Blasted Preliminary Parts and Operating Manual (April 1988)
Blasted (Bally Midway, 1988) · Parts & Operating Manual · 43 pages · 42 sections · original scan
MANUAL NO. OFO9-00300-0000 GAME NO. OFO9
10601 W. Belmont Avenue Franklin Park, Illinois 60131 U.S.A. psc (312) 451-9200 Fax No.: 312-451-4150 Cable Address: MIDCO = Telex No.: 72-1596 April, 1988
THIS GAME MUST BE GROUNDED. FAILURE TO DO SO MAY RESULT IN DESTRUCTION TO ELECTRONIC COMPONENTS.
ELECTRICAL BULLETIN: FOR ALL APPARATUS COVERED 8Y THE CANADIAN STANDARDS ASSOCIATION (CSA) STANOARO C22.2 NO. 1, WHICH EMPLOYS A SUPPLY CORD TERMINATED WITH A POLARIZED 2-PRONG ATTACHMENT PLUG
ATTENTION: POUR PREVENIR CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR. UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT. SAUF Si LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT
PUBLISHED BY:
MIDWAY.
TECHNICAL INFORMATION DEPARTMENT
GENE M. WILLIAMS, MANAGER RON WRIGHT, TECHNICAL WRITER DUANE KRUSE, TECHNICAL ILLUSTRATOR
SCOPYRIGHT MCMLXXXVIIE BY BALLY MIOWAY MFG CO ALL RIGHTS RESERVED
NO PART OF THIS PUBLICATION MAY BE REPROOUCED BY ANY MECHANICAL. PHOTOGRAPHIC, OR ELECTRONIC PROCESS, OR IN THE FORM OF A PHONOGRAPHIC RECORDING, NOR MAY IT BE TRANSMITTED, OR OTHERWISE COPIED FOR PUBLIC OR PRIVATE USE, WITHOUT PERMISSION FROM THE PUBLISHER. THIS MANUAL |S FOR SERVICE USE ONLY, ANO NOT FOR GENERAL DISTRIBUTION. FOR PERMISSION REQUESTS, WRITE: GALLY MIOWAY MFG, CO., 10601 W. BELMONT AVE., FRANKLIN PARK, (L 60131
THE INFORMATION IN THIS MANUAL IS SUBJECT TO CHANGE WITHOUT NOTIFICATION.
Printed In USA.
SECTION 1
SYSTEM INFORMATION
1-1
SAFETY
The following safety hints apply to all game operators and service personnel. Specific warnings and cautions will be found throughout this manual where they apply. Ba/ly-Midwa recommends that you read this page, and also, all of Section 1, before preparing the game for play.
WARNINGS
AC POWER CONNECTION - Before connecting the game to the AC power source, verify that the "Line Voltage Selection Chart" jumper wires are installed correctly tor the line voltage in the area. For additional information, refer to the Cabinet Wiring Diagram in Section 3.
HE - Service technicians and players can receive an electrical shock if this game is not properly grounded! To avoid shocks, DO NOT plug in the game until it has been inspected and properly grounded. Baliy-Midway games should only be plugged into a grounded 3-wire outlet.
The games control panel must also be properly grounded to protect the service technician and player from electrical shock. After servicing the control panel, check and ensure that the ground wires are connected before locking up the game.
DISCONNECT POWER DURING REPAIRS - To avoid electrical shock, disconnect the game
from the AC power source before removing or repairing any component in the game.
When removing or repairing the TV Monitor, extra precautions must be taken to avoid electrical shock. When the Monitor is initially turned off, high voltage still exist within the Monitor circuitry and CRT kcsthose-cey tube). DO NOT touch internal components of the Monitor with your hands or metal objects! Always discharge the second anode from the CRT before servicing this area of the game.
To discharge the CRT, attach one (1) end of a large, well insulated, 20KV jumper to ground. Momentarily touch the free end of the grounded jumper to the anode by sliding it under the anode cap. Wait two (2) minutes and discharge the anode again. USE THE PROPER FUSE - To avoid electrical shock, use the replacement fuse which is specified in the parts list for this game. The replacement fuse(s) must match the original fuse(s) replaced in type, voltage rating and current rating.
HANDLE FLUORESCENT TUBE & CRT WITH CARE - When a fiuorescent tube or CRT is
lisaifee it will break and may implode! Shattered glass can fly eight (8) feet or more from the implosion.
CAUTION
PROPERLY ATTACH ALL CONNECTORS - Ensure that the connectors on each printed
circuit board (PCB) are properly connected. If they do not slip on easily, . reversed connector can damage the game and void the warranty. All connectors are keyed to fit specific pins on each printed circuit board.
1-3
POWER
CHASSIS
ASSEMBLY
id w = ° a
TEST BRACKET
Test —-—+-—— PoT | CREDIT
CONTROL
PANEL SWITCHES TV MONITOR FIGURE 1 - ELECTRONIC GAME BLOCK DIAGRAM
GAME DESCRIPTION
"ROBOTS REVOLT... City Held Hostage" The above headline, splashed across the front page af ’The Daily + lets the player knaw at a glance just exactly WHAT he’s getting Below the headline a photograph of ane of the "Killer Cyborgs" stares menacinaly at the player. The player’s mission: Ta "Destroy All Cyborgs »..before they destr-y YOU!"
The player assumes the role cf an ‘Urban Guerilla’ Scrapheap City of the ’Mechanical Menace’ tawnsfalk. sworn to rid that is terrorizing the
Unfortunately, the local papulaticen is ’caught in the middle’, since all af the explosive battles in this classic confrontation take place in the very offices, factories and apartment buildings in which the townsfolk Live and work! Using the telephots scape on his Hi-Intensity Laser Fifle the player quickly scans the opposite side af the street far any sign ef the ’Technelogical Threat’; blasting into oblivicn anything that moves. (... often ta the dismay of the building’s human « pantS.ee Still, major property damage is a small price te pay for a world free of 'Tin Terrorists’!)
I. One ar Two player simultaneous play:
Players can "TEAM UP" ta destray the common enemy & progress faster... OR Players can campete ta see whe can Destroy the most Cyborgs!
lI. Each player has BOTH a wide-angle view AND a telephota (gunsight) view of the opposite side of the street. Enables the Player to 'see’ the action thru the eyes of his character.
III. Players can earn additional energy by blasting any “Power Scurces" (Table lamps, TV sets, wall clocks, etc.) they happen to stumble across! This additional bit of mayhem produces some delightfully nasty results... some players find shocting up the town just as entertaining as trying ta save it!
IV. Separate coin chutes enables players ta "JOIN THE ACTION" at any time as well as allewing players to "build up’ their reserves with multiple ccins.
POWER-UP TEST MODE
This test sequence is designed to effectively locate and identify any malfunction on the SOUNDS GOOD P.C. Board. Test results are indicated by an L.E.D. located on the sound board.
On power-up, under normal operation, the sound board runs through its self-diagnostic checks, flashing its L.E.D. to indicate each successful test. At the end of the diagnostic test, the attract mode begins and the game is ready to accept coins.
If one of the tests fails however, the L.E£.D. will not flash for the failed test nor for any remaining tests in the sequencial run. At this point, "SOUND BOARD INTERFACE ERROR" appears on the screen.
The following is the Self-Test routine for the SOUNDS GOOD P.C. Board
lst FLASH ~ Determines if the ROM (U7) is good. 2nd FLASH ~ Determines if the ROM (U8) is good. 3rd FLASH ~ Determines if the ROM (U17) is good. 4th FLASH - Determines if the ROM (U18) is good. 5th FLASH ~ Determines (f the RAMs (U6, Ulé) are geod. 6th FLASH ~ Determines if the PIA (6821) (U9) is good -
SELF-TEST MODE
The Self-Test mode is a special mode for checking the game switches and computer functions. It is the most complete way of checking the proper game operation and is quite easy to use.
The Self-Test mode may be entered at any time and from any mode of operation. Simply locate the black slide switch on the test bracket inside the coin doory
Slide it to the Self-Test position’ The game will enter the Self-Test mode
immediately and display the following test menu....
- SELF ~ TEST » SuitcHes & Seunos . CAME STATS . GONVERGENCE GRID
- OIF SwrttHey . GAME STATS RESET— and operate The Coin doors 1 Tilt (Stam) switch :
6.
USE PLAYER (1's CONTROLS , MevE THE CURSOR (Pow)
USING THE JOY ST? Ci. PRESS THE FIRE BUTTON B/OR THE CREDIT/ SERVICE PUSHBUTTON SWITEH TO ConTrnve.
- SELF (DIAGNOSTIC) TEST: This test is designed to effectively locate and identify any malfunction of the on-board computer. When selected, the game enters this mode immediately and begins scanning the memory stored in ROM (Read Only Memory) and RAM (Random Access Memory. If the test is
successful, at the end of the scan the test menu is displayed on the
_— streem If a defective component is found during the scan, that component . (the self? and its location will be displayed on the screen. The entire test is tnitial Testis performed in approximately 15 seconds. To exit this test, afterthe Freground cute din and background (power —up) test portion’ is completed, operate tHe Ti/tswith, the oo onedat the swirc# TEST:
- SWITCH AND SOUNDS TEST: The SWITCH portion of this test is designed to confirm the operation of player input switches and device switches in the game. When you enter the test, the screen displays acthing which indicates al( switches are open. When any Suitch i's
activated (the surtep is closed), the name of thet
switch will appear on the screen.
The SOUNDS portion of this test will cause a unique sound to be emitted for every switch that is manually activated in the game except for:
- TILT (Slam) Switch
- Option DIP-Switches (Dual-In-Line Package) To exit this test, operate the Tilt switch.
3, GAME STATS TEST: These game Statistics are avarleble Ky
your use in conducting time Studies. To exit this test, operate
the Tilt switchs ;
- CONVERGENCE GRID DISPLAY: This test is designed to display a crosshatch pattern used in adjusting the color monitor. This pattern may be used to adjust convergence, color balance, vertical linearity, and vertical /horjzontal size. To exit this test, operate the T/[t switch.
- OPTIONS SETTINGS TEST: All game options are adjusted through the use of DIP-switches located on the 68000 VIDEO BOARD. When this test is selected, a full display of the current DIP-switch settings will appear on the screen (see Figure 2 on page 1-7). To exit this test, operate the T7/t sur teh.
- GAME SrATs Reser TEST: The game statistres ava lable fer
your use tn the GAME STATS TEST can be reset by entering
tars test. After the Game Stat Reset message 0s de splayed
on the Screen, the fastimenu is de splayed wth the curser position at ‘SeLF TEST.
