CATHODE RAY TOMES

Atomic Punk 2

Dynablaster / Bomber Man (Irem (licensed from Hudson Soft), 1991) · Document · 17 pages · 41 sections · original scan

Page 1

CORPORATION

ATQMIC PUNK II

OWNERS MANUAL

Page 2

VIDEO GAME-OPERATOR:

Don’t Get Involved In A Federal Crime. Don’t Buy Or Operate Copy Or Unauthorized Boards In

Your Games.

Every operator who buys or Operates a counterfeit or unauthorized board (imported or domestic) is contributing to the end of our industry and committing a FEDERAL CRIME. New criminal laws have recently been enacted that provide for maximum penalties of $250,000 or five years in prison or both, per offense. EACH GAME IS A SEPARATE OFFENSE.

If you have any information about any unauthorized games in the United States, contact your local FBI or,

American Amusement Machine Association

205 The Strand

  • Puite Fe Alextfhdria, Virginia 22314 (703) 548-8044 All information wil be treated in confidence
Page 3

SAFETY

The following topics should be carefully studied to insure maximum reliability and safety for both serviceman and customer. Shock Hazard: The high voltage present on the monitor may be very dangerous. Extreme caution must be used when working with or around the monitors. Be certain that the grounding strap is attached to the monitor frame. The picture tube in the monitor is also a hazard and should be handled with care. Do not strike, scratch, or subject the tube to more than moderate pressure as it may implode causing serious injury from flying glass. Be certain that the control panel, power supply monitor, and coin door are all properly grounded to the ground wire inside the line cord. Do not remove ground prong off plug end.

PARTS LIST

  • & - Manual 1 - 3rd & 4th Player Cables 1 =,Marquee Art
  • PCB

ts IREM AMERICA CORPORATION® 8434 154th Avenue NE Redmond, WA 98052 (206) 881-0900 FAX (206) 881-6503

FOR SERVICE CONTACT:

Your authorized Irem America Corporation® Distributor or SUMMIT SERVICE 2274 University Avenue St. Paul, MN 55114 (612) 645-9077

WARRANTY REPAIRS

lrem America Corporation PCB have a 90 day warranty from date of shipment. This includes all failures except those caused by the installer such as miswiring.

All PCB must be returned by an authorized Irem America Corporation distributor. A Return Material Authorization must be obtained from Summit Service prior to returning material. A Purchase Order must also be given to Summit Service at this time. The package must be clearly marked with the RMA number.

Page 4

ATOMIC PUNK II® is protected by federal copyright laws and is the property of lrem America Corporation®. Any unauthorized versions of this game are illegal by federal law. AAMA protected stickers must be attached to the PCB. Please notify Irem America Corporation of any boards not having the AAMA seal.

IMPORTANT F.C.C. WARNING

THIS EQUIPMENT COMPLIES WITH THE REQUIREMENTS IN PART 15 OF FCC RULES FOR A CLASS A COMPUTING DEVICE. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA MAY CAUSE UNACCEPTABLE INTERFERENCE OF RADIO AND TV RECEPTION REQUIRING THE OPERATOR TO TAKE WHATEVER STEPS ARE NECESSARY TO CORRECT THE INTERFERENCE. YOUR FCC COMPLIANCE LABEL IS ENCLOSED IN YOUR KIT AND MUST BE ATTACHED TO YOUR GAME PRIOR TO PLACING ON LOCATION. THIS LABEL INDICATES YOUR GAME WAS DESIGNED TO MEET FCC STANDARDS 47CFR15.19. WE ADVISE USING STAPLES IF NECESSARY TO MAKE SURE THE LABEL STAYS ON.

DANGER

The isolation transformer must be used with the monitor’and power supply.

This game must be equipped with a three wire 110 volt ‘plug for safety. Under no circumstance remove the ground plug.

This game is designed with a JAMMA 56 pin connector. This plug is one of the finest operator friendly features in our industry today. What this means to you is that:

  • 1, 2,A, B, 27, 28, e and f are grounded
  • 3.4. C and D are +5 volts
  • 5 and E are -5 volts
  • 6 and F are +12 volts

Also, all video and joystick functions are always in the same place. Once a cabinet is wired for JAMMA, it is easily changed from game to game.

