CATHODE RAY TOMES

Pac-Pack Field Conversion Kit (M051-00127-A011) Jumpshot

PAC-PACK (Bally Midway) · Field Conversion Kit · 23 pages · 9 sections · original scan

Page 1

Wha Shot

PAC-PACK

Field Conversion Kit Instructions

For PAC-MAN U.R. & MS. PAC-MAN U.R

MS. PAC-MAN U.R.

Crally MIOWAY MFG. CO. 10601 W Belmont Avenue Franklin Park, Illinois 60131 U.S.A, Phone (312)451-9200 Cable Address MIDCO Telex No. 72-1596

MO51-00127-A011

Page 2
WARNING THIS GAME MUST BE GROUNDED. FAILURE TO DO SO MAY RESULT IN DESTRUCTION TO ELECTRONIC COMPONENTS.
WARNING: This equipment Generates, Uses and can Radiate Radio Frequency Energy and if not installed and used in accordance with the Instructions Manual, may cause interference to Radio Communications. As temporarily permitted by Regulation it has not been tested for compliance to Subpart J or Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference. Operation of this equipment in a Residential Area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.

ELECTRICAL BULLETIN: FOR ALL APPARATUS COVERED BY THE CANADIAN STANDARDS ASSOCIATION (CSA) STANDARD C22.2 NO. 1, WHICH EMPLOYS A SUPPLY CORD TERMINATED WITH A POLARIZED 2-PRONG ATTACHMENT PLUG.

CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET

EXposUae BLADES CAN BE FULLY INSERTED TO PREVENT BLADE

ATTENTION: POUR PREVENIR CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR. UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT, SAUF S! LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT.

Cully MIDWAY

OUR TOLL FREE NUMBER FOR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER BALLY/MIDWAY™ GAME YOU NOW HAVE ON LOCATION.

CALL US FOR PROMPT, COURTEOUS ANSWERS TO YOUR PROBLEMS

ANSWERS TO YOUR PROBLEMS.

Video or Pinball - Continental U.S. 800-323-7182 Billy MIDWAY 10601 West Belmont Avenue Franklin Park, Illinois, 60131 phone (312) 451-8200

© COPYRIGHT MCMLXXXV BY BALLY MIDWAY MFG. CO. ALL RIGHTS RESERVED.

NO PART OF THIS PUBLICATION MAY BE REPRODUCED BY ANY MECHANICAL, PHOTOGRAPHIC, OR ELECTRONIC PROCESS, OR IN THE FORM OF A PHONOGRAPHIC RECORDING, NOR MAY IT BE TRANSMITTED, OR OTHERWISE COPIED FOR PUBLIC OR PRIVATE USE, WITHOUT PERMISSION FROM THE PUBLISHER. THIS MANUAL IS FOR SERVICE USE ONLY, AND NOT FOR GENERAL DISTRIBUTION. FOR PERMISSION REQUESTS, WRITE: BALLY MIDWAY MFG. CO., 10601 W. BELMONT AVE., FRANKLIN PARK, iL 60131.

Printed in U.S.A.

_ ta — ae

Page 3
WARNING

The parts contained In this field converston kit must be Installed without deviation from the instructions contained in thls manual and kit. Failure to follow these instructions In every detail may result In the creation of illegal interference to radio and TV reception.

BALLY MIDWAY Mfg. Co. has verIfied that thls field conversion kit, when installed In the game(s) specified In this manual, comp!les with the requirements in Part 15 of the FCC rutes for a Class A computing device. Operation of thls equipment In a residential area may cause unacceptable Interference to radio and TV reception, requiring the operator to take whatever steps are necessary to correct the interference.

BALLY MIDWAY Mfg, Co. will not be responsible for incomptete or improper conversions, or Installation In a game for whIch this fleld conversion kit Is not Intended. If this field conversion kit Is installed in a game that Is not specified In this manual or in a previously converted game, the operator Is required to take whatever steps are necessary to Insure compliance with the requirements in Part 15, Subpart J, of the FCC Rules for a Class 4 computing device.

SPECIAL NOTE:

DO NOT DISCARD ANY OF THE PARTS YOU REMOVE

EN MAKING THE MODIFICATIONS EXPLAINED IN THIS MANUAL. DO WH!

THEY WILL BE RE-USED IN FUTURE CONVERSION KITS!

