Lazarian Parts and Operating Manual (Aug 1982)
Laser Battle (Zaccaria, 1981) · Parts & Operating Manual · 95 pages · 45 sections · original scan
August, 1982 Game Nos. 636, 641, 646
Bally/Midway’s
LICENSED FROM ZACCARIA
Parts & Operating Manual
NO. 641 MINI NO. 646 COCKTAIL
MIDWAY MFG. CO.
10750 W. Grand Avenue NS. 696 DERIGHT Franklin Park, Illinois 60131
U.S.A.
“Phone: (312) 451-1360 | Cable Address: MIDCO _— Telex No.: 72-1596
Form No. 0636-00300-0000
ELECTRICAL BULLETIN: FOR ALL APPARATUS COVERED BY THE CANADIAN STANDARDS ASSOCIATION (CSA) STANDARD C22.2 NO. 1, WHICH EMPLOYS A SUPPLY CORD TERMINATED WITH A POLARIZED 2-PRONG ATTACHMENT PLUG.
eepsen THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE
EX URE.
ATTENTION: POUR PREVENIR CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR. UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT.
C5%llly|MIDWAY
OUR TOLL FREE NUMBERS FOR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER BALLY/MIDWAY™ GAME YOU NOW HAVE ON LOCATION.
CALL US FOR PROMPT, COURTEOUS ANSWERS TO YOUR PROBLEMS
ANSWERS TO YOUR PROBLEMS.
Continental U.S. 800-323-7182 Illinois Only 1-800-942-0497
© COPYRIGHT MCMLXXXII BY BALLY/MIDWAY MFG. CO. ALL RIGHTS RESERVED. NO PART OF THIS PUBLICATION MAY BE REPRODUCED BY ANY MECHANICAL, PHOTOGRAPHIC, OR ELECTRONIC PROCESS, OR IN THE FORM OF A PHONOGRAPHIC RECORDING, NOR MAY IT BE TRANSMITTED, OR OTHERWISE COPIED FOR PUBLIC OR PRIVATE USE, WITHOUT PERMISSION FROM THE PUBLISHER. THIS MANUAL IS FOR SERVICE USE ONLY, AND NOT FOR GENERAL DISTRIBUTION. FOR PERMISSION REQUESTS, WRITE: MIDWAY MFG. CO., 10750 W. GRAND AVE., FRANKLIN PARK, IL 60131 Printed in U.S.A.
TABLE OF CONTENTS
DESCRIPTION PAGE
Introduction 2.6.0... ccc cece cece tenn ee eee eee n nents eee eee tet EEE EEE ee ee 1-1
Location and Setup Inspection .. installation . Game Volume Adjustment Control . Option Switch Settings ............
Game Operation Calibration Mode .. Attract Mode..... Ready to Play Mode Play Mode......... Two Player Operation 0.0.0.0... ccc cece eee ee eee 3,
Maintenance and Repair Cleaning . Fuse Replaceme: Opening the Control Panel .. Removal of the Main Display Glass & T.V. Bezel . T.V. Monitor Replacement ......... Printed Circuit Board Replacement. Opening the Attraction Panel
illustrated Parts Breakdown No. 636 — Lazarian Upright — Header Fluorescent Fixture Assy. ........... No. 636 — Lazarian Upright — Header Fluorescent Fixture Assy. — Parts List . No. 636 — Lazarian Upright — Front............ No. 636 — Lazarian Upright — Front — Parts List No. 636 — Lazarian Upright — Rear Access . No. 636 — Lazarian Upright — Rear Access — No. 641 — Lazarian Mini — Front........... No. 641 — Lazarian Mini — Front — Parts List. No. 641 — Lazarian Mini — Rear Access ........ No. 641 — Lazarian Mini — Rear Access — Parts List . No. 646 — Lazarian Cocktail — Front ............. No. 646 — Lazarian Cocktail — Front — Parts List . No. 646 — Lazarian Cocktail — Interior Access .. No. 646 — Lazarian Cocktail — Interior Access — Parts List. Lazarian Transformer Board Assy. — All Versions — Parts List. Knob Control — All Versions ..............+ Knob Control — All Versions — Parts List . Front Door Assy. — U.S.A, 25€.......... Front Door Assy. — U.S.A. 25¢ — Parts List ...
TABLE OF CONTENTS (cont'd)
DESCRIPTION PAGE
VI. Technical Troubleshooting. .......... 6... e eee e cee ene e eee e enn tenn ee eee te nen eee nn ees 6-1 Introduction ........ 6-1 General Suggestions 6-1 Harness Component Troubleshooting .. 6-1 Transformer and Line Voltage Problems 6-2 A Glossary of Microprocessor Terms . 6-3 Introduction to the Z80 CPU...... 6-3 General Purpose Registers . 6-4 Arithmetic and Logic Unit (ALU)... 6-4 Introduction Register and CPU Control. 6-4 Z80 CPU Pin Description - 6-4
VE. Coin Door Maintenance .......... 2... cece ene eee n ene een eect ence ne teen tenn ene enn ees 7-1 Metal Coin Acceptor Merchanisms ... wT Plastic Coin Acceptor Mechanisms... 27-8
VII. T.V. Monitor Manual 8-1 Introduction ...... 8-1 Symptom Diagnosis .. 8-2 Guide to Schematic Symbols . 8-3 Troubleshooting 8-5 Theory of Operation. . 8-6
IX. | Schematics & Wiring Diagrams
1.C. Functions Wiring Diagram — Upright Wiring Diagram — Mini... Wiring Diagram — Cocktai Power Supply P.C.B. — Component Layout Power Supply P.C.B. — Schematic . Game Board — Component Layout Game Board — Schematic......... Sound Board — Component Layout Sound Board — Schematic .......... Monitor Interface P.C.B. — Component Layout Monitor Interface P.C.B. — Schematic Diode P.C.B. — Component Layout Diode P.C.B. — Schematic ©CEEYLODOOO NOdkRON= oo a4 a0
TABLE OF FIGURES
FIGURE PAGE
1-1 Assigned Point Values..............c cece ccc cece cece ee eeeesuueaseeeeutetteeeeteeeeee 1-2 2-1 Location of Serial No., Interlock Switch, On/Off Switch, & Major Sub-Assemblies . 2-2 2-2 Major Sub-Assemblies (Cont. from Fig. 2-1) an 12-3 2-3 Interlock Switch Operation ........ 12-3 2-4 Game Volume Adjustment Control . 12-4 2-5 Option Switch Locations 12-4 2-6 Option Switch Settings . 12-5 4-1 Location of Fuses.... ws 4-1 4-2 Opening the Control Panel — Upright & Mini. 14-2 4-3. Opening the Cocktail Game ............. 4-3 4-4 Removing the Control Panel — Cocktail.... 4-3 4-5 Removing the Main Display Glass & T.V. Bezel — Upright . 4-4 4-6 Removing the Main Display Glass & T.V. Bezel — Mini 4-4 4-7 Removing the Top Glass — Cocktail . 4-5 4-8 Removing the Monitor — Upright 4-6 4-9 Removing the Monitor — Mini 4-6 4-10 Opening the Cocktail Game .. 4-7 4-11 Removing the Monitor — Cocktail 4-7 4-12 Replacing P.C.B.s — Upright 4-8 4-13 Replacing P.C.B.s — Mini. 4-8 4-14 Replacing P.C.B.s — Cockta' 4-9 4-15 Opening the Attraction Panel prig| .4-10 4-16 Replacing Fluorescent Tube Starter .. 14-11 4-17 Opening the Attraction Panel — Mini..... 4-11 7-1 Removing and Replacing the Coin Acceptor 7-1 7-2 Cleaning the Metal Coin Acceptor .. 7-2 7-3 Lubricating the Metal Coin Acceptor 7-2 7-4 Opening the Plastic Coin Acceptor.. ae 7-3 7-5 Changing the Plastic Coin Acceptor to Accept American or Canadian Quarters .. 27-4
iii
Lazarian
IMPORTANT NOTE
DO NOT plug in your new game yet. Before you do anything to your game, we recommend that you read SECTIONS | and || of this manual completely. It will not take more than a few minutes and it may be very helpful.
I. Introduction
LAZARIAN is a one or a two player game. There are three models: the “UPRIGHT”, “MINI”, and “COCK- TAIL TABLE”. When the two player mode is selected on the Upright or Mini model, the players take turns at the controls to fly their space fighter(s) through the game course. If you have purchased the Cocktail Table model of this game, the rules of play are the same. The only difference is that in the two player mode of the Cocktail Table game, the picture flips to face you when it’s your turn.
When playing this game, you are the pilot of a space fighter stationed in various places to rescue one of your stranded ships and to defend your sector of space against any and all types of hazards.
In the first phase of the first mission of game play, one of your sister ships is in trouble and sending out an SOS. It is completely surrounded by meteors which are held in a tight circle around it by separate interlocking force fields. Your task is to shoot the force fields as they turn yellow which causes them to release that particular meteor. You must release ALL the meteors BEFORE you will be able to rescue your sister ship. After rescuing your sister ship, you must then avoid the meteorites coming at you and destroy all the
1-1 meteors circling around you BEFORE your fuel runs out. This will enable you to advance to the next phase of the first mission. {f you accomplished all of the above, your space ship is refueled and you are sent out on the second phase of your first mission — to rescue another ship which is in distress at the top left corner of your monitor's screen. To do this, you must face and surmount severl different kinds of deadly obstacles while working your way through the four different levels of the tunnel. Again, you must do this BEFORE your fuel runs out. When you have completed this latest rescue mission, your ship is refueled once more and you must face the one-eyed space leviathan in the third phase of your first mission. The only way to destroy it is by shooting its eye. This is not easy, to say the least. And again, you MUST do this BEFORE your fuel is exhausted. As your skill level increases, and you advance farther and farther into the game, each successive mission becomes harder and harder to complete. A bonus ship (this is switch selectable) may be awarded to you as you reach or pass a certain preselected point value. Each item which can be shot has an assigned point value as listed in Figure 1-1.
Major New Features
One new feature of your LAZARIAN game is the ability of your space ship to fire to the left, right, up, or down, giving you greatly increased fire power. Another new feature of your LAZARIAN game which will increase your ship's fire power to an even greater degree is the addition of optional switch selectable Laser Fire: Normal Manual Laser Fire (Laser fires as fast as you can press the FIRE buttons), and Automatic Rapid Laser Fire (Laser fires at a high rate foras long as any of the FIRE buttons are held down).
Game Objective
The object of the game is to HAVE FUN and survive as long as possible while constantly improving your skills and destroying as many of the enemy as you can. As you do this, each successive mission will be harder to complete.
SCORING TABLE
FIRST PHASE OF EACH MISSION
OBJECT
LIBERATED METEOR DESTROYED METEOR POINT VALUE
VARIABLE — 10 TO 100 POINTS EACH VARIABLE — 10 TO 100 POINTS EACH
SECOND PHASE OF EACH MISSION =
OBJECT
ALIENS IN FIRST TUNNEL LEVEL FORTS IN SECOND TUNNEL LEVEL ALIENS IN THIRD TUNNEL LEVEL DISTRESSED SISTER SHIP RESCUED
THIRD PHASE OF EACH MISSION
OBJECT
PIECES OF LEVIATHAN ALIENS IN THIS RACK LEVIATHAN’S EYE RELEASED 1ST, 2ND, & 3RD LASER HITS ON EYE 4TH LASER HIT ON EYE (DESTROYS IT) POINT VALUE
70 POINTS EACH 70 POINTS EACH 70 POINTS EACH 1000 POINTS
POINT VALUE
5 POINTS EACH 70 POINTS EACH 1000 POINTS 500 POINTS EACH 1000 POINTS
Figure 1-1 Assigned Point Values
1-2
II. Location and Setup
INSPECTION 1. 2. Remove the game from its shipping crate. Inspect the entire outside of it for any signs of damage. O Any scratches?, dents?, cracks? O Any broken controls? C Any broken glass or plastic? O Just look it over closely and make a note of any” signs of damage. . Remove the shipping cleats from the bottom of the cabinet. O UPRIGHT MODELS ONLY: In order to help prevent easy theft of your game, you may wish to remove the Caster Wheel Assemblies from the bottom of your cabinet at this time. . Install the four levelers, one at each corner of the cabinet. C Level the cabinet. . Open the cabinet and inspect the inside of the game for any signs of damage. See Figure 2-1. 0 Also check to make sure all plug-in connectors on the wire harness are firmly seated.
Replug any connectors found unplugged. DO NOT FORCE PLUGS ONTO CONNECTORS. DO NOT FORCE PLUGS TOGETHER. If it won't go on easily, assuming the keys are lined up, it either does not belong there or is damaged. O Make sure all printed circuit boards (P.C.B.’s) are firmly seated in their connectors. See Figure 2-1. These connectors are also keyed. The P.C.B.’s will only go into them one way without being damaged. 0 Note the location of the game's serial number. See Figure 2-1. O Check all major subassemblies to be sure they are mounted securely. These are cailed out in Figures 2-1 & 2-2. Power supply. Control panel(s). T.V. monitor. Other P.C.B.’s and/or P.C.B. rack, etc. Power supply filter assembly. Transformer board assembly. . Make a note of any problems that can’t be easily corrected. . Call your distributor and/or service man about your problem list.
2-1 INSTALLATION
- Location requirements: D Power: Domestic 110 V @ 60 Hz Foreign 200 V to 240 V @ 50 Hz O Temperature: 32° to 100°F (0° to 38°C) O Humidity: Not over 95% relative O Space required: Upright 29” x 25" (73cm x 63cm) Mini 20” x 24” (50cm x 60cm) Cocktail 32” x 22" (81cm x 55cm) O Game height: Upright 68" (170cm) Mini 61" (153cm) Cocktail 29” ( 73cm) . Voltage Selection: Your game is designed to work properly on the line voltage where you are located. Check your line voltage with a meter to determine what its value is. Then check the power input wires to the main power supply transformer on your game to be sure they are connected to taps which correspond to your line voltage value. If the power input wires to the main power supply transformer are not connected to taps which correspond to your local line voltage, move them to the proper taps. If the line voltage in your area falls outside the upper or lower limits of the range of inputs covered by the main power supply transformer, DO NOT PLUG YOUR GAME IN until you have talked with your distributor and/or service man and obtaineda solution to this problem. Otherwise you could damage your game. . Interlock and power ON/OFF switches. See Figure 2-1. O To help prevent the possibility of getting an electric shock while working inside the game cabinet, interlock switches have been installed at each cabinet access door (this DOES NOT include the coin door in the Upright and Mini models). O When any access door is opened, the interlock switch installed there turns off all power to the game. O Check each operation. After checking the line voltage in your area and determining that the input wires to the main power supply transformer of your game are connected properly — or — after obtaining a solution to your over or under voltage problem from your distributor and/or your service man, plug the game into your A.C. wall outlet. interlock switch for proper
ON/OFF SWITCH
INTERLOCK SWITCH
TRANSFORMER BOARD ASSY. (NOT SEEN)
UPRIGHT
SERIAL NUMBER (MAY BE LOCATED ON ANY CORNER)
TRANSFORMER BOARD ASSY.
CONTROL
GAME BOARD
INTERLOCK SWITCH (INSIDE DOOR) ~~ SERIAL NUMBER
TV. MONITOR
COCKTAIL INTERLOCK SWITCH
SWITCH
TRANSFORMER BOARD ASSY. (NOT SEEN)
TV. MONITOR
POWER SUPPLY P.C.B.
CONTROL PANEL (PLAYER 2)
ON/OFF SWITCH UNDER GAME ON PLAYER 2 SIDE
Figure 2-1 Location of Serial No., Interlock Switch, On/Off Switch & Major Sub-Assys.
CONTROL
UPRIGHT
Figure 2-2 Major Sub-Assys. (cont. from Fig. 2-1)
The game ON/OFF switches for all models are located as shown in Figure 2-1. Turn the game on and allow it to warm up a few minutes. Slowly open each access door to the game (this does not include the coin door on the Upright and Mini models). As the door is opened approximately 1” (2.54cm) the power to the game should go off (the T.V. monitor, all the lights, and all sounds will stop). If this does not happen, check the interlock switch by this door to see if it has broken loose from its mounting or if it is stuck in the “ON” position. If the switch is found to be bad, turn the game off, unplug it, and replace the interlock switch. When done, plug the game back into the wall outlet, close the access door, and turn the game back on. After the game has warmed up, repeat the above interlock switch test. When the interlock switch is working properly and turns the power to the game off, power may be restored to the game with the access door(s) open. Take hold of the interlock switch plunger and gently pull it out to its fully extended position. THIS IS TO BE USED ONLY FOR SERVICING THE GAME. See Figure 2-3.
“sn . ’
Figure 2-3 Interlock Switch Operation
GAME VOLUME ADJUSTMENT CONTROL. See Figure 2-4. The volume control pot is located on the Sound board. This is a somewhat smaller P.C. Board than the main game P.C. Board. It may be reached through the coin door on the UPRIGHT models and through the rear access door on the MINI models. On the COCK- TAIL TABLE models, you will have to open the table top to reach it.
To make the sounds louder, turn the pot clockwise as you face it (7% ). To make the sounds less loud, turn the pot counterclockwise as you face it (~~ \).
GAME VOLUME CONTROL (ON SOUND BOARD)
Figure 2-4 Game Volume Adjustment Control OPTION SWITCH SETTINGS To change the option switch settings, you DO NOT have to take the CPU board out of the game. They can be easily reached through the rear access door on the Upright and Mini models. On the Cocktail Table model, you do have to open the table top to reach them. When changing any options, ALWAYS check the results by playing the game to be sure the switches have worked properly and that no switches were accidentally moved that were not meantto be. (These switches are small and this can happen.) The option switch settings and what they will make the game do are shown in Figure 2-6. See Figure 2-5 for option switch locations.
OPTION SWITCHES
Figure 2-5 Option Switch Locations
2-4
LAZARIAN
OPTION SWITCH SETTINGS
SW#1 SW#2 SW#3 SWH4 SWHS SWHE SWH7 SWH8 COINS PER PLAY 2 COINS 1 PLAY *1 COIN 1 PLAY 1 COIN 2 PLAYS 1 COIN 3 PLAYS
NUMBER OF SHIPS PER PLAY 2 SHIPS *3 SHIPS 4 SHIPS 5 SHIPS
*CALIBRATION GRID NOT DISPLAYED CALIBRATION GRID DISPLAYED
“TEST” COLLISION DETECTION DISABLE *“GAME” COLLISION DETECTION NORMA\
LASER FIRING CONTROL NORMAL FIRE *RAPID FIRE
MONITOR CONTROL
- NORMAL OPERATION FREEZE THE PICTURE
DIFFICULTY LEVEL EASY GAME *MEDIUM GAME DIFFICULT GAME VERY DIFFICULT GAME
BONUS SHIPS AWARDED AT: NO BONUS SHIP AWARDED 10,000 POINTS — ONE SHIP ONLY *14,000 POINTS — ONE SHIP ONLY 18,000 POINTS — ONE SHIP ONLY
*INDICATES FACTORY RECOMMENDED SETTINGS. ON NOT NOT ON USED USED ON OFF ON OFF
SW#1 SW#2 SW#3 SW#4 SWHS SWH6 SWH7 SWHE ON ON OFF ON ON OFF ON OFF
SW#1 SW#2 SW#3 SW#H4 SWHS SWHE SW#7 SWHB
SWiH1 SW#2 SW#3 SW#4 SW#5 SWHE SWH7 SWHB ON ON OFF ON ‘ON OFF OFF OFF
SWi1 SW#2 SW#3 SW#4 SW#S SWH6 SWH7 SWHB ON ON OFF ON ON OFF OFF OFF
PART NO. M051-00636-A011
Figure 2-6 Option Switch Settings
Ill. Game Operation
LAZARIAN is a one or a two player game with acolor T.V. monitor. The game has five possible modes of operation: ATTRACT, READY-TO-PLAY, PLAY, HIGH SCORE/ INITIAL, and SELF-TEST.
CALIBRATION MODE To put the game into its CALIBRATION MODE the game MUST be “ON”. Then slide SW#7 of SWITCH PACK SW-1 to the “OFF” position (on UPRIGHT and MINI models, this Switch can be reached through the rear access doors — on COCKTAIL TABLE models, you will have to open the table top to reach it). At this time the game will display a GRID PATTERN on the monitor screen. This may be used for making any one of the number of adjustments to the game. This GRID PATTERN will remain on the monitor screen until the above SW#7 of SWITCH PACK SW-1 is returned to the “ON” position.
ATTRACT MODE
- The Attract mode starts:
D Just after power has been turned on to the game. O After a play has been finished, the score was not high enough to put the game into the High Score/Initial mode, and there are no more credits left in the game’s memory. O After the High Score/Initial mode when there are no more credits left in its memory.
The next display in the series lists the five highest scoring individuals that have played the game to date.
LTT) 05790 00000 gh Score Play
TODAYS HIGH SCORES
LUU DAV SIL SAW YER 00000 00000 00000 00000 00000
MOVE CONTROL LEVER LEFT OR RIGHT TO SELECT LETTERS. PRESS FIRE BUTTON TO INSERT LETTERS
CREDIT 00 When a game(s) has been paid for, the only difference in the game display is that the first display of the Attract Mode changes to that shown below:
PUSH START BUTTON
- MIDWAY MFG. CO. 1981 ZACCARIA
READY-TO-PLAY MODE
- The Ready-To-Play mode starts when enough coins have been accepted for a 1 or a 2 player game. . The Ready-To-Play mode ends when either the “1 PLAYER” or the “2 PLAYER” push button is pressed. . In the Ready-To-Play mode, the game will give the above display in place of the first display of the Attract mode.
. lf no START button is pressed, the game will continue to run its Attract mode sequence of displays with the modified first display as shown above.
PLAY MODE
- The Play mode begins when either the “1 PLAYER” or the “2 PLAYER” start button is pressed. The Play mode ends when all of your space ships have been destroyed. When this happens, “GAME OVER” is written across the center of the monitor screen. . The game is made up of individual missions with three repeating phases each: two distressed space ships which it is your task to rescue (each rescue being more difficult than the one before) and a space leviathan (monster) which you must destroy. This sequence repeats throughout the 2.
game. However, each time you go through it, it will be more difficult to complete than the last time you went through it. The increased level of difficulty is accomplished by such means as shortening the range of your lazer and speeding up the timing of events within each phase of a mission. For instance, the period of time that any force field will stay yellow in the first phase of a mission is shortened. After you complete each phase of the mission, your space ship moves to the point on the screen where it has to be to begin the next phase of the mission. . In the first phase of the first mission of game play, one of your sister ships is in trouble and sending out an SOS. It is completely surrounded by meteors which are held ina tight circle around it by separate interlocking force fields. Your task is to shoot the force fields as they turn yellow which causes them to release that particular meteor. You must release ALL the meteors BEFORE you will be able to rescue your sister ship. When the last meteor is released, your space ship is given another full load of fuel for completion of the rescue. After rescuing your sister ship, you must then avoid the meteorites coming at you and destroy all the meteors circling around you BEFORE your fuel runs out. This will enable you to advance to the next phase of the first mission. If you accomplished all of the above, your space ship is refueled and you are sent out on the second phase of your first mission — to rescue another ship which is in distress at the top left corner of your monitor's screen. To do this, you must face and surmount several different kinds of deadly obstacles while working your way through the four different levels of the tunnel. Again, you must do this BEFORE your fuel runs out. When you have completed this latest rescue mission, your ship is refueled once more and you must face the one-eyed space leviathan in the third phase of your first mission. The only way to destroy it is by shooting its eye. This is not easy, to say the least. Because when your lazer first touches the leviathan’s eye, it escapes from the dying monster. The escaped eye then moves about the monitor's screen in varying patterns and must be hit four times by your lazer before it will explode and die. Your space ship is also NOT given another full load of fuel upon the escape of the eye from the dying leviathan so you have LESS fuel tocomplete the mission and kill the eye. And again, you MUST do this BEFORE your fuel is completely exhausted in order to be able to advance to the next mission. After completing the third phase of any mission — destroying the leviathan’s eye, the screen is cleared, “GO FOR NEXT MISSION” is displayed
3-2 centered on monitor screen, the screen is then cleared again. As your skill level increases, and you advance farther and farther into the game, each successive mission becomes harder and harder to complete.
