Basketball TM-137 1st Printing
Basketball (Benchmark Games, set 1) (Benchmark Games, Inc., 2013) · Technical Manual · 72 pages · 43 sections · original scan
Operation,
Maintenance
and Service Manual Complete with Illustrated Parts Catalog 1st printing SUN LN iG
GAME SERIAL NUMBER LOCATION
Your game’s serial number is stamped on the circuit (back) side, bottom right corner, of the printed circuit board—see the illustration below. The same number is also stamped on the label located on the rear of the game cabinet. Please mention this number whenever calling your distributor for service. ta
SASKETBALL
Operation, Maintenance and Service Manual
Compiete with illustrated Parts Catalog
ATARI, INC. 1265 BORREGAS AVENUE P.O. BOX 427 SUNNYVALE, CALIFORNIA 94086, 408/745-2000 » TELEX 35-7488
A ATARI
Copyright © 1979 by Atari, Inc. All rights reserved
No part of this publication may be reproduced by mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.
For permission requests, write:
ATARI, INC 1265 Borregas Avenue P.O. Box 427 Sunnyvale, California 94086
5H
Lithographed in the U.S.A
ii Basketball™
table of
contents
location setup
A. INTRODUCTION . . B. GAME INSPECTION Cc. INSTALLATION REQUIREMENTS Low-Voltage Problems. . High-Voltage Problems INTERLOCK AND POWER ON/OFF SWITCH . bee SELF-TEST PROCEDURE .............--+ 1-5 VOLUME ADJUSTMENT OPERATOR OPTIONS emmys
game play
INTRODUCTION ... i cece cent eave ee ne es nee te ewes et ee ens ATTRACT MODE. PLAY MODE .... SELF.TEST MODE . soy
maintenance and adjustments
INTRODUCTION CLEANING ... GAME FUSES PLAYER CONTROL PANEL ..
- LED Start/Shoot/Jump Switches 0... 6.0.6 e cc cece eee 3.3
- Trak Ball™ Assemblies LOUDSPEAKERS ...... . 3 é FLUORESCENT LAMP ..... 2.0.00 ccc ccc cect neenenes TV MONITOR REMOVAL GAME PCB pop>
zOmm
Basketball™ iii
table of
contents
4 details of electronic operation
A. GENERAL INFORMATION. ...... 0.0000 cee cece eee eee 4-1 B. POWERSUPPLY........... 4-5 C. MICROCOMPUTER CIRCUITRY 4.6 MPU, ROM, and RAM . 46 Address Deceding . . . 46 ® 0 Clock Driver . - 4-6 Watchdog Reset ... 4-11 D. SYNC GENERATOR .. 4-11 E. PLAYFIELD GENERATOR... 4-11 F. MOTION OBJECT GENERATOR - 4.16 G, VIDEO SUMMING CIRCUIT .......0 +0000 eee eee e ee . 4.18 H. TRAK BALL™ CONTROL AND SWITCH INPUT CIRCUITRY.......... 4.19 I AUDIO CIRCUITRY .. 2... obec c ccc cette eee eens 4.19
5 illustrated parts catalog
list of
Table 1-1 Self-Test Procedure... 0... ccc ccc cece cnet e teens 1-6 Table 1-2 Faulty Circuits or Chips . . . 1-7 Table 1-3 Operator Option Switch Settings veer 19 Table 4-1 | Game PCBMemory Map .....--- 02-000 eee ce cence ee ees ...410
iv Basketbali™
list of
illustrations
Figure 1-1 Control Panel and Player Controls . . . 1-2 Figure 1-2 Voltage Selection Plugs 1-3 Figure 1-3 Power On/Off and Interlock Switches .. . 1-4 Figure 1-4 Volume Control and Self-Test Switch. . . Figure 1-5 Operator Option Switches . Figure 3-1 Game Fuses Figure 3-2 Hinging the Control Panel Open Figure 3-3 LED Start Switch Testing and Replacement . Figure 3-4 Trak Ball™ Assembly Removal Figure 3-5 Removing the TV Monitor . Figure 3-6 Removing the Game PCB ...
Figure 4-1 Game Block Diagram . . Figure 4-2 Game PCB Block Diagram . Figure 4-3 Game Wiring Diagram ... . Figure 4-4 Game PCB Power Distribution ....... Figure 4-5 MPU Circuit Schematic Diagram . . . . Figure 4-6 ROM Memory Schematic Diagram Figure 4.7 RAM Memory Schematic Diagram . . Figure 4-8 Address Decoding Schematic Diagram. . Figure 4-9 Sync Generator Schematic Diagram .. Figure 4-10 Playfield Generator Schematic Diagram Figure 4-11 Motion Object Generator Schematic Diagram ........... Figure 4-12 Video Output Schematic Diagram .......... Figure 4-13 Trak Ball™ and Switch Input Schematic Diagram . Figure 4-14 Audio Schematic Diagram . .
Figure 5-1 Final Assembly Figure 5-2 Fluorescent Light Assembly . Figure 5-3 Control Panel Assembly . . . Figure 5-4 Trak Ball™ Assembly. . . . Figure 5-5 Steering Board Assembly Figure 5-6 Type B Power Supply Assembly . . Figure 5-7 Coin Door Assembly Figure 5-8 Basketball Game PCB Assembly . . Figure 5-9 Audio PCB Assembly
Basketball™ v
WEST and CENTRAL U.S.A.
Atari Coin-Op Customer Service 1344 Bordeaux Drive, Sunnyvale, CA 94086 Telex 17-1103 (Monday - Friday, 7:30 - 4:00 pm Pacific Time)
From California, Alaska or Hawaii, dial (408) 745-2900
From anywhere else in this area, dial toll-free (800) 538-1611
EAST U.S.A.
Atari Inc. New Jersey Customer Service Office 44 Colonial Drive, Piscataway, NJ 08854 Telex 37-9347 (Monday - Friday, 8:30 - 5:00 pm Eastern time)
From New Jersey dial (201) 981-0490
From anywhere else in this area, dial toll-free (800) 631-5374
vi Basketball™
location setup
a. introduction
Basketball is a one- or two-player large-screen video game designed and made by Atari, Inc. It realistically simulates a “one-on-one” game between two basketbail players who can shoot, dribble from one position on the floor to another, jump, block shois, steal the ball, and maneuver for the open shot. Each player controls one of the “men” displayed on the video screen, or if there is only a single player, the game’s computer controls one man. The famous Atari Trak Ball™ also used in Football is employed to control the player images on the screen. The start/shoot/ jump buttons are used to start the game after coins have been deposited, (see Figure 1-1), and during game play, to cause a man to shoot the bail or jump to defend against the other man’s shots.
Basketball™
b. game inspection
Your game is manufactured ready to play upon removal from its shipping carton. Your cooperation is requested to supply the final touch of quality control to your game. Therefore, please follow these procedures to ensure that your game is in good condition:
2. Examine all external parts of the game cabinet for dents, chips, or broken parts. After determining that the game has been received in good condition, unlock and open the rear access panel. Carefully inspect the interior and verify the following: ¢ All plug-in connectors are firmly seated. © All integrated circuits on the game printed circuit board (PCB) are firmly seated in their sockets or soldered in place. ¢ No harness wires loose and/or disconnected. © No loose foreign objects present, especially metal ones that could cause electrical problems. Check the power supply (located on the floor of the game cabinet), the two speakers, the player controls (Trak-Balls™ and start/shoot/jump buttons) and the TV monitor for secure mounting.
TRAK BALLT™ ASSEMBLY (RIGHT PLAYER)
STARTISHOOT/JUMP BUTTON
COIN DOOR
Figure 1-1 Control Panel and Player Controls
1-2 Basketball™
c. installation requirements
This game is shipped for operation at 110 VAC, 50/60 Hz. However, the power supply has four voltage-selection plugs that allow for the use of four different voltage ranges. Therefore, if your line voltage is 220 VAC, plug in the red plug. (See Figure 1-2)
- Low Voltage Problems If your game is set for 110 VAC (or 220 VAC) and your line voltage is usually below 100 VAC (or 200 VAC), you may experience a decrease in the size of the monitor picture and/or the game operation will be erratic (weird things will appear on the screen}.
- High Voltage Problems If your game is set for 95 VAC (or 210 VAC) and your line voltage is usually above 110 VAC (220 VAC), the monitor picture size will increase, the game will run hotter, and the game will be prone to an increase in the rate of failures.
LINE VOLTAGE-SELECTION VOLTAGE PLUGS-WIRE COLOR
95 VAC. BLACK 110 VAC ORANGE {installed at factor 210 VAC GREEN
VOLTAGE SELECTION PLUGS POWER-SUPPLY CHASSIS
ON/OFF AND INTERLOCK SWITCH
Figure 1-2 Voltage Selection Plugs
Basketball™ 1-3
H BE SURE THAT THE POWER SUPPLY VOLTAGE d. interlock and power on/off fF RR mien switches (See section C of this chapter).
- Purpose of Interlock Switches. Two interlock switches have been installed on your game to minimize the hazard of electric shock while you are working inside the cabinet (see Figure 1-3). One switch is located behind (inside) the rear access panel and the other behind the coin door. These switches remove all AC line power from the game circuitry whenever either door is opened.
Check for proper operation of the interlock switches by performing the following steps: . ¢ Unlock and remove the rear access panel and open the coin door. © Plug the AC line power cord into your wall outlet. Set the power on/off switch to the “on” position {see Figure 1-3). Close the access panel and coin door. The attraction lamp should light, and within 30 seconds, the TV monitor should display a picture. Slowly open either the coin door or the rear access panel, and watch the TV picture. It should go off, along with the attraction lamp, when either the door or panel is opened approximately one inch. If the results of this test are satisfactory, the interlock switches are operating properly. If they are not, check that the interlock switches are not broken from their mountings or stuck in the “on” position. Close and lock the rear access panel.
SWITCH
(PULL IN DIRECTION OF
REAR VIEW ARROW TO DEFEAT INTERLOCK) INTERLOCK SWITCHES (2)
FRONT VIEW
Figure 1-3 Power On/Off and Interlock Switches
1-4 Basketball™
e. self-test procedure
Your game will test itself and provide data to demonstrate that its circuitry and controls are working properly. This procedure uses the TV monitor and the speakers; no additional equipment is required. (See Figure 1-4 for location of the self-test switch.) To start the self-test procedure, slide the switch to its “on” position as shown in the figure. See Table 1-1 for further details and instructions on the self-test. We suggest that you run the test each time the coin box is emptied.
f. volume adjustment
The audio volume may be adjusted to suit your particular location and conditions. The volume control is located on the same printed circuit board as the self-test switch. See Figure 1-4.
