CATHODE RAY TOMES

Namco Classics Vol 1

Namco Classic Collection Vol.1 (Namco, 1995) · Document · 6 pages · 12 sections · original scan

Page 1

OPERATION MANUAL

A\ CAUTION In order to safely use this machine, be sure to carefully read this operation manual and the manual of the cabinet in which this machine to be installed before installation and operation. This operation manual should be kept together with the machine.

NAMCO LIMITED 2-8-5 TAMAGAWA, OHTA-KU, TOKYO, 146, JAPAN DISTRIBUTED BY:

© 1995 NAMCO LTD., ALL RIGHTS RESERVED

Page 2
  • Vaullons
  • Be sure to tum off the cabinet whenever installing or removing the PC board. Otherwise you may be hurt by an electric shock.
  • Be sure to use an edge connector which is applied to the JAMMA standard. Any modifications such as cutting the edges of PC boards will cause a failure and also will be out of our guarantee for repair.
  • Never test the PC boards for conductivity with a multimeter or similar device. The PCB contains sensitive chips which could be destroyed even by the intemal voltage of such a device.
  • Foreign matters or dust on the PC boards will cause a failure. Tum off the power and clean the PC boards with a brush or similar thing.
  • When transporting the PC boards, wrap them with sponges or air caps and pack them in a card board box so that they can avoid a direct impact from outside during shipment.
  • For maintenance, contact your distributor.
  • Specifications LP, Start 2P.Start
  • Control panel: One-side 2-P specifications + 8-direction lever: 2 (IP, 2P, 1 each) + Button switch: 4(1P, 2P, 2 each) =a + Start switch: 2 (IP, 2P, 1 each)
  • PC board size: 230 x 210 mm /* oom bid ao A
  • Direction of monitor: Vertical l 2P.button switch? 2P.button switch]

2P,8-direction

3.Connection

  • Connection of control panel See above to connect JAMMA hamess and extended hamess(accessory) to control panel through the cabinet (see P5 : PC board connector table) Connecting expanded hamess to the right speaker allows you to enjoy a stereophonic effect.
  • Connection of PC board Set the PC board in the cabinet and connect JAMMA edge connector and 48P extended edge connector (DDK 225D-10024C2-2312) to the PC board.

4. Explanation of PC Boards 48Pextendededge 56P edge connector

connector (JAMMA)

  • Option switches TT}, No.1 to "ON" for Test Mode. 12 fo) No.2 to "ON" for Screen Freeze. Normally, all of the option switches are “OFF”. NJ Speaker volume: \ Option switch

(2) Speaker volumes om Brightness volume

To decrease the sound volume of the speaker, tum the Do not use brightness volume speaker volume counter-clockwise. Fig.2

  • Test Mode
  • The PC Board enters the test mode by setting the test switch on the PC Board to "ON" on the game screen. And the test menu screen is displayed on the monitor. Use the test switch (For connection, see PS: PC Board Connector Table) on the cabinet or

the option switch on the PC Board. (see PI: 4.(1) Option switches)

When an item is selected by operating the 1P control lever up and down and the IP button switch is pushed, the selected testscreen is displayed.

  • Game fees can be changed on the coin option screen, and the game difficulty can be changed on the game option screen. Select an item by operating the 1P control lever up and down, and change its contents using the 1P button switch1 (see the option setting table). After that, push the 1P button switch2 to return to the test menu screen.

a

Page 3

SWITCH TEST 1_ (a) Switch test sereen SOUND TEST +~(b) Sound test sereen COIN OPTIONS +~(c) Coin option screen (Setting of game fees) . GAME OPTIONS 1 (d) Game option sereen (Setting of game difficulty) OBJECT TEST +(e) Object test screen

SCROLL TEST +—(f) Scroll test screen CONVERGENCE TSTE (i) Cross hatch pattern (for monitor adjustment)

ADS. f(g) A.D.S. sereen COLOR TEST }~(h) Color test screen (for monitor adjustment)

(Test Menu Screen)

r (COIN OPTIONS} {GAME OPTIONS}

GAME COST:1MUSIC IN ATTRACT:—$

1COIN 1 CREDIT YES

DISCOUNT TO CONTINUE:+— 2SPEAKER UT—____——}-—1 0

STEREO.

