Soccer TM-144 1st Printing
Atari Soccer (Atari, 1980) · Technical Manual · 44 pages · 34 sections · original scan
@ ATARI
We, Operation, Maintenance
and Service Manual
Complete with Illustrated Parts Lists
GAME SERIAL NUMBER LOCATION
Your game's serial number is located below the white team control panel on the outside of the game. The same number is also stamped on the chassis of the TV monitor, game PCB and Regulator/Audio PCB. Please mention this number whenever calling your distribution for service.
TV MONITOR
GAME PCB
REGULATOR/AUDIO PCB GAME SERIAL # IDENTIFICATION TAG
Operation, Maintenance and Service Manual
Complete with Illustrated Parts Lists
Published by: ATARI INC 1265 Borregas Avenue P. O. Box 427 Sunnyvale, California 94086
Copyright © 1979 by Atari, Inc. All rights reserved
No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission fram the publisher.
Lithographed in the U.S.A. 9H A Warner Communications Company
Table of Contents
Location Setup A. New Parts 1 B. Game Inspection 3 C. Game Installation. . 3
- Voltage Selection ....... 3
- Interlock and Power On/Off 3
- Game Fuses .... 5 D. Self-Test Procedure 5 E. GamePlay ....... 8
- Attract Mode.... 8
- Ready-to-Play Mode ‘ . 8
- Play Mode ... 0... cece ccc cece erence eter ene eneee 8
2 Maintenance and Repair A. Cleaning...... _ 9 B. Fuse Replacement... - 10 C. Opening the Game Top ......... . 10 1, Trak Ball™ Maintenance and Repair 11
- Pushbutton Switch Replacement. . -. 12
- TV Monitor Removal .......... -. 13 D. Printed Circuit Board Replacement 214 —. Game Operation................00085 Gag até seat ee s gee 15
Illustrated Parts Lists
List of illustrations
Figure1 OverviewofGame............. 2... e cece cece eee nee 2 Figure 2 Installation Requirements . . 3 Figure 3 PowerSupply.............. 4 Figure 4 Interlock and Power On/Off Switches 4 Figure 5 —_ Location of Self-Test Switch, Volume Control and Option Switches . 5 Figure 6 — Self-Test Procedure 6 Figure 7 Option Switch Settings . 7 Figure 8 Openingthe Game Top ...... . 10 Figure 9 Trak Ball™ Maintenance and red . 11 Figure 10 Pushbutton Switch Replacement . 12 Figure 11 TV Monitor Removal 13 Figure 12 Game and Regulator/Audio PCB Replacement . 14 Figure 13 Power Distribution - 15 Figure 14 Signal Distribution - 16 Figure 15 Final Assembly.... . 18 Figure 16 Hinges, Latches and Monitor Shield . 20 Figure 17 Control Panel Assembly ....... 21 Figure 18 Trak Ball™ Assembly . . 22 Figure 19 Steering Board Assembly . wi . 24 Figure 20 Power Supply Assembly for Raster- ‘Scan Games . 26 Figure 21 Regulator/Audio PCB Assembly ........... . 28 Figure 22 Soccer Game PCB Assembly - 30 Figure 23 Main Harness and Component Assembly. . . : Vena seer ea aeeee 34
If reading through this manual does not lead to solving a certain maintenance problem, call Tele-Help™ at the Atari Customer Service office in your geographical area, as shown in one of the two maps below. Order all parts from the California office.
WEST and CENTRAL U.S.A.
Parts for all Atari Customers. Sales and Service.
Atari Coin-Op Customer Service 1344 Bordeaux Drive, Sunnyvale, CA 94086 Telex 17-1103 (Monday - Friday, 7:30 - 4:00 pm Pacific Time)
s From California, Alaska or Hawaii (408) 745-2900
= From anywhere else in this area toll-free (800) 538-1611
EAST U.S.A. Sales and Service Only
Atari Inc. New Jersey Customer Service Oftice Cottontail Lane, Somerset, NJ 08854 Telex 37-9347 (Monday - Friday, 8:30 - 5:00 pm Eastern time)
From New Jersey s (201) 469-5993
From anywhere else in this area toll-free (800) 526-3849
Location Setup
A. New Parts
The Atari Soccer™ game has two new parts. If you have worked on Atari video games in the past, then you should be aware of these important differences. The new parts are described below and shown in Figure 1.
« Power Supply Assembly. It covers a wider voltage range than before, has higher reliability, a smaller overall size, and all fuse numbers and fuse amperages are marked directly on the metal chassis.
© Regulator/Audio PCB. Most of the heatproducing components have been moved off the garne PCB and onto this smaller board, so the parts will not be prone to a higher rate of failure.
Throughout this manual and the illustrated parts lists, wherever one of these two parts is mentioned, you will see this symbol in the page margin:
BEZEL
TV MONITOR OFFSIDE SWITCH
2.OR 4 PLAYER SWITCH L/ TRAK BALL™ CONTROL
SPEAKER LA
COIN DOOR POWER ON/OFF SWITCH
POWER CORD
REGULATORI/AUDIO PCB “> ACCESS PANEL POWER SUPPLY
Figure 1 Overview of Game
B. Game Inspection
This new game is ready to play upon removal from the shipping carton. However, your careful inspection is needed to supply the final touch of quality control. Please follow these steps to help us insure that your new game was delivered to you in good condition.
- Examine the exterior of the game cabinet for dents, chips, or broken parts.
- Unlock and open the access panel of the cabinet and inspect the interior of the game as follows: a. Check that ali plug-in connectors (on the game harness) are firmly seated. b. Remove the game printed circuit board (PCB) as follows: e Remove the screws at the edge of the PCB closest to you. e Unplug the edge connectors carefully. DO NOT BEND THE PCB.
- Slide the PCB out of its slots. c. Verify that all integrated circuits (ICs) are firmly seated in their sockets or soldered in place. You should eliminate any foreign material such as loose bits of wire or solder splashes that could cause unwanted conductive paths. d. Note the location of the game’s serial number—it is on the metallic label in the upper left corner on the side of the cabinet. A serial number (not necessarily the same one) also appears in the corner of the back side of the game PCB. A drawing of this is on the inside front cover of this manual. Please mention this number whenever you call your distributor for service. e. Carefully slide the PCB back into its slot in the game cabinet and secure with the two screws at the board’s edge closest to you. f. Plug the edge connectors back onto the PCB. DON’T FORCE THEM. The connectors are keyed so they will only go on in the proper orientation. A reversed edge connector will damage the PCB.
- Check all major subassemblies such as the power supply, loudspeaker (which contains powerful magnets that will attract small metal items—remove these items), and all Player-operated controls and switches. Check that the video monitor is securely mounted; if necessary, tighten the monitor mounting hardware.
