector Pin-Out....cseecseereseeseree eB
© 1968 DATA EAST USA, INC. 470 NEEDLES DRIVE SAN JOSE, CA. 95112 (408) 286-7074
FIRST PRINTING FEBRUARY 1988
PN: 780-0086-00
GENERAL INFORMATION |
[a Specific Requirements.
The Heavy Barrel game is a one or two player video game conversion kit. It is intended to be installed into an existing video game cabinet and comes with all the necessary components to make the converted game look and play like a new dedicated game!
THE GAME TO BE CONVERTED MUST MEET THE FOLLOWING REQUIREMENTS
MONITOR Vertical, RGB, negative Composite Sync input.
POWER SUPPLY + Svde @ 7 amp, +12 vde @ 1 amp, -Svdc @ .Samp (MIN)
List of Materials.
DESCRIPTION PART NUMBER
| 1 | PCB, HEAVY BARREL | 510-0126-00 |
| 1 | MAIN HARNESS, JAMMA, KIT | 036-0158-00 |
| 2 | JOYSTICK, 8 WAY, ROTARY | 450-0012-00 |
| 2 | PUSHBUTTON ASSY, YELLOW | 350-0016-04 |
| 4 | PUSHBUTTON ASSY, RED | 350-0016-02 |
| 4 | PUSHBUTTON, SHORT, GREY | 350-0001-08 |
| 4 | PUSHBUTTON HOLDER W/SWITCH | 185-0001-00 |
| 4 | PAL NUT, NYLON | 240-0001-00 |
| 1 | CNTRL PNL OVERLAY, HEAVY BARREL | 800-0031-00 |
| 1 | UNDERLAY CARD, HEAVY BARREL | 810-0029-00 |
| 2 | SIDE DECAL, GENERIC | 820-0040-00 |
| 1 | MARQUEE PLEX, HEAVY BARREL | 830-0037-00 |
| 1 | LABEL SET, PUSHBUTTON ID | 406-0085-00 |
| 1 | FCC WARNING LABEL | 406-0003-00 |
| | | MANUAL, INSTALLATION & SERVICE | 780-0086-00 |
PAGE 1 INSTALLATION & SERVICE MANUAL
| Installation Instruction |
When selecting a game to convert, make sure that the Power Supply, the Monitor, and the Coin Acceptors are functional. There is nothing more frustrating than installing a conversion kit and having it not operate due to a faulty Monitor or Power Supply. I know...we will all suspect that the new Logic PCB is defective, right?
It is mandatory that the cabinet be wired to conform with all National and Local Electric Code requirements before the conversion is attempted, The primary section must have adequate noise filtering on the AC line to prevent unwanted conducted radio frequency interference. ‘Adequate’ is defined as a filter with both common mode and differential mode filtering and a minimum current capacity of 1 % amperes,
According to the FCC and other regulatory agencies, every video game must have be clearly labeled with the Name and Address of the Original Manufacturer, Date of Manufacture (or serial number), Voltage Rating, Current Rating, Suitability for indoor or outdoor use, and Model Number. In addition, the FCC requires that after conversion, the unit must be labeled with a suitable warning stating that radio frequency interference may result from use in a residential area. An acceptable sticker is included in this kit.
IT IS THE RESPONSIBILITY OF THE PERSON PERFORMING THE INSTALLATION TO COMPLY WITH ALL LABELING REQUIREMENTS.
TAKING IT APART...
Performing a few simple tasks when preparing a game to be converted can save you much time and effort when you are installing the conversion kit.
Find the wiring diagram of the game to be converted! You will need to identify the required DC power supply output wires and the monitor video and sync wires. Note the color coding of these wires or better yet, label them as to their function. This kit contains a new Main Harness, but you will need to splice it into the existing power supply and video wires.
Remove the existing game harness parts that will not be used in this conversion. NOTE: You are modifying only the secondary (DC from power supply) and I/O (video, speaker, and controls) section of the wiring. DO NOT MODIFY OR REMOVE THE PRIMARY AC WIRING. The primary AC wiring has been designed and built to comply with UL and FCC regulations and must not be altered.