Page 4

PAC-MAN TO "PAC-PACK" GAME

CONVERS ION PROCEDURE

PLEASE NOTE: NEW GAME information (parts list, electrical! drawings and option switch settings Is provided In your conversion kit).

To convert your PAC-MAN game to the NEW GAME Is a falrly simple operation. Just follow the steps below and the I!lustrattons given In each figure.

1.

2.

3.

4,

5.

6.

8.

9%.

10.

WwW. Turn the power off to your game and disconnect It from Its wal! outlet.

Opening the cabinet: Unlock and open the rear access door.

Main Game Logic Board removal:

  • Disconnect the Main Game Logic Roard from all Its cabling (see Figure 1).
  • Remove the P.C.B. clamp Indicated In Flgure 2 and silde the Main Game Logic Board out of the cabinet.

instal! the Potted CPU Module Support Bracket as Indicated In Figure 3.

Cut the plastle securing strap and remove the "PIGGY BACK" module Indicated In Figure 4, IF YOUR GAME IS EQUIPPED WITH ONE. IF IT IS NOT equipped with one, sImply proceed to step 6 below.

Remove the Z-80 CPU from the Main Game Logic Board as shown In Figure 5. BE CAREFUL NOT TO BEND ITS PINS! Return this CPU to your stock. It may be used as a spare part.

Remove the sIx EPROMS and 2 PROMS located as shown In Figure 6 and set them aside. BE CAREFUL NOT TO BEND THEIR PINS! Replace the removed EPROMS and PROMS with the ones supp!led In your conversion kIt. They are Installed as shown In Figure 6.

Insta!! the ribbon cable on the Potted C.P.U. Module so that It dressed out on the side AWAY FROM THE POINT on the module (see Figure 7). Install! the other end of the ribbon cable Into the empty socket on the Maln Game Logic Board that was left when you removed the Z-80 CPU from It In step 6 (see Figure 7).

If your game was equipped with a "PIGGY RACK" module that you removed In step 5, relnstal! It at this time (see Figure 8). If It was not equipped with one, simply proceed to step 10.

Relnstal! the Maln Game Logic Board and the Potted C.P.U. Module (now attached to It by the ribbon cable) back Into the game cabinet.

Install the Potted C.P.U. Module to the four plastic snap-In mounting stand-offs of the Potted C.P.U. Module Support Bracket as shown In Figure 9,

Page 5

12.

13.

15.

16.

NOTE:

18.

20.

NOTE: Reconnect al! previously removed cabling to the MaIn Game Logic Roard EXCEPT for the OLD MASTER CABLE and the OLD CONTROL PANEL CARLE.

Remove the existing Control Pane! as explained In your OLD GAME manual.

Control! Panel Mounting Brackets (left & right) MUST be Installed In your PAC-MAN game cabinet. Refer to Figure 10 for Installation Instructions.

Replace the OLD GAME MaIn-Display-Glass with the Maln-DIsplay-Glass provided In your conversion kit. Follow the procedure as explained In your OLD GAME manual.

Secure the NEW GAME Controt Panel by !atchIng the two clamps on the Contro! Pane! to the strikes of the game cabinet.

A NEW GAME Master Adaptor Cable wit! supplement the existing Master Cable for wiring between the new Control Panel and the Maln Game Logic Roard. Refer to NEW GAME WIRING DIAGRAMS provided with your conversion kit for any necessary wiring modifications. Cut leaf pins on new cabling wires where splicing Is necessary.

Fasten the wires of the NEW GAME Master Adaptor Cable to the existing Master Cable's 44-pin connector. Run the cable along the existing master cable to the NEW GAME Control! Panel by usIng the cable tie wraps provided In the kit. Secure the 44-pIn connector to the MaIn Game Logic Roard.

Secure the nine position connector of the new Control Panel's cable to that of the Master Adaptor Cable. Secure the twelve position connector of the new Control Panel's cable to that of the exIsting Master Cable.

Close and tock the game cabInet and plug It back Into Its wal! outlet.

Turn the game on and let It warm up for a few minutes. Run a Self-Test on It and play a couple of games to be sure everything Is working properly.

NO NOT FORGET to save the sIx EPROMS and two PROMS you removed In step 7 of this procedure. Put them in the packaging that the new EPROMS and PROMS came In and store them In a dark place at room temperature. They wil! not be harmed If stored thls way. Thus, by reversing thls procedure, you could convert your game back to a PAC-MAN mode! If you ever wanted to.

