CATHODE RAY TOMES

Zarzon

Satan of Saturn (set 1) (SNK, 1981) · Manual · 25 pages · 5 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

“ZARZON”™ -UPRIGHT

TABLE OF CONTENTS

ZARZON™ GAME SET-UP

A. Introduction

B. Game Inspection

C. Game Instalation

D. Dip Switch & Volume Control Settings

MAINTENANCE

A. Cleaning

2 9 Fuse Replacement

Video Monitor Removal

Video Monitor Adjustments (Separate Manual) (72-00003-001)

E. Fluorescent Bulb Replacement

F. Printed Circuit Board Replacement

ILLUSTRATIONS AND PART LISTS

Video and Cabinet Assembly

Coin Mechanisms and Front Door

Switching Regulator & Cabinet Parts

Control Panel

Mounting Chassis Assembly

CPU Board “A” & Component List

CRT Controller Board ‘‘B’ & Component List

Option Switch & Volume Contro! Locations

Wiring Diagram

PC Board ‘‘A” Schematic (FOLD OUT)

PC Board ‘‘B” Schematic (FOLD OUT)

Page 3

GAME SET-UP

INTRODUCTION

TAITO AMERICA'S “ZARZON’’™ is a video action game designed for ‘one or two players.

The object of the game is to get your spaceship to Saturn, then once on Saturn to destroy as many Satan's as possible. Additional bonus points can be accumlated by destroying the comet or attacking dragonflies. An additional spaceship is awarded if the players score reaches 5,000 or 10,000 points. (adjustable)

If the attacking UFO's or enemy rockets are destroyed points will be scored. The game progresses through 4 different screens.

GAME INSPECTION

TAITO AMERICA’S “ZARZON"™ game is ready to play when received. However, careful inspection is necessary to insure the game is in perfect condition. Please verify the following before turning the game on

Examine external parts for chips, dents, or broken parts, Open the service door and examine the following:

  • Plug-in connectors to make sure they are firmly seated
  • Speakers
  • Player Controis
  • Printed circuit boards making sure there is no damage to the components. Check for loose foreign objects especially metal objects which may cause electrical problems. Fuses, making sure they are firmly in the holders. Transformer Coin Mechanisms

{f problems occur or technical assistance is required, contact our Customer Service Department HOT LINE Toll Free 800-323-0666 (except Illinois). \llinois phone 981-1000 X 215.

The Video Monitor is properly adjusted before shipping. If there are any adjustments necessary refer to the Video Monitor Manual. (72- 00003-001)

POWER REQUIREMENTS

TAITO AMERICA’S “‘ZARZON''™ game is shipped ready for operation at 120VAC, 60Hz with a power consumption of approximately 250 Watts.

CAUTION

For safe operation it is recommended the cabinet be grounded. This game is equipped with a three conductor power cable. The third conductor is the ground conductor and when the cable is plugged into an appropriate receptable, the game is grounded. The off-set pin on the power cable’s three-prong connector is the ground connection

LOCATION SPACE REQUIREMENTS

Depth - 35” (87.5cm) Width - 24” (61cm) Height - 68” (171¢m) Weight - 300 Ibs. (135Kg) (Packaged Weight) INSTALLATION REQUIREMENTS

The following precautions should be followed when installing the game

Avoid rough handling of the game, the picture tube is fragile. Install the game on a level surface. Avoid installing the game where it may receive excessive sunlight or heat, to prevent the game from rising internal temperature. Do not install in a damp or dusty location. For a short time after connecting the power to the game, the picture may be temporarily distorted.

DIP SWITCH AND VOLUME CONTROL SETTINGS

DIP SWITCH SETTINGS TAITO AMERICA'S "'ZARZON"™ game provides the following option switches. See Figure 8. These options can be found on PC Board “A”’ Switch B.

NOTE

Remove power before making S.W. Adjustments

‘SW1 should be keptin the ON position. The only time it would be in the OFF Position would be for the cocktail table version.

‘SW2 and SW4 are for coin selection. These switches are preset at the factory for 1 coin - 1 play.

COIN SELECTIONsw2sw4
Tcoin- 7playOFF|OFF
1 coin - 2.playon|OFF
2 coin - 1playof| ON

TABLE 1 COIN SELECTION

‘SW3is used for addditional bonus spaceships. Once the players score reaches the set bonus he is awarded an additional spaceship. This is preset at the factory at 5,000 points.