Many older games such as Pac Man®, etc., have the power supply on the board. This will not work!!! Only a JAMMA connector with proper voltage will work. Irem America Corporation® recommends using an 11 or 15 amp switching power supply with Atomic Punk II®.

MONITORS

Atomic Punk II® is designed to be operated with a horizontal raster scan monitor with negative sync (RGB). This means Atomic Punk II® will not work with any X-Y (Tempest, Space Dual, Star Trec), etc. An isolation transformer must be used in conjunction with the monitor. This is for your safety. The monitor also utilizes extremely high voltages. The monitor may also retain a charge for an extended period of time. Safety goggles must be worn while removing or replacing the monitor.

It is highly recommended that the monitor is verified good before the new Atomic Punk II® kit is installed in your new and or rebuilt cabinet.

Page 5

INSTALLATION OF KIT IN USED CABINET

To Disassemble:

1. Open back door and remove old board set and power supply, if you are using a new switching power supply.

  • Remove marquee glass and monitor glass.
  • Remove control panel and set aside.
  • Remove old wire harness, leaving 110 volt wiring intact. Also, leave the grounding straps to the monitor, coin door, control panel, and power supply intact.

Installation:

  • Mount the board set on the side panel of the cabinet as close to the middle of the game as possible (approximately 10-12” off bottom).
NOTE: Do not mount board directly below control or any vents or cracks so that liquids may seep on to the board. Do not forget about coins that may drop on to the board. Also, mount the board with edge connector facing up.
  • Mount the power supply on the bottom of the cabinet with connectors facing the rear of the cabinet. An optional mounting might be on the side panel just below the board set, connector to rear.
  • If the game does not have an isolation transformer, you must protect your customers and your game. Install one between the 110 volt line and your monitor/power supply.
  • Place the provided JAMMA wiring harness on the board. Connect the +5, +12, -5, and ground wires to the corresponding lugs on the power supply, connecting all the wires. If you don't, you will probably burn the board connector.
  • Runa wire from +12 volts to the coin door lights. Run a wire from +12 volts to the coin counters. This completes the power requirements.
  • Connect the Audio (+) and Audio (-) to the speaker.
  • Connect the video red, green, blue, ground, and sync to the corresponding wires on the monitor. If the monitor is not a negative composite sync, see sync modifications chart.
  • Cut the marquee to size. Replace the marquee lamp, if needed. Install the marquee panel.
  • Connect the coin 1 and coin 2 wires to the coin switches. Connect the coin counter 1 and coin counter 2 wires to the coin counters.
NOTE: If you only have one coin counter, see coin counter diagram. It will not matter if the coin counters are only rated at 6 volts, as the pulse is not long enough to burn out the counter.
Page 6
  • Disassemble the control panel of all the hardware. Do not remove the old panel overlay. Determine where to place the new joystick and buttons if they must be repositioned. Then, cut new holes.
NOTE: If you are going to use plexiglass over the control panel, we suggest that you use a good %" polycarbonate with a scratch resistant coating. We recommend GENERAL ELECTRIC LEXAN MRS5 with margard or TUFFAK CM-2. These do not crack or break with abuse.

Cut and drill plex as needed. Remove the old control panel overlay carefully and apply the new overlay on top of the old glue. Use an Exacto knife to cut out any button or bolt holes. Apply necessary decals over appropriate buttons. Now assemble the control panel.

  • Bolt the control panel to the cabinet. Now connect the appropriate wires to the correct switches. Connect the 1 player and 2 player start wires.
  • Be sure to install the FCC cage to avoid unnecessary radio frequency interference.
  • Power up the game. Look over your installation for errors, and then apply power, listening for unusual sounds. Check for smoke or sparks. If everything is okay, wire tie all wires to form a nice, neat wiring harness. Clean the cabinet inside and out. Measure the +5 volts on the furthest point from the edge connector and adjust 5 volts to 5.05 volts. Use a tinted plex over the monitor if there are burns in the screen. We suggest bronze or grey tinted plex. Touch up the cabinet with fresh paint, and then repair all cabinet dents or chips, using an auto body product called Duraglass. This is similar to bondo. You can consult your local auto body shop or auto parts supplier for this product, as well as advice on how to use it.
  • Be sure your ground plug is good. All metal exposed to the player must be grounded (coin door, control panel, etc.) including all metal inside exposed.