C. Game Installation
Figure 2 Installation Requirements Power 110 VAC, 60 Hz (nominal), 120 watts OR 220 VAC, 50 Hz (nominal), 120 watts Temperature 0 to 38°C (32 to 100°F) Humidity Not over 95% relative Space Required 75 x 135 cm (292 x 53 in.) Game Height 94 cm (37 in.)
- Voltage Selection "> Before plugging in your game, make sure that the voltage selection plug on the power supply (see Figure 3) is correct for your location’s line voltage. Check the wire color on the plug and see if it is correct per the list below.
Line Voltage Range Voltage Selection Plug Color
90-110 VAC (100) Violet 105-135 VAC (120) Yellow 200-240 VAC (220) Blue 220-260 VAC (240) Brown
- Interlock and Power On/Off Switches To minimize the hazard of electrical shock while you are working on the inside of the game cabinet, two interlock switches have been installed (see
POWER INPUT
VOLTAGE SELECTION PLUG
SAFETY \_
INTERLOCK
Figure 4 Interlock and Power On/Off Switches
Figure 4). One is located behind the access panel and one is behind the coin door. These switches remove all the AC line power from the game circuitry when a door is opened.
Check for proper operation of the interlock switches by performing the following steps:
- Unlock and open the access panei and the coin door.
- Plug the AC line power cord into an AC outlet. Set the on/off switch to its on position.
- Close the access panel and coin door. Within approximately 30 seconds after closing the panel and door, the TV monitor should display a picture.
- Slowly open the rear access panel. The TV Monitor picture should disappear when the panel is opened to approximately 2.5 cm (1 inch). Close and lock the access panel, and repeat this step with the coin door.
- If the results of step 5 are satisfactory, the interlock switches are operating properly. If the TV monitor doesn’t go off as described, check to see if the corresponding interlock switch is broken from its mounting or stuck in the on position.
- Game Fuses Fuse locations and values are marked on the power supply chassis beneath the fuse protective
SELF-TEST SWITCH
VOLUME DECREASE: TURN CLOCKWISE insulation (see Figure 22). For continued protection of your game, as well as for the safety of the players. fuses must be replaced only with identically rated ones.
Information on the TV monitor fuses is printed in the TV monitor manual that has been supplied with your Atari Soccer game.
D. Self-Test Procedure
This game will test itself and provide data to demonstrate that the game’s circuitry and controls are operating properly. The data is provided on the TV monitor and the game speakers: no additional equipment is necessary.
Part of the self-test procedure includes the adjustment of the game’s volume and a display of the operator-selected game options. Therefore, we suggest yourun the self-test anytime you need to adjust the volume or change the options. Besides, this method will eliminate an inaccurate coin count, which would occur if the coin switch wire was tripped merely to change the volume level during game play.
To run the self-test, follow the instructions outlined in Figure 6.
OPTION SWITCHES
Ny
Figure 5 Location of Self-Test Switch, Volume Control and Option Switches
Figure 6 Self-Test Procedure
| INSTRUCTION | RESULTS IF TEST PASSES | RESULTS IF TEST FAILS | |
| 1. | Memory Check | TV monitor displays ROM OK RAM | TV monitor displays ROM BAD, RAM |
| Set self-test slide switch | OK message at top of screen (see | BAD, or nothing at all. |
to on position (see self-test display in Figure 7). Figure 5).
Offsides and 2 or 4 player switches Either or both switches do not light. light.
| 2. | Moving Display Check Dark gray center portion of TV mon- | TV monitor display does not move. |
a. Press left Kick Button _ itor display moves toward Black team on Black team end of end of game. game.
| b. Press right Kick But- | Dark gray center portion of TV mon- | TV monitor display does not move. |
ton on Black team end of _ itor display moves toward White team game. end of game.
The following test checks not only the Trak Balls but also the motion RAM. The TV monitor displays 16 arrows. Each Trak Ball moves four arrows. One arrow for each Trak Ball moves at a time in the same direction as the Trak Ball’s movement. To move the second set of arrows, press any game switch while moving the Trak Ball. Release the switch to move the third set of arrows. Press any switch while moving the fourth set of arrows. The picture in Figure 7 shows the 16 arrows all moved in two rows.
| 3. | Trak Ball and Moving | All 16 arrows move in same direction | One or more arrows don’t move at all |
| Object Check | of Trak Ball’s mcvement. | or don’t move in same direction of |
Roll each Trak Ball as Trak Ball’s movement. explained above.
| 4. | Switch Test | Crowd sound heard while each | No crowd sound heard for one or |
| Activate all game | switch is active, | more switches. |
switches including coin trip wires and coin door slam switch.
Audio Adjustment
Activate any game switch and adjust the game sound level as desired.
Option Switch Selection
Immediately below the ROM OK message line on the TV monitor display are three lines of numbers that indicate the settings of the 8-toggle DIP switch on the game PCB. Figure 7 shows what these numbers represent and how to select the option of your choice. Figure 5 shows the location of this option switch, as well as the 4-toggle DIP switch that changes the TV monitor display language.
Figure 7 Option Switch Settings
To change toggle positions of the switch assemblies, you need not remove the game PCB. The switches, usually colored blue, are easily accessible when the PCB is mounted in piace. When changing the options, verify proper results on the TV monitor display during self-test.
Toggle settings of 8-toggle switch
| on game PCB | Option | TV Monitor Display During Self-Test | |||||
| 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 |
OFF OFF OFF 4:00 per credit N fe] OFF OFF ON _ 3:30 per credit T OFF ON OFF _ 3:00 per credit U Three digits of first line
| Ss | OFF ON ON _ 2:30 per credit | immediately below ROM |
E OK message (picture below
| D | ON OFF OFF | 2:00 per credit | indicates time setting of |
4:00 per credit) ON OFF ON 1:40 per credit
ON ON OFF _ 1:20 per credit
ON ON ON 1:00 per credit
| ON | Left coin mech | Second digit of second line |
multiplied by 1 beiow ROM OK message
| OFF | Left coin mech | (picture below indicates 2 |
multiplied by 2 time credits per coin).