When your last space ship is destroyed, the words “GAME OVER” are displayed centered on the monitor screen. (AT THIS POINT, SEVERAL DIF- FERENT THINGS CAN HAPPEN DEPENDING ON WHAT YOUR SCORE WAS AND WHETHER OR NOT THERE ARE CREDITS STILL REMAIN- (NG IN THE GAME’S MEMORY.) If you are still in the 1st MISSION when your last space ship was destroyed, the game will give you the opportunity to continue the game from the point where you lost this last space ship by displaying the following message on the screen.
PLAYER MAY CONTINUE GAME BY INSERTING COIN WITHIN 10 SECONDS
This option is not offered by the game if your last space ship is lost in any MISSION beyond the ‘st. If you lose your last space ship in a MISSION beyond the 1st, you must start your next game at the beginning of the 1st MISSION again. lf your score was high enough to be one of the five best scores, the game will go into the High Score/Initial mode immediately. If your score is not high enough to cause the game to go into the High Score/Initial mode, it will either go to the Attract mode (if there are no more credits left in its memory) or into the Ready-To-Play mode (if there are still credits left in its memory).
HIGH SCORE/INITIAL MODE: In the High Score/Initial mode the game gives a display which looks like the following:
03540 [FUELTT TT TTT 05790 00000 Player 1 H
TODAYS HIGH SCORES
LUU 00000 DAV 00000 SIL 90000 SAW 00000 YER 00000
MOVE CONTROL LEVER LEFT OR RIGHT TO SELECT LETTERS. PRESS FIRE BUTTON TO INSERT LETTERS
CREDIT 00
When in the High Score/Initial mode, YOUR SCORE has been positioned in its proper order among the other four high scores. The space at the left of your score is where you enter your initials. There will be an “A” in the first space and the other two spaces will be blank. By moving the controller stick to the right, the letter can be made to sequence forward through the alphabet: “A”, “B”, “C”, “D”, etc. By moving the controller stick to the left, the letter can be made to sequence backward through the alphabet: “2”, “yn”, “W", ete. When you reach your initial, release the controller and push any of the FIRE buttons. Your first initial is frozen in place and an “A” now appears in what was the blank space to the right of your first initial. You enter your second (and third) initial in the same manner as you did your first initial. If you do not wish to put your initials opposite your score, just press any of the FIRE buttons three times. Three “A”’s will appear opposite your score. After the High Score/Initial mode, the game will either go to the Attract mode (if there are no more credits left in its memory) or into the Ready-To- Play mode (if there are still credits left in its memory). Most of the above holds true in the “2 PLAYER” mode also. But there are a few minor differences. TWO PLAYER OPERATION The Upright, Mini, and Cocktail Table models all have two player operation. In the two player mode, the rules of play are the same as in the single player mode. There are some additional rules however.
- In the Upright and Mini models, the players must take turns at the controls.
- In the Cocktail Table model, each player has his own set of individual controls. The picture will flip to face you when it is your turn. (When itis not your turn, your set of controls will have NO effect on the game.)
- Your turn lasts until your space ship is destroyed. At this point, the game will do one of several things depending on whether or not the destroyed ship was your last or if you still have others remaining in reserve.
SPACE SHIP DESTROYED — OTHERS REMAIN- ING IN RESERVE
O All movement stops. O Next, the screen is cleared and the following display shown centered on the monitor screen:
00120 (Fur C 05790 05210 Player 1 Score Player 2
PLAYER ONE
START MISSION \
OR PLAYER TWO
O The screen is cleared again and play begins for the other player.
SPACE SHIP DESTROYED — NONE REMAINING IN RESERVE
O All movement stops and screen is cleared. DO Game displays “GAME OVER”. O Next, if your score was high enough to be one of the five best scores, the game will go into the High Score/Initial mode presentation immediately. O After you have entered your initials, the screen is cleared and the following display shown centered on the monitor screen:
TTTITI 05790
PLAYER ONE
START MISSION
OR PLAYER TWO
O The screen is cleared again and play begins for the other player. D If your score was not high enough to cause the game to go into the High Score/Initial mode, it will go right to the above display, the screen will be cleared, and play will begin for the other player.
IV. Maintenance and Repair
Your NEW game needs certain types of maintenance to keep it in good working order. CLEAN, well MAINTAINED games attract players and EARN MORE PROFITS. The most important thing for you to remember is to play your game thoroughly EVERY TIME you collect money from the coin box. JUST LOOKING at your game WILL NOT tell you if all its controls and inside parts are working correctly. ONLY being familiar with and playing your game will inform you whether or not it is working the way it should. The second most important thing you should remember is to clean the outside of the game and coin acceptor mechanisms on a regular basis.
CLEANING The outside of the game cabinet plus the metal can be cleaned with any non-abrasive household cleaner. However, the front of the T.V. monitor tube and both sides of all other glass and plastic on or in the game MUST be cleaned with anti-static cleaner ONLY. For cleaning the coin acceptors: hot soapy water may be used on the plastic ones and any household cleanser may be used on the metal ones. If you wish, special coin machine cleaners that leave no residue may be purchased from your distributor. DO NOT dry-wipe any of the plastic panels. This is . because any dust that was on them can scratch their surfaces. If this has happened, anyone looking through this type of damaged plastic would feel he was looking at the game through a fog. This fogging damage CANNOT be repaired or reversed. The ONLY solution is to replace the damaged piece of plastic. FUSE REPLACEMENT This game contains several fuses located as shown in Figure 4-1. 1, UPRIGHT MODEL: As viewed from the back, facing the cabinet, with the rear access door removed; the fuses are located on the Transformer and the Power Supply Board Assemblies.
- MINI MODEL: As viewed from the back, facing the cabinet, with the rear access door removed; the fuses are located on the Transformer and the Power Supply Board Assemblies.
- COCKTAIL TABLE MODEL: As viewed from the coin door side of the cabinet, with the monitor tilted open to one side; the fuses are located on the Transformer and Power Supply Board Assemblies. Replace fuses ONLY with the type and size listed in the Illustrated Parts Breakdown Section of this manual. See the T.V. Monitor Manual (available on request from your Distributor or the Monitor manufacturer) and/or the T.V. Troubleshooting Section of this manual for information on these fuses.
FUSES ON TRANSFORMER BOARD & POWER SUPPLY PCB (TYP. ALL 3 MODELS)
Figure 4-1 Location of Fuses
OPENING THE CONTROL PANEL. See Figure 4-2.
- UPRIGHT MODEL: . 2. MINI MODEL: O The control panel is held in place by three latches, one on the left side, one on the right side, and one on the front center. They are spring loaded to provide constant positive pressure on their latch plates. They can be reached through the coin door AFTER turning power to the game off. To release the latches, lift up and toward the front center of the control panel. Once they are released, unhook them from their latch plates. To remove the control panel: Raise it up and tilt it toward you until you can see the cable behind it. Cradling the control panel between yourself and the cabinet, disconnect it from its cabling. The contro! panel is now free and can be removed. O To reinstall the contro! panel, reverse this procedure.
UPRIGHT O The control panel is held in place by two latches, one on the right side ana one on the left side of the cabinet. They are spring loaded to provide constant positive pressure on their latch plates. They can be reached through the coin door AFTER turning power to the game off. To release the latches, lift up and toward the center of the control panel. Once they are released, unhook them from their latch plates. 0 To remove the control panel: Raise it up and tilt it toward you until you can see the cable behind it. Cradling the control panel between yourself and the cabinet, disconnect it from its cabling. The control panel is now free and can be removed. 0 To reinstall the control panel, reverse this procedure.
Figure 4-2 Opening the Control Panel — Upright & Mini
Figure 4-3 Opening the Cocktail Game
- COCKTAIL TABLE MODEL:
O Each control panel is held in place by several screws, two on the inside of the cabinet and three along the outside bottom edge of the control panel. Turn power to the game off. Open the coin box door and release the two latches indicated in Figure 4-3. is very close to monitor. the HIGH VOLTAGE on
Once they’re released, unhook them from their latch plates. Grasp the table top at “A” and: open it as indicated in Figure 4-3.
Remove the screws which secure the control panel in place. See Figure 4-4. O To remove the contro! panel(s): Disconnect it from its cabling. The control panel is now free and can be removed. Q To reinstall the control panel, reverse this procedure. LIFT CONTROL UP
REMOVE
- SCREWS , EACH SIDE
REMOVE(3) SCREWS
LJ]
Figure 4-4 Removing the Control Panel — Cocktail
REMOVAL OF THE MAIN-DISPLAY- GLASS AND/OR THE TV. BEZEL ASSEMBLY 1. UPRIGHT MODEL: See Figure 4-5.
O By putting your finger in the hole in the middle of the main-display-glass support, you can lift it up and out.
O Loosen the screws which secure the T.V. bezelglass-clamps in place. Move the clamps to the side and the bezel glass may be removed. Remove the above mentioned screws and the bezel with four bezel-glass-clamps may be removed.
O To reinstall the T.V. bezel assembly and the main-display-glass, reverse this procedure.
DISPLAY GLASS
GLASS CLAMPS
Figure 4-5 Removing Main Display Glass & T.V. Bezel
- Upright
4-4
- MINI MODEL:
O Remove the screws which secure the T.V. bezel assembly and lift it out.
DISPLAY GLASS
GLASS CLAMPING PLATE
Figure 4-6 Removing Main Display Glass & T.V. Bezel
- Mini
. COCKTAIL TABLE MODEL: See Figure 4-7.
Figure 4-7 Removing Top Glass & T.V. Bezel
- Cocktail
4-5 T.V. MONITOR REPLACEMENT
1, UPRIGHT MODEL: See Figure 4-8. O Turn power off to the game. O Open the rear access door. O Completely disconnect the T.V. monitor from all its cabling. DON'T FORGET THE CHASSIS GROUND WIRE. Before removing the T.V. monitor, the maindisplay-glass and bezel MUST be removed. See above “Upright Model” procedure. With the removal of only four bolts, the T.V. monitor and its mounting channels will be loose. The monitor mounting channels slide on top of and against two metal guides mounted to the cabinet's right and left sides. The monitor is removed by sliding it out the back of the cabinet. See Figure 4-8. O To reinstall the T.V. monitor, reverse this procedure. O After replacing the T.V. monitor, be sure to run the game Self-Test. MINI MODEL: See Figure 4-9. O Turn the power off to the game. O Open the rear access door. O Completely disconnect the T.V. monitor from all its cabling. DON'T FORGET THE CHASSIS GROUND WIRE. Before removing the T.V. monitor, the maindisplay-glass and bezel MUST be removed. See above “Mini Model” procedure. With the removal of only four bolts, the T.V. monitor will be loose.
The monitor is removed by supporting it and pulling straight back as shown in Figure 4-9, O To reinstall the T.V. monitor, reverse this
procedure. Q Once the latches are released, unhook them
After replacing the T.V. monitor, be sure to run from their latch plates. the game Self-Test. Q Grasp the table top at “A” and open it as indicated in Figure 4-10.
- COCKTAIL TABLE MODEL: See Figure 4-11.
REMOVE REMOVE (4)
- BOLTS
Figure 4-8 Removing Monitor — Upright Figure 4-9 Removing Monitor — Mini
4-6
CLAMPS
Figure 4-10 Opening the Cocktail Game
O Remove the screws which hold the table top glass clamps in place. O Remove the table top glass. C Lift out the T.V. bezel assembly. O Completely disconnect the T.V. monitor from all its cabling. DON'T FORGET THE CHASSIS GROUND WIRE. O Remove the screws holding the T.V. monitor chassis to the “L” by the door hinge(s). See Figure 4-11. O Close the Cocktail Table and re-latch it.
C1 Remove the screws which secure the T.V monitor mounting brackets to the edges of the slot cut in the table top. See Figure 4-11. O Pry up the end of each monitor mounting bracket with a screwdriver or similar tool until you can grasp them both. O Lift the T.V. monitor straight up and out of the table top being VERY CAREFUL not to bump the neck of the picture tube. O To reinstall the T.V. monitor assembly, reverse this procedure. O Be sure to check the clearance of the “L” brackets BEFORE setting the monitor into the table top. O After replacing the T.V. monitor, be sure to run the game Self-Test. REMOVE 6 SCREWS (3 EACH SIDE) LIFT MONITOR
STRAIGHT UP
REMOVE 4 SCREWS (2 EACH SIDE)
Figure 4-11 Removing Monitor — Cocktail
PRINTED CIRCUIT BOARD (P.C.B.) REPLACEMENT
- UPRIGHT MODEL: See Figure 4-12. C Turn the power to the game off.
O Unlock and open the rear access door (game board) and the coin door (sound board). 0 Disconnect the game board from all its cabling. 0 Disconnect the sound board from all its cabling. O Remove the indicated P.C.B. supports and lift the above P.C.B.’s out the cabinet.
REMOVE
REMOVE SUPPORT TO SLIDE GAME BOARD SLIDE POWER SUPPLY BOARD OUT OUT
Figure 4-12 Removing P.C.B.s — Upright 0 Disconnect the power supply board from all its cabling, remove the P.C.B. supports indicated in Figure 4-12, and slide it out the back of the cabinet.
O To reinstall the above P.C.B.’s, reverse this procedure.
UNSCREW BOARDS FROM CABINET TO REMOVE
REMOVE SUPPORT TO SLIDE GAME BOARD FROM CABINET REMOVE SUPPORT TO SLIDE POWER SUPPLY BOARD FROM CABINET
Figure 4-13 Removing P.C.B.s — Mini
REMOVE SUPPORT TO SLIDE GAME BOARD OUT
UNSCREW BOARDS TO REMOVE FROM CABINET REMOVE SUPPORT TO SLIDE POWER SUPPLY BOARD FROM CABINET
Figure 4-14 Removing P.C.B.s — Cocktail
- MINI MODEL: See Figure 4-13. O Turn the power off to the game.
O Unlock and open the rear access door. O Disconnect the game board from all its cabling. Disconnect the sound board from all its cabling. O Remove the indicated P.C.B. supports and lift the above P.C.B.’s out of the cabinet. O Disconnect the power supply board from its cabling, remove the P.C.B. supports indicated in Figure 4-13, and slide it out the back of the cabinet. . O To reinstall the above P.C.B.’s, reverse this procedure.
- COCKTAIL TABLE MODEL: See Figure 4-14. O Turn the power off to the game. O Open the cabinet: Open the coin box door and release the two latches indicated in Figure 4-10.
Once they're released, unhook them from their latch plates.
4-9 O Grasp the table top at “A” and open it as indicated in Figure 4-10.
To remove the power supply board. See Figure 4-14. Disconnect it from all its cabling. Remove the two smallest P.C.B. supports. Once these are removed, the power supply can be lifted out the top of the cabinet. To reinstall the power supply board, reverse this procedure.
To remove the game and Sound boards. See Figure 4-14. Disconnect the game board from all its cabling. Disconnect the sound board from all its cabling.
O Remove the indicated P.C.B. supports and lift the above P.C.B.'s out of the cabinet. To reinstall the game and sound boards, reverse this procedure.
OPENING THE ATTRACTION PANEL:
- UPRIGHT MODEL: See Figure 4-15. C Turn the power to the game off. O Opening the attraction panel: Remove the screws which secure the top bracket in place. (They are on its top side.) See Figure 4-15. Remove the top bracket and slide up the attraction panel. This exposes the attraction panel fluorescent light tube and its mounting bracket assembly. To reinstall the attraction panel, reverse this procedure. O The fluorescent light tube may be replaced at this time. BE CAREFUL NOT TO DROP IT.
D Replacing the fluorescent light tube starter. See Figure 4-16. Be sure the power to the game has been turned off. Grasp the starter (it is on the back of the mounting bracket), give it a quarter turn, and remove it from its socket. To replace the fluorescent light tube starter, reverse this procedure. O Replacement of the fluorescent tube mounting bracket assembly. Be sure the power is off to the game. Disconnect it from its power cable. Remove the screws which secure it and gently slide it out the front of the cabinet, being careful not to catch its power cable on anything. To reinstall the fluorescent tube mounting bracket assembly, reverse this procedure. O Replacing the speaker. Be sure the power is off to the game. Remove the attraction panel and disconnect the speaker from its cabling. Remove the nuts and bolts which secure the speaker and speaker grill in place and set them and the speaker grill aside. Once the bolts which secure the speaker in place are removed, the speaker may be removed through the opening where the attraction panel was. Reverse this procedure to reinstall the speaker. REMOVE TOP BRKT. & SLIDE HEADER UP
Figure 4-15 Opening the Attraction Panel — Upright
- MINI MODEL: See Figure 4-17. O Turn the power off to the game. U Remove the screws from the top and bottom of the formed attraction panel. O Remove the formed attraction panel by pulling it straight away from the cabinet. This exposes the attraction panel light bulbs and their mounting board.
r™ Y%, TURN FLUORESCENT TO REPLACE TUBE STARTER
Figure 4-16 Replacing Fluorescent Tube Starter
O To service the light bulbs and their mounting REMOVE TOP
board: BRKT. & SLIDE
Turn the power to the game back on so you can HEADER UP see which bulbs are burnt out. Mark the burnt out bulbs and turn the power to the game back off again. To replace the burnt out bulbs, grasp them gently and pull straight out. The new bulbs are gently pushed into the empty sockets. To completely replace the light bulb mounting board: Open the cabinet rear access door and unplug the mounting board from its power cable. Remove the screws that hold the mounting board to the cabinet. Gently slide the mounting board out the front of the cabinet being careful not to catch its cable on anything. To reinstall the above removed items, reverse this procedure. O To replace the speaker. Be sure the power is off to the game. Disconnect the speaker from its cabling. Remove the nuts and bolts securing the speaker. Slide the speaker out through the rear access door. To reinstall the speaker, simply reverse this procedure.
- THE COCKTAIL MODE HAS NO BACK-LIT AT- TRACTION PANEL. Figure 4-17 Opening the Attraction Panel — Mini
4-11

This page is a drawing, shown as the original scan.
NO. 636 — LAZARIAN UPRIGHT — HEADER FLUORESCENT FIXTURE ASSY.
NO. 636 — LAZARIAN UPRIGHT — HEADER FLUORESCENT FIXTURE ASSY. — PARTS LIST
ORDER BY PART NUMBER ONLY
DESCRIPTION
FLUORESCENT BRKT. 18” COOL WHITE FLUORESCENT LAMP LAMP LOCKS (2 REQ'D.) FLUORESCENT SOCKET (2 REQ’D.) FLUORESCENT STARTER HOLDER W/WIRE LEADS #6-32 x 1/2 PHIL. RND. HD. M.S. (4 REQ’D.) #6 EXT. WASHER (4 REQ'D.) FLUORESCENT STARTER BALLAST #8-32 x 5/16 SLT. HEX HD. SCREW (4 REQ’D.) LINE FILTER ASSY. (NOT SHOWN) ITEM PART NO.
0595-00105-0000 0017-00003-0043 0017-00003-0445 0017-00031-0036 0017-00003-0412 0017-00101-0573 0017-00104-0009 0017-00003-0019 0017-00003-0026 0017-00101-0598 A961-00042-0000
5-1
NO. 636 — LAZARIAN UPRIGHT — FRONT
5-2
NO. 636 — LAZARIAN UPRIGHT — FRONT — PARTS LIST
ORDER BY PART NUMBER ONLY
0636-00900-00XF DISPLAY HEADER 0537-00903-0058 GLASS CHANNEL 6-15/16 (2 REQ’D.) 0636-00102-00XF RETAINING BRKT. (2 REQ’D.) 0017-00101-0138 #8 x 5/8 TORX TAMPER RESISTANT SCREWS (6 REQ'D.) 0017-00009-0522 LONG ARM KEY T-20 (FOR ABOVE SCREW) A595-00011-0000 HEADER FLUORESCENT LIGHT ASSY. 0017-00009-0393 BLACK SPEAKER GRILLE W/SLOTS 0017-00003-0430 6" x 9” SPEAKER 4 OHM 10W. 0017-00101-0136 #8-32 x 1-1/4 CARRIAGE BOLT (4 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (4 REQ’D.) 0508-00900-0000 TV. BEZEL 0508-00905-0000 T.V. PLEXI-GLASS (GRAYLITE #31) — 17-3/8" x 13-1/4” x 1/8” 0508-00901-0000 PLEXI-GLASS CLIPS (4 REQ’D.) 0017-00101-0017 #6 x 1/2 SLT. HEX HD. SCREW (4 REQ’D.) 0636-00901-00XF MAIN VIEWING GLASS 0508-00108-0000 GLASS STOP BRKT. — CABINET REAR 0017-00101-0027 #8 x 3/4 SLT. HEX HD. SCREW (3 REQ'D.) 0636-00904-00XF REAR SCENERY 0636-00905-0000 FRONT DECAL 0636-00906-0100 LEFT SIDE DECAL 0636-00906-0200 RIGHT SIDE DECAL A636-00006-0000 STRIKE TO CONTROL PANEL ASSY. 0961-00115-O00XF STRIKE (2 REQ’D.) 0017-00101-0620 #8-32 x 1/2 CARRIAGE BOLT (10 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (12 REQ'’D.) 0017-00009-0033 LATCH CLAMP (3 REQ'D.) 0017-00101-0141 #8 x 11/16 UNSLOT. HEX HD. SCREW (6 REQ’D.) 0550-00101-0100 CONTROL SHELF MTG. BRKT. — RIGHT 0550-00101-0200 CONTROL SHELF MTG. BRKT. — LEFT 0555-00901-0000 LOCATING PIN (4 REQ'D.) 0636-00903-0000 CONTROL SHELF OVERLAY — DECORATIVE A557-00006-0000 CONTROL ASSY. 0017-00032-0093 PUSH BUTTON SWITCH W/HOLDER (4 REQ’D.) 0017-00042-0299 YELLOW/RED SQUARE PUSH BUTTON ASSY. (4 REQ’D.) 0017-00103-0054 5/8-11 PAL NUT (4 REQ'D.) 0017-00032-0051 SMALL RED PUSH BUTTON SWITCH (2 REQ’D.) A090-00300-10BK U.S.A. 25¢ COIN DOOR ASSY. 0090-00002-04BK LARGE COIN DOOR FRAME 0017-00101-0121 #632 x 5/16 PHIL. TRS. HD. SCREW (3 REQ’D.) (MOUNTS COIN DOOR TO FRAME) 0935-00906-0100 KICK PLATE — 23” LONG 0017-00102-0048 3/8-16 x 2" LEG LEVELERS (4 REQ'D.) 0017-00103-0026 3/8-16 LEG LEVELER NUTS (4 REQ’D.)
