CATHODE RAY TOMES

Kicker Conversion Kit Instruction Manual

Kicker (Konami, 1985) · Instruction Manual · 12 pages · 27 sections · original scan

Page 1

* KICKER CONVERSION KIT *

INSTRUCTION MANCAIL

Konami Inc. KICKER™ and Konami. are registered

1555 BRUMMEL AVENUE, ELK GROVE VILLAGE, IL 60007 trademarks of Konami Industry Co., Ltd. TELEPHONE: (312) 364-6633 FAX: (312) 364-1368 TELEX: 6871385 KONAM UW i, i

Page 2

Konami Inc. Konami.

Ben Har-El President

Dear Operator:

There are 1.5 Million CHILDREN REPORTED MISSING each year in America. Some of these children are players in our Arcades.

We at Konami fee] that it is our responsibility to participate in combating this Real and Growing problem. Won't You Help Us Find The Children?

Konami is working in cooperation with CHILD FIND, IN., a not-for-profit corporation organized to aid parents, legal authorities and the F.B.I. in the finding of missing children. In an effort to do so, we have attached to our kits and video games, a poster and a decal showing photos of children that are listed with Child Find as missing.

Because of the tremendous exposure your gameroom or location can provide, we ask that you PROMINENTLY DISPLAY the posters and place the decals on each of the Konami games. We, and the parents of these children are very greatful for any help that you give us in assisting this extremely important program.

If it is possible for you to assist Child Find further by sending a tax deductible donation or if you would like to volunteer any time or services, please contact Child Find at:

CHILD FIND, IN. P.O. BOX 277 New Paltz, NY 12561 Phone: (914) 255-1848

Again, thank you very much for helping us to help find the children. We deeply appreciate your concern and cooperation.

Best regards,

KONAMI INC.

Ben Har-El President

PLEASE DON'T FORGET TO DISPLAY THE POSTERS AND DECALS!

1555 BRUMMEL ELK GROVE VILLAGE, ILLINOIS 60007 PHONE: (312) 364-6633 TELEX: 6871385 KONAM UW FAX: (312) 364-1368

Page 3

TABLE OF CONTENTS

Page Page

Conversion Kit Contents ................. 1 Monitor Info... 0.0.0... ccc eee eee 5

Table of Contents.................--005. 1 Wiring Harness Color Code............... 6

Introduction... 0... 2... 0. cece eee eee 2 Wiring Diagram ........ 2.0.0... 0 cece eee 7

Recommended Control Panel Layouts... ... 2 Technical Information .................0. 8

Graphics... ccc eee wean ete ncesnene 3 Dip Switch Setting..................00.. 9

Monitor Specifications .................. 4 User Information Warning........ Back Cover

CONVERSION KIT CONTENTS:

MAIN PRINTED CIRCUIT BOARD P.C.B. CAGE (FCC REQUIRED) CONNECTING WIRING HARNESS 6 SETS — BUTTON ASSEMBLIES 4-WAY JOYSTICK MARQUEE (HEADER) (1/8” acrylic sheet) ONE SET SIDE PANEL GRAPHICS (left & right) CONTROL PANEL OVERLAY CONTROL PANEL DECALS instruction decals/button decals (2 sets) MANUAL REGISTRATION CARD

REPLACEMENT ACCESSORIES ARE AVAILABLE THROUGH YOUR DISTRIBUTOR.

THIS KIT USABLE FOR COCKTAIL AND UPRIGHT VIDEO GAMES WITH A RASTAR SCAN MONITOR WHICH IS OR CAN BE MOUNTED VERTICALLY.

Page 4

KICKER INTRODUCTION

a ——————— EEE Ee

KONAMI CONVERSION KITS are the most complete conversion kits available today. Every detail has been carefully considered, designed and packaged to provide you the means of easily producing a professional conversion.

These kits have all the accessories to easily convert your UPRIGHT or COCKTAIL video game.

We strongly urge you to FULLY STUDY this instruction manual BEFORE you begin your conversion. It contains step-by-step instructions, schematic diagrams and suggestions on how to install your Konami Conversion Kit and maximize your profits. KICKER can be installed in any vertically mounted rastar scan monitor game.

Everything you will need to construct your new game is provided in this kit. All accessory parts — wiring harness, joystick, etc. are custom made for KICKER by top engineers experienced in the coin-op industry. A 4-way joystick (as provided) MUST be used.