FiGuRE 2. BLASTED 2 PLAYER UPRIGHT
OPTION SWITCH SETTINGS
PART NO. MO51~00F09- A007
DIP SWITCHES:
COIN OPTIONS
1 COIN / 1 CREDIT 1 COIN / 2 CREDITS 2 COINS/ 1 CREDIT 2 COINS TO START / 1 COIN TO BUY-IN?
OIFFICULTY LEVEL:
HARD MEDIUM EAS
DOLLAR BILL:
REGULAR COIN DOOR COIN DOOR W/ 8 ACCEPTOR
ATTRACT SEQUENCE SOUNDS:
SOUNDS NO SOUNDS
NO RACK ADVANCE RACK ADVANCE
VIDEO FREEZE MODE:
NORMAL VIDEO FREEZE VIDEO
NOT NOT USED | USED
- BUY-IN FEATURE: WHEN THE PLAYER IS DISABLED DURING GAME PLAY, WITH NO CREDITS REMAINING, HE OR SHE CAN CONTINUE GAME PLAY BY INSERTING ONE
- COIN WITHIN A BRIEF, SET PERIOD OF TIME. IF THE PLAYER DOES NOT, THE GAME WILL END.
-ADDITIONAL NOTES:
- FACTORY SETTING: ALL DIP SWITCHES SET IN THE “OFF" POSITION. ~ THE QUAL-IN-LINE PACKAGE (DIP) OF SWITCHES "SW2" IS LOCATED ON THE 68000 VIDEO BOARD AT POSITION “A13". 1-7
FIGURE 3. VIDEO BOARD REFERENCE DRAWING
FOR 68000 SYSTEM es ON eee SO ees oo J2 J3 J4 J5 coo
OPTION SWITCH "2" o— (10 POSITION) os
co
cco
cm [on | co 68000 VIDEO GAME BOARD os
A084-91871-AFO9 084-91871 eee tH COMA KMRH ROWDY
When the trapped coin is not returned when the wiper lever arm is actuated, you may have an acceptor that is (1) ‘jammed’ by a slug, (2) ‘gummed! up with a liquid, (3) a ‘jammed’ coin, or (4), mechanical failure of the acceptor mechanism. In this case, first check for the slug that will generally be trapped against the magnet. If a siug is found, simply remove it and test the acceptor. If the chute is blocked, remove the acceptor and remove the ‘jammed’ coins. {f there is actual failure of the acceptor, remove the unit and repair it as indicated by the acceptor manufacturer’s service procedures.
When the coin is making its way through the pees and falls into the coin box, yet there is still no credit game awarded, there is either a mechanical failure of the coin switch, or an electrical failure of the coin and credit circuits. The first place to begin is by checking the coin switch. Most of these switches are of the make/break type of micro switch. The micro switch should be checked for continuity between the "NO" (Normally Open), "NC" (Normally Closed) and "C" (Common) terminals.
When the coin switch is at its rest position, the "NC" and "C" terminals should be closed and the "NO" terminal should be open. When the coin switch is actuated, the "NO" and "C* terminals should be closed and the "NC" terminal should be open. If the coin switch checks good, inspect the solder connections to the coin switch terminals to be sure there is good contact at this point. If necessary, use a continuity tester or meter (VOM or DVM) to check from the terminal \ug on the switch to the associated P.C. board trace. This will verify whether or not there is continuity to the credit circuit. However, if the coin switch wires check good, the problem is in one of the game logic printed circuit boards that contain the coin and credit circuitry.
When the player deposits a coin or token and it is accepted, but the game will not start wnen the Credit/Start button is pressed, there may be a probiem in the Credit/Start button switch, the interconnecting wiring, or the game logic boards. First, check the switch. Most of these switches are of the make type of push-button switch. If the switch is OK, proceed to check the wiring. Again, make sure to go from the terminal lug on the switch to the P.C. board trace. This way, you will check the terminal contact as well as the P.C. board circuitry. If there is no continuity, check each section of the wiring, until the open or break is located. If the wiring is OK, the problem must lie in the game logic boards.
TRANSFORMER & LINE VOLTAGE PROBLEMS
This game must have the correct line voltage to pi hatin properly. if the line voltage drops too low, one (1) of the game logic board circuits will disable the coin/credit circuit. The point at which the games’ logic circuits will fail to function is approximately 100 VAC if the voltage supply is 120 VAC or approximately 190 VAC if the voltage supply is 220 - 240 VAC.
Low line voltage can have many causes. Line voltage normally fluctuates a certain amount during the day as the total usage varies at the location. Peak usage times occur mainly at dawn and/or dusk. Therefore, if your game's problems seems to be related to the time of day, total usage may be a factor to be considered. A large load connected to the same line (voltage supply) as the game, such as a large air conditioner or other device with an exceptionally large electric motor, will drop the line voltage significantly when starting up. This drop in supply voltage can result in an intermittent coin/credit problém. in addition, poor connections in the location's wiring, plug, or line cord can also cause a significant drop in power. Cold solder connections in the Pace wiring, especially in an areas like the transformer connections, the interlock switch (it applicable), and the fuse block, can also produce the same results, although, probably, on a more permanent basis.
1-9
Some locations may have dimmer (rheostat) switch installed, and the game may be on the same line (supply Hc Obviously, the voltage available to the game is going to drop dramatically when the dimmer is turned down.
The correct way to check for proper line voltage is with a meter (VOM or Dv). Set the meter to a scale higher than the location's voltage and (use caution to) check the voltage at the wall outlet that the game is connected to. If it is OK here, check the game transformer primary wiring connections and line filter. If the location’s voltage is not present at the connections, examine the solder connections on the transformer, fuse block and interlock switch (if applicable). If the locations voltage is now present, the problem must either be in the transformer, cable connections, or in the printed circuit board power supply.
When you suspect the games primary transformer, check the secondary voltages with a meter set to the 50 VAC range and correlate the meter readings with the Power Supply Chassis Assembly wiring diagram. This transformer must also be properly grounded. Check the ground potential at the transformer, especially if there is a ‘hum bar’ rolling up or down on the Monitor screen. :
NO POWER, NO PICTURE - If the Monitor screen is completely dark, check the back of the Monitor to see if the CRT filament is glowing. Ifit is, try adjusting the brightness control. If this has no effect, listen near the Monitor for the high-pitched B + hum produced by the isolation transformer. When you hear the hum but there is still no picture, and you have tried adjusting the brightness, major Monitor servicing is indicated.
When the Monitor appears to be completely dead, check the game to see if power is available. If there is no power, check the wall outlet. If the wail outlet is OK, check the game fuses, the interlock switch (if applicable) and cable connections. Sometimes it is difficult to determine if a Slo-Blo fuse has blown. If in doubt, check the fuse with a meter set to any resistance range. If there is no indication of resistance, the fuse is blown or open.
CABLE PROBLEMS - Cable problems include shorting to metal components and
maifunctioning controls. The repetitive blown fuse problem can sometimes be quite exasperating to solve. (Where is it? I've checked everywhere.) Short circuits have the tendency to occur in areas almost impossible to find. The first thing to do in this instance is to install a known good fuse. Old fuses age and sometimes blow without any apparent cause. However, if the new fuse also blows, there is a short in the game and it is most likely to be a permanent type of short.
The best way to approach this problem is by disconnecting devices that may be causing the roblem, such as the TV Monitor, the various printed circuit boards (one at a time), and the isolation transformer. Disconnect the devices by FIRST turning the game off and then disconnecting it from the wall outlet. Next, remove the blown fuse and connect a meter across the fuse Bor terminals (this will save blowing a fuse each time you check the circuit when the game is on).
Set the meter to any resistance range. The meter should indicate a shorted condition exist. If there is no meter indication, the probable suspect is a component that shorts out after it has heated up (we'll cover this in a minute). Therefore, assuming you are reading a short on the meter, disconnect the components fram their cabling one at a time, checking the meter after each one is disconnected. When the short disappears, you have disconnected the bad component.
\f all components are disconnected and the short still remains, the problem is in the cabling and only patient ay oeepat will reveal its location. Carefully examine all the wiring, looking for terminals that may be touching, metal objects such as coins shorting the connections, or burned cable insulation. If necessary, use the meter to check each suspected wire. 1-10
It is assumed at this time that you have connected the meter across the fuse block terminals as stated above and you did not read a short. This most likely means that you have a component somewhere in the game that only goes bad after it heats up. The component can check good when its cold. In this case, turn the game off and disconnect all of its socketed components. Install a known good fuse in the fuse biock and turn the game on. If the fuse does not blow after a few minutes, the cable is not the problem. (In this instance it shouldn't be, actually, but it never hurts to check.) Next, turn the game off again and reconnect one component. Turn the game back on and wait a few minutes to see if the fuse blows. if it does not, turn the game off again and reconnect another (single) component.
Turn the game back on and wait a few minutes to see if the fuse blows. When the fuse blows, the last component connected has the part on it that is going bad after it heats up.
MALFUNCTIONING CONTROLS - The most common problem here is a bad POT
(potentiometer). Typically, a bad POT will cause the image on the screen to jump when it reaches a certain point. The only cure for this is to install a known good POT.
When a feature is operated by a switch (for example, joysticks and contral panel
push-buttons) does not operate at all, check the switch with a meter or continuity tester to verify its operation. If the switch does not check good, replace it. If the switch is OK, suspect the switch input from the printed circuit board. In this case, refer to the wiring diagrams and printed circuit board schematics and check to see what type of input is supposed to be at the switch. In many cases, the input will be +5 VDC. If so, use the meter to check for its presence with the game turned on. Normally, the switch is used to ‘pull’ the +5 VDC line low (near ground) or to ‘pull’ a low line high.
if the printed circuit board output is missing, check the wiring from the printed circuit board to the output device. If the signal is at the printed circuit board trace, the wiring or connection is at fault. If there is no signal at the printed circuit board trace, begin exploring the printed circuit board using the logic schematics.
1-11

This page is a drawing, shown as the original scan.
Te
HWVUOVIG ONIYIM LINIGVD 2 SOLLVWGHIS “SLNOAWT LNANOdNOS
€ NOILO3S
TO <OPTIONAL) BILL ACCEPTOR = C1iSVAC) TO_MONTTOR YY. <tisvac> i>
POWER CHASSIS A945-80059-8200
@BLU-ORN
° =] z z cy ‘J ONOTL OM
is
>) fe Zz
- |= z S| |= cs) a} {tz i at lz z al iz & al [a a a |e a
7] i { t
ae
GRN-YEL
La... POWER SWITCH
LINE VOLTAGE SELECT: CONDOR SHITCHING TO COIN DOOR CONN. POWER SUPPLY
Ji tyac HoT 31AC NEUT
}@017-80003-0543
TON CHART Fiev_RTNI Fieve +1evt tev GROUND} GROUND! GROUND! GROUND! GROUND! 18 GROUND! at GROUND H 12) GROUND H 13 TO OPTIONAL ORN-BLK LAMP DIRVER_BD
GRY-BLK__ GROUND GROUND GROUND GROUND GROUND, GROUND.
HHT-BRN GROUND LAMP DRIVER
PLAYER 2 UP,
PLAYER 1_UP, PLAYER 1 RIGHT
PLAYER 1 DOWN,
PLAYER 1 LEFT.
PLAYER @ RIGHT
PLAYER 2 DOWN,
PLAYER @ LEFT, LIGHT 1 CNTL, TO CONTROL CONN.
TO_<OPTIONAL?