ON 5,000 OFF 10,000

TABLE 2 BONUS POINT OPTION Sw3

SWS and SW6 are used for selecting the number of spaceships per game. These switches are preset at the factory for 4 spaceships. SPACESHIPS sws | SW6 3 orF | OFF

4ONOFF
5ofr|ON

TABLE 3 SPACESHIP SELECTION

  • SW7 & SW8 are not used at all and must be kept in the OFF postion.

VOLUME CONTROL SETTING

  • VR. AThis control is used to control the volume of the total game and is found on PC Board "B”. See Figure 8 volume goes down when turning as the arrow indicates
Page 4

MAINTENANCE All games require a certain amount of maintenance to keep them in good condition. A periodic check of mechanical controls would be be- Neficiicial to guarantee your game will be profitable.

CLEANING The exterior of the game, all metal parts and all plastic parts can be Cleaned with an non-abrasive cleanser. Caution should be used when cleaning the plastic, a dry cloth can cause scratches and result in a foggy appearance.

FUSE REPLACEMENT This game uses six fuses, 5 are located on the Switching Regulator. See Figure 3 for size and part number of fuses. One fuse is located on the Power Supply itself.

VIDEO MONITOR REMOVAL Ityou need to remove the video monitor, follow the instructions listed below:

CAUTION

It is recommended the game be left disconnected for at least one hour before removing the video monitor. This will probably discharge the video tube but extreme caution is still necessary.

Remove power from line voltage. Disconnect the monitor and cable connector. Remove wire cable clamp. Take out the two side bolts, one on each side of the cabinet. Lower the monitor to rest on the lower set of wood supports. Remove the four mounting bolts and disconnect the green ground wire. Slide the monitor out by pulling the monitor towards you.

CAUTION

Use extreme caution and do not touch electrical parts of the monitor yoke area with your hands or with any metal object in your hands! High voltages may exist in any ‘monitor, even with power disconnected.

VIDEO MONITOR ADJUSTMENTS

TAITO AMERICA CORPORATION presently uses either a Wells- Gardner Corp. or Electrohome Electronics 19” color video game monitor in the “‘ZARZON’™ upright game. Refer to the Monitor Manual for your specific video monitor. Be sure to heed all the WARNINGS and CAUTION INSTRUCTIONS provided before repairing or replacing your video monitor. (72-00003-001). FLOURESCENT TUBE REPLACEMENT

CAUTION

\f you drop a flourescent tube and it breaks it will explode! PLEASE USE CARE WHEN REPLACING.

“Remove the three screws from the marquee bracket, being sure to hold the glass while removing the screws

“Remove marquee glass and the flourescent bulb is accessible.

“With both hands turn the bulb toward you, carefully pull lamp out of famp socket,

PRINTED CIRCUIT BOARD REPLACEMENT

You may wish to remove the “‘ZARZON” printed circuit boards for replacement or repair. Follow the procedure below.

To remove “‘A’’ and “‘B” board, loosen the wing screw located on the top of the PCB Chassis. Then slide the stop bracket to the side and slide the PC board to be removed out of the guides.

WARNING

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. As temporarily permitted by regulation it has not been tested for compliance pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.

Page 5

VIDEO AND CABINET ASSEMBLY

TAITO

ITEMPART NO.DESCRIPTIONREFERENCE
147C00001-002 | Screened Acrylic Marquee Panel400073
227-00001-001 | Fluorescent Tube, Std., 15W.‘AA0S4711
342B00057-001 | Fluorescent Lamp Panel140006
426-00004-001 | Lamp Socket (Holder)113000
561C00007-001 | Marquee Retainer500024
626-00005-001 | Starter Socket114001
729-00003-001 | Starter114000
818-00002-001 | Ballast Transformer (220V,60Hz)010001
g61B00011-001 | ‘‘L” Bracket‘AAP13584

10 41B00002-002 | Cabinet Assembly or 41B00005-001 | Cabinet Assembly 63-00002-001 | “T"’ Molding 400007

