CATHODE RAY TOMES

GunMen Wars Manual

Gunmen Wars (Japan, GM1 Ver. B) (Namco, 1998) · Manual · 87 pages · 58 sections · original scan

Page 1

Operators Manual

GUNMEN WARS

Namco

Page 2

PORTABLE APPLIANCE TESTING

Please Note:

During testing of the machine with a portable appliance tester the insulation test will show a failure due to the fitting of two VDRs between Live/Earth and Neutral/Earth.

These components have been fitted to safeguard against high voltage surges that may occur on the mains supply to the machine and to comply with the EMC regulations.

To conduct an insulation test on this machine, the VDRs must be isolated from the circuit first.

Ensure that the VDRs are reconnected after the insulation test has been completed and before the machine is placed back into service.

The VDRs used have been specified and tested as safety critical components.

Page 3

SAFETY WARNING

Gun Replacement or Maintenance.

To maintain compliance with CE regulations, the following must be strictly adhered to.

When replacing the gun assembly or refitting the gun sides after maintenance, the four screws located on the gun grip must be Nylon Countersunk Head Screws (M4x12), and the Gun Grip Decals (L & R) must be fitted after the screws have been fully tightened.

Spare screws and decals are supplied with the machine at the time of delivery and must be kept in the machine and available for use at all times.

Nylon c/sunk screw (M4x12)

QQ aN \- : Gun side (R)

Nylon c/sunk screw (M4x12) ( Im grip decal

Page 4

GB) No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of phonographic recording, nor may it be stored in a retrieval system, transmitted or otherwise copied for private or public use, without permission from NAMCO EUROPE LIMITED.

While the information contained in this manual is given in good faith and was accurate at the time of printing. NAMCO EUROPE LIMITED reserve the right to make changes and alterations without notice.

This machine has been manufactured in accordance with European Community Directives, and has been tested and complies with the Directives 89/336/EEC and 72/23/EEC by the application of EN55014-1, EN55014-2 and EN60335-1 standards (see front of manual) and as such bears the € marking. Any changes or modifications to this machine must be in accordance with the European Directives. Any unauthorised changes to this product, may contravene such Directives.

Under some conditions of extreme external interference, e.g. radio transmissions, electrostatic discharge or mains borne transients, some degradation of performance may occur. However the machine will recover normal performance once the source of the interference has ceased or been removed. Following abnormally high surges on the mains supply, the video monitor may need to be manualy reset by turning the machine OFF and back ON

Note:- If the game processor resets due to an interuption or reduction of the mains voltage any credits established may be lost.

This game is not a machine as defined by the Machinery Directive 89/392/EEC

SAFETY WARNING

In order to use this machine safely, be sure to read this Operators Manual carefully before installation, adjustment or use of this machine.

Whenever the owner of this machine entrusts dis-assembly, installation, adjustment or routine maintenance to another person, the owner should ensure that that person read the appropriate precautions and relevant sections of this manual before starting work.

In order that no accidents occur when the machine is in operation, strictly follow the notes on safety as described below.

This manual along with the Installation Manual (where applicable) form an integral part of the equipment and must be available to the operating and service personnel at all times.

This machine is for indoor use only and should only be used for the purpose intended.

Namco Ltd. bears no responsibility for accidents, injury or damage resulting from unauthorized changes to, or improper use of thi chine.

SAFETY NOTES

The following safety notes are used throughout this manual. Familiarize yourself with each of these notes and its meaning before installing, servicing or making adjustments to this machine

WARNING /\ Warning denotes a hazard that could result in injury or death. Do not proceed beyond a warning note until the indicated conditions are fully understood and met.
CAUTION (1) Caution denotes a hazard that could result in damage to the machine. Do not proceed beyond a warning note until the indicated conditions are fully understood and met.

GENERAL SAFETY CONSIDERATIONS

Only operate this machine after checking that it has been installed correctly and in accordance with the manual.

Parts of this machine move during game play, so there are places where the distance between the stationary section and moveable section changes. There are warning notices to keep hands and feet clear of moving parts, however if the operator feels that a person is in any danger, he should warn that person accordingly.

The warning notices must always be kept in good condition and replaced if worn, so that customers can read them clearly.

If there is an error or problem with the machine, operation must be stopped immediately and the problem rectified before any further use.

Installation, service, adjustment or routine maintenance should be carried out by suitably qualified persons only.

For continued protection against fire hazard, replace fuses with the same type and rating. The use of other fuses or material is prohibited.

The power supply inside the monitor will remain hot and have areas of high voltage even though the machine has been turned OFF, and there is the possibility of burns or electric shock. Be careful not to touch these areas.

To prevent possible electric shock due to failure, this machine MUST be fitted with a securely connected EARTHED plug.

If at any time the mains supply lead becomes damaged, it must be replaced immediately.

Do not turn the power switch ON until the machine has been installed correctly. OPP BP BPBBBPBP BB

Before connecting the machine to the mains supply, ensure that the machine is set for the correct voltage and that the correct fuses are fitted.

Page 5

( NOTES ON INSTALLATION )

Z\ NEVER turn the power to the machine ON until installation has been completed. Boone cmanenl

A In order to prevent possible electric shocks, be sure that the machine is connected to the mains with a securely connected earthed plug.

A So that customers are not injured by the movement of the P q machine, ensure that there is as least 500mm separation between other machines or walls.

© In order to avoid damage to the machine due to mis-operation, ensure that the voltage of the mains supply is 230volts AC. Paying zone

Note: If the location of this machine has a polished floor, it is recommended that rubber pads are fitted under the level adjusters to prevent the machine sliding on the floor.
Note: In order to gain access to the Power Supply and CPU assemblies, make sure that the rear of the machine is separated from a wall or other machine by at least 500mm. Va Ne

MOVING THE MACHINE

This machine is fitted with castors to make it easier to move. Take care when moving the machine on an inclined surface.

The Header Assembly has a forward centre of gravity, so it is important that at least two people are used to fit or remove the Header Assembly.

The fitting position of the Header Assembly is high, and it is important that a means of reaching the height safely,without stretching, is available. (e.g. Steps, Step Stool etc.)

The overall height of the machine, overhead obstructions. (e.g. Light the Header Assembly fitted, is 2080mm. Take care of any ittings, Electric Cables etc.) > BP BP BP B&B

When moving the game, ensure that the game is dis-assembled into 3 parts: Monitor Assy, Ride Assy and Header Assy.

REMOVING AND REPLACING PARTS Adjustments or maintenance on this machine should be carried out by suitably qualified personnel only.

Do not make any alteration to this machine without prior approval. Doing so could cause unforeseeable

danger.

Only parts specified by Namco Europe Ltd should be used when replacing or repairing parts. (Including screws).

Ensure that the power to the machine is turned OFF before commencing any maintenance work. (Trouble shooting, repairs etc.)

If performing work not described in this manual, be sure to contact your distributor for instructions, as no responsibility will be accepted for damage or injury.

Parts of the Power Supply and Monitor remain hot and carry high voltage even after switching OFF and could cause burns or electric shock. Take care not to touch these parts accidentally. > BP BP BP BP BP B

Make sure that the machine is switched OFF before connecting or disconnecting any plugs or connectors.

Z\ When removing the mains connector from the machine, or the mains plug from the wall outlet, always Ne S

Page 6

Dieses Dokument darf in keiner Weise vervielfaltigt werden. Jegliche Tonaufnahmen sowie die Speicherung auf Datentrager (Suchsysteme), die Weitergabe oder sonstiges Kopieren fur den gewerblichen und privaten Gebrauch sind untersagt und bediirfen der vorherigen Genehmigung durch NAMCO EUROPE LIMITED.

Die informationen in diesem Handbuch entsprechen den Tatsachen bei Drucklegung. NAMCO EUROPE LIMITED behalt sich jedoch das Recht zu Anderungen ohne vorherige Bekanntgabe vor.

Dieses Gerat tragt das CE-Zeichen und wurde gem den EU-Richtlinien produziert. Es erfillt die Richtlinien 89/336/EEC und 72/23/EEC und Standards EN 55014, EN55104 und EN60335-1 (s. Deckblatt des Handbuches). Alle Verainderungen an diesem Gert miissen in Ubereinstimmung mit den EU-Richtlinien erfolgen. Nicht genehmigte Veranderungen an diesem Gerat verstoRen gegen diese Richtlinien.

Extreme AuRere Stérungen, wie z.B. durch Radiobetrieb, elektrostatische Entladung oder zeitweilige Netzschwankungen kénnen zu einer Leistungsminderung fuhren. Sobald diese Faktoren jedoch ausgeschaltet oder beseitigt wurden, erreicht das Gert seine normale Leistung.

Achtung! Falls der Spielprozessor auf Grund von Netzunterbrechungen oder Abnahme der Netzspannung aussetzt, kann es zum Verlust von Spielkrediten kommen.

Dieses GerAt fallt nicht unter die Maschinen-Richtlinie 89/392/EEC

SICHERHEITSHINWEISE

Um einen ordnungsgemafen Betrieb dieses Gerates zu gewahrleisten, mu8 vor Aufstellung, Inbetriebnahme und Gebrauch das Handbuch sorgfaltig gelesen werden. Sobald der Besitzer dieses Gerdtes die Demontage, Aufstellung, Inbetriebnahme oder den Service einer anderen Person iibertragt, mu er sicherstellen, daB diese Person vor Arbeitsbeginn die ndtigen Sicherheitshinweise und die dazugehérigen Kapitel des Handbuches liest und versteht. Um jegliche Unfaille wahrend des Betriebes zu vermeiden, miissen obige Hinweise strikt befolgt werden. Dieses Handbuch sowie das spezielle Gerate-Handbuch (wenn vorhanden) gehéren zum Gerat und missen dem Betreiber und Wartungspersonal stets zuganglich sein. Dieses Gerat ist ausschlieBlich fur den gewerblichen Gebrauch in geschlossenen Réumen bestimmt und darf nur dort betrieben werden NAMCO LTD. tibernimmt keinerlei Haftung fur Unfalle, Verletzungen oder Beschadigungen, die auf nicht genehmigte Verainderungen oder unsachgemafen Betrieb des Gerates zurlickzufiihren sind.

SICHERHEITSHINWEISE

Folgende Sicherheitsbegriffe werden im gesamten Handbuch benutzt. Machen Sie sich daher bitte vor Inbetriebnahme, Wartung und Durchfuhrung von Einstellungen am Gerat mit diesen Wamhinweisen vertraut.

WARNUNG /\ WARNUNG bezeichnet eine Gefahrenquelle fiir Leib und Leben. Erscheint dieser Warnhinweis, darf erst weitergearbeitet werden, wenn die entsprechenden Erklarungen vollstandig verstanden und befolgt wurden.

VORSICHT (0) VORSICHT bezeichnet eine Gefahrenquelle fiir die Beschadigung des Gerates. Erscheint dieser Warnhinweis, darf erst weitergearbeitet werden, wenn die entsprechenden Erklérungen vollstandig verstanden und befolgt wurden

ALLGEMEINE SICHERHEITSHINWEISE

Das Gerat darf nur betrieben werden, nachdem es vorschriftsmaRig und in Ubereinstimmung mit dem Handbuch aufgestellt wurde.

Das Gerat bewegt sich wahrend des Spielbetriebes, somit verandert sich der Abstand zwischen feststehenden und beweglichen Teilen. Warnschilder verweisen darauf, fiir Hande und FiiRe einen gebiihrenden Sicherheitsabstand einzuhalten. Sobald eine Person in Gefahr ist, mu der Betreiber sie warnen.

Die Warnschilder miissen in gutem Zustand sein und ersetzt werden, wenn sie nicht mehr gut lesbar sind.

Bei Auftreten eines Fehlers oder Problems muB das Gerat sofort abgeschaltet werden und darf erst nach fachgerechter Behebung des Fehlers wieder in Betrieb genommen werden.

Aufstellung, Service, durchgefiihrt werden. ‘instellungen und Wartung diirfen nur von dafiir qualifiziertem Fachpersonal

Zur Vermeidung von Feuer, defekte Sicherungen nur durch vorgeschriebene Sicherungen ersetzen. Die Verwendung von andersartigen Sicherungen oder unterschiedlichem Material ist untersagt.

Das Netzteil im Monitor bleibt nach Ausschalten des Gerates noch hei& und fiihrt weiterhin Hochspannung. Daher besteht die Gefahr von Verbrennungen und Elektroschlagen. Diese Bereiche diirfen nicht berihrt werden.

Zur Vermeidung von Elektroschlagen mu dieses Gert mit einem ordnungsgemf geerdeten Netzstecker versehen seii

Bei Beschadigungen des Netzteiles muf dieses umgehend ersetzt werden.

Gerat erst nach abgeschlossener Aufstellung einschalten. OP PEP BBB BE BB

Vor Einstecken des Netzsteckers bitte sicherstellen, da& Netzspannung und Geratespannung Ubereinstimmen, und die vorgeschriebenen Sicherungen verwendet wurden.

Page 7

Va

A

A

A

©

Hinweis:

Hinweis:

Ne HINWEISE ZUR AUFSTELLUNG

NIEMALS das Gert einschalten bevor die Aufstellung vallig abgeschlossen ist.

Zur Vermeidung von Elektroschlagen mu8 das Gerat mit einem ordnungsgemaf geerdetem Netzstecker an die Stromversorgung angeschlossen werden.

Um zu vermeiden, da& Kunden durch die Geratebewegungen verletzt werden, mu ein Sicherheitsabstand zu anderen Geraten und Wanden von mindestens 50cm eingehalten werden.

Zur Vermeidung von Beschadigungen durch Fehibetrieb am Gerdt sicherstellen, da die Netzspannung 230 Volt betragt.

Ist das Gerat fiir einen Aufstellplatz mit glattem Fu@boden bestimmt, missen die Standbeine mit Gummiplattchen unterlegt werden, damit das Gert fest steht und nicht auf dem Boden hin- und herrutscht.

Zu Reparaturzwecken am Netzteil und den CPU-Komponenten mu die Rickseite des Gerates mindestens 50cm von anderen Geraten und der Wand entfernt sein.

Fa PBR BB B- Zum leichteren Transport ist das Gerat mit Rollen ausgeriistet. Daher besondere Vorsicht auf abschiissigem Boden

Der Schwerpunkt des Aufsatzes liegt sehr weit vorn. Daher werden fiir den Ab- und Aufbau des Aufsatzes mindestens 2 Personen bendtigt.

Der Aufsatz wird in groRer Héhe montiert. Daher mu aus Sicherheitsgriinden eine Steighilfe, wie z. B. eine Leiter, ein Tritt oder ahnliches, verwendet werden.

Die Gesamthohe de Gerates betragt 2.08m. Daher Vorsicht bei tiefer hangenden Beleuchtungskérpern.

Fir den Transport oder bei einem Platzwechsel Gerat in drei Teile zerlegen: Kopfteil, Vorderteil, und Fahreinheit

~

(pep >PBPBPB BB

AUS- UND EINBAU VON KOMPONENTEN UND TEILEN

Aufstellung, Service, durchgefiihrt werden. ‘instellung und Wartung diirfen nur von dafiir qualifiziertem Fachpersonal

Es diirfen keierlei Veranderungen ohne vorherige Genehmigung am Gert vorgenommen werden. Zuwiderhandlungen stellen eine Gefahrenquelle dar.

Fir die Repartur diirfen nur Originalersatzteile (incl. Schrauben) von NAMCO EUROPE LTD. verwendet werden.

Vor Beginn aller Wartungsarbeiten (Fehlersuche, Reparaturen etc.) muf der Netzstecker gezogen werden.

Bei Arbeiten, die nicht in diesem Handbuch beschrieben werden, mu8 vorher der Handler zu Rate gezogen werden, da sonst keinerlei Haftung bei Beschadigungen und Verletzungen ibernommen wird.

Teile des Netzteiles und Bilschirmes bleiben nach Abschalten noch heif§ und fiihren Hochspannung. Dies kann zu Verbrennungen oder einem Elektroschlag fiihren. Diese Teile diirfen nich beriihrt werden.

Vor der Montage oder dem Entfernen von Steckverbindungen und Steckern muB das Gerat ausgeschaltet werden.

Bei Ziehen des Geratesteckers oder des Netzsteckers aus der Wandsteckdose stets den Stecker

greifen und nicht das Kabel. yy

Page 8

Denne udgivelse ma ikke reproduceres af nogen som helst mekanisk, fotografisk eller elektrornisk proces eller i form af indspilning, den ma heller ikke lagres i et eftersogningssystem transmitteres eller kopieres til nogen form for offentlig benyttelse uden tilladelse fra Namco Europe Limited.

Da informationerne i denne manual er givet med god tro og var korrekt pa udskivningstidspunktet, forbeholder Namco Europe Limited sig retten til, at foretage eendringer og forandringer uden varsel.

Denne maskine er frernstillet i overensstemmelse med Det Europziske fzllesskabs direktiver og er blevet testet og fuldendt med direktiverne 89/336/EEC og 72/23/EEC standarder (se manualens forside) og som sadan beerer CE meerket. Enhver form for zendring eller modiflkation af denne maskine skal vzere i overensstemmelse med Det Europaziske fallesskabs direktiver.

| tilfeelde af forbigaende ekstreme eksterne forstyrrelser, s& som radio udsendelser, elektronisk afgivelse eller forstyrrelser pa ledningsnettet, kan nedbrydning forekomme. Maskinen vil dog kore normalt s& snart forstyrrelsen ophorer eller bliver fjernet.

Bemzerk:- Hvis spilleprocessoren resetter p.g.a. en forstyrrelse eller reduktion af hovedstrammen kan de etabledrede kreditter ga tabt.

Dette spil er ikke en maskine defineret af maskin direktivet 89/392/EEC -

SIKKERHEDS ADVARSEL

For at betjene denne maskine sikkert, les da denne brugemanual grundigt for installation, justering eller brug af maskinen. Nar som helst ejeren af denne maskine overlader demontering, installation, justeringer eller daglig vedligehold til en anden person, skal ejeren sikre sig at denne person lzser de sikkerhedsregler og relevante punkter i denne manual for arbejdet begynder. For at undga ulykker nor maskinen er i gang, folg noje de sikkerhedsregler der er beskrevet herunder. Denne manual sammen med installations manualen er en uloselig del af udstyret og skal altid veere til raidighed for det arbejdende og servicerende personale. Denne rnaskine er kun til indendors brug og bor kun bruges til det beregnede formal Namco Ltd. baerer intet ansvar for ulykker eller skader som er et resultat af uautoriserede zendringer eller fejlagtig brug af denne rnaskine.

SIKKERHEDSREGLER

De folgende sikkerhedsregler er brugt helt igennem denne manual. Gor dig bekendt med hver enkelt af dem og meningen heraf for installering, servicering eller justering af denne maskine.

ADVARSEL A Advarsel betegner en episode der kan resultere i skader eller dod. Begiv dig ikke forbi et advarselsskilt for de indikerede betingelser er fuldstandig forstaet. FORSIGTIG (7) _ Forsigtig betegner en episode der kan resultere i odeleeggelse af maskinen. Begiv dig ikke forbi et advarselsskit for de indikerede betingeser er fuldsteendig forstaet.

GENERELLE SIKKERHEDSOVERVEJELSER

Betjen kun maskinen efter at have tjekket, at den er korrekt installeret og er i overensstemmelse med manualen.

Dele af denne maskine er i beveegelse nar den korer sa der er steder hvor afstanden mellem den stationzre og den bevegende sektion endrer sig. Der er advarselsskilt om, at holde hander og fodder vek fra de beveegelige dele, dog skal lederen straks advare en person han foler der er i fare.

