CATHODE RAY TOMES

P47

P-47: The Phantom Fighter (World) (Jaleco, 1988) · Document · 8 pages · 6 sections · original scan

Page 1

INSTRUCTION MANUAL

P-47™ is a horizontal conversion kit

P-47™ is a trademark of Jaleco USA Inc. ©1988 Jaleco Ltd.

Page 2

P-47™ is a one or two player

horizontal video game. A list of

components and instructions are provided with this kit for your ease of installation. Using your existing cabinet and monitor, your finished product should look and play like a new game.

Jaleco, USA

KIT CONTENTS Description Part # PCB, P-47™ 1521 8-Way Rotary Joystick Red Pushbutton Assemblies Yellow Pushbutton Assemblies Wiring Harness 1525 PCB Cage (FCC required) 1526 P-47™ Marquee 1527 Side Pane! Graphics (Left & Right) 1528 Control Pane! Overlay 1529 Underlay Card (CRT} 1530 Control Pane! instruction Card 1531 Instruction Manual

SPECIFIC REQUIREMENTS

Monitor — Horizontal, Negative Composite Sync Input

Power Supply — +5 VAC @ 7 Amp +12 VAC @ 1 Amp -5 VAC @ 5 Amp (Min)

Page 3
WARNING
  • Make sure power is OFF
  • Monitor and coin acceptors are functional
  • Make sure game is properly grounded ) )
  • Never expose PC board to direct sunlight ) )
  • Do not use tester to check PC board

INSTALLATION INSTRUCTIONS

Cabinet

@ Remove all graphics from pre-existing game. Inspect cabinet for any gouges or chips. Fill in as required with wood putty. Wipe cabinet clean and repaint if necessary. e Apply the side graphics, using a straight edge as a guide line. Apply the decals to each side of cabinet.

@ Using the old marquee from the previous game, place it on top of the new one. Mark to proper size, making sure that the title “P-47™" is not excluded. Proceed to cut the plexi. Before installing the marquee replace ail burned-out bulbs. Control Panel

e@ Remove control panel and remove old buttons, joysticks, and wiring. Strip off the old lexan overlay and any vinyl stickers. Prepare control panel surface by using sandpaper, making sure that the surface remains from the previous game are completely gone. Figure 1 is a suggested panel layout—use it if possible (if not, use your own discretion). Any remaining holes that are not being used, fill with wood blocks, putty, cardboard or epoxy. @ Apply the overlay to the control panel, making sure no air bubbles are present. Next, install the buttons stickers on the control panel in their proper locations. Replace joysticks and buttons and return control panel to the game.

START

OO Machine — Special 1 2 © Machine Special

Gun Weapon Gun Weapon (*) Push 1 Push 2 O O 8) Push 1 Push 2 O O O Figure 1 Control Panel Layout Two 8-Way Joysticks Left-hand button to fire the machine gun Right-hand button to utilize other weapons

Page 4

WIRING PROCEDURES

© Disconnect the old wiring harness from the CPU board. Remove the board. Carefully

note the function of each wire. Use the schematic from the previous game. Label all wires to avoid confusion.

To wire the P-47™ kit into the cabinet, the following steps are provided: @ Leaving several inches of wire from the old wiring harness at each connector, cut the wires near the game’s coin door, monitor, player panel, speaker and power supply. Do NOT cut the other side of these wires at the CPU board end.

@ An edge-connector schematic drawing is provided in this manual for your ease of rewiring. @ Using the new wiring harness, solder wires to the coin door, monitor, control panel, speaker and power supply, making sure all connections are taped to avoid them shorting out.

WIRING TO POWER SUPPLY

e Locate the +5V leads color-coded RED and install them to the proper position on the power supply. @ Next, locate the +12V leads color-coded BLUE and install them to the proper position on the power supply as well. e Last, position a BLACK ground wire from the harness and connect it. A continuous ground wire should be installed to every electronic component.

Page 5

SETTING DIP SWITCHES

® Before installing the PCB refer to the dip switch setting, and adjust the game to the specifications %, @ Sound may also be adjusted by turning the volume contro! either clockwise or counterclockwise.

INSTALLING THE FCC CAGE ASSEMBLY

®@ Mount the FCC cage to the inside wall of the cabinet, making sure that there is no direct heat source and good ventilation, if not, damage to the board will result and void the warranty. @ Next mount the PCB making sure the edge-connector has enough room for connection.

