CATHODE RAY TOMES

Bally Midways MCR System Games Standardized General Instructions (M051-00986-A025)

MCR System Games (Bally/Midway, 1983) · Manual · 105 pages · 56 sections · original scan

Page 1

= Gumare MCR

System Games

__ MIDWAY MFG.CO. '10601'W. Belmont Avenue | : Franklin rary irots 6p 31

Page 2

WARNING

THIS GAME MUST BE GROUNDED. FAILURE TO DO SO MAY RESULT IN DESTRUCTION TO ELECTRONIC COMPONENTS.

WARNING: This equipment generates. uses. and can radiate radio frequency energy and if not and used in accordance with the instructions manual. may cause interference to radio communications. It has been tested and found to comply with the limits for a CLASS A computing device pursuant to SUBPART J of PART 15 of FCC RULES. which are designed to provide reasonable protection against such interference when operated in acommerical environment. Operation of this equipment ina residential area Is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.

ELECTRICAL BULLETIN: FOR ALL APPARATUS COVERED BY THE CANADIAN STANDAROS ASSOCIATION (CSA) STANDARD C22.2 NO. 1, WHICH EMPLOYS A SUPPLY CORD TERMINATED WITH A POLARIZED 2-PRONG ATTACHMENT PLUG.

CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET

metry THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE

URE.

ATTENTION: POUR PREVENIR CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR. UNE PRISE DE COURANT OU_UNE_ AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT.

Cially MIDWAY ” Iauttes You Te Use our TOLL FREE numeers FoR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER BALLY MIDWAY GAME YOU NOW HAVE ON LOCATION.

CALL US FOR PROMPT, COURTEOUS

ANSWERS TO YOUR PROBLEMS. VIDEO === Continental U.S. 1-800-323-7182 PINBALL == Continental U.S. 1-800-323-3555 MIDWAY —— 1060! west Betmont avenue, Franklin Park. IIlinors, 60191 phone (312)451-9200 TM.

© COPYRIGHT MCMLXXXIII BY BALLY/MIDWAY CO. ALL RIGHTS RESERVED. NO PART OF THIS PUBLICATION MAY BE REPRODUCED BY ANY MECHANICAL, PHOTOGRAPHIC, OR ELECTRONIC PROCESS, OR IN THE FORM OF A PHONOGRAPHIC RECORDING, NOR MAY IT BE TRANSMITTED, OR OTHERWISE COPIED FOR PUBLIC OR PRIVATE USE, WITHOUT PERMISSION FROM THE PUBLISHER. THIS MANUAL IS FOR SERVICE USE ONLY, AND NOT FOR GENERAL DISTRIBUTION. FOR PERMISSION REQUESTS, WRITE: MIDWAY MFG. CO., 10750 W. GRAND AVE., FRANKLIN PARK, IL 60131 Printed in U.S.A.

Page 3

TABLE OF CONTENTS

DESCRIPTION

|. Location and Setup Inspection. . Installation . Game Volume ‘Adjustment control. Option Switch Settings ........... Cocktail Table Leg Extension installation

|. Maintenance and Repair 2.1 INtPOdUCTION 00... cece e nen ene EEE EEE Ene EE n een EES 2.2 Cleaning 2.3 Fuse Replacement 2.4 Opening Control Panel 2.4.1 Upright Model ... 2.4.2 Mini Model .... 2.4.3 Cocktail Model 2.5 Main - Display - Glass Removal 2.5.1 Upright Model . . 2.5.2 Mini Model .. Sane ee ene e cena net eeseenee 2.5.3 Cocktail Model 2.6 T.V. Bezel Assembly Removal . 2.6.1 Upright Model 2.6.2 Mini Model .... 2.6.3 Cocktail Model 2.7 T.V.Monitor Replacement 2.7.1 Upright Model 2.7.2 Mini Model .... 2.7.3 Cocktail Model 2.8 Printed Circuit Board (P.C.B.) Replacement 2.8.1 Upright Model . 2.8.2 Mini Model . 2.8.3 Cocktail Model 2.9 Opening the Upper Attraction Panel 2.9.1 Upright Model . 2.9.2 Mini Model . 2.10 Replacing the Game Upper Attraction Panel Lighting . 2.10.1 Upright Model 2.10.2 MiniModel . 2.11 Speaker Replacement 2.11.1 Upright Model 2.11.2 Mini Model . 2.11.3 Cocktail Model . anece pen gee 2.12 Opening the Lower Attraction Panel and Servicing it 's Lighting Assemb ly. 2.12.1 Upright Model oa 2.13 Servicing the Control Panel Lighting Assembly 2.13.1 Upright Model ............cce cree ee 2.14 Servicing Auxiliary Lighting ............:.eeee eee eee 2.14.1 Upright Model - Servicing Windshield Fluorescent Light 2.14.2 Upright Model - Servicing the Black Light Above Control Console . . 2.14.3 Upright Model - Servicing the Fluorescent Light Behind the Front Service | Panel gions

iti

Page 4

TABLE OF CONTENTS (Continued)

DESCRIPTION PAGE

I, Technical Troubleshooting Introduction 3-1 General Suggestions . 3-1 Harness Component Troubleshooting ... 3-1 Transformer and Line Voltage Problems. . 3-2 A Glossary of Microprocessor Terms 3-3

IV. Coin Door Maintenance Metal Coin Acceptor Mechanisms 41 Plastic Coin Acceptor Mechanisms 4-3

V. T.V. Monitor Manual Introduction 5-1 Sympton Diagnosis 5-2 Guide to Schematic Symbols . 5-3 Troubleshooting ..... 5-5 Theory of Operation .. 5-6 Differences Between Monitors ... 5-8 Controls You May Not Touch... 5-9 Parts Interchangeability ... 5-9 Picture Tube Interchangeability 5-10 Wells Gardner Monitor Schematic - 19” 5-12 Wells Gardner Monitor Replacement Parts List 5-13 Electrohome Monitor Schematic -19"...... 5-14 Electrohome Monitor Replacement Parts List . 5-15 Electrohome Monitor Schematic -13"...... 5-16 Electrohome Monitor Replacement Parts List . 5-17 Zenith Monitor- Sweep Board Schematic .. 5-18 Zenith Monitor - Sweep Board Replacement Parts List 5-19 Zenith Monitor Main Board Schematic ............. 5-26 Zenith Monitor Main Board Replacement Parts List 5-21 Zenith Monitor- CRT Socket Board Replacement Parts List . 5-22 Zenith Monitor - CRT Socket Board Schematic . . 5-23 Zenith Monitor Width Step Assy. Schematic .... 5-24 Zenith Monitor Interconnect for Video Game Schematic ......... 0.0.00. cece cece eee e eee e eens 5-25

VI. Self-TestMode 00... cee ne nner nee tnt ee ten tte 6-1

Page 5

I. Location and Setup

INSPECTION

  • Remove the game from its shipping crate.
  • Inspect the entire outside of it for any signs of damage. O Any scratches?, dents?, cracks? QO Any broken controls? D Any broken glass or plastic? O Just look it over closely and make a note of any signs of damage.
  • Remove the shipping cleats from the bottom of the cabinet. O UPRIGHT MODELS ONLY: In order to help prevent easy theft of your game, you may wish to remove the Caster Wheel Assemblies from the bottom of your cabinet at this time.
  • Install the four levelers, one at each corner of the cabinet, O Level the cabinet.
  • Open the cabinet and inspect the inside of the game for any signs of damage. See Figure 1-1. O Also check to make sure ail plug-in connectors on the wire harness are firmly seated.
NOTE: ALL connectors or plugs are keyed so they will only go together when ail pins are properly lined up. O Replug any connectors found unplugged. DO NOT FORCE PLUGS ONTO CONNECTORS. DO NOT FORCE PLUGS TOGETHER. If it won't go on easily, assuming the keys are lined up, it either does not belong there or is damaged. Make sure ail printed circuit boards (P.C.B.’s) are firmly seated in their connectors. See Figure 1-1. These connectors are also keyed. The P.C.B.’s will only go into them one way without being damaged.
Note the location of the game's serial number. See Figure 1-1. Check all major subassemblies to be sure they are mounted securely. These are called out in Figures 1-1 & 1-2. Power supply. Control panel(s). T.V. monitor. Other P.C.B.’s and/or P.C.B. rack, etc. Power Chassis assembly. QO

a

  • Make a note of any problems that can't be easily corrected.
  • Call your distributor and/or service man about your problem list.
Page 6

SERIAL NUMBER

ON/OFF SER| aoa SWITCH NUMBER TV. MONITOR

TN. MONITOR

INTERLOCK

INTERLOCK " - i ; SWITCH ‘ J POWER SUPPLY / i} POWER i P.C.B. SUPPLY z CHASSIS : NOT SEEN]

POWER SUPPLY CHASSIS ‘ ’

P.C.B. } = (NOT SEEN)

ON/OFF SWITCH

TV. MONITOR

peeri!atAY:POWER SUPPLY
SERIAL NUMBER;|iiCHASSIS

(MAY BE LOCATED ] ON ANY CORNER) POWER SUPPLY P.C.B. Logic BOARDS

CONTROL PANEL (PLAYER 2) CONTROL PANEL (PLAYER 1)

ON/OFF SWITCH

wreckayUNDER TABLE

ON PLAYER 2 (INSIDE DOOR) COCKTAIL SIDE

Figure 1-1 Location of Serial No., Interlock Switch, On/Off Switch, & Major Sub-Assemblies

Page 7

CONTROL PANEL

UPRIGHT

Figure 1-2 Major Sub-Assembiles (cont. from Fig. 1-1)

INSTALLATION

  • Location requirements:

O Power: Domestic 110 V @ 60 Hz Foreign 200 V to 240 V @ 50 Hz

O Temperature: 32° to 100°F (0° to 38°C)

O Humidity: Not over 95% relative

C Space required: Upright 32” x 25” (81cm x 63cm) APPROX. Mini 20" x 24” (50cm x 60cm) Cocktail 32" x 22” (81cm x 55cm)

C Game height: Upright 70” (175cm) APPROX. Mini 61” (153cm) Cocktail 29" ( 73cm) Figure 1-3 Interlock Switch Operation

Page 8
  • Voltage Selection: Your game is designed to work properly on the line voltage where you are located. Check your line voltage with a meter to determine what its value is. Then check the power input wires to the main power supply transformer on your game to be sure they are connected to taps which correspond to your line voltage value. If the power input wires to the main power supply transformer are not connected to taps which correspond to your local line voltage, move them to the proper taps. lf the line voltage in your area falls outside the upper or lower limits of the range of inputs covered by the main power supply transformer, DO NOT PLUG YOUR GAME IN until you have talked with your distributor and/or service man and obtained a solution to this problem. Otherwise you could damage your game.
  • Interlock and power ON/OFF switches. See Figure 1-1.

O To help prevent the possibility of getting an electric shock while working inside the game cabinet, interlock switches have been installed at each cabinet access door (this DOES NOT include the coin door in the Upright and Mini models).

When any access door is opened, the interlock switch installed there turns off all power to the game.

O Check each interlock switch for operation. After checking the line voltage in your area and determining that the input wires to the main power supply transformer of your game are connected properly — or — after obtaining a solution to your over or under voltage problem from your distributor and/or your service man, plug the game into your A.C. wall outlet. The game ON/OFF switches for all models are located as shown in Figure 1-1. Turn the game ‘on and allow it to warm up a few minutes. Slowly open each access door to the game (this does not include the coin door on the Upright and Mini models). As the door is opened approximately 1” (2.54cm) the power to the game should go off (the T.V. monitor, all the lights, and all sounds will stop). If this does not happen, check the interlock switch by this door to see if it has broken loose from its mounting or if it is stuck in the “ON” Position. proper If the switch is found to be bad, turn the game off, unplug it, and replace the interlock switch. When done, plug the game back into the wall outlet, close the access door, and turn the game back on. After the game has warmed up, repeat the above interlock switch test. When the interlock switch is working properly and turns the power to the game off, power may be restored to the game with the access door(s) Open. Take hold of the interlock switch plunger and gently pull it out to its fully extended position. THIS IS TO BE USED ONLY FOR SERVICING THE GAME. See Figure 1-3.

GAME VOLUME ADJUSTMENT CONTROL See Figure 1-4. The game volume control pot is just inside the cabinet, not far from the coin door frame. There is only one pot. For adjustment, it may be reached through the coin door. To make the sounds louder, turn the pot clockwise as you face it (~~). To make the sounds less loud, turn the pot counter-clockwise as you face it (#— ).

SERVICE CREDIT SWITCH

SELF-TEST SWITCH

VOLUME ADJUSTMENT

Figure 1-4 Game Volume Adjustment Control

Page 9

OPTION SWITCH SETTINGS

To change the most common option switch settings, you DO NOT have to take the game apart or go into the cabinet and hunt for tiny switches on P.C. boards. These most common options can be changed from the main console of the game while it is in the Self-Test mode. (See the “Self-Test section of this manual for further details.) The Self- Test switch is located just inside the cabinet not far from the coin door frame as you face it.

When changing any options, ALWAYS perform the Self-Test and play the game to be sure the ones selected are working properly. Of course, when you must change one of the switches that is located on one of the game's P.C. boards, it is also recommended that you perform the Self-Test and play the game to be sure the switches have worked Properly and that no switches were accidentally

OPTION moved that were not meant to be. (These switches are small and this can happen.)

The P.C. board option switch settings, and what they will make the game do can be found in your game's “Parts & Operating Manual.” These switches are MAINLY INTENDED for use by a technician who is checking and/or performing tests on the game. See Figure 1-5 for one example of option switch locations.

NOTE: In order to set the option switches located on the game's P.C. Boards, these Boards need not be removed from their card rack.

See your game's “Parts & Operating Manual” for exact location of these switches.

OPTION SWITCH 1

Figure 1-5 Option Switch Locations (one example)

1-5

Page 10

COCKTAIL TABLE LEG EXTENSION INSTALLATION There are two ways in which this can be accomplished: 1) the perferred method and 2) the

penal method. Both are completely covered

elow.

1. The perferred method is more labor intensive and requires 3 strong persons. Two to lift up the Cocktail Table while the third installs the Leg Extensions. A. Lift the Cocktail Table off the floor. B. Remove the Glide from each Leg. C. Install a Leg Extension in each Cocktail Table Leg that you removed a Glide from. See Figure 1-6. Make sure they are tightly screwed in place. They must not be loose. D. Reinsert the 4 Glides into the bottoms of the Leg Extensions you just installed. See Figure 1-6. E. Leg Extension installation is now complete. The alternate method is less labor intensive and requires only 1 strong person tg tilt the Cocktail Table onto its side without dropping it. This same person can then install the Leg Extensions. A. Tilt the Cocktail Table onto its side and lay it gently on the floor. Do not drop it or bounce it! B. Remove the Glide from each Leg.

C. Install a Leg Extension in each Cocktail Table Leg that you removed a Glide from. See Figure 1-7. Make sure they are tightly screwed in place. They must notbe loose. LEG EXTENSION

Figure 1-6 Cocktail Table Leg Extension Installation

D. Reinsert the 4 Glides into the bottoms of the Leg Extensions you just installed. See Figure 1-7. E. Tilt the Cocktail Table back to the upright position and recheck all the leg extensions for tightness. They must not be loose. F. Leg Extension installation is now complete.

LEG EXTENSION

Figure 1-7 Cocktail Table Leg Extension installation

Page 11

II. Maintenance and Repair

2.1. INTRODUCTION

Your NEW game needs certain types of maintenance to keep it in good working order. CLEAN, well MAINTAINED games attract players and EARN MORE PROFITS.

The most important thing for you to remember is to play your game thoroughly EVERY TIME you collect money from the coin box. JUST LOOKING at your game WILL NOT tell you if all its controls and inside parts are working correctly. ONLY being familiar with and playing your game will inform you whether or not it is working the way it should. The second most important thing you should remember is to clean the outside of the game and coin acceptor mechanisms on a regular basis. 2.2 CLEANING The outside of the game cabinet plus the metal can be cleaned with any non-abrasive household cleaner. However, the front of the T.V. monitor tube and both sides of all other glass and plastic on or in the game MUST be cleaned with anti-static cleaner ONLY. For cleaning the coin acceptors: hot soapy water may be used on the plastic ones and any household cleanser may be used on the metal ones. If you wish, special coin machine cleaners that leave no residue may be purchased from your distributor. DO NOT dry-wipe any of the plastic panels. This is because any dust that was on them can scratch their surfaces. If this has happened, anyone looking through this type of damaged plastic would feel he was looking at the game through a fog. This fogging damage CANNOT be repaired or reversed. The ONLY solution is to replace the damaged piece of plastic.

2.3 FUSE REPLACEMENT This game contains several fuses located as shown in Figure 2-1. 1, UPRIGHT MODEL:

As viewed from the back, facing the cabinet, with the rear access door removed; the fuses are located on the Power Chassis and the Power Supply Board Assemblies. . MIN] MODEL:

As viewed from the back, facing the cabinet, with the rear access door removed; the fuses are located on the Power Chassis and the Power Supply Board Assemblies. . COCKTAIL TABLE MODEL: As viewed from the coin door side of the cabinet, with the monitor tilted open to one side; the fuses are located on the Power Chassis and Power Supply Board Assemblies. Replace fuses ONLY with the type and size listed in the Illustrated Parts Breakdown Section of your game manual. See the T.V. Monitor Manual (available on request from your Distributor or the Monitor manufacturer) and/or the T.V. Troubleshooting Section of your game manual for information on these fuses.

FUSES ON POWER CHASSIS & POWER SUPPLY PCB (TYP. ALL 3 MODELS)

Figure 2-1 Location of Fuses

2-1

Page 12

2.4 OPENING THE CONTROL PANEL

2.4.1 Upright Models 2.4.2 Mini Models 2.4.3 Cocktail Models

2-2

Page 13

2.4 OPENING THE CONTROL PANEL(S) UPRIGHT

2.4.1 UPRIGHT MODEL: (See Figure 2-2)

O Thecontrol panel is held in place by two or three latches. See Figure 2-2. They are spring loaded to provide constant positive pressure on their latch plates. They can be reached through the coin door AFTER turning power to the game off. To release the latches, lift up and toward the front center of the control panel. Once they are released, unhook them from their latch plates O To remove the control panel: Raise it up and tilt it toward you until youcan see the cable behind it. Cradling the control panel between yourself and the cabinet, disconnect it from its cabling and nylon retaining strap. The control panel is now free and can be removed. O To reinstall the control panel, reverse this procedure.

CERTAIN MODELS ONLY

Figure 2-2 Opening the Control Panel - Upright

Page 14

2.4 OPENING THE CONTROL PANEL(S) (Cont'd) MINI

2.4.2 MINI MODEL: (See Figure 2-3) Q The control panel is held in place by two latches. See Figure 2-3. They are spring loaded to provide constant positive pressure on their latch plates. They can be reached through the coin door AFTER turning power to the game off. To release the latches, lift up and toward the center control panel. Once they are released, unhook them from their latch plates. QO To remove the control panel: Raise it up and tilt it toward you until you can see the cable behind it. Cradling the control panel between yourself and the cabinet, disconnect it. from its cabling and nylon retaining strap. The control panel is now free and can be removed. QO To reinstall the control panel, reverse this procedure.

Figure 2-3 Opening the Control Panel - Mini

Page 15

2.4 OPENING THE CONTROL PANEL(S) (Cont'd) COCKTAIL

CLAMPS

Figure 2-4 Opening the Cocktail Game 2.4.3 COCKTAIL TABLE MODEL: (See Figures 2-4 and 2-5)

O Each control panel is held in place by several screws, two on the inside of the cabinet and LIFT three along the outside bottom edge of the CONTROL UP control panel. Turn power to the game off. Open the coin box door and release the two REMOVE

latches indicated in Figure 2-4. Govsine

WARNING: The right hand latch is very close to the HIGH VOLTAGE on the monitor. BE CAREFUL!

Once they're released, unhook them from their latch plates. Grasp the table top at “A” and open it as REMOVE(3) indicated in Figure 2-4. SCREWS

CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet.

Remove the screws which secure the control panel in piace. See Figure 2-5. O To remove the control panel(s): Disconnect it from its cabling. The contro! panel is now free and can be removed. QO To reinstall the control panel, reverse this procedure. Figure 2-5 Removing the Control Panel - Cocktail

Page 16

2.5 MAIN—DISPLAY—GLASS REMOVAL

2.5.1 Upright Models 2.5.2 Mini Models 2.5.3 Cocktail Models

2-6

Page 17

2.5 REMOVAL OF THE MAIN-DISPLAY-GLASS UPRIGHT

2.5.1 UPRIGHT MODEL: (See Figure 2-6)

NOTE: In order to do this, the control pane} MUST be removed first. O Turn the power to the game off and remove the control panel. QO This frees the main-display-glass so it can be lifted up. DISPLAY GLASS

Q By putting your finger in the hole in the middle of the main-display-glass support, you can lift it up and out. O To reinstall the main-display-glass, reverse this procedure.

Figure 2-6 Removing the Main Display Glass - Upright

Page 18

2.5 REMOVAL OF THE MAIN-DISPLAY-GLASS (Cont'd) UPRIGHT

2.5.1 UPRIGHT MODEL: (Cont'd)

NOTE: In order to do this, the contro! panel MUST be removed first. See the "Upright Modei” procedure. C1 Turn the pwer to the game off and remove the control panel. O Remove the screws which secure the glass

clamping plate. See Figure 2-7. class

C Lift out the glass clamping plate. This frees the main-display-glass so it can be lifted up. By putting your finger in the hole in the middle of the main-display-glass support, you can lift it up and out. See Figure 2-7, O To reinstall the main-display-glass, reverse this procedure.

GLASS CLAMPING PLATE

Figure 2-7 Removing the Main Display Glass - Upright

2-8

Page 19

2.5 REMOVAL OF THE MAIN-DISPLAY-GLASS (Cont'd) UPRIGHT

2.5.1 UPRIGHT MODEL: (Cont'd)

NOTE: In order to do this, the control panel MUST be removed first. See the “Upright Model” Procedure. CQ Turn the power to the game off and remove the control panel. This frees the main-display-glass so it can be lifted up. QO Grasp the main-display-glass in the bottom center, lift up slightly and pull it toward you about an inch, let it down just far enough so you can get hold of its top edge with your other hand and lift it out of the game. See Figure 2-8. Q To reinstall the main-display-glass, reverse this procedure.

Figure 2-8 Main Display Glass Removal

2-9

Page 20

2.5 REMOVAL OF THE MAIN-DISPLAY-GLASS (Cont'd) MINI

2.5.2 MINI MODEL: (See Figure 2-9.)

NOTE: In order to do this, the contro! panel MUST be removed first. See the "Mini Model” procedure. QO Turn the power off to the game and remove the control panel. DISPLAY GLASS O Remove the screws which secure the glass clamping plate. O Lift out the glass clamping plate. This frees the main-display-glass so it can be lifted up. QO By putting your finger in the hole in the middle of the main-display-giass support, you can lift it up and out. O Reverse this procedure to reinstall the maindisplay-glass.

Figure 2-9 Removing the Main Display Glass - Mini

2-10

Page 21

2.5 REMOVAL OF THE MAIN-DISPLAY-GLASS (Cont'd) COCKTAIL

2.5.3 COCKTAIL TABLE MODEL: (See Figure 2-10)

NOTE: This may be done with the table top in the open or the closed position. If you decide to open the table top, TURN THE POWER TO THE GAME OFF FIRST. O Remove the screws which secure the table top glass clamps in place. QO Remove the table top glass. O To reinstall the table top glass, simply reverse this procedure.

2-11 Figure 2-10 Removing the Top Glass - Cocktail

Page 22

2.6 T.V. BEZEL ASSEMBLY REMOVAL

2.6.1 Upright Models 2.6.2 Mini Models 2.6.3 Cocktail Models

Page 23

26 T.V. BEZEL ASSEMBLY REMOVAL UPRIGHT

2.6.1 UPRIGHT MODEL: (See Figure 2-11)

NOTE: In order to do this, the main-display-glass MUST be removed first. See the Upright Model Procedure. O Loosen the screws which secure the T.V. bezelglass-clamps in place. Move the clamps to the side and the bezel glass may be removed. Remove the above mentioned screws and the bezel with four bezel-glass-clamps may be removed. O To reinstall the T.V. bezel assembly, reverse this procedure.

T.V. BEZEL GLASS CLAMPS

Figure 2-11 Removing the T.V. Bezel - Upright

2-13

Page 24

2.6 T.V. BEZEL ASSEMBLY REMOVAL (Cont'd) MINI

2.6.2 MINI MODEL: (See Figure 2-12)

NOTE: In order to do this, the main-display-glass MUST be removed first. See the "Mini Model” procedure. OQ Remove the screws which secure the T.V. bezel assembly and lift it out.
NOTE: Use the hole in the center of the maindisplay-glass support to grasp it. Reverse this procedure to reinstall the T.V. bezel assembly.