Advarselsskiltene skal altid vere i god stand og erstattes hvis de er slidt, sa kunden tydeligt kan lease dem.

Hvis der er en fejl eller et problem med maskinen skal betjening straks stoppes, og problemet afhjzlpes for yderligere brug.

Installations service, justeringer eller daglig vedligehold bor kun udfores af en kvalificeret person.

For fortsat beskyttelse mod brandfare, sikres at hoved sikringerne kun erstattes med samme type kapacitet. Brug af anden kapacitet eller materiale er forbudt.

Stromforsyningen inde 1 monitoren vil forblive varin og have omrader med hoj spending selvom maskinen har veret slukket og der er fare for brandskader eller elektrisk stod. Pas pa med at rore disse omrader.

For at undga elektrisk sted p.g.a. en fejl skal denne maskine vzre forbundet med et sikkert jordstik.

Hvis hoved ledningerne pa noget tidspunkt bliver beskadiget skal de strakt erstattes.

Tend ikke for strommen for maskinen er korrekt installeret.

For tilslutning af maskinen til hovedstrammen sikres, at maskinen er indstillet til den rette spaending. OBPBB B BBB Be BB

Page 9

OB BBE

BEMERK : Hvis denne maskine placeres pa et poleret guly, anbefales det at PUNKTER OM INSTALLATION

Tzend aldrig for strommen til maskinen for installering er fuldfort.

For at undga mulige elektriske sted sikres, at maskinen er forbundet til hovedstrommen med sikkert monterede jordstik.

For at kunder ikke kommer til skade ved spillets bevagelser sikres, at der er mindst 50cm afstand til andre maskiner og vegge.

For at undga skader pa maskinen p.g.a. fejlbetjening sikres, at spzendingen pa hovedstrommen er 230 volt AC.

Paying zone ligge gummimatter under justeringsfadderne for at undga at maskinen glider pa gulvet.

BEM/ERK : For at fa adgang til stromforsyningen og CPU justeringer sikres, at bagsiden af hoved kabinettet star adskilt fra andre maskiner eller veeggen med mindst 50cm.

> Maskinen er smurt med olie for at gore den lettere bevaeegelig. Pas pa nar maskinen flyttes pa en skra overflade.

Hoved sektionens forreste center er meget tung, det er derfor vigtigt, at mindst 2 personer benyttes til at montere el. flytte hoved sektionen.

Monterins hgjden af hoved sektionen er meget hgj og det er vigtigt, at have hjzlpemidler til at na sikkert uden at skulle straekke sig. (fek.s. trapper, trappestole el. lign.).

Den fulde hojde af hoved sektionen er 2.08 m. Pas pa ovre forhindringer f.eks. lys inventar.

Nar spillet skal flyttes eller bares skal det sikres at den er demonteret i 3 dele: - Hoved sektion - Front sektion - Kore sektion

PRP BBP BP PBB AT FJERNE OG UDSKIFTE SEKTIONER OG DELE.

Justeringer eller vedligehold af denne maskine ber kun udfores af kvalificeret personale.

Skift ikke noget pa maskinen uden godkendelse, det kan fare til uforudset fare.

Der ber kun bruges dele specificeret af Namco Europe Limited nar der skiftes eller repareres dele (inklusiv skruer).

Sorg for, at strommen til maskinen er slukket for der foretages nogen form for arbejde (fejlfinding, reparation etc.)

Hvis der foretages arbejde der ikke er beskrevet i denne manual, kontakt da din leverandor for at fa kyndig vejledning, da intet ansvar vil blive accepteret ved skader.

Dele af stramforsyningen og monitoren forbliver varme eller bwrer haj spznding selv efter maskinen er slukket, det kan fore til forbrazendinger eller elektriske stad. Pas pa ikke at rore disse dele ved et uheld.

Lag merke til at maskinen er slukket for samlinger eller stik tages ud eller szttes i.

Nar hovedsamlingen fjernes fra maskinen eller hovedstikket fjernes fra vaeggen, tag da altid ved stikket, ikke ledningen.

Page 10

© No se permite la reproduccién total ni parcial de esta publicacién por ningun medio mecanico, fotografico o electrénico, grabaciones fonograficas, ni su almacenamiento informatico, su transmisién o su copia, ya sea para uso ptblico o privado, sin permiso de NAMCO EUROPE LIMITED.

Si bien la informaci6n contenida en este manual se da de buena fe y es correcta en el momento de su impresion, NAMCO EUROPE LIMITED se reserva el derecho de hacer cambios y alteraciones sin previo aviso.

Esta maquina ha sido fabricada segun las directrices de la Comunidad Europea, ha sido probada, y se ajusta a las directrices 89/336/EEC y 72/23/EEC, mediante la aplicacién de los estandares EN65014, EN65104 y EN60335-1 (véase cubierta del manual) y por ende lleva el sello de la C.E. Cualquier cambio 0 modificacién que se haga a esta maquina ha de ajustarse a las directrices de la Comunidad Europea. Cualquier cambio no autorizado hecho al producto pudiera contravenir estas directrices.

Bajo ciertas condiciones de extrema interferencia externa, p. ej. transmisiones de radio, descargas electrostaticas u oscilaciones de la red eléctrica puede tener lugar un descenso del rendimiento. No obstante, la maquina recuperara su rendimiento normal una vez que la fuente de interferencias sea retirada o cese de producirlas.

Nota: Si el procesador de juegos se reinicializa a causa de caidas o interrupciones en la alimentaci6n eléctrica, se perderan todos los créditos.

Este juego no se ajusta a la definici6n de maquina de la Normativa de Maquinaria 89/392/EEC

AVISOS DE SEGURIDAD.

Para utilizar esta maquina con seguridad, lea cuidadosamente este Manual de Operador antes de proceder a la instalacién, ajuste o uso de esta maquina. Cada vez que el propietario de esta maquina confie a terceros su desmontaje, instalacién, ajuste 0 mantenimiento rutinario debera asegurarse de que tales personas lean las precauciones adecuadas y las secciones relevantes de este manual antes de comenzar su trabajo. Para que no ocurra accidente alguno mientras la maquina se encuentre en funcionamiento, siga estrictamente las notas de seguridad tal como mas adelante se describen. Este manual, junto con el Manual de Instalacién (cuando proceda), forma parte integral del equipo y debe estar a disposicién del personal de mantenimiento y operacién en todo momento Esta maquina es nicamente para ser usada en interiores, y slo debe usarse para aquello para lo que ha sido creada. Namco Ltd. queda exenta de cualquier responsabilidad por accidentes, heridas 0 dafios causados por cambios no autorizados 0 uso indebido de esta maquina.

NOTAS DE SEGURIDAD.

En este manual se usan las notas siguientes. Familiaricese con cada una de ellas y su significado antes de instalar, revisar, o hacer ajustes en esta maquina

AvISO. /\ Aviso sefiala un riesgo que puede ocasionar lesiones o la muerte. Tras ver esta nota, no continue hasta entender completamente y cumplir las condiciones exigidas. PRECAUCION. (0) Precaucién sefiala un riesgo que puede ocasionar dafios a la maquina. Tras ver esta nota, no continue hasta entender completamente y cumplir las condiciones exigidas.

CONSIDERACIONES GENERALES DE SEGURIDAD.

> Opere sélo con esta maquina tras comprobar que ha sido instalada correctamente y de acuerdo con este manual.

> Algunas partes de esta maquina se mueven durante el juego; por tanto, hay lugares en que la distancia entre las secciones méviles y estaticas cambia. Existen notas de aviso indicando que se mantengan manos y pies alejados de las partes méviles. No obstante, si el operador cree que cualquier persona se encuentra en peligro, debe advertir de ello a dicha persona.

Las notas de aviso deben mantenerse siempre en buen estado y reemplazarse si estuvieran desgastadas para que los usuarios puedan leerlas con claridad.

Si hubiera algun error o problema con la maquina, debe interrumpirse su operacién inmediatamente, y subsanar el problema antes de volver a usarla.

Las revisiones de instalacién, los ajustes, y el mantenimiento rutinario deberan llevarse a cabo sélo por personal cualificado.

Para asegurar una continua proteccién contra riesgo de incendios, aseguirese de que los fusibles eléctricos sean reemplazados solamente por otros del mismo tipo y especificaciones. El uso de otros fusibles o material esta prohibido.

La fuente de alimentacién del monitor se mantiene caliente, y tiene zonas de alto voltaje incluso cuando la maquina ha sido desconectada, existiendo el riesgo de quemaduras y descargas eléctricas. Tenga cuidado de no tocar estas zonas.

Para evitar posibles descargas eléctricas por cortes, esta maquina debe estar provista de un enchufe debidamente conectado, con TOMA DE TIERRA.

Si en cualquier momento el cable de alimentacién se dafiara, deberé ser reemplazado inmediatamente.

No encienda el interruptor de la maquina hasta que ésta haya sido correctamente instalada.

Antes de enchufar la maquina a la red eléctrica, asegurese de que la maquina esta preparada para el voltaje correcto, y de que se usan los fusibles adecuados. OPP EP BP BBB

Page 11

O FP BB

Notas :

Notas : NOTAS DE INSTALACION.

JAMAS ENCIENDA la maquina antes de haber completado la po instalacion. | Para evitar posibles descargas eléctricas, asegurese de que la 4 maquina esta conectada a la red con un enchufe provisto de toma de tierra. i>] Q

Para que los usuarios no sufran lesiones debido al movimiento del juego, asegurese de que hay al menos 500 mm de separacién entre éste y otras maquinas o las paredes. Para evitar dafios a la maquina causados por operaci6n incorrecta, aseguirese de que el voltaje de la red es de 230 voltios, corriente alterna. Pajeg xno Si el lugar donde se instalara la maquina tiene un piso pulido, se recomienda colocar tacos de goma bajo los ajustadores de nivel para evitar que la maquina se deslice por el suelo.

Para acceder a las unidades de Fuente de Alimentacion y CPU, asegurese de que la parte trasera del mueble principal esta separada de muros u otras maquinas al menos 500 mm.

El juego tiene ruedecitas para hacer mas facil su traslado. Tenga cuidado al mover la maquina en una superficie inclinada.

La Unidad de Igualaci6n tiene el centro de gravedad desplazado hacia adelante. Es importante que su montaje y desmontaje se haga por al menos dos personas.

La posici6n de la Unidad de Igualacion es bastante alta, y es importante que haya un medio de alcanzar su altura con seguridad, sin estirarse (p. ej. una escalera, un taburete, etc.)

La altura total de la Unidad principal es de 2.08 mm. Tenga cuidado de que no haya obstaculos p. ej. luces.

Cuando traslade o mueva el juego, asegurese de que éste haya sido desmontado en 3 partes: Unidad de Igualacién, Unidad Frontal, y Unidad de Juego. w

> BP BPBBB PB B RETIRAR Y REEMPLAZAR PARTES Y UNIDADES. >

Las revisiones de instalacién, los ajustes, y el mantenimiento rutinario deberdn llevarse a cabo solo por personal cualificado.

No realice alteraciones en esta maquina sin aprobacién previa. De hacerlo asi, pueden causar peligros imprevisibles.

Solo deben usarse las partes especificadas por Namco Europe Ltd. para reparaciones o reemplazos (incluidos los tornillos).

Asegirese de que la maquina esta desconectada antes de comenzar cualquier trabajo de mantenimiento (reparaciones, resolucion de problemas, etc.)

Al realizar trabajos no descritos en este manual, pongase en contacto con su distribuidor para recibir instrucciones. Se declina cualquier responsabilidad por dafios o lesiones.

Hay partes de la fuente de alimentacion y del monitor que se mantienen calientes o almacenan alto voltaje incluso tras desconectar la maquina, y pueden producir quemaduras o descargas eléctricas. Tenga cuidado de no tocar accidentalmente estas partes.

Asegiirese de que la maquina esta apagada antes de conectar o desconectar cualquier enchufe o conector.

Al retirar el conector principal de la maquina, o la clavija de alimentacion del enchufe de la red, agarre siempre la clavija y no el cable. yy,

Page 12

© Aucun élément de cette publication ne sera reproduit, ni par procédé mécanique, photographique ou électronique, ni par un moyen d'enregistement phonographique. Ces informations ne seront ni stockées grace a un procédé de récupération, ni transmises ou autrement copiées pour un usage publique ou privé, sans l'autorisation de NAMCO EUROPE LIMITED.

Malgré le fait que les informations contenues dans ce manuel soient données de bonne foi et étaient actualisées au moment de leur impression, NAMCO EUROPE LIMITED se réserve le droit de procéder & des changements ou a des modifications sans avis préliminaire.

Ce jeu a été fabriqué en respect des normes de la Communauté Européenne, aprés avoir été testé il repond aux normes 89/336/EEC et 72/23/EEC, en application des standards EN55014, EN55104 et EN60335-1 (voir la couverture du manuel), et comme tel il comporte l'autocollant de conformité avec les normes de la Communauté Européenne. Tout changement non autorisé sur ce produit pourrait contrevenir & ces normes.

Sous certaines conditions extrémes d’interférence exteme, par example des transmissions radio, des décharges électrostatiques ou bien de interférences passagéres sur le réseau, certaines dégradations ou anomalies peuvent se produire. Le jeu retrouvera cependant son état normal de fonctionnement lorsque la cause de ces anomalies aura cessé ou se trouvera déplacée.

Note:- Si le processeur du jeu se reprogramme suite a une interruption ou une réduction de l’alimentation, les crédits qu'il aurait pu contenir peuvent se trouver perdus.

Ce jeu n'est pas une machine, telle que définie par la norme sur les machines 89/392/EEC

MESURES DE SECURITE

Afin d'utiliser ce jeu en toute sécurité, bien lire ce manuel d'utilisation avant de procéder a son installation, son réglage ou son exploitation. Si le propriétaire de ce jeu en confie la démontage, installation, le réglage ou la maintenance habituelle A une autre personne, il devra s'assurer que cette personne ait lu les conseils d'utilisation et les passages du manuel se rapportant a ce théme, avant qu’elle ne commence son travail. Afin d’éviter tout accident pendant la durée d’exploitation de ce jeu, se conformer strictment aux conseils de sécurité décrits a la suite. Ce manuel ainsi que le manuel d'installation du jeu (la o nécessaire) font partie des éléments nécessaires a I'installation de la machine et doivent étre mis a la disposition de l'utilisateur et du personnel de maintenance a tout moment. Ce jeu est uniquement destiné a un usage intérieur et devra étre utilisé comme tel Namco Ltd. ne sera aucunement tenu responsable en cas d’accidents, de blessure ou de dommage quelconque résultant de modifications non autorisées ou d’'usage impropre du jeu.

REMARQUES SUR LA SECURITE

Les termes de sécurité détaillés a la suite seront utilisés tout au long de la lecture de ce manuel. II convient de vous familiariser aves chacun de ces termes ainsi que leur signification avant de procéder a installation, & la maintenace ou au réglage du jeu

AVERTISSEMENT /\ Ce terme annonce un danger qui pourrait éventuellement avoir des conséquences dommageables ou mortelles. Ne pas passer oiltre ce signal jusqu’a ce que les conditions indiquées soient entiérement comprises et effectuées.

ATTENTION © Ce terme indique qu'un danger menace la machine. Ne pas passer oiltre ce signal jusqu’a ce que les conditions indiquées soient entiérement comprises et effectuées.

CONSIGNES GENERALES DE SECURITE

A\ Allumer l'appareil seulement aprés avoir verifié qu'il a été correctement installé, et que les instructions du manuel ont été respectées

> Certaines piéces du jeu bougent quand jeu est en fonctionment, il y a donc des endroits oui la distance entre la zone stationnaire et la zone en mouvement change. Il existe des notes de mise en garde pour les mains et pieds sur les piéces en mouvement. Cependant si l’opérateur pense qu’une personne court un danger, il doit I'en avertir.

Les notes de mise en garde doivent constamment demeurer en bon état et tre remplacées en cas de disparition, afin que le client puisse les lire clairement.

S’il y una erreur ou un probléme avec la machine, l'utilisation doit étre immédiatement interrompue et le probleme résolu avant toute nouvelle utilisation.

L’installation, le service, le réglage, ou la maintenance doivent étre effectués uniquement par les personnes qualifiées.

Afin d’éviter un éventuel incendie, s'assurer que les fusibles soient remplacés par le méme type de fusibles et au bon voltage. L'utilisation d'autres sortes de fusibles ou autres matériels est interdite.

L’alimentation a l’intérieur du moniteur reste chaude et comporte des zones de haute tension méme si la machine est éteinte. Il existe donc un risque de brulure ou d’électrocution. Attention a ne pas toucher ces endroits.

Pour prévenir une éventuelle électrocution due a un défaut matériel, ce jeu DOIT étre muni d’une prise de TERRE connectée en toute sécurité

Si a tout moment les fils électriques sont endommagés, il faut les remplacer immédiatment

Ne pas mettre le jeu en mode de fonctionnement avant qu’il n’ait été correctement installé. OPP BBBB PB

Avant de connecter la machine au réseau, s’assurer que la machine est installée sous la bonne tension et que les fusibles correspondent.

Page 13

> BB

(3)

Note:
Note: NOTES D’INSTALLATION

NE JAMAIS mettre le jeu en marche avant que l'installation ne soit complétement effectuée.

Afin de prévenir une éventuelle électrocution, s'assurer que la ->— machine est connectée au réseau avec une prise de terre reliée selon les normes de sécurité.

Afin que les clients ne soient pas blessés par les mouvements du jeu, s'assurer qu'il existe au moins 500 mm de séparation aves les autres jeux ou les murs. Ty Ww Afin d’éviter que la machine ne soit abimée suite a une mauvaise opération, s'assurer que la tension sur le réseau principal soit de 230 volts AC. Praying zone

Si lendroit ou doit étre installée la machine a un sol pdli, il est recommandé de poser des tampons feutrés sous les vérins pour éviter que le jeu ne glisse sur le sol

Afin de facilité 'accés aux CPU at a l'alimentation, s‘assurer qu'il y a

un espace d’au moins 500 mm entre l'arriére du meuble et le mur ou tout autre jeu.

(> pppep) Le jeu est foumi avec des roulettes pour une meilleure mobilité. Prendre garde quand la machine est déplacée sur une surface inclinée.

Le centre de gravité de la partie supérieure du jeu est situé sur l’avant, il est donc indispensable que deux personnes au moins soient employées pour installer ou déplacer la partie supérieure.

L'installation de la partie supérieure du jeu s’effectue en hauteur, il est donc important d’utiliser un élevateur quelconque pour en effectuer le montage.

La hauteur totale de l'assemblage principal est de 2080 mm, prendre garde aux encombrements de la partie supérieure (ex : illuminations du bandeau).

Quand le jeu est déplacé ou transporté, s'assurer qu'il est séparé en 3 parties: l'assemblage du haut (le bandeau), l'assemblage de devant (la cabine), l'assemblage mobile.

PRP BBB PPB BE DEPLACER ET REMPLACER LES UNITES ET LES PIECES DETACHEES.

L'installation, le service, le réglage, ou la maintenance doivent étre effectués uniquement par les personnes qualifiées.

Ne pas apporter de modifications sur cette machine sans autorisation préalable, faute de quoi cela pourrait entrainer un danger.

Seules les piéces détachées Namco Europe Ltd. doivent étre utilsées pour le remplacement ou la réparation de piéces (y compris les vis)

S'assurer que l'interrupteur soit sor OFF avant de commencer tout travail de maintenance (localisation d'une panne, réparations, etc.)

