CATHODE RAY TOMES

Victory Road

Victory Road (SNK, 1986) · Document · 15 pages · 14 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

USER INFORMATION ~ F.C.C-

THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO

FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE

WITH THE INSTRUCTIONS MANUAL, MAY CAUSE INTERFERENCE TO

RADIO COMMUNICATIONS.

IT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS "A" COMPUTING DEVICE PURSUANT TO SUB-PART J OF PART 15 OF F.C.C. RULES, WHICH ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINS‘ SUCH INTERFERENCE WHEN OPERATED IN A COMMERCIAL ENVIROMENT

IN A COMMERCIAL ENVIROMENT.

OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA 1S

LIKELY TO CAUSE INTERFERENCE IN WHICH CASE THE USER AT HIS

BE REQUIRED TO CORRECT THE INTERFERENCE.

Page 3

INTRODUCTION

"VICTORY ROAD" is a microprocessor based coin-operated electronic game that makes extensive use of digital integrated circuitry and television monitor concepts. This Manual is designed for the use of maintenance technicians who »ossess a general knowledge of solid-state circuitry and video monitor theory. Any individual NOT knowledgeable in these areas SHOULD NOT attempt repair of the electronic portions of the game.

In addition to this manual and training in electronics, troubleshooting and repair will be facilitated by access to generaltype handtools, a multimeter, a 50 or 100 MHZ oscilloscope and a logic probe would be helpful.

Technical assistance is available at your Tradewest Distributor.

Questions or comments concerning "Victory Road" are welcome and should be directed to

TRADEWEST, INC. 2400 South Highway 75 Corsicana, Texas 75110

Page 4

HOW TO PLAY

1P or 2P game

2nd player can join the game anytime after the lst player starts and either player can join anytime and any stage during playing. Control players' HERO by Joystick (LS-30) and 2-firing buttons. Control direction of players' HERO by 8-way Joystick and control direction of firing by rotating switch. Players' HERO will be protected ocassionally with armor when player get "POW" appears from earths' surface. Right firing button is for GRENADE only. Operate left firing button for many other weapons.

Get POWER POINTS hidden inside of Rocks, Walls and Pyramids, etc. Thunder : "SUPER POWER"....All enemies can be destroyed. Earthquake: Stops all enemies' action. Eye Mark : Secret "POW" appears in sight. Key : This key allows you to move through the multidimentional space. Star mark : Watch the angel, it tells you which "Pow" will help you.

Dozens of "POW" are hidden in secret place.

Player can destroy almost obstacles in sight. Select your weapons : Sword, boomerang, bazooka, hand grenades, machine gun, etc.

Become a master with your sword. It will.destroy your enemies and stop their bullets. When your super-powered lightening swords are crossed, you will discover a secret power.

Watch the panels flying from multi-dimeritional space. If you touch these panels, you will be lost in the Black Hole.

CONTINUE PLAY

Receive additional warriors during play by inserting coin and and pushing 1 or 2 player button. You can play continuously from the stage finished the game by inserting coin and pushing start button within 10 seconds after indication of "GAME OVER".

Page 5

HARNESS CONNECTOR CR7E-56DA-3.96E CRS) 3.96mm Pitch

a)PARTS SIDE(28)
ollsJo]
(A)SOLDER SIDE(ry
SOLDER SIDEPIN NO.PARTS SIDE
GNDA 1GND
GND‘|B 2GND
+5Vc 3+5V
+5VD 4+5V
-BVvE 5-5V
+12VF 6+12V,

IN-CORRECT INSERT PREVENTING KEY u 7 | IN-CORRECT INSERT PREVENTING KEY COIN COUNTER 2 J 8 COIN COUNTER 1

K 9

SPEAKER (-) L |10 SPEAKER (+)

M |11

VIDEO GREENN |12VIDEO RED
VIDEO SYNCP 13|VIDEO BLUE

SERVICE SWITCH |R [14 VIDEO GND [8 15 |

COIN SWITCH 2 T |16 COIN SWITCH 1

START SWITCH 2 |U [17 START SWITCH 1

2P CONTROL 1 UP vy |18/1P CONTROL 1 UP

2P CONTROL 2 DOWN w |19]1P CONTROL 2 DOWN

2P CONTROL 3 LEFT xX |20]/1P CONTROL 3 LEFT

2P CONTROL 4 RIGHT |Y |21]1P CONTROL 4 RIGHT

2P CONTROL 6& PUSH! |Z |22|/1P CONTROL 5 PUSII1 2P CONTROL 6 PUSH2 |a |23/1P CONTROL 6 PUSH2

b |24

~ te jas

d |26

GNDe |27“cnDCS
[GNDTy [a8GND
Page 6

DIP SWITCH OPTIONAL DIP SWITCH SETTINGS

DIP SW No.

