CATHODE RAY TOMES

Lizard Wizard

Lizard Wizard (Techstar (Sunn license), 1985) · Manual · 16 pages · 25 sections · original scan

Page 1

Conversion Kit Instruction

Manual

INTERNATIONAL INDUSTRIES, INCORPORATED

135 Mingo Trail * Longwood, Florida U.S.A. 32750 © (305) 834-7734

Page 2

Item #

14*

  • Optional
  • PARTS LIST -

Description

Auxiliary Logic Board Module

Lizard Wizard Program Roms

Lizard Wizard Character Roms

Lizard Wizard Bi-Polar Color Proms

Marquee Overlay

Control Panel Overlay

Side Panel Graphics

8 Way Joystick

Button/Switch Assemblies

Joystick/Button Hookup Wires

8" Tie Wrap

Instruction Manual

Phillips Wood Screws to Mount Auxiliary Module Wooden Control Panel, Unassembled, Predrilled Holes.

Page 3

LIZARD WIZARD

CONVERSION PROCEDURE

The following steps should be followed to convert your Pac Mac/ Ms. Pac Man

game to Lizard Wizard.

Main Logic P.C.B. Removal:

1.) Disconnect the Main Game Logic Board from all its cabling.

2.) Remove the P.C.B. clamps and slide the Main Game Logic Board out of the cabinet.

DISCONNECT

CABLING

DISCONNECT CABLING

MAIN LOGIC P.C.B.

REMOVE CLAMP TO P.C.B. OUT

REMOVE CLAMP TO SLIDE P.C.B. OUT

UPRIGHT

Page 4

3.)

4.) Cut the plastic securing strap and remove the "PIGGY-BACK" module. IF YOUR GAME IS EQUIPPED WITH ONE. if it IS NOT equipped with one, simply proceed to Step 4 below.

CUT PLASTIC STRAP AND LIFT SMALL P.C.B. (PIGGY BACK) OFF OF MAIN BOARD

Remove the Z-80 CPU from the Main Game Logic Board. BE CAREFUL NOT TO BEND ITS PINS!! Return this CPU to your stock. It may be used as a spare part.

Page 5

5.) Remove the six EPROMS and 2 PROMS located as shown below and set them aside. BE CAREFULL NOT TO BEND THEIR PINS!!. Replace the removed EPROMS and PROMS with the ones supplied in your conversion kit.

REMOVE (6) EPROMS AND REINSERT NEW EPROMS SUPPLIED WITH KIT. (LOCATIONS 5, 5F, 6E, 6F, 6H & 6J)

REMOVE (2) PROMS.

IMPORTANT!
NOTE LOCATION AND REINSERT NEW | OF NOTCH ON PROMS SUPPLIED | ALL LC.s REMOVED WITH KIT. (LOCATIONS 4A & 7F) | BEFORE INSERTING
Page 6

6.) Plug the ribbon extension cable for the Auxiliary Game Logic Board into the empty socket on the Main Game Logic Board that was left when you removed the 2-80 CPU from it in Step 4. Connect the Black wire from the module to ground.

USAC) = Pm a ray

INSERT RIBBON CABLE INTO SOCKET AS SHOWN

7.) If your game is equipped with a "PIGGY-BACK" module that you removed in step 3 reinstall it at this time. If it was not equipped with one, simply proceed to Step 8. Reinstall 8" tie wrap to secure the "PIGGY-BACK" module (do not tighten the tie wrap until the board is tested.)

REINSTALL “PIGGYBACK” MODULE TO MAIN P.C.B.

NOTE LOCATION OF NOTICES IN I.C.’s
Page 7
  • Reinstall the Main Game Logic Board and the Auxillary Game Logic Board (now attached to it by the ribbon cable) back into the game cabinet. Auxiliary Board should be attached to cabinet with wood screws provided.

INSTRUCTIONS FOR USING EXISTING MIDWAY CONTROL PANEL

1.) Disconnect control panel harness from main harness and remove control panel.

2.) Unsolder wires to Joystick (these will be used on the new first player joystick) and remove joystick.

3.) Remove the Pac Man / Ms. Pac Man overlay and apply Lizard Wizard control panel overlay.

4.) Locate and drill new joysticks & lazer button holes. See Drawing "C" (A helpful tool in cutting the holes in the metal control panel is a Greenlee Tool Company punch type 730, 1 5/16").

5.) Install kit buttons & Joysticks as shown in drawing "B".

Note: Joysticks require eight (8) carriage bolts with nuts & star washers. Size- 10-24 x 1".

