Kid Niki Radical Ninja Conversion Kit (780-0052-00)
Kid Niki - Radical Ninja (World) (Irem, 1986) · Manual · 30 pages · 7 sections · original scan
CONVERSION KIT
installation « service manual
fa DATA EAST USA, INC. D ag 470 Needles Drive San Jose, CA 95112 780-0052-00
WARNING
This equipment generates and uses radio frequency energy and
if not installed and used properly, i-e., in strict accordance with
the instructions manual, may cause harmful interference to radio the limits for a Class A computing device persuant to Subpart J of
communications. It has been tested and found to comply with
Part 15 of FCC Rules, which are designed to provide reasonable ‘protection against such interference when operated in a commercial environment.
Operation of this equipment in a residential area is likely to cause required to take whatever measures may be required to correct
interference in which case the user at his own expense will be
the interference.
Federal law provides severe civil and
criminal penalties for the unauthorized
reproduction, distribution, or exhibition of copyrighted audiovisual works and video games. The Federal Bureau of Investigation investigates allegations of criminal copyright infringement.
KID NIKI-RADICAL NINJA
INSTALLATION AND SERVICE MANUAL
CONVERSION KIT MODEL NUMBER 1US27K
TABLE OF CONTENTS
GENERAL INFORMATION
a. Warnings and service information...........-.e.eeeeeeeeee i,
Watratty, Dn Botmatno ners csc os cs iempeweislionsiee «210 eianmcsieieme sees 2
Checking your Ritts «oc. cineieeiecic net eleva eiejserie bd dew ciewle-wereee 6c 3
General conversion requirementS......cccsccencreccscceees 4
SPECIFIC INFORMATION
a.
b.
c. Self test information... ...eccsccsecncceescccesscsrcenes 5
Sound volume adjustments. .cc:0.1 ssw ewwswe emmys newer eeneies! 6
Operator selectable options...........-.eee eee eee ee eeeee 6
INSTALLATION INSTRUCTIONS
a. Conversion preparations... occ ceccisiicdcecs wecinmewsic nese 8
b. Installation procedures..
6 BGge iconnector pan“ tcrcasisie ws. ov ovacaresenereve ens 0 ecemrnmecereye nea
d. Specific wiring diagrams........... Se eT eT 13
PCB SCHEMATICS a reecc.ssae ia sis cecninieesratiyd 9 6 a aslalteaumend #6 6 o metnsareragts 14
© 1987 DATA EAST USA, INC. 470 NEEDLES DR. SAN JOSE, CA. 95112 (408) 286-7074
- GENERAL INFORMATION
a. Warnings & service information.
FCC WARNING:
This equipment generates and uses radio frequency energy and if not installed and used properly, ie., in strict accordance with the instructions manual, may cause harmful interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment.
Operation of this equipment in a residential area is likely to cause interference in which the user at his own expense will be required to take whatever measures may be required to correct the interference.
FBI WARNING:
Federal law provides severe civil and criminal penalties for the unauthorized reproduction, distribution, or exhibition of copyrighted audiovisual works and video games.
The Federal Bureau of Investigation investigates allegations of criminal copyright infringement.
COPYRIGHT NOTICE:
Copyright 1987 by Data East Corporation, all rights reserved. Kid Niki, Radical Ninja is manufactured by Data East under license from Irem Corporation.
REPLACEMENT PARTS AND SERVICE:
To obtain replacement parts or technical assistance, contact the Data East distributor in your area. If you require further technical assistance, you may contact Data East's Service department during the hours of 8:00 a.m. to 5:00 p.m. Pacific time at (408) 286-7074.
KID NIKI INSTALLATION & SERVICE MANUAL PAGE 1
b. Warranty information.
DATA EAST LIMITED WARRANTY
Data East USA, Inc., ("Seller"), warrants only to the initial purchaser of its products that the items listed below are free from defects in material and workmanship under normal use and service for the warranty period specified:
Printed Circuit Boards (game logic) 90 days
No other parts of Seller's product are warranted.
Warranty periods are effective from initial date of shipment from Seller to its authorized distributors.
