CATHODE RAY TOMES

VS Atari RBI Baseball TM-321 1st Printing

Atari R.B.I. Baseball (Atari Games, 1987) · Technical Manual · 8 pages · 14 sections · original scan

Page 1

™312 Ist printing

VS.—PAK

A.

ATARI

GAMES

Atari R.B.I. Baseball

Installation Instructions for VS. UniSystem and VS. DualSystem

Licensed for play on the VS. System by NINTENDO

Page 2

Atari Games Customer Service

If reading through this manual does not lead to solving a maintenance or repair problem, call TELEHELP® at this Atari Games Customer Service office:

Parts and Service Atari Games Corporation California Customer Service Office 737 Sycamore Drive P.O. Box 361110 Milpitas, CA 95035 Fax (408) 434-3945 Telex 5101007850 [Ov (408) 434-3950 (Monday-Friday, 7:30~4:00 pm Pacific Time)

Copyright © 1987 Atari Games Corporation. All rights reserved.

en Contents of Pak:

R.B.I. Baseball Sub Board Assembly R.B.1. Baseball Sub Board Mounting Hardware PPU Read-Only Memory Kit Attraction Decat Glass Attraction Shield (DuaiSystem) Plexiglass Actraction Shield (UniSystem) Attraction Side Decals (DualSystem) Attraction Strip Decals (UniSystem) Cardboard Header R.B.1. Baseball Installation Instructions Game Options Label

Page 3

Atari R.B.1. Baseball Installation Instructions

Introduction

This Pak contains parts to change any VS. UniSystem or VS. DualSystem game. Please be sure to save your PPU ROM kit and literature from the VS. game you are converting so you can change back to that VS. game if you so desire. By doing this, you will be able to build a library of games for your VS. Systems. Tools needed: Small flathead screwdriver Medium Phillips-head screwdriver Staple gun Scotch tape

VS. Upright Pak Installation C. Remove the four top trim screws and top tim

Procedures (see Figures 2 and 3). . D. Slide the old attraction shield up and out of the I. New Style Attraction Decal game (see Figures 2 and 3). A. Adhere the attraction side decals or attraction E. Replace the attraction shield and top trim. Be sure strip decals to the back of the plexiglass or glass that the attraction shield fits under plastic center attraction shields as shown in Figure 1. trim, and that the left and right sides are correct.

VS. UniSystem™ VS. DualSystem™

ATTRACTION SIDE DECALS

ATTRACTION STRIP DECALS

PLEXIGLASS

SHOWN: VS. UniSystem

Figure 1

B. Using Scotch tape (not provided), tape new attraction decal to the back of either UniSystem NOTE plexiglass or DualSystem glass, depending on Do not tighten top trim screws until next step. which game the pak is being installed in first.

I. Cardboard Header

NOTE A. Fold the cardboard header and slide it under the

This new header system allows the same attraction de- top trim. cal to be moved between UniSystem plexiglass and DualSystem glass an unfimited number of times. B. Tighten the top trim screws (see Figures 2 and 3).

Page 4

Installation Instructions Atari R.B.I. Baseball

CARDBOARD CARDBOARD

HEADER HEADER

ASSEMBLED ATTRACTION SHIELD

Figure 2

TIL. Installing the R.B.I. Baseball Sub PCB Software 3. Insert the PPU into the 40-pin DIP IC socket at A. For VS. DualSystem (Two Monitors) location 3A on the Sub PCB, with the chips in . . . the same direction as the other ICs on that

  • If the R.B.I. Baseball is to. be installed in the board. main (left) side of the cabinet, then remove the 4. Bend down the capacitors C3, C11, C30 and existing the PPU and CPU chips (2403) at locations 2F and 2} on CPU PCB, and existing EPROMs in locations 1A, 1B, 1C, 1D, 2A, and C47. This will prevent contact with the bottom of the Sub PCB, which could cause a short cir- 2B. For Sub (right) side, use locations 8F and 8], aati. and EPROMs in locations 6A, 6B, 6C, 6D, 8A, 5. Firmly insert the R.B.I. Baseball Sub PCB into and 8B. the two empty 40-pin DIP IC sockets on the CPU PCB, Use locations 2F and 2} for the main.
  • Insert the CPU chip 2A03 into the 40-pin DIP (left) side or 8F and 8} for the Sub (right) side, IC socket at location 3B on the Sub PCB, with the chips in the same direction as the other ICs on that board.

SW1 comesponds to this program, MAIN (Loft side for wo monitor game- Nat used tor ane monitor game}

Page 5

Atari R.B.I. Baseball

CAUTION Be sure to insert the Sub PCB with the chips in the same direction as the other ICs on the CPU PCB. Inserting this Sub PCB backwards may damage both the CPU PCB and the Sub PCB.

