CATHODE RAY TOMES

Street Fighter II

Super Street Fighter II: The New Challengers (World 931005) (Capcom, 1993) · Manual · 20 pages · 22 sections · original scan

Page 1

Tne Diew Gnrelieneer © CAPCOM 1991, 1993. ALL RIGHTS RESERVED.

MANUAL

WARNING

This game is for use in the United States of America and Canada. Sales, export or operation outside of these countries may be construed as copyright and trademark infringement and is strictly prohibited. Violators are subject to severe penalties and will be prosecuted to the full extent of the law.

CAPCOM

USA

Page 2
WARNING

THIS GAME MUST BE GROUNDED. FAILURE TO DO SO MAY RESULT IN DESTRUCTION TO ELECTRONIC COMPONENTS.

WARNING: This equipment generates, uses and can radiate radio frequency energy and if not used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a CLASS A computing device pursuant to SUBPART J and PART 15 of FCC RULES, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.

(— >)

“WINNERS DON’T USE DRUGS” William S. Sessions, Director, FBI

*IN COOPERATION WITH THE AAMA AND FBI ANTI-DRUG CAMPAIGN*

CAPCOM, USA INC.

INVITES YOU TO USE

OUR SERVICE NUMBER FOR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER CAPCOM GAME YOU NOW HAVE ON LOCATION. PLEASE HAVE GAME SERIAL NUMBERS AND CABINET NUMBERS READY.

CALL US FOR PROMPT, COURTEOUS

ANSWERS TO YOUR PROBLEMS.

Direct Number (408) 727-0400

Page 3

CAUTION

Please keep the following instructions to keep the PC board in good condition

board in good condition. ¢ Do not block up the ventilation slots.

¢ Do not give the board too much shock.

  • Do not let any liquid go inside the case.
  • Do not disassemble the case.

ORY. Attention:

The product that you have purchased contains a rechargeable battery. GS The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or Ni-Cd proper disposal.

Disassembling the case or removing the sticker may cause the termination of your repair warranty

may cause the termination of your repair warranty.

Page 4

© SETTING INSTRUCTIONS

  • PCB CONNECTOR

JAMMA STANDARD

¢ CRT MONITOR

HORIZONTAL SCREEN

MOVE MOVE

LEFT RIGHT

on CD (Greonsy SS Ox S — So

ck

  • 8-WAY LEVER

MOVES PLAYER TO UP/DOWN, LEFT/RIGHT AND OTHER DIRECTIONS.

@ CONFIGURATION

COIN COUNTER JAMMA STANDARDS SOLDIERS SIDE COMPONENTS SIDE 1 |GND 2 |GND 3 |+5V 4|+5V 5 JN.C. + 12V,

GND} GND} 27|GND 28|GND c D E F H J |COIN COUNTER 1 K (COIN LOCK OUT 1) L | 10|SP(+) M/J1I)N.C. N}12/VIDEO RED P |13|VIDEO BLUE R | 14/VIDEO GND N.C] S | 15|TEST SW COIN SW 2) T | 16|COIN SW 1 START SW 2} U | 17/START SW 1 2P UP| V | 18|1P UP 2P DOWN| W | 19/1P DOWN 2P LEFT| X | 20|1P LEFT 2P RIGHTY Y |21|1P RIGHT 2P PUNCH} Z\22 IP PUNCH 2P PUNCH| a |23 1P PUNCH 2P PUNCH) b |24)1P PUNCH N.C.} ¢ |25|N.C. N.C.| d [26)N.C.

e f

+ PARTS NAME CR7E-56DA-3.96E : (HIROSE) OR 1168-056-009 : (KEL)

COMMUNICATION (TOURNAMENT) IN (BLACK) OUT (GRAY) AUDIO OUT<FOR QSOUND> (RIGHT : RED, LEFT : WHITE)

TEST SW VOLUME-UP SW VOLUME-DOWN SW

Page 5

® CONNECTORS

JAMMA: JAMMA 56-pin connector OPTION: optional I/O connector AUDIO OUT: used only for CAPCOM QSOUND cabinet COMMUNICATION: I/O connector for the Tournament Mode

IN (Black): input OUT (Gray): output

@ 1/0 EXTENSION CONNECTOR

33 }OOOOODOOOoOoooooooOD! AWG20 Black GND 34 |[DO000000000000000)|, GND AWG20 Black