ITEMSPECIFICATION12345678

UNITED STATES ON

GAME STYLE UPRIGHT OFF

® EVERY BONUS OFF BONUS %* SECOND BONUS ON

3 OFF NUMBER OF HERQ]| |--—————__——. }—— 5 4 ON 1 COIN 1 PLAY OFF | OFF PLAY FEE —=— +

2 COIN 1 PLAYONOFF

COIN 1 ——} 3 COIN 1 PLAY OFF | ON

4 COIN 1 PLAYONON

1 COIN & PLAY OFF | OFF

PLAY FEE1 COIN 4 PLAYON | OFF
COIN 2I COIN 3 PLAYOFF JON

1 COJN.2. PLAY. ON [ON

  • EVERY BONUS-++++CREDIT EACH ONE HERO {N EVERY 2X0 BONUS.
  • SECOND BONUS+++*CREDIT ONE HERO AT IST AND 2D BONUS ONLY. NO FURTHER HERO CREDITED AFTERWARD.
Page 7

OPTIONAL DIP SWITCH SETTINGS

Dip Switch No.2

GAME LEVEL OF DIFFICULTY —~ DIP SW NO. 2

ITEMSPECIFICATION]1]2]3!46|7|8

EASY OFF | OFF GANE LEVEL OF NORMAL ~ JON | OFF DIFFICULTY HARD OFF | ON DIFFICULT ON | ON

ATTRACTIONWITHOUT SOUNDOFF

SOUND OFF WITIL ATTRACTION SOUND ON

MONITORSTOP VIDEO DISPLAYon | ON

ETTING NEVER FINISH OFF | ON 50000/100000 OFF BONUS | ———______,

POINTS60000/120000OFF

SETTING

IST/2ND’1000007200000ON

NO BONUS ON | ON CONTINUE WITHOUT CONTINUE ore | PLAY WITIE CONTINUE ON

OFF

Page 8

INSTALLATION

YOUR GAME WAS SHIPPED FROM THE FACTORY IN READY-TO-

PLAY CONDITION.

A BRIEF INSPECTION IS SUGGESTED BEFORE THE MACHINE IS REMOVED

FROM THE CARTON. IF THERE IS DAMAGE TO THE SHIPPING CARTON,

CONTACT THE FREIGHT CARRIER FOR CLAIM PURPOSES. EXTERNAL

DAMAGE COULD INDICATE POSSIBLE DAMAGE TO THE CABINET AND/OR

ELECTRONIC COMPONENTS.

AFTER THE CARTON HAS BEEN SATISFACTORILY INSPECTED, REMOVE

THE MACHINE FROM THE SHIPPING CARTON.

EXAMINE THE INTERIOR OF THE GAME FOR DISCONNECTED WIRES,

CABLES OR HARNESSES. MAKE SURE THE ELECTRONIC DEVICES ARE

SECURELY MOUNTED IN THEIR SOCKETS, ETC. RECORD ANY PROBLEM

AND CONTACT YOUR CUSTOMER SERVICE REPRESENTATIVE FOR TECH-

NICAL ASSISTANCE.

ELECTRICAL REQUIREMENTS

UNLESS OTHERWISE SPECIFIED, THIS GAME IS SET TO OPERATE AT

110 VOLTS A.C.

Page 9

ROUTINE MAINTENANCE & SERVICE

Because of the solid state electronic circuitry, this machine should require very little maintenance, and only occassional adjustment. However, it is necessary to take steps to insure this.

The Game volume controls are located on the printed circuit board and can be accessed through the rear cabinet door.

The video monitor was properly adjusted for best color and sharp picture display before shipping. Occassionally minor adjustments are necessary. All adjustment controls for the monitor are located on the rear of the monitor assembly.

This machine should only be adjusted by a "Qualified" Technician. “DO NOT MAKE ANY ADJUSTMENTS ON THIS MACHINE WHILE THE POWER IS ON.!"

POWER SUPPLY

The Computer Board in this game operates most efficiently and reliably when the power supply is set so the voltage on the Board is +5.0 volts. To check voltage, place a digital multimeter across +5 volts (pin-3, pin-4) and ground (27,28) on the P.C. Board edge connector. Adjust, if necessary, the +5 volt Pot (control) located on the power supply so the meter reads between +4.9 and +5.1 volts.

FOR SERVICE INFORMATION CONTACT:

Your Local

Tradewest Distributor

or

Tradewest, Inc. Attn: Service

214/874-2683

Page 10

BOARD DIAGNOSTIC TEST P.Cc.

A MANUAL TEST MAY BE PERFORMED BY DEPRESSING THE "PLAYER 1" START BUTTON DURING POWER-UP. WHEN THE "CROSS-HATCH" PATTERN

APPEARS, RELEASE THE BUTTON AND PROCEED AS FOLLOWS:

1.COLOR

LIL

RED GREEN BLUE Picture 1 "Cross Hatch"

Adjustment to the monitor may be made to center and/or extend the borders of the picture.