ATOMIC PUNK II®

Irem America Corporation recommends installing your new ATOMIC PUNK II kit in only a new or refurbished cabinet. Installing ATOMIC PUNK II in an older cabinet will result in lower earnings. The cabinet should be as follows:

  • horizontal monitor
  • 11 amp or larger power supply
  • monitor not laying down flat.
  • Use only 4 way joystick

2P 2-2P 4P ap

COINA—_COINBCOINA—_COINBCOINA—_COINB
SELECTOR SELECTORSELECTOR SELECTORSELECTOR SELECTORcons come soe como
COUNTER A COUNTERBCOUNTER A COUNTER BCOUNTER A COUNTER BCOUNTER A

COINA —_COINB

SELECTOR SELECTOR

COUNTER A COUNTER B SELECTORS P.C.B. CABINETS CHUTES SHARED SEPARATE

UPRIGHT TABLEg.f..fete]pee eee)iter peg.

The counters on the side of 3, 4P in no use.

Page 7

CABINETS

@ 2P UPRIGHT/TABLE @ COIN MODE 1 1 or 2 coin selectors (for the same kind of coins) Only 1 coin counter for Selector A.

@ COIN MODE 2 2 coin selectors (for different kind of coins) 2 coin counters (1 for each selector)

@ 4P SELECTORS SHARED @ COIN MODE 1 1 or 2 coin selectors (for the same kind of coins) Only 1 coin counter for Selector A

@ COIN MODE 2 2 coin selectors (for different kind of coins) 2 coin counters (1 for each selector)

@ 4P SELECTORS SEPARATE @ COIN MODE 1 4 coin selectors (1 for each player) Only 1 coin counter for all selectors

@ COIN MODE 2 Cannot be set.

@ 4P 2P + 2P Two 2 P cabinets are connected to each other. @ COIN MODE 1 Each table with 1 or 2 coin selectors (for the same kind of coins) Only 1 coin counter for selector A of 1, 2P side

@ COIN MODE 2 2 coin selectors (1 for each table) 2 coin selectors for each of selectors A and B for both tables.

Page 8

1.

SOLDER TO EXISTING CHIP

FIG.

FIG. Monitor Sync If your monitor does not have dual polarity positions for sync, you may use on of the following methods to get your game going.

CURE 1: Install a simple one |.C. Circuit on your logic board. This I.C. may be “piggy backed” on to another 7404 series chip for power by bending up all but the two power pins so that they are parallel to the top surface of the new I.C. and then connecting the power pins only to the existing chip. (See Fig. 1) Next connect the sync wires as shown in Fig. 2. (Note: Figure 2 shows a hookup for either composite or separate syncs.)

74Lso4

END +5VDC

HORIZONTAL_SYNC INPUT FROM P.C.B. COR COMPOSITE SYNC INPUT)

HORIZONTAL SYNC OUTPUT TO MONITOR COR COMPOSITE SYNC OUTPUT > VERTICAL SYNC INPUT FROM P.C.B.

VERTICAL SYNC OUTPUT TO MONITOR

NC.

NC.

GROUND

_BENT PINS.

EXISTING I.C.

CURE 2: Used for Wells-Gardner Video-Sync boards with positive sync connections only. (Vertical mount board 85x14 OB.)

Cut the traces on the solder side of the board between input pins 5 & 6 to the unbanded (anode) SOLDER

ends of diodes X201 & X202.

Add MPSA 56 transistor as follows: Collector to anode leads of diodes X201 & X202. Base pins 5 & 6 of the video input connector. Emitter to cathode (banded) lead of zener diode ZD201. Insert a 1N4148 diode - cathode to the emitter of the MPSA56 and anode to the base. (See Fig. 3)

RED

GREEN

BLUE 3

GND 4

VERT. 5S

HORZ. 1N4148 MPSASG

  • i

x202

x204 CUT BOTH TRACES zo2a1 74Lso4

FIG. +S¥DC

NC.

NC.

NC.

NC.

NC.

NC.

