CATHODE RAY TOMES

Kangaroo TM-204 4th Printing

Kangaroo (Sun Electronics, 1982) · Technical Manual · 68 pages · 54 sections · original scan

Page 1
Scan of page 1

This page is a drawing, shown as the original scan.

Page 2

DISPLAY GAME SERIAL NUMBER LOCATION Your game’s serial number is stamped on a label on the outside back of the game. The same number is also on the chassis of the video display, power supply, Regulator/Audio II Printed Circuit Board (PCB), and the Central Processing Unit (CPU) and Video PCBs. Please mention this number when calling your distributor for service.

CENTRAL PROCESSING UNIT (CPU) PCB

POWER SUPPLY GAME SERIAL NUMBER IDENTIFICATION TAG

VIDEO PCB

REGULATOR/ AUDIO li PCB

Page 3

Operation, Maintenance and Service Manual

Complete with Illustrated Parts Lists

Manufactured under license from Sun Electronics Corporation

Page 4

Kangaroo™

© 1982 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.

The Kangaroo™ game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the new Copyright Act of 1976,

This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while iegal action is pending. If infringers are convicted, courts can order destruction of the infringing articles.

\n addition, the Act provides for payment of statutory damages of up to $50,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees, fines up to $25,000, and face an imprisonment of up to one year.

Atari will aggressively enforce its copyrights against any infringers. We will use ail legal means to immediately halt any manufacture, distribution or Operation of a copy of video games made by us. Anyone who purchases. such copies risks forfeiting such a game.

Published by: ATARI, INC. 790 Sycamore Drive PO. Box 906 Milpitas, California 95035

Lithographed in the U.S.A. 7L

Page 5

Kangaroo™

TERFERENC { I

to licensed communications services is not permitted by the FCC (Federal Communications Commission) \f you suspect interference from an ATARI game at your location, check the following: @ All grounds (green wires) in the game are properly connected as shown in the game wiring diagram, and @ The game's power cord is properly plugged into a grounded 3-wire outlet. If you are unable to solve the interference problem, please contact:

ATARI Customer Service (800) 526-3849 or (800) 538-1611

Notice Regarding Non-ATARI Parts

WARNING

Use of non-ATARI parts or modifications of your ATARI game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

The warranty printed on the inside back cover of this manual may be voided, if you do any of the foliowing:

@ you substitute non-ATARI parts in your coin-operated game, or

@ you modify or alter any circuits in your ATARI game by using kits or parts not supplied by Atari.

Not only may the use of any non-ATARI parts void your warranty, but any such alteration may also adversely affect the safety of your game and may cause injury to you and your players.

Page 6

Kangaroo™

Table of Contents

Set-Up Procedures A. B.

omm New Features 1-3 Game Inspection . 1-3 hae installation. . 1-3 . Installation Requirements . 1-3 2 Voltage Selection ....... 1-3 Switch Locations ... 1-4

  • On/Off Switch ... 1-4
  • Utility Panel Switches .... 1-4
  • Service Switch 1-4
  • Option Switches . 1-4 Option Switch Settings 1-5 Self-Test Procedure 16 Game Play 18
  • Attract Mode .... 18 . _Ready-to-Play Mode

High Score Mode 2.

  • Play Mode
  • Hints for Game Play

Troubleshooting A. Comments on Troubleshooting 2-2 B. Self-Test Procedure 22 C. Troubleshooting with the CAT Box and Z80 Interface Adapter 2-4 D, Glossary of Schematic Signal Descriptions 27

Maintenance, Repair and Parts A. Cabinet-Mounted Assemblies... ..........0 0.0.00 c cece cece eens 3-2 B. The Control Panel 0.0.2... 00. c cece cece eee eee ences 3-7 C. Fluorescent Tube and Speaker ......... 0... cece eee eee eee eee 3-12 D. Video Display . E. CoinDoor....... on F. Printed-Circuit Boards ......... 0... c cece cece cece eee tenes 3-21 G. Power Supply Assembly ........ 0.0.00 e cece eee eee eee eee 3-30

Page 7

Kangaroo™

List of Mustrations

Figure 1-1 Game Overview, Upright Cabinet .......... 0.0.00. e cece ee eee 1-2 Figure 1-2 Game Switch Locations .... +4 Figure 1-3 Self-Test Procedure ........ 16 Figure 2-1 Self-Test Screen 1—Test Passes 22

Figure 2-2 Self-Test Screen 1—Test Fails............ 20.0.0 c cee e eee eee 2-3 Figure 2-3 Self-Test Screen 2.1... .... 0. ccc e eee e eee ete ee eee 2-3

Maintenance, Repair and Parts: Figure 3-1 Cabinet-Mounted Assemblies, Upright Cabinet.................- 3-2 Cabinet-Mounted Assemblies, Ireland-Built Cabinet . 3-4 Figure 3-2 The Control Panel 3-7 Figure 3-3 Control Panel Assembly .. 38 Figure 3-4 8-Position Joystick Assembly... 0.0.0.0... cece cece eee eee 3-10

Figure 3-5 Fluorescent Tube and Speaker, Upright Cabinet ...............6- 3-12 Fluorescent Tube and Speaker, lreland-Built Cabinet ............. 3-14 Figure 3-6 Video Display..... 20.0... ieee cece eee tee ees Figure 3-7 Vertically Mounted Coin Door.... Figure 3-8 Printed-Circuit Board (PCB) Removai

Figure 3-9 Kangaroo Central Processing Unit PCB Assembly ..............5 3-22 Figure 3-10 Kangaroo Video PCBAssembly ...........-.45 Figure 3-11 Regulator/Audio!| PCB Assembly . Figure 3-12 Power Supply Assembly

Table 1-1 Option Switch Settings ........ 0... eee e cece eee eee Table 1-2. Kangaroo Scoring . . see Table 2-1 Display RAM ...... Table 2-2 Sound Microprocessor ..... Table 2-3. Display Addressing Memory Map . .

Page 8

Kangaroo™

If reading through this manual does not lead to solving a certain maintenance problem, call TELEHELP® at the Atari Customer Service office in your geographical area, as shown below.

WEST and CENTRAL U.S.A. Parts and Service

Atari, Inc. California Customer Service Office 1105 N. Fair Oaks Avenue P. O. Box 427, Sunnyvale, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Facific Time) From California, Alaska, or Hawaii (408) 745-2900 Service from anywhere in the area shown in white oltre (800) 538-1611

EAST U.S.A. Service only

Atari, Inc. New Jersey Customer Service Office 12A World's Fair Drive, Somerset, NU 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) From New Jersey ® (201) 469-5993 From anywhere else in this area toll-free (800) 526-3849

EUROPE

Parts and Service

Atari Ireland Limited European Customer Service Office Tipperary Town, Ireland Telex 28165 TIPPERARY TOWN, (Monday-Friday, 9:00-6:00 pm GMT) IRELAND

@ 06252155

vi

Page 9

Set-Up Procedures

How to Use This Manual

This manual, written for game operators and service technicians, describes the Kangaroo™ game.

The manual contains information about al/ Kangaroo cabinets. Whenever information is unique

to the Upright cabinet, this symbol appears: i Built cabinet, this symbol appears: he

Whenever information is unique to the Ireland-

Chapter One details new features, game set-up, option switch settings, self-test procedures, and game play.

Chapter Two includes troubleshooting procedures.

Chapter Three contains maintenance, repair, and parts information. In addition, schematic diagrams of the game circuitry are included with this manual. Figures 1-1 and 3-1 illustrate the game cabinet. Italicized lettering on these figures refers you to other places in the manual for information about specific cabinet parts.

Chapter

Page 10

Set-Up Procedures Kangaroo™

FLUORESCENT TUBE AND SPEAKER See Figure 3-5

COLOR VIDEO DISPLAY See Figure 36 ACCESS PANEL

POSITION JOYSTICK See Figure 3-4

CONTROL PANEL See Figures 3-2 & 3-3

CENTRAL PROCESSING UNIT (CPU) PCB See Figures 3-8 & 3-9 VIDEO PCB See Figures 3-8 & 3-10

COIN DOOR See Figure 3-7 SERVICE SWITCH

REGULATOR/ AUDIO II PCB See Figures 3-8 & 3-11 UTILITY PANEL See Figure 1-2

POWER SUPPLY See Figure 3-12

WARNING SHOCK HAZARD Connect this game only to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electric shock if this game is not properly grounded! POWER ON/OFF SWITCH See Figure 1-2

Figure 1-1 Game Overview

1-2

Page 11

Kangaroo™

A. New Features

The Kangaroo™ game has two new features. Even if you are familiar with ATARI® games, you should

note these important differences: @ Joystick Control. This new eight-position control is made of steel and molded plastic. It has few parts, which make servicing easier. The leaf switches snap in and out for easy replacement. The rubber bellows is designed for a quick return to center. @ Service Switch. There is a service switch located on the CPU PCB which allows you to enter credits without tripping the coin counter. New features and all other major parts in the game are illustrated in Figure 1-1. Throughout this manual, wherever one of these new features is mentioned, you will see this symbol:

B. Game Inspection

Please inspect your game carefully to insure that it was delivered to you in good condition.

NOTE Do not plug the game in yet!
  • Examine the exterior of the game cabinet for dents, chips, or broken parts.
  • Remove the screws that were used as extra security to seal the rear access panel. Unlock and open this panel and the coin door; inspect the interior of the game as follows: @ Check that all plug-in connectors (on the game harness) are firmly seated. Replug any connectors found unplugged. Don’t force connectors together. The connectors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB and will void your warranty. @ Check that all plug-in integrated circuits on the PCBs are firmly seated in their sockets. @ Remove the tie-wrap that holds the coiled power cord on the inside cabinet wall. Check the power cord for any cuts or dents in the insulation. Place the square black plastic strain-relief plate in the wood slot at the bottom of the rear panel opening. Set-Up Procedures
WARNING To avoid electrical shock, do not touch internal parts of the display with your hands or with metal objects held in your hands!

@ Note the game’s serial number. It is printed on a label on the back of the cabinet. Verify that the same serial number is also on the Kangaroo game PCBs, Regulator/Audio II PCB, power supply and video display. A drawing of the serial-numbered components is on the inside front cover of this manual. Please mention this number whenever you cail your distributor for service. @ Check major subassemblies, such as the power supply, control panel and video display, for secure mounting.

C. Game Installation

  • Installation Requirements

Power 150W Temperature 0 to 38°C (32 to 100°F) Humidity Not over 95% relative Upright Cabinet 64 x 79 cm (25% x 31 in.) 174 om (68% in.) Ireland-Built Cabinet Space Required 64 x 79 cm (25% x 31 in.) Game Height 174 cm (68% in.) Space Required Game Height

  • Voltage Selection The power supply used in this game operates on the line voltage of almost any country in the world. The power supply comes with either one, two, or three different voltage selection plugs. Plug voltages and wire colors are 100 VAC (violet wire color), 120 VAC (yellow wire color), 220 VAC (blue wire color), and 240 VAC (brown wire color).

Before plugging in your game, check your line voltage. Then check the wire color on the voltage selection plug that is plugged into your power supply. Make sure the voltage selection plug is correct for your location’s line voltage (see Figure 3-12).

1-3

Page 12

Set-Up Procedures

D. Switch Locations

  • On/Off Switch The on/off switch is located on the back of the cabinet, lower left side (see Figure 1-2).
  • Utility Panel Switches The utility panel includes the volume control, selftest, coin switch, and coin counter(s). The coin switch is used to credit the game and it activates the left coin counter. These switches are located inside the upper coin door (see Figure 1-2). Kangaroo™
  • Service Switch The service switch is located on the CPU PCB. It is used to credit the game without activating the coin counter. It can also start self-test if it is pressed while powering on the game.
  • Option Switches Option switches are located on the CPU PCB in the upper right corner, to the right of IC42.

UTILITY PANEL:

COIN COUNTER

SELF-TEST

VOLUME CONTROL (TO increase, turn clockwise) GAME OPTION SWITCHES

POWER ON/OFF SWITCH

Figure 1-2 Game Switch Locations

1-4

Page 13

Kangaroo™ Set-Up Procedures

E. Option Switch Settings

Table 1-1 details game option switch settings. Op- To verify option switch settings, power the game tions are preset at the factory and shown by the < off and then on again. Set the self-test switch to on symbols. However, you may change the settings to and verify the settings on the self-test screen. Then suit your individual needs. set the self-test switch to off.