Si dans ce manuel il manque une information pour réaliser un quelconque travail, contacter votre distributeur, car aucune responsabilité ne sera acceptée en cas de domage ou de blessure.

Les piéces de |’alimentation et du moniteur restent chaudes, a tension élévée méme lorsque la machine est hors tension, elle pourrait occasionner des brilures ou des électrocutions. Attention de ne pas toucher ces endroits accidentellement.

S’assurer que la machine soit hors tension avant de brancher ou débrancher toute prise ou connecteur.

Lorsque l'on manipule la prise au réseau de la machine, ou lorsque les prises principales doivent étre débranchées, saisir toujours la prise, et non le cable.

Page 14

Kavéva pépos autiig TS EkSoons Sev pMopei va AVEMEpaXGei He ONOLOSHMOTE LNXAVIKd ,pwToyPAgtKd Hh NAEKTPOVIKO HEGO , H LE LOPHH GwvNTiKi\g NXoyPapNaNG Kal OUTE Va aNOONKEUTEl UE eravopewTIKo GUoTHLG , va Hetadobei H va avttypadgel via SnHdIa F (StwtiKA XENON , Xwpig THY Gdeta Tag NAMCO EUROPE LIMITED. Ka®dg autéc ot MAnpogopies Ge aUTS To eyxeIpidio ExouV do8ei ple KAAH MioTH Kal aKpIBds THY GPa TH TUMWONS , n etaipeia NAMCO EUROPE LIMITED kpatdet To Sikaiwpa va Kavet onoieddrmote aAAayés Xwpig elSortoinon.

Ta unxavijwata éxouv Katackevaotei GUE wva Le Tous dpous tng Eupwnaikrs KowoTnTas , Kat éXxouv eheyxOel GUL>wVA [Le ToUC vouoUs 89/336/EOK kat 72/23/EOK we tv aitnon twv EN55014 , EN55104 Kat EN60335-1 otdvraptc (Sec [NpooTa oto eyXelpidio) Kal Oda EXoUV To CE ofa . Onoadinote adAayn fi LeTatpom} de aUTS To UNXaVvNLA Mipénet va eivat OULwva Ue Tous dpous tHg Eupwnaiki\s KowvoTHTaG. OntoteddhMoTe adAayés Xwpig GdEla Ge AUTO To MipOldv UMopEi va TapaBei autots Tous dpous. Ze KaNOLES MepINTdoEIg UTMEPBOAIKIIG EEWTEPIKIIG MapPELBOArS JILX. PAdIOpwvikés HETAddaEIG , NAekTpoOTATIKés etaBoAgs F MapodiKé¢ EUBoAss , uNopei va MapoudiactoUy Kanoleg ABALOTHTES GTRY apouGiaan . Navtwo' to LnXavnua’Ga erravéAGel otHY PUGIOAOYIKH] MapoUGiacn e doov N MY!) TNS TapELBOANS oTaLaTHoEt 1 artoyakpuveei .

Znyeiwon : Eav yivet reset otov processor Tou uNnXavnaTos KATA TH Siapkela THS KUPLas MapoOxN¢ , MOvTOL TOU Sxouv Kepdneei ynopel va xaGouv.

Auto To naixvidi Sev eivat UNXavNuA drws NpoddiopizeTat and Tous Spoug MnXavnuaTwv 89/392/EOK . OAHTIEZ AZ@AAEIAE Tia ty aogad} Xpijon Tou NXavnpaTog , Mpénet va SiaBagerg To eyXeIpidto XphaNS NpoceKTIKa TplV THY eyKaTéataon ,tonoBEtnaN H XPron TOU LNXavnyaTos. OnotedHnote 0 LioKTHING AUTO Tou UNXAVILATOS TNTdEl aNd Karolo MPSoWNO va EYKATACTIOEL , va KavEt onoiadrnote aAAayi} 1 EdeyXo poutivag oto ~NXAavnHA , Mpértet va eivat ciyoupos ti Exel SiaBaoet Tig odnyies autoU Tou eyxelpidiou npiv va apxicet va SouAEvet . Mog anopuyny onoiouvdinote atuxiatos Kata THv Aettoupyia Tou UNXaviHATOS , aUoTNPdS akoACUBOUVTAL ot odnyieg agparstag Srwe divovtai Mapakatw . AUTO TO eYXEIPIOLO GE GUVSUAOLS LE TO EYXEIpIdI0 eyKaTaoTaaNG (dmoU StaTiBetTal) anoteAsi Eva CAOKANPWHEVO HEpog Twv TapoXdy Kat Mipéntet va eivat diaGEo\No ya THY Aettoupyia Kal To service onoladrMOTE OTLYLN. AuTé To unXavnia eivat yia XpHOn [OVO Ge EGWTEPIKS XHPO Kal Ga TIPENEL Va XoNG\LOMOLEITAL [Ovo yia ToUG AdYoUG yia Tous ontoiouc KatackeudomKe. H_ staipeia NAMCO Ltd dev dépet Kapia eu8UvN yia aTUXi\WaTA , MAnyés 1 KaTaoTPOPES TOU UTOpE! va MPOKANBoUY ané adAayés Xwpig eta Ge 1 etoaywyeig auTOU Tou UNXavijyaToS.

ZHMEIOZEIZ AZMAAEIAL

O1 akddouses oNHEIdoEIG aopadeiag XoNOIOTIOLOdVTaI HEoW aUTOU ToU eyxXElpIdioU . AtGBace auTés TIPOGEKTIKG Vid va Yivel KaTavoNTS To VoNHA Tous TPL THY eyKaTdoTaGN , GEpBIG h OMOIGdHMOTe GAAayh yivet oto ynxavnya.

MIPOEIAONOIHSH /\ H npozidonoinon apopa Kivduvo 0 onoiog umopei va eival Adyos BavaTou . Na unv Mpoxwphoeig oe ono1adinoTe Kivnon HEXPI aUTOI o1 Spor yivouv KaTavonToi.

NPOZOXH (0) H mpoaoxi) apopa Kivéuvo o onoiog propel va npoKadgoet NpOBANYA oto pNXavnya .

E=ETAZH TENIKHE AZ@AAEIAL

Agou éxe1 KatavonOei aur To eyXsipidio , Havo TOTE va AcITOUPYHOE! To HNXavNHG A va yivel EdeyXos Eh 60ov éxe1 yiver n eyKaTaoTaon.

Mépn Tou unXaviyaTos HETaKIVoUVTal KaTa THY SiapKela evo NaIXvIdI0U , éToI WoTe va UNdpXoUV Hépn oroU 1 anootaan WeTaEU TOU HépouG oTaBYEUONG Kal ToTIOU Kivnons va HTOpEi va GAAAZE! . YTapxouV Tpoeidoroingeig va sivai Ta Xépia Kal Ta MOSIa PaKPIG ano Ta WEpN NOU KIVOUVTaI, OYwS o IdIOKTATHS NpéTE va ehéyXel EGV KaTIOIOG KIVSUVEUEI Va TOV EISOTIOINGE! Kal Va TOV aToYaKpUVE! .

1 mpoeidoronjoeig mpéne! va pévouv KaBapéc Kal Ge KAAH KaTaoTaON Hore o MEAATHS va Tig SiaBazet ka@apa.

Eav umapxe! Ad@oc f MPOBANHG Pe TO WNXavNYG , Nn ActToupyia Mpéne! va oTapaTae! apéows Kal va SiopOdvetai To AGVoc Mplv ono1adiMoTe GAAN XpHON.

Eykataoraon , wetatpom fh éAeyXog poutivag ynopsi va yiveta! pdvo and efoucioSotnpEva toa .

Tia ouvex Tpootacia and pwrid , npéne! of aogadcies va avtiKa®ioToUVTal He idloU TUNOU .H Xxpijon GAAwY aogaAciav avTiKeINévwv anayopeusral.

To Tpopodotikd oto eowrepiKd Tou UNXavAHATS 8a Mapapsivel Geos Kal UTaPXoUV TEpIoXés HE UYNAA Tan nap’oAo nou To uNXavnya dev SouAsdE! , Kal UNapXe! N MIBaveTHTG NAEKTPIKOU GoK . MpogoxH va UNV AkOULTAGEIG UTES TIG MEpIOXES.

Tia THY artoguyn NAEKTpIKOV GoK Adyo BAGBNG , To "NXavqa MIPENE! va éxe1 npdta evwOei pe yeiwon.

Eav Karola oniyyi KaTaotpadei n KUpia Tapoxi , NpéTe! va avtiKaTaoTaesi apsows.

Na pny avawer to nxavnua (switch ON) yéxpl va éxel eyKaTaoTaGei GwoTd Kal TARPWS. OBPBPP BBB BBP BB

Now tv napoxh pevpatog oto UNXavnua , va eioat ciyoupos StI Ta voltage Kal dAEg ot aapadetes civat cwotd evwéva Kal TOro@etTnHEVva.

Page 15

~

> EP BE

o)

\ ZHMEIOSH: Eav to natwya oto onoio eivat tomoBeTnHEVO To ENXavnHa

ZHMEIOZH: fa mv eUKOAN NPdoBaon oTHV KUpiwG TapoXH i TO CPU ZHMEIOQZEIZ FIA THN ET KATAZTAZH |soenernre Spenerman

NOTE va pnv avaBei To pnxavnya eav Sev éxe1 oAOKANPweEI 1 eykaTaotaon.

Tia thy anoguyh nAeKtpIKdv GoK Mpéme! TO HNXaVvNHG va éxeI ye1w6ei.

Tia thv anoguyn Kivuvou of KaTolov naiktn , Mpéme To unxavnna va éxe1 andotaen TouAaXicTov 500mm ané aAAo uNxavnya 1 Toixo.

Tia Thy anoguyi) BAGBY oT UNXavNUA Adyo AGBog AetToUpyiag , MIpsTEL N TapoXy} va eivat 230volt AC.. Praying zone

YAuoTpaeL.eival KAAS Va UTeL Eva KOMHATL WOKETaG Yia anoguyh petakivnons tou ENXaviHatos ev dpa Rettoupyiag Tou.

Rpénet n Tiow Ndpta Tou ENXavnYATOS va anéxet ToUAaXIToV 500mm and Tov ToiXo f GAAO UNXavnua.

>b>BeP BBB To ynxavnua sivar epodiacpévo pe KapouAIa yia THY EUKOAN HETaKivNGH TOU.

To enavw pépog Tou uNXavNHaTos éxeI eMIMAZov Bapog yiauTs xpElaGovral Suo yia Thy HETAgoPA.

H kegaAq (kamaki) Tou WNXaviHATOG eival TOAD WNAS Kal ylauTd xpElaZeTa! MpoToX! OTHV Tomo@éTHOH Tou , va PNY XTUTMGE! f KaTaoTpAgEi.

To GUVOAIKS Uyos THs KEMadiic eival 2080mm . Spavtice va NV XTUTTHGEI Ge AdyTES K.A.T.

‘Orav petaxiveital To WNXavqHG , Mpénel va cival oe 3 HépN: Kegadh (Kanak), Mmpoora pépos (o@6vec), Kasiopa

bP B BBP BRB BBE ANOMAKPYNEH KAI ANTIKATAZTAZH MEPON - ANTAAAAKTIKON

Eykaraotaon , petatpomi # éAeyXog poutivag ynopsi va yivetal Hove amd sEouaIodoTHHEVa aTopA.

Aev npénei va yivovrai petatponés ora unXaviiyata wpig éyKpion . Mnopei va mpoKAn@si anpéBAentog Kivduvos.

Mévo pépn mou SieuKpivifovtai ané Thv etaipeia NAMCO EUROPE Ltd pmopouv va XPNGipoToInBouv yia avTiKkaTdoTaon f EMId1OpAwon. (GuuTEpIAaBavovTe Kal o1 BidEc)

Na sivai ciyoupa KAsioré To pupa Tiplv onoladAMoTe SouAEIa GTO WNXavnuG. Eav yiver Kanio1a SouAeia oro ynxavnya Xwpig va SieuKpivizeral To eyXeipidio , va emKolvwvagels He Tov avtinpéawno yia odnyies ylati Kapia EvedvN Sev HEpouyE yla KaTaoTpOpss f BAGBES.

Mépn Tou Tpopodorikou H Tou PdvITop Mapapévouy ZeoTa H sXoUV UNA Taon akoya Ka! OTaV OBAoEI To UNXavNYA Kal HMOpOUY va TPOKGAEGOUV KAWIHO f AEKTPOGOK.TiaUTS Sev Mpénel va Epxovrai of enagh pe xépia «

To ynxavnya mpénel va eival oBnotd Kata Thy ov3Ean A aTocuvdEon MpIZag H KOVEKTOpA.

Kata Thy amopaKpuvon Twv KeVTpIKOV KovéKTop aNd To LNXavAHG A TNS KUPiag MpIZag , NpéTE! va TIGVOUHE TO TAGOTIKO HEpOG Kal OXI TO KGAGSIO.

Page 16

a Nessuna parte di questa pubblicazione pud essere riprodotta con processo meccanico, fotografico o lettronico, né sotto forma di registrazione fonografica, nd pud essere memorizzata in un sistema di salvataggio, trasmessa o in altro modo copiata per uso pubblico o privato, senza l'autorizzazione di NAMCO EUROPE LIMITED.

Le informazioni contnute in questo manuale sono state date in buona fede ed erano accurate al momento della pubblicazione. Tuttavia NAMCO EUROPE LIMITED, si riserva il diritto di apporre cabiamenti e variazioni senza alcun preavviso. Questo apparecchio é stato costruito in conformita alle Direttive della Comunita Europea, ed @ stato provato e soddisfa le Direttive 89/336/EEC e 72/23/EEC per l'applicazione degli standards delle norme EN55014, EN55104 e EN60335-1 (vedi fronte del manuale), e per questo porta il marchio CE. Qualsiasi cambiamento 0 modifica di questo apparecchio deve essere in conformita con le Direttive della Comunita Europea.

In caso di condizioni di estrema interferenza dall'esterno, per esempio trasmissioni radio, scariche elettrostatiche o transitori sulla linea, pud verificarsi un decadimento delle prestazioni. Comunque l'apparecchio ritornera al rendimento normale quando la sorgente dell,interferenza avra cessato di emettere o sara stata rimossa.

Nota bene: se il processore del gioco “resetta” a causa di una interruzione o diminuzione del voltaggio di linea, un eventuale credito, gia concesso, pud essere annullato.

Questo goco non é una macchina cosi come viene definita dalla Direttiva Macchine 89/392/EEC.

AVVERTENZE PER LA SICUEZZA

Allo scopo di usare questo apparecchio in sicurezza, leggere questo Manuale dell’operatore attentamente prima dell’installazione, regolazione 0 uso di questa macchina Tutte le volte che il proprietario di questo apparecchio affida lo smontaggio, l'installazione, la regolazione o la manutenzione ordinaria ad un’altra persona, il proprietario stesso deve assicurarsi che quella persona legga le precauzioni necessarie ¢ i paragrafi importanti di questo manuale prima di iniziare a lavorare. Perché non succeda alcun incidente quando la macchina é operante, seguire rigorosamente le note sulla sicurezza come specificato piu avanti. Questo manuale insieme con il manuale di installazione (dove si pud applicare) forma una parte integrante dell’apparechio e deve essere disponibile sempre al personale operante e di servizio. Quest macchina deve essere usata solo in interni e deve essere usata solo per gli scopi per cui é progettata. Namco Europe Ltd non si assume responsabilita per incidenti, ferite o damni risultanti da cambiamenti non autorizzati o da uso improprio della macchina.

NOTE PER LA SICUREZZA

Le seguenti note sulla sicurezza sono usate dal principio alla fine di questo manuale. Valutare attentamente ciascuna di queste note ed il loro significato prima di installare, fare assistenza o regolazioni su questa macchina.

WARNING /\ “Warning” evidenzia un rischio di ferita 0 di morte. Non procedere oltre una nota “Warning” finché le avvertenze specifcate non siano completamente capite e conosciute.
CAUTION (2) — “Caution” evidenzia un rischio di danneggiare la macchina. Non proceder oltre una note “Caution” finché le awertenze specificate non siano completamente capite e conosciute.

CONSIDERAZIONI GENERALI SULLA SICUREZZA

Mettere in funzione l’apparecchio solo dopo aver controllato che |’installazione sia stata effettuata correttamente ed in conformita alle istruzioni del manuale.

Parti di questa machina si muovono durante il gioco, quindi ci sono posti dove le distanze tra la parte fissa e quella mobile cambiano. Ci sono avvisi “Warning” di tenere mani e piedi lontani dalle parti mobili, comunque se Voperatore crede che una persona sia in un qualche pericolo, deve avvisare quella persona.

Gli avvisi “Warning” devono sempre essere conservati in buone condizioni e sostituti se consumati, cosicche il cliente li possa leggere chiaramente. Se vi sono errori o problemi con la macchina, si deve interrompere il funzionamento immediatamente e risolvere il problema prima di ogni ulteriore uso.

L’installazione, l'assistenza, le regolazioni e la manuzenzione ordinaria devono essere eseguite solo da persone idonee e qualificate.

Per una protezione costante contro il rischio di fuoco, assicurarsi che i fusibili sulle alimentazioni siano solo sostituiti con lo stesso tipo e caratteristiche. L’uso di altri fusibili o materiali é proibito.

L’alimentatore all’interno del monitor rimane caldo ed ha zone di alto voltaggio anche se la macchina é stata spenta, c’é quindi la possibilita di bruciature o scosse elettriche. Fare attenzione a non toccare queste zone.

Per prevenire possibili scosse elettriche dovute a difetti, quest macchina DEVE essere installata con un connettore sicuramente MESSO A TERRA.

In caso il cavo di alimentazione di rete risultasse danneggiato deve essere sostituito immedatamente.

Non accendere la macchina finché la stessa non é stata installata completamente e correttamente. OPP BPBBBPBPBP BB

Prima di collegare la macchina alla rete, assicurarsi che la machina sia preparata per il voltaggio corretto e che siano inseriti i fusibili adatti.

Page 17
Note: NOTES D’INSTALLATION

NON ACCENDERE MAI la macchina finché l'installazione non@ = 2"="8* evens stata completata.

Allo scopo di prevenire possibili scosse elettriche, la macchina deve essere obbligatoriamente collegata alla rete con un connettore messo a terra con connessioni sicure.

Perch i clienti non siano feriti dal movimento del gioco, assicurarsi che ci siano almeno 500mm di distanza rispetto alle altre macchine o rispetto al muro.

Per evitare danni alla macchina durante la messa in opera, assicurarsi che il voltaggio della rete sia 230 volts AC. Praying zone Il uogo di destinazione della macchina deve avere il pavimento liscio e si raccomanda di sistemare dei cuscinetti di gomma sotto i piedini di livellamento per prevenire lo sciovolament della machina sul pavimento.

Per garantire l'accesso all’alimentatore e alla scheda madre, assicurarsi che il retro del mobile principale sia separato dalla parete 0 da altre macchine di almeno 500mm.

~\ ll gioco é fornito di ruote per rendere pit facile il suo spostamento. Fare attenzione quando si muove la macchina su una superficie inclinata.

La testata ha il baricentro spostato in avanti, é percid importante che ci siano almeno 2 persone per montare o smontare la testata stessa.

La posizione di fissaggio della testata é molto alta, ed é importante che ci sia un mezzo disponibile per raggiungere tale altezza in sicurezza e senza allungamenti. (Ad esempio scalini, scale portatili etc.)

L’altezza totale della parte principale é 2080mm, fare attenzione ad eventuali ostacoli sopra la testata ovvero ad eventuali installazioni di luci.