1259-00008-001 | Clamp Fastener390002

13 47000002-002 | Cover Glass

1463C00003-001 | Monitor Shroud400005
1561C00016-001 | Glass Retaining Bracket500022
1644C00001-001 | Wheel Assembly520000
763B00005-002 | ‘*L"" Molding, Black, 22%” Long400031-A
1863B00005-003 | “‘L"’ Molding, Black, 33%” Long400031-B
1931-00001-001 | Wells Gardner Monitor, 19”620006
19431-00001-002 | Electrohome Monitor 19”620007
2060C00061-001 | Video Monitor Bracket500026,
2145-00001-001 | Anchor Plate600005-C
2245-00001-001 | Service Lock & Key600005
2342C00035-001 | Cabinet Back143003
2461B00027-001 | Grille500074
25500086Mounting Bracket TopAA013580
26500088Cash BoxAA028507
27400050Cash Case‘AA028506
28600007Lock PlateAA013593
29500089Cash Box DoorAA026512
30600006Lock (Cash Box) & Key"AA016545
31500060Coin Funnel
32500061Coin Funnel PlateAA013690
33115000Counter, 6V DCAA013608
34500091Counter Bracket
3563B00006-004 | U Channel400025
36500087Bracket, Bottom
3736-00005-001 | Counter Drive Credit Board800011

38 25-00014-001 | 10 Position Edge Connector

39500035,Credit Board Bracket
“4007-00031-001 | Chassis PCB Mounting85008

“41 08-00004-001 | PCB Set (Taito)

“4208-00006-001 | PCB Set (SNK)L

*Not Shown on Figure 1

Page 6

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 7

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 8

SWITCHING REGULATOR & CABINET PARTS

TAITO

TEMPART NO.DESCRIPTIONREFERENCE
136-00004-001 | Switching Regulator Assembly800010
2998702Shield BoxAA013613

3 22B00001-001 | Power Line Filter 4 26-00003-001 | Service Outlet 5 24-00002-002 | Fuse, 1.5 AMP, 3AG, Slo-Blo, 250V 5A 24-00002-001 | Fuse, 3AMP, 3 AG, Slo-Blo, 250V

624-00001-001 | Fuse Holder171000
735-00001-001 | Barrier Strip, 8 Position100027
842-00034-001 | Power Mounting Board850071
929-00005-001 | Switch, Interlock024001
1029-00004-001 | Toggle Power Switch021500
135B00002-001} Insulating Shield199015
1218A00001-001 Isolation Transformer010002
13998962Noise FilterAAT61017
14998703Shield Cover

15 61-00030-001 | Bracket Interlock Switch

Page 9

SWITCHING REGULATOR & CABINET PARTS

Page 10

CONTROL PANEL

TAITO

TEMPART NO.DESCRIPTIONREFERENCE
129-00011-001 | Joystick Assembly 2-Way850084

2 42D0058-001 | Control Panel (Wood)

361A00015-001 | Strike Hook390003
429-00009-001 | Push Button Assembly (White)BTKO0004

5 47C00007-001 | Dash Panel, Screened

Page 11

CONTROL PANEL

Page 12

MOUNTING CHASSIS ASSEMBLY

TAITO

ITEMPART NO.DESCRIPTIONREFERENCE
185007PC Board Guide “‘B"WTO 90008
261B00050-001| Stop BracketTUO 200010
3500059Shaft P C ChassisTVvO 20001

4 25-00015-001 | 44 Position Housing Connector

5500055,Plate ShieldCVO 300023

6 Overall Board Set 08-00004-001 | Taito “ZARZON''™ or 08-00006-001 | SNK ‘'ZARZON™

7850006PC Board Guide “A”AAO 19547 _

Item 6 may be 2 or 3 board set

Page 13

MOUNTING CHASSIS ASSEMBLY

Page 14

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 15

CPU BOARD “A”

LP 150k HEB pact x

Page 16

CRT CONTROLLER BOARD ‘‘B”

TAITO TAITO

TEM_|PARTNO. | DESCRIPTIONREFERENCE1eM | PARTNO. | DESCRIPTIONREFERENCE

ZARZON CPU PC BOARD ‘'B’” C16 99-AAT33152 | LS IC 74LS240

SOP | 99-AA055154 | Angle Pin Header-50Pinici7__| 99-aAT33156 | LS IC 7415156
DS| 99-AA052566 | Dip Switch DSS81c18__|99-aAT33170 | LS Ic 7418273
Isi___| 99-Aa044786 | IC Socket 16PIc19__|99-AAT33176 | LS IC 7418283
1S2___| 99-AA055103 | IC Socket 18P120 _ | 99-AAT32163 | Static Ram PD2114LC
1S3___|99-AA055787 | 1C Socket 24P1c21 | 99-AAT34105 | CRT CONTROLLER

