CATHODE RAY TOMES

Bubbles Instruction Manual (16-3012-101)

Bubbles (Williams, 1982) · Instruction Manual · 29 pages · 35 sections · original scan

Page 1

16-3012-101

Instruction Manual

Page 2

ROM

BUBBLES 4B

BUBBLES 2B

BUBBLES 3B

BUBBLES 4B

BUBBLES 58

BUBBLES 6B

BUBBLES 7B

BUBBLES 88

BUBBLES 9B

BUBBLES 403

BUBBLES 44B

BUBBLES 12B

Special Chip 4

Decoder ROM 4 (Horizontal)

Decoder ROM 6 (Vertical)

ROM 43 (Sound)

ROM SUMMARY

PART NO.

A-5343-10141-B

A-5343-10412-B

A-5343-10413-B

A-5343-40114-B

A-5343-10115-B

A-5343-10416-B

A-5343-10147-B

A-5343-10118-B

A-5343-10119-B

A-5343-10120-B

A-5343-10121-B

A-5343-10122-B

A-5410-09944

A-5342-09694

A-5342-09821

A-5343-10127 DESCRIPTION

PROM, 4Kx8, BROWN LABEL PROM, 4Kx8, BROWN LABEL PROM, 4Kx8, BROWN LABEL Special Chip

PROM, 512x8

PROM, 542x8

ROM, 4Kx8 Loc.

4E

4c

SE

5A

6E

6C

7A

7c

TE

4F & 2F

3c

3G

IC42 BOARD

ROM

ROM

ROM

ROM

ROM

ROM

ROM

ROM

ROM

ROM

ROM

ROM

ROM

CPU

CPU

SOUND

Page 3

INSTRUCTION MANUAL

FOR UPRIGHT AND TABLE GAMES

including...

* operation ¢ bookkeeping ¢ adjustment ¢ diagnostics

° parts

Page 4

CONTENTS

@CHAPTER 1 Game Setup Warnings & Notices..............c cece cet e een e eens 5 Examine Your GaMe........ 6. cece cence e tenet eee e eee 5 Location of Controls......... 0.0 cee teen eee eee e ee 6

@CHAPTER 2 Game Operation

Power Turn-On..

Game Operation.

Bookkeeping Total:

Game Adjustments

Definitions of Pricing Terms

@CHAPTER 3 Troubleshooting Procedures

IMtrOdUCTION .... 2. cece cece eee cece enter nner ees 14

POWErUD Tests... 0... cece eee eee eee eee ete e tet e neta eee ee es 15 +5VDC Power Supply Adjustments. .........0..-2-- cece ee ee renee 15 Self-DIGQNOSHICS. ... 6... n tenet eaten 15 Diagnostic Mode Tests .............0:e esse eee eee eect eee eee ene 6 Sound Board Diagnostics.......- 666.6. ce cece cece e eects 18

CMOS RAM Data Test Protocol ...... 6... 6c cece eee rete ees 20

@CHAPTER 4 Parts

Page 5

CHAPTER 1 Game Setup

Warnings & Notices

Examine Your Game

Location of Controls

Page 6

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 7

Warnings & Notices

WARNING:

4, FOR SAFETY AND RELIABILITY, WILLIAMS does not recommend or authorize any substitute parts or modifications of WILLIAMS equipment.

  • USE OF NON-WILLIAMS PARTS and modifications of game circuitry may adversely affect game play, or may cause injuries.
  • SUBSTITUTE PARTS, MODIFICATIONS AND GAME “CONVERSIONS” may void FCC type-acceptance.
  • SINCE THIS GAME IS PROTECTED by Federal copytight, trademark and patent laws, so-called game “conversions” may be illegal under Federal law.
  • THIS “CONVERSION” PRINCIPLE ALSO APPLIES to unauthorized facsimiles of WILLIAMS equipment, logos, designs, publications, assemblies and games (or game features not deemed to be in the public domain), whether manufactured with WILLIAMS components or not.

RF INTERFERENCE NOTICE:

CABLE HARNESS PLACEMENTS AND GROUND STRAP ROUTING on this game have been designed to keep RF radiation and conduction within levels accepted by FCC regulations.

TO MAINTAIN THESE LEVELS, reposition harnesses and reconnect ground straps to their original placements if they should be disconnected during maintenance.

Examine Your Game

When you receive a new WILLIAMS game, examine it carefully before you power if up. Be sure it was delivered in good condition!

LIINSPECT THE OUTSIDE of the shipping carton and/or game cabinet for shipping damage,

[JUPRIGHTS: UNLOCK AND SET ASIDE THE TOP-REAR PANEL. Undo the two frunk latches on the inside of the bottom door. Open the door. Now check circuitry.

LITABLE GAMES: Unlock the component door on the Player 2 side of the game. Carefully lower the door to the floor.