Quando si muove o si trasporta il gioco assicurarsi che sia smantato in 3 parti: Testata, Parte frontale, Parte mobile S

PP BBBBB BE > RIMOZIONE E SOSTITUZIONE DI GRUPPI E PARTI STACCATE

L'installazione, l’assistenza, le regolazioni e la manuzenzione ordinaria devono essere eseguite solo da persone idonee e qualificate. Non apporre alcuna modifica alla macchina senza autorizzazione preventiva. Il fare questo pud causare un pericolo non prevedibile.

Quando si rimpiazza o si riparano delle parti (incluse le viti) si possono usare solo parti approvate dalla Namco Europe Ltd

Assicurarsi che la macchina sia SPENTA prima di incominciare qualsiasi lavoro di manutenzione (guasti, riparazioni etc.)

Se state per iniziare un lavoro non descritto in questo manuale, contattate il vostro distributore per instruzioni poiché non si accetta alcuna responsabilita per danni o ferite. Parti dell'alimentatore e del monitor rimangono caldi o portano alta tensione anche dopo aver spento V'apparecchiatura e possono causare bruciature o scosse elettriche. Attenzione a non toccare queste parti accidentalmente.

Assicurarsi che la machina abbia l'interruttore nella posizione OFF prima di inserire o disinserire qualsiasi connettore o spina.

Quando vengono rimossi i connettori principali dalla macchina oppure la spina dell’alimentazione dalla parete bisogna sempre afferrare il connettore e non il cavo. w

Page 18

@)

Ingen del av denne utgivelsen ma reproduseres av noen mekaniske, fotografiske elle elektroniske prosesser, eller i form av fotografiske opptak, og ikke kan det lagres i et gjenvinnbart system, sendt eler kopiert for offentlig eller privat bruk, uten tillatelse fra NAMCO EUROPE LIMITED.

Da informasjonen i denne manualen er gitt i god tru og var korrekt da den ble utgitt, tillegger NAMCO EUROP LIMITED seg retten til A lage forandringer uten varsel.

Denne maskinen er produsert i samsvar med direktiver framsatt av det Europeiske samfunn. Maskinen er testet og samsvarer med direktivene 89/336/EEC og 72/23/eec med anvendelse av EN55014, EN55104 og EN60335-1 standarder (se i begynnelsen av manualen), og derfor beerer CE merket. Hvilken som helst forandring eller modifisering ma skje etter direktivene satt av det Europeiske samfunn. Uautoriserte forandringer pa dette produktet, kan motstride disse direktivene.

Under noen forhold av ekstreme ytre forstyrrelser, f.eks radio sendere, elektronisk utladning eller transiente spenninger, kan man regne med noe senket ytelse. Men maskinen vil oppna normal ytelse nar kilden til forstyrrelsene opphorer eller er fysisk fjernet.

Merk:- Hvis spillets prosessor resettes p.g.a et kutt eller reduksjon av hovedspenningen kan oppsparte kreditt pa spillet forsvinne.

Dette spillet er ikke en maskin som er definert ved Maskin direktivet 89/392/EEC.

Sikkerhets advarsel.

For 4 bruke denne maskinen uten noe form for fare, sorg for lese denne manualen noye for installasjon, justeringer eller bruk av maskinen. Nar eieren av denne maskinen overlater avmontering, installasjon, justering eller rutine vedlikehold til en annen person, skal eieren forsikre seg om at denne personen leser de passende forsiktighetsreglene og relevante deler av manualen for han starter p& arbeidet. For a forhindre at ulykker inntreffer nar maskinen er i drift, folg strengt teksten om sikkethet som beskrevet nedenfor. Denne manualen sammen med installasjons manualen (hvor det er anvendelig) er en intrigert del av utstyret og ma veere tilgjengelig for drift- og servispersonell til alle tider. Denne maskinen er bare for innendors bruk og skal bare benyttes etter mente hensikter. Namco Ltd. beerer intet ansvar ved ulykker, kvestelse eller skade som folge av uautoriserte forandringer, eller for uriktig buk av maskinen.

Sikkerhets beskjeder.

Folgende sikkerhets punkter er brukt ut denne manualen. Gjor deg kjent med disse punktene og deres mening for installasjon, service eller du utforer noen innstillinger pa denne maskinen.

ADVARSEL /\ Advarsel innebeerer en risiko som kan fore til kvestelse eller dod. Ikke fortsett utover advarsien for den er ordentlig forstatt og mottiltak er igangsatt. FORSIKTIG (1) _ Forsiktig innebeerer en risiko som kan medfore skade pa maskinen. Ikke fortsett utover advarslen for den er ordentlig forstatt og mottiltak er igangsatt.

Vanlige sikkerhetstiltak.

Bruk bare denne maskinen etter 4 ha kontrollert at den er korrekt installert ifolge manualen.

Deler av denne maskinen er i bevegelse under spill, det er derfor plasser hvor avstanden mellom de stillestaende deler og bevegelige deler forandres. Det er plassert skilt med advarsel for 4 holde hender og fotter borte fra bevegelige deler, men uansett skal operatoren varsle vedkommende hvis han foler at han er i noen form for fare.

Advarsel skiltene ma bestandig holdes i skikket stand og eventuelt byttes ut hvis det oppstar skade pa dem, slik at kunden uten vanskelighet kan lese dem.

Hvis det er en feil eller et problem med maskinen, ma den straks settes ut av funksjon. Og ma under ingen omstendigheter startes for problemet er rettet pa.

Installasjon, service, justering eller rutine vedlikehold skal bare utfores av kvalifiserte personer

For fortsatt beskyttelse mot brann, forsikre deg at hoved sikringen bare byttes ut med en av samme type og verdi. Bruk av andre sikringer eller materiale er forbudt.

Stromforsyningen inne i monitoren vill vzere varm og ha omrader med hoy spenning selv om maskinen har blitt slatt av. og det er muligheter for skader og elektriske sjokk. Veer forsiktig sa du ikke berorer disse omradene. For a forhindre mulige elektriske sjokk grunnet funksjonsfeil, ma denne maskinen vzere ordentlig jordet. Hvis ledningen til hoved stromforsyningen skades ma den straks byttes ut.

Ikke sla pa maskinen for den er korrekt installert. OBBB BBB BB BBE

For du kopler maskinen til stromnettet, forsikre deg om at maskinen innstilt for den korrekte spenningen og de riktige sikringene benyttes.

Page 19

MERKNADER VED INSTALLASJON 2msoem ornare

Sla ALDRI pa maskinens stromforsyning for installasjonen er fullfort.

For & forhindre eventuelle elektriske sjokk, forsikre deg om at For & forhindre at kundene blir skadet av spillets bevegelige deler. [

maskinen er koplet til et stromnett med ordentlig jording. q

forsikre deg om at det er minst 500mm avstand mellom andre maskiner eller vegger. mo O PEP

For a forhindre skade pa maskinen p.g.a. feil bruk, sorg for at spenningen Se | wt til hoved stromforsyningen er 230Volt AC. =

Praying zone MERKNADER: Hvis plassen hvor spillet skal plasseres har polerte gulv anbefales det at du benytter gummi sko under niva justeringene, for a forhindre at maskinen kan flytte pa seg.

MERKNADER: For a f& adgang til stromforsyningen og CPU-kort, forsikre deg om at bakparten av hoved kabinettet er skilt fra vegger eller andre maskiner med minst 500mm.

XN

Spillet har montert hjul for A gjore det letter a flytte pa. Hver forsiktig nar det skal flyttes pa en hellende overflate.

Hoved enheten i spillet har tyngdepunktet i fronten, sd det er viktig at minst 2 personer blir brukt til 4 montere eller flytte denne enheten.

Monterings posisjonen til hoved enheten er veldig hoy, og det er viktig at denne hoyden nas sikkert, uten at man ma strekke seg. Benytt deg av hjelpemiddel. (f.eks sto, krakk, gardintrapp osv)

Den totale hoyden pa hoved enheten er 2080mm. vzer forsiktig med hoye hindringer som f.eks lysror.

Nar spillet skal flyttes, forsikre deg om at spillet er delt i 3 deler: Topp enhet, Front enhet, Hoved enhe PB BBP &-

FJERNE OG UTSKIFTE ENHETER OG DELER.

Installasjon, service, justering eller rutine vedlikehold skal bare utfores av kvalifiserte personer.

Ikke lag noen forandringer pa denne maskinen uten godkjenning. Dette kan medfore uforutsette farer

Bare deler spesifisert av Namco Europe Ltd. skal benyttes ved utskifting eller reparasjon av deler (dette gjelder ogsa skruer).

Forsikre deg om at strommen er slatt av for du pabegynner noe som helst vedlikeholdsarbeid (feilsoking, reparasjon osv.)

Hvis du utforer arbeid som ikke er beskrevet i denne manualen, ta kontakt med din distributor for instruksjon da ikke noe ansvar vill bli akseptert for skade pa maskin eller pa personer

Deler av stromforsyningen og monitoren er fortsatt varm eller beerer hoye spenninger selv etter strommen er slatt av og kan forsake skader eller elektriske sjokk. Forsikre deg om at du ikke berorer disse delene.

Forsikre deg om at maskinen er slatt av for du kopler sammen eller tar fra hverandre plugger eller koplinger. >eP BBP BP PBB

Nar du fjerner hoved koplingene fra maskinen, eller hoved pluggen fra stopselet, ta bestandig tak i LL pluggen og ikke ledningen.

Page 20

@D Niets uit deze publikatie mag worden gereproduceerd door enig mechanisch, fotografisch of electronisch proces, of in de vorm van een fonografische opname, noch mag het opgeslagen worden in een retrieval system, doorgezonden of anderszins gekopieerd voor publiek of privégebruik, zonder toestemming van Namco Europe Limited.

Ofschoon de informatie in deze handleiding in goed vertrouwen is gegeven en nauwkeurig was ten tijde van het drukken, houdt Namco zich het recht voor om veranderingen en aanpassingen te maken zonder bericht.

Deze machine is geproduceerd volgens Richtlijnen van de Europese Gemeenschap, en is getest en is in overeenstemming met de Richtliinen 89/336/EEC en 72/23/EEC door de toepassing van de standaards EN55014, EN55104 en EN603365-1 (zie voorin de handleiding) en draagt als zodanig het CE-merk. Enige veranderingen of aanpassingen aan deze machine dienen in overeenstemming te zijn met de Richtliinen van de Europese Gemeenschap. Enige ongeauthoriseerde veranderingen aan dit produkt kunnen in strijd zijn met deze Richtlijnen.

Onder sommige omstandigheden van extreme externe storingen, bijv. radiotransmissies, electrostatische ontladingen of pieken op het net, kan prestatieteruggang optreden. De machine zal echter normaal presteren zodra de storingsbron gestopt of verwijderd is.

Let op: - als de spelprocessor reset a.g.v. een onderbreking of vermindering van de netstroom, dan kunnen opgebouwde credits verloren gaan.

Dit spel is niet een machine zoals omschreven in de Machinery Directive 89/392/EEC.

Veiligheidsopmerkingen Om deze machine veilig te kunnen gebruiken, dient voor installatie, aanpassing of gebruik van deze machine, de Bedieningshandleiding zorgvuldig gelezen te worden. Telkens wanneer de eigenaar van deze machine de demontage, installatie, aanpassing of routine-ondethoud toevertrouwd aan een andere persoon, dient de eigenaar er voor te zorgen dat deze persoon de juiste voorzorgsmaatregelen en relevante gedeeltes uit de handleiding lest voordat hij begint. Om er voor te zorgen dat geen ongelukken gebeuren als de machine gebruikt wordt, dienen onderstaande veiligheidsaanwijzingen Zorgvuldig opgevolgd te worden. Deze handleiding maakt samen met de installatiehandleiding (waar van toepassing) een integral deel uit van de apparatuur en moet te allen tijde ter beschikking staan van exploitatie- en ondethoudspersoneel. Deze machine is alleen bedoeld voor gebruik binnenshuis en dient alleen gebruikt te worden voor bedoelde doeleinden. Namco Ltd. is niet verantwoordelijk voor ongelukken, letsel of schade die voortkomt uit ongeoorloofde veranderingen aan of onjuist gebruik van deze machine

Veiligheidsopmerkingen

De volgende veiligheidsopmerkingen worden overal in deze handleiding gebruikt. Maak uzelf vertrouwd met deze opmerkingen en hun betekenis voor installatie, het plegen van onderhoud of het aanbrengen van aanpassingen aan deze machine.

WAARSCHUWING A Waarschuwing geeft een gevaar aan dat zou kunnen resulteren in letsel of de dood. Ga niet verder dan een waarschuwingsopmerking totdat de aangegeven omstandigheden volledig begrepen zijn en hieraan voldaan is.

VOORZICHTIG (2) _Voorzichtig geeft een gevaar aan dat zou kunnen resulteren in schade aan de machine. Ga niet verder dan een voorzichtigheidsopmerking totdat de aangegeven omstandigheden volledig begrepen zijn en hieraan voldaan is

Algemene veiligheidsoverwegingen

> Stel deze machine alleen in gebruik nadat gecontroleerd is of de machine correct en overeenkomstig de handleiding is geinstalleerd.

> Gedeeltes van deze machine bewegen tijdens het spel, waardoor er plaatsen zijn waar de afstand tussen het stilstaande gedeelte en de bewegende sectie verandert. Er zijn waarschuwingsstickers om handen en voeten van bewegende delen af te houden; als de exploitant echter van mening is dat iemand in gevaar is, dan dient hij deze persoon dienovereenkomstig te waarschuwen.

De waarschuwingsstickers dienen altijd in goede staat te worden gehouden en vervangen indien versleten, zodat de klant ze goed kan lezen

Als zich een fout of probleem voordoet met de machine, dan dient de machine onmiddellijk stopgezet en het probleem verholpen te worden voordat de machine verder gebruikt wordt.

Installatie, service, aanpassingen of routine-onderhoud dient alleen uitgevoerd te worden door hierin bekwame personen

Om blijvende bescherming tegen brandgevaar te garanderen, dient ervoor gezorgd te worden dat de netzekeringen alleen vervangen worden door zekeringen van hetzelfde type en dezelfde sterkte. het gebruik van andere zekeringen of ander materiaal is verboden.

De voeding in de monitor blijft warm en er kunnen componenten electrisch geladen blijven ondanks dat de machine UlTgeschakeld is, waardoor er brandwonden of electrischee schokken kunnen worden opgelopen. Ben voorzichting en raak deze delen niet aan.

Om mogelijke electrische schokken a.g.v. storingen te voorkomen, MOET deze machine voorzien zijn van een goed vastzittende aardstekker.

Mocht het netsnoer op enig moment beschadigd worden, dan moet deze onmiddellijk vervangen worden.

Zet de machine niet AAN totdat deze correct is geinstalleerd

Voordat de machine op het lichtnet wordt aangesloten, dient gecontroleerd te worden of de machine op het correcte voltage staat afgesteld en of de correcte zekeringen zijn aangebracht. OPP PP BP BB BB

Page 21

> BBE

(6)

Ne OPMERKING: Als de machine op een gladde ondergrond wordt gebruikt, Opmerkingen aangaande Installatie »

Sluit de machine nooit aan op de stroomtoevoer totdat de installatie [aaaae ml is voltooid. ci

Om mogelijke electrische schokken te voorkomen, dient ervoor gezorgd te worden dat de machine middels een goed vastzittende aardstekker op het lichtnet is aangesloten.

Om ervoor te zorgen dat klanten niet gewond raken door de beweging van het spel, dient ervoor gezorgd te worden dat er minimaal 500mm ruimte is tussen andere machines of muren.

Om schade aan de machine door verkeerd gebruik te voorkomen, dient ervoor gezorgd te worden dat het voltage van het lichtnet 230volts AC bedraagt. Praying zone

is het raadzaam rubber matjes onder de stelpootjes te bevestigen om te voorkomen dat de machine over de vioer gaat glijden

OPMERKING: Om toegang te krijgen tot de voeding- en de CPUassemblies, dient ervoor gezorgd te worden dat de achterkant van het kabinet minimaal 500mm verwijderd is van de muur of andere machines.

PB BBP B Het spel is voorzien van wieltjes, waardoor het gemakkelijker is om te verplaatsen. Wees voorzichtig als de machine op een hellend viak gereden wordt.

Het zwaartepunt van de Header Assembly ligt aan diens voorkant, waardoor het belangrijk is dat minimaal 2 personen de Header Assembly aanbrengen of verwijderen.

De Header Assembly moet op een hoge positie geplaatst worden en het is dus belangrijk dat deze hoogte veilig kan worden bereikt zonder veel te strekken. (bijv. middels een trap of een kruk)

De hoogte van het hoofdgedeelte is 2080mm: kijk dus uit voor obstakels zoals lampen.

Als de machine verplaatst of gedragen wordt, dient ervoor gezorgd te worden dat deze in 3 delen wordt afgebroken: Header Assembly, Front Assembly, Ride Assembly

b>PBPBBe B&B

> & Verwijderen en vervangen van Assemblies en onderdelen

Installatie, service, aanpassingen of routine-onderhoud dient alleen uitgevoerd te worden door hierin bekwame personen

Maak geen veranderingen aan deze machine zonder goedkeuring vooraf. Dit kan onvoorzien gevaar opleveren.

Alleen onderdelen die door Namco Europe Ltd. zijn gespecificeerd dienen gebruikt te worden bij het vervangen of repareren van onderdelen (incl. schroeven).

Zorg ervoor dat de machine UlTgeschakeld is voordat er enig onderhoudswerk wordt verricht (troubleshooting, reparaties etc.)

Bij het verrichten van werkzaamheden die niet in deze handleiding staan beschreven, dient voor instructies altijd contact opgenomen te worden met de verdeler aangezien geen verantwoording wordt genomen voor schade of letsel.

Delen van de voeding en de monitor blijven warm of behouden hoogspanning zelfs nadat de machine UlTgeschakeld is en zouden verbrandingen of electrische schokken kunnen veroorzaken. Ben voorzichting en raak deze delen niet per ongeluk aan.

Zorg ervoor dat de machine is UlTgeschakeld voordat pluggen of connectors ingestoken of uitgetrokken worden.

Als het netsnoer uit de machine of uit het stopcontact verwijderd wordt, dient altijd de stekker vastgepakt te worden en niet het snoer. wy

Page 22

Nenhuma parte desta publicacdo podera ser reproduzida por processos mecanograficos, fotograficos, electronics ou ainda sob a forma de gravacdo sonora nem tao pouco podera ser gravada através de sistemas informaticos transmissiveis ou de outra forma copiados para uso publico ou privado sem autorizagao expressa da NAMCO EUROPA LIMITADA.

A informagao contida neste manual foi fornecida de boa fé, sendo rigorosa na altura da sua publicagao. A NAMCO EUROPA LIMITADA, reserva-se o direito de proceder a mudancas e alteragdes sem qualquer aviso prévio. Esta maquina foi fabricada de acordo com as Directivas Comunitarias Europeias e tem sido testada em conformidade com as seguintes Directivas: 89/336/EEC e 72/23/EEC através dos requetimentos normativos, EN55014, EN55104 e EN60335-1 (ver capa frontal do manual) e como tal sustenta 0 certificado de marca de CE. Quaisqueres alteragdes ou modificagdes efectuadas nesta maquina deverao ser em conformidade com as Directivas da Comunidade Europeia. Quaisquer alteragdes nao autorizadas a este equipamento poderao infrigir tais Directivas.

O funcionamento normal desta maquina, podera ser afectado debaixo de algumas condicées extremas de interferéncias externas tais como; transmissdes via radio, descargas electroestaticas e passagens de corrente na rede de alimentacao. Contudo o seu funcionamento normal sera restabelecido logo que a fonte de interferéncias tenha cessado ou tenha sido neutralizada.