COINMECH VALUE :——3COIN COUNTER:p——1 1

_ 1 COIN COUNT AS 1 COIN ‘COMMON COIN 2 MECH VALUE +4 1 COIN COUNT AS 1 COIN OLD GALAGA OPTIONS; 2 COIN 3 MECH VALUE 5 NEW GALAGA OPTIONS} — | 3 1 COIN COUNT AS | COIN OLD XEViOUS OPTIONS} i4

COIN 4 MECH VALUE =p68‘SUPER XEVIOUS OPTIONS:}—15
  • COIN COUNT AS I COIN NEW XEVIOUS OPTIONS} 1 6 BONUS FOR QUANTITY BUY IN-—————7 OLD MAPPY OPTIONS | 7 NEW MAPPY OPTIONS} | 8 rae LAY: 8

) (Coin Option Screen) (Game Option Screen) (Option Setting Table) ( < Standard Setting) Item Contents

1. Game fees‘one count required for one game (one credit)1<[1-9]
2. DISCOUNT50% discount when continuing a playNO < YES
3. COIN 1 MECH VALUE‘Count per coinT<[i-9
4,COIN2 MECH VALUE‘Count per coinT<[1-9]

5.6. Not used —

7. BONUS COINGne additional coin per the specified numberof[NONE < 2 Coins Give 1 Coin~9 Coins

coins Give 3 Coins

  • FREE PLAY NO< YES

9,MUSIC IN ATTRACT YES < NO 10.SPEAKER OUT STEREO < MONO COMMON ( 1Coin counter for 2slots)<

  • COIN COUNTER: EACH ONE ( 1Coin counter for each slot)
  • OLD GALAGA OPTIONS Push 1P button switch to enter OLD GALAGA OPTIONS screen: a
  • NEW GALAGA OPTIONS Push 1P button switcht to enter NEW GALAGA OPTIONS screen———D 14.0LD XEVIOUS OPTIONS Push 1P button switch! to enter OLD XEVIOUS OPTIONS screen
  • SUPER XEVIOUS OPTIONS [Push 1P button switch! to enter SUPER XEVIOUS OPTIONS screen—————-C T6.NEWXEVIOUS OPTIONS Push 1P button switch’ to enter NEW XEVIOUS OPTIONS screen

17.0LD MAPPY OPTIONS Push 1P button switcht to enter OLD MAPPY OPTIONS screen 18.NEW MAPPY OPTIONS Push 1P button switch to enter NEW MAPPY OPTIONS screen————¢

Game fees Credit (Note), @ 2 a4 display ®, Tgame Continue 1o Coin Mech 1&2in

100 yen}100 yenTCOINICREDIT[NO}1COUNT ICOIN(ONE|CREDITOuse.

Example

100 yenSO yen[2 COINS ICREDIT |YES|1COUNT 2COINSINONE | CREDIT 0/2
Page 4

leiiieiinibtthd. AiinichaateRRmiietthen, jail tial tetaliai tala deticiol [OLD GALAGA OPTIONS} INEW GALAGA OPTIONS]

DIFFICULTY LEVEL: ant DIFFICULTY LEVEL: 19

NORMAL NORMAL

: FIGHTER: 24 Ramee 20 } FIGHTERS . EXTEND: 25 BUT STAGE at Ist somoprs ND 200000PTS.

FIGHTER & EXTEND: 22 3 FIGHTERS (1432)

IST 30000 PTS 2ND_ 120000 PTS EVERY 120000 PTS

(Option Setting Table) (< Standard Setting)

Item Contents

1.9. DIFFICULTY LEVEL INORMAL < [NORMAL, EASY,HARD, VERY HARD]

  • RANK UP increase difficulty from 32nd stage IO< YES.

2.1. FINAL STAGE Set final stage to end a game compulsorily 31 < [31,63,95,ENDLESS]

2 3. DIFFICULTY LEVEL FIGHTERS 1ST 30000PTS 2ND 120000PTS EVERY 120000PTS < (initial 3,add 1 at 30000 points another 2 2. FIGHTER & EXTEND it 120000, hereafter 1 for every 120000 points) selectable from 32 patterns} IORMAL < [EASY, NORMAL, HARD)

  • FIGHTER 8 <(2,3,4,5]
  • EXTEND 1 ST 50000P TS 2ND 200000PTS < [NO BONUS, 1ST 50000PTS, 1ST S0000PTS 2ND 200000PTS]

¢ Original Xevious Option Screen (Super Xevious Option Screen)

DIFFICULTY LEVEL: HARD {OLD XEVIOUS OPTIONS]

NORMAL

SOLVALOU: RANK UP: YES

FINAL LAP: 1 LAP

SPECIAL FLAG: 1UP 1 TIME

SOLVALOU & EXTEND: 3 SOLVALOU (36/36)

1ST 20000 PTS

(Option Setting Table) {NEW XEVIOUS OPTIONS]

DIFFICULTY LEVEL:

3 SOLVALOU d Arranged Xevious Option Screen

(< Standard Setting) . Item Contents

2.6. DIFFICULTY LEVEL IHARD < [NORMAL, EASY, HARD, VERY HARD] (Default setting of Super Xevious is VERY HARD)

  • RANK UP Increase difficulty from 2nd lap YES <NO.