(CJARE CONNECTORS SECURELY ATTACHED? Reconnect any found loose. DON'T FORCE CONNECTORS. They're keyed and only fit one way. By the same token, take care: reversed edge-connectors can damage PC boards!

CIARE PLUG-IN CHIPS FIRMLY-SEATED in their sockets?

CUUNWRAP THE POWER CORD coiled inside the cabinet. Now position the cord in the wood slot beneath the bottom door. (Table games: Drop the plug through the hole in the floor, DON'T PLUG IT IN YET!

CISCRUTINIZE MAJOR SUBASSEMBLIES, such as the monitor, contol panel, transformer board and power supply. Make sure they're securely-mounted.

Page 8

Location Of Controls

THE ON-OFF SWITCH is situated on the top-left corner of upright games as you face the back of the cabinet. Table games have an on-off switch underneath the game.

THE VOLUME CONTROL in upright games is located inside the coin door and on the right cabinet wall os you face the game.

DIAGNOSTIC SWITCHES are on the back of the coin door in upright games. In table games they're under the hood and on the top-righi side as you face the front of the game.

These switches are used to access the Diagnostic- Mode Tests, the BOOKKEEPING TOTALS screen and the GAME ADJUSTMENTS screen. Refer to the appropriate sections below for information on each of these impor- OTHER CONTROLS. Finally there are five more controls that are used somewhat less often that those above:

  • The memory-protect interlock switch is near the diagnostic switch bracket (see above). This switch must be open when you clear BOOKKEEPING TOTALS ot make GAME ADJUSTMENTS. It automatically opens when the coin door is open on upright or mini games and when the hood is up on cockpit games.
  • The GPU board reset switch is located across the CPU board from the batteries respective boards.
  • The cashbox advance switch, found inside the cashbox door on all models, allows bookkeeping information to be audited without permitting it to be zeroed.
Page 9

CHAPTER 2 Game Operation

Power Turn-On

Game Operation Bookkeeping Totals Game Adjustments

Definitions of Pricing Terms

Page 10

Power Turn-on

CAUTION: This game must be plugged into a properly-grounded outlet to prevent shock hazard and to ensure proper game operation. DO NOT use a “cheater” plug to defeat the ground pin on the line cord, and DO NOT cut off the ground pin.

WHEN THE GAME IS FIRST TURNED ON it produces a sound. Simultaneously general illumination should come on and a moment later a scanning “rug pattern” indicating the RAM test should appear on the screen. Next the rug should become stationary as the ROM test is performed.

IN A CORRECTLY-RUNNING GAME the rug pattern will be followed by the message “INITIAL CHECKS INDI- CATE ALL SYSTEMS GO". If RAM or ROM failure messages come up on the screen instead, refer to Power Up Tests in TROUBLESHOOTING PROCEDURES.

Game Operation

GAME START

Insert coins; a random sound is produced and credits are displayed on the CRT. With two or more credits displayed, pressing 2-player start initiates a 2-player, 3-turn game.*

THE JOYSTICK guides our noble protagonist (the bubble) around the sink in any of eight directions: N-NE-E-SE-S-SW-W-NW. The bubble is a slippery fellow, so action is slightly damped.

AT LAST, THE GAME THAT HAS EVERYTHING. ..including the kitchen sink! The player is represented by a growing bubble. There are three bubbles per game (adjustable feature). The object of the game is io clean up “crums”, greasies and ants by floating over them.

Each one so disposed of makes for a bigger, more imposing bubble. The end of each round is signaled by a whirlpool. A bonus based on bubble size is awarded after the whirlpool.

BUT THE SOAP OPERA CONTINUES: Briny brushes and spiny sponges cavort in the sink among iestless razor blades and rambling roaches. Beware! They can sap your suds or even soak you for your turn if the bubble fouches one! Be careful too, not to fall down the drain (or your bubble will burst)!

A large bubble can touch these enemies, but if it does it will shrink, forfeiting bonus points. Small bubbles will be absorbed by these enemies...and you'll be washed up until your next turn! Any bubble that touches razor blades or sharp objects is wiped out.

*adjustable feature TURN THE TIDE! Picking up the broom from the cleaning lady scores a bonus. You must have the broom to fend off a roach. If the broom is not pointing at the roach, he can swill down the bubble and cause you fo lose a turn.

When the sink is clean, the drain will flash green. The bubble should then be large enough so that it can plunge down the drain to. the next sink. If the bubble doesn’t have a mouth, it isn't big enough and will be swept down the drain instead, sacrificing one turn.

HIGH SCORE SIGNATURE

Select letters with the joystick. Push right fo move forward through the alphabet; push left to move backward. Then push the joystick up to lock in the letter.

Bookkeeping Totals

  • In Game-Over Mode, open the cashbox and depress the cashbox advance swiich. The advance switch located on the diagnostic switch bracket can also be used. (See Figure 1.) The CRT should indicate all bookkeeping and evaluation totals. If so, go to step 3. If the CRT display comes up in the ROM test, perform step 2.

