Wizard of Wor (General Instructions Domestic) (M051-00961-A022)
Wizard of Wor (Dave Nutting Associates / Midway, 1980) · Document · 7 pages · original scan
GENERAL INSTRUCTIONS
FOR
WIZARD OF WOR (DOMESTIC)
INSTALLATION
- Unlock and open the coin box door.
- Remove four "CABINET LEVELING LEGS" from inside the coin box,
- Tip the cabinet to the side and remove the shipping cleats from its bottom.
A. Locate the threaded holes - one in each corner ~ and install the CABINET LEVELING LEGS in them.
B. Level the cabinet.
C. When finished, cabinet should be stable in the up-right position.
4, Plug the game into 110 volt, 60 cycle A.C. wall outlet only.
wae ---) MARNING- Game MUST be properly grounded.
A. The power ON/OFF switch is located on top of the cabinet toward the back.
LINE VOLTAGE SAFETY INTERLOCK SWITCHES
Line voltage Safety Interlock Switches have been provided for your protection. The locations of these Safety Interlock Switches are: a) inside the rear of the cabinet on the right side (as you face back of cabinet) and b) inside the cabinet on the left side (as you look into the front access door).
When the cabinets access doors are secured in place, the Safety Interlock Switch plungers are in a fully depressed condition. The game circuit can function normally.
When either one - or both - of the cabinets access doors are removed, the Safety Interlock Switch plunger(s) are in a partially extended position. This isolates the game circuit from the line voltage.
To restore power to the game circuit for servicing with the access doors removed, gently pull the Safety Interlock Switch plunger(s) out to a fully extended position. PART NO. _4051-00961-A022
SELF-TEST
A slide switch is provided to make the game run a "Self-Test" on itself.
When the Self-Test Switch is in the "ON" position the monitor screen will display the results of certain test functions it has run on itself. (These will be discussed in more detail later.)
The Self-Test Switch is located on the mounting frame for the left hand coin meter on the back side of the coin box door.
TO SERVICE THE CONTROL PANEL AND TO REMOVE THE DISPLAY GLASS.
1.
2.
6. Unlock and open the coin box door.
Reach inside and upward to the back side of the Control Panel.
Release the two clamps, one mounted on the left cabinet wall and one on the right cabinet wall.
Disconnect the Control Panel wire harness jacks and ground wire "Wire- Nut" located just inside the coin box door.
Lift Control Panel up and away from cabinet being careful not to catch the wiring on anything.
With the control panel removed, the Display Glass can be lifted out.
VOLUME CONTROL POTS
1. The volume for all game sounds is controlled by the Audio Amplifier P. C. Board.
This Board is mounted in a bracket which is secured to the back edge of the coin box.
The Volume Control Pots can be reached through the coin box door.
See the label on the Volume Control mounting fixture for the individual control functions.
A. Turning each Control to the right will make those sounds louder.
B. Turning each Control to the left will make those sounds softer.
VOLTAGE CONTROL POTS
i. The Voltage Control Pots are located on the Power Supply P.C. Board (A082-90006-B000) .
These Pots are preset at the factory and should NOT be tampered with at all unless the distributors service department is contacted first.
-~3-
POWER SUPPLY
“SELF-TEST” SCREEN DISPLAY
MOVE DIR YES or NO RI-UP-LF-DN " FIRE i PL 1 " COIN 1 u SLAM
YES or NO SWL 7 sw2 " sw3 " swa P.c.B.
POT LOCATION
SCREEN RAM OK STATIC RAM OK ROM OK
YES
cOIN 3
YES MOVE DIR or NO "
"
"
sSW5
swW7 sws RI-UP-L¥-DN FIRE PL 2 COIN 2
EXPLANATION OF SCREEN DISPLAY IN SELF-TEST MODE
When ali switches and/or controls are moved - with the exception of SWl thru SW8 - a tone is emitted from the games speaker system until the switch and/or control is allowed to return to its normal condition.
Putting the game into the Self-Test Mode is the easiest and best way to check for proper operation of all the games switches, controls, and major electronic components.
The letters "R" "A" "M' (pronounced "RAM" like the male animal) stand for Random Access Memory.
The letters "R" "0" "M" (pronounced like the first three letters in the word "ROMP") stand for Read Only Memory.
SCREEN RAM OK /Means that the RAM Chip that controls the screen functions is working preperly. If it were not working properly - the screen will flash alternating different colors.
STATIC RAM OK ‘Means this RAM Chip is working properly. If it were not working properly - the word "OK" would be replaced with the word "BAD".