Table 1-1 Option Switch Settings The table below contains the switch settings for options re- The coin mechanism(s) is a device on the inside of the coin door lating to number of Kangaroo lives, game difficulty, bonus and that inspects the coin to determine if the correct coin has been inprice options. The switches are on the CPU PCB to the right of serted. After this inspection, the mechanism either accepts the C42 and are accessible when the PCB is mounted in place, coin or rejects it.

Settings of 8-Toggle Switch on Kangaroo CPU PCB 2 3 4

15678Option

Off 3 Kangaroo Lives < On 5 Kangaroo Lives Off Easy game difficulty < On Hard game difficulty

OffOffNo Bonus Kangaroos
OnOffBonus Kangaroo at 10,000
OffOnBonus Kangaroo at 10,000, 30,000 and every 30,000 thereafter
OnOnBonus Kangaroo at 20,000, 40,000 and every 40,000 thereafter

Left Coin Mechanism Right Coin Mechanism Games with one coin counter Games with two coin counters

OffOffOffOff1 coin for 1 credit1 coin for 1 credit <
OnOffOffOff2 coins for 1 credit2 coins for 1 credit
OffOnOffOff2 coins for 1 credit1 coin for 3 credits
OnOnOffOff1 coin for 1 credit1 coin for 2 credits
OffOffOnOff1 coin for 1 credit1 coin for 3 credits
OnOffOnOff1 coin for 7 credit1 coin for 4 credits
OffOnOn = Off1 coin for 1 credit1 coin for 5 credits
OnOnOnOff1 coin for 1 credit1 coin for 6 credits
OffOffOffOn1 coin for 2 credits1 coin for 2 credits
OnOff= OffOn1 coin for 2 credits1 coin for 4 credits
OffOnOffOn1 coin for 2 credits1 coin for 5 credits
OnOnOffOn1 coin for 2 credits1 coin for 10 credits
Off= OffOnOn1 coin for 2 credits1 coin for 11 credits
OnOffOnOn1 coin for 2 credits1 coin for 12 credits
OffOnOnOn1 coin for 2 credits1. coin for 6 credits
OnOnOnOnFree playFree play

“4 Manufacturer's recommended settings

NOTE

When bonus life options are changed, make sure the proper sticker behind the shield is displayed.

Page 14

Set-Up Procedures

F. Self-Test Procedure

This game will test itself and provide data to show that the game’s circuitry and controls are operating properly. The data is provided on the video display and speaker. No additional equipment is necessary.

We suggest you perform the self-test procedure when you first set up the game, any time you collect money from the game, when you change game options, or when you suspect game failure. Kangaroo™

Refer to Figure 1-2 for the location of the self-test switch and option switches. To perform the self-test, set the self-test switch to on or simultaneously power the game on and press the service switch. To end the self-test, set the self-test switch to off.

The complete self-test procedure is explained in Chapter 2, Self-Test Procedure. \f a part of the test described in Figure 1-3 fails, refer to Chapter 2.

Figure 1-3 Self-Test Procedure Instruction Test Passes

  • Set the self-test switch to on (see Figure 1-2).
  • Observe the seven colored squares.
  • Activate all switches: contro! panel, coin and service.
  • Simultaneously press Player 1 and Player 2 start switches. The screen shows the self-test display. The ROMs and RAMs. are tested. If the screen is different from the self-test display, refer to Chapter 2, Self-Test Procedure.

Colors are blue, greer, light blue, red, violet, yellow and white. If colors are not as described, refer to the raster-scan video display manual.

The 0 changes to 7 as the switch is activated. If test fails, refer to Chapter 3, The Control Panel. Push the joystick diagonally up and to the left. For proper game operation, both the top and left switches must close at the same time, and the top and left 0s should each become 1. Push the joystick diagonally up and to the right, repeating the same procedure. Both the top and right switches should close, changing the corresponding Os to 7s on the screen. If the test fails, refer to Chapter 3, 8-Position Joystick Assembly.

Game sounds are produced and increment automatically from SOUND 1 through SOUND J. If test fails, refer to Chapter 2, Self-Test Procedure.

Game sounds: SOUND 1 SOUND 2 SOUND 3 SOUND 4 SOUND 5 SOUND 6 SOUND 7 SOUND 8 SOUND 9 SOUND A SOUND B SOUND C SOUND D SOUND E Game melody Kangaroo jumping Kangaroo punching Kangaroc falling Kangaroo dying Apple falling Kangaroo punching apple or gorilla Bonus Kangaroo awarded Begin new level Monkey dying Kangaroo getting fruit End of level Bell ringing Monkey column decreasing by one monkey SOUND F Gorilla taking Kangaroo’s gioves SOUND G_ Kangaroo crouching SOUND H_ Apples falling from broken branch SOUND! Kangaroo climbing ladder SOUND J Kangaroo hopping

1-6

Page 15

Kangaroo™ Set-Up Procedures

COCKTAIL ONLY PLAYER-2 JOYSTICK CONTROL LT. BLUE

COCKTAIL ONLY RED PLAYER-2 PUNCH

VIOLET

GREEN 0 0 YELLOW

BLUE

WHITE

COLOR =

ADJUSTMENT —__—_—_____ CHART

DIP123456783A3BdASHcontion

Goo100co0 1 12 SETTIN ~. —T =,

SERVICE SWITCH ————> =Q:i

<< FIGHT COIN MECH

' ———— 1 + PLAYER START 0 4 LEFT COIN MECH

2PLAYER sTaRT————— = 0L£+#O0\0

ra

SOUNDS

NO. OF LIVES GAME PRICING! GAME DIFFICUTLY CREDITS

JOYSTICK CONTROL BONUS LIVES PUNCH OPTION SWITCHES -—| oa

  • These represent harness connections on the CPU PCB. 1 means the pin is shorted to ground in the harness. 0 means there is no connection in the harness. Screen Pin on CPU Shows Harness Connector 3A c 3B 3 4A D 8A J
NOTE: 8A is a zero if you enter sef-test mode by pressing the service switch on the CPU PCB.

Figure 1-3 Self-Test Procedure, continued Self-Test Display

Page 16

Set-Up Procedures

G. Game Play

The Kangaroo™ game is a one- or two-player game with a color raster-scan video display. Game action takes place in the branches of a tree. The player controls a mother Kangaroo who must hop and leap from the bottom of the screen to the top to rescue her kidnapped baby. In her effort to get to her baby, the Kangaroo must punch out monkeys and avoid fruit that is thrown or dropped by the monkeys.

Kangaroo has five possible modes of operation: attract, ready-to-play, play, high-score and self-test. Self-test is a special mode for checking the game switches and computer functions. You may enter self-test at any time (all credits will be cancelled and the high score table will be erased).

  • Attract Mode

The attract mode begins when power is applied to the game, after a play or high-score mode, or after self-test. This mode is continuous and stops only when a credit is entered, or when in self-test. In the attract mode, the screen displays one of three possible pictures.

The first picture shows ways to score points during game play. A mother Kangaroo hops across a top branch of the tree. She /eaps to touch hanging fruit with her head and to ring a bell. When she touches the fruit, it disappears and a point value appears in its place. When she rings the bell, a new fruit appears where the old fruit was hanging. A monkey pursues the mother Kangaroo and she punches him. The monkey disappears, and a point value appears in his place. Meanwhile, the baby Kangaroo climbs down a ladder and goes to the mother Kangaroo. When they touch, the word MOM appears on the screen above the baby.

In addition to the game play simulation, PLAYER-1, LEVEL=1, PLAYER-2 and KANGAROO appear at the top of the screen. The high score appears in the center of the screen. Credits and © 1982 ATARI, INC. appear at the bottom of the screen. Kangaroo™

The second picture shows the high-score table. The top ten scores and their matching initials appear on the screen. The words KANGAROO and IN- SERT COINS also appear.

The third picture simulates game play. Mother Kangaroo enters at the bottom of the screen. She hops across a tree branch and avoids fruit thrown or dropped by monkeys and punches out monkeys. She leaps to touch fruit with her head. She climbs a ladder to get to the next branch of the tree. In this way she hops, leaps and climbs to the top of the tree to rescue her baby. She rescues her baby, or in another simulated game, is destroyed by an apple thrown by a monkey.

In addition to game play, PLAYER-7, LEVEL =1, PLAYER-2, number of Kangaroo lives and bonus information appear at the top of the screen. The attract mode ends when coins are entered and accepted for game play.

  • Ready-To-Play Mode

During this mode the game level and score(s) for one or both players appear at the top of the screen. The words PUSH ONLY 1 PLAYER BUTTON appear when 1 credit is inserted. The words PUSH 1 OR 2 PLAYERS BUTTON appear when 2 or more credits are inserted. LET'S CHALLENGE also appears in the center of the screen. Credits appear in the bottom left corner of the screen. This mode ends when a player pushes the start button.

A picture appears briefly on the screen, showing three mother Kangaroos on three branches of the tree. The mother Kangaroo on the top branch falls through a gap to the bottom of the screen. The other Kangaroos join their babies, and the words MOM appear above their heads.

Page 17

Kangaroo™

  • Play Mode

In the Play Mode, the player controls the mother Kangaroo with an 8-position joystick. Thus, the player causes the Kangaroo to hop to the right or left, or to leap up to touch fruit, or to jump over apples thrown at her by monkeys. She may climb up |adders, or SUPER-LEAP diagonally to the left or right to climb up log-type stairs. The Kangaroo may also duck to avoid thrown apples, or hop down diagonally to the left or right to get down the log-type stairs.

Another player control is the PUNCH button. When pushed, it causes the Kangaroo to punch with her boxing glove. She may punch monkeys for 200 to 400 points. She may also punch fruit that is thrown or dropped by monkeys for 100 to 200 points. In addition, Big Ape may appear and try to take the Kangaroo’s gloves. Punching Big Ape is worth 800 points.

Game play progresses by levels. Each level has four rounds. Game play begins at Level 1. Bonus points appear at the top left of the screen. There are 2,000 bonus points at the beginning of each round, and the points decrease by 100 every five seconds. Remaining bonus points are awarded at the end of the round.

In Level 1, Round 1, mother Kangaroo is at the bottom of the screen on the branch of a tree. She must get to the top of the screen to rescue her kidnapped baby by hopping across tree branches and climbing up ladders to get to the next branch. The Kangaroo must avoid apples thrown or apple cores dropped by monkeys. She must punch out the monkeys that are in her way. For extra points, she touches strawberries by leaping to touch them with her head or by hopping on them. (If the Kangaroo rings the bell, new fruit appears in place of the strawberries.) ‘Set-Up Procedures

The Kangaroo may also punch thrown or falling fruit for extra points. But if she is hit by fruit or touched by a monkey, she dies and a halo appears over her head. If she hops, leaps and climbs to the top of the tree and gets to her baby, this round ends.

In Round 2 there are log stairs instead of ladders for the mother Kangaroo to climb. To get up the stairs, she must leap diagonally (GUPER-LEAP). The Kangaroo must be careful not to fall through any gaps in the stairs or on the branches, or she will die. Also, Big Ape may appear in this round. He takes the Kangaroo’s glove away from her by coming close to her and extending his arm. For about 10 seconds, the Kangaroo has to defend herself with a white flag. Then her glove reappears.

In Round 3 the baby Kangaroo is in a cage at the top of a column of monkeys. Mother Kangaroo may either punch out the monkeys one by one (for 400 points each), or climb up ladders to a branch of the tree where she can hop into the cage. The column increases by one monkey every 10 seconds. In addition, monkeys climb up a vine to get to a stack of 11 apples on a branch at the top of the screen. If the mother Kangaroo takes too long to get to her baby and a monkey gets to the apples, the branch breaks, and all the apples fall at one time.

In Round 4 there are ladders with missing rungs, stairs to climb, and gaps in the branches, making the rescue more difficult. If a player completes this round, Level 2, Round 1 begins. The player may punch the thrown fruit to score points. Play becomes more difficult as game play progresses. The game ends when all the Kangaroo’s lives are used up.