TO COPTIONAL) CABINET START LIGHTS AND SHITCHES ——>
To COIN DOOR
GROUND H 14 +5V1 15 +5V1 16 +5V1 17 +VI 18) +5V1 19) +520 RED +5¥
TO COIN DOOR METER Ip
TO_ AUDIO AMP BOARD
TO SOUND GOOD BOARD
TO 68008 BOARD_JS
VOLTAGE ; 105 ; 115 216 | 220 1 248 ; COLOR JUMPER 1| 5-8 | S-1i] e-14]11- JUMPER 2[14-15] 14-15 MONITOR
BALLAST Jumper 3! 4-7 T 4-16 4-7 | 4-7 14[11-14]11-14]a0RN our _| out | out | out [aver 4-10! 4-13 @RED RED 21GREEN 31 BLUE 4 4 GROUND sivs¥Nc BLK-HHT, BLK-ORN WHT=BLK WHT-BLU WHT-YEL WHT-GRN. GRN-RED GRN-YEL,
ret opéa opét opé3 ores
1@ GROUND 11] GROUND In ~TGROUND ‘GROUND i+5v iesv ikeY iRESET_OUT GROUND te1ay 6880 VIDEO GAME BOARD 9884-91871-F 008
101GROUND oPsi ops2
WHT-BLK HHT-BRN HHT-RED HHT-ORN GRY-GRN GRY-ORN TO POHER CHASSIS aBLK «1isvac> SN DATA @ ‘SN DATA 1 SN DATA @ SN DATA 9 ‘SN_RESET ‘SN STROBE
SOUNDS GOOD RD. HHT-BRN BRN H YEL i
GROUND METER-RET GROUND I 22
revit GROUND I2 GREENI3 GROUND! 4 BLUEIS| GROUND! keviz HBLUK~i 8 YBLNK~{9 sell treet” Ipait Ipaa! 1pe3} 1Pe4! Ip@si Ipasi 1pe7! GROUND! 1P10110 rriitit 3pi2i12 1P13113 kevii4 1P14115 1P15116 1P16117| Ipi7iie GROUND!19 WONAKAOD METER
BRN-HHT BRN-BLU BRN-YEL BRN-GRN ‘BRN-BLK GRY-WNT TO MONITOR
TO <OPTIONAL> DGLLAR DOOR CONN.
To COIN DOOR CONN.
TO SOUNDS 600D BOARD > SH STATUS) HHT-RED. WHT-YEL
RED-BLK RED-HHT SERVICE
To TEST PLAYER 1 BRACKET PLAYER 2 BUTTON, RED-BLU (OPTIONAL )STARTI RED-YEL_COPTIONALDSTARTE,
TO CONTROL,
- = 18AHG 3e0V COHN.
@ = 18AaHG 6e0V
NOTES?
STERN 4715788 BALLY MIDHAY HFG. CO.
BLASTED CABINET HIRING Dyed N@51-00F@9-Age3
SHEET 1 REV oF @
TO POWER SUPPLY {VOLUME CONTROL | To 6800@ BD. J2 t SOUNDS GOOD BOARD GROUND YEL
Aa84-91863-Be00 3 1a GROUND VOL POT WIPERIT fa sRouND aupto ouT!2 1+5¥ AUDIO OUT! 1454 GROUND! 4 i+1av A GROUNDIS tetev AUDIO OUTIS f€ GROUND AUDIO OUTI7 A GROUNDI8 kevis VOL POT Al1e H @ GROUND! 11 — (Mi2ie GROUND = VOL POT BIi12 DUAL POHER AMP A084-98918-H00 COIN DOOR LIGHTS fvevRTN
TYPE GE194 TEST wnT-vet }— SERVICE \ut-reD | L_,) H
TEST BRACKET TO_POWER SUPPLY rT —
N= = ORN-BLK isk ‘ORN-BLK GRY-BLK GRY-RED ONO SOD
HHT-BLK
BLK-ORN
GRY- GRN
COIN METER aYEL J a
To 68e@@ BD J3
To_68000 BD J2 ls BRN-WHT.
GRY-GRN BLK BRN-BLU “BRAIDED a Bit. SHIELD 4tKEY sy RETURN 61R. AUDIO 71R, SHIELD _B}¥. AUDIO an one
BRN-BLK
Cy r a eT | SN_STROBE GRY-ORN "SN DATA 1 HHT-BRN SN DATA @ WHT-BLK SN_STATUS GRY-WHT SN DATA 3 HHT-ORN SN DATA & WHT-RED
SN RESET
TO 68680 BOARD J4
TO 68000 BOARD J2
CONTROL SHELF WIRING AND WIRE SPLICE TO POWER SUPPLY SAME COLOR WIRES
BLK-YEL PLAYER 1 UP BLK-WHT PLAYER 1 DOWN
TO 680@@ BOARD J3 BLK-ERN 1 PLAYER 1 RIGHT
BLK-ORN PLAYER 1 LEFT
RED-BLK PLAYER 1 TRIGGER RED-BLK iit BRN 4
| TO 68@a0 BOARD J2 | WHT-BLK | PLAYER 2 UP. | VEL | tot YeL |
t DUAL LAMP DRIVER AB88-91951-Aee0 PLAYER 1 BUTTONS
FOR OPTIONAL DOLLAR ACCEPTOR PLAYER 1 LIGHT frp REPGRN_| PLAYER 2 LIGHT {2B PLYR 1 START SH {3B O— Te PLYR 2 START SH 14#—— +12V GROUND *#ORN-BLK EL GND.
‘J GROUND vec KEY CONTROL 1 cou 1 CONTROL 2 coL 2
| WHT-BLU | PLAYER @ RIGHT | —42 5 |
MHT-YEL, PLAYER 2 DOWN
HHT-GRN PLAYER 2 LEFT
| RED-HHT. | PLAYER 2 TRIGGER | RED-HHT. | i BRN |
YEL GND Cee i YEL
PLAYER 2 BUTTONS hesecteeniicacicctenaracicacamennaad CI TO 68098 BOARD J2 TO 68888 BOARD J3
GRN-RED
LAMPS AND SHITCHES LOCATED ON GAME CABINET
ORN-BLK Fy ORN-BLK FOR OPTIONAL © BOLLAR ACCEPTOR PLAYER 1 LIGHT RED-GRN PLAYER @ LIGHT t2—-YeL-GRN MARS ELECTRONIC RED-BLU PLYR 1 START SH BILL ACCEPTOR RED-YEL PLYR 2 START SH ORN-BLK +12v GROUND ner GRY-BLK 1. GRY-RED fo8
WHT. WHT WHT-YEL q] COIN NETER 11evac_NEUT 11@VvAC HOT
TO 68808 BD J3
TO_68000 BD Je DONO UD 1 NOTES? t BALLY MIDWAY MFG. CO. CoqH tH, BRN-YEL D._STERN Senses # = 18 AlG 3e0v 4715788 BLASTED 18 PIN INTERFACE CONNECTOR fictee J: CABINET WIRING (NO CONNECTION FOR $1 BILL Ne51-00F @9-Age3 ACCEPTANCE >
SHEET @ OF @ [REV
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
DESCRIPTION
18 pF AX CR 18pF AX CR 33pF AK CR 47pF AX CR 68pF_AX CR 18BpF AX CR 398pF AX CR 82BpF AX CR +BluF AX CR 1BuF AX TANT 47BuF RO ELEC 18 OHM 1/4W 5X RES 22 OHM 1/4W 5X RES 47 OHM 1/4W 5X RES 68 OHM 1/4W 5X RES @2 OHM 1/4W 5X RES 198 OHM 1/4W 5x RES 288 OHM 1/4W SX RES 478 OHM 1/4W SX RES 518 OHM 1/4W 5X RES 568 OHM 1/4W 5X RES 688 OHM 1/4W 5% RES 1K OHM 1/4W 5X RES 2K_OHM 1/4W 5X RES 2.7K OHM 1/4W 5X RES 4.7K QHM 1/4W 5X RES
18K OHM. 1/4W 5% RES 28K OHM 1/4W SX RES 1K_9 PIN SIP 4.7K 9 PIN SIP 4.7K 18 PIN SIP 198k 19 PIN SIP 1N4148 DIODE 2N4123 NPN XSTR MPSA7@ PNP XSTR TIP118 NPN XSTR COSC 16MHz COSC 28MHz
74F BS 74F32 T4E74 7AFBE 74F157 TAF 174 TAHCT244 74584 74874 74LSBe 74LSB2 74LS85 74ALSBB 7ALS28 74LS32 74LS74 74LS86 TALS148 7A\S153 7ALS157 74LS161 7418163 74LS169 74LS173 74LS174 T4LS175 7ALS194 74LS244 74LS8245 74LS258 74LS273 74LS283 74LS298 74LS368 74LS374 e
ae DAVE VOWNTDOUUOMAWUOANUANAY
OE NN ON NN DEAE RUN ONE NUN OE EE EEN RE ERNE NEE EEN NNR DESIGNATION
c71 css C72 C37 €38 C73 C75 cs1 C74 C45-C5e C39 CS3 C54 C76 C77 C2-c33 CP1 CP2 C35 C42 C4@ C41 C43 C44 C56-CE9 C36 C52 CPt7-151,153-1681 Cl C34 c7e CP3-cP6 R79 RBG RBZ RSS RBS REE R52 R57 RIZACPART OF MOD.) R47 R4B RAD RS@ R53 RIT R6G R96 RO7_R12H R121 R123 R92 R9S-R11Z2 R56 R64 RIB R1II7-R119 R122 RB1l RBA REF R68 R71 R75 R76 R77 R78 RSS R1 R3-R6 R1Z RE7 R7BR7Z RTA REG REI R73 R45 R46 R114 RIS R2 RB R11 RS1 RS4 RSS RSI R61 REZ REZ RES RBS REI R91 R93 R94 RIS R113 RIE RQ RIB RIZ-R4A R? RM7 RMB RMS RM1Z RMI RMG6 RM2 RM3 RM RMS D1 oz ol a3 Q4 Q5 Q6 07 08 a3 Q2 ais
iF 1A 12H LIF 8K 3G 19D 1K 2F 1H 13C 13K 14G 13F 136 SK 12K 14A 9A SA 13A 155 15C
SB 9c 2E—
130 18E 15A 14D 139 15G 149 18F 148 14c 120 7K 3K 118 128 BA 7A 4K 4H 3H 2H 1H 2G 4G 6G 6H OF BF 6F 7F 6k 138 88 15H 13H
8G 9H 7H 186 9G 7G 8H 18H SH 11A 12F 30 SE 90 188 12C 11C 11K 184 6A 11G 126 78 68 1G SE GE 7E BE 6C 7C BC SC PART NUMBER
8368-88828-2838 8365-888905-2826 8386-98888-83BG 9986-98880-2859 B36B-BG820-B828 8368-98880-2046 8986-28888-3088 B945-88816-9428 8986-988865-2998 8986-88858-2795 8875-88883-888\ 188€-28985-8811 1B8E-8888S-B8816 188E-88025-9825 182E -69885-9829 188E-69895-9831 18GE-82085-6833 182E-28205-B845 198E-88885-9251 18BE-88885-8853 1B88E-88885-B8854 188£-99525-9856 18BE-28885-9061 18GE- 88885-9068 188E-96855-9871 188€-98805-8979
18BE-89825-0888 188E-99895-B895 182E-g0884-9811 182E-88884-B024 162E-90804-5026 182E-90904-8845 183€-99902-8985 1G4E-88881-2087 184€-B8882-9012 184E-88883-9091 189E-98602-8881 8384-95684-8087 8986-298883-7689 BAS9-88883-8815 BAS9-88883-8881 GAS9-88883-B934 GAS9- 96883-2630 9384 -£9883-2059 GAS9-88883-9853 BAS9-88883-6831 BAS9-B8B803-BBG4 BAS9-86883-8885 9B75-88883-8081 B326-B9003-C62H BA15- 68883-8823 9384-9B003-9018 8986-88863-7488 BA15-88883-2811 9986-88883-7328 8986-88833~1884 B986-98883-6199 @986-88883-1865 8986-28883-9999 3A15-88283-0867 BA53-96803-8886 938 4-80883-B821 G986-88883-1863 BAS 9-88893-808 8204-88853-8823 BAS3-8G863-8809 939 4-88883-9024 8394-88893-9825 9384-88863-9826 8986 -B08G3- 4882 8986-90883-6408 8384-88823-9928 8S86-B88823-4728 638 4-88883-2032 GAS 9-B8883-2019 BAS9-88823-2811 9986-088883- 4685 68988 VIDEO GAME BOARD AG84-91871-F 888 M@S1-88114-F 165
DESCRIPTION
74L8377 PACOUT REV 1 PLA PACNS REV 1 PLA ROMCTRL REV 1 PLA MMCB2B HAL MMCB1A HAL MMCO6 HAL MMC@3B HAL COLARB PAL28L8 1ODCD PALI6L8 MEMOCD PALI6L8 DTACK PALI6R4 HSYNC PALI6R4 93419 64x9 RAM 2818 2Kx8 RAM 45nS 2818 2Kx8 RAM S5nS 2864 8Kx8 RAM 158nS 6116 2Kx8 RAM 158nS 6116 2Kx8 RAM 128nS MC6BB88 MC6a4o ROM/EPROMS 16 PIN IC SOCKET(.3) 28 PIN IC SOCKET(.3?
