CATHODE RAY TOMES

Club Kart DX

Club Kart (SEGA, 2001) · Manual · 159 pages · 145 sections · original scan

Page 1

Deluxe Version

OWNER’S MANUAL

SEGA ENTERPRISES, INC. USA

MANUAL NO. 999-1275

Page 2

VISIT OUR WEBSITE!

© SegaService.com

SEGA

Ask Dave! = Derive oe

people have visited this page since 3/16/01

ee Ifyou have any questions or comments vu si Department a,

Prsnseg eee about this site please E-Mail to Darl Davidson@seu sega com

fax 495.701.0606

THUS WES BITE POWERED BY

WebSTAR 4-3

ld

You will need the following items to view this page in its entirety (seo I . B All Platfoms Windows Macmtosh

Page 3

BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING: To maintain the safety:

To ensure the safe usage of the product, be sure to read the following before using the product. The following instructions are intended for the users, operators and the personnel in charge of the operation of the product. After carefully reading and sufficiently understanding the warning displays and cautions, handle the product appropriately. Be sure to keep this manual nearby the product or elsewhere convenient for referring to it when necessary.

Herein, explanations which require special attention are enclosed with dual lines. Depending on the potentially hazardous degrees, the terms of WARNING, CAUTION, etc. are used. Be sure to understand the contents of the displays before reading the text.

Indicates that mishandling the Indicates that mishandling the product product by disregarding this by disregarding this caution will cause

warning will cause a potentially a slight hazardous situation which can
WARNING! hazardous situation which can CAUTION! result in personal injury and or material result in death or serious injury. damage.

For the sage usage of the product, the following pictographs are used:

Indicates “HANDLE WITH CARE.” In order to protect the human body an equipment, this display is attached to places where the Owner’s Manual and or Service Manual should be referred to.

© Perform work in accordance with the instructions herein stated. Instructions for work are explained by paying attention to the aspect of accident prevention. Failing to perform work as per the instructions can cause accidents. In the case where only those who have technical expertise should perform the work to avoid hazardous situation, the instructions herein state that the serviceman should perform such work.

© Be sure to turn off power before working on the machine. To prevent electric shock, be sure to turn off power before starting the work in which the worker touches the interior of the product. If the work is to be performed in the power-on status, the Instruction Manual herein always states to that effect.

© Besure to ground the Earth Terminal (this, however, is not required in the case where a power cord with earth is used). This product is equipped with the Earth Terminal. When installing the product, Connect the Earth Terminal to the “accurately grounded indoor earth terminal” by using an earth wire. Unless the product is grounded appropriately, the user can be subject to electric shock. After performing repair, etc. for the Control equipment, ensure that the Earth Wire is firmly connected to the Control equipment.

© Ensure that the Power Supply used is equipped with an Earth Leakage Breaker. This product does not incorporate the Earth Leakage Breaker. Using a power supply which is not equipped with the Earth Leakage Breaker can cause a fire when earth leakage occurs.

© Be sure to use fuses which meet the specified rating. (only for the machines which use fuses). Using fuses exceeding the specified rating can cause a fire and electric shock.

Page 4

© Specification changes (removal of equipment, conversion and addition) not designated by SEGA are not allowed. The parts of the product include warning labels for safety, covers for personal protection, etc. It is very hazardous to operate the product by removing parts and or modifying the circuits. Should doors, lids and protective parts be damaged or lost, refrain from operating the product, and contact where the product was purchased from or the office herein stated. SEGA shall not be held responsible for any accidents, compensation for damage to a third party, resulting from the specifications not designated by SEGA. ©. Ensure that the product meets the requirements of appropriate Electrical Specifications. Before installing the product, check for Electrical Specifications. SEGA products have a nameplate on which Electrical Specifications are described. Ensure that the product is compatible with the power supply voltage and frequency requirements of the location. Using any Electrical Specifications different from the designated Specifications can cause a fire and electric shock. © _ Install and operate the product in places where appropriate lighting is available, allowing warning labels to be clearly read. To ensure safety for the customers, labels and printed instructions describing potentially hazardous situation are applied to places where accidents can be caused. Ensure that where the product is operated has sufficient lighting allowing the warnings to be read. If any label is peeled off, apply it again immediately. Please place an order with where the product was purchased from or the office herein stated. © When handling the Monitor, be very careful. (Applies only to the product w/monitor.) Some of the monitor (TV) parts are subject to high tension voltage. Even after running off power, some portions are still subject to high tension voltage sometimes. Monitor repair and replacement should be performed only be those technical personnel who have knowledge of electricity and technical expertise. © Besure to adjust the monitor (projector) properly. (Applies only to the product w/monitor.) Do not operate the product leaving on-screen flickering or blurring as it is. Using the product with the monitor not properly adjusted may cause dizziness or a headache to an operator, a player, or the customers. © _ When transporting or reselling this product, be sure to attach this manual to the product. In the case where commercially available monitors and printers are used in this product, only the contents relating to this product are explained herein. Some commercially available equipment has functions and reactions not stated in this manual. Read this manual together with the specific Instruction Manual of such equipment.

  • Descriptions herein contained may be subject to improvement changes without notice. © The contents described herein are fully prepared with due care. However, should any question arise or errors be found, please contact SEGA.

INSPECTIONS IMMEDIATELY AFTER TRANSPORTING THE PRODUCT TO THE LOCATION.

Normally, at the time of shipment, SEGA products are in a status allowing for usage immediately after transporting to the location. Nevertheless, an irregular situation may occur during transportation. Before turning on power, check the following points to ensure that the product has been transported in a satisfactory status. Are there any dented portions or defects (cuts, etc.) on the external surfaces of the cabinet? Are Casters and Adjusters, damaged? Do the power supply voltage and frequency requirements meet with those of the location? Are all wiring connectors correctly and securely connected? Unless connected in the correct direction, connector connections can not be made accurately. Do not insert connectors forcibly. Do power cords have cuts and dents? Do the fuses used meet specified rating? Is the Circuit Protector in an energized status? Are all accessories available? Can all Doors and Lids be opened with the Accessory keys? Can Doors and Lids be firmly closed?

Page 5

TABLE OF CONTENTS

BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING: TABLE OF CONTENTS

INTRODUCTION OF THE OWNER’S MANUAL HANDLING PRECAUTIONS ... PRECAUTIONS CONCERNING INSTALLATION LOCATION

OPERATION ....

NAME OF PARTS

ACCESSORIES

  • ASSEMBLING AND INSTALLATION

PRECAUTIONS TO BE HEEDED WHEN MOVING THE MACHINE

  • CONTENTS OF GAME ‘0
  • EXPLANATION OF TEST AND DATA DISPLAY. 9-1 SWITCH UNIT AND COIN METER ..

9-2 SYSTEM TEST MODE

9-3 GAME TEST MODE...

  • CONTROL PANEL 10-1 ADJUSTING/REPLACING THE VR.

10-2 GREASING...

  • ACCELERATOR & BRAKE

11 - 1 ADJUSTING AND REPLACING THE V.R.

11 -2 GREASING....

  • PROJECTOR 12-1 CLEANING THE SCREEN .. Va eye

12-2 ADJUSTMENT OF TOSHIBA PROJECTOR .... 80-89

12-3 ADJUSTMENT OF MITSUBISHI PROJECTOR 90- 92

  • COIN SELECTOR .... 93 -97
  • REPLACING THE FLOURESCENT LAMP, AND LAMPS .. 98 - 99
  • PERIODIC INSPECTION TABLE 100 - 101
  • TROUBLESHOOTING 102 - 104
  • GAME BOARD 105 - 107

17 - 1 REMOVING THE GAME BOARD 106 - 107

  • COMMUNICATION PLAY .. 108 - 115 18-1 INSTALLATION PRECAUTIONS .. 108 - 109 18-2. CONNECTING THE COMMUNICATION CABLE 109 - 113 18-3 SETTING FOR COMMUNICATION PLAY .. 114-115 18-4 CAUTIONS TO BE HEEDED DURING COMMUNICATION PLAY 115
  • DESIGN RELATED PARTS 116-117
  • PARTS LIST... 118 - 148
  • WIRE COLOR CODE TABLE 149
  • WIRING DIAGRAM ..... 150 - 153
Page 6

SPECIFICATIONS Installation Space : 1,360 mm (W) X 2,610 mm (D) (53.5 in. X 102.8 in.) Height : 2,230 mm (87.8 in.) Weight : 450 kg. (992.1 Ibs.) Power, maximum current : 625 W 6.70 A (AC 120V 60 Hz AREA) 675 W 4.00 A (AC 220V 50 Hz AREA) 640 W 3.80 A (AC 220V 60 Hz AREAO 675 W 3.60 A (AC 240V 50 Hz AREA) For TAIWAN Power, current : 750 W 9.20 A (MAX.) 350 W 3.80 A (MIN.) MONITOR : 50 TYPE PROJECTION DISPLAY

INTRODUCTION OF THE OWNERS MANUAL

This Owner's Manual is intended to provide detailed descriptions together with all the necessary information covering the general operation of electronic assemblies, electromechanicals, servicing control, spare parts, etc. as regards the product, CLUB KART DX TYPE. This manual is intended for the owners, personnel and managers in charge of operation of the product. Operate the product after carefully reading and sufficiently understanding the instructions. If the product fails to function satisfactorily, nontechnical personnel should under no circumstances touch the internal system. Please contact where the product was purchased from.

Use of this product is unlikely to cause physical injuries or damages to property. However, where special attention is required this is indicated by a thick line, the word "IMPORTANT" and its sign in this manual.

Indicates that mishandling the product by disregarding this display can cause the product's intrinsic performance not to be obtained, resulting in malfunctioning.

MPORTANT

SEGA ENTERPRISES, INC. (U.S.A.)/CUSTOMER SERVICE 45133 Industrial Drive, Fremont, California 94538, U.S.A. Phone : (415) 701-6580 Fax : (415) 701-6594

Page 7

DEFINITION OF LOCATION MAINTENANCE MAN AND SERVICEMAN

WARNING! Non-technical personnel who do not have technical knowledge and expertise should refrain from performing such work that this manual requires the location's maintenance man or a serviceman to carry out, or work which is not explained in this manual. Failing to comply with this instruction can cause a severe accident such as electric shock.

Ensure that parts replacement, servicing & inspections, and troubleshooting are performed by the location's maintenance man or the serviceman. It is instructed herein that particularly hazardous work should be performed by the serviceman who has technical expertise and knowledge.

The location's maintenance man and serviceman are herein defined as follows:

"Location's Maintenance Man" : Those who have experience in the maintenance of amusement equipment and vending machines, etc., and also participate in the servicing and control of the equipment through such routine work as equipment assembly and installation, servicing and inspections, replacement of units and consumables, etc. within the Amusement Facilities and or locations under the management of the Owner and Owner's Operators of the product.

Activities of Location's Maintenance Man : Assembly & installation, servicing & inspections, and replacement of units & consumables as regards amusement equipment, vending machines, etc.

Serviceman : Those who participate in the designing, manufacturing, inspections and maintenance service of the equipment at an amusement equipment manufacturer. Those who have technical expertise equivalent to that of technical high school graduate: gards electricity, electronics and or mechanical engineering, and daily take part in the servicing & control and repair of amusement equipment. re-

Serviceman's Activities : Assembly & installation and repair & adjustments of electrical, electronic and mechanical parts of amusement equipment and vending machines.

LISTED

5K92 ®

AMUSEMENT MACHINE

Page 8
  • HANDLING PRECAUTIONS
WARNING!
IMPORTANT When installing or inspecting the machine, be very careful of the following points and pay attention to ensure that the player can enjoy the game safely. Non-compliance with the following points or inappropriate handling running counter to the cautionary matters herein stated can cause personal injury or damage to the machine.

@ Before performing work, be sure to turn power off. Performing the work without turning power off can cause an electric shock or short circuit. In the case work should be performed in the status of power on, this manual always states to that effect. To avoid electric shock or short circuit, do not plug in or unplug quickly. To avoid electric shock, do not plug in or unplug with a wet hand. Do not expose Power Cords and Earth Wires on the surface, (floor, passage, etc.). If exposed, the Power Cords and Earth Wires are susceptible to damage. Damaged cords and wires can cause electric shock or short circuit. To avoid causing a fire or electric shock, do not put things on or damage Power Cords. When or after installing the product, do not unnecessarily pull the power cord. f damaged, the power cord can cause a fire or electric shock. n case the power cord is damaged, ask for replacement through where the product was purchased from or the office herein stated. Using the cord as is damaged can cause fire, electric shock or leakage. Be sure to perform grounding appropriately. Inappropriate grounding can cause an electric shock. Be sure to use fuses meeting specified rating. Using fuses exceeding the specified rating can cause a fire or electric shock. Completely make connector connections for IC BD and others. Insufficient insertion can cause an electric shock. Specification changes, removal of equipment, conversion and/or addition, not designated by SEGA are not permitted. Failure to observe this may cause a fire or an electric shock. Non-compliance with this instruction can have a bad influence upon physical conditions of the players or the lookers-on, or result in injury during play. SEGA shall not be held responsible for damage, compensation for damage to a third party, caused by specification changes not designated by SEGA. Be sure to perform periodic maintenance inspections herein stated.

For the IC board circuit inspections, only the logic tester is allowed. The use of a multiple-purpose tester is not permitted, so be careful in this regard. The Projector is employed for this machine. The Projector's screen is susceptible to damage, therefore, be very careful when cleaning the screen. For details, refer to PROJECTOR.

Page 9
  • PRECAUTIONS CONCERNING INSTALLATION

LOCATION

WARNING! This product is an indoor game machine. Do not install it outside. Even indoors, avoid installing in places mentioned below so as not to cause a fire, electric shock, injury and or malfunctioning. @ Places subject to rain or water leakage, or places subject to high humidity in the proximity of an indoor swimming pool and or shower, etc. Places subject to direct sunlight, or places subject to high temperatures in the proximity of heating units, etc. Places filled with inflammable gas or vicinity of highly inflammable/volatile chemicals or hazardous matter. Dusty places. Sloped surfaces. Places subject to any type of violent impact. Vicinity of anti-disaster facilities such as fire exits and fire extinguishers. The operating (ambient) temperature range is from 5 C° to 40 C°. Only in the case a projector is employed, the temperature range is from 5 C° to 30.C°.

LIMITATIONS OF USAGE REQUIREMENTS

WARNING! Be sure to check the Electrical Specifications. Ensure that this product is compatible with the location's power supply, voltage and frequency requirements. A plate describing Electrical Specifications is attached to the product. Non-compliance with the Electrical Specifications can cause a fire and electric shock. This product requires the Breaker and Earth Mechanisms as part of the location facilities. Using them in a manner not independent can cause a fire and electric shock. Ensure that the indoor wiring for the power supply is rated at 15A or higher (AC single phase 100 ~ 120V area), and 7A or higher (AC 220 ~ 240V area). Non-compliance with the Electrical Specifications can cause a fire and electric shock. Be sure to independently use the power supply equipped with the Earth Leakage Breaker. Using a power supply without the Earth Leakage Breaker can cause an outbreak of fire when earth leakage occurs. Putting many loads on one electrical outlet can cause generation of heat and a fire resulting from overload. When using an extension cord, ensure that the cord is rated at 15A or higher (AC 100 ~ 120V area) and 7A or higher (AC 220 ~ 240V area). Using a cord rated lower than the specified rating can cause a fire and electric shock.
Page 10

OPERATION AREA

For the operation of this machine, secure a minimum area of 2.0m (W) X 2.8m (D). In order to prevent injury resulting from the falling down accident be a! during game play, be sure to secure the minimum area for operation. Be sure to provide sufficient space so as to allow this product's ventilation fan to function efficiently. To avoid machine malfunctioning and a fire, do not place any obstacles near the ventilation opening. SEGA shall not be held responsible for damage, compensation for damage to a third party, resulting from the failure to observe this instruction.

S For transporting the machine into the location's building, the minimum necessary dimensions of the opening (of doors, etc.) are 1.4m(W) and 1.7m(H).

IMPORTANT
  • Electric current consumption —

MAX. 6.7 A (AC 120V 60 Hz) MAX. 4.0 A (AC 220V 50 Hz) MAX. 3.8 A (AC 220V 60 Hz) MAX. 3.6 A (AC 240V_50 Hz) MAX. 9.2 A (For TAIWAN)

Page 11
  • OPERATION

PRECAUTIONS TO BE HEEDED BEFORE STARTING THE OPERATION To avoid injury and trouble, be sure to constantly give careful attention to the behavior and manner of the visitors and players.

In order to avoid accidents, check the following before starting the operation: @ To ensure maximum safety for the players and the customers, ensure that

WARNING! where the product is operated has sufficient lighting to allow any warnings to be read. Operation under insufficient lighting can cause bodily contact with each other, hitting accident, and or trouble between customers. Be sure to perform appropriate adjustment of the monitor (projector). For operation of this machine, do not leave monitor's flickering or deviation as is. Failure to observe this can have a bad influence upon the players' or the customers' physical conditions. It is suggested to ensure a space allowing the players who feel sick while playing the game to take a rest. Check if all of the adjusters are in contact with the surface. If they are not, the Cabinet can move and cause an accident.

Ensure that all of the Adjusters are in contact with the floor.

Do not put any heavy item on this product. Placing any heavy item on the product can cause a falling down accident or parts damage.

WARNING! Do not climb on the product. Climbing on the product can cause falling down accidents. To check the top portion of the product, use a step. To avoid electric shock, check to see if door & cover parts are damaged or omitted. To avoid electric shock, short circuit and or parts damage, do not put the following items on or in the periphery of the product. Flower vases, flowerpots, cups, water tanks, cosmetics, and receptacles/ containers/vessels containing chemicals and water.
Page 12

A

CAUTION! To avoid injury, be sure to provide sufficient space by considering the potentially crowded situation at the installation location. Insufficient installation space can cause making bodily contact with each other, hitting accidents, and or trouble between customers.

PRECAUTIONS TO BE HEEDED DURING OPERATION (PAYING ATTENTION TO CUSTOMERS)

A

WARNING!

A

CAUTION! To avoid injury and trouble, be sure to constantly give careful attention to the behavior and manner of the visitors and players.

@ To avoid injury and accidents, those who fall under the following categories are not allowed to play the game. Those who need assistance such as the use of an apparatus when walking. Those who have high blood pressure or a heart problem. Those who have experienced muscle convulsion or loss of consciousness when playing video game, etc. Those who have a trouble in the neck and or spinal cord. Intoxicated persons. Pregnant women or those who are in the likelihood of pregnancy. Persons susceptible to motion sickness. Persons whose act runs counter to the product's warning displays. A player who has never been adversely affected by light stimulus might experience dizziness or headache depending on his physical condition when playing the game. Especially, small children can be subject to those conditions. Caution guardians of small children to keep watch on their children during play. Instruct those who feel sick during play to have a medical examination. To avoid injury resulting from falling down and electric shock due to spilled drinks, instruct the player not to place heavy items or drinks on the product. To avoid electric shock and short circuit, do not allow customers to put hands and fingers or extraneous matter in the openings of the product or small openings in or around the doors. To avoid falling down and injury resulting from falling down, immediately stop the customer's leaning against or climbing on the product, etc. To avoid electric shock and short circuit, do not allow the customers to unplug the power plug without a justifiable reason.

Immediately stop such violent acts as hitting and kicking the product. Such violent acts can cause parts damage or falling down, resulting in injury due to fragments and falling down. Instruct the Player to adjust the seat before playing the game. Playing the game in a forcible posture can cause a contingent accident.

Page 13
  • NAME OF PARTS

BILLBOARD

PTV

50 TYPE PROJECTOR

MAIN CABINET

PTV BASE

ACCELERATOR CONTROL PANEL.

COIN CHUTE DOOR’

CASHBOX DOOR|

FIG. 4b

TABLE 4

WidthX = LengthX = HeightWeight
PROJECTOR(PTV)1140mmX555mmX_1,670mm112 kg
PTV BASE1160mmX545mmX235mm28 kg
BILLBOARD1140mmX400mmX410mm19 kg
MAIN CABINET1140mmX2,080mmX_1,590mm300 kg
When assembled1,310mmX2,610mmX = 2,230mm450 kg
Page 14
  • ACCESSORIES

When transporting the machine, make sure that the following parts are supplied.

TABLE 5 ACCESSORIES

DESCRIPTION OWNERS MANUAL Part No. (Qty.) 420-6588-01 (1)

Note

Figures If Part No. has no description, the Number has not been registered or can not be registered. Such a part may not be obtainable even if the customer desires to purchase it. Therefore, ensure that the part is in safekeeping with you.

TAMPERPROOF WRENCH MB8 540-0009-01 (1) TOOL KEY MASTER KEY 220-5576 (2) (2) For opening/closing For the CASHBOX DOOR the doors

The Keys are inside the Coin Chute Door at the time of shipment from the factory.

AC Cable (Power Cord) 600-7228 (1) TAIWAN 600-6695 (1) USA 600-6618 (1) OTHERS 600-6619 (1) HONG KONG Used for installation, of Section 6.

Page 15

TOSHIBA Remote Controller used for adjustment of the projector. See Section 14. 200-5536(1)

One of the above 3 types of Remote Controllers is used for the Projector. MITSUBISHI Remote Controller used for adjustment of the projector. See Section 14. 200-5532(1)

The Remote Controller is attached to the Projector at the time of shipment.

CARTON BOX 601-10642 (1) Used for transporting the Game Board. Refer to Next Page. FLEX TUBE 310-5050-220200 (1) For communication play, refer to Section 20.