ON ON Right coin mech N multiplied by 1
| fe) | ON OFF | Right coin mech | Third digit of second line |
| T | multiplied by 4 | below ROM OK message |
| OFF ON | Right coin mech | (picture below indicates 5 |
| U | multiplied by 5 | time credits per coin). |
| $s | OFF OFF | Right coin mech |
E multiplied by 6 D ON 1 coin minimum > Single digit in third line below ROM OK message (picture below
| OFF | 2 coin minimum | indicates 1 coin minimum). |
§ ae
| Toggle setting of 4- | 8 | 68 |
| Position switch on | ry | t 5 |
game PCB Language 8 ze
2H 3:
| 4 | 3 | 2 | 1 | ay | 38 |
| NN | ON ON | English | RE | Zé | |
| O | O | ON OFF _ | German | Bo | Ed |
| T | T OFF ON | French | as] | ome |
OFF OFF Spanish gee Seco
| voy | eae | aS |
DD
E. Game Play
The Atari Soccer™ game has four modes of operation: attract, ready-to-play, play, and self-test. Selftest isa special mode for checking the game switches, Trak Balls, and computer functions. You may enter this mode from any of the other three modes. If you enter it from the play mode, all time credit is cancelled.
- Attract Mode The attract mode begins when power is applied to the game, after the play mode, or after self-test. This mode is continuous and is only interrupted when one game is paid for and accepted, or if you activate the self-test. In this mode, the unit demonstrates game play as the computer controls both teams displayed on the monitor. The computer displays messages to potential players on each end of the screen. When players have paid for one game and the coin register has accepted the coins, the play mode begins. If the two-coin-minimum option is selected, the ready-to-play mode won't begin until the second coin is accepted.
- Ready-to-Play Mode The ready-to-play mode begins when time for one game is paid and accepted by the coin register. This mode lasts for ten seconds or until one of the offensive team members displayed on the monitor has touched the ball. However, during the first three seconds of this mode, the displayed members of both teams automatically move to their starting positions, then large arrows appear on the monitor to show which Trak Balls control which team members. At the end of the three seconds, you will hear the game whistle, and the Trak Balls are enabled. At this point, play may begin or the players may use the additional time to select the offside rule or a 4-player game. The play mode begins when anyone touches the ball or at the end of ten seconds.
- Play Mode The play mode begins at the end of the ready-toplay mode. This mode lasts until three seconds after the game timer reaches 00. Players may buy extended time any time during this mode. The Offside Rule and 2 or 4 player select switches are both active and you may press either one to change game play. When thirty seconds remain on the game timer, the monitor flashes the video message GAME ALMOST OVER and you will hear a whistle. When fifteen seconds remain, you will hear the whistle again. From the time of the whistle until time runs out, the crowd audio will sound as if the crowd were counting down the seconds. At zero seconds you'll hear three whistles, and all action on the monitor freezes. If players don’t purchase additional time within three seconds, the game returns to the attract mode.
Maintenance and Repair
The Atari Soccer™ game requires certain maintenance to keep it in good working order. Clean, properly maintained games attract players and earn more profits.
The most important maintenance item is running the self-test every time you collect money from the cash box. Just looking at a game will not tell you if switches are broken, whether parts in a Trak Ball are defective (such as only one direction of motion working), whether the audio is set correctly, or if bulbs have burned out. The self-test wil! inform you of any of these possible problems.
Second, you should regularly clean the outside of the game and the coin mechanisms. In addition, you will need to regularly lubricate ali the Trak Ball controls: for details see this chapter.
A. Cleaning
The exterior of the game cabinet and the glass and acrylic surfaces may be cleaned with any non-abrasive household cleaner. if desired, special coin machine cleaners that leave no residue can be obtained from your distributor.
The inside of the monitor shield has been silkscreened; be careful when cleaning this surface to avoid damaging the paint. The large monitor shield is made of tempered glass and should be scratch resistant.
B. Fuse Replacement C. Opening the Game This game contains six fuses—all on the power Top
supply assembly (not including the TV monitor fuses). Replace fuses only with the same type as Prior to repairing or replacing any component listed below. See the TV monitor manual for the on the game top or prior to removing the TV monitor fuse data. monitor, unplug the game. Then open the coin door. F1, F2, F3 7-amp. 250V 3AG slow-blow glass cartridge-type fuse Reach through the opening and unlock both luggage-style latches above the coin door (see F4, F5,F6 3-amp. 250V 3AG slow-blow glass Figure 8). Lift up the game top and tilt it away cartridge-type fuse from you. The two gas springs will hold the top up. Do not jam the game top up against its top- The metal power supply chassis is marked with most position — this is hard on the gas spring all six fuse numbers and amperages. Figure 20 mounting hardware. shows the power supply in detail, including top and bottom views.
LUGGAGE-STYLE LATCH
Figure 8 Opening the Game Top
- Trak Ball™ Maintenance and Repair
To maintain this control, you will only have to Periodically lubricate the bearings as described on the Trak Ball’s small label. Use only 2 drops of 3-in-One® oil in each of the ball bearings. Do not overlubricate, as this causes oil to flow onto the shafts and the ball. The resuliing slippage means players on the screen can be moved only with great effort. In addition, the oiled ball will cause player aggravation.
For further instructions on how to replace the Trak Ball or either steering PCB, see Figure 9.
Trak Ball™ Control Removal © Open game top as illustrated in Figure 8.
- Unplug the control panel harness connector.
- Remove eight carriage bolts from the control panel. See © in this figure.
- Lift out entire control panel as shown by direction of arrows.
- Remove three carriage bolts from Trak Ball assembly. See ®. Remove the Trak Ball assembly.
Ball Replacement
- Remove three countersunk machine screws from the Trak Ball assembly’s acrylic top plate. (When the assembly is installed, these three screws are right underneath the control panel.) See @.
- Remove and replace the ball. See @.
Figure 9 Steering PCB Replacement
- Unplug conne ‘on steering PCB. Remove two crossrecessed machine screws, associated washers and hex nuts from the steering PCB. See ©,
- Remove the steering PCB. See ©.
- When replacing this PCB assembly, be certain that the black toothed wheel turns freely between the two halves of the red photo sensor device. Trak Ball™ Lubrication
- Open game top as illustrated in Figure 8.
- Unplug the contro! panel harness connector. ight Allen-head screws from the contro! panel. this figure.
- Lift out entire control panel as shown by direction of arrows. Place the panel on a flat surface, so it lies upside down.
- Apply only 2 drops of 3-in-One® oil in each of the ball bearings. (Each Trak Ball control has five bearings.) Turn the panel over and roll the balls in all directions. Be sure the oil has not spread onto the shaft:
- Reinstall the control panel, and plug the control panel harness connector back together again.
Trak Ball™ Maintenance and Repair
"1
To remove LED switch on top of game:
2. Pushbutton Switch e fet multimeter to Rx 1 ohms scale, then zero
je meter.