1-9

Page 18

Set-Up Procedures

  • High-Score Mode This mode begins when a player has one of the top ten scores. Letters of the alphabet are at the top of the screen, and the high score table is below the letters. A player enters his initials by using the joystick to guide a highlighted square to his initials. By pressing the PUNCH button, the initial is transferred onto a line between the alphabet and the high-score table. After the initials are entered, they are transferred into the table. To reset the high-score table, power the game off and then on, or enter and end the self-test mode.
  • Hints for Game Play @ Ring the bell for extra points. New fruit with higher point value will appear in place of the old fruit. @ Avoid walking into a monkey. Punch monkeys for 200-400 points each. @ Do not let Big Ape take mother Kangaroo’s glove (it reappears after 10 seconds). @ Mother Kangaroo must duck, leap or punch to avoid being killed by thrown or dropped fruit.

1-10 Kangaroo™

Table 1-2. Kangaroo Scoring

Kangaroo Punching Points Thrown Apples 100 Monkey Apple Cores Monkey from Column Big Ape

Kangaroo Jumping to Touch Fruit Strawberry Tomato Cherries Pineapple Completing Round

  • Decreases by 100 every 5 seconds
Page 19

Troubleshooting

This game tests itself when the self-test switch is set to the on position. If there is a failure, the game produces audiovisual aids to help you isolate the failing portion of the game. The self-test procedure included in Chapter 1 will help you decide if the game is or isn’t working properly. The expanded self-test procedures in this chapter are included to help the qualified electronic technician determine why the game isn’t working properly.

Page 20

A. Comments on Troubleshooting

When troubleshooting, first determine the symptom(s) of the failure. After determining the symptom, look over the wiring diagram and determine what assemblies could cause the failure. Could it be caused by the power supply, Regulator/Audio I! PCB, or the video display?

The next step is to check all harness wires and connectors to the suspected failing assembly. If you find no harness or connector problem, substitute an assembly known to be good for the suspected failing assembly. If the game functions properly, you have successfully isolated the failure. If it doesn’t, repeat the procedure with another assembly.

When you have isolated the failing assembly, you must troubleshoot that assembly and make the necessary repairs. If the display is failing, we suggest that a qualified video display technician handle the troubleshooting and repair. If the power supply or Regulator/Audio || PCB is failing, troubleshooting and repair are relatively simple, as these assemblies are not too complicated. If a game PCB is failing, troubleshooting and repair will greatly depend on your understanding of the operation of the PCB.

To effectively troubleshoot problems of a game PCB, it is necessary for you, the technician, to become familiar with the PCB’s hardware. The diagrams in the schematic package (included with the game) show the functions of the circuitry. Again, while troubleshooting the PCB, first determine the symptom of the failure, then locate the suspected area on the schematic diagram. Kangaroo™

B. Self-Test Procedure

To enter Self-Test, set the self-test switch to the on position. The screen displays the picture below. See Chapter 1, Section F, Self-Test Procedure for a complete description of this picture.

NOTE This procedure does not test the coin door lockout coils. If the Self-Test passes, but the lockout coils do not energize when power is applied to the game, suspect the lockout coil wiring, coin door harness, game PCB harness, or transistor TRS (for the /reland-Built cabinet check TR3 and TR4) and related circuitry of the CPU PCB.

OLP 12345678 3A 38 4A 54 000190000 1 O 4 2 yong

Figure 2-i Self-Test Screen 1 Test Passes

Page 21

Kangaroo™

0 0+0 ROR eons ROR ROM Ue

DIP 12345678 3A 3B dA 8A ooo1ooco0 2 OO tk B

L

Zz ty

tt}

Figure 2-2. Self-Test Screen 1 Test Fails

SCREEN 1: ROM FAILURE is indicated on the screen by the words ERROR ROM- and a number (for a ROM failure on the CPU PCB), or the words ERROR ROM V- and a number (for a failure on the Video PCB).

Note the indication of failure in Figure 2-2. The following lists the ROM chips and their locations.

Bad ROM Chip Location B Screen Display te ROM-0* 107 ROM-1 Ice ROM-2 1c9 ROM-3 1010 ROM-4 IC16 ROM-5* IC17 ROM-8* 1C24 ROM-12* 1028 Video PCB ROM V-0 IC76 ROM Y-1 1052 ROM V-2 1077 ROM V-3 IC53

*Does not display on the screen if defective.

RAM FAILURE is indicated by a blank screen or by garbage displayed on the screen for a defective RAM at IC5 or IC6 on the CPU PCB. Make sure that ROM-0 and ROM-5 are good on the CPU PCB. In addition, inspect the dynamic RAM on the Video PCB Troubleshooting

at locations IC55-62, 66-73, 79-86 or 93-100. Troubleshoot using the game schematics and the CAT Box (using a Z80 interface) or a bus controller to locate the failing RAM.

SWITCH FAILURE is indicated by the proper 0 or 7 not changing on the screen when the switch is activated. Troubleshoot using the information in Chapter 3, Section B and game schematics.

SOUND FAILURE is indicated by no sound. Check the volume control levels on the utility panel and on the CPU PCB at VR2. Troubleshoot the following sound circuitry on the CPU PCB: G.I. sound chip at 1C50, ROM 8 at 1C24, Z80 Microprocessor at IC34, RAMs at IC32 or 33, or audio amplifier at 1C61.

To go to screen 2, push the 1-player start and either PUNCH switch at the same time.

SCREEN 2:

A white crosshatch pattern with white dots centered in each square appears on the screen (see Figure 2-3). The center part of each side of the red rectangle should be %4-inch behind the bezel, out of view. Use this pattern for convergence and white balance (see the raster-scan video display manual).

Figure 2-3 Self-Test Screen 2

Page 22

Troubleshooting Kangaroo

C. Troubleshooting With the CAT Box and Z80 Interface Adapter

  • Preliminary Set-Up Procedure a.

b. Disconnect the electrical power from the game. Disconnect the wiring harness from the game PCB. Remove the game PCB from the game cabinet following the procedure given in Chapter

  • Remove Z80 microprocessor IC15 from the game PCB. Connect the CAT Box flat cable connector to the 50-pin connector of the CAT Box/Z80 Interface Adapter. Connect one end of the 40-pin flat cable supplied with the Interface Adapter to the 40-pin connector of the Interface Adapter. Connect the other end of the 40-pin flat cable to the socket of Z80 microprocessor 1C15 on the game PCB. Connect the DATA PROBE ground of the CAT Box to pin 8 of IC1 on the game PCB. Apply power to both the CAT Box and the game. Set the following CAT Box switches as indicated: R/W MODE: (OFF) R/W: WRITE BYTES: 1024 DBUS SOURCE: ADDR TESTER MODE: R/W TESTER SELF-TEST: OFF Press the TESTER RESET button on the CAT Box.
  • Working RAM Check Check Working RAM of the game PCB as follows: a. b.

2-4 Perform the Preliminary Set-Up Procedure. Enter address E000 on the CAT Box keyboard. Check that E000 is shown on the AD- DRESS/SIGNATURE display of the CAT Box. Set R/W MODE to PULSE and then back to (OFF). Set RW to READ. Set R/W MODE to PULSE. Check the COMPARE ERROR light-emitting diode (LED) on the CAT Box. If this LED is off, the game Working RAM is okay. If this LED is turned on, first check that all interconnections between the CAT Box, Interface Adapter, and game PCB are correctly and securely made. Then repeat parts a through f of this procedure. If the COMPARE ERROR LED lights up again, check the game Working RAM for failure.

  • Display RAM Check

Check the Display RAM of the game PCB as follows: a. b. C.

© Perform the Preliminary Set-Up Procedure. Perform the Working RAM Check. Set the following CAT Box switches as indicated: R/W MODE: (OFF) DBUS SOURCE: DATA BYTES: 1 Write FF to address E808. (To write data from the CAT Box to the game memory, first set R/W to WRITE. Then, enter the hexadecimal address with the keyboard on the CAT Box. Check that the address shown in the ADDRESS/SIGNATURE display of the CAT Box is correct. Then press the DATA SET button and enter the hexadecimal data with the keyboard on the CAT Box. Check that the data shown in the DATA display is correct. Then set R/W MODE to PULSE and back to (OFF) to send the data to the game memory address shown in the AD- DRESS/SIGNATURE display.) Press the ADDRESS INCR button to advance the ADDRESS/SIGNATURE display to E809. Write OC to address E809. Press the ADDRESS INCR button to advance the ADDRESS/SIGNATURE display to E80A. Write FF to address E80A. Set BYTES to 1024. Write 00 to addresses 8000, 8400, 8800, 8C00, 9000, 9400, 9800, 9C00, A000, A400, A800, ACOO, B000, B400, B800, and BCOO. Check that a section of the game display is erased when the R/W MODE switch is used to write data to each of the above addresses. The erasing begins at the bottom of the display and proceeds upward by sections. Sei BYTES io i. Write 03 to game address E808.

Page 23

Kangaroo

pors3 Enter the game memory address in Table 2-1. . Press DATA SET. Enter the data from Table 2-1. Set R/W MODE to PULSE and back to (OFF). Repeat parts | through o for each address listed in Table 2-1. Check that a Mother Kangaroo has been drawn at the center of the game display screen. If the Mother Kangaroo is not accurately displayed, repeat parts g through p. If the Mother Kangaroo still is not accurately displayed, check the game display circuitry for failure.

Table 2-1 Display RAM ADDRESS DATA

E800 00 E801 co £802 80 E803 20 E804 1B E805 06"

*This data must be written last.

  • Sound Microprocessor Check

Check the Sound Microprocessor as follows:

a

b.

c.

ea-ooa Perform the Preliminary Set-Up Procedure. Perform the Working RAM Check. Set the following CAT Box switches as indicated: BYTES: 1 RW: WRITE RIW MODE: (OFF) Enter game memory address ECO0 with the CAT Box keyboard. Press DATA SET.

Enter the data from Table 2-2. Set R/W MODE to PULSE and back to (OFF). Check for the response indicated in Table 2-2. If the correct response does not occur, check the game sound circuitry for failure. Repeat parts d through g for each data listed in Table 2-2. Troubleshooting

Table 2-2 Sound Microprocessor

ADDRESS

ECOO ECOO

Ecoo ECOO ECoo

ECOO ECOoO ECOO ECOO ECOO

ECOO

ECOO ECOO ECOO EC0O ECoo ECOO ECOoO

Ecoo

ECoo ECo0

ECoo

ECOO

ECOO

ECoO ECoo DATA

OA

0B oc oD OE

OF

an RESULTING SOUND

Stops all sounds. Initializes the Sound Microprocessor. No sound is produced. Game melody. Stops game melody. Initializes the Sound Microprocessor. Kangaroo jumping. Kangaroo punching. Kangaroo falling. Monkey dying. Kangaroo punching apple or gorilla. Bonus Kangaroo awarded. Begin new level. Apple falling. Kangaroo dying. Kangaroo getting fruit. End of level. Bell ringing. Monkey column decreasing by one monkey. Gorilia taking Kangaroo’s gloves. Kangaroo crouching. Apples falling from broken branch. Kangaroo climbing ladder. Stops Kangaroo climbing ladder sound. Initializes Sound Microprocessor. Kangaroo hopping. Stops Kangaroo hopping sound.

Page 24

Troubleshooting

Table 2-3 Display Addressing Memory Map Kangaroo

ADDRESSDATABITFUNCTIONADDRESSDATABITFUNCTION

STATE STATE £808 DBO = 1 _ Enables writing to play- £809 DB2 = 0 _ Disables motion display.

RAM Ramana tranDB3 = 1Enables playfield display.
DBO = 0Disables writing to play-DBS = 0on bles playfield dis-

field red RAM and bright ° .

RAM.DB4 = 1Flips the motion display.
DB1=1Enables writing to play-DB5 = 1 _ Flips the playfield dis-

field blue RAM and play- Play.

field green RAM. E80A DBO = 1 Disables motion blue

DB1=0Disables writing to play-bright bit.
field blue RAM and play-DBO = 0Enables motion blue

field green RAM. bright bit.

DB2 = 1Enables writing to Mo-DB1 = 1Disables motion green

tion red RAM and bright bright bit. RAM. DB1 = 0 _ Enables motion green

DB2 = 0Disables writing to mo-bright bit.