5-3
NO. 636 — LAZARIAN UPRIGHT — REAR ACCESS
5-4
NO. 636 — LAZARIAN UPRIGHT — REAR ACCESS — PARTS LIST
A088-00013-0000 0894-00916-0000 0017-00003-0339
0017-00003-0439
0636-00101-0000 0017-00102-0006 0017-00104-0014 0017-00103-0018 0017-00101-0141 0555-00901-0000 0508-00900-0000 A088-00015-0000 A082-90421-B000 A084-91419-C636 0624-00902-0100 0624-00902-0500 A084-90911-E636 A084-91421-C636 A084-91422-B636 A961-00007-0000 0961-00109-0000 0017-00042-0255 0894-00702-00XF 0017-00100-0037 A950-00004-0000 A950-00006-0000 0950-00105-0000 0950-00104-0000 0950-00101-0000 0950-00900-0000 0017-00101-0142 0017-00104-0014 0017-00103-0018 A508-00023-0000
A636-00013-0000 A097-00009-0000 0017-00009-0490 3010-03003-0000 A636-00014-0000 A636-00017-0000 A636-00018-0000 A636-00012-0000 A636-00010-0000 A636-00016-0000 A636-00015-0000 A641-00011-0000 0508-00106-0000 0508-00108-0000 0017-00101-0027 ORDER BY PART NUMBER ONLY
PART NO. DESCRIPTION
ON/OFF SWITCH AND BRKT. ASSY. PLASTIC PULL AND VENT (2 REQ’D.) ELECTROHOME 19” COLOR DUAL SYNC. HORIZ. MTG. MONITOR (OR) WELLS GARDNER 19” COLOR DUAL SYNC. HORIZ. MTG. MONITOR MONITOR RAIL (2 REQ’D.) 1/4-20 x 3/4 SQR. NECK BOLT (4 REQ'D.) 7/8 DISH WASHER (4 REQ’D.) 1/4-20 HEX NUT (4 REQ’D.) #8 x 11/16 UNSLOT HEX HD. SCREW (8 REQ’D.) LOCATING PIN (4 REQ’D.) TV. BEZEL INTERLOCK SWITCH AND BRKT. ASSY. POWER SUPPLY PCB ASSY. GAME LOGIC BOARD ASSY. P.C. SUPPORT BRKT. 12” LG (4 REQ’D.) P.C. SUPPORT BRKT. 6-1/2" LG. (4 REQ’D.) SOUND BOARD ASSY. DIODE P.C. BOARD ASSY. MONITOR INTERFACE BOARD ASSY. CASTER ASSY. (2 REQ'D.) WHEEL BRKT. (2 REQ'D.) PLASTIC WHEEL (2 REQ'D.) SHAFT (2 REQ'D.) 3/8" E-RING (2 REQ’D.) COIN BOX ASSY. COIN BOX CRADLE ASSY. COIN BOX COVER COIN BOX HANDLE COIN DEFLECTOR (2 REQ’D.) LARGE PLASTIC CASH BOX 1/4-20 x 1-3/8 RND. HD. BOLT (4 REQ’D.) 7/8 DISH WASHER (4 REQ’D.) 1/4-20 HEX NUT (4 REQ'D.) 3 COND. LINE CORD ASSY.
ADDITIONAL PARTS LIST TRANSFORMER BOARD ASSY. BACK DOOR LOCK ASSY. 5-5/8" SQR. VENT GRILLE (4 REQ'D.) GROUNDING CLIP VIDEO SIGNAL CABLE ASSY. VIDEO SIGNAL ADAPTOR CABLE ASSY. AUDIO ADAPTOR CABLE ASSY. CONTROL SHELF CABLE ASSY. MASTER CABLE ASSY. COIN DOOR CABLE ASSY. HIGH VOLTAGE CABLE ASSY. LOW VOLTAGE CABLE ASSY. T.V. BEZEL MTG. BRKT. (2 REQ’D.) MAIN VIEWING GLASS STOP BRKT. #8 x 3/4 SLT. HEX HD. SCREW (3 REQ’D.)
5-5
NO. 641 — LAZARIAN MINI — FRONT
eas
5-6
NO. 641 — LAZARIAN MINI — FRONT — PARTS LIST
ORDER BY PART NUMBER ONLY
PART NO. DESCRIPTION
0641-00901-00XF DISPLAY HEADER 0537-00903-0060 GLASS CHANNEL 4-1/2" (2 REQ’D.) 0574-00100-00XF HEADER RETAINING BRKT. (2 REQ’D.) 0017-00101-0138 #8 x 5/8 TORX TAMPER RESISTANT SCREWS (8 REQ'D.) 0017-00009-0522 LONG ARM KEY T-20 (FOR ABOVE SCREW) A574-00007-0000 INSERT ASSY. 0017-00031-0030 WEDGE BASE LAMP SOCKET (5 REQ'D.) 0017-00003-0219 #194 LAMP 14V., .27A. (5 REQ'D.) 0017-00009-0393 BLACK SPEAKER GRILLE W/SLOTS 0017-00003-0430 6" x 9” SPEAKER 4 OHM, 10W. 0017-00101-0127 #8-32 x 1-1/2 CARRIAGE BOLTS (4 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (4 REQ’D.) 0641 -00900-00XF VIEWING GLASS 0537-00903-0056 GLASS CHANNEL 14-1/2” (2 REQ'D.) A555-00016-0000 GLASS CLAMPING PLATE 0641-00100-0000 CONTROL SHELF PLATE 0641-00902-0000 CONTROL SHELF OVERLAY 0017-00101-0620 #8-32 x 1/2 CARRIAGE BOLT (8 REQ'D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (8 REQ’D.) 0550-00101-0100 CONTROL SHELF MTG. BRKT. — RIGHT 0550-00101-0200 CONTROL SHELF MTG. BRKT. — LEFT 0555-00901-0000 PLASTIC LOCATING PIN (8 REQ’D.) 0017-00009-0033 LATCH CLAMP (2 REQ'D.) 0961-00115-OOXF STRIKE (2 REQ’D.) 0017-00101-0141 #8 x 11/16 UNSLOT HEX HD. SCREW (16 REQ’D.) 0017-00032-0051 RED SWITCH BUTTON (2 REQ’D.) 0017-00032-0093 PUSH BUTTON SWITCH W/HOLDER (4 REQ’D.) 0017-00042-0299 YELLOW/RED SQUARE PUSH BUTTON ASSY. (4 REQ'D.) 0017-00103-0054 5/8-11 PAL NUT A557-00006-0000 CONTROL ASSY. A090-00300-10BK U.S.A. 25¢ COIN DOOR ASSY. 0090-00002-04BK LARGE COIN DOOR FRAME 0935-00906-0400 KICK PLATE 0017-00102-0048 3/8-16 x 2 LEG LEVELERS (4 REQ’D.) 0017-00103-0026 3/8-16 LEG LEVELER NUTS (4 REQ’D.)
5-7
ACCESS NO. 641 — LAZARIAN MINI — REAR
a Se PARE : ee eee
5-8
NO. 641 — LAZARIAN MINI — REAR ACCESS — PARTS LIST
ORDER BY PART NUMBER ONLY
ITEM PART NO. DESCRIPTION
0017-00003-0430 6" x 9" SPEAKER 4 OHM, 10W. 0931-00903-0000 T.V. BEZEL 0934-00905-0000 PLEXI-GLASS A961-00026-0000 BEZEL MTG. BRKT. ASSY. 0017-00003-0340 ELECTROHOME — 13” COLOR DUAL SYNC. HORIZ. MTG. MONITOR (OR) 0017-00003-0435 WELLS GARDNER — 13” COLOR DUAL SYNC. HORIZ. MTG. MONITOR 0555-00100-0000 MONITOR MTG. BRKT. (2 REQ'D.) A088-00015-0000 INTERLOCK SWITCH & BRKT. ASSY. A950-00006-0000 COIN BOX CRADLE ASSY. 0950-00105-0000 COIN BOX COVER 0950-00104-0000 COIN BOX HANDLE 0950-00101-00XF COIN DEFLECTOR (2 REQ'D.) 0950-00900-0000 LARGE PLASTIC CASH BOX 0017-00101-0142 1/4-20 x 1-3/8 RND. HD. BOLT (4 REQ’D.) 0017-00104-0014 7/8 DISH WASHER (4 REQ’D.) 0017-00103-0018 1/4-20 HEX NUT (4 REQ'D.) A082-90421-B000 POWER SUPPLY P.C. ASSY. A084-91419-C636 GAME LOGIC BOARD ASSY. 0624-00902-0100 P.C. SUPPORT BRKT. 12” (4 REQ’D.) 0624-00902-0300 P. C. SUPPORT BRKT. 2-1/2" (2 REQ’D.) 0624-00902-0500 P.C. SUPPORT BRKT. 6-1/2” (2 REQ’D.) A084-90911-E636 SOUND BOARD ASSY. A084-91422-B636 MONITOR INTERFACE P.C. ASSY. A084-91421-C636 DIODE P.C. ASSY. A088-00013-0000 ON/OFF SWITCH & BRKT. ASSY. 0017-00009-0490 5-5/8" SQR. VENT GRILLE (4 REQ'D.)
ADDITIONAL PARTS LIST A097-00009-0000 BACK DOOR LOCK ASSY. A641-00012-0000 CONTROL SHELF CABLE ASSY. A641-00007-0000 MASTER CABLE ASSY. A636-00014-0000 VIDEO SIGNAL CABLE ASSY. A636-00017-0000 VIDEO SIGNAL ADAPTOR CABLE ASSY. A636-00018-0000 AUDIO ADAPTOR CABLE ASSY. A641-00006-0000 HIGH VOLTAGE CABLE ASSY. A641-00011-0000 LOW VOLTAGE CABLE ASSY. AS74-00015-0000 INSERT CABLE ASSY. A636-00016-0000 COIN DOOR CABLE ASSY. A508-00023-0000 3 COND. LINE CORD
5-9
NO. 646 — LAZARIAN COCKTAIL — FRONT
5-10
NO. 646 — LAZARIAN COCKTAIL — FRONT — PARTS LIST
ORDER BY PART NUMBER ONLY
0017-00009-0499 COVER GLASS — 32” x 22” x 1/4” 0646-00900-0000 ARTWORK UNDERLAY 0775-00104-00XF GLASS CLIPS (8 REQ'D.) 0017-00101-0117 #8 x 5/8 PHIL. TRS. HD, SCREW (16 REQ'D.) 0508-00905-0000 T.V. PLEXI-GLASS (GRAYLITE #31) — 17-3/8" x 13-1/4" x 1/8” 0557-00900-0000 T.V. BEZEL A646-00004-0100 CONTROL SHELF ASSY. — PLAYER #1 A646-00004-0200 CONTROL SHELF ASSY. — PLAYER #2 0017-00009-0393 BLACK SPEAKER GRILLE W/SLOTS (2 REQ’D.) 0017-00003-0430 6" x 9" SPEAKER 4 OHM, 10W. 0017-00101-0136 #8-32 x 1-1/4 CARRIAGE BOLT (8 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (8 REQ'D.) A090-00300-10BK U.S.A. 25¢ COIN DOOR ASSY. 0090-00002-02BK LARGE COIN DOOR FRAME 0017-00101-0121 #6-32 x 5/16 PHIL. TRS. HD. SCREW (3 REQ’D.) (MOUNTS COIN DOOR TO FRAME) 0017-00102-0048 3/8-16 x 2" LEG LEVELERS (4 REQ'D.) 0017-00103-0026 3/8-16 LEG LEVELER NUTS (4 REQ’D.)
5-11
NO. 646 — LAZARIAN COCKTAIL — INTERIOR ACCESS
5-12
NO. 646 — LAZARIAN COCKTAIL — INTERIOR ACCESS — PARTS LIST
ORDER BY PART NUMBER ONLY
ITEM PART NO. DESCRIPTION
0017-00003-0450 WELLS GARDNER — 19” COLOR DUAL SYNC HORIZ. MTG. MONITOR A557-00004-00XF MONITOR MTG. BRKT. ASSY. (2 REQ’D.) 0017-00101-0127 #8-32 x 1-1/2 CARRIAGE BOLT (4 REQ’D.) 0017-00104-0037 #8 FLAT WASHER (4 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (4 REQ'D.) 0017-00102-0002 1/4-20 x 1/2 SLT. HEX HD. BOLT (4 REQ'D.) 0017-00102-0052 1/4-20 x 1 UNSLOT HEX FLAT HD. BOLT (4 REQ’D.) 0017-00104-0014 7/8 DISH WASHER (8 REQ'D.) 0921-00107-00XF STRIKE (2 REQ’D.) 0017-00101-0769 #10 x 3/4 SLT. HEX HD. SCREW (4 REQ’D.) 0017-00009-0033 LATCH CLAMP (2 REQ'D.) 0017-00101-0141 #8 x 11/16 UNSLOT HEX HD. SCREW (4 REQ'D.) 0017-00009-0514 2-1/2" HINGE (2 REQ'D.) 0017-00101 -0628 #8-32 x 3/4 CARRIAGE BOLT (4 REQ'D.) 0017-00101-0639 #8-32 x 1-1/4 CARRIAGE BOLT (4 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (4 REQ'D.) 0557-00900-0000 BEZEL 0646-00102-01XF CONTROL SHELF — PLAYER #1 0646-00102-02XF CONTROL SHELF — PLAYER #2 0510-00101-00XF BOTTOM PAN (2 REQ’D.) A557-00006-0000 CONTROL ASSY. (2 REQ’D.) A646-00012-0100 CONTROL SHELF CABLE ASSY. — PLAYER #1 A646-00012-0200 CONTROL SHELF CABLE ASSY. — PLAYER #2 0017-00042-0306 RED/YELLOW PUSH BUTTON ASSY. (8 REQ'D.) A646-00006-0000 SWITCH MTG. BRKT. ASSY. (2 REQ'D.) A646-00007-0000 SWITCH ASSY. (8 REQ’D.) 0017-00103-0054 §/8-11 PAL NUT 0017-00032-0051 SMALL RED BUTTON SWITCH (2 REQ'D.) PLAYER #1 PANEL ONLY 0930-00104-0000 CONTROL PANEL LOCATING BRKT. (4 REQ'D.) 0017-00101-0025 #8 x 1/2 SLT. HEX HD. SCREW (16 REQ’D.) 0930-00904-0000 LIGHT SHIELD (2 REQ’D.) 0017-00031-0044 WEDGE BASE LAMP SOCKET (4 REQ'D.) 0017-00003-0219 #194 LAMP 14V., .27A. (4 REQ’D.) 0017-00101-0555 #6-32 x 5/16 SLT. HEX HD. SCREW (4 REQ'’D.) 0017-00003-0430 6” x 9” SPEAKER 4 OHM, 10W. A646-00009-0000 TRANSFORMER BOARD ASSY. A082-90421-B000 POWER SUPPLY PC ASSY. A084-91419-C636 GAME LOGIC BOARD ASSY. 0624-00902-0100 P.C. SUPPORT BRKT. 12” LG. (4 REQ'D.) 0624-00902-0300 P.C. SUPPORT BRKT. 2-1/2” LG. 0624-00902-0500 P.C. SUPPORT BRKT. 6-1/2” LG. (3 REQ'D.) A084-9091 1-E636 SOUND BOARD ASSY. A084-91421-C636 DIODE P.C. ASSY. A084-91422-B636 MONITOR INTERFACE P.C. BOARD ASSY.
5-13
NO. 646 — LAZARIAN COCKTAIL — INTERIOR ACCESS — PARTS LIST (Continued)
ORDER BY PART NUMBER ONLY
ITEM PART NO. DESCRIPTION
ADDITIONAL PARTS LIST
A775-00013-0000 FAN ASSEMBLY 0151-00081-0000 4" FAN 0775-00110-O00XF FAN PLATE 0749-00106-00XF VENT SCREEN 0017-00101-0347 #6-32 x 1/2 R.H.MLS. (4 REQ’D.) 0017-00104-0009 #6 EXT. WASHER (4 REQ'D.) 0017-00103-0005 #6-32 HEX NUT (4 REQ’D.) 0017-00101-0026 #8 x 5/8 SLT. HEX HD. SCREW (4 REQ’D.) A088-00013-0000 ON/OFF SWITCH & BRKT. ASSY. A927-00019-0000 COIN BOX ASSY. A962-00004-0000 COIN BOX COVER ASSY. A962-00005-0000 COIN BOX SIDE CHANNEL ASSY. — SHORT 0962-00101-0000 COIN BOX SIDE CHANNEL — SHORT 0017-00101-0628 #8-32 x 3/4 CARRIAGE BOLT (4 REQ’D.) 0017-00104-0022 #8 WASHER (4 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (4 REQ’D.) A088-00014-0000 INTERLOCK SWITCH & BRKT. ASSY. 0927-00907-0000 HIGH VOLTAGE SHIELD — FORMED A646-00010-0000 MASTER CABLE ASSY. A646-00011-0000 HIGH VOLTAGE CABLE ASSY. A646-00014-0000 LOW VOLTAGE CABLE ASSY. A636-00016-0000 COIN DOOR CABLE ASSY. A636-00014-0000 VIDEO SIGNAL CABLE ASSY. A636-00017-0000 VIDEO SIGNAL ADAPTOR CABLE ASSY. A636-00018-0000 AUDIO ADAPTOR CABLE ASSY. A927-00005-0000 HIGH BASE LEG KIT ASSY. — OPTIONAL A508-00023-0000 3 COND. LINE CORD ASSY.
5-14
LAZARIAN TRANSFORMER BOARD ASSY. — PARTS LIST (NO PHOTOGRAPH)
ORDER BY PART NUMBER ONLY
DESCRIPTION
TRANSFORMER — UPRIGHT & MINI POWER TRANSFORMER 120/240V. — UPRIGHT & MINI SHIELDED TRANSFORMER 115/220V. — COCKTAIL ONLY TRANSFORMER W/MAGNETIC SHIELD — COCKTAIL ONLY 2 POSITION FUSE CLIP ASSY. (1 REQ’D. U/R & C/T, 2 REQ'D. MINI) 3 POSITION FUSE CLIP ASSY. — UPRIGHT & COCKTAIL SLO BLO FUSE 1/2A., 250V. — UPRIGHT & COCKTAIL SLO BLO FUSE 2A., 250V. (3 REQ’D. U/R & MINI, 2 REQ’D. C/T) SLO BLO FUSE 2-1/2A., 250V. ( 1 REQ’D. MINI, 2 REQ’D. C/T) SLO BLO FUSE 1-1/2A., 250V..— UPRIGHT 115V. CONVENIENCE OUTLET 2 LEAD TRANSFORMER BOARD FILTER ASSY. 3 COND. LINE CORD TERMINAL STRIP MALE CONNECTOR — 5 PAIR GROUND STRAP 5-1/2" — UPRIGHT GROUND STRAP 36” — UPRIGHT GROUND STRAP 48” — MINI GROUND STRAP 30” — MINI GROUND STRAP — MINI GROUND STRAP — COCKTAIL GROUND STRAP — 3” — COCKTAIL ITEM PART NO.
MT00-00092-0000 MT00-00087-0000 MT00-00091-0000 MT00-00093-0000 0720-00001-0200 0720-00001 -0300 0017-00003-0002 0017-00003-0004 0017-00003-0217 0017-00003-0261 A151-00079-0000 A508-00037-0000 0017-00003-0064 3010-13106-0000 0017-00021-0370 3000-17246-0500 3000-17246-1000 3000-17246-0900 3000-17246-1100 3010-04237-0100 3000-17246-0200 3010-04044-0000
LAZARIAN — CONTROL ASSEMBLY — ALL VERSIONS
5-16
LAZARIAN — CONTROL ASSEMBLY — ALL VERSIONS — PARTS LIST
ORDER BY PART NUMBER ONLY
| 1 | A932-00022-0000 | BALL & SHAFT ASSEMBLY |
| 2 | 0017-00100-0025 | 1/4" E-RING |
| 3 | 0921-00702-0000 | STOP SPACER |
| 4 | 0921-00902-0000 | SLIDE PLATE |
| 5 | A557-00005-0000 | SPOT WELD ASSEMBLY |
| 6 | 0017-00101-0637 | #8-32 x 1” CARRIAGE BOLT (4 REQ’D.) |
| 7 | 0017-00103-0061 | #8-32 HEX NUT W/SEMS (4 REQ'D.) |
| 8 | 0932-00902-0000 | GROMMET |
| 9 | 0017-00101-0598 | #8-32 x 5/16 SLT. HEX HD. M.S. (10 REQ'D.) |
0962-00904-0000 SLEEVE 0017-00101-0527 0020-00202-0000 A932-00009-0000 A921-00009-0000 0927-00908-0000 0921-00700-0000 #5-40 x 5/8 SLT. RND. HD. SCR. (8 REQ’D.) SWITCH PLATE (4 REQ’D.) SWITCH ASSEMBLY (4 REQ’D.) STOP PLATE & SWITCH BRKT. ASSY. WEAR PLATE ACTUATOR
5-17
IBLY — U.S.A. 25¢ FRONT DOOR ASSEM
FRONT DOOR ASSEMBLY — U.S.A. 25¢
ORDER BY PART NUMBER ONLY
0090-00002-028K DOUBLE ENTRY COIN DOOR FRAME 0017-00101-0121 #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ’D.) A090-00073-02BK DOUBLE ENTRY COIN DOOR W/DRESS PLATE 0017-00101-0123 #8 x 1/4 UNSLOT. HEX HD. SCREW (4 REQ’D.) 0017-00007-0019 KEY HOOK 0017-00101-0552 #6-32 x 1/4 CARRIAGE BOLT (4 REQ'D.) 0090-00117-03XF COIN ENTRY PLATE — 25¢ (2 REQ’D.) AC97-00005-0000 DOOR LOCK & KEY W/SCREW & NUT (OR) A097-00006-0000 DOOR LOCK & KEY W/SCREW & NUT 0090-00128-00XF DOOR TILT SWITCH BRKT. 0017-00005-0041 DOOR CAM A090-00096-0000 DOOR TILT SWITCH 0090-00126-01XF SWITCH BACK-UP PLATE 0017-00101-0525 #5-40 x 9/16” PHIL. HD. M.S. (2 REQ'D.) A090-00096-0000 DOOR TILT SWITCH & BRKT. ASSY. (ITEMS 9 & 11 THRU 13) 0090-00903-9500 25¢ WINDOW (2 REQ’D.) 0090-00143-00XF COIN PLEX RETAINER 0017-00003-0219 12 VOLT LAMP — G.E. #194 (2 REQ'D.) 0017-00031-0048 WEDGE SOCKET W/BRKT. (2 REQ’D.) 0017-00103-0084 #6-32 HEX NUT W/SEMS (4 REQ’D.) A090-00089'0000 COIN METER W/DIODE 0017-00101-0124 #6 x 1/4 UNSLOT. HEX HD. SCR. (8 REQ’D.) 0017-00032-0051 PUSH BUTTON SWITCH 0017-00032-0007 SLIDE SWITCH 0017-00072-0034 STEEL OVAL HD. RIVET 0090-00173-0000 COIN COUNTER MTG. BRKT. A090-00082-0100 TEST SWITCH & BRKT. ASSY. (ITEMS 23 THRU 25) A090-00087-0000 COIN CHUTE & TOP ASSY. (2 REQ'D.) 0010-00134-0000 SPRING 0010-00181-0000 SPRING 0017-00007-0083 1/8 x 1-5/8 ROLL PIN 0090-00129-00XF PIVOT POST 0090-00167-00XF PIVOT LEVER 0093-00155-O00XF REJECT LEVER 0017-00100-0018 E-RING A090-00088-0000 REJECT LEVER ASSY. (2 REQ'D.) (ITEMS 30 THRU 33) A090-00085-0000 COIN ACCEPTOR FRAME ASSY. (2 REQ’D.) 0017-00005-0003 COIN ACCEPTOR W/STRING CUTTER (2 REQ’D.) (OR) 0017-00005-0211 COIN ACCEPTOR W/ANTI STRING DEVICE (2 REQ’D.) (OR) 0017-00005-0214 COIN ACCEPTOR W/STRING CUTTER (2 REQ’D.) A090-00064-0000 ANTI-PENNY DEVICE 0017-00101-0099 #6 x 1/4 SLT. HEX HD. M.S. (2 REQ'D.) 0090-00162-00XF COIN SWITCH MTG. BRKT. 0017-00005-0203 COIN SWITCH CHUTE 0017-00005-0195 COIN SWITCH 0010-00599-0000 COIN SWITCH WIRE 0017-00007-0132 PUSH-ON RING A090-00059-0400 COIN SWITCH & WIRE ASSY. (ITEMS 40 THRU 42) 0017-00101-0698 #4-40 x 3/4 SLT. RND. HD. M.S. (2 REQ'D.) A090-00077-0000 COIN GUIDE & SWITCH ASSY. (ITEMS 38 THRU 43) OWMANMAAHAHRON=
5-19
VI Technical Troubleshooting
Introduction
The most common problems occur in harness components such as the coin acceptor, player controls, interconnecting wiring, etc. The TV monitor and PCB computer cause their share of problems too, but not as much as the harness and its component parts. TV monitor troubleshooting will not be covered here because it is covered in that section of this manual. .
