CATHODE RAY TOMES

Guardians of the Hood TM-377 1st Printing Kit

Guardians of the 'Hood (Atari Games, 1992) · Kit Manual · 58 pages · 75 sections · original scan

Page 1

WET! the bes i Figure £24 bhod walt Care bhocks 9 Mart et

-—_ 2“7*és'

STALLATIO! \

oe—i4ae
:N\.—:-‘cos:/ the
.™>:‘od; '

4 he he ie \ od , 3 e ae hn »

fyY'\
Page 2

orm

This entire manual was printed on recycled paper cs)

Page 3

Universal Kit

Installation Instructions

Conversion kit for upright games

Page 4

Gvarpiass OF THE “Hoop Kre INTRODUCTION #

Copyright © 1992 by Atari Games Corporation. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in . nor may it be the form of a phonographic recordin; stored in a retrieval system, transmitted, or otherwise copied for public or private us without permission from the publisher The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the dis play manual are protected by the U Copyright Act of 1976. This Act provides for substantial penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory action in damages of up to $50,000 per infringing tran: certain cases, Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of

corporations Atari Games Corporation will aggressively enforce its | We will use all legal copyrights against infringers distribumeans to immediately halt any manufactur tion, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by Atari Games Corporation 675 Syeamore Drive P.O, Box 361110 Milpitas, California 95036 SAL 06/92 Produced by the Atari Games Technical Publications

Department Writing and Editing: Andrea Dencker and Pat Cook Ilustration and Design: Mary Ohanessian Sumner Printed in the U

ii

WARNING Use of non-Atari parts or modifications of any Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players:

You may void the game warranty (printed on the in cover of this manual) if you do any of the side bac following:

  • Substitute non-Atari parts in the game. © Modify or alter any circuits in the game by using kits or parts of supplied by Atari Games Corporation

This equipment generates, usc; frequency energy, and if not installed «and used in aeand can radiate radio

cordance with the instruction manual, may cause inter ference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment int residential area or modification to this equipment is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference, H you sus: pect interference from an Atari game at your location, check the following: © All ground wires in the game are properly connected as shown in the game wiring diagram © The power cord is properly plugged into a grounded three-wire outlet © On games provided with an Electromagnetic Interlerence (EMD ground plane, be sure that the game Is (PCBs) are properly installed on printed-cireuit bos the EMI ground plane and that the end board is securely installed with all screws in place and tightened If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area

Page 5

GUARDIANS OF THE Hoop Kre_ 4% INtRODUCTION

SAFETY

SUMMARY

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found in this manual whenever they apply.

WARNING

Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded threewire outlet. If you have only a two-wire outlet, we reclicensed electrician to install a not ommend you hire three-wire grounded outlet. If the control panel is properly grounded, players may receive an electrical shock! After servicing any part on the control panel, check that the grounding wire is firmly secured to the inside of the control panel. After you have checked this, lock up the game.

AC Power Connection. Before you plug in the game, be sure that the game's power supply can accept the AC line voltage in your location. The line voltage requirements are listed in the first chapter of this manual

Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power before removing or repairing any part of the game. If you remove or repair the video display, be very careful to avoid electrical shock. High voltages continue to pl: ist even after power is disconnected in the dis cuitry and the cathode-ray tube (CRT). Do not touch the internal parts of the display with your hands or with metal objects! Always discharge the high voltage from the CRT before servicing it. Do this after you disconnect it from the power source. First, attach one end of a large, well-insulated, 18-gauge jumper wire to ground. Then momentarily touch the free end of the grounded jumper wire to the CRT anode by sliding the wire under the anode cap. Wait two minutes and do this again. Use Only Atari Parts. Yo maintain the safety of your Atari game, use only Atari parts when you repair it Using non-Atari parts or modifying the game circuitry may be dangerous, and could injure you and your players. Handle the CRT With Care. If you drop the CRT and it breaks, it may implode! Shattered glass from the implosion can fly six feet or more. Use the Proper Fuses. To avoid electrical shock, use which are specified in the parts list replacement fuse: for this game. Replacement fuses must match those re: placed in fuse type, voltage rating, and current ratir In addition, the fuse cover must be in place during game operation.

CAUTION

Properly Attach All Connectors. Make sure that the connectors on each printed circuit board (PCB) are properly plugged in. The connectors are keyed to fit only one way. If they do not slip on easily, do not force them. If you reverse a connector, it may damage your game and void your warranty. Ensure the Proper AC Line Frequency. Video games manufactured for operation on 60 Hz line power (used in the United States) must not be operated in countries with 50 Hz line power (used in Europe). If a 60 Hz the fluorescent machine operates on 50 Hz line pow line ballast transformer will overheat and cause a pohazard, Check the product identification label on your machine for the line frequency required

ABOUT NOTES, CAUTIONS, AND

WARNINGS

In Atari publications, notes, cautions and warnings tential fire

have the following meaning:

NOTE — A highlighted piece of information
CAUTION — Equipment and/or parts can be damaged or destroyed if instructions are not followed, You will void the warranty on Atari printed-circuit boards, parts thereon, and video displays if equipment or parts are damaged or destroyed due to failure of following instructions
WARNING — Players and/or technicians can be killed or injured if instructions are not followed.

iii

Page 6

INTRODUCTION & GUARDIANS OF THE ‘Hoop Kir

CONTENTS

1 Installation

How to Use This Manual ... Cabinet Fauipment Requirements .. Tools Required... Inspecting the Kit. . Preparing the Cabinet for the Kit Installation . Assembling the Two-Player Control Panel. Connecting the JAMMA Harness... Installing the Guardians of the Hood Board Set .. 1-10 Installing the Bezel, Decals, Labels, and Attraction Assembly... 1-10 Assembling the Three-! “Player C ontrol ‘Panel 1-10 Connecting the Optional Three-Pla’ Harnes: 1-12 Setting the Coin and Game Options... Maximizing Earnings .......... Game Play... 2 Self-Test Introduction... cee . Entering and Exiting the Self-Test..... RAM and ROM Test Sel Menu... Switch T Volume Adjust Test Sound Test Coin Options. Game Option: Game Statist Alphanumeri Motion Object Playfield Test....... Color Test.. Convergence 3 Troubleshooting and Maintenance

Introduction . Video Display Troubleshooting. Removing and Replacir ing rthe Joy stick r control. ROMs and RAMs... 4 Parts Illustrations

See the List of Illustrations that follows

5 Schematic Diagrams

See the List of Illustrations that follows:

Statistics Sheet yne Problems .

Page 7

ILLus

Figure 1-1

Figure 1-2

Figure 1-3

Figure 1-4

Figure 1-5 Figure 1-6

Figure 1-7

Figure 1-8

Figure 2-1 Figure 2-2 Figure 2 Figure Figure Figure Figure Figure Figure Figure Figure 2-11 Figure 2-12 STRATIONS

Installed Kit Parts (Two-Player Game) cesses 1-3 Installed Kit Parts (Three-Player Game). 1-4 Locations of Control Panel Holes. to Be Drilled (fwo-Player Atari cabinet). 1-7 Locations of Control Panel Holes to Be Drilled (Two-Player Dynamo Cabinet)... Co Connections for Optional Three-Player Harness . Two-Player Hole-Cutting Template for Guardians of the ‘Hood Kit Control Panel (Atari Cabinets) Two-Player Hole-Cutting Templi ute for Guardians of the 'Hood Kit Control Panel (Dynamo Cabinets) ement of ect F

Select Test Menu Sc Switch Test Screen. Volume Adjust Screen. Sound Test $ Coin Options Sc Game Options Screen . Statistics S Alphanumeric Test Ser Motion Object Test Screen .. Playfield Test Screen . Color Test Screen : Convergence Test Screen . en

Nw Figure 4-1

Figure 4-2

Figure 4-3

Figure 4-4

Figure 5-1

Figure 5-2

Table 1-1 Table 1-2

Table 1-3 Table 1-4

Table 2-1 Table 2-2 Table 2-3 Table Table 2-5

Table 3-1 ble 3-2

Table 3-3 Table 3-4 GUARDIANS OF tHE “Hoop Kin INTRODUCTION

Parts of Guardians of the ‘Hood Universal Kit (Two-Player Shown) ..... 4-2 8-Position, Gold-Contact Joystick Assembly ....... Guardians of the ‘Hood Game PCB. Assembly (FSG42GRN) ccc: dt JSA TIT Audio PCB Assembly 1

Guardians of the ‘Hood Game PCB Assembly Schematic Diagram 53 JSA Audio IIT PCB Assembly Schematic Diagram cscs sec 57

TABLE

Equipment Requirements ........0.... 1-2 Contents of Guardians of the “Hood Kit JAMMA Pin and Wire Connections 1-6 Third-Player Pin and Wire CONNECHIONS ......crsceeiinsiiaaeince LF

Summary of All Self-Test Screens. Bad RAM Location by ror Addres: Bad ROM Location by Error Address... Coin Option Settings oe... Game Option Settings occ 2-5

Peoublestoatits Tableaccccccsecsseeenseeens 32 Voltage Inputs and Test Points on the PCBs........ seccveseeee What ROM Problems Look Like... 3-3 Atari Games Video Connector Pin Assignment......scsseecesee vessseee 33

Page 8

INTRODUCTION GUARDIANS OF THE “Hoop Kit

Page 9

CHAPTER 7

Installation

HE GUARDIANS of

the “Hood” conversion

kit is a two-player game (expandable to a threeplayer game) for a standard upright cabinet. a This manual provides information for installing, testing, and troubleshooting the Guardians of the ‘Hood” conversion kit.