ASSY FIBER CABLE 600-6275-0500 (1) For communication play, refer to Section 20.

CONN 22 310-5051-22 (2) For communication play, refer to Section 20.

Page 16

HOW TO USE THE CARTON BOX

@ When asking for the replacement or repair of the product's Game Board (NAOMI 2), be sure to put the Game Board together with the Shield Case in a Carton Box. Otherwise, the request is not acceptable. Put the Shield Case in the Carton Box by paying attention to the correct direction as per the following instructions and as shown by the instructions printed on the Carton Box. Handling in an erroneous manner can damage the Game Board. Remove the Shield Case Brackets from the Shield Case and put the Shield Case in the Carton Box.

SHIELD CASE BRACKETS ‘The shape depends on the type of product. "CHECK SIDE" Display

Wrap the Shield Case with the packing material and put it in the Carton Box as shown. Putting it upside down or packing otherwise in the manner not shown can damage the Game Board and parts.

Page 17
  • ASSEMBLING AND INSTALLATION
WARNING!

A

CAUTION! Perform assembly work by following the procedure herein stated. Failing to comply with the instructions can cause electric shock hazard. Perform assembling as per this manual. Since this is a complex machine, erroneous assembling can cause an electric shock, machine damage and or not functioning as per specified performance. When assembling, be sure to use plural persons. Depending on the assembly work, there are some cases in which working by one person alone can cause personal injury or parts damage. Ensure that connectors are accurately connected. Incomplete connections can cause electric shock hazard. Be careful so as not to damage wirings. Damaged wiring can cause electric shock and short circuit hazards. Do not carelessly push the PTV. Pushing the PTV carelessly can cause the PTV to fall down. This work should be performed by the Location's Maintenance Man or Serviceman. Performing work by non-technical personnel can cause a severe accident such as electric shock. Failing to comply with this instruction can cause a severe accident such as electric shock to the player during operation. Provide sufficient space so that assembling can be performed. Performing work in places with narrow space or low ceiling may cause an accident and assembly work to be difficult. To perform work safely and avoid serious accident such as the cabinet's falling down, do not perform work in places where step-like grade differences, a ditch, or slope exist. Carefully handle the PTV on the PTV base because it is very unstable. If handled carelessly, it may fall down and eventually cause a serious personal injury.

To perform work safely and securely, be sure to prepare a step which is in a secure and stable condition. Performing work without using the step can cause violent falling down accidents.

Page 18

When carrying out the assembling and installation, follow the following 6-item sequence.

ASSEMBLING THE PTV

COUPLING THE MAIN CABINET TO THE PTV

SECURING IN PLACE (ADJUSTER ADJUSTMENT)

POWER SUPPLY CONNECTION

TURNING POWER ON oy] [ey] fs] [eu] [No] IN

ASSEMBLING CHECK

The master key (accessories) in addition to the tools such as a Phillips type screwdriver, wrench, socket wrench and Ratchet Handle are required for the assembly work.

Phillips type screwdriver

SOCKET WRENCH,(MB hexagon bolt) RATCHET HANDLE

Oo KEY MASTER

Page 19

ASSEMBLING THE PTV

® Fix the two mask holders onto the PTV top panel each with the 2 countersunk-head screws.

@ Insert and raise the TV mask as illustrated below, and fix it with the 6 screws.

  • Fix the panel-mounting brackets L and R onto the PTV front each with the 2 screws.
  • Mount the front panel onto the PTV front. Fix it with the 4 trusshead screws.

FLAT HEAD SCREW (2 each) i / Ma X12

MASK HOLDER:

~

TV MASK

TRUSS SCREW(2) black M5 X 25, flat washer used.

_PANEL MOUNT BRACKET L

~~_SCREW (2 each) /SCREW (4) M5 X 16, wiflat & spring washers M5 X 20, w/flat & spring washers : PANEL MOUNT BRACKET R

\ \rront PANEL.

TRUSS SCREW(4) blac! M5 X 25, flat washer us FIG. 6. 1a

Place the PTV on the PTV base. Minimum 3 workers must engage in lifting the PTV while several other works must hold the PTV base.

When lifting the PTV the minimum 3 workers must cooperate. FIG. 6. 1b

Page 20

© Connect the billboard wire's two connectors to the PTV top panel's connectors. For the safety the 2 workers must hold the billboard while another worker must use a stool when connecting.

SCREW (2) _ M5 X 16, w/flat & spring wa

@ Place the billboard on the

PTV top panel. Engaging the billboard on the 2 mask holders, slide it to the PTV front. Be careful not to damage the wires in this instance. BILLBOARD

@ Fix the billboard with the

2 screws.

PTV BASE

FIG. 6. 1¢

When performing work, be sure to use a step.

FIG. 6. 1d

Page 21

2] COUPLING THE MAIN CABINET TO THE PTV

® Move the main cabinet and the PTV closer to each other. Carefully move the PTV on the PTV base because it is unstable.

@Take out the 2 wires from the main cabinet; one for the video signals and another for the power.

® Connect the wires between the main

cabinet and the PTV. The connector panel of the PTV front provides two connectors. Into them, insert the 2 wire connectors from the main cabinet; one for the video signals and another for the power. Each has an insertion direction. Make sure about the insertion direction before inserting the connectors, and do not apply excessive force when inserting; otherwise they may be damaged. The connector for the video signals has two fixing screws at its both ends. Tightly fasten them after inserting the connector. PHOTO 6. 2a

MITSUBISHI PROJECTOR

Fasten the screws,

Fasten the screws.

Page 22

@Remove the 3 trusshead screws to detach

the mechanism-side lid from the main cabinet. A square hole appears.

© Couple the PTV and the main cabinet

with each other. Before attaching them closely without a gap, insert a hand into the square hole and pull the 2 wires into the main cabinet. This will prevent the wires from being caught between them.

PHOTO6. 2b

© Mount the 2 joint bracket centers onto the PTV and the main cabinet. Fix them each with 4 hexagonal-head bolts.

@ Mount the 2 joint bracket onto the PTV base and the main cabinet. Fix them each with 3 hexagonal-head bolts.

@®)Replace the mechanism-side lid to the main cabinet and fix it with the 3 trusshead screws.

FIG. 6.2b JOINT BRACKET PTV BASE

Page 23

INSTALLING THE POP

@ Peel off the double-sided adhesive tape on the POP reverse and stick the POP Holder.

@ By using the 3 Truss screws, secure the POP Holder to the Billboard ceiling.

POP HOLDER

POP. Height:320mm

Ne SCREW (3) black

M4X8

Double-sided adhesive tape, “

FIG. 6.2¢

Page 24

EE SECURING IN PLACE (ADJUSTER ADJUSTMENT)

Make sure that all of the adjusters are in contact with the floor. If they are not, the cabinet can move and cause an accident.

WARNING! This product has 10 casters (4 for PTV base, 6 for Main Cabinet) and 10 Adjusters (4 for PTV base, 6 for Main Cabinet). (FIG. 6. 3a) When the installation position is determined, cause the adjusters to come into contact with the floor directly, make adjustments in a manner so that the casters will be raised approximately 5mm. from the floor and make sure that the machine position is level.

® Transport the product to the

installation position. Be sure to CASTER provide adequate space allowing the player to get on and off.

@ Have all of the Adjusters make eX oe = a

contact with the floor. Adjust the fo) Adjuster's height by using a [| wrench so that the machine position is kept level. . . =) @afier making adjustment, fasten e 5 @) 23 the Adjuster Nut upward and ee secure the height of Adjuster (FIG. 6. 3 b). ADJUSTER

ADJUSTER FIG. 6.3 a BOTTOM VIEW

D CASTER,

FASTEN UPWARD, lI °

a) | Approx.5mm FIG. 6.3 b ADJUSTER \ apruster 10cm over |

2.8m

FIG. 6.3¢ Refer to this Fig. (Scale:1/100) FIG. 6.3d

for the layout of the place of Be sure to provide space as shown between

installation. the Air Vent and the wall surface.

Page 25

Z| POWER SUPPLY

Be sure to independently use the power supply socket outlet equipped with an Earth Leakage Breaker. Using a power supply without an Earth Leakage Breaker can cause a fire when electric leakage occurs. Ensure that the "accurately grounded indoor earth terminal" and the earth wire cable are available (except in the case where a power cord plug with earth is used). This product is equipped with the earth terminal. Connect the earth terminal and the indoor earth terminal with the prepared cable. If the grounding work is not performed appropriately, customers can be subjected to an electric shock, and the product's functioning may not be stable. Ensure that the power cord and earth wire are not exposed on the surface (passage, etc.). If exposed, they can be caught and are susceptible to damage. If damaged, the cord and wire can cause electric shock and short circuit accidents. Ensure that the wiring position is not in the customer's passage way or the wiring has protective covering. After wiring power cord on the floor, be sure to protect the power cord. Exposed power cord is susceptible to damage and causes an electric shock accident.

WARNING!

The AC Unit is mounted on the right side of the machine. The AC Unit has Main SW, Circuit Protector, Earth Terminal and the Inlet which connects the Power Cord.

® Ensure that the Main SW is OFF.

ot ea) . 5) |

  • | | : | = . | MAIN SW ad

0 INLET

i a]

Main SW off 1h FIG. 6.4 AC unit fi

AC Cable (Power Cord) | tTb+ y)

Page 26

HOW TO USE THE CORD CLAMP In case the Power Plug is apt to come out of place, secure the Power Cord to the periphery of the AC Unit with the Cord Clamp (an accessory).

Page 27

[ 5] TURNING POWER ON

Connect the power by turning on the AC unit's main switch. Then the billboard's fluorescent light comes on. The monitor (PTV screen) displays a system power-on message, and then an advertising screen (a plying-for-hire screen) appears. At the same time the right and left speakers on the control panel output an advertise sound. The sound is inaudible, however, when you have disabled its function. Before an advertising screen appears the system automatically conducts an initialization. Do not touch the product until the system completes an initialization and the advertising screen appears. During an initialization the handle (steering wheel) turns counterclockwise and clockwise and stops at the original center position (for a straight-ahead direction). This corrects the volume value inside the control panel. Do not touch the handle or play the game before an initialization is completed (that is, the handle automatically stops at the center position). Failure to observe this may affect the handle's operability and the handle's force feedback (force feedback against crashing) during playing the game. If the handle's operability or force feedback is abnormal, disconnect and reconnect the power for initializing the system again. When you disconnect the power, the system saves the data for the credit number, ranking, and latest game's score. Assume that the credits effective for playing a game remain when you disconnect the power. In this case, when you will reconnect the power a game startup screen will appear with the start button flashing. If several machines are interconnected or networked for a communication play, the system checks the network. A network-checking screen as illustrated below appears before an advertising screen appears. Usually, checking the network takes 1 to 3 minutes. If the system detects a problem related with the network, it keeps displaying the network-checking screen or an error message.

Fluorescent lamps are always lit.

Move MASTER XXXX x STATUS: XXXX CHECKING NETWORK On-screen images are outputted.

Handle turns counterclockwise and clockwise.

FIG. 6.5 b NETWORK check screen

Sound is emitted.

Page 28

6 ASSEMBLING CHECK

In the TEST MODE, ascertain that the assembly has been made correctly and IC BD. is satisfactory (refer to Section 9). In the test mode, perform the following test:

  • MEMORY TEST

RAM TEST

ICIS IC16 IC17S IC188 GOOD 1C22 1€23 1C24S8 1258 GOOD 1C28 C298 Goop Ic4l GooD 1c42 GooD IC44 IC45S 1C46 IC478. GOOD Ic91s 1¢928 GooD Ico8 GooD

OPTIONAL SOUND BOARD: 1c2 GooD

OPTIONAL COMMUNICATION BOARD: ICT IC8 IC9 IC10 GOOD

PRESS TEST BUTTON TO EXIT

  • C.R.T. TEST

C.R.T. TEST PAGE#1

RED

GREEN

BLUE

WHITE

PRESS SERVICE BUTTON TO ANOTHER PAGE PRESS TEST BUTTON TO EXIT

PAGE#2

RESS SERVICE BUTTON TO ANOTHER PAGE PRESS TEST BUTTON TO EXIT U Selecting the RAM TEST on the system test mode menu screen causes the on-board memory to be tested automatically. The game board is satisfactory if the display beside each IC No. shows GOOD.

In the system test mode menu, selecting C.R.T. TEST allows the screen (on which the monitor is tested) to be displayed. Although the monitor adjustments have been made at the time of shipment from the factory, color deviation, etc., may occur due to the effect caused by geomagnetism, the location building's steel frames and other game machines in the periphery. By watching the test mode screen, make judgment as to whether an adjustment is needed. If it is necessary, adjust the monitor by referring to Section 13.

Page 29
  • SOUND TEST

SOUND TEST

MAIN SPEAKER LEFT MAIN SPEAKER RIGH" OPTION SPEAKER LE! OPTION SPEAKER RIGHT > EXIT

SELECT WITH SERVICE BUT AND PRESS TEST BUTTON

  • INPUT TEST

INPUT TEST

STEERING WHEEL XXX GAS PEDAL XXX BRAKE PEDAL XXX GEAR POSITION ON START BUTTON OFF VIEW CHANGE BUTTON OFF

SERVICE SWITCH OFF TEST SWITCH OFF

PRESS TEST AND SERVICE BUTTON TO EXIT

JVS TEST > DISPLAY CONFIG EXIT

NODE 1/1 SWITCH SYSTEM _ PLAYER _ PLAYER2 _ COIN SLOT1 0000 SLOT2 8000 ANALOG CH1 0000 CH2 0000 CH3 0000 CH4 0000 CHS 0000 CH6 0000 CH7 0000 CH8 0000

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON In the system test mode, selecting SOUND TEST causes the screen (on which sound related BD and wiring connections are tested) to be displayed. Check if the sound is satisfactorily emitted from each speaker and the sound volume is appropriate.

Selecting the INPUT TEST on the game test mode menu screen causes the screen (on which each switch is tested) to be displayed. Press each switch. For the coin switch test, insert a coin from the coin inlet with the coin chute door open. If the display beside each switch indicates "ON," the switch and wiring connections are satisfactory.

Page 30
  • OUTPUT TEST

Select OUTPUT TEST from the Menu screen in the Game Test Mode to cause the OUTPUT TEST screen (on which output unit such as lamps > START BUTTON and wiring connections are tested) to appear. VIEW CHANGE BUTTON Ensure that the output unit functions BASS SHAKER(FRON' satisfactorily. BASS SHAKER(FRONT+REAR)

PRESS TEST BUTTON TO EXIT

Perform the above inspections also at the time of monthly inspection.

Page 31
  • PRECAUTIONS TO BE HEEDED WHEN MOVING THE MACHINE
WARNING!

A

CAUTION!
IMPORTANT When moving the machine, be sure to unplug the power plug. Moving the machine with the plug as is inserted can damage the power cord and cause fire and electric shock hazards. When moving the machine on the floor, retract the Adjusters and ensure that Casters make contact with the floor. During transportation, pay careful attention so that Casters do not tread power cords and earth wires. Damaging the power cords can cause electric shock and short circuit hazards. When lifting the cabinet, be sure to hold the grip portions or bottom part. Lifting the cabinet by holding other portions can damage parts and installation portions due to the empty weight of the cabinet, and cause personal injury. en transporting the product in places with step-like differences in grade, isassemble into each unit before transporting. Lifting up the product in an attempt to cross the step-like differences in an as is assembled condition may lamage the unit's joining portions and cause a personal injury resulting from jamage. When moving the PTV, do not push it from the rear side. Push it from sideways. Pushing the PTV from the rear side can have the PTV fall down, causing personal injury etc. In case the floor has slanted surfaces or step-like ifferences, be sure to move the machine by 2 or more persons. Do not insert the fork to places other than designated when using a Forklift to transport the machine. Failure to observe this could cause falling down and injury resulting from falling down. Carefully handle the PTV on the PTV base because it is very unstable. If handled carelessly, it may fall down and eventually cause a serious personal injury.

Do not push the plastic made parts. Failure to observe this may damage parts and cause injury due to fragments resulting from damage. Do not use the handle or lever to move the product. Failure to observe this may cause the parts to be deformed or damaged.

When transporting the product in places with steps, disassemble into each unit before transporting. Inclining the product in an as is assembled condition or placing the cabinet in places with steps can damage the unit's joining portions. To protect surface, do not directly apply a rope to the surfaces of product. Use protective materials to the places the rope is applied to.

Page 32

Do not push PTV from the back. Pushing the PTV from the back can cause the PTV to fall down. Push it from the side.

On level surfaces,move the machine by causing the Casters to make contact with the surfaces.

When transporting the product in places with steps or step-like differences in grade, disassemble into each unit before transporting.

Page 33

When moving the product, use its recessions and bottom parts. Do not hold or push the illustrated parts to move the product.

SCREEN,TV MASK

HANDLE

The PTV on the PTV base is very unstable.

Page 34
  • CONTENTS OF GAME

The following explanations apply to the case the product is functioning satisfactorily. Should there be any moves different from the following contents, some sort of faults may have occurred. Immediately look into the cause of the fault and eliminate the cause thereof to ensure satisfactory operation.

Advertising (Plying-for-Hire) Performance

The billboard's fluorescent light is always on when the power is connected. The monitor displays the demonstration images and ranking data. The ranking data is updated every week. The lights (integrated with the two buttons on the control panel) are off. The right and left speakers on the control panel output an advertise sound. The right and left speakers on the seat backrest and the bass shaker do not output an advertise sound. You can activate or deactivate an advertise sound output function on the test mode screen.

Fluorescent lamps are lit.

Image output on the monitor.

Emits sounds.

Page 35

HOW TO PLAY

Operation of a single machine allows a Single Play. Operation of interconnected machines allows a Communication Play. VIEW CHANGE BUTTON

START BUTTON STEERING WHEEL

HANDLE

BRAKE PEDAL 4 GAS (ACCELLETOR) PEDAL

SEAT LOCK LEVER

FIG. 8b

[Single Play]

In this game, the players make their karts and enter the race for competing with each other. (00 you want to make your original kart? Your original kart Is made.

By achieving a good score in the Championship Race mode, you can step up from “Class Novice” (at start) to “Class B,” “Class A,” and “Class S.” When you step up to a higher class, you may get an extended course along which you can drive, or the performance of the kart with your character may vary. The goal is to win in the race in the environment that may vary in such a manner. By selecting “Practice Race,” you can select and run along the course for a series of races, if you desire.

This game allows the data to be retained through the cards system. In addition to the kart’s name, frame, cowl, suits, helmet, etc., information such as the total time, achievements in a series of races, the highest rank by class can be recorded on the “Club Kart Card” (hereafter “CARD”).

Page 36

How to Play the Game --- If you play the Championship Race for the first time:

+ Throw coins into the slot. At this time, the value converted for the number of credits is displayed at the bottom right corner of the screen. JDo you have the [club kart CARD]? When you throw into the slot the number of coins enabling operation of one play session, you go to the screen that asks whether you have a card. + In response to the inquiry, “Do you want to create a new card?” + If you answer with “NO,” or you do not insert any card after you answer with “YES,” Rental Kart is automatically selected as the type of the kart you can luse. In this case, you go to Step | (creating a new card). One more credit is required in this case. + If you throw a card into the slot without making the selection, you will go to selection of the Race Mode.

Rental Kart Mode

In the Rental Kart Mode, you select and run along the desired one of four courses for competition in lap time. You choose either one of two types of karts: for the novice and middle classes. You are required to make the specified number of circuits of the course within the predetermined time-out time. + Once you complete the first circuit, the remaining time of the time-out time for the first circuit is added to the time-out time for the second circuit. + When you complete the specified number of circuits of the course within the specified time, the finish takes place. When the time-out time reaches 0, Game Over takes place. An example where “YES” was selected is described in this document.

Page 37

+ Create a new card. After entering the name, select the cowl, frame, and racing suite colors and the helmet design according to the instructions on the screen.

Dexter your name.

. _—s B1)8)'3) 4) 56 17 (6S Bl +

Pus in your Wierd cus kart CARD which has aiready orgincied a team. The eyeten wil recone the tear) seta Set you On a Nw oare.

+ After you have entered all the information, you go to the confirmation screen and must make operations according to the instructions on the screen.

+ Select the Race Mode. You can choose either Championship Race or Practice Race. (“Communicated Race” is additionally displayed when two or more machines are interconnected.) Turn the = Championship race —_ steering wheel clockwise or counterclockwise Gass Novice OT" lowold BO for selection. Then, determine the selection ——_ by pressing the accelerator pedal. Practice race.

Page 38

Championship Race

+ In this mode, you compete with the other players for the total achievement of a Series of Races that are done, depending on four classes (Novice, B, A, and S). The race in this mode begins after you have created the feature of creating your own original kart (one of the distinctive features of this game) and the card to save the running record. With the card, you can save the data before completion of the series of races; at the next play time, you can resume the game from the ending point in the previous session of the game.

Practice Race

You can select and run along the desired one of the courses along which you run in a Series of Races. The number of courses from among which can select depends on the number of racces included in the series, which varies with the class to which you belong (4 of Novice, 6 for B, 8 for Class, and 10 for S).

