Rescue Raider Universal Field Kit Instructions (M051-00J18-A011)
Rescue Raider (5/11/87) (non-cartridge) (Bally Midway, 1987) · Kit Instructions · 48 pages · 18 sections · original scan
RESCUE RAIDER
Universal Field Kit Instructions
Coll MIDWAY MFG. CO.
10601 W Belmont Avenue Franklin Park. illinois 60131 USA
Phone (312) 451-9200 Cable Address MIDCO Telex No%, 72-1596
MOS 1-00J18-A011
ELECTRICAL BULLETIN: FOR ALL APPARATUS COVERED BY THE CANADIAN STANDARDS ASSOCIATION (CSA) STANDARD C22.2 NO. 1, WHICH EMPLOYS A SUPPLY CORD TERMINATED WITH A POLARIZED 2-PRONG ATTACHMENT PLUG.
ATTENTION: POUR PREVENIR CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR. UNE PRISE DE COURANT OU UNE AUTRE SORTIE OE COURANT, SAUF Si LES LAMES PEUVENT ETRE !NSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT.
Belly MIDWAY
Inuiles You To Use
ouR TOLL FREE NUMBER FOR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER BALLY/MIDWAY™ GAME YOU NOW HAVE ON LOCATION.
CALL US FOR PROMPT, COURTEOUS ANSWERS TO YOUR PROBLEMS
ANSWERS TO YOUR PROBLEMS.
Video or Pinball - Continental U.S. 800-323-7182
Bally [MIDWAY 10601 West Belmont Avenue Franklin Park, Illinois, 60131 phone (312) 451-9200
©COPYRIGHT MCMLXXXVII_ BY BALLY MIDWAY MFG. CO. ALL RIGHTS RESERVED.
NO PART OF THIS PUBLICATION MAY 8E REPRODUCED BY ANY MECHANICAL, PHOTOGRAPHIC, OR ELECTRONIC PROCESS, OA IN THE FORM OF A PHONOGRAPHIC RECORDING, NOR MAY IT BE TRANSMITTED, OR OTHERWISE COPIED FOR PUBLIC OR PRIVATE USE, WITHOUT PERMISSION FROM THE PUBLISHER. THIS MANUAL IS FOR SERVICE USE ONLY, AND NOT FOR GENERAL DISTAIBUTION. FOR PERMISSION REQUESTS, WRITE: BALLY MIDWAY MFG. CO., 10601 W. BELMONT AVE., FRANKLIN PARK, IL 60131.
Printed in U.S.A.
RESCUE RAIDER - UNIVERSAL FIELD KIT TABLE OF CONTENTS
- SYSTEM “INFORMATION : Lo oe Co PAGE - GAME DESCRIPTION .i+--++ ap rie desta jaseeeee . SELF TEST. ...cesseeeee ‘ OPTION SWITCH SETTINGS . KIT CONVERSION PROCEDURE -.
ILLUSTRATED PARTS BREAKDOWN FIGURE 1 - SUGGESTED MTG. OF NEW CONTROLS ON EXISTING CONTROL PANEL ........ 10 FIGURE 2 - NEW CONTROL CABLE ASSY. CONNECTED TO NEW CONTROLS ...... . FIGURE 3 - PLACEMENT OF NEW ELEC. ASSEMBLIES IN GAME CABINET .. DECAL INSTALLATION INSTRUCTIONS ....eceeesesccscececcs RESCUE RAIDER UNIVERSAL FIELD KIT - PARTS LIST ......... POWER CHASSIS ASSY.: ILLUSTRATION ..... POWER CHASSIS ASSY.: PARTS LISTS .... JOYSTICK ASSY.: ILLUSTRATED PARTS ...
WIRING DIAGRAM, COMPONENTS LAYOUTS & SCHEMATICS
UN-PROGRAMMED SMUDGE CPU BD. - COMPONENT LAYOUT ......
AUDIO 6VB BD. - COMPONENT LAYOUT ........ AUDIO 6VB BD.-- PARTS LIST ..... AUDIO 6VB BD. - SCHEMATIC ....... : LINEAR POWER SUPPLY BD. - COMPONENT LA LINEAR POWER SUPPLY BD. - PARTS LIST ......
-i-
The following safety hints apply to al] game operators and service personnel. Specific warnings and cautions will be found “throughout this manuat where: they apply. .
WARNINGS
AC POWER CONNECTION. Before connecting the game to the AC power source, verify that the proper voltage-selection plug is installed on the electronic chassis assembly.
PROPERLY GROUND THE GAME. Customers may receive an electrical shock if this game is not properly grounded! To avoid shocks, do not plug in the game until it has been inspected and properly grounded. Sente game should only be plugged into a grounded 3-wire outlet. Customers may receive an electrical shock if the control panel is not properly grounded! After servicing any parts on the panel, check that the grounding wires are secure. Only then should you lock up the game.
DISCONNECT POWER DURING REPAIRS. To avoid electrical shock, disconenct the game from the AC power source before removing or repairing any part of the game. When removing or repairing the monitor, extra precautions must be taken to avoid electrical shock because high voltages may exist within the display circuitry and cathode ray tube (CRT) even after power has been disconnected. Do not touch internal parts of the display with your hands or metal objects! Always discharge the second anode from the CRT before servicing this area of the game. To discharge the CRT: attach one end of a large, well-insulated, 20-kV jumper tc ground. Momentarily touch the free end of the grounded jumper to- the anode by sliding it under the anode cap. Wait two minutes and discharge the anode again.
USE THE PROPER FUSES. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.
HANDLE FLUORESCENT TUBE AND CRT WITH CARE. If you drop a fluorescent tube or CRT and it breaks, it may implode! Shattered glass can fly eight feet or more from the implosion.
PROPERLY ATTACH ALL CONNECTORS. Make sure that the connectors on each printedcircuit board (PCB) are properly plugged in. If they do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty.
-ii-
WARNING
The parts. ‘contained in this field conversion kit must be installed without deviation’ from. the instructions contained in this manual, and kit. Failure to follow these instructions in every detail may result in the creation of illegal interference to radio and TV reception.
BALLY MIDWAY has verified that this field conversion kit, when installed in the game(s) specified in this manual, complies with the requirements in Part 15 of the FCC rules for a Class A computing device. Operation of this equipment in a residential area may cause unacceptable interference to radio and TV reception, requiring the operator to take whatever steps are necessary to correct the interference.
BALLY MIDWAY will not be responsible for incomplete or improper conversions, or installation in a game for which this field conversion kit is not intended. If this field conversion kit is installed in a game that is not specified in this manual or in a previously converted game, the operator is required to take whatever steps are necessary to insure compliance with the requirements in Part 15, Subpart J, of the FCC Rules for a Class A computing device.
SPECIAL NOTES:
THE PARTS REMOVED, WHILE MAKING MODIFICATIONS LA’ > WILL NOT
The word “discard“, as used in this manual, makes reference to this fact. All parts removed may be considered usable for other purposes.
Please be advised that when converting a game, it is advisable that all former trademark and copyright registrations be removed in the conversion process.
-iii-
RESCUE RAIDER GAME REVIEW
The following is a description of how Bally Midway's video game “Rescue Raider" operates. It is composed of two parts: a Game Play description and a Self-Test Mode description.
GAME PLAY
RESCUE RAIDER'S setting is a tropical island of forests, swamps and plains. It is “enemy-occupied" and several hostages are held in a variety of stockades and fortresses. The object of the game is to locate and rescue them as quickly and as "unscathed" as possible (using secret weapons and escape clues), to destroy all the enemies, and then get off the island. One or two players can play, and in the two player mode, the players alternate each time one of them is killed by the enemy. Whenever a player loses his last life, he.is always given the option of adding a coin and continuing game play where he left off. The number of coins the player used to reach the end of the game is displayed in the high score table.
During game play, two joysticks are used: one (located on the left side of the control panel) to mave a high-tech, anti-tank vehicle that represents the player; and the other (located on the right side of the control panel) to shoot various weapons. There are four levels of playing difficulty. In each level, a special weapon is provided for use against enemy tanks, land mines and armored cars. In addition; to correct aiming, the player must adapt to each weapon against increasingly complicated barriers and an ever-more-aggressive enemy. Sometimes highly sophisticated, the weaponry includes a grenade launcher and cruise missiles. Also, the player's vehicle can become airborne by using a jet- Pack. These “special weapons" are used by the player by first finding and picking up the weapons. Then the main machine gun or the currently attached “special weapon" is selected by pressing the “special weapon" button. The screen is vertically divided into two parts, the largest depicting the play field. About one-quarter of the screen's right side resembles a computerized control panei with four different displays. One details the sector of the island presently occupied, with a flashing box to highlight player location and radar blips that pinpoint the positions of secret documents and hostages. The other three displays show the direction to: clues, fuel dumps, ammunition, etc.; the type of weapon currently in use; and a record of hostages rescued and those not yet freed. Scoring (based on enemies destroyed, hostages rescued, and secrets found) is shown at the top of the screen where a gauge also indicates fuel supply. Opportunities to refuel occur throughout the game. The player is awarded one bonus life for each hostage rescued.