Figure 2-12 Removal of T.V. Bezel Assembly

Page 25

2.6 T.V. BEZEL ASSEMBLY REMOVAL (Cont'd) COCKTAIL

2.6.3 COCKTAIL TABLE MODEL: (See Figure 2-13)

NOTE: In order to do this, the main-display-glass MUST be removed first. See “Cocktail Model” procedure.

O Loosen the screws which secure the T.V. bezel glass-clamps in place. Move the clamps to the side and the bezel glass may be removed. Remove the screws which secure the bezel assembly to the table top and the bezel with four bezel-glass-clamps may be removed. OD To reinstall the T.V. bezel assembly, simply reverse this procedure.

Figure 2-13 Removing the T.V. Bezel - Cocktail

Page 26

2.7. T.V. MONITOR REPLACEMENT

2.7.1 Upright Models 2.7.2 Mini Models 2.7.3 Upright Models

2-16

Page 27

2.7 T.V. MONITOR REPLACEMENT UPRIGHT

WARNING: High voltages may exist in any tele- REMOVE (4) vision unit, even with the power disconnected BOLTS Use EXTREME CAUTION and do not touch electrical parts or the T.V. yoke area with your hands or with metal objects held in your hands! \n addition, BE SURE TO USE HEAVY GLOVES when handling the monitor. You could cut your hands on the metal T.V. chassis without such protection.
DANGER: The TV. monitor DOES NOT contain an isolation transformer on its chassis (it is mounted instead on the floor of the cabinet). When servicing the monitor on a test bench, YOU MUST ISOLATE THE MONITOR FROM AC VOLTAGE WITH AN ISOLATION TRANSFORMER.

2.7.1. UPRIGHT MODEL: (See Figure 2-14) O Turn power off to the game. C1 Open the rear access door. 0 Completely disconnect the T.V. monitor from all its cabling. DON’T FORGET THE CHASSIS GROUND WIRE. Before removing the T.V. monitor, the maindisplay-glass and bezel MUST be removed. See above “Upright Model” procedure. With the removal of only four bolts, the T.V. monitor and its mounting channels will be loose. The monitor mounting channels slide on top of and against two metal guides mounted to the cabinet’s right and left sides. The monitor is removed by sliding it out the back of the cabinet. See Figure 2-14. O To reinstall the T.V. monitor, reverse this procedure. C After replacing the T.V. monitor, be sure to run the game Self-Test.

Figure 2-14 Removing the Monitor - Upright

2-17

Page 28

2.7 T.V. MONITOR REPLACEMENT (Cont'd) UPRIGHT

WARNING: High voltages may exist in any television unit, even with the power disconnected. Use EXTREME CAUTION and do not touch electrical parts or the T.V. yoke area with your hands or with metal objects held inyour hands! In addition, BE SURE TO USE HEAVY GLOVES when handling the monitor. You could cut your hands on the metal T.V. chassis without such protection.
DANGER: The T.V. monitor DOES NOT contain an isolation transformer on its chassis (it is mounted instead on the floor of the cabinet). When servicing the monitor on a test bench, YOU MUST ISOLATE THE MONITOR FROM AC VOLTAGE WITH AN ISOLATION TRANS- FORMER. REMOVE
  • BOLTS 2.7.1. UPRIGHT MODEL: (See Figure 2-15) (Cont'd) OQ Turn power off to the game.

O Open the rear access door. O Completely disconnect the T.V. monitor from all its cabling. DON'T FORGET THE CHASSIS GROUND WIRE. Before removing the T.V. monitor, the maindisplay-glass MUST be removed. See above “Upright Model” procedure. O With the removal of only four bolts, the T.V. monitor will be loose.

CAUTION: BE SURE to support the T.V. monitor from the rear while removing the four bolts so it will not fall out of the cabinet. Figure 2-15 Removing the Monitor - Upright O The monitor mounting channels slide on top of and against two metal guides mounted to the cabinet’s right and left sides. The monitor is removed by sliding it out the back of the cabinet. O To reinstall the T.V. monitor, reverse this procedure. O After replacing the T.V. monitor, be sure to run the game Self-Test.

2-18

Page 29

2.7 T.V. MONITOR REPLACEMENT (Cont'd) MINI

WARNING: High voltages may exist in any television unit, even with the power disconnected. Use EXTREME CAUTION and do not touch electrical parts or the T.V. yoke area with your hands or with metal objects held in your hands! In addition, BE SURE TO USE HEAVY GLOVES when handling the monitor. You could cut your hands on the metal T.V. chassis without such protection.
DANGER: The T.V. monitor DOES NOT contain an isolation transformer on its chassis (it is mounted instead on the floor of the cabinet). When servicing the monitor on a test bench, YOU MUST ISOLATE THE MONITOR FROM AC VOLTAGE WITH AN ISOLATION TRANS- FORMER. REMOVE
  • BOLTS

2.7.2 MINI MODEL: (See Figure 2-16) CG Turn the power off to the game.

Q Open the rear access door. Q Completely disconnect the T.V. monitor from all its cabling. _DON'T FORGET THE CHASSIS GROUND WIRE. Before removing the T.V. monitor, the maindisplay-glass and bezel MUST be removed. See above "Mini Model” procedure. With the removal of only four bolts, the T.V. monitor will be loose.

CAUTION: BE SURE to support the T.V. monitor from the rear while removing the four bolts so it will not fall out of the cabinet.

The monitor is removed by supporting it and pulling straight back as shown in Figure 2-16. O To reinstail the T.V. monitor, reverse this procedure. After replacing the T.V. monitor, be sure to run the game Self-Test. Figure 2-16 Removing the Monitor - Mini

2-19

Page 30

2.7. T.V. MONITOR REPLACEMENT (Cont'd) COCKTAIL

WARNING: High voltages may exist in any television unit, even with the power disconnected. Use EXTREME CAUTION and do not touch electrical parts or the T.V. yoke area with your hands or with metal objects held in your hands! In addition, BE SURE TO USE HEAVY GLOVES when handling the monitor. You could cut your hands on the metal T.V. chassis without such protection Once the latches are released, unhook them from their latch plates. Grasp the table top at "A" and open it as indicated in Figure 2-17.
CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet.

O Remove the screws which hoid the table top glass clamps in place.

DANGER: The T.V. monitor DOES NOT contain an isolation transformer on its chassis (it is Remove the table top glass. mounted instead on the floor of the cabinet). O Lift out the T.V. bezel assembly. See above When servicing the monitor on atest bench, YOU "Cocktail" procedure. MUST ISOLATE THE) MONITOR FROM AC: OD Completely disconnect the T.V. monitor from ail SORE WHT AN’ IGOLATION. TRANS: its cabling. DON'T FORGET THE CHASSIS GROUND WIRE. O Remove the screws holding the T.V. monitor 2.7.3. COCKTAIL TABLE MODEL: (See Figure chassis to the "L" by the door hinge(s). See 2-18) Figure 2-18. O Close the Cocktail Table and re-latch it. O Turn the power off to the game. ° ' oo in bi O Remove the screws which secure the T.V. monipen the coin box door and release the two tor mounting brackets to the edges of the slot latches indicated in Figure 2-17. cut in the table top. See Figure 2-18.

O Pry up the end of each monitor mounting

WARNING: The right hand latch i: ery Close to the HIGH VOLTAGE on the monitor. bracket with a screwdriver or similar tool until you can grasp them both.

Figure 2-17 Opening the Cocktail! Game

2-20

Page 31

2.7 T.V. MONITOR REPLACEMENT (Cont'd) COCKTAIL

Lift the T.V. monitor straight up and out of the table top being VERY CAREFUL notto bump the neck of the picture tube. To reinstall the T.V. monitor assembly, reverse this procedure. Be sure to check the clearance of the "L” brackets BEFORE setting the monitor into the table top. After replacing the T.V. monitor, be sure to run the game in Self-Test.

2-21 REMOVE 6 SCREWS (3 EACH SIDE) LIFT MONITOR STRAIGHT UP

a “NY REMOVE 4 SCREWS (2 EACH SIDE)

Figure 2-18 Removing the Monitor - Cocktail

Page 32

2.8 PRINTED CIRCUIT BOARD (P.C.B.) REPLACEMENT 2.8.1 Upright Models 2.8.2 Mini Models 2.8.3 Cocktail Models

2-22

Page 33

2.8 PRINTED CIRCUIT BOARD (P.C.B.) REPLACEMENT UPRIGHT

2.8.1. UPRIGHT MODEL: (See Figure 2-19) O Turn the power to the game off.

O Unlock and open the rear access door (game board) and the coin door (sound board).

QO Disconnect the game board from all its cabling. UO Disconnect the sound board fromallits cabling. C1 Remove the indicated P.C.B. supports and lift the above P.C.B.’s out of the cabinet. Disconnect the power supply board from all its cabling, remove the P.C.B. supports indicated in Figure 2-19, and slide it out the back of the cabinet. Q To reinstall the above P.C.B.’s, reverse this procedure.

NOTE: P.C.B.’s are all keyed and will ONLY fit into their connectors one way without forcing them. The plugs on the cable harness which connectit to the P.C.B.’s are also keyed and will ONLY go onto their connectors one way without forcing them.

CT L a Rea PELE EPMA NEM! site Saale

ad eae”

REMOVE REMOVE SUPPORT SUPPORT TO TO SLIDE SLIDE POWER GAME SUPPLY BOARD BOARD OUT OUT

Figure 2-19 Removing P.C.B.'s - Upright

2-23

Page 34

2.8 PRINTED CIRCUIT BOARD (P.C.B) REPLACEMENT (Cont'd) UPRIGHT

NOTE: P.C.B.'s are all keyed and will ONLY fit into O To remove the power supply PCB for the their connectors one way without forcing them. commercial card rack. See Figure 2-21. The plugs on the cable harness which connectit to . . . . the P.C.B.'s are also keyed and will ONLY go onto Disconnect it from all its cabling, remove the their connectors one way without forcing them. screws which secure the top PCB support to its mounting bracket (be carefu! not to lose the 2.81 UPRIGHT MODEL: (See Figure 2-21) washers), and lift it out.

(Cont'd) C To reinstall the above P.C.B.'s, reverse this

Turn the power to the game off. procedure.

O Unlock and open the coin door. O Reach inside and release the game’s front access door locking latches. See Figure 2-20 and the drawing on top of the coin box lid. Q Slide out the utility shelf. See Figure 2-21. Q Mounted on the utility shelf is the commercial card rack with six cards in it. O Mounted next to the commercial card rack is its power supply P.C.B. O To remove the cards from the commercial card rack, simply lift on their extractors and remove OPEN LOWER SERVICE DOOR BY RELEASING them. TWO. ACCESS CLAMPS. (Locations AS SHOWN) REMOVE TWO RED SHIPPING BRACKETS AND SLIDE OUT SERVICE SHELF. wesi0900-0000 A ‘| N H S|

he EY Be

NOTE: BEFORE removing the "GAME PCB", be| sure to disconnect it from all its cabling. Figure 2-20 Opening the Front Access Door - Upright

REMOVE THIS BRACKET TO TAKE OUT POWER SUPPLY BOARD

LIFT UP ON EXTRACTORS TO REMOVE CARDS FROM CARD BACK

Figure 2-21 Removing Printed Circuit Boards - Upright

2-24

Page 35

2.8 PRINTED CIRCUIT BOARD (P.C.B.) REPLACEMENT (Cont'd) MINI

2.8.2 MINI MODEL: (See Figure 2-22) O Turn the power off to the game.

Unlock and open the rear access door. O Disconnect the game board from all its cabling. Disconnect the sound board from allits cabling. Oo Remove the indicated P.C.B. supports and lift the above P.C.B.'s out of the cabinet. O Disconnect the power supply board from its cabling, remove the P.C.B. supports indicated in Figure 2-22 and slide it out the back of the cabinet. O To reinstall the above P.C.B.'s, reverse this : procedure.

REMOVE P.C.B. LIFT UP ON SUPPORT AND EXTRACTORS TO SLIDE BOARD REMOVE CARDS OuT FROM BACK

Figure 2-22 Removing P.C.B.'s - Mini

2-25

Page 36

2.8 PRINTED CIRCUIT BOARD (P.C.B.) REPLACEMENT (Cont'd) MINI

2.8.2. MINI MODEL: (See Figure 2-23) (Cont'd) O Turn the power off to the game.

© Unlock and open the rear access door.

O Disconnect the "GAME PCB” from all its cabling. O To remove any of the PCB's from the commercial card rack, just lift up on their extractors and slide them up and out. They may now be removed from the cabinet. O Disconnect the power supply board from all its cabling, remove the P.C.B. supports indicated in Figure 2-23, and slide it out the back of the cabinet.

To reinstall the above P.C.B.’s reverse this procedure.

REMOVE P.C.B. LIFT UP ON SUPPORT AND EXTRACTORS TO SLIDE BOARD OUT REMOVE CARDS FROM BACK

Figure 2-23 Removing Printed Circuit Boards - Mini

2-26

Page 37

2.8 PRINTED CIRCUIT BOARD (P.C.B.) REPLACEMENT (Cont'd) COCKTAIL SS

2.8.3 COCKTAIL TABLE MODEL: (See Figure 2-24) O Turn the power off to the game.

O Open the cabinet. Open the coin box door and release the two latches indicated in Figure 2-17.

WARNING: T the HIGH VO! ight hand latch is very close to GE on the monitor.

Once they’re released, unhook them from their latch plates. O Grasp the table top at ”A” and open it as indicated in Figure 2-17.

CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet.

REMOVE SUPPORT TO SLIDE GAME BOARD OUT a To remove the power supply board. See Figure 2-24, Disconnect it from all its cabling. Remove the two smallest P.C.B. supports. Once these are removed, the power supply can be lifted out the top of the cabinet. To reinstall the power supply board, reverse this procedure. To remove the game and sound boards. See Figure 2-24. Disconnect the game board from all its cabling. Disconnect the sound board from allits cabling.

Remove the indicated P.C.B. supports and lift the above P.C.B.’s out of the cabinet. To reinstail the game and sound boards, reverse this procedure.

REMOVE SUPPORT TO SLIDE POWER SUPPLY BOARD FROM CABINET

Figure 2-24 Removing P.C.B's - Cocktail

2-27

Page 38

2.8 PRINTED CIRCUIT BOARD (P.C.B.) REPLACEMENT (Cont'd) COCKTAIL

2.8.3 COCKTAIL TABLE MODEL: (See Figure 2-25) (Cont'd) Turn the power off to the game. Q Open the cabinet: Open the coin box door and release the two latches indicated in Figure 2-17.

WARNING: The right hand latch is very close to the HIGH VOLTAGE on the monitor. BE CAREFUL!!

Once they're released, unhook them from their latch plates. O Grasp the table top at "A" and open it as indicated in Figure 2-17.

CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet. QO

o To remove the power supply board. See Figure 2-25. Disconnect it from all its cabling. Remove the two smallest P.C.B. supports. Once these are removed, the power supply can be lifted out the top of the cabinet. To reinstall the power supply board, reverse this procedure.

To remove the PCB's from the commercial card rack. See Figure 2-25. Disconnect the "GAME PCB” from all its cabling. To remove any of the PCB’s from the commercial card rack, just lift up on their extractors and slide them up and out. They may now be removed from the cabinet.

To reinstall these PCB's, reverse this procedure.

LIFT UP ON EXTRACTORS TO © REMOVE CARDS) FROM RACK REMOVE P.C.B. SUPPORT LOCATED ON THIS SIDE AND SLIDE BOARD UP

Figure 2-25 Removing Printed Circuit Boards - Cocktail

2-28

Page 39

2.9 OPENING THE UPPER ATTRACTION PANEL

2.9.1 Upright Models 2.9.2 Mini Models (THE COCKTAIL MODEL HAS NO BACK—LIT ATTRAC—

TION PANEL)

2-29

Page 40

2.9 OPENING THE ATTRACTION PANEL UPRIGHT

2.9.1 UPRIGHT MODEL: (See Figure 2-26) REMOVE TOP BRKT. © Turn the power to the game off. & SLIDE HEADER UP O Opening the attraction panel: Remove the screws which secure the top bracket in place. (They are on its top side.) See + f_, Figure 2-26. Remove the top bracket and slide up the attraction panel. This exposes the attraction panel fluorescent light tube and its mounting bracket assembly. O To reinstall the attraction panel, reverse this procedure.

Figure 2-26 Opening the Attraction Panel - Upright

2-30

Page 41

2.9 OPENING THE ATTRACTION PANEL (Cont'd) UPRIGHT

2.9.1 UPRIGHT MODEL: (See Figure 2-27) (Cont'd) O Turn the power to the game off.

O Opening the attraction panel: Remove the screws which secure the bottom bracket in place. (They are on its bottom side.) See Figure 2-27. Remove the lower bracket and slide down the attraction panel. This exposes the attraction panel fluorescent light tube and its mounting bracket assembly. O To reinstall the attraction panel, reverse this procedure.

SLIDE ATTRACTION REMOVE BOTTOM PANEL DOWN BRACKET

Figure 2-27 Opening the Attraction Panel

  • Upright

2-31

Page 42

2.9 OPENING THE ATTRACTION PANEL (Cont'd) UPRIGHT

2.9.1 UPRIGHT MODEL: (See Figure 2-28) (Cont'd) O Turn the power to the game off. REMOVE TOP SLIDE ATTRACTION BRACKET PANEL UP O Opening the attraction panel: Remove the screws which secure the top bracket in place. (They are on its top side.) See Figure 2-28, Remove the top bracket and slide up the attraction panel. This exposes the attraction panel fluorescent light tube and its mounting bracket assembly. QO To reinstall the attraction panel, reverse this procedure.

Figure 2-28 Opening the Attraction Panel

  • Upright

2-32

Page 43

2.9 OPENING THE ATTRACTION PANEL (Cont'd) MINI

2.9.2 MINI MODEL: (See Figure 2-29) o

oO

o Turn the power off to the game. Remove the screws which secure the top bracket in place. (They are on its top side.) Remove the top bracket and slide up the attraction panel. This exposes the attraction panel light bulbs and their mounting board. To reinstall the attraction panel, reverse this procedure.

2-33 REMOVE TOP BRKT. & SLIDE HEADER UP

Figure 2-29 Opening the Attraction Panel - Mini

Page 44

2.9 OPENING THE ATTRACTION PANEL MINI

2.9.2 MINI MODEL: (See Figure 2-30) (Cont'd) O Turn the power off to the game. Remove the screws from the top and bottom of the formed attraction panel. 0 Remove the formed attraction panel by pulling it straight away from the cabinet. This exposes the attraction panel light bulbs and their mounting board. O To reinstall the attraction panel, reverse this procedure.

Figure 2-30 Removing the Attraction Panel - Mini

2-34

Page 45

REPLACING THE GAMES UPPER ATTRACTION PANEL LIGHTING

2.10.1 Upright Models 2.10.2 Mini Models (THE COCKTAIL MODELS HAVE NO BACK-LIT

ATTRACTION PANEL)

2-35

Page 46

2.10 SERVICING ATTRACTION PANEL LIGHTING UPRIGHT

2.10.1 UPRIGHT MODEL: 0 Turn the power to the game off.

NOTE: in order to do this, the attraction panel MUST be removed first. See “Upright Model” procedure.

QO The fluorescent light tube may be replaced at this time. BE CAREFUL NOT TO DROP IT.

WARNING: If you drop a fluorescent tube and it breaks, IT WILL IMPLODE! Shattered glass can fly six (6) feet or more from the implosion. Use care when replacing any fluorescent tube.

O Replacing the fluorescent light tube starter. See Figure 2-31. Be sure the power to the game has been turned off. Grasp the starter (it is on the back of the mounting bracket), give it a quarter turn, and remove it from its socket.

Q To replace the fluorescent light tube starter, reverse this procedure.

Q Replacement of the fluorescent tube mounting bracket assembly. See Figure 2-32. Be sure the power is off to the game. Disconnect it from its power cable. REMOVE SCREWS TO LIGHT BRKT.

Figure 2-32 Replacing Fluorescent Light Mounting Bracket - Upright Remove the screws which secure it and gently slide it out the front of the cabinet, being careful not to catch its power cable on anything. 1 To reinstall the fluorescent tube mounting bracket assembly, reverse this procedure.

1/4 TURN TO REPLACE FLUORESCENT TUBE STARTER

Figure 2-31 Replacing Fluorescent Tube Starter

Page 47

2.10 SERVICING ATTRACTION PANEL LIGHTING (Cont'd) UPRIGHT

2.10.1 UPRIGHT MODEL: (Cont'd) O Turn the power to the game off.

NOTE: In order to do this, the attraction panel MUST be removed first. See “Upright Model” procedure, O The fluorescent light tube may be replaced at this time. BE CAREFUL NOT TO DROP IT.
WARNING: If you drop a fluorescent tube and it breaks, IT WILL IMPLODE! Shattered glass can Disconnect the light board assembly from all its cabling. There is one plug at the upper right and upper left corners of the rear of the cabinet. There is also a small plug right at the ON/OFF switch. And DO NOT FORGET TO DISCON— NECT THE GROUND WIRE LUG FROM THE ON/OFF SWITCH! Remove the screws which secure the light board assembly to the cabinet. The light board assembly is now free and can be slid out through the hole in the front of the game fly six (6) feet or more from the implosion. Use where the attraction panel was mounted. care when replacing any fluorescent tube. O To reinstall the light board assembly, reverse this procedure. O Replacement of the fluorescent and ultraviolet O Replacing the fluorescent light tube starter, See Figure 2-34. tube mounting bracket assemblies. Be sure the power to the game has been turned . . . off. Disconnect it from its power cable. Grasp the starter (it is on the back of the Remove une screws which secure them to the mounting bracket), give it a quarter turn, and speaker board assembly. remove it from its socket. QO To reinstall the fluorescent ultraviolet tube 0 To replace the fluorescent light tube starter, mounting bracket assemblies, reverse this reverse this procedure. Procedure.

O The ultraviolet light tube may be replaced at this time by removing the rear access door of the game and the back scenery panel if necessary. See Figure 2-35. BE CAREFUL NOT TO DROP IT.

WARNING: If you drop an ultraviolet light tube and it breaks, 1T WILL IMPLODE! Shattered glass can fly six (6) feet or more from the implosion. Use care when replacing any ultraviolet tube.

SPEAKER BOARD QO Replacing the ultraviolet light tube starter. See Figure 2-34. Be sure the power to the game has been turned off. Grasp the starter (it is on the back of the mounting bracket), give it a quarter turn, and remove it from its socket. OQ To replace the ultraviolet light tube starter, reverse this procedure. O Removing the light board assembly: See Figure 2-33 The attraction panel, the rear access door of the game, and, if necessary, the back scenery panel MUST be removed first. This will enable you to reach all the necessary areas where cables MUST be disconnected. Figure 2-33 Servicing Attraction Panel Lighting ~ Upright

2-37

Page 48

2.10 SERVICING ATTRACTION PANEL LIGHTING (Cont'd) UPRIGHT

‘% TURN TO REPLACE

FLUORESCENT TUBE STARTER

Figure 2-34 Replacing Fluorescent Tube Starter

BLACK LIGHT CAN BE REACHED THROUGH HERE

2-38

Page 49

2.10 SERVICING ATTRACTION PANEL LIGHTING (Cont'd) MINI

2.10.2 MINI MODEL: (See Figure 2-36) O Turn the power off to the game. MOUNTING BOARD

NOTE: In order to do this, the attraction panel MUST be removed first. See “Mini Model” procedure. O To service the light bulbs and their mounting board:

Turn the power to the game back on so you can see which bulbs are burnt out.

Mark the burnt out bulbs and turn the power to the game back off again. To replace the burnt out bulbs, grasp them gently and pull straight out. The new bulbs are gently pushed into the empty sockets. O To completely replace the light bulb mounting board: Open the cabinet rear access door and unplug the mounting board from its power cable. Remove the screws that hold the mounting board to the cabinet. Gently slide the mounting board out the front of the cabinet being careful not to catch its cable on anything. Figure 2-36 Servicing Attraction Panel Lighting O To reinstall the above removed items, reverse this procedure.

2-39

Page 50

SPEAKER REPLACEMENT

2.11.1 Upright Models 2.11.2 Mini Models

2.11.3 Cocktail Models

2-40

Page 51

2.11. SPEAKER REPLACEMENT UPRIGHT

2.11.1. UPRIGHT MODEL: (See Figure 2-37) Q Turn the power to the game off.

NOTE: In order to do this, the attraction panel and fluorescent light fixture MUST be removed first. See “Upright Model” procedure.

C1 Replacing the speaker. Be sure the power is off to the game. Remove the attraction panel and disconnect the speaker from its cabling. Remove the nuts and bolts which secure the speaker and speaker grill in place and set them and the speaker grill aside. Once the bolts which secure the speaker in place are removed, the speaker may be removed through the opening where the attraction panel was.