+ Information about the player’s kart (class, the number fo times won and defeated, the top ranking, the best time, the number of races in the series, etc.) and the course map are displayed before the race starts. When you created a card for the first time, the player’s kart starts at the rearmost position. You are required to make the specified number of circuits of the course within the predetermined time-out time. Once you complete the first circuit, the remaining time of the time-out time for the first circuit is added to the time-out time for the second circuit.When you complete the specified number of circuits of the course within the specified time, the finish takes place. When the time-out time reaches 0, Game Over takes place. + If your kart touches the wall of the course or another kart or goes outside the course while the game is in progress, you feel a reaction through the steering wheel. + While the game is in progress, pressing the Viewpoint Change button changes the viewpoint on the screen. The button is continually flashing while the game is in progress. + While the game is in progress, pressing the Start button toggles between the map that shows the player kart’s and the time display that indicates the other karts’ positions and the best time in the class and that of your records.

+ After each race is completed, the Results Screen appears if you have run along the whole course. After the Results Screen appears, the Select Sponsor Screen may appear, depending on the results of the series of races. The number of sponsors, at random, increases or decreases, depending on the achievement. The logo of the sponsor you selected can be attended to the kart if you desire this.

When Select Sponsor Screen appears for the first timc, RII IZ 7 77 7 _7_ 77: you assign the team name to your kart. O)Selact a Sponsor

Page 39

+ Fora Series of Races, the total achievements are listed when the predetermined number of races have been completed for each of the classes. If you have established good achievement, a screen appears that lets you select You definitely need to move up to whether to try the next series of races at the \é the next class the next time you race. current or upper class. (iEnd of Series.

A tremendous result".

Next Series = B |

+ Ifthe Practice Race Mode is entered or all the credits have been exhausted after the data is written onto the card after completion, Game Over takes place. If you are in the Championship Race Mode, you go to the Continue Screen. If you still have credits for one or more play sessions at this time in the Championship Race Mode, you can go to the next course and enjoy one or more play sessions after jumping to the course map display is Step ???.

Page 40

[Communicated Play]

Communicated Play differs slightly from Single Play regarding the game starting procedure and how to play the game.

+ When coins you throw into the slot the coins with which you can enjoy a play session, the Entry Screen appears and, at the same time, the Start button begins to flash.

+ If you desire a competitive play, throw the appropriate number of coins into the slot at another seat. If you desire the single play mode, press the Start button immediately after the Entry Screen appears.

  • Once the Entry Screen appears, a countdown starts. If a person who desires to compete with you does not appear before the count reaches 0 (zero), you have to enjoy the game in the Single Play Mode.

+ Once the count in the Entry Screen reaches 0, you are brought to the Select Rental Kart Screen. Turn the steering wheel clockwise or counterclockwise to choose selection by pressing the accelerator pedal and Start button. If you have a card, you will be subsequently able to use your own original kart by inserting the card into the slot. The course assignments to the players are determined by majority of the players.

+ Once the course assignments are determined, information about the players’ karts (class, the number of times won and defeated, the top ranking, the best time, the number of races in the series, etc.) and the course map are displayed before the race starts.

+ In the race, the players compete with each other for their ranks. Each time the first-rank player completes one circuit of the course, the time that remained is added to that of the next circuit of the course. When you complete the specified number of circuits of the course within the specified time, the finish takes place. When the time-out time reaches 0, Game Over takes place.

+ STEERING DIR This is a setting about the cabinet. Basically, you do not need to change it. You should use the factoryadjusted setting.

+ CARD SYSTEM This sets the mode of operation for the card system unit. For usual operation, set ENABLE. If the card system unit is detached from the system, set DISABLE.

+ BONUS GAMES This sets the count of plays given as a bonus when a new card is created. By setting this, the count can be set to 0 to 3 times.

Page 41

9, EXPLANATION OF TEST AND DATA DISPLAY

By operating the switch unit, periodically perform the tests and data check. When installing the machine initially or collecting cash, or when the machine does not function correctly, perform checking in accordance with the explanations given in this section. The following shows tests and modes that should be utilized as applicable. SEGA HIKARU GAME BOARD is used for the product. The system of this game board allows another game to be played by replacing the ROM Board Case mounted on the SEGA. HIKARU CASE. As such, the Test Mode of this system consists of the System Test Mode for the system to execute SELF-TEST, COIN ASSIGNMENTS, ete. used in common for the machines employing the SEGA HIKARU BOARD, and the Game Test Mode for the specific product to execute Input/Output test for the operation equipment, difficulty setting, etc.

The contents of settings changed in the TEST mode are stored when the test mode is finished from EXIT in the menu mode. If the power is turned off before the TEST mode is finished, the contents of setting change become ineffective. Executing "BACKUP DATA CLEAR" in the SYSTEM TEST MODE does not clear the BOOKKEEPING data in the GAME TEST mode. Entering the TEST mode clears fractional number of coins less than one credit and BONUS ADDER data. When the 2 or more machines are linked for communication play, be careful to enter the test mode. If one of the machines linked enters the test mode, all others display the NETWORK CHECK screen.

Page 42

TABLE 9 EXPLANATION OF TEST MODE REFERENCE

ITEMS DESCRIPTION EN

INSTALLATION | When the machine is installed, perform the following: OF MACHINE 1. Check to see that each setting is as per standard setting made at | 9-2 F,G, 9-3 F the time of shipment.

  • In the INPUT TEST mode, check such input devices as each 9-2 C, 9-3 B SW, V.R., etc.
  • In the OUTPUT TEST mode, check such output devices as 9-3C lamps, motors, etc.
  • In the SELF-TEST mode, check ICs on the IC Board. 9-2 BJ
MEMORYChoose MEMORY TEST in the MENU mode to allow the9-2 BJ

MEMORY test to be performed. In this test, PROGRAM RAMs, ROMs, and ICs on the IC Board are checked.

PERIODIC Periodically perform the following:

SERVICING1. MEMORY TEST9-2 BJ
  • Ascertain each setting. 9-2 F,G, 9-3 F
  • In the INPUT TEST mode, test the CONTROL device 9-2 C, 9-3 B
  • In the OUTPUT TEST mode, check such output devices as 9-3C lamps, motors, etc.
CONTROL1. In the INPUT TEST mode, check such input devices as each9-2 C, 9-3 B

SYSTEM SW, V.R., etc.

  • Adjust or replace each SW and VR. 9-3 D,E,
  • If the problem can not be solved yet, check the CONTROL's 10,11,12 moves.
MONITORIn the MONITOR ADJUSTMENT mode,9-2E

check to see if the PROJECTOR adjustment is appropriately 13 made.

IC BOARD1. MEMORY TEST9-2 BJ
  • In the SOUND TEST mode, check the sound related ROMs. 9-2D
DATA CHECKCheck such data as game play time and histogram to adjust the9-2 H, 9-3 G

difficulty level, etc.

Page 43

9-1 SWITCH UNIT AND COIN METER

@ Adjust to the optimum sound volume by considering the environmental requirements of the installation location. @ [Ifthe COIN METER and the game board are electrically disconnected, game play is not possible.

@ A cover is provided on the bass shaker output adjustment volume in order to

prevent the BASE SHAKER against being carelessly adjusted.

SWITCH UNIT

Open the coin chute door, and the switch unit shown will appear. The functioning of each SW is as follows: The sound volumes of the front and rear speakers are adjusted as indicated by the illustration on the switch unit, at the factory before shipping. This adjustment aims to attain the best output balance between the front and rear speakers. Remember that carelessly changing this adjustment may cause the best balance to be lost.

COIN METER

PUSH BUTTON Test SERVICE

  • REAR SPKR. FRONT SPKR °

SOUND VOLUME

FIG. 9. 1a SWITCH UNIT

Page 44

TEST BUTTON : For the handling of the test button, refer to the following pages. TEST SERVICE BUTTON : Gives credits without registering on the coin meter. SERVICE SOUND VOLUME : Adjusts the sound volume of the left and right speakers on the control panel. FRONT SPEAKER SOUND VOLUME : Adjusts the sound volume of the left and right speakers on the seat backrest. REAR SPEAKER BASE SHAKER Output Adjustment Volume —: Adjusts the vibration output of the base shakers each on BASS SHEAKER the seat backrest and the control panel.

COIN METER

Open the Cashbox Door by using the key to have the Coin Meter appear underneath the Cashbox.

COIN METER,

FIG. 9. 1 b COIN METER

Page 45

9-2 SYSTEM TEST MODE

The contents of setting changes in SYSTEM ASSIGNMENTS, COIN ASSIGNMENTS, and GAME TEST MODE are stored when the test mode is EXITed. Ifthe power is turned off before EXITing, the contents of setting

IMPORTANT changes are ineffective. Be very careful of this point.

This test mode mainly allows the IC Board to be checked for accurate functioning, monitor color to be adjusted as well as COIN ASSIGNMENTS and GAME ASSIGNMENTS to be adjusted.

TEST ITEM SELECT

@) After turning power on, press the TEST button to have the following test item menu displayed.

SYSTEM MENU

RAM TEST JVS TEST SOUND TEST C.R.T. TEST SYSTEM ASSIGNMENTS COIN ASSIGNMENTS BOOKKEEPING BACKUP DATA CLEAR CLOCK SETTING

ROM BOARD TEST GAME TEST MODE [XXXXXXXXXXXXXXX]

-> EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

@ Press the SERVICE button to move the arrow. Bring the arrow to the desired item and press the TEST button.

® Upon finishing the test, bring the arrow to EXIT and press the TEST button to return to the Game mode.

Page 46

A. RAM TEST

This allows for checking the functioning of the RAM on the NAOMI 2 Main BD. "GOOD" is displayed for satisfactory RAMs, and "BAD" is indicated for irregular RAMs, if any.

1C29 GOOD 1C35 GOOD 1c09 GOOD IC11 GOOD IC16 GOOD 1C20 GOOD 1C17 GOOD 1C21 GOOD 1C106 GOOD 1C108 GOOD 1IC111 GOOD 1C115 GOOD 1C112 GOOD 1C116 GOOD RAM TEST

TESTING NOW

1C10 GOOD 1C12 GOOD IC18 GOOD 1C22 GOOD 1C19 GOOD 1C23 GOOD 1C107 GOOD IC109 GOOD 1C113 GOOD IC117 GOOD IC114 GOOD IC118 GOOD

PRESS TEST BUTTON TO EXIT

"TESTING NOW" shows up (flashing) on the screen during the test. Returns to the menu screen when the TEST button is pressed after the test is over.

Page 47

B. JVS TEST

In this test, Specifications of the I/O Board connected to NAOMI 2 can be checked, and INPUT TEST can be performed. First, I/O Board Specifications are displayed.

JVS TEST INPUT TEST NEXT NODE -> EXIT NODE V/1 NAME SEGA ENTERPRISES,LTD. VO BD JVS 837-13551 Ver 1.00 CMD VER 1.1 JVS VER 2.0 COM VER 1.0 SWITCH 2PLAYER(S) 13BITS COIN 2SLOT ANALOG 8CH ROTARY 0CH KEYCODE 0 SCREEN X:0 Y:0 CH:0 CARD OSLOT HOPPER OUT 0CH DRIVER OUT 6SLOT ANALOG OUT 0CH CHARACTER CHARA:0 LINE:0 BACKUP 0

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON (A) (B) ©)

” «Name and version of I/O BOARD.

Select with the SERVICE button and press the TEST button.

(A)INPUTTEST:Proceeds to the INPUT TEST of I/O BOARD being displayed.
(B)NEXTNODE :In the case where more than 2 I/O Boards are connected, proceeds to

the next I/O Board.

(C)EXIT:Returns to the menu mode.

INPUT TEST SCREEN

JVS TEST INPUT TEST NEXT NODE -> EXIT

NODE 1/1

SWITC! SYSTEM 00000000 PLAYERI 00000000 00000000 PLAYER2 00000000 00000000 COIN 1 §—- When INPUT is performed for the switches of Control Panel, etc., the value changes to 1 from 0.

0000 0000 ANALOG—W_, 0000 0000 0000 0000 0000 0000 0000 0000 p> If the Coin SW is inputted, the count starts. When the TEST MODE is finished, the count is cleared and returned to[0000].

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON p> Analogue values are displayed between 0000 and FFOO.

Page 48

C. SOUND TEST

Sound Output test can be performed. Beep sounds can be emitted from each of left/right Speakers.

SOUND TEST

RIGHT SPEAKER OFF — Enmitted from the right-hand side Speaker. LEFT SPEAKER OFF — Enmitted from the left-hand side Speaker. -> EXIT — Returns to the menu mode.

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

D. C.R.T. TEST

  • RGB COLOR ADJUSTMENT SCREEN In this page, monitor color can be checked.

C.R.T. TEST 1/2 Each of red, green, and blue is the darkest at the 1 32 leftmost end, and becomes brighter towards the right-hand end in 31 gradations. Monitor RED brightness is satisfactory if the white color bar GREEN is black at the left end and if it is white at the right end. BLUE Press the TEST button to proceed to the next WHITE page.

PRESS TEST BUTTON TO CONTINUE

  • MONITOR SIZE ADJUSTMENT SCREEN In this page, monitor size can be checked.

C.R.1 EST 2/2 Adjust so that the checkered patterns do not go beyond the screen. Press the TEST button to return to the menu mode.

RESS TEST BUTTON TO EXIT +-

Page 49

E. SYSTEM ASSIGNMENTS

The settings of cabinet and board can be changed. Game related assignments such as game difficulty, etc. are performed in K. GAME TEST MODE.

® Press the SERVICE button to move the arrow. Bring the arrow to the desired item.

@ Press the TEST button to change the setting.

® Upon finishing the setting, move the arrow to EXIT and press the TEST button.

SYSTEM ASSIGNMENTS,

CABINET TYPE1PLAYER(S)(A)

ADVERTISE SOUND ON (B)

MONITOR TYPEHORIZONTAL](C)
SERVICE TYPECOMMON(D)

-> EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

(A) CABINET TYPE (IPLAYER(S), 2PLAYER(S), 3PLAYER(S), 4PLAYER(S)) Sets the number of players between | and 4. Fix setting to 1 PLAYER(S).

(B) ADVERTISE SOUND (ON, OFF) Sets whether ADVERTISE sound is to be emitted or not.

(C) MONITOR TYPE (HORIZONTAL, VERTICAL) Sets the on-screen display to the positional direction of monitor (HORIZONTAL/VERTICAL) Fix setting to HORIZONTAL. HORIZONTAL: Normal on-screen display VERTICAL: On-screen display when the monitor is vertically positioned as against normal HORIZONTAL position.

(D) SERVICE TYPE (COMMON, INDIVIDUAL) Sets the functioning of when the SERVICE button is pressed, in case that several SERVICE buttons exist. Fix setting to COMMON. COMMON: By pressing any SERVICE button, Service credit can be obtained for all Players. INDIVIDUAL: _ By pressing SERVICE button, Service credit can be obtained for the Player corresponding to the SERVICE button pressed.

Page 50

F. COIN ASSIGNMENTS

In this mode, the setting of incremental credit increase as against coin insertion can be changed.

® Press the SERVICE button to move the arrow. Bring the arrow to the desired item.

@ Press the TEST button to change the setting.

@Upon finishing the setting, bring the arrow to EXIT and press the TEST button.

COIN ASSIGNMENTS

MANUAL SETTING SEQUENCE SETTING ->EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON COIN ASSIGNMENTS

COIN CHUTE TYPE COMMON (A) COIN CHUTE TYPE INDIVIDUAL COIN/CREDIT SETTING #1 (B) COIN/CREDIT SETTING #1 COIN CHUTE #1 COIN CHUTE #1 1 COIN 1 CREDIT 1 COIN 1 CREDIT

COIN CHUTE #2 1 COIN 1 CREDIT © (G) MANUAL SETTING SEQUENCE SETTING ->EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

Setting to COMMON

(A) COIN CHUTE TYPE (COMMON, INDIVIDUAL) Fix setting to COMMON.

COMMON Setting to INDIVIDUAL

This setting is for the cabinet which has a coin chute(s) for common use by plural players. Up to 2 Coin Chutes (#1 and #2) can be used and also, (B) COIN/CREDIT SETTING ratio can be set separately for #1 and #2.

INDIVIDUAL This setting is for the cabinet in which each player uses an independent coin chute. Coins inserted by each player are handled as the player's credits. Depending on the CABINET TYPE setting in the SYSTEM ASSIGNMENTS and the functioning of the connected I/O Board, the number of Coin SW INPUT ports varies between | and 4. (B) COIN/CREDIT SETTING ratio is common for eath Coin Chute.

(B) COIN/CREDIT SETTING (#1 ~# 27) Sets the credit increase increment per coin insertion. There are 27 settings from #1 to #27, expressed in © © credit(s) as against © © coins inserted. #27 refers to FREE PLAY. For details, refer to Table 1 (COMMON) and Table 2 (INDIVIDUAL).

Page 51

(C) MANUAL SETTING The Credit's incremental increase settings as against a coin insertion are shown in further details than in (B) above (refer to Table 3). Also, note that when this MANUAL SETTING is performed, (B) COIN CREDIT setting becomes ineffective.

MANUAL SETTING

COIN ASSIGNMENTS MANUAL SETTING

COIN TO CREDIT 1 BONUS ADDER NO BONUS ADDER COIN CHUTE #1 MULTIPLIER 1 COIN COUNT AS | COIN COIN 123456789 CREDIT 123456789

COIN CHUTE #2 MULTIPLIER 1 COIN COUNT AS 1 COIN COIN 123456789 CREDIT 123456789

SEQUENCE SETTING

->EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON (D) (E)

(G) COIN ASSIGNMENTS MANUAL SETTING

COIN TO CREDIT 1 BONUS ADDER NO BONUS ADDER COIN CHUTE MULTIPLIER 1 COIN COUNT AS | COIN COIN 123456789 CREDIT 123456789

SEQUENCE SETTING

->EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

Setting to COMMON

(D) COIN TO CREDIT Determines COIN/CREDIT setting.

(E) BONUS ADDER Setting to INDIVIDUAL

This sets how many coins should be inserted to obtain one SERVICE COIN.

(F) COIN CHUTE ( # 1 / #2 ) MULTIPLIER This sets how many tokens one coin represents.

Page 52

Table 1: COIN/CREDIT SETTING (COIN CHUTE COMMON TYPE)

NAME OF SETTING COIN CHUTE 1 COIN CHUTE 2

SETTING #1 1 COIN1 CREDIT1 COIN1 CREDIT
SETTING #2 1 COIN2 CREDITS1 COIN1 CREDIT
SETTING #3 1 COIN3 CREDITS1 COIN1 CREDIT
SETTING #4 1 COIN4 CREDITS1 COIN1 CREDIT
SETTING #5 1 COIN5_CREDITS1 COIN1 CREDIT
SETTING #6 1 COIN2 CREDITS1 COIN2_ CREDITS
SETTING #7 1 COIN5_CREDITS1 COIN2 CREDITS
SETTING #8 1 COIN3__CREDITS1 COIN3__ CREDITS
SETTING #9 1 COIN4 CREDITS1 COIN4 CREDITS
SETTING #10 1 COIN5_ CREDITS1 COIN5 CREDITS
SETTING #11 1 COIN6 CREDITS1 COIN6 CREDITS

SETTING #12 2 COINS 1 CREDIT 2 COINS 1 CREDIT

SETTING #13 1 COIN1 CREDIT2_ COINS 1 CREDIT
SETTING #14 1 COIN2_ CREDITS2_ COINS 1 CREDIT
SETTING #15 1 COIN1 CREDIT1 COIN1 CREDIT

2 COINS 3 CREDITS 2 COINS 3__ CREDITS

SETTING #16 1 COIN3 CREDITS1 COIN1 CREDIT

2_ COINS 3__ CREDITS

SETTING #17 3 COINS 1 CREDIT 3__ COINS 1 CREDIT

SETTING #18 4 COINS 1 CREDIT 4 COINS 1 CREDIT

SETTING #19 1 COIN1 CREDIT1 COIN1 CREDIT

2 COINS 2 CREDITS 2 COINS 2 CREDITS

3 COINS 3. CREDITS 3. COINS 3. CREDITS

4 COINS 5_ CREDITS 4 COINS 5 CREDITS

SETTING #20 1 COIN5 CREDITS1 COIN1 CREDIT

2 COINS 2 CREDITS

  • COINS 3. CREDITS

4 COINS 5 CREDITS

SETTING #21 5 COINS 1 CREDIT 5 COINS 1 CREDIT

SETTING #22 1 COIN2 CREDITS3. COINS 1 CREDIT

5 COINS 2 CREDITS

SETTING #23 2 COINS 1 CREDIT 2 COINS 1 CREDIT

4 COINS 2 CREDITS 4 COINS 2 CREDITS

5 COINS 3 CREDITS 5 COINS 3__ CREDITS

SETTING #24 1 COIN3 CREDITS2 COINS 1 CREDIT

4 COINS 2 CREDITS

5 COINS 3__ CREDITS

SETTING #25 1 COIN1 CREDIT1 COIN1 CREDIT

2 COINS 2 CREDITS 2 COINS 2 CREDITS

3 COINS 3 CREDITS 3. COINS 3. CREDITS

4 COINS 4 CREDITS 4 COINS 4 CREDITS

5 COINS 6 CREDITS 5 COINS 6 CREDITS

SETTING #26 1 COIN6 CREDITS1 COIN1 CREDIT

2 COINS 2 CREDITS

  • COINS 3 CREDITS

4 COINS 4 CREDITS

5 COINS 6 CREDITS

SETTING #27 FREE PLAY FREE PLAY

Page 53

Table 2: COIN/CREDIT SETTING (COIN CHUTE INDIVIDUAL TYPE) NAME OF SETTING] EACH SEAT'S COIN CHUTE | NAME OF SETTING] EACH SEAT'S COIN CHUTE

SETTING #1TCOIN_1 CREDITSETTING #21 | 5 COINS1 CREDIT
SETTING #21COIN2 CREDITSSETTING #23| 2COINS1 CREDIT
SETTING #31COIN3 CREDITS4 COINS2 CREDITS
SETTING #41COIN4 CREDITSSCOINS3 CREDITS
SETTING #51 COIN_5 CREDITSSETTING #25|COIN1 CREDIT
SETTING#I1_|1COIN6CREDITS2COINS2 CREDITS
SETTING #12__|2 COINS1 CREDIT3 COINS3 CREDITS
SETTING #15| 1COIN1 CREDIT4COINS4 CREDITS
2 COINS3 CREDITSSCOINS6 CREDITS
SETTING #17_|3 COINS1 CREDITSETTING #27_|FREE PLAY

SETTING #18 | 4COINS 1 CREDIT SETTING #19 | I1COIN 1 CREDIT 2COINS 2 CREDITS

3 COINS 3 CREDITS 4 COINS _5 CREDITS

Table 3: MANUAL SETTING

COIN TO CREDIT1COIN1CREDIT
2COINS1CREDIT
3.COINS1CREDIT
4COINS1CREDIT
5COINS1CREDIT
6COINS1CREDIT
7__COINS1CREDIT
8COINS1CREDIT
9COINS1CREDIT

BONUS ADDER NO BONUS ADDER COINS GIVE EXTRA COIN COINS GIVE EXTRA COIN COINS GIVE EXTRA COIN COINS GIVE EXTRA COIN COINS GIVE EXTRA COIN COINS GIVE EXTRA COIN COINS GIVE EXTRA COIN ©]}oo]ra}a}ufa}oo}ro COINS GIVE EXTRA COIN

COIN CHUTE (#1/#2) MULTIPLIER COIN COUNTS AS COIN COIN COUNTS AS COINS COIN COUNTS AS COINS COIN COUNTS AS COINS COIN COUNTS AS COINS COIN COUNTS AS COINS COIN COUNTS AS COINS COIN COUNTS AS COINS COIN COUNTS AS C]}olrafatufA}ofrml— COINS

Page 54

(G) SEQUENCE SETTING Number of credits required for starting game, etc. can be set. Function varies depending on the specific games. To find out what kind of functions are allotted to each sequence, or what is the initial value for each sequence, refer to the Instruction Manual of the game connected. Each sequence can be set between 1 ~ 5 credit(s).