AUTO-UP O@0O HIGH MANUAL- ADVANCE: SCORE DOWN RESET

Figure 1. Diagnostic Button Switches

2, Continue to depress the cashbox advance switch, stepping the game through test programs for ROMs, RAMs, CMOS RAM, sounds switches, color RAMs, and then CRT test patterns, of which there are five. The fifth test pattern, color bars, directly precedes the CRT display of the bookkeeping and evaluation totals.

  • The bookkeeping and evaluation totals appear on the CRT as in Figure 2.

CLEARING BOOKKEEPING TOTALS

Depress ADVANCE to display Game Adjustments. 2, Use the joystick to position the cursor beside CLEAR BOOKKEEPING TOTALS (Figure 3).

  • Push the 2-PLAYER button.
  • Depress ADVANCE.
Page 11

BOOKKEEPING TOTALS

LEFT SLOT COINS CENTER SLOT COINS a RIGHT SLOT COINS PAID CREDITS FREE MEN TOTAL TIME IN MINUTES TOTAL MEN PLAYED TOTAL SINGLE PLAYER TOTAL DUAL PLAYER TOTAL CREDITS PLAYED

AVERAGE TIME PER CREDIT

Figure 2, Bookkeeping display

IF AVERAGE TIME PER CREDIT RUNS BELOW 1:30 (Figure 2), then more liberal settings are recommended. What if AVERAGE TIME PER CREDIT runs over 2:30? Make the game tougher. Always try to keep AVERAGE TIME PER CREDIT close to the ideal of 2:00.

Game Adjustments In the Game-Over Mode open the coin door. With the

AUTO-UP/MANUAL-DOWN switch set fo AUTO-UP, depress the coin door ADVANCE switch twice to cause a CRT display as shown in Figure 3.

SELECT THE FUNCTION YOU WISH to change by moving the joystick (push up to move the arrow up, down to move the arrow down). Then, making sure the coin door is open, push the 2-PLAYER button to increase or the 4-PLAYER button to reduce the value of the selected function. [Select the appropriate difficulty level by using the 4-PLAYER (easier) and 2-PLAYER (harder) buttons (O=easiest or liberal, 5=average, 9=hardest or conservative).

For a shorter game, increase the bonus points figure (EXTRA MAN EVERY). For a longer game, reduce it. (4,000 = long/99,000 = shor').

(For a shorter game, decrease the number of MEN FOR 4 CREDIT GAME. For a longer game, increase the number. (1=short/99 =long).

GAME PRICING is selected with standard settings or with custom settings as shown in Table 4. Note that free play can be elected by entering the code number 9 at the PRICING SELECTION function.

FOR STANDARD SETTINGS you need change only the PRICING SELECTION. For custom settings, first set PRIC- ING SELECTION to zero and then set the remaining values according to Table 4.

Page 12

GAME ADJUSTMENTS

EXTRA MAN EVERY 20,000 MEN FOR 1 CREDIT GAME 3 HIGH SCORE TO DATE ALLOWED YES PRICING SELECTION LEFT SLOT UNITS CENTER SLOT UNITS RIGHT SLOT UNITS UNITS REQUIRED FOR CREDIT UNITS REQUIRED FOR BONUS CREDIT MINIMUM UNITS FOR ANY CREDIT DIFFICULTY OF PLAY LETTERS FOR HIGHEST SCORE RESTORE FACTORY SETTINGS CLEAR BOOKKEEPING TOTALS HIGH SCORE TABLE RESET AUTO CYCLE SET ATTRACT MODE MESSAGE SET HIGHEST SCORE NAME USE 'MOVE' TO SELECT ADJUSTMENT USE ‘CREDIT’ BUTTONS TO CHANGE THE VALUE PRESS ADVANCE TO EXIT

Figure 3. Game adjustments showing factory settings

HIGHEST SCORE SIGNATURE

The number of letters allowed the highest-scoring player for entering his name can be varied from 3 to 20 and is recommended as 3. If objectionable words are entered as the signature name, you can change the lettered entry leaving the highest score the same. See Setting Highest Score Name.

RESTORE FACTORY SETTINGS

  • Position the cursor beside RESTORE FACTORY SETTTINGS. 2, Push the 2-PLAYER button.
  • Depress ADVANCE twice.

RESETTING HIGH SCORE TABLE

  • Position the cursor beside RESET HIGH SCORE TABLE. 2, Push the 2-PLAYER button.
  • Depress ADVANCE. SETTING ATTRACT MODE MESSAGE
  • Position the cursor beside SET ATTRACT MODE MESSAGE. Push the 2-PLAYER button. Depress ADVANCE. Enter up to two lines of your message following instructions on the screen.
  • Depress ADVANCE to enter Game-Over Mode. REN

To restore the Williams attract mode message, perform steps 1 through 3 and then turn the game OFF and back ON.