The Player Instruction and Button Control decals are made of a non-destructible acrylic material specifically to keep the player from peeling them off. Should you convert a cocktail table game, KICKER is supplied with 2 sets of button decals.

SAVE YOURSELF TIME AND MONEY

The following P.C.B.’s are interchangeable with KICKER P.C.B.’s Super Cobra * Scramble * Pooyan * Locomotion ¢ Circus Charlie Lil Hustler ¢ Juno First ¢ Time Pilot * Gyruss * Tutankham Turtles Super Basketball * Mega Zone * Pandora’s Palace « Time Pilot ’84 © Track ‘n’ Field « Hypersports Frogger (60% — check pin print-out) ¢ Amidar * Roc ’N Rope * The End . In other words, your KICKER will plug right into existing edge connectors of the games listed above — be sure to check your pin print-out. (Keep in mind that Kicker is designed as a vertical game.)

NEW FEATURE — DUAL CONTROL By moving SW#2 of dip switch bank #3 to the “on” position, you are now in the dual control upright mode. This allows you to set up an upright game with two sets of controls rather than one set. The first set of controls should be hooked up to the 1P set of wires; the second set to the 2P wires (see wiring diagrams). Each player still challenges the “computer-controlled” opponent (alternating play). This does not allow simultaneous interaction of players on the video screen.

SINGLE CONTROL LAYOUT

sstaat 2 2PSTART DUAL CONTROL LAYOUT

estart <> > avstanr ety T sty Be aes Q&S aGa?PFfafan 22

Page 5

PUTTING YOUR BEST GAME FORWARD

PREPARATION: For best results, all old graphics should be removed completely from the cabinet. “Stick-on” graphics can be removed by using a hairdryer or hot air device. The heat from the dryer will loosen the adhesive, allowing you to easily peel them off — any adhesive residue can be cleaned off with acetone and a soft dry cloth. (DO NOT USE ACETONE ON SURFACES PAINTED WITH FLAT PAINT).

TOOLS YOU NEED:

  • Foaming Aerosol (such as “Windex”).
  • Soft Squeegee.
  • X-Acto Knife.

SIDE PANEL DECALS

  • Spray area of cabinet where Side Panel decals are to be applied with foaming aerosol or a mild soap solution. . Remove protective backing from decals. . Position decals into place. . With a soft squeegee, beginning from the center of the decal, slowly and evenly press out excess foam until you achieve a smooth finish. BON
  • Allow to set approximately 2 to 3 hours before handling. Maximum adherence is achieved in 48 to 72 hours.
  • Trim side decal to fit your cabinet.

CONTROL PANEL OVERLAY:

  • Refer to Recommended Control Panel Layout on page 4. . Drill any new holes needed. . Plug any holes that will not be used. (A permanent epoxy filler works well for this step.)
  • Pre-position the overlay prior to removing the backing.
  • Slowly apply the overlay — inch by inch on the control panel, removing the backing as you apply it.
  • Once it's in place, by using an X-Acto knife, cut around the button and joystick placements.

INSTRUCTION/BUTTON DECALS: Apply the Player Instruction, Button and 1 Player/2 Player decals in their respective positions. Apply Pressure liberally. Allow to set as long as possible before putting game on location. won

NOTE: Maximum adherence is achieved in 48 to 72 hours.

MARQUEE

(WEAR PROTECTIVE GLASSES WHILE TRIMMING MARQUEE) 1/8” Acrylic Marquee should be cut to fit your game. DO NOT remove protective mask until this is done.

One way of cutting your Marquee is as follows: (Be sure to protect painted side of Marquee from any surface which may scratch or mar finish).

CUTTING WITH A KNIFE OR SCRIBER Acrylic sheet up to 3/16” thick may be cut by a method similar to that used for cutting window glass. Use a scriber of some kind — a scribing knife such as the one pictured, a metal scriber, an awl, or even a sturdy craft knife — to score the sheet. Draw the scriber several times (7 or 8 times for a 3/16” thick piece) along a straight edge held firmly in place. It is best not to remove the protective masking. Make the cuts carefully using firm, even pressure. For best results make each stroke cleanly off the edge of the sheet. Then, clamp the acrylic sheet or hold it tigidly under a straight edge with the scribe mark hanging just over the edge of a table. Protect your hands with a cloth, and apply a sharp downward pressure to the other side of the sheet. It will break along the scratch. Scrape the edges to smooth any sharp corners. This method is not recommended for long breaks or thick material.

Break sheet over edge of table after scribing. Always draw the scribing knife along a straight edge.