24 PIN IC SOCKET(.3) 24 PIN IC SOCKET(.6) 28 PIN IC SOCKET(.6) 32 PIN 1C SOCKET(.6) 64 PIN IC SOCKET(.9) AUTO INSERT PIN .825 AUTO INSERT PIN .845 FERRITE BEADS JUMPERS SWITCH PC MTG. DIP SWITCH 18 POS SNAP PC BOARD DESIGNATION
12E 11€ 50 60 SF 11d
14H 14F 1SF 14E
1E 18-38 1C-3C 73-183 11D 12D 1G 4K
- 20 2K 14K 14E 15E 110 120 14H 14F 15F 5G 5D 6D 7D 8D 9B 13E 40 18-48 1C-4C 110 12D 1E 4A 79-189 4E J2 03 94 JS J6 v1 FB1-FB18 OW1-JW12 PBL PB2 12A az aig PART NUMBER
GAS9-2B8H3-BG12 AS9A-26AXL-AXHD AS9A-26AXL-BXHD AS9A~-26AXL-CKHD @986-88883-9888 8986-88893-8988 8386-88883-9288 986-88893-9190 E61~-88883-9981 2B75-88893-88083 8B875-88883-9504 8875-88883-6285 BB75-88853-2086 8986-88883-9668 BAS9- 88883-8828 BASS-88883-9829 BA15-82883-2879 GA59-88883-2027 BA59-98883-8514 933 4-28803-8851 A15-888H3-B068 SEE _ROM/EPROM CHART 118E-88881-8893 118E-68881-8885
118E-28821-2889 118€-99981-2097 118E-88881-8818 118E-88981-9824 118E-88881-B216 9384-88884-2889 8384-80884-8010 8316-282804-8882 117E-89881-2983 8986-88884-3195 113E-88981-884 8817-99687-8134 ABSS-91871-ES8R
3-5
? ® ro cpu Ron
ExTRSTS. sveoses
ame aus oes extests BACKGROUND BACKGROUND FOREGROUND
SECTION
ra 1 pp? _svcoscs forte
? mOTEST mn lesa. PLousseRD| a ‘SEPT 20 1907] ALLY MiDUAY AFG, CO.
71 UL er 18) BE> nc68000
49a —© GyBLNK~. rost-ertaa9 SVBLNK~
cpurst~
UAH rte © eo up pisaae DOLLY MIDWAY HFG. CO. 60000 VIDEO GAME BeARD
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Rebbeee ” abbeheeds ” HbfAOA08 jae Ad Abe bet { sh 5
seeeaeeet shbbepee}
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
13xve nary (mnowsauos wacayg
3-10
3-11
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
3-13
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
+ 7406 FBS FBG IME_BASE 12) 12 1 pp 2 1 1 pp2 _HSYNC~ 1a ls a
GYBLNK
7406 CHPBLNK 9. [> eusies a3 ia 7
PAL2@L8A cents 24 as Ie vec he 1B mo omip 2a
| 12 00 (2 | 74LS174 | 28 | |
| 13 roi {24 | 1D 10 | 3A | |
| 14 102 22 | 2D 2a | 3B | |
| 1s 103h5 | 3D 30 | 4a | |
| 16 104 iF | 4D 40 | 4B | |
| 17 105 | sD SQ | ArB | |
| reat | Ee | oo ea | 5 |
| vine~ ut 11@ 12 “ | cL | sa |
[ GND 113 8B
9B
74L$157 1a 1B 1Y 2A 2B ay, 3A 3B 3Y 4a 4B 4Y ADDRESS
CONTROL,
G
NOTES? BALLY MIDWAY MFG. CO. R. A. PLOUSSARD SEPT 28 1987] 68008 VIDEO GAME BOARD
AG84-91871-F 808 MeS1-00114-F:166
SHEET 19 OF 19 [REV
3-15
3-16 sw
© i206 oarcy wowar ure. co ALL RIGHTS RESERVED PAT, PENOING cPe7 ——} C304 a9 te
i a fe a + 8 tr
Sg CP101 cP102 | [| cro oo cer {Oh
¢
en i &
CPIZ + —c 2 cPlS:
wW1 ———— Ro + tar ui3" a RIT
cpa
sw ws
U6
A080-9 1863-B000 SOUNDS GOOD
for Production REVISIONS
@alty | MIDWAY MFG.CO. FRANKLIN PK PROJECT ENG: C. MEDONICK [secon
ASSEMBLY DRAWING SOUNDS GOOD
A084-91863-B000 tL.
OIM. TOLERANCES | UNLESS SPECIFIED PART NO.
MOSI-O0O!114-B!1SO
DESCRIPTION
68 PF AX CER 10% 100 PF AX CER 150 PF AX CER 10% 270 PF AX CER 10% 390 PF AX CER 470 PF AX CER 10% 680 PF AX CER 820 PF AX CER 5600 PF AX CER 10% -O1 MF AX CER
0.1 UF AX CER 1 MF RD TANT 10 MF AX TANT 10 MF RD TANT 47 MF AX ELECT 100 MF AX ELECT 100 OHM 1/4W CRAN
180 OHM 1/4W CRBN 360 OHM 1/4% CRBN 1K OHM 1/4W CRBN 2.7K OHM 1/4W CRBN 3.3K OHM 1/4 CRBN 4.7K OHM 1/4W CRBN
10K OHM 1/4W CRBN
12K OHM 1/4W CRBN 18K OHM 1/4W CRBN 24K OHM 1/4W CRBN 33K OHM 1/4W CRBN 47K OHM 1/4W CRBN 82K OHM 1/44 CRBN 100K OHM 1/4W CRBN 120K OHM 1/4W CREN 150K OHM 1/4 CRBN 160K OHM 1/4W CRRN 330K OHM 1/4W CRBN S10K OHM 1/4W CRBN 560K OHM 1/4 CRRN
1N5817
2N5305
74.804 T4F 32 es NEN RB wWANMNONE
UNNNYNY SS
WENN NE
ENN ENN PENN NEE NY
N DESIGNATION
C3-C5,C8-Cl1 €111,¢301 €113,¢118 €1,C2,C191,C102 112,302 C303 C106 cé,C7 c1is 104,c197,c110 €116,C120,cP1-CP7, CP9-CP13 €304,C307 ,cP101 ,cP102 C103,C108,C114,C117 cP14,CP15 €119,C121 105 ,C122 cP16,C123 R17,R18,R25,R103, R202 R125 Ri23,R124 R10,R121 R122,,R126 R106 R1-R3,R6-R7 RI R12-R14 R4,R15,R16,R19-R21, R23 R101 R117 R105,R107 R113,R116 R26 ,R120 R109 R5,R22,R24,R118 R111,R112 R108, R115 R102 R104, R114 R110,R119 R127
03-04
Qi1-03
U13 ulé PART NUMBER
0307-00800-0011 0304-00800-0001 0307 -00800-0010 0307-00800-0009 0986-00800-3000 0307 -00800-0008 0358-00800-0002 0304-00800-0002 0307-00800-0007 0986-00800-2200
0986-00800-0200 307 -00800-0004 0986-00800-0700 9307 -00800-0005 0307-00800-0003 0307-00800-0006 100£-00005-0033
100£ -00005-0039 10CE -00005-0048 100€ -09005-0061 100£-00005-0071 100E-00005-0074 100£ -00005-0079
100£ -00005-0088
100E -00005-0090 100£-00005-0093 100E -00005-0097 100£-00005-0100 100E -00005-0104 100£-00005-0112 100€-00005-0115 100E-G0G05-0118 100£-00005-0120 100£ -00005-0121 100E -00005-0128 100E£-00005-0133 100E -00005-0134
103£-00003-0009
0360-00802-0012
0304-00803-0060 0304-00803-0059 A084-91863-B000 M051-00114-8151 Rev. 3
DESCRIPTION
T4S74 14584 /40106 6821 PIA 68000G8 CPU AD7533JN DAC SGO1RO PAL LM359 MC3340 RAM 2KX8 ROM/EPROM ROM/EPROM ROM/EPROM ROM/EPROM
FERRITE BEAD
16 PIN IC SOCKET 24 PIN IC SOCKET .300 24 PIN IC SOCKET .600 28 PIN IC SOCKET 40 PIN IC SOCKET 64 PIN IC SOCKET
AUTO INSERT PIN TIN .025 SQ AUTO INSERT PIN TIN .025 SQ AUTO INSERT PIN TIN .045 SQ ZERO OHM RES
GREEN LED SWITCH PC MTG 16 MHZ XSTAL OSC PC BOARD i
ror DESIGNATION PART NUMBER
ul2 vil u9 US uio UIs U2,U3 UL U6 ,U1S v7 us u17 vis
FB1,FB2,FR101,FB102, FB301 ICS W10 ICS U5 ICS U6,U16 ICS U7,N8,U17,U18 ICS U9 ICS US
Jl
J3
JW1-JW3
LED 1 Swi Yl 0304 -00803-0061 0304-00803-0056 0304-00803-0054 0304-00803-0051 0304-00803-0055 0E36-00803-0009 0304-00803-0053 0358-00803-0002 0304-00803-0057
SEE ROM/EPROM CHART
0316-00804-0002
110£ -00001-0003 110£-00001-0009 110£-00001-9607 110£-00001-0010 110£-00001-0011 LLOE-G66061-0615
0304-00804--0009
0304-00804 -0009
0304-00804-0010
117E-00001-0003
119£-00001-0001 0986-00804-3100 0304-00804 -9008 A080-91671-G000
3-17
a = @ Je = 18 PIN RAISE 21D reot-ygryga Ran_ROM,
an? 4 vee Key a oD extreset~ at el— 2D a ufp—L, REV 2 - Chonged sheet &. Cnn 9720706 REV 1 = Chansed sheet 2. CHM 074786
ro . MEDWICK BALLY MIDUAY AFG, CO.