IP SHOTS (IP Kick Light) AWG22 Sky Blue wi IP SHOTS (1 Kick Middle) awe Est

AWG22 Pink

IP SHOT6 (IP Kick Heavy)

2P SHOTS (2P Kick Light) 2P SHOTS (2P Kick Middle)

2P SHOTS (2P Kick Heavy) AWG22 Pink/Yellow

TEST: Test switch of the circuit board

VOLUME

UP: Volume-up switch DOWN: Volume-down switch

OPTION connector

GND AWG20 Black

GND AWG20 Black

IP SHOT (IP Kick Short)AWG22 Sky Blue—

IP SHOTS (1 Kick Forward) AWG22 Red =, IP SHOT6 (IP Kick Roundhouse) AWG22 Pink ss

2P SHOTS (2P Kick Short)AWG22 Grey/Yellow—
2P SHOTS (2P Kick Forward)AWG22 Pink/YellowoO

2P SHOTS (2P Kick Roundhouse) AWG22 Purple/Yellow —— AWG22 Grey/Yellow

AWG22 Purple/Yellow

Page 6

ABOUT EEP-ROM | This board is equipped with EEP-ROM which can store various settings without backup battery. The EEP-ROM lets you change settings on screen. Please see the chapter SYSTEM CONFIGURATION for particulars.

ABOUT TEST MENU | | 1) TO OPEN THE MENU

A) For CAPCOM cabinet, or a cabinet equipped with a test switch Turn on the main switch, then push the test switch. The screen A shown below will appear. B) For a cabinet without a test switch Push the test switch of the circuit board. The screen A shown below will appear.

| 2)TO CLOSE THE MENU | On the test menu screen, select “9.EXIT” and push 1P A button.

TEST MEN U

INPUT +1, Check on input switches OUTPUT +2. Check on output switches SYSTEM CONFIGURATION +3, Game play settings MEMORY TEST --4, Memory check SOUND & VOICE +5. Sound check COLOR --6, Color adjustment DOT CROSS HATCH -»7, Adjustment of screen size, focus and distortion CHARACTER +8. Character check EXIT --9, Returns to the game play mode sk ok CONAN ARWNH

(*Screen A)

| 3) BASIC DESCRIPTIONS; HOW TO SELECT AN ITEM

Select an item with IP lever and decide with 1P A button. To return to the test menu, push 1P START and 2P START buttons simultaneously. ** The test menu automatically appears: e After changes of game play setting are done on the menu of “3.SYSTEM CONFIGURATION” e After the memory is tested on the menu of “4.MEMORY TEST”

Page 7
  • ITEM DESCRIPTIONS
  • INPUT =
  • OUTPUT Used to test all the input/output switches. “1” appears when the switches are on.

Check connection and switches in case “O” appears.

  • SYSTEM CONFIGURATION Used to change game play setting. See the next chapter.
  • MEMORY TEST Used to test the memory.

“OK” appears when it works normally. “ERROR” appears in case of malfunction, then repeat the memory test.

Contact your dealer if “ERROR” still appears.

  • SOUND & VOICE Select a code of SOUND or VOICE with the 1P lever.

Push the 1P A button to hear the sound of the selected code, then

adjust volume.

  • COLOR Shows color bars of red, green, blue and white.

Adjust RGB and brightness to obtain the optimum color balance and

solid-black background.

  • DOT CROSS HATCH Used to test screen size, focus and distortion.
  • CHARACTER Used to check all the characters.
  • EXIT Select this item and push IP A button to return to game play mode.

SETTING THE VOLUME

The volume of this unit can be adjusted by pressing the volume-up switch and volume-down switch. The setting you have selected will be stored even if the power is turned off. In the event that the volume setting does not work properly, press down on either the volume-up or the volume-down switch for at least five seconds, then set the volume again.

Page 8

| ABOUT SYSTEM CONFIGURATION | [ 1) TO OPEN THE MENU | ¢ On the TEST MENU screen, select “3.SYSTEM CONFIGURATION” and push IP A button. Screen B shown below appears. e The word “TOURNAMENT” in this manual should be referred to the term “ULTIMATE COMPETITION.”