Replacement
. a . . @ Connect multimeter leads to appropriate The two light-emitting diode (LED) switches on switch contacts. (See Figure 10 for designatop of the game and the four kick switches have tion of switch contacts.) a very low failure rate. In case a switch should ever be suspect, first test it per the description @ Check contacts (push and release the switch that follows. To replace the switch, refer to Figure button) for closed and open continuity. 10. | @ If the contacts do not operate sharply or @ Remove the wires from the suspected switch. always remain closed or open, then replace the switch.
To remove kick switch on side of game:
- Disconnect the control panel hamess connector; then remove the control panel.
- Remove the harness wires from the faulty switch.
- Turn the switch counterclockwise. The silver-colored bezel on the outside should not turn, due to the
presence of the lock washer and nut. Sie Are
¢ Install a new switch using the reverse procedure. (NO)
- Reconnect the harness wires on the switch; then reinstall the control panel. wonwanuy = CLOSED O) (N.C.) CONTACTS
COMMON , CONTACT -LIGHT-EMITTING DIODE (L.E.D.) CONTACTS
2 = NORMALLY OPEN \ (N.O.) CONTACT S X) d
NORMALLY CLOSED (N.C.) CONTACT
L.E.D SWITCH: TO REMOVE TURN COUNTERCLOCKWISE
Remove all wires from the faulty switch. Turn the switch counterclockwise while holding the black cone-shaped molding on the outside of the control panel. Install a new switch using the reverse procedure. Reconnect the harness wires.
Figure 10 Pushbutton Switch Replacement
- TV Monitor Removal
High voltages exist in any television unit, even with power disconnected. Use extreme caution and do not touch electrical parts or the TV yoke area with your hands or with metal objects in your hands! If you should need to service or replace the 23-inch TV monitor, you must first remove it from the game cabinet. To avoid possible back strains you should have a helper assist you in this procedure. Follow the instructions in Figure 11.
High voltages exist in any television unit, even with power disconnected. Use extreme caution and do not touch electrical parts or the TV yoke area with your hands or with metal objects in your hands!
Open the game top as described in Figure 8. Be sure the game Is unplugged. Unplug the TV monitor harness connector. Remove the eight TV monitor wood screws and tie-down brackets. Then remove the two carriage bolts, wing nuts and miscellaneous washers on the TV’s metal chassis. With the help of another person, if possible, lift the monitor assembly up and out of the game.
Figure 11. TV Monitor Removal
D. Printed Circuit Board Replacement
You may wish to remove the game printed circuit board (PCB) or the Regulator/Audio PCB for service or inspection. To do this, refer to Figure 12 and proceed as follows:
1.
2. Open the side access panel. Be sure the game’s power is off. Locate the securing screws and fiber washers that hold down the PCB in its slots, and remove them (two screws and washers for each PCB). If you are removing the game board, first remove the four machine screws that hold the edge connectors to the small black connector mounts, along the game PCB’s edge. Then unplug the edge connectors on game PCB. If you are removing the Regulator/Audio PCB, simply
a REGULATOR/. AUDIO PCB
Figure 12 > > disconnect the three small harness connectors on this board. Carefully slide either PCB straight out of its slots. Be careful not to twist the board, as this may loosen connections or components. Replace or repair as required. Reinstall the PCB, making sure that the connectors are properly plugged in. Note they are all keyed to fit on only one way, so if they don’t slip on easily, don’t force them! A reversed connector will probably damage your game and will void the warranty. Replace the securing screws and fiber washers in the PCB. Reinstall the machine screws into the black connector mounts on the PCB. Close and lock the side access panel. Check that the option settings of game PCB are as you desire, and perform the self-test. This is especially important with any game when you replace a PCB.
SOCCER GAME PCB
Game and Regulator/Audio PCB Replacement
E. Game Operation
With this manual you received two large sheets that contain the wiring and schematic diagrams for Atari Soccer. Sheet 1, Side A, includes an index that shows the arrangement of these diagrams. These diagrams include information that explains the functions of the circuits and defines inputs and outputs.
Atari Soccer is a microcomputer-controlled game. The microcomputer is contained on the game PCB. The game PCB receives inputs from the two small PCBs on each Trak Ball, from each kick button, the offsides rule and 2 or 4 player switches, and the coin door switches. All these inputs are processed by the game PCB and output to the TV monitor and the Regulator/Audio PCB.
TRAK BALLS
COIN DOOR
GAME INTERLOCK SWITCHES
REGULATOR/AUDIO PCB J cunt we a
POWER CORD. (
w= The Regulator/Audio PCB performs two functions: 1) regulates the + 10.3 VDC from the power supply to +5 VDC, and 2) amplifies the audio from the game PCB. The +5 VDC from the Regulator/ Audio PCB provides all power for the game PCB, excluding the game PCB’s audio amplifier. The audio from the Regulator/Audio PCB directly drives both game speakers and is controlled by the volume control mounted inside the coin door.
The Power Supply is the source of all voltages in the game. These voltages are protected by six fuses located on the top of the power supply chassis.
Figure 13 illustrates the distribution of power in this game. Figure 14 illustrates the distribution of signals.
TV MONITOR a <a. OFFSIDES &2 AND 4 PLAYER Rw ee SWITCHES Se
TRAK BALLS—> a>
aN
420 VAC [F 2st
As a | GAME PCB <2
a POWER SUPPLY we
Figure 13 Power Distribution
TV MONITOR
BLACK TEAM WHITE TEAM TRAK BALLS BLACK TEAM TRAK BALLS. RIGHT KICK BUTTON
WHITE TEAM
KICK BUTTONS 2.0R 4 PLAYER SWITCH
OFFSIDES SWITCH Fi
wi RULE LED TWO4 LED
SPEAKER _ 6 H Ss e
°
=
TEAM 1 TRAK BALL INPUTS
TEAM 2TRAK BALL INPUTS
COIN DOOR
GAME PCB
BLACK TEAM LEFT KICK LEFT BUTTON “> REGULATOR/AUDIO PCB
Figure 14 Signal Distribution
Illustrated Parts Lists
The purpose of this chapter is to provide you with the necessary information for ordering replacement parts for your Atari Soccer™ game. Please note that, for simplicity, common hardware has been deleted from most of these parts lists. This includes screws, nuts, washers, bolts, etc. When ordering parts from your distributor, give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.
@ earn S @ co ® (4 0a \ ern Sp pA
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproduction, toridcen without INe Specific written permission of Alar, the.,” Sunnyvale California. This drawing rs only conditionally (saved, and einer receipt nor posseasrn thereat confers ansters right invor 3 Srawing or any thereon, nor any right fo reproguce tis drawing sr ay Dart tereot- except for manufacture by vendors ol Alar Ineor porated ord for manutature une ha corporaton's writ fer 2, no right to reproduce this Urawing is granted forthe subject matter thereo! unless by witten agreement wih or written perznission Irom tne corporation
NOTES: Q\ For safety, green wires (labeled GND) must be attached to metal bracket or chassis.