The level of game difficulty increases with a northward movement on the island through 4 zones. The player continues to struggle to ward off the enemy, locate clues, fuel, and weapons, circumvent walls and water and rescue hostages, until finally reaching an escape ship in a strongly protected harbor. In order to progress to the next zone, the player must find, destroy and drive thru a "gate" which separates each zone. Upon reaching the escape ship, the player is awarded bonus points for the number of hostages and secret documents retrieved, and for the number of lives and amount of fuel remaining at the end of the game.
SELF-TEST MODE
A special "test mode" is built into the game that allows the operator to check the current game option settings, to view the player statistics that are gathered, and to reset the statistics and the high score table.
The self-test mode is entered by flipping the existing “test switch" (which should be located on or near the coin door) at anytime. The first screen is an input, output and options setting display. While this display is on the screen, ensure that the joystick switches and the "SPECIAL WEAPONS" button are operating correctly. Especially make sure that the 45° positions of both joysticks (where 2 switches are closed at the same’-time) are easily reached (bend the contact tabs on the joystick to adjust when the switch opens and closes).
While in this mode, the lighted "SPECIAL WEAPONS" control panel button will
blink. Make sure the bulb is working.
The current game switch options are also displayed on this screen. Flip the dip switches at SWl and SW2 to change the option (see "Option Switch Settings” on pages 6 and 7). :
Press the START 1 button to go to the next screen. The next screen contains Game Time Statistics, which includes: total plays; total coins; average time per game; average time per coin; maximum game time; and a histogram of game times. (Note: the histogram shows GAME TIME statistics, mot TIME PER COIN statistics). The important piece of information here is the average time per coin. If the average time per coin is too long, then make the game harder by reducing the number of lives given per coin or by reducing the minimum game time. If it's too short, increase the number of lives per coin or the minimum game time by resetting the proper option switches.
Press START 1 to go to the next screen: Game Score Statistics. Here is presented the total number of games, the all-time high score, and a histogram of game scores (X 10,000).
To reset the statistics, press START 2, twice. This resets the statistics and the high score table.
Flip the test switch button at any time to go back to game play mode.
“RESCUE “RAIDER 'U.R. OPTION SWITCH SETTINGS
SWITCH NO. 1 (SWL) = AT EL - LOCATED ON SMUDGE CPU BOARD
|| TTT TTT TTT ILTTITIT TITY RRXOUS. GAMEPLAY OPTIONS /7////L/IIHIITIITVIFLTITT| ~ DURING GAME PLAY: - ‘SWHL SWH2 SMES SWFA SWHS SWIG SHAT SAO | NO USED USED
- 4 LIVES ON EACH COIN 5 LIVES ON EACH COIN 6 LIVES ON EACH COIN 3 LIVES ON EACH COIN
- MINIMUM GAME TIME: 90 SECONDS MINIMUM GAME TIME: 60 SECONDS MINIMUM GAME TIME: 45 SECONDS ON OFF MINIMUM GAME TIME:120 SECONDS OFF = OFF
- KEEP HIGH SCORES ON POWER UP ON RESET HIGH SCORES ON POWER UP OFF
- MUSIC IN ATTRACT ON NO MUSIC IN ATTRACT OFF
- INDICATED FACTORY RECOMMENDED SETTINGS PART NO. MO51-00J18-A007 OFF ON
~ RESCUE RAIDER UR. :
certo. SWITCH SETTINGS
SWITCH NO. 2 (SW2) - AT E2-- LOCATED ON SMUDGE CPU BOARD MATA COINS PER CREDIT: [TTT SST THTTTTTCTT VARIOUS CREDIT. OPTIONS :
FREE PLAY
- 1COIN / 1 CREDIT 1 COIN / 2 CREDITS 2 COINS / 1 CREDIT 3 COINS / 1 CREDIT
- NO BONUS COINS COINS ADDS 1 BONUS COIN COINS ADDS 1 BONUS COIN COINS ADDS 1 BONUS COIN COINS ADDS 2 BONUS COINS COINS ADDS 1 BONUS COIN COINS ADDS 2 BONUS COINS COINS ADDS 3 BONUS COINS AAAS Pwr
- LEFT COIN MECH X 1 LEFT COIN MECH X 2
RIGHT COIN MECH X 1 RIGHT COIN MECH X 4 RIGHT COIN MECH.X 5 RIGHT COIN MECH X 6
- INDICATED FACTORY RECOMMENDED SETTINGS PART NO. M051-00J18-A007
RESCUE RAIDER UNIVERSAL FIELD KIT CONVERSION PROCEDURE
The new RESCUE RAIDER Field Conversion Kit is designed to be installed in any upright model game cabinet with a horizontally mounted monitor. Please read these instructions thoroughly before you begin.
Tools Required:
Nut Driver Set Hammer Slotted Screw Driver (medium size) Punch Phillips Screw Driver (medium size) Power Drill Solder Drill Bit Set Soldering Iron Wire Cutter
REMOVAL OF OLD GAME HARDWARE:
1.
2. Turn the power off to your game cabinet and disconnect it from its’ wall outlet.
After opening access door(s) of your game cabinet, remove all existing P.C. boards and their mounting hardware. Discard P.C. boards and mounting hardware except for wood screws that can be reused later. Also remove, and save for reuse, ground straps and their mounting hardware.
After disconnecting Line Cord from existing Power Chassis Assembly remove Power Chassis, ground straps, and mounting hardware. Discard Power Chassis and its' mounting hardware except for wood screws that can be reused later. Also discard ground straps but save their mounting hardware for reuse.
DO NOT REMOVE existing Speaker Cable:
A. If your game cabinet's Speaker Cable is part of existing Master Cable (Wire Harness), do not disconnect these cable wires from existing Speaker. Separate out entire length of these cable wires from Master Cable and then cut wires off at their connections to P.C. board connector of Master Cable. Strip a little insulation from each wire for later splicing and soldering. B. If your game cabinet's Speaker wiring is a separate cable assembly, do not disconnect cable wires from existing Speaker. Cut wires off at connection to P.C. board connector. Strip a little insulation from each wire for later splicing and soldering.
Completely remove your existing Master Cable (Wire Harness) and discard.
Modify existing High Voltage Cable Assembly to be connected to new parts supplied in your kit. Cut off connectors (which did secure to your old Power Chassis) and strip off a little insulation from each wire for later splicing and soldering.
Remove existing Control Panel from your game cabinet. Remove al] controls and wiring from Control Panel. Leave existing unused cable clamps in same positions for reuse. Discard ground strap but save it's mounting hardware for reuse.
- Remove existing Viewing Glass and save. Remove and save existing Monitor Bezel for later sizing of new Monitor Bezel.
- Remove existing Header Attract Art and save for later sizing of new Header Attract Art. :
INSTALLATION OF NEW GAME HARDWARE:
MOTE: Follow the steps below, the illustrations given in Figures 1, 2 & 3 (on pages 10, 11 & 12), the assembly illustrations (on pages 16 & 18), the Wiring Diagrams (on page 19).
- To Install New Parts In Existing Control Panel:
A.
mao Trim new Overlay (supplied in kit) so that it properly covers old Overlay on Control Panel. Slowly and carefully peel heavy waxed backing paper from new Overlay and place over old Overlay on Control Panel. We recommend that center marks shown on new Overlay be used in locating new controls. CAUTION: DO NOT use given center marks for new "ONE PLAYER START" Push-Button Switch and new “TWO PLAYER START" Push-Button Switch. The spacing between them must be wider. DO NOT use given center marks on new Overlay if they conflict with locations of old control holes. Cut out (or drill) necessary holes for mounting of new controls. Secure Control Panel to game cabinet. Install new controls to your newly modified Control Panel as shown in Figure 1 & 2. Mount controls using eight (8) carriage bolts, eight (8) hex head nuts and two (2) Pal nuts from your kit. Route new Control Panel Cable Assembly and solder its' bare wire ends to terminals of new controls as shown in Figure 2 and Wiring Diagram (page 1 of 2). Reuse existing cable clamps.
steering movenent. (see "Joystick Assy: Shaft & Plate "Illustration on
page 18. ° Make sure that when joystick (of either assembly) .is pulled in any diagonal (45°) direction, BOTH switches affected MUST BE CLOSED AT THE SAME TIME. “Reaching the diagonals" on both joysticks is CRITICAL TO PROPER GAME PLAY. Necessary switch adjustment requires bending switch contact leaves so that proper closure by joystick movement is achieved.