Ea RAM and bright DB2 = 1 Disables motion red tion blue RAM and mo- DB2 = 0 Enables motion red DB3 = 0 Disables writing to mo- DB3 = 1 ince Nile ile blue

DB3=1& oIiting tener

= nables writing to mo- _ .

tion green RAM. ng a

tion blue RAM and mo- rig ;

tion green RAM.DB3 = 0Enables playfield blue
E809DBO = 1Disables priority to mo-bright bit.
tion RAM.0B4 = 1Disables playfield green
DBO = 0Enables priority to mo-bright bit.
tion RAM.DB4 = 0Enables playfield green
DB1 = 1Disables priority to play-bright bit.
field RAM.DB5 = 1Disabies playfield red
DB1 = 0Enables priority to play-bright bit.
field RAM.DB5 = 0Enables playfield red
DB2 = 1Enables motion display.bright bit.
Page 25

Kangaroo Troubleshooting

D. Glossary of Schematic Signal Descriptions

CPU PCB Signals NMI

Wait

iNT

®

cs2

ADD

RD(H)

WR)

WR(H)

xyvD

XH)

VPOS

HPOS

BSEL

VILEN PRI

INO

INa

ourTo

ourTi

OUT2 Non-Maskable Interrupt

Wait

Interrupt Request (every 16 ms)

CPU Clock (2.5MHz)

Address Select (E8XX-EBXX)

Start Address of Data in Picture ROM for DMA Low Byte

High Byte

Low Byte Start Address in Bit Map RAM (Where Picture is High Byte Written) During DMA

Low Byte Picture Size for DMA and DMA Start High Byte

Vertical Start Address in Bit Map

Horizontal Start Address in Bit Map

Dynamic RAM Bank Select Latch Set

A and B Bit Map Control Latch Set

Input Address Select ECO0 (See Memory Map)

Input Address Select ED00 (See Memory Map)

Input Address Select EE00 (See Memory Map)

Input Address Select EFOO (See Memory Map)

Input Address Select E400 (See Memory Map)

Output Address Select ECOO (See Memory Map)

Output Address Select EDOO (See Memory Map)

Output Address Select EE0O (Not Used) OUT3

HFEN

SDO-SD7

BDIR

BC1

ISO-IS3

OS0-0S3 Output Address Select EFOO (See Memory Map)

Set Color-Shading Latch

Sound Microprocessor Data Bus

GI AY-3-8910 Sound Chip Input/Output Select

GI AY-3-8910 Sound Chip Addres/Data Latch Select

MB8841 Custom Microcomputer Input Data Bus

MB8841 Custom Microcomputer Output Data Bus

Video PCB Signals KO

Kt

kK2

KIst

kos

XG

LDSFT

WE

EXCT

EXCT

SEL Wil (A)

SEL Ill (B)

csco00

BSELO

BSEL 2

Ave’ Dynamic RAM Timing Signals (See Timing Diagram in Kangaroo Schematic Package)

DMA in Progress (Active High)

DMA in Progress (Active Low)

Flip Video Address (Dynamic RAM A)

Flip Video Address (Dynamic RAM B)

Character ROM Address Select

Bank Select Dynamic RAM A

Bank Select Dynamic RAM B

Horizontal Blanking (Active Low)

Page 26

Troubleshooting Kangaroo

BRAS1

  • NOTE: Oynami

RAM B refers

Horizontal Syne

Vertical Sync

Dynamic RAM A* Color Shading/Red RAS

Dynamic RAM A Blue/Green RAS.

Dynamic RAM A Color Shading/fRed CAS

Dynamic RAM A Blue/Green CAS.

Dynamic RAM A Color Shading/Red Write Enable

Dynamic RAM A Blue/Green Write Enable

Dynamic RAM B Color Shading/Red RAS

Dynamic RAM B Blue/Green RAS

iit RAM A refers to Playfield Bit Map; Dynamic to Motion Object Bit Map BCASO

BCAS1

BWEO

BWE1

AVAX0-13

AVBX0-13

ABPO-11

ABX0-13

DPZO0-3

DPRO-3

DPG0-3

DPBO-3

DXZ0-3 Dynamic RAM B Color Shading/Red CAS

Dynamic RAM B Blue/Green CAS

Dynamic RAM B Color Shading/Red Write Enable

Dynamic RAM B Blue/Green Write Enable

Dynamic RAM A Video Address Dynamic RAM B Video Address

Picture ROM Address

Dynamic RAM Address from CPU and for DMA

DMA Color Shading Data from Picture ROM

DMA Red Data from Picture ROM

DMA Green Data from Picture ROM

DMA Blue Data from Picture ROM

Dynamic RAM Data Bus—Color Shading Data

Page 27

Kangaroo

DXRO-3

DXGO-3

DXB0-3

XXA06

XXBO0-6

PRIA

PRIB

ENA

AGHF

ABHF

BRHF

BGHF Dynamic RAM Data Bus—Red Data

Dynamic RAM Data Bus—Green Data

Dynamic RAM Data Bus—Blue Data

Dynamic RAM A Address Bus

Dynamic RAM B Address Bus

Playfield Priority (Active Low)

Motion Object Priority (Active Low)

Playfield Video Output Enable (Active High)

Motion Object Video Output Enable (Active High)

Playfield Red Color Shading (Active Low)

Playfield Green Color Shading (Active Low)

Playfield Blue Color Shading (Active Low)

Motion Object Red Color Shading (Active Low)

Motion Object Green Color Shading (Active Low) AVR

AVG

AVB

BR

BG

BB

BVR

BVG

BVB Troubleshooting

Motion Object Blue Color Shading (Active Low)

Playfield Red Data

Playfield Green Data

Playfield Blue Data

Playfield Red Data AND Playfield Red Color Shading AND Playfield Priority

Playfield Green Data AND Playfield Green Color Shading AND Playfield Priority

Playfield Blue Data AND Playfield Blue Color Shading AND Playfield Priority

Motion Object Red Data

Motion Object Green Data

Motion Object Biue Data

Motion Object Red Data AND Motion Object Red Color Shading AND Motion Object Priority

Motion Object Green Data AND Motion Object Green Color Shading AND Motion Object Priority

Motion Object Blue Data AND Motion Object Blue Color Shading AND Motion Object Priority

Page 28

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 29

Maintenance, Repair and Parts

This chapter details maintenance and repair information, and provides information for you to order parts for your Kangaroo game. Please note that common hardware has been deleted from most of the parts lists. This includes screws, nuts, washers, bolts, etc.

The parts lists are arranged in alphanumeric order. For example, all “A-” prefix numbers come first. Following these are numbers in sequence evaluated up to the hyphen, namely 00- thru 99-, then 000598thru approximately 190000-.

When ordering parts, please give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.

Atari Customer Service numbers are listed in the front of this manual for your convenience.

Chapter

Page 30

Maintenance, Repair and Parts. Kangaroo™

A. Cabinet-Mounted Assemblies

Schematics, Self-Test Labe! & Manuals— see parts list on following page

A038411-01 (Cabinet Assy.) 03733201 (Grille) Fluor. Light & Speaker— 178034-024 036498-01 See Figure 3-5 (FMolding) (Upper Retainer) (Upp ) nen

(Lock) 038420-01 (Attract. Glass) 03741902

  • (Access Panel)

003053-01 (Lower Retainer)

Video Display— 036495-01 See Figure 3-6 (Grille) CPU PCB Assy.— a S See Figures 3-8 & 3-9 038419-01 78-6900402 (Shield) (Tape) Video PCB Assy.— See Figures 3-8 & 3-10 178013-001 (Latch) Control Panel Assy.— See Figures 3-2 & 3-3

Reg./Audio II PCB Assy.— See Figures 38 & 3-17

‘A038004-01 Coin Door Assy.— (Util. Sw. Harn.) See Figure 3-7

‘A038453-01 (Power Harn. Assy.)

Power Supply Assy.— See Figure 3-12 A037491-01 (Coin Box)

038003-01 (Util. Panel)

A002465.01 (Coin Counter)

69-001 (Self-Test Sw.) 62.041 é (Coin Sw.) ‘A037470-01 (OniOtt Sw.) 009992.01 (OniO#t Sw. Cover) 178048-001 (Caster)

~ 78-3201 19-9032 (Glide) (Vol. Control)

178070-001 (Vol. Control Knob)

Figure 3-1 Cabinet-iviounted Assembiies Upright Cabinet A038410-01 E

3-2 ‘A038578-01 (Main Harn. Assy.)

\ A037453-03, A037454-03 & A037455-03 (Power Cord)

Page 31

Kangaroo™ Maintenance, Repair and Parts

Figure 3-1 Cabinet-Mounted Assemblies, continued Upright Cabinet Parts List

Part No. Description A002465-01 6V Coin Counter A037453-03 Strain-Relief Power Cord (U.S.) A037454-03 Strain-Relief Power Cord (Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece, Indonesia, Italy, Netherlands, Norway, Spain, Sweden, and Uruguay) A037455-03 Strain-Relief Power Cord (Australia and New Zealand) A037470-01 Power On/Off Switch and Mounting Plate Assembly A037491-01 Coin Box A038004-01 Utility-Switch Panel Harness Assembly

A038411-01Cabinet Assembly(includes legs and PCB retainers, but not the rear access panel)

A038578-01 Main Harness Assembly A038453-01 Power Harness Assembly The following four items are the technical information supplements to this game: SP-204 Kangaroo™ Schematic Package $T-204-01 Kangaroo Label with Self-Test Procedure and Option Switch Settings M-160 Service Manual for 19-Inch Electrohome Color Raster-Scan Display Substitute TM-201 when using part no. 92-055, Wells-Gardner 19-Inch Display Substitute TM-205 when using part no. 139003-1005 or -1205, Sanyo 19-Inch Display Substitute TM-197 when using part no. 139003-1004 or -1204, Matsushita 19-Inch Display TM-204 Kangaroo Operation, Maintenance and Service Manual 19-9032 Volume Control 62-041 SPDT Momentary-Contact Pushbutton Utility Coin Switch with Black Cap 69-001 DPOT Self-Test Switch

71-2110Lock Mechanism(for rear access panel)

78-3201 Adjustable Glide 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, %-Inch Wide x ‘Inch Thick (72 in. required) 003053-01 Lower Attraction Glass Retainer 009992-01 On/Off Switch Cover 034536-01 Foam Vibration Damper (for Kangaroo game PCBs) 034536-02 Foam Vibration Damper (for Regu/ator/Audio I! PCB) 036495-01 Speaker Grille 036498-01 Upper Attraction Glass Retainer 036686-01 Card of Game Pricing Labels (not shown in illustration)

03741902Rear Access Panel(does not include lock)
037332-01Ventilation Grilie(located on cabinet top)

038003-01 Utility Switch Panel for Volume Control, Self-Test Switch, Coin Switch and Coin Counter 038419-01 Video Display Shield with Graphics 038420-07 Attraction Glass with Graphics 178013-001 Spring Draw Latch 178034-024 %4-Inch Black Plastic T-Molding 178048-001 2Inch Rigid Caster 178070-001 Volume Control Knob

Page 32

Maintenance, Repair and Parts Kangaroo™

Schematics, Self-Test Label & Manuals— see parts list on following page

038226-01 (Grille) 178034-024 (FMoiding) 03733201 (Grille) Fluor. Light & Speaker— ‘see Figure 0-5

038439-01 (Shield) 037721.02 (Access Panel)

71-2110 (Lock) Video Display— a see Figure 3-6 8-Position Joystick Assy.— See Figure 3-4 78-6900402 (Tape) 178013-001 (Latch) /

Control Panel Assy.— ‘see Figures 3-2 & 3-3

CPU PCB Assy.— oe see Figures 38 & 3-9

(Util. Sw. Harn.) Coin Door Assy.— see Figure 3-7 Video PCB Assy.— see Figures 3-8 & 3-10

Reg/Audio Il PCB Assy.— Figures 3 1 see Figures 3-8 & 3-11 oo 038003-01 (Main Harn. Assy.) (Util. Sw. Brkt.) A002465-01 (Coin Counter) 69-001 (Self-Test Sw.)

62-041 (Coin Sw.) 19-9032 j é Wol. Ctrl) ‘A037491-01 (Coin Box) a 78-3201 (Glide) A038453-01 (Power Harn. Assy.)