VOLUME CONTROL
SELF-TEST SWITCH: SLIDE SWITCH DOWN FOR SELF-TEST
Figure 1-4 Volume Control and Self-Test Switch
Basketball™ 1-5
Table 1-1 Self-Test Procedure
ZERO PAGE RAM TEST
PLAYFIELD RAM TEST
ROM TEST
PATTERN TEST
SWITCH/TRAK BALL/ AUDIO TEST
1-6 Basketball™ Automatically advances to the next test.
Screen displays “RAM OK ROM OK” and advances to next test.
Automatically advances to next test (no screen or audio output).
The complete set of characters is displayed on the screen.
With all switches open, audio outputs @ continuously rising tone. Closing any switch (2 start, 2 coin, 1 slam) will stop tone output, start crowd noise output at low level. LED is “on” when switch open, “off? when closed. TRAK BALL™: Rectangles respond horizontally and vertically to Trak Ball™ movements, black rectangle to left ball, white rectangle to right ball. AUDIO: The audio tone heard when two rectangles are vertically aligned indicates “dribble” sound effects working properly. Low-pitched audio whistle; CRT will display “Z PAGE LOW NIB BAD” or “Z PAGE HIGH NIB BAD” followed by either the letter E or D. The letter indicates whether the faulty RAM chip is at D2 or E2.
Game will not respond if self-test switch is turned off. Audio whistle will be heard, and screen will display “RAM BAD” and one or more letters. See Table 1-2 for faulty chip isolation information.
Message from test #2 changes to read “RAM OK ROM BAD” followed by a single letter from A to P that tells you which ROM is bad. See Table 1-2.
One or more characters not displayed or improperly displayed.
No rising tone, no crowd noise, LEDs do not light.
Rectangles do not respond to Trak Balls™ or respond incorrectly as compared to description at ieft.
Table 1-2 Faulty Circuits or Chips
SELF-TEST ROUTINE: RAM TEST SELF-TEST ROUTINE: ROM TEST
MONITOR DISPLAYS: | FAULTY CIRCUIT OR | MONITOR DISPLAYS: FAULTY CIRCUIT OR CHIP LOCATED AT: CHIP LOCATED AT:
2kx4 | 4k x 8 PROMS | PROMS | ROMS
RAM BAD A ROM BAD A RAM BAD B ROM BAD B RAM BAD C ROM BAD C ROM BAD D RAM BAD E ROM BAD E RAM BAD F ROM BAD F RAM BAD G ROM BAD G ROM BAD H RAM BAD I ROM BAD I RAM BAD J ROM BAD J RAM BAD K ROM BAD K ROM BAD L RAM BAD M ROM BAD M RAM BAD N ROM BAD N RAM BAD O ROM BAD O ROM BAD P
Basketball™ 1-7
g- operator options
The operator options offer maximum player appeal for your game location(s). These options are listed in Table 1-3. They are preset for a certain game setup during production. To determine how the switches have been set for your game, compare the attract mode with the information in Table 1-3. Operator Option Settings.
To change the toggle positions of the switch assembly and set the desired options, you need not remove the game PCB (see Figure 1-5).
GAME PCB
Figure 1-5 Operator Option Switches
1-8 Basketball™ OPERATOR OPTION SWITCH SBBBEBER: Biysreer
Table 1-3 Operator Option Switch Settings
Toggle No. & Setting of DIP Switch on PCB Result of Setting
Free Pay —StCt«=*d Play 2:30/Credit* 2:00 Credit* 1:30/Credit* 1:15/Credit* 1:00/Credit* $ 0:45/Credit* 0:30/Credit*
Game Instruction Language English$ German Spanish French
Dollar Coin Mode** 1 Coin = 6 Credits 1 Coin = 5 Credits 1 Coin = 4 Credits 1 Coin = 1 Credit$
One or Two Coin Minimum One Coin Minimum$ Two Coin Minimum
- A “credit” is a block of time for one or two players. $ Indicates setting when game is shipped from Atari **For left coin mechanism only
Basketball™ 1-9
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
qn00P OO OS eg,
a. introduction
Your game has three basic modes of operation. These are called the Attract Mode, the Play Mode, and the Self- Test Mode. The attract mode is specifically programmed to attract potential players and to educate them in the techniques used to play the game successfully. The play mode is initiated when coins have been inserted and the start/ shoot/jump button pressed, and ends when the game is over and the attract mode is re-entered. The self-test mode was described in Chapter 1. Its only function is to allow you to check the various electronic circuits and controls included in the game.
Basketball™
b. the attract mode
The attract mode is entered after game power-up, when exiting from self-test mode, and after the end of a game. Basically, this mode has two functions. First, by displaying two “men” shooting, tossing the ball, and the like, it acts as an attractive inducement to potential players. Secondly, the attract mode display aids the first-time player in learning how the game is played. He can learn that longer shots are “made” by allowing the shooter’s arm to come up and back farther before releasing the ball by watching the graphics display during the attract mode. Short shots are released more quickly.
When sufficient coins have been deposited, the message PRESS START is also displayed. The message ADD COINS FOR MORE TIME is also displayed in the attract mode. This mode terminates upon pressing the start/ shoot/jump button (if sufficient coins have been deposited) or throwing the self-test switch to self-test mode.
c. play mode
Play mode is initiated when both start/shoot/jump buttons are depressed, provided that the required minimum number of coins has been accepted by the game. A short tune is played, and both men appear on the screen. The ball drops onto the court from above to begin play. The player who gets the ball attempts to dribble into shooting position. Sound effects of the ball being dribbled accompany the action. The Atari Trak Ball™ is used for directional and speed control of the men displayed on the screen. Shooting (man
2-2 Basketball™ with ball) and jumping to block shots (man without ball) are done with the start/shoot/jump buttons.
If the defensive player can maneuver his man into position directly in front of the man with the ball, the ball can be “stolen”. When the offensive player depresses his start/ shoot/jump button, his man brings back his arm before shooting. When the button is released, the shot is made. The longer the button is held down before release, the farther the ball travels when shot. Each time a basket is scored, the player who made the shot is awarded two points. The scoreboard is at the top of the display. At the end of the game, the unit plays its short tune once again. If additional coins are not deposited before the game timer reads “0:00”, the game returs to the attract mode, but the score continues to be shown.
If only one player is participating, he plays against the game’s computer. In this case, the play mode is initiated by pressing only one of the start/shoot/jump buttons. If the second button is not pressed within a few seconds, the game will initiate play as a single-player game. The computer becomes “tougher” as the player begins to run up a score on it. If the player gets eight points ahead, the computer controlled “man’” begins jumping to block shots. This provides a greater challenge to the player. In all other respects, the single-player game is the same as the two-player contest.
d. self-test mode
As mentioned, the self-test mode is for purposes of allowing the game to test itself without additional electronic or other equipment. See Chapter 1 for a complete description of this mode.
POWER-SUPPLY CHASSIS
ON/OFF AND INTERLOCK SWITCH
Slow-blow 2.5 Amp. 125 V. Slow-blow 8 Amp. 125 V. Fast-Blow
Figure 3-1 Game Fuses
b. cleaning
The exteriors of game cabinets and transparent plastic panels may be cleaned with any non-abrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor. Do NOT dry-wipe the acrylic plastic panels, because any dust can scratch the surface and result in a “foggy” appearance that will seriously detract from the game's player appeal. c. game fuses
The game contains a total of five fuses mounted in holders on the power supply chassis. These are accessible through the rear access panel. Replace fuses only with the same type and rating. See Figure 3-1 for location and rating of each fuse. Also see the manufacturer's manual for the TV monitor for fuse information on the monitor unit.
3-2 Basketball™ Ci TY
maintenance
and
adjustments Ss
a. introduction
Due to its solid-state circuitry, this Atari game should require very little maintenance and only occasional adjustment. Information given in this chapter is intended to cover most servicing situations that may be encountered at the game site. The procedures described are sufficiently detailed to make them easily understandable by persons with only moderate background or technical training.
Basketball™
d. player contro! panel
To reach the two start/shoot/jump LED switches and the Trak Ball™ assemblies, the player control panel must first be hinged open as shown in Figure 3-2. Follow this procedure: *¢ Remove the three Allen-head capscrews from the top of the control panel. © Gently lift the back edge of the control pane! upward and away from the game. This will reveal the two Trak Ball™ assemblies and the LED start/shoot/jump buttons.
- LED Start/Shoot/Jump Switches The LED pushbutton switches on the front edge of the control panel have a very low failure rate, and if a malfunction is suspected, they should be tested before replacement. To test the LED switches, proceed as follows: *¢ Remove the wires from the suspected switch. © Set the multimeter to the ohms scale.
- Set the meter to the R x 1 position and “zero” it.
- Connect the meter leads to the appropriate switch contacts. (See Figure 3-3.) © Check contacts by pushing and releasing the switch button for a very low resistance reading when closed and a very high reading when the switch is released (open).
- If the contacts do not operate “sharply” or if they always stay open or closed, replace the switch as described in Figure 3-3.
- Trak Bali™ Assemblies The two Atari Trak Ball assemblies with their associated printed circuit boards (two per assembly) are reached by opening the player control panel. To remove a Trak Ball assembly, disconnect steering PCB connectors and remove three assembly retaining screws; see Figure 3-4.
- REMOVE THE THREE FLAT HEAD CAPSCREWS FLAT HEAD CAPSCREW
CONTROL PANEL
HINGE
- HINGE THE CONTROL PANEL FORWARD AS SHOWN BY ARROW
Figure 3-2 Hinging the Control Panel Open
Basketball™ 3-3
NORMALLY CLOSED (N.C.) CONTACTS
TURN COUNTERCLOCKWISE TO REMOVE
LIGHT-EMITTING DIODE (L-E.D.) CONTACTS
NORMALLY OPEN (N.0.) CONTACTS, DOUBLE-POLE SINGLE-THROW (DPST) SWITCH WITH INTERNAL LED
- Remove ail wires from the suspected switch.
- Turn the switch counterclockwise while holding the cone- shaped nut on the outside of the game cabinet. Install a new switch using the reverse procedure. Reconnect the harness wires.
Figure 3-3 LED Start Switch Testing and Replacement
CONTROL PANEL SHOWN HINGED OPEN
3-4 Basketball™ —-—~=»
PCB RETAINING SCREWS
ASSEMBLY RETAINING SCREWS (3)
Figure 3-4 Trak-Ball™ Assembly Removal STEERING PCB
4¥%2” DIAMETER BALL
CONTROL PANEL
BALL COVER SCREWS
e. loudspeakers
The only probable cause of failure of either of the two loudspeakers is an electrical short or a ruptured cone (both highly unlikely). The speakers are located directly below the monitor shelf, and may be reached through the rear access pane! of the game.
f. fluorescent lamp
To replace the fluorescent lamp, proceed as follows: ¢ Remove the hex socket cap screws (there are three) from the top of the game.