COIN ASSIGNMENTS SEQUENCE SETTING

SEQUENCE 1 1 CREDIT(S) SEQUENCE 2 1 CREDIT(S) SEQUENCE 3 1 CREDIT(S) SEQUENCE 4 1 CREDIT(S) SEQUENCE 5 1 CREDIT(S) SEQUENCE 6 1 CREDIT(S) SEQUENCE 7 1 CREDIT(S) SEQUENCE 8 1 CREDIT(S) -> EXIT [WILD RIDERS XXXXXXXXXX] DESCRIPTION OF SEQUENCE 1 CREDIT TO START 2 NO USE 3 NO USE 4 NO USE 5 NO USE 6 NO USE 7 NO USE 8 NO USE

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

In cases of video games such as WILD RIDERS. : SEQUENCE | : Number of credits required for game start (initial value=1) SEQUENCE 2~8: NOT USED.

Page 55

G. BOOKKEEPING

+ BOOKKEEPING 1/2 This allows such data as operating time/No. of coins inserted/ No. of credits to be checked.

BOOKKEEPING 1/2

TOTAL TIME OD 00H 00M 00S

CREDIT °

COIN 1 COIN 2 COIN 3 COIN 4 oooo

TOTAL COIN 0 COIN CREDIT 0 SERVICE CREDIT 0 TOTAL CREDIT 0

PRESS TEST BUTTON TO CONTINUE

Press the TEST button to proceed to BOOKKEEPING 2/2.

  • BOOKKEEPING 2/2 Each sequence displays the frequency of functioning.

BOOKKEEPING 2/2

PISEQI 0 P1SEQ2 0 P1SEQ3 0 PLSEQ4 0 PLSEQS 0 P1SEQ6 0 P1SEQ7 0 PISEQ8 0

PRESS TEST BUTTON TO EXIT

In cases of video games such as WILD RIDERS. : PISEQ1: Play frequency of Player | PI SEQ2~8: NOT USED.

Page 56

H. BACKUP DATA CLEAR

Clears the contents of BOOKKEEPING.

BACKUP DATA CLEAR

YES(CLEAR) -> NO(CANCEL)

AND PRESS TEST BUTTON SELECT WITH SERVICE BUTTON

When clearing, bring the arrow to YES by using the SERVICE button and press the TEST button. Bring the arrow to NO and press the TEST button to have the menu mode return without clearing the data) COMPLETED is displayed when clearing is completed. Press the TEST button to return to the menu mode.

I. CLOCK SETTING

Set YEAR, MONTH, DAY, HOUR, and MINUTE for NAOMI 2 Main BD.

CLOCK SETTING

1998 12/02 14:30 33 WED

YEAR MONTH DAY HOUR MINUTE -> EXIT

AND PRESS TEST BUTTON SELECT WITH SERVICE BUTTON

Select the desired item with the SERVICE button and press the TEST button to increase the value. Upon finishing the SETTING, bring the arrow to EXIT and press the TEST button to return to the menu mode.

Page 57

J. ROM BOARD TEST

In this test, on-ROM-BD ROM check is executed. If GOOD is displayed below RESULT, it is satisfactory. BYTE and WORD refers to the check sum of each unit.

GAME ROM TEST [XXXXXXXXXXXXX]

NO. TYPE RESULT BYTE WORD 1C22 16M _ ---- 0123 4567 IC1 64M GOOD 0123 4567 IC2 64M GOOD 0123 4567 IC3 64M GOOD 0123 4567 IC4 64M GOOD 0123 4567 IC5 64M GOOD 0123 4567 IC6 64M GOOD 0123 4567 IC7 64M GOOD 0123 4567 IC8 64M GOOD 0123 4567 IC9 64M GOOD 0123 4567 IC1064M GOOD 0123 4567

1C20 64M GOOD 0123 4567

PRESS TEST BUTTON TO EXIT

Program ROMs (IC22) do not display GOOD or BAD. Press the TEST button to return to the menu mode.

K. GAME TEST MODE

Enters the TEST mode of the game connected. The TEST mode includes INPUT test, GAME ASSIGNMENTS such as game difficulty and others, BOOKKEEPING, etc. Depending on specific games, necessary items are added and unnecessary items removed. As such, the contents thereof may be changed.

Page 58

9-3 GAME TEST MODE

A. SETTING THE CARD

Be sure to use dedicated cards available for this product (i-e., 601-11051). Use of one other than such dedicated cards may cause a malfunction or failure of the machine. Be sure to set the specified number of cards in the specified orientation by using the specified procedure. Wrong setting of the cards may cause the machine to fail.

IMPORTANT!

This machine allows you to set upt ot 100 cards at a time. You must not set over 100 cards at a time. If you do so, a trouble such as card jamming may occur. Set virgin cards taken out from a container that was unpacked immediately before use. Use of any deformed or deteriorated card may cause trouble. Do not include a corrugated, bent, or used card in the card deck.

The card reader/writer is located on the top of the coin chute tower. Place the cards on the card reader/writer.

+ Unlock and open the cover to find the card reader/writer. The dispenser on which you should place the cards is located at the rear of the reader/writer.

+ From the car reader/writer, take out the dispenser upward in a straight line.

+ Remove the cover from the back of the dispenser.

+ Place the cards into the dispenser according to the instructions on the sticker annexed to the dispenser. There is no print face on a card of the Club Kart. Determine the card in reference to the inserting direction mark located at corners of the cards. Do not confuse the top/bottom or direction.

+ Reinstall the cover to the dispenser.

+ Insert the dispenser into the card reader/writer. The dispenser can be inserted only in the predetermined orientation.

+ Close and lock the cover.

Page 59

B. TURNING ON THE POWER

Turn on th AC unit’s main switch to supply power to the unit. Once power is turned on, the flourescent lamp in the bill board lights up. The Start System Screen displays after a lapse of several seconds. It is followed by the screen that indicates that the network is currently being checked if the communication mode has been set. If there is a bad or improper communication connection, each screen will not proceed to the next, remaining on the currently network-checked sreen. If this occurs, resolve the error according to the instructions in this document. If the communication mode has not been set or the communication check ends normally, the Motor Check Screen returns. While the Motor Check Screen is on-screen, the steering wheel can move either clockwise or counterclockwise. If you touch the wheel, the motor check is hindered and the game will not operate normally. So, you must not touch it at this time. Failures are displayed, if found. Resolve the errors according to the instructions in this document. Pressing the Start button while a failure is on-screen allows you to go to the next screen and start the game without reaction. Next the Check Card Reader/Writer Screen displays. If cleaning is required or a failure is found, this is indicated on the screen. In this case, resolve the error according to the instructions in this document. Once all the above steps have been completed, the Advertise Screen displays and voices are output through the left and right loudspeakers, unless you have set the machine so that no voices are output during the Advertise mode. This product retains the number of credits and the ranking data even after the power is turned off. It does not retain data about the fractional number of coins (i.e., the number of coins not reaching one credit) or the bonus adder count.

C. CARD READER/WRITER

Take care if you work with the machine, without turning the power, in an attempt to return to the game. In the alive state, the machine may operate suddenly, causing your finger to

CAUTION! be pinched or cut.

If a trouble such as card jamming occurs on the card reader/writer, you are notified of the trouble on the screen. You cannot proceed to a play unless you resolve the trouble at this time. First identify the trouble before you begin to take action. When all cards are used up, you can no longer issue a new card, with the message “Now new Club Kart Card” cannot be created” on-screen, instead of a trouble indication.

To obtain the dedicated or cleaning cards, place an order to the contact point or the dealer from which you purchased the product. In the order form, write down the card name and the amount of cards. With each of the following part numbers, you can purchase 200 dedicated and 30 cleaning cards. Dedicated Card Part number: 601-11051 Name: CARD PACKAGE CKT Cleaning Card Part number: 601-11050 Name: CLEANING KIT

Page 60
  • Action in Operation

The game board of this product backs up the data only when the card reader/writer detects a trouble DURING OPERATION and the Error Screen displays. However, no written data is backed up in the following cases:

+ An action deemed to be illegal was detected while the game or write was in operation.

If backed up data remains when the power is turned on, the Check Card Reader/Writer Screen will be replaced with the Save Data screen. The backed up data is cleared in the following cases:

+ After an action was taken against a trouble, normal write ended. + The backed up data was cleared in the Game Test Mode. + Data save taking place at power-on time was canceled, and the succeeding game ended.

If the card reader/writer has not been set as being unused, you will be unable to select any game mode with use of cards while the game will be in progress. Thus, for the card reader/writer, deal with the player, paying attention to the following points:

+ When a trouble occurs during write operation, the retained data can be written for proceeding to the game by resolving the trouble without turning on the power. If you resolved the trouble with power off, write the data according to the instructions on the screen when you attempt to turn on the power.

+ Even if the player request the system for use of cards when you have set the machine so that the card reader/writer is not used, the request is rejected because of the nature of the system.

  • Setting the Card
IMPORTANT! @ Be sure to use dedicated cards available for this product (i.e., 601-11051). Use of ones other than such dedicated cards may cause a malfunction or failure of the machine. @ Be sure to set the specified number of card in the specified orientation by using the specified procedure. Wrong setting of the cards may cause the machine to fail. @ This machine allows you to set up to 100 cards at a time. You must not set over 100 cards at a time. If you do so, a trouble such as card jamming may occur. @ Set virgin cards taken out from a container that was unpacked immediately before use. Use of any deformed or deteriorated card may cause a trouble.

The card reader/writer is located on the top of the coin chute tower. Place the cards on the card reader/writer. Card setting is enabled with power either on or off.

+ Unlock and open the cover to find the card reader/writer. The dispenser on which you should place the cards is located at the rear of the reader/writer. + From the card reader/writer, take out the dispenser upward in a straight line. + Remove the cover from the back of the dispenser. + Place the cards into the dispenser according to the instructions on the sticker annexed to the dispenser. There is no print face on a card of the Club Kart. Determine the card in reference to the inserting direction mark located at corners of the cards. Do not confuse the top/bottom or direction. + Reinstall the cover to the dispenser. + Insert the dispenser into the card reader/writer. The dispenser can be inserted only in the predetermined orientation. + Close and lock the cover.

Page 61
  • Head Cleaning
IMPORTANT! @ [f the head cleaning mode is entered while the power is on, use the head cleaning procedure according to the instructions on the screen. The head cleaning mode cannot be quitted for being ready for starting the game unless the head cleaning is completed. @ Be sure to use dedicated cleaning cards (i.e., 601-11050). Use of ones other than such dedicated cleaning cards may cause a malfunction or failure of the machine. @ Cleaning cards are disposable. They must not be used more than once. @ Use each cleaning card immediately after it is taken out from an unsealed package. Dried cards are ineffective for cleaning. @ Never use a cleaning procedure not described in this document. Use of it may cause a malfunction or failure of the machine.

This product memorizes the count you use the card reader/writer. When the power is turned off and on after the count of use exceeds 100, the head cleaning mode is entered while the Check Card Reader/Writer Screen is on-screen after you turn on the power. At this time, using a dedicated cleaning card, use the cleaning card procedure according to the instructions on the screen. The head cleaning mode cannot be quitted for being ready for starting the game unless the head cleaning is completed. You can use the Test Mode to perform the head cleaning mechanism assembly. For details, see the “Test Mode” section in this document.

Start the cleaning clears the count of use above.

+ Insert the cleaning card into the slot according to the instructions on the screen. The card is retracted automatically.

+ Ascreen displays that shows that cleaning is in progress.

+ Once the cleaning is completed, the cleaning card is ejected from the slot. Take out the cleaning card.

Cleaning Card Reader/Writer Screen

CARD R/W

CLEANING PLEASE INSERT CLEANING CARD

PRESS START TO CANCEL

Insert the cleaning card into the slot. Now cleaning. Wait for a minute. Cleaning is complete. Take out the card. You cannot proceed to the next step until you take it out.

Page 62
  • Takin Action Against Card Jamming

If card jamming occurs, the error is shown on the screen. Use the procedure to take action against the trouble:

+ Unlock and open the cover.

+ Unlock the hatch by drawing the green shaft attached to the top cover on the card reader/writer. While drawing the shaft, open the cover up.

+ Remove the card jammed in the card reader/writer.

+ While drawing the shaft, close the cover. With the top cover closed, release the green shaft. Check that the top cover has been locked securely.

Forcible Cleaning

This product memorizes the count you use the card reader/writer. When the power is turned off and on after the count of use exceeds 100, the head cleaning mode is entered while the Check Card Reader/Writer Screen is on-screen after you turn on the power. The head cleaning mode cannot be quitted for being ready for starting the game unless the head cleaning is completed. When the card reader/writer is subjected to head cleaning, the count of use is cleared and the the mode ends. At this time, using a dedicated cleaning card, use the cleaning card procedure according to the instructions on the screen. The count of use above is cleared also when the Test Mode is used for head cleaning.

Cleaning Card Reader/Writer Screen

CARD R/W

CLEANING PLEASE INSERT CLEANING CARD

+ Insert the cleaning card into the slot. The card is retracted automatically.

+ Now cleaning. Wait for a minute.

+ Cleaning is complete. Take out the card. You cannot proceed to the next step until you take it out.

Page 63

D. REWRITING DATA ONTO THE CARD

The game board of this product backs up the data only when the card reader/writer detects a trouble DURING OPERATION and the Error Screen displays. However, no written data is backed up in the following case:

+ An action deemed to be illegal was detected while the game or write was in operation.

If backed up data remains when the power is turned on the Check Card Reader/Writer Screen will be replaced with the Save Data screen. Once written onto the cord, the backed up data is cleared before the mode ends.

Write the data onto the desired card according to the instructions on the screen. You can use the Start button to cancel the write. The backed up data is cleared in the following cases: + Normal write ended. + The backed up data was cleared in the Game Test Mode. + Data save taking place at power-on time was canceled, and the succeeding game ended.

Rewrite Data Onto Card Screen

CARD R/W

DATA SAVE PLEASE INSERT CARD

PRESS START TO CANCEL

Insert the cleaning card into the slot. The card is retracted automatically.

+ Now writing data. Wait for a minute.

+ Data write is complete. Take out the card. You cannot proceed to the next step until you take it out.

Page 64

E. CARD LOW LEVEL ADJUSTMENT

+ Your game is equipped with a card “Low Level” system. It consists of a screw that moves with the magazine as cards are dispensed. When the screw gets low enough, the beam is interrupted and the LED is illuminated.

Added tape creates a flag to break beam sooner,

Low Level LED

+ Current configuration provides notification at approximately 10 card (+/- 2). If you feel you need sooner notification, see the diagram for suggested adjustment method.

Page 65

E. TROUBLESHOOTING

Card Reader/Writer Trouble

When a card reader/writer failure is detected while the game is in progress, the error type is shown on the screen. Take the appropriate error according to the actions listed below. The game board of this product backs up the data only when the card reader/writer detects a trouble DURING OPERATION and the Error Screen displays. However, no written data is backed up in the following case:

+ An action deemed to be illegal was detected while the game or write was in operation.

If backed up data remains when the power is turned on, the Check Card Reader/Writer Screen will be replaced with the Save Data screen. The backed up data is cleared in the following cases:

+ After an action was taken against a trouble, normal write ended. + The backed up data was cleared in the Game Test Mode. + Data save taking place at power-on time was canceled, and the succeeding game ended.

Error + Error condition + Action

“CONNECTION ERROR” Reader/ Writer Communication Error - Check the connection cables and then turn on the power again.

“MECHANIC ERROR1” DC Motor/Encoder Error - Check the connection cables and then turn on the power again. (Note 1)

“MECHANIC ERROR2” Thermal Head Elevation Error - Check the connection cables and then turn on the power again. (Note 1)

“CARD STUFFED” Card Jamming - Remove the card jam. (Note 2)

“MECHANIC ERROR3” Abnormal Temperature of Thermal Head - Check the connection cables and then turn on the power again. (Note 1)

“CARD EMPTY” Hopper Card Not Found - Supply card to the hopper. (Note 2)

“DRAW CARD ERROR” Error in Taking Out from the Hopper - Remove the card jame and check the hopper. (Note 2)

“CAN’T SAVE” No Data Can Be Written onto the Card. (Note 3)

“UNKNOWN ERROR” Error Other Than Above - Check the connection cables and then turn on the power again.

“SCIF ERROR” SCIF Error - Check the connection cables.

Page 66
Note 1: If this error reappears frequently, the card reader/writer body may be faulty.
Note 2: After the action has been taken, press the Start button before you follow the instructions on the error screen. Now you can return to the game.
Note 3: If the same error repeats again and again, clean the card reader/writer. If no data can still be written, the card reader/writer body may be faulty.

Without entering the Test Mode, turn on the power, again, to the cabinet if the following is included in the “Action” column in the above table: “turn on the power again.”

If the error is not included in the “Error” column in the above table, merely turn on the power again.

If no improvments result from the appropriate action listed in this document, contact one of the contact points listed in this document or the dealer from which you purchased the product.

Reaction Motor Trouble

When a failure is detected on the Check Motor Screen, which appears when the power is turned on. Use the following procedure to take action:

Error Display 1

STEERING DRIVE BD. IS NOT CONNECTED

PRESS START TO CANCEL OR PRESS VIEW TO RETRY

This is an error in communication between NAOMI 2 and the motor driver. Check the wiring. Pressing the Start button starts the game without steering-wheel reaction. Pressing the View button reinitiates the machine.

Error Display 2

STEERING DRIVE BD. DOES NOT WORK

PRESS START BUTTON TO CONTINUE WITHOUT REACTION FORCE

Page 67

This is an error that occurs when the motor could not be initialized properly. Check the wiring between the driver motors. Pressing the start button starts the game without steering-wheel reaction.

When a failure is detected while the game is in progress, it continues to operate until it ends.

After the game ends, you are brought to the same screen as Check Motor that appeared at power-on time. Ifa failure is detected at this time, Error Display 2, above, appears. Take action against it. Usually, the encoder annexed to the motor is used for detection of the steering wheel; however, it will be unavailable if a failure is detected on the motor. The handle mechanism is provided with a spare volume for this reason. When the handle center is set with Set Volume Control Screen in the Test Mode, volume center setting, as well as encoder setting, takes place. However, when you make the machine operate without reaction because of a motor failure, center the volume control again by way of precaution.

Page 68

F. GAME MENU

@ The new settings will not take effect until the Game Test Mode is exited. When you make change to the settings, exit the Game Test Mode by proper operation.

PORTANT! @ You must not attempt to demonstrate this game (for the selling purpose) with any other than those specified in this document. Use of such settings may cause malfunctions or bad operation on the machine.

SYSTEM MENU

GAME TEST MENU

M ASSIGNMENTS COIN ASSIGNMENTS BOOKKEEPING er BACKUP DATA CLEAR BOOK EERIE CLOCK SETTING “ id BACKUP DATA CLEAR ROM BOARD TEST aoa

GAME TEST MODE [XXXXXXXXXXXXXXX] SELECT WITH SERVICE BUTTON

> EXIT Gea PRESS TEST BUTTON

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

Pressing the SERVICE button moves the arrow on the screen. Move the arrow to select the item you want to run. Pressing the TEST button runs the currently selected item. The screen changes to the one for that item, and you can change or adjust the settings. Select EXIT and press the TEST button to return to the System Test Menu Screen.