O Reverse this procedure to reinstall the speaker.

2-41 REMOVE SCREWS TO LIGHT BRKT.

REMOVE SPEAKER FROM FRONT OF GAME

Figure 2-37 Speaker Replacement

Page 52

2.11. SPEAKER REPLACEMENT (Cont'd) UPRIGHT

2.11.1. UPRIGHT MODEL: (See Figure 2-38) (Cont'd)

NOTE: In order to do this, the attraction panel MUST be removed first. See "Upright Model” procedure.

O Replacing the speaker. O Be sure the power is off to the game.

Remove the attraction panel and disconnect the speaker from its cabling. Remove the nuts and bolts which secure the speaker and speaker grill in place and set them and the speaker grill aside. Once the bolts which secure the speaker in place are removed, the speaker may be removed through the opening where the attraction panel was. Cl Reverse this procedure to reinstall the speaker.

MOUNTING HARDWARE SPEAKER GRILL

Figure 2-38 Speaker Replacement

2-42

Page 53

2.11 SPEAKER REPLACEMENT (Cont'd) UPRIGHT

2.11.1 UPRIGHT MODEL: (Cont'd) O To replace the speaker. Be sure the power is off to the game.

Disconnect the speaker from its cabling. Remove the nuts and bolts securing the speaker, Slide the speaker out through the rear access door. 1 To reinstall the speaker, simply reverse this procedure. MOUNTING HARDWARE

SPEAKER MOUNTING SPEAKER GRILL HARDWARE

Figure 2-39 Speaker Location - Upright

Figure 2-40 Rear View - Speaker Location - Upright

2-43

Page 54

2.11 SPEAKER REPLACEMENT (Cont'd ) UPRIGHT

2.11.1. UPRIGHT MODEL: (Cont'd) O Turn the power to the game off.

NOTE: In order to do this, the attraction panel MUST be removed first. See "Upright Model” Procedure.

O Removing the speaker board assembly: The attraction panel, the rear access door ofthe game, and if necessary, the back scenery panel MUST be removed first. This will enable you to reach all the necessary areas where cables MUST be disconnected. Disconnect the speaker board assembly from all its cabling. There is one plug at the upper right and upper left corners of the rear of the cabinet. There is also a small plug right at the ON/OFF switch. And DO NOT FORGET TO DISCON- NECT THE GROUND WIRE LUG FROM THE ON/OFF SWITCH!

SPEAKER BOARD

Figure 2-41 Speaker Replacement - Upright

2-44 Remove the screws which secure the speaker board assembly to the cabinet. The speaker board assembly is now free and can be slid out through the hole in the front of the game where the attraction panel was mounted.

QO Replacing the speaker(s). Disconnect the speaker(s) from its cabling. Remove the nuts and bolts which secure the speaker in place and set them aside. Once the bolts which secure the speaker(s) in place are removed, the speaker(s) may be removed from the speaker board assembly. O Reverse this procedure reinstall speaker(s). to the

QO Toreinstall the speaker board assembly, reverse this procedure.

MOUNTING HARDWARE

SPEAKER

Figure 2-42 Speaker Replacement - Upright

Page 55

2.11. SPEAKER REPLACEMENT (Cont'd) MINI

2.11.2 MINI MODEL: (See Figure 2-43) REMOVE O To replace the speaker. SPEAKER

Be sure the power is off to the game. mee

Disconnect the speaker from its cabling. Remove the nuts and bolts securing the speaker. Slide the speaker out through the rear access door. O To reinstall the speaker, simply reverse this procedure.

Figure 2-43 Speaker Removal - Mini

2-45

Page 56

2.11. SPEAKER REPLACEMENT (Cont'd) COCKTAIL

Figure 2-44 Opening the Cocktail Game

2.11.3 COCKTAIL TABLE MODEL:

QO Turn power to the game off. O Open the coin box door and release the two latches indicated in Figure 2-44,

WARNING: The right hand latch is very close to the HIGH VOLTAGE on the monit

Once they’re released, unhook them from their latch plates. O Grasp the table top at "A” and open it as indicated in Figure 2-44.

CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet.

O To replace the speaker. Be sure the power is off to the game. Disconnect the speaker from its cabling. Remove the nuts and bolts securing the speaker. Lift the speaker out. SPEAKERS O To reinstall the speaker, simply reverse this Procedure. Figure 2-45 Speaker Replacement - Cocktail

2-46

Page 57

2.12 OPENING THE LOWER ATTRACTION PANEL AND

SERVICING IT’S LIGHTING ASSEMBLY

2.12.1 Upright Models (THE MINI AND COCKTAIL MODELS HAVE NO BACK-

LIT LOWER ATTRACTION PANELS)

2-47

Page 58

2.12 OPENING THE LOWER ATTRACTION PANEL AND SERVICING ITS LIGHTING ASSEMBLY UPRIGHT

2.12.1. UPRIGHT MODEL ONLY Q Be sure the power is off to the game.

O Remove the contro! panel as described previously. This exposes the attraction panel fluorescent light tube and its mounting bracket assembly. See Figure 2-46. The fluorescent light tube may be replaced at Q Be sure the power is off to the game. Q Disconnect it from its power cable.

NOTE: The fluorescent tube mounting bracket is an integral part of the center attraction panel assembly and cannot be replaced unless the center attraction panel assembly is removed from this time by reaching through the space where the contro] panel was before you removed it. the game cabinet.

r QO Remove the screws from top support bracket

WARNING: If you drop a fluorescent tube and it and the screws along its Base whith eccure the breaks, IT WILL IMPLODE! Shattered glass can mounting bracket and the center attraction fly six (6) feet or more from the implosion. Use panel assembly to the cabinet as shown in care when replacing any fluorescent tube. Figure 2-46. QO Replacing the fluorescent tube starter. See Q Thecenter attraction panel assembly is now free Figure 2-47. and can be rotated forward and lifted out of the Grasp the starter (it is on the back of the cabinet. mounting bracket), give it a quarter turn, and = _ The screws which secure the fluorescent tube remove it from its socket. mounting bracket to the center attraction panel To replace the fluorescent light tube starter, are now accessible so it can be separated from reverse this procedure. the center attraction panel and replaced. O Replacement of the fluorescent tube mounting © To reinstall any of the above removed items, bracket assembly. See Figure 2-46.

1/4 TURN TO REPLACE reverse this procedure.

FLUORESCENT LIGHT TUBE

REMOVE SCREWS TO TAKE CENTER ATTRACTION PANEL FROM GAME

FLUORESCENT TUBE STARTER

Figure 2-47 Replacing the Fluorescent Tube Starter - Upright

2-48

Page 59

2.13 SERVICING THE CONTROL PANEL LIGHTING

ASSEMBLY

2.13.1 Upright Models (THE MINI AND COCKTAIL MODELS HAVE NO

CONTROL PANEL LIGHTING ASSEMBLIES)

2-49

Page 60

2.13 SERVICING THE CONTROL PANEL LIGHTING ASSEMBLY UPRIGHT

2.13.1. UPRIGHT MODEL ONLY O Be sure the power is off to the game.

O Remove the control panel as described previously. This exposes the bottom row of screws which secure the control panel support bracket and the black light protector in place. See Figure 2-48, O Remove all the screws which secure the above items in place and set them aside. The black light tube may be replaced at this time by reaching through the space where the light protector was before you removed. it.

WARNING: If you drop a fluorescent tube and it breaks, IT WILL IMPLODE! Shattered glass can tly six (6) feet or more from the implosion. Use care when replacing any fluorescent tube.

O Replacing the black light tube starter. See Figure 2-47. Remove the black light tube. Remove the screws which secure the black light tube mounting bracket to the cabinet. See Figure 2-49. The mounting bracket is now loose and can be pulled out and slightly to one side until you can see the black light tube starter.

REMOVE THESE SCREWS O Grasp the starter (it is on the back of the mounting bracket), give it a quarter turn, and remove it from its socket.

To replace the black light tube starter, reverse this procedure. O The black light tube mounting bracket assembly may be replaced at this time by simply disconnecting it from its power cable and removing it from the game. O To reinstall any of the above mentioned items, simply reverse this procedure.

Figure 2-49 Replacing the Fluorescent Tube Starter - Upright

~ BLACK LIGHT PROTECTOR

CONTROL PANEL SUPPORT BRKT.

Figure 2-48 Servicing Control Panel Lighting Assembly - Upright

2-50

Page 61

2.13 SERVICING THE CONTROL PANEL LIGHTING ASSEMBLY UPRIGHT

1/4 TURN FLUORESCENT TUBE TO REPLACE STARTER

Figure 2-50 Replacing the Fluorescent Tube Starter - Upright

2-51

Page 62

SERVICING AUXILIARY LIGHTING

2.14.1 Upright Models - Servicing Windshield Fluorescent Light 2.14.2 Upright Models - Servicing The Black Light Above Control Console 2.14.3 Upright Models - Servicing The Fluorescent Light Behind The Front Service Panel

2-52

Page 63

2.14 SERVICING AUXILIARY LIGHTING

2.14.1. UPRIGHT MODEL: Servicing Windshield Fluorescent Light

Be sure the power is off to the game.

Remove the upper rear access door. This exposes the windshield fluorescent light tube mounting bracket assembly. See Figure 2-51. Replacing the fluorescent tube starter. Figure 2-51. Grasp the starter (it is on the back of the mounting bracket), give it a quarter turn, and remove it from its socket. To replace the fluorescent light tube starter, reverse this procedure. See

Removal of the fluorescent tube mounting bracket assembly from the cabinet. Be sure the power is off to the game. Disconnect it from its power cable.

FLUORESCENT LIGHT TUBE MTG. BRKT.

STARTER UPRIGHT

Remove the screws along its base which secure the mounting bracket to the inside of the cabinet as shown in Figure 2-51. Remove the two end screws first and the center one last. The fluorescent tube mounting bracket assembly is now free and can be removed from the cabinet.

The fluorescent light tube may be easily replaced at this time.

WARNING: If you drop a fluorescent tube and it breaks, IT WILL IMPLODE! Shattered glass can fly six (6) feet or more from the implosion. Use care when replacing any fluorescent tube.

To reinstall any of the above removed items, reverse this procedure.

REMOVE (3) SCREWS

Figure 2-51 Servicing Windshield Fluorescent Light - Upright

2-53

Page 64

2.14 SERVICING AUXILIARY LIGHTING (Cont'd) UPRIGHT

2.14.2 UPRIGHT MODEL: Servicing The Black Light Above Control Console

QO Turn the power to the game off and remove the screws which secure the glass clamping plate in position. See Figure 2-52. Lift out the glass clamping plate. Remove the screws which secure the bottom of the black light shield to the front service panel. Be sure you support the black light shield as you remove these screws so it will not fall on the floor. The black light tube may be replaced at this time. BE CAREFUL NOT TO DROP IT.

WARNING: If you drop a black light tube and it breaks, IT WILL IMPLODE! Shattered glass can fly six (6) feet or more from the implosion. Use care when replacing any black light tube.

O To reinstall the black light shield, reverse this Procedure. Q Replacing the black light tube starter. See Figure 2-53.

NOTE: The main-display-glass MUST be removed in order to do this. See “Upright Model” procedure. GLass CLAMPING PLATE

Figure 2-52 Removing Glass Clamping Plate

QO Be sure the power to the game has been turned off. Grasp the starter (it is on the back of the mounting bracket, just inside the frame for the maindisplay-glass), give it a quarter turn, and remove it from its socket. 1 To replace the black light tube starter, reverse this procedure,

ATM

1/4 TURN TO REPLACE FLUORESCENT TUBE STARTER

Figure 2-53 Replacing the Fluorescent Tube Starter - Upright

2-54

Page 65

2.14 SERVICING AUXILIARY LIGHTING (Cont'd) UPRIGHT

2.14.3. UPRIGHT MODEL: Servicing The Fluorescent Light Behind The Front Service Panel

O Remove the front service panel.

O Turn the power to the game off.

NOTE: In order to do this, the following items MUST be removed first, in this order, to make room: 1) the main-display-glass glass clamping plate; 2) the black light shield; and 3) the control panel. See the appropriate sections of this manual for removal instructions.

C Remove the screws at the top of the front service panel which secure it to the cabinet. O Tilt it back to clear the black light and lift it up and out as shown in Figure 2-54. O To reinstall the front service panel, reverse this procedure. OD The fluorescent light tube may be replaced at this time. BE CAREFUL NOT TO DROP IT!

WARNING: If you drop a fluorescent tube and it breaks, IT WILL IMPLODE! Shattered glass can fly six (6) feet or more from the implosion. Use care when replacing any fluorescent tube.

QO Replacing the fluorescent light tube starter. See Figure 2-55. U Be sure the power to the game has been turned off. FRONT SERVICE PANEL

Figure 2-54 Removing the Front Service Panel

  • Upright

QO Grasp the starter (it is on the back of the mounting bracket), give it a quarter turn, and remove it from its socket.

To replace the fluorescent light tube starter, reverse this procedure.

a

1/4 TURN TO REPLACE FLUORESCENT TUBE STARTER

Figure 2-55 Replacing the Fluorescent Tube Starter - Upright

2-55

Page 66

lll. Technical Troubleshooting

Introduction

The most common problems occur in harness components such as the coin acceptor, player controls, interconnecting wiring, etc. The TV monitor and PCB computer cause their share of problems too, but not as much as the harness and its component parts, TV monitor troubleshooting will not be covered here because it is covered in that section of this manual. As you already know, the PCB computer is a complex device with a number of different circuits. Some circuits remain basically the same among games, but overall there are agreat many differences between them. PCB troubleshooting procedures, therefore, can be lengthy and will differ greatly among games. However, some basic Z-80 CPU information is involved in this section.

General Suggestions

The first step in any troubleshooting procedure is correctly identifying the malfunction’s symptoms. This includes not only the circuits or features malfunctioning, but also those still operational. A carefully trained eye will pick up other clues as well. For instance, a game in which the computer functions fail completely just after money was collected may have a quarter shorting the PCB traces. Often, an experienced troubleshooter will be able to spot the cause of the problem even before opening the cabinet. After all the clues are carefully considered, the possible malfunctioning areas can be narrowed down to one or two good suspects. Those areas can be examined by a process of eiimination until the cause of the malfunction is discovered.

Harness Component Troubleshooting

Typical problems falling in this category are coin and credit problems, power problems and failure of individual features. NO GAME CREDIT For example, your prospective player inserts his quarter and is not awarded a game. The first item to check is if the quarter is returned. If the quarter is returned, the malfunction most certainly lies in the coin acceptor itself. First, use a set of test coins (both old and new) to ascertain that the player's coin is not undersize or underweight. If your test coins are also returned, coin acceptor servicing is indicated. Generally, the cause of this particular problem is a maladjusted magnet gate. Normally, this will mean slightly closing the magnet gate alittle by turning the adjusting screw out a bit (see section on coin acceptor for more deiails). lf the quarter is not returned and there is no game credit, the cause of the malfunction may be in one of several areas. First try operating the coin return button; if the coin is returned, the problem is most likely in the magnet gate. Enlarge the gap according to the coin acceptor service procedures. If this does not cure the problem, remove the coin acceptor, clean it and perform the major adjustment procedure. If the trapped coin is not returned when the wiper lever is actuated, you may have an acceptor jammed by a slug, gummed up with beer, a jammed coin chute, or mechanical failure of the acceptor mechanism. In this case, first check for the slug that will generally be trapped against the magnet. If so, simply remove the slug and test the acceptor. If the chute is blocked, remove the acceptor and remove the jammed coins. If there is actual failure of the acceptor, remove the unit and repair as indicated in the coin acceptor service procedures. lf the coin is making its way through the acceptor (that is, falling into the coin box), yet there is still no game credit, you either have a mechanical failure of the coin switch or electrical failure of the coin and credit circuits. The first place to begin is by checking the coin switch. Most of these switches are the make/break variety of micro switch, which is checked by testing for continuity between the NO, NC, and C terminals. When not actuated, the NC and C terminals should be continuous and the NO terminal open. When operated, the NO and C terminals should close and the NC should be open. If the coin switch checks out, examine the connections to the terminals to make sure there is good contact. If necessary, use the continuity tester and check from the terminal lug on the switch to the associated PCB trace. This will tell you if there is a continuous line all the way to the credit circuit.

Page 67

If the coin switch wires do not check out, the problem is in the computer — most likely in the coin and credit circuitry. If you do get game credit when a coin is deposited, but the game will not start when the start switch is pressed, you may have a problem in the start switch, the interconnecting wiring or in the computer. First check the switch. If the switch is OK, proceed to check the wiring. Again, make sure you go from the terminal lug on the switch to the PCB trace. This way, you will check the terminal contact as well as PCB edge connector contact. If the wiring is continuous, proceed to check the PCB credit circuit. If not, check each section of the wiring, until the discontinuity is located. !f the wiring is OK, the problem must lie in the computer.

Transformer and Line Voltage Problems

Your machine must have the correct line voltage to operate properly. If the line voltage drops too low, a circuit in the computer will disable game credit. The point at which the computer will fail to work will vary some from game to game, but no game will work on line voltage that drops below 105 VAC. Low line voltage may have many causes. Line voltage normally fluctuates a certain amount during the day as the total usage varies. Peak usage times occur mainly at dawn or dusk, so if your machine’s malfunction seems to be related to the time of day, this may be a factor. A large load connected to the same line as the game (such as a large air conditioner or other device with an exceptionally large motor) may drop the line voltage significantly when starting up. This drop can result in an intermittent credit problem. In addition, poor connections in the location wiring, plug, or line cord may also cause a significant drop in power. Cold solder joints in the game's harness, especially in areas like the transformer connections, interlock switch, or fuse block, may also produce the same results, although probably on a more permanent basis. Sometimes location owners (especially in bars) replace light switches with dimmer rheostats, and the game is sometimes on the same line. Obviously, the voltage available to the game is going to drop dramatically when the dimmer is turned. In any case, the way to check for correct line voltage is with your VOM. Set the VOM to 250 VAC and stick the probes in the wall receptacle. If it's OK here, check the transformer primary connections. If you do not get 117 VAC, examine the solder joints on the transformer, fuse block, and interlock switch. If you do get 117 VAC, the problem must be either in the transformer, harness connections, or in the PCB power supply. If you suspect the transformer, check its secondaries with the VOM set to 50 VAC and correlate the readings with the legend on the side of the transformer. The transformer must also be correctly grounded, so check the ground potential as well, especially if there is a hum bar rolling up or down the TV screen.

HARNESS PROBLEMS Other harness problems include blowing fuses and malfunctioning controls. The repeating blown-fuse problem can sometimes be quite exasperating to solve, for short circuits have the tendencyto occurin areas almost impossible to find. First, try inserting a new fuse, as old fuses age and blow without cause. If the new one also blows, you definitely have a short. The best way to approach this problem is by turning the power off and disconnecting devices that may be causing the problem, such as the TV, transformer, and PCB. Disconnect the devices by pulling off their connectors, but do not allow them to touch. If necessary, insulate them with small pieces of electrical tape. Then, connect your VOM across the terminals of the fuse block (all electrical power shut off), and set it to one of the resistance scales. This will save blowing a fuse each time you want to check the circuit. If the VOM reveals that disconnecting the devices removed the short, reconnect the devices one by one until the short returns. The last device connected is the one that is at fault. If the VOM reads a short even after the devices are disconnected, the fault must lie in the harness itself, and only patient exploration will reveal its location. First, carefully examine all the wiring, looking for terminals that may be touching, metal objects such as coins shorting connections or burned insulation. If necessary, use the VOM to check each suspected wire. MALFUNCTIONING CONTROLS One of the most common problems here is a bad potentiometer. Typically, a bad pot will cause the image to jump as it reaches a certain point. The only cure for this one is to install a new pot. If a feature that is operated by a switch (for example, joysticks, foot pedals, control panel buttons) does not operate at all, check the switch with a VOM or continuity tester to verify its operation. If the switch does not check out, replace it. If the switch is OK, you should suspect the input to the switch from the PCB. In this case, get out the harness and logic schematics and check to see what kind of input it is. In many cases, the input will be +5 VDC. Ifso, use the VOM to check its presence. Normally, the switch is used to pull a +5 VDC line LOW to GND or to pulla LOW line HIGH. If the PCB output is missing, check the wire length from the PCB. If you find the signal at the PCB trace, the wire length or connection is at fault. If not, begin exploring the PCB using the logic schematics.

Page 68

A Glossary of Microprocessor Terms

MICROPROCESSOR — one or several microcircuits that perform the function of a computer's CPU. Sections of the circuit have arithmetic and comparative functions that perform computations and executive instructions. CPU — central-processing unit. A computing system’s “brain”, whose arithmetic, control and logic elements direct functions and perform computations. The microprocessor section of a microcomputer is on one chip or several chips.

PROM — programmable read-only memory. User permanenily sets binary on-off bits in each cell by selectively fusing or not fusing electrical links. Nonerasable. Used for low-volume applications.

EPROM — erasable, programmable, read-only memory. Can be erased by ultraviolet light bath, then reprogrammed. Frequently used during design and development to get programs debugged, then replaced by ROM for mass production.

ROM — read-only memory. The program, or binary on-off bit pattern, is set into ROM during manufacture, usually as part of the last metal layer put onto the chip. Nonerasable. Typical ROM’s contain up to 16,000 bits of data to serve as the microprocessor’s basic instructions. RAM — random-access memory, Stores binary bits as electrical charges in transistor memory cells. Can be read or modified through the CPU. Stores input instructions and results. Erased when power is turned off. LSI — large scale integration. Formation of hundreds or thousands of so-called gate circuits on semiconductor chips. Very large scale integration (VLS) involves microcircuits with the greatest component density. MOS — metal-oxide semiconductor. A layered construction technique for integrated circuits that achieves high component densities. Variations in MOS chip structures create circuits with speed and low-power requirements, or other advantages (static will damage a MOS chip).

Introduction to the

Z-80 CPU

The term “microcomputer” has been used to describe virtually every type of small computing device designed within the last few years. This term has been applied to everything from simple “microprogrammed” controllers constructed out of TTL MSI up to low end minicomputers with a portion of the CPU constructed out of TTL LSI “bit slices.” However, the major impact of the LSI technology within the last few years has been with MOS LSI. With this technology, it is possible to fabricate complete and very powerful computer systems with only a few MOS LSI components. The Zilog Z-80 family of components can be configured with any type of standard semiconductor memory to generate computer systems with an extremely wide range of capabilities. For example, as few as two LSI circuits and three standard TTL MS! packages can be combined to form a simple controller. With additional memory and I/O devicesa computer can be constructed with capabilities that only a minicomputer could previously deliver. New products using the MOS LSI microcomputer are being developed at an extraordinary rate. The Zilog Z-80 component set has been designed to fit into this market through the following factors:

  • The Z-80 is fully software compatible with the popular 8080A CPU. Existing designs can be easily converted to include the Z-80. The Z-80 component set is at present superior in both software and hardware capabilities to any other microcomputer system on the market today. For increased throughput the Z80A operating ata 4 MHZ clock rate offers the user significant speed advantages. Microcomputer systems are extremely simple to construct using Z-80 components. Any such system consists of three parts:
  • CPU (Central Processing Unit)
  • Memory
  • Interface Circuits to peripheral devices The CPU is the heart of the system. its function is to obtain instructions from the memory and perform the desired operations. The memory is used to contain instructions and in most cases data that is to be processed. For example, a typical instruction sequence may be to read data from a specific peripheral device, store it in a location in memory, check the parity and write it out to another peripheral device. Note that the Zilog component set includes the CPU and various general purpose I/O device controllers, while a wide range of memory devices may be used from any source. Thus, ali required components can be connected together in a very simple manner with virtually no other external logic. 2.

3.

4.

Page 69

General Purpose Registers There are two matched sets of general purpose registers, each set containing six 8-bit registers that may be used individually as 8-bit registers or as 16bit register pairs by the programmer. One set is called BC, DE and HL while the complementary set is called BC’, DE’ and HL’. At any one time the programmer can select either set of registers to work with through a single exchange command for the entire set. In systems where fast interrupt response is required, one set of general purpose registers and an accumulator/flag register may be reserved for handling this very fast routine. Only a simple exchange command need be executed to go between the routines. This greatly reduces interrupt service time by eliminating the requirement for saving and retrieving register contents in the external stack during interrupt or subroutine processing. These general purpose registers are used for a wide range of applications by the programmer. They also simplify programming, especially in ROM based systems where little external read/write memory is available. Arithmetic & Logic Unit (ALU) The 8-bit arithmetic and logical instructions of the CPU are executed in the ALU. Internally the ALU communicates with the registers and the external data bus on the internal data bus. Tne type of functions performed by the ALU include: Add Left or right shifts or rotates (arithmetic and logical) Subtract increment Logical AND Decrement Logical OR Set bit Logical Exlusive OR Reset bit Compare Test bit Instruction Register and CPU Control As each instruction is fetched trom memory, it is placed in the instruction register and decoded. The control sections performs this function and then generates and supplies all of the control signals necessary to read or write data from or to the registers, control the ALU and provide all required external control signals.