HEELS
spare Gates nos _29[,,RceaeD mez —30|*t
sur ive _
Sres? Suton ree BALLY MIDWAY AFG. CO. Tree ‘SOUNDS G00D 19 JURE 8, a
BALLY AIDUAY HFG. CO. [SHEET 4 OF 3 [RW
anEcT
3-19
TOBUS 83g?
A07533 93d? pr RIBS Bie 72? Be OVREF
3B? 2NS365 S. 4 e2 $408
BS
My BS — ciai 4 18uF b7°ur my He aig
Af8s Cc
BL J3 - 12 PIN KK100
- __ J [P>s3 4
P>J3 8
PJs 11
ANALOG_OUT]
- 0193 ca
gig KEY J39
12v 2 RV12
8188 RY_SENSE P js31 aYBS RV_RETURN P js3 18
12DEC
RV_SENSE 2 RV_RETURN REV 1.8 6-26- 848° 6 R181 CHANGED TO 12k. CMM 3 [woTes: F
| J ens3e5 | anne | BALLY MIDHAY MFG. | CO. |
2k at
| + | t | [i PER | SOUNDS GoOD |
| t | 1 JUNE 86 | Ave4-91863-B000 |
cu e51-00114-B152 3-20
SHEET 5 OF 5S [REV
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
3-22 J2 R6 cP3
R8& i
UID
c10 c8 MCR/2 DUAL POWER AMP. PC. A080-909 10-HO0O DUAL POWER AMP A084~90910~HO0O M051-00986-HO17 (PAGE 2 OF 2) REV. 3
CROSS REFERENCE LIST
| DESCRIPTION | QTY. DESIGNATION NO. | PART NOS. | |||
| -002 MF RD CER. | 2 | C11,C12 | 0360-00800-0012 | ||
| Pa | «1 MF 50V AX. CER. | 6 | C7~-C10,CP2,CP3 | 0986~-00800~1100 | |
| 1 MF RD TANT | 2 | C1,C2 | 0875-00800~-0002 | ||
| - | 22 MF 6V RD TANT. | 2 | C3,C4 | 0986-00800-1600 | |
| 3 | 220 MF 25V AX ELECT. | 1 | cPl | 0986~00800-3200 | |
| 470 MF 6V AX ELECT. | 2 | C5,C6 | 0986-00800-1700 | ||
| 0 | 1 OHM 1/2W 5% | 4 | R5-R8 | 100E~-00006-0002 | |
| 27 OHM 1/4W 5% | 2 | R3,R4 | 100E~00005-0018 | ||
| g | 7 | 2.7K 1/4W 5% | 2 | R1,R2 | 100£-00005~-0071 |
S 5
| 0 | * MB3730 | 2 | U1,U2 | 0066~188XX~XX4Xx |
| TIN .045 SQ. PINS | 12 | J1,d2 | 0304~-00804-0010 | |
| HEATSINK ASSY. | 2 | HSA1,HSA2 | A986-00010-0000 | |
| PC BOARD | 1 | A080~90910~H000 |
- NOTE: THIS PART IS ACTUALLY PART OF THE HEATSINK ASSY.
RELEASED 5, JANUARY, 87. CMM 19 FEB. 87 ~ REV. 1 ~ Cli & C12 WERE AXIAL. CMM 27 APRIL 87 ~ REV. 2 ~ Cl & C2 WERE 4.7UF TANT. CMM 1 SEPT. 87 ~ REV. 3 ~ C1,C2 WERE PART #0B75~-00803~0002
= Released Be Pl deel. + REVISIONS
“© FULL |no.redd | PER @ily | MIDWAY MFG.CO.
ASSEMBLY DRAWING DUAL POWER AMP A084-909!10-HOOO provect enc: C.MEDNICK eee eee PIM TOLERANCES Tony OBS /1/18/86 a | HLL.
PART NO.
MO51-00986 -HO!O ConcentmciTy
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
BALLY MIDWAY’S BLASTED (2 PLAYER) UPRIGHT GAME #F09 ROM/EPROM LISTING
UNPROGRAMMED 68000 VIDEO BOARD #A084-91871-E000 OR #A084-91871-F000 PROGRAMMED 68000 VIDEO BOARD #A084-91871-AF09
| POS. | PARTNUMBER | POS. | PARTNUMBER |
| 3C F09B42605-0000 | 9J | FO9A-126 11-0000 | |
| 3B F09B-12606-0000 | 10J | FO9A-12612-0000 |
2C F09B-12607-0000 11D = F09A-12613-0000
| 2B F09B-12608-0000 | 12D | FO9A-126 14 -0000 |
| 7J — FO9A-12609-0000 | 14E | F09A-12801-0000 |
8J — F09A-12610-0000
VIDEO BOARD JUMPER WIRE CONFIGURATION
(Tone Te oe Tone Pine er ne Te Tos a
UNPROGRAMMED SOUNDS GOOD BOARD #A084-91863-8000 PROGRAMMED SOUNDS GOOD BOARD #A084-91863-AF 09
POS PART NUMBER U17 FO09A-12601-0000 U7 ~~ FO9A-12602-0000 U18 FO9A-12603-0000 U8 FO09A-12604-0000
SOUNDS GOOD BOARD JUMPER WIRE CONFIGURATION
RELEASED FOR PRODUCTION BY: ENGINEERING _ INITIAL: JUMPERS ww | owe [20 |
pate: 4-26-88 pate: 4/2 8/58 RELEASED TO EDC BY: TECHNICAL INFORMATION _ INITIAL:(;
MO5 1-O0FOS-A008
3-24 GLOSSARY OF UNIQUE TERMS AND ABBREVIATIONS
The following list of unique terms and abbreviations are used in the XENOPHOBE Parts & Operating Manual. Service Technicians and Operators should note that more than one description may apply to a particular term or abbreviation. Also, more than one term or abbreviation may apply to a particular description. Either way, the Technician or Operator need only be concerned with correctly matching the term or abbreviation with the corresponding description.
TERA/ABEREVIATION] DESCRIPTION A,AD,ADDR Address AX Axial BD, BRD Board c Capacitor, Common CER Ceramic COM Common CONN Connector CPURST CPU Reset
| cr | Diode | | |
CRBN Carbon D Data, Diode DAC Digital-Analog Convertor
| F | Fuse | / |
FB Ferrite Bead HS Heatsink J Connector, Plug JW Jumper Wire
| MTG | Mounting | i |
MTR Meter N.C. Normally Closed N.O. Normally Open PB Push Button PLY, PLYR Player PWR Power Q Transistor, Silicon Controlled Rectifier (SCR), Darlington R, RES, RM Resistor RIN Return SHLO Shield SND Sound SH Switch T Transformer W/MXR With/Mixer XSTR Transistor XTAL, Y Crystal
SECTION 4 ~ APPENDIX
The following information consists of excerpts from the WELLS GARDNER SERVICE MANUAL for K7000 Monitors.
This information is reprinted with the permission of Wells Gardner Electronics Company.
VIDEO INTERFACE AND OUTPUT The red, green, and blue video inputs come into the monitor atP1. Isolation and attenuation is provided by emitter followers Qt, Q2 and Q3. Forced blanking of the video signals is provided by the circuit of Q4, D5, D6, and D7. The forced blanking causes there to be an interruption in the video signal before it goes to the inputs of IC1. This interruption occurs between scan periods, while retrace is taking place; it is required by IC1. The forced blanking is not necessary for most video signals since they already have an interruption of video (blanking) between scan periods. Some do not; it is to accommodate such signals that the forced blanking circuit is included.
The red, green, and blue signals go into IC1 at pins 2, 4, and 6 Their levels are controlled by the gain of separate channels of the contrast amplifier. The gain is controlled by a DC voltage input to pin 11, which varies with the setting of the contrast control.
IC1 provides blanking of the video during retrace in response to blanking pulses at pin 13, derived from the horizontal and vertical sweep circuits. \C1 also requires a gating signal at pin 12 in order to provide red, green, and blue outputs at pins 21, 19, and 17. If the gating signal is not present, IC1 will not provide video output signals. The gating signal comes from IC-2, pin 12 and is derived from horizontal sync.
The brightness is varied by varying the DC level of the outputs at pins 17, 19, and 21. This is accomplished by varying the DC voltage input to pin 14.
The video outputs from IC1 are provided via R30, R31, and R32 to the neck board where they are amplified by the vidso output stages Q201, Q202, and Q203 before being applied to the cathodes of the CRT through R10, R11, and R12.
SYNC Sync is applied at P1 (positive sync) or at P2 (negative sync). Composite sync should be applied only to the horizontal sync input of the appropriate polarity. Positive sync is inverted by Q5 and Q6 then applied through D3, D4 and R51 to the sync amplifier Q7. The sync amplifier output is applied through C22, R53, and R55 to pin 14 of IC2. Pin 14 is the sync separation input.
The syn¢ Separator extracts the horizontal and vertical sync from each other-providing horizontal sync to the horizontal AFC circuit in the IC. A composite sync output is provided at pin 12. This output signal is used for gating IC1 the video interface IC and for triggering the vertical oscillator.