A037454-03 (Power Cord)

Power Supply Assy.— a 009992-01 see Figure 3-12 178048-001 (On/Off Sw. Cvr.) (Caster) ‘A037470-01 (On/Otf Sw.)

Figure 31 Cabinet-Mounted Assemblies, continued lreland-Built Cabinet A038430-01 B

Page 33

Kangaroo™ Maintenance, Repair and Parts

Figure 3-1 Cabinet-Mounted Assemblies, continued lreland-Built Cabinet Parts List

Part No. Description A002465-01 Coin Counter A037454-03 Strain-Relief Power Cord (Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece, Indonesia, Italy, Netherlands, Norway, Spain, Sweden, and Uruguay) A037470-01 Power On/Off Switch and Mounting Plate Assembly A037491-01 Coin Box A038004-01 Harness for Volume Control/Self-Test Switch/Coin Counter Assembly

A038431-01Cabinet Assembly(includes glides and PCB retainers, but not the rear access panel)

A038452-01 Main Harness Assembly A038453-01 Power Harness Assembly The following four items are the technical information supplements to this game: SP-204 Kangaroo™ Schematic Package ST-204-01 Kangaroo Label with Self-Test Procedure and Option Switch Settings TM-160 Service Manual for 19-Inch Electrohome Color Raster-Scan Display (Substitute TM-201 when using part no. 92-055, 19-Inch Wells Gardner Display) TM-204 Kangaroo Operation, Maintenance and Service Manual 19-9032 Volume Control 62-041 SPDT Momentary-Contact Pushbutton Utility Coin Switch with Black Cap 69-001 DPDT Self-Test Switch 71-2110 Lock Mechanism (for rear access panel) 78-3201 Adjustable Glide 78-6900402 Vinyl Foam Single-Coated-Adhesive Tape, ¥%-Inch Wide x Inch Thick 009992-01 On/Off Switch Cover 036686-01 Card of Game Pricing Labels (not shown in illustration)

037721-02Rear Access Panel(does not include lock)
037332-01Ventilation Grille(located on cabinet top)

038003-01 Utility Switch Bracket for Volume Control, Self-Test Switch, Coin Switch and Coin Counter 038226-01 Upper Cabinet Grille 038439-01 Video Display Shield with Graphics

038441-01Side Panel Decal(not shown in illustration)

178013-001 Spring Draw Latch 178034-024 %-Inch Black Plastic T-Molding 178048-001 2-Inch Rigid Caster

3-5

Page 34

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 35

Kangaroo™

B. The Control Panel

A— WARNING Prior to removing or repairing any switch on the control panel, unplug the game.

To Open the Control Panel:

  • Open the coin door. Reach up through the opening and release the spring-draw latches, They are on the cabinet side walls at each end of the controi panel.
  • Lift up on the control panel at the top edge, and tilt it toward you. The control panel edge next to the display shield has foam tape applied to it. The tape cushions the shield and prevents liquids from entering the cabinet interior. Make sure this tape is in good condition.

Leaf Switch Repair: @ Adjust the leaf switches for a narrow gap. When a switch button is depressed, the resulting wiping action of the cross-bar contacts provides a self-cleaning feature. Don’t burnish the contacts. To clean them, use electrical contact cleaner. @ To replace a leaf switch, remove the screw with a Phillips-head screwdriver. ®@ To replace the switch button, turn the stamped nut with awrench in a counterclockwise direction, as seen from the inside of the control panel. The ring on the outside of the control panel should not spin, due to its design. Maintenance, Repair and Parts

© Reinstall the switch. Reconnect the harness wires as shown in the Schematic Package, Game Wiring Diagram. Make certain the right colors go to the right tabs on the switch.

Start-Switch Replacement: These switches have a very low failure rate. If a switch should ever be suspect, first test it using the directions that follow.

To Test Switch: @ Remove the wires from the suspected switch. © Attach the leads of an ohmmeter to normally open and common contacts. @ Check contacts (push and release the switch button) for closed and open continuity. @ If the contacts do not operate sharply or always remain closed or open, then replace the switch.

To Replace Switch: @ Remove all wires from the faulty switch. @ Turn the switch counterclockwise while holding the black cone-shaped bushing on the outside of the control panel. @ Install a new switch using the reverse procedure. @ Reconnect the harness wires as shown.

Figure 3-2 SWITCH CONTACTS START 1

BROWN NORMALLY OPEN CONTACT

BLACK COMMON CONTACT

START 2

YELLOW NORMALLY OPEN CONTACT

BLACK ‘COMMON CONTACT

The Control Panel

Page 36

Maintenance, Repair and Parts Kangaroo™

! WARNING !

Players may receive an electric shock if this control panel is not properly grounded! After servicing any parts on the panel, check that the ground wire is firmly attached to the metal tab on the inside of the contro! panel. Only then should you lock up the game.

‘A038435-01 (Cont. Pni.iDecal) 171021-001 038438-04 &Position Joystick Assy.— @ecal) see Figure 3-4 03822401 (Cont. Pai.) * 78-6900402 (Tape) 62-041 75-0108 (Start Sw.) (Flat Washer)

75-040S (Split-Lock Washer)

+o ~ 036895-01 (Beze})

178030-003 (Pushbtn. Assy.) 75-9910NO (Nut) 75-5112B (Carriage Bolt)

03845501 803841501 (Harness) (seen ul i) (Cont. Panel/Decal) 038418-04 (Decal)

038267-01 (Cont. Panel)

Figure 3-3 Control Panel Assembly Upright Cabinet A038414-01_ B lreland-Built Cabinet A038434-01 A

Page 37

Kangaroo™ Maintenance, Repair and Parts

Figure 3-3 Control Panel Assembly, continued Parts List

Part No. Description Upright Cabinet A038415-01 Control Pane! with Decal 75-9415 #10-24 Hex Locknut 038267-01 Control Panel 038418-04 Control Panel Decal Ireland-Built Cabinet A038435-01 Control Panel with Decal 75-010S #10 Flat Washer 75-911S #10-24 Hex Nut 78-6900402 Vinyl Foam Single-Coated-Adhesive Tape, %-Inch Wide x %-Inch Thick (24 in. required) 038224-01 Control Panel 038438-04 Control Panel Decal For Upright and Ireland-Built Cabinets A038455-01 Control Panel Harness Assembly 62-041 SPDT Momentary Pushbutton Start Switch 75-040S #10 Split-Lock Washer 76-5112B #10-24 x 34-Inch Black Carriage Bolt 75-9910NO #%,-11 Steel Stamped Nut 036895-01 Black Molded Switch Bezel 160013-001 Leaf Switch and Button Holder (Leaf switch only is part no. 160012-001) 171021-001 8-Position Joystick Assembly 178030-003 Black Pushbutton Assembly

3-9

Page 38

Maintenance, Repair and Parts

WARNING

Prior to removing or repairing the joystick, unplug the game.

To Repair the Joystick:

  • First remove the entire joystick assembly from the control panel (see Figure 3-3). Now locate the four screws in the plastic joystick frame and remove these screws.
  • Next remove the retaining ring from the bottom of the shaft. The assembly will come apart.
  • To replace the bellows, pry it up and out of the plastic frame. @ Reassemble in reverse order. @ Note that the inner raised ring on the bellows is longer on one side. This side goes on the top of the assembly (toward the control knob).
  • To replace a /eaf switch, you don’t need to disassemble the joystick. @ Using your thumbs, pry apart the plastic flanges on the switch holder. With your index finger, lift the switch up so that it will clear the plastic tab located ‘on the outside end of the switch holder. @ Slide the switch out of its holder. Replace the switch in reverse order. Adjust the switch for a narrow gap.

99-080031 (Bellows)

99-080032 (Gteel Washer)

99-080030 (Spring) SS 99-080037 (Sw Plate) Disassemble in the order indicated. (Circled numbers match the numbered instructions.)

82-AL616 (Screw) Kangaroo™

-S

99-080028 (Shaft)

99-080026

a (Washer)

99-080036 (Top Plate)

99-080029 (Washer)

99-080025 (Switch)

99-080033 (Guard/Actuator)

99-080038 (Sw. Actuator)

73-3003 ae -D--—® (Ring) Figure 3-4 8-Position Joysick Assembly 171021-001

3-10

Page 39

Kangaroo™ Maintenance, Repair and Parts

To Adjust the Joystick:

  • Adjust each switch for narrow gap.
  • Make sure that each teaf switch is firmly seated in its e Se i wa ay from the switch for holder. There is a small gray plastic tab on the outside coer neridnn handle-away fram. te_ switch end of the switch holder. The black plastic part of each © Use a pair of needlenose pliers or a switch adjustleaf switch must be in front of this tab. ment tool to bend each double set of blades in to-
  • Check that all four leaf switches can be activated by ward the center. Make the bend where the double set watching the switch blades as you move the joystick of blades comes out of the black plastic part of the handle up, down, left and right. switch.
  • Test the four diagonal positions. In each diagonal posi- 5. Recheck the switch action. The switches must move intion, two leaf switches should close. Switches should dependently for right, left, up, down and diagonal mocontinue bending slightly after making contact. tion of the joystick.

LEFT: BLUE, BLACK JOYSTICK— TOP REAR VIEW

UP: WHITE/BLACK, BLACK DOWN: VIOLET, BLACK

GREY, BLACK

Figure 3-4 8-Position Joystick Assembly, continued Parts List

Part No. Description

73-3003 Retaining Ring 82-AL616 #6 x 1-Inch Cross-Recessed Pan-Head Type BT Tapping Steel Screw 99-080025 Leaf Switch 99-080026 24nch Black Plastic Washer 99-080028 Metal Shaft 99-080029 Nylon Washer 99-080030 Spring 99-080031 Bellows 99-080032 Flat Steel Washer 99-080033 Piastic Guard/Actuator 99-080036 Top Plate 99-080037 Switch Mounting Plate 99-080038 Nylon Switch Actuator 171021-001 Joystick Assembly

3-11

Page 40

Maintenance, Repair and Parts

Kangaroo™

C. Fluorescent Tube and Speaker

WARNING Before removing or repairing the speaker, fluorescent tube or fan, unplug the game. !f you drop a fluorescent tube and it breaks, it will implode! Shattered glass can fly 6 feet or more from the implosion. Use care when replacing any fluorescent tube.

Upright Cabinet i

To Replace Fluorescent Tube:

  • Atthe top front of the game, remove the three screws that secure the upper attraction-panel retainer to the cabinet. Loosen the three screws that secure the lower retainer to the cabinet. Lift the attraction panel up and out of its lower retainer.
  • Remove the cardboard locking tab at each end of the tube. Slightly rotate the tube up or down, and carefully remove it from the lampholders. Replace with a new tube. Do not snap the tube in vigorously—you may break it, causing an implosion! Replace the locking tabs. Check that the green ground wire is securely attached to the large metal bracket and the ballast transformer on the wood board. If the tube is not grounded, it may not start.

To Replace Speaker: Remove the two Phillips-head screws that secure the light board to the cabinet. Slide the board out and unplug the 5-pin harness connector. Remove the board from the cabinet. Unplug the two plug-in connectors on the speaker. Remove the hardware that attaches the speaker to the board. Replace the speaker, and reinstall in reverse order.

Disassemble in the order indicated. (Circled numbers match the numbered instructions.)

Figure 3-5 Fluorescent Tube and Speaker

3-12

Page 41

Kangaroo™ Maintenance, Repair and Parts

NOTE To ensure that the fluorescent tube starts, make sure the green ground wire is firmly attached to both the ballast transformer and the steel lamp bracket.