A After reinstalling control panel or Trak Ball, attach ring of ground strap, using existing screw in hinge. Staple ground strap in place, bending braid to conform to cabinet.
Figure 15 Final Assembly A035110-XX A
Figure 15 Final Assembly Parts List
| Item | Part No. | Description |
| 1 | A035103-xx | Hinges, Latches and Shield—see Figure 16 |
| 2 | A035105-01 | Control Panel Assembly—see Figure 17 |
| 4 | A035107-01 | Access Panel Assembly |
| 5 | A034560-01 | Power Supply Assembly for Raster-Scan Games—see Figure 20 |
| 6 | A034485-01 | Regulator/Audio PCB Assembly—see Figure 21 |
| 7 | A034905-01 | Soccer Game PCB Assembly—see Figure 22 |
| 8 | A030268-01 | Cash Box Assembly |
| 9 | A034841-03 | Strain Relief Power Cord Assembly (domestic) |
or A034863-03 Strain Relief Power Cord Assembly (European)
| 10 | A034974-01 | Gas Spring Mounting Assembly |
| 1 | A035194-01 | Main Harness and Component Assembly—see Figure 23 |
| 13 | A034031-02 | Ground Strap |
| 14 | A021084-01 | Voltage Selection Plug, 100V (other plugs available are listed as items 61-63) |
| 16 | 035088-01 | Cardboard Bezel with Graphics |
| 18 | 034536-01 | Foam Vibration Damper |
| 19 | 62-009 | Pushbutton Switch (for Kick Switches) |
| 20 | 60-06008 | Red Cylindrical Plunger |
| 21 | 62-039 | Pushbutton LED Switch (for 2/4 Player and Offside Switches) |
| 22 | 48-004 | 5-Inch 8-Ohm Speaker |
| 23 | 030868-01 | Connector Mount |
| 25 | 78-3116 | Gas Spring |
| 27 | 033127-01 | Black Molded Switch Bushing |
| 28 | 007882-02 | Interlock Switch Cover |
| 29 | 09992-01 | On/Off Switch Cover |
| 30 | 005594-01 | Monitor Tie-Down Brackets |
| 31 | 006870-01 | Coin Box Bracket |
| 32 | 60-06012 | Adapter Bezel for Kick Switches |
| 33 | 000869-01 | Speaker Grille |
| 34 | 034537-01 | Mesh Ventilation Grille |
| 35 | 75-07068 | Nylon Washer with .503” Inside Diameter x .756” Outside Diameter x .177” |
Thick
| 50 | 73-3029 | Special Retaining Clip for Gas Spring |
| 53 | TM-144 | Technical Manual for Soccer Game |
| 55 | 035118-01 | Danger Label (for Interlock and On/Off Switch Covers) |
| 57 | 75-99518 | #8-32 Nut/Washer Assembly |
| 58 | 71-103203 | 25°125°1$1.00 Coin Door Assembly |
| 59 | 92-040 | 23-Inch Wells-Gardner Black-&-White Monitor |
| 60 | TM-125 | Technical Manual for Wells-Gardner Monitor |
| 61 | A021084-02 | Voltage Selection Plug (120V) |
| 62 | A021084-04 | Voltage Selection Plug (220V) |
| 63 | A021084-05 | Voltage Selection Plug (240V) |
| 69 | DP-144-01 | Schematic Drawings for Soccer (Sheet 1) |
| 70 | DP-144-02 | Schematic Drawings for Soccer (Sheet 2) |
‘emission trom the corporat}
| 4
\ ° Wy oSP Jot I \ | é
Lon
Figure 16 Hinges, Latches and Monitor Shield A034103-XX A Parts List
| Item | Part No. | Description |
| 4 | 035104-01 | Tempered-Glass Monitor Shield with Graphics |
| 15, | 034383-01 | Hinge |
| 16 | 034388-01 | Latch Keeper Bracket |
| 7 | 78-3408 | Spring Draw Latch (Hook End) |
ET
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING re nt n ne
Beerse “|
Pos couoR « Y 5 Se 2 bk
cs @ \@ eca0) en 8 Ria @ BRia
BACK VIEW
Figure 17 Control Panel Assembly A035105-01 A Parts List
| Item | Part No. | Description |
| 1 | 035009-01 | Control Panel with Graphics |
| 2 | A033360-01 | Trak Ball Assembly |
| 3 | A035195-01 | Control Harness Assembly |
Figure 18 Trak Ball™ Assembly A033360-01 G
Item Part No.
033355-01 033356-01 033357-01 033358-01 033359-01 033361-01 033362-01 033363-01 033364-01 033365-01 000616-01 033366-01 74-A00011 A009060-02 73-3006 72-8808 72-1006S
72-1606S
72-1408S
72-8920S 85-1808B 75-3608S,
75-046S, 75-0488, 75-040S 75-041S 75-010S 75-018S 75-016S 75-990504C 75-916S 75-919S 034168-01 Qty.
BP R YVONNAANAAaNyHMHAAAA
B2ORONNANON WHR Figure 18 Trak Ball” Assembly Parts List
Description
Base Plate Top Plate Cover Plate (Acrylic) Corner Post End Post Steering PCB Bracket Roller Shaft Cylindrical Post Adjustable Post Spacer Light Hub Trak Ball Phenolic Spacer, 1/8” inside diameter x ¥%” outside diameter x %” long Steering Printed Circuit Board Assembly — see Figure 19 Carbon Spring Steel External Retaining Ring, for 3/8" shaft diameter #8-32 x V2" Hex Socket-Head Cap Alloy Steel Machine Screw #10-32 x 3/8" Cross-Recessed Pan-Head Cadmium-Plated Steel Machine Screw #6-32 x 3/8” Cross-Recessed Pan-Head Cadmium-Plated Steel Machine Screw #4-40 x 2" Cross-Recessed Pan-Head Cadmium-Plated Stee! Machine Screw #3/8-16 x 1%” Hex Socket-Head Cap Alloy Steel Machine Screw #8-32 x 2" Socket Cap Flat Countersunk-Head Black-Oxide Steel Screw #6-32 x V2" Cross-Recessed Flat-Head Cadmium-Plated Steel Machine Screw #6 Zinc-Plated Steel Split Lock Washer #8 Zinc-Plated Steel Split Lock Washer #10 Steel Split Lock Washer #3/8 Steel Split Lock Washer #10 Flat Plain SAE-Standard Zinc-Plated Steel Washer #8 Flat SAE-Standard Zinc-Plated Steel Washer #6 Flat Plain SAE-Standard Zinc-Plated Steel Washer #4-40 Shallow-Pattern Prevailing-Torque Corrosion Resistant Lock Nut #6-32 Standard Cadmium-Plated Steel Machine Hex Nut #3/8-16 Standard Cadmium-Plated Steel Machine Hex Nut Label with Lubrication Instructions
°
RG eEWING BD
yoosceo 2NBC4R NOTICE 10 ALL PERSON ev IHATA® CONSENTIAL TRebrooucts THIS ORAWING
ony thereat except for manutat Dorated and tor manulactos Traces shown are on opposite side.