Page 6

DISCONNECT CABLING

A UPRIGHT

REMOVE CLAMP TO SLIDE P.C.B. QUT

UPRIGHT

Page 7

POSITION BRKT. IN THIS AREA AND SCREW INTO SIDE OF CABINET WITH 2 SCREWS INSERT STANDOFFS AS SHOWN (4)

UPRIGHT

Page 8

CUT PLASTIC STRAP AND LIFT SMALL P.C.B. (PIGGY BACK) OFF OF MAIN BOARD

  • Figure 5
Page 9

REMOVE (6) EPROMS AND REINSERT NEW EPROMS SUPPLIED WITH KIT. (LOCATIONS 5E, 5F, 6E, 6F, 6H & 6J)

IMPORTANT! REMOVE (2) PROMS

NOTE LOCATION AND REINSERT NEW OF NOTCH ON PROMS SUPPLIED ALL 1.C.s REMOVED WITH KIT. BEFORE INSERTING (LOCATIONS 4A & 7F)
Page 10

INSERT RIBBON CABLE INTO SOCKET AS SHOWN

REINSTALL “PIGGYBACK" MODULE TO MAIN P.C.B.

NOTE LOCATION OF NOTICES IN 1.C.’s
Page 11
NOTE: MOUNT MODULE 90 DEGREES COUNTER-CLOCKWISE FROM POSITION SHOWN.

PUSH SECURE C.P.U. MODULE ONTO STANDOFFS AS SHOWN.

UPRIGHT

CONTROL SHELF MOUNTING BRACKETS ~ LEFT & RIGHT

MOUNTING FOR PAC-MAN CABINET ONLY.

GONTROL SHELF MOUNTING BRACKET | 7 STEP 2: REMOVE SCREWS FROM LOCATOR RIGHT SIDE: 0£18-00101-0100 \ BRACKET AND USE THEM FOR LEFT SIDE: 0E18-00101-0200 . HOLDING MOUNTING BRACKET. . LOCATOR BRACKET MAY BE DISCARDED.

STEP 3: ~ PUSH MOUNTING aracKey UP TIGHT TO EDGES SHOWN. /S NOW PUT TOP 2 SCREWS IN PLACE. EXISTING CLAMP: FINALLY, SECURE CLAMP TO MOUNTING BRACKET WITH EXISTING SCREWS. STEP 1: REMOVE CLAMP FROM CABINET AND SAVE ALL OF IT’S PARTS. STEP 4: REPEAT STEPS 1 THRU 3 TO INSTALL CONTROL PANEL MOUNTING BRACKET ON OTHER SIDE. EXISTING a LOCATOR BRACKET / (2 PIECES)

Page 12

3. INSTALLATION OF REMAINDER OF CONVERS {ON KIT PARTS

Turn the power to the game off. Remove the OLD GAME Header Glass by removing the three screws which secure the top bracket In place. Install the Header Glass provided In your conversion kit.

A.

B.

* DECAL INSTALLATION NOTES (Strongly Recommended) :

APPLICATION NOTE: The use of the plastic squeegee provided In your kit Is required to put on ALL decals.

The cabInet's surface should be cleaned of ALL dirt and grime. This Is necessary to Insure proper adheston.

A toam type wetting agent should be app!ied to the cabInet's surface before mounting the decal.

Install the Front Decal* as IndIcated In Figure 11.

instal! the two SIde Decals *, referring to Figure 12, as follows (the left side & then the right stde):

Ae

B.

c.

D.

E. Set the game cabinet on Its side (for ease of decal application).

Pee! back the bottom of sIx Inches of the IIner (heavy waxed backing sheet) and apply the decal at the bottom of the game cabinet while IInIng up the decal with the rear edge of the cabinet. This Is Important as the Side Decal matertal Is only 1/2 Inch wider than the width of the game cabInet.

Remove the !Iner while working out the alr bubbles and tIniIng up the decal with the rear edge of the cabinet.

Lift the game upright and trim off the excess decal material.

Repeat steps A through PD for Installation of the other Side Decal.

Page 13

FRONT DECAL

STEP 1: PEEL BACK TOP 6° OF LINER. NOW STICK DECAL TO CABINET. —=__ TEP 3: TRIM TO FIT

STEP 2: LINE UP DECAL WITH THESE EDGES. NOW REMOVE LINER WHILE WORKING OUT ALL AIR BUBBLES. FINALLY, TRIM EXCESS WHERE REQUIRED.