Install new Game Play Instruction Card on Front of Control Panel where card wil] be plainly visable and will not block player's view of game.
- Install new POWER CHASSIS ASSEMBLY, new POWER SUPPLY, AUDIO BOARD & MOUNT- ING PLATE ASSEMBLY, and new CARDRACK WITH CPU BOARD ASSEMBLY to inside of your cabinet in locations as suggested in Figure 3. Transformer on POWER CHASSIS ASSEMBLY should be to your left in your cabinet. We recommend that you use #8 wood screws of sufficient length to secure above new assemblies to your cabinet.
- Locate "PIN 1" location label on each one of new Master Cable Assembly connectors you will secure to corresponding P.C. board connectors: P1 & P2 (on CPU BOARD) and J2 (on POWER SUPPLY P.C. BOARD). Do this to avoid making incorrect reversed connections.
- Make certain that a pair of black bare-ended wires (in Master Cable Assembly connected to pin 1 of connector Pl of CPU BOARD) BOTH are secured to your existing Coin Door LIGHT GROUND and SWITCH GROUND.
To install new Master Cable Assembly (refer to Figure 3 and both wiring diagrams):
A. Route new Master Cable Assembly in your cabinet and secure its connectors to assemblies as shown in both wiring diagrams. Reuse existing cable clamps.
B. Referring to both wiring diagrams, solder bare wire ends of Master Cable Assembly to existing Coin Door.
Splice and solder two (2) three foot long wires of new (partial) Speaker Cable Assembly to two bare wire ends of existing Speaker Cable Assembly as shown in Wiring Diagram (page 1 of 2).
Modification of existing High Voltage Cables: Monitor; Header Light; and On-Off Switch (see Wiring Diagram (page 1 of 2) and POWER CHASSIS ASSEMBLY Illustration):
A. Monitor Cabling Modification:
- Crimp pins (supplied in kit) onto three (3) bare wire ends of existing Monitor Cabling and plug each pin into 3 position connector housing (supplied in kit).
- Plug connector P13 into Power Chassis connector J13.
B. Header Light Cabling Modification:
- Crimp pins (supplied in kit) onto three (3) bare wire ends of existing Header Light Cabling and plug each pin into 3 position connector housing (supplied in kit).
° Plug connector P12 into Power Chassis connector J12.
C. New Chassis Power Cable Assembly Installation:
° Plug connector P11 into Power Chassis connector J1l.
a7
10.
lL. Secure existing line cord to tine cord connector on new POWER CHASSIS ASSEMBLY.
A. If they don't match up, cut off and discard existing connector and strip back a little insulation. B. Secure connector of new Adapter Cable Assembly to line cord connector of POWER CHASSIS ASSEMBLY. C. We recommend that you splice each line cord with each Adapter Cable As sembly wire using wire nuts.
MOTE: If your game has an On-Off Switch in line with existing line cord, we recommend that you use modification shown in Wiring Diagram (page i of 2). Splice each prepared On-Off Switch wire with each Adapter Cable Assembly wire using wire nuts.
Installation of four (4) new Ground Straps which are supplied in your kit (refer to Figure 2, Figure 3, and POWER CHASSIS ASSEMBLY Illustration):
A, Secure 48" Ground Strap, 36" Ground Strap, and 18" Ground Strap to POWER CHASSIS ASSEMBLY with hex nut as shown in its' illustration. B. Connect 18" Ground Strap to new CARDRACK WITH CPU BOARD ASSEMBLY. C. Connect 36" Ground Strap to existing monitor. D. Connect 48" Ground Strap, along with additional new 18” Ground Strap, to existing Coin Door's ground. —. Connect other end of 18" Ground Strap to modified Control Panel.
To Install new Header Attract Art:
A. Center old Header Attract Art on new over-sized Header Attract Art. B. Draw a line around outside edges of old Header Attract Art. C. Cut out properly sized new Header Attract Art (trim, if necessary, for accurate fit).
- Discard old Header Attract Art. E. Insta?l new Header Attract Art in game cabinet.
To instal] new Monitor Bezel:
A. Center old Monitor Bezel over new over-sized Monitor Bezel. B. Draw a line around outside edges of old Monitor Bezel. C. Cut out properly sized new Monitor Bezel (trim, if necessary, for accurate fit). D. Discard old Monitor Bezel. E. Place new Monitor Bezel over existing Monitor and set existing Viewing Glass in place.
Referring to “Decal Installation Instructions" on page 13, prepare your cabinet's sides and apply new Side Decals. Place them horizontally at sufficient height.
Close and latch Control Panel.
12.
13.
14,-
15.
16.
17. Close and lock Coin Door.
Check. option switch settings (referring to pages 3 and 4).
Check. option switch settings (referring to pages 3 and 4) Before powering up game cabinet, leave rear access door off. If your’ game
has an. interlock switch, pull it out to its' fully extended position.
Power up game and check Game Operation on Monitor screen and also check Controls.
Color Monitor Screen Adjustments (if necessary):
A. Center the picture, B. Adjust vertical size (height), C. Adjust horizontal size (width).
Make sure the words “SCORE“ (located in upper left corner of screen) and “DIRECTION” (located in upper right corner of screen) do not get “cut off" of Monitor screen.
Close and lock rear access door (after returning interlock switch, if your game cabinet has one, to its normal position).
LEFT “STEERING” RIGHT "SHOOTING" JOYSTICK ASSEMBLY JOYSTICK ASSEMBLY “SPECIAL: WEAPONS® PUSH BUTTON W/CIGHT: OVERLAY
“1 PLAYER” START PUSH-BUTTON
“2 PLAYER’ START PUSH-BUTTON
CARRIAGE BOLT (8 REQ‘D.)
FRONT VIEW
FIGURE 1. SUGGESTED MOUNTING OF NEW
CONTROLS ON EXISTING CONTROL PANEL
-10-}
SOLDER BARE WIRE ENDS TO TERMINALS OF CONTROLS - REFER TO WIRING DIAGRAM
RIGHT “SHOOTING” JOYSTICK ASSEMBLY LEFT “STEERING” JOYSTICK ASSEMBLY
“SPECIAL WEAPONS” , | PUSHBUTTON SWITCH: W/LIGHT EXISTING CABLE CLAMP PAL NUT
NUT: HEX HEAD (8 REQ‘D.) CONTROL PANEL CABLE ASSEMBLY
REAR VIEW “PLAYER 1° PUSH-BUTT' ‘ON SWITCH W/HOLOER
“PLAYERS 1 & 2° PUSH-BUTTON SWITCH W/HOLOER
New: GROUND STRAP | (TO EXISTING
- GOIN DOOR)
FIGURE 2. NEW CONTROL CABLE ASSEMBLY CONNECTED TO NEW CONTROLS ON EXISTING CONTROL PANEL:
-11-|
EXISTING SPEAKER CABLE ASSEMBLY
NEW LINEAR POWER SUPPLY ASSEMBLY
NEW GROUND STRAP FROM NEW POWER CHASSIS ASSEMBLY TO EXISTING MONITOR
CARDRACK W/CPU BOARD
NEW ELECTRONIC POWER CHASSIS
EXISTING LINE CORD EXISTING ON-OFF SWITCH
EXISTING HIGH VOLTAGE CABLE ASSEMBLY
NEW POWER SUPPLY, AUDIO BOARD & MOUNTING PLATE ASSEMBLY
NEW AUDIO 6VB BOARD
NEW GROUND STRAP FROM NEW POWER CHASSIS TO EXISTING COIN DOOR
REAR VIEW
FIGURE 3. PLACEMENT OF NEW ELECTRONIC ASSEMBLIES IN GAME CABINET
DECAL INSTALLATION INSTRUCTIONS
IMPORTANT NOTE:
READ THE FOLLOWING INSTRUCTIONS THROUGH COMPLETELY AT LEAST ONCE BEFORE
ATTEMPTING TO INSTALL THE DECAL(S) THEY CONCERN! !
