Legend Makai
The Legend of Makai (Jaleco USA Inc., 1988) · Document · 8 pages · 3 sections · original scan
INSTRUCTION MANUAL “Legend of Makai™” a horizontal conversion kit
The Legend of Makai™ is a trademark of Jaleco USA Inc. ©1988 Jaleco Ltd.
“33 The Legend of Makai % he Princess has been | kidnapped by the evil undead Wizard of the Makai Wastelands. The People have lost all hope because it is said that the Wizard cannot be killed. You must prove them wrong as you travel through the forests, hills, and caves of Makai seeking the letters of the Spell that will end the Wizard’s evil forever and free the Princess of Makai. ) Tae wil
The Legend of Makai™ is a one or two player horizontal video game. A list of components and instructions are provided with this kit for your ease of installation. Using your existing cabinet and monitor, your finished product should look and play like a new game. Jaleco, USA
JALECO © 8617 W. Howard Street Niles, Illinois 60648 (312) 647-7077 FAX (312) 647-7087 KIT CONTENTS Description Part # PCB, The Legend of Makai™ 1350-041 8-Way Rotary Joystick Red Pushbutton Assemblies Yellow Pushbutton Assemblies White Pushbutton Assemblies Wiring Harness PCB Cage (FCC required) The Legend of Makai™ Marquee _ 1350-047 Side Panel Graphics (Left & Right) 1350-048 Control Panel Overlay 1350-049 Underlay Card (CRT) 1350-050 Control Panel Instruction Card 1350-051 Instruction Manual 1350-053
SPECIFIC REQUIREMENTS
Monitor — Horizontal, Negative Composite Sync Input
Power Supply — +5 VDC @ 7 Amp +12 VDC @ 1 Amp
- Make sure power is OFF
- Monitor and coin acceptors are functional
- Make sure game is properly grounded ) )
- Never expose PC board to direct sunlight ) )
- Do not use tester to check PC board
INSTALLATION INSTRUCTIONS
Cabinet Remove all graphics from pre-existing game. Inspect cabinet for any gouges or chips. Fill in as required with wood putty. Wipe cabinet clean and repaint if necessary. Apply the side graphics, using a straight edge as a guide line. Apply the decals to each side of cabinet. Using the old marquee from the previous game, place it on top of the new one. Mark to proper size, making sure that the title “The Legend of Makai™” is not excluded. Proceed to cut the plexi. Before installing the marquee replace all burned-out bulbs. Control Panel Remove control panel and remove old buttons, joysticks, and wiring. Strip off the old lexan overlay and any vinyl stickers. Prepare control panel surface by using sandpaper, making sure that the surface remains from the previous game are completely gone. Figure 1 is a suggested panel layout—use it if possible (if not, use your own discretion). Any remaining holes that are not being used, fill with wood blocks, putty, cardboard or epoxy. Apply the overlay to the control panel, making sure no air bubbles are present. Next, install the buttons stickers on the control panel in their proper locations. Replace joystick and buttons and return control panel to the game.
START @ @ Attack Jump Attack Jump @ OOP 0 0
Control Panel Layout
WIRING PROCEDURES
@ Disconnect the old wiring harness from the CPU board. Remove the board. Carefully
To wire the The Legend of Makai™ kit into the cabinet, the following steps are provided: @ Leaving several inches of wire from the old wiring harness at each connector, cut the wires near the game’s coin door, monitor, player panel, speaker and power supply. Do NOT cut the other side of these wires at the CPU board end.
@ An edge-connector schematic drawing is provided in this manual for your ease of rewiring. @ Using the new wiring harness, solder wires to the coin door, monitor, control panel, speaker and power supply, making sure all bare connections are sealed from exposure.
WIRING TO POWER SUPPLY
@ Locate the +5V leads color-coded RED and install them to the proper position on the power supply. @ Next, locate the +12V leads color-coded BLUE and install them to the proper position on the power supply as well. @ Last, position a BLACK ground wire from the harness and connect it. A continuous ground wire should be installed to every electronic component.
SETTING DIP SWITCHES
Before installing the PCB refer to the dip switch setting, and adjust the game to the specifications Sound may also be adjusted by turning the volume control either clockwise or counterclockwise.