Press "PLAYER 1" button to

change to picture 2.

Picture 2 "Color Test"

Adjustment of colors on the monitor may be made.

Press "PLAYER 1" button to

change to picture 3.

Page 11
  • LEVER

PL uP a PLP O

PL DUNN O P2 DOWN O PL_RIGHT O PZ. RIGHT O PL LEFT O | P2LEFT O Py NORU O P2 NOB O

PL PUSHIO = P2PUSHIO Pi PUSH20 F2 PUSH20

COIN O PLAY2 O

  • Mone

\2345678

00000000

\234S618

0000000

TYPE TABLE

HERO 3

VCOINT PLAY (CoN 2 GRAY BONUS! SOn00P

RONUS2 100000 EVERY

LEVEL | ‘Picture 3 "Joystick & Switch Test"

The screen will display all switches with a zero (0) to the right. The zero (0) should change to one (1) and increase by one each time Joystick is moved to the right. Moving Joystick to the left decreases each number by one. Inserting coin or pushing service switch increases coin number by one.

Press “PLAYER 1" button to change to picture 4.

Picture 4 "Mode Check"

The screen will automatically display all programmable features with their respective settings. Settings should correspond to the position of the dip switches on the P.C. Board. The actual set mode is dis-

played at the bottom of the screen.

Press "PLAYER 1" button to change to picute 5.

Page 12

PECTURE 5

PICTURE 6

  • FRONT

COLOR 00

FRONT CHARACTOR

  • SOUND

SOUND CODE

MUSIC 41-7B

EFECT 81-BB

VOICE CO-FF

STOP OF PICTURE 5. FRONT TEST Confirm if Characters are displayed on the monitor.

PICTURE 6 SOUND TEST Set up Music Code ("2" of Picture 6) to 41-7B or 81-BB or CO-FF by lever and push firing button. Then music or effective sound; or voice comes out. If you wish to stop it, set up Music Code to OE and push firing button.

Page 13

Ls30 - 24 JOYSTICK ASSEMBLY

PARTS NAME

gawp

LS30- LS30- LS30- LS30- LS30- LS30- LS30- LS30-10 LS30-11 LS30-12 LS30-13 1LS30-14 LS30-15 LS30-16 LS30-17 LS30-18 LS30-18H LS30-19 LS30-20 LS30-21 LS 30-22 Ls30-24 wovuaueun Knob Cap Knut (M6) Knob (Main Boday) Fastener Lever mask Main guide Micro Switch Plate Micro Switch 9g C-Clip Spacer (B) Spacer (A) Washer (small) Shaft Holder Shaft Holder Stand Washer (large) Spring 124 C-Clip Shaft Star Washer Rotary Switch Installation Plate (SUS) Rotary Switch Harness Rotary Switch Stopper Stand Steel Base Knob setting tool Complete Assembly

Page 14

Pe. Cc . B. SPECIFICATIONS

1 EDGE CONNECTOR CR7E-56DA-3. 96E(56PIN) 2 SWITCHING DC +5V 7A REGURATOR pC +12V 1A DC -5V¥ 1A

*Use with voltage on P.C.B. between the range of +5.00V -- +5.10V

oO A6001UP02 oy ®)

SOUND VOLUME —t

Turn clockwise for volume up of Whole sounds.

= | PARTS SIDE TO CABINET

_\ DIP SWITCH —

VOLTAGE ADJUSTING LED

the voltage is correct. “TS ooel Turn on 2 LED lights, when CN 7

Even if Solid State Module is clearly found defective, please do not check Circuit with a Tester, etc. The ICs may be destroyed by the voltage of a Tester.

Turn on 2 LED lights, when the voltage is correct. If only one LED light turns on, adjust by 5VADJVR of switching regurator. When no LED light turns on, check electric voltage of power source.

Don't forget to cut off Power Source when you change Parts or insert/pull off of Connector.

Please be sure to Disconnect Power Source by pulling Plug. (Not by Cord)

Be careful for handling Monitor and it's part of High Tension.

Page 15

A lot of ICs and Memories are used, by which Electric power

consumption for +5V (Volts) is about 5A ( res).

Please connect P.C.B. to Cabinet and adjust electric voltage of

Power Source to be +5V at each Edge Connector (56pin) of P.C.B.

Power Source to be +5V at each Edge Connector (56pin) of P.C.B In case voltage does not indicate more than +5V even by fully

adjusted by sree esate .

ae = because of insufficient Power Source or lack of eae

° ectric Current. So, please change Power Supply of which rated voltage is higher

rated voltage is higher.

For +5V, please use sufficient cable (1.25mm x 2 or 3.5mm) which is capable for Electric Currency. Voltage of intermediate Harness descend by contact resistance, so please avoid to connect several intermediate Harnesses to keep sufficient voltage. = ; If +6V Coin counter is connected from +5V, which causes Voltage drop, so please use +12V Coin Counter.