6.) Solder the wires from the Midway control panel harness to the same connections on the first player joysticks.

7.) Connect the ground (common) side of all the switches with the black wire provided to the Red wire (common) from the original harness.

8.) Solder the six (6) pre-cut & pre-terminated wires provided to the appropriate switch. Insert in Wire Color Function connector #

Green /Black/White2nd Player Up12
YellowwooDownVv
Violet/Black/White"ooLeftP
Blue/Black/WhiteuoRight13
Orange/Blue/White=LazerR
Orange/Whitelst Player LazerTest Switch

9.) The wires that terminate in Amp Edge card terminals plug directly into the Midway connector as listed above. The wire without a terminal (Orange/White) must be soldered to what was the test switch input.

A.) Remove the White/Yellow wire from the test switch located just inside & to the right of the coin door.

B.) Solder the Orange/White wire from lst player lazer to the White/Yellow wire. Insulate your solder splice.

Page 8

Instructions for Optional Control Panel

A wooden control panel is available to ease your conversion of Pac Mac/ Ms. Pac Man to Lizard Wizard.

The new control panel utilizes the following items from your original Midway panel:

1.) Harness 2.) Mounting Pins (2) 3.) Latch Clamp Catch (2) 4.) k'" hex Screw (8) 5.) Start Buttons, Pal Nuts, Switches & Mounting Bracket (2)

Assembly:

1.) Properly position control panel overlay onto new dash and affix via

2.)

3.)

4.)

5.)

6.)

7.)

8.) pressure sensitive backing.

Cut Joystick Mounting holes thru overlay with sharp knife or razor knife.

Install mounting pins and latches in the precise position as on your original Midway control Panel. See drawing "A".

Unsolder wires from Midway Joystick.

Remove Midway start buttons from original panel with harness and install in the new panel. Solder the wires from the Midway harness to the same connection on the lst player Joystick. (See wiring diagram)

Install kit buttons and joysticks as shown in drawing "B".

Connect the ground (common) side of all the switches with the black wire provided to the red wire (common) from the original harness.

Solder the six (6) pre-cut & pre-terminated wires provided to the appropriate switch. The wires that terminate in AMP EDGE CARD TERMINALS plug directly into the Midway connector as listed below.

Page 9

INSERT IN

WIRE COLOR FUNCTIONS CONNECTOR #

Green/Black/White2nd player Up12
Yellow2nd Player DownVv
Violet/Black/White2nd Player LeftP
Blue/Black/White2nd Player Right13
Orange/Blue/White2nd Player LazerR

9.) The Ist Player Lazer uses the included Orange/White wire and must be tied to what was the Test switch input.

A.) Remove the White/Yellow wire from the test switch located just inside and to the right of the coin door.

B.) Solder the Orange/White wire from lst Player Lazer to this White/ Yellow wire from the test switch. Insulate your solder splice.

‘MARQUEE

Preparation:

1.) The Marquee artwork should be affixed to a piece of clear plexiglass measuring 23" x 9 1/16" x 1/8".

2.) A second piece of plexiglass measuring 23" x 9 1/16" x 1/16" should be placed on top of the other plexiglass to "sandwich" the artwork between them.

INSTALLATION

1.) Turn the power off

2.) Remove the screws from the top marquee bracket.

3.) Remove the Midway marquee

4.) Install Lizard Wizard marquee and replace top bracket and screws.

Page 10

LIZARD WIZARD DIP SWITCH TABLE

METHOD OF PLAY

sw #1 sw #2

OFFON2 COIN1 PLAY
ONOFF1 COIN2 PLAY
OFFOFF1 COIN1 PLAY

ON ON FREEPLAY

NUMBER OF SPACEMEN PER GAME

sw. #3 sw. #4

ONON5 SPACEMEN
OFFON4 SPACEMEN
ONOFF3 SPACEMEN
OFFOFF2 SPACEMEN

BONUS SPACEMAN

sw. #5 SW. #6

ONONBONUS SPACEMEN AT150,000
OFFONBONUS SPACEMEN AT125,000
ONOFFBONUS SPACEMEN AT100,000
OFFOFFBONUS SPACEMEN AT75,000

SW.#7 sw. #8

OFFOFFPLAY MODE
ONOFFROM & RAM TEST
OFFONLOCKS PICTURE
Page 11

Lizard Wizard Conversion Kit

Miscellaneous Information you may want to know:

1.) The front glass measures 23" x 21 1/8" x 3/16". If you replace this with plexiglass, use either clearor Light Smoke #2412.