As you already know, the PCB computer is a complex device with a number of different circuits. Some circuits remain basically the same among games, but overall there are a great many differences between them. PCB troubleshooting procedures, therefore, can be lengthy and will differ greatly among games. However, some basic Z-80 CPU information is involved in this section.
General Suggestions
The first step in any troubleshooting procedure is correctly identifying the malfunction’s symptoms. This includes not only the cifcuits or features malfunctioning, but also those still operational. A carefully trained eye will pick up other clues as well. For instance, a game in which the computer functions fail completely just after money was collected may have a quarter shorting the PCB traces. Often, an experienced troubleshooter will be able to spot the cause of the problem even before opening the cabinet. After all the clues are carefully considered, the possible malfunctioning areas can be narrowed down to one or two good suspects. Those areas can be examined by a process of elimination until the cause of the malfunction is discovered.
Harness Component Troubleshooting
Typical problems falling in this category are coin and credit problems, power problems and failure of individual features. NO GAME CREDIT For example, your prospective player inserts his quarter and is not awarded a game. The first item to check ‘is if the quarter is returned. If the quarter is returned, the malfunction most certainly lies in the coin acceptor itself. First, use a set of test coins (both old and new) to ascertain that the player's coin is not undersize or underweight. If your test coins are also returned, coin acceptor servicing is indicated. Generally, the cause of this particular problem is a maladjusted magnet gate. Normally, this will mean slightly closing the magnet gate alittle by turning the adjusting screw out a bit (see section on coin acceptor for more details). If the quarter is not returned and there is no game credit, the cause of the malfunction may be in one of several areas. First try operating the coin return button; if the coin is returned, the problem is most likely in the magnet gate. Enlarge the gap according to the coin acceptor service procedures. If this does not cure the problem, remove the coin acceptor, clean it and perform the major adjustment procedure. If the trapped coin is not returned when the wiper lever is actuated, you may have an acceptor jammed by a slug, gummed up with beer, a jammed coin chute, or mechanical failure of the acceptor mechanism. In this case, first check for the slug that will generally be trapped against the magnet. If so, simply remove the slug and test the acceptor. If the chute is blocked, remove the acceptor and remove the jammed coins. If there is actual failure of the acceptor, remove the unit and repair as indicated in the coin acceptor service procedures. If the coin is making its way through the acceptor (that is, falling into the coin box), yet there is still no game credit, you either have a mechanical failure of the coin switch or electrical failure of the coin and credit circuits. The first place to begin is by checking the coin switch. Most of these switches are the make/break variety of micro switch, which is checked by testing for continuity between the NO, NC, and C terminals. When not actuated, the NC and C terminals should be continuous and the NO terminal open. When operated, the NO and C terminals should close and the NC should be open. If the coin switch checks out, examine the connections to the terminals to make sure there is good contact. If necessary, use the continuity tester and check from the terminal lug on the switch to the associated PCB trace. This will tell you if there is a continuous line all the way to the credit circuit.
If the coin switch wires do not check out, the problem is in the computer — most likely in the coin and credit circuitry. if you do get game credit when a coin is deposited, but the game will not start when the start switch is Pressed, you may have a problem in the start switch, the interconnecting wiring or in the computer. First check the switch. If the switch is OK, proceed to check the wiring. Again, make sure you go from the terminal |ug on the switch to the PCB trace. This way, you will check the terminal contact as well as PCB edge connector contact. If the wiring is continuous, proceed to check the PCB credit circuit. If not, check each section of the wiring, until the discontinuity is located. If the wiring is OK, the problem must lie in the computer.
Transformer and Line Voltage Problems
Your machine must have the correct line voltage to operate properly. If the line voltage drops too low, a circuit in the computer will disable game credit. The point at which the computer will fail to work will vary
some from game to game, but no game'will work on
line voltage that drops below 105 VAC. Low line voltage may have many causes. Line voltage normally fluctuates a certain amount during the day as the total usage varies. Peak usage times occur mainly at dawn or dusk, so if your machine's malfunction seems to be related to the time of day, this may be a factor. A large load connected to the same line as the game (such as a large air conditioner or other device with an exceptionally large motor) may drop the line voltage significantly when starting up. This drop can result in an intermittent credit problem. In addition, poor connections in the location wiring, plug, or line cord may also cause a significant drop in power. Cold solder joints in the game's harness, especially in areas like the transformer connections, interlock switch, or fuse block, may also produce the same results, although probably on a more permanent basis. Sometimes location owners (especially in bars) replace light switches with dimmer rheostats, and the game is sometimes on the same line. Obviously, the voltage available to the game is going to drop dramatically when the dimmer is turned. In any case, the way to check for correct line voltage is with your VOM. Set the VOM to 250 VAC and stick the probes in the wall receptacle. If it's OK here, check the transformer primary connections. If you do not get 117 VAC, examine the solder joints on the transformer, fuse block, and interlock switch. If you do get 117 VAC, the problem must be either in the transformer, harness connections, or in the PCB power supply. If you suspect the transformer, check its secondaries with the VOM set to 50 VAC and correlate the readings with the legend on the side of the transformer. The transformer must also be correctly grounded, so check the ground potential as well, especially if there is a hum bar rolling up or down the TV screen.
HARNESS PROBLEMS Other harness problems include blowing fuses and malfunctioning controls. The repeating blown-fuse problem can sometimes be quite exasperating to solve, for short circuits have the tendency to occur in areas almost impossible to find. First, try inserting a new fuse, as old fuses age and blow without cause. If the new one also blows, you definitely have a short. The best way to approach this problem is by turning the power off and disconnecting devices that may be causing the problem, such as the TV, transformer, and PCB. Disconnect the devices by pulling off their connectors, but do not allow them to touch. If necessary, insulate them with small pieces of electrical tape. Then, connect your VOM across the terminals of the fuse block (all electrical power shut off), and set it to one of the resistance scales. This will save blowing a fuse each time you want to check the circuit. if the VOM reveals that disconnecting the devices removed the short, reconnect the devices one by one until the short returns. The last device connected is the one that is at fault. If the VOM reads a short even after the devices are disconnected, the fault must lie in the harness itself, and only patient exploration will reveal its location. First, carefully examine all the wiring, looking for terminals that may be touching, metal objects such as coins shorting connections or burned insulation. If necessary, use the VOM to check each suspected wire. MALFUNCTIONING CONTROLS One of the most common problems here is a bad potentiometer. Typically, a bad pot will cause the image to jump as it reaches a certain point. The only cure for this one is to install a new pot. If a feature that is operated by a switch (for example, joysticks, foot pedals, control panel buttons) does not operate at all, check the switch with a VOM or continuity tester to verify its operation. If the switch does not check out, replace it. If the switch is OK, you should suspect the input to the switch from the PCB. In this case, get out the harness and logic schematics and check to see what kind of input it is. In many cases, the input will be +5 VDC. If so, use the VOM to check its presence. Normally, the switch is used to pull a +5 VDC line LOW to GND or to pulla LOW line HIGH. If the PCB output is missing, check the wire length from the PCB. If you find the signal at the PCB trace, the wire length or connection is at fault. If not, begin exploring the PCB using the logic schematics.
A Glossary of Microprocessor Terms
MICROPROCESSOR — one or several microcircuits that perform the function of a computer's CPU. Sections of the circuit have arithmetic and comparative functions that perform computations and executive instructions. CPU — central-processing unit. A computing system's “brain”, whose arithmetic, control and logic elements direct functions and perform computations. The microprocessor section of a microcomputer is on one chip or several chips. PROM — programmable read-only memory. User permanently sets binary on-off bits in each cell by selectively fusing or not fusing electrical links. Nonerasable. Used for low-volume applications. EPROM — erasable, programmable, read-only memory. Can be erased by ultraviolet light bath, then reprogrammed. Frequently used during design and development to get programs debugged, then replaced by ROM for mass production. ROM — read-only memory. The program, or binary on-off bit pattern, is set into ROM during manufacture, usually as part of the last metal layer put onto the chip. Nonerasable. Typical ROM's contain up to 16,000 bits of data to serve as the microprocessor’s basic instructions. RAM — random-access memory. Stores binary bits as electrical charges in transistor memory cells. Can be read or modified through the CPU. Stores input instructions and results. Erased when power is turned off. LSI — targe scale integration. Formation of hundreds or thousands of so-called gate circuits on semiconductor chips. Very large scale integration (VLS) involves microcircuits with the greatest component density. MOS — metal-oxide semiconductor. A layered construction technique for integrated circuits that achieves high component densities. Variations in MOS chip structures create circuits with speed and low-power requirements, or other advantages (static will damage a MOS chip).
Introduction to the
Z-80 CPU
The term “microcomputer” has been used to describe virtually every type of small computing device designed within the last few years. This term has been applied to everything from simple “microprogrammed” controllers constructed out of TTL MSI up to low end minicomputers with a portion of the CPU constructed out of TTL LSI “bit slices.” However, the major impact of the LSI technology within the last few years has been with MOS LSI. With this technology, it is possible to fabricate complete and very powerful computer systems with only a few MOS LSI components. The Zilog Z-80 family of components can be configured with any type of standard semiconductor memory to generate computer systems with an extremely wide range of capabilities. For example, as few as two LSI circuits and three standard TTL MSI packages can be combined to form a simple controller. With additional memory and I/O devices a computer can be constructed with capabilities that only a minicomputer could previously deliver. New products using the MOS LSI microcomputer are being developed at an extraordinary rate. The Zilog Z-80 component set has been designed to fit into this market through the following factors:
6-3
- The Z-80 is fully software compatible with the popular 8080A CPU. . Existing designs can be easily converted to include the Z-80. The Z-80 component set is at present superior in both software and hardware capabilities to any other microcomputer system on the market today. For increased throughput the Z80A operating ata 4 MHZ clock rate offers the user significant speed advantages. Microcomputer systems are extremely simple to construct using Z-80 components. Any such system consists of three parts:
- CPU (Central Processing Unit)
- Memory
- Interface Circuits to peripheral devices The CPU is the heart of the system. Its function is to obtain instructions from the memory and perform the desired operations. The memory is used to contain instructions and in most cases data that is to be processed. For example, a typical instruction sequence may be to read data from a specific peripheral device, store it in a location in memory, check the parity and write it out to another peripheral device. Note that the Zilog component set includes the CPU and various general purpose 1/O device controllers, while a wide range of memory devices may be used from any source. Thus, all required components can be connected together in a very simple manner with virtually no other external logic.
General Purpose Registers
There are two matched sets of general purpose registers, each set containing six 8-bit registers that may be used individually as 8-bit registers or as 16bit register pairs by the programmer. One set is called BC, DE and HL while the complementary set is called BC’, DE’ and HL’. At any one time the programmer can select either set of registers to work with through a single exchange command for the entire set. In systems where fast interrupt response is required, one set of general purpose registers and an accumulator/flag register may be reserved for handling this very fast routine. Only a simple exchange command need be executed to go between the routines. This greatly reduces interrupt service time by eliminating the requirement for saving and retrieving register contents in the external stack during interrupt or subroutine processing. These general purpose registers are used for a wide range of applications by the programmer. They also simplify programming, especially in ROM based systems where little external read/write memory is available. Arithmetic & Logic Unit (ALU) The 8-bit arithmetic and logical instructions of the CPU are executed in the ALU. Internally the ALU communicates with the registers and the external data bus on the internal data bus. The type of functions performed by the ALU include: Add Left or right shifts or rotates (arithmetic and logical)
Subtract Increment
Logical AND Decrement Logical OR Set bit Logical Exlusive OR Reset bit Compare Test bit Instruction Register and CPU Control As each instruction is fetched from memory, it is placed in the instruction register and decoded. The control sections performs this function and then generates and supplies all of the control signals necessary to read or write data from or to the registers, control the ALU and provide all required external control signals.
Z-80 CPU Pin Description
The Z-80 CPU is packaged in an industry standard 40 pin Dual In-Line Package. The I/O pins are shown in the below figure and the function of each is described.
MREQ <—— SYSTEM 7 iona «2 CONTROLS 55 2 1D —_ “
aFSH =——
HALT <——
cpu walt) ———} CONTROL int =—S | NMi te RESET ———> CPU ‘BUSRO Ta" BUS ausak «7 CONTROL
+5V GND Z-80 CPU
Z-80 PIN CONFIGURATION 8 a, ADDRESS BUS
oe DATA
9 Ds
Ao-Ais (Address Bus) Tri-state output, active high. Ao-A;s constitute a 16bit address bus, The address bus provides the address for memory (up to 64K bytes) data exchanges and for I/O device data exchanges. !/O
addressing uses the 8 lower address bits to allow the
user to directly select up to 256 input or 256 output ports. Ap is the least significant address bit. During refresh time, the lower 7 bits contain a valid refresh address.
Dy-D; (Data Bus) Tri-state input/output, active high. Dp-D; constitute an 8-bit bidirectional data bus. The data bus is used for data exchanges with memory and |/O devices.
M, : (Machine Cycle one)__ Output, active low. M, indicates that the current machine cycle is the OP code fetch cycle of an instruction execution. Note that during execution of 2-byte op-codes, M1 is generated as each op code byte is fetched. These two byte op-codes always begin with CBH, DDH, EDH or FDH. M1 also occurs with IORQ to indicate an interrupt acknowledge cycle. MREQ (Memory Request) Tri-state output, active low. The memory request signal indicates that the address bus holds a valid address for a memory read or memory write operation. 1ORQ (Input/Output Request) Tri-state output, active low. The 1ORQ signal indicates that the lower half of the address bus holds a valid 1/O address for a I/O read or write operation. An IORQ signal is also generated with an M1 signal when an interrupt is being acknowledged to indicate that an interrupt response vector can be placed on the data bus. Interrupt Acknowledge operations occur during M, time while I/O operations never occur during M, time. RD (Memory Read) _ Tri-state output, active low. RD indicates that the CPU wants to read data from memory or an I/O device. The addressed 1/O device or memory should use this signal to gate data onto the CPU data bus. WR (Memory Write) _ Tri-state output, active low. WR indicates that the CPU data bus holds valid data to be stored in the addressed memory or I/O device.
6-5 RFSH (Refresh) Output, active low. RFSH indicates that the lower 7 bits of the address bus contain a refresh address for dynamic memories and the current MREQ signal should be used to do a refresh read to all dynamic memories.
HALT (Halt state) Output, active low. HALT indicates that the CPU has executed a HALT software instruction and is awaiting either a non maskable or a maskable interrupt (with the mask enabled) before operation can resume. While halted, the CPU executes NOP’s to maintain memory refresh activity. WAIT (Wait) Input, active low. WAIT indicates to the Z-80 CPU that the addressed memory or I/O devices are not ready for a data transfer. The CPU continues to enter wait states for as long as this signal is active. This signal allows memory or I/O devices of any speed to be synchronized to the CPU. INT (Interrupt Request) Input, active low. The Interrupt Request signal is generated by I/O devices. A request will be honored at the end of the current instruction if the internal software controlled interrupt enable flip-flop (IFF) is enabled and if the BUSRQ signal is not active. When the CPU_accepts the interrupt, an acknowledge signal (IORQ during M, time) is sent out at the beginning of the next instruction cycle. The CPU can respond to an interrupt in three different modes that are described in detail in section 5.4 (CPU Control Instructions). NMI (Non-Maskable Interrupt) Input, negative edge triggered. The non maskable interrupt request tine has a higher priority than INT and is always recognized at the end of the current instruction, independent of the status of the interrupt enable flip-flop. NMI automatically forces the Z-80 CPU to restart to location 0066n. The program counter is automatically saved in the external stack so that the user can return to the program that was interrupted. Note that continuous WAIT cycles can prevent_the current instruction from ending, and that a BUSRQ will override a NMI. RESET Input, active low. RESET forces the program counter to zero and initializes the CPU. The CPU initialization includes:
- Disable the interrupt enable flip-flop
- Set Register |= 00H
- Set Register R =00n
- Set Interrupt Mode 0 During reset time, the address bus and data bus go to a high impedance state and all control ouput signals go to the inactive state.
BUSRQ (Bus Request) Input, active low. The bus request signal is used to request the CPU address bus, data bus and tri-state output control signals to go to a high impedance state so that other devices can control these buses. When BUSRQ is activated, the CPU will set these buses to a high impedance state as soon as the current CPU machine cycle is terminated.
BUSAK (Bus Acknowledge) Output, active low. Bus acknowledge is used to indicate to the requesting device that the CPU address bus, data bus and tri-state control bus signals have been set to their high impedance state and the external device can now control these signals.
CLK (Clock) Single phase TTL level clock which requires only a 330 ohm pull-up resistor to +5 volts to meet all clock requirements. —K—KSKD=@[@{*={="{=*]]]]]]]]_]_ee_eeeeE=
6-6
Vil. Coin Door Maintenance
SPECIAL NOTE: If you have any questions about the coin acceptors in your game(s), please feel free to contact their manufacturers. Each manufacturer's name is PROMINENTLY imprinted on every acceptor mechanism. Metal mechanisms only: COIN MECHANISMS, INC. 817 industrial Drive Elmhurst, IL 60126 Phone (312) 279-9150 Metal and Plastic mechanisms: COINCO COIN ACCEPTORS, INC. 860 Eagle Drive Bensenville, {L 60106 Phone (312) 766-6781
COIN DOOR MAINTENANCE
METAL COIN ACCEPTOR MECHANISMS
Periodically, the metal coin acceptor mechanism(s) must be removed from the coin door and cleaned.
- Make sure the power to the game is off.
- Unlock and open the coin door.
TO REMOVE PUSH LATCHES DOWN
PLACE PEGS IN SLOTS TO REPLACE PULL MECHANISM OUT . Remove the coin acceptor mechanism as shown in Figure 7-1. D Push down on the two spring loaded latches. O While holding the tatches down, pull the top of the coin acceptor mechanism toward you. O Release the latches and lift out the coin acceptor mechanism.
PUSH MECHANISM IN
Figure 7-1 Removing and replacing coin acceptor
- Clean the magnet of all foreign particles. See Figure 7-2. 0 This may be accomplished by swinging the gate open as shown in the above figure. 5, Remove the cradles and undersize levers and clean the bushings. (A pipe cleaner makes a good bushing cleaner.) O Also clean the pivot pin.
- Whenever needed, the coin acceptor should be cleaned with hot water and cleanser in the following manner: O Place the coin acceptor in boiling water for about ten minutes.
O Next, use a brush and kitchen cleaner to remove all remaining foreign matter from the unit. D Rinse the coin acceptor in clean boiling water. O Dry the coin acceptor thoroughly by using filtered compressed air to blow it dry.
GATE OPEN AS SHOWN CLEAN MAGNET BY DRAGGING A SCREWDRIVER BLADE ACROSS SURFACE
Figure 7-2 Cleaning the metal coin acceptor
7-2
- To lubricate the coin acceptor: O Use ONLY powdered graphite and put it ONLY on the moving parts of the coin acceptor. These parts are called out in Figure 7-3. O Be extremely careful to keep the powdered graphite away from paths that are traveled by the coins.
- WARNING — DO NOT USE OIL TO LUBRICATE THE COIN ACCEPTOR.
- Check the coin chute for obstructions such as: paper, gum, etc.
- Reinstall the coin acceptor to the coin door. See Figure 7-1. U Place the two pegs at the coin acceptor's base into their retaining slots. O Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches.
- Close and lock the coin door.
APPLY POWDERED GRAPHITE HERE
CRADLE
Figure 7-3 Lubricating the metal coin acceptor
SQUEEZE PINS TOGETHER TO UNLOCK S OPEN
HOLDING BOTH GATES TOGETHER, PUSH UP AND PULL OUT
Figure 7-4 Opening the plastic coin acceptor
PLASTIC COIN ACCEPTOR MECHANISMS
The plastic coin acceptor mechanism(s) must be removed periodically from the coin door and cleaned.
- Make sure the power to the game is off.
- Unlock and open the coin door.
- Remove the coin acceptor mechanism(s) as shown in Figure 7-1. O Push down on the two spring loaded latches. QO While holding the latches down, pull the top of the acceptor mechanism toward you. C Release the latches and lift out the mechanism.
- Squeeze the two pins indicated in Figure 7-4 together to open the mechanism and break it down into its three basic parts. O Clean the mechanism in hot soapy water. It never rusts. O Rinse the mechanism in clean hot water and atiow it to dry.
7-3 O Reassemble the mechanism (it never needs lubrication).
- Check the coin chute for obstructions such as: paper, gum, etc.
- Reinstall the coin acceptor to the coin door. See Figure 7-5, O Place the two pegs at the coin acceptor’s base into their retaining slots. O Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches.
- Close and lock the coin door.
ACCEPTOR CAN BE SET TO ACCEPT U.S. QUARTERS ONLY OR BOTH U.S. AND CANADIAN QUARTERS.
——————_ ?
SLIDE MAGNET TO EXTREME RIGHT (AS SHOWN) TO ACCEPT BOTH U.S. AND CANADIAN QUARTERS.
rs
TO ACCEPT U.S. QUARTERS ONLY, SLIDE MAGNET TO EXTREME LEFT.
Figure 7-5 Changing the plastic coin acceptor to accept American or Canadian quarters.
NOA ANVHL INOA d13H OL AQVAY GNVLS SHOLNEIHLSIG HNO GNV 44V.LS HNO “SdadVd SAWVD YNOA HLIM GACIAOUd HAEWNN Jays TIOL AHL LV ANVdWOD DNIEYNLOVANNVW AVMCIN YO YOLNEIYLSIG YNOA LOVLNOO ASW31d ‘SNOILSANO SAVH THLS GNV NOILOAS SIHL HONOYHL AVS" NOA Jl "HOLINOW ‘AL SAWVD YISHL ONIYIWdaY GNV DNILOOHSATIENOUL NI 3SAYDAC SOINOY.LOA13 NV LNOHLIM SSOHL Civ OL GAGN3LNI SI GNV YANNVW ONVLSHSCNN OL ASVA NV NI G10.L SI NOILOAS SIHL NI GANIVLNOO NOILVWHOSNI SHL 'HLON ASV31d
Color T.V.
Color T.V Monitor
Introduction: (How to use this section of your manual.)
This section has been designed to simply familiarize you with one of the more mystical components in your game — the T.V. monitor. If you are an electronics technician who is quite knowledgeable on the subject, you may decide to just go to the schematics and start troubleshooting the defective monitor. But if you are like most people, a monitor is a T.V. set, and that means a complex doo-dad that means big buck repairs. This isn't necessarily so. This section of the manual will acquaint you with the monitor and could just heip you repair it if you feel adventurous enough to give it a try. If you have any knowledge of electronics, especially the use of a voltmeter, the repairs you can make are astonishing. Just keep in mind that ELECTRICITY CAN BE VERY DANGEROUS, SO BE CAREFUL!
If you want to understand how a monitor works, just tead the “THEORY OF OPERATION” subsection. If you wish, you can follow along with the schematics. The information is presented in a very basic manner but more complete treatment of the subject can be found in the technical sections of bookstores.
If you want to attempt to repair your monitor, itwould be a good idea to read this whole section beginning to end before starting. Pay attention to all warnings
8-1 and take them seriously. The more equipment you have the better, but a low cost Volt-Ohm-Milliameter can often, do the trick. Here are the steps to take:
- Find the symptom that matches the problems your monitor has in the “SYSTEM — DIAG- NOSIS” subsection. The diagnosis telis the circuit or area the problem may be in and possibly even the actual component causing it.
- Once you have the circuit that is causing the trouble, read the “TROUBLESHOOTING” subsection to learn the procedure for finding the bad part.
- Next, go to the schematic section and find the schematic that matches your monitor. It may be helpful to read the “DIFFERENCES BETWEEN MONITORS” subsection if you are unsure of which monitor you have. Use the schematic to see what parts are in the offending circuit.