Chapter 1 describes how to install the Guardians of the

‘Hood kit in your cabinet. This:

chapter also describes game play. m Chapter 2 contains self-test procedures and additional diagnostic tests. The self-test is important in the How To Use THis MANUAL

NOTE The three-player option is intended primarily for a Pit- Fighter cabinet. However, you can install the three-player option if you have a game cabinet with a wide enough control pane! to accommodate the additional joystick Guardians of the "Hood game.

You can troubleshoot the PC

boards, main circuits, and

controls using the screens in the self-test. You should regu-

larly test the boards and controls with the self-test to keep

your game in peak condition and at top earnings. a Chapter 3 contains troubleshooting and maintenance procedures for the controls. m Chapter 4

contains the kit parts list and

parts illustrations. # Chapter 5 contains the schematics for the Guardians of the ‘Hood

printed-circuit boards.

Page 10

CHAPTER 1 — INSTALLATION & GUARDIANS OF THE “Hoop Kit

WARNING To avoid electrical shock, unplug the cabinet while installing the kit. After installation, plug the game only into a grounded 3-wire outlet.

Cabinet Equipment Requirements Table 1-1 lists the equipment required in the cabinet into which you are installing the Guardians of the “Hood kit.

CAUTION Do not unplug or plug in the Guardians of the ‘Hood game printed-circuit board (PCB) edge connector while the power is on. You could seriously damage the PCB.

Tools Required

  • Drill with a 1/2-inch, 3/8-inch, 7/32-inch,

and 3/16-ineh drill bits

© Phillips screwdriver © Flat-blade screwdriver

  • Socket wrench set and ratchet

men

Color RGB monitor Separate positive horizontal and vertical sync or negative composite sync Horizontal mounting Horizontal frequency: 15.750 KHz Vertical frequency: 60 Hz Video input: 1V to 3V peak-to-peak positive polarity Video Display

Control Panel Metal only

8Q,10W

+5 VDC or +12 VDC Speaker

Coin Counter

Power Cord Three-conductor with ground Power 45 VDC + 0.25V @ 3.0 amps +12 VDC @ 1.0 amp Power Supply

-5 VDC @ 1.0 amp (optional)

Table 1-1 Equipment Requirements ¢ 5/32" hex wrench

© Pencil

© Compass or circle template © Wire cutters and strippers

© Straight edge

¢ Squeegee «© X-ACTO™ knife © Insulated wire connectors (if you are installing 3 new JAMMA harness)

© Carbon paper

© Saber saw

  • Band saw

rt No. Description

72-6624S #6 x 1 1/2"-Long, Type AB, Pan-Head, Cross-Recessed Screws (4) 75-5112B #10-24 x 3/4”-Long Black Carriage Bolts (8) 038158-01 Product |.D. Label 039450-01 FCC Compliance Label 047205-01 Attraction Shield 050227-01 Control Panel Cover 050149-01 Side Panel Decals (2) 050150-01 Attraction Panel Film 050151-01 Control Panel Decal 050152-01 Monitor Bezel with Graphics

050154-01 Pushbutton Decal (3) 141026-001 5041.D. Ferrite Split Beads (2) 141026-003 40"1.D. Ferrite Split Beads (6) 160044-001 Snap-Action Switch (12) 171099-001 8-Position Black NO/NC Joystick Assembly with Gold-Plated Switch Contacts (2) 175004-706 154° x .375" x 125" Thk Fiber Washers (4) 175014-1040 177026-0040 #10 Flat Washers (8) #10-24 Zinc Nut/Washer Assemblies (8) 178020-812 Spacer, Rnd, #6, |.D.=.140, 0.D.=.25, L=.812, Nylon (4) 178032-002 #10 Wire & Cable Ties (5)

178237-001 Red Pushbutton Assembly (2) 178237-002 Yellow Pushbutton Assembly (5) 178237-005 Blue Pushbutton Assembly (5) TM-377 Guardians of the 'Hood Universal Kit Installation Instructions (with Control Panel Templates)

A049811-01 Three-Player Harness Assembly A050194-01 Switch Jumper Harness Assembly (2) A050756-03 Guardians of the 'Hood PC Board Set Packaging materials are not listed. Al parts are a quantity of 1, except as noted in parentheses.

Table 1-2 Contents of Guardians of the *Hood Kit

Page 11

GUARDIANS OF THE ‘Hoop Kir & Carrer 1 — INstal

Attraction Shield Attraction Film |

Bezel W/, Graphics | 2° Payropyene Tap! |Site Panel Decal (2Praces

oo 0 Board Set Assy.

0d consisting of

fh ote Guarcians of The Hood Game PCB Assy (FSG426AN)

ISA Ill PCB Assy.

Nylon Stand-off 2 places) #10 Black Carriage Bolt eo 16-32 Nylon Hox-N (6 places)| places (2 places)

1/4" Round Stand-off

6-32 x 318" Pan-Hd. Screw (2 places)

#6 Flat Washer (2 places}

46 Split Lock Washer (2 places}

Blue Button Assy. #6 Nylon Spacer (5 places) | (places)

trol Panel \ Cont Panes | Fiber Washer | (4 places) ro! | Control Panel 46x 1112 Pan-Hd. Screw Pushbutton Decal (places) (2 places)

Snap-Action Switch (10 places)

Yellow Button Assy. (5 places)

Figure 1-1 Installed Kit Parts (Two-Player Game)

Page 12

Cuaprer 1 ALLATION GUARDIANS OF THE “Hoop Kit

items Not Shown

A049811-01 3rd Player Harness Assy.

““

050154-01 Pushbutton Decal

178237-001 Red Button Assy. | (2 places)| 160044-001 Snap-Action Switch (2 places}

Figure 1-2 Installed Kit Parts (Three-Player Game)

Page 13

GUARDIANS OF THE ‘Hoop Krr CHAPTER 1 — INSTALLATION

Inspecting the Kit

Check to see that you have all the parts listed in the kit parts list in Table 1-2. If any part is missing or damaged, contact your distributor with the Guardians of the ‘Hood kit serial number, part number, and description of the missing or damaged parts, and date received.

Preparing the Cabinet for the

Kit Installation

WARNING To avoid electrical shock, unplug the cabinet while installing the kit. After installation, plug the game only into a grounded 3-wire outlet.

Figure 1-1 shows almost all kit parts installed in a typicabinet. Use this illustration as a guide while you install the parts.

  • Turn off power to the game, and unplug the power cord,
  • Remove the following from the cabinet:
  • Existing PCBs if iti chinery Manufacturers As compatible. Table 1-3 a ume cabinet with a JAMMA harness installed in it.
  • Game harnes: not Japan Amusement Maociation (JAMMA)— sumes you have an available
  • Control panel decals, labels, and controls
  • Side deca net sides are damaged, repair them before putaphics, and adhesive. If the cabi-

ting on the new decals.

  • Video display (monitor) shield, display bezel, attraction shield, and marquee.
  • Wipe down and vacuum the cabinet. Paint the cabinet, if required.

Assembling the Two-Player

Control Panel

Parts Needed from This Kit

To assemble the control panel, you need the two-player control panel hole-cutting template printed in Figure 1-7 or 1-8, Cut out the appropriate template sheet from this manual. You will also need the following parts from the kit:

For a Two-Player Game © Clear cover for the control panel © Control-panel decal

  • Five blue pushbutton assemblies
  • Five yellow pushbutton assemblies
  • Two Punch/Kick/Defend pushbutton decals © Two joystick assemblies
  • Twelve #10-2 washers, and nut/washer assemblies — four for the comers of the control-panel cover and eight for the joysticks. x %Hong black carriage bolts, fat

Installing the Parts for a Two-Player Game

  • Using carbon paper, transfer the control mounting pattern from the template to the control panel Save the template. Also refer to Figure 1-3 or 1 for the exact locations of all control panel holes.
  • Using a saber saw, carefully cut out the large hole for the joystick controls and the smaller holes for the pushbuttons. Deburr the sharp edges with a file.
  • Lay the plastic cover over the top of the control panel and mark the outside shape of the panel on the plastic. Also mark the button holes as close as possible to the locations shown on the template. Lastly, mark the positions of the four holes that will be used for securing the cover to the control panel. These four holes can be placed anywhere near the corners — wherever space permits.
  • Using a bandsaw, cut the control panel cover to its correct outside shape.
WARNING Wear safety glasses when drilling the plastic control panel cover. Use care to avoid shattering or chipping the plastic.

Tape or glue the template to the plastic cover. To art the saber saw cut, drill a 1/2” hole inside the joystick holes and the pushbutton holes.

  • Saw out the large joystick holes and the pushbutton holes.