Z-80 CPU Pin Description The Z-80 CPU is packaged in an industry standard 40 pin Dual In-Line Package. The I/O pins are shown in the below figure and the function of each is described.

i2730Ay

<r

ie1932,

MREQ ~—— =» a, SYSTEM _- ong «2 } 3» a,

CONTROLaD2134

< }-—— A,

whwe|\—2-» a,

| 8 a,

(aH 2| 7a,
| 8a,ADDRESS
=1839BUS

HALT = <#——J 2-80 CPU -——— A, Lo me Ay

wait—4 9fptea,

CPU 2 CONTROL > An

nr8[2 An

nmi | 12 aw

__26=e

RESET ———— 2S CPU ‘BUSRO ras

BUS BUSAK =

CONTROL 4 ~ > D, bet 0, 6 12

®aneje 0,

1 8 45v }<+-—> 0. 7 DATA

aap~=—5]bam 0,BUS

D 2-80 PIN CONFIGURATION ee

Page 70

Ao-Ais (Address Bus) Tri-state output, active high. Ay-A;; Constitute a 16bit address bus, The address bus provides the address for memory (up to 64K bytes) data exchanges and for I/O device data exchanges. I/O addressing uses the 8 lower-address bits to allow the user to directly select up to 256 input or 256 output ports. Ay is the least significant address bit. During refresh time, the lower 7 bits contain a valid refresh address.

D,-D; (Data Bus) Tri-state input/output, active high. Do-D; constitute an 8-bit bidirectional data bus. The data bus is used for data exchanges with memory and I/O devices.

My, (Machine Cycle one) __ Output, active low. M, indicates that the current machine cycle is the OP code fetch cycle of an instruction execution. Note that during execution of 2-byte op-codes, M1 is generated as each op code byte is fetched. These two byte op-codes always begin with CBH, DDH, EDH or FDH. M1 also occurs with IORQ to indicate an interrupt acknowledge cycle. MREQ (Memory Request) Tri-state output, active low. The memory request signal indicates that the address bus holds a valid address for a memory read or memory write operation. 10RQ (Input/Output Request) Tri-state output, active low. The IORQ signal indicates that the lower half of the address bus holds a valid /O address for a I/O read or write operation. An 1ORQ signal is also generated with an M1 signal when an interrupt is being acknowledged to indicate that an interrupt response vector can be placed on the data bus. Interrupt Acknowledge operations occur during M, time while I/O operations never occur during M, time. RD (Memory Read) _ Tri-state output, active low. RD indicates that the CPU wants to read data from memory or an I/O device. The addressed I/O device or memory should use this signal to gate data onto the CPU data bus. WR (Memory Write) Tri-state output, active low. WR indicates that the CPU data bus holds valid data to be stored in the addressed memory or I/O device. RFSH (Refresh) Output, active low. RFSH indicates that the lower 7 bits of the address bus contain a refresh address for dynamic memories and the current MREQ signal should be used to do a refresh read to all dynamic memories.

HALT (Halt state) Output, active low. HALT indicates that the CPU has executed a HALT software instruction and is awaiting either a non maskable or a maskable interrupt (with the mask enabled) before operation can resume. While halted, the CPU executes NOP’s to maintain memory refresh activity.

WAIT (Wait) Input, active low. WAIT indicates to the Z-80 CPU that the addressed memory or I/O devices are not ready for a data transfer. The CPU continues to enter wait states for as long as this signal is active. This signal allows memory or I/O devices of any speed to be synchronized to the CPU.

INT (Interrupt Request) Input, active low. The Interrupt Request signal is generated by I/O devices. A request will be honored at the end of the current instruction if the internal software controlled interrupt enable flip-flop (IFF) is enabled and if the BUSRQ signal is not active. When the CPU_accepts the interrupt, an acknowledge signal ((ORQ during M, time) is sent out at the beginning of the next instruction cycle. The CPU can respond to an interrupt in three different modes that are described in detail in section 5.4 (CPU Control Instructions). NMI (Non-Maskable Interrupt) Input, negative edge triggered. The non maskable

interrupt request line has a higher priority than INT

and is always recognized at the end of the current instruction, independent of the status of the interrupt enable flip-flop. NMI automatically forces the Z-80 CPU to restart to location 00664. The program counter is automatically saved in the external stack so that the user can return to the program that was interrupted. Note that continuous WATT. cycles can prevent_the current instruction from ending, and that a BUSRQ will override a NMI. RESET Input, active low. RESET forces the program counter to zero and initializes the CPU. The CPU initialization includes:

  • Disable the interrupt enable flip-flop
Page 71
  • Set Register |= 00H
  • Set Register R =00x
  • Set Interrupt Mode 0 During reset time, the address bus and data bus go to a high impedance state and all control ouput signals go to the inactive state.

BUSRQ (Bus Request) Input, active low. The bus request signal is used to request the CPU address bus, data bus and tri-state output contro! signals to go to a high impedance state so that other devices can control these buses. When BUSR@Q is activated, the CPU will set these buses to a high impedance state as soon as the current CPU machine cycle is terminated. BUSAK (Bus Acknowledge) Output, active low. Bus acknowledge is used to indicate to the requesting device that the CPU address bus, data bus and tri-state control bus signals have been set to their high impedance state and the external device can now control these signals.

CLK (Clock) Single phase TTL level clock which requires only a 330 ohm pull-up resistor to +5 volts to meet all clock requirements.

3-6

Page 72

MANUFACTURER

68764 MOTOROLA —=—— 68766

MANUFACTURER EPROM NO.

MOTOROLA MCR SYSTEM P.C. BOARD JUMPER OPTIONS

VIDEO GENERATOR P.C. BOARD

SUPER C.P.U. P.C. BOARD

JUMPER OPTIONS FOR PROGRAM ROMS

INTEL, i

JUMPER OPTIONS

EPROM NO. MANUFACTURER

68764 MOTOROLA 68766

EPROM NO.

2532

2732 TA

INTEL

MANUFACTURER

NUMEROUS MFR'S

NUMEROUS MFR'S FOR BACKGROUND c =

  • = CUT JUMPER WIRES WHERE THIS SYMBOL “*” APPEARS. # = LEAVE JUMPER WIRES iN WHERE THIS SYMBOL “#” APPEARS.

The above table illustrates the fact that the Video Generator P.C. Board used in the MCR II System has 8 jumper wires, the SUPER C.P.U. P.C. Board used in the MCR II System has 19 jumper wires, and the Sound I/O P.C. Board used in the MCR li System has 2 jumper wires.

All of the above Boards can be used with a variety of different SETS of EPROM chips. However, these EPROMS are not all made by the same manufacturer and do have some iniernal differences. So, in order to make them function properly in their respective P.C. Boards, certain jumper wires on these Boards have to be cut.

The above table tells you which jumpers to cut (depending on which EPROM set you're going to use) by showing a “*” under that jumper wire's number. If there is NO “*” under a jumper wire’s number, THAT PARTICULAR JUMPER WIRE IS. NOT TO BE CUT.

Page 73

IV. Coin Door Maintenance

SPECIAL NOTE: If you have any questions about the coin acceptors in your game(s), please fee! free to contact their manufacturers. Each manufacturer's name is PROMINENTLY imprinted on every acceptor mechanism. Metal mechanisms only: Metal and Plastic mechanisms: COIN MECHANISMS, INC. COINCO COIN ACCEPTORS, INC. 817 Industrial Drive 860 Eagle Drive Elmhurst, IL 60126 Bensenville, IL 60106 Phone (312) 279-9150 Phone (312) 766-6781

COIN DOOR MAINTENANCE | 7

  • Remove the coin acceptor mechanism as METAL COIN ACCEPTOR MECHANISMS shown in Figure 4-1. Periodically, the metal coin acceptor mechanism(s) o Push down on the two spring loaded latches. must be removed from the coin door and cleaned. While holding the latches down, pull the top of the coin acceptor mechanism toward you.
  • Make sure the power to the game is off. D Release the latches and lift out the coin accep-
  • Unlock and open the coin door. tor mechanism.

TO REMOVE PUSH LATCHES DOWN

PLACE PEGS IN SLOTS TO REPLACE PULL MECHANISM OUT PUSH MECHANISM IN

Figure 4-1 Removing and Replacing the Coin Acceptor

Page 74

4, Clean the magnet of all foreign particles. See Figure 4-2. O This may be accomplished by swinging the gate open as shown in the above figure.

  • Remove the cradles and undersize levers and clean the bushings. (A pipe cleaner makes a good bushing cleaner.) C Also clean the pivot pin.
  • Whenever needed, the coin acceptor should be cleaned with hot water and cleanser in the foliowing manner: O Place the coin acceptor in boiling water for about ten minutes.

OC Next, use a brush and kitchen cleaner to remove all remaining foreign matter from the unit. C Rinse the coin acceptor in clean boiling water. O Dry the coin acceptor thoroughly by using filtered compressed air to blow it dry.

NOTE: The reason we recommend using boiling water is that it evaporates faster than cold water and speeds drying time.

GATE OPEN AS SHOWN CLEAN MAGNET BY DRAGGING A SCREWDRIVER BLADE ACROSS SURFACE

Figure 4-2 Cleaning the Metal Coin Acceptor

  • To \ubricate the coin acceptor: O Use ONLY powdered graphite and put it ONLY on the moving parts of the coin acceptor. These parts are called out in Figure 4-3. O Be extremely careful to keep the powdered graphite away frorn paths that are traveled by the coins.
  • WARNING — DO NOT USE OiL TO LUBRICATE THE COIN ACCEPTOR.
  • Check the coin chute for obstructions such as: paper, gum, etc.
  • Reinstall the coin acceptor to the coin door. See Figure 4-1. O Place the two pegs at the coin acceptor’s base into their retaining slots. O Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches.
  • Close and lock the coin door.

APPLY POWDERED GRAPHITE HERE

CRADLE

Figure 4-3 Lubricating the Metal Coin Acceptor

Page 75

SQUEEZE PINS TOGETHER TO UNLOCK SWING BOTH GATES OPEN

HOLDING BOTH GATES TOGETHER, PUSH UP AND PULL OUT

Figure 4-4 Opening the Plastic Coin Acceptor

PLASTIC COIN ACCEPTOR MECHANISMS The plastic coin acceptor mechanism(s) must be removed periodically from the coin door and cleaned. 1, Make sure the power to the game is off.

  • Unlock and open the cain door.
  • Remove the coin acceptor mechanism(s) as shown in Figure 4-1. O Push down on the two spring loaded latches. 0 While holding the latches down, pull the top of the acceptor mechanism toward you. CG Release the latches and lift out the mechanism.
  • Squeeze the two pins indicated in Figure 4-4 together to open the mechanism and break it down into its three basic parts. O Clean the mechanism in not soapy water. It never rusts. O Rinse the mechanism in clean hot water and allow it to dry. O Reassemble the mechanism (it never needs lubrication).
  • Check the coin chute for obstructions such as: paper, gum, etc.
  • Reinstall the coin acceptor to the coin door. See Figure 4-5. 0 Place the two pegs at the coin acceptor’s base into their retaining slots. O Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches.
  • Close and-tock the coin door.
NOTE: See Figure 4-6 for instructions on how to set the plastic coin acceptor mechanisms to either accept or reject Canadian quarters.
Page 76

ACCEPTOR CAN BE SET TO ACCEPT U.S. QUARTERS ONLY OR BOTH U.S. AND CANADIAN QUARTERS.

se

SLIDE MAGNET TO EXTREME RIGHT (AS SHOWN) TO ACCEPT BOTH U.S. ANO CANADIAN QUARTERS.

TO ACCEPT U.S. QUARTERS ONLY, SLIDE MAGNET TO EXTREME LEFT.

Figure 4-5 Changing the Plastic Coin Acceptor to Accept American or Canadian Quarters.

Page 77

Monitor Manual

PLEASE NOTE:

THE INFORMATION CONTAINED IN THIS SECTION IS TOLD IN AN EASY TO UNDERSTAND MANNER AND IS INTENDED TO AID THOSE WITHOUT AN ELECTRONICS DEGREE IN TROUBLESHOOTING AND REPAIRING THEIR GAMES T.V. MONITOR.

IF YOU READ THROUGH THIS SECTION AND STILL HAVE QUESTIONS, PLEASE CONTACT YOUR DISTRIBUTOR OR MIDWAY MANUFACTURING COMPANY AT THE TOLL FREE NUMBER PROVIDED WITH YOUR GAMES PAPERS.

OUR STAFF AND OUR DISTRIBUTORS STAND READY TO HELP YOU!

THANK YOU

Introduction: (How to

use this section of your manual.)

This section has been designed to simply familiarize you with one of the more mystical components in your game — the ‘T.V. monitor. If you are an electronics technician who is quite knowledgeable on the subject, you may decide to just go to the schematics and start troubieshooting the defective monitor. But if you are like most people, a monitor is a T.V. set, and that means a complex doo-dad that means big buck repairs. This isn't necessarily so. This section of the manual will acquaint you with the monitor and could just help you repair it if you feel adventurous enough to give it a try. If you have any knowledge of electronics, especially the use of a voltmeter, the repairs you can make are astonishing. Just keep in mind that ELECTRICITY CAN BE VERY DANGEROUS, SO BE CAREFUL!!

If you want to understand how a monitor works, just read the “THEORY OF OPERATION” subsection. If you wish, you can follow along with the schematics. The information is presented in a very basic manner but a more complete treatment of the subject can be found in the technical sections of bookstores.

If you want to attempt to repair your monitor, it would be a good idea to read this whole section beginning to end before starting. Pay attention to all warnings

5-1 and take them seriously. The more equipment you have the better, but a low cost Volt-Ohm-Milliameter can often do the trick. Here are the steps to take:

  • Find the symptom that matches the problems your monitor has in the “SYMPTOM — DIAG- NOSIS” subsection. The diagnosis tells the circuit or area the problem may be in and possibly even the actual component causing it.
  • Once you have the circuit that is causing the trouble, read the “TROUBLESHOOTING” subsection to learn the procedure for finding the bad part.
  • Next, go to the schematic section and find the schematic that matches your monitor. It may be helpful to read the “DIFFERENCES BETWEEN MONITORS” subsection if you are unsure of which monitor you have. Use the schematic to see what parts are in the offending circuit.

That really is all there is to it. Just remember that there are some bizarre or rare symptoms not covered, or that a monitor may have two or more different problems that only a genius, the experienced, or an experienced genius can figure out. But be patient, follow safety precautions, and remember that there is also literature available from the monitor companies through your distributor or from Bally Midway Manufacturing Company on request. (There is a toll free number on the back side of the front cover of this manual.)

Page 78

Symptom Diagnosis

  • Insufficient width or heighth: A. Horizontal line (due to VERTICAL CIR- CUIT DEFECT). C Bad yoke. O Bad vertical output section. Q Open fusible resistor in vertical section. Q Bad height control. C Bad flyback. B. Vertical line (due to HORIZONTAL CIR- CUIT DEFECT). O Bad yoke. O Open width coil. Open part in horizontal output section.
  • Picture spread out too far or crushed in certain areas: A. Horizontal or vertical output transistor. B. Bad Component in output circuitry. C. Vertical linearity or damper control needs adjustment.
  • Line too close with black spacing: A. Problem in vertical section causing poor linearity.
  • Poor focus and convergence: A. Bad high voltage transformer (“flyback”) or control. B. Focus voltage wire not connected to neckboard terminal.
  • Colors missing; check: Interface color transistors. Color output transistors. Cracked printed circuit board (neck Board). Color circuits. Video input jack. . Defective picture tube.
  • Picture not bright enough: A. Weak emission from picture tube.
  • Silvery effect in white areas; check: A. Beam current transistors. B. Weak picture tube emission.
  • Too much brightness with retrace lines; check: A. Beam limiter transistors. B. Brightness and/or color blanking control “set too high.
  • Increasing brightness causes an increase in size and poor focus. A. Weak high voitage rectifier or regulation (high voltage unit). B. Bad component in monitor's power supply. moOD> =

5-2 11.

12.

13.

14,

15.

16.

17.

18.

19. Small picture and/or poor focus: A. Low B+ voltage (power supply trouble).

Vertical rolling: A. Vertical oscillator in the IC. vertical sync. transistor, or circuit. B. No sync from logic board. C. Three pin sync. jack is loose or piugged in wrong. Horizontal line across center: A. Vertical output circuit is dead (see symptom No. 1. A.). B. Vertical oscillator is not putting out the right wave form.

Picture bends: A. Horizontal sync needs adjusting. B. Magnetic or electromagnetic interference. Flashing picture, visable retrace lines: A. Broken neck board. B. Internal short circuit in the picture tube (arcing). Unsymmetrical picture or sides of picture: A. Defective yoke. No brightness, power supply operating — No high voltage for the picture tube; check: A. Horizontal oscillator. B. Horizontal amplifier and output. C. Flyback transformer (high voltage unit). No brightness, high voltage present; check: A. Heater voltage to the tube at the neck board. B. Screen-grid voltage for the tube. C. Focus voltage. D. Grid to cathode picture tube bias. No high voltage; check: For AC input to the “flyback” Horizontal deflection stages. Flyback transformer. Yoke. Power supply. mOOD>

No horizontal and vertical hold; check: A. Sync transistors and circuit. B. Wires and jack from logic board to the monitor. . Wavey picture — (power supply defect); check: A. Transistors, diodes, electrolytic capacitors in the power supply.

Page 79

21.

23. Moving bars in picture: A. Ground connector off between monitor and logic boards. B. Defect in the power supply (see wavy picture symptom).

Washed out picture (see picture not bright enough): A. Check video signal at the cathode pins with an oscilloscope. If there is about 80 volts peak to peak, the picture tube has weak emission.

Monitor won't turn on: A. Problem in the power supply: Check fuse, transistors, open fusible resistor. B. Shorted horizontal output transistor. C. Defective high voltage disabling circuit. D. Crack(s) somewhere on main chassis board.

24, Can't adjust purity or convergence:

A. Useadegausser to demagnetize the picture tube carefully following your degausser’s instructions. B. Picture tube defective. C. Nearby equipment is electromagnetically interferring. D. The poles of the earth are pulling off the purity — see “A” above. E. Poor focus or width of picture. F. Make sure you have the correct CRT number for that brand of monitor.

Guide To Schematic Symbols

THERMISTOR (POLARITY DOESN'T MATTER)

SYYN

INDUCTOR, COIL, CHOKE (POLARITY DOESN'T MATTER)

(-) CATHODE

(+) ANODE

ZENER DIODE I iI

IRON CORE TRANSFORMER (SUCH AS A FLYBACK)

VL

FUSE (POLARITY DOESN'T MATTER)

CATHODE (-)

ANODE (+)

DIODE

Page 80

COLLECTOR a COLLECTOR 4a BASE ———> BASE———>

EMITTER — EMITTER me

NPN TRANSISTOR PNP TRANSISTOR

“WW

VARIABLE RESISTOR, POT, CONTROL RESISTOR (POLARITY DOESN'T MATTER) (POLARITY DOESN'T MATTER)

+

LINES ARE CONNECTED ELECTROLYTIC CAPACITOR

LINES ARE NOT CONNECTED CAPACITOR (POLARITY DOESN'T MATTER)

th a & GROUND

5-4

Page 81

Troubleshooting

Troubleshooting monitors requires experience, patience, and luck. The first step is to match the symptom the monitor displays to tne diagnosis next io it in the “SYMPTOM-DiAGNOSIS" subsection. This will pinpoint the circuit the problem is probably in, and often the parts to check. Next, the circuit should be visually inspected to see if there are any paris broken, burned, or if something is there that shouldn't be, like a loose screw, etc. Some parts go bad before others and should be checked first. In fact, following is the general order in which parts usually go bad:

  • Semiconductors (like transistors, diodes, and integrated circuits). Fusible resistors. Electrolytic capacitors. Resistors. Capacitors and coils. Always remember thata monitor can bite like a snake. Even when it is turned off, capacitors hold voltage and wili discharge it to you should you be touching chassis ground. The picture tube or CRT. itself, is a giant capacitor, so avoid the flyback anode plug hole. With the monitor on, the power supply circuit and/or the flyback, which puts out at least 23,000 volts, CAN BE KILLERS! Avoid handling power transistors (usually output transistors) or ICs, yoke terminals, and other high power components when the monitor is on.
WARNING: That picture tube is a bomb! When it breaks, first it implodes, then it explodes. Large pieces of glass have been known to fly in excess of 20 feet in ail directions. DO NOT carry it by the long, thin neck. Discharge its voltage to ground by shorting the anode hole to ground. Use a plastic handied screwdriver, connect one end of a wire with an alligator clip at each end to chassis ground and the other end to the metal shaft of the screwdriver. Using ONE HAND ONLY (put the other in your pocket) and touching ONLY the plastic handle of the screwdriver (DO NOT TOUCH THE METAL SHAFT) stick the blade of the screwdriver into the anode hole.
IMPORTANT! The side brackets of the monitor are chassis ground as is the aquadag, the picture tube’s dark conductive coating. BUT, on the ZENITH MONITOR there are metalic mounting parts which ARE NOT chassis ground. Discharging the CRT to these will damage the Monitor! son

5-5 Be prepared for a fairly loud pop and a flash. The longer the monitor has been turned off, the smalier the pop and dimmer the flash. But BE CARE- FUL, picture tubes will hold a very healthy charge for at least a week if not longer. Even after you've discharged it once, it may still carry a residual charge. It’s better ta be too careful than dead, which is why electronic equipment always carries stickers referring servicing to qualified personne!. Handle the side with the viewing screen against your chest when changing it. ALWAYS wear safety goggles when handling the picture tube.

To maintain the safety and performance of the moniter, always use exact replacement parts. For instance, the wrong components in the power supply can cause a fire, or the wrong color transistor may give a funny color to the picture. Service your monitor on a nonconductive firm table like wood, NOT METAL, and take off all of your jewelry just in case. With ail this in mind, you are ready to begin troubleshooting.

Observe the picturg carefully. Try to vary the appropriate control that would most likely affect your particular symptom. For example, if there is poor brightness or no picture, try turning up the brightness or contrast control. If the controls have no effect at all, chances are there is trouble with the control itself, the circuit it controls, or a nearby circuit that may be upsetting voltages. Go to the list of symptoms and determine with the schematic where the bad circuit is. .

CAUTION:

Keep in mind that capacitors hold a charge as can the picture tube (for at least a week and usually longer), and could shock you.

First, check for obvious visual defects such as broken or frayed wires, solder where it is not supposed to be, missing components, burned components, or cracked printed circuit boards. \f everything looks good up to this point, make sure that diodes, electrolytic capacitors, and transistors have their leads connected in the right polarity as shown on the schematic and the circuit board.

Turn on the power and measure the voltages at the leads of the active devices such as tubes, transistors, or integrated circuits. Any voltage that does not come within at least 10% to 15% of the voltage specified on the schematic indicates either a problem with that device or acomponent connected with it in the circuit. The next step is to use the ohmmeter to narrow down the field of possible offenders.

Page 82

To test a transistor, one lead of the ohmmeter is placed on the base; and the other lead piaced just on the emitter, then on the collector. A normal transistor will read either high resistance (infinite), or little resistance (400 to 900 ohms), depending on the polarity of this type transistor. Then the leads should be switched, one remaining on the base, and the other switched from the emitter to the collector. Now the opposite condition should result: the resistance should be infinite if it was lower when the other lead was on the base. Consistantly infinite readings indicate an open, and ashort is demonstrated by 0-30 ohms on most of these test readings. Finally, place one lead on the collector, then the other on the emitter. No matter which lead is used, there should be infinite resistance. Any lower reading, such as 50 ohms (which is typical on a bad transistor), indicates a short. This all sounds pretty coniusing, but a little experience on a good transistor will make you an expert in no time. Usually, thelowest ohmmeter setting is used tor testing transistors. Once in a great while a transistor may check out good on this test, but may actually be “leaky” or break down only on higher voltages. If in doubt, change tt. Itis also wise to check the transistor out of the circuit just in case some component in the circuit is affecting the ohmmeter reading. A diode is tested like a transistor except it only has two ieads. Again, there should be high resistance one way and little resistance the other. If it tests bad, take one lead out of the circuit in case some component is messing up the ohmmeter reading.

NOTE: DO NOT leave soldering equipment on the leads too long since all semiconductors, especially integrated circuits, are easily destroyed by heat.