  • TO CLOSE THE MENU |

e When all the settings are done, select “EXIT” and push 1P START button. e When settings are changed, new settings are stored on EEP-ROM, then the TEST MENU appears. e A message “SAVING NEW CONFIGURATION IN EEP-ROM” appears while new settings are being written on EEP-ROM. e It takes one or two seconds to write new settings on EEP-ROM. Do not tum off the power switch while writing. e A message “CONFIGURATION SAVED” appears and then the TEST MENU automatically appears when writing is done.

SYSTEM CONFIGURATION MENU

>GAME MODETOURNAMENT--Game mode setting
COIN1COIN1CREDIT--Number of coins per play
COIN CHUTER2 CHUTERS--Coin chuter setting
GAME DIFFICULTY4/MEDIUM--Game difficulty setting

SOUND --Stereo or monaural DEMO SOUND --With or without sound in attract mode CONTINUE +-With or without continued play START MODE ---A one-player game from the two-player (2P) side start up

MONITOR FLIPOTEACOVMAMMI\eCM--Turnover of the screen ---Retums to factory setting

EXTEND PLAY 3 EXIT --Setting extended play ---Returns to the TEST MENU

(*Screen B)

| 3) TO CHANGE THE SETTING |

e Select an item with 1P lever (UP or DOWN) and and change the setting with the IP lever (LEFT or RIGHT). Settings will be changed in the order shown in the following table. You can also change the setting with the 1P A button.

Page 9

SYSTEM CONFIGURATION

  • MENU
1 COIN1 COIN1 COIN1 COIN1 COIN

1CREDIT | 2CREDITS | 3CREDITS | 4CREDITS | 6 CREDITS COIN

2. COINS3 COINS4COINS| 2COINSTART
1CREDIT| 2CREDIT |1 CREDIT|1COINCONTINUE|FREE PLAY
1234

EASIEST VERY EASY EASY MEDIUM

GAME DIFFICULTY

5678

MEDIUM HARD HARD VERY HARD HARDEST

SOUND STEREO (QSOUND) MONAURAL

DEMO SOUNDONOFF
CONTINUEONOFF
START MODEONOFF
MONITOR FLIPONOFF
  • Bold faces indicate the factory setting
  • After you change the setting, make sure to select “EXIT” and push the 1P START button. Otherwise your setting will not be memorized.
Page 10

SYSTEM CONFIGURATION

ITEM DESCRIPTION

COIN Sets the charge per play.

  • The number of selections possible is different for the Tournament Mode and the Single Mode. T: Sets the charge per play for the Tournament Mode. (5 selections) S: Sets the charge per play for the Single Mode. (10 selections)

GAME DIFFICULTY As the number increases, the game play gets harder.

SOUND STEREO or MONAURAL. QSOUND is available with CAPCOM QSOUND cabinet only. For other cabinet, please set to MONAURAL. + STEREO - with QSOUND + MONAURAL - without QSOUND

DEMO SOUND With or without sound in attract mode. *ON-with sound — + OFF - without sound

CONTINUE Sets continuous play. ON: Continuous play is possible. OFF: Continuous play is not possible.

  • In the Tournament Mode, this item is automatically set to “OFF”, and cannot be changed.

START MODE Sets whether or not it is possible to start a one-player game from the two-player (2P) side after game start up. ON: Game can be started from the two-player (2P) side. OFF: Game cannot be started from the two-player (2P) side.

  • In the Tournament Mode, this item is automatically set to “ON”, and cannot be changed.

MONITOR FLIP Turns over the screen. If the screen appears upside down, change the setting.

  • ON - with turnover ¢ OFF — without turnover

FACTORY SETTING To return to the factory setting, select this item and push the 1P START button.

EXIT To store changed setting and return to the TEST MENU, select this item and push the 1P START button.

Page 11

STARTING UP THE SINGLE MODE

The Single Mode allows a player to challenge the computer alone or, in the event another player shows up, two players to play each other. Even with the communications cables for the Tournament Mode connected, the Single Mode can be easily started up simply by changing the game mode.

*If you wish to start up the Single Mode while the communications cables for the Tournament Mode are connected, be sure to set all four units to the Single Mode. (The Tournament Mode only works when four units are connected to form one group.)

| 1) SETTING PROCEDURE After switching on the power, press the test switch to display the test menu screen either during the Terminal Check or during the tournament demonstration game. Here, select “3.SYSTEM CONFIGURATION”, set the “GAME MODE” to “SINGLE”, and then exit the test menu. (Press the one-player (1P) start button.) This completes the setting. Now the unit can be operated in the Single Mode. If you wish to change the game mode settings, press the test switch once again to select the test menu, and then change the settings.