INSTALLATION & SERVICE MANUAL PAGE 2
Installation Instructions (cont.) | !
Remove the game PCBs. Remove all exterior decals and repaint the cabinet if necessary. Repair any cabinet damage at this point. Remove the monitor plex (or glass). If your plex has silkscreened artwork on it, you will need to strip it off, or replace the plex with a piece cut to the same size. Using the Monitor Plex as a template, cut the supplied Underlay Card to the same size as the plex. NOTE: Be certain that the opening in the Underlay Card lines up with the Monitor CRT,
Remove the Marquee Plex from the game and use it as a template to cut the new Marquee Plex down to the correct size. Remove the control panel from the game and remove all controls and graphics from it. NOTE: Save a Player Start button, as one is not supplied in this kit.
PUTTING IT TOGETHER...
Control Panel: This is never any fun, so lets do it first and get it out of the way. Select a button and joystick layout that fits your control panel size. Refer to figure 1 for the suggested panel layout.
START START
ROTARY ‘1% © O ROTARY
6C ICK JOYSTICK
Grey ED OOOO OOUOO
oO SHOOT SHOOT GRENADE GRENADE SHOOT SHOOT GRENADi
Figure 1
PAGE 3 INSTALLATION & SERVICE MANUAL
Installation Instructions (cont.)
Install the Control Panel Overlay by peeling off the paper backing and carefully laying the overlay down onto the panel. Smooth it out starting in the center and working your way out to the edges, removing all of the trapped air pockets. If possible, cut the edges of the overlay oversize and fold the excess under the panel. Cut out the button and joystick holes. Install the Control Function Labels found on the sheet of labels supplied in your kit. NOTE: Install the Control Function Labels in the formation shown in figure 1.
Cover the Control! Panel Overlay and Control Function Labels with a clear plex ta protect the overlay and labels. Install the buttons and joystick at this time. NOTE: This conversion kit does not supply the Player Start button, You must use a button removed from the control] panel in an earlier step. Mount the completed control panel to the cabinet.
Game PCB: Mount the game PCB set to a convenient wall of the cabinet using the mounting feet and hardware supplied with the pcb.
Power Supply Wiring: Plug the Main Harness edge connector onto the Game PCB's edge connector. Separate the DC Power wires and route them through the cabinet to the Power Supply. Try to keep the length of these wires to a minimum for best results. NOTE: Use a minimum of 2 wires EACH for the +5 Volts and the Ground lines between the power supply and the PCB. Terminate them at the Power Supply as required.
THE DATA EAST MAIN HARNESS HAS LABELS ON THE EDGE CONNECTOR TO ASSIST IN IDENTIFYING EACH TERMINAL’S PIN NUMBER AND FUNCTION.
Player Control Wiring: Route the Pushbutton and Joystick wires up to their proper destinations, cut to length, and terminate as required.
REFER TO THE EDGE CONNECTOR PIN-OUT ON PAGE 7 FOR WIRE COLOR AND FUNCTION INFORMATION.
INSTALLATION & SERVICE MANUAL PAGE 4
Installation Instructions (cont) |
Monitor Wiring: The game PCB set has outputs for Positive Red, Green, Blue, and Negative Composite Sync. lf your monitor has separate Horizontal and Vertical syne inputs, hook the Composite sync to the negative Horizontal input. This method will work on most monitors, however some model Electrohome’s require that the Composite sync signal be hooked up ta both the negative Horizontal and Vertical inputs. Contact your distributor for more information if you are uncertain as to how to hook up the monitor wires.
Coin Door: The Coin Counter(s) may be the 12 volt or 6 volt type as the game PCB utilizes an open collector drive circuit. Hook one coin counter wire to the required voltage (+12v or +5v) and the other wire to the coin counter signal wire from the game PCB.
Graphics: Install the Game Instruction Labels onto the Underlay Card, either in the lower portion, or on one side of the picture tube cutout. Install! the Underlay Card under a clear monitor plex (or glass). Mount the new Marquee Plex, and install the Side Decals. NOTE: Install the FCC Warning label to the upper rear of the cabinet.
THE BiG TEST!