That really is all there is to it. Just remember that there are some bizarre or rare symptoms not covered, or that a monitor may have two or more different problems that only a genius, the experienced, or an experienced genius can figure out. But be patient, follow safety precautions, and remember that there is also literature available from the monitor companies through your distributor or from Midway Manufacturing Company on requesi. (There is a toll free number on the back side of the front cover of this manual.)
Symptom Diagnosis
. Insufficient width or heighth: A. Horizontal line (due to VERTICAL CIR- CUIT DEFECT). Bad yoke. Q Bad vertical output section. O Open fusible resistor in vertical section. O Bad height control. O Bad flyback. B. Vertical line (due to HORIZONTAL CIR- CUIT DEFECT). Bad yoke. © Open width coil. O Open part in horizontal output section. . Picture spread out too far or crushed in certain areas: A. Horizontal or vertical output transistor. B. Bad component in output circuitry. . Line too close with black spacing: A. Problem in vertical section causing poor linearity. . Poor focus and convergence: A. Bad high voltage transformer (‘‘flyback”) or control. B. Focus voltage wire not connected to neckboard terminal. . Colors missing; check: A. Interface color transistors. B. Color output transistors. Cc. Cracked printed circuit board. D. Color circuits. E. Video input jack. . Picture not bright enough: A. Weak emission from picture tube. (Turn horizontal sync off frequency and put brightness all the way up for about 15 minutes. Occasionally this cures the problem.) . Silvery effect in white areas; check: A, Beam current transistors. B. Weak picture tube emission. . Too much brightness with retrace lines; check: A. Beam limiter transistors. B. Brightness and/or color blanking control set too high. . Increasing brightness causes an increase in size and poor focus. A. Weak high voltage rectifier or regulation (high voltage unit). 10.
11.
12.
13.
14,
45.
16.
17.
18.
12, Small picture and/or poor focus: A. Low B+ voltage (power supply trouble).
Vertical rolling: A. Vertical oscillator transistor, IC, or circuit. B. No sync from logic board.
Horizontal line across center: A. Vertical output circuit is dead (see symptom No. 1. A). B. Vertical oscillator is not putting outthe right wave form, Picture bends: A. Horizonial sync needs adjusting. B. Magnetic or electromagnetic interference.
Flashing picture, visable retrace lines: A. Broken neck board. B. Internal short circuit in the picture tube (arcing). Unsymmetrical picture or sides of picture: A. Defective yoke.
No brightness, power supply operating — No high voltage for the picture tube; check: A. Horizontal oscillator. B. Horizontal amplifier and output. C. Flyback transformer (high voliage unit).
No brightness, high voltage present; check: A. Heater voltage to the tube at the neck board. B. Screen-grid voltage for the tube. C. Focus voltage. D. Grid to cathode picture tube bias.
No high voltage; check: For AC input to the “flyback”. Horizontal deflection stages. Flyback transformer. Yoke. Power supply. moo@g>
No horizontal and vertical hold; check: A. Sync transistors and circuit. B. Wires and jack from logic board to the monitor. Wavey picture — (power supply defect); check: A. Transistors, diodes, electrolytic capacitors in the power supply.
- Moving bars in picture: A. Ground connector off between monitor and logic boards. B. Defect in the power supply (see wavy picture symptom).
- Washed out picture (see picture not bright enough): A. Check video signal at the cathode pins with an oscilloscope. If there is about 80 volts peak to peak, the picture tube has weak emission.
23, Monitor won't turn on: A. Problem in the power supply: Check fuse, transistors, open fusible resistor,
B. Shorted horizontal output transistor. C. Defective high voltage disabling circuit. D. Crack(s) somewhere on main chassis board,
- Can't adjust purity or convergence: A. Use a degausser to demagnetize the picture tube carefully foliowing your degausser's instructions. B. Picture tube defective. C. Metal foreign material is in picture tube shieid. D. Nearby equipment is electromagnetically interferring. E. The poles of the earth are pulling off the purity. F. Poor focus or width of picture.
Guide To Schematic Symbols
THERMISTOR (POLARITY DOESN'T MATTER)
SY WH INDUCTOR, COIL, CHOKE (POLARITY DOESN'T MATTER)
(-) CATHODE
(+) ANODE
ZENER DIODE
8-3 lI I
IRON CORE TRANSFORMER (SUCH AS A FLYBACK)
VL
FUSE (POLARITY DOESN'T MATTER)
CATHODE (-)
ANODE (+)
DIODE
COLLECTOR Te COLLECTOR a BASE ———_* BASE————— EMITTER eg EMITTER mS
NPN TRANSISTOR PNP TRANSISTOR
f wn
VARIABLE RESISTOR, POT, CONTROL RESISTOR (POLARITY DOESN'T MATTER) (POLARITY DOESN’T MATTER)
+ :
LINES ARE CONNECTED ELECTROLYTIC CAPACITOR
LINES ARE NOT CONNECTED CAPACITOR (POLARITY DOESN'T MATTER)
tym = GROUND
Troubleshooting
Troubleshooting monitors requires experience, patience, and luck. The first step is to match the symptom the monitor displays to the diagnosis next to it in the “SYMPTOM-DIAGNOSIS” subsection. This will pinpoint the circuit the problem is probably in, and often the parts to check. Next, the circuit should be visually inspected to see if there are any parts broken, burned, or if something is there that shouldn't be, like a loose screw, etc. Some parts go bad before others and should be checked first. In fact, following is the general order in which parts usually go bad:
- Semiconductors (like transistors, diodes, and integrated circuits). Fusible resistors. Electrolytic capacitors. Resistors. Capacitors and coils. Always remember that a monitor can bite like a snake. Even when it is turned off, capacitors hold voltage and will discharge it to you should you be touching chassis ground. The picture tube or CRT, itself, is a giant capacitor, so avoid the flyback anode plug hole. With the monitor on, the power supply circuit and/or the flyback, which puts out at least 18,000 volts, CAN BE KILLERS!! Avoid handling power transistors (usually output transistors), yoke terminals, and other high power components when the monitor is on.
8-5 healthy charge for at least a week if not longer. Even after you've discharged it once, it may still carry a residual charge. It’s better to be too careful than dead, which is why electronic equipment always carries stickers referring servicing to qualified personnel. Handle the side with the viewing screen against your chest when changing it. ALWAYS wear safety goggles when handling the picture tube.
To maintain the safety and performance of the monitor, always use exact replacement parts. For instance, the wrong components in the power supply can cause a fire, or the wrong color transistor may give a funny color to the picture. Service your monitor on a nonconductive firm table like wood, NOT METAL, and take off all of your jewelry just in case. With all this in mind, you are ready to begin troubleshooting.
Observe the picture carefully. Try to vary the appropriate control that would most likely affect your particular symptom. For example, if there is poor brightness or no picture, try turning up the brightness or contrast control. If the controls have no effect at all, chances are there is trouble with the control itself, the circuit it controls, or a nearby circuit that may be upsetting voltages. Go to the list of symptoms and determine with the schematic where the bad circuit is.
Keep in mind that capacitors hoid a charge as can the picture tube (for at least a week and usually longer), and could shock you.
First, check for obvious visual defects such as broken or frayed wires, solder where it is not supposed to be, missing components, burned components, or cracked printed circuit boards. If everything looks good up to this point, make sure that diodes, electrolytic capacitors, and transistors have their leads connected in the right polarity as shown on the schematic and the circuit board. Turn on the power and measure the voltages at the leads of the active devices such as tubes, transistors, or integrated circuits. Any voltage that does not come within at least 10% to 15% of the voltage specified on the schematic indicates either a problem with that device or a component connected with it in the circuit. The next step is to use the ohmmeter to narrow down the field of possible offenders.
To test a transistor, one lead of the ohmmeter is placed on the base; and the other lead placed just on the emitter, then on the collector. A normal transistor will read either high resistance (infinite), or little resistance (400 to 900 ohms), depending on the polarity of this type transistor. Then the leads should be switched, one remaining on the base, and the other switched from the emitter to the collector. Now the opposite condition should result: the resistance should be infinite if it was lower when the other lead was on the base. Consistantly infinite readings indicate an open, and a short is demonstrated by 0-30 ohms on most of these test readings. Finally, place one lead on the collector, then the other on the emitter. No matter which lead is used, there should be infinite resistance. Any lower reading, such as 50 ohms (which is typical on a bad transistor), indicates a short. This all sounds pretty confusing, but a little experience on a good transistor will make you an expert in no time. Usually, the lowest ohmmeter setting is used for testing transistors. Once in a great while a transistor may check out good on this test, but may actually be “leaky” or break down only on higher voltages. If in doubt, change it. It is also wise to check the transistor out of the circuit just in case some component in the circuit is affecting the ohmmeter reading. A diode is tested like a transistor except it only has two leads. Again, there should be high resistance one way and little resistance the other. If it tests bad, take one lead out of the circuit in case some componentis messing up the ohmmeter reading.
Without special equipment, integrated circuits are checked by verifying the proper DC voltage on the pins and the correct AC wave form using an oscilliscope. BE CAREFUL: Shorting their pins can easily destroy them. Resistors are checked with an ohmeter and should usually be within ten percent of the value stated on them and on the schematic. You may have to desolder one lead from the printed circuit board. If you wreck the foil on the board, carefully solder a small wire over the break to reconnect the conductive foil. Capacitors are tricky. Their resistance goes up when checked with an ohmmeter which shows a charging action. As they suck up current from the meter, the voltage goes up and so does the resistance. If youare sure a particular circuit is giving you a problem and everything else checks out O.K., Electrolytic capacitors are prime suspects. Substitute a new one and keep your fingers crossed.
Theory of Operation
To understand what goes on inside the monitor, large general groups of circuits will be examined instead of laboriously analyzing the branches and small circuits that make up these groups. This will help avoid confusion and aid in a basic, concrete, knowledge of what makes up a monitor.
THE POWER SUPPLY — The AC going to the monitor from the game transformer is just like the voltage and current from your wall outlet. It jumps up and down going positive and negative sixty times a second. But a monitor needs nice, smooth DC; direct current, not alternating. So diodes chop up the AC and a big electrolytic capacitor filters it out to make it even smoother. Since the monitor is a big piece of electronic equipment, with many circuits demanding a lot of power from the power supply, there are also zener diodes and transistors to help maintain a nice, constant, smooth voltage so that the monitor circuits don’t jump around. And this is what happens when you see a wavy picture. There is AC creeping through the power supply, so it must be malfunctioning. If the voltage from the power supply is too low, the other circuits will be starved for power and you may see a small, wavy picture, or noneatall. Some circuits receive voitages that are higher than what the power supply should put out. But they come from the flyback transformer which will be discussed later. THE INTERFACE SECTION OF THE CHASSIS — The interface section of the chassis is fairly easy to identify. It is right by the place where the video jack(s) from the logic board(s) plug into. There are sets of transistors that receive the separate red, green, blue, and sync information from the cables that come from the logic boards. The circuits jack up the voltage and match impedances, or in other words, prepare the logic board outputs for the circuits that will really amplify them for the output devices such as the yoke in the case of the sync, or the picture tube that shows the colors.
An interesting aside is that our sync is composite negative sync. That means two things:
- The sync is a negative going wave form.
- There are two pulses going at different speeds over the same wire: a. Vertical wave forms at 60 times per second (or Hertz) and b. Horizontal wave forms at about 15,750 times per second (Hz). The sync is amplified by a sync amplifier transistor and sent on its way to the oscillators. The sync or timing information will be explained along with the oscillator shortly. The color information is sent via wires to the neck board where the main amplification occurs. This will also be discussed later.
VERTICAL AND HORIZONTAL DEFLECTION— After the sync signal is amplified by the sync amp, it goes to two different sections, the vertical and horizontal circuits. Basically, the sync signals are for timing so the picture doesn’t mess up since it is assembled like an orderly jigsaw puzzle, but so fast that you can’t see the electron beams for each color painting the picture on the screen. This will all become clear soon. For now, we will follow the 60 cycle component of the sync as it goes on its journey to the deflection yoke. The 60 cycle pulse goes to the vertical oscillator to make sure this circuit goes back and forth (or oscillates) at 60 times a second. Without this pulse keeping the circuit at the correct speed, it may get {azy and oscillate at 58 cycles or lower, or get ambitious and oscillate at 62 cycles or higher. At the wrong speed, the picture will start to roll up or down, A Wells Gardner 13” (K4806) or 19” (K4906, K4956) color monitor uses an integrated circuit for its sync section. An Electrohome 13” or 19” color monitor uses an integrated circuit !C501 for its sync section. Wells Gardner uses HA11423 and Electrohome uses HA11244, These ARE NOT interchangeable! The idea is all the same. The output to the vertical amplifying transistors for all monitors must form a sawtooth wave form, sort of like a bunch of pyramids, racing through the yoke’s vertical coils at 60 times a second. Along the way to the output transistors, the 60 cycle pulse is shaped and amplified to do the job: the yoke magnetically pushes the electron beam to fill the screen out sideways looking at the screen with the greatest length going up and down. Or viewing the screen sitting like a home television set, the amplified vertical output fills the screen up and down. Watching a monitor like this, seeing only a horizontal line means a problem with the vertical coils of the yoke or anything from the vertical output section on back to the oscillator.
8-7 The horizontal section is very similar with a few exceptions. The horizontal wave shape is more like a square and has a frequency of 15,750 cycles a second. Both Wells Gardner and Electrohome use the other side of their respective integrated circuits for the horizontal circuitry. If the oscillator isn't going at the correct speed, the picture may move sideways, start to slant, or tear up with slanted thin figures. With both the vertical and horizontal of all monitors, there are variable resistors that change the speed of the oscillators up and down. This way you have controls that can make the correct frequencies to keep the electronic jigsaw puzzle nicely locked in place. If you're driving in acarand next to you someone else is driving their car at exactly the same speed, it will appear that they are not moving. And this is why the sync frequency and the oscillator’s frequency must match, so the picture doesn't appear to move. The correct wave form is shaped and amplified in the circuitry just like in the vertical section. But the horizontal output transistor is a large power transistor and not only serves to give current to the horizontal yoke windings, it also feeds the flyback transformer.
THE FLYBACK TRANSFORMER (OR HIGH VOLTAGE UNIT) — The picture tube needs high voltage to light up, and the power supply can’t meet this demand. The flyback transformer receives current alternating at about 15,750 times per second from the horizontal output transistor. The “flyback” jacks up its input voltage and puts out a higher voltage alternating at the same speed. But, in your “flyback” there are diodes that chop up the alternating voltage to make it a smooth DC output just like in the power supply. This is what goes through that thick red wire to your picture tube. THIS AREA HAS ABOUT 18,000 VOLTS ON IT AND IT CAN KILL YOU! The “flyback” may be dangerous, but it is also generous. It has extra output windings which give voltage to the heater pins of the picture tube, voltage for the vertical deflection circuits, and picture tube screen-grid voltage. So in a way, the high voltage “flyback” is like a second power supply.
COLOR CIRCUITS — The color circuits are pretty straight forward. The signals go into the interface section where some amplification and impedance matching occurs. These circuits are pretty sparse and simple. Each color just has two transistors and a diode with some resistors and capacitors. From here, the AC color signal is sent by wires to the neck board. The color output circuits are on the neck board. The color signals going to the transistors are controlled by two variable resistors called drive controls. There are only two, one for the red and one for the green.
The blue doesn't have one. In the emitter part of each transistor is another variable resistor that is the cut off control. These controls vary the amount of amplified AC signal that goes to the cathodes of the picture tube. The more signal, the more color. The bases of each of these transistors are connected together and are all connected to the blanking and beam limiting transistors which are in the interface section. The beam limiter helps control the brightness level, and the blanking transistor rapidly turns the picture tube on and off so that retrace lines don’t show up on the screen. By turning up the brightness on a good monitor, these four to six retrace lines can be seen slanting diagonally across the picture.
PROTECTION CIRCUIT — To protect the high voltage section against voltages that are too high coming from the power supply which could cause X-rays to be emitted from the “flyback”, a circuit senses the higher power supply voltage, and using a transistor, turns off the horizontal oscillator. Since the horizontal oscillator doesn’t work, the horizontal output transistor has nothing to feed the “flyback” which in turn has nothing to feed the picture tube. The monitor will be silent, have no picture, and will appear to be off. But don’t be fooled. There is still that excessive amount of voltage coming from the power supply. To find out, check at pin two of Wells Gardner’s 1C501 and emitter of X04 for the Electrohome monitor. Here are the voltages you should receive: Weils Gardner = 130VDC Electrohome 120VDC The best place to measure this voltage on an Electrohome monitor is at a pin marked B1 on the chassis. This is because a 13 inch color Electrohome monitor, The GO7-FBO or GO7-902, has an integrated circuit and very little else in the power supply. Still, there should be 120VDC at B1.
THE PICTURE TUBE (OR CRT) — The picture tube or CRT is an output device. In other words, the end result of the circuit's work is displayed by this part. Actually, the output of other circuits is in the neck of the picture tube. First, there is the heater. The heater boils off electrons from the cathodes so that they (the electrons) shoot up to the screen to excite the phosphors so that the three phosphors emit three colors of light. The cathodes are next, and again they emit electrons to turn on the tube phosphors, making it glow. The cathode can arc or short to the heater resulting in no picture and a defective picture tube. Next come the grids. The first grid is grounded. The following grid is the screen grid which receives about 300VDC depending on the brightness setting. The next grid closest to the picture tube screen is the focus grid which gets about one fifth the amount of voltage that is applied to the picture tube anode. After jetting from the cathode through all these grids, the electrons speed through a mask, a sheet of material with tiny holes, and then excite the tiny dots of phosphor in the inside surface of the picture tube screen. The green electron gun (or cathode and circuitry) spits out electrons which head for the green phosphors only. The same goes for the red and blue guns. The way the phosphor light blends determines the color seen. Should these electron beams become too intense, they may burn the phosphor. With the monitor off, this can be seen as a dark permanent image of the video information on the tube screen.
Differences Between Monitors
The easiest way to identify the brand of monitor you are working with, assuming you can't find the brand name written on it anywhere, is to check the color of the suction cup type insulator that houses that dangerous anode plug on the CRT. Both monitors use a red wire but the Welis Gardner anode cup is BLACK while the Electrohome anode cup is LIGHT GRAY. Unfortunately, “call-out-numbers” for parts, circuit layout, and even circuit design are similar enough to confuse the average observer. Let's say you have an Electrohome that isn’t working. No problem. You can scavenge parts from an old broken up one that you may have around. Now let's say you have a Wells Gardner that isn't working. STOP! This could bea problem. There are3 different types of Wells Gardner K4900 SERIES monitors in the games. Here are ways to identify them. K4906 (1st TYPE) — This monitor's identifying tags have BLACK ink printed on a white background. There is NO Vertical Damping Control. (This Control would be next to the Vertical Hold Control but this area is jumpered with a small wire instead. K4906 (2nd TYPE) — This monitor's identifying tags have RED ink printed on a white background. There IS a Vertical Damping Control next to the Vertical Hold Control. The Damping Control provides a few more lines on the top of the monitor screen (monitor viewed as a normal T.V. would be) for any video game. that may need these lines to fit the picture on the
screen, Moving the Control may distort the top part of your picture (or the side, depending onthe game and how the monitor is mounted) so go ahead and move it if you are having this type of problem. To accommodate this new feature, there are a few circuit changes. ONE MAJOR DIFFERENCE BETWEEN THESE TWO VERSIONS OF THE K4906 IS THE YOKE. They look the same but notice the part numbers: K4906 WITHOUT the Damper Control: 2021111201 K4906 WITH the Damper Control: 2021111258 Since the companies like to change part numbers at the drop of a hat, the best thing to do is to request whatever part number is written on your yoke. If you should get the wrong yoke, the results will be: Picture distortion. Excessive brightness. Too much or too little vertical picture size. K4956 (3rd TYPE) — This monitor is identical to the K4906 WITHOUT tne Damper Control EXCEPT the picture tube is vertically mounted and there is an additiona! small P.C. Board mounted on the monitor where the yoke plugs in. This monitor is used on some Cocktail Table games where the picture has to flip for the second player. Generally speaking, some games flip the picture image via the logic board programming but this monitor is used in games that flip the picture image via generation of a smail signal voltage which is sent to the extra P.C. Board on this monitor. This signal voltage causes relays on this extra P.C. Soard to flip the picture by reversing the horizontal and vertical signals to the yoke pins. What kind of problems can this extra P.C. Board cause? If the relays become defective, the picture won't flip. If the P.C, Board gets cracked you may have a horizontal line on the screen, a vertical line on the screen, or maybe just a dot in the center of the screen, Of course, the logic board could be defective and not sending the signal to flip the picture. In any case, some people feel that using relays is cheaper, simpler, and more reliable, so this is an advantage.
CONTROLS YOU MAY NOT TOUCH Basically, on the Electrohome monitor, you can move any control you want EXCEPT for the B1 conirol. This sets the power supply voitage (ideally at 120 VDC) and is located right behind VERTICAL HOLD. The 13” Electrohome DOES NOT have this control. It may also be wise not to move the VERTICAL LIN- EARITY since this distorts the picture and is hard to reset perfectly. If you do move it, turn on the Cross Hatch Test Pattern of your game and try to get the squares to the point where they are equal in size by readjusting this Linearity Control.
On the Wells Gardner monitor, brightness is adjusted by the “BLACK LEVEL” Control which is right next to the Horizontal Frequency Control. Under the Focus Control is the “SCREEN” Control which youDO NOT touch. Yes, this control does adjust the brightness, butit is used to set the CRT bias and is adjusted at the factory. When Wells Gardner sets it, they mark the position with a black mark onthe knob. If you move it, be sure to realign the mark and THEN set the BLACK LEVEL Control to the brightness you desire. So, other than the SCREEN control, you may adjust any of the controls.
Parts Interchangeability
Some parts can be interchanged on all of the monitors. Here are the rules:
- You CAN swap any resistor between monitors that has the same resistance, wattage rating, and tolerance. You CAN swap any capacitor between monitors that has the same capacitance and voltage rating. You CAN swap many of the parts between the 19" and the 13” versions of each manufacturer's monitor. BUT, be certain to compare the manufacturers’ part numbers to be positive the parts you want to interchange are identical. BE SURE you have read the section DIFFERENCES BE- TWEEN MONITORS which was covered earlier. You CANNOT swap any picture tubes between monitors! In the past you could, but Wells Gardner is now using a new monitor. When
8-2 ordering a replacement picture tube, ALWAYS SPECIFY THE PICTURE TUBE NUMBER! You CANNOT change any part that is a safety part, one that is shaded in gray on the schematic; it MUST be IDENTICAL to the original. To do otherwise IS DANGEROUS. For instance, the 13 inch Electrohome (G07-902) monitor “flyback” looks identical to the 19 inch Electrohome (G07- 904) monitor “flyback”. In fact, there is even a 19 inch Electrohome (G07-905) monitor (which is an obsolete model) with a similar looking “flyback". NONE OF THESE ARE INTER- CHANGEABLE! You CAN change any of the parts between the G07-904 and G07-907. They're essentiaily the same monitor except that the G07-907 has a vertically mounted picture tube. lf there is any doubt about what parts can be swapped between each manufacturer's 19 inch and 13 inch models, compare the manufacturer's part number between each one. If they match up, they are the same part.
Power Supply Voltage and Symbols
Symbol Voltage Operating Circuit
15V Vert. Osc, Sync Blanking | CRT Cut-Off |
Horiz. Osc | Horz. Drive | Horz. Output | Vert. Output |
Video Output |
1VIDIV 200ust ECIOIV
TP.31 DC COUPLED INE =0 VDC. BOTTOM LI
2VIDIV 200MSECIDIV Le. 301, Pl INS
1VIDIV SMSECIDIV
TP-82
20VIDIV SMSECIDIV
LC. 301, PIN
1VDIV 200uSECIDIV Q351 COLLECTOR
20VIDIV 10uSECIDIV
1402-3
1VIDIV 20u SEC/DIV
1V/DIV 200uSECIDIV
NEGATIVE SIDE OF 0303
2V/DIV SMSECIDIV TP.31, AC COUPLED 19” COLOR MONITOR SCHEMATIC DIAGRAM
MODELS 19K4901, 19K4906, 19K4951, 19K4956
SERVICE TECHNICIAN WARNING X-RAY RADIATION PRECAUTION:
THIS PRODUCT CONTAINS CRITICAL ELECTRICAL AND MECHANICAL PARTS ESSENTIAL FOR X-RAY RADIATION LE DEGRE DE SECURITE DE L’
PROTECTION FOR REPLACEMENT PURPOSES, USE ONLY TYPE PARTS SHOWN IN THE
PARTS LIST DONT LE FONCTIONNEM
FABRICANT.