STEP 4: TRIM TO FIT MS, PAC-MAN ONLY.

KICK PLATE ON MS. PAC-MAN ONLY.

Page 14

SIDE DECALS - LEFT & RIGHT

MAKE SURE THAT 1/2” OF 1/2". BLACK DECAL MATERIAL OVERLAPS AT THIS POINT.

1° MAX. 37/4" MIN. BELOW CABINET

(1/2" BLACK MATERIAL OVERLAP)

“We

Page 15

MS. PAC-MAN TO "PAC-PACK" GAME

CONVERS ION PROCEDURE

PLEASE NOTE: NEW GAME Information (parts !tist, electrical drawings and option switch settings) Is provided In your conversion kit.

To convert your PAC-MAN game to the NEW GAME is a fairly simple operation. Just follow the steps below and the I{ltustrations given In each Figure.

2.

3.

5.

8.

a Turn the power off to your game and disconnect it from its wall outtet.

Opening the cabinet: Unlock and open the rear access door.

Main Game Logic Board removal:

  • Disconnect the Main Game Logic Roard from all its cabling (see Figure 1).
  • Cut the plastic securing strap and remove the "PIGGY BACK" module Indicated In Figure i, IF YOUR GAME IS EQUIPPED WITH ONE, and set it aside.

° Remove the ribbon extension cable from the Main Game Logic Board.

"Remove the P,C.B. clamps indicated in Figure 2 and s!ide the Malin Game Logic Board out of the cabinet.

Remove the six EPROMS and 2 PROMS located as shown In Figure 3 and set them aside. BE CAREFUL NOT TO BEND THEIR PINS! Replace the removed EPROMS and PROMS with the ones supplied in your conversion kit. They are Installed as shown In Figure 3.

Instat! the ribbon cable on the Potted C.P.U. Module so that It dressed out on the side AWAY FROM THE POINT on the module (see Figure 4). Instal! the other end of the ribbon cable Into the empty socket on the Main Game Logic Board that was left when you removed the original ribbon cable in step 3 (see Figure 4).

\f your game was equipped with a "PIGGY BACK" module that you removed in step 3, reinstal! I+ at this time (see Figure 5). If I+ was not equipped with one, simply proceed to step 7.

Remove the Auxlliary Game Logic Board from its support posts and return it to your stock for possible future use (see Figure 6).

Reinsta!! the Main Game Logic Board and the Potted C.P.U. Module (now attached to it by the ribbon cable) back Into the game cabinet.

tnstal! the Potted C.P.U. Modute to the four plastic snap-in mounting stand-of fs of the Potted C.P.U. Module Support Bracket as shown In Figure 7.

Page 16
  • Reconnect al! previously removed cabling to the MaIn Game Logic Board EXCEPT for the OLD MASTER CABLE and the OLD CONTROL PANEL CABLE.
  • Remove the existing Contro! Panel as explained In your OLD GAME manual.
  • Replace the OLD GAME Main-Display-Glass with the Maln-DIsplay-Glass provided In your conversion kit. Follow the procedure as explalned In your OLD GAME manual.
  • Secure the NEW GAME Control Panel by latching the two clamps on the Control! Pane! to the strikes of the game cabinet.
NOTE: A NEW GAME Master Adaptor Cable wi!! supplement the existing Master Cable for

14,

15.

16.

7, wiring between the new Control! Panel and the Main Game Logic Board. Refer to NEW GAME WIRING DIAGRAMS provided with your conversion kIt for any necessary wiring modifications. * Cut leaf pins on new cabling wires where splicing Is necessary.

Fasten the wires of the NEW GAME Master Adaptor Cable to the exIsting Master Cable's 44-pIn connector. Run the cable along the exIsting master cable to the NEW GAME Contro! Pane! by usIng the cable tle wraps provided In the kIt. Secure the 44-pin connector to the Maln Game Logic Roard.

Secure the nIne position connector of the new Contro! Panel's cable to that of the Master Adaptor Cable. Secure the twelve position connector of the new Control! Panel's cable to that of the exIsting Master Cable. *®

Close and tock the game cabinet and plug It back Into Its wall! outlet.

Turn the game on and let It warm up for a few minutes. Run a Self-Test on It and play a couple of games to be sure everything Is working properly.