«Lift off the top attraction panel retainer strip, being careful not to let the panel fall forward from the game. ¢ From the front of the game, lift the panel upward and away from the game. ¢ With the panel removed, the 24” fluorescent tube can be replaced in the normal manner. © Replacement of the panel is the opposite of the above steps.
g. tv monitor removal
The TV monitor may need to be removed for service. This is done through the front of the game as shown in Figure 3-5. Proceed as follows.
Hazardous or startling high voltage potential exists in any TV device, even with power disconnected. Use extreme care not to contact electrical parts on the chassis with the hands or metal objects held in the hands!!!
Unplug the game from the wall plug. Unlock and remove the rear access panel. Remove the attraction panel as described in section F of this chapter. Lift out the cardboard bezel from its position in front of the monitor.
Remove the four woodscrews and the two corner securing brackets. From the rear of the cabinet, remove the two wing nuts and two hex nuts, four lock washers and four flat washers from the carriage bolts that secure the TV monitor to its supporting shelf.
Unplug the TV monitor connector from the back of the monitor.
Remove the mounting bolts, and slide the monitor off of its shelf and out through thi front of the game cabinet.
After service/repairs, replace the monitor by reversing the above steps. Note that the wing nuts go on the front two bolts, and the hex nats on the rear bolts.
RETAINING STRIP BOLTS
TV MONITOR SHELF
CARRIAGE BOLT (4)
FLAT
ra HEX NUT (2)
WING NUT (2) UPPER ATTRACTION PANEL RETAINING STRIP
TV MONITOR
CORNER SECURING BRACKET(2) WOOD SCREWS (4)
CARDBOARD BEZEL
ATTRACTION PANEL
Figure 3-5 Removing the TV Monitor
Basketbal™ 3-5
h. game printed circuit board
You may wish to remove the game’s printed circuit board (PCB) for service or inspection. To do this, proceed as follows:
- Switch the game power off and open the rear access door. © Locate the screw that secures the game PCB in its slots (see Figure 3-6) and remove it.
- Carefully slide the PCB out of its slots, and unplug the edge connector. Be careful not to twist the board, as this may loosen connections or components. © Perform the maintenance, etc. as required. ¢ Replace the PCB, making sure that the edge connector is properly plugged in. Note it is keyed to fit in only one position, so if it doesn’t slip on easily, don’t force it! e Replace the securing screw through the hole in the PCB. © Close and lock the rear access panel. e Turn the power switch on and check that the operation of the game is correct (by playing the game).
Figure 3-6 Removing the Game PCB
3-6 Basketball™ SECURING SCREW UY Nn OT ASTN
aA «
nv
GAME PCB “0 ys
OPERATOR OPTION SWITCH HEBER
details of electronic
operation oe
a. general information
This chapter provides a general overview of the operation of the game printed circuit board (PCB) electronics. It also goes into specific detail of the various circuits to explain to an individual of moderate technical background how these circuits should perform. This information has been organized with emphasis placed on troubleshooting the game PCB, circuit by circuit.
Figure 4-1 illustrates the major components, including all controls remote to the game PCB. The function and direction of signals to and from these various controls is also shown.
The PCB block diagram in Figure 4-2 illustrates the division and function of the various circuits located on the game PCB and how they are controlled by the microprocessor. Refer to Figure 4-2 as you go through the following circuit descriptions.
The functional operation of the game PCB begins with the microprocessor (or MPU) circuitry. As you read the various circuit descriptions, you will learn how the MPU receives its sequential program instructions from ROM memory and how it carries out these instructions through the use of RAM memory (Section C); how it reads in the game switches (Section H); outputs its instructions and calculations to the other PCB circuitry such as the playfield generator (Section E), the motion object generator (Section F), and the audio generator/mixer (Section I).
A description of the standard Atari sync generator (Section D) is also included. This is the only PCB circuitry that functions independently of microprocessor control. Basketball™
TV MONITOR TO ~ HORIZONTAL DEFLECTION | INTERLOCK ‘SWITCH MONITOR CONTROL ‘ciRcUITRY
p-% ss | nore oie pes)
STARTISHOOT/ JUMP BUTTON
TRAK BALL CONTROL GAME
PRINTED CIRCUIT BOARD (PCB) STARTISHOOT/ JUMP BUTTON AuDIO AMPLIFIER PCB SPEAKER
AUDIO VOLUME
TRAK BALL CONTROL SELF-TEST ‘SWITCH
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING. CONFIDENTIAL” Reproduction. forbidden without the Specific written permission of Alan, Ine,” Sunnyvale, lifornia. This drawing is only conditionally issued, and. neither receipt nor possession any right in, or license to use, the subject matter of the ‘drawing or any design or technical information shown thereon, nor any ght fo aproduce ths drawing or any pat thereof, except for manufacture by vendors of Ata, incor Porated and for manufacture under the corporation's wil: ten license, no right to reproduce this drawing is granted Or the subject malter thereat uniess by written agreement with or writen permission from the corporation, reot confers or transt
Figure 4-1 Game Block Diagram
4-2 Basketball™
Basketball™ 4.3 ete raton a tooeat oor
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING
Figure 4-2. Game PCB Block Diagram
4-4 Basketball™ ney
Veo RET
- (zsaves} Ste Os0K0K-o1
(Cenvaarend= rr ra & rsa & lot of ot of oofox lot ot of gt op es
sie le ot ob gotex |
rows pve
rR. 4 =——* won le poner of SES wee © Suan t craw
nuo1e BOARD ‘Sunnyvale,
issued, and
S
joo Pegur view Ge caver Figure 4-3 Game Wiring Diagram 034540-01A.
b. power supply
The power supply provides all necessary game power as shown in Figure 4-3.
The game PCB receives an unregulated + 10 volts DC at pins B and 2 of the PCB edge connector. The +10 volts DC is rectified and filtered in the power supply assembly and regulated to a stable +5 volts DC by the LM323 on the game PCB. The regulated +5 volts DC is distributed throughout the PCB to power all logic circuits (see Figure 4-4).
The unregulated +10 volts DC also powers the LM324 audio amplifier circuits in the audio circuitry.
stam swerren
15 pos MOLEX
Coin Door Puc + MALE TERMINALS,
fom
ers ¥ |, ze0v oWitea een
dy | me || [vise 2080 rt
Power Supply
sy out Power TO Pcs At GAs to Wiptalcoabat>
oe le L fe if | esi NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL’ Reprosuction forbidden without the Specitic walton permission ol Atari, Inc. Sunnyvale, ry — Giiomie" ths acawing ts only conditionaiy issued, and
| | | eh» | 7 | heer eeelnay possnasion mereot contre or rantars |
| z | 7 | ny Tight in oF icense to use, the ubiect matter of | Ihe |
| FH\, | 3) || | ee | drawing. or any design of technica information, shown |
ef thereon, nor any right fo eproduce ils orauing.orany pat
| 7 | ~ | Stow | | | 2 | Iheveor | except fof manutactore by wondors of Aart, neor |
| en_[2| len | Tt] Seva| 4 | porated and for manufacture under the corporation's wri |
‘yn wae |) {en license. no fight 19 reproduce this drawing is granted
| ec | [Clee | Lj} | 8s | rine subject matte: thereorunfoss by writen agreement |
| i | t | on | fe | wth or wiltten permission rom the corporation, |
Figure 4-3 (Continued)
Basketball™ 4-5
2a! cat
siov ores [B[2}~
ew | tow
Te, GND CROWS 2,8,9) €1-8,10-20,22-417 43/82,62,63 fz ]-1 BxPASS NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the speciic. wil mission of ‘Alar, ine. Sunnyvale, ly conditionally issued, and reo! canter or ranslers is, the subject mater of (he formation snown nto reproduc this Grawing or ary pa except for manufacture by vendors of Alar, meor ther porated and for manufacture under the corporation's wit ten. Fight to reproduce this drawing Is granted ort ‘aller thereo! uniess by written agreement ‘with or wetten permission trom the corporation,
Figure 4-4 Game PCB Power Distribution (Part of Game PCB 034268-XX A)
c. microcomputer circuitry
The heart of the game PCB is the microcomputer circuitry. A brief description of the major components and their functions is provided in the following paragraphs. Note that the microprocessor components include the following:
- MPU at location C3, address buffers at B2 and C2, and data buffers at E3 and E5 (See Figure 4-5)
- ROM memory at locations B1, C/D1, D/E1, and F1 for the -02 version, or PROM memory at F2, H1, H2, Jl, J2, K1, K2, L1, L2, M1, M2, N1, N2, P1, P2, and R11 for the -01 version (See Figure 4-6)
- RAM memory F3, F5, H3, H5, K3, K5, L3, and L5 (See Figure 4-7)
- Address decoding circuitry C4, M6, M7 and associated gates (See Figure 4-8)
- Watchdog reset counter C5 and associated circuitry (See Figure 4-4)
MPU, ROM, and RAM (See Figures 4-4, 4-5 and 4-6)
The microprocessor is the “master controller” of all action that takes place in the game circuitry. Upon initialization, the MPU (via ABUSO thru ABUS15) addresses data locations in the program ROMs or PROMs. The data in the addressed locations then travels to the MPU via the 8-bit data bus (DO thru D7). The MPU decodes this data to determine what action it is to perform next (i-e., “read coin switch 1,” “JUMP”,
4-6 Basketball™ etc.). The MPU uses RAM memory to temporarily store information which it will later recall. The MPU is capable of writing (or putting data into) the RAM and then later reading (pulling data out of the RAM, via address bus (ABUSO thhu ABUS15) and bi-directional data bus (DO thru D7).
Address Decoding (See Figure 4-7)
The MPU address decoding circuitry performs the critical function of turning on or enabling the appropriate game circuitry (i-e., RAM, ROM, latches, etc.) at the correct time, so that information can be transferred back and forth between the game circuitry and the MPU. Table 4-1 is the memory map for this game.
© 0 Clock Driver
(See Figure 4-5)
The basic operating frequency of the microprocessor is established by its @ O input (on pin 37 of the MPU). The MPU runs at an operating frequency of 750kHz. Examination of the MPU 2 output waveform (pin 39) with an oscilloscope should show a signal with a period of 1.33 microseconds. (The period of any periodic waveform is the measurement of the time it takes to complete one full cycle.) The 750kHz clock outputs are generated by the 4H signal. This 4H frequency is generated by the horizontal sync counter R4 to produce the @ 0 clock input. (See Figure 4-8, 0 Clock Driver Signal.)