037469-01 (Bracket) 148001-001 (Speaker)

179035-001 (Lampholder)

A037457-01 79-561816P (Hamess) (Wire Nut)

70-304 (Tube) 142028-xxx (Transformer) 99-11003 (Starter) A037540-01 (Grd. Wire) 99-11009 (Socket) 99-11006 (Tab)

Figure 3-5 Fluorescent Tube and Speaker, continued Upright Cabinet Assembly A037417-01 and -02 G Parts List

Part No. Description

A037457-01 Fluorescent Tube and Speaker Harness A037540-01 Ground Wire with Ring Lug 70-304 18-Inch 15W Cool White Fluorescent Tube 79-561816P Spring-Connector Wire Nut for 16- to 18-Gauge Wires 99-11003 Fluorescent Lamp Starter 99-11006 Fluorescent Lamp Locking Tab (tab consists of two pieces) 99-11009 Starter Socket 037469-01 Steel Lamp Bracket 142028-001 60 Hz 118V Ballast Transformer (used on A037417-01 assembly) 142028-002 50 Hz 118V Ballast Transformer (used on A037417-02 assembly) 148001-001 6x9Inch 4-Ohm 15W Oval High-Fidelity Speaker 179035-001 2-Pin Fluorescent Lampholder

3-13

Page 42

Maintenance, Repair and Parts

WARNING Prior to removing or repairing the speaker, fluorescent tube or fan, unplug the game. If you drop a fluorescent tube and it breaks, it will implode! Shattered glass can fly 6 feet or more from the implosion. Use care when replacing any fluorescent tube.

lreland-Built Cabinet * To Remove the Tube and Speaker Board: 1. From the back of the game, unlock and open the rear access panel. Unplug the tube and speaker’s 5-pin harness connector. Open the control panel (see Figure 3-2, The Control Panel). From the top front of the game, remove the five button-head screws that secure the upper cabinet grille to the cabinet. Lift the grille up and away from the cabinet. Be careful that the glass display shield doesn’t fall forward. Lift the video display shield up and out of the cabinet. Slide the baffle board that is below the fluorescent tube out through the front of the cabinet. Kangaroo™

  • Remove the screws that secure the tube and speaker board to the cabinet. Slide this board up and out of the cabinet.

To Replace Fluorescent Tube:

  • Remove the Y-lead connectors at each end of the fluorescent tube.
  • Slightly rotate the tube up or down, and carefully remove it from its clamps. Replace it with a new tube. Do not snap the tube in vigorously—you may break it, causing an implosion! Replace the Y-lead connectors. Reinstall the light and speaker board, baffle board, shield, grille, and reconnect the harness. Close and lock the control panel and the rear access panel.

To Replace The Speaker:

  • Unplug the two plug-in connectors on the back of the speaker.
  • Remove the hardware that attaches the speaker to the board. Replace the speaker and reinstall the hardware and two plug-in connectors. Reinstall the light and speaker board, baffle board, shield, grille, and reconnect the harness. Close and lock the control panel and the rear access panel.

Disassemble in the order indicated. (Circled numbers match the numbered instructions.)

3-14 Figure 3-5 038226-01 (Gillie)

©) 93821701 (Battle Board)

038439-01 (Shiela)

Fluorescent Tube and Speaker, continued

Page 43

Kangaroo™ Maintenance, Repair and Parts

148001-001 038219-03 (Speaker) (Light & Spkr. Bd.) 038151-01 A038253-01 (dmpr. Wire) (Harness)

142028-002 (Transformer) 99-11003 (Starter)

99-11009 (Socket)

Disassemble in the order indicated. (Circled numbers match the numbered instructions.)

NOTE To ensure that the fluorescent tube starts, make sure the ground wire is firmly attached to 99-1012 (Clamp) 70-303 (Tube) the transformer.

Figure 3-5 Fluorescent Tube and Speaker, continued lreland-Built Cabinet A038228-01 B Parts List

Part No. Description A038253-01 Tube and Speaker Harness Assembly 70-303* 18-Inch, 1-Inch Diameter, 15 W Cool White Fluorescent Tube 99-11003 Fluorescent Tube Starter 99-11009 Starter Socket 99-11012* 1% -Inch Fluorescent Tube Clamp 035835-01 12-Inch Y-Lead Connector 038151-01 Jumper Wire 038217-01 Baffle Board 038219-03 Tube and Speaker Board 038226-01 Cabinet Grille 038689-01 Display Shield 142028-002 50 Hz, 118 V Baliast Transformer 148001-001 6x 94nch, 42, 15 W Oval High-Fidelity Speaker

  • Acceptable substitutes are part numbers 70-304 (tube) and 99-11011 (clamp). They must be used together.

3-15

Page 44

Maintenance, Repair and Parts Kangaroo™

D. Video Display To Remove Video Display: . Open the rear access panel. Unplug the three display

WARNING harness connectors and disconnect the green ground Shock Hazard wire. The following procedure should only be per- Remove the hardware that secures the rear of the Upformed by a qualified service technician. Prior right cabinet display chassis to a wood cleat. Remove to removing or repairing the video display, unthe hardware that secures the /re/and-Built cabinet displug the game. As an extra precaution, we play chassis to a metal bracket. highly recommend you discharge the high volt- Open the control panel (see Figure 3-2). For the Ireland: age from the picture tube. Built cabinet, remove the 5 button-head screws that se- High voltages may exist in any video display, cure the upper cabinet grille to the cabinet (see Figure even with power disconnected. Use extreme 3-5). Lift the grille up and away from the cabinet.
caution and do not touch electrical parts of the . Li i i hield id out . display yoke area with your hands or with met- 4. Lift the video display shield up and out of the cabinet. al objects in your hands! 5. Carefully remove the cardboard bezel. Implosion Hazard 6. Remove the four sets of hardware that secure thefront If you drop the display and the picture tube of the display chassis to the wood frame. breaks, it will implode! Shattered glass and the 7. Carefully pull the display out through the front of the yoke can fly 6 feet or more from the implosion. cabinet. Place the display on a padded table in a pro- Use care when replacing any display. tected area so that nothing can hit it or fall on it. After servicing the display, reinstall in reverse order. nN

Disassemble in the order indicated. (Circled numbers match the numbered instructions.)

  • 038226-01 (Grille)

038419.01 (Shield)

038439-01 (Shield) 037750-01 (Bracket) 038232-01 (Bezel)

Figure 3-6 Video Display

3-16

Page 45

Kangaroo™ Maintenance, Repair and Parts

Figure 3-6 Video Display, continued Parts List

Part No. Description

Upright Cabinet 92-049 19-Inch Electrohome Color Raster-Scan Video Display Acceptable substitutes are: 92-055, Wells-Gardner 19-Inch Display—use with TM-201 139003-1005 or -1205, Sanyo 19-Inch Display—use with TM-205 139003-1004 or -1204, Matsushita 19-Inch Display—use with TM-197 037443.01 Display Bezel 038419-01 Display Shield with Graphics Ireland-Built Cabinet 92-049 19-Inch Electrohome Color Raster-Scan Video Display Acceptable substitute is part no. 92-055—use with TM-201 037750-01 Display Mounting Bracket 038439-01 Display Shield with Graphics 038226-01 Upper Cabinet Grille 038232-01 Display Bezel

Page 46

Maintenance, Repair and Parts Kangaroo™

E. Coin Door

170000-001 (Lamp) 99-15023 sr90a7001 we . (Base Plate)

(Lamp Base) &

a 99-15040 “ 99-15026 (Lever) (Coin Inlet) ‘ 99-15056 (Screw for Bezel)

(Coin Inlet)

PART OF 99-15069

99-15054 99-15055 hy 99.15068 (Pivot for Lever)

(Retng. or (Lockout Coil)

99-15069 (Lockt. Coil Spring) ~"

99-15027 (Coin Ret. Box)

PR 75-9148 x I» Im_—- 99.15028 (Hex Nut) (Coin Ret. Box)

75-056 (Lock Wash.) 99-15037 (Sw. Adjuster) 99-15056 (Screw for Bezel)

99-15029 (Bracket) 99-1 _ ~ (Switch)

7534148 (crew)

7214148 (Screw)

Figure 3-7 Vertically Mounted Coin Door A037619-xx C

3-18

Page 47

Kangaroo™

$9-15073 (Upper Door),

9915063 Screw)

99-15067 (Lock Assy.)

A037491-01 (Coin Box)

03754201 (Harness—not shown)

A037619-01 — U.S. 25¢/25¢ Coin Door A037619-02 — U.S. 50¢/50¢ Coin Door ‘A037619-03 — Canadian 25¢/25¢ Coin Door ‘A037619-04 — British 10 P/10 P Coin Door A037619-05 — British 10 P/50 P Coin Door A037619-06 — British 20 P/50 P Coin Door A037619-07 — Australian 20c/20¢ Coin Door 98-15067 (Lock Assy.)

A037619-08 — German 1 DM/1 DM Coin Door ‘A037619-09 — German 2 DM/1 DM Coin Door A037619-10 — German 2 DM/5 DM Coin Door ‘A037619-11 — German 1 DM/S DM Coin Door A037619-12 — 5 Fr/S Fr Coin Door A037619-13 — Swiss 1 Fr/1 Fr Coin Door ‘A037619-14 — French 1 Frit Fr Coin Door Maintenance, Repair and Parts

99-15001 thru 99-15011 (Ret. Button)

99-15072 (Door Frame)

99-15071 (Clamp)

99-15039 (Bezel for Cover) |

99-15036

99-15066 (Screw)

99-5074 (Lower Door)

‘A037619-15 — French 2 Frit Fr Coin Door ‘A037619-16 — Swedish 1 Kr/1 Kr Coin Door A037619-17 — Spanish 25 Pts/25 Pts Coin Door A037619-18 — Italian 100 L/100 L Coin Door ‘A037619-19 — Hong Kong $1/$1 Coin Door A037619-20 — Japanese 100Y/100Y Coin Door

Figure 3-7 Vertically Mounted Coin Door, continued A037619-xx C

3-19

Page 48

Maintenance, Repair and Parts Kangaroo™

Figure 3-7 Vertically Mounted Coin Door,continued Parts List

Part No. Description A037491-01 Coin Box (Not included in assembly) A037542-01 Hamess Assembly 72-1405S #4-40 x ¥--Inch Cross-Recessed Pan-Head Steel Machine Screw 7214148 #4-40 x %-Inch Cross-Recessed Pan-Head Steel Machine Screw 75-056 #6 Internal-Tooth Zinc-Plated Steel Lock Washer 75-914S #4-40 Stee] Machine Hex Nut 75-3414S, #4-40 x %-Inch 82° Cross-Recessed Flat-Head Stee! Machine Screw 99-15001 Coin Return Button with U.S. 25¢ Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate 99-15003 Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20¢ Price Plate 99-15011 Coin Return Button with Italian 100 Lire Price Plate 99-15023 Base Plate 99-15025 Left Haif of Coin Inlet 99-15026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box 99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99.15030 Flap for Lockout Coil (U.S. 25¢) 99-15036 Metal Coin Return Cover 99-15037 Switch Adjuster 99-15038 Bezel for Coin Return Button 99-15039 Metal Bezel for Coin Return Cover 99-15040 Coin Return Lever 99-15042 Coin Switch for U.S. 25¢ 99-15052 Spring for Coin Return Button 99-15054 Pivot for Coin Return Lever 99-15055 Retaining Screw 99-15056 Screw for Both Bezels 99-15060 Switch Cover 99-15063 ‘Screw for Hinge 99-15066 Screw for Clamp 99-15067 Lock Assembly 99-15068 Lockout Coil 99-15069 Spring for Lockout Coil 99-15071 Clamp for Frame 99-15072 Door Frame 99-15073 Upper Door 99-15074 Lower Door 170000-001 6.3V Miniature Wedge-Base Incandescent Lamp 474006-035, Metal Coin Mechanism 179047-001 Lamp Base

3-20

Page 49

Kangaroo™

F. Printed-Circuit Boards

WARNING

Prior to removing or repairing any printed-circuit board, unplug the game.

To Remove Printed-Circuit Boards: 1, Open the rear access panel.

  • For the game PCBs, unplug the edge connectors. Remove the wood screws that attach the top cleat to the game cabinet, and remove this cleat. The sides of the video PCB are secured by plastic retainers. To release this PCB from the retainers, gently pry the retainers away from the PCB.
  • Carefully remove the PCBs from the slots in the bottom cleat. Be careful not to twist the boards, as this may loosen connections or components. Repair as required. @ Reinstall the game PCBs, making sure they fit securely into the slots of the bottom cleat. Maintenance, Repair and Parts

@ Gently pry the plastic retainers back and secure the video PCB in these retainers. Jo insure that the game PCBs will not be damaged when you move the game, be sure to reinstall the top cleat.