THE DECAL(S) ARE COMPOSED OF TWO (2) PARTS: 1) A HEAVY WAXED BACKING SHEET WHICH COVERS THE STICKY SIDE OF THE DECAL, AND 2) THE DECAL ITSELF.
Jheinoninckemeccreie® TQ INSTALL THE DECAL(S), PROCEED AS FOLLOWS: *# tiie
BE SURE THE AREAS WHERE YOU ARE GOING TO APPLY THE DECAL IS CLEAN AND FREE OF ALL DIRT, GREASE, AND GRIME.
USING ANY SPRAY-ON GLASS CLEANER, THOROUGHLY WET DOWN THE AREA WHERE YOU INTEND TO PUT THE DECAL.
REMOVE THE HEAVY WAXED BACKING SHEET FROM THE DECAL BY POSITIONING IT FACE UP ON A FLAT SURFACE: GOING TO ANY CORNER; AND BENDING THIS CORNER UP SLIGHTLY TO SEPARATE THE DECAL FROM THE HEAVY WAXED BACKING SHEET.
SLOWLY AND CAREFULLY PEEL THE HEAVY WAXED BACKING SHEET AWAY FROM THE DECAL.
PLACE THE DECAL ON THE GAME CABINET OVER THE WET GLASS CLEANER YOU JUST APPLIED. (THIS WILL ALLOW A SMALL AMOUNT OF FINAL POSITIONING TO BE DONE AFTER THE DECAL IS APPLIED TO THE GAME CABINET.)
SMOOTH THE DECAL.
RESCUE RAIDER UNIVERSAL FIELD KIT - PARTS LIST PART NO. GJ18-00001-0000
QRDER BY PART NUMBER ONLY
PART NO.
AJ18-00005-0000 |CONTROL SHELF CABLE ASSY. DESCRIPTION
AJ18-00007-0000 |MASTER CABLE ASSY.
AJ18-00013-0000 |ON-OFF SWITCH CABLE ASSY.
AJ18-00014-0000 |CHASSIS POWER CABLE ASSY.
AJ18-00009-0000 | SPEAKER CABLE ASSY.
0J18-00900-OOXF |HEADER: RESCUE RAIDER UNIVERSAL FIELD KIT 0J18-00903-0000 |BEZEL: MASK-TV 7 0J18-00901-0000 [OVERLAY: CONTROL SHELF
0J18-00902-0000 |SIDE DECAL (2 REQ'D.)
AC52-00018-0000 |POWER SUPPLY AUDIO BD. & MTG. PLATE (INCLUDES ITEMS 11 THRU 13)
AC52-00007-0000 |POWER SUPPLY & AUDIO BD. MOUNTING PLATE
B006-08002-100B jAUDIO 6V8 8D. ASSY.
8006-08009-1008 {LINEAR POWER SUPPLY BD. ASSY. 4J18-00011-0000 |POWER CHASSIS (W/O LINE CORD) (SEE PAGE 16) L = AC47-00016-0000 |LINE FILTER ASSY. W/PINS 0017-00003-0443 |LINE FILTER: 3-AMP 115V
AB18-00024-0100 |JUMPER PLUG ASSY.: 110 VAC
17 AB18-00024-0200 |JUMPER PLUG ASSY.: 220 VAC
18 0C52-00101-0000 |PLATE: POWER CHASSIS
19 0017-00003-0263 |FUSE: MDA 3AG 250¥ SLOW-BLOW 20 | 0017-00003-0433 |FUSE HOLDER: W/CAP ” 7 21 0017-00042-0685 |BUSHING: SNAP 15/16" 22 | 0017-00042-0686 pes SNAP 1-15/16" 7 AJ18-00012-0000 |CARDRACK W/CPU: (INCLUDES ITEMS 23 THRU 29)
23 AE82-00013-0100 |BRKT.,SHIELD & SPACER ASSY.
RESCUE RAIDER UNIVERSAL FIELD KIT - PARTS LIST, CONT'D. PART NO. GJ18-00001-0000 ORDER BY PART NUMBER ONLY
ITEM DESCRIPTION A084-91889-AJ11 |PROGRAMMED DEDICATED CPU: (INCLUDES ITEMS 24 THRU 29)
24 J11A-12601-0000 |EPROM: 27256-25 POSITION GR-O
25 J11A-12602-0000 |EPROM: 27256-25 POSITION GR-4 Pt i fj
26 J11A-12605-0000 |EPROM: 27256-25 POSITION ROM AB-8
27 JL1A-12606-0000 |EPROM: 27256-25 POSITION ROM AB~12
28 J11A-12609-0000 |EPROM: 27256-25 POSITION ROM CD-8
29 J11A-12610-0000 JEPROM: 27256-25 POSITION ROM CD-12
AJ18-00010-0000 |BAG & HARDWARE ASSY. (INCLUDES ITEMS 30 THRU 44) PLot 30 0017-00032-0093 |SWITCH: WHITE, W/HOLDER (2 REQ'D.)
0017-00032-0150 |SWITCH: SPST PUSH BUTTON W/LITE, RED
0017-00042-0259 |PUSH BUTTON (2 REQ'D.) 0017-00009-0583 |GROUND STRAP - 18" LONG - YELLOW (2 REQ'D.)
0017-00009-0583 |GROUND STRAP - 36" LONG - YELLOW
0017-00009-0595 |GROUND STRAP - 48" LONG - YELLOW
M051~00J18-A012 |LABEL: GAME INSTRUCTIONS 0017-00021-1119 |PIN TERMINALS : M-N-L (10 REQ'D.)
0017-00021-1770 |PLUG (CONNECTOR HOUSING): M-N-L 3-POSITION (2 REQ'D.) 0017-00101-0770 |8-32 X 1-3/4" ROUND HEAD CARRIAGE BOLT (8 REQ'D.)
0017-00101-0802 |#8 X 9/16" UNSLOTTED HEX HEAD W/WASHER SCREW (2 REQ'D.)
0017-00103-0054 |NUT: 5/8 - 11 PAL
0017-00103-0061 |NUT: 8-32 HEX W/SEMS
103E-00003-0005 |1N4004 400V 1 AMP DIODE
100E-00007-0019 |RESISTOR: 270 OHMS 1 WATT
AJ18-00300-0000 |CATALOG & BAG ASSY.: RESCUE RAIDER UNIVERSAL FIELD KIT M051-00J18-AO11 | INSTRUCTIONS: “RESCUE RAIDER UNIVERSAL FIELD KIT M051-00J18-A007 | TAG: OPTION SWITCH SETTING M051-00113-0000 [LABEL: FCC CLASS-A COMPLIANCE
POWER CHASSIS ASSEMBLY PART NO. AJ18-00011-0000
36° GROUND STRAP TO MONITOR
48° GROUND STRAP TO COIN DOOR
CONNECTOR J13
CONNECTOR J11
POWER CHASSIS ASSEMBLY PART NO. AJ18-00011-0000 ORDER BY PART NUMBER ONLY DESCRIPTION ~AB18-00024-0100 |JUMPER PLUG ASSY.: LIOVAC (YELLOW) ‘AB18-00024-0200 {JUMPER PLUG ASSY.: 220VAC (BLUE) AB18-00034-0000 /POWER TRANSFORMER ASSY.: W/PINS AC47-00016-0000 {LINE FILTER ASSY.: W/PINS = 0017-00003-0443 {LINE FILTER: 3-AMP 115V i i ce TAT
AE19-00005-0100 JA.C. SENSE CABLE SUB-ASSY. (NOT SHOWN) | 8 | ocs2-o0101-0000 | PLATE: POWER CHASSIS a
11 | 0017-00042~0685 |SNAP-BUSHING: 15/16" IS 0017-00042-0666 |SNAP-BUSHING: 1-15/16" 10-24 X 10/16" ROUND HEAD, SQUARE NECK BOLT (4 REQ’O.)
p15 0017-00103-0017 |NUT: #10-24 HEX (4 REQ'D.) [16 | 0017-00104-0125 |WASHER: .200" I.D., .562" 0.D. & .032" TH. DISH (4 REQ'D.)
ss‘ PLATE. ° EPART NO. AE36-0002 1-0000.
Reveisinie Actwator
Safety __Cnamber.”