Without special equipment, integrated circuits are checked by verifying the proper DC voltage on the pins and the correct AC wave form using an oscilliscope. BE CAREFUL: Shorting their pins can easily destroy them. Resistors are checked with an ohmeter and should usually be within ten percent of the value stated on them and on the schematic. You may have to desolder one lead from the printed circuit board. If you wreck the foil on the board, carefully solder a smal wire over the break to reconnect the conductive foil. Capacitors are tricky. Their resistance goes up when checked with an ohmmeter which shows acharging action. As they suck up current trom the meter, the voltage goes up and so does the resistance. If you are sure a particular circuit is giving you a problem and everything else checks out O.K., Electrolytic capacitors are prime suspects. Substitute a new one and keep your fingers crossed.

Theory of Operation

To understand what goes on inside the monitor, large general groups of circuits will be examined instead of laboriously analyzing the branches and small circuits that make up these groups. This will help avoid confusion and aid in a basic, concrete, knowledge of what makes up a monitor.

THE POWER SUPPLY — The AC going to the monitor from the game transformer is just like the voltage and current from your wall outlet. It jumps up and down going positive and negative sixty times a second. But a monitor needs nice, smooth DC; direct current, not alternating. So diodes chop up the AC and a big electrolytic capacitor filters it out to make it even smoother. Since the monitor is a big piece of electronic equipment, with many circuits demanding a lot of power from the power supply, there are also zener diodes and transistors. to help maintain a nice, constant, smooth voltage so that the monitor circuits don't jump around. And this is what happens when you see a wavy picture. There is AC creeping through the power supply, so it must be malfunctioning. If the voltage from the power supply is too low, the other circuits will be starved for power and you may see a small, wavy picture, or none at all. Some circuits receive voltages that are higher than what the power supply should put out. But they come from the flyback transformer which will be discussed later.

THE INTERFACE SECTION OF THE CHASSIS — The interface section of the chassis is fairly easy to identify. It is right by the place where the video jack(s) from the logic board(s) plug into. There are sets of transistors that receive the separate red, green, blue, and sync information from the cables that come from the logic boards. The circuits jack up the voltage and match impedances, or in other words, prepare the logic board outputs for the circuits that will really amplify them for the output devices such as the yoke in the case of the sync, or the picture tube that shows the colors.

Page 83

An interesting aside is that our sync is composite negative sync. That means two things:

  • The sync is a negative going wave form.
  • There are two pulses going at different speeds over the same wire: a. Vertical wave forms at 60 times per second (or Hertz) and b. Horizontal wave forms at about 15,750 times per second (Hz). The sync is amplified by a sync amplifier transistor and sent on its way to the oscillators. The sync or timing information will be explained along with the oscillator shortly. The color information is sent via wires to the neck board where the main amplification occurs. This will also be discussed later.

VERTICAL AND HORIZONTAL DEFLECTION— After the sync signal is amplified by the sync amp, it goes to two different sections, the vertical and horizontal circuits. Basically, the sync signals are for timing so the picture doesn’t mess up since it is assembled like an orderly jigsaw puzzie, but so fast that you can't see the electron beams for each color painting the picture on the screen. This will all become clear soon. For now, we will follow the 60 cycle component of the sync as it goes on its journey to the deflection yoke. The 60 cycle pulse goes to the vertical oscillator to make sure this circuit goes back and forth (or oscillates) at 60 times a second. Without this pulse keeping the circuit at the correct speed, it may get lazy and oscillate at 58 cycles or lower, or get ambitious and oscillate at.62 cycles or higher. At the wrong speed, the picture will start to roll up or down. A Wells Gardner 13” (K4806) or 19" (K4906, K4956) color monitor uses an integrated circuit for its sync section. An Electrohome 13” or 19” color monitor uses an integrated circuit 1C501 for its sync section. The Zenith monitor (CD19MXRFO6) also uses an IC for the sync processing. Wells Gardner uses HA11423, Electrohome uses HA11244, and Zenith uses 221-175 (their part number). These ARE NOT interchangeable! The idea is all the same. The output to the vertical amplifying transistors for all monitors must form a sawtooth wave form, sort of like a bunch of pyramids, racing through the yoke's vertical coils at 60 times a second

Along the way to the output transistors, the 60 cycle pulse is shaped and amplified to do the job: the yoke magnetically pushes the electron beam to fill the screen Out sideways looking at the screen with the greatest length going up and down. Or viewing the screen sitting tike a home television set, the amplified vertical output fills the screen up and down. Watching a monitor like this, seeing only a horizontal line means a problem with the vertical coils of the yoke or

5-7 anything from the vertical output section on back to the oscillator. The horizontal section is very similar with a few exceptions. The horizontal wave shape is more like a square and has a frequency of 15,750 cycles a second. Both Weils Gardner and Electrohome use the other side of their respective integrated circuits for the horizontal circuitry. If the oscillator isn't going at the correct speed, the picture may move sideways, start to slant, or tear up with slanted thin figures. With both the vertical and horizontal of all monitors, there are variable resistors that change the speed of the oscillators up and down. This way you have controls that can make the correct frequencies to keep the electronic jigsaw puzzle nicely locked in place. If you're driving in acar and next to yousomeone else is driving their car at exactly the same speed, it will appear that they are not moving. And this is why the sync frequency and the oscillator's frequency must match, so the picture doesn’t appear to move. The correct wave form is shaped and amplified in the circuitry just like in tne vertical section. But the horizontal! output transistor is a large power transistor and not only serves to give current to the horizontal yoke windings, it also feeds the flyback transformer.

THE FLYBACK TRANSFORMER (OR HIGH VOLTAGE UNIT) — The picture tube needs high voltage to light up, and the power supply can't meet this demand. The ilyback transformer receives current alternating at about 15,750 times per second from the horizontal output transistor. The “flyback” jacks up its input voltage and puts out a higher voltage alternating at the same speed. But, in your “flyback” there are diodes that chop up the alternating voltage to make it asmooth DC output just like in the power supply. This is what goes through that thick red wire to your picture tube. THIS AREA HAS ABOUT 24,000 VOLTS ON IT AND IT CAN KILL YOU! The “flyback” may be dangerous, but it is also generous. It has extra output windings which give voltage to the heater pins of the picture tube, voltage for the vertical deflection circuits, and picture tube screen-grid voltage. So in a way, the high voltage “flyback” is like a second power supply. COLOR CIRCUITS — The color circuits are pretty straight forward. The signals go into the interface section where some amplification and impedance matching occurs. These circuits are pretty sparse and simple. Each color just has two transistors and a diode with some resistors and capacitors. From here, the AC color signal is sent by wires to the neck board. The coior output circuits are on the neck board. The color signals going to the transistors are controlled by two variable resistors called drive controls. There are only two, one for the red and one for the green on

Page 84

Wells Gardner and Electrohome monitors. Zenith monitors have all three: red, blue and green. The Wells Gardner and Electrohome monitor have another variable resistor in their emitter part of their color output transistors. These “cutoff controls” vary the amount of A.C. signal that the transistor amplifies and sends to the cathodes of the picture tube. The Zenith monitor has its cutoff controls in the interface section to vary the amount of signal going to the output transistors. The more signal, the more color. If you think this is contusing, here is another little hitch. The Electrohome and Zenith monitors both have the actual A.C. picture information signal going through the emitters of the color output transistors. The Welis Gardner has the A.C. signal going to the base of the transistors. The blanking and beam limiting signals which come from the blanking and beam limiting transistors in the interface section go into the color output transistor base in the Electrohome and Zenith monitors, but enters into the emitter of the Wells Gardner monitor's color output transistor. Should you feel adventurous enough to look at this signal on an oscilloscope, it should look like a square, The beam limiter helps contro! the brightness level, and the blanking transistor rapidly turns the picture tube on and off so that retrace lines don't show up on the screen. By turning up the brightness on a good monitor, these four to six retrace lines can be seen slanting diagonally across the picture.

PROTECTION CIRCUIT —

To protect the high voltage section against voltages that are too high coming from the power supply which could cause X-rays to be emitted from the “flyback”, a circuit senses the higher power supply voltage and turns off the horizontal oscillator. Since the horizontal oscillator doesn't work, the horizontal output transistor has nothing to feed the “flyback” which in turn has nothing to feed the picture tube. The monitor will be silent, have no picture, and will appear to be off. But don't be fooled. There is still that excessive amount of voltage coming trom the power supply. To find out, check at pin two of Welis Gardner's IC501 and emitter of X04 for the Electrohome monitor. Check the 95 volt test point (located near the “flyback”) for the Zenith monitor. Here are the voltages you should receive: Wells Gardner = 130VDC Electrohome = 120VDC Zenith = 95VDC

The best place to measure this voltage on an Electrohome monitor is at a pin marked B1 on the chassis. This is because a 13 inch color Electrohome monitor, The GO7-FB0 or GO7-902, has an integrated circuit and very little else in the power supply. Still, there should be 120VDC at B1.

5-8 THE PICTURE TUBE (OR CRT) —

ATTENTION! For information on picture tube replacement types, go to the last section, “PICTURE TUBE INTERCHANGEABILITY”

The picture tube or CRT is an output device. In other words, the end result of the circuit's work is displayed by this part. Actually, the output of other circuits is in the neck of the picture tube. First, there is the heater. The heater boils off electrons from the cathodes so that they (the electrons) shoot up to the screen to excite the phosphors so that the three phosphors emit three colors of light. The cathodes are next, and again they emit electrons to turn on the tube phosphors, making it glow. A defective cathode may cause the particular color it handles to be missing. Next come the grids. The first grid is grounded. The following grid is the screen grid which receives about 300VDC depending on the brightness setting. The next grid closest to the picture tube screen is the focus grid which gets about one fifth the amount of voltage that is applied to the picture tube anode. After jetting from the cathode through all these grids, the electrons speed through a mask, a sheet of material with tiny holes, and then excite the tiny dots of phosphor in the inside surface of the picture tube screen. The green electron gun (or cathode and circuitry) spits out electrons which head for the green phosphors only. The same goes for the red and blue guns. The way the phosphor light blends determines the color seen. Should these electron beams become too intense, they may burn the phosphor. With the monitor off, this can be seen as a dark permanent image of the video information on the tube screen.

Differences Between Monitors

The easiest way to identify the brand of monitor you are working with is to find the manufacturer's name or model number printed on the chassis or chassis base. But what if the monitor was in a Texas dust storm or buried in voicanic ash and this information is no longer there? Fear not! Each monitor has its own peculiarities and the following should help to identify them: The ELECTROHOME G07-904 (19") and G07-902 (13”) have their horizontai and vertical processing IC hidden under a silver can. A shiny metal top behind the “VERTICAL HEIGHT” and “HORIZONTAL FRE- QUENCY” control prove this is an Electrohome monitor.

Page 85

The WELLS GARDNER K4906 (19") and K4806 (13”) have their horizontal and vertical processing !C out in the open directly behind the “VERTICAL HOLD" control. The ZENITH CO19MXRFO6 (19") monitor has its horizontal and vertical processing IC way in back by the picture tube. The monitor also has large white cables going from the main board to the neck board. K4306 (1st TYPE) — This monitor's identifying tags have BLACK ink printed on a white background. There is NO Vertical Damping Control. (This Control would be next to the Vertical Hold Contro\ but this area is jumpered with a small wire instead. K4906 (2nd TYPE) — This monitor's identifying tags have RED ink printed on a white background. There {S a Vertical Damping Control next to the Vertical Hold Control. The Damping Contro} provides a few more lines on the top of the monitor screen (monitor viewed as a normal T.V. would be) for any video game that may need these lines to fit the picture on the screen. Moving the Control may distort the top pari of your picture (or the side, depending on the game and how the monitor is mounted) so go ahead and move it if you are having this type of problem. To accommodate this new feature, there are a few circuit changes. ONE MAJOR DIFFERENCE BETWEEN THESE TWO VERSIONS OF THE K4906 IS THE YOKE. They look the same but notice the part numbers: K4906 WITHOUT the Damper Control: 2021111201 K4906 WITH the Damper Control: 2021111258 Since the companies like to change part numbers at the drop of a hat, the best thing to do is to request whatever part number is written on your yoke. If you should get the wrong yoke, the results will be: Picture distortion. Excessive brightness. Too much or too little vertical picture size.

CONTROLS YOU MAY NOT TOUCH Basically, on the Electrohome monitor, you can move any control you want EXCEPT for the B1 control. This sets the power supply voltage (ideally at 120 VDC) and is located right behind VERTICAL HOLD. The 13” Electrohome DOES NOT have this control. It may also be wise not to move the VERTICAL LIN- EARITY since this distorts the picture and is hard to reset perfectly. If you do move it, turn on the Cross Hatch Test Pattern of your game and try to get the squares to the point where they are equal in size by readjusting this Linearity Control.

On the Wells Gardner monitor, brightness is adjusted by the “BLACK LEVEL" Control which is right next to the Horizontal Frequency Control. Under the Focus Control is the “SCREEN” Control which youDO NOT touch. Yes, this contro! does adjust the brightness, but it is used to set the CRT bias and is adjusted at the factory. When Wells Gardner sets it, they mark the position with a black mark on the knob. If you move it, be sure to realign the mark and THEN set the BLACK LEVEL Control to the brightness you desire. So, other than the SCREEN control, you may adjust any of the controls. The Zenith monitor has a 95 volt adjustment control. It is green and located behind the jack labeled 3D3. To discourage you from moving it, Zenith has placed a little glue on top of this control.

Parts Interchangeability

Some parts can be interchanged on all of the monitors. Here are the rules:

  • You CAN swap any resistor between monitors that has the same resistance, wattage rating, and tolerance. . You CAN swap any capacitor between monitors ihat has the same capacitance and voltage rating.

. You CAN. swap many of the parts between the 19” and the 13” versions of each manufacturer's monitor. BUT, be certain to compare the manufacturers’ part numbers to be positive the parts you want to interchange are identical. BE SURE you have read the section DIFFERENCES BE- TWEEN MONITORS which was covered earlier.

You MAY BE ABLE to swap picture tubes between monitors. in the past you could swap any picture tube, but due to rampant engineering changes and new monitor models being introduced, you would need a computer to keep track of what could be swapped. For more information on this subject, go to “PICTURE TUBE INTERCHANGEABILITY”.

You CANNOT change any part that is a safety part, one that is shaded in gray on the schematic; it MUST be IDENTICAL to the original. To do otherwise IS DANGEROUS. For instance, the 13 inch Electrohome (G07-902) monitor “flyback” jooks identical to the 19 inch Electrohome (G07- 904) monitor “flyback”. In fact, there is even a 19 inch Electrohome (G07-905) monitor (which is an obsolete model) with a similar looking “flyback". NONE OF THESE ARE INTER- CHANGEABLE!

You CAN change any of the parts between the G07-904 and G07-907. They're essentially the same monitor except that the G07-907 has a vertically mounted picture tube.

Page 86

If there is any doubt about what parts can be swapped between each manufacturer's 19 inch and 13 inch models, compare the manufacturer's part number between each one. If they match up, they are the same part.

Picture Tube Interchangeability

13” MONITORS

There are currently two 13" monitors being used: the Wells Gardner K4806 and the Electrohome G07-902. The picture tubes used are NOT interchangeable. The pins on the neck of the CRT will not fit in the socket should you use the wrong CRT.

Here is a chart for all the 13” color monitors Bally Midway uses. ELECTROHOME WELLS GARDNER K4806 G07-902 — 370ESB22

  • 370KSB22

19” MONITORS Here it gets a little tricky. All of the picture tubes will fit no matter which is used. But if you use the wrong one, you will have problems with purity and/or dynamic convergence. Purity trouble means that the color won't be true. If you turn up the color control for one color, instead of seeing that solid color it will show blotches or blobs of other colors on the screen.

Trouble with dynamic convergence means that there will be color fringing around solid lines at the edges of the screen.

The only way to ensure that you avoid these problems is to get the right picture tube or the right substitute.

Here is a list of the 19” monitors and the CORRECT CRT numbers.

ALL ELECTROHOME G07-904 — ASVMNP22 RCA 19VMJP22 RAULAND 510UJB22 HITACHI

WELLS GARDNER K4906 — AQVLTP22 RCA 19VMLP22 ZENITH 19VMKP22 PHILLIPS

ZENITH CD19MXRF06 — I9VMLP22 ZENITH 19VLTP22 RCA 19VMKP22 PHILLIPS The factory recommended CRT type could change in the future for one reason or another, but the listed picture tubes will work. As a matter of fact, you can call another picture tube company to see if they have a replacement number to recommend. ..but caveat emptor — let the buyer beware.

Page 87

Notes Monitor

Schematics |

Page 88

Power Supply Vettege and Symbo!s

I

‘symbol ] Voltage Operating Circuit

15V | Vert. Osc. | | Syne | | i Bianking CRT Cut-Off

rz) | 190V | Horiz. Ose i | orz. Drive | | | Horz. Output Vert. Output

® 175V Video Output i

Q351 COLLECTOR

1VIDIV 200uSECIDIV 20VIDIV 10uSECIDIV

‘TP.31 DC COUPLED 402-3 BOTTOM LINE =0 VOC

2VIDIV 200MSECIDIV

LC. 301, PIN 3

1VIDIV SMSECIDIV 1VIDIV 20u SECIDIV

P82 ‘TP-31, AC COUPLED

20vIDIV SMSECIDIV 1VIDIV 200uSECIDIV

LC. 301, PIN 13, NEGATIVE SIDE OF ©303

5-12 1VDIV 200uSECIDIV 2VIDIV SMSECIDIV O.5/DIV SMSECIDIV

O.5/DIV 20u SEC/DIV

LC. 301, PIN 15

1VDIV 2MSECIDIV a sn me

SERVICE TECHNICIAN WARNING

X-RAY RADIATION PRECAUTION:

THIS PRODUCT CONTAINS CRITICAL ELECTRICAL AND MECHANICAL PARTS SSENTIAL FOR X-RAY RADIATION —

PROTECTION FOR REPLACEMENT PURPOSES, USE _ ONLY TYPE PARTS SHOWN IN THE ARTS LIST. 19” COLOR MONITOR SCHEMATIC DiAGRAM

MODELS 19K4901, 19K4906, 19K4951, 19K4956

CAUTION: FOR CONTINUED SAFETY, REPLACE SAFETY CRITICAL COM- PONENTS ONLY WITH MANUFAC- TURER'S RECOMMENDED PARTS. AVERTISSEMENT: POUR MAINTENIR LE DEGRE DE SECURITE DE L’APPAREIL NE REMPLACER LES COMPOSANTS DONT LE FONCTIONNEMENT EST CRITIQUE POUR LA SECURITE QUE PAR DES PIECES RECOMMANDEES PAR LE FABRICANT.

To «367 a202 1 5Y/ GR.

poe

ps), HOR ORE eeKnsP 3) 28¢24620K eke | gt UE Bea ss | ‘ZSTZ6I0BK

Vaws)

1e3ot ® # sync amp vosc Hose 9 f Hana23 se

SEGAUSSING CO (ror 1_f Ga [ie] becitton] ooce2

TT | oeak 9401 9.402 RED-OUT GREEN OUT OSCILLOSCOPE WAVEFORM PATTERN The waveforms shown are as observed on the wide band oscilloscope with the monitor turned to a reasonably strong signal and a normal picture. The voltages shown on each waveform are the approximate peak amplitudes. If the waveforms are observed on the oscilloscope with @ poor high frequency response, the corner of the pulses will tend to be more rounded than those shown and the amplitude of any high frequency pulse will tend to be less,

52 bur 28C2068.8/L88K 2SC2068L 8/1 85K 28C2068. 8 BK 2SCISI4BVE/CVE 2SCISI4BVCKVC 2SCISIABVC/CVC

ie Raia 7 Sho) ase We

(RCUTOFE] [6.CUTOFF] ete) So) | aco (ava) | ertinever Lo —t

‘aoe were)

41988! > cenrer Eo

ly, vase 988 (HOR Size] iow 1, [HORGENTERING] v.

K4901D, K4906D, K4951D 5833 K4956B

Page 89

REPLACEMENT PARTS LIST This monitor contains circuits and components included specifically for safety purposes. For continued protection no changes should be made to the origina! design, and components shown in shaded areas of schematic, or A*® on parts jist should be replaced with exact factory replacement parts. The use of substitute parts may create a shock, fire, radiation or other hazard. Service should be performed by qualified personnel only.

MAIN BOARD

Ret. No.Part No.DescriptionRef. No.Part No.Description

RESISTORS RESISTORS (CONT.)

R201203X6500-6451K Ohm, 5%, 1/4W CarbonR369203X5602-329680K Ohm, 5%, 1/2W Comp.
R202203X6500-52330 Ohm, 5%,1/4W CarbonR370203X6501-00233K Ohm, 5%, 1/4W Carbon
R203203X6500-405100 Ohm, 5%, 1/4W CarbonR371203X9014-5841K Ohm, 5%, 1 Metal Oxide
R204203X6700-327100 Ohm, 5%, 1/2W CarbonR372203x9101-11912K Ohm, 5%, 1W Metal Oxide
R205,203X6700-421270 Ohm, 5%, 1/2W CarbonR375203X6700-7636.8K Ohm, 5%, 1/2W Carbon
R206203X6500-540390 Ohm, 5%, 1/4W CarbonR376203X9104-404270 Ohm, 5%, 2W Metal Oxide
R207340X2201-934200 Ohm, 5%, 1/4W CarbonR377203X6500-447150 Ohm, 5%, 1/4W Carbon
R208203X6500-540390 Ohm, 5%, 1/4W CarbonR378203X6500-88610K Ohm, 5%, 1/4W Carbon
R209340X2201-934200 Ohm, 5%, 1/4W Carbon379203X6500-88610K Ohm, 5%, 1/4W Carbon
R210203X6500-540390 Ohm, 5%, 1/4W CarbonR380203X6500-8658.2K Ohm, 5%, 1/4W Carbon
R211340X2201-934200 Ohm, 5%, 1/4W CarbonR381203X6500-7242.2K Ohm, 5%, 1W Metal Oxide
R214203X6500-6451K Ohm, 5%. 1/4W CarbonR383203X9014-387150 Ohm, 5%, 1W Metal Oxide
R215203X6501-126100K Ohm, 5%, 1/4W CarbonR502203X6500-88610K Ohm, 5%, 1/4W Carbon
R216203X6500-6451K Ohm, 5%, 1/4W Carbon503204X1700-535150 Ohm, 5%, 15W Metal Oxide
R217203X6500-405100 Ohm, 5%, 1/4W CarbonR504203x9014-26747 Ohm, 5%, 1W Metal Oxide
R218203X6500-6451K Ohm, 5%, 1/4W CarbonR505203X6501-2092.2K Ohm, 5%, 1/4W Carbon
R219203X6501-126400K Ohm, 5%, 1/4W CarbonF506203X9104-10515 Ohm, 5%, 2W Metal Oxide
R220203X6500-6451K Ohm, 5%, 1/4W CarbonR507203X5602-185330K Ohm, 5%, 1/2W Comp
Re2t203X6500-405100 Ohm, 5%, 1/4W CarbonAwREO!204x 1625-058,3.3 Ohm, 5%, 10W WW
R222203X6500-7623.3 Ohm, 5%, 1/4W CarbonR701203X9105-1412.2 Ohm, 5%, 2W Metal Oxide
R224203X6500-16910 Ohm, 5%, 1/4W CarbonR702203X6206-4412.2 Ohm, 5%, 1/2W Carbon
R225203X6500-16910 Ohm, 5%, 1/4W CarbonvR201204x2070-072i-Fixed
R226203X6500-16910 Ohm, 5%, 1/4W CarbonVR301204x2070-084ixed
R227203X6501-04447K Ohm, 5%, 1/4W CarbonVR303204X2070-085500 Ohm-B Semi-Fixed
R228203X6500645,1K Ohm, 5%, 1/4W CarbonVR351204x2070-0722K Ohm-B Semi-Fixed
R229203X6700-421270 Ohm, 5%, 1/2W CarbonVR352204x2070-0722K Ohm-B Semi-Fixed
R230203X6500-8638.2K Ohm, 5%, 1/2W Comp.
R231203X6500-8638.2K Ohm, 5%, 1/2W Comp.
R232203X6500-8638.2K Ohm, 5%, 1/2W Comp.
R233,203X6500-468180 Ohm, 5%, 1/4W Carbon
R234340X2820-93482 Ohm, 5%, 1/4W CarbonCAPACITORS
R235340X2820-93482 Onm. 5%, 1/4W Carbon201203X0014-0881000 uF, 18V, Electrolytic
R236340X2820-93482 Ohm, 5%, 1/4W CarbonC202202X7200-064330 pF, 500V, Ceramic
R301203X6500-508270 Ohm,5%, 1/4W Carbon203202X7200-043,220 pF, 500V, Ceramic
302203X6500-8638.2K Ohm, 5%, 1/4W CarbonC204202X7200-043220 pF. 500V) Ceramic
R303203X6500-8638.2K Ohm, 5%, 1/4W CarbonC205203X0014-076470 uF, 16V, Electrolytic
R304203X6500-7242.2K Ohm, 5%, 1/4W CarbonC206203X1810-1490.1 uF, 125V Mylar
R305203X6500-8426.8K Ohm, 5%, 1/4W CarbonC207349X2232-1091022 uF, 100V Mylar
R306203X6003-2017.5K Ohm, 2%, 1/4W Carbon301203X0014-065330 uF, 50V Electrolytic
R307203X6500-8255.6K Ohm, 5%, 1/4W CarbonC302203X1600-563.0.033 UF, 50V Mylar
R309203X6500-96522k Ohm, 5%, 1/4W Carbon303203X0629-0373.3 UF, 50V Electrolytic
R310203X6500-98839K Ohm, 5%, 1/4W CarbonC304203X1600-3660.068 pF, 50V Mylar
R311203X6500-7623.3K Ohm, 5%, 1/4W CarbonC306203x0412.0122.2 uF, 16V Tantal
R312203X9014-7414.7K Ohm, 5%, 1/4W Carbon¢307203X1600-6340.033 uF, 50V Mylar
R313204X1450-5371K Ohm, 5%, 5W CarbonC308203X0025-1743.3 uF, 50V Electrolytic
R314203X6500-481220 Ohm, 5%, 1/4W CarbonC309203X1207-1000.068 uF, 100V PP.
R315203X6500-16910 Ohm, 5%, 1/4W CarbonC310203X0629-06110 uF, 100V Electrolytic
R316203X6500-7623.3K Ohm, 5%, 1/4W Carbonc3it203x0041-02510 uF, 160V Electrolytic
R317203X6700-10712 Ohm, 5%, 1/2W Carbon312202X7050-2481000 pF, 500V Ceramic
R318203X6500-540390 Ohm, 5%, 1/4W Carbon6313203x0040-05247 uF, 160V Electrolytic
F319203X6500-6451K Ohm, 5%, 1/4W Carbon0314203x1201-265,0.033 uF, 200V PP
320203X6501-00233K Ohm, 5%, 1/4W CarbonC315203X0629-0231 uF, 50V Electrolytic
R321203X6501-224270K Ohm, 5%, 1/2W Carbon351203X0629.0231 uF, 50V Electrolytic
R322203X6500-88610K Ohm, 5%, 1/4W Carbon©3652203X0619-04547 uF, 25V Electrolytic
R351203X6500-88610K Ohm, 5%, 1/4W CarbonC353203X 1190-0150.0082 pF, 50V Mylar-PP
R352203X6500785,3.9K Ohm, 5%, 1/4W CarbonC354203X06 19-04547 uF, 25V Electrolytic
R353,203X6501-08668K Ohm, 5%, 1/4W CarbonC365203X1600-3660.0068 pF, SOV Mylar
R354203X6500-7623.3K Ohm, 5%, 1/4W CarbonC356202X7050-4830.01 uF, 500V Ceramic
R355203X9205-1436.8K Ohm, 5%, 3W Metal Oxide6359202X8065-606100 pF, 500V Ceramic
R358203X5601-87856K Ohm, 5%, 1/2W CarbonC360202X7050-3660.0033 pF, 500V Ceramic
R360203X6500-561470 Ohm, 5%, 1/4W CarbonC361202X7050-4830.01 uF, 500V Ceramic
R361203X6500-88610K Ohm, 5%, 1/4W CarbonC362202X7203-0320.01 uF, 50V Ceramic
R362203x9014-6451.8K Ohm, 5%, 1W Metal Oxide50363203X1270-9118700 pF, 1.5 KV PP
RIES204Xx1527-7513.9K Ohm, 5%, 7W Metal OxideC365203X 1201-2650.33 uF, 200V PP
R364203X6500-24622 Ohm, 5%, 1/4W CarbonC366203X0019-02622 uF, 25V Electrolytic
R365203X6501-00233K Ohm, 5%, 1/4W CarbonC367202X8065-1626 pF, 500V Ceramic
R367203X6500-88610K Ohm, 5%, 1!4W CarbonC368202X7203-0320.01 uF, 50V Ceramic
R368203x5602-185330K Ohm, 5%, 1/2\V Comp.372203X1207-1250.1 uF. 100V PP