Page 69

G. INPUT TEST

@ By selecting INPUT TEST on the Menu Screen and pressing the Test button, the steering wheel is centered automatically as done when the machine is started. To protect persons from accidents make sure that nobody is in contact with the steering

CAUTION! wheel before pressing the TEST button.

@ To prevent accidents, breakage of parts, and malfunctions, do not touch the steering wheel until centering of the steering wheel is completed.

INPUT TEST tests the input devices. Using this screen, check the input devices periodically. Operate each input device. If the display at the right of the appropriate device changes from OFF to ON, it is diagnosed as being normal. Check that each of the indications at the right of STEERING, ACCEL, and BRAKE change smoothly in response to operations of each of the input devices.

INPUT TEST

STEERING WHEEL: vate ACCEL. 7 eile BRAKE : +=e%

VIEW SW : OFF START SW H OFF

PRESS TEST AND SERVICE BUTTON TO EXIT

Pressing the TEST button returns you to the Game Test Menu Screen.

VOLUME CONTROL RECOMMENDED SETTINGS

+ Steering wheel: Centered (when traveling in a straight line) 2000H

+ Accelerator: When the pedal is released 30H When the pedal is pressed fully COH

+ Brake: When the pedal is released 30H When the pedal is pressed fully COH

Page 70

H. OUTPUT TEST

You can monitor the state of the lights. Use this screen to check the lights periodically.

OUTPUT TEST

START LAMP OFF VIEW LAMP OFF > EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

Pressing the SERVICE button moves the arrow. With the arrow aligned with the tested lamp item, press the TEST button. If the lamp lights up when the indication at the right of each name is ON and goes out when it is OFF, this lamp and wiring connections are normal. By selecting EXIT and pressing the TEST button, you return to the Game Test Menu Screen.

Page 71

I. GAME SETTING

You can make the settings about cabinet operations such as the communicated mode or the reaction force of the steering wheel.

MAKING CHANGE TO THE SETTINGS

By pressing the SERVICE button, move the arrow (>) to the desired item to change.

  • Pressing the Test button changes the display at the right of the currently selected item. Change the item to the desired display.
  • Press the SERVICE button to select EXIT. Then press the TEST button. This returns you to the Game Test Menu Screen.

> EXIT GAME SBET1

LINK TYPE: XXXXXX STEERING POWER: #23384: 4 sea

STEERING DIR. : REVERSE

CARD SYSTEM: ENABLE

BONUS GAMES: 0

SELECT WITH SERVICE BUTTON

PRESS TEST BUTTON TING

AND

@ LINK TYPE:

@ STEERING POWER:

@ STEERING DIR.:

@ CARD SYSTEM: @ BONUS GAMES: Used for settings of communicated play. You have four options: MASTER, SLAVE, SATELLITE, and STAND-ALONE. If you want to enjoy the game alone, set to STAND-ALONE. Setting for communicatedplay, be sure to set MASTER for only one machine, or seat, and set SLAVE for all the remaining ones. SATELLITE is a setting for a relay monitor. Sets reaction for the steering wheel. Increase or decrease in the number of asterisks (*) is reflected to the reaction force. The more the asterisks, the reaction force the larger. Sets steering reaction direction. Default for deluxe game is REVERSE. Activates card reader system.

Choose 0-3.

Page 72

J. VOLUME SETTING

CAUTION!

=

IMPORTANT! @ By setting VOLUME SETTING on the Menu Screen and pressing the TEST button, the steering wheel is centered automatically as done when the machine is started. To protect persons from accidents, make sure that nobody is in contact with the steering wheel, before pressing the TEST button.

@ Jo prevent accidents, breakage of parts, and malfunctions, do not touch the

steering wheel until centering of the steering wheel is completed.

@ No normal play is guaranteed unless all the input devices are set properly. Be sure to makethe proper settings before you begin demonstration for the selling purpose. @ Once you have completed change to the settings, select EXT and press the TEST button. The new settings will not take effect until this mode is exited.

By setting the VOLUME SETTING on the Menu Screen and pressing the Test button, centering of the steering wheel in initiated automatically. After the centering is completed, you can use the screen below to make the steering wheel, accelerator, and brake settings. If the operability of the steering wheel, accelerator, or brake is poor, use this screen to make the proper settings for the volume control.

VOLUME SETTING

MIN MID MAX [2000] 2000 STEER: *---------------------------------------------

[2000]3000 ACCEL: wn-encencnnenenecennnennnen

[8100]3000 C000 BRAKE: ----*-------------------------' er

> EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

  • By moving the SERVICE button to move the arrow, select the input device for which you want to make settings.
  • For either the accelerator or brake, press START without pressing the pedal. Set the value resulting when you release it.
  • With the pedal pressed fully, press START to set the value resulting when you press it fully. For the steering wheel, press START while supporting it along the straight line.
  • Select EXIT and press the TEST button. The setting changes are not updated until you select EXIT. After you make change to the settings, be sure to select EXIT. By selecting EXIT and pressing the TEST button, you return to the Game Test Menu Screen. ca
Page 73

K. CARD R/W TEST

Gror Check operation of the card reader/writer (R/W) and clean it periodically.

IMPORTANT!

This screen lets you check operation of the card reader/writer (R/W) or clean it.

CARD R/W TEST

CARD R/W STATUS: #88 INFORMATION

INITIALIZE CLEANING CHECK R/W: ---

> EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

The arrow can move to the following items: + INITIALIZE: _ Initialization

  • CLEANING: — Cleaning
  • CHECK R/W: _ R/W Operation Check

Depending on the R/W running mode, one of the following is displayed in “ *****” in “CARD R/W STATUS: ***#*” ;

READY Now waiting (Clear to Send Command) INITIAL Now initializing (Not Clear to Send Command) CLEAN Now cleaning (Not Clear to Send Command) GET Cards are being taken out from the hopper (Not Clear to Send Command) SAVE Sample data is saved onto the card (Not Clear to Send Command) LOAD Load card data and compares it with sample data (Not Clear to Send Command) OUT Eject cards (Not Clear to Send Command) ERROR Error ( Clear to Initialize Command Only)

While a status with a note of “Not Clear to Send Command” in parentheses is on-screen, no operations are accepted. If such a status has occured, wait until the operation in that status stops automatically and the display comes to READY. Should you need to cancel the operation forcibly, turn off the power. If you cancel it forcibly, be sure to select and run INITIALIZE after turning on the power.

Occasionally, the “INFORMATION” field on the screen outputs one of the instructions below, although it usually contains nothing.

Page 74

While cleaning is in progress, waiting in the ready mode for inserting a cleaning card:

----- PLEASE INSERT CLEANING CARD -----

After the operation check, waiting for the ready mode for ejecting the card:

----- PLEASE REMOVE CARD -----

When an error occurs, its type is displayed in the “INFORMATION” field:

CONNECTION ERROR Connection Error MECHANIC ERROR 1 DC Motor / Encoder Error MECHANIC ERROR 2 Thermal Head Elevation Error CARD STUFFED Card Jamming MECHANIC ERROR 3 AbnormalTemperature of Thermal Head CARD EMPTY Hopper Card Empty DRAW CARD ERROR Error in Taking Card from Hopper CAN’T SAVE Data cannot be written onto the card. UNKNOWN ERROR Unknown Error SCIF ERROR RC-232C Communication Error NO ERROR No Error

The “---” field in “CHECK R/W: ---” shows the result of the operation check.

_ Not Checked OK No Failure NG Failure

The operation check takes out each card from the hopper, and writes the sample data onto it. The check whether the read data matches the sample data. Then, the check ejects the card. When you draw out the card at this time, the entire process of the check is completed.

CHECKING R/W OPERATION

  • Select “CHECK R/W” and press the TEST button.

R/W operates automatically as follows:

Takes out the card from the hopper: GET is displayed. Saves the sample data onto the card: SAVE is displayed. Loads the data on the card for comparison with the sample data: LOAD is displayed. Ejects the card: OUT is displayed. Draws out the card. Now the entire process of the check is completed. AWRWN

If execution of the operation check results in display of NG, check the error condition. If you can take action against the error, execute the operation check again after you take the proper action. If you cannot take action against the error, repeat the check several times. If the result of the check is still NG, clean the R/W. If the subsequent execution of the operation check still results in NG, the R/W may be faulty.

If an error occurs, it is cleared by executing the INITIALIZE command. Note that when an error has occured, the R/W only accepts this command (except EXIT).

Page 75

CLEANING PROCEDURE

  • Select “CLEANING” and press the TEST button.

The following message appears to show that the R/W is ready for insertion of the cleaning card: ---PLEASE INSERT CLEANING CARD---

  • Insert the cleaning card into the R/W. On the screen, the status display is replaced with “CLEAN”, and cleaning begins.
  • Once cleaning ends after a lapse of a certain time, the R/W automatically ejects the card. The status display changes from “CLEAN” to “OUT.”
Page 76

L. BOOKKEEPING

In four pages, this screen lists the data about the operation status up to now. Pressing the TEST button brings you to the next page of the screen. When you press the TEST button on Page 4/4 of the screen, you return to the Game Test Menu.

BOOKKEEPING 1/4

NUMBER OF GAMES 0 NUMBER OF CARD GAMES, 0 NUMBER OF NEW CARDS v)

PLAY TIME OD OH AVERAGE PLAY TIME OH LONGEST PLAY TIME OH SHORTEST PLAY TIME OH

AND PRESS TEST BUTTON SELECT WITH SERVICE BUTTON OM OM OM OM Os Os Os Os

@ NUMBER OF GAMES: Number of games played.

@ NUMBER OF CARD GAMES: Number of games played with cards.

@ NUMBER OF NEW CARDS: Number of games played with cards.

@ PLAY TIME: Time played.

Page 77

BOOKKEEPING 2/4

TIME HISTOGRAM

OMO0S - OM29S OM30S - OMS59S 1MOOS - 1M29S 1M30S - 1M59S 2MOOS - 2M29S 2M30S - 2M59S 3MOOS - 3M29S 3M30S - 3M59S 4MOOS - 4M29S 4M30S - 4M59S OVER - SMOOS coooocoooocc[“

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

T IME HISTOGRAM lists the number of plays for each of the play times.

BOOKKEEPING 3/4

PLAYS/CLASS

RENTAL BEGINNER RENTAL NORMAL CLASS NOVICE CLASS B CLASS A CLASS S CLASS SS. CLASS SSS RRR RR RHE

SELECT WITH SERVICE BUTTON AND PRESS TEST BUT"

PLAY/CLASS shows the count of plays by class.

Page 78

BOOKKEEPING 4/4

PLAYS/COURSE

1-A * 1-B ~ 1-C * 2-A * 2-B * 2-C od 3-A * 3-B * 3-C * 4-A bd 4-B od 4-C *

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

The PLAYS/COURSE Screen lists the count of plays by course. Pressing the TEST button returns you to the Game Test Menu Screen.

Page 79

M. BACKUP DATA CLEAR

BACKUP DATA CLEAR deletes data on the Bookkeeping Screen. To delete data about the coins/credits, run BACKUP DATA CLEAR in the System Test Mode. Clearing the data does not influence any data settings (except the data).

BACKUP DATA CLEAR

YES (CLEAR) > NO (CANCEL)

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

To delete the data, use the SERVICE button to align the arrow with CLEAR and press the TEST button. Once the data is deleted, this screen displays “COMPLETED.” Pressing the TEST button again returns you to the Menu Screen. If you choose not to delete the data, press the TEST button with the arrow aligned with NO. This returns you to the Menu Screen.

Page 80

10. CONTROL PANEL (STEERING MOTOR UNIT)

WARNING! Before starting to work, ensure that the Power SW is OFF. Failure to observe this can cause electric shock or short circuit. Use care so as not to damage wirings. Damaged wiring can cause electric shock or short circuit. Do not touch undesignated places. Touching places not designated can cause electric shock or short circuit. This work should be performed by the Location's Maintenance Man or Serviceman. Performing work by non-technical personnel can cause electric shock hazard. Do not insert hand into the mechanism so as not to cause hand and fingers pinched in. Failure to observe this can cause a serious injury such as a fracture. When performing work such as parts replacement other than those specified in this manual, be sure to contact where you purchased the product from and confirm the work procedures and obtain precautions prior to performing work. Inappropriate parts replacement and/or installing with erroneous adjustment can cause an overload or the parts to come into contact, resulting in an electric shock, a short circuit, and a fire. Carefully handle the PTV on the PTV base because it is very unstable. If handled carelessly, it may fall down and eventually cause a serious personal injury.

10 - 1 ADJUSTING OR REPLACING THE V.R.

In cases the Steering operability is poor and the adjustment of VOLUME SETTING in the TEST mode is ineffective, the causes may be the Volume Gear's mesh failure and or Volume malfunctioning. By using the following procedure, adjust Volume gear mesh, or replace the Volume. In this product, when the Steering Wheel is moved fully left/right, if the Volume shaft is rotating within the movable range, the Volume is not feared to be damaged. Secure the Volume in the manner the Volume shaft is oriented as shown and the gears are appropriately engaged when the steering wheel is in the centering position allowing the car to go straight forward.

MECH FRONT LID

ADJUSTING THE VOLUME

® Turn off power.

® Turn off power @ Referring to Chapter 6, uncouple the’

Prepare a Phillips screwdriver and a wrench for M8 hexagonal nut.

PTV and the main cabinet from each other. However, leave the wires connected.

PHOTO 10. la

Page 81

@)The V.R. is on the VR BASE (a white, plastic made part). Loosen the 2 screws which secure the VR BASE and adjust the angle and appropriateness of gear mesh by moving the VR BASE. @®agiust to an appropriate mesh by securing the Steering Wheel in the direction allowing the car to advance straight forward and ensuring the "D" CUT FACE of the Volume shaft is oriented as shown.

© Tighten the 2 screws to secure the VR BASE.

1 | SCREW (2) ewe M4 X 12, w/flat & spring washers

"D" CUT FACE,

FIG. 10. 1a

© Turn on power.

@ Set the Center Value of the Volume in the TEST mode. @®in the TEST mode, check to see if the Volume Value varies smoothly in accordance with the steering wheel operation.

Page 82

REPLACING THE VOLUME

SCREW (2)

M4 X 12, wiflat & spring washers

® Disconnect the connector from the

Volume.

@ Take out 2 screws to remove the

Volume together with VR BASE from the HANDLE MECHA.

PHOTO 10. 1b

@Take out 2 screws from the VR

BASE reverse side to remove the Volume together with VR Bracket from the VR BASE.

@ Remove the Volume from VR

Bracket and replace.

TRUSS SCREW (2)

PHOTO 10. 1c

Page 83

® After replacing the Volume, engage the gears at the angular position shown and fix the VR Bracket.

t= SCREWO) M4 X 12, w/flat & spring washers

FIG. 10.1b

V.R, 220-5484 220-5373

© Turn on power.

Dset the Center Value of the Volume in the TEST mode. ®m the TEST mode, check to see if the Volume Value varies smoothly in accordance with the steering wheel operation.

10-2 GREASING

@ Be sure to use the designated grease. Using undesignated grease can cause parts damage. @ Do not apply greasing to undesignated places. Failure to observe this can cause malfunctioning or quality deterioration of parts.

. VOLUME GEAR MESH PORTION, Apply greasing to gear mesh portions once every 3 months. ape Use GREASE MATE (SEGA — _ PART NO. 090-0066).

PHOTO 10.2

Page 84
  • ACCELERATOR & BRAKE
WARNING! Before starting to work, ensure that the Power SW is OFF. Failure to observe this can cause electric shock or short circuit. Use care so as not to damage wirings. Damaged wiring can cause electric shock or short circuit. Do not touch undesignated places. Touching places not designated can cause electric shock or short circuit. This work should be performed by the Location's Maintenance Man or Serviceman. Performing work by non-technical personnel can cause electric shock hazard. When performing work such as parts replacement other than those specified in this manual, be sure to contact where you purchased the product from. Confirm the work procedures and obtain precautions from where you purchased the product from prior to performing work. Inappropriate parts replacement and/or installation with erroneous adjustment can cause an overload or the parts to come into contact, resulting in an electric shock, a short circuit, and a fire.

If Accel. and Brake operation is not satisfactory, adjustment of Volume installation position or Volume replacement is needed. Also, be sure to apply greasing to the gear mesh portion once every 3 months.

11-1 ADJUSTING AND REPLACING THE V.R.

® Secure the Potentiobase.

® Secure the Potentiobase (Q) Perform Volume setting in the

The appropriate value for both ACCEL. Volume and Brake Volume is under 30H when released and over COH when stepped on. Check Volume values in the TEST mode. Since work is performed inside the energized cabinet, be very careful so as not to touch undesignated places. Touching places not specified can cause electric shock or short circuit.

Take out the 2 truss screws and remove the Front Cover from the Accel. & Brake Unit

Loosen the screw which secure the Potentiobase, and adjust the Volume value by moving the Base. (FIG. 11. 1b)

Volume setting mode.

SCREW M5 X 12, w/flat & spring washers

POTENTIOBASE

V.R. 220-5484 220-5373 FIG. 11.1b

Page 85

REPLACING THE VOLUME

@Turn the power off. FIG. 11.1

@Turn the power off @ Take out the 2 screws and remove the ©

Pedal cover (FIG. 11. 1 c). di

® Disconnect the connector of the

Volume to be replaced.

Remove the screw which secures the Pedal base (FIG. 11. 1 b).

® Remove the Pedal base together with

the Volume as is attached. (FIG. 11. 1c)

Remove the Base and Gear to replace the Volume.

TRUSS SCREW (2) PEDAL COVER,

@Adiust the Volume as per the previous M4X8

page after replacing.

11 - 2 GREASING

IMPORTANT GREASING

Once every 3 months, apply greasing to the Spring and Gear mesh portion. For spray greasing, use GREASE MATE (PART No. 090-0066).

FIG. 11.2

Page 86
  • PROJECTOR

Ay Since the Projector has been adjusted at the time of shipment, avoid making

further adjustments without good reason.

CAUTION!

The Projector is subject to color deviation due to Convergence deviation caused by the geomagnetism at the installation location and peripheral magnetic field. After the installation of machine, and before commencing operation, check for

IMPORTANT Convergence deviation and if deviated, make adjustments.

Projector adjustments are stored. Due to distortion or color deviation in the TEST mode, if an adjustment is necessary, use the Remote Control to make adjustments. There are two Projector Makers (Toshiba and Mitsubishi) and the adjustment method varies depending on the specific maker.

12 - 1 CLEANING THE SCREEN

Since the Projector screen is susceptible to damage, pay careful attention to its handling. When cleaning, refrain from using water or volatile chemicals.

CAUTION!

When the screen surface ecomes dirty with dust, etc., clean it by using a soft cloth such as gauze. When water, and volatile chemicals such as enzine, thinner, etc., spill on the screen surface, it may be subject to damage, therefore, do not use them. Also, since the surfaces are susceptible to damage, refrain from rubbing them with a hard material or using a duster.

FIG. 12.1

Page 87

12-2 ADJUSTMENT OF TOSHIBA PROJECTOR

SETTING THE INTERFACE

IMPORTANT resulting in power off. In this product, set to INPUT LEVEL: 0.7V and IMPEDANCE: 75Q. Failure to observe this can cause CRT membrane to burn or Shutdown device to function

The Projector's Connector Panel contains the Interface setting SW.

O fe)

WINNER AC IN LAMP scioo-20 ANN GRIN IMPEDANCE INPUT LEVEL Oo =a 7

REMOTE CONTROL BUTTONS

When adjusting the Projector, direct the Remote Control's light emitting portion towards the Projector Screen.

MODE (mode selection) TEST (adjust/normal shift)

R. G. B. (color selection) <<

POSITION (to select the position) —

ADJUST (adjustment) REMOTE CONTROL LIGHT EMITTING PORTION

os we! 6.876 6 efo\e A; WRITING (storing the data) P (automatic color matching)

  • SET (to decide the selection)

PIC - ADJ (item selection) eeaev e/e\e a RESET ~ sonst — >) Ve e )| Ya seect (pattern selection) select)

NE”

Page 88

AUTOMATIC COLOR MATCHING

The Projector may be subject to color deviations affected by earth magnetism, the building steel frames, etc. When the Projector is initially installed or the Projector's installation position is changed, have the color matching performed automatically.

® Keep pressing the P button (red) for approximately 3 seconds to have

the ensuing movements performed automatically.

The Projector will shift to the color deviation

® correction mode from the game mode, with

the green cross pattern appearing on the screen.

=

| The cross pattern moves up/down and right/ ul > ©

PIc-ADJ Vv & yv

left to start the movement of searching the correct screen position and inclination.

When the green cross pattern movements are finished, similar detection is performed sequentially in order of red and then blue cross movements. After detecting by green, red and blue cross movements, the game mode returns with the color deviation status being corrected.

@ Although very rarely, the TRY AGAIN error display in red may appear. At this time, press the P button (red) for approximately 3 seconds. Even after the above operation is repeated, if the error condition still exists, then the display shifts to PLEASE ADJ. In this case, the auto color matching function can not be used. Contact the place of contact herein stated or where the product was purchased from.

@ !fthe automatic color matching indicates an error, color matching can manually be performed. Refer to CONVERGENCE ADJUSTMENT (manual color matching).