  • For the Regulator/Audio |! PCB, disconnect the four mail harness connectors on this board.
  • Remove the screw and two spacers that secure this board to the cabinet and carefully remove the board from its slot. Be careful not to twist the board, as this may loosen connections or components. Repair as required and reinstall the board. @ Make sure that the connectors on the game or Regulator/Audio I! PCBs are properly plugged in. Note that they are keyed to fit only one way, so if they don’t slip on easily, don’t force them. A reversed connector will probably damage your game and void the warranty. Close and lock the rear access panel. @ Check that the operation of the game is correct by performing the self-test. This is very important when you repair a PCB.

038423-03 (Cleat)

82-1820S (Screw)

171025-001 (Interconnector)

171023-001 (CPU PCB)

034536-02 (Vibra Damp.)

(Regulator! Audio i! PCB)

Remove in the order indicated. (Circled numbers match the numbered instructions.) 171024-001 (Video PCB)

035745-09 (Retainer)

034536-01 (Vibra. Damp.)

038423-03 @ (Cleat)

175004-708 (Spacer)

72-6810S (Screw)

Figure 3-8 Printed-Circuit Board Removal

3-21

Page 50

3-22 Figure 3-9 Kangaroo™ Central Processing Unit PCB Assembly 171023-001

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING

nse to use, the subject matter of the

hnical information shown thereon, nor

Except for

‘manufacture under the

en ter TRU 1c20_ asco eas

Pasoe faces Je -0,@ 226 TALS OA

2 1eze

74842 vere tile [a2ne | cos 741504] ane x 74.504

Les tow Op) Tee. 23c372

(e13,

Fal S307 =eD cA raLsoe7 7ALSOO ?. 1c29

rept 3 custom

aD ars » [arsscr] 0 [ocees]

cS 90-703 nee 90-7036 BAL ATK 1c37 me cas — Ni

1e44 1cae ces cra COB C45 Se passe] GOR EO eri atone

aD Tacs308 (Fes BRS

ikea D760 3,470

=e c4,470T > SD 29 eve

v7 e z ica? 1cS3

Py al p 1 68,470 [ae s3e7] ee, 1000 > icte loag lego 1c40

Romo

pace 14] FeLe3e <> QP i 7405175 ep

Pas 75 facsi7s [Patsoo] Paus3e7 148 154

oe eons | teat cat ica ess ]

(cae) 741532] Passe] = [maser

rete

eomt Sp Roms Tose 9o-7e3~

Rome 1eto Roms Blo os 3308 =D ep 1650 Auo1O Ar3-8310 =p MB 3713. Maintenance, Repair and Parts Kangaroo™

Page 51

Kangaroo™ Maintenance, Repair and Parts

Figure 3-9 Kangaroo™ Central Processing Unit PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold) 34-2N6044 Type-2N6044 Darlington NPN Transistor (TR-3, TR-4)

37-74LS00Type-74LS00 Integrated Circuit(IC13, 48)
37-74LS04Type-74LS04 Integrated Circuit(IC12, 35, 36)
37-74LS32Type-74LS32 Integrated Circuit(1C11, 21, 40, 41, 49)

37-74LS42 Type-74LS42 Integrated Circuit (IC2, 31)

37-74LS74Type-74LS74 Integrated Circuit(IC30)
37-74LS139Type-74LS139 Integrated Circuit(IC1)
37-74L8175Type-74LS175 Integrated Circuit(IC38, 47, 52, 53, 58, 59)
37-74LS245Type-74LS245 Integrated Circuit(IC23)
37-74LS367Type-74LS367 Integrated Circuit(IC3, 4, 14, 37, 39, 54, 55)

62-001 SPST Momentary Pushbutton Switch (SERVICE SW) 66-118P1T 8-Station SPST, Dual-Inline-Package Switch (DIP SW) 79-42C24 24-Contact Medium-Insertion-Force Integrated Circuit Socket (IC7-10, 16, 17, 24, 28) 79-42C40 40-Contact Medium-Insertion-Force Integrated Circuit Socket (IC 15, 34, 50) 82-1820S #8 x 114-Inch Flat-Head Wood Screw (for mounting PCB to cabinet) 90-7036 Random-Access Memory {IC5, 6, 32, 33) 034536-01 Foam Vibration Damper 035745-09 Plastic PCB Retainer (for mounting PCB to cabinet) 03842303 Dual Slotted Wood Cleat (for mounting PCB to cabinet) 110000-101 100 Ohm, +5%, %W Resistor (R27-49, 52, 53) 110000-102 1K Ohm, +5%, %4W Resistor (R50, 51, 61) 110000-103 10K Ohm, +5%, %W Resistor (R2, 5, 64, RX) 110000-122 1.2K Ohm, +5%, “4W Resistor (R7) 110000-203 20K Ohm, +5%, %4W Resistor (RA) 110000-221 220 Ohm, +5%, %4W Resistor (R8) 110000-331 330 Ohm, +5%, %W Resistor (R9, 10)

110000-3323.3K Ohm, +5%, %4W Resistor(R6)

110000-472 4.7K Ohm, +5%, YW Resistor (Rt)

110000-51051 Ohm, +5%, %W Resistor(R3)

110000-512 5.1K Ohm, +5%, YW Resistor (R62) 118001-472 4.7K Ohm, 4-Element, 5-Pin, Single-Inline-Package Resistor Network (RA2) 118002-222 2.2K Ohm, 8-Element, 9-Pin, Singie-Inline-Package Resistor Network (RA3-6) 118002-472 4.7K Ohm, 8-Element, 9-Pin Single-Inline-Package Resistor Network (RA1) 119003-102 1K Ohm +20% Horizontal Trimpot (VR2) 121015-103 .01 pF, + 10%, 50V Radial-Lead Ceramic-Disc Capacitor (C7-30) 121015-104 .1 uF, + 10%, 50V Radial-Lead Ceramic-Disc Capacitor (Bypass, 26 places) 121020-101 100 pF, + 10%, 50V Radial-Lead Ceramic-Disc Capacitor (C2) 121020-102 1000 pF, + 10%, 50V Radial-Lead Ceramic-Disc Capacitor (C6) 121020-471 470 pF 50V Radial-Lead Ceramic-Disc Capacitor (C3-5, 34) 121021-105 1yF, + 10%, 16V Tantalum Capacitor (C35) 121022-104 0.1 uF, + 10%, 50V Polyester Film Capacitor (C36) 123004-101 100 pF, + 20%, 16V (min.) Aluminum Electrolytic Fixed Radial-Lead Capacitor (C42) 123004-470 47 uF, + 20%, 16V (min.) Aluminum Electrolytic Fixed Radial-Lead Capacitor (C39-41) 123004-471 470 uF, + 20%, 16V (min.) Aluminum Electrolytic Fixed Radial-Lead Capacitor (C37)

[Continued on next page]

3-23

Page 52

Maintenance, Repair and Parts Kangaroo™

Figure 39 Kangaroo Central Processing Unit PCB, continued Parts List

Part No. Description

123005-225 2.2 uF, + 20%, 5OV (min.) Aluminum Electrolytic Fixed Radial-Lead Capacitor (C1) 123006-106 10 uF, +20%, 16V (min.) Aluminum Electrolytic Fixed Radial-Lead Capacitor (C38) 133010-001 Type-2SC372 NPN SOV 400mW Transistor (TR1, 2)

436008-101Programmable Read-Only Memory, #75(IC7)

136008-102 Programmable Read-Only Memory, #76 (IC8)

136008-103Programmable Read-Only Memory, #77(IC9)
136008-104Programmable Read-Only Memory, #78(\C-10)
136008-105Programmable Read-Only Memory, #79(IC16)
136008-106Programmabie Read-Only Memory, #80(IC 17)
136008-107Programmable Read-Only Memory, #81(IC24)

136008-112 Programmable Read-Only Memory, #82 (IC28)

137168-001Type-74LS368 Integrated Circuit(IC42-46, 51)
137177-001Type-74LS138 Integrated Circuit(IC22)

137194-001 Z80 Microprocessor (IC15, 34)

137221-001Type-74LS155 Integrated Circuit(IC20)

137222001 Type-G.|. AY3-8910 Sound Integrated Circuit (IC50) 137223-001 Audio Amplifier Integrated Circuit (IC61) 137224-001 Microcomputer Custom Integrated Circuit (IC29) 171022-001 CPU PCB, Video PCB and Interconnector Assembly 171023-001 Central Processing Unit PCB Assembly 171025-001 50-Pin Flat Cable PCB Interconnector, Fujitsu FCN-707B050-AU/B 179100-050 50-Pin PCB Mount Connector, Fujitsu FCN-705Q050-AU/M (CN1)

3-24

Page 53

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 54

3-26 Figure 3-10 Kangaroo™ Video PCB Assembiy 171024-001

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING

CONFIDENTIAL: Reproduction forbidden without the specific written

Permission of Atari, Ine,, Sunnyvale, CA. This drawing ts only condi-

tionally issued, and neither receipt nor possession thereof conters or

transfére any right in, or license to use, the subject matter of the

drawing or any design oF technical information shown thereon, nor

any right Yo raproduce this drawing or any part thereat. Except for ‘manufacture by vendors of Atari Inc. and for manufacture under the ht is granted to reproduce this,

corporation's written license, no Srawing or the subj ‘matter thereof, untess by written agreement

with or written permission from the corporation’

1 ere [csi] Pacis tee eis 7aLsies] [74lsi57 a> 163 ars icas 1e50 reed ree

Tats les farsies 74L 5123) 1ca7 te1or fous: 1129

fausi7s]| frases 741504] [cere

lest eos, tard

7aLsi57 Tals 157) 7acsis7 | cae Leto rales (e130

favors) [restes] facsies pacsi7a

D>. @Dp asp ese 152 fac) 1o7e, fare) 1689 Ge 1103 ca ara

vatoi7s | [ausica] [rarsis7 Tasso? ae ice 11s ic2e 1639 ROMVI om VO

zaisi7s] [atsics] [7419157 7408307]

aD 1c27 74508 1es3 1077

faisse7 cao Rom v3 romve

1e2e teat ese ces. 107% qacsee] farsns parsio

1290 races rans hatsoo e132 4S 74

TALS3e 744837 ear e105 fran (e133

7aiso4] [74Ls00 peoe, icloe F4Lsio 1c120 741910 leig4

74 ts74] rave 7a] frasis7 TaLsi57| [assy fsxso0

wee 1c29 PP icss GD

icaz

a (Tsrtg] tera 74153 footy 00! ap Z ais t57] @ fais0o tector Dress

[ees Rarsoo. fiacsoo ] s

ce a> tes fraird 30

he 1c43 tose 1ce7 ico toga e108, 1e13@

as74 74Ls04| [rarsae 74153, ficoot-cor 100017-004 [fove17-0o] fares

lee tere. (eat 1o44 1es7 1668 1eBt

qasta] [raesizs] Pause [(30017-00] foe 7-00 as e109 1e137

aS 1c? frat 1632 74153] [ooor-20] teas, e568 1eee 1caz qe eto, pacer e136

[rss] [Farsoo] [racsaq 74153] [looted]

ice ic2o Dies a> Diese C59

paso 744508] [rausec

pene 4, 33 BSR ica (cat 1e34 74153 | fiocer7-cey a> 1¢70 io0017-00)| fooancol] arsis7 74L 932]

a> fooore/] , Koro) rears <b e139

feoorreal] [resis]

1ea7, 1eco

Pasa] [asses] [asee [72183] [oeer-00l

mi tcrio GDDieze e358) 1cae teat

passe] [acsto] [Tausaed eu le2s leoe [ecorneal (o00lr-ol lez (cea rer reve. pacsas te12e se140

feeonves [coorr-eai| [74L8 15 7) Pais 95] parse 74L500

as 199 ons rated

Iacono] feoorrco] [arsts7] pas 95 tctat Faieie]

1cag rece 173, cee (c100 lena (rar rare

aisoa 74L5393) qaLsBe 74153 fisoer?-00] a> jiecorr-oo1 Freorroo] ffoooi pansis7 pasos rarese

fares a> far) 78-B010018 Riz Ru Rip Ra =e E cua 2) logy, tev L Maintenance, Repair and Parts Kangaroo™

Page 55

Kangaroo™ Maintenance, Repair and Parts

Figure 3-10 Kangaroo Video PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold)