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING. CONFIDENTIAL: Flepraduction forbidden without the ‘Specific written permission of Atan, Inc, Sunnyvale GGivfornia’ This deawing Is only conditionally issued, either receipt nor possession tnereat confers or transfers {ny fightin, oF license To "se, the subject matter of the Srawing of any design or technical information shown ‘thereon, nor any right fo reproduce this drawing or any part thereat, except for manulacture by vendors of Ata, Incor: fated and for manutasture under the corporation's writ. Mn llgense, no right te vebroduce this drawing is granted forthe subject matter ‘hereof unless by witten agreement ‘with or written permission trom tne corporation, aay
ass
nae
ns anu
22e asi0
a9]
©3 sal 90-6010 (@502) an) Agus aps] ABuse
ABuss.
en Anus4 THER RESET. ABUSS, v8, 4K Apuse
aust Riag DISABLE T
7. bev sys!
o 4d Dev sys ars.
Figure 4-5 MPU Circuit Schematic Diagram (Part of Game PCB 034268-XX A)
Basketball™ 4-7
| #SV | 45v | 4ev | 45v | 45Y | 45V | sev | 5M | 45Y | 4EV | HEY | 4S | HSV 4SV | 45v | 4By |
ree Toe
jcca [cea leer leer leer eee
Toa
MT one
-01 VERSION (PROM)
away ag
| la | te 1» | bets | rola | foe |
| ws | fees — | ees | = |
81 rs fey, | es osttes fosttes | osties | ost tes so is ral : SR
. 8 fa nt BS eT Hr DBUST
| be | He | 6 |
| Ds | = | s |
| ba | = | 4 |
| bal | [3 | 3 |
| D2 | a | 2 |
| Dt | is | 7 |
- DBUSO est oa eres [en glow ge Be Wie Sila roms, =
~O2_VERSION (ROM)
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: ‘Reproduction’ forbidden without the Specific written permission of Alar, Inc... Sunnyvale, California’ This crawing 1 only conditionally issued, and neither receiptnor possession thereof confers or transfers, any right in, oF license to use, the subject matter of the frawing of ‘any design or techaical information. shown thereon, nor any ght Yo roproduce his Grawing or any pat ‘hereof, excep! tor manufacture by vendors of Alar, Incor: pporated and for manufacture under the corporation's wit. fen license, o sight to reproduce Inis drawing is granted for the subject mailer thereol unless by written agreement ‘with or whitten permission irom the corporation.
Figure 4-6 ROM Memory Schematic Diagram (Part of Game PCB 034268-XX A)
4-8 Basketball™
NOTICE TO ALL PERSONS RECEIVING THis DRAWING CONFIDENTIAL: Reproduction, forbidden without the specific written permission of Alar. Inc... Sunnyvale, California. This drawing 's only conditionally issued, and neither receipt nor possession thereol conters or transfers any ‘ight in, oF license to use, the subject matter of tne Grawing 0° any design or technica! information shown 398, Nor any rigntto reproduce ihis Grawing oF any part ‘except tor manufacture by vendors of Atari incor porated and for manutacture under tNe corporalior fon conse, no ght to reproduce ths Urawing ‘or the subject matter thereot unless by written a with or written permiseion from the corporation.
Figure 4-7 RAM Memory Schematic Diagram (Part of Game PCB 034268-XX A)
sors bores Ee TIMERRESET
Leo ours.
Apuss awuse, agus! Leo
anuse NOTICE TO ALL PERSONS RECEIVING THIS ORAWING: CONFIDENTIAL: Repraduction.forpieden without The specie watten, pemission Alar Ine,” sunnral California’ This orawing 18 only conditionally iss oN oitner receipt nor possession thereol confer oF JcOuNTER, ‘any right in, oF Henge To use, the subject matter of the Srawing of any design or technical information. shown {erean, nor any ight to reproduce this drawing or any part Ineteot ‘except fof manutacture by vendors Atari incor porated and for manvlacture under the corporation's wil. tenicense, no ight lo reproduce ths drawing 's granted oF the sunjéc\ matter thereol Uniess by written agreement with or wetten permission fom the corporation.
Figure 4-8 Address Decoding Schematic Diagram (Part of Game PCB 034268-XX A)
Basketball™ 4-9
ALHOMd LSAHOIH SWH D4 ALOTd 1S3M01 SWH OO
0 + XXaT +40 SLSISNOD YOOTE HOVa OSAd HOTOO = £ + XXAT SUNLOIa Od TVLNOZIMOH = 2+ XX#t SOd TWOUYIA = T + XXET
ASOT = JE + OOOT
SALAG b JO SHOOT 9T
NOLLVZINVOHO Wd NOLLOW
Ads€-0002 SSOT-008T got azor zor veot 8201 9z01 v201 zzor QLOT ort oot £080 2080 2080 0080 0080 0080 0080 0080 0080 0080 4400-0000 DEP HE KDC OE 26 DKK OK DE DE HE 2 OK DK OK DE OK 9 DE OK DE OE OS DO DE DE I DE KK OK DC 36 DE 3G OK OK Dd DE 9 DK OK DE HE DE DE DE DE IDK OE OK DE De 9g DE 9 Hosco oo coc oso So SCO SCO OOD OOOO COD OZOOC0C Dede ner OSDCOSCOCOC SOOO ODOC OCOOO PH OOD ODO COC OCH Ree ee DD E26 6K HD DE DE DEK OK OE DK DE DE DE KK DK DE OK DE DE OK 9E DE DE IK OC DE OK DD HH HK DE HE OS DEK 2 DE KE OEE OE DE HK DE OE DK DE OE OO 9 DE DD HH 6 EK KK DEE DEK OC DK HK DE DE OE LD DE OK EK DK DE OG DE OK DDH HK HK DE DG HE DK HE OE DC 2G OE DE KK DK DE DE OE EO DE DE DK DE IK OSD DD 2 HK DE DE OE 96 EK HK OK OK DE DE DE 3S DE OE EK OK DE DE OE 9 EO OE OE DKA EOC KKK KKK KK KK KK KK > > PPR ODSOO COM HO KKH HH KK KO EK DDK ESO 0 DE HK OK OE HE HE EEK OK OE OE DE OE 3 OE DE KKK DDO OO KK DE DE EE DE EOE KOE OE OE EE DED PPK HOM OM OE KKK HH EEE EHH OOD ODO CO OOO> >> KO DODUTOXX XH SOD SSC OOOO ODOC CO OOOD WX ESESSSS SESS DW AW ATW WDAWADDAADBWR COOK KK KK KK OK MK KOK MRK KOK OKO DOOX MH KK RK KK MOK KKK KOK KKK MK KOK KOKOO OOK KKK MK KKK OK KM KOK KKK KOR KKOXOO DOOR KKM KOK KOK KM MOK MMM KOKKRKOXTO DOO KKM KKK KOK OK KO KK KK KOK MH KO KOKO DOUK KKK KK TKO KKK KKH KKM KKK KOKOMO DOOXK RK KK OKOKXOKHKXKKO MRK KKOXOXT HK EE OK OE EO KO KO 1da7 YLNO NIOD. ASAL 0 NIOO. TNIOD ZNIOD T Luvis 01 201 8 Ta) WvH9OUd AWVS } a SION 29S - WYY CTSIAV Id
AONNO dv amox 1384 WaWlL
S1dO aWV9 MS did
YNVTSA wvis ALS LSAL oud (01 201 8 Id} TUG (07 201 8 TaD) 2d (01 207 8 1d) eud (01 207 8 Ta) Wve ONDRIOM LYSA @ YATd (TH 207 OT TdT) auvdS (01 Za1 8 1a) ZHOH Z WATd (TH 207 ‘01 17) USAC ZLON iD OISAW | a @ LUVLS (01 2018 1d) LY3A T HAT (TH 207 8 Tot ZHOH I ATd (TH 201 8 TOD)
will@Q24SeG = OT-p ov sv ov iv] sv 6v OV LIV]zIV ev bIV SIV | IvWIOJdVxXaH Ed & m/a [ov dep Muomay god weg T- a19eL Iq 2d fa ba sa 9a La g NOWONN
Watchdog RESET (See Figure 4-4)
The reset counter in the microprocessor control circuitry is a 4-bit decade counter, C5. The Qp output of this counter is the RESET signal to the MPU. Counter C5 counts how many times the 128V signal changes states. On every highto-low transistion of 128V, the counter advances to the next count in its sequence. Meanwhile, the TIMER RESET signal, generated by the MPU at various times during its normal instruction sequence, is resetting the counter back to zero. If for some reason, the MPU program has strayed from its intended instruction sequence and the TIMER RESET signal does not occur before this counter counts up to a point where the Qp output goes high, a RESET signal is generated to the MPU. The RESET signal causes the MPU to restart its instruction sequence from the beginning of the program.
d. sync generator
(See Figure 4-9)
The basic frequency of the sync generator is a 12.096MHz clock, generated by a crystal-controlled oscillator consisting of crystal Y1, inverter R3 and several descrete components. The output of the oscillator is 12MHz. Examination of this signal with an oscilloscope (at pin 4 of R3) should show a period (or one cycle) of approximately 83 nanoseconds (.083 microseconds).
This base frequency is then divided down by binary counters R4, P4, and N4. These provide the various horizontal synchronization frequencies (1H thru 256H). The final output of this horizontal counter chain is 256H (at pin 13 of N4). This signal is, in effect, a division of the base frequency by 768, or 15,750 Hz. The period of 256H is about 63.5 microseconds (15,750 Hz). The 256H signal, as well as other horizontal signals, are used to generate the H BLANK and H SYNC timing pulses at flip-flop P5. See Figure 4-9, Horizontal Sync Timing Diagram for the relative timing of these waveforms.
The H SYNC signal is used to clock two stages of vertical sync counters P6 and N6. The H SYNC signal is divided down by these counters to form the various vertical synchrozintation frequencies (1V thru 128V). These two stages are used, in effect, to do a divide by 262 of the H SYNC signal. This results in the final output of these counters (128V at pin 11 of N6) of 60 Hz (the period is approximately 16.6 milliseconds). The various vertical frequencies address a sync PROM (N5) whose data is latched at the output of P7. The outputs of this latch are the various polarities and phases of the vertical timing frequencies used to synchronize the TV monitor display. See Figure 4-9, Vertical Sync Timing Diagram, for the relative timing of these waveforms.