@ Plug the wiring harness onto the CPU board. Use plastic wire guides to support the harness.

@ Position the FCC cage over the PCB and secure it with screws to the cabinet, making sure no wires are pinched. @ Before you apply power to the game, remove the main harness edge connector from the PCB.

© Appiy power to the game and measure the +5 volts at the edge connector and adjust to +5,15 VAC using a digital multi-meter. Measure the +12 and -5 VAC wires to be certain they are connected properly. Turn power off to game and re-connect the edge connector. Turn on power to the game and coin it up. Test all the controls and sound for proper operation.

SERVICE INFORMATION

To obtain replacement parts, please contact your distributor. For technical service contact Jaleco’s customer service department during the hours of 9 AM - 5 PM Central Time at (312) 647-7077. Thank you for your purchase of a Jaleco USA Inc. P-47™.

Page 6

Edge Connector:Diagram

(Edge Connector of Jamma Specs.)

Hoadfhoris L&R Ee 7 ey

+12V

Key To Prevent

Erroneous Insertion Coin Meter #1

Speaker 1 (+) Headphone L (+)

Video Red Video Blue Video GND

Coin SW #1 1P Start 1P Up 1P Down 1P Left 1P Right 1P Push 1 1P Push 2

Speaker 2 (+) Headphone R (+) InmmoQg WY

>RDQANTMNXXS<CHMDVZES -rAc GND GND

+5V +5V

+12V

Erroneous Insertion Coin Meter #2

Speaker 1 (-)

Video Green Video Sync Service Switch

Coin SW #2 2P Start 2P Up 2P Down 2P Left 2P Right 2P Push 1 2P Push 2

Speaker 2 (-) The Phantom Fighter P-47™

DIP SW

VOLUME

STEREO) VOLUME MONO. (SPEAKER 1)

Page 7

The Phantom Fighter P-47™

Be sure to turn off the power before resetting DIP switches. Porswitch#if tt 2 8 1 Coin - 1 Credit OFF |OFF 1 Coin - 2 Credits 1 Coin -3 Credits 1 Coin - 4 Credits 2 Coins - 1 Credit 3 Coins - 1 Credit First Coinchute

4 Coins - 1 Credit OFF | ON | ON ON [ON [ON 1 Coin -1 Credit — 1 Coin - 2 Credits 1 Coin -3 Credits Second 1 Coin - 4 Credits Coinchute {2 Coins - 1 Credit 3 Coins - 1 Credit 4 Coins - 1 Credit | Free Pla

Attract Mode |Unecessary ll Player's Destructible Plane Invulnerable H+ i | 2 | Number of ON JOFF Planes for OFF Players OFF ON Not Used | |

Difficulty Level More Difficult Easy Not Used Screen Display

Page 8

2802-279 (Zl) XV4 2202-279 (ZLE) TAL 87909 “I ‘SeIIN "IS PAeMOH "M LOS OosTUr ‘NOLLVTIVLSNI dO AWIL AHL LV GNNOYSD OL GSLVNINYAL ONV G3aZINILN 43d LSNW LIX NOISHSANOD SIHL HLIM GallddNS ADVO GHVOd Od AHL “AONSYASYALNI SHL LOAWYOO OL AYVSSAOAN JYvV Sd31lS YSASLVHM 4MVL OL YHOLVHAdO FHL ONIWINDOAY ‘NOILda035Y¥ AL GNV OIdVH OL JONSYSSYALNI AIEVLdSDOVNN 3SNVO AVW AONVIIdWOO YO4 GalsIHaA YO GAYNLOVANNVW OS LON AWVS YSHLO ANV OL NOILOANNOO YO LIX SIHL 40 NOILOANNOO Y3d0OudNI “ADIAAG ONILNdWOD V SSV19 V YOd SA1NY 994 dO St LuVd NI SLNSWSYINDAY HLIM SONVIIdNWOD ¥O4 G3ISIHSA N33g SAVH HOIHM £86! ‘b HAEOLOO Y4a14V GSYNLOVANNVW SAWYS O3dIA GalvH4ad0 -NIOOD NO AINO 3SN YOs GAQNSLNI SI LIM SIHL AJONVIIdWOO NOILVINDAY (9'O4

ONINYVM

NOILYWAWHOSNI Y3SN