Satety Chamner ‘Satety Chamber
Recess Recess
Reversible Surtace for 8-Way Astivator Joystick
‘Sulace for 4-Way Joystick ;
i
Salety Chamber |
Electronic 4/8-Way Joystick Assembly
Shatt w: Ball (Bally Sente Part No. 0017-00009-0645) Plate w/ Switches (Baily Sente Part No. 0017-00009-0686)
3-5-87 REL. FOR PROD. BALLY/MIDWAY RESCUE RAIDER
Pos
GRO GR4 ABS. AB12 cbs cp12 ROM/EPROM PART NUMBERS H051-00J 18-A008
PART NUMBER
J11A-12601-0000 J11A-12602-0000 J11A-12605-0000 J11A-12606-0000 J11A-12609-0000 J11A-12610-0000
- 7 L 44 ae 43 a whe Brome © om
ail oopeypeyoyys | JOU ene
[es | eee ol tater effete (fe rpe(ye. a
SS LJ 2s J eeP Lo a ca a
M051-00114-A193 X-REFERENCE SMUDGE CPU A084-91889-A000 / PAGE 1 OF 3
| DESCRIPTION | qr. | DESIGNATION | PART NUMBER |
| 74153 | 1 | oF | 0J13-00803-0001 |
| 74F163 | 8 | 5C,6C,14C ,40,4€, |
146 ,L4F ,15F 0913-00803-0002
| 74F174 | 1 | 11D | 0A59-00803-0005 |
| 74374 | 2 | 20, 10€ | 200-00080-0100 |
| 74LS00 | 1 | 9c | 200-00039-0300 |
| 74Ls02 | 1 | 4B | U200-00040-0100 |
| 7ALS04 | 1 | 156 | U200-00041-0100 |
| 74L$32 | 1 | 130 | U200-00043-0100 |
| 7ALS74 | 1 | 13¢ | u200-00044-0100 |
| 74.86 | 2 | 78,88 | 200-00075-0100 |
| 74LS96 | 1 | 140 | u200-00045-0100 |
| 74L$138 | 1 | 136 | U200-00048-0100 |
| 74L$157 | 3 | 30,3E ,4A | 0304-00803-0021 |
| 74LS164 | 1 | 15D | 200-00076-0100 |
| 7ALS174 | 4 | 3A,5B 68,76 | U200-00053-0100 |
| 74LS243 | 1 | 17E | 0J13~-00803-0003 |
| TALS244 | 4 | 138 ,18B ,7C ,18D | 200-00055-0100 |
| 74.8245 | 1 | 16C | U200-00056-0100 |
| 74LS253 | 6 | 60,70,1F ,2F |
3F AF U200-00057-0100
| 74L$257 | 1 | 1A | u200-00078-0100 | |
| 74LS259 | 1 | 126 | u200-00058-0100 | |
| 74LS273 | . | 1 | 2a | U200-00059-0100 |
| 74LS299 | 1 | 15¢ | U200-00077-0100 | |
| 74LS374 | 6 | 8C ,12C ,5D,8D |
5F TF 200-00060-0100
| 74504 | 1 | 10¢ | 200-00063-0100 |
| 74874 | 1 | 120 | U200-00066-0100 |
| 743151 | 6 | 11E,12€,10F ,11F, |
12F ,13F U200-00067-0100
| 748157 | 1 | 160 | 200-00068-0100 |
| 748174 | 2 | L6F ,18F | 41200-00070-0100 |
| 748175 | 2 | 18E ,17F | 0913-00803-0006 |
| 748244 | 3 | 38 ,6F ,8F | 0913-00803-0004 |
| 745374 | 1 | 9B | 0J13-00803-0005 |
| 14049, MOS | 1 | 146 | 210-00005-0100 |
| 14584 ,CMOS | 1 | 66 | 0304-00803-0056 |
| ULN-2003 | 1 | 106 | 260-00002-0100 |
M051-00114-A193 X-REFERENCE SMUDGE CPU A084-91889-A000 / PAGE 2 OF 3
| DESCRIPTION | qv. | DESIGNATION |
| 4416-15 DRAM, 16KX4 | 8 | 18 ,2B,1C,2C ,5E, |
6E ,7€ ,8€
| CY7C168,S RAM, 4KX4 | 1 | 170 |
| X2212 ,NOVRAM,256X4 | 2 | 17C,18C |
| PAL 10L8C | 1 | 1B |
| PAL 16L8A-2 | 1 | 128 |
| PAL 16R6A | 1 | ac |
| PAL 16R6A | 1 | 100 |
| PAL 16R6A | 1 | 15E |
| PAL 16R6A | 1 | 16E |
| PAL 16R6A | 1 | 8G |
| 68A09E | 1 | 168 |
| 68B50 | 1 | 9G |
| 20 MHZ OSC. | 1 | Yi |
| LED | 1 | ps1 |
| 1N914 DIODE | 1 | cL |
| 2N3904 XSTR | 3 | 102,93 |
| 8-P0S. DIP Sw. | 2 | SWI, SH2 |
| IC SOCKET 20-PIN | 7 | 118,128 ,4C, 10D |
15E,16E ,86
| IC SOCKET 24-PIN | 1 | 9G |
| IC SOCKET 28-PIN | 10 | 5A,7A,8A,9A,11A |
12A,13A,15A ,168 18A
| IC SOCKET 40-PiN | 1 | 168 |
| RESISTOR 150 OWM 1/4W | 1 | RI |
| RESISTOR 330 OHM 1/4H | 6 | R11,R13,R15,R17, |
R25,R27
| RESISTOR 1K OHM 1/4 | 10 | R3-R5,R7-R9,R21-R24 |
| RESISTOR 2.7K OHM 1/4W | 1 | R20 |
RESISTOR 3.3K OHM 1/4W 6 R10,R12,R14,R16 R26 ,R28 RESISTOR 4.7K OHM 1/4W 1 R2
| RESISTOR 10K OHM 1/4 | 1 | R6 |
RESISTOR 100K OHM 1/44 2 R18,R19 PART NUMBER
0J13-00803-0008 0313-60803-0007 U230-06007-0100
J13A-12802-0000 J13A-12801-0000 J13A-12803-0000 J13A-12804-0000 J13A-12805-0000 J13A-12806-0000 J13A-12807-0000
U250-00006-0100 U250-00010-0100
0304 -00804-0007 U840-00036-0100 103£-00002-0002 104£-00001-0006 113€-00001-0003
110€-00001-0005 110£-00001-0007
110£-00001-0010 110 -00001-0011
100E -00005-0037
100€ - 00005-0047 100£-00005-0061 LOOE-00005-0072
100£ -00005-0074 100E-00005-0079 100€ -00005-0088 100€-00005-0115
at
M0S1-00114-A193 X-REFERENCE SMUDGE CPU A084-91889-A000 / PAGE 3 OF 3
| DESCRIPTION | Qiy. | DESIGNATION |
| SIP 8-PIN 4X33 | 6 | RP3-4 ,RP8-9 |
RP13,RP15
| SIP 10-PIN 5X33 | 2 | RP1,RPS |
| SIP 10-PIN 9X470 | 2 | RP1L,RPL4 |
| SIP 8-PIN 7XiK | 1 | RP16 |
| SIP 8-PIN 4X1K | 2 | RP1O,RPL2 |
| SIP 10-PIN 9X1K | 1 | RP2 |
| SIP 1O-PIN 5X1K | 3 | RP17 ,RP19,RP21 |
| SIP 10-PIN 5X2K | 3 | RP18, RP20, RP22 |
| SIP 10-PIN 9XLOK | 2 | RPG RPT |
| CAP. CER. AX. .1MF | 124 | C1-C122,C125.C126 |
| CAP. EL. AX. IMF | 1 | C123 |
| CAP. EL. AX. 470MF | 1 | C124 |
| EPROM | 10 | 5A,7A,84,9A,11A,12A, |
13A,154,16A,18A
| RAW PCB | 1 | - |
Rel. for Production 3-12-87 / J.S. PART NUMBER
U460-00015-0100 U460-00016-0100 U460-00012-0100 U460-00014-0100 102E-00004-0046 102£-00004-0013 102E-00004-0047 102E -00004-0048 U460-00013-0100
U300-00009-0100 U340-00015-0100 U340-00018-0100
SEE ROM/EPROM SHEET
A080-91889-A000
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