Seller's sole liability shall be, at its option, to repair or replace products which are returned to Seller during the warranty periods specified, provided:
- Seller is notified promptly upon discovery by purchaser that stated products are defective.
- Such products are properly packaged and then returned freight prepaid, to Seller's plant.
This warranty does not apply to any parts damaged during shipment and/or due to improper handling, or due to improper installation or usage, or alteration. In no event shall the Seller be liable for any anticipated profits, loss of profits, loss of use, accidental or consequential damages or any other losses incurred by the customer in connection with the purchase of a Data East USA, Inc., product.
WARRANTY DISCLAIMER
EXCEPT AS SPECIFICALLY PROVIDED IN A WRITTEN CONTRACT BETWEEN SELLER AND PURCHASER, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
PAGE 2 KID NIKI INSTALLATION & SERVICE MANUAL
c. Checking your kit.
Your Data East conversion kit contains all of the components required for installation in most color upright video game cabinets. Before beginning, check the contents of your conversion kit for the following materials:
(1)
(1)
(1)
(1)
(1)
(1)
(2)
(1)
(2)
(2)
(2)
(1)
(1)
Verify that your kit is complete before going further. Kid Niki pcb set
EMI filter PCB, Irem to Deco
Main harness, conversion kit
Marquee plex, Kid Niki
Monitor underlay card, Kid Niki
Control panel overlay, generic kit
Side decal, generic kit
Joystick assy, 4/8 way
Pushbutton assy, Black
Pushbutton assy, Yellow
Pushbutton assy, White
Installation & Service manual
FCC Warning Label 510-0095-00
520-0087-00
036-0013-01
830-0029-00
810-0020-00
800-0021-01
820-0036-00
450-0009-00
350-0016-00
350-0016-04
350-0016-09
780-0052-00
406-0003-00
KID NIKI INSTALLATION & SERVICE MANUAL PAGE 3
d. General conversion requirements.
This Data East conversion kit is designed to be installed into an existing video game cabinet. All necessary components and graphics have been supplied to make the results of this conversion look and play like a new upright game. There are several requirements to consider when selecting a game to convert. They are as follows:
MONITOR: RGB, NEGATIVE COMPOSITE SYNC, HORIZONTALLY MOUNTED
POWER SUPPLY: + 5 VOLTS AT A MINIMUM OF 7 AMPERES. (Kid Niki pcb set draws 4.6 amps)
+ 12 VOLTS AT A MINIMUM OF 1 AMPERE. (Kid Niki pcb set draws .79 amps nominal)
When selecting a game to convert, make sure that the coin acceptors are functional, the monitor and power supply work well, and the cabinet is structurely sound. There is nothing more frustrating then installing a new conversion kit and discovering that it will not come up due to a faulty monitor or power supply. I know...the first thing you will suspect is the new Logic PCB, right? Save yourself some time and money by making sure the original game works before you install a KTEs
It it mandatory that the cabinet be wired to conform with all National and Local Electrical Code requirements before the conversion is attempted. The system must have adequate noise filtering on the AC line to prevent unwanted conducted radio frequency interference. Adequate is defined as a filter having both common mode and differential mode filtering with a current capacity of at least 1 1/2 amperes.
According to the FCC and/or other regulatory agencies, every video game must be clearly labeled with the name and address of the Original Manufacturer, Date of Manufacture (or serial number), Voltage Rating, Current Rating, Suitability for indoor or outdoor use, and Model Number. In addition, the FCC requires that after conversion, the unit must be labeled with a suitable warning stating that radio frequency interference may result from use in a residential area. An acceptable
IT IS THE RESPONSIBILITY OF THE PERSON PERFORMING THE CONVERSION TO COMPLY WITH ALL LABELING REQUIREMENTS.
PAGE 4 KID NIKI INSTALLATION & SERVICE MANUAL
2- SPECIFIC INFORMATION
A. Self test information.
The Kid Niki game has a self test mode that checks out the system hardware. To enable this test, switch number 8 on Dipswitch 2 to the "ON" position and apply power to the game. The following tests will appear on the screen:
RAM test ROM test I/O Port test DIP Switch test Sound test Character test Color test Beam adjustment test OIA PWN
As soon as power is applied with the Test Mode selected, tests 1 and 2 are started. Use the-1 Player joystick up/down directions to select test item from the menu and the 1 Player Start button to begin test.