Page 12

HOW TO EJECT THE CARTRIDGE | 7 Cartridge

Case clamper

Main board

STICKER DESCRIPTIONS

Sealing sticker

Serial number sticker uy

Warning information sticker Game title sticker

Reverse side of the cartridge Cartridge

Main board

Serial number sticker

*Disassembling the case or removing the sticker may cause the termination of your repair warranty.

Page 13

HOW TO MOUNT THE P.C. BOARD

  • Mounting the feet

4 pieces of the PCB feet are included in the package.

| 1) Mounting the P.C.B.

Page 14

© CAPCOM 1991, 1993. ALL RIGHTS RESERVED.

MANUAL

WARNING

This game is for use in the United States of America and Canada. Sales, export or operation outside of these countries may be construed as copyright and trademark infringement and is strictly prohibited. Violators are subject to severe penalties and will be prosecuted to the full extent of the law.

Page 15

SYSTEM CONFIGURATION

  • MENU

GAME MODE TOURNAMENT SINGLE

T1 COIN2 COINS3 COINS4 COINSFREE PLAY
1 CREDIT1 CREDIT1 CREDIT1 CREDIT
COINGAME1 COIN1 COIN1 COIN1 COIN1 COIN
MODE1 CREDIT2 CREDITS3 CREDITS4 CREDITS6 CREDITS

Ss

2 COINS3 COINS4 COINS2 COINS STARTFREE PLAY
1 CREDIT1 CREDIT1 CREDIT1 COIN CONTINUE

COIN CHUTER 1 CHUTER 2 CHUTERS

1234

EASIEST VERY EASY EASY MEDIUM

GAME DIFFICULTY

5678

MEDIUM HARD HARD VERY HARD HARDEST

SOUND STEREO (Q SOUND) MONAURAL

DEMO SOUNDONOFF
CONTINUEONOFF
START MODEONOFF
MONITOR FLIPONOFF
EXTEND PLAYOFF2345EVERY
  • Bold faces indicate the factory setting.
  • After you change the setting, make sure to select “EXIT” and push the 1P START button. Otherwise your setting will not be memorized.
Page 16

SYSTEM CONFIGURATION

ITEM DESCRIPTIONS

GAME MODE Sets the GAME MODE.

  • TOURNAMENT — Tournament Mode + SINGLE - Single Mode
  • Please see the chapter STARTING UP THE TOURNAMENT MODE.

COIN Sets the charge per play. ¢ The number of selections possible is different for the Tournament Mode and Single Mode. T: Sets the charge per play for the Tournament Mode. (5 selections) S: Sets the charge per play for the Single Mode. (10 selections)

COIN CHUTER Sets the configuration of the coin chuter. Select the appropriate configuration for the unit being used. In the Tournament Mode, if two chuters are selected, coin insertion can be monitored separately for each chuter.

  • In the Single Mode, the one chuter setting is automatically selected, and ~ cannot be changed.

GAME DIFFICULTY As the number increases, the game play gets harder.

SOUND STEREO or MONAURAL. QSOUND is available with CAPCOM QSOUND cabinet only. For other cabinet, please set to MONAURAL. + STEREO - with QSOUND «+ MONAURAL - without QSOUND

DEMO SOUND With or without sound in Attract Mode. *ON-withsound = + OFF - without sound

CONTINUE Sets continuous play. ON: Continuous play is possible. OFF: Continuous play is not possible.

  • In the Tournament Mode, this item is automatically set to “OFF”, and cannot be changed.

START MODE Sets whether or not it is possible to start a one-player game from the twoplayer (2P) side after game start up. ON: Game can be started from the two-player (2P) side. OFF: Game cannot be started from the two-player (2P) side.

  • In the Tournament Mode, this item is automatically set to “ON”, and can not be changed.

MONITOR FLIP Turns over the screen. If the screen appears upside down, change the setting. + ON - with turnover + OFF — without turnover

EXTEND PLAY This feature sets whether tournament winners will receive bonus credits or not. + OFF - No bonus credits awarded (game over). + 2-5 — The winner can continue playing the game. (The number indicates the maximum numbers of games the same winner can play in a row.) + EVERY — The winner receives a bonus credit and can play the game continuously.