SETTING HIGHEST SCORE NAME

Position the cursor beside SET HIGHEST SCORE NAME.

  • Push the 2-PLAYER button.
  • Depress ADVANCE.
  • Enter the new signature.
  • Depress ADVANCE to enter Game-Over Mode.

An alternate, simpler method enters the factory highest score signature. In the Game-Over Mode, hold HIGH SCORE RESET down. After a few seconds a sound Is produced and the factory highest score signature has been activated.

Page 13

Table 1. Game Pricing

Units Min,

. Req'd Units

LettCenter | RightUnitsForFor
Coin DoorCredits/PricingSlotSlot$IPerBonusAny
MechanismMoneySelection | _UnitsUnits | Credit | Creait_ | Creait
Twin Quarter11256, S/S0444440
Quarter, Dollar,21506, 5/$40444442
Quarter01/25¢, 4/$43444409
21506, 4/640444102
11506, 3/$4, 4/51.250323450
11500, 3/$4, 75201248424%24
©4/50¢, 3/$4, 6/$24441240
01/5065441200
1DM, 5DM©4/1DM, 6/50M26011°0
20-Cent, 50-Cent11206, 3/5060608500
4 Frane, 5 Franc©4/2F, 3/5F only4116620
25 Cent,04/256, ANG64044°0
4 Guilder11286, SAG04a4440
5 Franc4/5F, 240F7102400
40 Franco4/40F81°2200
4 Franc, 2 Franco2/4F, 5/2F26044°(|
400 Lire, 200 Lire4/200 Lire84022°0
Twin Coin4/1 Coin34414oo
4/2 Coins5141:206
413 Coins, 2/5 Coins0202500
|04/2, 3/54466200
4-Unit, 5-Unit44, 550405400
113, 2502010500
‘Any¢Free Play9144400

Definitions Of Pricing Terms

PRICING SELECTION allows a shorthand method of setting the pricing functions. ff a number from one to nine is entered into the PRICING SELECTION function, a corresponding standard setting (shown in bold type above) will be entered into the game. The rest of the pricing functions are automatically set for that standard.

THE PRICE OF ONE GAME (number of coins per game) is equal to the number of SLOT UNITS for any one slot divided by the number of UNITS PER CREDIT. If the number of LEFT SLOT UNITS (or RIGHT SLOT UNITS) equals X and the number of UNITS PER CREDIT equals Y, then the price ‘of one game is X/¥.

UNITS REQUIRED FOR BONUS CREDIT is the number of games that must be purchased before a free game is awarded.

MINIMUM UNITS FOR ANY CREDIT is the least number of coins allowed per game or games: Or. put another way, the MINIMUM UNITS FOR ANY CREDIT determines the

smallest number of whole games that may be paid for

at one time, For example if an operator wants to allow one play for a quarter but wishes to encourage multiple gameplaying, he may enter:

©*0” in the PRICING SELECTION function

This zero value automatically sets all pricing functions. However minimum units for any credit must be raised to “2" or higher value to achieve the operator's goal. Here are the rest of the functions as they should appear.

@*4” in the LEFT SLOT UNITS function “4” in the CENTER SLOT UNITS function *4” in the RIGHT SLOT UNTIS function @*0" in the UNITS REQUIRED FOR BONUS CREDIT function 4" in the UNITS PER CREDIT Function e@*2” in the MINIMUM UNITS FOR ANY CREDIT function

These values allow one game to be played for a quarter, but ONLY when two or more games are paid for at a time. Incidentally, the “4” in CENTER SLOT UNITS allows four games per dollar coin (center slot only). See *2/50¢, 4/$1” above.

"

Page 14

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 15

CHAPTER 3 Troubleshooting Procedures

Introduction

Power-Up Tests

+5VDC Power Supply Adjustments

Self-Diagnostics Diagnostic Mode Tests

Sound Board Diagnostics CMOS RAM Data Test Protocol

Page 16

INTRODUCTION

Certain types of game malfunctions may inhibit the game's shooting algorithm begins with Power-Up and continues until diagnostic or display faculties. Troubleshooting procedures Game Over Mode. All procedures can be performed with for most of these types of malfunctions as well as malfunctions minimal test equipment or merely by observing the game that permit self-diagnosis are covered below. Our trouble- itself.

POWER-UP TESTS

NO GENERAL NO INITIAL VIDEO CHECKING POWER ILLUMINATION (RUG PATTERN) SUPPLY BOARD

  • Check fuse F2 on power supply board.
  • Check for proper installation of jumpers W1, W2, W3 and/or resistor R27. (Some machines MAY NOT have on R27, Refer to your drawing set.)
  • Check 4P4/J4, 4P3/J3, 6P2/J2 and 6P3/J3.
  • If all the above don't turn up the probfem, check power supply board. {1) Press reset button on CPU Board.
  • Try RAM and ROM Diagnostic-Mode tests (see below),
  • Swap power supply board with one from known-good game.
  • It game plays, problem is on power supply board.
  • If these tests don't turn up the problem, check power supply board. {3} If game doesn't piay, check power transformer with voltmeter,
  • If known-good power supply is unavailable for tests above, check +5V, -5V and +42V outputs on power supply in game. Each MUST BE within 2% of rated output with less than 0.1% AC hum.