Page 9
  • Horizontal Tearing CAUSE: The negative sync signal of most logic sets are slightly different than the GO7-CBO monitor negative sync inputs. The result of this mismatch is a horizontal “wave” or “curl”.

CURE 1: On the monitor deflection board, replace C303 with a 10uf 25V radial lead capacitor with the positive lead towards the collector of X305. (CAUTION: be sure to check this step as the original cap is not polarized.) Then replace C501 with the cap removed from the C303 location.

CURE 2: Connect 1N4148 fast-switching diodes across both the positive and negative sync inputs to the monitor. (See Fig. 4) NOTE: Both diodes must be installed or you will not have vertical stability.

1N4148

NEGATIVE SYNC INPUT

  • HORZ. — VERT. GND

FIG. 4

1N4 148

POSITIVE SYNC INPUT

: 2 + HORZ. + VERT. GND BLUE GREEN

CURE 3: Join negative sync inputs J2 and J3 together with a jumper. Locate W102 and install a jumper from W102 to either J2 or J3.

CURE 4: For Wells-Gardner K4600 series monitors. Replace C356 (4 7uf 25V) on the Horizontal /vertical board (vertically mounted board nearest the flyback transformer) and center the horizontal hold pot. Turn L351 for the best horizontal stability and fine-tune with the horizontal width pot.

COIN COUNTER DIAGRAM

If only one coin counter is to be used install two diodes in the following manner:

+12 vde

1Na001 COIN COUNTER 1

COIN COUNTER COIN COUNTER 2

NOTE: IF DIODE INSIDE COIN COUNTER inaoo1 IS NOT PRESENT, INSTALL ONE.
Page 10

ATOMIC PUNK II© — HORIZONTAL SCREEN — 4 x 4 WAY JOYSTICK 2 BUTTONS DIP-1

FUNCTIONowen | 4234578
NUMBER OF PLAYERS3OFF | OFF
2ON_|OFF

4 OFF | ON

5ON_|_ON
DIFFICULTYNORMAL*OFF _| OFF
EASY*ON_|OFF

HARD OFF _| ON VERY HARD ON _| ON

CONTINUATION MODEYESOFF

NO ON

SOUND IN DEMONOOFF

YES ON

DIAGNOSTIC TESTNOOFF

YES ON DIP-2

FUNCTIONswitcH | 1| 2]3| 4]5|6| 7 | 8

se

FILP PICTURENOOFF

YES ON

CABINET TYPE~_2P UPRIGHT/TABLECAN | OFF

4P_ SELECTORS SHARED OFF | ON 4P_ SELECTORS SEPARATE ORF! OFF 4P 2P + 2P ON _| ON

1 COIN 1 PLAYoFF | oFF[OFF | OFF | OFF
2 COINS 1 PLAYoFF | ON[OFF | OFF | OFF

3 COINS 1 PLAY OFF | OFF | ON | OFF | OFF 4 COINS 1 PLAY orF | ON | ON | OFF | OFF

5 COINS 1 PLAYoFF | oFF[OFF | ON | OFF
6 COINS 1 PLAYoFF | ON[OFF | ON | OFF
MODE 11 COIN 2 PLAYSorF | OFF | ON | ON | OFF

1 COIN 3 PLAYS OFF | ON | ON | ON | OFF

1 COIN 4 PLAYSorF | OFF | OFF[OFF | ON
1 COIN 5 PLAYSoFrF | ON[oFF[OFF | ON

1 COIN 6 PLAYS OFF | OFF _| ON | OFF | ON 2 COINS 3 PLAYS OFF | ON | ON | OFF | ON 3 COINS 2 PLAYS ofr | OFF | OFF [ ON | ON

4 COINS 3 PLAYS|OFF | ON[OFF | ON | ON_

*CONTINUATION COIN OFF | OFF | ON | ON | ON

FREE PLAYLLOFF | ON | ON | ON | ON
COIN| _1COIN 1 PLAYON | OFF | OFF
MECH,2 COINS 1 PLAYON | ON | OFF_
(A)|3 COINST PLAY|ON | OFF | ON
MODE 25 COINS 1 PLAYON | ON | ON
|COIN|__1 COIN 2 PLAYON
jMECHON|
(8)1 COINS PLAYSONj
-1 COIN 6 PLAYSLL__[on[|{on| o