B. For VS. UniSystem (One Monitor)

  • R.B.1. Baseball Sub PCB must use locations 8F and 8] (Sub side).
  • Follow the instructions for the right side installation in the DualSystem above.

Iv. Game Options Label A. Staple the label on the back door next to the old label.

NOTE Do not remove the old label!

B. Check the DIP switch settings on the PC board so they match the factory-recommended settings on the Game Options Label. Installation Instructions

V. Monitor Adjustments On many VS. systems, the monitor adjustments for vertical size and horizontal size are incorrectly set. When a misadjusted game is converted to R.B.I. Baseball, it is likely that two problems will occur:

  • Ifthe horizontal width is incorrect, the players’ names will not be completely visible. To correct this, adjust the horizontal width and position so that all six letters of the batter's and pitcher’s name are visible. Do this adjustment when the game is displaying the batter at the plate.
  • Ifthe vertical height is incorrect, the edge of the playfield may display meaningless pictures. Adjust the height so that the catcher’s head and shoulders are visible. Do this adjustment when the game is displaying the batter at the plate.

|. Final Checklist The FCC door is installed correctly. The attraction shield is installed correctly with the side or strip decals in place. The DIP switches are set correctly (see the Game Options Label for this game). All play buttons and controllers function correctly. The color on the monitor is correct. oog

The dispiay size adjustments are correct. gqgqgaq a

The coin acceptors give credit.

Page 6

Installation instructions

Game Play

Introduction

Atari R.B.1. Baseball is a two-player competitive (simultaneous) or a one-player against the computer game. As the ultimate action/strategy sports game, players select one of ten ‘Dream Teams”’, each with a roster of baseball greats. Like team managers, players put baseball savvy and knowledge on the line. In addition to playing skills, knowing the strengths and weaknesses of teams and players is crucial. It’s like real baseball because skill characteristics and statistics are based on actual player performance. An on-screen display gives game players the inside story. Atari R.B.L Baseball

Operating Modes

Atari R.B.I. Baseball has three operating modes: attract, play, and scoreboard.

The game begins by player(s) selecting the “Dream Team” of their choice and pressing Button A. In oneplayer or two-player competition, players may be required to insert coins to complete the entire game. A oneplayer game automatically ends at the point when the computer takes the lead. Game players use an eight-way joystick and two buttons, A and B. Both the joystick and the buttons perform different functions when “at bat” and “in the field.” Either start button can be used as 2 “timeout” button.

At Bat

Joystick:

  • Batter in the batter's box
  • Move joystick in any direction to shift batter's position in the batter’s box Base-running: point the joystick in the direction of the nearest base desired. Simultaneously press Button B to advance runner to the next base. Press Button A to return the runner to the previous base.
NOTE Once a runner has reached the next base, he can no longer be returned to the previous base. Button A:
  • Swings the bat at the ball
  • Returns the runner to the previous base (in base-running mode)

Button B:

  • Advances the runner to the next designated base (in base-running mode)
  • Causes the runner to steal (in batting mode)

In the Field Joystick:

  • Selects the type of pitch to throw © Determines the direction or curve of the pitch after the ball is released by the pitcher. ¢ Determines the pursuit direction of fielders
  • Makes the base selection by fielders. Simultaneously press Button A to throw the ball to the selected base, of press Button B to run the player with the ball to the selected base.

Button A:

  • Activates the pitch ¢ Activates throwing the ball from the fielders to the selected base

Button B: ® Commands the fielder to run with the ball to the selected base

  • Commands the pitcher to turn and “check” the base runner. The pitcher can then press Button A while simultaneously pointing the joystick at the selected base to throw the ball for a “pick-off” attempt.
Page 7

Atar! R.B.i. Baseball

Additional Features

Pinch Hitter:

  • Press either the Start 1 or Start 2 button; Time will appear on the game screen. © The team at bat can press Button A for pinch hitter roster.
  • Identify the choice with the joystick. © Make the selection with Button A. Installation Instructions

Relief Pitcher:

© Press either the Start 1 or Start 2 button

® Press Button A to see the relief pitcher roster. Identify the choice with the joystick.

  • Make the selection with Button A.
Page 8

Warranty

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays and laser video disc players (in games supplied with displays and video-disc players) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller's sole tiability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided: () Seller is promptly notified in writing upon discovery by Buyer that said products are defective; .

  • Such products are returned prepaid to Seller’s plant; and (©) Seller’s examination of said products discloses to Seller's satisfaction that such alleged. defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages. Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms berein, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neitber assumes nor authorizes any other person to assume for the Setler any other liabilities in connection with the sale of products by Seller.

AL ATARI GAMES The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to ensure your safety. Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari Games Corporation cannot be responsible for the quality, suitability or safety of any u10n-Atari part or any modification including labor which is performed by such distributor.

Atari Games Corporation 675 Sycamore P.O. Box 361110 Milpitas, California 95035