Page 6

KICKER: MONITOR SPECIFICATIONS

Kicker requires a vertically mounted monitor. It also generates composite negative sync. If your monitor is composite positive sync, you will have to change to composite negative sync.

  • To alternate composite positive sync to composite negative sync, use 7404 IC or 74LS04 IC. The signal on the output pin from the P.C.B. is a combination of H-sync and V-sync.
NOTE: Please refer to Figure 2.

FIGURE 2: +5V

FROM P.C. BOARD

NEGATIVE COMPOSITE SYNC. OUTPUT TO MONITOR (PIN 14 on P.C.B EDGE) POSITIVE COMPOSITE SYNC.

(+ 5V and GND should be taken out of the P.C. Board.)

  • Separate Sync modification for KICKER if your monitor has “Separate Sync” input. (For example “Electrohome brand” and Wells-Gardner brand.”) Step 1 WIRING HARNESS

NEGATIVE SYNC INPUT a VIDEO SYNC Lae

If the picture is still not stable... Step 2 Prepare Hook-up wire. (For example “Electrohome brand.”) WIRING HARNESS

wi VIDEO SYNC

Page 7

KICKER: MONITOR INFO.

el

SERVICE INSTRUCTIONS

NOTE: All monitors are equipped with automatic degaussing coils (L701) which demagnetize the picture tube every time the monitor is turned on after being off for a minimum of 5 minutes. Should any, part of the chassis become magnetized it will be necessary to degauss the affected area with a manual degaussing coil. Move the coil slowly around the CRT face and all surrounding metal parts. Then slowly withdraw for a distance of 6 feet before turning off.

1.0 BLACK LEVEL CONTROL ADJUSTMENT This control has been set at the factory and should not need further attention, however, when the game is connected a slight adjustment of VR201 may be necessary to obtain the proper black level (the black portion of the picture just extinguished).

2.0 VERTICAL SIZE (HEIGHT) Location of this control is shown in Fig. 1. This control must be adjusted slowly, if necessary, until the picture or test pattern attains the correct vertical proportions.

3.0 CIRCUIT PROTECTION A 4.04 pigtail fuse, mounted on the Main Board has been provided to protect the Power Output Circuit.

4.0 FOCUS Adjust the focus control, located on the HV unit (T352), for maximum over-all defination and fine picture detail.

5.0 HORIZONTAL HOLD CONTROL ADJUSTMENT, VR351 (See Fig. 1) A warm-up period of at least five minutes should be allowed before alignment is carried out. With the monitor being driven from the game signal, short TP601 to TP31. Adjust VR351 until the picture stops sliding horizontally. Remove the short.

6.0 HORIZONTAL VIDEO POSITION If the video is off center on the raster some compensation can be made by adjusting this control.

7.0 VERTICAL RASTER POSITION ADJUSTMENT If the video is off center vertically, (short dimension of picture tube) some compensation can be made by moving the vertical raster position adjustment jumper to either positions “U” or “D”,

8.0 HORIZONTAL RASTER POSITION ADJUSTMENT If the video is off center horizontally (long dimension of the picture tube) some compensation can be made by moving the horizontal raster position adjustment jumper to either positions “R” or “L”. 9.0 HORIZONTAL WIDTH ADJUSTMENT The horizontal width coil is a hexagonal tuning too! adjustment. This control must be adjusted slowly, if necessary, until the picture or test pattern attains the correct horizontal proportions.

  • KONAMI GAMES ARE ALL NEGATIVE COMPOSIT SYNC. USE THE THREE PIN CONNECTOR ON THE MONITOR.

—19"— RED DRIVE GRN DRIVE REO CUTOFF GRN CUTOFF’. BLU CUTOFF

*NEG H SYNC

  • NEG V SYNC +GND
NOTE: WHEN USING COMPOS. ITE SYNC USE HORIZ. SYNC INPUTS, POS H SYNC POS V SYNC. GND BLU

GRN REO HORIZ HOLD

BLK LEVEL

HORIZ VERT VERT VERT HORIZ CENTERING SIZE HOLO RASTER RASTER SHIFT SHIFT

FIGURE 1

Page 8

KICKER: WIRING HARNESS

WIRE COLOR KEY:

Unlettered Side

Lettered Side

—___}———_>

(Solder Side)

(Parts Side)