MONITOR THEORY OF OPERATION
HORIZONTAL OSCILLATOR AND OUTPUT The horizontal AFC circuit of |C2 receives a horizontal sync input from the sync separator and a feedback signal at pin 1, derived from the horizontal output. Slight differences in frequency and phase of the two signals will cause the AFC. to generate a correction voltage at pin 2. The horizontal oscillator inIC 2 has its free running frequency determined by the RC time constant of C19, R56, R57, R58, and VR2, the horizontal hold control. The horizontal hold control varies the horizontal frequency by varying the RC time constant. Slight correction in frequency is provided by a correction voitage at IC2, pin 3 which comes from pin 2 through R60. The oscillator output at pin 4 is amplified and shaped by the horizontal drive stage Q10. The drive signal is then coupled to the base circuit of the horizontal output transistor Q11 by the horizontal drive transformer T2.T2is used forimpedance transformation to provide the Q11 base circuit with the low impedance source that it requires. The horizontal output transistor Q11 is operated as a switch. {t is either on or off. It is turned on and off at the scan rate which is determined by the horizontal oscillator frequency which is ultimately determined by the incoming horizontal sync frequency. A yoke current with a sawtooth waveform is needed to deflect the beam linearly across the CRT. The beam begins at the center of the CRT and is deflected from center to right. This center-to-right deflection occurs when Q11 is turned on. The deflection yoke coupling capacitor C38, also known as the S-shaping capacitor, begins to discharge through the yoke; the discharge current causes the beam to be deflected to the right CRT edge. At this time, Q11 is turned off, and the current provided by C38 stops. As the current falls to zero, a voltage is induced across the yoke windings as the magnetic field collapses; an oscillation is produced by the yoke windings and C36, the retrace tuning capacitor. During the first half cycle of oscillation, the induced voltage is impressed on the collector of Q11, C36, and the primary of they flyback transformer T1. This induced voltage is stepped up by the flyback transformers secondary winding. This high voltage is then rectified and applied to the high voltage anode of the CRT. When this induced voltage occurs, the electron beam is deflected from the right edge of the CRT face to the left edge. This is called retrace. During the second half cycle of the oscillation (of C36 and the yoke windings), the voltage at the Q11 collector tries to go negative or below ground. When this happens, the damper diode (include in same package with Q11) becomes forward biased. The conduction of the damper diode allows energy stored in the horizontal system to decay linearly to zero, thus allowing the beam to return to the center of the CRT face. The focus voltage and the screen, G2, voltage are obtained from the anode voitage with a resistor divider network withip the T1 assembly. An auxiliary winding (pin 10) provides feedback.to the horizontal AFC through R71, R70, and C29. This signai is also used to furnish the horizontal blanking input to IC1 via C28, R69, and R68. The signal from the auxiliary winding at pin 5 of Tt is rectified by 014 and filtered to provide the +12VDC supply for the video interface and sync circuits. The auxiliary winding of pins 3 and 4 produces a signal which is rectified by D13 and filtered to produce the +24VDC supply for the vertical output circuit. The honzontai linearity coil 1.2 is a magnetically biased coil which shapes the yoke current for optimum linearity. The horizontal size coil L1 is a variable series inductor which is used to vary the horizontal! size of the display.
HIGH VOLTAGE HOLD-DOWN CIRCUIT The high voltage hold down circuit is part of the main PC board P447 of this monitor. The +12V DC supply is sensed via D10. Since the +12V DC supply is flyback pulse derived, the +12V DC supply will rise as the high voltage rises. If the +12V DC exceeds a threshold which is set with VR8, then D12 will conduct, thereby providing drive to IC2, pin 5— holddown input of deflection oscillator IC. The drive being applied to pin § causes the horizontal! oscillator within the IC to shut down-thus preventing the generation of high voltage. The horizontal oscillator will remain in its OFF state, even if the input to IC2, pin 5 is removed. unless and untii AC power is removed from tne monitor input. The power may then de reapplied.
VERTICAL OSCILLATOR AND OUTPUT The composite sync ouput of IC2, pin 12 is filtered through the network of R65, C25, C24 and R66 so that only vertical sync is applied to the vertical trigger input at pin 11. The vertical oscillator frequency is contrclled by the vertical hold control and its input to pin 10.
The vertical drive output at IC2. pin 7 is applied to pin 4 of IC3, the vertical output IC. Output current from IC3, pin 2 flows through the yoke to cause vertical deflection. During upward deflection, current flows out of pin 2, through the yoke, and into C50 to charge it. Downward deflection is caused by C50 discharging through the yoke in the opposite direction and back into IC3, pin 2. AC feedback is provided through the wiper of the vertical size control VR4 to C2, pin 8 in order to control the drive amplitude. DC feedback at!C2, pin 9 maintains good vertical linearity at all sizes. OC current from the +24V supply flows through R83 and through the yoke to provide downward raster shift. Some of this DC current is diverted from the yoke through the collector of Q9. The amount of this current which is diverted from the yoke can be varied by varying the base drive toQ9 by adjusting VR3, the vertical position control, thus providing manual adjustment of the vertical position of the display. The drive signal at C3, pin 2 is also used to furnish the vertical blanking input to IC1, pin 13 via R63 and C14.
AUTOMATIC DEGAUSSING ADG The ADG circuit automatically demagnetizes the CRT. This Circuit is activated only when the monitor is initially powered up after having been off for at least 20 minutes. R105 is a positive temperature coefficient device. When it is cold, it has a very low resistance. As it gets warm, its resistance increases. If the monitor is cold when AC power is applied, then R105 with a low resistance allows current to pass through it, D23, D24, and the degaussing coil. As current flows through R105, it heats up and eventually has a very high resistance, allowing very little current to flow through it. The residual current now flowing through R105 produces a voltage drop across R104 of less than 0.6 volts. This is not enough to forward bias D23 and D24, so there is no current through the degaussing coil. The process of initially having a large current through the degaussing coil and then having the current decay to zero is what produces the degaussing action. The degaussing current decays to zero before the CRT warms up, so the degaussing is completed before the picture comes on
TYPICAL OSCILLOSCOPE WAVEFORM PATTERNS
The waveforms shown below were observed on a wide band oscilloscope. The input signal was from a crosshatch generator with a horizontal syne frequency of 15.73kHz and a vertical frequency of 60 Hz. If the waveforms are observed on an oscilloscope with a limited high frequency response, the corners of the pulses will tend to be more rounded than those shown, and the amplitude of any high frequency pulse wil tend to be less. MONITOR TROUBLESHOOTING CHART
NO PICTURE SEE NOTE & NO ‘HIGH VOLTAGE Each photograph is numbered. These numbers correspond to the circled numbers on the schematic diagrams.
Photographs 12. 13, 14, 15 and 16 are of the red signal at various’ points along the red video channel corresponding points along the green and blue video chennels will look similar. The wavetorms at
EOS TN aa
| CAT FILAMENT LT | Ls) | a createn | Trica ine neck | LNO gel CHECK AC |
THAN 130 YOC | goano,P202.PIN 3 |B a Y Ws
| GnEGK FOR Gate | cnEcK | TOOKTOR CAREOF | ||
| utse atic | Feawent | GHEGKFORSHORTED|ice | | SronteD Ice OVERLOAD | |
| aves | omeut | 8 REGULAT | snonvee”| | CONDON SHORTED |
ae Ont FOR EXAMPLE CHEEK ALONG vdEO iedox wb, | Staxneterow woeo IReUT AT eTOOEO Sere QUTAUE TRANSISTORS: IF FUSE IS OPEN. CHECK
| Ow necx BOARD | USNG VARAG DECREASE AC pur] | | FUSEIS OPEN CHECK |
Y YSizcno tnewsromr meneace | | FORSHORTED HOR OU,
| 2V DIV. | 20 wSEC | Vil | ; | e | Tone | aE | ae | SHORTED 8+ REGULATOR. ICA | ||||||
| Vv | Div | a! | ‘ov | 2VIDIV | 10 wSEC CIV | OS5V01IV | 20 uSEC DIV | O26 DIV | SMSEC DIV | | CHECK FOR GATE | REFER TONO | | | rn | a i |
| pst outout wach VOLTAGE ;
| " | SNS | Does NT OPenare |
CHECK FOR OPEN CHECK WHETHER HOR OS- HORLZONIAL YORE | ectcrome eeewnone creci nernace
| cRCUT | (CHECK WAVEFORM * AND | TOR. C36 |
t IC2Pne 1236 AN0 16
REFER 10 Syne Prow.ons cna THY HOLD DOWN Gnu iS PREVENTING MON Ton OPERATION AT NOMUAL AG RUT CHECK FOR FAULTY CONDITION CAUSING HV TO BE TOO HIGH. EXAMPLE: C36 DECREASED IN VALUE
| TOvIolV | SMSEC'OIV | 2V'DIV. | 20 uSEC.OIV | Tv OIV | 20 uSECOIV | OSV OIV | 10SEC DIV | SYNC PROBLEMS |
: SEE NOTE 8 (CHECK HV HOLD DOWN GincUrT 010, 012.1C2
NO HOR SYNC
NO VERT SYNC
| [noverr syvc | | | VERTICAL: | SWEEP- PROBLEMS |
| HOW SYNCOK | ! | TTT | SEE NOTES =2- |
(CHECK SYNC
| MeL CRT | BRIGHT. THN | wo.orvery | | [ouecx] | [creck | ||||||||
| WAVY LINE AT | LITTLE VERT! | zy | TOKE | |||||||||
| 20v DIV | 20 wSEC/DIV | OSV'DIv | 20 uSEC'OIV | Sv/DIV | 20 USEC DIV | IvDIv | QO. 2MSEC DIV | Y | o_o | ae | * | - |
creck CCHEGK HOR SYNC 12 INVERTER CKT 06
| Y | GrEgKFOR OPEN VERT | re |
oer check CAL YOKE WINDINGS OF ea
ic2 (C2 VERTICAL YOKE PATH
| ‘CHECK VERTICAL OSG | y | eae | CHECK VERTICAL | |
| LATOR AND TRIGGER CKTS | (CHECK HOR | (CHECK VERTICAL | OC BLOCKING | DRIVE AND FEED: |
- PINS 10.11 12.ANO 13 AFC 1C2.PINS 2 AND 3 PosiTION cKT a9 [ME] CAPAETOR FE Back CKTS.1C2 | PINS 7.8.9.10 & 11
O.2MSEC DIV
| tw Div | O2MSEC-OIV | qv ow | 2v OV. | O2MSEC'OIY | tw olv | O2MSEC:DIY |
TROUBLESHOOTING NOTES
- Replacement parts may be ordered from the Service Department between 7:00am and 4:30pm
- The troubleshooting chart mentions spectic components to be checked. It is intended that the Central Time. entire circuit associated with these components be checked.
- All monitors are equipped with automatic degaussing coils which demagnetize the picture tube every time the monitors turned on atter being off fora minmum of 20 minutes Should any partof the chassis become magnetized it will be necessary to degauss the aftected area with a manual de gaussing coil Move the coll slowly around the CRT face area and all surrounding metaloarts Then slowly withdraw for a distance of 6 feet before turning off
- This chart is a guide to servicing rather tran a complete list of each component that could fail Therefore, troubleshooting should not be limited only :o those components mentioned in the chart
3.Itis always useful to begin checking a circuit by measunng the DC voltages and then companng the measurements to those listed in the Typical OC Voltages chart.
- Horizontal vs. Vertical:
- The cutoff controls and drive controls on the neck board and the screen control at the bottom of ‘Some models have the picture tube mounted vertically rather than honzontally That's. he picture the flyback transformer have been preset at the factory When servicing the monitor for a lack of video, do not adjust any of these controls unless it is suspected that the problem is a result of these controls having been tampered with. Otnerwise do not adjust these controls. if they are so severely out of adjustment that there is a tack of video, then there is something malfunctioning
5, The Wells-Gardner Service Department does accept telephone calls for servicing assistance. Call 1-312-252-8220, between 7:00am and 3:33pm Central Time. Ask for the Service Department. The Service Department is closed during the first two weeks of July Telephone assistanceis not available ‘during this period. Before calling, be sure to have available the mode! number of the monitor being serviced and the schematic diagram of the mcnitor being serviced. tube ts mounted in the frame such that the long dimension of the tube is up and down. Examples of this include (but are not limited to) Models 13K7851 and 19K7951. Other than the physical orientation of the picture tube, there is no electncal difference between these models and their horizontal counterparts. The same circuits, the vertical circuits, produce and control deflection along the short dimension of the tube in all models.