Figure 19 Steering Board Assembly A009060-02 c Parts List
| Item | Part No. | Description (Ret. Designations & Locations in Bold) |
| 5 | 10-5392 | 3.9K Ohm, +5%, V¥sW Resistor (R14, 15) |
| 6 | 10-5331 | 330 Ohm, +5%, YW Resistor (R10-13) |
| 7 | 10-5471 | 470 Ohm, +5%, YW Resistor (R7- 8) |
| 8 | 27-250104 | 0.1 uf, + 20%, 25V Ceramic-Disk Radial-Lead Capacitor (C2) |
| 9 | 29-046 | 10 uf, + 10%, 20V Tantalum Axial-Lead Capacitor (C1) |
| 10 | 34-2N3643 | Type 2N3643 Switching Transistor (Q1, 2) |
| 13 | 79-58005 | 10-Contact Connector |
| 14 | 030369-01 | Radial Optical Coupler |
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Q ao) © 3 3 Sw a q = = (3)
a [He ee
TOP VIEW
4REQ’D ®
BOTTOM VIEW
Figure 20 Power Supply Assembly for Raster-Scan Games A034560-01 B
Figure 20 Power Supply Assembly for Raster-Scan Games Parts List Ss
| Item | Part No. | Qty. | Description |
| A | A034955-01 | 1 | Power Supply Sub-Assembly, Rev. A, consisting of the following 17 items: |
| 1 | 034482-01 | 1 | Base for Power Supply Chassis |
| 2 | 79-4411006 | 1 | Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post |
| 3 | 79-3206 | 1 | 5-Position 3AG Fuse Block with %” Quick-Disconnect Terminals |
| 4 | 46-2017002 | 3 | 7-Amp. 250V 3AG Slow-Blow Glass Cartridge-Type Fuse |
| 5 | 46-2013002 | 3 | 3-Amp. 250V 3AG Slow-Blow Glass Cartridge-Type Fuse |
| 6 | 29-053 | 1 | 26,000 uf 15V Electrolytic Capacitor |
| 7 | 78-70501SG | 1 | 2" Diameter Capacitor Mounting Bracket |
| 8 | 79-15021001 | 1 | 2-Circuit Single-Row Terminal Block |
| 9 | 78-2708 | 1 | Nylon Type 6/6 Hole Bushing with 5/8” Inside Diameter x 55/64” |
Outside Diameter x 4" Thick
| 10 | A006555-01 | 1 | Rectifier Printed Circuit Board Assembly |
| ant | 72-HA4804S, | 3 | #8-32 x 4” Cross-Recessed Pan-Head Zinc-Plated Steel Thread-Rolling |
Tri-Fluted ‘Taptite” Screw
| 12 | 72-HA4812S | 1 | #8-32 x %4" Cross-Recessed Pan-Head Zinc-Plated Steel Thread-Rolling |
Tri-Fluted “Taptite” Screw
| 13 | 72-1008F | 2 | #10-32 x V2" Cross-Recessed Pan-Head Zinc-Plated Steel Thread-Rolling |
Tri-Fluted “Taptite” Screw
| 14 | 72-HA4606S | 4 | #6-32 x 3/8" Cross-Recessed Pan-Head Zinc-Plated Steel Thread-Rolling |
Tri-Fluted “Taptite” Screw
| 15 | 75-010S | 2 | #10 Flat Plain SAE-Standard Zinc-Plated Steel Washer |
| 16 | 75-0188 | 4 | #8 Flat Plain SAE-Standard Zinc-Plated Steel Washer |
| 17 | 75-99518 | 1 | #8-32 Nut/Washer Assembly |
| B | A034630-01 | 1 | RFI Filter Assembly |
| Cc | A034629-01 | 2 | A.C. Harness Assembly |
| D | A034623-01 | 1 | Power Supply Harness Assembly (tor Raster-Scan Games) |
| E | 034544-01 | 1 | Fuse Block Cover |
| F | 75-018S | 4 | #8 Flat Plain SAE-Standard Zinc-Plated Steel Washer |
| G | 75-99518 | 4 | #8-32 Nut/Washer Assembly |
| H | 72-HA4812S | 2 | #8-32 x 3/4” Cross-Recessed Pan-Head Zinc-Plated Steel Thread-Rolling |
Tri-Fiuted ‘“‘Taptite” Screw
a
42% wO=se NO
>
z
o
Figure 21 Regulator/Audio PCB Assembly A034485-01 D
Figure 21 Regulator/Audio PCB Assembly Parts List xs
| Item | Part No. | Qty. | Description (Ref. Designations in Bold) |
| 2 | 10-51P0 | 2 | 1 Ohm, + 5%, %W Resistor (R10, 19) |
| 3 | 10-5100 | 2 | 10 Ohm, + 5%, %4W Resistor (R11, 20) |
| 4 | 10-5330 | 1 | 33 Ohm, + 5%, %4W Resistor (R3) |
| 5 | 10-5101 | 5 | 100 Ohm, + 5%, YW Resistor (R4, 12, 17, 18, 22) |
| 6 | 10-5271 | 1 | 270 Ohm, + 5%, “4W Resistor (R1) |
| 7 | 10-5102 | 1 | 1K Ohm, + 5%, %4W Resistor (R2) |
| 8 | 10-5272 | 1 | 2.7K Ohm, + 5%, YW Resistor (R23) |
| 9 | 10-5752 | 1 | 7.5K Ohm, + 5%, YsW Resistor (R7) |
| 10 | 10-5103 | 2 | 10K Ohm, + 5%, %W Resistor (R13, 14) |
| W | 10-5392 | 1 | 3.9K Ohm, + 5%, YW Resistor (Ré6) |
| 13 | 11-5221 | 2 | 220 Ohm, + 5%, v2W Resistor (R9, 21) |
| 15 | 12-52P7 | 1 | 2.7 Ohm, + 5%, 1W Resistor (R5) |
| 16 | 19-100P1015 | 1 | .1 Ohm, + 3%, 7W Wirewound Resistor (R24) |
| 17 | 19-315102 | 1 | 1K Ohm Vertical PCB-Mounting Cermet Trimpot, Bournes Series |
3352V-1-1K — (R8)
| 20 | 24-250106 | 2 | 10 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C6, 15) |
| 22 | 24-250477 | 3 | 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C1, 4, |
12)
| 23 | 24-250108 | 3 | 100 pf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C9, 10, |
13)
| 25 | 27-250103 | 2 | .01 pf Ceramic-Disc 25V Radial-Lead Capacitor (C5, | (14) |
| 26 | 27-250104 | 2 | -1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C3, C11) | |
| 27 | 27-250224 | 2 | .22 uf Ceramic-Disc 25V Radial-Lead Capacitor (C8, 17) | |
| 29 | 27-250102 | 3 | .001 uf Ceramic-Disc 25V Radial-Lead Capacitor (C2,7, | 16) |
| 31 | 31-A14F | 2 | 50V 2.5A Miniature Axial-Lead High-Current Rectifier | (CR1, CR4) |
| 32 | 31-1N4001 | 2 | 50V Silicon Rectifier 1N4001 Diode (CR2-3) | |
| 34 | 33-TIP32 | 1 | PNP Power Transistor, Type TIP32 (Q2) | |