HBLANK 2— HeLank
to ay Oe a5
uw mo y2 FIs Pt Pt 7 2 % U
1s
2@MHZ« IRE coo 330. jraynne ans Wz ses Brew TORS as Swwb— / swe er Inr8— suase
pz Aw! ssrast ig 33 ax P3 mramnor
os —
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
HBLANK « s4eeND ——>
7HBLANK EMBL Ane MPL ANKE 3 ose
tan HBLArIK a 46 Oe Ay, apa pepe fia ps ry r = & Suz
Zmacanne ——tf>8——— mecanne soa Joc o2ss it 10. 70255 « soa
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
7CoLnam—
/COMPBLANK
cur ln al
7COLRAM
ip] woe soantarkte-: | [es none far Bo]
4x 1orw sie
swes Pr sw3e (3)
swt On al “1 swai (c)
ope cone Tes Tous
3x topin SIP swze (9 PL
@ Pos o1p sw
Vv Tey yy 7
CBANK) ——. “ an Perey canmo ~e ae . as saa ea
eat nose fa 2a] 27258 | 27250 aman
| ase | a Ata ABank: —27 | « | * | |
| WE ff | GAL 2 | 2 | ||
| WAL, | 2 | 2 ot | u | |
| eaa—-—2laa Ne nos a2 jai2 earz—_2 | are | few CeR] ra | ||
| 3] | cars —234 ant | 2a] | 3 | 7 |
| 6a3—3las tant b2— stone 2 | pa | an | i | |
| enz—4he recap! — mvaceaut*? 24] we, eae —2! | jane | t | ||
| 5 | ff | ens 24] | 2a | | tsirs |
| BAI At swe BRYW | ga2 | 7 bad | ||
| Bee Slay /CE a 7NOV | AAS 25, | ‘ed |
BAT 3 dar exc —4 Ine
el fas aa BAZ 3 Az BAZ S| BAL 3 At
| _f Je | sre | ne |
| eas | 13] | ‘ |
| zoe fs OF | 807 | lb? |
| BAI4 | 7cDe | 18 |
| ears 3 [Pewee [ie | ae ta | pe |
| 3 — | aos | bs |
CBANK3 19}
| ; | panes | ape | ba | ssreer |
| CBANK2 | ie pagiz | B03 —!5] | = | ba |
- i nearir al
| xs —# — | 02 | oe |
nannies
| BANK | SABA | eo 12| | Or |
7 ROUSEL “ lor sip Bx C BANKS CBANK2
CBANKI cane ABANKS: ABANK2 ABANKI
ABANKO
[2 [2] FRIOR TO MOUNTING. APPLY HEATSINY COMPOUND TO HEATSINK (ITEM 62) £ HEATSINK (ITEM 70)
TO USE AMI 7688 SHORT PIN1 TO PIN2 OF Uz, Bifeae t
OM gr Ta? stnie Tiomoogs ye a . © ite iess mae (ethan, EE a @® ‘ofa yD 8s) BG rir. «
f ’ ct TT J {2 9
oe % q g & DB Zz z fo) ie z iy iy ANS fl ¢ oes y, AISI ¢ ele | PAR ox QS i] s28Ds &
WITH HARDUARE LITEM 66,67 4 ©@ ) EEFORE SOLDERING TO PCB. FASTEN U0 (ITEM 53) TO HEETSING ITEM 62), LHEATSINK (ITEM TO), AND PCE (ITEM ©), pees
= 8 , B s 1
aneooaoe oon aH \ { voushanas i)
SEE L/M K Tap PROTOTYEE
Diow nF ADDED NOTE 3. REVERSED
OCB ASSEMBLY AUDIO, EVR Mos 1-00¢52-015
QO210 4 EF B] 1924 ADDED 2 HEATSINKS, ITEMS 62 € 70] 25 [UZ
PCB ASSEMBLY, AUDIO 6vB (006-8002-10-08) (4051~00C52-8015) PARTS LIST - SHEET 2 of 4
| THEM | _OFY. | PART NO. | REFERENCE | DESCRIPTION | ||
| 1 | 2 | 400-1001-01 | RL,RA4 | RES, CF,1/4W,58,1K OHM | ||
| 2 | L | 400-6802-01 | 3 | RES,CF,1/4W, 5%, 68K OHM | ||
| 3 | 5 | 400-1083-01 | R4,5,42,45,51 | RES, CF,1/4W,5%, 100K OHM | ||
| 4 | 12 | 400-1004-01 | R6,7,12,13 | RES,CF,1/4W,58,1.0M OHM | ||
| s | 3 | 400-3300-01 | R8,9,11 | RES, CF, 1/4W,5%, 330 OHM | ||
| 6 | 6 | 400-2001-01 | R15-16,17, 20, 22,50 | RES ,CF,1/4W,5%, 2.0K OHM | ||
| 7 | 3 | 400-4701-01 | R25,41,46 | RES,CP, 1/4W, 58, 4.7K OHM | ||
| 8 | 2 | 400-4702-01 | R48, 49 | RES, CF, 1/4W,58,47K OHM | ||
| 9 | 1 | 400-3307-01 | R43 | RES, CF, 1/4W, 5,33 OHM | ||
| 10 | 1 | 401-1005-01 | RAT | RES,CC, 1/4W, 5%, 106 OHM | ||
| lL | 6 | 450-3013-01 | R2/10,14,21, 26,29 | RES, MF, 1/8W, 1%, 301K OHM | ||
| B | 1 | 450-1962-01 | R40 | RES MF, 1/8W,1%,19.6K OHM | ||
| i4 | 1 | 450-2002-01 | R30 | RES, MF, | 1/8W, | «0K OHM |
| 15 | i | 450-4021-01 | Fal | RESSMP,1/Bar18,4,02K oem | ||
| 16 | 1 | 450-1001-01 | R32 | RES ,MF,1/8W, 1%,1.00K OHM | ||
| 7 | 1 | 450-1210-01 | B35 | RES, MF, 1/8W, 18,121 OHM | ||
| 18 | 1 | 450-4990-01 | R36 | RES, MF, 1/8W,18,499 OHM | ||
| 8 | 1 | 450-1002-01 | R39 | RES ,MF,1/8W, 18,10.0K O&M | ||
| 21 | 12 | 330-0005-01 | 14,18,34,38,53, | CAP, PES, RAD, 0.001UF, |
57,71,75,89, 93,119, 100V, 108
| 22 | 6 | 330-0009-01 | €1,15,35 | CAP, PST AKL, 0.002UF, |
54,72, 90 100V, 58
| 23 | 48 | 330-0006-0) | C2,5¢5,749,16,23,25, | CAP,PES,RAD,0.01UF,100V, |
26,27,28,29,30,36,43, 108 45,46,47,48,49,50,55, 62,64.65,66,67,68,69, 73,80, 82,83, 84,85, 86, 87,91,98,100, 101,102, 103, 1C4, 105,126,129,
| 24 | 20 | 330-0007-01 | €20,21, 22,40, 41, 42+ | CAP, PES, RAD, 0.033UF ,100V |
59,60,61,77,78,79,95, 108 96,97, 113,114,123, 124,125
| 25 | 3 | 300-0011-01 | C112, 116,134 | CAP, CER, RAD, 33PF SOV, 108 |
| 26 | 7 | 300-0012-01 | C19, 31,39,58,76,94, | CAP, CER, RAD, 680PF, 50V, 58 |
| 27 | 25 | 300-0002-01 | €3,4,10,12,17,24,32, | CAP,CER,RAD,O.1UF, SOV, 208 |
37,44,31,56,63, 74,81, 92,99, 106,107,109, 110, 111,115,117, 128,
| 28 | 3 | 310-0012-01 | C127, 131,132 | CAP, TAN, RAD, 1, OUF , 25V, 208 |
| 23 | 3 | 340-0016-01 | 8, 11,108 | CAP, ELC,AXL,, 2. 2UP, 63V,50/ |
10% (006-8002-10—-08) (M051-—00C52-B8015) PARTS LIST - SHEET 3 of 4 PCB ASSEMBLY, AUDIO 6VB
| Tra | Ory. | PART NO. | REFERENCE | DESCRIPTION |
| 30 | 6 | 340-0017-01 | C13,33,52,70,88,118 | CAP, ELC,AXL, LOUF , 35V,50/ |