The end result of the horizontal and vertical timing waveforms is to synchronize the TV monitor display. This display consists of 262 horizontal lines per frame, with each line being the time equivalent of 768 (12MH2z) clock pulses. Each frame is repeated 60 times per second providing the necessary frequency of display refresh to provide a stable, non-flickering display.
a. playfield generator
(See Figure 4-10)
The Piayfield generator generates the playfield video. The video is actually generated by the data stored in the graphics ROM comprised of ROM devices A/B6 and C6. (See Figure 4-13). This ROM video information is addressed by data obtained from the playfield display RAM.
The alpha and numerics and the basketball court picture components that make up the playfield picture are displayed as 8 line by 8 bit blocks of video on the TV monitor screen. The microprocessor loads the playfield location bits into the RAM. The RAM outputs (PFDO thru PFD31) are then multiplexed through data selectors/ multiplexers F4, H4, J4, and K4 and temporarily latched at the outputs of latches F6 and F7 at the rising edge of 4H. clock. The latched data bits then address the graphics ROM A/B6 for one of 64 different pictures stored in it. The vertical signals (1V, 2V, 4V) determine which of 8 lines of the character is currently being addressed.
The order of the picture data from the graphics ROM is selected by the picture reflect signal (PIC7) input to data selector/multiplexers A8 and B8. The picture data output is serialized by shift/register A9.
The method by which the MPU writes the appropriate playfield data to each RAM location and then the horizontal and vertical timing signals read this data out for actual video generation is knows as “cycle sharing”. The circuitry that controls this cycle sharing technique selects one of 3 sets of addressing information to address the display RAM.
Basketball™ 4-11
PRS RS BRE o d
| R | iia | [Pom ra pare | so Pi PPS PE | [Pe trex ese | ||||||
| 230 | 330 | cer | Ucer | a | eer | ag | ||||
| a3 | ail | RS | RB | ‘her asie | rf | cet ga | TC] | Sker | adie | Te = |
| 5 | ih | {So | ant | 2lep counter | 2tep couNTER | alee couwrer | | | |||
| Oe | ba | 306 | Soe | 2 a) 02.03 MR | 001 a7 3 ue | i 02.03.94 wR] | ||||
| bar) | | Bee | is fe pe pepe | 13 eye |
os | BRS. Rs okt me eMHa- 2 __tMnE i eo
| era | Bsa: | 3 | Re | |
| gras | eens | au | 1a | aig |
5 ae an 40 — a 3 Tot “ Re an — So Re {08 256H e ‘See | _sscq
* $ ean—4o J af HELENE aM ew WBLANK
sync —.
L-nevane
nos, PT
| eesitay | wns | |, |
yeuaue Bhan SYNC, al P/F of veuane veev —Haw ig VeXaN eev Yas 3 pos) aev— Fino nF bi av—the = ln a av—tae 8 se ie Bap
Lene —— >
| <Thth | | sad | RD |
= _Is je js lo do - 7 PES HE P ne ier sae Te 2\cp COUNTER NOTICE TO ALL PERSONS RECEIVING THiS DRAWING Bs.01 92 23 MR CONFIDENTIAL’ Reproduction foraaden without the rete Specite. waitten,permssion a! ‘tari, inc. Sunnyvat,
~w aw ey ww av ev nev Caliiorria’ This sawing is only conditionally 'ssued, and ‘either receipt noi possestion tnereol coniers or Wanofers {any fight in, oF license to use, the subject matter ef the Grawing oF any design or (echnical information shown thereon, nor ay, ight to reproduce this drawing 9 any part tmergolexcept Yor manulacture by vendors of Ae, Incor porated snd for manutacture under the corporation's wit {en license, no eight to reproduce ths drawing is granted ‘or the subject maltes thereot uniess ty written agreerient with'o# weitten permission from the corporation.
LI]
ane
vase
roma
vere
Figure 4-9 Sync Generator Schematic Diagram (Part of Game PCB 034268-XX A)
4-12 Basketball™
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
4-14 Basketball™ +sv- \___/ (sseiste)
mm TP Figure 4-10 (Continued) -O1 VERSION | a7 A o3at60 GProvine|
-02 VERSION
ce ie eno -2 ae ao — 22 “9 pave — Ae Are (saoie@) he
This circuitry functions as follows:
- When 4H is low, the MPU address bus (ABUS2 thru ABUSS) addresses various playfield display RAM locations, and writes appropriate playfield picture codes into them via the MPU data bus (DBUSO thru DBUS7).
- When 4H and 256H is low, the vertical sync signals (8V, 16V, 32V, 64V, 128V) and the horizontal sync signals (32H, 64H, 128H) address the playfield RAM through buffers N3.
pier —
20m ovas. L bas Ls DAS Ir eons. soaz + nal @oae—}-¢
iH = aie alt Ba She a Stan cs io}, vets a 6
| r | uly, | x} |
sa para ee af Hey 3
| | | | | | oF | de |
nae + voly tsIee pes, pi ufE sures H —
| coed | | | a8 | | |
| apes. | i | ls |
oft Mal
| ‘| | I | alia | "| | rc | SKB |
oe rab Si24 pe 1 Sis spe secss7,, epse—t ee BK, | hia pectic written permission of i is craving
| ‘seus | So | . |
maten- 2138 Jignl to reproduce nis drawing or any par except lor manulaciure by vendors of Alar, near erated ans lor manstacture ynas the corparatton's wi fen tioense, no rit to reproduce this grawing is granted or the subject mater thereat Uniess by wien agreement with or wrllien permission trom the corporation
Figure 4-10 (Continued)
Basketball™ 4-15
The data is read out of the RAM by the horizontal and vertical sync signals, and the appropriate byte of the 32-bit PFD word is selected by data selectors/ multiplexers F4, H4, K4, and L4. The picture codes (PFO thru PF7) always correspond to the portion of the monitor display currently being scanned. These picture codes address one of sixty-four 8 x 8 pictures stored in graphics ROMs A/B6. The output of the ROM is then converted to serial video (MASKA) information by shift register B8 and gated into the logical video mixer to generate composite video.
f. motion object generator
(See Figure 4-10 and 4-11)
For each motion object to be displayed, the MPU writes four bytes of data into the playfield display RAM. As with the playfield generator circuitry, when 4H is low, the MPU address bus (ABUS2 thru ABUS9) addresses specific RAM. locations and appropriate motion object codes are written into them via the MPU data bus (DBUSO thru DBUS7). The four bytes of data stored for each motion object are: 1) the vertical position of the object, 2) the type of object it is, 3) the horizontal position of the object, and 4) the “color” of the object. These four pieces of information are then accessed by the motion object generator as follows:
- During the horizontal blanking period before each scan line, the vertical sync count is compared to the vertical position of each motion object stored in the RAM, This is done by adders H6 and J6 which compare vertical sync with PFD8 thru PFD15. If a motion object is to be displayed on that scan line, a MATCH signal is generated at E9 pin 8, after a delay of one 4H clock pulse.
- Graphics ROMs address GAS through GA8 is latched at the output of flip-flop F6 along with the MATCH signal. This part of the address byte defines the motion object to be output from the graphic ROMs. The actual line of the motion object to be scanned is latched at the output of flip-flop H7 (GAO. through GA4). The MATCH pulse enables data selector/multiplexers A8, B8, C8, and D8 to pass sixteen bits of video data from graphics ROMs A/B6 and C6 to the inputs of shift registers A9 and E8. When the VIDLD pulse occurs, the graphics ROMs’ data output is loaded into the shift registers.
- The third byte of RAM data determines the horizontal position of the motion object. This RAM data (PFD16 thru PFD23) is latched by K6 and loaded into horizontal position counters L6 and K7. The horizontal location address generated by these counters then addresses high-speed VIDEO RAMs J8 and K8. These RAMs are now loaded with the video data for the particular motion object from shift registers A9 and E8 (which were loaded from the graphics ROM in the previous step).
- The fourth byte of RAM data for each motion object determines the various shades of color in which that object is to be displayed. This data (PFD24 thru PFD29) is latched by L8 and M8 and used to determine the combination of video data loaded into the high-speed video RAMs (in the previous step).
In review, all four of the previous steps occur during the HBLANK period preceeding each horizontal scan line. The proper motion object picture, with the proper “color shading” was loaded into the high-speed VIDEO RAMs. The horizontal and vertical location of the motion object has been determined by the portion of this RAM into which it was loaded. The motion object is now ready to be displayed on the TV monitor. When HBLANK ends, L6 and K7 are reset and allowed to sequentially count up to their maximum count. The outputs of these counters address the high-speed video RAMs (J8 and K8). When the RAM address encounters stored video information, the motion object video is output as GRYLVLO and GRYLVL1 and sent to the video summing circuit. The combination of these two “grey level codes” determine the shape and color of the different motion objects seen on the TV monitor.
4-16 Basketball™ en08P0O PCC,
Shue
ores
Maska—— masKs——
abHee in a aan B afer oh + Stes erpe wn 1a 3], te | "| prot. sp 3a rt sere
| Pree. | aM Jap, 218, aa} | £1 seq LSISS| | |
| Prpas. | tho Pr eat® | al, cs DATA | |
| erp27 | fan | aol | Placa MOL, |
| proas: | £}3 | mt |
ce fe. i aseuee
omer
NOTICE TO ALL PERSONS RECEWING THIS DRAWING. CONFIDENTIAL: Reproduction” fomidgen witnow ine specie written permission of Alar, Inc., Sunnyvale Ealvori, Ths arawing is nly condtinely issued, an neither receipt no: possession thereo! corvers or iransiers any sight in, or license to use, the subject matter of tno drawing of any design or technical Information. shown thereon. nor ans right ta reproduce inis drawing oF any part tnereot excent Tor manlacture'by vencors of Atari, Incr poiated and tor manulactwe under tne cerporaticn’s wri. fon icense, 00 right to reproduce this drawing is granted oF the subject matter thereat unless sy written agreement ‘with grwritten permission trom tne corporation.
Figure 4-11 Motion Object Generator Schematic Diagram (Part of Game PCB 034268-XX A)
Basketball™ 4-17
g. video summing circuit
(See Figure 4-12)
The video summing circuit receives MASKA from the playfield generator and GRLYVLO and GRYLVL1 from the motion object generator. These three signals are summed through various gates into flip-flop P10. The actual video to be displayed on the TV monitor is determined by the combination of the two signal outputs of this flip-flop. These outputs (P10, pin 5 and P10, pin 9) are mixed with composite sync COMPSYNC for a composite VIDEO OUT signal.