INSTALLING THE FCC CAGE ASSEMBLY
Mount the FCC cage to the inside wall of the cabinet, making sure that there is no direct heat source and the spot is well ventilated, if not, damage to the board will result and void the warranty. Next mount the PCB making sure the edge-connector has enough room for connection. Plug the wiring harness onto the CPU board. Use plastic wire guides to support the harness. Position the FCC cage over the PCB and secure it with screws to the cabinet, making sure no wires are pinched. Before you apply power to the game, remove the main harness edge connector from the PCB.
Apply power to the game and measure the +5 volts at the edge connector and adjust to +5.15 VDC using a digital multi-meter. Measure the +12 VDC wires to be certain they are connected properly. Turn power off to game and re-connect the edge connector. Turn on power to the game and coin it up. Test all the controls and sound for proper operation.
SERVICE INFORMATION
To obtain replacement parts, please contact your distributor. For technical service contact Jaleco’s customer service department during the hours of 9 AM - 5 PM Central Time at (312) 647-7077. Thank you for your purchase of a Jaleco USA Inc. The Legend of Makai™.
Edge Connector Diagram (Edge Connector of Jamma Specs.)
Component Side Solder Side
GND GND GND GND
+5V +5V +5V +5V
+12V Key To Prevent Erroneous Insertion Coin Meter #1 +12V Key To Prevent Erroneous Insertion Coin Meter #2 Om NoOnORW Na xInmmMog WY
Speaker 1 (+) Speaker 1 (-)
Video Green Video Sync Service Switch Video Red Video Blue Video GND
Coin SW #2 2P Start 2P Up 2P Down 2P Left 2P Right 2P Push 1 2P Push 2 Coin SW #1 1P Start 1P Up 1P Down 1P Left 1P Right 1P Push 1 1P Push 2 ©) | VOLUME betaerry STEREOG) VOLUME MONO (SPEAKER 1) +>DANDTMONKXKS<CHMDVZS MAC
Speaker 2 (+) Headphone R (+) Speaker 2 (-)
The Legend of Makai™ bine
Be sure to turn off the power before resetting DIP switches. 3 | Dip Switch #4} 1Coin -1 Credit 1 Coin - 2 Credits ON Coin -3 Credits First Coin - 4 Credits Coinchute
OF
Coin - 1 Credit 1 Coin - 2 Credits 1 Coin -3 Credits Second 1 Coin - 4 Credits Coinchute [2 Coins - 1 Credit
4 Coins - 1 Credit
Attract Mode [Unecessary
Hero
PS Number of
Players
| NotUsed [ . Standard
Difficulty Difficult Level More Difficult
NotUsed [od Screen Normal Display Reverse (ge
OJ o}O/o}Olo}O PUTT TTT ET Bestest TTT
[e) al n mn m7 : fe) mui
olOlo|O BEBE a aT oO My —
nn O]O}o|O}O]}O}O PUTT tT LT eleieteisi SULT TTT Ir
: 5 5 5
[e) a a
[e) [e) a a aul nn [e) nm [e) a mn EEE nn nn it deeist ti dT dl tT eels 17 171 TNT nT
ie} Ke) Se TTT Te PET Teese TTT LT eieisisieielsis 17 Zz 17 nT 17 nT nT
fe) na nm
[e) a q TT Zz
Olo BRREEE
USER INFORMATION
WARNING
F.C.C. REGULATION COMPLIANCE
THIS KIT IS INTENDED FOR USE ONLY ON COIN- OPERATED VIDEO GAMES MANUFACTURED AFTER OCTOBER 1, 1983 WHICH HAVE BEEN VERIFIED FOR COMPLIANCE WITH REQUIREMENTS IN PART 15 OF F.C.C. RULES FOR A CLASS A COMPUTING DEVICE.
IMPROPER CONNECTION OF THIS KIT OR CONNECTION TO ANY OTHER GAME NOT SO MANUFACTURED OR VERIFIED FOR COMPLIANCE MAY CAUSE UNACCEPTABLE INTERFERENCE TO RADIO AND T.V. RECEPTION, REQUIRING THE OPERATOR TO TAKE WHATEVER STEPS ARE NECESSARY TO CORRECT THE INTERFERENCE.
THE P.C. BOARD CAGE SUPPLIED WITH THIS CONVERSION KIT MUST BE UTILIZED AND TERMINATED TO GROUND AT THE TIME OF INSTALLATION.
JALECO
5617 W. Howard St. Niles, IL 60648 TEL: (312) 647-7077 ~— FAX (312) 647-7087