MAIN BOARD (CONT)

Ret. No.Part No.DescriptionNo.Part No.Description

CAPACITORS (CONT.) SEMICONDUCTORS (CONT.)

380202X7200-087470 uF, 500V Ceramic206200x3181-523,Transistor (NPN) 2801818
Acs01203X 1810-1490.1 UF, 125V MylarQ207200X3181-523,Transistor (NPN) 2SC1815G'
4c502202X7050-2821500 pF, 500V Ceramic208200X3181-523,Transistor (NPN) 25C1815GR
4.0503202X7810-2142200 pF, 125V Ceramic209200X3181-523,Transistor (NPN) 2SC1851G5
A.c504202X7810-2142200 pF, 125V CeramicQ210200x3181-523,Transistor (NPN) 28C1851GR
C505203x0220-075560 uF, 200V ElectrolyticQ301200X3181-523Transistor (NPN) 28C1851GR
C50603X0040-03422 uF, 160V ElectrolyticQ302200%3207-306Transistor (NPN) 25C2073LBGL2
507203X0041-05747 uF, 160V Electrolytic303200X3207-306Transistor (NPN) 28C2073LBGi2
701203x0019-0921000 uF, 25V ElectrolyticQ351200X3248-217Transistor (NPN) 2SC2482BK
C702203X0634-06110 uF, 100V Electrolytic352200X4589-802Transistor (NPN) 2SD898B
C703202X7050-2481000 pF, 500V Ceramicrace200X2300-033IC HA11423
A*1C501200X2600-183IC STR381

SEMICONDUCTORS

203201X2010-159Diode, 182076-27
0204201X2010-159Diode, 1S2076-27TRANSFORMERS & COILS
205201X2010-159Diode, 1$2076-27L351201X4710-134Coil, (RF Choke)
D206201X2010-159Diode, 1$2076-27L352201X5000-083Coil, Horiz. Size
D207201X2010-159Diode, 182076-27L701611X0004-007Coil, Adg.
D208301x2010.189Diode. $2076.271351202X 1300-080Transformer, Hor. Drive
0209201X2010-159Diode, 182076-27Ak 1352200X9720-301RVUnit M14
0301201X2010-165,Diode, ISs81
D302201X2010-159Diode, 1$2076.27MISCELLANEOUS
303201X2010-159,Diode, 1$2076-27AF501204X7120-073,Fuse, 4 Amp. 125V
0304201X2120-009Diode, RH-IV402206X5008-632Recep W Wire 3P-M-BG
0305201X2120-009Diode, RH-IVP201204X9600-466Plug, PWB 3P-J
0306201X2010-159Diode, 182076-27P202204X9601-477Plug, PWB 6P-Q
A501201X3120-216Diode, RM-1AVP401204X9600-298Plug, PWB 4P-B
AD502201X3120-216Diode, RM-1AVP501204X9600-249Plug, PWB 2P-B
4.0503201X3120-216Diode, RM-1AVP601204x9600-304Plug, PWB 4P-C
0504201X3120-216Diode, RM-1AVTHE01201x0100-112,Thermistor
D505201X3120-216Diode, RM-1AV
0506201X3120-216Diode, RM-1AV
D701201X2130-234Diode, RU-2VFINAL ASSEMBLY PARTS
702201X2120-009Diode, RH-1VA 88X0138-50619VLTP22 Pix Tube
Q201200X3181-523Transistor (NPN) 28C1815GR205X9800-158Lateral/Purity Assembly
202200X3181-523Transistor (NPN) 2SC1815GRA202X1111-201Yoke Deflection
2203200X4056-260Transistor (PNP) 2SA562-Y-TM204X9301-255CRT Socket
204200X4056-260Transistor (PNP) 25A562-Y-TM291X5004-262Automatic Degaussing Coil Unit
0205200%4056-260Transistor (PNP) 2SA562-Y-TM

NECK BOARD RESISTORS CAPACITORS

R401203x6000-729220 Ohm, 5% 1/4W CarbonC401202X7050-2691200 pF, 500V Ceramic
R402203X6500-540390 Ohm, 5% 1/4W CarbonC402202X7050-2481000 pF, 500V Ceramic
R403203X6000-661820 Ohm, 5% 1/4W CarbonC403202X7050-248,1000 pF, 500V Ceramic
R404203x6000-729220 Ohm, 5% 1/4W CarbonC404202X7050-2821500 pF, 1.5KV Ceramic
R405203X6500-540390 Ohm, 5% 1/4W CarbonC405202X7050-483,0.01 uF, 500V Ceramic
R406203x6000-661820 Ohm, 5% 1/4W Carbon
R407203x6000-729470 Ohm, 5% 1/4W Carbon
R408203X6000-998270 Ohm, 5% 1/4W CarbonSEMICONDUCTORS
R409208X6000-661820 Ohm, 5% 1/4W CarbonQao1200X3206-800Transistor (NPN) 28C2068LB
R410203X9104-82415K Ohm, 5% 2W M.O. FormingQa02200X3206-800Transistor (NPN) 2802068LB
Ratt203X9104-82415K Ohm, 5% 2W M.O. FormingQ403200X3206-800Transistor (NPN) 2SC2068LB
R412203x9104-82415K Ohm, 5% 2W M.O. Forming
R413203X6000-9982.7K Ohm, 5% 1/2W Gomp.us
Raid203X6000-9982.7K Ohm, 5% 1/2W Comp.MISCELLANEO
Rate203x0108 18422.onm 5% 2W Metal Oxidevoy206%5008-296RECEP W Wire 4P-E
i,5%.Plug, PWB 3P-A
Rata203X6500-7412.7K Ohm, 5% 1/4W Carbonpada.204X9600-254
R420203X6500-7412.7K Ohm, 5% 1/4W CarbonP4035eeePlug, Bin 1F-D
4P701204x9601-020Plug, PWB 4P-E
R421203X6500-7412.7K Ohm, 5% 1/4W Carbon
vR401204x2115-014500 Ohm, -B Semi-Fixed
R402204X2115-014500 Ohm, -B Semi-Fixed
vR403204X21 15-0065K Ohm, -B Semi-Fixed
vR404204X2115-0065K Ohm. -B Semi-Fixed
R405204x21 15-0065K Ohm, -B Semi-Fixed

§-13

Page 90

~ ‘I Slug ontex RED X101.XI03 end XI08 VIDEO AMR. 25¢454C X102.X104 and XI06 VIDEO AMP. 25A673C TosNoy Age Vere oUreuT 25Cz0I" or BSEISNAY g &

)x301,x302,x308,xs08 lsyne iC AMP gig f2sc454C or eaciees vom 5073 aot dy

[2

X01 POWER DRIVE 25C 2688 902 ERROR AMP 2SC1890

Schematic Notes Unless otherwise specified Resistance: (Q.) (K->KQ, M-MQ), 1/4 (W) carbon resistor Capacitance: 1 or higher-» (pF), less than 1 (yF) working voltage > 50 (V) ceramic capacitor 4 Inductance: (v H) 8 or YOKE Electrolytic Cap: Capacitance Value (» F)/working voltage (V), NP — non-polar (or bipolar) electrolytic cap. Refer to the parts list for additional component information. ———— or D — 2 indicates test point connection (701 X-RAY PROTECTOR 2301 HOR wv Bou —— ve Ont we ATER 7 Beeasae or 2sciees Hager BG, ascesr dspees hn indicates chassis ground unless otherwise specified 280820 ACIZOV 6OHz/SOHz Hz s10% indicates cycles per second For safety purposes (and continuing reliability) Aa replace all components marked with safety syrnbol with identical type.

NOTE: FR — fusible resistor «

00-4147-04 Parts identification on circuit boards: G07-CBO e.g. SU1126A (R107 = R1107) SU3030A (R113 = R3113)

Page 91

REPLACEMENT PARTS LIST—ELECTROHOME 19” MONITOR

Components identified by the A symbol in the PARTS LIST and on the Schematic have special characteristics

important to safety.

DO NOT degrade the safety of the set through improper servicing.

Abbreviations for Resistors and Capacitors

Resistor Capacitor

CR:Carbon ResistorC Cap.Ceramic Capacitor
Comp. RComposition ResistorM Cap.Mylar Capacitor
OMR:Oxide Metal Film ResistorE Cap.Electrolytic Capacitor
VR:Variable ResistorBP E Cap.Bi-Polar (or Non-Polar)
MFR:Metal Film ResistorElectrolytic Capacitor
CMF RCoating Metal Film ResistorMM Cap.Metalized Mylar Capacitor
UNF RNonflammable ResistorPP Cap.Polypropylene Capacitor
FR:Fusible ResistorMPP Cap.Metalized PP Capacitor

PS Cap. Polystyrol Capacitor Tan. Cap. Tantal Capacitor

NOTE: When ordering replacement parts please specify the part number as shown in this list including part name, and model number. Complete information wil! help expedite the order.

Use of substitute replacement parts which do not have the same safety characteristics as specified, may create shock, fire or other hazards. For maximum reliability and performance, all parts should be replaced by those having identical specifications. .

SERVICE REPLACEMENT PARTS LIST

Symbol Description Main PC.B. Ass'y CRT Socket RC.B. Ass'y Purity Shield Ass'y

Outside of the P.C.B. Ass'y Symbol _ Description Picture Tube 19" A A\Deftlection Yoke PC Magnet A AFlyback Transf. A AHVR ROS UNF Resistor 220.0,25W K co4 C Capacitor 150pF, AC1.5KV X01 Si. Transistor x02 Si. Transistor sc Screw #8-% Sc Screw % x % Pix Tube Mtg. (4) WA Pyramida! Lock Washer (4) Nut Retainer, Pix Tube Mtg. (4) Clip—RC.B. Support Standoff Wire Terminal (Gnd. Strap) Terminal Lug (Gnd.) Groundstrap Assy. Grounding Spring Wire Hook (Gnd. Strap) Purity Shield Holddown Clamp Support Brkt. RH Support Brkt. LH Chassis Base Yoke Wedge (3) Part Number SU-1133A SU-3032A 07-220083-03

Part Number 17-7198-03 A29779-D=21-141-01 A75034-B=29-32-01 A29951-B A46600-A QRF258K-221 QCZ0101-005 2SD870 28C1106A 31-610818-06 31-601418-12 33-255-01 33-494-01 33-629-02 33-670-010R-02 34-228-03 34-33-04 34-574-02 35-212-03 35-3053-02 35-2348-01 35-3890-01 35-3890-02 38-449-02 39-1233-01 Purity Shield Ass’y. Parts List

Symbol Description Degaussing Coil D911, D912 Rectifier 1 Amp 600V (2) Pin Terminal (2) Pin Terminal Housing Purity Shield (2 pcs.) Purity Shield (2 pcs.) Cott Capacitor 100nF 10% 400V R921 Resistor, Wirewound 332, 4W Fire Retardant Term. Strip 4 Lug Part Number 21-1007-30

28-22-27 34-708-01 34-709-01 35-3847-01 35-3847-02 48-171544-62 42-113301-03 34-492-09

CRT Socket P.C.B. Ass'y (SU-3032A) Parts List

Resistors Symbol Description

R3105vR200
R3106vR200
R3113vR 5K
R3114VvR5K
R3115VvRSK
R3116OMR=10K22W J
R3117OMR10K22WJ
R3118OMR10KQ2WJ
R3119Comp.R3.3K2%W K
R3120Comp.R3.3KQ%WK
R3121Comp.R3.3K2%4WK

Capacitors Symbol Description

C3107ECap.10uF 250V A
C3108CCap.1000pF DC1400V P

Part Number QVZ3234-022 QVZ3234-022 QVZ3234-053 QVZ3234-053 QVZ3234-053 QRGO29J-103 QRGO29J-103 QRGO29J-103 QRZ0039-332 QRZ0039-332 QRZ0039-332

Part Number QEWS53EA-106 QCZ9001-102M CRT Socket P.C.B. Ass'y (SU-3032A) Parts List (Cont)

Coils Symbo! L3101

Semiconductors Symbol X3101 X3102 X3103

Miscellaneous Symbol A Description Peaking Coil

Description Si. Transistor Si. Transistor Si. Transistor

Description ACRT Socket

Main PCB Ass’y (SU-1133A) Parts List Resistors Symbol R1406 R1408 R1410 R1414 R1415 R1421 R1422 AFR1401 AR1503 R1504 R1509 R1512 R1514 R1515, R1522 R1523 R1528 R1534 VR1501 AR1703 AR1704 AR1901 R1902 R1903 R1904 R1905, Aq1908 AR1909 R1910 AFR1901

Capacitors Symbol C1301 C1402 1407 C1414 C1412 C1508 Ac1512 AC1513 Aci514 C1515 C1520 C1523 C1524 AC1531 AC1532 C1904 C1905 Description VR 2000 VR 2002

CMFR6.801WJ
OMR33KQ1WJ
OMR27KQIWS
OMR12KQ2WJ
VvOR10KQ

AF = R 6822WK

ACMFR11.8KQ%W+1%

VOR 8KQ

OMR10K22W J

OM R 8.2k22WJ

OMR82022WJ
CMFR8201WJ
CMFR4.701WJ
OMR6822W J
OMR39021WJ

ZN OR ZN oR

ACMFR390%4W+1%
ACMFR7.68KQ%W+1%

AsPosistor

UNFR207WK
CMFR4.703WJ
OMR10K@2WJ
OMR18KQ1WJ
ACMFR472%W+1%

VR 2ka

ACMFR_2.74KQYW+1%

AF — R 2200%WK

Description BPE Cap. 3.3uF SOV A Tan Cap. 2.2uF 16V K E Cap. 4.7uF 6.3VA E Cap. 100uF 160VA E Cap. 3.3uF 160VA PP Cap. 5600uF SOV J APP Cap. 2000pF DC1500V J APP Cap. 2000pF DC1500V J APP Cap. 2000pF DC1500V J PP Cap. 0.53uF DC1200V J BPE Cap. 3.3uF SOV A E Cap. 1uF 160V A M_ Cap. 0.1uF 200V K APP Cap. 2000pF DC1500V J A\PP_ Cap. 1500pF DC1500"’ J E Cap. E Cap. 10uF 250V A Part Number QQL043K-101

Part Number 28C1514VC 2S8C1514VC 28C1514VC

Part Number A76068 .

Part Number QVZ3230-002 QVZ3230-002 QRX019U-6R8 QRGO19J-332 QRG019J-272 QRGO26J-123Z QVZ3230-014 QRHO024K-680M QRV142F-1182 QVZ3230-053 QRGO26J-103Z QRG026J-822Z QRGO26J-821Z QRX019J-8R2 QRX019J-4R7 QRG026J-680Z QRGO19J-391 ERZ-CO5ZK471 ERZ-CO5ZK271 QRV122F-3902 QRV142F-7681 A75414 QRFO76K-2RO QRX039J-4R7 QRGO26J-103Z QRGO19J-183 QRV122F-470Z QVP5A0B-023E QRV142F-2741 QRH124K-221M

Part Number QEN61HA-3352 QEES1CK-225B QEWS51JA-475 QEWS52CA-107 QEW52CA-335 QFP31HJ-562 QFZ0082-202 QFZ0082-202 QFZ0082-202 QFZ0067-534 QEN61HA-335Z QEW62CA-105Z QFM720K-104M QFZ0082-202 QFZ0082-152 QEY0034-001 QEWS2EA-106 Main PCB Ass'y (SU-1133A) Parts List (Cont.) Coils Symbol L1502 L1503 L1504

Transformers Symbol T1501 T1503

Semiconductors Symbol 11501 X1101 x1102 X1103 X1104 X1105 X1106 X1301 X1302 X1303 X1304 X1305 X1401 x1402 X1501 X1901 X1902 D1101 D1102 D1103 D1301 D1401 D1402 D1503 D1504 D1505 01506 D1507 01508 Ap1701 A\D1901 A\D1902 AD1903 A\D1904 A\D1905

Miscellaneous Symbol AF1901 AF1902 Description Linarity Coil Width Coil Heater Choke

Hor. Drive Transf. Side Pin Transf.

Description Ic Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Diode Si. Diode Si. Diode Si. Diode Si. Diode Zener Diode Si. Diode Si. Diode Zener Diode Si. Diode Si. Diode Si. Diode AXZener Diode ASi. Diode ASi. Diode ASi. Diode ASi. Diode AZener Diode

Description AFuse 1.25A AMUL Fuse 3A Part Number A39835, C30380-A C30445-A

Part Number A46022-BM C39050-A

Part Number HA11244 2SC1685(R) 2SA673(C) 28C1685(R) 2SA673(C) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SC1685(R) 28D478 2SD478 2SC2610BK 2SC2688 (K.L.M.) 2SC1890A (E.F) WO6A WO6A WO6A 18Z473H 18Z473H RD10F(C) HF-1 VO9E RD11E(B) WO6A 18881 18Z473H RD20EV2 181887A 181887A 181887A 1S81887A RD6.8EV3

Part Number QMF53U1-1R25S QMF66U1-3ROS

5-15

Page 92

Mo OMtty Lut X10! XIO3 ong XIOS VIDEO AMP, 28C454C g 28¢1608, XiO2.Xi04 end XIO6 ViDEO AMP 2846736

el SU-I103A MAIN PCB ASSY

aor | 02, 401, x402 j2so478

X70) X-RAY PROTECTOR SELB PIE ascosry 385880 a sss [- Ps von 28C434C or 28¢261\ or 28CZ610BK 250869 oO} pel ii on

G07-FBO

00-4147-03

5-16 Schematic Notes Unless otherwise specified Resistance: (92) (K--KQ, M+MQ), 1/4 (W) carbon resistor Capacitance: 1 or higher-» (pF), less than 1-> (yF) working voltage —» 50 (V) ceramic capacitor Inductance: (/ H) Electrolytic Cap: Capacitance Value ( F)/working voltage (V), NP — non-polar (or bipolar) electrolytic cap. Refer to the parts list for additional component information. 2 indicates test point connection ohn indicates chassis ground unless otherwise specified Hz indicates cycles per second For safety purposes (and continuing reliability) A replace all components marked with safety symbol with identical type.

NOTE: FR - fusible resistor —ax-

Parts identification on circuit boards: e.g. SU1126A (R107 = R1107) SU3030A (R113 = R3113)

Page 93

REPLACEMENT PARTS LIST—ELECTROHOME 13" MONITOR

Components identified by the A symbol in the PARTS LIST and on the Schematic have special characteristics

important to safety.

DO NOT degrade the safety of the set through improper servicing.

Abbreviations for Resistors and Capacitors

Resistor

CR:Carbon Resistor

Comp. R Composition Resistor OM R Oxide Metal Film Resistor

VR:Variable Resistor

MFR Metal Film Resistor CMF R Coating Metal Film Resistor UNF R Nonflammable Resistor

FR:Fusible Resistor
NOTE: When ordering replacement parts please specify the part number as shown in this list including part name, and Capacitor

C Cap. M Cap. E Cap. BPE Cap.

MM Cap. PP Cap. MPP Cap. PS Cap. Tan. Cap.

model number. Complete information will help expedite the order.

Use of substitute replacement parts which do not have the same safety characteristics as specified, may create shock, fire or other hazards. For maximum reliability and performance, all parts should be replaced by those having identical specifications.