1-5

Page 14

Carrer 1 = INSTALLATION GUARDIANS OF THE “Hoop Krr

Solder Side Component Side

Color’Signal PiColor'
BrownPOWERGNDA|14POWER GNDBrown
Brown?POWERGNDB|2POWER GNDBrown
Red+5VDC©3+5VDCRed
Red+5VDCD|4+5VDCRed’
Orange’-5VE5 -5VOrange
Yellow’+12VDCF6+12VDCYellow
—KeyH7Key-
Violet/White”COINCTR2J8 COINCTR1Blue/White
4NotUsedK|9 NotUsed_
WhiteSPKR-L|10 SPKR +Brown
—Not UsedM11 Not Used_
GreenVIDEO GREENN12 VIDEO REDRed
BrownVIDEO NEG. SYNCP13 VIDEO BLUEBlue
—NotUsedR|14 VIDEO GNDBlack
_NotUsed$|18 SELF-TESTWhite®
OrangeRTCOINT16 LT COINYellow
Yellow/BlackNot UsedU17 Not UsedWhite/Black
Yellow/Brown®RTPLYRUPJ.S.VW18 LTPLYRUP JS.White/Brown"
Yellow/Red*RT PLYR DOWN J.S.W19 LT PLYR DOWN JS.White/Red"
Yellow/Orange”RTPLYRLEFTJ.S.X20 LT PLYR LEFT JS.White/Orange"
Yellow/White*RT PLYRRIGHT JS.¥21 LT PLYR RIGHT J.-S.White/Yellow’
Yellow/Green’RT PLYR (Switch 3) STRONG/KICKZ22 LT PLYR (Switch 3) STRONG/KICKWhite/Green’
Yellow/Blue®RT PLYR (Switch 4) FAST/PUNCHa23 LT PLYR (Switch 4) FAST/PUNCHWhite/Blue
Yellow/Violet?.RT PLYR (Switch 5) STRONG/PUNCHb24 LT PLYR (Switch 5) STRONG/PUNCH — White/Violet
Yellow/Gray*RT PLYR (Switch 2) FAST/KICK¢25 LT PLYR (Switch 2) FAST/KICKWhite/Gray*
Gray/White”RT PLYR (Switch 1) START/DEFENDdi26 LT PLYR (Switch 1) START/DEFENDViolet’
Black/WhiteSWITCH GNDe27 SWITCH GNDBlack/White
Black/WhiteSWITCH GNDf28 SWITCH GNDBlack/White

Footnotes

1The colors listed are for reference only. They are the colors used on the JAMMA harness available from Atari 2Connect to the 5V GND (RTN) terminal on the power supply. However, if you have 12V GND, connect one of the wires at pin 1, 2, A, or B to the 12V GND terminal. 3Connect to the +5V terminal on the power supply. However, if your power supply has a + Sense terminal, connect to the + Sense. 4 Connect to the -5V terminal of the power supply. If -SV is not available, connect to the 12V GND or the 5V GND. NOTE: If you do not have or use -5V, the maximum power to the speaker will be reduced by half. 5Connect to the +12V terminal of the power supply. If your coin counter(s) require 12V, also connect to the + side of the coin counter(s) 6i you want to install a second coin counter, connect this wire to one side of the right 12V coin counter. Then clip R26 on the game PCB. Note: Do not use 24V counters. Connect the + side to +5V or +12V on the power supply, as appropriate 7Connect this wire to one side of the left 12V coin counter. Note: Do not use 24V counters. Connect the + side to +5V or +12V on the power supply, as appropriate 8Use this wire if you want an external self-test switch. However, the kit already has a self-test switch on the game PCB. (If you connect an external self-test switch, turn off the switch on the PCB. Connect the wire to the N.O. terminal on the external self-test switch. Connect the common terminal of the switch to a GND wire.) 8Connect these wires to the N.O. terminal of the control switches. Connect the common terminal of the switch to a GND wire. Refer to Figure 1-6 for proper switch connections.

Table 1-3 JAMMA Pin and Wire Connections

1-6

Page 15

Gvarbians oF THE “Hoop Kir CHAPTER 1 ~ INSTALLATION

Pin #Wire Code _SignInstructions
1BKGNDConnect to common terminal of player 3 control switches.
2RW=Not used
3W/BU=Not used
4WiGY—Not used
5wilyaNot used
6Ww=Not used
7BNPlayer3 UpConnect to N.O. Terminal of the joystick UP switch
8RPlayer 3 Down Connect to N.O. Terminal of the joystick DN switch.
9ORPlayer 3 LeftConnect to N.O. Terminal of the joystick LEFT switch.
10YPlayer 3 Right Connect to N.O. Terminal of the joystick RIGHT switch
1GN(Switch 5) STRONG/PUNCH
12BU(Switch 4) FAST/PUNCH
13v(Switch 3) STRONG/KICK~ Refer to Fig. 1-6. Route to N.O. terminal of
14GY(Switch 2) FAST/KICKappropriate switch.
15W/BN(Switch 1) START/DEFEND
NOTE: The center player is the “third player’.

Table 1-4 Third-Player Pin and Wire Connections

25" Dia. 1.75" Dia. A 1.18" Dia. (8 places) /~ (2 places) ' (10 places)

Suggested Distance from the tro: control panel,

Figure 1-3 Locations of Control Panel Holes to Be Drilled (Two-Player Atari Cabinet)

Page 16

Cuaprer 1 — INSTAL TION GUARDIANS OF THE “Hoop Krr

CL NOTE: Shaded holes should already exist dl 1.75" Dia, 1.18"Dia, | on Dynamo Cabinets. (2places) (10places) | 25" Dia. (8 places)

Suggested Distance 2.50" . 5.91" from the front of the . 1.50 i control panel. 5.91

Figure 1-4 Locations of Control Panel Holes to Be Drilled (Two-Player Dynamo Cabinet)

Controls

Video, Audio

Player 3 Controls

¢ Existing on Player 3 JAMMA Harness

Player 3 Connector JAMMA Connector

Figure 1-5 Correct Placement of Split Beads

1-8

Page 17
  • Drill the four 4” holes that will be used to mount the cover to the control panel and the holes to mount the joystick controls and pushbuttons.
  • To prevent injury, carefully deburr all the edges of the plastic cover.
  • Install the control panel decal on the control panel Use a sharp X-ACTO knife to trim the outside edge and to cut out the holes for the controls.

Mount the Punch/Kick/Defend decals on the control panel around the pushbutton holes.

  • Install the cover on the control panel with the four 3/4"-long carriage bolts, washers, and locknuts.
  • Install the joystick controls using the 3/4”-long carriage bolts and #10-24 nut/washer assemblies.
  • Install the pushbutton a emblies in Figure 1-1. For maintenance and servicing information on the joystick control, refer to Chapter 3 of this manual.

Connecting the JAMMA

Harness

  • If your game cabinet does not already have a JAM- MA harness, install a JAMMA harness in the cabinet (optional, Atari part no. A046501-01).
  • Install one pair of 0.50" split beads on the JAMMA harness (See Figure 1-5).
  • Install one pair of 0.40" split beads on the following harnesses (See Figure 1-5): ¢ The harness that runs to the power supply *¢ The harness that runs to the display speakers and coin door

¢ The harness that runs to the control panel. In all cases, make sure you move the split beads as: close to the PCB edge connector as possible. Hold the beads on the harnesses with the tie wraps included in the kit.

CAUTION You must install the split beads on the JAMMA harness to meet FCC requirements. GUARDIANS OF THE ‘Hoop Krr 4 CHAPTER 1 — INSTALLATION

4, Using Table 1-3 for wiring information, connect the JAMMA harness to existing component harnesses. Use crimp splices or butt soldering.

WARNING Do not simply tie the wires together. If you do, you could cause intermittent problems, loose connections, oxidation, or a fire.

Connecting Power Wires

  • Connect the wires on the JAMMA harness to the wires for the power supply, as shown in Table 1-3. The Guardians of the ‘Hood kit requires +5V and +12V. If -5V is available, it should be used, too.

iy Tie off any other voltage wires on the power supply besides +5V, -5V, and +12V. ch voltage in one wire for

  • There is more than one wire for the JAMMA harness. Use more tha each voltage (connecting them as described in Table 1-3) so that the power wiring does not overload and burn.

Connecting Video Display Wires

NOTE The JAMMA harness provides only negative composite sync. If your video display requires separate positive sync, see Chapter 3 for alternative wiring.

Connect the wires designated for the red, green and blue video guns along with the syne and ground wires, according to Table 1-3

Connecting Coin Door Wires

  • Connect the wires on the JAMMA harness to the coin switches and meter according to Table 1-3
  • Connect one terminal of the door lamps to one of the GND wires. Connect the other terminal of the door lamps to the R wire supplying +5V.
Page 18

Carrer 1 — INSTALLATION & GUARDIANS oF THE “Hoop Kir

NOTE Do not use -5V for the coin door lamps. The -5V is required for audio.

Some games have separate power supply outputs for the coin door lamps. If you choose to use these outputs, make sure you connect both terminals of each lamp to the terminals on the power supply.