CRITIQUE POUR LA SECURITE QUE PAR DES PIECES RECOMMANDEES PAR LE ENT EST
2401 RED OUT 28C2068.8/L98K 25CZ068I.8/ 85K 2SC20861 8/1 89K OSCILLOSCOPE WAVEFORM PATTERN The waveforms shown are as observed on the wide band oscilloscope with the monitor turned to a reasonably strong signa! and a norrnal picture. The voltages shown on each waveform are the approximate peak amplitudes. If the waveforms are observed on the oscilloscope with @ poor high frequency response, the corner of the pulses will tend to be more rounded than those shown and the amplitude of any high frequency pulse will tend to be less.
aie bur
2SCISI4BVC/CVC 2SCISI4BVCVC 28CISI4BVC/CVC
tT
| | | a | : | te 205% | ait | he |
| 0.5/DIV SMSEGIDIV | BSCIBIEY/SR | io | 10 | fi | |
| ested | Mate. | R2I7 | baaie |
= Es 0209" ha” BY/0 — eSCI@ISY/ en
SYNC. AMP 2scisisy, O.SIDIV 20u SECIDIV
LC. 301, PIN 15 A388 He = oBKmSPS) oeaae Br10K N30 soy Wikevas ST CN) eSB 6I0BK | Bitsy
| may | Ohne | 360 | ! | |
| a: | ws) | 3 | ea | 3 |
ren re OP gre) HOR.OUT 280800 2608968
i SG” dates STOFF] [G.CUTOFF]
1e301 SYNC AMP vosc H.08C HaIIa23
19906 i 7886 cibay Ee) icwar
1VDIV 2MSECIDIV DEGAUEEING COIL, T ae
ts
2878 Teisss | aos mcur (HOR ssa
DEFLYOKE
K4901D, K4906D, K49510 5833 K4956B 8-10 :
REPLACEMENT PARTS LIST This monitor contains circuits and components included specifically for safety purposes. For continued protection no changes should be made to the original design, and components shown in shaded areas of schematic, or A * on parts list should be replaced with exact factory replacement parts. The use of substitute parts may create a shock, fire, radiation or other hazard. Service should be pertormed by qualified personnel only.
MAIN BOARD
| Ref. No. | Part No. | Description | Ref. No. | Part No. | Description: |
RESISTORS RESISTORS (CONT)
| 203X6500-645 | 4K Ohm, 5%, 1/4W Carbon | R369 | 203X5802-329 | 680K Chm, 5%, 1/2W Comp. | |
| 203X6500-523 | 30 Ohm, 5%, | 1/4W Carbon | R370 | 203x6501-002 | 33K Ohm, 5%, 1/4W Carbon |
| 203X6500-405 | 100 Ohm, 5%, 1/4W Carbon | 371 | 203X9014-584 | 1K Ohm, 5%, 1W Metal Oxide | |
| 203x8700-327 | 100 Ohm, 5%, 1/2W Carbon | R372 | 203K9101-119 | 12K Ohm, 5%, 1W Metal Oxide | |
| 203X6700-421 | 270 Ohm, 5%, 12W Carbon | R375 | 203X6700-763 | 6.8K Ohm, 5%, 1/2W Carbon | |
| 203X6500-540 | 390 Ohm, 5%, | 1/4W Carbon | R376 | 203X9104-404 | 270 Ohm, 5%, 2W Metal Oxide |
| 340X2201.834 | 200 Ohm, 5%, | 1/4W Carbon | R377 | 203X6500-447 | 150 Ohm. 5%, 1/AW Carbon |
| 203X6500-540 | 390 Ohm, 5%, 1/4W Carbon | R378 | 203X6500-886 | 10K Ohm, 5%, 1/AWW Carbon | |
| 340X2201-934 | 200 Ohm, 5%, 1/4W Carbon | R379 | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | |
| 203x6500-540 | 390 Ohm, 5%, t4W Carbon | R380 | 203X6500-865 | 8.2K Ohm, 5%. 1/4W Carbon | |
| 240X2201-934 | 200 Ohm, 5%, 1/4W Carbon | R381 | 203X6500-724 | 2.2K Ohm, 5%, 1W Metal Oxide | |
| 203X6500-645 | 1K Ohm, 5%, 1/4W Carbon | R383 | 203X9014-387 | 150 Ohm, 5%, 1W Metal Oxide | |
| 203X6501-126 | 100K Ohm, 5%, 1/4W Carbon | R502 | 203X6500-866 | 10K Ohm, 5%, 1/4W Carbon | |
| 203X6500-645, | 1K Ohm, 5%, W4W Carbon | R503 | 204X 1700-535 | 150 Ohm, 5%, 15W Metal Oxide | |
| 203X6500-405 | 100 Ohm, 5%, 1/4W Carbon | R504 | 203X9014-267 | 47 Ohm, 5%, 1W Metal Oxide | |
| 203X6500645 | 4K Ohm, 5%, 1/4W Carbon | R505 | 203X6501-209 | 2.2K Ohm, 5%, V4W Carbon | |
| 203x6501-126 | 100K Ohm, 5%, 1/4W Carbon | R506 | 203X9104-105, | 15 Ohm, 5%, 2W Metal Oxide | |
| 203X8500-645, | 1K Ohm, 5%, 1/4W Carbon | R507 | 203X5602-185, | 330K Ohm, 5%, 1/2W Comp. | |
| 203X6500-405 | 100 Ohm, 5%, 1/4W Carbon | ARE | 204X1625-058 | 3.3 Ohm, 5%, 10W WW | |
| 203X6500-762, | 3.3 Ohm, 5%, 1/4W Carbon | R701 | 203X9105-141 | 2.2 Ohm, 5%, 2W Metal Oxide | |
| 203X6500-169, | 10 Ohm, 5%, 1/4W Carbon | R702 | 203X6206-441 | 2.2 Ohm, 5%, 1/2W Carbon | |
| 203X6500-169 | 10 Ohm, 5%, 1/4W Garbon | R201 | 204X2070-072 | 2K Ohm-B Semi-Fixed | |
| 203X6500-163 | 10 Onm, 5%, 1/4W Carbon | R301 | 204X2070-084 | 5K Ohm-8 Semi-Fixed | |
| 203X6301-044 | 47K Ohm, 5%, 1/4W Carbon | R303 | 204X2070.058 | 500 Ohm-B Semi-Fixed | |
| 203X6500-645 | 1k Ohm, 5%, 1/4W Carbon | VR351 | 204X2070.072 | 2K Ohm-B Semi-Fixed | |
| 203X6700-421 | 270 Ohm, 8%, 1/2W Carbon | R352 | 204x2070-072 | 2K Ohm-B Semi-Fixed |
203X6500-863, 8.2K Ohm, 5%, 1/2W Comp. 203X8500-863 8.2K Ohm, 5%. 1/2W Comp. 203X6500-863 8.2K Onm, 5%, 1/2W Comp.
| 203X6500-468 | 480 Ohm, | 5%, 1/4W Carbon |
340X2820-234 82 Ohm, 5%, 1/4W Carbon CAPACITORS
| 340X2820.934 | 82 Ohm, 5%, 1/4W Carbon | 0201 | 203X0014.088 | 1000 uF, 16V, Electrolytic | |
| 340X2820-934 | 82 Ohm, 5%, \/4W Carbon | C202 | 202X7200-064 | 330 pF, 500V. Ceramic | |
| 203X6500-508 | 270 Ohm,5%, 1/4W Carbon | C203 | 202X7200-043 | 220 pF, 500V, Ceramic | |
| 203X6500-863 | 8.2K Ohm. 5%, 1/4W Carbon | C204 | 202X7200-043 | 220 pF, 500V, Ceramic | |
| 203X6500-863 | 8.2k Ohm, 5%, 1/4W Carbon | C205 | 203x0014-076 | 470 uF, 16V, Electrolytic | |
| 203X6500-724 | 2.2K Ohm, 5%, 1/4W Carbon | C208 | 203X 1810-149 | 0.1 uF, 125V Mylar | |
| 203X6500-842 | 6.8K Chm, 5%, 1/4W Carbon | C207 | 349%2232-109 | .022 uF, 100V Mylar | |
| 203X6003-201 | 7.5K Ohm, 2%, 1/4W Carbon | C301 | 203X0014-065 | 330 uF, 5OV Electrolytic | |
| 203X6500825 | 5.6K Ohm, 5%, 1/4W Carbon | 302 | 203X1600-563 | 0.033 uF, 50V Mylar | |
| 203X6500-965, | 22k Om, 5%, 1/4W Carbon | 303 | 203X0629-037 | 3.3 uF, SOV Electrolytic | |
| 203X6500-988 | 39K Ohm, 5%, 1/4W Carbon | C304 | 203X1600-366 | 0.068 pF, 50V Mylar | |
| 203X6500-762 | 3.3K Ohm, 5%, 1/4W Carbon | C306 | 203X0412-012 | 2.2 uF, 16V Tantal | |
| 203x9014-741 | 4.7K Ohm, | 5%, 1/4W Carbon | 6307 | 203X1600-634 | 0.033 uF, 50V Mylar |
| 2041450537 | 1K Ohm, 5%, 5W Carbon | C308 | 203X0025-174 | 3.3 uF, 50V Electrolytic | |
| 203X6500-481 | 220 Ohm, 5%, 1/4W Carbon | C309 | 203x1207-100 | 0.068 uF, 100V PP. | |
| 203X6500-168 | 10 Ohm, 5%, 1/4W Carbon | caro | 203X0629-061 | 10 uF, 100V Electrolytic | |
| 203X6500-762 | 3.3K Ohm, 5%, 1/4W Carbon | c3it | 203X004 1.028 | 10 uF, 160V Electrolytic | |
| 203X6700-107 | 42 Ohm, 5%, 1/2W Carbon | 312 | 202X7050-248 | 1000 pF, 500V Ceramic | |
| 203X6500.540 | 390 Ohm, 5%, 1/4W Carbon | 6313 | 203X0040-052 | 47 uF, 160V Electrolytic | |
| 203X6500-645 | 1K Ohm, 5%, 1/4W Garbon | 314 | 203X 1201-265 | 0.033 uF, 200V PP | |
| 203X650 1-002 | 33K Ohm, 5%, 1/4W Carbon | C315 | 203X0629-023 | 1 uF, SOV Electrolytic | |
| 203X6501-224 | 270K Ohm, 5%, 1/2W Carbon | 351 | 203X0629-023 | 1 uF, 50V Electrolytic | |
| 203X6500-886 | 40k Ohm, 5%, t/4W Carbon | 352 | 203X0619-045 | 47 uF, 25V Electrolytic | |
| 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | C353 | 203X1 190-015 | 0.0082 pF, 50V Mylar-PP | |
| 203X6500-785 | 3.9K Ohm, 5%, 1/4W Carbon | 6354 | 203X0619-045 | 47 uF, 25V Electrolytic | |
| 203X6501-088 | 68K Ohm, 5%, | 1/4W Carbon | C355 | 203X1600-366 | 0.0058 pF, 50V Mylar |
| 203X6500-762 | 3.3K Ohm, 5%, 1/4W Carbon | 0356 | 202X7050-483 | 0.01 uF, 500V Ceramic | |
| 203X9205-143 | 68K Ohm, 5%, 3W Metai Oxide | C359 | 202X8085-608 | 100 pF, 500V Ceramic | |
| 203X5601-878 | 56K Ohm, 5%, 1/2W Carbon | 360 | 202X7050-366 | 0.0033 pF, 500V Ceramic | |
| 203X6500-561 | 470 Ohm, 5%, 1/4W Carbon | 0361 | 202X7050-483, | 0.01 uF, 500V Ceramic | |
| 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | C362 | 202X7203-032 | 0.01 uF, 50V Ceramic | |
| 203X9014-645, | 1.8K Ohm, 5%, 1W Metal Oxide | #0363 | 203X1270-911 | 8700 pF, 1.5 KV PP | |
| 204X1527-751 | 3.9K Ohm, 5%, 7W Metal Oxide | #0365 | 203X1201-265 | 0.33 uF, 200V PP | |
| 203X8500-246 | 22 Ohm, 5%, 1/4W Carbon | C366 | 203X0019-026 | 22 uF, 25Y Electrolytic | |
| 203X6501-002 | 33K Ohm, 5%, 1/4W Carbon | C367 | 202X8065-162 | 6 pF, 500V Ceramic | |
| 203X6500-886 | 10K Onm, 5%, 1/4W Carbon | 368 | 202X7203-032 | 0.01 uF, 50V Ceramic | |
| 203X5602-185 | 330K Ohm, 5%, 1/2W Comp. | C372 | 203X 1207-125 | 0.1 uF. 100V PP |
MAIN BOARD (CONT)
| Rof. No. | Part No. | Description | Ref. No. | Part No. | Description |
CAPACITORS (CONT.) SEMICONDUCTORS (CONT.)
| 6380 | 202X7200.087 | 470 uF, S00V Ceramic | 206 | 200X3181-523 | Transistor (NPN) 2SC1818GR |
| ‘4. C501 | 203K 1810-149 | 0.1 uF, 128V Mylar | 207 | 200x3181-523 | Transistor (NPN) 2SC1815GR |
| 4 ¢502 | 202X7080.282 | 1500 pF, S00V Cerartic | 208 | 200x3181-523 | Transistor (NPN) 2SC1815GR |
| 4 C503 | 202x7810.214 | 2200 pF, 125V Ceramic | 208 | 200x3181-523 | Tranalstor (NPN) 2SC1851GR |
| 4.c504 | 202X7810.214 | 2200 pF, 125V Ceramic | 210 | 200X3181-523 | Transistor (NPN) 2SC1851GR |
| 6505, | 203X0220-075 | 560 uF, 200V Electrolytic | 301 | 200X3181-523 | Transistor (NPN) 2SC1851GR |
| 508 | 203X0040-034 | 22 uF, 160V Electrolytic | 302 | 200X3207-306 | Transistor (NPN) 2802073LBGL2 |
| 507 | 203X0041-057 | 47 UF, 160V Electrclytic | 303 | 200X3207-308 | Transistor (NPN) 2802073LBGL2 |
| ¢701 | 208x0019-092 | 1000 uF, 25V Electrolytic | 9361 | 200X3248-217 | Transistor (NPN) 28624828 |
| Gro2 | 203X0634-061 | 10 uF, 100V Electrolytic | Q3s2 | 200X4589-802 | Transistor (NPN) 2SD898B |
| 703 | 202X7050-248, | 1000 pF, 500V Ceramic | nt | 200X2300-033, | IG HA11423 |
| Ak | 16501 | 200X2600-183, | Ic STR381 |
SEMICONDUCTORS
| 203 | 201X2010-159 | Diode, 1$2076-27 | |||
| D208 | 201X2010-159 | Diode, 1$2076-27 | TRANSFORMERS & COILS | ||
| D205 | 201X2010-189 | Diode, 1$2076-27 | (361 | 201X4710-134 | Coll, (RF Choke) |
| D206 | 201X2010-159 | Diode, 1$2076-27 | L352 | 201X5000-083 | Coll, Horiz. Size |
| 0207 | 201X2010-159 | Diode, 1$2076-27 | L701 | 611X0004-007 | Coll, Adg, |
| D208 | 301x2010159 | Diode, ($2076.27 | 1361 | 202X 1300-080 | Transtormer, Hor. Drive |
| 2209 | 201X2040-189 | Diode: 1S2078.27 | Aw 1352 | 200X9720-301 | HV-Unit M11 |
| D301 | 201X2010-165 | Diode, IS$81 | |||
| D302 | 201X2010-159, | Diode, 182076.27 | MISCELLANEOUS | ||
| 0303 | 201X2010-159, | Diode, 182076.27 | F501 | 204X7120-073 | Fuse, 4 Amp. 125V |
| D304 | 201X2120.009 | Diode, RH:IV | 402 | 206X5008632 | Recep W Wire 3P-M-BG |
| D305 | 201X2120.009 | Diode, RH:IV | 201 | 204X9600-466 | Plug, PWB 3P-J |
| D308 | 201X2010-159, | Diode, 1$2076-27 | P202 | 204X9601-477 | Plug, PWB 6P-Q |
| D501 | 201X3120-216 | Diode, RM-1AV | 401 | 204X9600-298 | Plug, PWB 4P-3 |
| 0502 | 201X3120.216 | Diode, RM-1AV | 501 | 204x9600-249 | Plug, PWB 2P-B |
| 4.0503 | 201X3120.216 | Diode, RM-1AV | 601 | 204X9600-304 | Plug, PWB 4P.C |
| 0504 | 201X3120.216 | Diode, RM-1AV | THS01 | 201X0100-112 | Thermistor |
| D505 | 201X3120-216 | Diode, RM-1AV | |||
| 508 | 201%3120-216 | Diode, RM-1AV | |||
| 0701 | 201x2190.294 | Diode, AU-2V | FINAL ASSEMBLY PARTS | ||
| D702 | 201X2120-009 | Diode, RH-1V | A 88X0198-508 | 19VLTP22 Pix Tube | |
| 201 | 200X3181-523 | Transistor (NPN) 2SC1815GR | 205X9800-158 | Lateral/Purity Assembly | |
| 202 | 200X3181-523 | Transistor (NPN) 2SC1815GR | Ae 202X1111-201 | Yoke Deflection | |
| 2203 | 200X4056-260 | Transistor (PNP) 25A562-Y-TM | 204X9301-255 | CRT Socket | |
| 208 | 200X4056-260 | Transistor (PNP) 25A562-Y-TM | 291X8004.262 | Automatic Degaussing Coil Unit | |
| 0205 | 200X4056-260 | Transistor (PNP) 25A562-Y-TM |
NECK BOARD RESISTORS CAPACITORS
| R401 | 203x6000-728 | 220 Ohm, 5% 1/4W Carbon | 401 | 202X7050-269 | 4200 pF, 500V Ceramic |
| R402 | 203X6500-540 | 390 Ohm, 5% 1/4W Carbon | C402 | 202X7050-248 | 1000 pF, 500V Ceramic |
| R403 | 203X6000-661 | 820 Ohm, 5% 1/4W Carbon | C403 | 202X7050-248 | 1000 pF, 500V Ceramic |
| Raa | 203x6000-728 | 220 Ohm, 5% 1/4W Carbon | 0404 | 202X7050-282 | 1500 pF, 1.8KV Ceramic |
| R405, | 203x6500-540 | 390 Ohm, 5% 1/4W Carbon | C408 | 202X7050-483 | 0.01 uF, 500V Ceramic |
| R406 | 203X6000-661 | 820 Ohm, 5% | 1/4W Carbon | ||
| R407 | 203x6000-729 | 470 Ohm, 5% 1/4W Carbon | |||
| R408 | 203X6000-998 | 270 Ohm, 5% 1/4W Carbon | SEMICONDUCTORS | ||
| R409 | 203X6000-661 | 820 Ohm, 5% 1/4W Carbon | |||
| : | 401 | 200X3206-800 | Transistor (NPN) 2802068LB | ||
| Rato | 203x9104-824 | 15K Ohm, 8% 2W M.O. Forming | aao2 | 200X3206-800 | Transistor (NPN) 28C2088LB |
| Ratt | 203X9104-824 | 19K Ohm, 5% 2W M.0. Forming | 403 | 200X3206-800 | Transistor (NPN) 28C2068LB |
| Ra12 | 203X9104-824 | 15K Ohm, 5% 2W M.O. Forming | |||
| Ra13 | 203x6000-998 | 2.7K Ohm, 8% 1/2W Comp. | |||
| Rata | 203X6000-998 | 2.7K Ohm, 8% 1/2W Comp. | |||
| Rats | 203X6000-998 | 2.7K Onm, 8% 1/2W Comp. | MISCELLANEOUS | ||
| Rate | 203X9105-154 | 2.2 Ohm, 8% 2W Metal Oxide | py | 206%5009-296 | Led ea |
| Ra19 | 203X6500-741 | 2.7K Ohm, 5% 1/4W Carbon | Paog | 204X9600-254 | Plug, PWB 3P-A |
| R420 | 203X6500-741 | 2.7K Ohm, 5% 1/4W Carbon | Pans | Boaxoeon 951 | Plug, Pin 1P-D |
| oe, | P701 | 204x9601.020 | Plug, | PWB 4P-E | |
| Ra21 | 203X6500-744 | 2.7K Ohm, 5% 1/4W Carbon | 9, | ||
| vRao1 | 204x2115.014 | 500 Ohm, B Semi |
vRao2 204X2115-014 R403 204X2115-006 VR404 204X2115-006
| VR405 | 204X2115.006 | 5K Ohm, -B Semi-Fixed |
Mioi=xi08 RGB ViseO OUTPUT 2SC26!! or 28cisi4¥ Sat vas
‘Sync AMP | { 1301x302 %308,x308
| aus meen ven seme QP | Bat
rome
X304 BLANKING 28C494C oF 26c/68S
X90 POWER DRIVE 25C 2686 ae X902 ERROR AMP 7SC1890 | “sea ——————_———— tos,
4.
5a wow oo r a =e in)
xsor_obtiae
Schematic Notes Unless otherwise specified ES Tecor Resistance: (Q.) (K->KQ, M--MQ), 1/4 (W) carbon resistor + i Capacitance: 1 or higher-> (pF), less than 1 (yF) wr BPe ve working voltage -» 50 (V) wena ceramic capacitor pana L Inductance: (v H) | OxOT rion voKE Electrolytic Cap: Capacitance Value (» F)/working voltage (V), Move | | Ritts ooo NP — non-polar (or bipolar) electrolytic cap. em | | | on Refer to the parts list for additional component information. ————— aa oo — > Q indicates test point connection X701 X-RAY PROTECTOR 1H v ve su-soree Vue nr weaver . . 28C454C or asciees BESOPRE, ascosm eae .. ¥ hy indicates chassis ground unless otherwise specified 2svezo acizov cors/soKe Hz _ indicates cycles per second “em For satety purposes (and continuing reliability) a replace all components marked with safety syrnbol with identical type.
00-4147-04 Parts identification on circuit boards: G07-CBO e.g. SU1126A (R107 = R1107) SU3030A (R113 = R3113)
REPLACEMENT PARTS LIST - ELECTROHOME 19” MONITOR '
Components identified by the 4, symbol in the PARTS LIST and on the Schematic have special characteristics important to safety. DO NOT degrade the safety of the set through improper servicing.