ROM OK /Means that all the ROMs are working properly. There are seven ROMs and sometimes eight.
The eighth ROM is an "EPROM" (pronounced with a long "E" as in the word "EASY" and "PROM" as in the high school dance). These letters stand for Erasable Programable Read Only Memory.
The ROMs are called out by their identification letter: A, B, @, D, E, F, G, and sometimes X.
"X" is the EPROM. It is switch selectable and is only used in games that have to work with a language other than English.
If any of the ROMs are not working properly - their letter(s) will be listed out beside the word ROM instead of the word "0K".
MOVE DIR /This is a two part check of the WORRIOR control stick switches. There are four switches under each control stick; one each for "left", "right", "up", and "down".
- The first part (when switch blades 3 & 1 touch) is the direction of the player - a "DIR" command. This will be displayed as either left-"LF", right-"RT", up~"UP", or down-"DN" according to the position of the control stick.
- The second part (when switch blades 3, 1, & 2 all touch) checks the mobility of the player - a "MOVE" command. This will be displayed as either a "YES" (that there is movement) - or a "NO" (that there is not).
- After these checks have been performed and the control stick allowed to return to its stationary position, the "MOVE" and "DIR" commands should both register "NO" "NO" to indicate there is not any switch contact.
PL I /No indication until ONE PLAYER START BUTTON is pushed — if this switch is working properly - "YES" will be displayed next to "PL 1". "NO" will then appear when switch is allowed to return to its normal position.
PL 2, COIN 1, COIN 2, and SLAM /All work the same way as described for "PL 1" above.
COIN 3 /No indication at all when there is only a "2 Coin Acceptor" door on the game. When there is a "3 Coin Acceptor" door on the game, it functions the same way as the other two coin switch tests (COIN 1 and COIN 2).
SW1 thru SW8 /These are the Option Selection Switches. A "YES" indication means that particular switch is in the "ON" condition. A "NO" indication means that particular switch is in the "OFF" condition.
- SA -
WORRIOR CONTROL STICK ADJUSTMENTS
TRAVEL OF PT. NO. 091-00700-0000 ACTUATOR IS APPROX. 1/8. SWITCH BLADE ASS'Y SHOULD BE ADJUSTED TO MAKE CONTACT WITH BLADE #1 AT 1/16 OF TRAVEL AND BLADE #2 AT 3/32 OF TRAVEL. 092I1- 00700-0000
BLADE “1
BLADE "2
0017 — OOI0I-0529
0020-00202-0000
A963 -00013 -0000
BOTTOM VIEW
~ 6+
WIZARD OF WOR
OPTION SWITCH SETTINGS
Option switches are located on the game P.C.B. in the commercial card rack.
COINS PER CREDIT
LEFT HAND COIN SLOT IS CONTROLED BY Sw#1
sw#l
OFF ON 1 COIN 1 CREDIT 2 COINS 1 CREDIT
RIGHT HAND COIN SLOT 1S CONTROLED BY SW#2 AND Sw#3 Sw 3 swe 2
| OFF | OFF | 1 COIN | 1 CREDIT |
| OFF | ON | 2 COINS | 1 CREDIT |
| ON | OFF | 1 COIN | 3 CREDITS |
| ON | ON | 1 COIN | 5 CREDITS |
LANGUAGE
sweh
OFF ENGLISH
ON FOREIGN LANGUAGE (REQUIRES AQ82-91374-A000)
WORRIORS PER CREDIT
Swe
OFF 1 CREDIT = 2 WORRIORS / 2 CREDITS = 5 WORRIORS
ON 1 CREDIT = 3 WORRIORS / 2 CREDITS = 7 WORRIORS
BONUS PLAYER AWARDED:
SWH6
OFF BONUS WORRIOR AFTER 3rd DUNGEON
ON BONUS WORRIOR AFTER 4th DUNGEON
PLAY MODE
Swe]
OFF COIN PLAY
ON FREE PLAY
GAME ATTRACTION SOUNDS
swe8
OFF CONTINUOUS SOUND DURING "ATTRACT MODE"
ON SOUND DURING ATTRACT MODE ONLY IF GAME CONTROLS ARE TOUCHED. (WHEN ANY BUTTON OR CONTROL 1S TOUCHED, GAME PROVIDES SOUND FOR ONE COMPLETE CYCLE OF THE "ATTRACT MODE". tT WILL THEN BE QUIET UNTIL TOUCHED AGAIN.