1, vidto out
Re cr Z] vine out we
a aur me | Ws 19 326 CAYLEE sm ale fas came ‘a
ry 180, 1 tj vineo ner uth
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproduction forbidden wheal the wltien permission of ‘Aart: ine, "Sunmyvae, ia This cravings Only conanionaly issued. and ecetpl nor possession lnereot ortransters, ny right in-or hegnae to uae, ine Subject matter of he Grawing of any design or technical information shown thereon, nor an ght {0 reproduce ths rawng any part thereot excegt for manulacture by vendors olAlari, Inco!” porated and for manufacture under tne corporation's wit {en license. no right to reproduce this drawing is granted or the subjéct matter thereat unless by written agrwement ‘with of written permission fom ine corporation.
Figure 4-12 Video Output Schematic Diagram (Part of Game PCB 034268-XX A)
4-18 Basketball™
hb. trak ball control and switch
input circuitry
(See Figure 4-13)
Both the left and right player START/SHOOT/JUMP switches and the left and right Trak Ball horizontal rate of turn information are read by the microprocessor on data lines DBUSO thru DBUS3. The left and right Trak Ball vertical rate of turn information and vertical and horizontal direction of both Trak Balls are read by the MPU on data lines DBUS4 thru DBUS7.
Signals from the address decoder determine which signals are read by the MPU. When LD1 and LD2 are both low, the MPU reads both the player START/JUMP/ SHOOT switches and the horizontal and vertical direction of turn of both Trak Balls. When LD1 is low and LD2 is high, the MPU reads the left and right Trak Ball horizontal rate from counters J9 and J10. When LD1 and LD2 are both high, the MPU reads the left and right Trak Ball vertical rate from counters H9 and H10.
The two coin switches, the TEST switch, the TEST STEP switch (used only during manufacturing), the SLAM switch and VBLANK are all read by the MPU through tristate buffers Fll. The MPU accesses this information via address decode INO2.
The option switch toggles of J11 are all read by the MPU through tristate buffers H11. The MPU accesses this information via address decode INO3. i. audio mixer/generator
(See Figure 4-14)
The audio mixer/generator produces crowd noise,
The NOTE signal is produced by counters D9 and D10. The MPU loads latch E10 with the period of the note to be produced. The counters load the period information from the latch each time the counters reach their maximum count.
BOUNCE audio is directly generated by the MPU thru data line DBUS4.
The three sounds are summed at the input of op-amp B11 (one quarter of LM324) and fed off the game PCB to the audio PCB for amplification.
Basketball™ 4-19
Pravoin [5] 1 [7c STEERING PoB- ————— -)
i Ss fe ;
ae
! BB RK (Seen Veanafs-—t 4 boo LL
ie
FTE fe} 7-10
an we puwvomn [E} BONTER wal rower [F 38 Eye Tt -— 6 le evs «| je 7
- S20 fp :
vp ‘ +sv—4+>— PELE ry FEEE! RI SRB ‘Th, STARTID 10K 10K FIOK TP, START! >— xe seare2 [a] sane [i start a fe staat af
piano [xf puaTee st o
a5y
putupin [lo} wre } RA
4-20 Basketball™ NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction. lorbidden without the specitic written permission of Atari, Inc., Sunnyvale, California, This drawing is only conditionally isoued, and either recelptror possassion thereo! confers or transters any right in, of license to use, the subject matter of the Grawing of any design or technical Information shown thereon, nar any right To reproduce this deawing or any part theteot, except for manulacture by vendors of Atari, incor porated and for manufacture under the corporation's writ {on license, no right to reproduce this drawing is granted for tie subject matter thereof unless by written agreement with oF written permission liom the corporation.
Figure 4-13 Trak Ball and Switch Input Schematic Diagram (Part of Game PCB 034268-XX A)
Te, CONT ve, wT WOMB
| R50 | SR20 | Snes | Sean | Sere | Sars |
| 10K | S10K | P1OK | SIOK | SIOK | SICK, |
+p py tidal
| Se} | EL | el | el | 2h | 2 | gl |
TH eros | tony Sirs | ‘orc
| Lasevace | u | 2b | seusy | |||
| Lamavace, | | | t | s| | ->- | = | . |
| iret | rt | 3] | an | |||
| esac | dia. | el | bs24d | fig | 5 |
sp com wove 3 ‘
| sP cown Move | ots | is | s | : | |
| cow move | co | 4 | Je | 2 | |
| com move | f-2! | is | 1 | fs | ' |
| com Move | +! | — | ed | Ho | _peuse |
ns
| {UM | sv) | ig ae | ry |
rs
Figure 4-13 (Continued) *
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction. forbidden without the Specitic writen permission of Alar, Inc. Sunny California. This drawing is only conditions ‘nolther receipt nor possession thereal canvers or ansters fy right in, oF license to use, the subject matter of the Grawing oF any design or technical information shown thereon, sor any right to reproduce this drawing or any part thereat except for manulactute by vendors of Alar Incr: poraied and for manufacture undar the corporation's writ. {en license, no right to reproduce this drawing is granted ‘or the sunject matter thereot unless by written agreament {with or weften permission trom the corporation.
Basketball™ 4-21
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction fortidden without the Specific written permission of Atari, Inc.. Sunnyvale, California. This grawing is only conditionally issued, ard neither receipt nar possession thereat conters or transters any right in, of license to use, the subject matter of tne rawing or ‘any design ‘or technveal information. shown thereon, nor any right to rapreduze this drawing or any part thereat oxceptit manufacture by vendors ol Ala, neo Porated and for manufacture under the corporation's wit fen license, no right 'o reproduce this drawing is granted fr tne subject matter tereo! unless ty written agreement with or weltten permission from the corporation, te COUNTER, Gaowac aD c
Zc io |
ere]
PRI Snore,
ls e fees ‘i ase oo 2, fs we wwe toe ae fa eas le jean aes Is oc ele Bio anf& At ape eal dbs 2, wreath sumeef mary acfi2 aul? auf ‘NOISE ¢ — Leah e 9 oD
Toa
nee css
as) cee Bounce ——~WA——_i —+4 oat
sv
aso Be ee a
DBUs¢- 1D 19 BOUNCE
Deusa—"]4D ew 4als [S08 SeK B :
4-22 Basketball™ 30K
Figure 4-14 Audio Schematic Diagram (Part of Game PCB 034268-XX A {za} aves {ia} AvDio ov
X]Auvi0 ano,
illustrated parts catalog
The purpose of this Chapter is to provide you with the necessary information for ordering replacement parts for your game.
When ordering parts from your distributor, give the part number, part name, applicable figure number from this Catalog, and the serial number of your game. This will help avoid confusion and mistakes in your order. We hope the result will be less down time and more profit from your game!
Basketball™
5-2 Basketball™ Figure 5-1 Final Assembly 034509-01 B NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL’ Reproduction. forbidden without ine ritlen_ peri q ‘Sunnyvale, ‘issued, and ortransters alter of the Alanine.
igh f The sul drawing or any sesign or technical_information, shown {fareon norany right to reproduce ths drawing or any part i pt for manutac\ re by vendors of Atari, incor ‘for manufacture under the corporation's wnt reduce this Srawing is granted 0! uniess by written agreement fon from the corporation.
Figure 5-1 Final Assembly Parts List
A034349-01 A034352-01 A034355-01 A007902-01 A007197-01 A009083-01 A034353-01 A034543-01 A033016-01 A034268-01 A009574-02 70-301 92-032 034323-56 034356-01 009992-01 007882-02 48-004 000869-01 034327-01 034326-01 006870-01 005594-01 46-2013002 99-11006 75-990505S 75-045 78-25002 72-6610 72-6812 72-6820 034509 75-010S 75-015S 75-5520B 75-935 82-1824 82-8016 75-040B 75-5523B 75-5120B 75-9118 75-931 Cabinet Assembly Fluorescent Light Assembly (Figure 5-2) Control Panel Assembly (Figure 5-3) Cash Box Assembly Type “B” Power Supply Assembly (Figure 5-6) Coin Door Assembly (Figure 5-7) Rear Door Assembly Main Harness and Comp Assembly Power Cord Assembly Basketball PCB Assembly (Figure 5-8) Audio Amplifier PCB Assembly (Figure 5-9) 24” Fluorescent Lamp 23” Black and White TV Monitor Upper Attraction Panel Retainer Strip Lower Attraction Panel Retainer Strip Power Switch Cover Interlock Switch Cover 8 Ohm, 5 Watt, 5” Loudspeaker 5” Speaker Grille Bezel with Graphics Attraction Panel with Graphics Coin Box Bracket Monitor Tie-Down Bracket 3A, Type 3AG Slow-Blow Fuses Lamp Socket Clip Hexagonal Polymer Self-Locking Steel Nut 1%” Split Lock-Washer Screw-Down Tie Wrap #6 x 5/8” Pan-Head Self-Tapping Screw #8 x 3/4” Pan-Head Self-Tapping Screw #8 x 11/4” Pan-Head Self-Tapping Screw Yq” x 20 Flat-Head Cap Screw with Thread Locking Compound #10 Flat Steel Washer Yq” Flat Steel Washer Yq” x 20 x 1.25” Black Oxide Carriage Bolt Yq” x 20 Wing Nut #8 x 11/2” Flat-Head Wood Screw #10 x 32 x 1” Socket-Head Button Cap Screw #10 Black Split Lock-Washer Yq4” x 20 x 1.43” Black Carriage Bolt #10 x 24 x 1.25” Black Carriage Bolt #10 x 24 Standard Pattern Steel Hexagonal Machine Nut #10 x 24 Wing Nut WMNANAWNH
ATART
Basketball™ 5-3
NOTICE To ALL PERSONS RECEIVING THIS GRAWING CONFIDENTIAL: Reproduction Igricden Specilic written germission of Ala, Glioma’ This arawing only eencitiona neither receipt nor possession thereat cont Any right in, oF ieanse to-use, the subject matter othe Grawing 2° any design or technical Information shown thereon, nor any rignt to ceproduce this drawing or any part thereo? ‘exceal for manufacture by vendors of Ata’, incor P icture under the corporation's wri feproduce this drawini or the subject ms Funiess By written agi Wilk-or written permission Trom the Corporation.
AOCESCENT| TUBE GROAN | AS EEE
034335:01 A034753-01 7268105
75-018S
5-4 Basketball™ Figure 5-2 Fluorescent Light Assembly A034352-01 B
Figure 5-2 Fluorescent Light Assembly Parts List
Light Support Board 24” Fluorescent Light Assembly #8 x 5/8” Cross-Recessed Pan-Head Thread-Forming, Type AB Sheet-Metal Screw #8 Flat Washer
e100 OOO OCo,,
(2 KEOD.) NOTERS~ | TRACKBALL BEAZINGS TO BE LUBRICATED WITH 3m ONE"OIL ONLY.