To return to the attract mode, remove power, switch number 8 of Dipswitch 2 to the "OFF" position, and apply power once again.
TEST PROCEDURES:
TURN "ON" 8 OF DIP SW 2
TURN ON POWER SWITCH]
RAM, ROM TESTS START
CHARACTER TEST|
‘YES. TURN OFF FINISH TURN 8 OF DIP SW 2 POWER SWITCH BACK TO "OFF"
KID NIKI INSTALLATION & SERVICE MANUAL PAGE 5
B. Sound volume adjustment.
The sound volume level is adjustable by turning the potentiomenter VR1 on the main logic pcb (see figure 1) until the desired volume level is attained.
C. Operator selectable options.
The Kid Niki game contains operator selectable coinage,
on the main logic pcb (see figure 1). the available options. bonus, These options are accessed by the two 8 position dipswitches located The following tables outline etc.
| PIPSWITCH 1 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
NUMBER OF OFF OFF LIVES ON OFF OFF ON ON ON DIFFICULTY OFF ON
| EXTRA LIFE | 50000 PTS: | OFF | ||
| GIVEN AT: | 80000 PTS: | ON | ||
| COIN | COIN 1 COIN=1 PLAY: | OFF OFF | | | |
| MODE | A | 2 COIN=1 PLAY: | ON | OFF |
| 2 | 3 COIN=1 PLAY: | OFF ON | ||
| 5 COIN=1 PLAY: | ON | ON |
SW3 OF [COIN 1 COIN=2 PLAY: OFF OFF
| DIPSW 2| | B | 1 COIN=3 PLAY: | ON | OFF |
| ON | 1 COIN=5 PLAY: | OFF ON |
1 COIN=6 PLAY: ON__ON
| COIN | 1 COIN=1 PLAY: | OFF OFF OFF OFF | |||
| MODE | 2 COIN=1 PLAY: | ON | OFF OFF OFF | ||
| 1 | 3 COIN=1 | OFF ON | OFF OFF | ||
| 4 COIN=1 | ON | ON | OFF OFF | | ||
| 5 COIN=1 | OFF OFF ON | OFF | | |||
| 6 COIN=1 | ON | OFF ON | OFF | | ||
| SW3 OF | 1 COIN=2 | OFF ON | ON | OFF | | |
| DIPSW 2 | 1 COIN=3 | ON | ON | ON | OFF | |
| OFF | 1 COIN=4 | OFF OFF OFF ON | | |||
| 1 COIN=5 | ON | OFF OFF ON | |||
| 1 COIN=6 | OFF ON | OFF ON | | |||
| 2 COIN=3 | ON | ON | OFF ON | | ||
| 3 COIN=2 | OFF OFF ON | ON | | |||
| 5 COIN=3 | ON | OFF ON | ON | | ||
| 8 COIN=3 | OFF ON | ON | ON: | ||
| FREE | ON | ON | ON | ON } |
PAGE 6 KID NIKI INSTALLATION & SERVICE MANUAL
| DIPSWITCH 2 | 1 | 2 | 3 | 4 | 5 | 5 | z | 8 |
FLIP PICTURE NO: OFF YES: ON CABINET TYPE TABLE: OFF UPRIGHT: ON
| | COIN MODE | MODE 1: | OFF | |
| 1 | MODE 2: | ON | |
| GAME | NO; | OFF | |
| | REPETITION | YES: | ON | |
| CONTINUE MODE | YES: | OFF | |
| (BUY-IN) | NO: | ON | |
| | FREEZE PICTURE | NO: | OFF | |
| | | MODE | YES: | ON |
| | NO DEATH MODE | NO: | OFF | |
| L | YES: | On | |
| | DIAGNOSTIC TEST | NO: | OF | |
| L | MODE | YES: | ON |
- SELECT COIN MODE 1 FOR GAMES WITH ONE COIN SELECTOR OR IF TWO COIN SELECTORS WITH THE SAME COIN/CREDIT VALUES ARE DESIRED.