The same circuits, the horizontal circuits, produce and contro! detection along the long dimension of the tube in all models. Therefore, wherever “vertical” appears in this manual or on the monitor, it refers to the short dimension of the picture tube; wherever “honzontal” appears. tt refers to the
P448 ce WA 29.0mmnECK 7
- FESESSESS a ” \
Rn sex
CONTRAST va7 tox c2, 22
CUTOFF ORIVE CUTOFF ORIVE CUTOFF DRIVE
=< —om ALTERNATE CRT AND NECK BOARD 456789100
Peiso7e 191917 16 15 14 13
a ‘ z 13K7800 SERIES ee a Sines sae 19K 7600 SERIES po Tear ex ISK7900 SERIES wu Fao wore
| to | ei | aol | Tana | Sy” | fcr | REFER To OTHER seuewaric | ||
| « | TOOK | |ADJUST: | yrs | ¢20, | TiS Nir cat | De | DIAGRAMS FOR CERTAIN UNIQUE | i | |
| VERT SYNC | Rae. | lecoa semen) | lex | sv | Ho,25v | A | MODELS | ‘ |
| ‘eu | cy | a6! | Rco | & |
ei
| / exo 1 | tet... | PE | eo | : |
mae | gory ‘ asase eA 1 Au RatSTORS ARE I Ons, 50M v2 O TReR fz sas 6 7 Gl MCE VALUES LESS THAN | ARE IK an3904 ast o7 Le a oa © big is 154 132 10 9) CERTAIN WAVEFORM REAOINGS
So nad FO, Bi cautiom sertre corviea commonen
| cso | IK | zzox ] TP | + |
as Wea-nar eactarion evateo couranent 17 acse 4m 47K REPLACE ONLY WITH SAME TYPE PARTS AS SHOWN IN PARTS LIST. | 3 CIRCLED NUMBERS INDICATE LOCATIONS OF
Roe Roe 22KIw 22K IW SVD ‘S622
| p20 | Yow | soov | sen” | rib |
vA 220,15w 6.8K porti5 Sw 58 fi yt: Tridel o22_j.oozz
| 7 | ee | a |
err 33K GP: paar eae,
ut ue SIZE | LINEARITY
VERTICAL POSITION ba es ee edt Lege f22" 2000 ieov WARNINGS OEGAUSSING 1. Power Up WarningcoIL v An isolation transformer must be used between the AC supply and the AC plug of the monitor before servicing, (esting, a 2 ee ee u 0+ operating thé monitor since the chassis and the heat sink are directly Connected to ane side of the AC line which could et resent a shock hazard #R302 IS PRESENT ONLY ON Betore servicing is performed, read all the precautions labelled on (he CRT and chassis, 197600 an {9K7900 SE RIES MONITORS, 333: 50-6OHz 2.[_ X-RAY RADIATION WARNING NOTICE
- High Voltage - Thus monitor cantains HIGH VOLTAGES denved trom power suppives capable of delivering LETHAL quantities of energy De not attempt to service until ail precautions necessary for working On HIGH VOLTAGE equipment have been observed
- CRT Handling Care must be taken not to bump or scratch the prcture tube as this may cause the picture tube f0 snplode resulting 19 personal snyury Shatter proof gogyles must be worn when handing the CRT High vottage must de completely drscharged before handing Do not handle the CRT by the reck
5.[_ PRODUCT SAFETY NOTICE
VERTICAL SIZE
GENERAL REPLACEMENT PARTS LIST For all K7000 models except where noted. This monitor contains circuits and components included specifically for safety purposes. For continued protection no changes should be made to the original design, and components shown in shaded areas of schematic, or A on parts list should be replaced with exact factory replacement parts. The use of substitute parts may create a shock, fire, radiationorother hazard. Service should be performed by qualified personnel only.
P447 MAIN BOARD
| Ret. | Part No. | Description | Ret. No, | Part No. | Description |
RESISTORS RESISTORS (Cont)
| a | 340X2562-034 | 5.6K Ohm 5% 0.25W | ase | 340X2103-934 | 10K Om 5% 0.25W |
| R2 | 340X2562-934 | 5.6K Ohm 5% 0.25W | Reo | 3402563934 | 56K Ohm 54% 0.25W |
| R3 | 340%2562-934 | 5.6K Ohm 59% 0.25W | Ret | 340X2332-034 | 3.3K Ohm 5% 0.25W |
| Ra | 340X2472-934 | 4.7K One 5% 0.25W | R62 | 340X2122-034 | 1.2K Ohim 5% 6.25W |
| RS | 340X2472-934 | 4.7K Ohm S% 0.25W | R63 | 340X2563-934 | 56K Ohm 5% 0.25W |
| R6 | 340X2472-934 | 4.7K Ohm 5% 0.25W | R64 | 340x2184-934 | 180K Ohm 5% 0.25W |
| R7 | 340X2333-934 | 33K Ohm 5% 0.25 | ROS | 340X2123-934 | 12K Ohm 5% 0.25W |
| RB | 340X2333-934 | 33k Ohm 5% 0.25 | R66 | 340X2224-934 | 220K Ohm 5% 0.25W |
| RQ | 340X2333-934 | 33K Ohm 5% 0.25 | RET | 3402623934 | 62K Ohm 54% 0.25W |
| R10 | 340X2151-934 | 150 Ohm 5% 0.25w | R68 | 340X2223-934 | 22K Ohm 5% 0.25W |
| RIT | 340X2151-934 | 150 Ohm 5% 0.25W | R69 | 340X3683-231 | 68K 5% 0.5W CAR |
| RI2 | 340X2151-934 | 150 Ohm 5% 0.25W | R70 | 340X2682-934 | 6.8K Ohm 5% 0.25 |
| R13 | '340X2102-934 | 1.0K Ohm 5% 0.25W | R71 | 340X3473-234 | 47K 5% 0.5W |
| Ria | 340X2102-034 | 1.0K Ohm 5% 0.25W | R72 | 340X2101-934 | 100 Ohm 5% 0.25W |
| RIS | 340X2102-934 | 1.0K Ohm 5% 0.25W | R73 | 340X2103-934 | 10K Ohm 5% 0.25W |
| R16 | 340X2822-934 | 8.2K Ohm 5% 0.25W | R74 | 940X2220-934 | 22 Ohm 5% 0.25W |
| R17 | 340X2B22-934 | 8.2K Ohm 5% 0.25W | R75 | 340X2222-034 | 2.2K Ohm 5% 0.25W |
| RIB | 340X2152-934 | 1.5K Onn 5% 0.25W | R76 | 340X2473-934 | 47K Ohm 5% 0.25W |
| R19 | 340X2103-234 | 10K Ohm 5% 0.25W. | R77 | 340X2333-034 | 33K Ohm 5% 0.25 |
| R20 | 340X2102-934 | 1.0K Ohm 5% 0.25W | R78 | 340X2102-934 | ‘1.0K Ohm 5% 0.25W |
| R21 | 340X2563-934 | 56K Ohm 5% 0.25W | R80 | 340X3056-934 | 5.6 5% 0.5W |
| R22 | 340x2562-934 | 5.6K Ohm 5% 0.25W | RBI | ‘340X2150-934 | 15 Ohm 5% 0.25W |
| R23 | 340X2102-934 | 1.0K Ohm 5% 0.25W | R82 | 340X3821-834 | 820 Ohm 5% 0.5W |
| R24 | 340X2224-934 | 220K Ohm 5% 0 25W | Ras | 340X3681-074 | 680 Om 5% 0.5W |
| R25 | 340X2273-934 | 27K Ohm 596 0.25W | Rea | 340X2682-934 | 6.8K Ohm 5% 0.25 |
| R26 | 840X2822-834 | 8.2K Ohm 5% 0.25W | RSS | 240X2332-034 | 3.3K Ohm 5% 0.25 |
| R27 | 340X2223-034 | 22K Ohm 5% 0.25W | R86 | 340X2224-934 | 220K Ohm 5% 0.25W |
| R28 | 340X2332-934 | 3.3K Ohm 5% 0.25W | R87 | 340X3334-644 | 330K 10% 0.5W |
| R29 | 340X2103-934 | 10K Ohm 5% 0.25W | R88 | 340X4182-633 | 1.8K 5% 1W |
| R30 | 340X2101-934 | 100 Ohm 5% 0.25W | R89 | 043x0476-002 | 3.9K 5% 5W MO |
| R31 | 340X2101-934 | 100 Ohim 5% 0.25W | 90 | 043x0486-002 | 1.2 5% 2W MF |
| R32 | 340X2101-934 | 100 Ohm 5% 0.25W | Rot | 043x0486-002 | 1.2 5% 2W MF |
| R33 | 340X2102-934 | 1.0K Ohm 5% 0.25W | oz | 043X0486 002 | 1.2.5 2W ME |
| R34 | 340X2102-934 | 10K Ohm 54% 0.25W | R93 | 420X5102-324 | 1.0K 5% 2W |
| R35 | ‘340X2102-934 | 1.0K Ohm 5% 0.25. | R94 | 340X2473-934 | 47K Ohm 5% 0.25W |
| R36 | 340X2122-034 | 1.2K Ohm 5% 0.25W | ROS | 340X2473-934 | 47K Ohm 5% 0.25W |
| R37 | ‘340X2822-934 | 8.2K Ohm 5% 0.25W | ROG | 420X6182-325 | 1.8K Ohm 5% 3W, WW |
| R38 | 340X2122-934 | 1.2K Ohm 546 0.25W | R97 | 420X6271-325 | 270 5% 3W |
| 39 | 340X2122-934 | 1.2K Olin 5% 0.25W | R98 | 340X4222-633 | 2.2K Ohm 5% 1W |
| Rao | 340X2102-894 | 1.0K Ohm 5% 0.25W | Reo | 340X4222-633 | 2.2K Ohm 5% 1W |
| Rat | 340X2102-934 | 1.0K Ohm 5% 0.25W | R100 | 340X427 1-633 | 270 5% 1W |
| RAZ | 340X2473-934 | 47K Ohm 5% 0.25W | R101 | 420X6682-325 | 6.8K S% SW |
| Ras | 340X2222-034 | 2.2K Ohm 5% 0.25W | R192 | 3404470633 | 47 500 1W |
| Rag | 340X2104-934 | 100K Ofim 5% 0.25W | AxR103 | 043x0483-001 | 2.7 Ohm 5% 7W |
| Ras | 340X2104-934 | 100K Ohm 5% 0.25W | R104 | 043X0484-001 | 15 Ohm 5% SW |
| RAG | 340X2101-934 | 100 Ohm 5% 0.25W | R105 | 043X0485-001 | Themnister |
| Ra7 | '340X2101-934 | 100 Ohm 5% 0.25W | R106 | 340X2273-934 | 27K Ohm 5% 0.25W |
| R48 | 340X2102-934 | 1.0K Orn 5% 0.25W | R107 | 340X2102-934 | 1.0K Ohm 5% 0.25W |
| Rag | 340X2102-934 | 1.0K Ohm 5% 0.25W | R301 | 043x0481-003 | 220 Ohm 15w WW |
| R50 | 340X2103-934 | 10K Ohm 5% 0.25W | vRt | (040x0653-002 | CTRL 500 |
| R51 | 340X2103-934 | 10K Ohm 5% 0.25W | vR2 | 040x0653-005 | CTRL 10K |
| R52 | 340X2102-934 | 1.0K Ohm. 5% 0.25W | vR3 | 040X0653-005 | CTRL 10k |
| RS3 | 340X2151-934 | 150 Ohm 5% 0.25W | vRa | 040X0653-001 | CTRL 200 |
| R54 | 340X2224-934 | 220K Ohm 5% 0.25W | VRS, | 040X0653-006 | CTRL 200K |
| RSS | 340X2101-934 | 100 Ohm 5% 0.25W | VRE | 040X0653-003 | CTAL 2K |
| 56 | 340X2472-934 | 4.7K Ohm 5% 0.25W | vR7 | 040X0653-005 | CTRL 10K |
| Rot | 340X2182-934 | 1.8K Ohm 5% 0.25W | VRB | 040x0639-006 | Trim Pot 2k Ohm 0.3W |
| R58 | 340X2123-934 | 12K Ohm 5% 0.25W | vR9 | 040x0655-001 | Trim Pot 200 0nm |
FINAL ASSEMBLY PARTS et No. PartNo, Description 13K7800 SERIES (13")
| At | 88X0236-506 | CRT Orion A38JLLOOX |
- 942860-001 Deflection Yoke 2A0690-001 Purity & Convergence Ring Assembly 982856-001 Degaussing Coil Assembly '8X0378-001 Rubber Wedge 19K7600 and 19K7900 SERIES (19”)
| Ar | (88X0237-506 | CRT Philips MVA4BABKOSX |
- '942862-001 Deflection Yore 200890-001 Punty & Convergence Ring Assembly 942857-001 Degaussing Coll Assembly 208X2400-901 Rubber Wedge P447 MAIN BOARD (CONT.)