1s4___ | 99-AA055812 | IC Socket 40P, IHOASSSE.

ict| eg-aata300r | Ls 1c 74LS00ROM1 | 99-997518 | P-ROM 2716 D or 135
12| 99-aat33003 | LS 1c 74LS02ROM2 | 99-997519 | P-ROM 2716 U or 136
13| 99-AAT33005 | LS Ic 74LS04ROM3 | 99-997478 _ | BIPOLAR ROM IM5610 (OR138)
ica| 9-AaT33009 | LS 1c 74508i99-AAT41326 | Cap Ceramic .220pf 50V
Tes| 99-AAT33011 | LS 10 74LSt10c299-AAT41399 | Cap Ceramic 100pf, 50V
1e6| 99-aaT33027 | LS Ic 74LS92¢399-AT41672 _| Cap Ceramic O.luf 50V
1e7| 9@-aaT33051TLS IC 741874Rt99-AAT51741 | Res, Carbon 100 ohm ¥4=5%
1c8‘99-AAT33062 | LS IC 74LS86R299-AAT51749 | Res, Carbon 220 ohm 4 +5%
ico}99-aat32020 | TTLIC 74101R3__|99-AATS1757 | Res, Carbon 470 ohm %=5%
1c10‘99-AAT33089 | LS IC 74LS125R499-AAT51765 | Res, Carbon 1K %4+5%
Tet}99-AATS3110 | 1S 10 7418155R5__|99-AATS1781 | Res, Carbon 47K ¥4-+5%
112 | 99-AaT33112 | LS 10 74LS157R6__|99-AATS1797 | Res, Carbon 22K ¥a+5%

ic13 | 99-AAT33118 | LS 10 74LS169 RB __| 99-AAT55068 | Resistor Block 2.2 ohmx8 114 __| 99-AAT33121 | LS IC 74LS166 Ic15 | 99-AAT33127 | LS IC 7418174

Page 17

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 18

BOARD

BOARD "

99-998912 TALTO 99-998910 SNK

99-998911 TAITO 99-998909 SNK OPTION SWITCH & VOLUME CONTROL LOCATIONS

Page 19

{ Veeqher | [Counter drive ia p.c. board jamb pylome

C.R.T. CONTROLLER | [ 36-00005-00} ad = yt

P.C. BOARD uv @Blu coin

FS Z

Po wee egy

ASSY. ce [O2BOH9DHGD c/O®SHOOOSSIC 19} x DOOO©OOD)

3 i

c 35 ae ‘mebors bh.

Wm furb=t39 >

meter

service

switch

power supply block

#NOTE

a ¥ if Or |! Gall [Emonitor ¥| ells fardner

right mov—| fire —

08-00004-00! 08-00006-00! * OTS emGke FODOS® fe See ets wie 7 Tb

ul a O0

gen, vid, red vid. vid. sync. —| blue vid. — iS outio out 3 \® I reset " — upeale fe 296 OR)" i co : transformer|I

+ UH |reguiator [Lon

iS Is ea S| orale G [2@800900e5900008: 36-00004-00! H_ssy, tS, Hv. tev, ‘ed 0.

Page 20

SUneMALY Uru BuAR # 1063

§ & en a Servercy

Al ROM}

  • to——Bog it a (CA) ern ews Press sv “=D Ke 8 0 Mor +5V cm

ie < ol a

E ZBREBRZES

ge er ¢ 8 a zERE

Page 21

‘SCHEMATIC CPU BOARD “A” 20F3

Page 22

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 23

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 24

EA) (3-42)

‘BS

(B:CQRAR: ay et Hire 4 : o Ha er (O cH a es i G-F2) ¥ sed n 745244

EQ He 67 npc)ars
toys a hanesata 27 val&
2 it ne) ©ine Yadae

tee i H Hobe

is (2-E4 22ADDRESS I '3-BSIRAZ—— (3-C5)RA1=—" (3-C5)RAQ’ 5 (2-D7X2-F2X3-F8) a

(2-ET)

Page 25

DUNEMALIL Uru oUAR 4 30F3

= B 8 EE. [3-3 = 46 3 BOA Bo