37-74153Type-74153 Integrated Circuit(IC42-49)
37-74LS00Type-74LS00 Integrated Circuit(IC 19, 105, 106, 118, 120, 134, 135, 139)
37-74LS04Type-74LS04 integrated Circuit(IC8, 11, 17, 91, 115, 117)
37-74LS08Type-74L.S08 Integrated Circuit(IC20, 27)
37-74LS10Type-74LS10 Integrated Circuit(IC22, 119, 131, 133, 137, 141)
37-74LS32Type-74LS32 Integrated Circuit(C10, 89, 90, 104, 136, 138, 140, 142)
37-74LS74Type-74LS74 Integrated Circuit(IC5, 6, 9, 28, 41, 132)
37-74LS86Type-74LS86 Integrated Circuit(IC30, 32-36)
37-74LS95Type-74LS95 Integrated Circuit(IC121-128)
37-74LS157Type-74LS157 Integrated Circuit(IC 12, 13, 25, 26, 51, 54, 64, 65, 75, 78, 92, 107-114)
37-74LS163Type-74LS163 Integrated Circuit(C14, 2, 14, 15, 50, 63, 74, 88, 102, 116)
37-74LS174Type-74L.S174 Integrated Circuit(1C129, 130)
37-74LS175Type-74LS175 Integrated Circuit(IC3, 4, 7, 16, 18, 87, 101, 103)
37-74LS193Type-74LS193 Integrated Circuit(1C29, 31)
37-74LS367Type-74LS367 Integrated Circuit(IC38-40)
37-74LS393Type-74LS393 Integrated Circuit(IC21, 23)

78-801001F PCB Plastic Standoff 79-42C24 24-Contact Medium-Insertion-Force integrated Circuit Socket (I1C52, 53, 76, 77) 90-123 10MHz Crystal (XTAL—Left of 1C9) 100017-001 Random-Access Memory (IC55-62, 66-73, 79-86, 93-100)

110000-1221.2K Ohm, +5%, %W Resistor(R4)
110000-221220 Ohm, +5%, YW Resistor(R1, 3, 9-12)
110000-561560 Ohm, +5%, “4W Resistor(R2)
121015-104-1yF, + 10%, 50V Radial-Lead Ceraric-Disc Capacitor(Bypass, 38 places)
121020-33033 pF, + 10%, 10V Radial-Lead Ceramic-Dise Capacitor(C4)
123004-101100 uF 16V Aluminum Electrolytic Radial-Lead Capacitor(C1, 3)
136008-108Programmable Read-Only Memory, #83(IC76)
136008-109Programmable Read-Only Memory, #84(IC52)

136008-110 Programmable Read-Only Memory, #85 (IC77)

136008-111Programmable Read-Only Memory, #86(IC53)
179100-05050-Pin PCB Mount Connector, Fujitsu FCN-705Q050-AU/M(CN1)

3-27

Page 56

Maintenance, Repair and Parts

3-28 L oa Qa

c|cx;Q
sleer4=|9

cRS =- roy co ac

eryar00es

x C19 x

—+3300rt

35v

S300 + —| pty C23 cl

SovQitl+F22+

R25 4rieF- ez}

fcee,CBAC

5.6K 308 Q9pe=s 7812 7905

oO —R24,10,7 Wh oO

+ Bs

Figure 3-11 Kangaroo™

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the spe- Citic written pemmission of Atan, Inc, Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereof confers of transfers any right in, of I Gense to use, the subject matter of the drawing or any desian or technical information shown thereon, nor any Fight to reproduce this drawing or any part thereot. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's wiitten license, no right to repro- ‘duce this drawing is granted or the subject matter thereo! unless by written agreement with or written permission from the corporation.

Regulator/Audio || PCB Assembly A035435-06 B

Page 57

Kangaroo™ Maintenance, Repair and Parts

Figure 3-11 Regulator/Audio Il PCB Assembly Parts List

Part No. Description (Reference Designations and Locations in Bold) 19-100P1015 .1Ohm, +3%, 7W Wirewound Resistor (R24) 19-315102 1K Ohm Vertical PCB-Mounting Cermet Trimpot (R8)(Acceptable substitute is part no. 119002-102.) 24-250108 1000 wF 25V Aluminum Electrolytic Fixed Axial-Lead Capacitor (C13) 24-250477 470 uF 25V Aluminum Electrolytic Fixed Axiai-Lead Capacitor (C1) 24-350226, 22 uF 35V Aluminum Electrolytic Fixed Axial-Lead Capacitor (C24, 31) 24-350338 3300 uF 35V Aluminum Electrolytic Fixed Axial-Lead Capacitor (C18, 19) 24-500105 1 yF 50V Aluminum Electrolytic Fixed Axial-Lead Capacitor (C22, 23) 29-088 1 uF 50V Ceramic-Disc Axial-Lead Capacitor (C20, 21) 31-1N4002 Type-1N4002 100V 1-Amp. Silicon Rectifier Diode (CRI, 4) 31-1N5401 Type-1N5401 100V 3-Amp. Silicon Rectifier Diode (CR5-8) 33-TIP32 Type-TIP32 PNP Power Transistor (Q2)

34-2N3055Type-2N3055 NPN Silicon Transistor(Q3)

37-LM305 SV Linear Voltage Regulator (Q1)

37-7812Type-7812 + 12V Voltage Regulator(Q8)
37-7905Type-7905 —5V Voltage Regulator(Q9)

72-1608C #6-32 x ¥2-Inch Cross-Recessed Pan-Head Corrosion-Resistant Steel Machine Screw

72-6812S#8 x %4-Inch Phillips-Head Wood Screw(for mounting PCB to cabinet)

75-F60405 #632 x ¥%4-Inch Binder-Head Nylon Screw 75-99516 #6-32 Nut/Washer Assembly

78-16014Thermally Conductive Silicon Insulator(Q2, 9)

79-58306 6-Position Connector Receptacle (J6, 9) 79-58308 9-Position Connector Receptacle (J7) 79-58346 12-Position Connector Receptacle (J10) 03453101 Heat Sink 034536-02 Foam Vibration Damper (goes between PCB and cabinet wall) 110000-100 10 Ohm, +5%, %W Resistor (R29, 30)

110000-101100 Ohm, +5%, %4W Resistor(R4)
110000-271270 Ohm, +5%, “%4W Resistor(Ri)

110000-330 33 Ohm, +5%, ¥%4W Resistor (R3) 110000-392 3.9K Ohm, +5%, YW Resistor (R6) 110000-562 5.6K Ohm, +5%, YW Resistor (R32, 33) 110000-752 7.5K Ohm, +5%, %4W Resistor (R7)

110009-0272.7 Ohm, +5%, 1W Resistor(R5)

116000-220 22 Ohm, + 5%, 10W Wirewound Resistor (R31)

116001-0404 Ohm, +5%, 5W Wirewound Resistor(R25)

122002-102 .001 uF 50V Ceramic-Disc Axial-Lead Capacitor (C2) 122004-224 .22 uF 25V (min.) Ceramic-Disc Axial-Lead Capacitor (C8) 175004-708 Fiber Spacer (for mounting PCB to cabinet) 179051-001 Test Point (Acceptable substitute is part no. 020670-01)

3-29

Page 58

Maintenance, Repair and Parts Kangaroo™

G. Power Supply Assembly

A035888-01 (Transformer) 29-053 (Capacitor)

A021084-xx (Volt. Plugs) Fuse cover must be in place during game operation. 034544.01 (Fuse Block Cvr.)

79-4411001 (Fuse Post) 78-70501SC (Cap. Bracket)

A6-2017002 (Fuse)

A035891-01 (Fuse Harness) 034482-02 A (Chassis) 46-301203

037639-01 (Label)

78-2708 (Bushing)

A034630-01 (Fuse alee) (Filter Assy.) eh, ' 46-2014002 (Fuses)

79-15021001 ‘A035890.01 (Term. Block) (Pwr. Harness)

A034629-01 3A-MDA3501 (AG. Harn.) (Rectifier)

Figure 3-12 Power Supply Assembly A037671-01 and -02 C

3-30

Page 59

Kangaroo™ Maintenance, Repair and Parts

Figure 3-12 Power Supply Assembly, continued Parts List

Part No. Description (Reference Designations in Boldj A021084-01 Voltage Plug for 100 V_ (violet)

A021084-02Voltage Plug for 120 V_(yellow)
A021084-04Voltage Piug for 220 V(blue)
A021084-05Voltage Plug for 240 V(brown)

A034629-01 AC Harness Assembly

A034630-01RFI Filter Assembly(FL1)

A035888-01 Upright Transformer Assembly (11) (Acceptable substitute is part no. A035888-02) A035890-01 Power Harness Assembly A036891-02 Fuse Harness Assembly 29-053 27,000 pF, 15 VDC Electrolytic Capacitor (C1) 3A-MDA3501 Type-MDA 3501 Bridge Rectifier (CR1) 46-2014002 4 A, 250 V, 3AG Slow-Blow Glass Cartridge-Type Fuse (F2, F4-F6) 46-2017002 7 A, 250 V, 3AG Slow-Blow Glass Cartridge-Type Fuse (F1) 46-301203 20 A, 32 V, 3AG Slow-Blow Glass Cartridge-Type Fuse (F3) 78-2708 Nylon Type 6/6 Hole Bushing with %-Inch Inside Diameter x %%{.-Inch Outside Diameter x V-Inch Thick 78-70501SC 2-Inch Diameter Capacitor Mounting Bracket 79-15021001 2-Circuit Single-Row Terminal Block 79-3206 §-Position 3AG Fuse Block with %-Inch Quick-Disconnect Terminals 79-4411001 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post 034482-02 Power Supply Chassis 034544-01 Fuse Block Cover 037243-01 Metal Base Plate (goes under the power supply—not shown in illustration)

037639-01Label for Fuse Value(F1)
037641-01Label for Fuse Values(F2-F6)

Line Voltage Range 90-110 VAC (100) 105-135 VAC (120) 200-240 VAC (220) 220-260 VAC (240) Voltage Selection Plug Wire Color Violet Yeliow* Blue Brown “This is the only plug provided on the North American power supply.

NOTE

A037671-01 power supply assembly has the 120V plug A037671-02 has the 100V, 220V and 240V plugs A037671-03 has the 220V and 240V plugs

3-31

Page 60

NOTES:

Page 61

NOTES:

Page 62

NOTES:

Page 63

YOUR COMMENTS, PLEASE!

Kangaroo 4th printing

Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below. No postage stamp is necessary if mailed in the U.S.A.

lf you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name.

Firm CO Distributor

Address. (3 Operator City State Zip O Other.

Area Code Phone

Page 64

First fold

No Postage Necessary if mailed in the United States

BUSINESS REPLY MAIL a FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA es

POSTAGE WILL BE PAID BY ADDRESSEE Le Atari, Inc. | Attn.: Field Service/Coin-Op Division es P. O. Box 427 Sunnyvale, California 94086 i

a

Second fold

wold ebpe sy) adey

Page 65

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below.

{f you have any technical questions about certain ATAR! games products, or are requesting additiona! publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name.

Firm U Distributor

Address 1 Operator City Country 0 Other. Kangaroo 4th printing

Phone City Code Country Code -

Page 66

First fold

Attach Necessary Postage

Atari Ireland Limited Attn.: Field Service/Coin-Op Division Tipperary Town, Ireland

eGpe siuy adel

Page 67

9 EE REE ILE

> > ° > > >

Warranty

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays (in games supplied with displays) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted

If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, al its option, to repair, replace. or credit Buyer's account for such products which are returned to Seller during said warranty period, provided

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective:
  • Such products are returned prepaid to Sellers’ plant, and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident. misuse. neglect. alteration, improper repair. installation or improper testing

In no event shail Seller be liable for loss of profits, loss of use, incidental or consequential damages.

Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety.

Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.

This document is and contains confidential trade secret information of Atari, Inc.

This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever. and remains the property of Atari, Inc.

Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc. : : : : : : :

Page 68

ATARI INC 790 SYCAMORE DRIVE P.O. BOX 906 MILPITAS, CALIFORNIA 95035 408/942-3100 ¢ TELEX 35-7488 ss

SP a Mic