Nota :- Se o processador de jogo for inicializado devido a uma interrup¢ao ou quebra da corrente principal, quaisqueres creditos obtidos poderao desaparecer.

Este jogo por si sé nao contitui uma maquina tal como defenido pelas Directivas de Maquinaria de 89/392/EEC8.

AVISOS DE SEGURANCGA Afim de usar esta maquina com seguranga, certifique-se que Ié este manual de operador atentamente antes de proceder 4 montagem e afinacao ou uso da mesma. Sempre que o proprietario desta maquina confiar a desmontagem, instalago, afinagao ou manutengdo preventiva da mesma a outra pessoa, deverd este assegurar - se que a pessoa em questdo Ié as precaugées apropriadas e capitulos relevantes deste manual antes de iniciar o trabalho. Afim de evitar qualquer tipo de acidente quando a maquina estiver em funcionamento, devera seguir rigorosamente os procedimentos de seguranga descritos abaixo. Este manual juntamente com o manual de instalagao (aonde aplicavel), contituem parte integrante do equipamento e deverao estar sempre disponiveis ao operador e pessoal tecnico de assisténcia. Esta maquina destina-se a ser operada em espagos interiores apenas e a sua utilizagdo deve circunscrever-se somente aos fins previstos. A Namco Ltd. declina qualquer responsabilidade por acidentes, ferimentos ou danos resultantes de modificagées nao autorizadas ou uso indevido desta maquina.

AVISOS DE SEGURANCA

Os seguintes avisos de seguranga sao usados através de todo o manual. Familarize-se com cada um destes avisos e respectivos significados antes de instalar, assistir ou efectuar qualquer afinagdo nesta maquina.

PERIGO —/\_ Perigo revela uma situacao anormal que podera resultar em ferimentos ou morte. Ndo avance para além de um aviso de Perigo sem que todas as condigées indicadas estejam completamente esclarecidas e resolvidas.

CAUTELA 1) Cautela revela uma situagdo anormal que podera resultar em danos materiais para a maquina. Nao avance para além de um aviso de Cautela sem que todas as condigées indicadas estejam completamente esclarecidas e resolvidas.

AVISOS DE PERIGO

A\ Esta maquina so devera ser colocada em funcionamento apés ter sido verificado que se encontra instalada correctamente e de acordo com o manual de instrugdes

> Algumas partes componentes desta maquina movem-se durante a acco de jogo, porconseguinte existem lugares aonde a distancia entre a seccdo fixa e movel altera-se. Existem avisos para manter as maos e os pés afastados da zona de perigo movel, contudo caso o operador se aperceba de alguma pessoa em perigo, devera avisar amesma em conformidade.

Os avisos de perigo devem ser sempre mantidos em boas condigdes de leitura de forma a permitir uma leitura clara por parte do utilizador, caso se encontrem danificados deverao ser substituidos. Caso esta maquina manifeste algum erro ou problema durante o seu funcionamento, devera ser imediatamente parada até que o problema em questao seja rectificado

A montagem, assisténcia e afinagdes ou manutengao de rotina desta maquina, deverdo ser somente executadas por tecnicos ou pessoas devidamente qualificadas para o efeito.

Afim de garantir uma protegdo anti - fogo permanente nesta maquina, certifique-se que os fusiveis de protegao s4o sempre substituidos por fusiveis de igual valor ou calibre aos de origem. O uso de outro tipo de fusiveis ou material é proibido.

A fonte de alimentacao do monitor encontrar-se-a quente, tendo zonas de alta voltagem, mesmo apds a maquina ter sido desligada. Deste facto poder resultar a ocurréncia de queimaduras ou choques electricos. Seja cuidadoso para evitar contacto com estas zonas.

Esta maquina deve estar sempre equipada com uma ficha com circuito de protecgao a Terra, afim de evitar possiveis choques electricos, caso surga uma falha no sistema.

Se a qualquer altura o cabo de alimentagao principal ficar danificado, devera ser imediatamente substituido.

Nao ligar a maquina sem que esta tenha sido correctamente instalada.

Antes de ligar a maquina a tomada da rede de alimentagao principal, certifique-se de que a maquina esta preparada para a voltagem correspondente e de que também se encontra protegida com os fusiveis apropriados. OPP BP B BBP BE

Page 23

© PP BB)

NOTAS :

NOTAS :

NOTAS SOBRE A INSTALACAO

NUNCA ligar a maquina sem que a instalacdo esteja completamente 2msoenornore finalizada. [oman

Afim de evitar possiveis choques electricos, certifique-se que a maquina esta ligada a rede de alimentacao com uma ficha protegida com circuito de terra.

Afim de evitar ferimentos pessoais nos clientes, provocados pelo movimento da maquina, certifique-se que existe pelo menos 500mm de separagdo entre outras maquinas ou paredes.

Afim de evitar danos na maquina causados por falhas de operagao, certifique-se que a voltagem da rede de alimentagao principal é de 230volt AC.

Praying zone Se esta maquina estiver colocada sobre um chao polido, recomenda-se

a utilizagdo de tapetes de borracha debaixo dos pés niveladores, afim

de prevenir a maquina de deslizar no chao.

Quando precisar de aceder a fonte de alimentagao e s placas (CPU), certifique-se que a parte trazeira do movel central esta separada da parede ou de outras maquinas pelo menos 500mm afim de ganhar espago de manobra.

>PBPBPBP B Esta maquina esta equipada com rodas afim de facilitar a sua deslocacao tenha cuidado ao mover a maquina num plano inclinado.

O bloco Superior (Cabega) tem o centro de gravidade para a frente, porconseguinte é importante que pelo menos sejam utilizadas duas pessoas para montar ou desmontar este Bloco Superior.

A posigao do bloco superior quando montado na maquina 6 muito alta. Torna-se importante ter meios seguros de alcance, tais como; escadotes ou escadas afim de evitar riscos desnecessarios.

A altura total do bloco principal, é de 2080mm, tenha cuidado com qualquer tipo de obstrugées existentes em altura como por exemplo; calhas electricas ou candeiros.

Ao deslocar ou transportar a maquina, certifique-se que se encontra desmontada em 3 blocos: Bloco Superior, Bloco Frontal, Bloco da Cabine de Condugao ~\

bP B BBB BBE

SUBSTITUICAO E MONTAGEM DE PEGAS

A montagem, assisténcia e afinagdes ou manutengao de rotina desta maquina, devero ser somente executadas por tecnicos ou pessoas devidamente qualificadas para o efeito.

Nao faca qualquer tipo de alteracdo prévia nesta maquina sem aprovagao prévia. Se tal acontecer poderé provocar danos e perigos imprevisiveis.

A substituigdo ou reparacao de pegas devera ser feita apenas com pegas de origem ou especificadas pela “Namco Europa Ltd.” (incluindo parafusos)

Certifique-se que a maquina se encontra desligada sempre que iniciar qualquer tipo de trabalho de manutengao. (identifacao de avarias, reparagao etc.)

Caso esteja a efectuar um trabalho nao descrito neste manual, certifique-se que contacta o seu distribuidor para obter instrugdes, caso contrario nao serao aceites responsabilidades por danos causados ou ferimentos.

Algumas zonas da fonte de alimentagao e do monitor ficam quentes e transportam correntes de alta voltagem, mesmo depois de a maquina ter sido desligada, podendo causar queimaduras e choques electricos. Tome cuidado para nao tocar acidentalmente estas zonas.

Certifique-se que a maquina esta desligada antes de ligar ou desligar qualquer tipo de fichas ou jungées.

Quando desligar a ficha principal da maquina ou a ficha do cabo de alimentagao das tomadas da parede, devera sempre agarrar na ficha e nunca puxar pelo cabo da mesma.

Page 24

‘S

Ingen del av denna publikation far reproduceras, varken fotografiskt, elektroniskt eller i nagon form av ljudinspelning. Det far inte heller lagras i nagot atervinningssystem, dversandas eller pa annat satt kopieras fér offentlig eller privat anvandning, utan tillstand fran NAMCO EUROPE LIMITED.

Eftersom informationen i denna manual lamnas ut i god tro och var korrekt nar den trycktes, reserverar sig NAMCO EUROPE LIMITED f6r andringar.

Denna maskin har tillverkats enligt direktiv fran europeiska unionen, ar testad och uppfyller direktiven enligt 89/336EEC och 72/23/EEC med tillampning av EN55014, EN55104 och EN60335-1 standard (se manualens framsida) och bar darmed ocksa CE-market. Varje férandring eller modifiering av denna maskin maste ske i éverens-stammelse med EU-direktiven. En férandring i denna produkt, som inte ar auktoriserad, kan strida mot dessa direktiv.

Under vissa omsténdigheter nar det gller extrema externa stdrmingar, t ex radiosndningar, elektrostatiska urladdningar eller natburna strémstérningar, kan resultera i en nagot nedsatt funktion. Maskinen kommer dock att aterga till normal funktion, s& shart stérningen har upphért eller aviagsnats

OBS! Om spelprocessorn startar om till {Sljd av ett avbrott eller reducering av strémmen kan registrerade krediter ga forlorade.

Detta spel ar inte en maskin enligt definitionen i Maskindirektivet 89/392/EEC

SAKERHETS VARNING

For att maskinen ska kunna anvandas pa ett sakert satt, ska manualen lésas noggrant fére installation, anvéindning eller justering.

Om Agaren till maskinen anfértror nagon annan person att montera isar, installera, justera maskinen eller utféra rutinunderhall, ska dgaren férsakra sig om att denna person laser om férsiktighetsatgarder och tillampliga delar av denna manual innan arbetet pabérjas.

For att fSrhindra att nagon olycka hander nar maskinen r igang, maste sdikerhetspunkterna beskrivna nedan féljas strikt.

Denna manual tillsammans med installationsmanualen (nr tillampligt) utg6r en integrerad del av utrustningen och maste vara standigt tillganglig fér operatérer och service personal.

Maskinen ar avsedd for inomhusbruk och ska endast anvandas fér detta andamal.

Namco Ltd. bar inget ansvar anvandande av densamma. 6r olyckor eller skador som orsakats av icke auktoriserade andringar i maskinen eller felaktigt

SAKERHETSANVISNINGAR

Sakethetsanvisningarna nedan anvands genomgaende i manualen. Gr dig fértrogen med varje anvisning och dess innebérd innan installation, service eller justeringar gérs pa denna maskin.

VARNING A ”Varning” anger en fara som skulle kunna skada eller fororsaka dédsfall. Fortsatt inte vid en sadan varningsanvising innan de pavisade férhallandena ar forstadda och atgardade i sin helhet.

OBSERVERA () "OBSERVERA" anger en fara som skulle kunna férorsaka skada pa maskinen. Fortsaitt inte vid en sAdan varningsanvising innan de pavisade férhallandena ar férstadda och Atgardade i sin helhet.

ALLMANNA SAKERHETSBEAKTANDEN

Satt inte igang maskinen utan att ha kontrollerat att den ar korrekt installerad och i 6verensstammelse med manualen.

Eftersom delar av maskinen rér sig under spel finns det stallen dar avstandet mellan den stationara delen och den rérliga Andras. Det finns varningsanvisningar om att halla hander och fétter borta fran rérliga delar, men skulle operatéren anse att en person ar | nagon som helst fara, ska personen ifraga varnas.

Varningsanvisningarna maste alltid hallas i gott skick och ersattas nar de blir slitna, sa att kunderna kan lasa dem dem tydligt.

Om det uppstar fel eller problem med maskinen, maste anvandningen stoppas omedelbart och problemet rattas till innan den ater anvands.

Installation, service, justeringar eller rutinunderhall ska endast utféras av en fér andamalet kvalificerad person.

For kontinuerligt skydd mot brandfara, ska man férsakra sig om att huvudsakringarna endast ersatts med samma typ och specifikationer. Anvandandet av andra sakringar eller material ar férbjuden. Strémférsérjningen inne i monitorn haller sig varm och har omraden med hég spanning, ven nar maskinen stangts av och det finns risk for brannskada eller elektriska stdtar. Var forsiktig och vidror aldrig sadana omraden.

For att forhindra en eventuell elektrisk stét fororsakad av fel, MASTE maskinen vara forsedd med sakert ansluten JORDAD kontakt.

Om strémférsérjningskabein pa nagot satt skadas, mAste den bytas ut omedelbart.

Vrid inte stro6mbrytaren till ON innan maskinen ar korrekt installerad. OPP BP BBB BBP BP B&B

Innan strémmen sats pa till maskinen, maste man férsdkra sig om att den Ar installd pa ratt spanning och att ratt sAkringar ar isatta.

Page 25

A A

A

©

OBSERVERA: Om maskinen ar placerad pa ett polerat golv, rekommenderas

OBSERVERA: For att kunna komma at stromf6rsdrjningen och CPU, se till att ATT BEAKTA VID INSTALLATION 2ms0enormore

Satt aldrig pa strommen pa maskinen innan installationen ar klar.

For att forhindra elektt kopplas till stromfors a chocker, férsakra dig om att maskinen ing med jordad kontakt | en le For att undvika skador av spelets rérelser, forsakra dig om att det finns ett avstand pa minst 500 mm till annan maskin eller vagg i

For att undvika skador pa maskinen p g a felaktigt handhavande, férsakra dig om att strémstyrkan ar 230 volt AC.

att placera gummibrickor under nivajusteringen for att forhindra att maskinen glider pa golvet. cai

baksidan av huvudkabinettet ar placerat minst 500 mm fran vagg eller annan maskin.

PB BBE B& Spelet ar férsett med hjul fr att underlatta férflyttningar. Var frsiktig om spelet ska flyttas pa en sluttande yta.

Toppskylten har tyngdpunkten framtill, darfér ar det viktigt att minst 2 personer satter dit eller tar bort den.

Toppskyltens placering ar mycket hégt upp och det ar viktigt att sadana hjalpmedel anvands s att man nar upp utan att strécka sig (t ex trappstege, pall osv).

Den totala héjden ar 2080 mm, tank pa eventuella hégt placerade hinder, t ex lampor.

Om spelet ska flyttas eller baras, kontrollera att spelet ar monterat isar i 3 delar: Toppskylt, Monitorenhet, Spelkontrollenhet

> FP BP BB

> ATT TA BORT ELLER BYTA UT ENHETER OCH DELAR >)

Justeringar och underhall pa denna maskin skall endast utféras av kvalificerad personal.

Gér inga andringar pa denna maskin utan ett godkannande i férvag. Detta kan férorsaka oférutsagbar fara.

Endast delar som 4r specificerade av Namco Europe Ltd. ska anvandas vid utbyten eller reparation av delar (inklusive skruvar).

Férsakra dig om att stroémmen 4r avstangd innan underhallsarbete pabérjas (felsékning, reparationer etc.)

Om arbete ska utféras som inte ar beskrivet i denna manual, ar det viktigt att kontakta aterférsaljaren fér instruktioner eftersom inget ansvar accepteras fér averkan eller personskador.

Delar av stromférsérjningen och monitorn ar varma och strémbarande aven efter stré6mmen stangts av och kan orsaka brannskador eller elektriska stotar.

Foérsakra dig om att maskinen ar avstangd innan kontakter satts i eller tas ur.

Nar kontakten tas ur maskinen eller ur vaggen, ta alltid tag i kontakten och inte i sladden. w

Page 26

<>)

Tasta julkaisusta ei saa ottaa misséan muodossa kopioita yksityis- tai julkiseen kaytt66n ilman NAMCO EUROPE LIMITED:in lupaa.

Tass ohjekirjassa olevat tiedot pitavat julkaisuhetkella paikkansa. NAMCO EUROPE LIMITED.:illa on kuitenkin oikeus muutoksiin ilman erillista ilmoitusta.

Tama laite on valmistettu EC direktiivien mukaisesti. Se on testattu ja todettu noudattavan seuraavia direktliveja: 89/336/EEC ja 72/23/EEC (EN55014, EN55104 ja EN 6035-1 standardit). Nain ollen tama laite on varustettu CE-merkinnailla. Kaikki tahan laitteeseen kohdistetut muutokset on tehtva EC- direktiivien mukaisesti. Mika tahansa valtuuttamattoman huoltomiehen tekema muutos voi olla direktiivien vastainen.

Laitteen toiminta voi hairiintya maaratyissa olosuhteissa, jotka johtuvat 4arimmaisista ulkoisista sahkOhairidista, kuten radiolahetys, elektrostaattinen purkaus tai vahvavirrasta syntynyt hairid. Toiminta normalisoituu kuitenkin heti, kun ulkoinen sAhkéhairié on poistettu.

Huom:- Jos peliprosessori resetoituu sahkékatkoksen tai vastaavan johdosta, voivat kaikki pelivaraukset havita.

Tama laite ei ole 89/392/EEC direktiivien mukainen kone.

Turvallisuusvaroitus

Taman laitteen turvallinen kayttd edellyttéa kayttéohjekirjan huolellista lukemista ennen laitteen asennusta, sdatda tai kayttOa.

Jos taman laitteen omistaja antaa jollekin toiselle osapuolelle tehtavaksi purkaa, asentaa, sata tai muuten huoltaa laitetta, on omistajan varmistuttava siita, ett toinen osapuoli on lukenut ja ymmértanyt kAyttéohjekirjan oleelliset osat ennen tyéhén ryhtymista.

Turvallisuusohjeita on seurattava tarkoin vahinkojen valttamiseksi laitteen ollessa kaytéssa .

Tama ohje sek mahdollinen asennusohje muodostavat laitteiston oleellisen osan ja on siksi aina oltava huolto- ja kayttéhenkildkunnan kaytettavissa.

Tama laite on tarkoitettu vain sisatilakaytté6n. Sita ei saa kayttaa muihin tarkoituksiin.

Namco Ltd ei vastaa niista onnettomuuksista, loukaantumisista tai vahingoista, jotka johtuvat laitteeseen ilman Namco Ltd:n lupaa tehdyista muutoksista laitteen vaarasta kaytésta.

Turvallisuusohjeet

Tass kayttéohjekirjassa on kaytetty seuraavia turvallisuuteen liittyvié huomautuksia. Tutustu jokaiseen ndista. Ala asenna, huolla tai s4&da laitteistoa, ennen kuin olet taysin ymmartanyt mit& ne tarkoittavat.

VAARA “Vara” tarkoittaa uhkaa, joka voi johtaa loukkantumiseen tai kuolemaan, Ala koskaan ohita Vaara-merkintaa, ennenkuin ohjeissa esitetyt olosuhteet on ymméarretty taysin

VAROITUS, © “Varoitus” tarkoittaa uhkaa, joka voi johtaa laitteen vioittumiseen. Ala koskaan ohita Vaara-merkintaa,

YLEISET TURVALLISUUSNAKOKOHDAT

Varmista, etd laite on asennettu oikein ja ohjekirjan mukaisesti ennen kayttddnottoa. be Laite sisaltaa toimiessaan liikkuvia osia. On paikkoja, jossa liikkuvien osien ja paikalla pysyvien osien valimatka muuttuu. Tallaisissa paikoissa on varoitustaulut, joissa kehotetaan pitamaan kasia ja jalkoja poissa liikkuvista osista. Jos kayttaja on sit mieltd, etta joku henkild on vaarassa, on kayttajan velvollisuus varoittaa vaarassa olijaa.

Varoitustaulut on pidettava hyvassa kunnossa. Jos ne ovat kuluneet, ne on ehdottomasti vaihdettava, jotta asiakkaalla olisi mahdollisuus lukea niita selvasti.