- SELECT COIN MODE 2 IF TWO COIN SELECTORS OF DIFFERENT COIN/CREDIT VALUES ARE DESIRED.
- TO ACTIVATE FREEZE PICTURE MODE, SWITCH 6 OF DIPSWITCH 2 ON. THE GAME WILL PLAY NORMALLY. TO FREEZE PICTURE, PRESS 2 PLAYER START BUTTON. TO CONTINUE, PRESS 1 PLAYER START BUTTON.
- GAME REPETITION ALLOWS THE GAME PLAY TO WRAP AROUND TO THE BEGIN- NING WHEN ALL SCENES ARE COMPLETED. DISABLE TO STOP GAHE AT END.
C Coy ey \—— o1pswitcn 2 [|
DIPSWITCH 1
p—— SOUND VOLUME
FIGURE 1
KID NIKI INSTALLATION & SERVICE MANUAL PAGE 7
- INSTALLATION INSTRUCTIONS
a. Conversion preparations.
Performing a few simple tasks when preparing a game to be converted can save you much time and effort when you are installing the conversion kit. This section will cover the basic procedures to follow when preparing your game.
FIND THE WIRING DIAGRAM FOR THE GAME TO BE CONVERTED! You will need to identify the required DC power supply output wires, and the monitor video and sync wires. Note the color coding of these wires or better yet, label each one as to their function. This conversion kit contains a new Main Harness, but you may need to splice into the existing power supply and monitor wires.
Remove the existing game harnesses that will not be utilized in the final conversion. NOTE: This conversion kit only requires modification of the secondary (DC from power supply) and I/O (control panel and coin) sections of the original wiring. DO NOT REMOVE OR MODIFY THE PRIMARY AC WIRING. The primary AC wiring has been designed and built to UL and FCC regulations and must not be modified.
Remove the existing game logic boards. Remove all decals and/or paint over existing cabinet graphics. Repair any cabinet damage.
Remove the monitor plex (or glass). If your plex has silkscreened artwork on it, you will need to strip it off or replace with a clear plex cut to the same size. Use your original plex as a template when cutting the new Underlay Card down to size.
Remove the marquee plex. Use this plex as a template when cutting the new Marquee plex down to size.
Remove the control panel from the cabinet and strip it down. The game is now ready to be converted!
© O® IPL JUMP SwoRD a
2PL. ©
FIGURE 2
PAGE 8 KID NIKI INSTALLATION & SERVICE MANUAL
b. Installation procedures.
Control Panel: This is never any fun, so lets do it first and get it out of the way. Examine the suggested control panel layout drawing (fig. 2) and see what holes you will have to add and/or plug.
Install the control panel overlay by peeling off the paper backing and carefully lowering it down on to the panel. Smooth it out starting from the center and work your way out to the edges, removing all of the trapped air pockets. Using a sharp blade, cut out all of the required holes and mount the controls as shown in the layout drawing (fig. 2). Mount the completed control panel to the cabinet.
PCB Set: Mount the Kid Niki pcb set into the cabinet. We recommend mounting the pcb to’ a side wall to allow for adequate convection cooling. Plug the EMI Filter pcb onto the logic pcb's edge connector.
Power Supply Wiring: Plug the Main Harness onto the edge connector of the EMI Filter pcb and route the power supply wires neatly to the power supply. For best results, these wires should be routed in such a way as to keep the overall length to a minimum. Use a minimum of two (2) wires EACH for the +5 volt and Ground wires from the Power Supply to the pcb set. The +12 volt wire is not critical, one (1) wire 1s adequate. Terminate these wires as required.
Player Control Wiring: Route the player control wires to their proper destinations, cut to proper length, and terminate as required. See Specific Wiring Information for hook up details.