2 8. FINALLAP Set final lap to end agame compulsorily |1LAP <{1LAP,2LAP,3LAP,4LAP, ENDLESS}

2.9. SPECIAL FLAG UP |}OO0OPTS Set effect of Special Flag UP 1 TIME < (1UP,once at a place) UP. aq (add 10000points)

3.0. SOLVALOU & EXTEND {selectable from 36 patterns} 3.1. DIFFICULTY LEVEL NORMAL <[EASY, NORMAL, HARD] Ig SOLVALOU 1ST 20000PTS < (initial 3,add 1 at 20000 points)

3.2. RANK UP B<[2,3,4,5]

Page 5

{ .Arrange Mappy Option Screen {OLD MAPPY OPTIONS} {NEW MAPPY OPTIONS] DIFFICULTY LEVEL: 3 3 DIFFICULTY LEVEL-—————;————3 6

NORMAL. NOKMAL

FINAL ROUND: 3 4 Mappy: —————_- 3 7 15 ROUND 3 MAPPY MAPPY & EXTEND: j}———3 5 EXTEND 38 3MAPPY (5/32) HOPTS

1st 20000 PTS

(Option Setting Table) ( < Standard Setting) Item Contents Le SRIGIIVTEVED NGC CIEASYNORMALTAROAROSTRARGZFAROSRAROGRARDVST | 3.4. FINAL ROUND ISet final round to end a game compulsorily H5 <[15,23,31,39, ENDLESS)

3.5. MAPPY & EXTEND Sie eeeaea 3,add 1 at 20000 points)

eG IEE ROR CEASOMMALIART OCSC~=“‘COSONSC#”SC*‘“‘CONSN#N#CNC#C#C#‘d’! 3.7. MAPPY 3 <[2,3,4,5} 3.8. EXTEND IG0000PTS < [NO BONUS, 60000PTS]

Page 6

Eee

JAMMA edge connector (S6P 3.96 mm pitch) ‘Solder side Terminal No. | Parts side

GNDA1GND

GND B 2 GND

450c345V
45VD445V

E 3

+120F6+12V
insertion errorH7.jinsertion error
[preventing.reventing
{Coin counter 2J8= counter 1
K9Coin lockout 1
Speaker ©L10Soeaker (+)
iAudio (GND?M11[Audio
fideo GREENN12|Video RED
ideo SYNCP13__|Video BLUE

Service switch R 14 [Video GND

$ 15 _ [Test switch

[Coin switch 2T16(Coin switch 1
OP start switchU17__[IP start swich
BP lever UPVv18|IPlever UP
2P lever DOWNWw19|IPlever DOWN
QP lever LEFTx20 [IP lever LEFT
BP lever RIGHT¥21|IPlever RIGHT

bP button Switchi | Z | 22 |iPbutton Switchi

BP button Switch2 | a23|iPbutton Switch2

b 24 € 25

:d26
GNDe27GND
GNDt28GND

+ Do not connect anything to the blank connectors. + Both lockout solenoid and coin counter operate on +12V. + Connect the switches to N.O. terminals such as a microswitch, and the GND to the COM terminal.

CoM N.O. NC.

+ The supply voltage is available within +5%. For use in the best condition, get the supply voltage as close to the specified voltage as possible.

(Recommended power capacity)

+5V 45% 2.5A or more +12V 45% 2.0A or more Extended edge connector (48P 2.54 mm pitch)

Solder side Terminal No. = Parts side

Speaker R(-) [VEL] | Al BI raker R (+) [ORG] AR B2 A3 BR AS Be jasertion error ro BS [insertion error preventing key preventing key 6 Be AT B7 ae BS

Ad BY ALO BlO All Bil Aid| Bid ais | Bid Al4 Bid Ais | BIS AIS BI6 ai? | BIT ALB BIg Ais B19 ; ~ ‘A20 B20 All Bl A22 B22 aR | Ra Aza | Bot

{Connection to stereo cabinet] (1)STEREO / MONO setting Select SPEAKER OUT in the game option screen at the test menu screen.

<Caution>Monophonic cabinets do output only the left-hand sound even if the stereophonic setting is selected

  • Connection to speakers + Connect the (L) speaker to the speaker output of 56P edge connector (JAMMA) on the PC board. + Connect the (R) speaker to Speaker R (+), (-) of 48P extended edge connector.
  • Use a DDK 225D-10024C2-2312 as a 48P extended edge connector.