Jos laitteeseen tulee vika tai ongelmia, on se pysaytettéva valittémasti ja ongelma selvitettava ennen uutta kayttddnottoa.

Vain riittavan ammattipatevyyden omaava henkild saa suorittaa asennus-, huolto-, saaté- tai muita laitteeseen kohdistuvia rutiinitoimenpiteita.

Jotta palovaaraa ei syntyisi, saa padsulakkeita vaihtaa vain samankokoisiin sulakkeisiin. Muiden sulakkeiden tai materiaalin kaytté on ehdottomasti kielletty. Monitorin sisalla oleva virtalahde pysyy kuumana ja siina on alueita, joissa on korkeajannite vaikka laite on kytketty pois paalta. Palovammojen tai sahkdiskun saaminen on mahdollista. Ald koske naihin alueisiin. Sahkdiskujen valttamiseksi vikatapauksissa, laite on ehdottomasti kytkettava maadoitetulla johdolla maadoitettuun pistorasiaan.

Vioittunut verkkojohto on valittémasti vaihdettava.

Ala kytke laitetta paalle, ennen kuin se on oikein asennettu. OPP PBBBBP BE

Varmista ennen verkkoon kytkemista, ett virtalahteen jannitteen asetus on asetettu oikealle jAnnitteelle ja ett siind on oikeat sulakkeet.

Page 27

> Ee Be

(3)

Huomio: Jos tama laite sijoitetaan liukkaalle esim. vahatulle lattialle, ASENNUSHUOMIOITA

Ala koskaan kytke laitetta paalle ennen kuin asennus on a suoritettu loppuun

Taman laitteen virtalahde on kytkettava maadoitetulla johdolla

maadoitettuun pistorasiaan, jotta sahkéiskun vaaraa éi olisi.

Varmista, etd laitteen ja seinan tai toisen laitteen valissa on vahintéan 500 mm, jotta asiakkaat eivat loukkaannu laitteen likkumisesta johtuen. Varmista, etta virtalahteen jannite on 230 V AC, jotta ei laite 1 wf fan a vioitu.

Paying zone

suositellaan laitettavaksi kumityynyt sdatdjalkoihin liikkumisen estamiseksi.

Huomio: Varmista, etté takaosan taakse jaa vahintaan 500 mm tilaa, jotta virtalahteeseen ja CPU-korttiin paasee kasiksi.

PRP BP Be &- ~ Laite on varustettu kaantyvilla pydrilla. Tama on pidettava mielessa, kun laitetta siirretaan kaltevalla alustalla.

Yldosan painopiste on ylaosan etuosassa. Tasta syysta on yldosaa asennettaessa tai poistettaessa oltava vahintaan kaksi henkilda.

Yldosan asennusasento on erittain korkealla. On tarkeaa, ettd tarvittavalle korkeudelle paastaan vaivattomasti ilman venyttamista. (esim. kayta tukevia tuoleja tai tikkaita)

Laitteen kokonaiskorkeus on yli 2080 mm. Varmista, ettei katossa ole esteita. esim. valaisimia.

Kun siirrat tai kannat laitetta varmista, etta laite on purettu neljéan osaan. Yldosa, koottu, Etuosa, koottu, Liikkuva ajo-osa, koottu a

PRP BP BBP BP B B& ~\ Vain riittavan ammattipatevyyden omaava henkildé saa suorittaa asennus-, huolto-, saaté- tai muita laitteeseen kohdistuvia rutiinitoimenpiteita.

Talle laitteelle ei saa tehda mitéan hyvaksymattomia muutoksia. Se voi aiheuttaa ennalta-arvaamattomia vaaroja.

Vain Namco Europe Ltd:n maarittelemia varaosia saa kayttaa vaihtaessasi tai korjatessasi osia. (sisaltaen ruuvit).

Varmista, etta laite on kytketty POIS PAALTA ennen tyén aloittamista.

Ota yhteytta maahantuojaan ohjeita varten, jos joudut tekemaan tydtehtavi huoltokirjassa, muuten vastuuta vioista tai loukkaantumisista ei ole. joita ei ole esitelty

Virtalahde ja monitori pysyvat kuumina ja niissa on alueita, joissa on korkeajannite vaikka laite on kytketty pois paalta. Palovammojen tai sahkdiskun saaminen on mahdollista. Ala koske ndihin laitteisiin.

Varmista, ett laite on kytketty POIS PAALTA ennen johtojen kytkemista tai irrottamista.

Irrottaessasi verkkojohdon seinasta tai laitteesta, ota kiinni itse pistokkeesta, ei johdosta.

Page 28

FoON>

9.

  • SCHEMATIC Contents

SPECIFICATIONS HOW TO PLAY MAJOR COMPONENTS. MOVING THE MACHINE 4-1 Removing the Header Assy and Side Poles. INSTALLATION .. 5-1 Fitting the Front assy to the Monitor assy . 5-2. Linking two Machines ADJUSTMENTS

6-1 Turning on the Power. 6-2 — Adjustment Switches ...........cccccscsccssesseseseeceeeessesssssseseescssesseseseseeesssssessesesancasesesseseentees 14 6-3 Test Mode 6-3-1 Coin Options 6-3-2 Game Options ... BBB WO 'TeSt verscsssarcrsassrersesrceserensagesaesesuncrsasaanangunsegressnescsrnnsanen negtensnansudaranenegenaesuregbarssa 6-3-3-1 I/O PCB Check 6-3-3-2 How to [I/F Initialize] 6-3-3-3 Gun Tet vic ccossscssssnsassncasiaves covecsianavanasuaisnssaveasccevasnsaianintesineiecdend civvastssaceteaes 6-3-3-4 Gun Initialize .

6-3-3-5 Switch Test.... 6-3-3-6 Camora Cheek i sisisccssscsssisnsinvsarisanieonitesossaveacucesavstariniininnniigia ieee cvensctastanss 23 6-3-4 Monitor Test... 6-3-5 Sound Test .

6-3-6 ADS Data.... : 6-3-7 OMNES oases eeeececeseeeescsssesesesseeceesescseseeeescssssscsesvssescasassesueeeesesessceeseseessasesssseseeesasecsce® 27 INITIALIZATION . MAINTENANCE...

8-1 Greasing the Gun Assembly 8-2 Replacing the Fluorescent Lamp or Starte: 8-3. Replacing the Gun Assembly... 8-4 Replacing the Gun Solenoid 8-5 Replacing the Blue LED Assembly . 8-6 Replacing the Trigger Microswitch .. 8-7 Replacing the Backward / Forward Potentiometer . : 8-8 Replacing the Left / Right Slide Potentiometer ..0...... eee cee 42 8-9 Replacing the Left / Right Potentiometer 8-10 Replacing the Monitor 8-11 Replacing the Camera ..........ccccsccscsseseeeeesesseseseseseseencasesssseseeeeeessessseseenesensesessesesseneetens 48 PARTS

Page 29
  • SPECIFICATIONS

POWER SUPPLY:- 230v/320watts AC

AMBIENT OPERATING ° ° + + TEMPERATURE: BIC to +26°C

MONITOR:- Hantarex 28” Polo - Medium Planar (Type 02193240)

COIN ACCEPTOR:- Mars CashFlow - 4 Channel Dispense

DIMENSIONS:- Assembled 1470(w) x 1364(d) x 2080(h)

Monitor Cabinet 1470(w) x 680(d) x 1855(h) Front Assembly 1230(w) x 694(d) x 2080(h)

WEIGHT:- Assembled 330kg

Monitor Cabinet 210kg Front Assembly 120kg

ACCESSORIES:- Keys: (Cash Door) (Coin Door) (Back Door).

IEC Mains Lead ........ ccc 1

Operators Manual...

Monitor Manual.............c:ccscceseeeeee 1

CashFlow Documents.............05 1

Link Cable 2.9mtr 0... 1

Potentiometer «0... 1

M5 Security Wrench... 1

Hex Head Set Screw (M10x70) . Spring Washer (M10) Flat Washer (M10x25x2.3) .

Nylon C/Sunk Screw. Gun Grip DecalL &R

Page 30
  • HOWTO PLAY

This is a combat game for one to four (2 games linked) players competing against each, and/or the computer, for diamond awards. The game takes a picture of each player and captures it to the screen (“Face Capturing” system). where it identifies the player during the game. No additional players are allowed to join the game once the game has started.

Game Rules Players belong to either of two teams to compete against each other or to compete together against the other team. Each team consists of 4 robots which can be game players, computer robots or a mix of game players and computer robots. The player selects which team to be part of (“Flexible Participation” system) before the start of the game. All robots are equal in performance. Destruction of an enemy robot makes available diamond awards which a player can aquire.

CPU Robots Regardless of the number of players there is always eight player or CPU controlled robots. In single play mode, three robots of your team mates and four enemy robots are controlled by the CPU.

Resurrection Robots knocked out can resurrect endlessly within the given time period. After resurrection the player rejoins the combat at either the extreme left or right end of the battlefield.

Control One player controls one robot. The gun movement is used to control the Robot. The only weapon available is a machine gun. All guns are identical. Two viewpoints are given as follows: @ Water Park and Shopping District stages. The players robot is shown from behind from the waist up. ™ Subway stage. The players robot is shown from behind from the shoulders up.

Battle Field Combat occurs in an area typical of a Japanese urban area of today. Players select one of three zones: @ Water Park: Simple shaped battlefied with relatively open perspective and good visibility.

™ = Shopping District: Relatively wide battle field where objects are arranged

to give a medium difficulty level. m@ Subway: Relatively complicated battlefield within a small area.

Winning and Ranking The game is over at the end of a preset time period. The team with the most diamond awards is the winner. Individual player’s scores are displayed, as well as team results, at the end of the game.

Page 31
  • MAJOR COMPONENTS

Monitor assembly

CPU assembly

Front assembly Fluorescent lamp

Mensa Mains On/Off

Camera assembly

—— Side pole

Monitor

| Gun base assembly

Coin assembly CPU assembly

Page 32

fa MOVING THE MACHINE

a ~

This machine is fitted with castors to make it easier to move. Take care when

moving the machine on an inclined surface.

The overall height of the machine is 2080mm. Take care of any overhead

obstructions. (e.g. Light Fittings, Electric Cables etc.)

When moving the game, ensure that the game is dis-assembled into 2 parts: Monitor Assembly and Front Assembly.

The Front Assy is unstable when seperated from the Monitor Assy. Take care that theFront assy does not over balance backwards or forwards when moving.

Note: The Front assembly can be further dismantled by removing the Header assembly and Side poles. (see 4-1 below) )

4-1 Removing the Header Assy and Side Poles

The header assembly is heavy, approx 20kg. ensure that at least 2 people are available to remove the header assy and that there is sufficient space to work.

  • Remove the 6off security screws (M5x16) and remove the frame cover.

Security screw (M5 x 16)

Frame cover

Security screw (M5 x 16)

Page 33
  • Disconnect the connector.

Connector

  • Ensure that the header assy is being held firmly to prevent it falling and remove the 4off hex head set screws (M8x20), and remove the header assembly.

Hex head screw (M8x20)

Connector

Header assy

Page 34
  • Disconnect the connector inside the Gun Base assembly.

Gun base assembly

Connector

  • Remove 4off hex head screws (M8x45) and remove the Side Pole.
Note: The side pole is 1.92m high and approx 10kg. Ensure that at least two people are available to remove the side pole, and that there is adequate workspace.

Hex head screw (M8 x 45)

Side pole

Hext head screw (M8 x 45)

  • Repeat to remove the other Side Pole.
  • Reassemble in reverse order.
Page 35

5. INSTALLATION

Notes on Installation

WARNING
WARNING
WARNING
CAUTION NEVER turn the power to the machine ON until installation has been completed.

In order to prevent possible electric shocks, be sure that the machine is connected to the mains with a securely connected earthed plug.

So that customers are not injured , ensure that there is at least 500mm separation between other machines or walls.

In order to avoid damage to the machine due to misoperation, ensure that the voltage of the mains supply is 230volts AC.

NOTE

If the location site of this machine has a polished floor it is

recommended that rubber pads are fitted under the level adjusters to prevent the machine sliding on the floor.

In order to gain access to the Power Supply and CPU assemblies, make sure that the rear of the machine is separated from a wall or other machine by at least 500mm.

When installation is complete, it is imperative that the game is initialized. (See section 7 page 56)

Page 36

=

aa

=

ape

=

PO

= A

This machine is designed for INDOOR USE ONLY. Do not install in the following places.

Outdoors Direct Sunlight, places with excessive humidity or dust, places where there is water leakage, near air-conditioning or heating equipment, places with excessive heat or cold temperature. Places where it would be in the way of emergency exits or fire extinguishing equipment. Unstable places or places with excessive vibration. Places that are not level. This machine must not be cleaned with a water jet, or installed in an area where a water jet could be used.

DIESES GERAT IST NUR FUR DIE GEWERBLICHE AUFSTELLUNG IN GESCHLOSSENEN RAUMEN BESTIMMT. DAS GERAT DARF AN FOLGENDEN PLATZEN NICHT AUFGESTELLT WERDEN

Im Freien. In direktem Sonnenschein, an extrem feuchten und staubigen Platzen, an Platzen mit Wasseranschlissen und méglichen Leckagen, nahe Klima- und Heizungsanlagen, an Platzen mit extrem hohen oder niedrigen Temperaturen. In der Nahe von Notausgangen oder Feuerléschgeraten. An unstabilen Platzen oder Platzen mit ibermaRiger Vibration. An Platzen, die nicht eben sind.

DENNE MASKINE ER KUN DESIGNET TIL INDEND@RSBRUG

INSTALLER IKKE MASKINEN PA FOLGENDE STEDER

Udenders Direkte sollys, steder med hgj fugtighed el. stov, steder med vand udslip, i nerheden af air-condition eller varme udstyr, steder med usedvanlig hgj el. kold temperatur. Steder hvor den vil sta i vejen for nodudgange eller brandslukningsudstyr. Ustabile steder eller steder med for store vibrationer. Steder der ikke er plane.

ESTA MAQUINA ESTA DISENADA UNICAMENTE PARA USO EN INTERIORES. NO INSTALE LA MAQUINA EN LOS SIGUIENTES LUGARES.

Exteriores. Bajo luz solar directa, en lugares con polvo o humedad excesiva, lugares donde hay filtraciones de agua, cerca de aparatos de calefaccién o de aire acondicionado, lugares con temperatura ambiente muy alta o muy baja. Lugares donde la maquina obstruya salidas de emergencia o equipos de extincion de incendios. Suelos inestables o lugares con vibraciones excesivas. Lugares con suelos no nivelados.

Page 37

©

=

=

fae

Pe

Pe A

CETTE MACHINE EST DESTINEE UNIQUEMENT A UN USAGE INTERIEUR NE PAS INSTALLER LA MACHINE DANS LES ENDROITS SUIVANTS

A?extérieur. Directement exposée au soleil, aux endroits excessivement humides ou poussiéreux, aux endroits ou il y a des risques de fuite d’eau, prés de ventilateurs ou source de chaleur, aux endroits trés chauds ou froids. Dans des zones de proximité des sorties de secours ou d’accés aux équipements d’extinction du feu. Dans des emplacements instables ou soumis a de fortes vibrations. Dans des endroits dénivelés.

TO MHXANHMA EINAI ZXEAIAZMENO TIA XPHEH ZE EZQTEPIKO XQOPO MONO MHN TONOOETHZETE TO MHXANHMA £TOYE AKOAOYOOYE XOPOYE

E€wtepika Ameu@eiac oTov nAlo,oe WEpn ONou UNGPXE! Uypacia fh OKOvN,HEPN OTIOU UTIaPXE! APBovo vepo,kovTa ¢ air-condition fh GAAou Eidouc BEppavon,HEpH PE UTIEPBOAIKH UNA XapNAn SeppoKpaoia. Ze pep Orou epModiZouv péoa avayKnec 1.x. MUPOOREOTHpES fH GAAa. Mn ota8epa pEpn fh HEpH WE TOAAOUG KpadaocpoUs. Mépn nou dev eivai enineda.

QUESTA MACCHINA E’ PROGETTATA PER ESSERE USATA ESCLUSIVAMENTE IN AMBIENTI INTERNI. NON INSTALLARE LA MACCHINA NEI SEGUENTI LUOGHI.

In ambienti esterni. Alla luce diretta del sole, in posti con eccesiva umidita 0 polvere, in luoghi dove ci siano infiltrazioni d’acqua, vicino ad apparecchi di condizionamento d’aria oppure riscaldamento, in posti eccessivamente caldi 0 freddi. In luoghi dove potrebbe esserci un uscita di emergenza o un’attrezzatura per lo spegnimento del fuoco. In posti non stabili o con eccessive vibrazioni. In luoghi non piani.

DENNE MASKINEN ER BARE KONSTRUERT FOR INNENDORS BRUK IKKE INSTALLER MASKINEN PA F@LGENDE PLASSER.

Utenders Konstant sollys, plasser med mye fuktighet og stov, plasser hvor det er vannlekasje, nere luft kjolere eller varme elementer, plasser med overdreven hoy eller lav temperatur. Plasser hvor det vill sta i veien for nadutganger eller brannslukking utstyr. Ustabile plasser eller plasser med overdreven vibrasjon. Plasser som ikke er i vater.

DEZE MACHINE IS ALLEEN VOOR GEBRUIK BINNENSHUIS ONTWORPEN INSTALLEER DE MACHINE NIET OP DE VOLGENDE PLAATSEN

Buiten In direct zonlicht, op plaatsen met een zeer hoge vochtigheidsgraad of met veel stof, op plaatsen waar een waterlek is, dichtbij airco’s of verwarmingsapparatuur, op plaatsen met een zeer hoge of koude temperatuur. Op plaatsen waar nooduitgangen of blusapparatuur worden geblokkeerd. Op onstabiele plaatsen of plaatsen waar grote trillingen voorkomen. Op plaatsen die niet viak zijn.

Page 38

A

ESTA MAQUINA FOI CONCEBIDA PARA UTILIZAGAO EM ESPACOS

@) INTERIORES APENAS

NAO INSTALAR A MAQUINAS NOS SEGUINTES LOCAIS:-

  • Exteriores.
  • “Luz solar directa, locais com humidade excessiva ou po, locais aonde existam fugas de agua perto de ar condicionados ou equipamentos calorificos e locais com temperaturas excessivamente quentes ou frias.
  • Locais aonde ficaria colocada no caminho de saidas de emergéncia ou equipamentos extintores de fogo.
  • Locais estruturalmente instaveis ou locais com vibragées excessivas.
  • Locais nao nivelados.

DENNA MASKIN AR AVSEDD ENBART FOR INOMHUSBRUK

OS) INSTALLERA EJ MASKINEN PA FOLJANDE STALLEN

  • Utomhus
  • I direkt solsken, platser med extremt hég luftfuktighet eller damm, platser dar det forekommer vattenlackage, nara luftkonditionering eller varmeelement, i extremt hég eller lag temperatur.
  • Platser dar den skulle kunna vara i vagen fér nédutgangar och brandslackningsutrustning.
  • Instabila stallen eller dar stark vibration forekommer.
  • Platser med nivaskillnad.

TAMA LAITE ON SUUNNITELTU VAIN SISAKAYTTOON

GF) ALA ASENNA LAITETTA SEURAAVIIN PAIKKOIHIN:

  • Ulkotilaan
  • Suoraan aurinkovaloon, kosteisiin tai pélyisiin paikkoihin, vesivuotopaikkojen laheisyyteen, ilmanvaihto- tai lammityslaitteen lahistdlle tai paikkoihin, jossa on erittain kuumaa tai kylmaa.
  • Varauloskaytavien, muiden pakoteiden tai tulensammutusvidlineiden eteen.
  • Epavakaisiin tai tariseviin paikkoihin.
  • Kaltevalle alustalle.
Page 39

5-1 Fitting the Front assy to the Monitor assy

  • Place the Front assembly close to the Monitor assembly and connect the connectors.