Abbreviations for Resistors and Capacitors
Resistor Capacitor
| CR | : Carbon Resistor | C Cap. |
| Comp. R | : Composition Resistor | M Cap |
| OMR | : Oxide Metal Film Resistor | E Cap. |
| VR | : Variable Resistor | BP E Cap. |
MF R : Metal Film Resistor
| CMF R | : Coating Metal Film Resistor | MM Cap. |
| UNF R | : Nonflammable Resistor | PP Cap. |
| FR | : Fusible Resistor | MPP Cap. |
PS Cap Tan. Cap. : Ceramic Capacitor Mylar Capacitor Electrolytic Capacitor Bi-Polar (or Non-Polar) Electrolytic Capacitor : Metalized Mylar Capacitor Polypropylene Capacitor : Metalized PP Capacitor Polystyrol Capacitor : Tantal Capacitor
SERVICE REPLACEMENT PARTS LIST
Symbol Description
Main P.C.B. Ass'y CRT Socket P.C.B. Ass'y Purity Shield Ass'y
8-14 Part Number SU-1133A SU-3032A 07-220083-03
Outside of the P.C.B, Ass'y Symbol Description Picture Tube 19” A AXDeflection Yoke PC Magnet A AsFlyback Transf. A AHVAR ROS UNF Resistor 2200,25W K C04 C Capacitor 150pF, AC1.5KV X01 Si. Transistor x02 Si. Transistor Sc Screw #8-¥, sc Screw % x % Pix Tube Mtg. (4) WA Pyramidal Lock Washer (4) Nut Retainer, Pix Tube Mtg. (4) Clip — P.C.B. Support Standoff Wire Terminal (Gnd. Strap) Terminal Lug (Gnd.) Groundstrap Assy. Grounding Spring Wire Hook (Gnd. Strap) Purity Shield Holddown Clamp Support Brkt. RH Support Brkt. LH Chassis Base Yoke Wedge (3)
Purity Shield Ass’y. Parts List
Symbo! Description Degaussing Coil D911, D912 Rectifier 1 Amp 600V (2) Pin Terminal (2) Pin Terminal Housing Purity Shield (2 pes.) Purity Shield (2 pes.) coi Capacitor 100nF 10% 400V Re21 Resistor, Wirewound 332, 4W Fire Retardent Term. Strip 4 Lug
CRT Socket P.C.B. Ass’y (SU-3032A) Parts List
Resistors Symbol Description
| R3105 | v | R 200 |
| R3106 | v | R 200 |
| R3113 | Vv | R 5K |
| R3114 | Vv | R 5K |
| R3115 | Vv | R 5K |
| R3116 | OM | R 10KQ2W J |
| R3117 | OM | R 10KQ2W J |
| R3118 | OM | R 10KQ2W J |
R3119 Comp. R 3.3KQ%W K R3120 Comp. R 3.3KQ%“4W K 3121 Comp. R 3.3KQ%W K
Capacitors Symbol Description C3107 E Cap. 10uF 250V A C3108 C Cap. 1000pF DC1400v P
Coils Symbol Description L3101 Peaking Coil Part Number 17-7198-03 A29779-D = 21-141-01 A75034-B = 29-32-01 A29951-B A46600-A QRF258K-221 QCZ0101-005 2SD870 2SC1106A 31-610818-06 31-601418-12 33-255-01 33-494-01 33-629-02 33-670-010R-02 34-228-03 34-33-04 34-574-02 35-212-03 35-3053-02 35-2348-01 35-3890-01 35-3890-02 38-449-02 39-1233-01
Part Number 21-1007-30 28-22-27 34-708-01 34-709-01 35-3847-01 35-3847-02 48-171544-62 42-113301-03 34-492-09
Part.Number QVZ3234-022 QVZ3234-022 QVZ3234-053 QVZ3234-053 QVZ3234-053 QRG029J-103 QRG029J-103 QRG029J-103 QRZ0039-332 QRZ0039-332 QRZ0039-332
Part Number QEWS3EA-106 QCZ9001-102M
Part Number QQL043K-101
Semiconductors Symbol X3101 X3102 X3103
Miscellaneous Symbol A Description Si. Transistor Si. Transistor Si. Transistor
Description ASCRT Socket
Main PCB Ass’y (SU-1133A) Parts List
Resistors Symbol R1406 R1408 R1410 R1414 R1415 R1421 R1422 AFR1401 AR1503 R1504 R1509 R1512 R1514 R1515, R1522 R1523 R1528 R1534 VR1501 AR1703 AR1704 AR1901 R1902 R1903 R1904 R1905 4AQ1908 AMR1909 R1910 ASFR1901
Capacitors Symbol C1301 C1402 C1407 c1411 C1412 C1508 AC1512 401513 4c1514 C1515 C1520 C1523 C1524 401531 AC1532 1904 C1905 Description Vv R 2002 v R 2009 CMF R 6821WJ OM = R 3.3KQ1WJ OM R 27KQiW J OM R 12KQ2W J v R 10KQ2 AF R 6822W K ACMF RR 11.8KQ. YW 41% v R 5K OM R 10K22W J OM FP B2KQ2WJ OM A 820022W J CMF R 8221WJ CMF R 47Q1WJ OM R 6822W J OM = R 39021Wu ZN R ZN R ACMF R_ 392.,W +1% ACMF R7.68KQ. UW +1% AsPosistor UNF R 2Q7WK CMF R 47923WJ OM =R_ 10KQ2W J OM R 18KQIW J ACMF RR 470.°%4W +1% v R 2kQ ACMF R 2.74KQUW+1% AF R 2202%4W K
Description BPE Cap. 3.3uF 50V A Tan Cap. 2.2uF 16V K E Cap. 4.7uF 6.3V A E Cap. 100uF 160V A £ Cap. 3.3uF 160V A PP Cap. 5600uF SOV J APP Cap. 2000pF DC1500V J APP Cap. 2000pF DC1500V J A\PP Cap. 2000pF DC1500V J PP Cap. 0.5duF DC1200V J BPE Cap, 3.3uF 50V A E Cap. 1uF 160V A M_— Cap. 0.1uF 200V K ANPP Cap. 2000pF DC1500V J APP Cap. 1500pF DC1500V J E Cap. E Cap. 10uF 250VA Part Number 2SC1514VC 2SC1514VC 2SC1514VC
Part Number A76068
Part Number QVZ3230-002 QVZ3230-002 QRX019J-6R8 QRGO19J-332 QRGO019J-272 QRG026J-123Z, QVZ3230-014 QRH024K-680M QRV142F-1182 QVZ3230-053 QRG026J-103Z QRG026J-822Z QRG026J-821Z QRX019J-8R2 QRX019J-4R7 QRG026J-680Z QRG019J-391 ERZ-CO5ZK471 ERZ-COSDK271 QRV122F-3902 QRV142F-7681 A75414 QRFO76K-2RO QRX039J-4R7 QRGO026J-103Z QRG019J-183 QRV122F-470Z QVPSAO0B-023E QRV142F-2741 QRH124K-221M
Part Number QEN61HA-335Z QEES1CK-225B QEWS51JA-475 QEWS52CA-107 QEWS2CA-335 QFP31HJ-562 QFZ0082-202 QFZ0082-202 QFZ0082-202 QFZ0067-534 QEN61HA-335Z QEW62CA-105Z QFM720K-104M QFZ0082-202 QFZ0082-152 QEY0034-001 QEWS52EA-106
Coils Symbol 11502 11503 11504
Transformers Symbol T1501 T1503
Semiconductors Symbol 101501
X1101 X1102 X1103 X1104 X1105 X1106 X1301 X1302 X1303 X1304 X1305 X1401 X1402 X1501 X1901 X1902
D1101 01102 01103 D1301 01401 D1402
D1503 D1504 D1505 D1506 D1507 D1508 Ap1701 ADi901 A\D1902 A\D1903 AxD1904 AXD1905
Miscellaneous Symbol AF1901 A\F1902 Description Linarity Coil Width Coil Heater Choke
Description Hor. Drive Transf. Side Pin Transf.
Description Ic
i. Transistor i. Transistor i. Transistor i. Transistor i. Transistor i, Transistor i. Transistor i. Transistor i. Transistor |. Transistor i. Transistor . Transistor i. Transistor i. Transistor i. Transistor i. Transistor
i. Diode i. Diode i. Diode i. Diode i. Diode Zener Diode
Si. Diode Si. Diode Zener Diode Si. Diode Si. Diode Si. Diode A\Zener Diode ASi, Diode ASi. Diode ASi. Diode ASi. Diode AsZener Diode
Description AFuse 1.25A ANUL Fuse 3A Part Number A39835 C30380-A C30445-A
Part Number A46022-BM 39050-A,
Part Number HA11244
2SC1685(R) 28A673(C) 2SC1685(R) 2SA673(C) 2SC1685(R) 28A673(C) 28C1685(R) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SC1685(R) 28D478 2SD478 28C2610BK 28C2688 (K.L.M.) (EF.)
WO6A 18Z473H 18Z473H RD10F(C) HF-1 VO9E RD11E(B) WO6A 18881 18Z473H RD20EV2 181887A 1S1887A 181887A 181887A RD6.8EV3
Part Number QMF53U1-1R25S QMF66U1-3ROS
{= 101 POWER REGULATOR
- SU-I103A MAIN PCB ASSY X303 BEAM LIMITER 254673 TSE Pigo4 acawwns ee | ascasac mth G7 X1OV. IGS and XIOS VIDEO AMP 25C454C o, 25¢1609 X102,X104 ond Xi06 VIOEO_AMP. 2SA673C ee i ad aah ‘x103 RB VIDEO OUTPUT ore a8cael! er #8cis18V
M8 \su-so16a | lear socket PCB ASSY _ |
et AciZov 60H:/S0Hz % Shao Fe
Pons i x40), xa02) [2ssare
X701 X-RAY PROTECTOR 2SC434C or 25C 685
G07-FBO
00-4147-03 Schematic Notes Unless otherwise specified Resistance: ((2) (K->KQ, MM), 1/4 (W) carbon resistor Capacitance: 1 or higher— (pF), less than 1 (yF) working voltage-» 50 (V) ceramic capacitor Inductance: (v H) Electrolytic Cap: Capacitance Value (y F)/working voltage (V), NP — non-polar (or bipolar) electrolytic cap. Refer to the parts list for additional component information. 2 indicates test point connection ah indicates chassis ground unless otherwise specified Hz _ indicates cycles per second For safety purposes (and continuing reliability) Aa replace all components marked with safety symbol with identical type.
Parts identification on circuit boards: e.g. SU1126A (R107 = R1107) SU3030A (R113 = R3113)
REPLACEMENT PARTS LIST - ELECTROHOME 13”’ MONITOR
Components identified by the 4\ symbo! in the PARTS LIST and on the Schematic have special characteristics important to safety. 00 NOT degrade the safety of the set through improper servicing. J
Abbreviations for Resistors and Capacitors
Resistor Capacitor
| CR | : Carbon Resistor | Cc Cap. |
| Comp. R | : Composition Resistor | M Cap |
| OMR | : Oxide Metal Film Resistor | & Cap. |
| VR | : Variable Resistor | BP E Cap. |
MF R : Metal Film Resistor
| CMF R | : Coating Metal Film Resistor | MM Cap. |
| UNF R | : Nonflammable Resistor | PP Cap. |
| FR | : Fusible Resistor | MPP Cap. |
PS Cap Tan. Gap. : Ceramic Capacitor : Mylar Capacitor Electrolytic Capacitor : Bi-Polar (or Non-Polar) Electrolytic Capacitor Metalized Mylar Capacitor : Polypropylene Capacitor : Metalized PP Capacitor Polystyrol Capacitor : Tantal Capacitor
Symbo!t
Outside of the P.C.B. Ass'y Symbol AVO01 ADY01
ARI AROS Acos xo1 Ico1 L041
BR BR sc WA
CH Description Main P.C.B. Ass'y CRT Socket P.C.B. Ass'y
Description APicture Tube A\Deflection Yoke PC Magnet Wedge A\Flyback Transf AFocus VR UNF Resistor 220%, 25W. K AC Capacitor 150 pF, AC1.5KV Si. Transistor IC Regulator Begausing Cecil Degausing Coil Pin Terminal (2) Degausing Coil Pin Terminal Housing Groundstrap Ass'y. Groundstrap Wire Terminal Groundstrap Spring (2) Support Bracket RH Support Bracket LH SCREW 10-% Pix Tube Mtg. (4) Pyramidal Lockwasher (4) Clip P.C.B. Support (2) Ground Lug Chassis Base
B19 Part Number SU-1103A SU-3016A
Part Number 370ESB22({E) C29123-V A76366-A €30006 A19183-A A46606-A QRF258K-221 QCZ0101-005 2SD869 STR382 21-1007-31 34-708-01 34-709-01 34-697-04 34-228-03 35-3560-01 35-3819-01 35-3919-02 31-631018-08 33-255-01 33-629-02 34-33-04 38-452-01
Malin P.C.B. Ass'y (SU-1103A) Parts List
Resistors Symbol 1406 R1408 Ri410 RI414 1415 R1421 R1.:22 AFR1401 ANR1503 1504 R1509 R1571 R1514 R1515 R1522 R1523 R1528 R1534 VR1501 4SR1703 AR1704 AXR1901 R1902 R1903 R1904 ASFR1901
Capacitors Symbol 1402 C1411 C1412 C1508 C1511 AC1512 AC1513 Ac1514 C1515, 1520 1824 C1904 1905 A\C1907
Coils Symbol 1501 1502 1503 11504 11901
Transformers Symbol 71501 71503 Description v v R R CMF R OM R OM R OM R v AF R R A\CMF R Vv R OM R OM AR OM R CMF R CMF R OM R OM R ZN ZN R R ASCMF R ASCMF R AsPosistor UNF R CMF R OM R AF R 2002 2002 6.8QIW J 3.3KQ IW J 27KQIW J 12KQ2W J 10KQ 6822W K 11, BKQYUW +1% 5KQ 1OKQ2W J 5.6KQ2W J 6802.2W J B.201W J 4.701W J 56.22W J 3902.1W J
39K QYW +1% 7.68K QYUW +1%
2Q7W K 5.623W J 1OKQ2W J 2202 %W K
Description Tan. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. BPE Cap. Cap. E E PP E APP App App PP
M E E 2.2uF 16V K 100uF 160V A 3.3uF 160V A 5600pF 50V J ATuF 160V A 2000pF DC1500V J 2000pF DC1500V J 2500pF DC1500V J 0.53uF DC1200V K tuF 50V A 0.1uF 200V K Cap. Cap. AMM Cap. 10uF 250V A 0.1uF AC150V Z
Description Peaking Coil Liniarty Coit Width Coil Heater Choke Line Filter
Description Hor. Drive Transf. Side Pin Transf.
8-20 Part Number QVZ3230-022 QVZ3230-022 QRX019J-6R8 QRGO019J-332 QRG019J-272 QRGO29J-123 QVZ3224-014H QRH024K-680M QRV142F-1182 QVZ3230-053 QRG029J-108 QRG023J-562 QRG029)-681 QRX019U-8R2 QRX019J-4R7 ORGO29J-560 ORG019J-391 ERZ-C05ZK471 ERZ-CO5DK271 QRV122F-3902 QRV142F-7681 A75414 QRFO76K-2R0 QRX039J-5R6 QRG026J-163Z QRH124K-221M
Part Number
QEE51CK-225B QEW52CA-107 QEWS2CA-335 QFP31HJ-562 QEWS2CA-476S QFZ0082-202 QFZ0082-202 QFZ0082-252 QFZ0067-534 QEN61HA-105Z QFM72DK-682M QEY0034-001 QEW52EA-106 QFZ9008-104
Part Number A75360-6 A39934 C30380-A C30333-A A39475-J
Part Number A46022-BM C39050-A
Semiconductors Symbol 101501
X1101 x1102 X1103 x1104 X1105 X1106 X1301 X1302 X1303 X1304 X1305 x1401 x1402 x1501 x1701 01101 01102 01103 01301 01401 01402 01503 01504 D1505 D1506 01507 01508 401701 4\D1901 AXD1902 A\D1903 4\D1904
Miscellaneous Symbol AXF1901 A\F1902 Description Lc.
Si. . Transistor Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. . Transistor Si
Si. Leow Transistor
Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor
Diode Diode Diode Diode Diode Zener Diode Si. Si. Diode Diode Zener Diode Si. i. Diode Si. Diode
Diode AdZener Diode ASi. Asi. BSi ASi. Diode Diode Diode Diode
Description A\Fuse 1A ASUL Fuse 3A
8-21 Part Number HA11244
2SC1685(R) 2SA673(C) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SA673(C) 28C1685(R) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SC1685(R) 2SD478 2sD478 2SC2610BK 2SC1685(P-S) WO6A WO6A WO6A 182473H 1$2473H RD10F(C) HF-1 VOsE RD11E(B) WosA 18881 182473H RD20EV2 1818874, 181887 1818874 181887A
Part Number QMF53U1-1ROS QMF66U1-3RO0S
CRT Socket P.C.B. Ass’y (SU-3016A) Parts List
Resistors Symbol R3105 R3106 R313 R3114 R3115 A3116 R3117 R3118 R3119 R3120 R3121
Capacitors Symbol C3107 C3108
Colls Symbol 13101
Semiconductors Symbol X3101 X3102 X3103
Miscellaneous Symbol A Description v R 2002 Vo OR 2002 v R 5K2 v R 5KQ v R 5KQ OM R 10K22W J OM R 10K22W J OM R 10K22W J Comp. R 3.3KQYW K Comp. R 3.3KQ”“%WK Comp. R 3.3KQ“WK
Description € Cap. 10uF 250V A C Cap. 1000pF DC1400v P
Description Peaking coil
Description Si. Transistor Si. Transistor Si. Transistor
Description ASCRT Socket
8-22 Part Number QVZ3234-022 OVZ3234-022 QVZ3234-053 QVZ3234-053 QVZ3234-053 QRGO28J-103 QRG028J-103 QRGO2gJ-103 QRZ0039-332 QRZ0039-332 QRZ0039-332
Part Number QEWS2EA-106 QCZ9001-102M
Part Number QQLO43K-101
Part Number 2802611 2802611 2802611
Part Number A75522
IX Schematics and Wiring Diagrams
SAME LOGiC 80.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
LAZARIAN CT, WIRING SCHEMATIC * Mosi-C0646-A008
DESIGNATION DESCRIPTION
cre C101 C102
C106 cios, C106, C107
cum cus. cua cus. cue. cur cue
cat
R100 R101 R02 R103 R104 oe R106
ui Rua
R20
R24 R125 DESIGNATION LIST
| DESIGNATION | DESCRIPTION | DESIGNATION | |
| Homt RE TANT | alae | 10 OHM V4W 5% CRB | HAL |
O.47m RO TANT 35V—RIZ7 eo "SA,
| 470m AX ELEC | R28 | 6.2K” | i |
R129 « 25,000 mt AX ELEC 4.7 ml ROTANT 35V
| O.tmt | RI32 | 150 OnM 2w 10% |
RI34 68 On 1/24 5%
O.tme 40,000mt Ax ELEC A7Om* Ax ELEC 2200m! AX ELEC 25
| 4700m1 AKE-EC 751 | vic, vRio1,vRIOz | 100 OHM POT |
47% mt
Fi F2
| 0100,0101,0102, | ivaiae | Fie |
(103 N40! 0106, 0107 MR 750 0108, 109 iN40o1 0110, 01,012,013, AISF Sov 5A 014,015, 06 100 OHM 1/4 W 5% CRE ut 470 * : rd 0.18 OHM 5W 5% w
| 0.16 OHM ISW 5% | 100, a101 | ans772 | ve |
68 OMMI/2W5% CRB 9102,C104y 2N2905 26 OMM 1/4 W 5% CRB 270 *
JW, gW2 JW ve L305
us M305 L2K OHMI/AW5% CRB. seo” "
TWITW2 Tw3.TW4
1.2% OHM IAW 5% CRB.
| FB1,F82 | FERRITE BEAD | ver |
250HM 5W 10% = FBMMI.FEMH2 FERR:TE BEADMTG HORV Laz
| 68 OHM I72W 5% CRE | 2-206 SOU WIRE | Le3 |
DESCRIPTION
HEATSINK ASSY. HEATSINK ASSY MTG HI RW 2-4-40X10 SLT RND = WASHER,4, 120-250 0 2-4-40 HEX NUT THERMAL COMPOUND
FUSE,1/48, SLO-BLO FUSE, IAMP FUSE CLIP w/STOF
2POS KK-156 By sos" , ‘eos 3 eros" * Ri
JUMPER WiRE
THe weap Tie wrap Ses aes Se Sea FT ' ' ' q '
. 1
i ' ' ' ' ' ' ' 7 wnsa aAnBio, t E t
| g | 6 | ' |
2100 ' L— ' 7 ' x o 1 Pry ' G
' Or i ' ' ' ' '
OA- wrnsa eaes, | 2026 fF '
| « | e | ' |
' Hy ' ° o
© 1
i rs
'
oe eeen eee ee eee 2
TAG, FUSE 1/48 $.0-BLO TAG, FUSE 1AMP TAG, WR SPLY 1D.
Oo LAZARIAN MIDWAY MFG. CO.
PWR SUPPLY TOVA F RS SSEMBELY DRAWING MEDIUM | MOS5!1-00945-A031 ENOTE: RS-RESISTOR SPACER CROSS REFERENCE LIST
| DESCRIPTION | arty | DESIG. NOS. | PART NOS. |
| 4701 | ' | cn? | 0945. 00811-c100 |
| ovat | 5 | €106.C107.61 | 0985 00811-0200 |
cus. cat
| 047 ut RO TANT 35V | f | C101 | 0945. 00816-1100 | |
| 47 ut RO TANT 35 | 1 | cios | 0945-00811 0400 | |
| NO ufRO TANT | ' | C100 | 0945-00816 -1000 | |
| 470 pt AX. ELEC | 2 | © 02.c114 | 0$45-008:6-0600 | |
| 22001 AX ELEC 250 | 1 | cus | 0945-00816 -1300 | |
| 4700 ut AX ELEC. 25 | ' | cue | 0945-00811 -0700 | |
| 25000 vt AX ELEC | ' | cioa | 0945. 00816-1700 | |
| 40000 wt | Ax.ELEC | ' | ens | 0945 00816-1800 |
| 16 OHM I5W 5% | . | R103 | 0945 00815-0100 | |
| 8 | Sw 5% | ' | Rice | 0945-00815. 0200 |
| 10 | raw 5% CRB | ' | nize | 0062-05183 «xxx |
| a | : | \ | Rios, | 0062-06585 -1xxx |
| 25 | sw 10% | ' | R24 | 0945 -00815 -1000 |
| ee" | vaws% | 3 | RI04,R125,8138 | 0062 -09803- 1 xxx |
| 100" | vawsx cKB | ' | R100 | 0062-09803 1axx |
| ipo" | 2W10% | ' | R37 | 0945-00812 - 0200 |
| 270" | aw 5% | ' | Ri06 | 0062 -13889- 1xxx |
| 470 OHM 1/40 5% | ' | R101 | 0062-15683-1xxx | |
| 560 | ; | \ | Risa | 0062-16283. 1xxx |
| * | 2 | Ri27, 8129 | 6062 -17983-1xxx | |
| 12K | 2 | R113,R120 | 0062-10383 -1xxx | |
| 6 2K OHMIZ4W 5% | ' | ni2e | 0062-217 83 -1xxx | |
| 100 onm Por | 3 | VR:00. vRi01,0845-00814- 0000 |
va ioe
| AISF 80Vv 58 0100E | 7 | 9110,0111,0812.01'3, | 0948 -00804-0200 |
0114, 0115, o116
| In 4001 | 3 | 0103, 0108,0109 | 0945- 00804-0300 |
| ma 750 | ? | 0106, 0107 | 0945-00804.0800 |
| 22905 | 2 | 0102, 0108 | 0945-00808-0300 |
| 2n 3772 | 2 | 100.0101 | 0945-00808-0100 |
| LM 305 | 2 | v2.us | 0945-00813-0100 |
| FERRITE BEAD | 2 | FoI, Fe2 | 0017-00009-0225 |
FERRITE MTG WAROWARE Fem, FOMH?
