Asteroids Deluxe DP-165-2nd-02B
Asteroids Deluxe (rev 3) (Atari, 1980) · Drawing Package · 1 pages · original scan

INPUTS
PLAYER INPUT CIRCUITRY
sor ment [i
<7 ponte a test point
OPTIONS INPUT CIRCUITRY
VIDEO INVERTER
‘Sheet 2, Side B
‘The x- and y-video inverter circuits are identical;
fore, only the x-video inverter circult is explained. For invertered video operation, pin 19 is grounded which turns fon transistor Q13 and tums off transistor Q12. In this state INV is +8.2 VOC and NONINV is -82 VOC.
For a noninverted video output, pin 19 is unconnected and floats. In cocktail games, pins 19 and 7 are shorted and have a potential of +5 VOC. This causes transistor 13 to be cut off and transistor Q12 to be tumed on. INV Is then 2 VDC and NONINV is approximately +82 VOC. In upright games, only the x-video inverter is used. In
cocktail games both x-and y-video inverters are used, and
In cabaret games video Inversion is not necessary, 80 neither is used
DP-165-02 2nd printing
OUTPUTS
DIAG STEP (diagnostic step), KH, SELF-TEST SLAM, HALT, FIRE, and SHIELDS inputs are read ‘by the MPU when {Switch input zero enable) is iow. ‘Switches to be read are selected |, by ABO thru AB2 from the MPU. inputs are read on OB7. Switch inputs are active when pulled to ground. DIAG STEP, 3 Hz, and SELF-TEST are signals read by the MPU to initiate and Control the game's sel-test pro ‘cedure. SLAM is a signal read by the MPU to indicate the status cof the anti-siam switch mounted fon the coin door. The MPU reads HALT to determine the state of the vector generator. The coin door and some control panel switches are read by the MPU when SINPT (switch input one enable) is low. Switches to be read are ‘lected by ABO thru AB2 from the MPU. All inputs are read on data line DB7. Switch inputs are “on” when pulled to ‘ground, IW determines the direction of data flow (0B0:D87) as addressed by ABO-AB3. When FW is high, the MPU reads the Input data from DIP switch LB. When RIW is low, the MPU rites the audio 1/0 instruction for an output. The 62 input from the MPU is. the operating frequency for the ‘audio VO chip and sets the tim- Ing for data bus lines DBO-DB7.
When PKYDCD, AB10, and ABIt are high and ABB is low, ‘a chip select pulse is gated to the audio 1/0 chip. This pulse prepares the audio 1/0 for ‘The game option switches operation. ‘The Custom Audio chip M7/8 generates most of the sounds for Asteroids Deluxe".
are read by the MPU when ‘OPTS (option switch enable) is low. Switch toggles to be read are ‘selected by ABO and ABI from the MPU. Switch toggles 41, 3, 5 and 7 are read on data line DBO and toggles 2, 4,6 and 8 are read on DBI. Toggle inputs are “on” when pulled to ‘ground.