NB ‘

  • Please turn off the power switch before changing the DIP SW setting, or the change may not take effect
  • Select Coin Mode 1 in case a single coin selector or two selectors for coins of the same value are used.
  • Select Coin Mode 2 in case two coin selectors of coins of different values are used
  • CONTINUATION COIN is the mode which starts the game with 2 coins, but continues it with 1 coin alone. When this mode is set, no other coin modes can be set. For two players, 4 coins to start, 2 coins to continue in this mode.
  • DIP SWS is not used.

a

Page 11

FUNCTION COLOR

GROUND BLK +5 VOLTS

| GROUND BLK

+5 VOLTS

RED REO

-5 VOLTS BRN

+12 VOLTS

PREVENT KEY

(COIN COUNTER #1 pa : | GROUND BLU BLU/BAN BLACK AUDIO POS + WHT! BLK VIDEO RED RED VIDEO BLU BLU BLK

VIDEO GND TEST COIN INPUT 1 START 1 | 1 P DOWN YEL WHT/YEL, PNK/BLK ORG/BLU 1 P DOWN GRN/ORG 1 P LEFT GRN/BLU

1 P RIGHT 1P BOMB 1 P REMOTE CONTROL BOMB RED/YEL RED/WHT WHT/RED ATOMIC PUNK Il® JAMMA EDGE CONNECTOR/CABLE

| COMPONENT SIDE 8 BLK SOLDER SIDE COLOR FUNCTION oe a hh BLK | GROUND GROUND KD/DYNAMO — UNIVERSAL VIDEO WIRING 56 PIN EDGE CONN. PIN-OUT CHART (JAMMA COMPATIBLE)

COMPONENT SIDE SOLDER SIDE

~ 1 FUNCTION ] COLOR i i — COLOR FUNCTION

BLK GROUND

BLK GROUND

+5 VOLTS, #12 VOLTS

COIN COUNTER #2| GROUND AUDIO NEG - VIDEO GRN

GRN +5 VOLTS | RED +5 VOLTS

RED | +5 VOLTS

WHITE WHITE -5 VOLTS

| YELLOW YELLOW

| KEY L | KEY

COIN COUNTER #1, BRN COIN LOCK OUT 1 RED. QIN COUNTE!

WHT/BLK

L | | BLUE-OPTION OP.-BLU/BLACK

VIDEO RED RED.

WHT VIDEO SYNC* VIDEO BLU BLU

BRN/WHT SERVICE SWITCH VIDEO GND BLK GRN VIDEO GRN +12 oe

+} ____}__ GRAY VIDEO SYNC*

RED/ BLACK

vo] Y WHT/ORG z | WHT/BRN |S ‘ as _ TEST SW. | BROWN TILT SW.

GRN/YEL. COIN INPUT 2

RED/BLK “START 2 y 2P UP ORG/WHT 2P DOWN | ee ee ORG/GRN 2P LEFT 2 P RIGHT COIN SwW.1 WHITE COIN Sw. 2

START1 1 PUP 1 P DOWN GRAY VIOLET BLUE WHITE/GRAY START 2 SERVICE SWITCH | WHITE/VIOLET 2PUP WHITE/ BLUE 2P DOWN

1P LEFT GREEN WHITE/ GREEN 2P LEFT

1 P RIGHT YELLOW WHT/YELLOW 2 P RIGHT

BRN/BLK =| 2 P BOMB 1P PUSH 1 ORANGE

YEL/WHT 2P REMOTE | CONTROL BOMB

YEL/BLK

GROUND GROUND

  • Video sync composite negative. BRN/GRN 1 P PUSH 2 RED WHT/ORANGE 2PPUSH1 WHT/RED 2 P PUSH 2

BROWN 1PPUSH3 | WHT/ BROWN.

NC. BLUE/WHT GREEN/ WHT

NC. RED/WHT YELLOW/WHT NC.

GROUND. BLK BLK | GROUND

GROUND) BLK-OPTION BLK-OPTION | = GROUND

  • Video sync composite negative
Page 12

4-way joysticks, each with two buttons, and a horjzontally positioned monitor are required.