| Ret. Ho. | Pact to. | Desctiotion | Ret. No. | Part No. | Descrlotion |
CAPACITORS SEMICONDUCTORS
| ce | oeoxtogs ert | Bie 2 le NeO | 03 | 066x0070-001 | Diode 1NS145 | |
| cs | ggoxnose st | Disc eee | os | 066X0070-00% | Diode 1N9148 | |
| ca | (045X0577-501 | Elect 10M NP 25V | Be | sepere | Bede tae | |
| cs | (045x0577-501 | Elect 10MF NP 25V | Et | Le rereliped | Diode 1ND148 | |
| és | (045x0577-501 | Elect 10MF NP 25V | i | (08640070001 | Diode 1NB148 | |
| c7 | 047x0786-502 | MYR 022 10% SOV | Ed | Pence | Eee bby | |
| e | Ppt | phi tated cd | 09 | 066x0070-001 | Diode 1N9148 | |
| ce | botelie ce | eee | o10 | 066x0079-001 | Diode 1NS148 | |
| ey | beri | eoy | Esepsged | on | (066X0040-028 | Zener Diode 5.1V 5% 0.5W |
| qu | ‘oasieas 60-594 | See | Diz | 066X0040-005 | Zener Diode 10V 5% 0.5W | |
| a | Peer iny | oe | 013 | 066x0090-001 | D1 Fast SW RU-2 | |
| 4 | peat eres | Be a ae | Dia | 066X0090.001 | D1 Fast SWAU-2 | |
| ce | Piet ea | tive oes en boy | #015 | 066x0090-001 | 01 Fast SW RU-2 | |
| cis | Seatac eit | MYR 022 10% EV | 016 | (066x0090-001 | D1 Fast SW RU-2 | |
| cis | belie | MYA | Oe ey | o17 | 066x0090-001 | 01 Fast SW RU-2 |
| 7 | (047x0786-501 | ‘O1OUF 10% SOV P-Estr | rot | seexcom0 a1 | Dies sw AUS | |
| 18 | 045x0560-514 | LYT £.0UF Sov | a | b8 | Seecoee a | Diode samo Gre) |
| 19 | 046X0550-502 | P0056 2% AWS SOV | & | b33 | Sbexcce! 001 | Diode $1 1A 600V |
| ce | ore ypeen sie | ty love sev | A | p21 | (066X0091.001 | Diode Si 1A 600V |
| o2 | Persson aia | rie | A | 022 | 066x0091-001 | Diode Si 1A 600V |
| ae | orexpeon et? | oa | 023 | 066x0091-001 | Diode St 1A 600V | |
| a | OesKoseo ST | nes oe | oz | 066x0091-001 | Diode SI 1A 600V | |
| C24 | (047X0786-503 | MYR 068 10% SOV | pet | Seekoes 201 | a | |
| 625 | 047K0786-512 | PEster 015 10% SOV | 2 | 956x0068-001 | BBM aniaond | |
| C26 | OUxOrES S1Y | Pee ateaed | a2 | 086X0113-501 | TRSTR NPN 2N3904 | |
| ou | oeoxo0s) 857 | Oe 220 ON eee | 3 | 086x0113-501 | TASTR NPN 2N3004 | |
| C28 | Opoxooss 048 | St aoe Ne | a4 | 086x0113-501 | TRSTR NPN 2N3904 | |
| C29 | oq7xn7e6 50! | O1OUF 10% SOV P-Estr | as | 086X0113-501 | TRSTR NPN 2N3904 | |
| C30 | erred | Oise 001 20% ZSF S00V | a6 | 86X01 13-501 | TASTR NPN 2N3904 | |
| c31 | 047x0786-501 | ‘O1OUF 10% SOV P-Estr | os | Pode | TST NEN aE | |
| C32 | 960100099280 | Biss 100 10% 25° S00V | 08 | 086X0113-501 | TRSIR NPN 2N3904 | |
| 33 | (080x0099-722 | Disc .0033 10% Y5P S00V | 8 | See | UST NPN ON | |
| oe | ceoxnoge 221 | ie OO | ato | 086X0185-501 | TRSTR NPN CC | |
| 35 | (047x0786-501 | O10UF 10% SOV P-Este | ae | Soares | ee. | |
| Aeeis | oaexns9 102 | eae ow | C1 | 086x0186-001 | IC Video UPC1397 NEC | |
| 4 | Popecreenred | pea | (c2 | (086x0187.001 | IC Honz Vert LA7823 | |
| # E38 | casero | SOUF Be 200V PP | 163 | (086X0189-001 | IC Vert Output UPC 1378 | |
| Paty | oan seo O89 | Be Oa | Anica | ¢6x0188-001 | Regulator IC STRI23 | |
| cat | 080X0099-505 | Disc 001 20% Z5F S00V | ‘at | |||
| Caz | (045x0560-006 | LYT 1000UF 16V, | ||||
| cas | (080x0099-505 | Disc .001 20% Z5F S00V | ||||
| C44 | 046x0546-009 | 1 10% 100V P-Prop | TRANSFORMERS AND COILS | |||
| as | 045x0560-020 | LYT 470UF 16V | 2954-001 | Coil Wicth-TODAI | ||
| C46 | 045X0560-020 | AT 470UF 16V | welt | 008A235: | Seabee | |
| C47 | 080X0099-580 | Disc 100 10% Z5F SOV | anne | 00942855001 | ie ie an | |
| C48 | 045X0S60-532 | Elect 100MF 35V | ars | 053X0528-001 | frase | lypack |
| vag | 047X0786-501 | CIOUF 10% SOV P-£st: | 2 | 052X0131-001 | ranst Hon | Driver |
| 250 | 945X0580023 | LYT iCO0uF 25v | ||||
| 51 | (045x0525-512 | Tan.58 10% 35V | ||||
| 52 | 047x0786-501 | O10UF 108 SOV P-Estr | ||||
| 53 | 947x0786514 | O33UF 5% SOV P-Estr | ||||
| 54 | 047x0786-515 | MYR 022 5% SOV | MISCELLANEOUS | |||
| css | 045x0578-001 | Elect 560 200V | Ar | 016x0176-001 | Fuse 1.5A SB | |
| 36 | 045x0569-008 | LYT 22UF 160V | 016x0182-001 | Fuse Clip | ||
| cs7 | (045x0569-011 | Elect 47 160V | Pr | (00640428-001 | Plug Header | |
| 59 | (080x0099-724 | Disc .0015 10% YSP S00V | P2 | 006A0428-001 | Plug Header | |
| C60 | 080X0099-723 | Disc 0022 10% Y5P SOOV | P3 | 006A0427-001 | Plug 2 Pin | |
| C61 | 1080x0099-723 | Disc 0022 10% YSP 500V | Pa | (006A0406-001 | Plug 4 Pin OSHIMA | |
| A | ce2 | 046X0552-001 | 1 20% 125VAC | °6 | 006A0429-005 | Plug Header |
| 63 | 047x0786-501 | O1OUF 10% SOV P-Este | $202 | 013x1243.001 | Cable Assy 4 Wire 350mm |
P456 NECK BOARD (used with CRT’s with a 22.5mm neck diameter) RESISTORS CAPACITORS
| R201 | 340X2272-934 | Res 27K Ohm Si 0.25W | 201 | 080x0090-006 | Cap 470PF 10% Z5F CER | |
| R202 | 340x2151-934 | Res 150 Ohm 5% 0 25W | 202 | 080x0099.006 | Cap 470PF 10% Z5F CER | |
| R203 | 340x2272-934 | Res 27K Ohm Si 0.25W | 6203 | (080X0099.006 | Cap 470°F 10% Z5F CER | |
| R204 | '340x2151-934 | Res 150 Ohh 54% 0 25W | 204 | 080X0099-221 | CE Disc 01 10% YSP 500V | |
| R205 | 340x2272-94 | Res 2 7K Ohm 5% 0 25W | 205 | 030x0099-225, | Disc 0015 1 SKY | |
| R206 | 340X2151 934 | Res 150 Ov 3 | 0 256 | |||
| R207 | 340x5682-632 | Res 6 BK 2W Mi | ||||
| 208 | 340X5682-633 | Res | 68K 2W MO | SEMICONDUCTORS | ||
| 209 | 340x5682-635 | Res 68K 2W MO | Asin | abs0aLBILA | ||
| fais | Rie eon | pieces | ace | 0203 | 086X0184.001 | TASTR 25C 2068. 8/L 88K |
| 8212 | 340X3272-244 | Res 27K Ohm 10% 0 SW | ||||
| R213 | 340x5689-333 | Res 68 Ohm 5% 2W | ||||
| vR201 | (040x0653-003 | CTRL 2k | ||||
| R202 | 040x0653001 | ETAL 200 | MISCELLANEOUS | |||
| R203 | (040x0653-003 | TAL 2k | P202 | 00680429-005 | Plug Header | |
| R204 | {940X0653.001 | ErAL 200 | SK1201 | 003A0636001 | Pix Socket | |
| vR205 | 040x0653.003 | CTR 2K | I6 | 013x1243-001 | Cable Assy 4 Wire 350mm | |
| A206 | (040x0653001 | ETAL 200 | 030x0797 001 | Plug V Pin |
P448 NECK BOARD (Used with CRT’s with a 29mm neck diameter) Same as P456 NECK BOARD except: SKT201 (003A0651-001 SOC CRT