Monitor Wiring: As mentioned in the Conversion Requirements, this pcb set outputs NEGATIVE COMPOSITE SYNC to the monitor. If your monitor does not support Composite Sync, hook the Sync wire to the negative Horizontal Sync input. This method will work on most monitors, however some Electrohome models require that Sync be tied to both the negative Horizontal and negative Vertical inputs for proper operation. Contact your distributor if you are uncertain as to the proper hook up procedures for your monitor.
KID NIKI INSTALLATION & SERVICE MANUAL PAGE 9
b. Installation procedures (continued)
Coin Counter(s): The Coin Counter(s) can be 5 volt or 12 volt units as the pcb set utilizes an Open Collector output driver circuit. See Specific Wiring Information for hook up details.
Graphics: Install the Underlay Card. This card will rest directly under the clear monitor plex (or glass). Mount the new Marquee Plex in place at this time. Apply the side decals, being careful to remove all air pockets. MANDATORY: Install the FCC warning label to the back of the cabinet to complete the installation procedures!
The Big Test: Before applying power to the game, verify that the wiring is correct.
DISCONNECT THE HARNESS EDGE CONNECTOR NOW!
With the harness edge connector disconnected, apply power and measure the +5 volt level in respect to ground AT THE EDGE CONNECTOR OF THE MAIN HARNESS WITH A DIGITAL MULTI-NETER. Refer to the edge connector pinout on page 12. Adjust the power supply to get a 5.2 volt reading at this point. Check the +12 volt level and the -5 volt (-5 volts may not be required) level in the same manner. REMOVE POWER FROM THE GAME AND WAIT 2 MINUTES FOR THE POWER SUPPLY TO DISCHARGE.
RE-INSTALL THE HARNESS EDGE CONNECTOR NOW!
Apply power to the game. The game's attract mode video should appear on the screen. Examine the video for correct appearance. Adjust the controls on the monitor to get the optimum picture possible.
Well, coin it up and play it! Check for proper controls, video, and sound.
PAGE 10 KID NIKI INSTALLATION & SERVICE MANUAL
C. Edge connector pin-out
The Kid Niki pcb has a 44 pin edge connector. Data East supplies a suitable EMI filter pcb with each game to make the game comply with FCC regulations and adapt to the Data East harness pin-out configuration.
The diagram below represents the IREM pin-out used on the actual game pcb, the one on page 12 is the Data East type harness pin-out used on the EMI filter pcb.
IREM EDGE CONNECTOR PIN-OUT
KID NIKI PCB EDGE CONNECTOR, CN-3
COMPONENT SIDE SOLDER SIDE PIN NUMBER
| GROUND | 1 | GROUND | |
| GROUND | 3 | 4 | GROUND |
5 6
| COIN COUNTER A | 7 | 8 | |
| 1P CONTROL LEFT | 9 | 10 | 2P CONTROL LEFT |
| 1P CONTROL RIGHT | 11 | 12 | 2P CONTROL RIGHT |
| 1P CONTROL PUSH 1 | 13 | 14 | 2P CONTROL PUSH 1 |
| i PLAYER START | 15 | 16 | 2 PLAYER START |
| 17 | 18 | COIN COUNTER B | |
| COIN SWITCH B | 19 | 20 | VIDEO SYNC |