| 35 | 34-2N3055 | 1 | NPN Silicon Transistor, Type 2N3055 Q3) | |
| 36 | 34-2N3904 | 2 | NPN Silicon Transistor, Type 2N3904 (Q4, 6) | |
| 38 | 37-LM305 | 1 | 5V Linear Voltage Regulator (Q1) | |
| 39 | 37-TDA2002A | 2 | Type TDA2002A 8W Linear Audio Amplifier Integrated Circuit (Q5, 7) | |
| 44 | 79-58008 | 1 | 9-Position Connector Receptacle (J7) | |
| 45 | 79-58092 | 1 | 6-Position Connector Receptacle (J6) | |
| 46 | 79-58059 | 1 | 4-Position Connector Receptacle (J8) | |
| 47 | 79-20230 | 19 | Female PCB-Mounting Terminal | |
| 48 | 034531-01 | 1 | Heat Sink | |
| 49 | 72-1608C | 4 | #6-32 x 2" Cross-Recessed Pan-Head Corrosion-Resistant Steel |
Machine Screw
| 50 | 75-99516 | 7 | #6-32 Nut/Washer Assembly |
| 51 | 75-056 | 7 | #6 Internal-Tooth Steel Lock Washer |
| 52 | 020670-01 | 6 | Test Point |
| 53 | 75-F60805 | 3 | #6-32 x 2" Binder-Head Nylon Screw |
| 57 | 78-16008 | 1 | Thermally Conductive Compound for the 2N3055 |
| 58 | 78-16014 | 3 | Thermally Conductive Compound for TDA2002A and TIP32 |
| 60 | 52-003 | 2 | Teflon-Insulated Solder-Plated Solid Copper PCB-Mounting Jumper |
Wire with .6” Centers
| 61 | 52-004 | 2 | Teflon-Insulated Solder-Plated Solid Copper PCB-Mounting Jumper |
Wire with .3” Centers
EF io8
<2) VERSION.
2 se Oe ar (03
iii
FARSIDE,
Figure 22 Soccer Game PCB Assembly A034905-01 and -02 A
Part No.
100000-221 100000-331 100000-471 100000-102
100000-152 100000-222 100000-392 100000-103 100000-223 100000-473 100000-563 100000-104 100000-224 100000-334 100000-394 21-101103 21-101223 24-250106 24-250107 24-250478 27-250102 27-250103 27-250104
28-101101 31-1N914 31-A14F 34-2N3643 34-2N6044 37-74LS00 37-7402 37-74LS02 37-7404 37-74LS04 37-74H04 37-7408 37-74LS08 37-74LS10 37-74LS14 37-74LS20 37-74LS27 37-74LS32 37-7442 37-74LS42 37-7474 37-74LS74 37-74LS83 37-74LS86 37-7496 37-74LS151 37-74LS153 37-74LS157 37-74LS163A 37-74LS 164 37-74LS166 37-74LS174 37-74LS175 37-74LS191 Figure 22 Soccer Game PCB Assembly Parts List
Description (Ref. Designations and Locations in Bold)
220 Ohm, +5%, %4W Resistor (R29, 42) 330 Ohm, +5%, %W Resistor (R20, 21, 26) 470 Ohm, +5%, %W Resistor (R17, 19, 22). 1K Ohm, +5%, %W Resistor (R1, 2, 7, 8, 10, 15, 16, 18, 27, 28, 43, 44, 74, 75, 81, 82) 1.5K Ohm, +5%, %4W Resistor (R25) 2.2K Ohm, +5%, ¥aW Resistor (R24, 45-47) 3.9K Ohm, +5%, “4W Resistor (R23) 10K Ohm, +5%, “%4W Resistor (R9, 30-41, 49-73) 22K Ohm, +5%, %4W Resistor (R48) 47K Ohm, +5%, %W Resistor (R76, 77, 79) 56K Ohm, +5%, %W Resistor (R13) 100K Ohm, +5%, “%W Resistor (R12) 220K Ohm, +5%, %4W Resistor (R14, 80) 330K Ohm, +5%, %W Resistor (R78) 390K Ohm, +5%, %4W Resistor (R11) .01 pf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C92) .022 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C93) 10 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C46) 100 yf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C60) 4700 yf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C76) .001 yf Ceramic-Disc 25V Radial-Lead Capacitor (C88) .01 yf Ceramic-Disc 25V Radial-Lead Capacitor (C54-59, 77-86, 89-91) -1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C1-33, 35-45, 47-53, 61-64, 67-75, 87, 94-98) 100 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C34) 75V 1N914 Switching Diode (CR1) 2.5 Amp. Miniature Axial-Lead High-Current Rectifier (CR2, 3) Type 2N3643 NPN Switching Transistor (Q1, 2) Type 2N6044 NPN Darlington Transistor (Q3-5) Type 74LS00 Integrated Circuit (B10) Type 7402 Integrated Circuit (P10) Type 74LS02 Integrated Circuit (£9) Type 7404 Integrated Circuit (C10) Type 74LS04 Integrated Circuit (K10) Type 74H04 Integrated Circuit (B9) Type 7408 Integrated Circuit (C6, L8, A10) Type 74LS08 Integrated Circuit (D2, D3) Type 74LS10 Integrated Circuit (K8) Type 74LS14 Integrated Circuit (B4, E11, £12, R13) Type 74LS20 Integrated Circuit (L7) Type 74LS27 Integrated Circuit (F10) Type 74LS32 Integrated Circuit (A5, B5, H10) Type 7442 Integrated Circuit (C5) Type 74LS42 Integrated Circuit (A6, D10) Type 7474 Integrated Circuit (A8, L10, M10) Type 74LS74 Integrated Circuit (E10, J10, A11, F11, R11, D12, F12, R12) Type 74LS83 Integrated Circuit (C4, L5, M5) Type 74LS86 Integrated Circuit (R3, R5, A7) Type 7496 Integrated Circuit (A4) Type 74LS151 Integrated Circuit (D8) Type 74LS153 Integrated Circuit (4, F4, H4, J4, K4, E6, F/H6, HiJ6, K6, E8, L9) Type 74LS157 Integrated Circuit (B1, C1, D1, R1, P5, M8, N8, P9, R9) Type 74LS163A Integrated Circuit (J9, K9) Type 74LS164 Integrated Circuit (B7, C7, D9) Type 74LS166 Integrated Circuit (M9, N9) Type 74LS174 Integrated Circuit (F8, H8) Type 74LS175 Integrated Circuit (P4) Type 74LS191 Integrated Circuit (H11, J11, N11, P11, H12, 12, N12, P12)
Figure 22 Soccer Game PCB Assembly, continued Parts List
| Item | Part No. | Description (Ref. Designations and Locations in Bold) |