Connecting the Control Wires

Connect the joysticks and switches to the JAMMA harness using crimp splices or butt soldering. Follow the wiring instructions in Table 1-3 and refer to Figure 1-6 for switch numbers.

Grounding the Cabinet

Find the ground lead (green) of the 115V input power thain fashion to a bare line. Connect this lead in cl metal part of the coin door, the control panel, the video display, and the power supply. This AC ground must be of #18 AWG wire or larger.

WARNING For the safety of players, you must connect the green ground wire as indicated above.

Checking the JAMMA Connections

Before plugging in the game PCB, turn on the power to the game, and check for +5V on pins 3, 4, C, and D of the JAMMA connector; +12V on pins F and -5V on pins E and 5. ; and

Check that the video display and the attraction lamp have power. Now turn off the power to the game.

Installing the Guardians of

the ’Hood Board Set

After you have checked the power on the JAMMA connector (above), install the Guardians of the “Hood board set in the cabinet. Follow these steps and referring to Figure 4-4: I. Use the nylon standoffs, fiber washers, and four 26 x 1%"long screws in the kit. Connect the JAMMA connector to the game PCB.

  • Secure the JAMMA harness away from the PCB with cable ties.

1-10 4, Turn on the power to the game. Check that the game PCBs function. If a video picture is not present, see Chapter 3.

Installing the Bezel, Decals,

Labels, and Attraction

Assembly

Installing the Product ID and FCC Label

the product ID label (part no. 038158-01) and > compliance label (part no. 039450-01) on the FC! back of the cabinet

Installing the Side Panel Decals

Find the side panel decals in the kit. Wet the left and right side panels of the cabinet with slightly soapy water. Then position the decals as shown in Fi 1-1. Remove any wrinkles in the artwork using a squeegee. Allow the sides to dry.

Installing the Attraction Assembly Find the Guardians of the “Hood attraction shield and the attraction panel film in the kit. Using the existir a template, cut the shield and film to size, if y. Install them on the cabinet as shown in Figure 1-1 shield as necess

Assembling the Three-Player Control Panel (Pit-Fighter)

NOTE To install the third player in any cabinet other than Pit-Fighter, you must first purchase an additional joystick and five red button assemblies from Atari Customer Service; then follow the installation instructions by using Table 1-4 as a reference.

Parts Needed from This Kit

To assemble the three-player control pancl, you need the optional three-player control panel hole-cutting template. (The three-player template is a foldout included with this manual.) You will also need the following parts from the kit:

Page 19

For a Three-Player Game ©) Third-player harness assembly ¢ Two red pushbutton assemblies, © Punch/Kick/Defend pushbutton de © Two jumper harnesses

Disassembling the Pit-Fighter Control Panel Assembly

Modifying the Pit-Fighter Control Panel Assembly

  • Remove all the controls from the Pit-Fighter control panel assembly. Save these parts. Separate the metal control panel from the wood backup board by removing the seven screws around the perimeter. Mark the top surface of the backup board to avoid improper assembly later in the conversion process.
  • Remove the old decal from the Pit-Fighter control panel
  • Align the large template provided over the Pit- Fighter panel and tape it in position. Center-punch the 12 hole centers for the new button locations. Using a compass or circle template, draw the twelve 13/16" circles in pencil. Save the template since you will need it to make the plastic over!
  • Using a saber saw, carefully cut out the 12 button a 1/2" hole within the button hole outline to start the saber saw cut holes. If nec sary, first drill
  • Install the new control panel decal on the modified control panel. Use a sharp X-ACTO knife to trim the outside edge and to cut out the holes. ya Apply the three Punch/Kick/Defend decals on top of the control panel decal. Position the decals so that the holes in the label align with the new button holes in the metal panel.

Making the Plastic Overlay

  • Tape the template onto the 32 1/2" x 14" polycarbonate panel provided. Center-punch the 41 holes required. ng a compass or circle template, draw the appropriate size circle in pencil. Also trace the outside outline. Take your time and check your work ci template since you will need it to modify the wood backup board. irefully before proceeding further. Save the
  • Drill out the smaller holes using a power drill and appropriate size drill bit. For the larger holes drill a GUARDIANS OF THE Hoop Krr & CHAPTER 1 — INSTALLATION

1/2" hole within each, and then cut out with a saber saw.

Using a bandsaw, cut the control panel cover to its correct outside shape. arefully deburr all the edges of To prevent injury, the plastic overlay

Modifying the Pit-Fighter Wood Backup Board

Align the template on the fop of the wood backup board and tape it in position. Using a sharp pencil or other pointed object, poke through the template and mark each corner (21 places) of the new cutout, Then remove the template and “connect the Compare your outline with the template before proceeding further dots.”

Using a saber saw, cut out the center of the backup board following the outline transferred from the template.

Assembling the Guardians of the ’Hood Control Panel Assembly

we

6.

xn Remount the metal control panel on top of the wood backup board. Position the plastic overly over the metal panel, and check to see that all the holes are properly aligned. Then reinstall the seven screws around the perimeter to hold the assembly together. Mount the controls onto the panel using the parts and hardware provided in the kit as well as one joystick and three red buttons from Pit-Fighter. Install the blue buttons in the left-player position, the yellow buttons on the right, and the red but tons in the center.

Reinstall the Pit-Fighter control panel harness Install the two kit switch jumper harnesses (Atari part no, A050194-01) and plug them into the two block. yle connectors. © Plug the gray wire into pin 9

  • Plug the white wire into pin 10 Route the one-player wires (white with colored stripes) into the one-player switch Route the two-player wires (yellow with colored stripes) into the two-player switch. Leave the existing ground (green wire) attached. Splice the switch ground wires from the nearby switch (COM),

Lil

Page 20

CHAPTER 1 — INSTALLATION & GUARDIANS OF THE “Hoop Kit

  • Rearrange the original three switches to their correct placements, following Table 1-3 and Figure 1-6.
  • Be sure to install the split beads included in the kit. See Figure 1-5 for the correct placement of the split beads.

Connecting the Three-Player Harness

When you install the three-player harness in your game cabinet, you must:

  • Remove the existing harness from the three-player switches.
  • Add the three-player kit harness
  • Rearrange the switches Follow these steps (See Figure 1-6):
  • Clip some of the tie wraps attached to the existing three-player harness and remove this harness.
  • Install the kit three-player harness (Atari part no. A049811-01) and route it to the appropriate switches by referring to Table 1-4 and Figure 1-6.

Setting the Coin and Game Options

Set the coin and game options in the self-test. See Chapter 2 for information about the option settings.

178237-005 178237-001 Biue Button Assy. Red Button Assy. (Splaces) ( places)

START/DEFEND

" FAST/KICK

y / 7 3 / STRONGIKICK 3 73 / 5. 4 im (3

178237-002 4 3 Yellow Button Assy. (5 places)

Ground x STL ‘STRONG/PUNCH White Wire FAST/PUNCH

to No. 1 Switch of Yellow Buttons | Gray Wire to No. 2 Switch of Yellow Buttons

| Top view, detail of the connector

Player 3 Player2 Player 1

Figure 1-6 Connections for Optional Three-Player Harness

7-12

Page 21

Maximizing Earnings

For maximum earnings, regularly maintain your Guardians of the ‘Hood game following the instructions shown in Table 3-1, in Chapter 3. When you set up the game and when you collect money, perform the automated self-test and check the controls with the Controls ‘Test in the self-test.

You should read Chapter 2, Self-Test, for information on the game options, statistics, and coin options so you can effectively use the available options. Evaluate the game data by using the statistics and histograms. screens, and make adjustments on the game options: screen

The key to maximizing earnings is striking a midpoint on game times. Game times must be short enough so that the player turnover is high. Conversely, game times must be long enough to give players a good value and ensure repeat play, Repeat play is crucial to longevity. The Guardians of the ‘Hood software gives the operator the flexibility to tune game difficulty and enough statistics to intelligently make adjustments. If collections seem low or are dropping off, cheek all player controls and coin mechanisms for proper ope ution

If carnings seem low, the game is technically sound, and the average game time per quarter is under 150 ulty option to an seconds, try changing the game diffi easier setting. The change will give players more game time for their money

If the average game time per quarter is over 270 seconds, first try changing the game difficulty to a harder setting. If the average game time per quarter is still over 270 seconds after a few weeks, try an even harder setting After changing the game difficulty setings, you should reset the game statistics and the histograms. The game statistics and histograms can be cleared in the self-test by holding the start button and pressing any left button

Game Play

This Guardians of the Hood” game ection describes the features and play of the

Introduction

The place is Center City. An escalating crime rate has converted a once-peaceful town into a seedy hangout for gangs and hoodlums. Ganpiass of tHe Hoop Ker CHAPTER 1 — INSTALLATION

Three gangs have taken over the town — the Dreads, the Shavers, and the Dragons. E: boss that rules over them. The plan for the Guardians: of the ‘Hood is to break up the gangs and convert the ich gang has an evil

bosses to their side. Only this way can they turn the tide and regain the city, In the end, the secretive “Mr, Big” unveils his true identity that will surely surprise every player. The local gym has become a meeting spot for a band of young citizens called the Guardians of the “Hood Here they work out and train with cach other to keep. their fighting skills razor sharp and instincts cat-like keen. Each could be registered as a lethal weapon, and united their fires burn hotter than boiling lava and pump up to the strength of one hundred men

Game Characters

‘The characters in Guardians of the ‘Hood are

© CONNER — An all-around good fighter. Trained in both boxing and Karate, he possesses amazing quickness for his size. Graduating with honors from Center City University in medicine, he is considered the most cligible bachelor of the town © CHIEP — Tough as a truck and the size of three men. Afier losing his family in a battle between two rival gangs, he pledged to bring back peace to the city. He is so devoted to the cause. that he passed up & multi-million-dollar football offer © TANYA — She is the tall statuesque cat, When not securing the peace in Center City, she can be found adorning the covers of major fashion magazines. Her father’s duty in Special Forces influenced hi ws black interest in the martial arts. She posse belts in Tai-Chi, Tae Kwon Do, and Kung Fu © JAVIER — He is a gold-medal winner in kickboxing. His natural speed and agility aided his ability to be a multi-sport athlete. Afier the Guardians of the ‘Hood clean up the city, he plans to return to his shortstop position on the Center City Bashers.