| + 12 VOLTS | 21 | 22 | + 12 VOLTS |
| + 12 VOLT | 23 | 24 | + 12 VOLTS |
| SPEAKER (-) | 25 | 26 | SPEAKER (+) |
| 1P CONTROL PUSH 2 | 27 | 28 | 2P CONTROL PUSH 2 |
| VIDEO RED | 29 | 30 | VIDEO GREEN |
| VIDEO BLUE | 31 | 32 | |
| 2P CONTROL UP | 33 | 34 | 2P CONTROL DOWN |
| 1P CONTROL UP | 35 | 36 | 1P CONTROL DOWN |
| SERVICE SWITCH | 37 | 38 | COIN SWITCH A |
| + 5 VOLTS | 39 | 40 | + 5 VOLTS |
| + 5 VOLTS | 4l | 42 | + 5 VOLTS |
| GROUND | 43 | 44 | GROUND |
KID NIKI INSTALLATION & SERVICE MANUAL PAGE 11
DATA EAST EDGE CONNECTOR PIN—-OUT
HARNESS CONNECTOR, EMI FILTER PCB
| SOLDER SIDE | PIN NUMBERS | COMPONENT SIDE | |
| 2P_ CONTROL 2 DOWN | A | 1 | IP CONTROL 2 DOWN |
| 2P CONTROL 1 UP | B | 2 | 1P CONTROL 1 UP |
| 2P CONTROL 3 LEFT | Cc | 3 | 1P_ CONTROL 3 LEFT |
| 2P CONTROL 4 RIGHT | D | 4 | 1P CONTROL 4 RIGHT |
| 2P_ CONTROL 7 PUSH 3 | E | a | _1p CONTROL 7 PUSH 3 |
F 6 H il
| TEST SWITCH | J | 8 | SERVICE SWITCH |
| 2P CONTROL 5 PUSH 1 | K | 9 | 1P CONTROL 5 PUSH 1 |
| 2p CONTROL 6 “PUSH 2 | L | 10 | 1p CONTROL 6 PUSH 2 |
| . 2P_START SWITCH | M | 11 | LP START SWITCH |
| COIN SWITCH 2 | N | 12 | COIN SWITCH 1 |
| COIN COUNTER 2 | P | 13 | COIN COUNTER 1 |
| VIDEO GREEN | R | 14 | VIDEO BLUE |
| VIDEO SYNC | $ | 15 | VIDEO RED |
T 16
| SPEAKER (-) | U | 27 | SPEAKER (+) |
| = 5 VOLTS | Vv | 18 | +12 VOLTS |
| +_5 VOLTS | W | 19 | + 5 VOLTS |
| +_5 VOLTS | r | 2 | + 5 VOLTS |
GROUND fa 2 GROUND
| GROUND | Z | 22 | GROUND |
EDGE CONNECTOR TERMINAL NUMBERING:
12345678 9011281415617 18 B 20222
| == | fen feslaieaials | i= | =. |
O RSS sae SSeS SSSSSEE= iS} ABCODEFHJKLMNPRSTUVYWXY2Z
CONNECTOR CR7E-44DA-3.96 E (HIROSE)
| BI | BS | Bi | BIS | B20 B22 |
| Al | AS | an | AIS | A20 A22 |
CONNECTOR 1168-044-009 (KEL)
PAGE 12 KID NIKI INSTALLATION & SERVICE MANUAL
d. Specific wiring information.
GRN
| [ar > | re) | 1P DOWN |
vEL,
| B2 | O | IP uP |
ORG [es ->-———_—+$ —________________» 1e LEFT RED °
| Ba | —o | 1P RIGHT |
BRN
| Bu | 5 | IP START |
RED/WHT oO 2P START
| BO | t | o-~o | IP SHOOT 1 (word) |
vio t o~o IP sHcoT 2 Gump) B16,
Cx GROUND
CONTROL. PANEL
+12V G5v)
12 (Ss) vouT 2 CS) VOUT COIN COUNTER COIN COUNTER:
COIN COUNTER |
CON GUNTER 2
SPEAKER +
SPEAKER. —
COIN 1
COIN 2.
GROONP
ICOIN MECH DOOR ‘
> = EMI FILTER PCB EDGE CONNECTER
KID NIKI INSTALLATION & SERVICE MANUAL PAGE 13
- PCB SCHEMATICS
PAGE 14 KID NIKI INSTALLATION & SERVICE MANUAL
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
Bos Fh TROMVHONOD OWN
afi
tb}J-s}-—}~\
yO = AAS
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
MC14584.
Bros, “IND wee” aioe Ener anor» Bro ME2-T- Pa bly
zno Tree
LW a> $20 (oa) sor270) Ale
TESCRIPTION PIANO Nanao CORPORATION
03260 (avo. / > (602266) Calo. 29]
ay
G&) (BO £819 OLCA M62-7-C AR LPR FittitZ Fave
ir)
= yony SAL 4S "LOO OWN H.R A Udk-a TE
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
wo i ceroensag ] Lu toy
fet
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
inn =~ 2h