Page 89

ADJUSTING THE ON-SCREEN CONTRAST

Although the on-screen picture quality has been adjusted at the time of shipment from the factory, the on-screen contrast can be readjusted if desired. When the Game Board is replaced, readjustment may be necessary. Changing the CONTRAST causes the light and shade of the on-screen images to be changed. é A PIC-ADJ = @@e eee @| & © Ip 9 @-

ee iS) Le ® Press either AY or W PIC - ADJ button.

The on-screen menu will have one item in purple and 6 items in white. CONTRAST BRIGHTNESS, H.POSI V.POSI H.SIZE V.SIZE EXIT

@ Choose CONTRAST by using either 4 or W

PIC - ADJ button. 6604 ei) . e/e\e@ A Herein, (4 Aust — >) procedure @ @ @ LA is skipped. ICAL 8.

X ( @

aa

SET

: ADJUST j

WRITING

press the SET button. Have CONTRAST dis- CONTRAST ‘

BRIGHTNESS played in purple. Since

H.POSI CONTRAST is selected Nees initially, no particular V.siZE operation is required in this EXIT case.

® Press the SET button (to decide selection). When the selection of the CONTRAST adjustment mode is decided, the adjustment data scale bar appears on the screen. CONTRAST

@ Make adjustment by using either <q or > ADJUST button.

As the Cursor is moved, the adjustment data value changes. Make adjustment so as to obtain the desired on-screen contrast status.

® Press the WRITING button (for storing and finish).

The WRITING display appears and the adjustment data is stored.

WRITING

When discontinuing the adjustment, choose EXIT from the menu at the stage of procedure @ and

To continue adjusting other menu items, repeat procedure @ ~ Unless the adjustment data is stored, the data in the adjusted status will be erased at the time the power is turned off and the pre-adjustment status will remain when the power is turned on next time.

Page 90

ADJUSTING THE SCREEN BRIGHTNESS

Although the on-screen picture quality has been adjusted at the time of shipment from the factory, readjustment can be made if desired. When the Game Board is replaced, readjustment may be necessary. Changing the BRIGHTNESS causes the brightness of the on-screen images of black portions to be changed.

CONTRAST BRIGHTNESS H.POSI V.POSI H.SIZE V.SIZE EXIT

  • ADJ button.

PIC-ADJ

‘ ADJUST

WRITING CONTRAST BRIGHTNESS H.POSI V.POSI H.SIZE V.SIZE EXIT

, BRIGHTNESS 128 possetacharoscod tp

WRITING ® Press either 4. or W PIC - ADJ button.

The on-screen menu will have one item in purple and 6 items in white.

Choose BRIGHTNESS by using either 4 or W PIC

Have the BRIGHTNESS displayed in purple.

® Press the SET button (to decide selection).

When the selection of the BRIGHTNESS adjustment mode is decided, the adjustment data scale bar appears on the screen.

  • Make adjustment by using either <q or > ADJUST button. As the Cursor is moved, the adjustment data value changes. Make adjustment so as to obtain the desired on-screen brightness status.

® Press the WRITING button (for storing and finish).

The WRITING display appears and the adjustment data is stored.

@ When discontinuing the adjustment, choose EXIT from the menu at the stage of procedure @ and press the SET button. To continue adjusting other menu items, repeat procedure @-~ Unless the adjustment data is stored, the data in the adjusted status will be erased at the time the power is turned off and the pre-adjustment status will remain when the power is turned on next time.

Page 91

ADJUSTING THE ON-SCREEN DISPLAY POSITION

Although the on-screen display position (H. POSI, V. POSI) has been adjusted at the time of shipment from the factory, readjustment can be made if desired. When the Game Board is replaced, readjustments may be necessary.

PIC-ADJ

<— AbUUST

When making adjustments in vertical directions, also use either <4 or > ADJUST button.

WRITING. /\ ® Press either 4. or W PIC - ADJ button.

CONTRAST BRIGHTNESS H.POSI V.POSI H.SIZE V.SIZE EXIT The on-screen menu will have one item in purple and 6 items in white.

PIC ADJ button. Choose H. POSI or V. POSI by using either 4 or W

CONTRAST BRIGHTNESS H.POSI V.POSI H.SIZE V.SIZE EXIT Have the H. POSI or V. POSI displayed in purple. The Figure shows the status in which H. POSIT is selected.

@ Press the SET button (to decide selection). When the selection of the H. POSI or V. POSI is decided, the adjustment data scale bar appears on the screen.

(O) Make adjustment by usi: button. ing either <q or | ADJUST

WRITING As the Cursor is moved, the adjustment data value changes. Make adjustment so as to obtain the desired on-screen position status.

® Press the WRITING button (for storing and finish). The WRITING display appears and the adjustment data is stored.

@ When discontinuing the adjustment, choose EXIT from the menu at the stage of procedure(2) and press the SET button. To continue adjusting other menu items, repeat procedure Unless the adjustment data is stored, the data in the adjusted status will be erased at the time the power is turned off and the pre-adjustment status will remain when the power is turned on next time.

Page 92

ADJUSTING THE SCREEN SIZE

Although the on-screen size (H. SIZE, V. SIZE) has been adjusted at the time of shipment from the factory, readjustment can be made if desired. When the Game Board is replaced, readjustments may be necessary.

> @ S = / <

¢ ee ®@

© Ole @ J @ @ @ = @(@)@ @ @|

onl (@:) oo <> 4 z PIC-ADJ Le:

« ADJUST

When making adjustments in vertical directions, also use either < or > button.

WRITING

the SET button. ® Press either 4. or W PIC - ADJ button.

CONTRAST BRIGHTNESS H.POSI V.POSI H.SIZE V.SIZE EXIT

PIC - ADJ button.

CONTRAST BRIGHTNESS H.POSI V.POSI H.SIZE V.SIZE EXIT

® Press the SET button

button.

WRITING The on-screen menu will have one item in purple and 6 items in white.

Choose H. SIZE or V. SIZE by using either 4 or W

Have the H. SIZE or V. SIZE displayed in purple. The Figure shows the status in which H. SIZE is selected.

(to decide selection).

When the selection of the H. SIZE or V. SIZE adjustment mode is decided, the adjustment data scale bar appears on the screen.

@ Make adjustment by using either < or > ADJUST

As the Cursor is moved, the adjustment data value changes. Make adjustment so as to obtain the desired on-screen position status.

© Press the WRITING button (for storing and finish). The WRITING display appears and the adjustment data is stored.

To continue adjusting other menu items, repeat procedure @ ~@. Unless the adjustment data is stored, the data in the adjusted status will be erased at the time the power When discontinuing the adjustment, choose EXIT from the menu at the stage of procedure 2) and press

is turned off and the pre-adjustment status will remain when the power is turned on next time.

Page 93

CONVERGENCE ADJUSTMENT (manual color matching)

CONVERGENCE ADJUSTMENT (Line Convergence Adjustment in particular) A To avoid circuitry malfunctioning due to electrical load increase, never utilize for adjusting screen size changes.

CAUTION! There is no means to restore the Convergence Adjustment data once stored, to its original state. To avoid changing the screen size by erroneously using convergence adjustment, do not perform the green Line Convergence Adjustment. As such, be sure to perform the adjustment work from this page onward by the Technical staff and the location's Maintenance Personnel who are well versed in such adjustment work. In the Static Convergence Adjustments, if satisfactory adjustments can not be performed, do not make another convergence adjustments inadvertently. Contact the office herein stated or where the product was purchased from.

To avoid making the adjustment work ineffective, do not press the RESET button during adjustment.

IMPORTANT To discontinue adjustment work, keep pressing the TEST button for

" approximately 3 seconds at the stage before storing the adjustment data by pressing the WRITING button.

Should the screen be abnormally disturbed by noise due to static electricity, etc., turn the power off without storing the adjustment data. Pressing the or PIC - ADJ button in the Convergence Adjustment mode status will display the Adjustment Menu shown right. Do not utilize this Adjustment Menu as this is the one applied at the factory. SUB V$IZE SUB H$IZE ADJUST MODE

Adjusting this menu causes the Customer's adjustment range to be deviated.

Should the menu shown right be Adjustment menu used in the factory. displayed by mistake, first choose EXIT by using either or PIC - ADJ button and then press the SET button.

Page 94

STATIC CONVERGENCE ADJUSTMENT

In the static convergence adjustment, each of red and blue images is comprehensively moved to and superimposed on the green color. If automatic color matching function is not sufficiently satisfactory, perform this adjustment. Be sure to perform automatic color matching before starting the above adjustment.

5 MODE 7 oa gies es 6 MR @ © @

@v ¥

(a Abust ‘| >) e @ ‘SELECT 7 &.@ ee

When either of COLOR SELECT buttons (R, B) is pressed, if the color desired to be adjusted disappears, press that particular button again. For example, if the red color needs to be adjusted again at the stage of , the R button need to be pressed twice. Keep pressing the TEST button for approximately 3 seconds. The screen will change to ADJUST mode from the Game mode to cause the green test = ADIUSF MODE—

“A DO NOT PUSH THIS. eces pattern to be displayed on the screen.

Press the R button to have the red adjustment mode. The red test pattern is added to the display. The frame color [—ADIUS}] MODE—

turns red and this signifies the red adjustment mode.

Make adjustment by using the & W < > ADJUST buttons.

Make adjustment so as to have red superimposed on green. When red is superimposed on [—ADIUSF MODE—

green, the color becomes yellow.

Press the B button to have the blue adjustment mode.

Similarly as in the case of red, adjust the blue color. When green, red, and blue are super- —ADIUyF MODE—

LF DIUSP MODE— Lo ng imposed, the color becomes white.

Press the WRITING button (for storing and finish). The WRITING display appears and the adjustment data is stored. After the data is stored, the Game mode returns.

Page 95

POINT CONVERGENCE ADJUSTMENT

In the POINT CONVERGENCE adjustment, each of red, green and blue images is partially moved for color matching. The adjustment may be necessary when the Game Board is replaced or changed, or screen size is changed. Be sure to perform automatic color matching before starting the adjustment.

MARKER | Keep pressing the TEST button for approximately 3 seconds. [epee] | The screen changes to ADJUST mode from the Game mode and displays the green test pattern.

Press the MODE button twice to have the POINT ADJUSTMENT mode. Note 1

The crosshatch test pattern appears and the MARKER indicating the

DO NOT PRESS.

iS)

Note 1 When the MODE button is repeatedly pressed, the adjustment modes will circulate as follows:

STATIC ADJUSTMENT MODE

LINE ADJUSTMENT MODE

POINT ADJUSTMENT MODE:

Note 2 When either of the COLOR SELECT buttons (R, B) is pressed, if the desired color to be adjusted disappears, press that particular button again.
Note 3. By repeatedly pressing the SELECT button, only the Projector's TEST pattern screen and the screen superimposing the Game Board Test pattern can be alternately displayed. adjustment point is displayed.

@ Using either R or B button, select the desired color to be adjusted. Note 2 By using the G button, the green color can also be selected.

The selected color is displayed by superimposing on green. The MARKER will be in the color selected.

@ By using the & W move the MARKER to the position to be adjusted. <q > ADIUST buttons,

The MARKER moves in the direction of the button's arrow. However, the movable point is predetermined.

G) Make adjustment by using the & W < > ADJUST butto ns. Although the direct vicinity of the MARKER's center moves most conspicuously, make adjustment by paying attention to the periphery area also. Shown left is the magnified MARKER periphery.

© Press the SELECT button as necessary to

superimpose G: ame Board images. Note 3 If the test pattern is not displayed in the periphery of the screen, adjustments can be made by pressing the SELECT button to superimpose the test pattern and the Game Board's CRT test screen.

ING button (for storing and finish).

WRITING is displayed and the adjustment data is stored. After the data is stored, the Game Board screen returns.

Page 96

LINE CONVERGENCE ADJUSTMENT

Iss In the LINE CONVERGENCE ADJUSTMENT, the adjustment point of the column line (vertical) or row line (horizontal) is comprehensively moved for color matching. It is convenient to utilize this adjustment when the color of the column line or row line is uniformly deviated.

DO NOT PUSH. @/ole &, 2 @eeyv

l y

Note | When the MODE button is repeatedly pressed, the adjustment modes will circulate as follows:
Note 2 Ss ATIC ADJUSTMENT MODE

LINE ADJUSTMENT MODE

P MARKER.

® Keep pressing the TEST button for approximately

3 seconds.

[—ADIUSF MODE— The screen changes to ADJUST mode from the Game Board mode and displays the green test pattern.

@) Press the MODE button once to have the POINT

ADJUSTMENT mode. Note 1

HE: The crosshatch test pattern appears ra and the vertically long MARKER is shown.

® Using either R or B button, select the desired color to

be adjusted. Note 2 Although the green color can also be selected by using the G button, to avoid the screen size change adjustment, do not choose green. The selected color is displayed by superimposing on green. The MARKER will be in the color selected.

@By using the & W <q > POSITION buttons, move the MARKER to the position to be adjusted.

Use the <q p> buttons to select the column line, and the MARKER OINT ADJUSTMENT MODE

When either of the COLOR SELECT bi uttons (R, B) is pressed, if the desired color to be adjusted disappears, press that particular button again. moves in the right/left direction. However, the movable range is predetermined.

Use the & W buttons to select |S=======——= 4 the row line and the MARKER moves in the up/down direction. However, the movable range is predetermined.

® Make adjustment by using the & W <4 > ADJUST buttons. The selected column line or row line (shown left is the column line) can be moved in the desired up/ down or right/left directions as applicable.

© Press the WRITING button (for storing and finish). WRITING is displayed and the adjustment data is stored. After the data is stored, the Game Board screen returns.

Page 97

12 -3 ADJUSTMENT OF MITSUBISHI PROJECTOR

A (UP shift),<] (LEFT shift), W (DOWN shift), [> (RIGHT shift), TEST, -, +, and PICTURE. Do not press keys other than those explained in

IMPORTANT this manual. S @ For the operation of Remote Control, use only the Keys of R/B,

@ When operating the Remote Control, have it point the screen.

The Projector has DYNAMIC CONVERGENCE adjustment functions. This manual does not refer to the functions as the adjustment of DYNAMIC CONVERGENCE is very troublesome and in addition, visual effects are negligible.

UP shift)KEY

R/B KEY

RIGHT shift)KEY ‘LEFT shift)KEY

DOWN shift)KEY

TEST KEY

~ KEY

PICTURE KEY

Page 98

+ POWER KEY ....................., This does not have power ON/OFF function. Does not function even if it is pressed.

  • RIBKEY oes Used to select "R" for red adjustment or "B" for blue adjustment in the STATIC CONVERGENCE ADJUSTMENT mode.
  • AUP shift) KEY................. Used to move the test cross upward in the STATIC CONVERGENCE ADJUSTMENT mode.
  • <|(LEFT shift) KEY ........... Used to move the test cross to the left in the STATIC CONVERGENCE ADJUSTMENT mode.

+ W (DOWN shift)................... Used to move the test cross downward in the STATIC CONVERGENCE ADJUSTMENT mode.

+ [> (RIGHT shift) KEY.......... Used to move the test cross to the right in the STATIC CONVERGENCE ADJUSTMENT mode.

  • TEST KEY 0.0. cece This is the ON/OFF key in the STATIC CONVERGENCE ADJUSTMENT mode. In the ON status of this key, the test cross pattern appears in the approximately on-screen center. + ENTER KEY ..............0.04.-..-.. Used for DYNAMIC CONVERGENCE.

© KEY oer Used to decrease the adjustment data in the adjustment mode of CON- TRAST, BRIGHTNESS, HORIZONTAL/VERTICAL POSITIONS and WIDTH.

... Used to increase the adjustment data in the adjustment mode of CON- TRAST, BRIGHTNESS, HORIZONTAL/VERTICAL POSITIONS and WIDTH.

  • PICTURE KEY 0... Used for the ADJUSTMENT mode of CONTRAST, BRIGHTNESS, HORI- ZONTAL/VERTICAL POSITIONS and WIDTH. Every time this key is pressed, the ADJUSTMENT mode proceeds as follows:

NORMAL CONTRAST BRIGHTNESS H-POSI > OPERATION [—t| ADJUSTMENT }|—?> ADJUSTMENT }—?> ADJUSTMENT MODE MODE MODE

V-HEIGHT V-POSI H-WIDTH ADJUSTMENT \«@— ADJUSTMENT jt ADJUSTMENT xt? MODE MODE MODE

[EXPLANATIONS OF ADJUSTMENT MODES

  • CONTRAST Used to vary image contrast. Use + and - keys to adjust. + BRIGHTNESS Used to change image brightness. Use + and - keys to adjust. + H-POSI ........................ Used to move the image position in the horizontal direction. Use + and - keys to adjust. + H-WIDTH ................... Used to change the horizontal width of image. Use + and - keys to adjust. © V-POSI oct Used to move the image position in the vertical direction. Use + and - keys to adjust. + V-HEIGHT ......0.0 Used to change the vertical width of image. Use + and - keys to adjust.
Page 99

STATIC CONVERGENCE ADJUSTMENT

Press the TEST KEY to change the screen to Red Line Adjustment mode.

Superimpose the red line on the green line. When the red line is superimposed on the green line, the green line turns to yellow or white.

To MOVE RED LINE: Use <j] key to move it left. Use [> key to move it right. Use @& key to move it upward. Use key to move it downward.

Press the R/B KEY. Changes to the Blue Line Adjustment screen. Every time the key is pressed, "from red to blue" and "from blue to red" are alternated.

SUPERIMPOSING BLUE LINE ON GREEN LINE: Superimposing blue line on green line causes the green line to turn to white.

TO MOVE BLUE LINE: Use <]_ key to move it left. Use [> key to move it right. Use A key to move it upward. Use 'W key to move it downward.

Press the TEST KEY. Adjustment is finished. RED 31K

H¥75 Vi-11

R <J ————-* A

V

B < ———-* A

V

AUTOMATIC CANCELLATION OF ADJUSTMENT MODE

In each adjustment mode, only in the case where an effective key input (variation of values and images) is not performed within the time limit indicated below, the adjustment mode is automatically cancelled and finished, shifting to on-screen normal images.

Approximately 6 seconds

Approximately 5 min. CONTRAST BRIGHTNESS H-POSI H-WIDTH V-POSI V-HEIGHT

STATIC CONVERGENCE

Page 100
  • COIN SELECTOR

HANDLING THE COIN JAM

If the coin is not rejected when the REJECT button is pressed, open the coin chute door and open the selector gate. After removing the jammed coin, put a normal coin in and check to see that the selector correctly functions.

CLEANING THE COIN SELECTOR

@ Remove and clean smears by using a soft cloth dipped in water or diluted chemical detergent and then squeezed dry. Never apply machine oil, etc. to the Coin Selector. After cleaning the Coin Selector, insert a regular coin in the normal working status and ensure that the Selector correctly functions.

The coin selector should be cleaned once every 3 months. When cleaning, follow the procedure below:

® Turn the power for the machine OFF. Open the @ Open the gate and dust off by using a soft brush

coin chute door.

(made of wool, etc.). Remove and clean smears by using a soft cloth dipped in water or diluted chemical detergent and then squeezed dry. Remove the CRADLE. When removing the retaining ring (E ring), be very careful so as not to bend the rotary shaft.

® Remove stain from the rotary shaft and shaft

receiving portions by wiping off with a soft cloth, etc.

After wiping off as per ® above, further apply

a dry cloth, etc. to cause the coin selector to dry completely.

COIN INSERTION TEST

Once every month, when performing the Coin SW Test, simultaneously check the following: [Does the Coin Meter count satisfactorily? |” [Does the coin drop into the Cashbox correctly? Is the coin rejected when inserted while keeping the Reject Button pressed down? Insert a coin while keeping the Reject Button pressed down and check if it is rejected.

COIN

FIG. 13 ¢

Page 101

[= 4 S S ow

  • ow => Sass SASBEB
  • Sree YSEPS ees G awn a SSEEG S2zita Ssnuan SN_as o >

= oO fs} ro fre S = = z axa wes Bee moO= tes ess AS 1” —1OQus luz>=<es =Soss FES Bes ase

Page 102

Tom Happ Ph: 847-593-6161 ext. 107 tom.happ@happcontrols.com Fx: 847-956-2091 Happ Controls, 106 Garlisch Drive, Elk Grove, IL 60007 Visit our website http://www.happcontrols.com 42-0641-00 \> 1131900 #2-0288-00 (7

4a 42-0351-00 adele 43-1002-00 \

43-1003-00 42-7355-00 _ (s) 42-0065-00. 48-1000-00 Nes

= $0.25 42-3079-00 $1.00 42-3113-00 48-7067-00: ; 42.0641-00 43-0196-00—ew 42-0206-00 42-0082-00

n 42-8177-00 42-8176-00 = 42-0405-00 FOR §.25 COIN 42-0405-05 FOR $1.00 COIN 5 o.. 0231-00 42-1044-00 $1.00 4 x .25 1 PLAY 42-0695-05 $1.00 PUSH TO REJECT

42-7201-00

  • 42-0232-00 42-0119-00 @a— 41-0021-00 42-8178-00
  • 42-8174-10 Guardian Hasp 30-2400-200
Page 103

OPTIONAL DOLLAR BILL ACCEPTOR

@ THE COIN DOOR ASSEMBLY USED ON CLUB KART DX COMES EQUIPPED TO ACCEPT A DOLLAR BILL ACCEPTOR. ALL NEEDED WIRING CONNECTIONS ARE CONVIENENTLY LOCATED INSIDE THE GAME FOR THIS APPLICATION.