MORE POWER-UP TESTS

ROM BOARD LEDS RECOGNIZE CONDITION ROM BOARD LEDS IDENTIFY BAD CHIPS

GENERAL“0” means all(4) scanning rug patternIf any video (see left) is missing or
power-up tests2) stationary rug patternerror message is displayed, proceed
Passed(3) “INITIAL TESTS INDICATE ALL SYSTEMSto Diagnostic-Mode tests.

sor

  • Game-Over Mode
CMOS (See| *0" means tests“HIGH SCORE TABLE RESET"(1) Open coin door or tabletop and
Appendix a) | passed“BOOKKEEPING TOTALS CLEARED"turn power off and on,

"ADJUSTMENT FAILURE” “RESTORE FACTORY SETTINGS BY OPENING FRONT DOOR OR TABLETOP AND TURNING GAME ON AND OFF”

“0” means tests passed “FACTORY SETTINGS RESTORED" (2) Press ADVANCE. Game should return to Game-Over Mode.

BATTERY (See Appendix A} “0” means tests passed “HIGH SCORE TABLE RESET” “BOOKKEEPING TOTALS CLEARED" “ADJUSTMENT FAILURE” “RESTORE FACTORY SETTINGS BY OPENING FRONT DOOR OR TABLETOP. AND TURNING GAME ON AND OFF”

  • Open coin door or tabletop and turn power off and on. Or. press ADVANCE In either case, game should retuin to Game-Over Mode.
  • Check AA alkaline cells on CPU Board.
  • If problem persists, proceed with CMOS RAM test by putting the game into its Dlagnostle-Mode (see SELF-DIAGNOSTICS).

MEMORY PROTECT "0" means tests Passed “HIGH SCORE TABLE RESET” “BOOKKEEPING TOTALS CLEARED"

  • Making and breaking memory protect interlock switch, check with
INTERLOCK“ADJUSTMENT FAILURE”VOM and replace if faulty.
(See“RESTORE FACTORY SETTINGS(2) Replace if faulty: Memory protect

Appendix A) BY OPENING FRONT DOOR OR TABLETOP gates 6F, IC1, 1, or CMOS RAMS. AND TURNING GAME ON AND OFF"

SPECIAL CHIP | “O" means tests passed

  • scanning rug pattern
  • blank screen instead of “INITIAL TESTS INDICATE ALL SYSTEMS GO"
  • high score table with no scores
  • intro blank or program crash
  • Turn power off.
  • To find bad chip, replace 2 special chips one at a time with known good chips.
  • Turn machine on after each Teplacement and run through Power-Up Tests.
Page 17

+5VDC Power Supply Adjustments

Before adjusting the voltage output, always check at the output of the supply for AC hum. This hum should never rise above .005V on the +5VDC supply. If it does, consult your schematic drawing set for proper DC voltages throughout the circuit.

Test for these with the DC setting of your multimeter. Make a second check using the AC setting. Pay particular attention to readings at TP5 (top of capacitor C10). If the voltage here is low (less than +414VDC) or if you find excessive ripple (more than 700mVrms), teplace the capacitor.

If TPA is less than +4.95VDC remove R10. If TP4 is still less than +4.95VDC, then check precision resistors R25 and R26. If they are within the 1% tolerance, then check IC2.

Self-Diagnostics

If RAM or ROM failure messages are displayed on the CRT after the “rug pattern,” proceed with selfdiagnostics. Self-diagnostic procedures are controlled by the AUTO-UP/MANUAL-DOWN and ADVANCE switches. (See Figure 4.)

Set the AUTO-UP/MANUAL-DOWN switch to the MANUAL-DOWN position and depress the ADVANCE pushbutton. The game is now in its Diagnostic Mode and a ROM test is performed. With ROM test results present on the CRT display, set the AUTO-UP/MANUAL- DOWN switch to the AUTO-UP position. Depressing the ADVANCE pushbutton initiates the RAM test. Further tests (CMOS, sound, switch, color RAM and monitor test patterns) are encountered one after the other as the ADVANCE pushbutton is depressed (once more for each subsequent test).

MONITOR TEST PATTERNS (19"-Monitor Upright Games only.) For ease in monitor adjustments, the monitor may be slid back and the screen viewed in the CRT mirror on the inside-top of the cabinet.

Remove the two bolts and carefully slide the monitor back in its shelf. Secure the monitor in the extended Position by inserting the two bolts through holes provided at the left side of the monitor.