FACTORY SETTING To return to the factory setting, select this item and push the 1P START button.

EXIT To store changed settings and return to the TEST MENU, select this item and push the 1P START button.

Page 17

STARTING UP THE TOURNAMENT MODE: SUPPLEMENT |

  • The following is a simplified explanation of the flow of the starting procedure.
  • Connect the four units with the communications cables correctly and switch on the power.
  • The “TERMINAL CHECK” is displayed for a few seconds. TERMINAL TERMINAL CHECK CHECK
  • By pressing the test switch during this display, the settings can be changed individually using the test menu. (It is not possible to change the settings for the entire tournament on a single individual unit.) “EXIT” will cause the Terminal Check to return.
  • ID numbers 1 through 4 will be assigned. (“ID1” will be recognized as the “master”, and the others as “slaves”.)

** The demonstration will start.

  • After the ID numbers have been 1 assigned, when the test switch is pressed | «——TEST-SW on any of the units, all four units will ' enter the test menu. Demonstration Demonstration Demonstration Demonstration

TEST MENU TEST MENU TEST MENU TEST MENU

  • The settings (game difficulty, charge per play, etc.) for the entire Tournament can only be changed on the “master” monitor. Master

Slaves

  • If the test menu is exited by selecting “EXIT” on any of the monitors, all four units will simultaneously return to the Terminal Check.
Page 18

STARTING UP THE TOURNAMENT MODE

By using communications cables to connect four circuit boards, it is possible to play this game as a “Tournament Battle”. After making the settings correctly in accordance with the separately explained COMMUNICATIONS CABLE CONNECTION PROCEDURE, set the game mode to “Tournament”. The Procedure for starting up the Tournament Mode is as follows:

  • Connect the communications cables correctly. (Refer to the separately explained COMMUNICATIONS CABLE CONNECTION PROCEDURE.)
  • Switch on the power to the four individual units. (No special sequence required.)
  • “TERMINAL CHECK” will be displayed on the screens, and then, after a few seconds, ID numbers will be assigned to the four units. (“ID * OK” (* : 1 ~ 4) will be displayed on each of the screens.)

*By pressing the test switch during this Terminal Check, the test menu will appear and the various individual settings can be made. (It is not possible to make the settings for the entire tournament on a single individual unit.) *The Terminal Check will not end until all four monitors have exited the test menu. **If the Tournament Mode will not start up, check to confirm that the communications cables are connected correctly. If the Tournament Mode still will not start up, contact your dealer.

  • After the Tournament Mode has started up, if the test switch on any of the units is pressed, all four units will simultaneously enter the test menu. *The settings (game difficulty, etc.) for the entire Tournament Mode can only be changed on the unit assigned the ID number “1”. *Completing the test menu by using “EXIT” will cause the Terminal Check to return. (Return to the Terminal Check is possible from any of the units.)

*If any of the four- monitors is being operated in the Single Mode, it will not be possible to enter the Tournament Mode. Press the test switch and reset to the “Tournament” mode, and then repeat the Terminal Check.

CAUTIONS CONCERNING THE COIN LOCK

In the Tournament Mode, after all entries have been received, the “coin lock” goes on to prevent any further coins from being inserted. (When a game has ended, the coin lock goes off.) If more than one coin is required to receive one game credit (ie.: putting in two coins to receive one credit), the coin lock will go on when one credit’s worth of coins have been inserted and the game has begun. To avoid malfunctioning, please do not repeatedly insert coins one after another.

Page 19

COMMUNICATIONS CABLE CONNECTION PROCEDURE

. Confirm that you have three communications cables and one return connector. . Line up the four units to be used for the tournament. . Insert the return connector into the black terminal on the back of the first unit. . Insert the gray-marked end of one of the communications cables into the gray terminal of the first unit and the black end (no mark) of the same cable into the black terminal of the second unit. . Connect the other units in the same way. . The gray terminal of the fourth unit is not used.

  • This completes the connections. PwnNe

nun

eCONNECTION DIAGRAM

4 3 2 1

=] — i= Ee € —J a O a O a O a O

t m i I i ee) ee |

Communications cables Retum connector

Page 20

CAPCOM’ USA

3303 Scott Blvd. Santa Clara, CA 95054 TEL (408) 727-0400 FAX (408) 496-5720