Game Play Description

Guardians of the ‘Hood is a two-player game (expandable to a three-player game) full of hard-hitting action Players wage the war against crime with four powerful fighters. As players punish rival gang bosses and convert them to their side, the selection of player characters increases. There’s seven in all! From closed-in Gym Waves to wide-open street scenes, Guardians of the ‘Hood gives playe head-to-head and side-scrolling game play: Meet heads the best of both worlds.

Page 22

CHAPTER 1 — INSTALLATION & GuarbIANS OF THE “Hoop Ket

on with gangs who make bad streets, back alleys, and subway stations their domain to prey on the weak! Players can even pick up and use street junk like and garbage cans, parking meters, newspaper stands, even car fenders! Four pushbuttons in combination with the Defend button (a total of five) arm each fighter with over 35 different moves. A devastating Power Move is executed

1-14 when all pushbuttons are pressed. There are lots of hidden moves for players to discover! The new power-perfect 3-D digitized graphics make the action almost too close for comfort! But you be the judge of that! Don't turn your back on those that need you ... help save the city! Who knows, hero, you may see yourself on the front page!

Page 23

1-15

of the ’Hood™ Kit Control Panel (Atari Cabinets)

GAMES

GUARDIANS OF THE Hoop Kir & € Es f H z g

Page 24

CHAPTER 1 — INSTALLATION & GUARDIANS OF THE "Hoop Krt

1-16

Page 25

Granbiays oF THE Hoop Kee CHaprer 1 — INstan.ation

Figure 1-8 Two-Player Hole-Cutting Template for Guardians of the ’Hood™ Kit Control Panel (Dynamo Cabinets)

ATARI

GAMES

Top

® © DOD FDO

_O

NOTE: Shaded circles represent existing holes in the Dynamo control panel.

L-17

Page 26

CHAPTER 1 — INSTALLATION & GUARDIANS OF THE 'Hoop KIT

1-18

Page 27

CHAPTER 2

Self-Test

SE THE Guardians

of the ‘Hood self-

test to check the when you first set up the

game, each time you collect

the money, or when you

condition of the game circuit-

ry and controls. You will see the self-test in-

formation on the video display and hear the

sound test information through the speakers.

‘You do not need any additional equipment to

perform the self-test. #7” Perform the self-test suspect game problems. This

chapter shows the screens in the self-test and

explains each of the tests. The screens and

explanations are arranged in the order they

appear in the self-test. Table 2-1 lists all the

self-test screens.

Page 28

g-Test & Gragpiays oF tae “Hoon Krr Cuaprer 2 -§

Entering and Ex the Self-Test

This game has two self-test switches. The primary one is conveniently located inside the upper coin door (inside the left edge of the opening). The secondary sell test switch is located on the JSA Audio HT PCB, in the drawer behind the control panel

iting

To enter the self-test, turn on the self-test switch inside the upper coin door, Doing so displays the Select Test menu (entitled “Self Test”): see Figure 2-1. Exit the self-test by turning off the self-test switch at any time.

RAM and ROM Test

When you turn on the power, the game automatically runs through the random-ac memory (RAM) and read-only memory (ROM) test. This test is not part of the self-test procedure. Regardless of whether or not the game has a problem, it will always advance to the attract mode. The game will stop only if you power it

Self Test (Select Test Menu)

Switch Test

Volume Adjust

Sound Test

Coin Options

Game Options

Game Statistics

Alpha(numeric) Test

Motion Object Test

Playfield Test

Color Test First Color Test Second Color Test Red Color Purity Green Color Purity Blue Color Purity White Color Purity Grey Color Purity

Convergence Test White Convergence Violet Convergence Blue Convergence Yellow Convergence

Table 2-1 Summary of All Self-Test Screens up and the self-test switch has been previously turned on

Game RAM Test

No message appears while the test is checking the RAMs. If more than 30 seconds clapse and the self-test menu doesn’t appear, the game has a problem. See Table 2-2 for the locations of bad RAMs. If the test finds no RAM erre gram goes to the ROM test after 15-20 seconds

Game ROM Test

If the test finds no ROM errors. no Message appears and the program goes to the tithe screen in the attract mode. [f a ROM fails, a message is displayed. Furthermore, if the failed ROM is a program ROM, then the error number with checksums is shown in the center of the screen. The ROM error test takes a few seconds: See Table 2-3 for the location of bad ROMs. s, NO Message appears and the pro-

If you think you have a ROM error, but the screen shows no messages, see Table 3-3 for information about the locations of various ROM functions

Depending on how bad the ROM error is, you may not be able to enter the self-test

Select Test Menu

Choose which test or screen you want to see from this: menu, shown in Figure 2-1. Move up and down the menu using any joystick. Start the selected test by ng any Defend button

RAM Location

Error AddressHighLow
FE8000 (Color RAM)3C20
FFOO00 (Video RAM)17N15N

Table 2-2 Bad RAM Location by Error Address

ROM Location

Error AddressHighLow
0000008D8C
0200009D9C

Table 2-3 Bad ROM Location by Error Address

Page 29

SELF TES SWITCH TEST

JOYSTICK=SELECT TEST DEF=DO TEST

Figure 2-1 Select Test Menu Screen

Switch Test

The switch test screen for a two-player game is shown in Figure 2-2. Test the joysticks and pushbutton switches. As you use each control, the pink Xs for the pushbuttons change to Os, or the joystick switch markers (small yellow dots) are highlighted. If the changes do not appear on the screen, check the switch wiring and the switches

NOTE The coin mechanisms are checked in the Sound test. See the section that follows.

Press the Punch and Kick buttons simultaneously to return to the select test menu

SWITCH TEST LABEL ADDRESS SWITCHO DATA E00000 Eo0002 E00010 £00012

00000000 00000000

DEPRESS PUNCH & KICK TO EXIT

Figure 2-2 Switch Test Screen Guarbians or THE “Hoop Kir %& Cuaprer 2 — Senr-Test

Volume Adjust

Adjust the volume of the game using this screen, shown in Figure 2-3. Follow the instructions at the bot tom of the screen to change the volume, to restore the old volume level, and to save the new volume and return to the select test menu.

DJUST VOLUME

VOLUME: 8

USE JOYSTICK TO CHANGE VOLUME

PUSH KICK TO RESTORE OLD VOLUME

PUSH DEF TO SET NEW VOLUME AND EXIT

Figure 2-3 Volume Adjust Screen

Sound Test

The sound test indicates the condition of the sound effects circuit on the game PCB. The sound test screen appears in Figure 2-4

Use one of the joysticks to select from the sounds; press one of the Punch buttons to listen to it. (You can have numerous sounds playing simultaneously, or you

SOUND TEST

4 MUSIC CHIP TEST

NUMBER OF SOUNDS 158 SOUND CPU STATUS Goop PUNCH=PLAY KICK=STOP DEF=EXIT

COIN MECH SWITCHES: LEFT RIGHT ° °

Figure 2-4 Sound Test Screen

Page 30

Cuaprer 2 - Senr-Test % Gt FANS OF THE “Hoop Kr

Option Available Settings

Free Play No Yes Explanation

Lets you choose free play to demonstrate the game:

Discount to Continue No + Yes

1 coin 1 credit # 2 coins 1 credit

Game Cost

8 coins 1 credit If set to Yes, this option reduces by 50% the player's cost to continue a game (always rounded up to the next full coin).

The number of coins required for one credit

Bonus for Quantity None + Buy-in 2 coins give 1 3 coins give 1 3 coins give 2 4coins give 1

9 coins give 2 9 coins give 3 Lets you choose from various kinds of bonuses or no bonus.

1 coin counts as 1 coin + 1 coin counts as 2 coins

Right Mech Value

  • coin counts as 7 coins 1 coin counts as 8 coins The number of coins each coin counts as in the right coin mechanism.

Left Mech Value 4 coin counts as 1 coin + 1 coin counts as 2 coins

1 coin counts as 7 coins 1 coin counts as 8 coins The number of coins each coin counts as in the left coin mechanism.