AUTO-CYCLE MODE. From the color bar pattern (or Game Over with the switch set to AUTO-UP) depress ADVANCE two times to display GAME ADJUSTMENTS.

  • Position the cursor beside AUTO CYCLE with the joystick and push the 2-PLAYER button.
  • Depress ADVANCE.
  • The system will now sequence through ROM, RAM, and CMOS RAM tests repeatedly. The coin door must be open during the Auto-Cycle test. If an error is detected, the test is terminated and the failure indication is displayed on the CRT.
  • To terminate the Auto-Cycle test, turn the game OFF and ON.

LEGEND: FIRST DESIGNATION (3K) IS CIRCUIT BOARD GRID REFERENCE. DESIGNATION IN PARENTHESIS DENOTES BANK NO. (1-3) AND CHIP NO. (1-8).

Figure 4. RAM Location and Numbering on CPU Board

Page 18

DIAGNOSTIC-MODE TESTS

“2" means ROM error 2-digit ROM chip no.

“1” means RAMertor | Bank no. first... then chip no. in bank (see figure 4) TEST ROM BOARD LEDS ROM BOARD LEDS RECOGNIZE IDENTIFY BAD CONDITION CHIPS VIDEO emer

"ROM ERROR” and ROM chip no.

“RAM ERROR’ followed by RAM bank no. and chip no. (Note: with multiple RAM failures this display may not appear)

  • Turn power off.
  • Replace suspected chip.
  • Check for these normal voltages on indicated RAM chip: -5/pin 4, +42/pin 8, +5/pin 9.
  • Turn power off.
  • Replace suspected chip.
  • With multiple RAM failures always check Power supply. See POWER-UP TESTS.

CMOS (see appendix A) "3" means CMOS RAM error “CMOS RAM ERROR OR WRITE PROTECT FAILURE”

  • With power off, check pin 18 of CMOS RAM for 3.2VDC minimum. If presen}, check or replace CMOS chips. If absent, replace AA alkaline cells.
  • With new alkaline cells and power off. check for 3.2V minimum at pin 18, If still absent, replace diodes D9 and D410.
  • Upon power-up and reentry into diagnostics it CMOS error message persists, check CMOS RAM memory protect and address decoding circuits with a logic probe.

Tests 4 and 7 provide sequential subtests. To stop automatic cycling set switch to MANUAL-DOWN, Depress ADVANCE in MANUAL-DOWN to step through subtests. LED indications are not made for these tests.

TEST & PROCEDURES REMEDY OR ADJUSTMENT

SOUND (lest 4) “SOUND LINE 1” “SOUND LINE 2” “SOUND LINE 3° “SOUND LINE 4” “SOUND LINE 5” “SOUND LINE 6” (These appear one at a time) MISSING — CHECK 2P4/10P3 pin 3 2P440P3 pin 2 2P4/10P3 pin 2P4/40P3 pin 4 2P4/40P3 pin 7 2P4/10P3 pin 6 perform Sound Board Diagnostics (see below)

NOTE: If any two sounds are the same, check for a short between the select lines with the same sound. Qoanens

SWITCH CRT indicates AUTO-UP closed and any stuck (Refer to CABINET WIRING Diagram) (Test 5) switches. CRT Display for each Switch... () ROM BOARD SWITCH STUCK: Disconnect 2°3.

  • Set switch to MANUAL-DOWN ang DEM Beane INTERFADE BOARD (2) INTERFACE BOARD SWITCH STUCK: Disconnect clear any stuck switches. 3P2 ot 3P3,
  • CRT should indicate no switches ‘ADVANCE “PLAYER START (3) ROM BOARD SWITCH DOES NOT OPERATE: Closed. ‘AUTO-UP 2-PLAYER START Ground corresponding pin of 2P3.
  • Operate switches and check for HIGH SCORE MOVE UP 2 (4) INTERFACE BOARD SWITCH DOES NOT OPERATE: display of switch name. RESET MOVE DOWN 2 Ground corresponding pin of 3P2 or 3P3. Ler COIN Move Leet 2 [ISYMPTOM REMAINS SAME ... ROM Board of CENTER COIN MOVE RIGHT 2 te haat i o RIGHT COIN dine joard Faulty. SLAM SWITCH (SYMPTOM CLEARS UP ... Problem is in switches or wiring. ADDITIONAL TESTS FOR OPTO SWITCHES
  • Check that +5VDC is at pin 4 of 42P4,
  • With joystick in cenier position, check for 0.1V ‘at base of OFF transistor(s} (@1 thru Q4) and +5V at pin{s) 4, 2, 4 and 5 of 42P4.
  • With joystick moved from center position, check for 0.7V at base of transistor(s), and 0.1V at Corresponding pins 4, 2, 4 and § of 12P4.
Page 19

MORE DIAGNOSTIC MODE TESTS

TEST & PROCEDURESVIDEO SEQUENCESREMEDY OR ADJUSTMENT

COLOR RAM REPLACE RAM 4B REPLACE RAM 2B (Test 6)

Note that a blank sequence or two sequences with the same shade indicate a faulty 4A flip-flop, 1B RAM or 2B RAM or a failure in the color analog circuit. Check voltages on @1 (green transistor), Q2 (red transistor) and 4) light green screen | yellow band Q3 (blue transistor). During the eight full-screen color 5) green screen tests, the base voltage (center pin) on each transistor 6) dark green screen should vary between 3.8V (brightest color) and 4.4V (no color).