Front Assy

Control Assy

Connector

  • Push the Front assembly up to the monitor assembly completely, taking care not to trap any wires.
  • Remove the rear door from the Monitor assembly.
  • Fit 60ff hex head screws (M10x50) to retain the Front assembly to the Monitor assembly.

Hex head screw (M10x50)

5. When the assembled game is in its final position, lower the eight (8) level

adjusters,(4off Monitor Assy and 4off Gun Assy), with a spanner so that the machine is level and all castors are raised from the floor by approx. 5mm. Tighten the lock nuts with a spanner to ensure that the level adjusters do not move.

Note: If the location site of this machine has a polished floor it is recommended that rubber pads are fitted under the level adjusters to prevent the machine sliding on the floor when in use.
Page 40

5-2. Linking two Machines

  • Switch both machines off.
  • Remove 2off pozi head screws (M5x12) and remove the Link Cover Bracket.
  • Fit the Link Cable (supplied) as shown in the following diagram

Rear of the assembly (2) Rear of the front assembly (1) P a >

8 6 a 6

== ==) or - or Oo | i)

  • Refit the Link Cover Bracket with the 2off pozi head screws (M5x12).

See section 6-3-2 page 42 to set the game PCB ID. Failure to set the 5. ID will prevent the games operating correctly.

Page 41
  • ADJUSTMENTS

® © 026 60 6 8 © @ A

Adjustment or maintenance on this machine should be carried out by qualified personnel only.

Einstellungen und Wartung des Gerates dirfen nur von dafir qualifiziertem Fachpersonal vorgenommen werden.

Justeringer eller vedligehold af denne maskine bor kun udfores af kvalificeret personale.

Los ajustes y el mantenimiento de esta maquina deben ser realizados s6lo por personal cualificado.

L’installation, le service, le reglage, ou la maintenance doivent étre effectués uniquement par les personnes qualifiées.

Metatponés f emldiopOwoeic oTa pnXavnpaTa MpémeE! va yivovtTal HOvo amo e€ouciodoTHpEVa ATouA.

Regolazioni e manutenzione su questa macchina devono essere fatti solo da personale specializzato.

Justering eller vedlikehold pa denne maskinen skall bare utfgres av kvalifiserte personell.

Aanpassingen of onderhoud aan deze machine dient alleen uitgevoerd te worden door bekwaam personeel.

Afinag6es ou manutengao nesta maquina, deverdo ser efectuadas somente por pessoal qualificado.

Justeringar och underhall pa denna maskin skall endast utféras av kvalificerad personal.

Tata laitetta saa saataa tai huoltaa vain siihen ammattipatevyyden omaava henkilékunta.

6-1 Turning on the Power

After the machine has been installed, turn ON the power. The power switch is located on the rear of the monitor cabinet.

Page 42

6-2 Adjustment Switches

The Adjustment switches are located inside the coin door.

1. Service Switch. Press this switch to obtain game credits without incrementing the play meter.

Test Switch Slide the test switch ON to enter test mode. Test mode allows testing and the changing of game settings. (Refer to section 6-3 "Test Mode" page 43)

Select Up/Down Switch This switch is used to select the test required when in the Test Mode.

Enter Switch This switch is used to enter a selected test and to change settings within a test.

COIN COUNTER z 2 Amp Q/B (Coin Fuse) : oe)

PLAYER 1 PLAYER 2

up up ®} SELECT SELECT|® DOWN DOWN

O ENTER O ENTER

TEST SERVICE TEST SERVICE

Page 43

6-3 Test Mode

  • Open the coin door and slide the test switch “ON”. The “Menu Screen’ will be displayed on the monitor.
  • Select the test required by using the select up/down switch. The colour of the selected test will change.
  • Activate the test by pressing the Enter switch. Select “EXIT” in each test to return to the “Menu Screen”.
  • After testing is completed, slide the test switch to the “OFF” position to return to normal game mode.

The Test Switch must always be in the “OFF” position for normal game mode.

>) MENU

COIN OPTIONS 2.0. cerns ...Used to set the price of play.

GAME OPTIONS. .c.ccicscisesscsecsesstessvnernesscsocssaate Used to set the game options.

VO TEST —asvnsnssnanguenazesvessuneasengeozasnescnneaeed Used for testing switches, lamps and camera. MONITOR TEST... eee eeeeeeeeeeeeneeees Used for setting the monitor.

SOUND TEST ounces Used for setting the volume.

ADS DATA —_ sisisesvsssivsesustaccestonscvesnctacsorseort Used to view bookkeeping.

OTHERS —eeeeeeceteeeeteteeeeeneeees Used for testing the PCB.

The internal battery’s dead ou... Only displayed when the battery is faulty (Refer to your Distributor).

gcELECT SW: CHOOSE ENTER SW: ENTER)

Page 44

6-3-1

Coin Options

Select “COIN OPTIONS” on the menu screen to set the game cost and related settings. The following screen is displayed.

Use the Select Up/Down switch to choose the required item then press the Enter button.

Use the Select Up/Down switch to change the setting.

Select “EXIT” and press the Enter button to return to the menu screen.

Note:- The price of play on this machine is set within the Cashflow Coin Mech. Ensure that the Game Cost is set to 1 Coin 1 Credit.

(— > COIN OPTIONS <DEFAULT IN GREEN>

GAME COST (1P) 1 COIN (S) 1 CREDIT. DISCOUNT CONTINUED 1 COIN(S) 1 CREDIT.

FREE PLAY OFF etfs (c)

EXIT

\_ UP/DOWN : SELECT ENTER SW: ENTER

Item Description Default

  • Game Cost Coins required for number of credits ---- settable 1~9 1 Coin 1 Credit
  • Discount Continue Allows reduced price of play for continue game ---- settable 1~8 or OFF. (Not used with cashflow) OFF
  • Free Play No coins required for credit ---- On (Yes) / Off (No) OFF
Page 45

6-3-2. Game Options

  • Select “GAME OPTIONS’ on the menu screen to set the game variables, the following screen is displayed.
  • Use the Select Up/Down switch to choose the required item then press the Enter button.
  • Use the to Select Up/Down switch to change the setting.
  • Select “EXIT” and press the Enter button to return to the menu screen.

Ne ~\

GAME OPTIONS [1/2] [DEFAULT IN GREEN]

PCB ID. 0 LINK ON 2

UP/DOWN:SELECT ENTER SW:ENTER

Item

Description Setting Default

PCB ID One unit, two seat setup : set to 0, 1 with 0 on the left game PCB looking at the monitors. Two units, four seat setup : set to 0, 1, 2, 3 with O on the left game PCB looking at the monitors. 0to3 0

LINK CHECK ON n (n= number of PCBs linked) : Communications are working correctly. OFF : There is no incoming communication data. NG : Communication data is not recognised. The game cannot be played correctly if OFF or NG is displayed. Contact your distributor for assistance.

Page 46

6-3-3 I/O Test

  • Select “I/O TEST” on the menu screen to test the gun,switches and camera. The following screen is displayed.
  • Use the Select Up/Down switch to choose the required item then press the Enter button to enter the test.
  • Select “EXIT” and press the Enter button to return to the menu screen.

( > VO TEST

DIP 4 12345678 [ON:RED] —eseecesssesssssssssesseeafeccsssssseeeseeoee (a)

LINK ON 2 hinccsesssttttsesssteesesafecesssesseeeseeeee (b)

WO PCB CHECK — i haececceetetesetetesttstsefeseeseessesesees (c) HOW TO [I/F] INITIALIZE caseeeesssscsscssssssssssse)ccccsssseenessss (d)

GUN TEST (e)

GUN INITIALIZE ceesseeeesessssteeseests|eeceesteeeeeeeee (f) SWITCH TEST aneeesssessssssttesseests| eeceesseeeeeeeee (g) CAMERA CHECK ceececessssssstesesssstise) osseeeseesseees (h)

EXIT

SELECT SW: CHOOSE ENTER SW: ENTER Ne 7

  • Shows the condition of the DIP Switches on the PCB. In normal operation all switches are OFF. (If a switch is ON, it will be displayed in red.)
  • Shows how many players are linked and condition of link.
  • Checks function of I/O PCB. (see Section 6-3-3-1 page 47)
  • Initialize game potentiometers. (see Section 7 page 56)
  • Selecting this item allows the gun aim to be checked. (See 6-3-3-3 page 48)
  • This item allows the gun accuracy to be set (see 6-3-3-4 page 49)
  • This item allows the testing of the switches. (See 6-3-3-5 page 50)
  • This item allows the testing and setting of the camera. (See 6-3-3-4 page 49)
Page 47

6-3-3-1 1/0 PCB Check

  • Select ‘I/O PCB CHECK’ from the I/O Test Screen. The following screen is displayed:-

(— >) VO TEST DIP 4 12345678 [ON=RED] LINK ON2

1/0 PCB CHECK

Master JV TX 3536 NAMCO LTD. ; GM; VER 0.766; JPN

1/0 PCB CONNECT OK NAMCO LTD. ;ASCA-3; VER2.04 JPN, MULTIPURPOSE + ROTARY ENCODER

ENTER SW: ENTER

NS 7

Note: This screen is for information only. No adjustments are available.

6-3-3-2 How to [I/F Initialize]

Select ‘How to [I/F Initialize]’ from the I/O Test menu. The following screen is displayed.

( >) VO TEST

DIP 4 12345678 [ON=RED] LINK ON 2

HOW TO [I / F INITIALIZE]

W/F INITIALIZE : (1) OR (2)

  • HOLDING SERVICE SW AND TURN ON TEST SW
  • SELECT [GUN INITIALIZE] ON 1/0 TEST

ENTER SW : ENTER

Ne 7

Note: Initialization cannot be executed from this screen. (see 7 page 56)
Page 48

6-3-3-3 Gun Test

  • Select ‘GUN TEST’ from the I/O Test Screen. The following screen is displayed:-

( 0 TEST )

DIP 4 12345678 [ON=RED] LINK ON 2

GUN TEST GUN TRIGGER OFF

SOLENOID OFF

GUN LED OFF GUN YAWING RIGHT 0000 GUN YAWING LEFT 0000

SLIDE FORWARD 0000 SLIDE BACK 0000 SLIDE RIGHT 0000 SLIDE LEFT 0000 EXIT

ENTER SW: ENTER NS J

  • Select EXIT and press the Enter button to return to the I/O TEST screen.

Upon selecting the GUN TEST screen, the blue LED on the gun will flash on and off regularly.

Note about the blue LED: The GUN LED on the display will change alternately between ON and OFF as the blue LED flashes on and off. If the gun trigger is operated during this test, the GUN TRIGGER, SOLENOID and GUN LED displays will change to green, the blue LED will flash dimly and the solenoid will operate.

. Twisting the gun left and right will cause the numbers displayed against GUN YAWING RIGHT and GUN YAWING LEFT to change (about -1350 ~ 1350). OK will be displayed just before the gun is twisted fully left or right.

. Sliding the gun left, right, forward or backward will cause the numbers displayed against SLIDE FORWARD, SLIDE BACK, SLIDE RIGHT and SLIDE LEFT to change (about -900 ~ 1500 forward, - 1500 ~900 backward and -1200 ~ 1200 left and right). OK will be displayed just before the limit of travel.

Note: If OK is not displayed as above initialize the gun. (see section 6-3-3-4 page 49).
Page 49

6-3-3-4 Gun Initialize

  • Select ‘GUN TEST’ from the I/O Test Screen. The following screen is displayed:-

~\ ( GUN INITIALIZE

AIM AT CENTER OF THE CROSS AND PUSH SERVICE BUTTON

GUN YAWING | Median point _ | x Median point

SLIDE FORWARD 0000 LEFT RIGHT 0000 0000 BACK 0000

TRIGGER : ADJUST SLIDE AND SIGHT \_ ENTER SW: ENTER S

  • As the gun is twisted left or right, the sight marked by “X” moves accordingly. When the sight reaches a maximum value (i.e. when it moves to the extreme left or right of the screen), the “X” will change colour.
  • Ensure that the gun is completely central of all travel and then press the service button to reset all values.
  • Select EXIT and press the Enter button to return to the I/O TEST screen.
Page 50

6-3-3-5

1. Switch Test

Select “Switch Test” on the I/O menu screen to test the switches. The following screen is displayed.

The display shows the current state of the switches.

Press the Up Select switch and the Enter switch together to EXIT and return to the I/O menu screen

( 1/0 TEST >

DIP 4 123456787 [ON/RED]

SWITCH TEST COIN 0. SERVICE OFF .. TEST ON .. SELECT OFF .. ENTER OFF ..

UP SELECT + ENTER: EXIT

X yy,

Not Used

c,d) Display will change from OFF to ON each time a switch is Operated.

Display will change to UP or DOWN as the select is operated.

Page 51

6-3-3-6 Camera Check

1. Select ‘CAMERA CHECK’ from the I/O Test Screen. The following screen is displayed:-

\_ UP/DOWN : SELECT ENTER SW: ENTER ) ~ VO TEST

CAMERA CHECK [DEFAULT IN GREEN]

MIRROR ———heecccssecsessseeee

IRIS ADJUST DIIIMIIIB

TINT ADJUST GIIIMIIIR

V POSITION +000

H POSITION 4000 ceeccsceseeed

EXIT

SERVICE SW : TAKE A PHOTO/RELEASE

(a) In the CAMERA CHECK Screen, the current view of the camera is displayed in the centre box.

MIRROR/PHOTO By pressing the Service Switch, the image from the camera is frozen on the screen and the word MIRROR, just below the image box, changes to PHOTO. This is the image that would be used during the game. Pressing the Service Switch again reverts back to current camera image, and the word PHOTO changes to MIRROR. The mode of [MIRROR] is used for adjustment of the image, and the mode of [PHOTO] to verify the picture to be used during the game.

IRIS ADJUST This setting is used to adjust the brightness of the image. The brightness of the image is automatically adjusted to the optimum value by the system, but this item allows the brightness level to be set manually. Select this item and press the ENTER button. Use the Select UP/ DOWN switch to make the image brighter or darker. There are three brighter and three darker settings available. Press the ENTER button to store the new setting and to exit this mode.

Page 52
  • TINT ADUST This setting is used to adjust the colour tint of the image. The colour tint of the image is automatically adjusted to the optimum value by the system, but this item allows the colour tint level to be set manually. Select this item and press the ENTER button. Use the Select UP/DOWN switch to increase or decrease the red tint. The red tint can be increased or decreased by three levels each. Press the ENTER button to store the new setting and to exit this mode.
  • V POSITION This setting is used to set the vertical position of the camera view. Select this item and press the ENTER button. Use the Select UP/DOWN switch to move the camera view up or down. Press the ENTER button to store the new setting and to exit this mode.
  • H POSITION This setting is used to set the horizontal position of the camera view. Select this item and press the ENTER button. Use the Select UP/DOWN switch to move the camera view left or right. Press the ENTER button to store the new setting and to exit this mode.

. Select EXIT and press the Select Button to return to the I/O Test Screen.

Adjustment of the Camera

Adjust the camera to obtain the best image by following the steps below.

  • Verify moving images. Make sure that the image in the test screen box is moving. If a still picture is shown press the Brake Pedal once.
  • Adjust the image quality. Check the brightness and colour tint of the image and if neccessary adjust by following steps (b) and (c) above.
  • Adjust the position. Make any adjustments neccessary by following steps (d) and (e) above whilst checking the image displayed.
Page 53

6-3-4 Monitor Test

  • Select “MONITOR TEST” on the menu screen to test and adjust the Monitor. The following screen is displayed.
  • Use the Select Up/Down switch to choose the required item then press

the Enter button. To return to the Monitor Test Menu from a test pattern

press the Enter button.

  • Select “EXIT” and press the Enter button to return to the menu screen.

( MONITOR TEST >

GRADATION PATTERN CROSSHATCH PATTERN (CRT) CROSSHATCH PATTERN (PROJ) WHITE WINDOW (H) WHITE WINDOW (M) WHITE WINDOW (L) INTERLACE PATTERN VIEW ANGLE ADJUST (CRT) VIEW ANGLE ADJUST (PROJ) FULL WHITE EXIT

LL UP/DOWN : SELECT ENTER SW: ENTER

Note: Items (c) and (i) are not used on this game.
  • Displays vertical colour bars.
  • Displays a crosshatch pattern for CRT monitors.
  • Displays a crosshatch pattern for projection monitors (not used on this game).
  • Displays a white square (bright).
  • Displays a white square (medium)
  • Displays a white square (dim)
  • Displays an interlaced pattern.
  • Displays a pattern for height/width adjustment for CRT monitors.
  • Displays a pattern for height/width adjustment for projection monitors (not used on this game).
  • Outputs white to the full screen area.
Page 54

6-3-5

1. Sound Test

Select “SOUND TEST” on the menu screen to test the audio and adjust the volume settings. The following screen is displayed.

Use the Select Up/Down switch to choose the required item then press the Enter button.

Use the Up/Down switch to change the setting.

Press the Enter button to return to item select mode

Select “EXIT” and press the Enter button to return to the menu screen.

\ SOUND TEST <DEFAULT IN GREEN>

VOLUME ALL SP FRONT L SP (00~64) FRONT R SP (00~64) ATTRACT SOUND VOL

REQUEST SONG NO. (0 ee (e)

MESSAGE :

EXIT

SERVICE : REQUEST ON/OFF UP/DOWN : SELECT ENTER SW: ENTER

/

Adjusts the volume of the left and right speakers together.

Adjusts the volume of the left speaker only.

Adjusts the volume of the right speaker only.

Adjusts the volume level during attract mode.

Each number produces a different sound each time the service button is

pressed. (The sound will be turned off by pressing the service button or automatically after approx 10 seconds)

Number 001 will produce a stereo test. Sound will be produced from the left speaker then the right speaker and then both speakers together. The message on the screen will display which speaker is active.

Page 55

6-3-6 ADS Data

By selecting ADS Data from the menu screen, all of the bookkeeping details can be read and/or reset.

6-3-7 Others

  • Select “OTHERS” on the menu screen. The following screen is displayed.
  • Use the Select Up/Down switch choose the required item then press the Enter button.
  • Select “EXIT” and press the Enter button to return to the menu screen.

( OTHERS >

ROM1Ver. 97/07/07 21:15:59

CLOCK alo _ wteeton PCB TEST LANGUAGE ENG BACKUP MEMORY INITIALIZE

EXIT

UP/DOWN : SELECT ENTER SW: ENTER

Ne w

(a,) Displays game software version.

  • Not used on this game
  • Used to test the PCB. (this function is only for factory testing)
  • Sets the language displayed on the screen. (English:ENG, German:GER, French:FRA, Spanish:SPA,

Portugese:POR, Italian ITA)

  • When selected the Data Initialization Menu appears. To reset all game settings to factory setting and clear all stored data , select YES from the Data Initialization menu then press the Enter button.

After initializing the backup data ensure that the game is reinitialized. (see section 7 page 56)

Page 56
  • INITIALIZATION

Adjustments when Replacing Parts

The following operation must always be performed after replacing the Game PCB, Rom, or Control Potentiometers. The game will not operate correctly if these adjustments are not made.

  • Slide the TEST switch ON while pressing the SERVICE switch . The following screen is displayed.