@ THE COIN DOOR CAN ACCCOMMODATE THE FOLLOWING VALIDATOR(S):

FORWARD-MOST Mars 2000 series HOLE POSITION

**42-1155-00 MARS VALIDATOR $1, 2,5 300 CAP

The frame and cashbox enclosure on this coindoor has been modified to accomodate a Mars 2000 series upstacker. A 2000 series stacker can be added by simply removing the cut-out plate. This one entry door can be ordered through Happ Controls or one of Happ Controls authorized distributors. The part number is 40-6000-10EX. The Mars stacker can be obtained through an autherized Mars distibutor.

Note: Your game may have either Happ Controls Coin Door Assembly or the Wells Gardner Coin Door Assembly (not shown).

**Happ part number

Security Locking Bar/Bracket Set Part No.# 999-0966

Modified Cash Box (For use when DBA installed) Part No. # 999-1106

Plastic Cash Box - Full Size Part No. # 999-1177

Page 104

**Coin door shown with optional dollar bill validator inserted**

Page 105

14. REPLACING THE FLUORESCENT LAMP, AND LAMPS

can cause electric shock and short circuit hazards.

WARNING! The Fluorescent Lamp, when it gets hot, can cause burn. Be very careful

when replacing the Fluorescent Lamp. Be sure to use lamps of the designated rating. Using lamps of undesignated rating can cause a fire or malfunctioning.

Ay When performing work, be sure to turn power off. Working with power on

To perform work safely and securely, be sure to prepare a step which is in a secure and stable condition. Performing work without using the step can

CAUTION! cause violent falling down accidents. Be careful when handling the plastic made parts. Failure to observe this may cause injury due to damage or fragments resulting from damage.

INSIDE THE BILLBOARD

Remove the billboard holder, slide up the billboard plate, and replace the fluorescent tube.

‘T+__TRUSS SCREW (3) black M4X8 BILLBOARD HOLDER

t _ BILLBOARD PLATE ee ee

FLUORESCENT LAMP 32W:390-5251-32-01 GLOW LAMP:390-5638-5P_

FIG. 14a

Page 106

START BUTTON, VIEW CHANGE BUTTON

® Turn power off.

@ Remove the 4 Trusshead screws.

SWITCH PLATE

TRUSS SCREW (4)

M4 X 8, chrome

PHOTO 14a

Remove the switch plate from the control panel carefully without damaging the wires.

@on the rear side of the switch plate there is a metallic projection

on the foot of each button. Turn the projection to unlock, and remove the wire connection part from the button body.

The lamp is inside the wiring connecting portion. Push and then turn the Lamp counterclockwise to remove.

Page 107
  • PERIODIC INSPECTION TABLE

The items listed below require periodic check and maintenance to retain the performance of this machine and to ensure safe business operation. When handling the controller, the player will be in direct contact with it . In order to always allow the player to enjoy the game, be sure to clean it regularly. Also, it is advisable to provide wet tissue, etc. available for player use.

@ Be sure to check once a year to see if Power Cords are damaged, the plug is securely inserted, dust is accumulated between the Socket Outlet and the

WARNING! Power Plug, etc. Using the product with dust as is accumulated can cause fire and electric shock hazards. Periodically once a year, request the place of contact herein stated or the Distributor, etc. where the product was purchased from, as regards the internal cleaning. Using the product with dust as is accumulated in the interior without cleaning can cause a fire or accident. Note that cleaning the interior parts can be performed on a pay-basis.

TABLE 15

ItemIntervalReference
CABINETCheck Adjusters'contact with surface.Daily3

CONTOROL PANEL Cleaning As necessary

Inspection of SW, VR.Monthly9
Greasing to the gear mesh portion.Trimonthly10-2
ACCEL. & BRAKECheck VOLUME VALUE.Monthly9
Gear and Spring portion greasingTrimonthly11-2
COIN CHUTE DOORCheck COIN SW.Monthly9
Coin insertion test.Monthly13
Cleaning of COIN SELECTOR.Trimonthly13
PROJECTORSCREEN cleaning.Weekly12-1
Check adjustments.‘Monthly or when moving.6,9, 11
SEATGreasing to the seat railTrimonthlyFIG.1S
GAME BDMEMORY TEST.Monthly9
Check settings.Monthly9
INTERIORCleaningAnnuallySee above.

POWER SUPPLY PLUG Inspection and cleaning

Cabinet surfacesCleaningAs necessary.See below.

CLEANING THE CABINET SURFACES

When the cabinet surfaces are badly soiled, remove stains with a soft cloth dipped in water or diluted (with water) chemical detergent and squeezed dry. To avoid damaging surface finish, do not use such solvents as thinner, benzine, etc. other than ethyl alcohol, or abrasives, bleaching agent and chemical dustcloth.

Page 108

SEAT (Greasing to Seat Rail Portion)

Move the Seat to the rearmost portion and apply spray greasing to the portion shown at the right once every 3 months by using NOK KLUBER L60 or GREASE MATE SEGA PART No. 090-0066. After greasing, move the Seat a few times forward and backward so as to allow the grease to be applied all over uniformly. Be sure to wipe grease which attaches to the surfaces of the PROTECT RUBBER on the Seat Rail, or any excess grease. FIG. 15

Page 109
  • TROUBLESHOOTING
WARNING! @ [norder to prevent electric shock and short circuit, be sure to turn power off before performing work. @ Be careful so as not to damage wirings. Damaged wiring can cause electric shock or short circuit. @ After removing the cause of the functioning of the Circuit Protector, reinstate the Circuit Protector. Depending on the cause of the functioning, using the Circuit Protector as is without removing the cause can cause generation of heat and fire hazard.

In case a problem occurs, first check wiring connector connections. TABLE l6a

PROBLEMS CAUSE COUNTERMEASURES

With Main SW ON, no activation. Power is not supplied.

Power supply/voltage is not correct.

The Circuit Protector functioned due to the momentary overload. Securely insert the power plug into the plug socket.

Make sure that power supply/voltage is correct.

After eliminating the cause of overload, reinstate the AC Unit's Circuit Protector (see [4], Sec. 6, Refer to the following). Reset the circuit protector on the ASSY ELEC. (see PHOTO 16 a, b)

The color on PTV screen is incorrect. Image adjustment is inappropriate. Adjust appropriately (see Sec.12).

Color deviation on PTV screen. Affected by peripheral machines or the building's steel frames. Perform convergence adjustment (see Sec. 12).

Change installation direction or position.

Move the machine which causes the problem.

No sound is emitted. Sound volume adjustment is not appropriate.

Board and Amplifier malfunctioning. Adjust sound volume (see Sec. 9).

Perform the sound test and confirm (see Sec. 9).

Page 110

TABLE 16b

PROBLEMS CAUSE COUNTERMEASURES

Operability of the Steering wheel (handle) is poor. Deviation of the volume value.

Volume gear engagement fault.

Volume malfunctioning. Adjust the volume value in the Test mode. (see 9-3)

Adjust the engagement of the gear. (see 10-2)

Replace the Volume. (see 10-2)

Steering wheel (handle) is abnormal in its force feedback. It is not centered. Failure of power-on checking procedure.

The volume is not centered.

Failure of the volume. Reconnect the power, and complete a power-on checking procedure. (see 5 Sec. 6,)

Adjust the volume value in the test mode. (see Sec. 9)

Replace the volume. (see 10-1)

Steering wheel (handle) is week in its force Aging of the force feedback mechanism. Reset in the test mode. (see Sec. 9)

operate normally. Failure of the volume. feedback.

Gas pedal The volume is not centered. Adjust the volume value in the test mode. (accelletor) and/or (see Sec. 9) brake pedal do not Replace the volume. (see 11-1)

The Fluorescent lamp does not light up. The Fluorescent tube is burnt out. Replace the Fluorescent tube (see Sec. 14).

Lights integrated with the start button and the view change button do not come on. The lamp is burnt out. Replace the lamp. (see Sec.14)

Failure of the Communication cables are Reconnect the cables. (see 19-2) communication disconnected. play. Communication cables are wrongly Reconnect the cables correctly. (See 19-2) connected.

Communication play is wrongly set. Reset correctly. (see 19-3)

"ERROR *' is Setting error in the test mode. Reset correctly in the test mode according displayed. to the product. (see Sec. 9)

Page 111

FUSES on the ASSY ELEC

nN Carefully handle the PTV on the PTV base because it is very unstable. If handled carelessly, it may fall down and eventually cause a serious personal injury.

WARNING!

A circuit protector is located both in the AC unit and on the main cabinet's ASSY ELEC. If the connection of the power fails even though you have turned the main switch on, either circuit protector may have tripped. If the main switch does not function normally, check the circuit protector on the ASSY ELEC.

FRONT LID

Referring to Chapter 6, uncouple the main cabinet from the PTV. However, leave the wires connected.

Remove the 2 trusshead screws to detach the front lid from the main cabinet

Now, you can access to the circuit protector on the ASSY ELEC.

PHOTO 16b

ASSY ELEC

Page 112
  • GAME BOARD

A

WARNING!

A

CAUTION!
IMPORTANT @ ‘norder to prevent electric shock and short circuit hazards, be sure to turn power off before performing work. @ Be careful so as not to damage wirings. Damaged wiring can cause fire, electric shock and short circuit hazards. @ Do not expose the Game BD, etc. without a good reason. Failure to observe this can cause electric shock hazard or malfunctioning.

The electronic parts on the IC Board could be damaged due to human body's static electricity. Before performing IC Board related work, be sure to discharge physically accumulated statics by touching grounded metallic surfaces, etc.

Put the Game Board in the Carton Box (an accessory) together with the Shield Case when requesting for the replacement or repair. Transporting the Game Board in an undesignated status for replacement/repair is unacceptable. In this manual, how to remove the Game Board is explained for convenience. However, this work should be performed by SEGA SERVICEMAN.

Page 113

17 - 1 REMOVING THE GAME BOARD

@Tum power off. @ Remove the 2 trusshead screws of the back lid, unlock it, and detach it from the main cabinet.

® Disconnect the connectors of all the wires between the ASSY MAIN BD DX and the main cabinet.

® Disconnect the connectors of all the wires between the shield case's filter board on the ASSY MAIN BD DX and the main cabinet.

® Remove the 2 wing bolts that fix the base (a wooden plate) of the ASSY MAIN BD DX.

WING BOLT (2) M4 X 25, flat washer used.-—~

flat washer use ae Disconnect all the connectors

g to the filter board.

BACK LID

Unlock.

Disconnect the connector.

ae | |ASSY MAIN BD DX

TRUSS SCREW (2) black M4 X 30

FIG. 17. 1a

Page 114

© raw out the ASSY MAIN BD DX from the

main cabinet. More than two workers must engage in this action. Note that the ASSY MAIN BD DX is heavy, and, if a single worker draws out it alone, he/she may damage the wires by snagging or catching the wires on other parts.

NOTE: If you remove the 3 screws and detach the shield case lid, you can access to the game board. This action is allowed, however, only for the Sega's service engineer. To perform work safely, Remove the 4 screws that fix the shield case use 2 or more workers. onto the base (a wooden plate), and detach the former from the latter. FIG. 17.1b

Remove the 2 screws each, and detach the shield case from the shield case brackets. Wrap the shield case with protective shipping materials, and contain it in a carton box. Send it for repairing.

Page 115
  • COMMUNICATION PLAY

For this game, up to 8 machines can be connected to allow up to 8 players to play simultaneously. In this instance, connecting the communication cable and setting for the communication play required.

18 - 1 INSTALLATION PRECAUTIONS

Before starting to work, ensure that the Power SW is OFF. Failure to observe this can cause electric shock or short circuit. Use care so as not to damage wirings. Damaged wiring can cause electric shock or short circuit. Do not touch undesignated places. Touching places not designated can cause ectric shock or short circuit. [his work should be performed by the Location’s Maintenance Man or erviceman. Performing work by non-technical personnel can cause electric shock hazard. When linking a number of machines, be sure to supply sufficient power for e corresponding number of machines. Be sure to secure per machine current as stated in this manual. Failure to observe this can cause a fire and an lectric shock accident. Due to the length of the communication cable, the distance in between the machines is limited. However, to avoid accidents, be sure to secure space in excess of 70 cm between the machines. In order to avoid personal injury, when separating the machine into each CABI, pay attention so as not to cause the PTV to fall down. To perform work safely and avoid serious accident such as the cabinet’s falling down, do not perform work in places where step-like grade differences, a ditch, or slope exist.

To perform work safely, be sure to secure the space corresponding to number of machines to be linked. Failure to observe this cause an accident.

IMPORTANT The optic fiber cable is used for the communication linkage. Excessive bending may damage the communication cable. Be very careful in this regard.

Since 2 or more machines are to be linked, sufficient power corresponding to the number of machines used need to be supplied. Note that as a standard, the per machine capacity should be 15A for the 100 ~ 120V area, and 7A for the 220 ~ 240V area.

Page 116

DISTANCE BETWEEN MACHINES

Be sure to secure space in excess of 70cm between machines.

18 - 2 CONNECTING THE COMMUNICATION CABLE

To enable the game machines to serve in a communication play, you must interconnect their game boards with communication cables (optical fiber cables). As for a wiring of the communication cables within the main cabinet (between the game board and the connector plate), Sega has completed it before it before shipping. Each connector plate has two connectors. Use them to sire the communication cables between one game machine to the next; thereby you can interconnect all the game boards. For this wiring, prepare in advance some standard accessories: flexible tube, 2 of 22, communication cable, and 2 sets fo number sticker.

® Turn off power and disconnect the plug. From the viewpoint of protecting, disconnect the power cord. TRUSS SCREW (4) black M4 X 16

@) Referring to Chapter 6, uncouple the

main cabinet from the PTV base/PTV/ billboard. Be careful not to damage the wires between them. Also be careful not to carelessly push the PTV base/PTV/billboard because it is easy to fall to the ground.

® Remove the 4 trusshead screws to detach

the connector box from the main cabinet.

CONNECTOR BOX PHOTO 18.2

Page 117

® Remove the 2 screws to detach the hole lid from the connector box. Depending on the number and arrangement of the interconnected game machines, you may remove either or both of the 2 hole lids. (Fig. 18.2a)

SCREW (2) black M3 X 8, wiflat & spring washers

ON ue EUD TRUSS SCREW (4) black M4X 16

FIG. 18.24

Page 118

® Attach CONNECTOR 22 to the both ends of FLEX TUBE. First, disassemble CONNECTOR 22 (Fig. 18.2 b).

© First pass the plastic nut through the flex tube. Otherwise, the following work can not be performed and therefore, be very careful of this point.

@ Install the holder and then the “insert” to the end of the flex tube by turning them as in bolts and nuts (Fig. 18.2 c).

Tighten the plastic nut to the connector. At this time, pass the communication cable through the flex tube ahead of time so as to allow the following work to be performed easily (Fig. 18.2 d).

(©) Install the flex tube into the CONNECTOR BOX HOLE. Insert the connector into the CONNECTOR BOX HOLE, put the seal washer through and fasten the metal nut (Fig. 18.2 e).

_PLASTICNUT CONNECTOR

HOareR,

INSERT

CONNECTOR

SEAL WASHER

_METAL NUT

C ‘ FLEX TUBE

SV

FIG. 18.26 FIG. 18. 2¢ FIG. 18.24

METAL NUT CONNECTOR BOX FIG. 18. 2¢

Page 119

Wire the communication cables. A wiring method (connecting which connector to which connector) varies depending on the number of the game machines to interconnect. Wire exactly according to the illustration below. For the number other than in the illustration, always connect the TX on one game machine to the RX of the other, and thereby make a loop of the communication cable finally. (Fig. 18.2 f)

a & Es zo

=

= wn

ae ra 5 © 2m w & EA ba wo

<= = ow

e ra

x ZN w & = w 2 w ,*

rd ry

« Ww o 2 © 2<- w & EA <= w 2M i e

< = w

e e Fa rd z a ZN 3, be e 4 <= w w Ww w

e t. 4 w w 3 E} Ze Ze

& é = = a S br}

FIG. 18.2f

Page 120

(®) Fix the connector box onto the main cabinet. Use the 4 trusshead screws that you removed previously. (P) Re-couple the main cabinet and the PTV base/PTV/billboard with each other. ® Arrange the game machines. See Chapter 7 for the precautions in transportation. Keep a space between the game machines as wide as possible.

Contact the adjusters of all the game machines to the floor. (Sec|6]3 ) ® Connect the power cords and the grounding cables. (Sec.[6 |4 ) ) Put the number stickers on the game machines. Facing the PTV screens, put the stickers '1''2''3' ... on the game machines from left to right. (Fig. 18. 2g)

Page 121

18 - 3 SETTING FOR COMMUNICATION PLAY

During communication play, if the test mode is not finished within 3 minutes on all the linked machines, the NETWORK CHECK cannot be performed, causing NETWORK ERROR.

IMPORTANT

Change the game setting for each seat in a manner so as to meet communication play. If the setting is not correct, communication play cannot be played.

SETTING FOR COMMUNICATION PLAY

@tun the linked machines' power on.

@) Cause all of the machines to enter the test mode. @ Select the SYSTEM ASSIGNMENTS.

@tun the linked machines' power on @) Cause all of the machines to enter the test mode @ Select the SYSTEM ASSIGNMENTS ® Perform the COMMUNICATION MODE setting in the SYSTEM ASSIGNMENTS screen. Set

one of the machines to MASTER and all others to SLAVE. Set to RELAY for exclusive use of LIVE Monitor.

SYSTEM ASSIGNMENTS,

CABINET TYPE IPLAYER ADVERTISE SOUND ON MONITOR TYPE HORIZONTAL DISPLAY MODE AUTOSCAN SERVICE TYPE COMMON > COMMUNICATION MODE MASTER EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

FIG. 18.34

® Activate the game test mode. (9-3)

© Select and open the GAME ASSIGNMENTS screen. Note that the screen looks different between the MASTER and SLAVE game machines.

@ Perform the SEAT NUMBER setting in the GAME ASSIGNMENTS screen. Set the machines sequentially to No.1, No.2, No.3, and so on as applicable starting from the extreme left facing the monitor's front side. Set every seat number correctly without duplication.

Page 122

GAME SETTINGS

LINK TYPE: STAND ALONE STEERING POWER: ***#*####### STEERING DIR.: REVERSE CARD SYSTEM: ENABLE BONUS GAME: 0

EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

FIG. 19.3 b

Cause all of the machines to exit from the test mode. After the test mode, the screens proceed to and display the NETWORK CHECK.

When a network-checking is finished, the system displays am advertisement screen. This means a successful completion of setting. If any seat number is duplicated, an error message appears on the screen. Normally the NETWORK CHECK takes less than one minute. If the screen does not proceed from the NETWORK CHECK screen, some sorts of errors such as incorrect setting, or incorrect connection or malfunctioning of the communication cable can be considered.

19 - 4 CAUTIONS TO BE HEEDED DURING COMMUNICATION PLAY

@ With a communication play, the ADVERTISE SOUND and GAME DIFFICULTY items can be set only on the MASTER game machine. New settings by the MASTER game machine become effective to all the interconnected game machines. If any setting is inadequate or if the communication cables are improperly connected, the system keeps displaying the network-checking screen or an error message. If this is the case, you cannot play the game. During communication play, if communication is interrupted due to some cause, the game is discontinued and the NETWORK CHECK screen is displayed. If one of the linked machines enters the test mode, all others display the NETWORK CHECK screen.

Machine's operation when linked for communication play alters comparing to that of when independently operated. Be careful of this point. As described above, some setting items must be set only on the MASTER game machine. They cannot be set on any SLAVE game machines or, if set, will not become effective. When any game machine is in a test mode, a network-checking screen appears on the other game machines interconnected for a communication play. While a guest is using any one of the interconnected game machines, therefore, do not activate a test mode even on the unused game machine.

Page 123
  • DESIGN RELATED PARTS

For the Warning Display stickers, refer to Section 1.

T a a a a

Page 124

ITEM NO. PART NO. DESCRIPTION

1999-1252DECAL MARQUEE SIDE LEFT

NOT SHOWN = 999-1253 DECAL MARQUEE SIDE RIGHT

2999-1237DECAL SIDE LEFT MONITOR,

NOT SHOWN = 999-1236 DECAL SIDE RIGHT MONITOR

3999-1241DECAL PEDESTAL LEFT

NOT SHOWN = 999-1242 DECAL PEDESTAL RIGHT NOT SHOWN = 999-1240 DECAL PEDESTAL TOP

4999-1254DECAL INSERT CLUB CARD (INSTR. #1)
5999-1238-L.DECAL LEFT TIRE BOX

NOT SHOWN = 999-1238-R DECAL RIGHT TIRE BOX

6999-1239DECAL LEFT, RIGHT TIRE TREAD
7999-1250DECAL NUMBER SHEET 1-8 SEAT (2 PER)
8999-1244DECAL REAR SECTION LEFT

NOT SHOWN = 999-1243 DECAL REAR SECTION RIGHT

9999-1248DECAL CHECKERBOARD LEFT

NOT SHOWN = 999-1249 DECAL CHECKERBOARD RIGHT

10999-1235MARQUEE CKT DLX
IL999-1251DECAL REAR SEAT
12999-1245DECAL REAR SECTION TOP
13999-1246DECAL REAR SECTION BACK
14999-1247DECAL CHECKERBOARD REAR PANEL TOP

NOT SHOWN = 999-1255 DECAL INSTRUCTIONS #2 (COIN TOWER) NOT SHOWN = 999-1256 DECAL NUMBER SHEET 1-8 PEDESTAL (2 PER)

Page 125
  • PARTS LIST G) Top Assy (D-1/1)

Y J Reece jrn RTT ED

Page 126

@) Top assy

ITEM NO.

woe

NOT SHOWN

IL NOT SHOWN NOT SHOWN PART NO.