When the game is set 4P UPRIGHT A (No. 2 and No. 3 of DIP SW 2 OFF), only the coin mode 1 (No. 4 of DIP SW 2 OFF) can be used.

When the game is set 4P UPRIGHT B (No. 2 of DIP SW 2 OFF and No. 3 of DIP SW 2 ON), 2P UPRIGHT (No. 2 of DIP SW 2 ON and No. 3 of DIP SW 3 OFF) or 2P TABLE TYPE (No. 2 and No. 3 of DIP SW 2 ON), either coin mode 1 (No. 4 of DIP SW 2 OFF) or coin mode 2 (No. 4 of DIP SW 2 ON) can be used.

1-COIN CONTINUE is the mode which starts the game with 2 coins but continues it with 1 coin alone. When this mode is set, no other coin modes can be set. For two players, 4 coins to start, 2 coins to continue.

When the game is set 4P UPRIGHT A, each coin selector can be used independently.

When the game is set 4P UPRIGHT B, a coin selector can be used as a mutual.

cN3 cN4 en

1GROUNDvea1GROUND
23P RIGHTigsLeO™Lysate4P RIGHT

¢ ¥ os

33P LEFTmeowSe EOalg4P LEFT
» \2\
43P DOWN4KX4144P DOWN
53P UP—BR ARYSS4P UP
63P START64P START
73P COINcre Goes &we NV174P COIN

ines a ~

83P REMOTE‘DQeryPB4P REMOTE
CONTROL BOMBa.CONTROL BOMB
93P SETS BOMBSseh OXSas94P SETS BOMBS
Page 13

Diagnostic Test

  • Test Items The following tests are made: 1 RAM Test ROM Test 1/O PORT Test DIP Switch Test SOUND Test CHARACTER Test COLOR Test CROSS HATCH Test ONOnARwWN As soon as the number 8 of the DIP Switch 1 is turned to “ON” and the Power Switch is switched on,the Test 1 and 2 are started.

To finish the Tests, turn off the Power Switch and then the number 8 of the DIP Switch 1 to “OFF”.

Test Procedures

TURN “ON” 8 OF DIP SW 2 (2)

TURN ON POWER SWITCH

RAM and ROM Tests start

RETEST? PRESS 1P. No 2P BUTTONS

Yes No

PRESS BOTH 1P AND 2P BUTTONS | 4 _ PRESS 2P BUTTON MOVE 1P JOYSTICK UP AND DOWN TO SELECT TEST ITEM

PRESS THE ATTACK BUTTON TORGRTTEST DIP SWITCH ~ = * pie SwircH Teer | test SOUND TEST CHARACTER TEST COLOR TEST |

‘TEST, ENDS?, TURN OFF POWER SWITCH Yes 4

  • RAM and ROM TEST TURN 8 OF DIP SW 2 |__xnst) BACK TO “OFF”

Although the picture does not appear on the screen and only various patterns appear on itfora while after turning on the power switch, RAM’s for the picture are being tested during this time. If RAM's are found OK by the test, “RAM OK” and “ROM OK” will be displayed on the screen. If RAM(s) is (are) not good, “RAM NG O ” will appear on the screen.

The figure following the RAM NG” indicates the location of the defective RAM. WORK RAM (BYTE) 01 WORK RAM (WORD) PALLETE BUFFER BANK 0 (WORD) PALLETE BUFFER BANK 1 (WORD) PALLETE BUFFER BANK 2 (WORD) )

02V_RAM A (WORD)11
03.V_RAM B (WORD)12PALLETE BUFFER BANK 3 (WORD)
04V_RAM C (WORD)13OBJECT BUFFER BANK 0 (WORD)
05V_RAM D (WORD)14OBJECT BUFFER BANK 1 (WORD)
06RASTER SCROLL RAM A (WORD)15PALLETE RAM BANK 0 (WORD)

07 RASTER SCROLL RAM B (WORD) RASTER SCROLL RAM C (WORD) PALLETE RAM BANK 7 OBJECT RAM (WORD)

Page 14

(4)

(6)

(7)

(8)

(9) If ROM(s) is(are) defective, “ROM NG OO win appear on the screen.