Color RAM Check

  • CRT sequences ‘through 8 colors,
  • light red screen too-light or
  • red screen too-dark red
  • dark red screen ‘or gray band magenta band

cyan band

7) light blue screenmagenta bandtoo-light or too
  • blue screen -dark blue or gray band
  • light green screen | green band dark green band 2 seconds each. or gray bond
\(2) Thick vertical5) green screenlight greendark green band
band indicatesband‘or gray band

color RAM fault.

  • dark green screen gray band

MONITOR Aids you in setting up & COLOR cross hatch pattern vertical and horizontal RAM linearity, convergence, and (Test 7) focus.

ted screen Aids you in optimizing green screen color purity. blue screen color pattern

color bars if color RAM test 6 +double-width indicates no faults, half-width symptoms at left suggest a Color Bar Pattern stransposed fault in 1A, 4B, 2B or 2C +missing Chips.

Page 20

SOUND BOARD DIAGNOSTICS

SYMPTOM TEST & PROCEDURES

| wissnis SOUNDS; CO CHECK SOUND-SELECT INPUTS

NO SOUND—STEP 4| TegrTooLCONDITION & REMEDY
(ASSUMPTION:Sound Boardlogic probe (game»PULSING-proceed
INPUT SECTIONconnector 40P3/J3-2on and in Test 4)*LOW-check jacks, foils

FAILURE) 'o7 *STILL LOW-perform ROM BOARD

checkbox.

SRA DIP resistorsVOM-reading ohmsALL 4.7K-proceed
R3-R9(game off)ANY OPEN-replace SR4
C3-C9VOM-teading ohms.ALL OKAY—proceed

(game off) *ANY SHORTED-repiace bad

15-4, 1C7-14logic probe (game.HIGH-proceed
{power pins)‘on and in Test 4)+LOW-replace C49 (IC5) or C24 (IC7)

STILL LOW-replace bad IC.

IC5-2, 4, 6, 10, 12, 15;logic probe (game«PULSING-ptoceed
1C7-4, 6‘on and in Test 4)+LOW-replace chip
1C10-18 and 19logic probe (game«PULSING-proceed
(PIA)on and In Test 4)sLOW-lift C20, retest

*PULSING NOW-replace C20 + STILL LOW-replace IC6, retest

140-10 to 17logic probe (game«PULSING-proceed
(PIA)‘on and In Test 4)*SOME LOW-replace IC

ALL LOW-lift C34, retest *PULSING NOW-rteplace C31 “STILL LOW-replace IC

Page 21

SYMPTOM

MISSING SOUNDS; NO SOUND—STEP 2

(ASSUMPTION: OFF-BOARD FAILURE)

NO SOUND

(ASSUMPTION: POWER SECTION FAILURE)

STILL NO SOUND

(ASSUMPTION: AUDIO SECTION FAILURE)

MISSING SOUNDS; NO SOUND

(ASSUMPTION: DIGITAL FAILURE) MORE SOUND BOARD DIAGNOSTICS

TEST & PROCEDURES

CO CHECK ROM BOARD OUTPUTS

  • If you hear game sounds, disconnect and then reconnect Sound Board connector 10P3/J3.
  • You should hear one or more game sounds. If so, put game in Diagnostic Mode Test 4 and proceed with this checkbox. If nof, go ahead fo POWER SUPPLY checkbox below.

TEST TOOL CONDITION & REMEDY

ROM Boardlogic probe (game«PULSING-repair cable to Sound
connector 2P4/J4-2on and in Test 4)Board