| 78 | 37-74195, | Type 74195 Integrated Circuit (P1) |
| 79 | 37-74LS273 | Type 74LS273 Integrated Circuit (D6, D7) |
| 80 | 37-74LS374 | Type 74LS374 Integrated Circuit (P2, D4, N5, L6, M6, J8) |
| 81 | 37-9316 | Type 9316 Integrated Circuit (L4, M4, B8, C8, C9) |
| 82 | 37-9321 | Type 9321 Integrated Circuit (D5) |
| 83 | 37-8T28 | Type 8T28 Integrated Circuit (L3, M3) |
| 84 | 37-8097 | Type DM8097N Integrated Circuit (D11, K11, M11, K12, L12, M12) |
| 85 | 37-555 | Type 555 Integrated Circuit (C12) |
| 86 | 37-LM324 | Type LM324 Integrated Circuit (B12) |
| 90 | 41-3003 | 100 zH, +5%, Hot-Molded Plastic Fixed R.F. Choke (L1-6, 9-14) |
| 94 | 62-001 | SPST Pushbutton Switch (A12) |
| 95 | 66-114P1T | 4-Station Single-Throw, Dual-Inline-Package Bit Switch (L11) |
| 96 | 66-118P1T | 8-Station Single-Throw, Dual-Inline-Package Bit Switch (C11) |
| 99 | 035326-01 | Heat Sink (F9, H9) |
| 100 | 78-13016 | Tra-Bond Cement for Heat Sink |
| 103 | 79-42C40 | 40-Contact Medium-Insertion-Force IC Socket (C2/3) |
| 106 | 81-4302 | Nylon Snap-In Fastener (for Item 45) |
| 109 | 020670-01 | Test Point |
| 112 | 90-102 | 12.096 MHz, + .005%, Crystal (V1) |
| 115 | 90-6010 | Microprocessor (C2/3) |
| 116 | 90-7022 | Random-Access Memory (F9, H9) |
| 117 | 90-7031 | Random-Access Memory (E5, F/H5, H/J5, K5, E7, FIH7, H/J7, K7) |
| 118 | 90-7033 | Random-Access Memory (N3, P3) |
| 122 | 034006-01 | Programmable Read-Only Memory—Sync_ (N4) |
| 123 | 035250-01 | Programmable Read-Only Memory—Alphanumerics (R2) |
For remaining memory components and their part numbers, see next page.
Figure 22 Soccer Game PCB Assembly, continued Parts List
Memory Components and Their Equivalents (Locations Shown in Bold)
-01 P.C. Boards Alternate -01 P.C. Boards -02 P.C. Boards (PROMs) (PROMs) (ROMs)
035222-01 £1
035223-01 F1
035224-01 E2
035225-01 F2 035251-01 £1
035238-01 E3
035252-01 E2
035226-01 H1 035253-01 H1 035227-01 J1 035239-01 F3 035228-01 H2 035254-01 H2 035229-01 J2
035230-01 K1
035231-01 L1
035232-01 K2
036233-01 L2 035255-01 K1
035240-01 J3
035256-01 K2
035234-01 M1
035235-01 N1
035236-01 M2
035237-01 N2
035242-01 R7 035257-01 M1
035241-01 K3
035258-01 M2
035259-01 R7 035244-01 P7 035246-01 R6 035243-01 R8 035260-01 R8& 035245-01_ P8&
035247-01 N7
035249-01 N6
035248-01 M7
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproguetion, forbidden ‘witnaut ihe iWeh_permission of Atari
{en license, no right to reprodues this drawing Is granted or the subject matter thereot uniess by watten agreement lwun oF written permission trom ine corporation
Figure 23 Main Harness and Component Assembly A035194-01 A Parts List
| Item | Part No. | Description |
| 1 | A035193-01 | Main Harness |
| 2 | A030169-02 | Volume Control Bracket Assembly |
| 3 | 68-002 | Interlock Switch (2 per game) |
| 4 | 000268-02 | Interlock Switch Mounting Bracket |
| 5 | A034631-01 | On/Off Switch Assembly |
~— ee Atari Soccer TM-144 1st printing
YOUR COMMENTS, PLEASE!
Your comments will assist Atari in improving the usefulne 3 of our publications. They are an important part of preparing for revisions of maiiuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A.
If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.
Page: Comments:
Fill in if you wish a reply:
Name Firm C Distributor OO Operator
Address Cl Other City State Zip
First fold
BUSINESS REPLY MAIL
FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA
POSTAGE WILL BE PAID BY ADDRESSEE
Atari, Inc. Attn.: Field Service/Coin-Op Division P. O. Box 427 Sunnyvale, California 94086 No Postage Necessary if mailed in the United States
Second fold
aBpa siyy adey
Cut along this line
pen FES BEES BEN BE RK Ren Been. 2
> =
> > id
WARRANTY
Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty
- days from date of shipment. None of the Seller's other products or parts thereof are warranted.
If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
- Such products are returned prepaid to Sellers’ plant; and
- Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.
In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.
Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller’s part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order. =
= = © ©
0 SEE SE ES SS IS The use of any non-Atari parts may void your warranty, according to the terms of the waranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety.
Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is perfomed by such distributor.
This document is and contains confidential trade secret information of Atari, Inc.
This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.
Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc.
ATARI INC 1265 BORREGAS AVENUE P.O. BOX 427 @ SUNNYVALE, CALIFORNIA 94086 r ) ATARI 408/745-2000 « TELEX 35-7488