RED/GREEN RED/YELLOW BROWN/YELLOW VIOLET/WHITE ORANGE/WHITE RED/WHITE BLUE/WHITE BLACK/WHITE RED/GRAY GRAY/WHITE WHITE/PINK GREEN/BROWN RED/BROWN BLACK BLACK RED *Cocktail Table or Dual Control

Upright Only (EMPTY) SPEAKER OUT

  • 2P KICK
  • 2P LEFT 1P START 4P JUMP 1P KICK 1P RIGHT 1P UP COIN 1 1P DOWN (NOT USED) VIDEO GREEN VIDEO RED (EMPTY) GND GND + 5V DC qPo;o;a;wyujy ry 7) <}/4) Ss) Z2;0o;ac;n}r) a) > + 12V DC SPEAKER OUT 2P JUMP * 2P RIGHT* 2P START 2P UP* SERVICE SW 1P LEFT 2P DOWN* COIN 2 COIN COUNTER 1 COIN COUNTER 2 VIDEO BLUE VIDEO SYNC (NOT USED) GND GND + 5VDC (BASE COLORILINE COLOR) ORANGE ORANGE/GREEN ORANGE/YELLOW BLUE/YELLOW VIOLET/YELLOW BLACK/YELLOW ORANGE/GRAY BROWNMWHITE GRAY/YELLOW BLUE/GRAY GREEN/GRAY YELLOW/GRAY BLUE/BROWN WHITE/BROWN YELLOW/PINK BLACK BLACK RED
Page 9

KICKER

WIRING DIAGRAM

BF ENCT APPLICABLE] 2A 3a a Cipy REGIRED POWER CAPACITY

4al2W 45 12W, 4nl2w BW GaeW né6W

D Dr FAL PA] -—— PARTS SIDE | poe SIDE Ba +12V

SPEAKER OUT

2P JUMP

same as /P CONTROLS

only for TABLE. TYPE

2P_KICK 2P JUMP *

2P_ RIGHT a] alele 2P KICK

2P LEFT 2P_START 2P LEST ®

1P START 2P START

[—. 2P UP * IP START 2p UP ® 1P JUMP

CONTROLS for 2P = SERVICE SWITCH FO 0 SERVICE

2P GAME START 1° GAME START 2P DOWN * Hi

2 HS | 2s CGIN COUNTER

yUMP KICK aignt [LP YUMP | 2V COIN COUNTER

cert [Le KICK ue IP_LEFT

g © Down [LL RIGHT iP UP 1p.

CONTROLS for IP

  • NOTES — () IP NOL player 2P NO.2 player
  • surge killer diodes for COIN COUNTER instolled on the PC.8.. *Cocktail Table or Dual Control

Upright Only BLUE! /4| l/5|

GREE! conor Sree MONITOR RED +12V} POWER SUPPLY +5V(5A) GND /8| IP KICK IP LEFT IP RIGHT 2P DOWN iP UP COIW 2 COIN | COIN COUNTER I IP DOWN COIN COUNTER 2 *

BLUE GREEN SYNC RED GND GND GND GND +5V +5V EDGE CONNECTOR 5/32 INCH PITCH

Page 10

KICKER: TECHNICAL INFORMATION

  • Required Power Capacity

+5V DC 7A or more.

+12V DC See Figure 1 below

Figure 1:

Required Power Capacity 82 EW BQ6W BREW 4.212W Jew 42 Dr | Be

a

  • Signal output at R(red) analog, positive — G(green) analog, positive

B(blue) analog, positive Te

Sync. H-V composite negative H Vv

DIAGNOSTIC PROCEDURES AUTOMATIC SELF-TEST — Upon “Power On”, this system will automatically test ROMS and VIDEO RAMS. The screen will display pass or conditions as follows: ROM 1 OK ROM 2 OK = TEST PASSED

RAM 1 OK RAM 2 OK= TEST PASSED

If there is a poblem, before contacting your distributor:

  • Check that all chips on board and wiring connections are tight.
  • Check output from power supply at the board. (Do not just check at the power supply as voltage drops may occur over the length of the wire.) MANUAL TEST — A more detailed five step diagnostic may be performed by moving SW3 of Dip Switch Bank #3 to the “on” position while power to game is off. Turn power “on” and proceed as follows:
  • COLOR TEST The screen will display V RAM color & OBJ color blocks. If a block shows any irregularities (e.g., lines or dots in color blocks), this could be due to a failure of VIDEO RAM, COLOR RAM, or OBJ CIRCUITS. Use these blocks to further adjust monitor focus and colors.

ag

  • SWITCH TEST From color test, press One Player Start and the screen will display all switches with a zero (0) to the right. When a switch is activated the zero (0) should change to a one (1).
  • COIN COUNTER TEST From switch test, press One Player Start and the screen will display “coin counter’. While number one (1) is shown, counter one should pulse eight times. When number two (2) is shown, counter two should pulse eight times also.
  • DIP SWITCH SETTINGS Press Player 1 and the screen will display most of the programmable features with their respective settings. These settings should correspond to the positions of the dip switches.
  • SOUND TEST From dip switch settings, press One Player Start. The game will go through all sounds of Kicker’s program.