| 206 Soto wire | 2 | Fewni.Femn2 | 0017- 00033-0139 |
| HEAT SINK assy | ' | wsas | 4945.00008-0100 |
NEAT SINK MTG HAROWARE Mans
| 4-40 %10 SLT RNG | 2 | Sar | 0017-0010! -O727 | |
| WS.4, 120-250-018 | ‘ | HSA | 0017-00104. 0071 | |
| 4:40 HEX NUT | 2 | nSai | 0017. 00103-0002 | |
| THERMAL COMPOJNO | HAS REQOHSAI | 0017. 00009-0204 | ||
| FUSE, 1/44 sL0-8L0 | ‘ | f | 0017-00003 -0446 | |
| Fuse. 1 ame | : | f2 | 0017-00003-0001 | |
| FUSE CLIP w/sToP | 4 | Fire | 0017- 00003-0214 | |
| 2 POS «K-I56 CONN | ' | wt | 3000-16367-0200 | |
| > ros | 2 | vise | 3000- 16387-0500 | |
| 6 Pos | ' | v2 | 3000 -16 387-0600 | |
| 13 POS | . | ' | u | 3000- 16387-1300 |
| 22AawG 2V21N | 3 | uwi, gwe,uw3 | 0131 - 00087-0000 | |
| TIE WRAP 7-5/0 IN | 2 | Tw3, Twa | 0945-00818 -0300 | |
| THE WRAP 10 3/4 IN | 2 | Twi, Tw | 0945-00814-0800 | |
| TAG. FUSE 1/64 SL0-8L0 | ver | M051-00945.4020 | ||
| TAG.FUSE 1 AMP | ' | vez | M051-00945.4021 | |
| TAG, PWR SPLY 1.0, | ' | ves | MOS\-00945-a0z2 |
70 VA PWR. SPLY PC 4080-90421-C000
swan
anne
S8.vaw | avec J2 |
mos Ta
q vm
moe iron
7 ie | : > al
-wme eg,
avosme ty,
v conn pararcaue ave Om mace. L > ae volo car ame Ave 1 if UNREG FILTERED V wm ce Se
sesame tL one
a ° tye RT AUK _ mower 2
mee
she os,
mera iy MIDWAY MFG. Ci
MEDIUM PwR SUPPLY 70 VA A982-9042I- C090 M051-00945-A03a
9-5
DESIGNATION,
co 1OOOPF CER. Disc 1 -1UF CER. O18¢ 2 1OO0PF CER. vIsc cs lOUF ELECTROLYTIC ca .O1UF CER. DISC
| cs | 1oooPr | CER. Disc |
ce 3SOPF CER. O1SC °7 IOOPF CER. DISC ce 330PF CER. DISC co IOOOPF CER. O18 cio 1OOOPF CER. DISC Cl-cI3 100 PF CER. Disc cia 100 UF ELECTROLYTIC Cl8-C22 330PF CER. DISC cas 100 UF_ELECTROLYTIC. 24 -1UF CER. DISC ces lOOUF ELECTROLYTIC cae s1UF CER, OSC 27 JOOUF ELECTROLYTIC cee <1UF_CER. Disc cae S3OPF CER. DISC C30-c45 .IUF CER. DISC «coe 22PF CER. isc cio lOOPF CER. DISC
Ri-RiO Rul Ri2 : RI3-216 *
| RIS-RIT | 1K | * |
| RIB-RIO | 2.2K" | : |
| R20 | 47K" | 7 |
| Rai | 22K" | * |
R22-R27 4.7K" # R20-R34 2.2K" : R3S-R42 4700" .
| Ra3 | 47K" | . |
Rae-Rae IK . Ra7 * Rae . Reo . R50 “ RS! . Rez * RSS : Roe = R58 . RSG-RS7 4.7K" .
| R5e-R59 | 1K" | . |
| RGO-RBI | 2700" | . |
| R62 | 8202" | 7 |
Res ik” Res OPEN RES-REG 820 1/4w 5% Re7 270"
| Reo | IK | * | . |
| Res | 3.3K" | . | |
| R7O-R71 | 100.0" | - | |
| R72 | 3.3K" | * |
R73-R74 1K
| R75 | 3.3K" | . |
| R76 | 4.7K" | : |
| RI? | IK | . |
| 78 | 4700" | - |
| R79 | 100 a" | . |
| Reo | 22K" | . |
| Ret | 270n* | . |
| Rez | 47K | : |
| Pas | 22K | . |
Pat IO<OPINSIE. awe 2.2K 9PINSLP M3 3.3K 9 PINSLE
O-0I7 NAIA 018-020 IN¢004 pat Inala
8c337 acs48
OCATED ON PINS 6&7 OF Icl2c 1c78 1c7e \c7E Ic7F \c7FG 1c76 1c7H ac7t \c7™
Ieee Icor ices. ican ice
Icec 1c90 icse. Icor IcoH Ico IcoL,
iclop Icio ICloE IClOF Ic106 Iclow tc101 Icrou, ic10M
iene tcuc. icuo IcHE Ics tcun tent iene tcum
PROJ. ENG,: J. JARON DESIGNATION LIST
EPROM ici28 ieee nese 1cl20 Tatseee TALSI74 a 40097 fone reign racsai (oat 74.804 reek
EPROM roi
ernow ici3a 2636 Ici3B 74L$245 iciac Mtsse ele fooer (else raise SSE Tatssre 188 Tasers SM soa! 113
eprom rela PROM 1Cl4A 2ese iciae tse 114 russe (eis Titssre 12D maussre ISLE
teiao cpnon iclen eprom teat aie "eee Taser tla resie flan Tatsies \cise Tatsare 1188
teis0 reise cpnow Ieige EPROM Icl56. ire ieren Faso reist Tasos elo Tacsi3e Tate cea ac e528, Taussre SSE 68,6C,78,7C, ratsoz STOTT. muses slow EPROM Ics9c,2e, T4LS32 3E,5E Tatsare
a 2650 at 7a1s08 ve racsos eat T4166 N26 74Ls832 Js Taso 3 Histo rr se he T4L S244 J? acseae
Etnow mser swhowe aceite mises eesioo
74804 peat reuse ralee conou muses
ratsees Taoe
useo on LAZARIAN 74L$00 7aLso4 74LS74 7AaLsie7 2ue 74Lse aus 7aLsee3 740e
TaLsil2 TALS74 T4ALS90 74Lsi87 748187 Qua eT245 74LS86 74.888 74Ls2e3 7406 a a 74csi2 TaLsoz 74LsI61 TaLsi6! T4LSIB7 Ty —J z Py ar wat [Sor [sor S37
ana 7aLs244 7aLse6 7aLses EPROM 74166 TaLS3e
74Ls260 oa oer 3a Bor Ny Shon
74Lsi6l 74LSI61 7ALSI87 sor [Sor oo)
TAL S373 7aLsee 74s85 ner Wer cy Wor We He node Fal
74166 34
14PIN 24PIN PLT ER rs He We
Tor ry
28PIN 4b veo 40 PIN
2POS.KKIGE CONN. 9Po0s." i 2POS.KKIOO CONN. so i Te 7a Tor ers ne ims
wor wer war om ost o3—
eke} eke)
- wSI
14P0s."
JUMPER WIRE S91
8 POS. DIP SW. wo rw O wa eu —— ea
DESCRIPTION QUANTITY 2POS.KKIS6 STR. CONN, ' 9Pos. * . '
2POS. KKI00STR.CONN. 3Pos." * 4Pos."
upos." “ l2pos. . '
. 2 sPos." : ' st '
'
MIDWAY MFG. CO. FULL Ne. re0° ONE (i) 14Pos." :
JUMPER WIRE 2
[os 6/24 /82 | GAME LOGIC BOARD A084-91419-C636 COMPONENT LAYOUT DRAWING MOS! ‘8 POs DIPSW 2 -00636 -CO05 14318 MHZ CRYSTAL, ' DESIGNATION PART HOS ul 3000-16367-0200 vt 3000-16367-0900
Je 3000- 16437-0200 92,07 3000-16 437-0300 J2d6 3000-18 437-0400 M5 3000-16437-0500 Js 3000-16437-0600 wa 3000-16437-0700 J 3000- 18437-1100 J3,08 3000-16437- 1200 uv 3000-16437 1400
wei 0017- 00033-6373
swisw2 (0636 - 00804-0200
XTAL 0636 00804-0100
LAZARIAN LOGIC BD PC A080 -91419- C636 CROSS REFERENCE LIST DESCRIPTION _ 22 PF CER.DI8C 10oPF™ 7 ‘330PF" . 1000PF™ * sO1UF TUF 20 1OUF ELECTROLYTIC ' 1oouF" . Quantity
Joon v4w 5% 3 lo ' z7o" 4 470" 0 szo" 3
| iow | 8 | 8 |
| 2.2K" | " | 7 |
= z e ou
# an
74LS00 7aLso2 TaLso4 74304 7406 74LS08 74Lsio 7aLsi4 7aLs2i 74.827 74L832 7aLs74. 74Ls85 74Ls86 74Ls90 74Lsii2 74Lsi25 74LSI39 7ALSI55 74LsI56 7aLSi57 Om W-N-BANEN— WH OH
7a.siel 7acsies 74166 7ausi7a TaLs244 T4LS260 74L S283 7ALS373 74Ls376 es avan®
o
2621 26036 2680 3081
40097 928100 8T245 (7418245) Ronan
EPROM E7ROM eprom EPROM EPROM EPROM EPROM EPROM EPROM EPROM EPROM EPROM EPROM EPROM
14 PINIC SOCKET 1
| 24 PIN | : | 4 |
| 2ePIN" | " | ' |
| 4orIn” | 7 | 4 |
-DESLGNATION cos €7,C11-€13, clo 66,c8,cIS-c22,c20 €8,62,C8,C9,c10 C4 €1,024,026,628,C30-C48 cs ¢14,¢23,¢28,c27
R70,R71,879 RII ROO-REI,RO7,ROI RIS-RI4 .R3B-R42,R78 R62,R65,RES RIG-RI7, R44-R46,REG-REO, RO3,RO8, R73-R74,R77 RIG-RIO,R2I,RZO-R34, RAT, RAB, RBILLRES, RSS, R80, RES ROOR72, R75 RI-RIO,RI2,R20,R22-R27, R388, R60, RZ, RS RBgRataresney
RM2 RMS. RMI
018-020 DI-DI7,021
aires a4-a8
iB 7 FG, BE,14B 2M,7H,9E, 91,126 1B 11M, 12M, 13M
FOL 7M, D au 10H 56, 8H,9H, 14N 120,138 121,131 141151 TH I2H.I3HI4H,15H 13c I3A,14A 1oe 46,76
SFO, 6FS WL IZE, 180 I3E, 14E,18E 146,140, 18¢,150 8F OF JOFJIF,14M,15M 2H,101 26,10, 10¢,146
TOL. HL IZL, ISL
3H4H,4 L5H, 51,81, 71 8E GE,7E,I2F,I3F, OF, 15F ue 2€, 36,5 9c au
23,31 tom 36,136
2c 3c 5c ec re
Ne rau
Iestic 1cS28, 2¢,38,3C,58, SC, 68, 6C,78, 7C, 66, 106, 116, 14L. 1csioM 10896, 2€,36,5E ~PART.NOS.
0€36-00800-0400 0836-00800-0800
0@36-00800- 0600 0836-00800- 0800 0@38-00800- 0300 (0€36- 00800-0200 0836-00800- 0100
0636- 00805-0600
0638-00805- 0700
0@3e- 00805-0800 0636-00805 - 0900
0636-00808 - 1200 0636-00805 - 1100 0836-00808- 1000
0836 - 00801-0100 0@3e- 00801-0200
0636-00802-0100 0636-00802-0200
0636 00803 0600 0636-00803-0700 0636-00803-0800 0636-00803-3000 0636-00803-2400 0636-00803-0900 0636- 00803-1000 (0836-00803- 1100 0636- 00803-0200 0836-00803-1200 0636-00803-1300 0636-00803-1400 0636-00803-2900 0636- 00803-0500 0636-00803-2500 0636- 00803-0400 0836-00803-2600 0636- 00803-1500 0636 - 00803-0300 0636- 00803- 2700 0636- 00803-1600
0636- 00803-1700 0636-00803-1800 0636-00803- 6300 0636-00803-1900 0636- 00803-2000 0636 -00803- 2800 0836 - 00803- 2100 9636-00803- 2200 0636 ~- 00803-2300
0636- 00803-3800
0636- 00803-6200 0636- 00803- 3600 0636-00803 - 3500 0636- 00803- 3200
0636- 00803- 3400 0636- 00803-3100 0636 - 00803-3700
0636-00803-4800 0636-00803-4900 0636-00803-5000 0636-00803-5100 0836-00803-5200 0636-00803-5300 0836-00803-5400 0836- 00803-5500 0636-008 03-8600 0836" 00803-5700 0636-00803-5800 0636-00803-5900 0636-00803-6000
- 00803-6100
0€36- 00804-2800 0636- 00804-2900
9636- 00804-3100 0636 - 00804-3000
9-7
DESIGNATION LIST CROSS REFERENCE LIST
| oesceiprion | Designation | pescnption | “sescppriow | quanrity | DESIGNATION | pant Nos, | ||||
| IMF CER DISC. | Leaitlenl! | as see. | Olmt | 3 | C18,C20,c40 | 0636~- 00800-1100 | ||||
| \OOOPF CER. OIC. | ue | Feenk. | 047 mt POLY. | 1 | 22 | 06 36-00800-1200 | ||||
| 1 OOOMF RO. ELEC. | = | bchagroerh | mt CER. O1SC. | 2 | Ci-C4, 66,08, | 0636- 00800-1300 | ||||
| OME TANT | — | poreicinge | Ome | k | 2 | cIRcae | 0636- 00800-1700 | |||
| IMP CER. DISC. | Pry | 2 PIN CONNECTOR | \OOOmERD. ELECT. | 3 | ca, C10, C31 | 0636- 00800-1900 | ||||
| atime te mag | ee) | a" | by | 7 | re | 1 | Rie | (0062 ~ 04283-IKKX | ||
| pecore caeabis | a | “ | . | aa | whe | 70" | : | 2 | aissnie | Coee = 15603-14KK |
| 26 | 1OMF TANT | awe | ws} | Ks, | 3.9K" | = | 1 | R60 | (0062~ 20703-1xxx | |
| eae, | \OOOWE ROLELEC. | snus | Nut, 8-40 HET | : | 1 | Ras | 0062 ~ 22383-1Kxx | |||
| on | ‘ur Cenbse | AS REG. | HEATSINK COMPOUND | F | {4 | . | 4 | RG, REE, R68,R82 | Soee~22783-1kRX | |
| Rio—Rit | «* | 5 | i | | A | . | 5 | (0062 25985-1Kxx | |||
| Riz | a7 | 3 | [a | Ce | q | 0062 - 26783-1Kxx | ||||
| Ri RIS | aro" | * | | | . | ' | 0062-27 SB3-1Kxx | ||||
| Rie ni9 | ban? | : | | | t | 082-2080 5-1Fxx | |||||
| R20-R2I | am * | . | L | . | 1 | OO€2~ 291B3-1XXX | ||||
| nes | vox | 7 | 0836 - 00803 ~ 3800 | |||||||
| - | . | = | 0636 - 00803 - 4400 | |||||||
| aes | ae | i | S | ra08 | Os36 - 00803 ~4100 |
R37—R30 Lenina
| coy | am = | . | HEATSINK MTS. HROW | ait | loot) | 0005 7;5/08 82) |
| vet | 10K Por. | esata am et | ' | — | R080 90B11— E636 |
PROJ, ENG. J. JARON Ec tAEARTAN T QIDWAY MFG. CO. sat LAZARIAN SOUND BOARD a fe —| component DRAWING JMosi 00636 -E007 = eni0 fa Ae4-- 9031 F636
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
DESIGNATION LIST
DESIGNATION
cl- c3 c4- C6 c7-c9 clo- cl2 C13
RI-R3 R4- R6 R7- R9 RIO- RII R12
Ql - Q@3
Jl
J2
MH I-MH4 DESCRIPTION
|OMF I6V «| MF 50V |OMF I6V 22PF 50v 5% ISMF 20V 20%
6.8K /4W 5% 3.3K" iK " 300n" " 2700" "
MPS A20
3 POS.CONN. 5" "
2 Pos. CONN. 4"
SNAPBUSHINGS CROSS REFERENCE LIST
DESCRIPTION
|OMF I6V
IMF 50V
IOMF I6V
22PF50V 5%
ISMF 20V 20%
6.8K 1/4W 5%
3.3K" "
KO" .
300n" "
2700" "
MPSA20
3 POS. CONN.
5 POS. CONN,
2POS. CONN.
4POS. CONN.
SNAPBUSHINGS QUANTITY DESIGNATION.
-Cc3
c4- C6
c7-c9
cio-Ccl2 a waa
1 ci3
RI- RS
R4-R6
R7- RO ny ow G Ww
RIO-RIl
I Rl2
3 QI-Q3
l Jl
| Jl
| J2
I J2
4 MH I-MH4
MONITOR INTERFACE P.C. BD.
PROJ. ENG. + J. JARON
DO NOT SCALE DWG PA NOS.
0636-00800- 2100
0636- 00800-2000
0636- 00800-2100
0636-00800-2300
0636-00800-2 200
0062-—219B3—1XXX
0062- 203B3—I1X XX 0062-179B3— IXXX
0062-141B3— IXXX
0062-138B3- IXxx
0636 - 00802-0400
3000-16387 -— 0300 3000- 16387 — 0500
3000-16387 — 0200
3000-16387 — 0400
0017 — 00042-0014
A080- 914 22-B636
useo on LAZARIAN
NO. REQ’D 1 (ONE) PER REVISIONS
MIDWAY MFG. CO.
FRANKLIN PK. ILL
DIM TOLERANCES UNLESS SPECIFIED
CONCENTRICITY TER 003 FRACTIONAL + 164] oecimac “estou 5/9 7/B) HOLE OIA — + 002 000] LAZARIAN MONITOR INTERFACE ASSEMBLY DRAWING A084 - 91422 — B636 PART NO.
MO51—O0636 — BOI6
+5V AMF c4 +);C7 1OMF
° N a
=
+ 1OMF
ClO 22PF
+5V +5V
C5 .IMF
c2 + 1OMF | KEY!
AMF + cil 22PF
Q2 MPSA20
‘tM. TOLERANCES
CONCENTRICITY TR
FRACTIONAL 2
DECHAAL + HOLE O1A + 002— ANGLE 100 NOT SCALE DWa +5V
UNLESS OTHERWISE SPEC a C6 == +469 IOMF Ccl2 22PF
PROJ.ENG.: J. JARON Q3 MPSA20
eae a
005, ‘000 212" FRANKLIN
SCHEMATIC THIS DWG. IS CONFIDENTIAL & PROPERTY OF MIDWAY MFG_CO
MIDWAY MFG. CO. IL. 60131 LAZARIAN MONITOR INTERFACE P.C. A0@4—91422—8636 REVISIONS PART NO 05:1 -00636 BOI 7 9-11
| DESIGNATION | LIST | CROSS REFERENCE LIST | ||
| DESIGNATION | DESCRIPTION | DESCRIPTION | _QTY. | LOCATION _PART NOS._ |
| OI-DI6 | IN4004 | IN4004 | 16 | DI-DIG 006 4-O30XX-XXXX |
| 2POS.KKIS6 | 1 | Jl | 300046387 -0200 |
vl 2POS. KKI56
| 14P0s. " | " | 3Pos" | “ | ' | J2 | 3000-16387- 0300 |
| , | 4pos" | “ | | | ve | 3000-16387- 0400 |
v2 KK
| ros ne | sPos" | “i | J3 | 3000-16387-0800 | ||
| v3 | SPOS. KKIS6 | 7Pos." | " | ' | J4 | 3000-16387-0700 |
| pos." | M4 | ePpos."" | “ | | | v3 | 3000-16387-0800 |
| y4 | 4POS. KKIS6 | npos." | “ | ! | J2 | 3000-16387-1100 |
| 7P08S. “ | « | i4Pos"——“ | ‘ | vi | 3000-1638 7-1400 | |
| MHI-MH4 | SNAP BUSHING | SNAPBUSHING | 4 | MHI- MH4 .0017- 00042-0014 |
PROJ. ENG.: J. JARON THIS DWG 1S CONFIDENTIAL & PROPERTY OF MIDWAY MFG CO unvess ormenwise sec Pot” ores — MIDWAY MFG. CO. CONCENTRICITY T} A 002 4/82 FRANKLIN PK.1L.60131 4 BALL CO
| FRACTIONAL | + 164 | 1 624/62 | FULL | a |
= oe REVISIONS
| DECIMAL | soo | Pe | LAZARIAN DIODE P.C. | “oo |
| MOLE OVA | “4 | pf | COMPONENT LAYOUT | es |
ANGLE 12
| DO NOT SCALE DWG | \ | A084-91421-C636 | o>! |
00636 CO!15
bI6 O13
ALL DIODES ARE IN4004
PROG.ENG.: J. JARON DIM. TOLERANCES rest. 6 L AZARIAN : UNLESS OTHERWISE SPEC. CONCENTRICITY T.LR. .. .002 PS /82 Fu LL WATE FRACTIONAL £1164
EO [FRISH a ee THIS DWG. IS CONFIDENTIAL & PROPERTY OF MIDWAY MFG. CO.
pA all adbettcee LAZARIAN DIODE PC. SCHEMATIC A084 —91421—C636 REVISIONS DECIMAL . + 005 HOLE DIA. + .002—.000 ANGLE ......... 212° DO NOT SCALE DWG 10-5: 1-0-0636 -C0:1'4] 9-43
LAZARIAN GAME LOGIC BOARD DEVICES (P.C. A084-91419-C636)
Chip Chip
Number Function Number Function
| 74LS00 | Quad 2 Input NAND | 74L$174 | Hex D Type Flip-Flop |
| 74LS02 | Quad 2 Input NOR | 74LS244 | Octal Buffer —Tri State |
| 74LS04 | Hex Inverter | 74LS245 | |
| 7406 | Hex Inverter Buffers/Drivers | or 81245 | Octal Bus Transceiver |
| 74LS08 | Quad 2 Input AND | 74LS283 | 4 Bit Binary Full Adder |
| 74LS10 | Triple 3 Input NAND | 74L$373 | Octal D Type Latches — Common Enable |
| 74LS14 | Hex Schmitt-Trigger Inverters | 74LS374 | Octal D Type Flip-Flop — Common Clock |
| 74L821 | Dual 4 Input AND | 2650 | 8 Bit CPU |
| 74LS26 | Quad 2 Input NAND — High Voltage | 2732 | 4K x 8 EPROM |
| 74LS27 | Triple 3 Input NOR | 2716 | 2K x 8 EPROM |
| 74LS32 | Quad 2 Input OR | 2636 | Programmable Video Interface |
| 74LS74 | Dual D Type Flip-Flop | 2114 | 1K x 4RAM |
| 74LS85 | 4 Bit Magnitude Comparator | N82S100 _ Field Programmable Logic Array | |
| 74LS86 | Quad 2 Input Exclusive — OR | 2621 | Universal Sync. Generator |
| 74LS90 | Decade Counter | CA3081 | Transistor Array — NPN |
| 74L$112 | Dual J-K Flip-Flop | 40097 | Hex Buffer — Tri State — CMOS |
74LS125 Quad Buffer — Tri State 74LS139 Dual 2 to 4 Line Decoder
| 74L8155 | Decoder/Demultiplexer — Totem Pole | ‘ADDITIONAL'DEVICES | |
| 74LS156 | Decoder/Demultiplexer — Open Collector | 14.318 | Xtal |
| 74LS157 | Quad 2 to 1 Line Multiplexer | BC548 | NPN Transistor |
| 74LS161 | 4 Bit Binary Counter | BC337 | NPN Transistor |
| 74LS164 | 8 Bit Parallel Output Shift Register | 1N4148 | Diode |
| 74166 | 8 Bit Shift Register Parallel/Serial Input | 1N4004 | Diode |
LAZARIAN SOUND BOARD DEVICES (P.C. A084-9091 1-E636) Chip Number Function
74804 Hex Inverters 7406 Hex Inverters Buffers/Drivers 74LS156 Decoder/Demultiplexer — Open Collector 74LS161 4 Bit Binary Counter 74LS374 Octal D Type Flip-Flops 4016 Quad Bilateral Switches — CMOS TMS3615 Organ Tone Generator
SN76477 Complex Sound Generator
TDA 1010A 6 Watt Audio Power Amplifier 4.0000 Xtal BC557 Transistor PNP 1N4148 Diode 1N4004 Diode