(— > GUN INITIALIZE

AIM AT CENTER OF THE CROSS AND PUSH SERVICE BUTTON

GUN YAWING x

SLIDE FORWARD 0000 LEFT RIGHT 0000 0000 BACK 0000

TRIGGER : ADJUST SLIDE AND SIGHT

Ne ENTER SW : ENTER

S

  • Ensure that the gun is completely central of all travel and then press the service button to reset all values.
  • Slide the Test switch OFF to return to normal game mode.
Page 57
  • MAINTENANCE A

Adjustment or maintenance on this machine should be carried out by qualified personnel only. Ensure that the POWER to the machine is turned OFF before commencing any maintenance work. (Trouble shooting, service or repairs etc.)

® Einstellungen und Wartung des Gerates diirfen nur von dafiir qualifiziertem Fachpersonal vorgenommen werden. Vor Beginn aller Wartungsarbeiten (Fehlersuche, Reparaturen etc.) mufB& der Netzstecker gezogen werden.

@®) Justeringer eller vedligehold af denne maskine bor kun udfores af

kvalificeret personale. Sorg for, at strammen til maskinen er slukket for der foretages nogen form for arbejde (fejlfinding, reparation etc.)

© Los ajustes y el mantenimiento de esta maquina deben ser realizados s6lo por personal cualificado. Asegurese de que la maquina esta desconectada antes de comenzar cualquier trabajo de mantenimiento (reparaciones, resolucién de problemas, etc.)

©) L’installation, le service, le réglage, ou la maintenance doivent étre effectués uniquement par les personnes qualifiées. S’assurer que |’interrupteur soit sor OFF avant de commencer tout travail de maintenance (localisation d’une panne, réparations, etc.)

@ Metatponéc f emdiop@woeicg ota pnXavAypata mpéne va yivovtal HOvo amo e€ouciodoTHpEva AaToua. Na eivai ciyoupa KAEIoTO To peUpG MpIV omoladHMoTE SouAEIG OTO unxavnya.

& Regolazioni e manutenzione su questa macchina devono essere fatti solo da personale specializzato. Assicurarsi che la macchina sia SPENTA prima di incominciare qualsiasi lavoro di manutenzione (guasti, riparazioni etc.)

@®) Justering eller vedlikehold pa denne maskinen skall bare utfores av kvalifiserte personell. Forsikre deg om at strommen er slatt av for du pabegynner noe som helst vedlikeholdsarbeid (feilsoking, reparasjon osv.)

Page 58

A

@ Aanpassingen of onderhoud aan deze machine dient alleen uitgevoerd te worden door bekwaam personeel. Zorg ervoor dat de machine UlTgeschakeld is voordat er enig onderhoudswerk wordt verricht (troubleshooting, reparaties etc.)

® Afinag6es ou manutengao nesta maquina, deverao ser efectuadas somente por pessoal qualificado. Certifique-se que a maquina se encontra desligada sempre que iniciar qualquer tipo de trabalho de manutengao. (identifagao de avarias, reparagao etc.)

® Justeringar och underhall pa denna maskin skall endast utféras av kvalificerad personal. Foérsakra dig om att str6mmen ar avstangd innan underhallsarbete paborjas (felsékning, reparationer etc.)

G Tata laitetta saa saataa tai huoltaa vain siihen ammattipatevyyden omaava henkilékunta. ae Varmista, etta laite on kytketty POIS PAALTA ennen ty6n aloittamista.

Page 59

8-1 Greasing the Gun Assembly

Greasing should be performed every six months.

  • Remove 4off security screw (M5x16) and remove the Gun Vac-form

Upper,

  • Remove 15off security screw (M5x20) and remove the Gun Vac-form Lower.

Security screw (M5 x 16) _- Security screw (M5 x 20)

Gun Vacform Secutity screw (MS x 16) Security screw Upper ¥——— (ms x 20)

Gun Vac-form Security screw (MS x 20)

Security screw (Ms x 20)

Security screw (MB5 x 20) Gun Vac-form Lower

  • Grease the circumfrance of the bearings.

Recommended grease : Castro! LM30 or equivalent.

Greasing point

Greasing point

Page 60

8-2 Replacing the Fluorescent Lamp or Starter

  • Remove 6off security screw (M5x16) and remove the Lower Retaining bracket and Header Acrylic.

Security screw (M5 x 16)

tT TAM WAR

+=>———— Lower Retaining Brkt fe

  • Replace the fluorescent lamp and/or starter. Header Acrylic rid (es \] \ poh

\ / Starter

  • Reassemble in reverse order.
Page 61

8-3 Replacing the Gun Assembly

  • Remove the Gun Vac-Forms Upper and Lower. (see 8-1 page 59 )
  • Remove 2off pozi head screws (M5x20) and 2off pozi head screws (M5x16), complete with spring and flat washers, and remove the Gun Frame B.

Pozi pan head screws (with plain and spring washers) (M5 x 16)

Gun frame B

Pozi pan head screws (with plain and spring washers) (M5 x 20)

  • Disconnect the connectors.
  • Remove 4off hex head screws (M8x25) and remove the Gun Assembly.

Gun Assy

Hex head screw (M8 x 25) Hex head screw (MB x 25)

  • Reassemble in reverse order.
Note: Reinitialize the gun after replacing the gun assembly (see 7 page 56)
Page 62

8-4 Replacing the Gun Solenoid

SAFETY WARNING

Gun Replacement or Maintenance.

To maintain compliance with CE regulations, the following must be strictly adhered to.

When replacing the gun assembly or refitting the gun sides after maintenance, the four screws located on the gun grip must be Nylon Countersunk Head Screws (M4x12), and the Gun Grip Decals (L & R) must be fitted after the screws have been fully tightened.

Spare screws and decals are supplied with the machine at the time of delivery and must be kept in the machine and available for use at all times.

Nylon c/sunk screw (M4x12) [ex \,

Page 63
  • Remove the Gun Grip Decals L&R
  • Remove 3off cap bolts (M4x45), 1off cap bolt (M4x20), 4off hex box nuts and 4off nylon c/sunk screws (M4x12) and remove the Gun Sides Left and Right.

Cap bolt (M4 x 45) Hexagon box nut (M4) — Cap bolt (M4 x 20)

Cap bolt (M4 x 45)7 Gun grip decal

  • Disconnect the solenoid connector.
  • Remove 1off nylon nut (M4), withdraw the plunger pin and remove the barrel.

Barrel

Nylon nut (M4)

Solenoid

Page 64
  • Remove the 3off flange socket head screws (M4x8) and remove the earth wire.
  • Pull out the solenoid and spring, taking care not to lose the spring as the solenoid is withdrawn.
  • Remove the 2off retaining ‘E’-rings and remove the rubber washers from the plunger.

Retaining E-ring

Solenoid

Rubber washer

Flange socket head screw (M4 x 8)

Solenoid Ground

Spring

  • Remove the plunger from the gun frame.
  • Reassemble in reverse order, paying particular attention to the order of refitting the rubber washers, ‘E’-rings and spring.
  • Refit new Gun Grip Decals L & R.
Page 65

8-5 Replacing the Blue LED Assembly

SAFETY WARNING

Gun Replacement or Maintenance.

To maintain compliance with CE regulations, the following must be strictly adhered to.

When replacing the gun assembly or refitting the gun sides after maintenance, the four screws located on the gun grip must be Nylon Countersunk Head Screws (M4x12), and the Gun Grip Decals (L & R) must be fitted after the screws have been fully tightened.

Spare screws and decals are supplied with the machine at the time of delivery and must be kept in the machine and available for use at all times.

Nylon c/sunk screw (M4x12) | ic)

  • Remove the Gun Sides (L & R). (See 8-4 page62)
  • Disconnect the connector.
  • Replace the blue LED and reassemble in reverse order.
  • Refit new Gun Grip Decals L & R.
Page 66

8-6 Replacing the Trigger Microswitch

SAFETY WARNING

Gun Replacement or Maintenance.

To maintain compliance with CE regulations, the following must be strictly adhered to.

When replacing the gun assembly or refitting the gun sides after maintenance, the four screws located on the gun grip must be Nylon Countersunk Head Screws (M4x12), and the Gun Grip Decals (L & R) must be fitted after the screws have been fully tightened.

Spare screws and decals are supplied with the machine at the time of delivery and must be kept in the machine and available for use at all times.

Nylon c/sunk screw (M4x12)

Gun side (R) Gun side (L) —\ Nylon c/sunk screw (M4x12)

‘| —~Gun grip decal

Page 67
  • Remove the Gun Sides (L & R). (See 8-4 page 62)
  • Disconnect the microswitch connector.
  • Remove the 2off flange head screws (M3x6) and remove the microswitch complete with bracket.
  • Remove 2off pozi pan head screws (M2.3x10), with flat and spring washers, and remove the microswitch.

Bracket

Flange socket head screw (M3 x 6)

Pozi pan head screw with plain and spring washer)

Microswitch tie 10) pring )

  • Replace the microswitch, taking care that the microswitch wires are connected to the correct terminals.

Microswitch wiring

Microswitch

i Brown Brown (COM) (N.C.)

  • After replacing the trigger microswitch ensure that it is working properly when the trigger is squeezed.
  • If the switch does not operate correctly adjust it by loosening the 2off flange socket head screws (M3x6) and sliding the switch bracket backwards or forwards. When the switch is operating correctly retighten the 2off flange socket head screws (M3x16).
  • Reasemble in reverese order.
  • Refit new Gun Grip Decals (L & R).
Page 68

8-7 Replacing the Backward / Forward Potentiometer

  • Remove the Gun Vac-Forms. (See 8-1 page 59)
  • Remove the gun Frame. (See 8-3 page 61)
  • Remove 4off cup screws (S) (M4x10) and remove the Slide Cover (S).
  • Remove 4off counter sunk-type washer nuts (M5) and Slide Covers (R &L).

Slide cover (S) Cup screw (S) (M4 x 10)

Cup screw (S) (M4 x 10) Countersunk-type washer out (M5)

Page 69
  • Disconnect the potentiometer connector.

Double-point (M4 x 6)

Actuator Arm

  • Loosen the double point screw (M4x6) and remove the actuator arm.
  • Replace the potentiometer.
Note: When replacing the potentiometer ensure that the double point screw (M4x6) engages on the flat of the potentiometer shaft, and that the correct colour wires are connected to the correct terminals.

Whi/Red Whi/BIk Whi/Vio

  • Reasemble in reverse order.
NOTE: After replacing the potentiometer REINITIALIZE the game. (see section 7 page56).
Page 70

8-8 Replacing the Left / Right Slide Potentiometer

Remove the Gun Vac-Forms. (See 8-1 page 59)

  • Remove the gun Frame. (See 8-3 page 61)
  • Remove the slide covers (S), (R) and (L). (See 8-7 page 68).
  • Disconnect the potentiometer connector.

Double-point (M4 x 6

Actuator Arm

  • Loosen the double point screw (M4x6) and remove the actuator arm.
  • Replace the potentiometer.
Note: When replacing the potentiometer ensure that the double point screw (M4x6) engages on the flat of the potentiometer shaft, and that the correct colour wires are connected to the correct terminals.
  • Reasemble in reverse order.

Whi/Red WhilBik Whi/Blu

NOTE: After replacing the potentiometer REINITIALIZE the game. (see section 7 page 56).
Page 71

8-9 Replacing the Left / Right Potentiometer

1.

2.

6. Remove the Gun Vac-Forms. (See 8-1 page 59)

Remove the gun Frame. (See 8-3 page 61)

Remove the slide covers (S), (R) and (L). (See 8-7 page 68).

Disconnect the left/right slide potentiometer connector. (See 8-8 page 70)

Remove 6off flange socket heads screws (M6x12) and remove the gun assembly by lifting it straight up.

Flange socket head screw (M6 x 12)

Flange socket head screw (M6 x 12)

Remove the cup screw (S) (M4x10), loosen the double point screw (M4x6) and remove the potentiometer complete with mounting bracket.

Double-point (M4 x 6)

Connector

___— Pot bracket

Cup screw (S) (M4 x 10)

Page 72
  • Replace the potentiometer.
Note: When replacing the potentiometer ensure that the double point screw (M4x6) engages on the flat of the potentiometer shaft, and that the correct colour wires are connected to the correct terminals.

Connector

Plain washer

Potentiometer Pot bracket

3 oN

Whi/Red Whi/Bik

Whi/Gry

  • Reasemble in reverse order.
NOTE: After replacing the potentiometer REINITIALIZE the game. (see section 7 page 56 ).
Page 73

8-10 Replacing the Monitor

The monitor weighs approx 40kg. Ensure that at least two people are available to remove the monitor.

  • Seperate the Front assembly from the Monitor Cabinet. (See 5-1 page 39)
  • Loosen the lower 2off pozi head screws (M5x25) on the maintenance panel on the rear of the monitor cabinet, remove the 2off upper pozi head screws (M5x25), and remove the maintenance panel.
  • Disconnect the monitor connectors and earth terminal.

i] Pozi head screw (M5 x25)

Pozi head screw (M5 x25) (to be loosened)

Page 74
  • Remove 10off security screw (M5x16) and remove the Monitor Vac-form.

Security screw (M5 x 16)

Security screw (M5 x 16)

Security screw (M5 x 16)

Monitor Vac-form

Page 75
  • Remove 4off pozi head screws (M8x25), with spring and special flat washers.

Pozi head screws (M8x25) (with flat and spring washers)

Washer

Pozi head screws (M8x25) (with flat and spring washers)

  • Tilt the monitor forward from the top and lift the monitor out of the cabinet.
  • Reassemble in reverse order.
Page 76

8-11 Replacing the Camera

  • Remove 6off Security screw (M5x16).
  • Lift the Camera assemblyy forward carefully, and disconnect the connector.

Connector a Camera Assy

Security screw (M5 x 16)

  • Remove the Camera assembly.
  • Remove 4off pozi head screw (M4x10) and remove the Camera Housing.
  • Remove the Camera PCB by carefully pushing the retaining clips outward.

Pozi head screw (M4 x 10)

Camera

  • Reassemble in reverse order.
Page 77
  • PARTS Main Cabinet

Item Description Part No

1Monitor Surround Vac-form46000944
2Monitor - Hantarex PoloMedium Planar 28"84000001
3Speaker Grille46000952
4Loudspeaker - 47%"62000006
7Internal Reinforcing Bracket46000947
8Side Decal (LHS)40000482
9Side Decal (RHS)40000483
10Front Decal (LHS/RHS)40000484
21Adjustable Foot - M1688300079
22Swivel Castor - 75mm59000005
Page 78

Gun Cabinet

Page 79

Item Description Part No

2Header Support Tube (LHS / RHS)46000953
4Tube Reinforcing Bracket A46000954
5Gun Cabinet Joint Bracket46000955
11Gun Top Vac-form46000960
12Gun Vac-form Lower46000961
13Gun Forward Cover Vac-Form46000962
14Cabinet Side Decal - LHS40000486
15Cabinet side Decal - RHS40000487
16Cabinet Front decal40000488
17Gun top Vac-Form Front Decal40000489
18Play Instruction Decal40000490
19Pipe Decal - LHS40000491
20Pipe Decal - RHS40000492
21Pipe Hazard Decal40000493
22Gun Vac-Form Side Decal - RHS40000496
23Gun Vac-Form Side Decal - LHS40000495
30Adjustable Foot - M16x9588300079
31Swivel Castor - 75mm59000005
Page 80

Camera Assy

& br.

Item Description Part No

1Camera Mounting Bracket46000951
2Camera 'Namcam' Decal40000485
3Camera AssemblyXRO-686-050
Page 81

Mains-In Assy

O° [e)

|) Sy

o| OT

  • [e)

©) ©

Item Description Part No

1|Repeater PCB (Link PCB)-LINK PCB

2 | Schaffner Boot 66000017

3.|Schaffner Mains In Filter Assy62500010
4|Fuse Holder63500786
620mm 500mA Q/B Fuse63500608
7‘|Link Cover Bracket46000904
Page 82

Gun Assy (1 of 3)

Item Description Part No

1BaseXGW-686-212
2Sloder AXGW-686-213
3Spring CoverXGW-686-220
4Spring PinXGW-686-221
5Spring RollerXGW-686-222
6Stopper BracketXGW-686-225
7Stopper Rubber AXGW-686-226
8VR RodXGW-686-228
9VR Bracket BXGW-686-230
10|VR RollerXGW-686-231
11.|SpacerXGW-686-232
12|SpringBXGW-686-239
13|Bearing (IDS-30-B1.5-Mx11_.XGW-103-095
14|PotentiometerX008-023
Page 83

Gun Assy (2 of 3)

Item Description Part No

1Slider BXGW-686-214
2Top CoverXGW-686-215
3Top Cover BracketXGW-686-216
4Spring GuideXGW-686-217
5Spring SpacerXGW-686-218
6Spring RodXGW-686-219
7Spring PinXGW-686-221
8Spring RollerXGW-686-222
9Stopper ShaftXGW-686-233
10|Stopper RollerXGW-686-234
11|Stopper Rubber BXGW-686-237
12_|VR Bracket AXGW-686-239
13|VR RollerXGW-686-231
14|SpacerXGW-686-232
15|WasherXGW-686-233
16|Bearing (IDS-30B 1.5-M6x11)XGW-103-096
17|PillowXGW-103-046
18|SpringAXGW-686-238
19|Key (6x6x40 double angle S50C)XGW-107-035
20|PotentiometerX008-023
Page 84

Gun Assy (3 of 3)

Item Description Part No

1Main ShaftXGW-686-211
2(Grip CoverXGW-686-234
3Slide Cover (R)XGW-686-235
4Slide Cover (L)XGW-686-236
5Slide Cover SXGW-686-237
6Spring CXGW-686-240
7[Gun Cover (L)) GXGW-686-281
8Gun Cover (R) GXGW-686-282
9|Gun FrameXGW-686-245
10|TriggerXSG04-246-109
11{BarrelXGW-246-110
12|Plunger RubberXGW-246-112
13|Rail (R)XGW-246-115
14Rail (L)XGW-246-116
15|Switch BracketXGW-686-244
16|Roller PinXGW-246-121
17|Roller SpacerXGW-246-122

18 | Trigger Pin XSG-246-123 19 | Trigger Spring XSG-246-129

20|RollerXGW-246-139
21|Solenoid (T1261214A)XGW-004-539
22|Plunger PinXGW-686-246
23|Microswitch (SS-01GL 13T)XGW-000358
24|LED Lamp (HRX0198-BLUE)XGW-002-238
25|E-RingXGW-118-600
26|Gun Grip Decal (LHS)40000505
27|Gun Grip Decal (RHS)40000506
28|Nylon Countersunk Head Screw (M4x12)26300364
Page 85

Header Assy

Af q

wa

Item Description Part No

1Header Vac-form46000964
5Header Vac-Form Lower Closing Bracket46000968
8Traffic Light Decal40000497
9Header Vac-Form LHS Decal - 30MPH40000498
10|Header Vac-Form RHS Decal - Diversion40000499
12|Header Vac-Form Name Decal40000500
13|4' Fluorescent Fitting (Complete)64000045
14|4' Fluorescent Tube64500039
Page 86

Service Bracket

©

Item Description Part No

Panel Mounting Fuse Holder 63500786

'Fuse - 20mm 2Amp Q/B63500501
2Panel Mount Meter65000002
3Push Button Switch - 7mm Red - F42460000059
4Miniature Slide Switch60000023
5Momentary SPDT Toggle Switch60000010
Page 87
  • SCHEMATIC

i

g veo me = bry ‘ie Zz é g

La} i

ee Taurens]

Sg

ie. = My ad | = LE