+ Manufacturer's recommended settings

Table 2-4 Coin Option Settings

can have silence, depending on which ones you select.) Pressing any Defend button returns you to the select test menu. COIN OPTIONS

Free Play:

count to continue:

Coin Options

Check and select the coin options on this screen, shown in Figure 2-5. The sereen shows the factory default settings in green, Game cost:

Bonus for quantity buy.

To move through the options, to change or save the settings, or to return to the select test menu, follow the instructions shown at the bottom of the screen. The coin option settings, with defaults, are shown and explained in Table 2-4 Right Mech Value:

Left Mech Value:

UP-DOWN SELECTS OPTION RIGHT-LEFT MODIFIES OPTION KICK RESTORES FACTORY SETTINGS START TO SAVE & EXIT

Figure 2-5 Coin Options Screen

Page 31

Available Settings

Scale of 1 to 8 (where 1 = Easy and 8 = Hard) 5¢

Attract (Mode) Yes + No Auto Clear High Scores Yes ¢

Cabinet Configuration = Tw Player + ~ Three- “Player

Clear High Scores Now Yes

Display EPA Screen Yes + No

Grardiass or tii “Hoop Ker CHaprer SeLE-TEst

Explanation

Sets the game difficulty.

Lets you turn the sound on or off in the attract mode.

Sets the number of players who can use the game. Automatically clears the high score table periodically. Immediately clears the high score table in the self-test.

Periodically displays the U.S. Environmental Protection Agency (EPA) emblem and the message “Recycle, Don't Trash It!” in the attract mode. If this game is used outside of the U.S., we recommend you set this option to “No.”

+ Manufacturer's recommended settings

Table 2-5 Game Option Settings

Game Options

Check and select the game options on this screen, shown in Figure 2-6. The screen shows the factory default settings in green.

To move through the options, to change or save the settings, or to return to the select test menu, follow the instructions shown at the bottom of the screen. The me options, with defaults, are shown and explained in Table 2-5.

GAME OPTIONS

DIFFICULTY LEVEL:

MUSIC IN ATTRAC’

CABINET CONFIGURATION:

AUTO CLEAR HIGH SCORES:

CLEAR HIGH SCORES NOW:

DISPLAY EPA SCREEN:

UP-DOWN SELECTS OPTION RIGHT-LEFT MODIFIES OPTION KICK RESTORES FACTORY SETTINGS START TO SAVE & EXIT

Figure 2-6 Game Options Screen

Game Statistics

Use the information shown in the four statistics and histogram (bar graph) screens to keep track of your game use and maximize your profits. Record the information on the Guardians of the ‘Hood statistics page in the back of this manual. The first of the screens is shown in Figure 2-7. The game statistics are collected from the last time the statistics were cleared, You can clear the statistics by pressing the Punch button. Press any Defend button to advance to the next statistics or histogram screen, or to go back to the select test menu.

STATISTICS

LEFT COINS: RIGHT COINS:

CONT GAMES: NEW MINS: CONT MIN! ERROR COUN’

TOTAL CREDIT: AVG TIME/CREDI AVG TIME/NEW GAMi 60 SEC AVG TIME/CONT GAMI 90 SEC O2MAR1992 0: O2MAR1992 06:56: oa

PUNCH TO CLEAR STATS START FOR NEXT SCREEN 78 SEC

Figure 2-7 Statistics Screen

Page 32

Cuaprer 2 — SELF-Test & GUuanbians or Hr ‘Hoop Kit

First Statistics Screen

The first statistics screen lists the following information: © Left Coins shows the number of coins counted in the left coin mechanism. © Right Coins shows the number of coins counted in the right coin mechanism. the number of coins countice coin inputs.

  • Auxiliary Coins show ed on the auxiliary sen © 0 Plyr Mins shows the number of minutes that the game was idle.
  • 1 Plyr Mins shows the number of minutes that the game was played by one person only. © 2 -Plyr Mins shows the number of minutes that the game was played by two people.
  • 3 Plyr Mins shows the number of minutes that the game was played by three people © Session is measured from when the first play starts a game until the Game Over message appears. ¢ New Games shows the number of unique games played. A unique game is counted every time a play: { ‘ er starts a new game (not a contin- é ued game).

© Cont Game: &f shows the number of games that players continued. ¢ New Mins shows the number of minutes that the game was played as new games. ¢ Cont Mins shows the number of minutes that the game was played as continued games.

  • Error Count shows the number of errors counted in the erasable memory. If you have an error count, the statistics may be wrong. If you consistently have errors counted for several weeks, replace the EEROM at 30E on the Guardians of the "hood game PCB. © Total Credits is the number of credits accumulated by the game.
  • Average Time per Credit is displayed in seconds. This item is tabulated for all games played since the statistics were cleared. If there are no credits, this line will not be displayed

‘Time per New Game is also displayed in

seconds,

  • Average Time per Continued Game is also displayed in seconds. Statistics 2 Screen

The next statistics screen (titled “Round Counts and Average Times”) lists the locale of each round. After the 13 locales, the screen shows how many players achieved those rounds and their ave times playing those rounds

New Game Time Screen

The next statistics screen (titled “New Game Time in Seconds”) lists the length of time for all new games, grouped in 20-second increments (except for the shortest games lasting 0-39 seconds).

Continuation Game Time Screen

The next statistic en (titled “Continuation Game Time in Seconds”) lists the same information as the previous screen, except for continued games

Session Time Screen

The next statistics screen (titled “Session Time in Minutes’) lists how long each session lasted The bottom of the screen displays the median point for all session times. The median point represents half of all players above this point and half below,

Segment Screen The next statistic reen (titled “Segment at Which Player Quit”) lists which game segments players reached. The bottom of the screen displays the median point for all attained game segmen

Wave 1-4 Screens

The remaining four statistics screens (titled “Who's the most popular — Wave 1-4") | which ch: were most often chosen by players at the start of each wave. cters:

Alphanumeric Test

The alphanumeric test Figure checks the condition of the alphanumerics in the game. If you see an error on the screen, check the EPROM at 15L. Moving any of the joysticks up or down scrolls the screen up and down. Press any Defend button to go to the select test menu.

Motion Object Test

The motion object test screen, shown in Figure 2-9, tests the movement and color of various game objects. The most important part of this screen is the ROM sta-

Page 33

Figure 2-8 Alphanumeric Test Screen

Figure 2-9 Motion Object Test Screen

es should all tus squares on the right side. The sq be green (indicating good motion object ROMs); red squares indicate bad ROMs. The squares are displayed the same way as the ROMs are installed on the game PCB — columns S and P and rows 9 to 2 Choose an object and move it or change it as follows Control: This action results: Left joystick Left/right and up/down moves the object around on the screen Up/down enlarges/shrinks the object Right joystick

Selects one of the three motion objects (called 0, 1, and 2). Left Punch, Kick

Right Punch, Kick Selects a picture that will be displayed and manipulated as the motion object cMaprer 2 -Test GUARDIANS OF THE “Hoop Ket

Figure 2-10 Playfield Test Screen Press any Defend button to go to the sclect test menu

Playfield Test

The playficld test screen, shown in Figure 2-10, tests the movement of the playficld Move the left joystick up, down, left, and right to check whether the whole picture moves accordingly Press any Defend button to go to the select test menu

Color Test

This test has seven screens, the first of which is shown in Figure 2-11. Advance to each screen by pressing the Kick button. © The first color test Cabeled “0-RGB") indicates the dynamic range of the video display color circuit

Figure 2-11 Color Test Screen

tu

Page 34

CHaprer 2 — SELP-Test & Guaxpiays or tir “Hoon Krt

The screen should show four bands (red, green, blue, and white, from top to bottom), ranging from bright to dark, left to right. The red, green, and blue bands are produced by only one color gun being turned on in each band. At the bottom is a white band, in which all three color guns are turned on. ¢ The second color test (labeled “I1-YCP") shows the same as the first color test, but with two color guns being turned on in three bands a yellow band (red and green guns), cyan band (blue and green guns), and purple band (blue and red guns), At the bottom is a white band.

  • The remaining screen numbers 2 through 6 are color purity tests. The rectaneles of color shown are red, green, blue, white (GREY Purity 1”), and grey GREY Purity 2°). ach s color, with no curving at the corners, no unevenness of color, and no lines in the display. If any of these ens are not correct, adjust the video display as described in the video display manual. Return to the select test menu by pressing any Jab button.

Convergence Test

The convergence test has four screens — white, violet, blue, and yellow grid lines. The white screen is shown in Figure 2-12. To see the remaining screens, press any Kick or Jump button. Press any Jab button to go to the select test menu een should display a straight rectangle of Figure 2-12 Convergence Test Screen

Check the following on the screens:

  • The grid lines should be straight within 3.0 mm and the lines should not pincushion or barrel. © The convergence of the lines on the violet and black screens should be within 2.0 mm.

If these screens do not meet these criteria, adjust the video display as described in the video display manual.