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction. lorbiaden without. the Specitc written, permission of ‘Atst,_Inc.. Sunnyvale, Gaiifornia. This drawing #8 only condi thereon. nor any right (0 reproduce this drawing or any part ‘Meteo? except for manufacture by vendors al Alati incor porated and for manutacture under the corporation's wri {en license, no right lo reproduce this drawing is granted fo the Subject matter thereo! unless by written agreement sine welten permission tom the corporation Figure 5-3 Control Panel Assembly A034355-01 A
Figure 5-3 Control Panel Assembly Parts List [tem | _PartNumber [Qy. | Descripon 034325-01 Control Panel with Graphics A033360-01 Trak Ball™ Assembly (Figure 5-4) 033127-01 Black Switch Bushing (Start Switch) 62-002 Single Pole, Double Throw Pushbutton Type, Momentary Action Lighted (LED) Switch 75-07054 -47” LD. by .968” O.D. x .075” Thick Flat Nylon Washer 75-5512N 1/4”-20 x 4" Round-Head, Square-Neck, Nickel Plated Carriage Bolt 75-015S 1/4” Flat Steel Washer 75-990505S, 14”-20 Self-Locking Steel-Based Polymer Hexagonal Nut A034543-01 Control Harness
Basketball™ 5-5
NOTIGE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction. forbidden without the specific watten permission of Alar, Inc, Sunnyvale, This drawing ts only conditionally issued. and ipt nor possession thereof conters or tansters any right in. oF license to use, the subject matter of the ‘drawing or any design or technical information, shown {peteon. ne any ah oreproduce his Grawing orany part thereof, except for manulacture by vendors ol Avan, Ineo! 1nd for manufacture under the corporation's wil or {en license, no right 10 reproduce this drawing 's granted or the subjéct matter thereof unless by wattes agreement with oF wiilten permission from the corporation.
5-6 Basketball™ Figure 5-4 Trak Ball™ Assembly A033360-01 F
Figure 5-4 Trak Bail™ Assembly
033355-01 033356-01 033357-01 033358-01 033359-01 033361-01 033362-01 033363-01 033364-01 033365-01 000616-01 033366-01 74-5404NN A009060-02 76-13003 73-3006 72-8808 72-1006S CwmrIAnhone NONTN PENH HRN DONE EEE
72-1606S ES Parts List | tem | Part Number | __Qy. | Descpton | Base Plate Top Plate Cover Plate Corner Post End Post PCB Bracket Roller Shaft Stand Off Adjustable Post Spacer Light Hub 4!” Diameter Rubber Bali 1/8” 1.D., 4” O.D. x 1%” Nylon Spacer Steering PCB Assembly (See Figure 5-5) Fafnir 53K or New Departures R6 Bearing 3/8” Shaft Diameter Retaining Ring #8-32 x '%2” Hex-Socket Machine Cap Screw #10-32 x 3/8” Pan-Head, Cross-Recessed Cadmium-Plated steel Machine Screw #6-32 x 3/8” Pan-Head, Cross-Recessed Cadmium-Plated Steel Machine Screw 72-1408S S #4-40 x 1/2” Pan-Head, Cross-Recessed Cadmium-Plated Steel Machine Screw #3/8-16 x 144” Hexagonal Socket Machine Cap Screw #8-32 x 1/2” Black Oxide Flat-Socket Head Cap Screw #6-32 x 1/2” 82° Flat-Head Cross-Recessed Cadmium-Plated Steel 72-8920S 85-1808B 75-3608S
75-046S 75-048S 75-040S 75-041S 75-010S 75-0188, 75-0168 Machine Screw #6 Corrosion-Resistant Steel Split Lock-Washer #8 Cortosion-Resistant Steel Split Lock-Washer #10 Corrosion-Resistant Steel Split Lock-Washer 3/8” Corrosion-Resistant Steel Split Lock-Washer #10 Corrosion-Resistant Steel Flat, Plain Washer #8 Corrosion-Resistant Stee] Flat, Plain Washer #6 Corrosion-Resistant Steel Flat, Plain Washer PWNNHHE DOR WEE
75-990504C #4-40 Steel Hexagonal Self-Locking, Shallow Pattern, Prevailing Torque Nut #6-32 Steel Standard Pattern Hexagonal Machine Nut 3/8” Steel Standard Pattem Hexagonal Machine Nut 75-9168 75-9195 ae)
ATART’
Basketball™ 5-7
°
E] eepeei-0! RB cewine ep
rot kee yoosceo NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: ‘Reproduction forbidden shout the specific ‘wrlltes_permission Of Atart, Inc. Sunnyvale, Catifornia. This ctawing is chly conditionally #ssued, and ‘either receipt nor possession thereot covers or transfers ny fight in, or license to use, tne subject matter ct the Gawing oF any desiga or technical Information. snown thereon, nor any ngntiorepraduce iis drawing or any part Inert except for manulactureby vendors of Mai, ncor porated and for manulacture under the corporation's writ {ea license, no right to repreduce this drawing is granted Or the subject matter thereof unless by written agreement with oF written permission irom the corparation. J2 ev IATA °
TRACES SHOWN ARE ON OPPOSITE SIDE
Figure 5-5 Steering Board Assembly A009060-02 C
Figure 5-5 Steering Board Assembly Parts List ios Parton] 10-5392 10-5331 10-5471 27-250104 3.9k ohm, +5% V4W Carbon Resistor 330 ohm, +5% %4W Carbon Resistor 470 ohm, +5% /4W Carbon Resistor 0.1 uf, +20%, 25V, Ceramic Disk Capacitor 10 yf, + 10%, 20V, Tantalum Axial Lead Capacitor Transistor (2N3643) 10 Contact Connector Radial Optical Coupler 29-046 34-2N3643 79-58005 030369-01 PeENRPEN AN
5-8 Basketball™
TOP VIEW
\ mi 4REQD ae:
BOTTOM VIEW
NOTICE T0 ALL PERSONS RECEIVING THIS DRAWING ONMDENTIAL’ Reprocuetion Torbidder without ie Srecitic writen. permission ‘of Atari ne. "Sunnyvale Gaivorna’ The ofawing ie only cordiionally ‘sued, and neitherrecelpt nov possestion thereat confers 9: transfers any ight invor teense to une, the subject mater of the Grawing or any design or technical tyormation shown thereon, rorany ght fo reproduce ins drawing or any pat ineteot, excep formanutactare wy vendors Avan feer pated anor manufctre unde: the covoratlon's il onticenge, nu igh tg eroduce I Gaming's panted Orne ubyéel matter ergot uness Sy water agreement Figure 5-6 Type B Power Supply Assembly Win's'wrtien permission nam the corporation
Figure 5-6 Type B Power Supply Assembly Parts List
A009266-01 Power Supply Base Weidment Assembly A006886-01 Type B Transformer Termination Assembly, Type B 29-053 1 Sprague 26,000 uf, 15V Electrolytic Capacitor, Type 36DX263G015BM2B Sprague #4586-48 Capacitor Mounting Bracket P.C. Board Rectifier Panel Mounting Fuse Holder 5-Amp Power Line Filter Voliage Selection Block, (95V - Black) Voltage Selection Block, (110V - Orange) Voltage Selection Block, (205V - Green) Voltage Selection Block, (220V - Red) #8-32 x 5/8” Pan-head Steel Screw #8 Split Lock-Washer #8 Steel Hexasonal Machine Nut #8 Flat Steel Washer Power Switch Termination Power in Harness 8 Amp, 125 Volt Fast-Blow Type 3AG Fuse 2.5 Amp, 125 Volt Slow-Blow Type 3AG Fuse 78-70501SC A006555-01 79-4411004 41-2003 A006958-01 A006858-02 A006858-03 A006858-04 72-1810S 75-048 75-9188 75-018S A007192-01 A007444-01 46-203801 46-201251
Basketball™ 5.9
- - F (6) 2 PLCS @)
- 2 PLCS (Ss) 2 PLCS
- 2 PLCS 2 PLCS @2)
4 PLCS
YEL' YEL/BK BK/YEL
NOTICE TO ALL PERSONS RECEIVING THiS ORAWING “ONDE
any right in, er license to use, the subjact matter of the Grawing oF ‘any Gesign or technical information shown
Figure 5-7 Coin Door Assembly A009083-01 D
5-10 Basketball™
Figure 5-7 Coin Door Assembly Parts List
[tem [Part Number [_Qiy._| Description
WONDMKHARWHY A007637-01 A007637-02 A007637-03 A007637-04 A007637-05 007637-06 A007637-07 75-9165 A030362-01 A007640-01 A002465-01 004320-01 004341-01 004344-01 004340-01 004337-01 004338-01 004336-01 004326-01 75-046 006904-01 007359-01 70-11-47 73-3008 75-9914001 75-0268 75-00516 008629-01 71-2118 71-1225CU 71-125FB 71-1205MG 71-1201KS 71-1201YJ 71-1210PE 71-1220CA 007753-01 A007638-01 A006921 Front Bezel Assembly -01 coin door assy. only—(25 ¢ Front Bezel Assembly -02 coin door assy. only—(5 Fr.) Front Bezel Assembly -03 coin door assy. only—(1 DM) Front Bezel Assembly -04 coin door assy.—(1 Kr) Front Bezel Assembly -05 coin door assy. only—(100 Y) Front Bezel Assembly -06 coin door assy. only—(10 pence) Front Bezel Assembly -07 coin door assy. only—(20 Australian) #6-32 Nut Coin Lock-out Assembly Coin Switch Assembly Coin Counter Assembly Coin Door Weldment Secondary Coin Chute Key Loop Spring Return Wire Form Bracket R.H. Lock-Out Wire Form L.H. Lock-Out Wire Form Scavenger Button #6 Lockwasher Spacer Lamp socket Lamp Truarc #5103-25 Retaining “C” Ring Self-Threading Tinnerman Nut, #SR188006 #6 Washer #6-32 Style #842 Steel Kepnut Spring Lock assembly Coin Mechanism for American Quarter Only Coin Mechanism for Belgian 5 Francs Only Coin Mechanism for German Mark Only Coin Mechanism for Swedish Krona Only Coin Mechanism for Japanese 100 Yen Only Coin Mechanism for English 10 Pence Only Coin Mechanism for Australian 20-Cent Piece Only Anti-probe Plate Slam Switch Assembly Harness Assembly