SERVICE REPLACEMENT PARTS LIST

Symbol Description Main PC.B. Ass'y CRT Socket PC.B. Assy

Outside of the P.C.B. Ass'y Symbol Description Avot APicture Tube 13" Apyo1 ADeflection Yoke PC Magnet Wedge AFlyback Transf. Art AFocusVR AROS UNF Resistor 2202,25W. K Aco4 = AC Capacitor 150pF, A C1.5KV X01 Si. Transistor 1Co1 IC Regulator Lo1 Degaussing Coil Degaussing Coil Pin Terminal (2) Degaussing Coil Pin Terminal Housing Groundstrap Ass'y Groundstrap Wire Terminal Groundstrap Spring (2) BR Support Bracket RH BR Support Bracket LH sc SCREW 10-% Pix Tube Mtg. (4) WA Pyramidal Lockwasher (4) Clip P-C.B. Support (2) Ground Lug CH Chassis Base Part Number SU-1103A, SU-3016A

Part Number 370ESB22(E) C29123-V A76366-A 30006 A19183-A A46606-A QRF258K-221 QCZ0101-005 2SD869 STR383 21-1007-31 34-708-01

34-709-01 34-697-04 34-228-03 35-3560-01 35-3919-01 35-3919-02 31-631018-08 33-255-01 33-629-02 34-33-04 38-452-01 Main P.C.B. Ass'y (SU-1103A) Parts List

Resistors Symbol R1406 R1408 R1410 R1414 R1415 R1421 R1422 AXFR1401 AR1503 R1504 R1509 R1511 R1514 R1515 R1522 R1523 R1528 R1534 VR1501 AR1703 AR1704 AR1901 R1902 R1903 R1904 AFR1901 Ceramic Capacitor Mylar Capacitor Electrolytic Capacitor Bi-Polar (or Non-Polar) Electrolytic Capacitor Metalized Mylar Capacitor Polypropylene Capacitor Metalized PP Capacitor Polystyrol Capacitor Tantal Capacitor

Description Part Number

VR2002QVZ3230-022
VR2002QVZ3230-022
CMFR6801WJQRX019J-6R8
OMR33KQ1WJQRGO19J-332
OMR27KQ1IWJQRGO19J-272
OMR12KQ2WJQRGO29J-123
VR10KQVZ3224-014H
AF— R6822WKQRHO24K-680M
ACMFR=11.82%W +1%QRV142F-1182
VR5KQQVZ3230-053
OMR10KQ2WJQRGO29J-103
OMR56KQ2WJQRGO29J-562
OMR68022WJQRGO29J-681
CMFR8201WJQRX019J-8R2
CMFR 4701WJQRX019J-4R7
OMRSs602WJORGO29J-560
OMR39021WJORGO19J-391
ZNoRERZ-CO5ZK471
ZNORERZ-CO5DK271
ACMFR39KQ%W +1%QRV122F-3902
ACMFR7.68KQ%W +1%QRV142F-7681

A?Posistor A75414

UNFR207WKQRFO76K-2RO
CMFR5623WJQRX039J-5RE
OMR10K22WJQRGO26J-103Z
AF= R22028%WKQRH124K-221M

Capacitors Symbol C1402 C1411 C1412 C1508 C1511 AC1512 Main P.C.B. Ass'y (SU-1103A) Parts List

Description Tan. Cap. 2.2uF 16V K E Cap. 100uF 160V A E Cap. 3.3uF 160V A PP Cap. 5600pF 50V J E Cap. 47uF 160VA AXPP_ Cap. 2000pF DC1500V J Ac1513_ APP Cap. 2000pF DC1500V J AC1514 APP Cap. 2500pF DC1500V J

C1515,PPCap. 0.53uF DC1200V K

C1520 BPE Cap. 1uF SOVA

C1524M_Cap. 0.1uF 200V K
C1904ECap.
C1905ECap. 10uF 250VA

C1907 A\MM Cap. 0.1uF AC150V Z

Coils Symbol Description 1501 Peaking Coil L1502 Liniarty Coil L1503 Width Coil 11504 Heater Choke L1901 Line Filter

Transformers Symbol Description T1501 Hor. Drive Transf. T1503 Side Pin Transf.

Semiconductors Symbol Description 1C1501 1c. X1101 Si. Transistor X1102 Si. Transistor X1103 Si. Transistor X1104 Si. Transistor X1105, Si. Transistor X1106 Si. Transistor X1301 Si. Transistor X1302 Si. Transistor X1303 Si. Transistor X1304 Si. Transistor X1305 Si. Transistor X1401 Si. Transistor X1402 Si. Transistor X1501 Si. Transistor X1701 Si. Transistor 01101 Si. Diode D1102 Si. Diode D1103 Si. Diode 01301 Si. Diode D1401 Si. Diode D1402 Zener Diode D1503 Si. Diode D1504 Si. Diode D1505 Zener Diode D1506 Si. Diode D1507 Si. Diode D1508 Si. Diode 4D1701 AdZener Diode Apd1901_ — ASi. Diode AD1902 ASi. Diode AD1903 ASi. Diode A\D1904 ASi. Diode

Miscellaneous Symbol Description AFi901_— AFuse 1A AF1902 AUL Fuse 3A CRT Socket P.C.B. Ass'y (SU-3016A) Parts List Resistors

Part NumberSymbolDescription
QEES1CK-225BR3105VR 2002
QEWS2CA-107R3106VR 2002
QEW52CA-335R3113VR 5KQ
QFP31HJ-562R3114VR 5KQ
QEW52CA-476SR3115,VR SKQ
QFZ0082-202R3116OM R 10K22W J
QFZ0082-202R3117OM R 10K22W J
QFZ0082-252R3118OM R 10K22W J
QFZ0067-534R3119Comp. R 3.3K2%4W K
QEN61HA-105ZR3120Comp. R 3.3KQ%W K
QFM72DK-682MR3121Comp. R 3.3K2%W K

QEY0034-001 QEWS52EA-106 Capacitors

QFZ9008-104SymbolDescription

C3107 E Cap. 10uF 250VA C3108 C Cap. 1000pF DC1400V P Part Number A75360-6 Coils

A39934SymbolDescription
€30380-AL3101Peaking coil

C30333-A A39475-J Semiconductors Symbol Description X3101 Si. Transistor

veneeredX3102Si. Transistor
A46022-BMX3103Si, Transistor

©39050-A Miscellaneous Symbol Description Part Number A CRT Socket

HA11244 2SC1685(R) 2SA673(C) 2SC1685(R) 2SA673(C) 28C1685(R) 2SA673(C) 2SC1685(R) 2SC1685(R) 2SA673(C) 2SC1685(R) 28C1685(R) 28D478 280478 2SC2610BK 2SC1685(P-S) WO6A WO6A WO6A 182473H 182473H RD10F(C) HF-1 VO9E RD11E(B) WO6A 18881 182473H D20EV2 1S1887A 1S1887A 181887A 181887A

Part Number QMF53U1-1ROS QMF66U1-3ROS Part Number QVZ3234-022 QVZ3234-022 QVZ3234-053 QVZ3234-053 QVZ3234-053 QRG029J-103 QRGO29J-103 QRGO29J-103 QRZ0039-332 QRZ0039-332 QRZ0039-332 -

Part Number QEWS52EA-106 QCZ9001-102M

Part Number QQL043K-101

Part Number 28C2611 28C2611 28C2611

Part Number A75522

5-17

Page 94

To rok YOKE r

;

VERT. LOW_Ir
Twist CABLE_-_ae oo:
asgr |rf
leakay hy'|
8|re1 70 5 apo EB;|
| [oe|| e863)j
VERT—a.caiseKCRa276 x R: Serazsoea2es beaoae||i
taliflteae | ewaere x ns219 raeso' Raz6#gaze danas HT 7 ||a:
Taioe aNt‘=|Hl'1
|i|&)||!1___| a ,
——:c2i3t i po10sTt|11T
! i:r|'xi !
jMe ae113228 Laszo|iL IL'
| |=vBe aR'1xa223| 1
|poeee tiiHl| H
|| 21| I
|a11| R2111
i| fap}‘i\|. '

’ '

_4|Haoxen
|'cee | r *i1
\wiion? |Ӵ\| reae02 | Cy Low |
|TioeuaeWY Ty txse08|ssobh |
93204| SIE= MeerO13 Cx32281I1 |
|3288,axs202mes!pees1
|1SHUTDONN121-9757 BeKT111

' |

&crszn< AicHr|!
i:xs204VOLTAGED1 j
—_aegists nen7an|
sta"’iLa
pe a vorerases RX3240, (3208 3215 | “4|
ud iper|1REFERENCE ONLY

; -

m1. 4oVv i} PP mc te

1303 row | OBa~

| agaae | vioget >) | SCHEMATIC FOR

==G- 186-03

Ley | ome -

5-18 RGB SWEEP BOARD COLOR MONITOR

ZENITH

RADIO CORP... CHICAGO, ILL. = ]

BS}9-186|

M05 1-00087-A021

vores: NOTES. custo met cin ERENCE OF SIGNATORS)

-Vale AESISTORS ARF 1/6 Mary FILM }S% TOLERANCEA. Brus SEE PARTS LIST FOR APPLICABLE USAGE,
[fl one crouse“S,LESS BTR REE SG aE8 oe sumpeR sine USED IHS Te30,
‘oncuNne 2a JELTORS ERE IN MICROFAKEDS ULESce @— PROVISION ON PRINTEE CIRCUIT BOARD.

SvEaWise SPECIFIED

Page 95

SWEEP BOARD (9-186-03)

Ref. No.PartNo.DescriptionRef. No.Part No.Description

CAPACITORS TRANSFORMERS & COILS

213122-750847 ME, 35V, +20% Electrolytic13207149-454Core, Ferrite Bead
215222-7508-01C22 MF, 35V, +20% Electrolytic1.3220F-13834Core & Sleeving Assy. (149-509-01)
6320122-7410-0510 MF, 100V, +20% ElectrolyticLx326120-3976Coil Width
cx320222-7710-01C1 MF, 50V, +50%~10% ElectrolyticLx326220-3975Coil, Linearity, with 205-271 Hot Melt
320322-7711-08C47 MF, 63V, +50%—10% Electrolytic7320595-3344Transformer, Horizontal Driver
x320422-7773-24A0.1 MF, 100V, +5% PolyesterTx320495-3581-01Transformer, Sweep
Cx3205,22-7523-010.01 MF, 2KV, +20% Disc
C320622-7708-04C4.7 MF, 25V, +50%—10% ElectrolyticRESISTORS
320722-5665330 PF, 1000V, +10% Disc9921-1.mm, 5%1/4
320922-72420.0018 MF, 200V, +10% DisceroGresetedae Onn, ou AW Fin
321122-7777-2080.047 MF, 200V, + 10% PolyesterR11163-9919-833K Ohm, +2% 1/4W Film
rtbolls560 PF, SOOV, 10% DiscR211263-9919-9610K Ohm, +2% 1/4W Film
©321322-7775-16A0.022 MF, 100V,#:20% Polyester@X320463-9921-802.2K Ohm,+5% 1/4W Film
321422-7775-10A0.0088 MF, 100V,+20% PolyesterRX320663-78053.3K Ohm, =5% 1/2W Carbon
321622.0684,470 PF, SOOV, +20% DiscRX320763-9921-3222 Ohm, +5% 1/4W Film
C3217peceee,470 PF. S00V, #20% DiscRX320863-10235-802.2K Ohm, +5% 1/4W Film
C321822-7774-15C0.018 MF, 100V, +10% PolyesterRX320963-10235-721K Ohrn, +5% 1/4W Film
322222-7742-100.001 MF, SOV, +10% AxialRX321083-78053.3K Ohm, +5% 1/2W Carbon
Cx320822-6486530 PF. 3KV, 10% DiseRX321163-10810-073K Ohm, +1% 1/2W Film
Cx322922-7672-070.013 MF, 1.6KV, +5% PolypropyleneAX321463-10233-812.4K Ohm, +2% 1/4W Film
©323322-77280.68 MF, 200V, + 10% PolyesterRX321663-10810-061.2K Ohm. +1% 1/2W Film
0324422-7566-240.1 MF, 250V, +10% PolyesterRX321763-7760270 Ohm, +5% 1/2W Carbon
0326122-7683-010.68 MF, 200V, +5% PolypropyleneRX321563-10235-9812K Ohm, +5% 1/4W Film
RX321863-10235-822.7K Ohm, +5% 1/4W Film
SEMICONDUCTORSAX321963-10235-884.7K Ohm, +5% 1/4W Film
cR3202103-142-01Diode, Low VoltageR322463-9946-884.7K Ohm, +5% 1/2W Film
CR3203,103-3304Diode, Low VoltageR322563-10836-68680 Ohm, +5% 2W Wire Wound
CRX3204103-308ADiode, Zener322663-10235-741.2K Ohm, +5% 1/4W Film
CR3205103-305Diode, DamperR322763-10235-802.2K Ohm, +5% 1/4W Fiim
CR3206103-2840Diode, Low VoltageRX3235,63-10810-081.2K Ohm, #1% 1/2W Film
R3207103-295-01ADiode, Low VoltageRX324053-10857-0410 Meg Ohm, +20% 1/2W Carbon
(used with 149-454)324263-10243-802.2K Ohm, +5% 1/2W Film
cR3208108-295-01ADiode, Low Voltage324363-10243-802.2K Ohm, +5% 1/2W Film
R3209103-142-01Diode, Low Voltage324463-7868100K Ohm, +5% 1/2W Carbon
CR3210103-142-01Diode, Low VoltageR326163-10444-86390 Ohm, +10% SW Wire Wound
R321103-142-01_Diede, Low Voltage326263-10565-65510 Ohm, +10% 1/2W Film
Qx3202121-975Transistor, NPNR326363-10565-65510 Ohm, +10% 1/2W Film
ax3204121-973Transistor, PNP, Shutdown328263-10235-9610K Ohm, +5% 1/4W Film
3206121-1037Transistor, NPN, Forward Driver
Qx3207121-975Transistor, NPN, Shutdown
3209121-1040Transistor, NPN, Reverse Driver

ZENITH MONITOR — SWEEP BOARD REPLACEMENT PARTS LIST

Page 96

a es Bo & @ mane Rene’ aa ( os 7 atl CS R340 ®

para je $i? ea 22K IK

+ mr OG 8) \u/ FRpae ;

I|'

con hicsaoa ae TS |

' { | f

|4Ling

23 {ape | gger bo 7! i} - 1

|cesoa——-tiB}|
i | etyaaToco Leet] caesecy
|1x0 foes jae IE! bee aot |
er2s01 |=ws

| =“ ®

ieo OREcolt

| ®

'|cxearI
|4 _nesor | pesos‘s7OMr

| @

1bord|

vw

  • —— 1 | 3201 S00" Df casah si meses | Feared | "] Fe petauieen iwyi ,
=\azn | SRMan '
|Bee |———
|i 1 |-—.Ji
|oy]£x3201||

Hl f \ T[rs202 > 4 tLe vie ET

a} aa a_ _ma_st a|

a Lot TUF 2 fia —— SF UO oo

| SCKEMATIC FOR 9 -227- RGB COLOR MONITOR (MAIN BOARD)

ZENITH RADIO CORP. C 9 CHICAGO. ILL 5-20 MO51-00087-A024_

Page 97

ZENITH MONITOR — MAIN BOARD REPLACEMENT PARTS LIST

Board Board 9-227 9-227

9-227-01Ref.No. PartNo.Description9-227-01Ref.No. PartNo.Description

RESISTORS RESISTORS (Continued)

xX—RX2101 63-10565-3222 Ohm, +5%, 1/2W FilmX251863-10235-731.1K Ohm, +5%, 1/4W Film
xXR210263-10243-56220 Ohm, +5%, 1/2W FilmxR251963-10235-937.5K Ohm, +5%, 1/4W Film
xXR210363-10235-88 4.7K Ohm, +5%, 1/2W FilmX251963-10235-822.7K Ohm, +5%, 1/4W Film
xX—RX2104 63-10243-113 Ohm, +5%, 1/2W FilmxR252063-10235-802.2K Ohm, +5%, 1/4W Film
xX—RX2105 63-10243-113 Ohm, +5%, 1/2W FilmxR252163-10235-50 120 Ohm, +5%, 1/4W Film
xX210663-10235-721K Ohm, +5%, 1/4W FilmX252163-10235-48100 Ohm, +5%, 1/4W Film
xXR210763-10235-66 560 Ohm, +5%, 1/4W FilmxR252263-10235-741.2K Ohm, +5%, 1/4W Film
xXR2108—63-10235-66 560 Ohm, +5%, 1/4W Filmx252363-10236-28 220K Ohm, +5%, 1/4W Film
XxXR210963-105651 Ohm, +5%, 1/2W FilmX—R252363-10236-52 2.2 Meg Ohm, +5%, 1/4W Film
xX211063-105651 Ohm, +5%, 1/2W FilmxX252463-10235-90 5.6K Ohm, +5%, 1/4W Film
xX211163-105651 Ohm, 5%, 1/2W FilmxR252563-10235-567
xX211263-105651 Ohm, +5%, 1/2W FilmX252563-10235-58 270 Ohin, +5%, 1/4W Film
xX211363-10243-60 330 Ohm, +5%, 1/2W FilmxR252663-10235-802.2K Ohm, +5%, 1/4W Film
xX211463-10235-721K Ohm, +5%, 1/4W FilmXP252663-10235-69 750 Ohm, +5%, 1/4W Film
xXR211563-10235-88 4.7K Ohm, +5%, 1/4W FilmxR252763-10857-315K Ohm, Control-Rotary
xXR211663-10235-60 330 Ohm, +5%, 1/4W FilmSing\e-Blue
xXR211763-10235-80 2.2K Ohm, +5%, 1/4W FilmXR252763-10857-26 800 Ohm, Control-Rotary
xX211863-10235-884.7K Ohm, +5%, 1/4W FilmSingle-Blue Cut-Off
xX211963-10235-54180 Ohm, +5%, 1/4W FilmxR252863-10857-301K Ohm, Control-Rotary
XxX212063-10565-082.2 Ohm, +5%, 1/2W FilmSingle-Yellow
xXP212163-10243-52150 Ohm, +5%, 1/2W FilmXR252863-10857-26 800 Ohm, Control-Rotary
xXR212263-10243-52150 Ohm, +5%, 1/2W FilmSingle-Blue Drive
xXR212563-9023-02550 Ohm, +20%, Control-xR252963-10235-76 1.5K Ohm, +5%, 1/4W Film
Rotary Single-GRAX252963-10235-751.3K Ohm, +5%, 1/4W Film
XR212663-10243-66 560 Ohm, +5%, 1/2W FilmxR253063-10235-93 7.5K Ohm, +5%, 1/4W Film
xR212663-10243-53160 Ohm, +5%, 1/2W FilmXA253063-10235-822.7K Ohm, +5%, 1/4W Film
X212763-10243-69750 Ohm, +5%, 1W Carbonx253163-10235-80 2.2K Ohm, +5%, 1/4W Film
xR212863-10243-66 560 Ohm, +5%, 1/2W FilmxR253263-10235-50120 Ohm, +5%, 1/4W Film
XR212863-6058510 Ohm, +5%, 1W CarbonX253263-10235-48100 Ohm, +5%, 1/4W Film
XP212863-10243-65 510 Ohm, +5%, 1/2W CarbonxR253363-10235-741.2K Ohm, +5%, 1/4W Film
xR250163-10236-28 220K Ohm, +5%, 1/4W Film253463-10235-52150 Ohm, +5%, 1/4W Film
X — R250163-10236-522.2 Meg Ohm, +5%, 1/4W FilmxR253563-10235-52150 Ohm, +5%, 1/4W Film
xX250263-10235-90 5.6K Ohm, +5%, 1/4W FilmxR253663-10235-52160 Ohm, +5%, 1/4W Film
x250363-10235-56220 Ohm, +5%, 1/4W FilmxR253763-10235-52150 Ohm, +5%, 1/4W Film
X250363-10235-58 270 Ohm, +5%, 1/4W FilmxR253863-10235-56220 Ohm, +5%, 1/4W Film
xR250463-10235-802.2K Ohm, +5%, 1/4W FilmX253863-10235-48100 Ohm, +5%, 1/4W Film
XR250463-10235-69 750 Ohm, +5%, 1/4W FilmxR253963-10235-56 220 Ohm, +5%, 1/4W Film
xR250563-10857-11_5K Ohm, Control-RotaryXR2539_63-10235-48100 Ohm, +5%, 1/4W Film
Single-REDxR254063-10235-56 220 Ohm, +5%, 1/4W Film
XR250563-10857-27800 Ohm, Control-RotaryX254063-10235-48100 Ohm, +5%, 1/4W Film
Single-Red Cut-OtiXR254163-10235-54 180.0hm, +5%, 1/4W Film
xR250663-10857-30_1K Ohm, Control-RotaryX254263-10235-53180 Ohm, +5%, 1/4W Film
Single-YellowX254363-10235-54180 Ohm, +5%, 1/4W Film
X250663-10857-27 800 Ohm, Control-RotaryX254463-10235-54180 Ohm, +5%, 1/4W Film
Single-Red DriveX254563-10235-54180 Ohm, +5%, 1/4W Film
xR250763-10235-761.5K Ohm, +5%, 1/4W FilmXR254663-10235-53160 Ohm, +5%, 1/4W Film
XR250763-10235-751.3K Ohm, +5%, 1/4W FilmXR254863-10235-67 620 Ohm, +5%, 1/4W Film
XR250863-10235-937.5K Ohm, +5%, 1/4W FilmX254963-10235-67 620 Ohm, +5%, 1/4W Film
xR250863-10235-822.7K Ohm, +5%, 1/4W FilmX — R255063-10235-32 22 Ohm, +5%, 1/4W Film
xR250963-10235-802.2K Ohm, +5%, 1/4W FilmX255263-10235-32 22 Ohm, +5%, 1/4W Film
xR251063-10235-50120 Ohm, +5%, 1/4W FilmX255463-10235-3222 Ohm, +5%, 1/4W Film
XR251063-10235-48100 Ohm, +5%, 1/4W FilmxXR320163-10235-59300 Ohm, +5%, 1/4W Film
xR251163-10235-74 1.2K Ohm, +5%, 1/4W FilmxX320263-10235-4468 Ohm, +5%, 1/4W Film
X251163-10235-67620 Ohm, +5%, 1/4W FilmxX320363-10235-52150 Ohm, +5%, 1/4W Film
xR251263-10236-28220K Ohm, +5%, 1/4W FilmxXR320563-7781820 Ohm, +5%, 1/2W Carbon
X251263-10236-522.2 Meg Ohm, +5%, 1/4W FilmxR3206F-1185112 Ohm, + 10%, 10W Resistor
xXR251363-10235-905.6K Ohm, +5%, 1/4W Film& Splice Assy.
xR251463-10235-56 220 Ohm, +5%, 1/4W FilmXR320663-10460-5012 Ohm, + 10%, 10W
X251463-10235-58270 Ohm, +5%, 1/4W FilmWirewound
xR251563-10235-802.2K Ohm, +5%, 1/4W FilmxX321063-10420-312 Ohm, +5%, 2W Wirewound
R251563-10235-71910 Ohm, +5%, 1/4W FilmxXR321263-10235-761.5K Ohm, +5%, 1/4W Film
xR251663-10857-32 5K Ohm, Control-RotaryxR321363-10235-83 3K Ohm,+5%, 1/4W Film
Single-GreenX—R3213_63-10235-86 3.9K Ohm, +5%, 1/4W Film
XR251663-10857-25800 Ohm, Control-RotaryxX321463-10235-741.2K Ohm, +5%, 1/4W Film
Single-Green Cut-Offx321563-10244-38 560K Ohm, +5%, 1/2W Film
xR251763-10857-301K Ohm, Control-RotaryX321563-10244-40680K Ohm, +5%, 1/2W Film
Single-YellowxXR321663-10244-25160K Ohm,+5%, 1/2W Film
X—R251763-10857-25800 Ohm, Control-RotaryxXR3217_63-10244-33_ 360K Ohm,+5%, 1/2W Film
Single-Green DrivexXR321863-10235-802.2K Ohm, +5%, 1/4W Filrn
xR251863-10235-761.5K Ohm, +5%, 1/4W FilmXR321963-10244-38 560K Ohm, +5%, 1/2W Film

MAIN BOARD (Continued)