Page 35

HIS CHAPTER con-

tains troubleshoot-

ing tables and re- TAPTER 3

Troubleshooting and Maintenance

pair procedures for your Guardians of the

Hood" game. The chapter has two parts. The

first part contains three troub!

bles. The tables contain genera eshooting ta-

troubleshoot-

ing information, the voltage levels and test ic ROMs to ¢

part of the c¢ points on the printed-circuit

boards, and a list of ROM-

caused problems, with specif-

heck and replace. a The last

rapter has information about

connecting the video display Cif it requires

separate positive sync) and repair information

for the joystick controls

Page 36

CHAPTER 3 — TROUBLESHOOTING AND MAINTENANCE GrakbiANs OF THE “Hoop Kit

Problem Suggested Action

Coin Mechanism Problem 14. Check the wiring to the coin mechanism

  • Check the voltage to the + side of the mechanism

3. Test the coin mechanisms with the controls test screen in the self-test

Check the harness and connectors. Perform the self-test. Check the voltage levels on the PCB. See Table 3-2, Voltage Inputs and Test Points. Check What ROM Problems. Look Like, Table 3 3, for specific ROM problems. Game Play Problem

Check the harnesses and connectors. Check the switches on the control. If you took the control apart, have you reassembled it correctly? Make sure all the parts on the control are in good repair. Repair or replace parts. Is the "Cabinet Configuration” option in the self-test game options set correctly? OTE: The @ joysticks and three- button switches do not require lubrication.

  • Is the speaker volume turned up? (Volume is adjusted digitally in the self-test.)
  • Check the voltage on the JAMMA connector.
  • Check the wiring from the PCB to the speaker. Control Problems (Zraens (Rona

Sound Problem

Check the voltage level to the PCB. See Table 3-2, Voltage Inputs and Test Points. Replace | the speaker. Video Display Problem

Screen is dark.1.Is the game plugged in?
  • Is the game turned on?
  • Are the connections good?
  • Is the line fuse good?
  • Is the display brightness turned up?
  • Are the solder connections on the line filter and transformer good?
  • Is the JAMMA connector on the PCB tightly connected?
  • Check all of the items below. If you answer no to any question, you have a problem with the video display, not with the game circuitry. See your video display service manual a. Do you have power to the video display? b. Are the video display’s filaments lit? c. Do you have high voltage to the video display?
  • Are the voltage levels to the video display PCB correct? (Power voltage is 100 VAC or 110 VAC, depending on the type of video display. Video signal voltage is 0.5 to 3.5 Volts.) 10.If the level is not correct, check the connectors and the harness. Only a colored screen appears. You probably havea serious RAN RAM problem.
Display area wavers or1.Do you have correct power voltage to the video display PCB?

is too small 2. Do you have correct high voltage to the video display?

Picture is wavy.1.Is the monitor ground connected to the monitor?

2. Are the sync inputs connected 1 properly? horizontal or vertical yoke wires on the display

Picture is upside down When you serviced the ‘display, you connected the wires incorrectly. Switch the horizontal or vertical yoke wires on the display. Convergence, purity Use the screens in the self-test to adjust the video display. Use the adjustment or color problems. procedures in your video display manual.

Use the centering procedures in in your video display manual

Table 3-1 Troubleshooting Table

Page 37

GUARDIANS OF THE

Voltage Test Point or LED

+5 + 0.25 VDC +5V1

CRS5 LED (Game PCB) CR4 (Audio PCB) CR (Audio PCB) Source and Purpose Hoop Kir CHaprer 3 — TROUBLESHOOTING AND MAINTENANCE

Logic power from the switching power supply. Lights when 5 V is applied to the PCB and the reset (RST) jumper is open Lights when the +12 V supply is good Lights when the -5 V supply is good. Table 3-2 Voltage Inputs and Test Points on the PCBs

Problem ROM Causing the Problem Check the ROM at:

Program works, but motion objects or Graphics ROMs playfield is wrong Garbage on screen; program doesn't work. Processor _ Game program is erratic. Program ROMs ADPCM ROMs No sound or erratic sound. 14S, 18S (Game PCB) 4D, 8D, 10D (Audio PCB) 13F (Game PCB) 17E, 17J, 19E, 19J (Game PCB) 9B, 10B, 12B (Audio PCB)

Table 3-3 What ROM Problems Look Like

Video Display Sync Problems

This game board provides separate positive horizontal and vertical syne on a separate connector, for monitors: that will not work with the composite negative sync signal provided at the JAMMA edge connector. This connector Cabeled “Syne") is located near the edge connector. Pin 1 is horizontal sync, Pin 2 is vertical syne, and Pin 3 is ground,

Troubleshooting

The tables in this chapter (3-1, 3-2, and 3-3) can help you troubleshoot problems in your game. The troubleshooting table lists possible sources of problems in various parts of the game. The voltage inputs and test points can help you troubleshoot PCB problems. The ROM problems table can help determine exactly which ROM might be causing game play problems.

Removing and Replacing the Joystick Control

The joystick control is shown in Figure 4-2. If you have trouble with the joystick, make sure you have asto the instructions included Figure 4-2 sembled it properly. Rel with the joystick or s If you need to repair the joystick, first remove it from. the control panel. Disassemble it by removing the retaining ring at the bottom of the shaft. To replace any of the four switches, remove the two screws that secure each switch

ROMs and RAMs

If you have think you have bad ROMs or RAMs, perform the ROM or RAM test in the self-test procedure. If you have a ROM problem, see Table 3-3. For the location of all the ROMs and RAMs on the game PCB, see Figure 4~4

Page 38

CHAPTER 3 — TROUBLESHOOTING AND MAINTENANCE GUARDIANS OF TIP "Hoop Krr

, NOTES

Page 39

CH APTER 4

Parts Illustrations

INTRODUCTION

HIS CHAPTER pro-

vides information

you need to order

replacement parts for your

kit. Common hardware parts,

such as screws, nuts, washers, and so on, are

included in these parts

mw When you order parts, give the part num-

ber, part name, the number of this manual, illustrations. downtime and

bers are listed

this manual. and the serial number of

your game, With this infor-

mation, we can fill your

order rapidly and correctly.

We hope this will create less

more profit from your games:

Atari Games Customer Service phone num-

on the inside front cover of

Page 40

CHAPTER 4 — PARTS ILLUSTRATIONS GUaRDiays oF ne “Hoop Krr

Bul 050151-01 Control Pane!

050227-01 Control Pane!

050154-01

160044-001 Snap-Action Items Not Shown 4049811.01 ‘A050194-01 3rd Player Switch Jumpers Hamess Assy. Harness Assy (2 places) 178237-001 038158-01 Red Button Assy. Product 0. Label for Srd Player 03945001 (2 places) FCC Compliance Label 050154-01 141026-001 Button Labet 50° |.D. Split Ferrite Boad 141026-002 25°1.D. Split Ferrite Bead Parts provided for the 2 places} ‘optional 3 player ONLY. soe-003 40" LD. Split Ferrite Bead (6 places) 1™w:377 Guardians of the ‘Hood Kit Installation Instructions

75-5128 10 Black Carriage Bolt (B places)

Decal

Cover

ton Label (2 places)

switch 10 places)

178237-005 Blue Button Assy, iS places)

NOTE: \tems marked with an **" are not part of this Assembly. | 050152-01 | Bezel Wi 4 Graphics 178114-032 2° W. Polypropylene Tape

| 046928-01 Attraction Shield

050150-01 Araction Film

050144-01 Side Pane! Oecal (2 Places)

‘8050756-03 Board Set Assy ‘consisting of ‘A050335-XX" Guardians of ‘The Hood Game PCB Assy. (FSG42GRN) ‘8048973-01" SA IKI PCB Assy 178278-612" Nylon Standoff (2 places) 1700-536" 6-32 Nylon Hex-Nut (2 places) 178171-1612" 1/4" Round Standoff 172025-3606" 6-32 x 3/8 Pan-Ha. Screw (places) 175014-2021" 6 Flat Washer (2 places) 175017-3013" #86 Spill-Lock Washer (2 places)

178020-812 16 Nylon Spacer (4 places) 17504-7068 Washer (4 places) 72-66248,

178237-002 Yellow Button Assy. (S places)

Figure 4-1 6 x 1 112 |Pan-Hd, Screw (4 places)

Parts of Guardians of the Hood Universal Kit (Two-Player Shown)

A050170-01 A

Page 41

GUARDIANS 01 tHe ‘Hoop Krv & CHaprer 4 — Parts ILLustrations

99-215030 | Black Knob and Shaft

99-215032 Washer

go-zisost | Pivot Cylinder

99-215033 "| Hub

99-215018 |_ Spring 1" Diameter |

| 99-215035 Z-Stop

| 99-215034 | Bracket

99-215011 #8 x.75 Screw — (4 places) 160044-001 187 Microswitch

99-215010 #4 x .75 Screw (8 places)

99-215036 — Microswitch Actuator

99-215031 Pivot Cylinder 99-215015 E-Ring

Figure 4-2 8-Position, Gold-Contact Joystick Assembly 171099-001

Page 42

Hoop kre GUARDIANS OF THE * z z Cuaprer 4 — Parts

NOTE: The first six digits of each program chip in this drawing are all the same number — 136092. The remaining four digits following the hyphen are marked in this drawing. For example, the part number for the chip in location 2S is 136092-0041