oro
oes fo alZ emu beso expaves 062 —Shso snes exravos, ke
<7] denotes a test point
cme exPLOSNO
‘The EXPLODE sound Is peard when any object explodes. Noise is. sampled at a frequency determined by P7, and control bits EXPITCHO and EXPITCH1. Changing the sampling rate changes the pitch ofthe ex plosion. The noise is ampliude- Modulated in RS by EXPAUDO- EXPAUDS,
re
snermnusten—p
[RB and P8 generate random noise. This noise is filtered by P11 and produces the tumble sound heard when the ship is thrusting, LAMP, LED, AND COIN COUNTER OUTPUT
<i ® oir com
Bou >
- al op senesin 15V
VIDEO OUTPUTS
Deenotes change by indicated revision <= penotes a test point This circuit consists of coin counter drivers 08, (29, G10 and data latch M10, clocked by the micro. computer's address decoder. When the input to a driver is clocked high, its collector goes low, grounding the return of the coin counter in the coin door. When START! or START2 is clocked low, it grounds the START LEDs in the control panel
‘The video-output circuit consists of three individual circuits: Xaxis, Y-axis, and Z-axis. The X-axis and Y-axis video-output circuits each consist of a digtal-to-analog converter (DAC), current-to-voltage converter, two sample and holds, and amplifier. The Z-axis, Video-output ci X and Y Outputs ‘The DACs (011 and 811) each receive binary numbers from the vector generator’s pos: tion counter outputs. These numbers represent the location of the beam on the monitor. For the nominverted X axis, the numbers range from 0 to 1023, where Ois atthe far lett of tthe monitor screen, $12 atthe center, and 1023 is atthe far right. For the non-inverted ¥ axis, the numbers range from 128 to 996, where 128 Is at the bottom of the monitor screen, 512's at the center, and 996 is at the top. When the X axis and Y axis are inverted, the monitor picture is tumed upside down. This is used for a two-player cocktail game: ‘The DACs convert these binary number inputs to current outputs. The DACs! current ‘outputs are applied to the pin-6 inputs of current-tovoltage converters C12 and A12. From the current-o-voltage converters, the signal is fed to two sample-and hold circuits: ‘One is non- inverted and the other is inverted. The non-inverted sample and hold consists ‘of one stage of analog switch D12 and capacitor C89 forthe X axis, and B12 and C109 for the Y axis. The inverting sample and hold consists of inverter E12, one stage of analog switch D2, and capacitor C88 for the X axis and BICI2, B12 and CHO for the Y axis ‘The sampleand.hold circuits are controlled by SHCON (sample and hold contro}. 'SHCON is derived by gating 3 MHz from the microcomputer clock circultry and VGCK* from the vector generator's state generator. The result of these inputs insures that the rnor-inverted and inverted analog signals that are applied tothe analog switches have sutficiently stabilized before being applied to the sample-and-hold capacitors.
‘The output swing of SHCON Is ~8 to +8 VOC. When SHCON is high, the voltage: charges or discharges the sample-and-hold capacitors to the X and Y analog voltage value. The voltages are then applied to the inputs of the second analog switch. These Switches select either the non inverted or inverted X-axis and Y-axis outputs. The outputs are then amplified by the second stages of C12 and A12 for an impedance-matched outbut to the X and ¥ inputs to the monitor. Since the monitor doesn't have fieldadjustable X and Y gains, the gains are adjustable by variable resistors F120 and R128. Z Output ‘The Z-axis video output receives six inputs. BVLD (beam valid), from the output of the vector generator’s position counters, tells the Z axis to draw the line. BLANK (vector ine blank), trom the vector generator’s state machine, tells the Z axis to stop drawing alin. SCALEO thru SCALES (grey-level shading scale), from the output of the vector generator's data latch, tells the Z axis the grey-level shading of the line that is being drawn on the monitor. ‘When BVLD and BLANR are both high, a high is clocked through shift register K9 that turns transistor Q3 off. This allows the scale inputs to be passed through transistor Q2. When '90es low, a low is clocked through K9, transistor Q3 tums on, and the ‘signal Is grounded at the base of transistor U2. The scale inputs at the base of transistor Q1 determine Q1's emitter voltage, during the line draw period. The SCALEO thru SCALES resistors R96 thru R39, resistor R35, and resistor R40 resuit in arange of about + 1.0 VOC when all are low and + 4.0 VDC when all are high. The emitter of Qt follows at about + 1.7 to 4.7 VDC, while the emitter of transistor @2 follows at about + 1.0 to 4.0 VDC. This output is applied to the Z input of the Imoitor Since hes ae bightnes and cnet controls inthe mono, here a6 no a justments in this crcut.
omer
Sheet 2, Side B
ASTEROIDS DELUXE™ Switch Inputs, Coin Counter, LED and Audio Outputs
© 1081 Ata ne.