When RAM's and ROM's are found all good after completing this RAM and ROM TEST, you can move over to the next test item by pressing the 1P and 2P start buttons.

In case any RAM(s) or ROM(s) is(are) found faulty after completing the RAM and ROM TEST, press the 1P start button to repeat the test. Press the 2P start button to go to the next test.

Display of the Test Items The following test items are shown so that you may select a test item you want by moving the 1P joystick up and down: 1/0 SOUND CHARACTER COLOR CROSS HATCH OPTION EXIT NOaRON> Press the Attack button to get the test indicated in red started. Press the 1P and 2P start buttons to end the same test.Press the 1P start button to start “OPTION” test.

1/0 Port Test

The status when each joystick, button, and coin is turned “ON” is shown. 8765432187654321 IN PORT 1 0000000000000000 IN PORT 2 0000000000000000 IN PORT 3 0000000000000000 DIP SW 0000000010000000 (O-OFF, 1-ON)

Sound Test

The screen shows the number of each sound and the test is made about whether the corresponding sound is given. Push down the 1P joystick to move over to the next sound's test. Character Test

The player character is displayed in the center of the screen.

ie rai Make sure that the character is shown vertically and horizontally

reversed as shown on the left. Pa

Color Test

By moving down the 1P joystick, the test can be advanced like 1—2—3—4—5—6 —7—8 —1

The whole screen shows only blue color. The whole screen shows only red color. The whole screen shows only magenta color. The whole screen shows only green color. The whole screen shows only cyan color. The whole screen shows only yellow color. The whole screen shows only white color. A color pattern is displayed as illustrated on the right.

CROSS HATCH TEST

The white lines represent CROSS HATCH PATTERN on the screen.

BLUE

RED

MAGENTA

GREEN

CYAN

YELLOW WHITE ONADRWN= BLACK

Page 15

NOTE: SET DIP SWITCHES FOR

4 PLAYER UPRIGHT.

USE EITHER UPRIGHT A OR UPRIGHT B

TO SELECT EITHER

COMMON OR INDIVIDUAL

COIN ENTRIES

SET 2 PLAYER DIFFICULTY ON NORMAL, SET 4 PLAYER DIFFICULTY

ON EASY PLAYER4 PLAYERS Oo START2 io) STARTL PLAYERL

° CN4 4 PLAYER JAMMA CONNECTOR COMPONENT SIDE ATOMIC PUNK PCB

Page 16

ISOLATION

3 AMP. VARISTOR T ee RAMSFORMER 410 VAC FUSE ON/OFF. cORCOM

SWITCH EMI FILTER

Bb on 11 AMP

SWITCHING

GROUND

+5 vpC

110 vac * -5 vpc +12 VDC

COIN COUNTERS

COUNTER

8 OHM SPEAKER L AUDIO AUDIO +

RGB COLOR MONITOR aaa >TO VIDEO RED N VIDEO GREEN VIDEO BLUE NEG CMP. SYNC VIDEO GROUND

HORIZONTAL MOUNT = SYNC

a COIN SWITCHES COIN INPUT #1 COIN INPUT #2

COIN DOOR LIGHTS #44 BULBS 1ST PLAYER CONTROLS SHOWN >= CAP ¢2P> 17 1P START u 2P START 21 RIGHT 20 LEFT 19 DOWN 18 uP Bome. REMOTE >xXE> NG

Sa [alae od ui EHoLeE

No” OF cee 27,28,e,f GROUND

gl.

tt ATOMIC PUNK = USE CONNECTOR CNZ & CNG

NOTE: RECOMMENDED DIFFICULTY FOR 3RD & 4TH PLAYER

2 PLAYER = NORMAL DIFFICULTY 4 PLAYER = EASY DIFFICULTY

Page 17

ATOMIC PUNK II Instructions:

FY Tap A BUTTON to PLACE BOMBS

Bomb

pF, Tap B BUTTON to EXPLODE REMOTE BOMBS

Remote

4-WAY JOYSTICK

(ONLY) Game will not play properly with 8-way joysticks.

p , Y Tap A BUTTON to PLACE BOMBS

yf Tap B BUTTON to EXPLODE REMOTE BOMBS