Board

9-227Ref. No.Part No.Description
9-227-01Ref.No. PartNo.Descriptionee

== CAPACITORS

RESISTORS (Continued)c210122-7775-10A0.0088 MF, 100V +20% Polyester
xXR322263-10235-4047 Ohm, +5%, 1/4W Film,210222-7775-24A0.1 MF, 100V +20% Polyester
xXR323163-99821 Ohm, +10%, 2W WirewoundC210322-7709-09C100 MF, 35V +50%-10% Electrolytic
xXR323363-10565-14 3.9 Ohm,+5%, 1/2W FilmC210422-7613-24D0.01 MF, 50V +10% Disc
xXR323463-10565-143.9Ohm, +5%, 1/2W Film210522-7390-020.47 MF, 50V +20% Electrolytic
xXR323963-10244-20100K Ohm, +5%, 1/2W FilmC210622-7710-07C33MF, 50V +50%~10% Electrolytic
xXR324163-82464 Ohm, 10W WirewoundC210722-7615-03D0.0033 MF, SOV +80%—10% Disc
xXR324463-10840-40 47 Ohm, +5%, 3W Film,211022-7742-100.001 MF, 50V +10% Polyester
Tin OxideC211122-7774-17A0.027 MF, 100V +10% Polyester
xXR324563-10710AThermistorC217622-7725680 MF, 50V + 100%—10% Electrolytic
xXRX3246 63-10657-031.2 Meg Ohm, +20%,C250122-7621-42C220 PF, 50V +5% Disc
1/2W CarbonC250222-7621-42C =. 220 PF, 50V +5% Disc
XR326063-10243-96 10K Ohm, +5%, 1/2W FilmC250322-7621-42C220 PF, S0V +5% Disc
XR326163-10244-24150K Ohm,+5%, 1/4W FilmC320122-7775-24A0.1 MF, 100V +20% Polyester
X326263-10235-68 680 Ohm, +5%, 1/4W FilmC320422-76034.7 MF, 315V +100%—10% Eleciroiyiic
xXR340163-10236-461.2 Meg Ohm, +5%, 1/4W FilmC320522-35120.01 MF, 1KV +40%~20% Disc
xXR340263-10236-22120K Ohm, +5%, 1/4W FilmC320622-7603-01A10MF, 315V +100%-10% Electrolytic
xXR340363-10235-863.9K Ohm, +5%, 1/4W FilmC320722-7742-100.001 MF, 50V +10% Axial
xXR340463-19235-863.9K Ohm, +5%, 1/4W FilmC320822-7742-100.001 MF, 50V +10% Axial
xXR340563-10236-0833K Onm, +5%, 1/4W FilmC320922-7395,470 PF, SOOV +5% Disc
xXR340663-10235-68 680 Ohm, +5%, 1/4W FilmC323422-7395470 PF, 500V +5% Disc
xXR340763-10236-18 82K Ohm, +5%, 1/4W FilmC323622-7861-142200 MF, 35V +20% Electrolytic
xXR340863-10236-0422K Ohm, +5%, 1/4W FilmC324622-7603-01A10 MF, 315V +100%—10% Electrolytic
xX340963-10857-17100K Ohm, Control-RotaryC324722-7860-12470 MF, 25V +20% Electrolytic
Single-GreenC324922-7431-080.0047 MF, +20% Disc
xXR341063-10236-31300K Ohm, +5%, 1/4W FilmCX326022-7431-060.0047 MF, +20% Disc
xXR3411_63-10236-03 20K Ohm, +5%, 1/4W FilmC325122-78110.001 MF, 1KV +10% Disc
xXR341263-10236-13 51K Ohm, +5%, 1/4W Film.C325222-78110.001 MF, 1KV +10% Disc
xXR341363-10236-0730K Ohm, +5%, 1/4W FilmC325322-78110.001 MF. 1KV +10% Disc
xXR341463-10235-9812K Ohm, +5%, 1/4W FilmC325422-7404-0622 MF, 16V +20% Electrolytic
xXR341563-10236-0218K Ohm, +5%, 1/4W FilmC325622-7508-05B2200 MF, 35V +50%~10% Electro!
xXR341763-10243-60330 Ohm, +5%, 1/2W FilmC325722-7395470 PF, 500V +5% Disc
xX341863-10857-082K Ohm, Control-Rotary340122-7613-24D(0.01 MF, 50V +10% Disc
Single-YellowC340222-7406-011.0 MF, 35V +20% Electrolytic
xXR341963-10235-84 3.3K Ohm, +5%, 1/4W FilmC340322-7773-18A0.033 MF, 100V +5% Polyester
xXR342063-10236-10 39K Ohm, +5%, 1/4W FilmC340422-7773-17A0.027 MF, 100V +5% Polyester
xXR342163-10235-731.1K Ohm, +5%, 1/4\W FilmC340522-7775-10A0.0068 MF, 100V +20% Polyester
xXR342263-10243-60 330 Ohm, +5%, 1/2W FiimC340722-7710-01A1.0 MF, SOV +50%~10% Electrolytic
xX342363-10243-60 330 Ohm, +5%, 1/2W FilmC340922-7709-09C100 MF, 35V +100%—10% Electrolytic
xXR342463-10235-721K Ohm, +5%, 1/4W FilmC341022-7404-06A22MF, 16V +20% Electrolytic NP
xXR342563-10235-88 4.7K Ohm, +5%, 1/4W FilmC341122-7708-09100 MF, 25V +50%~10% Electrolytic
xX342863-10235-822.7K Ohm, +5%, 1/4W FilmC341222-7710-01C1.0 MF, 50V +50%—10% Electrolytic
xXR342963-10235-761.5K Ohm, +5%, 1/4W FilmC341322-7562-320.47 MF, 100V +5% Polyester
xXR343163-10235-802.2K Ohm, +5%, 1/4W Film341422-7774-16A0.022 MF, 100V +10% Polyester
xR343263-10235-55200 Ohm, +5%, 1/4W FilmC341922-7751-39180 PF, 50V +5% Axial
XR343263-10235-792K Ohm, +5%, 1/4W FilmC342022-7710-01C1.0 MF, SOV +50%-10% Electrolytic
xXR343363-10236-20100K Ohm, +5%, 1/4W FilmC342122-7773-18B0.033 MF, 100V +5% Polyester
xXR343463-10236-22120K Ohm, +5%, 1/4W FilmC342222-7613-24D0.01 MF, 50V +10% Disc
xXR343563-10235-63 430 Ohm, +5%, 1/4W FilmC342322-7613-08D470 PF, 50V +10% Disc
xX343663-10235-721K Ohm, +5%, 1/4W FilmC342422-7742-05390 PF, SOV +10% Axial
xX343963-10243-792K Ohm,+5%, 1/2W FilmC3425,22-7742-100.001 MF, SOV +10% Axial
xXR344063-10235-86 3.9K Ohm.+5%, 1/4W FilmC342622-7742-100.01 MF, 5OV +10% Axiai
xR344163-10857100 Ohm, Control-RotaryC342722-7647-35C150 PF, +10% Axial
Single-Horizontal CenterC342822-7774-120.01 MF, 100V +10% Polyester
X344163-10857-02250 Ohm, Control-RotaryC342822-7774-20A0.047 MF, 100V +10% Polyester

Singie-Horizontal Center (on-01 version)

xXR344263-10235-86 3.9K Ohm, +5%, 1/4W FilmC342922-7405-044.7 MF, 25V +20% Electrolytic NP
xR344363-10235-65 510 Ohm, +5%, 1/4W FilmC342922-74060.47 MF, 35V +20% Electrolytic NP.
XR344363-10235-80 2.2K Ohm, +5%, 1/4W Film(on-01 version)
xX344463-10235-60 330 Ohm, +5%, 1/4W FilmC343022-7613-24D0.01 MF, 50V +10% Disc
xXR344563-10235-802.2K Ohm, +5%, 1/4W FilmC343122-7774-16A0.022 MF, 100V +10% Polyester
XR344663-10235-721K Ohm, +5%, 1/4W FilmC343422-7742-06470 PF, 50V +10% Axial
xR344963-10235-761.5K Ohm, +5%, 1/4W FilmC343622-7613-24C0.01 MF, 100V +10% Dise
xR345163-10235-825%, 1/4W Film”C345022-7739-29A0.27 MF, 100V +10% Polyester
XR345163-10235-88 4.7K Ohm,+5%, 1/4W FilmC345022-7619-41C200 PF, 50V +5% Disc
xXR345263-10235-32 6.8K Ohm,+5° . 1/4W Film(on-01 version)_
XR345363-10235-751.3K Ohm, +5%, 1/4W FilmC346122-7710-01C1.0 MF, 50V +50%-10% Electrolytic
xXxR346163-1023615K Ohm, +5%, 1/4W FilmC346222-7710-01C1.0 MF, 50V +50%-10% Electrolytic
xXR346263-10236-1351K Ohm, +5%, 1/4W FilmC346222-7739-090.0056 MF, 100V +10% Polyester

(on-01 version)

346322-750847 MF, 35V +20% Electrolytic

5-21

Page 98

MAIN BOARD (Continued)

Ret. No.Part No.Description

SEMICONDUCTORS

CR2104103-142-01Diode, Low Voltage
CR2105103-254-01Diode, Low Voltage
CR2106103-254-01Diode, Low Voltage
CR2107103-254-01Diode, Low Voltage
CR2501103-142-01Diode, Low Voltage
CR2502103-142-01Diode, Low Voltage
CR2503103-142-01Diode, Low Voltage
CR3202103-330ADiode, Low Voltage
CR3205103-309-01Diode, Zener 10V 1W
CR3206103-254-01Diode, Low Voltage
CR3208103-3264,Diode, Low Voltage
CR3210103-254-01Diode, Low Voltage
CR3211103-254-01Diode, Low Voltage
CR3214103-284-ADiode, Low Voitage
CR3217103-326ADiode, Low Voltage
CR3219103-3304Diode, Low Voltage
CR3223103-330ADiode, Low Voltage
CR3224103-330ADiode, Low Voltage
CR3231103-315-06ADiode
CR3232103-315-06ADiode
CR3233103-315-06ADiode
CR3234103-315-06ADiode
CR3235103-284ADiode, Low Voltage
CR3401103-142-01Diode, Low Voltage
CR3404103-143-01Diode, Low Voltage
CR3405103-142-01Diode, Low Voltage
CR3406103-142-01Diode, Low Voltage
CR3408103-279-14Diode, Zener 6.8V 1/2W
2101F-10896Transistor & Heat Sink Assy.
Q2102F-10896Transistor & Heat Sink Assy.
Q2103121-975Transistor NPN
Q2104121-1064Transistor PNP
Q2501121-1019Transistor PNP.
Q2502121-895,Transistor NPN
Q2502121-551Transistor NPN

(on-01 version)

Q2503121-1019Transistor PNP
Q2504121-895Transistor NPN
Q2504121-551Transistor NPN

(on-01 version)

Q2505121-1019Transistor PNP
Q2506121-895Transistor NPN
Q2506121-551Transistor NPN

(on-01 version)

Q2507121-1019Transistor
Q2508121-1019Transistor
92509121-1019Transistor
Q3200F-12737Transistor & Heat Sink Assy.
Q3201121-499-01Transistor NPN Regular Feed Back
Q3202121-1034Transistor NPN
Q3203121-1059Transistor PNP
93401121-895Transistor NPN
Q3402121-986Transistor PNP
Q3403121-985Transistor NPN
Q3404121-895Transistor NPN
Q3405121-895Transistor NPN

TRANSFORMERS & COILS

L250220-3887-01Coil Peaking 1.2UH
L250320-3887-01Coil Peaking 1.2 UH
L250420-3887-01Coil Peaking 1.2 UH
L320120-2021Coil Peaking 100 UH
LXx320295-3501-01Transformer Choke 60 UH
1340120-3831Coil Peaking 663 UH
340220-3998Coil Peaking 39 UH
L340220-4026Coil Turnable 39 UH

(on-01 version) ZENITH MONITOR — CRT SOCKET BOARD

REPLACEMENT PARTS LIST

CRT SOCKET (9-155-10)

Ref. No.Part No.Description

CAPACITORS

C510122-46710.01 MF, 1.5KV, +80%-20% Disc
c510222-35120.01 MF, 1KV, +40%-10% Disc

TRANSFORMERS & COILS

510220-3887-28E220 MH Peaking
510320-3887-28E220MH Peaking
510420-3887-28E220MH Peaking

SEMICONDUCTORS

Q5101F7510Transistor, NPN, Video Out, Blue
Q5102F7510Transistor, NPN, Video Out, Red
Q5103F7510Transistor, NPN, Video Out, Green

RESISTORS

R510163-10840-884.7K Ohm, +5%, 3W Film
R510263-77851K Ohm, +10%, 1/2W Carbon
R510363-77851K Ohm, +10%, 1/2W Carbon
510463-10235-54180 Ohm, +5%, 1/4W Film

R5105 63-10235-48 — 100 Ohm, +5%, 1/4W Film

R510663-77851K Ohm, +10%, 1/2W Carbon
R510763-77851K Ohm, +10%, 1/2W Carbon
R510863-77851K Ohm, +10%, 1/2W Carbon
R510963-77851K Ohm, +10%, 1/2W Carbon
R511063-77851K Ohm, +10%, 1/2W Carbon
R511163-77992.2K Ohm, +10%, 1/2W Carbon
511263-10840-884.7K Ohm, +5%, 3W Carbon
R511363-10840-884.7K Ohm, +5%, 3W Carbon
R511463-10235-54180 Ohm, +5%, 1/4W Film
R511563-10235-54180 Ohm, +5%, 1/4W Film

MISCELLANEOUS

SA286-799Stake Connector 4/.156
5C286-799Stake Connector4/.156
5H386-799Stake Connector 2/.156
5X786-799Stake Connector 1/.312

A-10008 CRT Socket

5-22

Page 99

RESISTORS ARE 1/2HATT UNLESS OTHERWISE

NOTES: (USED WITH CIRCUIT REFERENCE DESIGNATORS P/L = SEE PARTS LIST FOR APPLICABLE USAGE. = JUMPER WIRE USED INSTEAD. = m © = PROVISION ON PRINTED CIRCUIT BOARD. | 9-155-10 | ' (204-960) |

' |

R5110

!1k|
|RS101,€5103I

4.7K i 34 A E5102 usi02 P5118 22 1K i | I ! | ot

  • +

RS111 04 345103 2.2K oO 22004, | I S113 $RS112

\Q5103)4.7K4\
Ls101pe hl3H

| + | 95102

!+121-1034 |

1 RED OUT | 1 esi02

  • c B01 = RSLS 180 \ 1744 }

RS114 We 1744 I

i

+156 CENTERS 5c2 5A2

|we|| Cecone|[ — rep
iaGREEN
|BASEeLuE

L140 voe ROUND

NOTE: 1.

<=)

{

RADIG LRF, HILAL Tee 5-23

Page 100

A-l0530 TO H.O.T. ASSY

fH ¢ 7 530 PF 3 530 PF

18-3059

Lo 1 ce | 530 PF 530 PF

TO 9-136-03 SWEEP MODULE

5-24

NOTE

WIRE M05 1-00087-A023 “HOLES #22GA. SCHEMATIC FOR A-IG539 WIDTH STEF ASSY.

ZENITH

RADIO CORP. CHICAGO, ILL. ISSUE

B A-|0530

Page 101

MAIN MODULE (SEE CHART) 3Vv3

oo

el, 363 ! a fooso ° [eeees} ie rs ren an [2 )0 303 : Le | panes

Pale °

3 x eouaca [eee

2AS 285 3F3 318 388 3RB [e200] [eeace] [ooo] 2 o| [eo =» «| [eo o 2A3

SWEEP MODULE

y TO DEGAUSSER Hl 22-7735-01

jo VIDEO OUT (SEE CHART)

SX3 | (SEE CHART)

383 3R3

oa ooo

  • ! 18) 7?

+

16 ;* *

T HV POWER poueeky SSEMBLY

YOKE (SEE CHART)

MID

AIR ?

27 | oa | | 383 (2)

H PCB £ * ASSEMBLY WIDTH STEP (SEE CHART) 63-10657-€3_

IMFURKTANT CAFETY NeTICe WHEN SERVIZING THIS CHASSIS. UNDER NC CIRGUMSTANCES “CHCULC THE ORIGINAL UE CLFIEC OR ALTEREL WITHOUT CN FROM THE ZENITH RACIC CCR- PORATICN. AL ZOMPONENTS SHOULO BE RE- PLACEC CNLY ALTH TYPES TUENTICAL TO THOSE IN THE ORIGINAL CIRCUIT. ANC TAL LOCATION, WIRING AND JET ENFORM TC ORIGINAL CMPLETIUN OF REFAIRS . THEIR 6H LEAL ORE! yout

PcpectaL CIRCUITS ARE ALSO SEL TO FREi VENT SHCZK ANC FIRE HAZARC, THESE AREAS | ARE SHAGEL ON THE SCHEMATIC FOR EASY ICENTIFIZATION. THE LETTER “X" INCLUDED “IN THE [TEM NUMBER Lt 3

| HIGH ARE REGIIREG TL MAINTAIN FORMANCE. NO-LEVIATIUNS ARE AL CAEL | WITHOUT ERTOR APPROVAL SY) THE PRUCEST | SAPETY ENGINEERING LEFARTMENT.

THIS CIRCUIT CIAGRAY. AYU SSAGTUNA: CIFFER FROM THE ACT IK. IRGUIT 1SEC. THIS WAY) IME-EMECTATION CE THE CATEST SAFETY AC FERFURMANCE IMPROVEMENT EWANGES INTC THE SEC Ic NOT OE. AYEL UNTIL. THE Hed SERVICE CITERAT the PRINTEL.

M051-00087-A025

INTERCONNECT FOR

1SSJE MONITOR

5-25

Page 102

VI. Self-Test Mode

The Self-Test mode is a special mode for checking game play statistics as well as game switches and computer functions. It is the easiest and best way to check for proper operation of the entire game.

NOTE: Putting the game into Self-Test WILL NOT cause the game to erase any CREDITS it has in its memory when the Self-Test mode is entered. You may begin a Self-Test at any time by sliding the Self-Test switch to the “ON” position after the power to the game is on (the Self-Test switch is located just inside the cabinet coin door frame as you face it). When this is done, the game will react as follows:
  • If the game is in the Attract mode when the Self- Test switch is moved to the “ON” position, it will finish the sequence and then go into the Self-Test mode. This is illustrated by the display of the Self- Test Mode Menue on the monitor screen.
  • If the game is in the Ready-To-Play mode or the Play mode when the Self-Test switch is slid to the “ON” position, it WILL NOT go into the Self-Test mode until AFTER the game is over. At this point, the game will go into the Self-Test mode. Again, this is illustrated by the display of the Self-Test Mode Menue on the monitor screen. . The fastest way to enter the Self-Test mode is to slide the Self-Test switch to the “ON” position and then activate the “TILT” switch located on the back side of the coin door just below the lock mechanism. The game will then IMMEDIATELY go into the Self-Test mode.

The Self-Test mode has eight (8) major categories as illustrated by Figure 6-1.

  • It is easy to select what category you wantto enter. By following the ON SCREEN instructions, the Cursor at the left of the screen can be moved UP or DOWN until it is in front of the category you want to test.
  • After the Cursor has been positioned, follow the ON SCREEN instructions again. and the monitor screen will display the test category you have selected.
NOTE:There is one exception to this. If you select the “PRE-SET” category on the Self-Test Mode Menue, EVERYTHING, | repeat — EVERYTHING
  • including ALL information in the “BOOKKEEP- ING” mode, and ALL operator selected options, will be set back to zero (“0”) and to the factory recommended settings — respectively.

6-1

SELEGT DESIRED TEST

2 SOUNDS 3 PLAYER INPUT 4 BOOKKEEPING 5 MACHINE SETUP 6 CHANNEL TEST T PRESET. 8 GRID DISPLAY

POSITION CURSOR BY...

Figure 6-1 Self-Test - Menue

O Once you are IN one of the Self-Test mode categories, FOLLOW THE ON-SCREEN IN- STRUCTIONS TO COMPLETE THE TEST.

  • The next group of Figures show the CORRECT screen presentation for EACH category of the Self-Test mode. During the SELF DIAGNOSTICS section of the Self-Test mode, you will first see a cross hatch pattern on the screen for about 1/2 second. Second, you will see a lot of different colored bars shown on the monitor screen. These bars will be UNpainted one at a time from the top down. Third, you will see the screen painted Red, Biue, and Green in bars from the top down. Fourth, ail the different colored bars you saw “Second” are displayed again. And fifth, the different colored bars are replaced by an exit message. If you do not exit, the test will repeat itself. This feature was designed into the game to enable over-night testing for an intermittent hardware problem. lf the SELF DIAGNOSTICS find one or more bad ROM or RAM chips: instead of going through what is described above, the game will give you a written message as to which parts are bad. This message includes their |.D.’s and their P.C. Board locations.
Page 103

During the SOUNDS section of the Self-Test mode, the game will give a display which looks like that shown in Figure 6-1a. C In this category, each of the game’s separate sounds can be checked individually in any order — or — you can tell the game to check them all in order. During the PLAYER INPUT section of the Self-Test mode, the game will give a display which looks like that shown in Figure 6-1b. C In this category, each of the game's player operated controls — including the coin switches on the back side of the coin door — may be checked individually. A game sound will be heard as each switch/control is actuated. If no game

SELECT A SOUND 1 ALL SOUNDS

REMAINDER OF

GAME SOUNDS

CALLED QUT IN ORDER

POSITION CURSOR BY...

Figure 6-1a Self-Test - Sounds

PLAYER INPUTS

PLI FIRE

ate Device activated is spelled out inthe space

MINI UPRIGHT 1 COIN METER

ACTIVATE ALL PLAYER INPUT SWITCHES AND DEVICES HIT TILT 10 EXIT

Figure 6-1b Self-Test - Player Inputs sound is heard, that switch/control is either not working, miswired, or disconnected, Check it out thoroughly. During the BOOKKEEPING section of the Self- Test mode, the game will give a display which looks like that shown in Figure 6-1c. In this category a basic bookkeeping function is performed. And with the selection of the “TIME REPORT” and the “SCORE REPORT”, detailed breakdowns of game times and scores may be obtained. In the TIME REPORT and SCORE REPORT sections of the BOOKKEEPING mode, the game will give displays which look like those shown in Figures 6-1d and 6-1e respectively.

SELECT A REPORT OR EXIT _ CHUTE 1 COINS CHUTE 2 COINS LONGEST GAME SHORTEST GAME HIGHEST: SCORE 05 18 00 43 86310 LOWEST SCORE 120 TIME REPORT

SCORE REPORT

EXIT POSITION GURSOR BY...

Figure 6-1c Self-Test - Bookkeeping

TIME REPORT 0 1030 SEC 30 7060 SEC 60 10 90 SEC 90 T0 120 SEC 120 TO 150 SEC 150 T0 180 SEC 3704 MIN 4705 MIN 5 10.6 MIN OVER 6 MIN

Figure 6-1d Self-Test - Time Report

6-2

Page 104

SCORE REPORT 0 TO 5000 PTS © 5000 TO 10000 PTS 10000 T0 20000 PTS 20000 TO 40000 PTS” 40000 T0 70000 PTS 70000 TO 100000 PTS 100000 TO 150000 PTS 150000 TO 200000 PTS 200000 TO 250000 PTS OVER 250000 PTS

Figure 6-1e Self-Test - Score Report During the SETUP OPTIONS section of the Self- Test mode, the game will give a display which looks similar to that shown in Figure 6-1f. O In this category, all common game options may be changed from the contro! console: coins per credit, credits per base, bonus hase(s) awarded at, difficulty level - -, and so on.

SETUP OPTIONS

COIN CHUTE 1 *1 COINS FOR *T GREDITS

COIN CHUTE 2 “1 COINS FOR *Y CREDITS

“1 CREDITS FOR “3 BASES TST EXTRA BASE AT *20000 POINTS

ADDITIONAL BASE EVERY - *20000 POINTS

*3 DIFFICULTY LEVEL

  • = Factory recommended settings. Figure 6-1f Self-Test - Set-Up Options

DIFFICULTY LEVEL EXPLANATION: The Difficulty Level setting has a range of 1 to 9. With 1 being the easiest level of play and 9 being the most difficult level of play. We recommend that a setting of 3 be used as a beginning point. Game play can then be made MORE difficult or LESS difficult, according to the skill levels attained by the players in your area. CHANNEL TEST: During the CHANNEL TEST section of the Self- Test mode, the game will give a display which looks like that shown in Figure 6-tg. O In this category, the game conducts a test of its SOUND SYSTEM. Once you enter the CHANNEL TEST section of the Self-Test mode, the game automatically tests Channels 1 through 6 giving a tone for each one as it checks it. After the 6th Channel is tested, the game automatically repeats the test until exited. It then goes back to the Self-Test Mode Menue. During the GRID DISPLAY section of the Self-Test mode, the game shows a white cross hatch pattern on the monitor screen. This is for alignment and/or test purposes. This pattern will remain on the monitor screen until exited. The game will then go back to the Self-Test Mode Menue. To leave the Self-Test mode, simply slide the Self-Test switch to the “OFF” position at ANY time. The game will then run through the ROM/RAM test display after which normal game functions will return to the monitor screen.

CHANNEL TEST CHANNEL 1

CHANNEL 2

CHANNEL 3 CHANNEL 4 CHANNEL 5

CHANNEL 6

Figure 6-1g Self-Test - Channel Test

RACK ADVANCE: The game can be made to advance through the various racks by beginning a game and THEN sliding the Self-Test switch to the “ON” position. After this has been done, each time you depress the ONE PLAYER BUTTON the game will advance one rack. When you reach the desired rack, slide the Self-Test switch to the “OFF” position. (If you leave the Self- Test switch in the “ON” position, the game will go into the Self-Test mode when you are finished playing.)

Page 105

CROSS HATCH PATTERN: A cross hatch pattern is shown on the screen when power is first turned on to the game, when the TILT. Switch is actuated, and during the “SELF DIAGNOS- TIC” portion of the Self-Test mode, and during the “GRID DISPLAY” portion of the Self-Test mode. This pattern may be kept on the screen for adjustment purposes as described earlier. When you are finished using the cross hatch pattern, simply exit at the GRID DISPLAY to return to the Self- Test Mode Menue. HARDWARE MASTER RESET SWITCH: There are two of these little red switches, one on the Sound I/O Board and one on the CPU Board, located as shown in Figure 6-2. The function of each of these switches — when pressed — is to make the game think it has JUST been turned on. They set up an “initial power-up” condition. We DO NOT recommend that you indiscriminately press EITHER of these switches. They should ONLY be used if there isa major problem encountered while testing the P.C. Boards.

HARDWARE MASTER RESET SWITCH

Figure 6-2 Location of Hardware Master Reset Switch

6-4