| 31 | 6 | 260-0033-01 | U1, 6,11,16,21,/31 | IC, SP, SOUND, SYNTH ,CEM, |
3394
| 32 | 5 | 210-0007-01 | U24,25,27,28,30 | IC, DIG,CH0S, 4174B,HEX D |
E/E
| 33 | 6 | 210-0006-01 | U3,7,12,17,22,32 | IC, DIG,CM0S, 4051B,8 CHAN |
Mux
| 34 | 1 | 210-0005-01 | U36 | IC, DIG,CMOS , 4049UB,, HEX |
INVERT
| 35 | 1 | 260-0028-01 | U34 | IC,LIN,OPAMP, TLO84,QUAD, |
SPET
| 36 | 1 | 260-0031-01 | 035 | IC,SP,DAC 12 BIT, 7541 |
| 37 | 1 | 260-0007-01 | U3? | IC, LIN, COMP, LM311N |
| 38 | 1 | 260-0037-01 | u33 | IC, LIN,/OPAMP, TLO71,JEET, |
INPUT
| 39 | 1 | 210-0008-01 | 029 | IC, DIG,CMOS, 4503B,HEX TS |
BUEFER
| 40 | 1 | 260-0040-01 | u2 | IC,SP,NOISE SOURCE M45837 |
| 41 | 1 | 200-0039-01 | us | IC, DIG, TTL, 74LS00,NAND |
GATE
| 42 | 2 | 200-0041-01 | u8,13 | IC, DIG, TTL, 741504, HEX |
INVERTER
| 43 | 1 | 200-0043-01 | ul4 | IC,DIG, TIL, 741832,0R GATE |
| 44 | 1 | 200-0044-01 | u23 | IC, DIG, TTT, 74LS74, DUAL |
DE/E
| 45 | 1 | 200-0074-01 | ug | IC,DIG,TIL.,7493,4 BIT |
COUNT
| 46 | 1 | 200-0049-01 | u13 | IC, DIG, TIL, 7418139, 2-4 |
DECODER
| 47 | 1 | 250-0007-01 | U4 | . | IC, DIG,MPU,2-80A | \ |
48 ‘
| 49 | 2 | "240-0005-01 | U10,/15 | IC, DIG, RAM, 6116, 2KX8, |
200NS
| 50 | 1 | 250-0008-01 | u20 | IC, DIG, MPS, 8253-5, TIMER |
| 51 | 1 | 250-0010-01 | U26 | IC, DIG, MPS ,68B50 ,ACIA |
+ 75MHZ
| 52 | 1 | 260-0027-01 | u38 | IC, LIN, VR, 3372, VARIABLE | |
| 53 | 1 | 260-0028-01 | u40 | IC, LIN, VR, 78M0SCT, SV POS | |
| 54 | 1 | 260~-0008-01 | 039 | IC,LIN,VR,7805,5V POS | ; |
| 55 | 4 | 100-0006-01 | D1,2,3,4 | DIO,GR, 50MA, 75PIV, IN34 | |
| 56 | 1 | 550-0062-01 | J5 | CONN 10 PIN LOCKING |
09-74-1101
| 57 | 4 | 510-0019-01 | U10,15,20, 26 | SOCKET, IC, 24P,LOW PRO |
| 58 | 1 | 510-0020-01 | us | SOCKET, IC,28P, LOW PRO |
| 59 | 1 | 510-0021-01 | u4 | SOCKET, IC, 40P, LOW PRO |
| 60 | 1 | 100-0002-01 | 05 | DlO,S1,10MA,75 PIV, IN914 |
PCB ASSEMBLY, AUDIO 6VB .(006-8002~10-0B) (M051-00C52-8015) PARTS LIST — SHEET 4 of 4 REFERENCE
| ITEM | ory. | PART NO. | DESCRIPTION | |
| 61 | 1 | 820-0003-01 | XTL-1 | CRYSTAL 8.000MH2 |
| 62 | 1 | 850-0007-01 | HS-1 | HEATSINK, THM-6070 |
| 63 | L | 310-0015-01 | 120 | CAP, TANT, RAD, 47UF, 15v, |
20%
| 64 | 2 | 400-2703-01 | R33,34 | RES,CF,1/4W,5%,270K OHM |
| 65 | 1 | 400-2700-01 | R52 | RES,CF,1/4W,5%,270 OHM |
| 66 | 3 | 801-0632-06-01 | SCREW PAN HD-PHIL 6-32x |
3/8
| 67 | 3 | 822-0006-00-01 | WASHER SPLITLOCK 6 | |
| 68 | 3 | 816-0632-00-01 | NUT ,HEX,SM PAT, 6-32 | |
| 69 | l | 007-8002-01-0A | PCB, FAB, AUDIO, 6VB | |
| 70 | 1 | 850-0008-01 | HS-2 | HEATSINK, THM-6071 |
FIRMWARE ROM ‘OPTION ROM/RAM +8 a5
Sena 1/0 vee
cst Ve ue * FP St 1001 fg veoe rH, PU Vee @ 00 Tx Data
o
ory
g paral 2
oz
oa
», LS04 SEND
Rec
cord
us mnt (2,08) 0-BUS
U27 On 2 EN AMT
q [sls le - RANA = lo
is wae
$
E on (2,€8)
LH
Biya toy OR
toa 02 IND 2M (2,88)
(2,88) A-8Us
ors ons (2,88)
~AST USED REFERENCE DESIGNATORS: REZ,C134.U40,D5, KTEI-N PH SCHEMATIC, SOUND PC. BOARD
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
are Lornovco|
iy
| ' TAIL C x £-A TYPICAL 4PL (01-04) SCALE! 2/1 . [+] rat ee (1,02) Qa»
2 PL (ez
Qin @ea
NOTES: UNLESS OTHERWISE SPECIFIED (22) 2PL peTaiL B
' APPLY HEATSINK COMPOUND (ITEM 60) ON BOTH SIDES OF INSULATOR (ITEM 78) TYPICAL 2PL (U2, U3» ‘AT QI AND 2, AND ON BOTH SIDES OF INSULATOR (ITEM 77}4T U2 ANDU3. SCALE: 2/1 APPLY BETWEEN HEATSINK AND COMPONENT AT U4,US UG ,01,02,03 AND D4.
ReLeasew ay: WES 5 /4/26_ M05 1-00C$2-8017 ‘OEscRTIO
PCB ASSEMBLY, LINEAR POWER SUPPLY PCB ASSEMBLY, LINEAR POWER SUPPLY (006-8009-10-08) (M051-00C52--8017) . (006-8009-10-08) (4051-00C52-8017) PARTS LIST - SHEET 2 of 3 PARTS LIST — SHEET 3 of 3
| TEM | QTY. | PART NO. | REFERENCE | DESCRIPTION | {TEM | Quy. | PART_NO. | REFERENCE | DESCRIPTION |
| ! | 1 | 00 1-8076-01-08 | HEATSINK , E-368/#5555 | 38 | 2 | 400-2208-01 | RI9,R23 | RES,CF,1/4W,58,2.2 OHM | |
| 3 | 1 | 007-8009-10-0B | PCB FAB, LINEAR PWR SPLY | 40 | 1 | 400-2701-01 | R17 | RES,CF,1/4W,5%,2.7K OHM | |
| 4 | at | 1 | 400-3900-01 | RS | RES,CF,1/4W,5%,390 OKM | ||||
| 5 | 20 | 100-0008-01 | 05-018 ,020-025 | DIO,S1,3A, 100 PIV,MR501 | a2 | i | 400-4701-01 | R14 | RES,CF,1/4W,5%,4.7K OHM |
| 6 | 43 | 2 | 400-4707-01 | R21,R25 | RES,CF, 1/4W, 58,47 OHM | ||||
| 7 | 4 | 195-0004-01 | DI-p4 | DIO,RECTIFIER,16A, | 44 | 1 | 480-0007-01 | Ri2 | RES,VAR,STR,TRIM, 1K OHM |
| MURI610 CT | 45 | 1 | 480-0008-01 | R4 | RES, VAR, STR, TRIM, 100 OHM | ||||
| 8 | i | 110-0004-01 | Dig | D10,ZEN, 5.6V,20MA,1N752A | 46 | 3 | 410-2200-01 | R20,22,24 | RES,CF,1/2W,5%,220 OHM |
| 9 | 47 | 1 | 440-0508-01 | RIB | RES, WW,5W, 108, .05 OFM | ||||
| 7 | 2 | 120-2004-01 | 91,02 | XSTR, $1 ,NPN, 2N3055 | 48 | 1 |
4g
| 12 | ' | 160-0004-01 | SCRI | SCR,8A,50V,CI22F1 | 50 | i | 550-0067-01 | JB | CONN ,PC,4P,M 09-74-1041 |