REMOVE THE MAIN HARNESS EDGE CONNECTOR FROM THE GAME PCB!
Apply power to the game. Measure the +5 volts at the edge connector and adjust to +5,15 VDC using a Digital Multi-Meter. Measure the +12 and -5S vdeo wire to be certain they are connected properly and are on the correct terminals, Remove power to the game.
RE-CONNECT THE MAIN HARNESS EDGE CONNECTOR!
Apply power to the game once again. The attract mode video should appear on the screen. Adjust the picture size and colors on the monitor to get the optimum appearance. Adjust the Sync and Hold controls on the monitor for a stable picture. Coin it up and give it a try! Test all the controls and sound for proper operation.
Congratulations! You have successfully installed your Data East conversion kit! We hope that it gives you many years of successful operation.
PAGE 5 INSTALLATION & SERVICE MANUAL
| 2. GAME INFORMATION
A. Game Options.
The game options can be changed via 2 banks of dip-switches on the game PCB set. Be certain to remove power to the game when changing settings.
DIP SWITCH 1
CREDIT: CREDIT: CREDIT: CREDIT:
DIAGNOSTICS MODE
DEMO MODE SOUND
SCREEN REVERSE
DON’T CHANGE
ACTION
NUMBER OF THREE (3): LIVES FIVE (5): ONE (1): INFINITE (@): GAME DIFFICULTY
BONUS LIVES 30K280K*160K: AWARDED AT: SOK*120K2190K: 100K®200K*300K: 150K*300K*450K: CONTINUE MODE NO: (BUY-IN) YES: DON’T CHANGE *
INSTALLATION & SERVICE MANUAL PAGE 6
PCB Edge Connector Pin-Ou
The game PCB set uses a 56 pin ‘JAMMA’ standard Edge Connector pin out as shown below in figure 2.
GROUND
GROUND
«8 VOLTS
+8 VOLTS
-5 VOLTS
BLOCKING KEY +12 VOLTS
VIDEO-GREEN
VIDEO-SYNC
SERVICE su.
TILT Sw. (N/A) s © BK/GH
COIN SWITCH 2 cn
2P START START
2P UP : up
2P DOWN
2P LEFT
2P GRENADE
NOT USED
Figure 2
PAGE 7 INSTALLATION & SERVICE MANUAL
Rotary Controller Connector lu
The Rotary Controller section of the joystick assemblies must be plugged into the Game PCB. Each controller has a 13 pin cable which plugs into CN 5 and CN 6 as shown in figure 3 below.
+ S$ VOLTS _ + § VOLTS GROUND GROUND INPUT XA INPUT XB INPUT YA INPUT YB
2 PLAYER ROTARY CONTROL CABLE 1 PLAYER ROTARY CONTROL CABLE Rees orticaL sensor input HHI wot usep ow Heavy sanaen [| 2? _] =—_ 4
Figure 3
INSTALLATION & SERVICE MANUAL PAGE 8
WARRANTY INFORMATION
warrants only to the original purchaser (“Buyer”), of its ted below are free from defects in material and vice for the period specified: Data East USA, Inc., (“Seller”), products that the items lis workmanship under normal use and ser
GAME LOGIC PRINTED CIRCUIT BOARD(S) 90 DAYS
No other parts of the Seller’s products are warranted,
Warranty periods are effective from date of initial shipment from Seller to Buyer. Seller's sole liability shall be, at its option, to repair or replace products which are returned to Seller during the warranty periods specified, provided:
- Seller is notified promptly upon discovery by buyer that stated products are defective.
- Such products are properly packaged and then returned freight pre-paid, to a place specified by Seller.
This warranty does not apply to products damaged during shipment and/or due to improper handling, or due to improper installation or usage, or alteration, In no event shail Seller be liable for any anticipated profits, ioss of profits, loss of use, accidental or consequential damages, or any other losses incurred by the customer in connection with the purchase of a Data East USA, Inc., product.
WARRANTY DISCLAIMER
EXCEPT AS SPECIFICALLY PROVIDED IN A WRITTEN CONTRACT BETWEEN SELLER AND BUYER, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.