NOTE: DO NOT FORGET to save the six EPROMS and two PROMS you removed In step 7 of this procedure. Put them In the packaging that the new EPROMS and PROMS came In and store them In a dark place at room temperature. They will not be harmed If stored this way. Thus, by reversing this procedure, you could convert your game back to a PAC-MAN mode! If you ever wanted to.

Two Versions of Ms. Pac-man exists. Version "A" Is powered by a Transformer Board. Version "B" Is powered by a 125VA Power ChassIs. Please observe the wiring differences between the two Versions. The contro! panel cable Is wired for Version "A" only. RewlriIng of the contro! panel cable Is necessary for VersTon "Bt, (Please refer to the appropriate wiring diagram for "repInning" of the twelve position connector.)

Page 17

REMOVE “PIGGY-BACK” es DISCONNECT MODULE AND : : ’ CABLING RIBBON CABLE : FROM MAIN LOGIC BOARD

MAIN LOGIC BOARD

UPRIGHT

REMOVE CLAMP TO SLIDE P.C.B. OUT

UPRIGHT

Page 18

REMOVE (6) EPROMS AND REINSERT NEW EPROMS SUPPLIED WITH KIT. (LOCATIONS 5E, 5F. 6E. 6F. 6H & 64)

IMPORTANT! REMOVE (2) PROMS

NOTE LOCATION AND REINSERT NEW OF NOTCH ON PROMS SUPPLIED ALL |.C.s REMOVED WITH KIT, BEFORE INSERTING (LOCATIONS 4A & 7F)

A5-

Page 19

sulla} A. PF ae INSERT RIBBON CABLE INTO SOCKET AS SHOWN

REINSTALL “PIGGYBACK” MODULE TO MAIN P.C.B.

NOTE LOCATION OF NOTCHES IN 1.C.'s
Page 20

REMOVE AUXILIARY GAME LOGIC BOARD FROM POSTS UPRIGHT

NOTE: MOUNT MODULE 90 DEGREES COUNTER-CLOCKWISE FROM POSITION SHOWN.

PUSH SECURE C.P.U. MODULE ONTO STANDOFFS AS SHOWN.

Page 21

i.

3. INSTALLATION OF REMAINDER OF CONVERSION KIT PARTS

Turn the power to the game off. Remove the OLD GAME Header Glass by removing the three screws which secure the top bracket In place. instal! the Header Glass provided In your conversion kit.

*® DECAL INSTALLATION NOTES (Strongly Recommended) :

APPLICATION NOTE: The use of the plastic squeegee provided In your kit Is required to put on ALL decals.

The cabInet's surface shoutd be cleaned of ALL dirt and grime. This Is necessary to Insure proper adheslon.

A foam type wetting agent should be app!led to the cabInet's surface before mounting the decal.

Instal!! the Front Decal* as Indicated In Figure 8.

Install the two Stde Decals *, referring to Figure 9, as follows (the left side & then the right side):

A.

Be

C.

D. Set the game cabInet on Its stde (for ease of decal app!Ication).

Peel back the bottom of six Inches of the liner (heavy waxed backing sheet) and apply the decal at the bottom of the game cabinet while lining up the decal with the rear edge of the cabInet. This Is Important as the Side Decal matertal! Is only 1/2 Inch wider than the width of the game cabinet.

Remove the IIner while working out the alr bubbles and ltining up the decal with the rear edge of the cabinet.

LIft the game upright and trim off the excess deca! material.

Repeat steps A through D for Installation of the other Side Decal.

=18-

Page 22

FRONT DECAL

STEP 1: PEEL BACK TOP 6” OF LINER. NOW STICK DECAL TO CABINET. —___ STEP 3: TRIM TO FIT

STEP 2: LINE UP DECAL WITH THESE EDGES. NOW REMOVE LINER WHILE WORKING OUT ALL AIR BUBBLES. FINALLY, TRIM EXCESS WHERE REQUIRED.

STEP 4: TRIM TO FIT MS. PAC-MAN ONLY.

KICK PLATE ON M8, PAC-MAN ONLY.

19+

Page 23

SIDE DECALS — LEFT & RIGHT

MAKE SURE THAT 1/2” OF 1/2". BLACK DECAL MATERIAL OVERLAPS AT THIS POINT.

MIN. BELOW CABINET

(1/2" BLACK MATERIAL OVERLAP)