ATARI
Basketball™ 5-11
(02 VERSION? 2.0.,20W (-01 VERSION)
4a. iow
See NOTE 2
-01 VERSION
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL =O) VERSION:
‘or writien permission irom fe corporation Figure 5-8 Basketball Game PCB Assembly A034268-01 A
5-12 Basketball™
Figure 5-8 Basketball Game PCB Assembly Parts List
[term [Part Number | _Qy. | Description eesignation 034269-01 Printed Circuit Board
| 10-5101 | 100 ohm, +5%, 1/4 Watt, Carbon Resistor | R51 |
| 10-5221 | 220 ohm, +5%, '/ Watt, Carbon Resistor | R27,28,63 |
| 10-5331 | 330 ohm, +5%, 1% Watt, Carton Resistor | R3,4 |
| 10-5471 | 470 ohm, +5%, '% Watt, Carbon Resistor | R10,11,12 |
| 10-5102 | 1 k-ohm, +5%, '%4 Watt, Carbon Resistor | R1,2,5,9,12- |
14,21,62
| 10-5152 | 1.5kohm, +5%, 14 Watt, Carbon Resistor | R18 |
| 10-5472 | 4.7 k-ohm, +5%, 1% Watt, Carbon Resistor | R68 |
| 10-5103 | 10 k-ohm, +5%, 1% Watt, Carbon Resistor | R20,23- |
59,66 22 k-ohm, +5%, 1% Watt, Carbon Resistor R64 47 k-ohm, +5%, 1/4 Watt, Carbon Resistor R56,57,61 56 k-ohm, +5%, 4 Wait, Carbon Resistor 68 k-ohm, +5%, 1/4 Watt, Carbon Resistor 100 k-ohm, +5%, 1% Watt, Carbon Resistor 220 k-ohm, +5%, 1% Watt, Carbon Resistor 330 k-ohm, +5%, 1% Watt, Carbon Resistor 390 k-ohm, +5%, 1/4 Watt, Carbon Resistor 2 ohm, 20 Watt Wirewound Resistor .022 uf, +10%, 100V Mylar Capacitor .01 pf, + 10%, 100V Mylar Capacitor 10 uf, (-)10%, +50%, 25V Electrolytic Capacitor 220 uf, -10%, +50%, 25V Electrolytic Capacitor .01 pf, 20%, 25V Ceramic Disk Capacitor C44-51,53, 54,57 0.1 pi, + 20%, 25V Ceramic Disk Capacitor C1-20,22-41, 43,52,62,63 001 yf, 20%, 25V, Ceramic Disk Capacitor C58 .22 ut, 20%, 25V, Ceramic Disk Capacitor cél 100 pF, +5%, 25V Mica Capacitor c42 1N914 Diode CR1 2N3643 Transistor Q2,Q3 2N6044 Transistor Ql 10-5223 10-5473 10-5563 10-5683 10-5104 10-5224 10-5334 10-5394 19-10020001 21-101223 21-101103 24-250106 24-250227 27-250103 BNE Ree eee Oe
ay ary
27-250104 B
27-250102 27-250224 28-101101 31-1N914 34-2N3643 34-2N6044, 37-74LS00 37-74LS02 37-74LS04 Integrated Circuit, 74LS00 A5,D5,L7,R9 Integrated Circuit, 74LS02 N7,M9 Integrated Circuit, 741.S04 D4,R6,E9, P9,R2 Integrated Circuit, 74S04 R3 Integrated Circuit, 74LS08 B2,D6,D11 Integrated Circuit, 74LS10 R8,R10 OWE NH EEE
37-74804 37-74LS08 37-741.S10 Nor
ATARI
Basketball™ 5-13
Figure 5-8 Basketball Game PCB Assembly Parts List, continued
Sa
| 37-74LS14 | Integrated Circuit, 74LS14 | L10,K11 |
37-74LS20 Integrated Circuit, 74LS20 37-74LS32 Integrated Circuit, 74LS32 37-74LS42 Integrated Circuit, 74LS42
| 37-74LS74 | Integrated Circuit, 74LS74 | PS, RT) K9, |
K10 Integrated Circuit, 74S74 H8,N9,P10 Integrated Circuit, 74LS83 H6,J6 Integrated Circuit, 74LS86 N10 Integrated Circuit, 7490 cS Integrated Circuit, 74107 c10 Integrated Circuit, 74LS153 F4,H4,K4,L4, M4,N8 Integrated Circuit, 74LS157 A8,B8,C8,D8 Integrated Circuit, 74LS161 D9,D10 Integrated Circuit, 74LS163A L6,K7 Integrated Circuit, 74LS164 A10,B10 Integrated Circuit, 74LS166 A9,E8 Integrated Circuit, 74LS174 L8,M8,E11 Integrated Circuit, 74LS175 P7 Integrated Circuit, 74LS191 H9,J9,H10, J10 Integrated Circuit, 74LS244 C2,M3,N3, P3,F9 F11, Hl1l1
| 37-74LS273 | Integrated Circuit, 74LS273 | F6,E10 |
| 37-74LS374 | Integrated Circuit, 74LS374 | E4,K6,F7,H7 |
37-8T28 Integrated Circuit, 8T28 37-9316 Integrated Circuit, 9316 ANAND
37-74S74 37-74LS83 37-74LS86 37-7490 37-74107 37-74LS 153 ArHeenw
37-74LS157 37-74LS161 37-74LS163A 37-74LS 164 37-74LS 166 37-74LS174 37-74LS175 37-74LS191 PRWNNNNA
37-74LS244
37-9321 Integrated Circuit, 9321 37-9334 Integrated Circuit, 9334 37-LM323K LM323 Regulator I.C. 37-LM324 LM324 Audio Amplifier I.C. 62-001 SPST Momentary Contact Switch 66-118PIT SPST x 8 DIP Switch 81-4302 Nylon Snap-in Fastener 72-1608C #6-32 x 1/2” Cross-Recessed Pan-Head, Corrosion- Resistant Steel Machine Screw 75-016C #6 Flat Corrosion-Resistant Steel Washer 75-056C #6 Internal Tooth Corrosion-Resistant Steel Lock-Washer 75-916C #6-32 Hexagonal Corrosion-Resistant Steel Machine Nut
ATARI”
5-14 Basketball™
Figure 5-8 Basketball Game PCB Assembly Parts List, continued
a
83 78-06001 Heatsink (LM323K) 78-16005 Silpad (LM323K) 009470 Heatsink (82S17) 79-42C40 40 pin Medium Insertion Socket 90-102 12.096 MHz Crystal 90-6010 6502 Microprocessor 90-7019 2111A-4 RAM 90-7022 82S17 OR 82816 RAM J8,K8 90-7031 2101A-4 RAM F3,H3,K3,L3, F5,H5,K5,L5 ONNHREE NEY
034756-01 034759-01 034760-01 034761-01 034762-01 Sync PROM PROM Al PROM PROM AO PROM PROM B1 PROM PROM BO PROM Bee
Program (ROM) Memory Table of Equivalents
-01 PCB -01 PCB -02 PCB Self-Test (1K x 4 PROM Chips) (2K x 4 PROM Chips) (4K x 8 ROMs) Display
ROM BAD A 034765 ROM BAD C ROM BAD B ROM BAD D ROM BAD E ROM BAD G ROM BAD F ROM BAD H ROM BAD I ROM BAD K ROM BAD J ROM BAD L ROM BAD M ROM BAD O ROM BAD N ROM BAD P
ATART
Basketball™ 5-15
NOTICE TO ALL PERSONS AECENVING THIS DRAWING CONFIDENTIAL: Reproduction. forbidden without ine ‘Specitic written permission of Alar, Inc., Sunnyvale, Galitornia’ This eeawing ie Only conditionally issued, and neither receipt nor possession thereol conters or ransiers Grawing oF any design or technical information shown thereon, nor any “ght to reproduce this drawing or any part thereof, except for manulacture by vendors of Atart, incor Porated ana for manulacture under the corporation's wnt fenlicense. no right to repreduce this drawing Is granted ‘or the Subject matter inereo! unless by written agreement ‘wilt or written permission irom the corporation
5-16 Basketball™ AYCC@OOA ga GMA OIGUA JAUG to-eveeoo 8Y'O IAATA Agu_wl_3gam
ut GIT DA2002"
ba Oo
TRACES ARE ON
OPPOSITE SIDES
Figure 5-9 Audio PCB Assembly A009574-01 C
Figure 5-9 Audio PCB Assembly Parts List SS a a mMECwr x.H aWN 10-51PO 10-5101 10-5100 11-5221 19-316103 24-250106 24-240107 24-250108 24-250228 27-101103
27-250104 31-A14F 31-1N4001 37-TDA2002V 69-004 78-58005 030184-01 72-1604C
75-056 78-16009 10-5103 Bee eee ee
WeeeHaNn
HH ow 1 Ohm, +5%, 1% Watt, Carbon Resistor 100 Ohm, +5%, 1/4 Waitt, Carbon Resistor 10 Ohm, +5%, % Watt, Carbon Resistor 220 Ohm, +5%, 1/2 Watt, Carbon Resistor 10K-Ohm Trimpot 25V, 10 uf -10%, +50% Electrolytic Cap. 25V, 100 yf -10%, +50% Electrolytic Cap. 25V, 1000 pf - 10%, +50% Electrolytic Rap. 25V, 2200 uf — 10%, +50% Electrolytic Cap. 100V, .01 pf —20%, +50% Ceramic Disc Cap. 25V, 0.1 pf + 20% Ceramic Disc Cap. A14F, 50 PIV High Curent Rectifier 1N4001 Diode TDA2002V Audio Amp. Slide Switch 10 Contact Connector Heat Sink #6-32 x 1%” Pan-Head Cross-Recessed Steel Machine Screw #6 Interior Star Lock Washer Silpad +5% 10K-Ohm, +5% 1/4 Watt Carbon Resistor C4, 11 CRI, 2 CR8-CR12
Basketball™ 5-17
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Cut along this line
YOUR COMMENTS, PLEASE!
Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A.
If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.
Page: Comments:
Fill in if you wish a reply:
Name Firm _. (Distributor Operator Address © Other________
City _ State Zip ‘TM-137 Ist printing
First fold
BUSINESS REPLY MAIL
FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA
POSTAGE WILL BE PAID BY ADDRESSEE
Atari, Inc. Attn: Publications/Coin-Op Eng. P.O. Box 427 Sunnyvale, California 94086
Second fold
a6po sip adey No Postage Necessary if mailed in the United States
Cut along this line
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Pk BE BER RE RE Re RES RN 20
= »
= = Pdlee, Males Satie! ates Nae Sad Satae Natee
WARRANTY
Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller’s other products or parts thereof are warranted. -
If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
- Such products are returned prepaid to Sellers’ plant; and
- Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed’and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.
In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.
Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller’s part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.
This document is and contains confidential trade secret information of Atari, Inc.
This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.
Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc. eZ s s
© © © s IS
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.