2.) The Marquee glass measures 23" x 9 1/16" x 3/16".

3.) The cabinet color is Sun Yellow #30912

4.) The carriage bolts used to mount the joysticks are #10-24 x 1".

5.) I£ you make your own control panel, the holes are as follows:

  • Joystick Center = 1 3/16"
  • Joystick Mounting = 3/16"
  • Button Mounting = 1 3/16"

6.) An attractive monitor bezel is available from Wico Corp., Chicago, Ill. 60678

as: Universal Bezel Display #26-3157-00 @ $11.95

7.) A helpful tool in cutting the holes in the Midway metal control panel is a Greenlee Tool Company punch type 730, 1 3/16".

8.) A monitor bezel is also available from J-S Sales Company, Mt. Vernon, New York, 1-800-431-2944, catalog # 8063.

Page 12

SNOILISOd HOLVI

GNV Nid ONILNNOK

Page 13

lst PLAYER START

2nd PLAYER JOYSTICK

“SA

2nd PLAYER START

2nd PLAYER LAZOR

“

lst PLAYER JOYSTICK lst PLAYER LAZOR

™s!A

™s

BUTTON AND JOYSTICK POSITIONS

6)

Page 14

3 3/4" a 1

1 3/16"

u2/€ 9 3/16" DIA.

NOTE: AFTER JOYSTICK HOLES

HAVE BEEN DRILLED, ALIGN

JOYSTICK SWITCH ASSEMBLY

WITH HOLE AND MARK MOUNTING

HOLES BUTTON AND JOYSTICK

HOLE LOCATIONS

Page 15

YELLOW/RED

[ GREEN/ BLACK/WHITE BLUE/WHITE A

WHITE/RED WHITE/YELLOW

ORANGE/WHITE? <>) 1st PLAYER LAZOR/ TEST

SWITCH SPLICE let PLAYER

START — E eure —_____—_——oUP oe i |r H

lst PLAYER TEFT 2nd PLAYER LEFT RIGHT

LAZOR e @ — wazor —l— 2nd PLAYER ac Py + lst PLAYE! RIGHT ° . JOYSTICK ‘Ko

° wo] of

JOYSTICK e

° 2nd PLAYER

START

  • ae L ° °° Le eo

bow DOWN VIOLET/BLK/WHITE ORANGE/ BLUE/WHITE

YELLOW

COMMON L os 4 + + + > + + BROWN/WHITE BLUE/ BLACK/WHITE CONTROL PANEL WIRING DIAGRAM

Page 16

Pek a fai e Cr reat a Gea et ie ra eT as)

ERDKRSKSK KeKEKOROROXSKORORES bod td

RORSHKSKROROREROR

aha KERSH REO ‘a ome B _ SUNN INTERNATIONAL INDUSTRIES, INC.

LIMITED WARRANTY

Company warrants that the equipment will be free from defects in material and workmanship and meet product specitications tor a period of 60 days fron the date that purchaser accepts delivery of the equipment.

THIS WARRANTY DOES NOT COVER

  • Misuse or damage by Purchaser or a third party, Purchaser shall promptly report such defects to Company upon discovery, Company, at its option, shall either repair or replace such defective part or the entire item.
  • Damage caused by neglect, abuse, improper operation, improper repairs, accidents or damage caused by lire, food, acts of God or other casulatics beyond the control of Sunn International Industries Ine. (SUNN).
  • Game components or parts thereof which have had the identifying names and/or numbers removed, ultered, defaced or rendered illegible.

4, Components or parts not manufactured, installed, sold or authorized for use by SUNN, or modifications to game not authorized by SUNN. Use of such components, parts or modifications voids this Warranty in its entirety.

  • In transit damage claims must be filed with the carrier by the Purchaser.

This Warranty is in lieu of all other warranties, guaranices or agreements whether expressed or implied. No other person, agent, authorized service center or company is authorized to change, modify or extend its terms in any manner whatsoever.

SERIA! NO, se eee peer ee Ee oe Ee

MODEL NO.

DATE SHIPPED 0 en Ses Fee rene seer

TO: SUNN. Fill out this stub coniplerely and mail within ten (10) days. Please type or print. Detich stub from warranty and return,

NAME: a errr ee ee ye oe Ss

ADDRESS: 2 a

DATE SHIPPED: 0.

ZIP: CITY: 2 .. STAT

SERIAL NO. 2000. MODEL, NO. eee ees ee LE Ten Pit

Shak ROK teohies