TO EXIT DIAGNOSTICS — TURN POWER OFF AND RETURN SW3 TO OFF POSITION. THEN TURN POWER BACK ON.

Page 11

DIP SWITCH SETTINGS

DIP SW No. 1 Settings Coin 1 Switch Set Coin 2 Switch Set

SW4321COIN PLAY |SW8765COIN | PLAY
.OFF | OFF | OFF | OFF11 |°OFF | OFF | OFF | OFF11
OFF | ON12OFF ; ON12
ON | OFF13ON | OFF13
ONON14ONON14
OFF | ON | OFF | OFF15OFF | ON | OFF | OFF15
OFF | ON16OFF | ON16
ON | OFF17ON | OFF17
ONON21ONON21
ON | OFF | OFF | OFF23ON | OFF | OFF | OFF23
OFF |; ON25OFF | ON25
ON | OFF31ON | OFF31
ONON32ONON32
ONON | OFF | OFF34ONON | OFF | OFF34
OFF | ON41OFF | ON41
ON | OFF43ON | OFF43
ONONFREE PLAYONON | INVALIDITY

DIP SWITCH NO. 2 SETTINGS THE NUMBER OF PLAYER'S LIFE

SW12 ‘|NUMBERSOUND IN ATTRACT MODE
OFF | OFF2SW8SOUND
.ON | OFF3OFFOFF
orF | ON5* | ONON
ONON7

CHANGE OF TABLE OR UP-RIGHT DIP SWITCH NO. 3 SETTINGS

sw3TYPEVideo Screen Flip

OFF [ TABLE SW 1

«[ONUP-RIGHT~lorry.NORMAL
BONUS SETONUPSIDE DOWN
sw| 4]5BONUS POINTSSingle/Dual Control Upright
¢ [OFF]OFF|at 30,000 Pts. & Every 70,000 Pts. Thereaftersw2TYPE
ON [OFF |at 40,000 Pts. & Every 80,000 Pts. Thereafter¢| OFFSINGLE UPRIGHT CONTROL
OFF on |40000 PTSONDUAL UPRIGHT CONTROL
ON | ONoeono PTsGame Test Mode
Difficulty of the GameLl3MODE
sw]6[7DIFFICULTY*[OkGAME MODE
OFFI OFFEASYONCHECK MODE
*[ON |OFFNORMAL*SW 4: NOT USED

OFF] ON DIFFICULT

ON | ONVERY DIFFICULTe9

JS Tj eSHOWS NORMAL SETTING

Page 12

USER INFORMATION

WARNING

F.C. C. REGULATION COMPLIANCE

THE PC. BOARD CAGE* SUPPLIED WITH THIS CONVERSION KIT MUST BE UTILIZED AND TERMINATED TO GROUND AT THE TIME OF INSTALLATION.

THIS IS TO AVOID RADIO FREQUENCY RADIATION AND COM- PLY WITH THE LIMITS FOR A CLASS “‘A” COMPUTING DEVICE PURSUANT TO SUB-PART “J” OF PART 15 OF F.C.C. RULES, WHICH ARE DESIGNED TO PROVIDE REASONABLE PROTEC- TION AGAINST SUCH INTERFERENCE WHEN OPERATED IN A COMMERCIAL ENVIRONMENT.

OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE INTERFERENCE - IN WHICH CASE, THE USER AT HIS OWN EXPENSE, WILL BE REQUIRED TO TAKE WHATEVER MEASURES MAY BE REQUIRED TO CORRECT THE INTERFERENCE.

*The P.C.B. Cage furnished with this kit has been designed by Konami to afford easy access to the board. Once installed, the cage can be opened by simply removing 2 screws.

Konami.

1555 BRUMMEL AVENUE, ELK GROVE VILLAGE, IL 60007 TELEPHONE: (312) 364-6633 FAX: (312) 364-1368 TELEX: 6871385 KONAM UW