| '3 | 51 | 1 | 550-0068-01 | J4 | CONN, PC, 5P ,M,22-23-2051 | ||||
| ia | 2 | 260-0039-01 | 4,06 | IC,LIN, SP,TDA2002, AUD AMP | 52 | ||||
| 15 | 1 | 260-0042-01 | U2 | 1C,LIN,VR,MC7912,-12V,, | 53 | 1 | 550-0102-01 | J2 | CONN, PC, 11P,M,09-74-1111 |
| 3 POS | 54 | 1 | 550-0103-01 | S19 | CONN,PC,1IP,M, 10-19-1111 | ||||
| 16 | 1 | 260-0043-01 | U3 | IC, LIN, VR,MC7812,+12V, | 55 | 1 | 550-0110-01 | wy | CONN, PC, 9P ,PLG, 19-09-2099 |
| 3 POS | 56 | 9 | 550-011 1-01 | Jt | CONN,PIN,M,PC,02-09-8113, | ||||
| 7 | 1 | 260-0044-01 | U5 | JC, LIN, VR,MC7815,+15V, | 57 | ||||
| 3 Pos | 58 | 10 | 580-0076-01 | FI-F5S | FUSE,CLIP,PC,1/4" | ||||
| 18 | 1 | 260-0045-01 | ur | 1C,LIN,VR,MC1723,S1, MONO | 59 | ||||
| 59 | 60 | Ark | 790-0007-01 | THERMAL JOINT COMPOUND | |||||
| 20 | 3 | 300-0002-01 | C6,C7,C12,C13,C15,C17, CAP,CER,RAD,. IMF, 50v | 61 | |||||
| €20,C€23,C25 | 62 | 13 | 800-0240-01 | BUSHING , INSULATED ,NYLON | |||||
| 2 | 2 | 300-0001-01 | 24,026 | CAP, CER,RAD, .022UF ,50V, | 63 | 10 | 800-0241-01 | U2-U6 | WSHR,RECTANGULAR, METAL, #6 |
20% 64
| 22 | 1 | 320-0007-01 | co | CAP ,MIC,RAD, 100PF ,500V, | 65 | 4 | 801-0440-04-01 | 01-04 | SCREW, PH,PH,4-40 x 1/4" |
ot 66
| 23 | 67 | 6 | 801-0632-08-01 | 91,02 | SCREW ,PH,PH,6-32 X 1/2" | ||||
| 24 | 4 | 340-0026-01 | ©14,C16,C18,C22 | CAP ,ELC,RAD, 1OMF , 50V ,20% | 68 | 5 | 801-0632-10-01 | —-U2-U6 | SCREW ,PH,PH,6-32 X 5/8" |
| 25 | 2 | 340-0027-01 | _C19,C21 | CAP,ELC,RAD,470MF, 16V, | 69 | ||||
| 10% ,+50% | 70 | 4 | 812-0440-00-01 | D1-D4 | NUT ,HEX,4-40 | ||||
| 26 | 4 | 340-0028-01 | C1A,C1B,CIC,CID | CAP ,ELC,RAD, 10.000MF, 16V | nN | ||||
| +10% ,-30% | 72 | W | 813-0632-00-01 | NUT,HEX , KEP 6-32 | |||||
| 21 | 4 | 340-0029-01 | €3,C4,C10,C11 | CAP, ELC RAD, 6800MF ,25V, | 3 | ||||
| 10%, +308 | 74 | 4 | 830-0019-01 | F2-F5 | FUSE, 3AG,3A,250V, FAST | ||||
| 28 | 4 | 340-0030-01 | €2,C5,C8,C27 | CAP, ELC,RAD, 1000MF ,50V, | ACTING | ||||
| 20% | 75 | 1 | 830-0020-01 | FI | FUSE, 348, 10A, 250V, SLO-BLO |
29 76
| 30 | 2 | 400-1000-01 | R8,RI6 | RES,CF, 1/4W, 5%, 100 OHM | 7 | 2 | 850-0009-01 | U2,U3 | INSULATOR, MICA, TO-220 |
| 31 | 2 | 400- 1008-01 | RI,R2 | RES,CF,1/4W,5%,1 OHM | 78 | 2 | 850-0010-01 | 01,92 | INSULATOR, MICA,TO-3 |
| 32 | 79 | 4 | 850-0011-01 | DI-p4 | HEATSINK,PC MOUNT, VERT, | ||||
| 33 | 2 | 400- 1007-01 | R7,R11 | RES,CF, 1/4W,5%,10 OHM | 0-220 | ||||
| 34 | 80 | 1 | 400-1201-01 | R6*(REV BI) | RES,CF,'/4W,5%,1.2K OHM | ||||
| 35 | 1 | 400-1501-01 | R13,R10 | RES,CF,174W,5£,1.5K OHM | |||||
| 37 | 1 | 400-2200-01 | RIS | RES,CF,1/4W,5%,220 OHM |
- : aw
32 A [i484] PRODUCTION RELEASE. 6 [211996 [RELEASED REDESIGNED PC : fer Genpak +5V +5V
o2 2n3055 40,000 *1-10,000 *1-it,p00 *1-10,000 RI? sev lev we [tev 27K
Fa
R10 Lok NOTES: UNLESS OTHERWISE SPECIFIED i. ALL RESISTORS ARE IN OHMS , Ya, 5%:
+ ALL CAPACITORS ARE IN MICROPARADS.
|. LAST REFERENCE DESIGNATORS USED: R25, €27, D25.U6 ,Q2,F5.JI9, SCRI. HERT SINK ATTACHED TO AUDIO GROUNO
- (#7 = avDIO GND ve
>
i V7 =6N0
{ips qa} —eH2¥ t
i ‘
Fs bav2sov
t + Los io g SOV +lav 3
Vv 4 i —— iS | + cara io
| cia | 20 | f |
10 7
| Tsov | MASOI | i |
-lav 19
+ +15V +12 UNA =— io
| 24 | aLce7 | u | - |
x 1000
| MRSOI | Sov | 2 |
M7 -
MOS 1-00¢52-8018 ASED BY: WES 2/2/s6
SCHEMATIC , LINEAR
POWER SUPPLY
008-6009 -10-G8
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
RESCUE RAIDER U.R.
OPTION SWITCH SETTINGS
SWITCH NO. 1 (SW1) - AT El - LOCATED ON SMUDGE CPU BOARD
TILTATITATTLTAAT ATTA LTT LAT ATT 1 URREOUS GAME PLAY OPTIONS ////////////TI/TTSI ITIL ILTT STL
DURING GAME PLAY: SWH1 SW#2 SHE3 SWE4 SWH5 SWHO SWH7 SW#B NOT NOT USED USED
*-4 LIVES ON EACH COIN 5 LIVES ON EACH COIN 6 LIVES ON EACH COIN 3 LIVES ON EACH COIN
- MINIMUM GAME TIME: 90 SECONDS MINIMUM GAME TIME: 60 SECONDS MINIMUM GAME TIME: 45 SECONDS MINIMUM GAME TIME:120 SECONDS
- KEEP HIGH SCORES ON POWER UP RESET HIGH SCORES ON POWER UP
- MUSIC IN ATTRACT NO MUSIC IN ATTRACT
- INDICATED FACTORY RECOMMENDED SETTINGS PART NO. MO051-00J18-A007
RESCUE RAIDER U.R.
OPTION SWITCH SETTINGS
SWITCH NO. 2 (SW2) - AT E2 - LOCATED ON SMUDGE CPU BOARD TITIHTIITUTTTTTTTTTTTTTT TT LLL TL COINS PER CREDIT TL
VARIOUS CREDIT OPTIONS SW#1 SW#2 SWH3 SWH4 SW#5 SWH6 SWH7 SWHB
FREE PLAY
- 1 COIN / 1 CREDIT 1 COIN / 2 CREDITS 2 COINS / 1 CREDIT 3 COINS / 1 CREDIT
| * NO BONUS COINS | ON | ON ON |
2 COINS ADDS 1 BONUS COIN OFF ON ON
| 3 COINS ADDS 1 BONUS COIN | ON | OFF ON |
4 COINS ADDS 1 BONUS COIN OFF OFF ON
| 4 COINS ADDS 2 BONUS COINS | ON | ON OFF |
5 COINS ADDS 1 BONUS COIN OFF ON OFF
| 5 COINS ADDS 2 BONUS COINS | ON | OFF OFF |
5 COINS ADDS 3 BONUS COINS
- LEFT COIN MECH X LEFT COIN MECH X nue
- RIGHT COIN MECH X RIGHT COIN MECH X RIGHT COIN MECH X RIGHT COIN MECH X Dope
- INDICATED FACTORY RECOMMENDED SETTINGS PART NO. M051-00J18-A007