LOC. PURCHASE NA NA SPGS5-2200-B SPG5-2200-A 999-1258 999-0167 SPG-2001 999-1257 999-1262 NA 999-1260 999-1273 999-1274 130-5162 130-5206 999-0169 999-1220 (D-2/2)

DESCRIPTION

FLUORESCENT FIXTURE 30 WATTS 36” 50” PTV COIN METER BRAKE PEDAL. ACCELERATOR PEDAL. CARD READER ASSY LEG LEVELER 1/2-13 X 3” (6 PER) STEERING WHEEL REAR SEAT COVER (GREEN) S/A; TUBE - BUTTERCUP YELLOW TIRE BOX LEFT, RIGHT ASSY FOOT PEDAL PLATE LEFT (METAL) ASSY FOOT PEDAL PLATE RIGHT (METAL) ASSY FOOT PEDAL PLATE REAR (2) (METAL) GULL BOX SPEAKER 80 OHM 8W SPEAKER 16CM 4 OHM 25W (2 PER) CASTER 160-2 1/2 #25188 SWIVEL (6 PER) SPEAKER GRILL (2 PER)

Page 127
  • assy PTV (NCR-0500) (D-1/2)
Page 128

(@) Assy PTV (NCR-0500)

ITEM NO. PART NO.

1 N/A 2 MGL-1150 3 NA 4 NCR-0600 5 DYN-0501 6 DYN-0502 7 RAL-0501

201 000-F00412 202 000-P00516-W 203 000-P00520-W 205 000-T00525-0B 206 068-552016-0B 207 000-T00520-0B 208 000-P00516-WB (D-2/2)

DESCRIPTION

PTV W/STICKER ASSY MASK ASSY BILLBOARD ASSY FRONT PANEL PANEL MOUNT BRKT L PANEL MOUNT BRKT R MASK HOLDER

M SCR FH M4 X 12 M SCR PH W/FS MS X 16 M SCR PH W/FS MS X 20 M SCR TH BLK MS X 25 FLT WSHR BLK 5.5-20 X 1.6 M SCR TH BLK MS X 20 M SCR PH W/FS BLK MS X 16

Page 129

G) ASSY BILLB

Page 130

@) ASSY BILLBOARD

ITEM NO.

RWNe PART NO.

NCR-0551 999-1235 NCR-0552 253-5457

421-7501-18

440-WS0002XEG 440-WS0012XEG

390-6659-32EX

280-5275-SR10

000-T00408-0C 000-P00430-S

068-441616 DESCRIPTION

BILLBOARD BOX MARQUEE CKT DLX BILLBOARD SASH FL HOLDER Locally supplied. STICKER FL32W Locally supplied. STICKER W POWER OFF ENG STICKER W HIGH TEMP ENG

ASSY FL32W EX W/CONN HIGH S CE Locally supplied. CORD CLAMP SR10

M SCR TH CRM M4 X8 M SCR PH W/S M4 X 30 Locally supplied. FLT WSHR 4.4-16 X 1.6 Locally supplied. (D-2/2)

NOTE

OTHERS USA OTHERS USA

OTHERS USA

OTHERS USA OTHERS USA

Page 131
  • ASSY FRONT PANEL (NCR-0600) (D-1/2)
Page 132
  • ASSY FRONT PANEL (NCR-0600) (D-2/2)

ITEM NO.

RWNY PART NO.

NCR-0601 EZT-0603 EZT-0604 EZT-0605

068-552016 050-F00500 DESCRIPTION

FRONT PANEL, SIDE BRKT BRKT UPPER BRKT LOWER

FLT WSRR 5.5-20 X 1.6 FLG NUT M5

Page 133

(S) ASSY MASK (MGL-1150)

ITEM NO. PART NO. DESCRIPTION

1MGL-1102TV MASK
2MGL-1151SLIT PLATE
3MGL-1152MASK SIDE HOLDER
201012-F00408-0BTAP SCR #2 FH BLK 4X8
202000-F00410M SCR FH M4 X 10
Page 134

(6) PTV WISTICKER NCR (NCR-0510)

ITEM NO. PART NO. DESCRIPTION

1999-1237STICKER PTV SIDE L
2999-1236STICKER PTV SIDER
101200-5788-31PROJECTION DSPL T SOTYPE 31K
Page 135

@) ASSY PTV BASE (POD-0550)

ITEM NO. PART NO. DESCRIPTION

1POD-0551PTV BASE
2SCR-1008NUT PLATE FOR CASTER
3ARC-1006LEG BRACKET
4117-5233PLATE LEG BRACKET BLACK.
6POD-1008NUT BRKT
101999-0169CASTER 160-2 1/2”
102999-0167LEG ADJUSTER BOLT 1/2-13 X 3”
201011-T03512TAP SCR TH 3.5 X 12
202Loc. PurchaseHEX BLT W/S BLK M6 X 25
203Loc. PurchaseHEX BLT W/FS M6 X 25
204Loc. PurchaseHEX NUT BLK M16
205000-P00520-WM SCR PH W/FS MS X 20
Page 136

ASSY SUB-CABI (NCR-1001) (0-1/2)

yg an Res yg a ay Ww

Of

jo ghee ae / y / q P Ga t D718 (039 a i oe

Py 5 Jn hb 4 sy =} g on ss 8 thes \ = 7 14115 9102 BE

Page 137

ASSY SUB-CABI (NCR-1001)

ITEM NO.

2u1 PART NO.

NCR-1090 STR-1070 NCR-1080 NCR-1002 NCR-1003 NCR-1004 NCR-1005 NCR-1006 NCR-1007 NCR-1012 NCR-1013 NCR-1024 NCR-1025 ARC-1006 999-1042 253-5460-01 DP-1148X 117-0062 117-5098 NCR-1004-B APC-1090 NCR-1005-B

999-0169 999-0167 220-5575 117-5402-06-91

000-T00420-0B FAS-110010 030-000630-SB 030-000625-WB 050-H01600 079-000008 O11-F03516 011-T00312 000-T00430-0B 030-000830-S 060-F00800 000-T00416-0C

600-6275-0300 600-7009-3000 600-7141-250 (D-2/2)

DESCRIPTION

AC UNIT FAN UNIT ASSY CONNECTOR PLATE WOODEN CABINET FRONT LID SIDE LID BACK LID SUPPORT PLATE LOWER A HOLD PLATE A SUPPORT PLATE LOWER B HOLD PLATE B STEP GUARD PLATE SIDE STEP PLATE LEG BRACKET PLATE LEG BRACKET BLACK AIR VENT BLACK LKG TNG PLATE LOCK RETAINER TNG RETAINER PLATE STICKER SIDE LID CORNER GUARD STICKER BACK LID

CASTER 160-2 1/2” LEG ADJUSTER CAM LOCK MASTER W/O KEY EARTH TERMINAL PLATE 6P.

M SCR TH BLK M4 X 20 TAP SCR FH #1 BLK 3 X 10 HEX BLT BLK W/S M6 X 30 HEX BLT W/FS BLK M6 X 25 HEX NUT M16 SCR NAIL THH STNLS 1.5 X 16 TAP SCR FH 3.5 X 16 TAP SCR TH 3 X 12 M SCR TH BLK M4 X 30 HEX BLT W/S M8 X 30 FLT WSHR M8 M SCR TH CRM M4 X 16

ASSY FIBER CABLE 5 0300CM ASSY RGB CA D-SUB 15P 3000MM CABLE JVS TYPE A-B 250CM

Page 138

@) AC UNIT

{-

ITEM NO. PART NO.

1 999-1043 NOT SHOWN DYN-0402 NOT SHOWN 421-8202

101 999-1044 104 999-0676 103) ,

° @ C3

FRONT SIDE

DESCRIPTION

AC BRKT NOISE FILTER BASE STICKER EARTH MARK

AC INLET PANEL TYPE SW ROCKER J8 V-B

Page 139

FAN UNIT (STR-1070)

ITEM NO. PART NO. DESCRIPTION

1105-5340-01FAN BRKT LONG
101LOC. PURCHASEFAN AC120V

102 601-8543

201000-P00312-WM SCR PH W/FS M3 X 12
Page 140

q@) ASSY CONNECTOR PLATE (NCR-1080)

ITEM NO. PART NO.

NCR-1081 421-7515

211-5479-01

000-P00312-W DESCRIPTION

CONNECTOR PLATE STICKER FIBER CABLE TX/RX

CONN OPT JOINT

M SCR PH W/FS M3 X 12

Page 141
  • FAN UNIT (NCR-1070)

ITEM NO. PART NO.

NCR-1071

260-0011-02 601-8543

000-P00312-W 050-H00300 060-S00300 060-F00300 DESCRIPTION

FAN BRKT

FAN AC120V FAN GUARD

M SCR PH W/FS M3 X 12 HEX NUT M3 SPR WSHR M3 FLT WSHR M3

Page 142

(3 swunit

SERVICE FRONT SPKR

ITEM NO. PART NO. DESCRIPTION

1LOC. PURCHASECOIN METER 6 VOLTS
2LOC. PURCHASEPUSH BUTTON SW
3LOC. PURCHASE5 K POTENTIOMETER & VOLUME KNOB
Page 143

ASSY CTRL PNL (NCR-2000)

ITEM NO. PART NO.

1 SRT-2150 2 NCR-2006 3 SPG-2001 4 SPG-2002 DESCRIPTION

ASSY SW PLATE STEERING COLLAR STEERING WHEEL STEERING EMBLEM

Page 144
  • ASSY SW PLATE (SRT-2150)

O START O

O VIEW ‘ @)

ITEM NO. PART NO. DESCRIPTION

1SRT-2151SW PLATE
101509-5838-YSW PB LWIL-15Y-TK1670
102509-5495-05PUSH BUTTON BLUE
301600-7008-079WIRE HARN BUTTON
Page 145

(16) ASSY CTRL SHAFT

OOS,

ITEM NO. PART NO. DESCRIPTION

1999-1291STEERING BASE CKT
2NCR-2005STEERING SHAFT
3111-1131COUPLING MJT-40K-BL 16-20 (FRI)
4DUT-2106STOPPER RUBBER
5DUT-2105STOPPER BOLT M10
6NCR-2003BEARING HOLDER
7100-5240BEARING FA130
8100-5377BEARING 30
101030-001435M14 X 35 HEX BOLT
102060-S01400SPR WASHER M14
103060-F01400FIT WASHER M14
104060-F00800M8 FIT WASHER
105030-000820-SM8 X 20 HEX BOLT W/S
Page 146
  • STEERING MOTOR UNIT (NCR-2100) (D-1/2)

M6 X 5.8 Nem M8 X 18 Nem M3 X 0.76 Nem M4 X 1.8 Nem

anya (ss,

DEO)

Page 147
  • STEERING MOTOR UNIT (NCR-2100) (D-2/2)

ITEM NO. PART NO.

1 FRI-2101 2 FRI-2102 3 NCR-2101 4 FRI-2104 5 SPG-2504 6 SPG-2505 7 SPG-2506 8 FRI-2105 9 SPG-2453 10 ASK-3502 11 ASK-3503 12 DYN-1270 13 SLC-1130 14 SPG-2454 15 FRI-2106

101 350-5448-01 102 100-5112 103 601-8966 104 601-6172 105 601-6959 106 601-9173 107 220-5373 220-5484 108 310-5029-F20 109 280-0419 110 280-5009-01

201 028-A00408-P 202 028-A00308-P 203 065-S012S0-Z 204 065-S020S0-Z 205 000-P00408-W 206 000-P00412-W 207 030-000612-S 208 060-F00600 209 030-000820-S 210 030-000840-S 21 068-852216 212 060-F00800

301 NCR-60055 DESCRIPTION

MECHA BASE BASE LID MOTOR SHAFT SHAFT LOCK PLATE PULLEY 20 SSM PULLEY 60 SSM MOTOR BRKT VR BRKT KEY 4X4X 40 MOTOR SPACER MOTOR COLLAR STOPPER KEY ADJUST RING MOTOR SHAFT COLLAR VR BASE

SERVO MOTOR 500W NEW BEARING 17 GEAR HOLDER GEAR 48 GEAR 64 TIMING BELT VOL CONT B-SK VOL CONT B-SK OHM SUMITUBE F F 20MM HARNESS LUG CORD CLAMP 21

SET SCR HEX SKT CUP P M4 X 8 SET SCR HEX SKT CUP P M3 X 8 STP RING BLK OZ S12 STP RING BLK OZ S20 MSCR PH W/FS M4 X 8 M SCR PH WIFS M4 X 12 HEX BLT W/S M6 X 12 FLT WSHR M6 HEX BLT W/S M8 X 20 HEX BLT W/S M8 X 40 FLT WSHR 8.5-22 X 1.6 FLT WSHR M8

WIRE HARN HANDLE VR

Page 148

ASSY ACCEL&BRAKE (SPG-2200) (D-1/2)

Page 149

ASSY ACCEL&BRAKE (SPG-2200) (D-2/2)

ITEM NO. PART NO. DESCRIPTION

1SPGS-2201-ABASE ACCELERATOR

SPGS5-2201-B BASE BRAKE

2SPG-2202ACCEL PEDAL
3SPG-2203BRAKE PEDAL
4SPG-2204ACCEL SPRING
3SPG-2205BRAKE SPRING
6SPG-2206SHAFT
7SPG-2207ACCEL GEAR
8SPG-2208BRAKE GEAR
9SPG-2209NEUTRAL STOPPER
10SPG-2210VR PLATE ACCEL
11SPG-2211VR PLATE BRAKE
12SPG-2212AMPL GEAR
13SPG-2213GEAR SHAFT
14SPG-2214STOPPER
15SPG-2215RUBBER CUSHION

NOT SHOWN = 999-1260 PEDAL PLATE LEFT NOT SHOWN = 999-1273 PEDAL PLATE RIGHT NOT SHOWN 999-1274 PEDAL PLATE REAR (2)

19SPG-2219GEAR STAY
20SPG-2220WSHR
21SPG-2221NEUTRAL STOPPER D
101100-5263BEARING 12
102220-5484VOL CONT B-SK OHM

220-5373 VOL CONT B-5K

104601-7944GEAR 15
105310-5029-F15SUMITUBE F F 15MM
106280-0419HARNESS LUG
201028-A00304-PSET SCR HEX SKT CUP P M3 X 4
202020-000520-0ZHEX SKT H CAP SCR BLK MS X 20
203000-P00420M SCR PH M4 X2
204000-P00508-WMSCR PH W/FS MS X 8
205000-T00408-0CM SCR TH CRM M4 X 8
206FAS-450005SPR PIN BLK OZ 6 X 10
207000-P00405MSCR PH M4 X 5
208FAS-000001M SCR TH CRM M3 X 6
209050-H00500HEX NUT M5
210060-F00400FLT WSHR M4
301600-6840WIRE HARN ACCEL&BRAKE
Page 150

ASSY SEAT (NCR-2400) (D-1/2)

M4 Sonic Lock Portion: 0.9N¢m MB8 Others: 19.9Nem

Page 151

ASSY SEAT (NCR-2400)

ITEM NO. PART NO.

1 999-1257 2 NCR-2402 3 NCR-2403 4 NCR-2404 5 SRT-2402 6 999-1048 9 FRI-3309 12 STC-1608 13 STC-1609 15 DUT-2205 16 STC-1607 17 INY-1302-B

103 280-5297 104 130-5162 106 280-5009-01 107 280-5275-SR10 108 601-6981-009 109 601-6563-225

201 030-0008 16-S 202 030-000850-S 203 050-H00800 204 060-S00800 205 068-852216 206 000-T00408-0B 207 000-P00410-W 208 000-T00516-0B 209 000-T00616-0B 210 000-P00408-S 2u1 060-F00400 212 050-U00400 213 030-000855-S 214 012-P00412 (D-2/2)

DESCRIPTION

SEAT BACK COVER UPPER SEAT LOWER SEAT SEAT BASE SEAT FRAME TURTLE COVER CABLE BEAR BRKT SPEAKER NET L SPEAKER NET R SHAKER BASE REAR SP MOUNT BRKT MASK CUSHION SIDE

SCRIVET 8 1K31 GULL BOX SPEAKER 80HM 8W CORD CLAMP 21 CORD CLAMP SR10 CABLE BEAR L=009 BUSH 2.4T

HEX BLT W/S M8 X 16 HEX BLT W/S MB X 50 HEX NUT M8 SPR WSHR M8 FLT WSHR 8.5-22 X 1.6 M SCR TH BLK M4 X 8 M SCR PH WIFS M4 X 10 M SCR TH BLK MS X 16 M SCR TH BLK M6 X 16 MSCR PH W/S M4 X 8 FLT WSHR M4 U NUT M4 HEX BLT W/S M8 X 55 TAP SCR #2 PH 4 X 12

Page 152

CARD READER ASSY (999-1258)

ITEM NO. PART NO.

1 253-5512 2 601-11039 3 999-1259 4 999-1272 NOT SHOWN _ 601-11051-01 NOT SHOWN _ 6017-11050 DESCRIPTION

CARD GUIDE CARD R/W UNIT CR-1231R. OPTIC UNIT OPTIC BRACKET CARDS (200 PACK) CLEANING KIT

Page 153

@i) ASSY MAIN BD DX

ITEM NO. PART NO.

840-0062D-01 2 400-5368-07512 3 400-5397-01 DESCRIPTION

ASSY CASE NAT CKT USA SW REGU LCA75S-12 (Used for Card Reader) SW REGU DC 3.3V 12A 5V 10A 12V 2A

Page 154

@2) ASSY AMP BD

ITEM NO. PART NO.

LOC. PURCHASE 838-13616 838-13844 LOC. PURCHASE 838-13578 ARwWN DESCRIPTION

FAN AC120V AUDIO POWER AMP 2 CH PCB I/O CONTROL BD 2 FOR JVS FUSE BLOCK PWR AMP 2CH & MIXER

Page 155

BE iw A

NOTE: 1. MAKE SURE THAT THERE IS NO WIRING, ETC.

IN THE SLASH MARK PORTIONS.

  • Set all the DIP switches (837-13844 (AB) and 838-13366 (4C)) to OFF. @3) ASSY ELEC (NCR-4200) (D-1/2)
Page 156

@3) ASSY ELEC (NCR-4200)

ITEM NO. PART NO.

1 NCR-4201 2 NCR-4202 3 837-13844 4 838-13366 5 838-12912-01 7 421-7468-01

102 998-0135 103 117-5225

104 512-5046-15000 105 310-5029-K20 106 280-5009-01 108 601-0460

201 011-T00316 202 011-T00325 203 000-P00516-W 204 000-P00416-W 205 011-T03512 206 011-F00312 (D-2/2)

DESCRIPTION

WOODEN ELEC BASE C.P.BRKT /O CONTROL BD 2 FOR JVS FRI DRIVE BD SRT SERVO MOTOR DRIVE BD NEW STICKER C.P W/PIC

POWER TRANSFORMER ER-501 FUSES 1-6.25 A SLOW BLOW 2-3A SLOW BLOW 1-1SA SLOW BLOW C.P 15000MA CE UL SUMITUBE F K 20MM CORD CLAMP 21 PLASTIC TIE BELT 100 MM

TAP SCR TH 3 X 16 TAP SCR TH 3 X 25 MSCR PH W/FS MS X 16 M SCR PH W/FS M4 X 16 TAP SCR TH 3.5 X 12 TAP SCR #1 FH 3 X 12

Page 157
  • WIRE COLOR CODE TABLE

THE WIRE COLOR CODE is as follow:

A PINK B SKY BLUE

Cc BROWN

D PURPLE E LIGHT GREEN

Wires other than those of any of the above 5 single colors will be displayed by 2 alphanumeric characters.

1 RED 2 BLUE 3 YELLOW 4 GREEN 5 WHITE 7 ORANGE 8 BLACK 9 GRAY

If the right-hand side numeral of the code is 0, then the wire will be of a single color shown by the left-hand side numeral (see the above).

Note 1: If the right-hand side alphanumeric is not 0, that particular wire has a spiral color code. The left-hand side character shows the base color and the right-hand side one, the spiral color.

<Example> 51 oe WHITE / RED

RED WHITE

Note 2: The character following the wire color code indicates the size of the wire.

U: AWGI16

K: AWGI8

L: AWG20 ‘None: AWG22

Page 158

Warranty

Your new Sega Product is covered for a period of 90 days from the date of shipment. This certifies that the Printed Circuit Boards, Power Supplies and Monitor are to be free of defects in workmanship or materials under normal operating conditions. This also certifies that all Interactive Control Assemblies are to be free from defects in workmanship and materials under normal operating conditions. No other product in this machine is hereby covered.

Sellers sole liability in the event a warranted part described above fails shall be, at its option, to replace or repair the defective part during the warranty period. For Warranty claims, contact your Sega Distributor.

Should the Seller determine, by inspection that the product was caused by Accident, Misuse, Neglect, Alteration, Improper Repair, Installation or Testing, the warranty offered will be null and void.

Under no circumstances is the Seller responsible for any loss of profits, loss of use, or other damages.

This shall be the exclusive written Warranty of the original purchaser expressed in lieu of all other warranties expressed or implied. Under no circumstance shall it extend beyond the period of time listed above.

Page 159

SEGA ENTERPRISES, INC. (USA)

45133 Industrial Drive Fremont, CA 94538 (415) 701-6580 phone (415) 701-6594 fax