1s ce EL sta

eae 8S @w

(eee

@ ace t¢00- te § oez @ sez eeo0- in Boze veo0- BTEC

@ s0z se00- le § 002 9¢00a

i

=O: 6D c 3 61

39S yo [atin @ Cem 8

lt 7 8 rr @i

cos mR) Ol

aa» Q@ ox @ 016 ezoo- ¢| Earoove zz00- Qe 1200-5| Gace ozoo-

Tar ae eG

Figure 4-3 Guardians of the ‘Hood Game PCB Assembly (FSG42GRN)

Page 43

GUARDIANS OF THE 'Hoop Kir CHapTEr 4 — Parts ILLUSTRATIONS

LMB¥O3 2 RVI G

  • 1D We, @ aI Bs he ena [5 tau g 8 Us wee gezu

@ ie E.

ve! bea boy oy CRT G3 aaa Paranntneaeelc nese: paul fe vooss 2 8 aD we Ug vooes 5 0 | Pie “ae gin lee sous a Tem ct As _) & ie gq LM3403 ag 8273 LH3403_ ay) - "3 so fog 2 ~ OD" of Fa] | ¢ usi74 3 IE 4 oO or ee {U1 4 Ls273 So 4ci 4Cz “A ; 282 8 g 208 RYT 4 Gs FE ck 4 (2 0000s uc Glos ATIIIIE a Ls24o0 136092-0080 12C 4 > a f ie Oe 2 ts374 ) i4A isc ? 13E OR

: F74 2 ur 0 a78 () 5 186085-1088 176 oe Og Pal LS74 g Ls138

  • 108 <5 tec SHARE is393 8 is7e Q 4 | z 198 19 0 136092-0081 196 08 Opa 15393 208 [ ] 5136085-2046 206 ony 7 3 + 61. ae. D [1] # Qo o ful

Figure 4-4 JSA Ill Audio PCB Assembly A048973-01 D.

Page 44

UARDIANS OF THE “Hoop Krr STRATIONS % HAPTER 4 — PARTS ILL

Page 45

CHAPTER 5

chematic Diagrams

INTRODUCTION

HIS CHAPTER the Audio PCB. The game

contains partial PCB and Audio PCB assem-

schematic dia- bly drawings are illustrated

grams for the Guardians of in Chapter 4, Parts Hlustra-

the “Hood” game PCB and tions

Page 46

Cuapter 5 - Sci MATIC DIAGRAMS “GUARDIANS OF ‘THE "Hoop Kir

wet ues

ont ue ut are ar

scree sercy acre acres acraz ocrat starz Stet.

ww tw i r + T 7 iad avo gave Seso ger fase gua fas few

fom fame [tame 1 ws

Cc H py} oe + aye 039 = a

pa PHT a pe pas Ts 1 + - cHoNO

TT se gasy fae f

H

t t

8.7015 rows 3.2013

aT

13/208,

Sesexeser™ ow

100 5 wreath Sd rot wae a ee I a are moe re ca

unt uss sawed OY

Page 47

GUARDIANS OF THE Hoop Kir 4 Cnaprer 5 — ScuEMatic DIAGRAMS

services

coiNa on3 pcr un acrTR3 an

perme nerc3 acriRe acre, crm crag ecrray STARTS 008-189

i i lo id wo fare bean baat aso ger pase dart a fi wa Fare are - Baro ao Faro Faro Faro wow 8d | Tal Tae imo aa : tare paneer i t t Too cy f t r 4 t ar, oe srt t t Fy aD erp —a; Ey + + " t a GE MPED sbi ype 108 i i T ik Tsar Lop doo Lor Lis tos tee hee teu + i Sa I Pr ene eee Tas T" Tes ge

F : - — sv az baer gan fae gms gars Lam 5308 a fara Mo fin Bin Bia Fao Fao i yea! BS Tar 1 Tas me tt ; t ce ve ELS Pay t AS Tae t 2

r t t wee wou

a ae t 00 : : + 7 1 sar teow bao tes oon i Pa eat cae T™ Tas 7 Ee | t + oo | i | are

ono

nav j i cate cmt Pea Bot, ceurn | Sout

Figure 5-1 Guardians of the Hood Game PCB Assembly Schematic Diagram (FSG42GRN) 050335-XX B

Page 48

Carrer 5 — Schematic DiaGrams Gvanpiaxs or tHE ‘Hoop Krt

~~

Los ar

+ 02 ce 2 00

tHesahse{TLee
ayoParasmoz
13]soritt ee
afakyToe
Hosakei ystee

S420 2a} S32 iz Re oe ecrera

mel ft xaK-—!

visoo

Figure 5-1 Guardians of the ‘Hood Game PCB Assembly Schematic Diagram (FSG42GRN)

as I SINC. our

vernc. our cz car bes oer J ibber eer chon

050335-XX v10%80

B

Page 49

GUARDIANS OF THE "Hoop Krr Cuaprer 5 ~ Scuemaric DIAGRAMS

NOTES

Page 50

Cnarrer 5 — SCHEMATIC DIAGRAMS GUARDIANS OF Tue “Hoop Krr

new fone one Rea anaes Fa3K

Re Les

aces se spurs

i

i Died er tor icee Lev gar ste oti see on SPST STS on

or g hal - Ld sity 1

GND AND AGND TIED INTERNALLY NEAR MSM629S sen

Page 51

GUARDIANS OF THE "Hoop Kir 4 CHapTER 5 — SCHEMATIC DIAGRAMS

FIDUCTAL Hee q © 4 Greowcin, rme | se | oi ripe risen oi Ea

Figure 5-2 JSA Audio Il PCB Assembly Schematic Diagram 048973-01 C

5-7

Page 52

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 53

GUARDIANS OF THE Hoop Kir 4 CHAPTER 5 — SCHEMATIC DIAGRAMS

ae oz2aKe| PL RorzeKe) eeens i seas oC seo ef te SHE Sise—Ef ie oe a Suze] aver Hart Sart—el te 3/6 Fos acer sore—Sy ts 10s Heo ais

easetetoe Psat

base] 1s vos eee muge

Gee—e| te1702see

swe Mor PES ee secret

sor eitieo : Hertel)

:2ammrad
sas —Soure Webe aeTDspe efits

sies—idark | yep bow Bons

pe pemcnlnf wentsore }sr
3wipesoi S420

sre—tle | pds seer Seoejs | ep dewe

SiteTepeswpe

ise _ ir

co

| i a

Lape 2p of ——_4Epbes mbt exune—tpon thi! EL Lace _|isre is if a

ma]

eo

rorerzl

Figure 5-2 JSA Audio Ill PCB Assembly Schematic Diagram 048973-01 C

5-9

Page 54

Carrer 5 — Scuematic DiaGrams & Guanpiaxs or tie Hoop Kr

u22|

| ape + a

||Unsans
ee cesioe |a4

Yehorr + Geaerr Shans]

| o

. \ { | «| i 1 Laz trades! ti | Nae i |

;:z a

Ras, aoe i Tae '

zie E |

oc} soceet TF Le owe

Page 55

GUARDIANS OF ‘THE ‘Hoop Kir & CHaprer 5 — Si HEMATIC DIAGRAMS

nes Ne ean roe etre

soci 7 peper cay am} sooo iiss 30 Sore—Syat 4a sore—tf3 30 seta 20

soreseiimaex

St aelesers || races Terr 1 ces me nes nae —

weeny:[pceggaert gt
ere|Testsaaaij
|Liea3ahnee
aad Scan}7

Figure 5-2 JSA Audio III PCB Assembly Schematic Diagram 048973-01 C

Page 56

Cuaprer 5 — SCHEMATIC DIAGRAM! Gvarpiays OF THE “Hoop Kir

NOTES

Page 57

Eee ee eee eel eee alee ele ele ele elrel el

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays and laser-video disc players (in games supplied with displays and video-disc players) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted. If the products described Seller's sole liability shall in this manual fail to conform to this warranty, be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are d jefective;
  • Such products are returned prepaid to Seller's plant, and
  • Seller’s examination of said products discloses to Seller's satisf: that such alleged d lefects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. In no event shall Seller be consequential damages. iable for loss of profits, loss of use, incidental or

Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms herein, this warranty is expressed in lieu of all other warranties expressed or implied, including th. implied warranties of merchantability and fitness for a particular purpose, and of all other obligation: s or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.

Pee eeeeelelelelelelel ele ele ele ele ele ele letra ele fel!

The use of any non-Atari parts warranty, The use of any non game and cause injury to you s may void your warranty, according to the terms of the of your Atari parts may also adversely affect the safe and others, Be very cautious in using non-At supplied components with our games, in order to ensure your safety Atari distributors are independ ment they may sell parts or acc Corporation cannot be responsible for the quality, part or any modification includ lent, being privately owned and operated. In their judg- \ fn Atari parts or accessories. Atari Games suitability or safety of any non-Atari essories other tha

ing labor which is performed by such distributor

Page 58

| Zt ax “ hy, . i 4 | ATARI GAMES CORPORATION i oe eee ; 675 Sycamore Drive yee i ¢ Py