to7 *ANY LOW-repair jack oF foil, proceed

9C DIP resistors 2 to 8VOM-reading ohmsALL 4.7K-proceed

(game off) *ANY OPEN-replace 9C

40-53VOM-reading ohms»ALL OKAY-proceed

(game off) *ANY SHORTED-replace bad

8C-10 to 15 (PIA)logic probe (game»PULSING-proceed

on and in Test 4) *SOME LOW-teplace 8C

[1 CHECK ON-BOARD POWER SUPPLY

  • With power off, test for fuse continuity at F4 and F2.
  • With power on, check for +42V unregulated DC at TP4 and at pin 5 of IC4.
  • Now check for +5V regulated DC between TP4 and TP3. If voltages are absent or low, turn off game and lift one pin of filter capacitors C25, C26 and C27.
  • Check each with ohmmeter for possible shorts.
  • If capacitors are good and unregulated voltages test okay but you're missing +5¥, replace regulator chip (IC8). C1 CHECK AUDIO (ANALOG) SECTION
  • Turn power on; turn up volume control. Momentarily place powered-up AC. soldering pencil on final amplifier’s input pin (IC4, pin 4 or 40P4, pin 2). If you hear low hum, audio IC, volume pot and speaker are okay.
  • Repeat test at Q2 emitter. If you hear hum, analog section is okay. Step (1) will also work if you simply touch amplifier's input pin. However output level of hum will be much lower than with soldering iron. DO NOT use a soldering pencil of over 40 watts, Cordless models will NOT work here.

[1 CHECK SOUND ROM (1C42) AND RELATED CIRCUITRY

  • Turn power on.
  • lf you have no game sounds but power supply tests show normal voltages and no ripple on +5V, check crystal clock circuit. Using DVM or logic probe, test for pulsing AC across crystal. If clock signal's absent, replace crystal and associated capacitors.
  • Turn power off.
  • Swap sound ROM (IC42) and then microprocessor chip (IC9) with known-good Chips.
  • Power-up and test Sound Board after each swap by pushing DIAGNOSTIC button.
Page 22

CMOS RAM Data Test Protocol

The fitst sub-test of the CMOS RAM data is that of the ATTRACT MODE MESSAGE checksum. If the test does not pass, the factory ATTRACT MODE MESSAGE is restored. Next, the game adijustments are checked and restored to factory settings if an error is found. If game adjustments are found intact, the high score table is checked for any bad entries. Bad entries are replaced with a score of 4,000 points and no initials. If all entries check, the game returns to the Game Over Mode.

If game adjustments are restored fo factory settings, the AUDIT TOTALS are checked. If 5 or more audit digits are other than 0-9 (that is hexadecimal A through F) all audit totals are cleared. This is followed by a check of the high score table and the table is reset to factory settings if errors are found. Finally, game adjustments are rechecked and either OPEN COIN DOOR or FACTORY SETTINGS RESTORED is displayed. With the former, open the coin door and turn the game OFF and ON and then FACTORY SETTINGS RESTORED will be displayed. Return to game over by depressing the ADVANCE pushbutton or by turning the game OFF and ON a second time. RESTORE FacToRY MESSAGE

came ADJUSTMENTS PASS

RESTORE FACTORY SETTINGS,

RESET HIGH SCORE TABLE To FACTORY SETTINGS

‘OPEN COIN DOOR POWER OFF AND ON

0) NL

“OPEN COIN DOOR’ DISPLAYED Fait

BAD ENTRIES. REPLACED WITH 4,000 AND NC. INITIALS

“INITIAL TESTS INDICATE ALL SYSTEMS 50 DISPLAYED

"FICTORY SETTINGS RESTORED” DISPLAYED

Page 23

CHAPTER 4 Parts

Page 24

5678-09516-00—_ 4420-01 W090 CRE : 470i-00005-00. — 4320-01128-20-—— —

31~1045-3012-U

03-7696-1 S769 31+ 1076-3012-U SAK YY \. Sy Yes

Page 25

20-9267

01-7310

P/O 20-6542TB o1-65! 4608-01080-07, 01-7264,

P/0 20-654278 5640-06137

4320-01123-20 ‘01-7228

M694 l\-689-4- 01-7224 Ol- 6869 4700-00033-90. 5643-09556 4701 -00005-00. 20-9266 4420-O1117-00>

4608-01080-07 643-00268

Ol-6994- O|-5589

U-685-5- 03-7653 SN 5643-09268 =) Te | : 01-5589 / if I ol 1 i 1 r il i ft it AL] \ I ao ™ ee u Je

03-7602

Page 26

01-3827 wo so00-o1008-04

5792-09110-00 (8821-09081)

D-9157 LIGHT REFLECTOR ASSY. D-8374

‘SPEAKER PANEL ASSY

Page 27

§792-09094-00

§79'-O9111-00

01-6858 5014-09170-00 ‘ 5792-09865-00 |

20-9230-2

| 8792-09336-00 |—5792-09288-00

§792-09103-00 (CONN) 5822-09076 (PIN) '5792-09517-00 5823-09082 (KEY) D-8224-3006-

5792-09567-00

5731-06569-00

5731-09651-00 5731-06314-00 |-P/0 0-8784

5731-09432-00

5731-09432-00

D-8784,

P/O HI 8792-09698-00 (CONN) 5823-09360-00 (KEY) peaaeg——— 2 ( A2S

P/O C-8809 5700-09445-00 4008-01017-04

P/0 C-8809 5161-09552-00"

Page 28

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 29

ELECTRONICS, INC. 3401 N. California Ave., Chicago, IL 60618 (312) 267-2240, Telex 253095